Product Sample & Technical Tools & Support & Folder Buy Documents Software Community TPS62000,TPS62001,TPS62002,TPS62003 TPS62004,TPS62005,TPS62006,TPS62007,TPS62008 SLVS294F–SEPTEMBER2000–REVISEDAUGUST2015 TPS6200x High-Efficiency Step-Down Low Power DC-DC Converter 1 Features 2 Applications • High-EfficiencySynchronousStep-Down • Low-PowerCPUsandDSPs 1 ConverterwithMorethan95%Efficiency • CellularPhones • 2-Vto5.5-VOperatingInputVoltageRange • Organizers,PDAs,andHandheldPCs • AdjustableOutputVoltageRangeFrom0.8Vto • MP-3PortableAudioPlayers V IN • DigitalCameras • FixedOutputVoltageOptionsAvailablein0.9V, • USB-BasedDSLModemsandOtherNetwork 1V,1.2V,1.5V,1.8V,1.9V,2.5V,and3.3V InterfaceCards • SynchronizabletoExternalClockSignalupto 1MHz 3 Description • Upto600mAOutputCurrent The TPS6200x devices are a family of low-noise • Pin-ProgrammableCurrentLimit synchronous step-down DC/DC converters that are ideallysuitedforsystemspoweredfroma1-cellLi-ion • HighEfficiencyOveraWideLoadCurrentRange battery or from a 2- to 3-cell NiCd, NiMH, or alkaline inPowerSaveMode battery. The TPS6200x operates typically down to an • 100%MaximumDutyCycleforLowestDropout input voltage of 1.8 V, with a specified minimum input • Low-NoiseOperationAntiringingSwitchand voltageof2V. PFM/PWMOperationMode The TPS62000 operates over a free-air temperature • InternalSoftstart range of –40°C to 85°C.The device is available in the 10-pin(DGS)microsmalloutlinepackage(VSSOP). • 50-μAQuiescentCurrent(TYP) • Availableinthe10-PinMicrosmallOutline DeviceInformation(1) Package(VSSOP) PARTNUMBER PACKAGE BODYSIZE(NOM) • EvaluationModuleAvailable TPS6200x VSSOP(10) 3.00mm×3.00mm (1) For all available packages, see the orderable addendum at theendofthedatasheet. TypicalApplicationSchematic EfficiencyvsLoadCurrent 100 90 80 tVoI =5 .25 VV 1 VIN L 9 10mH VtoO V= I0.8 V % 6700 SYNC = Low − 10mF 8 ENTPS6200xFB 5 10mF† Efficiency 4500 SYNC = High 6 10 30 ILIM PGND 20 VI= 3.6 V, 7 SYNC PG 4 PG 10 VO= 2.5 V GND FC 00.1 1 10 100 1000 3 2 IO−Load Current−mA 0.1mF †WithVO≥1.8V; Co= 10mF, VO<1.8 V; Co= 47mF 1 An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications, intellectualpropertymattersandotherimportantdisclaimers.PRODUCTIONDATA.

TPS62000,TPS62001,TPS62002,TPS62003 TPS62004,TPS62005,TPS62006,TPS62007,TPS62008 SLVS294F–SEPTEMBER2000–REVISEDAUGUST2015 www.ti.com Table of Contents 1 Features.................................................................. 1 8.4 DeviceFunctionalModes........................................10 2 Applications........................................................... 1 9 ApplicationandImplementation........................ 12 3 Description............................................................. 1 9.1 ApplicationInformation............................................12 4 RevisionHistory..................................................... 2 9.2 TypicalApplication..................................................12 9.3 SystemExamples...................................................17 5 DeviceComparisonTable..................................... 3 10 PowerSupplyRecommendations..................... 20 6 PinConfigurationandFunctions......................... 3 11 Layout................................................................... 20 7 Specifications......................................................... 4 11.1 LayoutGuidelines.................................................20 7.1 AbsoluteMaximumRatings......................................4 11.2 LayoutExample....................................................20 7.2 ESDRatings..............................................................4 12 DeviceandDocumentationSupport................. 21 7.3 RecommendedOperatingConditions.......................4 7.4 ThermalInformation..................................................4 12.1 DeviceSupport......................................................21 7.5 ElectricalCharacteristics...........................................5 12.2 CommunityResources..........................................21 7.6 TypicalCharacteristics..............................................7 12.3 RelatedLinks........................................................21 12.4 Trademarks...........................................................21 8 DetailedDescription.............................................. 8 12.5 ElectrostaticDischargeCaution............................21 8.1 Overview...................................................................8 12.6 Glossary................................................................21 8.2 FunctionalBlockDiagram.........................................9 13 Mechanical,Packaging,andOrderable 8.3 FeatureDescription...................................................9 Information........................................................... 22 4 Revision History NOTE:Pagenumbersforpreviousrevisionsmaydifferfrompagenumbersinthecurrentversion. ChangesfromRevisionE(August2008)toRevisionF Page • AddedPinConfigurationandFunctionssection,ESDRatings,FeatureDescriptionsection,DeviceFunctional Modes,ApplicationandImplementationsection,PowerSupplyRecommendationssection,Layoutsection,Device andDocumentationSupportsection,andMechanical,Packaging,andOrderableInformationsection .............................. 1 2 SubmitDocumentationFeedback Copyright©2000–2015,TexasInstrumentsIncorporated ProductFolderLinks:TPS62000 TPS62001 TPS62002 TPS62003TPS62004 TPS62005 TPS62006 TPS62007 TPS62008

