E M C C o m p o n e n t s December 2015 Common Mode Filters For signal line ZJYS51 Series ZJYS51R5 Type Caution The products in this catalog will be or have been stopped production Discontinue Issue Date Nov.4, 2015 Last Purchase Order Date Sep.29, 2017 Last Shipment Date Mar.30, 2018 Please refer to our Web site about replacement information.

(2/9) E M C C o m p o n e n t s REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. n SAFETY REMINDERS e Please pay sufficient attention to the warnings for safe designing when using these products. e b REMINDERS e The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH v or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. a n Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). h o Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature r i does not exceed 150°C. o t c Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shoretening may ocucur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to b d the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. o Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal l design. l r Carefully lay out the coil for the circuit board design of thei non-magneticp shield type. w A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body througdh the grounding wire. Do not expose the products to magnets or magnsetic fields. e t Do not use for a purpose outside of the contents regulated in the delivery specifications. p c The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications p equipment, home appliances, amusemeunt equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under da normal operaotion and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringento level of safety tor reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. s If you intend to use the prodructs in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each cataplog, please contact us. (1) Aerospace/Aviation equipment (8) Public information-processing equipment e (2) Transportation equipment (cars, electric trains, ships, etc.) (9) Military equipment (3) Medical equhipment (10) Electric heating apparatus, burning equipment (4) Power-generation control equipment (11) Disaster prevention/crime prevention equipment T (5) Atomic energy-related equipment (12) Safety equipment (6) Seabed equipment (13) Other applications that are not considered general-purpose (7) Transportation control equipment applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. 20151221 / cmf_commercial_signal_zjys51r5_en.fm

(3/9) E M C C o m p o n e n t s Common Mode Filters Product compatible with RoHS directive For signal line Overview of ZJYS51R5 Type n e e FEATURES b Optimal common mode filter for removing noise without straining the transmission signal and for tra nsmitting high-quality signals. Optimal countermeasure for common mode noise induced during data transmission for digital siegnal processing such as in PCs and telephones. v SMD type structure makes it optimal for surface mounting. Up to 2A current is allowable, so it can be used as a noise countermeasure for power supaply lines. n h APPLICATION o PCs, telephones, LANs, ISDNs, digital PBXs, game machines, CTVs, CD-ROMs, 8mrm video cassiette recorders, etc. o t c PART NUMBER CONSTRUCTION e u ZJYS51R5 - 2P T - 01 b d Product internal Series • Type name code Packaging style Internaol code 2P l 01 2PB T ø330mml reel r 2PL i p 4P w M4PA d OPERATING TEMPERATURE RANGEs, PACKAGeE QUANTITY, PRODUCT WEIGHT t Temperature range p Package quantity Individual weight Operating c Storage Type temperature temperature(cid:2) p （°C） u （°C） (pieces/reel) （g） ZJYS51R5-2PT-01 –25 to +85 –25 to +85 1,500 0.4 ZJYS51R5-2PBT-01 –25 to +d85 –o25 to +85 1,500 0.4 ZJYS51R5-2PLT-01 –25 to +85 –25 to +85 1,500 0.4 ZJYS51R5-4PT-01 –25o to +85 t–25 to +85 1,000 0.8 ZJYS51R5-M4PAT-01 –25 to +85 s–25 to +85 1,000 0.8 (cid:2)(cid:3)The Storage temperature range irs for after the circuit board is mounted. p e h T RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://product.tdk.com/en/environment/rohs/ Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20151221 / cmf_commercial_signal_zjys51r5_en.fm

(4/9) E M C C o m p o n e n t s ZJYS51R5 Type RECOMMENDED REFLOW PROFILE n Preheating Soldering Natural cooling e Peak e T4 b e ur T3 T3 at er e p m e T T2 v T: t3 a T1 n h t1 t2 o r i o t t: Time c e u Preheating Soldering Peak b d Temp. Time Temp. Time Temp. Time T1 T2 t1 T3 t2 T4 t3 o 150°C 180°C 60 to 120s 230°C 10 to 30s 245°C 5s l l r i p w d s e t p c p u d o o t s r p e h T Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20151221 / cmf_commercial_signal_zjys51r5_en.fm

(5/9) E M C C o m p o n e n t s ZJYS51R5-2PT-01, -2PBT-01, -2PLT-01 SHAPE & DIMENSIONS 5.5max. n 4 3 e Marking: TDK e Marking: Product internal code b Marking: Production date code e 9±0.5 1 2 6.86max. v a max. max. h n 5.08 4.57 0.25 o 2.54±0.25 (0.6) r i 1.3 o t c Dimensions in mm e u b d o l RECOMMENDED LAND PATTERN l CIRrCUIT DIAGRAM i p 4 3 w d 6.79.9 s e 1.8 t p 1 2 c • No polarity 6 1. p u 2.54 Dimensions in mm d o o t s r p e h T Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20151221 / cmf_commercial_signal_zjys51r5_en.fm

