PRODUCT : ZEN164V130A24LS PolyZen Polymer Enhanced Zener Diode DOCUMENT: SCD27330 Micro-Assemblies REV LETTER: D REV DATE: JULY 26, 2016 PAGE NO.: 1 OF 10 Specification Status: Released GENERAL DESCRIPTION BENEFITS Littelfuse PolyZen devices are polymer  Stable Zener diode helps shield enhanced, precision Zener diode micro- downstream electronics from assemblies. They offer resettable overvoltage and reverse bias protection against multi-Watt fault  Trip events shut out overvoltage and events without the need for multi-Watt reverse bias sources heat sinks.  Analog nature of trip events minimizes The Zener diode used for voltage upstream inductive spikes clamping in a PolyZen micro-assembly was selected due to its relatively flat voltage vs current  Minimal power dissipation requirements response. This helps improve output voltage clamping,  Single component placement even when input voltage is high and diode currents are FEATURES large.  Overvoltage transient suppression An advanced feature of the PolyZen micro-assembly is that  Stable V vs fault current the Zener diode is thermally coupled to a resistively non- Z linear, polymer PTC (positive temperature coefficient) layer.  Time delayed, overvoltage trip This PTC layer is fully integrated into the device, and is  Time delayed, reverse bias trip electrically in series between V and the diode clamped IN  Multi-Watt power handling capability V . OUT  Integrated device construction This advanced PTC layer responds to either extended  RoHS Compliant diode heating or overcurrent events by transitioning from a low to high resistance state, also known as ”tripping”. A TARGET APPLICATIONS tripped PTC will limit current and generate voltage drop. It  DC power port protection in portable helps to protect both the Zener diode and the follow on electronics electronics and effectively increases the diode’s power  DC power port protection for systems handling capability. using barrel jacks for power input The polymer enhanced Zener diode helps protect sensitive  Internal overvoltage & transient portable electronics from damage caused by inductive suppression voltage spikes, voltage transients, incorrect power supplies  DC output voltage regulation and reverse bias. These devices are particularly suitable for portable electronics and other low-power DC devices. TYPICAL APPLICATION BLOCK DIAGRAM PPPooowwweeerrr SSSuuupppppplllyyy PPPooolllyyyZZZeeennn PPPrrrooottteeecccttteeeddd EEEllleeeccctttrrrooonnniiicccsss (((EEExxxttteeerrrnnnaaalll ooorrr IIInnnttteeerrrnnnaaalll))) GGGNNNDDD 222 VVVIIINNN 111 PPoollyyZZeenn +++ DDeevviiccee VVV OOOUUUTTT 333 RRReeeggguuulllaaattteeeddd RRR LLLoooaaaddd OOOuuutttpppuuuttt PPPrrrooottteeecccttteeeddd dddooowwwnnnssstttrrreeeaaammm eeellleeeccctttrrrooonnniiicccsss © 2016 Littelfuse,Inc. littelfuse.com Specifications are subject to change without notice. Revised July 26,2016

PRODUCT : ZEN164V130A24LS PolyZen Polymer Enhanced Zener Diode DOCUMENT: SCD27330 Micro-Assemblies REV LETTER: D REV DATE: JULY 26, 2016 PAGE NO.: 2 OF 10 CONFIGURATION INFORMATION Pin Configuration (Top View) Recommended Pad Dimensions 00..9944 mmmm 2 GND ((00..003377””)) 22..2211 mmmm 00..3333 mmmm VIN 1 ((00..008877””)) ((00..001133 ””)) 00..9944 mmmm 3 V ((00..003377””)) OUT 00..5566 mmmm 22..8888 mmmm 00..5566 mmmm ((00..002222””)) ((00..11113355””)) ((00..002222””)) PIN DESCRIPTION Pin Number Pin Name Pin Function 1 V V . Protected input to Zener diode. IN IN 2 GND GND 3 V V . Zener regulated voltage output OUT OUT BLOCK DIAGRAM PPoollyymmeerr PPTTCC VV IINN VV OOUUTT ZZeenneerr DDiiooddee GGNNDD DEFINITION of TERMS II II PPTTCC OOUUTT I Current flowing through the PTC portion of the PTC circuit VV IFLT RMS fault current flowing through the diode IINN I Current flowing out the V pin of the device OUT OUT Trip Event A condition where the PTC transitions to a high VV OOUUTT resistance state, thereby significantly limiting I II PTC FFLLTT and related currents, and significantly increasing the voltage drop between V and V . IN OUT Trip Time the PTC portion of the device remains both Endurance powered and in a tripped state. GGNNDD © 2016 Littelfuse,Inc. littelfuse.com Specifications are subject to change without notice. Revised July 26,2016

