Inductors for Power Circuits Radial lead TSL series Type: TSL0709 TSL0808 TSL1112 TSL1315 Issue date: September 2011 • All specifications are subject to change without notice. (cid:127) Conformity to RoHS Directive: This means that, in conformity with EU Directive 2002/95/EC, lead, cadmium, mercury, hexavalent chromium, and specific bromine-based flame retardants, PBB and PBDE, have not been used, except for exempted applications.

I N D U C T O R S REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 30°C, Humidity: 10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150°C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/Aviation equipment (8) Public information-processing equipment (2) Transportation equipment (cars, electric trains, ships, etc.) (9) Military equipment (3) Medical equipment (10) Electric heating apparatus, burning equipment (4) Power-generation control equipment (11) Disaster prevention/crime prevention equipment (5) Atomic energy-related equipment (12) Safety equipment (6) Seabed equipment (13) Other applications that are not considered general-purpose (7) Transportation control equipment applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment.

(1/8) Inductors for Power Circuits Conformity to RoHS Directive Radial Lead TSL Series TSL0709 FEATURES PRODUCT IDENTIFICATION (cid:127) The TSL series feature low DC resistance and high current han- TSL 0709 RA- 1R0 M 5R0 - PF dling capacities, making them ideal for power supply line appli- (1) (2) (3) (4) (5) (6) (7) cations. (cid:127) These parts are manufactured to a high degree of dimensional (1)Series name accuracy using non-flammable material (UL94V-0). (cid:127) Available in tape packaging to support automated mounting (2)Dimensions machines. 0709 ø7.7×9.5mm (lead pitch 5mm) (cid:127) It is a product conforming to RoHS directive. (3)Packaging style APPLICATIONS RA Taping(Ammo-pack) Televisions, VCRs, personal computers, and other electronic S Bulk equipment. (4)Inductance value SPECIFICATIONS 1R0 1µH 100 10µH –40 to +85°C Operating temperature range [Including self-temperature rise] Storage temperature range –40 to +85°C[Unit of products] (5)Inductance tolerance Terminal tensile strength 9.8N min. K ±10% Flow soldering condition 260°C /10 seconds M ±20% (6)Rated current 5R0 5A R66 0.66A (7)Lead-free compatible product PF Lead-free compatible product PACKAGING STYLE AND QUANTITIES Packaging style Quantity Taping 1000 pieces/box (Ammo-pack) Bulk 500 pieces/10tray (cid:127) Conformity to RoHS Directive: This means that, in conformity with EU Directive 2002/95/EC, lead, cadmium, mercury, hexavalent chromium, and specific bromine-based flame retardants, PBB and PBDE, have not been used, except for exempted applications. (cid:127) All specifications are subject to change without notice. 001-02 / 20110925 / e532_tsl