TPS62000,TPS62001,TPS62002,TPS62003 TPS62004,TPS62005,TPS62006,TPS62007,TPS62008 www.ti.com SLVS294F–SEPTEMBER2000–REVISEDAUGUST2015 5 Device Comparison Table PACKAGE(1) MARKING VOLTAGEOPTIONS VSSOP DGS Adjustable TPS62000DGS AIH 0.9V TPS62001DGS AII 1V TPS62002DGS AIJ 1.2V TPS62003DGS AIK 1.5V TPS62004DGS AIL 1.8V TPS62005DGS AIM 1.9V TPS62008DGS AJI 2.5V TPS62006DGS AIN 3.3V TPS62007DGS AIO (1) ForshipmentquantitiesandadditionalpackageinformationseeMechanical,Packaging,andOrderableInformation 6 Pin Configuration and Functions DGSPackage 10-PinVSSOP TopView VIN 1 10 PGND FC 2 9 L GND 3 8 EN PG 4 7 SYNC FB 5 6 ILIM PinFunctions PIN I/O DESCRIPTION NAME NO. Enable.Alogichighenablestheconverter,logiclowforcesthedeviceintoshutdownmodereducingthe EN 8 I supplycurrenttolessthan1μA. Feedbackpinforthefixedoutputvoltageoption.Fortheadjustableversionanexternalresistivedivideris FB 5 I connectedtoFB.Theinternalvoltagedividerisdisabledfortheadjustableversion. Supplybypasspin.A0.1-μFcouplingcapacitorshouldbeconnectedascloseaspossibletothispinfor FC 2 — goodhighfrequencyinputvoltagesupplyfiltering. GND 3 — Ground Switchcurrentlimit.ConnectILIMtoGNDtosettheswitchcurrentlimittotypically600mA,orconnectthis ILIM 6 I pintoV tosetthecurrentlimittotypically1200mA. IN L 9 I/O Connecttheinductortothispin.ListheswitchpinconnectedtothedrainoftheinternalpowerMOSFETS. Powergoodcomparatoroutput.Thisisanopen-drainoutput.Apull-upresistorshouldbeconnected PG 4 O betweenPGandV .Theoutputgoesactivehighwhentheoutputvoltageisgreaterthan92%ofthe OUT nominalvalue. PGND 10 — Powerground.ConnectallpowergroundstoPGND. Inputforsynchronizationtoexternalclocksignal.Synchronizestheconverterswitchingfrequencytoan externalclocksignalwithCMOSlevel: SYNC 7 I SYNC=High:Low-noisemodeenabled,fixedfrequencyPWMoperationisforced SYNC=Low(GND):Powersavemodeenabled,PFM/PWMmodeenabled VIN 1 I Supplyvoltageinput Copyright©2000–2015,TexasInstrumentsIncorporated SubmitDocumentationFeedback 3 ProductFolderLinks:TPS62000 TPS62001 TPS62002 TPS62003TPS62004 TPS62005 TPS62006 TPS62007 TPS62008

TPS62000,TPS62001,TPS62002,TPS62003 TPS62004,TPS62005,TPS62006,TPS62007,TPS62008 SLVS294F–SEPTEMBER2000–REVISEDAUGUST2015 www.ti.com 7 Specifications 7.1 Absolute Maximum Ratings Overoperatingfree-airtemperaturerange(unlessotherwisenoted)(1) MIN MAX UNIT SupplyvoltagesonpinVINandFC(2) –0.3 6 V VoltagesonpinsEN,ILIM,SYNC,PG,FB,L(2) –0.3 V +0.3 V IN Peakswitchcurrent 1.6 A T Operatingjunctiontemperature –40 150 °C J Leadtemperature(soldering,10sec) 260 °C T Storagetemperature –65 150 °C stg (1) StressesbeyondthoselistedunderAbsoluteMaximumRatingsmaycausepermanentdamagetothedevice.Thesearestressratings only,andfunctionaloperationofthedeviceattheseoranyotherconditionsbeyondthoseindicatedunderRecommendedOperating Conditionsisnotimplied.Exposuretoabsolute-maximum-ratedconditionsforextendedperiodsmayaffectdevicereliability. (2) Allvoltagevaluesarewithrespecttonetworkgroundterminal. 7.2 ESD Ratings VALUE UNIT Humanbodymodel(HBM),perANSI/ESDA/JEDECJS-001(1) ±2000 V(ESD) Electrostaticdischarge Chargeddevicemodel(CDM),perJEDECspecificationJESD22- ±1000 V C101(2) (1) JEDECdocumentJEP155statesthat500-VHBMallowssafemanufacturingwithastandardESDcontrolprocess. (2) JEDECdocumentJEP157statesthat250-VCDMallowssafemanufacturingwithastandardESDcontrolprocess. 7.3 Recommended Operating Conditions Overoperatingfree-airtemperaturerange(unlessotherwisenoted) MIN NOM MAX UNIT V Supplyvoltage 2 5.5 V IN V Outputvoltagerangeforadjustableoutputvoltageversion 0.8 V V OUT IN I Outputcurrentfor3-celloperation(V ≥2.5V;L=10μH,f=750kHz) 600 mA OUT IN I Outputcurrentfor2-celloperation(V ≥2V;L=10μH,f=750kHz) 200 mA OUT IN L Inductor(1)(seeNote2) 10 μH C Inputcapacitor(1) 10 μF IN C Outputcapacitor(1)(V ≥1.8V) 10 μF OUT OUT C Outputcapacitor(1)V <1.8V) 47 μF OUT OUT T Operatingambienttemperature –40 85 °C A T Operatingjunctiontemperature –40 125 °C J (1) RefertoApplicationInformationsectionforfurtherinformation. 7.4 Thermal Information TPS6200x THERMALMETRIC(1) DGS[VSSOP] UNIT 10PINS R Junction-to-ambientthermalresistance 160 °C/W θJA R Junction-to-case(top)thermalresistance 51 °C/W θJC(top) R Junction-to-boardthermalresistance 73 °C/W θJB ψ Junction-to-topcharacterizationparameter 5.0 °C/W JT ψ Junction-to-boardcharacterizationparameter 72 °C/W JB R Junction-to-case(bottom)thermalresistance N/A °C/W θJC(bot) (1) Formoreinformationabouttraditionalandnewthermalmetrics,seetheSemiconductorandICPackageThermalMetricsapplication report,SPRA953. 4 SubmitDocumentationFeedback Copyright©2000–2015,TexasInstrumentsIncorporated ProductFolderLinks:TPS62000 TPS62001 TPS62002 TPS62003TPS62004 TPS62005 TPS62006 TPS62007 TPS62008