PRODUCT : ZEN164V130A24LS PolyZen Polymer Enhanced Zener Diode DOCUMENT: SCD27330 Micro-Assemblies REV LETTER: D REV DATE: JULY 26, 2016 PAGE NO.: 3 OF 10 GENERAL SPECIFICATIONS Operating Temperature -40º to +85ºC Storage Temperature -40º to +85ºC ELECTRICAL CHARACTERISTICS1-3, 11 (Typical unless otherwise specified) V(VZ )4 I 5 Leakage Current VInt( VM )a x8 IFLT Max9 TDriipspseiMpdaa xPti oo nw 1e 0 r I 4 HOLD R Typ6 R 7 (Azt) @2(A0º)C Max (Ohms) (Oh1Mmaxs) MVIaNxT Test IFLT Test Value Test Test Current Max Voltage Voltage Min Typ Max Current (V) (W) Voltage (A) (A) (V) (V) (mA) +1.25 +24 16.1 16.4 16.6 0.1 1.3 16 5 0.12 0.16 24V 3A 1.0 24 -40 -16V Note 1: Electrical characteristics determined at 25ºC unless otherwise specified. Note 2: This device is intended for limited fault protection. Repeated trip events or extended trip endurance can degrade the device and may affect performance to specifications. Performance impact will depend on multiple factors including, but not limited to, voltage, trip current, trip duration, trip cycles, and circuit design. For details or ratings specific to your application contact Littelfuse Circuit Protection directly. Note 3: Specifications developed using 1.0 ounce 0.045” wide copper traces on dedicated FR4 test boards. Performance in your application may vary. Note 4: Izt is the current at which Vz is measured (VZ = VOUT). Additional VZ values are available on request. Note 5: IHOLD : Maximum steady state IPTC (current entering or exiting the VIN pin of the device) that will not generate a trip event at the specified temperature. Specification assumes IFLT (current flowing through the Zener diode) is sufficiently low so as to prevent the diode from acting as a heat source. Testing is conducted with an “open” Zener. Note 6: R Typ: Resistance between VIN and VOUT pins during normal operation at room temperature. Note 7: R1Max: The maximum resistance between VIN and VOUT pins at room temperature, one hour after 1st trip or after reflow soldering. Note 8: VINT Max: VINT Max relates to the voltage across the PPTC portion of the PolyZen device (VIN-VOUT). VINT Max is defined as the voltage (VIN-VOUT) at which typical qualification devices (98% devices, 95% confidence) survived at least 100 trip cycles and 24 hours trip endurance at the specified voltage (VIN-VOUT) and current (IPTC). VINT Max testing is conducted using a "shorted" load (VOUT = 0V). VINT Max is a survivability rating, not a performance rating. Note 9: IFLT Max: IFLT Max relates to the stead state current flowing through the diode portion of the PolyZen device in a fault condition, prior to a trip event. IFLT Max is defined as the current at which typical qualification devices (12 parts per lot from 3 lots) survived 100 test cycles. RMS fault currents above IFLT Max may permanently damage the diode portion of the PolyZen device. Testing is conducted with NO load connected to VOUT, such that IOUT = 0. “Test voltage” is defined as the voltage between VIN to GND and includes the PolyZen Diode drop. Specification is dependent on the direction of current flow through the diode. IFLT Max is a survivability rating, not a performance rating. Note 10: The power dissipated by the device when in the “tripped” state, as measured on Littelfuse test boards (see note 3). Note 11: Specifications based on limited qualification data and subject to change. © 2016 Littelfuse,Inc. littelfuse.com Specifications are subject to change without notice. Revised July 26,2016