(2/8) SHAPES AND DIMENSIONS 3 0. ± 7 7. ø 1 0. ± 5 9. ø0.65±0.05 1 ± 5 Weight: 1.1g 5+2, –1 Dimensions in mm ELECTRICAL CHARACTERISTICS Test Self-resonant DC Rated current(A)∗1max. Inductance Inductance Q min. frequency frequency resistance Based on inductance Based on Part No. (µH) tolerance L/Q (Hz) (MHz)min. (Ω)max. change temperature rise 1 ±20% 10 1k/7.96M 70 0.006 6.6 5 TSL0709 ∗2-1R0M5R0-PF 1.5 ±20% 10 1k/7.96M 56 0.008 5.4 4.3 TSL0709 -1R5M4R3-PF 2.2 ±20% 10 1k/7.96M 45 0.011 4 3.7 TSL0709 -2R2M3R7-PF 3.3 ±20% 10 1k/7.96M 36 0.018 3.6 2.9 TSL0709 -3R3M2R9-PF 4.7 ±20% 10 1k/7.96M 29 0.022 3.1 2.6 TSL0709 -4R7M2R6-PF 6.8 ±20% 10 1k/7.96M 24 0.028 2.5 2.3 TSL0709 -6R8M2R3-PF 10 ±10% 20 1k/2.52M 19 0.043 2.1 1.9 TSL0709 -100K1R9-PF 15 ±10% 20 1k/2.52M 15 0.056 1.7 1.6 TSL0709 -150K1R6-PF 22 ±10% 20 1k/2.52M 12 0.086 1.4 1.3 TSL0709 -220K1R3-PF 33 ±10% 20 1k/2.52M 9.4 0.14 1.1 1 TSL0709 -330K1R0-PF 47 ±10% 20 1k/2.52M 7.6 0.17 0.96 0.94 TSL0709 -470KR94-PF 68 ±10% 20 1k/2.52M 6.2 0.28 0.79 0.73 TSL0709 -680KR73-PF 100 ±10% 20 1k/796k 5 0.33 0.66 0.67 TSL0709 -101KR66-PF 150 ±10% 20 1k/796k 4 0.56 0.53 0.52 TSL0709 -151KR52-PF 220 ±10% 20 1k/796k 3.2 0.72 0.44 0.46 TSL0709 -221KR44-PF 330 ±10% 20 1k/796k 2.5 1.1 0.36 0.37 TSL0709 -331KR36-PF 470 ±10% 20 1k/796k 2 1.7 0.3 0.3 TSL0709 -471KR30-PF 680 ±10% 20 1k/796k 1.7 2.3 0.25 0.26 TSL0709 -681KR25-PF 1000 ±10% 70 1k/252k 1.3 4.3 0.2 0.19 TSL0709 -102KR19-PF 1500 ±10% 50 1k/252k 1.3 5 0.17 0.16 TSL0709 -152KR16-PF ∗1Rated current: Value obtained when current flows and the temperature has risen to 25°C or when DC current flows and the initial value of inductance has fallen by 20%, whichever is smaller. ∗2 : Please specify packaging style, S(Bulk) or RA(Taping). TYPICAL ELECTRICAL CHARACTERISTICS INDUCTANCE CHANGE vs. DC SUPERPOSITION CHARACTERISTICS Test circuit L=0.1HC=20000µF 103000000 DC AYSHpePc mimoednel-4275A Universalbridge 1000µH or equivalent 1000 330µH 300 )H 100µH µ100 (e nc 33µH ucta 30 nd 10µH I 10 3.3µH 3 1µH 1 0.3 0.1 0.01 0.03 0.1 0.3 1 3 10 DC current(A) (cid:127) All specifications are subject to change without notice. 001-02 / 20110925 / e532_tsl

(3/8) Inductors for Power Circuits Conformity to RoHS Directive Radial Lead TSL Series TSL0808 FEATURES PRODUCT IDENTIFICATION (cid:127) The TSL series feature low DC resistance and high current han- TSL 0808 RA- 3R3 M 3R8 - PF dling capacities, making them ideal for power supply line appli- (1) (2) (3) (4) (5) (6) (7) cations. (cid:127) These parts are manufactured to a high degree of dimensional (1)Series name accuracy using non-flammable material (UL94V-0). (cid:127) Available in tape packaging to support automated mounting (2)Dimensions machines. 