(6/9) E M C C o m p o n e n t s ZJYS51R5-2PT-01, -2PBT-01, -2PLT-01 ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE n Part No. ZJYS51R5-2PT-01 ZJYS51R5-2PBT-01(cid:2)1 ZJYS51R5-2PLT-01(cid:2)2 Rated voltage Edc(V) 50 50 50 e Rated current (A) 2 2 2 Test voltage Edc(V) e 125 125 250 [Between terminals for 5s] Insulation resistance (M(cid:4)) b 100 min. 100 min. 100 min. [Between terminals at DC.50V for 1min] DC resistance ((cid:4)) [1 line] 0.12 max. 0.12 max. 0.10 max. Impedance ((cid:4))[+5 to +35°C] 200 min.[20 to 300MHz] 300 min.[6 to 20MHz] e 100 min.[20 to 100MHz] ○Measurement equipment v Measurement item Product No. Manufacturer Common mode impedance 4991A Agilent Technologies a DC resistance 4338A Agilent Technologies n h Insulation resistance 4339A Agilent Technologies o ＊ Equivalent measurement equipment may be used. r i o t c e u b d o l IMPEDANCE VS. FREQUENCY CHARACTERISTICS (FORl 1 ELEMENT)r i p 10000 w d 2PB Commosn mode e2PT Common mode 1000 t p Ω) c (ce u 2PL Compmon mode n 100 a ed d o p m I o t s2PL Differential mode 10 r 2PT Differential mode p 2PB Differential mode 1 e 1 3 10 30 100 300 1000 Frequency (MHz) h ○Measurement equipment T Product No. Manufacturer 4991A Agilent Technologies ＊ Equivalent measurement equipment may be used. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20151221 / cmf_commercial_signal_zjys51r5_en.fm

(7/9) E M C C o m p o n e n t s ZJYS51R5-4PT-01, -M4PAT-01 SHAPE & DIMENSIONS 10.5max. n 8 7 6 5 e Marking: Production date code e Marking: Product internal code b 1 2 3 4 9±0.5 e 6.86max. v 5.08max. 4.57max. 0.25 ha n o 2.54±0.25 (0.6) 1.3 r i o t c Dimensions in mm e u b d o l l r i p RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM w ZJY S51R5-4PT-01 ZJYS51R5-M4PAT-01 d 8 7 6 5 8 7 6 5 s e 6.79.9 t p 1.8 c p u 6 1. 1 2 3 4 1 2 3 4 2.54 2.54 2.54 d o • No polarity • No polarity Dimensions in mmo t s r p e h T Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20151221 / cmf_commercial_signal_zjys51r5_en.fm

(8/9) E M C C o m p o n e n t s ZJYS51R5-4PT-01, -M4PAT-01 ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE n Part No. ZJYS51R5-4PT-01 ZJYS51R5-M4PAT-01 Rated voltage Edc(V) 50 50 e Rated current (A) 2 0.5 Test voltage Edc(V) e 125 125 [Between terminals for 5s] Insulation resistance (M(cid:4)) b 100 min. 100 min. [Between terminals at DC.50V for 1min] DC resistance ((cid:4)) [1 line] 0.12 max. 0.25 max. Impedance ((cid:4))[+5 to +35°C] 200 min.[20 to 300MHz] 200 min.[20 to 300MHz] e ○Measurement equipment v Measurement item Product No. Manufacturer Common mode impedance 4991A Agilent Technologies a DC resistance 4338A Agilent Technologies n h Insulation resistance 4339A Agilent Technologies o ＊ Equivalent measurement equipment may be used. r i o t c e u b d o l IMPEDANCE VS. FREQUENCY CHARACTERISTICS (FORl 1 ELEMENT)r i p 10000 w d 1000 s e4PT Common mode M4PA Common mode t p Ω) c (e p c u n 100 a ed d o p m I o t s 10 r 4PT Differential mode p M4PA Differential mode 1 e 1 3 10 30 100 300 1000 Frequency (MHz) h ○Measurement equipment T Product No. Manufacturer 4991A Agilent Technologies ＊ Equivalent measurement equipment may be used. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20151221 / cmf_commercial_signal_zjys51r5_en.fm

(9/9) E M C C o m p o n e n t s ZJYS51R5 Type PACKAGING STYLE REEL DIMENSIONS n 2.0±0.5 E e Type A W1 W2 N E ZJYS51R5-2 ø330±4/–2 16.4+e2/–0 22.4max. ø100±1 2 typ. ZJYS51R5-4P,M4PA ø330±4/–2 16.4+2/–0 22.4max. ø100±1 2 typ. b N e v 1.0 a n h ø13.0±0.5 W1 o ø21.0±0.8 W2 r i A o t c Dimensions in mm e u b d TAPE DIMENSIONS o øD0 P2 P0 t E l l r i p F w W B d A P1 s K e t p c Dimensions in mm Type A B u øD0 pE F P0 P1 P2 W K t ZJYS51R5-2 5.8±0.1 9.8±0.1 1.5+0.1/0 1.75±0.1 7.5±0.1 4.0±0.1 8.0±0.1 2.0±0.1 16.0±0.3 5.2 0.4 ZJYS51R5-4P,M4PA 9.8±0.1 10.5d±0.1 1.5+0.1/o0 1.75±0.1 7.5±0.1 4.0±0.1 12.0±0.1 2.0±0.1 16.0±0.3 5.2 0.4 o t 500 to 560 s 160min. Taping r 240min. p Drawing directione h T Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20151221 / cmf_commercial_signal_zjys51r5_en.fm