Automotive Relays PCB Single Relays Power Relay K (Sealed) (cid:374) Limiting continuous current 45A (cid:374) Wide voltage range Typical applications ABS control, blower fans, car alarm, cooling fan, engine control, fuel pump, hazard warning signal, heated front screen, heated rear screen, ignition, lamps front/rear/fog light, interior lights, main switch/supply relay, seat control, seatbelt pretensioner, sun roof, turn signal, valves, window lifter, F076_fcw2b wiper control. Contact Data Coil Data Typical applications Resistive/inductive Headlights Rated coil voltage 12VDC loads capacitive loads Contact arrangement 1 form C, 1 CO Coil versions, DC coil Rated voltage 12VDC 12VDC Coil Rated Operate Release Coil Rated coil A/B (NO/NC) code voltage voltage voltage resistance power Rated current 45/30A 40/25A VDC VDC VDC Ω±10% W Limiting continuous current1) 001 12 6.9 1.2 90 1.6 23°C 45/30A 40/25A All figures are given for coil without pre-energization, at ambient temperature +23°C. 85°C 30/25A 25/20A Other coils on request. Limiting making current2) 100/30A 180/60A Limiting breaking current3) 60/30A 60/30A Insulation Data Contact material AgNi0.15 SgSnO2 Initial dielectric strength Min. recommended contact load 1A at 5VDC4) between open contacts 500VACrms Initial voltage drop, at 10A, typ./max. 20/300mV between contact and coil 500VACrms Operate/release time typ. 5/3ms5) Electrical endurance >2x105 ops. >105 ops. at 13.5VDC, 40A up to 4x60W Other Data Mechanical endurance, DC coil >107 ops. EU RoHS/ELV compliance compliant 1) Measured on 70x70x1.5mm epoxy PCB FR4 with 35cm2 (double layer 105µm) copper Ambient temperature, DC coil -40 to +85°C6) area. Cable cross section 6mm². Boundary conditions: 180°C coil temperature; 130°C Climatic cycling with condensation, solder joint. Solder joint results above 130°C on request. The load circuit shall withstand EN ISO 6988 3 cycles, storage 8/16h current applied on 40A MAXI fuse. Temperature cycling (shock), 2) The values apply to a resistive or inductive load with suitable spark suppression and at maximum 13.5VDC load voltages. IEC 60068-2-14, Na 20 cycles, -40/+85°C (dwell time 1h) 3) For a load current duration of maximum 3s for a make/break ratio of 1:10. Damp heat cyclic, 4) See chapter Diagnostics of Relays in our Application Notes or consult the internet at IEC 60068-2-30, Db, Variant 1 6 cycles, upper air temperature 55°C http://relays.te.com/appnotes/ 5) For unsuppressed relay coil. A low resistive suppression device in parallel to the relay coil increases the release time and reduces the lifetime caused by increased erosion and/or higher risk of contact tack welding. Max. DC load breaking capacity Coil operating range TE0556-E TE0555-6 Load limit curve 1: arc extinguishes, during transit time (changeover contact). Does not take into account the temperature rise due to the contact current Load limit curve 2: safe shutdown, no stationary arc (make contact). E = pre-energization Load limit curves measured with low inductive resistors verified for 1000 switching events. 1 06-2016, Rev. 0616 Catalog and product specification according Catalog and product data is subject to the Catalog product data, ‘Definitions’ section, www.te.com to IEC 61810-1 and to be used only together terms of the disclaimer and all chapters of application notes and all specifications are © 2016 TE Connectivity. with the ‘Definitions’ section. the ‘Definitions’ section, available at subject to change. http://relays.te.com/definitions

Automotive Relays PCB Single Relays Power Relay K (Sealed) (Continued) Terminal Assignment Other Data (continued) Bottom view on solder pins Damp heat constant, 56 days, upper air temperature 55°C IEC 60068-2-3, method Ca RT III – immersion cleanable version 1 form C, 1 CO Corrosive gas, IEC 60068-2-42 10 days IEC 60068-2-43 10 days Vibration resistance (functional), IEC 60068-2-6 (sine pulse form), acceleration, acc. to position 10 to 200Hz, 20 to 40g7) Shock resistance (functional), IEC 60068-2-27 (half sine form single pulses), acceleration, acc. to position 8ms 30g7) TE1086-A1 Terminal type PCB Weight sealed version approx. 22g (0.77oz) open version approx. 19g (0.67oz) Solderability (aging 3: 4h/155°C) for leaded process (Tm = 183°C), for Pb-free process (Tm = 217°C), IEC 60068-2-20 Ta, method 1, hot dip 5s, 215°C Storage conditions according IEC 600688 8) Packaging unit sealed version 525 pcs. 6) See coil operating range DC. 7) No change in the switching state >10μs. 8) For general storage and processing recommendations please refer to our Application Notes and especially to Storage in the Definitions or at http://relays.te.com/appnotes/ Mounting Hole Layout Dimensions Bottom view on solder pins 26.1 ±0.4 8.5 ±0.2 21.1 ±0.4 16.0 ±0.3 10.2 ±0.2 6.0 ±0.2 Assembly and 3.4 ±0.1 positioning aid ø 1.3 +0.1 3.4 ±0.1 3.4 ±0.6 ø 2.3 +0.1 6.6 ±0.3 2.2 ±0.1 21.2 ±0.3 12.1 ±0.1 3.3 ±0.1 ø 2.1 +0.1 2.5 – 3.0 3.0 ±0.5*) ø 2.3 +0.1 ø 2.3 +0.1 0.55 ±0.25 2.3 ±0.2 Terminals tinned *)Additional tin tops 13.3 ±0.2 max. 1.5mm TE0580-X2 2 06-2016, Rev. 0616 Catalog and product specification according Catalog and product data is subject to the Catalog product data, ‘Definitions’ section, www.te.com to IEC 61810-1 and to be used only together terms of the disclaimer and all chapters of application notes and all specifications are © 2016 TE Connectivity. with the ‘Definitions’ section. the ‘Definitions’ section, available at subject to change. http://relays.te.com/definitions

Automotive Relays PCB Single Relays Power Relay K (Sealed) (Continued) Product code structure Typical product code V23076 -A 1 001 -C 13 3 Type V23076 Power Relay K, sealed Terminal A PCB Design 1 Single relay Coil 001 12VDC Contact type C Single contact D Single contact Contact material 13 AgNi0.15 14 AgSnO 2 Contact arrangement 3 1 form C, 1 CO Product code Terminal/Encl. Design Coil Contact Contact mat. Arrangement Part number V23076-A1001-C133 PCB, sealed Single relay 12VDC Single AgNi0.15 1 form C, CO 1393277-4 V23076-A1001-D143 AgSnO2 1393277-6 3 06-2016, Rev. 0616 Catalog and product specification according Catalog and product data is subject to the Catalog product data, ‘Definitions’ section, www.te.com to IEC 61810-1 and to be used only together terms of the disclaimer and all chapters of application notes and all specifications are © 2016 TE Connectivity. with the ‘Definitions’ section. the ‘Definitions’ section, available at subject to change. http://relays.te.com/definitions

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: T E Connectivity: V23076A3001C132