0808 ø8.5×8.3mm (lead pitch 5mm) (cid:127) It is a product conforming to RoHS directive. (3)Packaging style APPLICATIONS RA Taping(Ammo-pack) Televisions, VCRs, personal computers, and other electronic S Bulk equipment. (4)Inductance value SPECIFICATIONS 3R3 3.3µH 100 10µH –40 to +85°C Operating temperature range [Including self-temperature rise] Storage temperature range –40 to +85°C[Unit of products] (5)Inductance tolerance Terminal tensile strength 9.8N min. K ±10% Flow soldering condition 260°C /10 seconds M ±20% (6)Rated current 3R8 3.8A R67 0.67A (7)Lead-free compatible product PF Lead-free compatible product PACKAGING STYLE AND QUANTITIES Packaging style Quantity Taping 1000 pieces/box (Ammo-pack) Bulk 500 pieces/10tray (cid:127) Conformity to RoHS Directive: This means that, in conformity with EU Directive 2002/95/EC, lead, cadmium, mercury, hexavalent chromium, and specific bromine-based flame retardants, PBB and PBDE, have not been used, except for exempted applications. (cid:127) All specifications are subject to change without notice. 001-02 / 20110925 / e532_tsl

(4/8) SHAPES AND DIMENSIONS 3 0. ± 5 8. ø 5 0. ± 3 ø0.62±0.05 ±18. Weight: 1.5g 5 5+0.8, –0.5 Dimensions in mm ELECTRICAL CHARACTERISTICS Test Self-resonant DC Rated current (A)∗1max. Inductance Inductance Q frequency frequency resistance Based on inductance Based on Part No. (µH) tolerance min. L/Q (Hz) (MHz)min. (Ω)max. change temperature rise 2.2 ±20% 10 1k/7.96M 45 0.015 5.6 3.9 TSL0808 ∗2-2R2M3R9-PF 3.3 ±20% 10 1k/7.96M 34 0.017 4.5 3.8 TSL0808 -3R3M3R8-PF 4.7 ±20% 10 1k/7.96M 27 0.021 3.8 3.5 TSL0808 -4R7M3R5-PF 6.8 ±20% 10 1k/7.96M 22 0.025 3.2 3.1 TSL0808 -6R8M3R1-PF 10 ±10% 20 1k/2.52M 17 0.031 2.6 2.7 TSL0808 -100K2R6-PF 15 ±10% 20 1k/2.52M 13 0.042 2.1 2.4 TSL0808 -150K2R1-PF 22 ±10% 20 1k/2.52M 10 0.07 1.7 1.9 TSL0808 -220K1R7-PF 33 ±10% 20 1k/2.52M 8 0.092 1.4 1.5 TSL0808 -330K1R4-PF 47 ±10% 20 1k/2.52M 6.5 0.13 1.2 1.3 TSL0808 -470K1R2-PF 68 ±10% 20 1k/2.52M 5.4 0.16 1 1.1 TSL0808 -680K1R0-PF 100 ±10% 20 1k/796k 4.4 0.25 0.8 0.94 TSL0808 -101KR80-PF 150 ±10% 20 1k/796k 3.6 0.4 0.67 0.73 TSL0808 -151KR67-PF 220 ±10% 15 1k/796k 2.9 0.53 0.54 0.64 TSL0808 -221KR54-PF 330 ±10% 15 1k/796k 2.4 0.78 0.45 0.52 TSL0808 -331KR45-PF 470 ±10% 15 1k/796k 2 1 0.38 0.46 TSL0808 -471KR38-PF 680 ±10% 15 1k/796k 1.6 1.5 0.32 0.37 TSL0808 -681KR32-PF 1000 ±10% 30 1k/252k 1.3 2.2 0.26 0.3 TSL0808 -102KR26-PF 1500 ±10% 30 1k/252k 1.1 3.5 0.21 0.25 TSL0808 -152KR21-PF 2200 ±10% 50 1k/252k 0.88 6.4 0.17 0.21 TSL0808 -222KR17-PF 3300 ±10% 50 1k/252k 0.71 8.5 0.14 0.16 TSL0808 -332KR14-PF 4700 ±5% 50 1k/252k 0.68 12.2 0.15 0.13 TSL0808 -472JR13-PF ∗1Rated current: Value obtained when current flows and the temperature has risen to 25°C or when DC current flows and the initial value of inductance has fallen by 10%, whichever is smaller. ∗2 : Please specify packaging style, S(Bulk) or RA(Taping). TYPICAL