TPS62000,TPS62001,TPS62002,TPS62003 TPS62004,TPS62005,TPS62006,TPS62007,TPS62008 www.ti.com SLVS294F–SEPTEMBER2000–REVISEDAUGUST2015 7.5 Electrical Characteristics Overrecommendedoperatingfree-airtemperaturerange,V =3.6V,V =2.5V,I =300mA,EN=V ,ILIM=V ,T = IN OUT OUT IN IN A –40°Cto85°C(unlessotherwisenoted) PARAMETER TESTCONDITIONS MIN TYP MAX UNIT SUPPLYCURRENT I =0mAto600mA 2.5 5.5 OUT V Inputvoltagerange V IN I =0mAto200mA 2 5.5 OUT I Operatingquiescentcurrent I =0mA,SYNC=GND(PFM-mode 50 75 μA (Q) OUT enabled) I Shutdowncurrent EN=GND 0.1 1 μA (SD) ENABLE V ENhigh-levelinputvoltage 1.3 V IH V ENlow-levelinputvoltage 0.4 V IL I ENinputleakagecurrent EN=GNDorV 0.01 0.1 μA lkg IN V Undervoltagelockoutthreshold 1.2 1.6 1.95 V (UVLO ) POWERSWITCHANDCURRENTLIMIT V =V =3.6V,I=200mA 200 280 410 IN GS P-channelMOSFETon-resistance mΩ V =V =2V,I=200mA 480 IN GS RDS(on P-channelleakagecurrent VDS=5.5V 1 μA ) VIN=VGS=3.6V,IOUT=200mA 200 280 410 N-channelMOSFETon-resistance mΩ V =V =2V,I =200mA 500 IN GS OUT N-channelleakagecurrent V =5.5V 1 μA DS 2.5V≤V ≤5.5V,ILIM=V 800 1200 1600 IN IN I P-channelcurrentlimit mA (LIM) 2V≤V ≤5.5V,ILIM=GND 390 600 900 IN V ILIMhigh-levelinputvoltage 1.3 V IH V ILIMlow-levelinputvoltage 0.4 V IL I ILIMinputleakagecurrent ILIM=GNDorV 0.01 0.1 μA lkg IN POWERGOODOUTPUT(see (1)) V Powergoodthreshold Feedbackvoltagefalling 88% 92% 94% V (PG) V V V OUT OUT OUT Powergoodhysteresis 2.5% V V OUT V PGoutputlowvoltage V =0.8×V nominal,I =10μA 0.3 V OL (FB) OUT (sink) I PGoutputleakagecurrent V =V nominal 0.01 1 μA lkg (FB) OUT Minimumsupplyvoltageforvalidpowergood 1.2 V signal OSCILLATOR f Oscillatorfrequency 500 750 1000 kHz s f Synchronizationrange CMOS-logicclocksignalonSYNCpin 500 1000 kHz (SYNC) V SYNChighlevelinputvoltage 1.3 V IH V SYNClowlevelinputvoltage 0.4 V IL I SYNCinputleakagecurrent SYNC=GNDorV 0.01 0.1 μA lkg IN Dutycycleofexternalclocksignal 20% 60% V Adjustableoutputvoltage TPS62000 0.8 5.5 V O range V Referencevoltage TPS6200x 0.45 V ref (1) Powergoodisnotvalidforthefirst100μsafterENgoeshigh.Refertotheapplicationsectionformoreinformation. Copyright©2000–2015,TexasInstrumentsIncorporated SubmitDocumentationFeedback 5 ProductFolderLinks:TPS62000 TPS62001 TPS62002 TPS62003TPS62004 TPS62005 TPS62006 TPS62007 TPS62008