PRODUCT : ZEN164V130A24LS PolyZen Polymer Enhanced Zener Diode DOCUMENT: SCD27330 Micro-Assemblies REV LETTER: D REV DATE: JULY 26, 2016 PAGE NO.: 4 OF 10 . MECHANICAL DIMENSIONS Min Typical Max 3.85 mm 4 mm 4.15 mm Length L (0.152”) (0.16”) (0.163") 3.85 mm 4 mm 4.15 mm Width W (0.152”) (0.16”) (0.163") 1.4mm 1.7 mm 2.0 mm Height H (0.055”) (0.067”) (0.081”) Length 3.0 mm Ld - - Diode (0.118”) Height 1.0 mm Hd - - Diode (0.039”) 0.6 mm Offset O1 - - (0.024”) 0.7 mm Offset O2 - - (0.028”) SOLDER REFLOW RECOMMENDATIONS: Classification Reflow Profiles Profile Feature Pb-Free Assembly Average Ramp-Up Rate (Tsmax to Tp) 3° C/second max. Preheat • Temperature Min (Tsmin) 150 °C • Temperature Max (Tsmax) 200 °C • Time (tsmin to tsmax) 60-180 seconds Time maintained above: • Temperature (TL) 217 °C • Time (tL) 60-150 seconds Peak/Classification Temperature (Tp) 260 °C Time within 5 °C of actual Peak Temperature (tp) 20-40 seconds Ramp-Down Rate 6 °C/second max. Time 25 °C to Peak Temperature 8 minutes max. © 2016 Littelfuse,Inc. littelfuse.com Specifications are subject to change without notice. Revised July 26,2016

PRODUCT : ZEN164V130A24LS PolyZen Polymer Enhanced Zener Diode DOCUMENT: SCD27330 Micro-Assemblies REV LETTER: D REV DATE: JULY 26, 2016 PAGE NO.: 5 OF 10 PACKAGING Packaging Tape & Reel Standard Box ZENXXXVXXXAXXLS 3,000 15,000 Reel Dimensions for PolyZen Devices A = 330 max N = 102 min W = 8.4 1 W = 11.1 2 © 2016 Littelfuse,Inc. littelfuse.com Specifications are subject to change without notice. Revised July 26,2016

PRODUCT : ZEN164V130A24LS PolyZen Polymer Enhanced Zener Diode DOCUMENT: SCD27330 Micro-Assemblies REV LETTER: D REV DATE: JULY 26, 2016 PAGE NO.: 6 OF 10 MMaattttee FFiinniisshh TThheessee AArreeaa NNmmiinn AAmmaaxx Taped Component Dimensions for PolyZen Devices © 2016 Littelfuse,Inc. littelfuse.com Specifications are subject to change without notice. Revised July 26,2016

PRODUCT : ZEN164V130A24LS PolyZen Polymer Enhanced Zener Diode DOCUMENT: SCD27330 Micro-Assemblies REV LETTER: D REV DATE: JULY 26, 2016 PAGE NO.: 7 OF 10 TYPICAL CHARACTERISTICS Typical Fault Response: ZEN164V130A24LS 24 V/1.0 A Current Limited Source (Iout=0) 24 22 20 18 Vin (V) or I (A)111246 VI FoLuTt ((VA)) V) 10 V ( 8 6 4 2 0 0.00 0.05 0.10 0.15 0.20 0.25 0.30 0.35 0.40 0.45 0.50 Time (sec) Pulse IV (100uSec Pulse) Pulse IV (100uSec Pulse) 18 10 ) V (T 17 A) 5 OU (T ge: V 16 nt: IFL 0 a e Volt 15 ZEN164VxxxAxxLS Curr -5 ZEN164VxxxAxxLS 14 0 0 0 0 0 1 -10 .0 .0 .0 .0 .1 0 0 0 1 -5 0 5 10 15 20 0 0 1 01 1 Current: IFLT (A) Voltage: VOUT (V) © 2016 Littelfuse,Inc. littelfuse.com Specifications are subject to change without notice. Revised July 26,2016