ELECTRICAL CHARACTERISTICS INDUCTANCE CHANGE vs. DC SUPERPOSITION CHARACTERISTICS 1000 10000 Test circuit L=0.1HC=20000µF Test circuit L=0.1HC=20000µF 300 DC ASpecimen niversalbridge 3000 DC ASpecimen niversalbridge YHP model-4275A U YHP model-4275A U or equivalent 1000µH or equivalent )H100 68µH )H1000 680µH µ(Inductance 3100 473µ3211Hµ250HµµµHHH µ(Inductance 310000 4703µ32H012µ501H0µ0µH0HµH 3 30 1 10 0.01 0.03 0.1 0.3 1 3 10 0.01 0.03 0.1 0.3 1 3 10 DC current(A) DC current(A) (cid:127) All specifications are subject to change without notice. 001-02 / 20110925 / e532_tsl

(5/8) Inductors for Power Circuits Conformity to RoHS Directive Radial Lead TSL Series TSL1112 FEATURES PRODUCT IDENTIFICATION (cid:127) The TSL series feature low DC resistance and high current han- TSL 1112 RA- 3R3 M 5R9 - PF dling capacities, making them ideal for power supply line appli- (1) (2) (3) (4) (5) (6) (7) cations. (cid:127) These parts are manufactured to a high degree of dimensional (1)Series name accuracy using non-flammable material (UL94V-0). (cid:127) Available in tape packaging to support automated mounting (2)Dimensions machines. 1112 ø11.2×12.2mm (lead pitch 5mm) (cid:127) It is a product conforming to RoHS directive. (3)Packaging style APPLICATIONS RA Taping(Ammo-pack) Televisions, VCRs, personal computers, and other electronic S Bulk equipment. (4)Inductance value SPECIFICATIONS 3R3 3.3µH 100 10µH –40 to +85°C Operating temperature range [Including self-temperature rise] Storage temperature range –40 to +85°C[Unit of products] (5)Inductance tolerance Terminal tensile strength 9.8N min. J ±5% Flow soldering condition 260°C /10 seconds K ±10% M ±20% (6)Rated current 5R9 5.9A R56 0.56A (7)Lead-free compatible product PF Lead-free compatible product PACKAGING STYLE AND QUANTITIES Packaging style Quantity Taping 500 pieces/box (Ammo-pack) Bulk 400 pieces/8tray (cid:127) Conformity to RoHS Directive: This means that, in conformity with EU Directive 2002/95/EC, lead, cadmium, mercury, hexavalent chromium, and specific bromine-based flame retardants, PBB and PBDE, have not been used, except for exempted applications. (cid:127) All specifications are subject to change without notice. 001-02 / 20110925 / e532_tsl

(6/8) SHAPES AND DIMENSIONS 3 0. ± 2 1. 1 ø 3 0. ± 2 2. ø0.65±0.05 1 1 ± 5 Weight: 3.3g 5+1, –0.5 Dimensions in mm ELECTRICAL CHARACTERISTICS Test Self-resonant DC Rated current (A)∗1max. Inductance Inductance Q frequency frequency resistance Based on inductance Based on Part No. (µH) tolerance min. L/Q (Hz) (MHz)min. (Ω)max. change temperature rise 1.0 ±20% 15 1k/7.96M 144 0.058 14 7.7 TSL1112 ∗2-1R0M7R7-PF 2.2 ±20% 15 1k/7.96M 70 0.073 10 6.7 TSL1112 -2R2M6R7-PF 3.3 ±20% 10 1k/7.96M 36 0.01 8.8 5.9 TSL1112 -3R3M5R9-PF 4.7 ±20% 10 1k/7.96M 28 0.015 7.2 4.8 TSL1112 -4R7M4R8-PF 6.8 ±20% 10 1k/7.96M 18 0.016 6.1 4.6 TSL1112 -6R8M4R6-PF 10 ±20% 20 1k/2.52M 16 0.025 5 3.7 TSL1112 -100M3R7-PF 15 ±20% 20 1k/2.52M 12 0.029 4.2 3.4 TSL1112 -150M3R4-PF 22 ±10% 20 1k/2.52M 9.5 0.04 3.4 2.9 TSL1112 -220K2R9-PF 33 ±10% 30 1k/2.52M 7 0.062 2.8 2.3 TSL1112 -330K2R3-PF 47 ±10% 30 1k/2.52M 5.8 0.075 2.3 2.1 TSL1112 -470K2R1-PF 68 ±10% 20 1k/2.52M 4.7 0.13 1.9 1.6 TSL1112 -680K1R6-PF 100 ±10% 20 1k/796k 3.8 0.16 1.6 1.4 TSL1112 -101K1R4-PF 150 ±10% 20 1k/796k 3.1 0.26 1.3 1.1 TSL1112 -151K1R1-PF 220 ±10% 20 1k/796k 2.5 0.33 1.1 1 TSL1112 -221K1R0-PF 330 ±10% 20 1k/796k 2 0.52 0.88 0.82 TSL1112 -331KR82-PF 470 ±10% 10 1k/796k 1.6 0.66 0.75 0.72 TSL1112 -471KR72-PF 680 ±10% 10 1k/796k 1.3 1.1 0.61 0.56 TSL1112 -681KR56-PF 1000 ±5% 20 1k/252k 1.1 1.4 0.51 0.5 TSL1112 -102JR50-PF 1500 ±5% 30 1k/252k 0.82 2.4 0.43 0.38 TSL1112 -152JR38-PF 2200 ±5% 20 1k/252k 0.76 3.2 0.35 0.33 TSL1112 -222JR33-PF 3300 ±5% 30 1k/252k 0.64 4.9 0.28 0.26 TSL1112 -332JR26-PF 4700 ±5% 30 1k/252k 0.54 7.6 0.24 0.21 TSL1112 -472JR21-PF 6800 ±5% 30 1k/252k 0.45 9.8 0.2 0.18 TSL1112 -682JR18-PF 10000 ±5% 30 1k/79.6k 0.38 18 0.17 0.14 TSL1112 -103JR14-PF 15000 ±5% 50 1k/79.6k 0.29 24 0.13 0.12 TSL1112 -153JR12-PF ∗1Rated current: Value obtained when current flows and the temperature has risen to 25°C or when DC current flows and the initial value of inductance has fallen by 10%, whichever is smaller. ∗2 : Please specify packaging style, S(Bulk) or RA(Taping). TYPICAL ELECTRICAL CHARACTERISTICS INDUCTANCE CHANGE vs. DC SUPERPOSITION CHARACTERISTICS 10000 10000µH Test ciUrcnCuiv=ite2r0s0a0l 0bµriFdge L=0.1H 3300µH A 3000 DC Specimen 1000µH YHP model-4255A 1000 or equivalent µ)H300 330µH (e ctanc100 100µH u d In 33µH 30 10µH 10 3.3µH 3 1 0.01 0.03 0.1 0.3 1 3 10 DC current(A) (cid:127) All specifications are subject to change without notice. 001-02 / 20110925 / e532_tsl

(7/8) Inductors for Power Circuits Conformity to RoHS Directive Radial Lead TSL Series TSL1315 FEATURES PRODUCT IDENTIFICATION (cid:127) The TSL series feature low DC resistance and high current han- TSL 1315 RA- 100 K 5R1 - PF dling capacities, making them ideal for power supply line appli- (1) (2) (3) (4) (5) (6) (7) cations. (cid:127) These parts are manufactured to a high degree of dimensional (1)Series name accuracy using non-flammable material (UL94V-0). (cid:127) Available in tape packaging to support automated mounting (2)Dimensions machines. 