TPS62000,TPS62001,TPS62002,TPS62003 TPS62004,TPS62005,TPS62006,TPS62007,TPS62008 SLVS294F–SEPTEMBER2000–REVISEDAUGUST2015 www.ti.com Electrical Characteristics (continued) Overrecommendedoperatingfree-airtemperaturerange,V =3.6V,V =2.5V,I =300mA,EN=V ,ILIM=V ,T = IN OUT OUT IN IN A –40°Cto85°C(unlessotherwisenoted) PARAMETER TESTCONDITIONS MIN TYP MAX UNIT V =2.5Vto5.5V;0mA≤I ≤600 –3% 4% IN OUT TPS62000 mA adjustable 10mA<I ≤600mA –3% 3% OUT V =2.5Vto5.5V;0mA≤I ≤600 –3% 4% IN OUT TPS620010.9 mA V 10mA<I ≤600mA –3% 3% OUT V =2.5Vto5.5V;0mA≤I ≤600 –3% 4% TPS62002 mIAN OUT 1V 10mA<I ≤600mA –3% 3% OUT V =2.5Vto5.5V;0mA≤I ≤600 –3% 4% TPS62003 mIAN OUT 1.2V 10mA<I ≤600mA –3% 3% OUT V =2.5Vto5.5V;0mA≤I ≤600 –3% 4% V Fixedoutputvoltage TPS62004 mIAN OUT V OUT 1.5V 10mA<I ≤600mA –3% 3% OUT V =2.5Vto5.5V;0mA≤I ≤600 –3% 4% TPS62005 mIAN OUT 1.8V 10mA<I ≤600mA –3% 3% OUT V =2.5Vto5.5V;0mA≤I ≤600 –3% 4% TPS62008 mIAN OUT 1.9V 10mA<I ≤600mA –3% 3% OUT V =2.7Vto5.5V;0mA≤I ≤600 –3% 4% TPS62006 mIAN OUT 2.5V 10mA<I ≤600mA –3% 3% OUT V =3.6Vto5.5V;0mA≤I ≤600 –3% 4% TPS62007 mIAN OUT 3.3V 10mA<I ≤600mA –3% 3% OUT Lineregulation V =V +0.5V(min.2V)to5.5V, 0.05 %/V IN OUT I =10mA OUT Loadregulation V =5.5V;I =10mAto600mA 0.6% IN OUT V =5V;V =3.3V;I =300mA IN OUT OUT η Efficiency 95% V =3.6V;V =2.5V;I =200mA IN OUT OUT Start-uptime I =0mA,timefromactiveENtoV 0.4 2 ms OUT OUT 6 SubmitDocumentationFeedback Copyright©2000–2015,TexasInstrumentsIncorporated ProductFolderLinks:TPS62000 TPS62001 TPS62002 TPS62003TPS62004 TPS62005 TPS62006 TPS62007 TPS62008

TPS62000,TPS62001,TPS62002,TPS62003 TPS62004,TPS62005,TPS62006,TPS62007,TPS62008 www.ti.com SLVS294F–SEPTEMBER2000–REVISEDAUGUST2015 7.6 Typical Characteristics A m nt - e urr C nt e c s e u Q g n ati er p O - Q) I( Figure1.DropoutVoltagevsLoadCurrent Figure2.OperatingQuiescentCurrentvsInputVoltage (PowerSaveMode) A m nt - e urr C nt e c s e u Q g n ati er p O - Q) I( Figure3.OperatingQuiescentCurrentvsInputVoltage Figure4.OscillatorFrequencyvsFree-AirTemperature (ForcedPWM) Copyright©2000–2015,TexasInstrumentsIncorporated SubmitDocumentationFeedback 7 ProductFolderLinks:TPS62000 TPS62001 TPS62002 TPS62003TPS62004 TPS62005 TPS62006 TPS62007 TPS62008