PRODUCT : ZEN164V130A24LS PolyZen Polymer Enhanced Zener Diode DOCUMENT: SCD27330 Micro-Assemblies REV LETTER: D REV DATE: JULY 26, 2016 PAGE NO.: 8 OF 10 V Peak Vs I RMS (I = 0) Time to Trip Vs I RMS (I = 0) OUT FLT OUT FLT OUT 22.0 10.00 ) ZEN164V130A24LS 20.0 c e V) S ( 18.0 p ( eak 16.0 Tri 1.00 P o T T U 14.0 e O m V 12.0 Ti ZEN164V130A24LS 10.0 0.10 0.0 0.5 1.0 0.0 0.5 1.0 IFLT RMS(A) IFLT RMS (A) VOUT Peak Vs IFLT (IOUT = 0) Time to Trip Vs IFLT (IOUT = 0) 0 1 ZENxxxV130A24LS ZENxxxV130A24LS -0.2 c) e S -0.4 ( 0.1 V) p ( ri T -0.6 T VOU -0.8 e To 0.01 m -1 Ti -1.2 0.001 -50 -40 -30 -20 -10 0 -50 -40 -30 -20 -10 0 I RMS(A) I RMS (A) FLT FLT Temperature Effect on I (I = 0) Time to Trip Vs I RMS (I = 0) Hold FLT PTC FLT 2.50 10 ZENxxxV130A24LS ) ZENxxxV130A24LS 2.00 ec 1 S Linear ( (A)Hold 11..0500 (ZENxxxV130A24LS) To Trip 0.1 I e m 0.01 0.50 Ti 0.00 0.001 -40 -20 0 20 40 60 80 100 0 10 20 30 40 Ambient Temperature (C) I RMS (A) PTC © 2016 Littelfuse,Inc. littelfuse.com Specifications are subject to change without notice. Revised July 26,2016

PRODUCT : ZEN164V130A24LS PolyZen Polymer Enhanced Zener Diode DOCUMENT: SCD27330 Micro-Assemblies REV LETTER: D REV DATE: JULY 26, 2016 PAGE NO.: 9 OF 10 Temperature Effect on R Typ 0.40 ZENxxxV130A24LS ) 0.30 s m h O 0.20 ( p y T R 0.10 0.00 20 40 60 80 Ambient Temperature (C) Materials Information ROHS Compliant ELV Compliant Pb-Free Halogen Free* HF * Halogen Free refers to: Br≤900ppm, Cl≤900ppm, Br+Cl≤1500ppm. Littelfuse products are not designed for, and shall not be used for, any purpose (including, without limitation, automotive, military, aerospace, medical, life-saving, life-sustaining or nuclear facility applications, devices intended for surgical implant into the body, or any other application in which the failure or lack of desired operation of the product may result in personal injury, death, or property damage) other than those expressly set forth in applicable Littelfuse product documentation. Warranties granted by Littelfuse shall be deemed void for products used for any purpose not expressly set forth in applicable Littelfuse documentation. Littelfuse shall not be liable for any claims or damages arising out of products used in applications not expressly intended by Littelfuse as set forth in applicable Littelfuse documentation. The sale and use of Littelfuse products is subject to Littlefuse Terms and Conditions of Sale, unless otherwise agreed by Littelfuse © 2016 Littelfuse,Inc. littelfuse.com Specifications are subject to change without notice. Revised July 26,2016