1315 ø14×17mm (lead pitch 7.5mm) (cid:127) It is a product conforming to RoHS directive. (3)Packaging style APPLICATIONS RA Taping(Ammo-pack) Televisions, VCRs, personal computers, and other electronic S Bulk equipment. (4)Inductance value SPECIFICATIONS 100 10µH 102 1000µH –40 to +85°C Operating temperature range [Including self-temperature rise] Storage temperature range –40 to +85°C[Unit of products] (5)Inductance tolerance Terminal tensile strength 9.8N min. J ±5% Flow soldering condition 260°C /10 seconds K ±10% (6)Rated current 5R1 5.1A R99 0.99A (7)Lead-free compatible product PF Lead-free compatible product PACKAGING STYLE AND QUANTITIES Packaging style Quantity Taping 200 pieces/box (Ammo-pack) Bulk 50 pieces/pack (cid:127) Conformity to RoHS Directive: This means that, in conformity with EU Directive 2002/95/EC, lead, cadmium, mercury, hexavalent chromium, and specific bromine-based flame retardants, PBB and PBDE, have not been used, except for exempted applications. (cid:127) All specifications are subject to change without notice. 001-02 / 20110925 / e532_tsl

(8/8) SHAPES AND DIMENSIONS x. a m 4 1 ø x. a m 7 ø0.8±0.05 51 0. Weight: 7.5g 7.5±0.5 ±5 Dimensions in mm ELECTRICAL CHARACTERISTICS Test Self-resonant DC Rated current (A)∗1max. Inductance Inductance Q frequency frequency resistance Based on inductance Based on Part No. (µH) tolerance typ. L/Q (Hz) (MHz)min. (Ω)max. change temperature rise 10 ±10% 70 1k/2.52M 19 0.023 12 5.1 TSL1315 ∗2-100K5R1-PF 15 ±10% 70 1k/2.52M 12 0.028 9.5 4.5 TSL1315 -150K4R5-PF 22 ±10% 60 1k/2.52M 7.6 0.035 8.2 4.2 TSL1315 -220K4R2-PF 33 ±10% 50 1k/2.52M 6.9 0.043 6.8 3.7 TSL1315 -330K3R7-PF 47 ±10% 50 1k/2.52M 5.6 0.052 5.7 3.4 TSL1315 -470K3R4-PF 68 ±10% 40 1k/2.52M 4.4 0.068 4.8 3 TSL1315 -680K3R0-PF 100 ±10% 50 1k/796k 3.3 0.097 3.9 2.5 TSL1315 -101K2R5-PF 150 ±10% 50 1k/796k 2.6 0.14 3.2 2.1 TSL1315 -151K2R1-PF 220 ±10% 40 1k/796k 2.2 0.2 2.7 1.7 TSL1315 -221K1R7-PF 330 ±10% 30 1k/796k 1.8 0.3 2.1 1.4 TSL1315 -331K1R4-PF 470 ±10% 30 1k/796k 1.5 0.43 1.8 1.1 TSL1315 -471K1R1-PF 680 ±10% 30 1k/796k 1.2 0.61 1.5 0.99 TSL1315 -681KR99-PF 1000 ±5% 30 1k/252k 1 1 1.2 0.78 TSL1315 -102JR78-PF 1500 ±5% 40 1k/252k 0.83 1.3 1 0.68 TSL1315 -152JR68-PF 2200 ±5% 40 1k/252k 0.7 2 0.83 0.55 TSL1315 -222JR55-PF 3300 ±5% 40 1k/252k 0.6 3.1 0.69 0.44 TSL1315 -332JR44-PF 4700 ±5% 40 1k/252k 0.43 4.4 0.58 0.37 TSL1315 -472JR37-PF 6800 ±5% 30 1k/252k 0.38 6.5 0.46 0.3 TSL1315 -682JR30-PF 10000 ±5% 70 1k/79.6k 0.3 10 0.4 0.24 TSL1315 -103JR24-PF ∗1Rated current: Value obtained when current flows and the temperature has risen to 25°C or when DC current flows and the initial value of inductance has fallen by 10%, whichever is smaller. ∗2 : Please specify packaging style, S(Bulk) or RA(Taping). TYPICAL ELECTRICAL CHARACTERISTICS INDUCTANCE CHANGE vs. DC SUPERPOSITION CHARACTERISTICS 100000 Test circuit L=0.1HC=20000µF A 30000 DC Specimen LCRmeter YHP model-4275A 10000 10000µH or equivalent 3300µH 3000 )H µ(e1000 1000µH nc a uct 330µH nd 300 220µH I 150µH 100µH 100 68µH 47µH 33µH 30 22µH 15µH 10 10µH 5 0.01 0.03 0.1 0.3 1 3 10 DC current(A) (cid:127) All specifications are subject to change without notice. 001-02 / 20110925 / e532_tsl