TPS62000,TPS62001,TPS62002,TPS62003 TPS62004,TPS62005,TPS62006,TPS62007,TPS62008 SLVS294F–SEPTEMBER2000–REVISEDAUGUST2015 www.ti.com 8 Detailed Description 8.1 Overview The TPS6200x is a step down converter operating in a current mode PFM/PWM scheme with a typical switching frequencyof750kHz. At moderate to heavy loads, the converter operates in the pulse width modulation (PWM) and at light loads the converterentersapowersavemode(pulsefrequencymodulation,PFM)tokeeptheefficiencyhigh. In the PWM mode operation, the part operates at a fixed frequency of 750 kHz. At the beginning of each clock cycle, the high side P-channel MOSFET is turned on. The current in the inductor ramps up and is sensed via an internal circuit. The high side switch is turned off when the sensed current causes the PFM/PWM comparator to trip when the output voltage is in regulation or when the inductor current reaches the current limit (set by ILIM). After a minimum dead time preventing shoot through current, the low side N-channel MOSFET is turned on and the current ramps down again. As the clock cycle is completed, the low side switch is turned off and the next clockcyclestarts. In discontinuous conduction mode (DCM), the inductor current ramps to zero before the end of each clock cycle. In order to increase the efficiency the load comparator turns off the low side MOSFET before the inductor current becomes negative. This prevents reverse current flowing from the output capacitor through the inductor and low sideMOSFETtogroundthatwouldcauseadditionallosses. As the load current decreases and the peak inductor current does not reach the power save mode threshold of typically120mAformorethan15clockcycles,theconverterentersapulsefrequencymodulation(PFM)mode. InthePFMmode,theconverteroperateswith: • Variablefrequency • Constantpeakcurrentthatreducesswitchinglosses • Quiescentcurrentataminimum Thus maintaining the highest efficiency at light load currents. In this mode, the output voltage is monitored with the error amplifier. As soon as the output voltage falls below the nominal value, the high side switch is turned on and the inductor current ramps up. When the inductor current reaches the peak current of typical: 150 mA + 50 mA/V × (V – V ), the high side switch turns off and the low side switch turns on. As the inductor current IN OUT ramps down, the low side switch is turned off before the inductor current becomes negative which completes the cycle.Whentheoutputvoltagefallsbelowthenominalvoltageagain,thenextcycleisstarted. The converter enters the PWM mode again as soon as the output voltage can not be maintained with the typical peakinductorcurrentinthePFMmode. Thecontrolloopisinternallycompensatedreducingtheamountofexternalcomponents. Theswitchcurrentisinternallysensedandthemaximumcurrentlimitcanbesettotypical600mAbyconnecting ILIMtoground;or,totypically1.2AbyconnectingILIMtoV . IN 8 SubmitDocumentationFeedback Copyright©2000–2015,TexasInstrumentsIncorporated ProductFolderLinks:TPS62000 TPS62001 TPS62002 TPS62003TPS62004 TPS62005 TPS62006 TPS62007 TPS62008

TPS62000,TPS62001,TPS62002,TPS62003 TPS62004,TPS62005,TPS62006,TPS62007,TPS62008 www.ti.com SLVS294F–SEPTEMBER2000–REVISEDAUGUST2015 8.2 Functional Block Diagram PG FC (See Note B) VIN Undervoltage 10 W Lockout Bias Supply EN Power Good Slope Compensation Current P-Channel Sense Power MOSFET + PFM/PWM _ Mode Select PFM/PWM Error Amplifier Comparator R1 _ _ PFM/PWM Driver FB L Control Logic Shoot-Through (See + + Current Limit Logic Note A) Logic Soft Start Compensation R2 N-Channel R1 + R2 ≈ 1 MW Power MOSFET EN Sync Current Sense + Load Comparator _ Vref = 0.45 V + + Oscillator + Offset _ PGND Antiringing FB GND SYNC ILIM A. The adjustable output voltage version does not use the internal feedback resistor divider. The FB pin is directly connectedtotheerroramplifier. B. DonotconnecttheFCpintoanexternalpowersource 8.3 Feature Description 8.3.1 LowNoiseAntiringingSwitch An antiringing switch is implemented in order to reduce the EMI radiated from the converter during discontinuous conduction mode (DCM). In DCM, the inductor current ramps to zero before the end of each switching period. The internal load comparator turns off the low side switch at that instant thus preventing the current flowing backward through the inductance which increases the efficiency. An antiringing switch across the inductor preventsparasiticoscillationcausedbytheresidualenergystoredintheinductance(seeFigure11). NOTE The antiringing switch is only activated in the fixed output voltage versions. It is not enabledfortheadjustableoutputvoltageversionTPS62000. 8.3.2 Enable Logic low on EN forces the TPS6200x into shutdown. In shutdown, the power switch, drivers, voltage reference, oscillator, and all other functions are turned off. The supply current is reduced to less than 1 μA in the shutdown mode. Copyright©2000–2015,TexasInstrumentsIncorporated SubmitDocumentationFeedback 9 ProductFolderLinks:TPS62000 TPS62001 TPS62002 TPS62003TPS62004 TPS62005 TPS62006 TPS62007 TPS62008

TPS62000,TPS62001,TPS62002,TPS62003 TPS62004,TPS62005,TPS62006,TPS62007,TPS62008 SLVS294F–SEPTEMBER2000–REVISEDAUGUST2015 www.ti.com Feature Description (continued) 8.3.3 UndervoltageLockout An undervoltage lockout circuit provides the save operation of the device. It prevents the converter from turning onwhenthevoltageonV islessthantypically1.6V. IN 8.3.4 PowerGoodComparator The power good (PG) comparator has an open drain output capable of sinking typically 10 μA. The PG is only active when the device is enabled (EN = high). When the device is disabled (EN = low), the PG pin is high impedance. The PG output is only valid after a 100 μs delay after the device is enabled and the supply voltage is greater than 1.2 V. This is only important in cases where the pullup resistor of the PG pin is connected to an external voltage source which might cause an initial spike (false high signal) within the first 100 μs after the input voltage exceeds 1.2 V. This initial spike can be filtered with a small R-C filter to avoid false power good signals during start-up. If the PG pin is connected to the output of the TPS62000 with a pullup resistor, no initial spike (false high signal) occursandnoprecautionshavetobetakenduringstart-up. The PG pin becomes active high when the output voltage exceeds typically 94.5% of its nominal value. Leave thePGpinunconnectedwhennotused. 8.4 Device Functional Modes The TPS6200x is a synchronous current-mode PWM converter with integrated – and P-channel power MOSFET switches. Synchronous rectification is used to increase efficiency and to reduce external component count. To achieve the highest efficiency over a wide load current range, the converter enters a power-saving pulse- frequency modulation (PFM) mode at light load currents. Operating frequency is typically 750 kHz, allowing the use of small inductor and capacitor values. The device can be synchronized to an external clock signal in the range of 500 kHz to 1 MHz. For low-noise operation, the converter can be operated in the PWM mode and the internal antiringing switch reduces noise and EMI. In the shutdown mode, the current consumption is reduced to lessthan1 μA.TheTPS62000isavailableinthe10-pin(DGS)microsmalloutlinepackage(VSSOP).Thedevice operatesoverafree-airtemperaturerangeof –40°Cto85°C. 8.4.1 SoftStart As the enable pin (EN) goes high, the soft-start function generates an internal voltage ramp. This causes the start-up current to slowly rise preventing output voltage overshoot and high inrush currents. The soft-start duration is typical 1 ms (see Figure 12). When the soft-start function is completed, the error amplifier is connecteddirectlytotheinternalvoltagereference. 8.4.2 Synchronization,PowerSaveMode,andForcedPWMMode If no clock signal is applied, the converter operates with a typical switching frequency of 750 kHz. It is possible to synchronize the converter to an external clock within a frequency range from 500 kHz to 1000 kHz. The device automatically detects the rising edge of the first clock and is synchronized immediately to the external clock. If the clock signal is stopped, the converter automatically switches back to the internal clock and continues operation without interruption. The switch over is initiated if no rising edge on the SYNC pin is detected for a duration of four clock cycles. Therefore, the maximum delay time can be 8 μs in case the internal clock has a minimumfrequencyof500kHz. In case the device is synchronized to an external clock, the power save mode is disabled and the device stays in forcedPWMmode. Connecting the SYNC pin to the GND pin enables the power save mode. The converter operates in the PWM modeatmoderatetoheavyloadsandinthePFMmodeduringlightloadsmaintaininghighefficiencyoverawide loadcurrentrange. Connecting the SYNC pin to the VIN pin forces the converter to operate permanently in the PWM mode even at light or no load currents. The advantage is the converter operates with a fixed switching frequency that allows simple filtering of the switching frequency for noise sensitive applications. In this mode, the efficiency is lower comparedtothepowersavemodeduringlightloads(see). 10 SubmitDocumentationFeedback Copyright©2000–2015,TexasInstrumentsIncorporated ProductFolderLinks:TPS62000 TPS62001 TPS62002 TPS62003TPS62004 TPS62005 TPS62006 TPS62007 TPS62008

TPS62000,TPS62001,TPS62002,TPS62003 TPS62004,TPS62005,TPS62006,TPS62007,TPS62008 www.ti.com SLVS294F–SEPTEMBER2000–REVISEDAUGUST2015 Device Functional Modes (continued) ItispossibletoswitchfromforcedPWMmodetothepowersavemodeduringoperation. The flexible configuration of the SYNC pin during operation of the device allows efficient power management by adjustingtheoperationoftheTPS6200xtothespecificsystemrequirements. 8.4.3 100%DutyCycleOperation As the input voltage approaches the output voltage and the duty cycle exceeds typical 95%, the converter turns the P-channel high side switch continuously on. In this mode, the output voltage is equal to the input voltage minusthevoltagedropacrosstheP-channelMOSFET. 8.4.4 NoLoadOperation In case the converter operates in the forced PWM mode and there is no load connected to the output, the converterwillregulatetheoutputvoltagebyallowingtheinductorcurrenttoreverseforashortperiodoftime. Copyright©2000–2015,TexasInstrumentsIncorporated SubmitDocumentationFeedback 11 ProductFolderLinks:TPS62000 TPS62001 TPS62002 TPS62003TPS62004 TPS62005 TPS62006 TPS62007 TPS62008

TPS62000,TPS62001,TPS62002,TPS62003 TPS62004,TPS62005,TPS62006,TPS62007,TPS62008 SLVS294F–SEPTEMBER2000–REVISEDAUGUST2015 www.ti.com 9 Application and Implementation NOTE Information in the following applications sections is not part of the TI component specification, and TI does not warrant its accuracy or completeness. TI’s customers are responsible for determining suitability of components for their purposes. Customers should validateandtesttheirdesignimplementationtoconfirmsystemfunctionality. 9.1 Application Information The TPS6200x device family are highly efficient synchronous step down DC/DC converters providing adjustable outputvoltagesfrom0.9VtoV andfixedoutputvoltages. IN 9.2 Typical Application VI= 2.7 V to 5.5 V 1 VIN L 9 L1= 10mH VO= 2.5 V/600 mA R3 = 320 kΩ + 8 5 EN FB Ci= 10mF TPS62000 R1 = 820 kΩ C(ff)= 6.8 pF 6 ILIM PG 4 PG + Co= 10mF 7 10 R2 = 180 kΩ SYNC PGND GND FC 3 2 C3 = 0.1mF Figure5. TypicalApplicationCircuitforAdjustableOutputVoltageOption 9.2.1 DesignRequirements When the adjustable output voltage version (TPS62000DGS) is used, the output voltage is set by the external resistordivider(seeFigure5). Theoutputvoltageiscalculatedas: æ R1ö VO =0.45V ´ çè1+ R2÷ø (1) withR1+R2≤ 1MΩ R1+R2shouldnotbegreaterthan1MWbecauseofstabilityreasons. For stability reasons, a small bypass capacitor (C ) is required in parallel to the upper feedback resistor, refer to (ff) Figure5.Thebypasscapacitorvaluecanbecalculatedas: 1 C = forC <47mF (ff) 2p´30000´R1 o (2) 1 C = forC ³47mF (ff) 2p´5000´R1 o (3) R1 is the upper resistor of the voltage divider. For C , choose a value which comes closest to the computed (ff) result. 12 SubmitDocumentationFeedback Copyright©2000–2015,TexasInstrumentsIncorporated ProductFolderLinks:TPS62000 TPS62001 TPS62002 TPS62003TPS62004 TPS62005 TPS62006 TPS62007 TPS62008

TPS62000,TPS62001,TPS62002,TPS62003 TPS62004,TPS62005,TPS62006,TPS62007,TPS62008 www.ti.com SLVS294F–SEPTEMBER2000–REVISEDAUGUST2015 Typical Application (continued) 9.2.2 DetailedDesignProcedure 9.2.2.1 InductorSelection A 10 μH minimum output inductor is used with the TPS6200x. Values larger than 22 μH or smaller than 10 μH maycausestabilityproblemsbecauseoftheinternalcompensationoftheregulator. For output voltages greater than 1.8 V, a 22 μH inductance might be used in order to improve the efficiency of theconverter. After choosing the inductor value of typically 10 μH, two additional inductor parameters should be considered: firstthecurrentratingoftheinductorandsecondtheDCresistance. The DC resistance of the inductance influences directly the efficiency of the converter. Therefore, an inductor withlowestDCresistanceshouldbeselectedforhighestefficiency. In order to avoid saturation of the inductor, the inductor should be rated at least for the maximum output current plustheinductorripplecurrentwhichiscalculatedas: V 1 - O V DI DI =V ´ I I =I + L L O L ´ f L(max) O(max) 2 Where: • ƒ=Switchingfrequency(750kHztypical) • L=Inductorvalue • ΔI =Peak-to-peakinductorripplecurrent L • I =Maximuminductorcurrent (4) L(max) ThehighestinductorcurrentoccursatmaximumV . IN A more conservative approach is to select the inductor current rating just for the maximum switch current of the TPS6200xwhichis1.6AwithILIM=V and900mAwithILIM=GND.SeeTable1forrecommendedinductors. IN Table1.TestedInductors OUTPUTCURRENT INDUCTORVALUE COMPONENTSUPPLIER COMMENTS 0mAto600mA 10μH CoilcraftDO3316P-103 Highefficiency CoilcraftDT3316P-103 SumidaCDR63B-100 SumidaCDRH5D28-100 CoilcraftDO1608C-103 Smallestsolution SumidaCDRH4D28-100 0mAto300mA 10μH CoilcraftDO1608C-103 Highefficiency MurataLQH4C100K04 Smallestsolution 9.2.2.2 OutputCapacitorSelection For best performance, a low ESR output capacitor is needed. At output voltages greater than 1.8 V, ceramic outputcapacitorscanbeusedtoshowthebestperformance.Outputvoltagesbelow1.8Vrequirealargeroutput capacitorandESRvaluetoimprovetheperformanceandstabilityoftheconverter. Table2.CapacitorSelection OUTPUTVOLTAGERANGE OUTPUTCAPACITOR OUTPUTCAPACITORESR 1.8V≤V ≤5.5V C ≥10μF ESR≤120mΩ IN o 0.8V≤V <1.8V C ≥47μF ESR>50mΩ IN o Copyright©2000–2015,TexasInstrumentsIncorporated SubmitDocumentationFeedback 13 ProductFolderLinks:TPS62000 TPS62001 TPS62002 TPS62003TPS62004 TPS62005 TPS62006 TPS62007 TPS62008

TPS62000,TPS62001,TPS62002,TPS62003 TPS62004,TPS62005,TPS62006,TPS62007,TPS62008 SLVS294F–SEPTEMBER2000–REVISEDAUGUST2015 www.ti.com SeeTable3forrecommendedcapacitors. If an output capacitor is selected with an ESR value ≤ 120 mΩ, its RMS ripple current rating always meets the applicationrequirements.Justforcompleteness,theRMSripplecurrentiscalculatedas: V 1 - O V 1 I =V ´ I ´ RMS(CO) O L ´ f 2´ 3 (5) The overall output ripple voltage is the sum of the voltage spike caused by the output capacitor ESR plus the voltageripplecausedbycharginganddischargingtheoutputcapacitor: V 1 - O V æ 1 ö DVO =VO´ L ´ fI ´ çè8´CO´ f +ESR÷ø (6) WherethehighestoutputvoltagerippleoccursatthehighestinputvoltageV. I Table3.TestedCapacitors CAPACITORVALUE ESR/mΩ COMPONENTSUPPLIER COMMENTS 10μF 50 TaiyoYudenJMK316BJ106KL Ceramic 47μF 100 Sanyo6TPA47M POSCAP 68μF 100 Spraque594D686X0010C2T Tantalum 9.2.2.3 InputCapacitorSelection Because of the nature of the buck converter having a pulsating input current, a low ESR input capacitor is required for best input voltage filtering and minimizing the interference with other circuits caused by high input voltagespikes. Theinputcapacitorshouldhaveaminimumvalueof10μFandcanbeincreasedwithoutanylimitforbetterinput voltagefiltering. Theinputcapacitorshouldberatedforthemaximuminputripplecurrentcalculatedas: V æ V ö I =I ´ O ´ç1- O ÷ RMS O(max) VI è VI ø (7) I I = O TheworstcaseRMSripplecurrentoccursatD=0.5andiscalculatedas: RMS 2 CeramiccapacitorshowagoodperformancebecauseoftheirlowESRvalue,andtheyarelesssensitiveagainst voltagetransientscomparedtotantalumcapacitors. PlacetheinputcapacitorascloseaspossibletotheinputpinoftheICforbestperformance. 14 SubmitDocumentationFeedback Copyright©2000–2015,TexasInstrumentsIncorporated ProductFolderLinks:TPS62000 TPS62001 TPS62002 TPS62003TPS62004 TPS62005 TPS62006 TPS62007 TPS62008

TPS62000,TPS62001,TPS62002,TPS62003 TPS62004,TPS62005,TPS62006,TPS62007,TPS62008 www.ti.com SLVS294F–SEPTEMBER2000–REVISEDAUGUST2015 9.2.3 ApplicationCurves 100 VO= 2.5 V 90 80 VI= 3.6 V % − y nc 70 e ci Effi VI= 5 V 60 50 40 0.1 1 10 100 1000 IO−Load Current−mA Figure6.EfficiencyvsLoadCurrent Figure7.EfficiencyvsLoadCurrent 200ms/div Figure8.EfficiencyvsLoadCurrent Figure9.LoadTransientResponse 400ms/div 10ms/div Figure10.LineTransientResponse Figure11.PowerSaveModeOperation Copyright©2000–2015,TexasInstrumentsIncorporated SubmitDocumentationFeedback 15 ProductFolderLinks:TPS62000 TPS62001 TPS62002 TPS62003TPS62004 TPS62005 TPS62006 TPS62007 TPS62008

TPS62000,TPS62001,TPS62002,TPS62003 TPS62004,TPS62005,TPS62006,TPS62007,TPS62008 SLVS294F–SEPTEMBER2000–REVISEDAUGUST2015 www.ti.com 2.55 EN 2.54 2V/div 2.53 V − 2.52 e ag 2.51 VO olt 1 V/div ut V 2.50 p Power Good Out 2.49 1 V/div − O 2.48 V 2.47 II 2.46 200mA/div 2.45 0 100 200 300 400 500 600 250ms/div IO−Load Current−mA Figure12.Start-UpvsTime Figure13.OutputVoltagevsLoadCurrent 16 SubmitDocumentationFeedback Copyright©2000–2015,TexasInstrumentsIncorporated ProductFolderLinks:TPS62000 TPS62001 TPS62002 TPS62003TPS62004 TPS62005 TPS62006 TPS62007 TPS62008

TPS62000,TPS62001,TPS62002,TPS62003 TPS62004,TPS62005,TPS62006,TPS62007,TPS62008 www.ti.com SLVS294F–SEPTEMBER2000–REVISEDAUGUST2015 9.3 System Examples 9.3.1 Standard5-Vto3.3-V/600-mAConversion;HighEfficiency L1 22mH 1 9 VI= 5 V VIN L VO= 3.3 V/600 mA C1 8 5 EN FB 10mF C2 TPS62007DGS 680 kΩ 10mF 6 10 ILIM PGND 7 4 SYNC PG Power GND FC Good 3 2 L1: Sumdia CDRH5D28-220 C3 C1, C2:10mF Ceramic Taiyo Yuden 0.1mF JMK316BJ106KL C3: 0.1mF Ceramic Figure14. Standard5-Vto3.3-V/600-mAConversion;HighEfficiency 9.3.2 SingleLi-ionto2.5-V/600-mAUsingCeramicCapacitorsOnly L1 10mH 1 9 VI= 2.7 V to 4.2 V VIN L VO= 2.5 V/600 mA C1 8 5 EN FB 10mF C2 TPS62006DGS 470 kΩ 10mF 6 10 ILIM PGND 7 4 SYNC PG Power Good GND FC 3 2 L1: Sumdia CDRH5D28-100 C3 C1,C2: 10mF Ceramic Taiyo Yuden 0.1mF JMK316BJ106KL C3: 0.1mF Ceramic Figure15. SingleLi-ionto2.5-V/600-mAUsingCeramicCapacitorsOnly Copyright©2000–2015,TexasInstrumentsIncorporated SubmitDocumentationFeedback 17 ProductFolderLinks:TPS62000 TPS62001 TPS62002 TPS62003TPS62004 TPS62005 TPS62006 TPS62007 TPS62008

TPS62000,TPS62001,TPS62002,TPS62003 TPS62004,TPS62005,TPS62006,TPS62007,TPS62008 SLVS294F–SEPTEMBER2000–REVISEDAUGUST2015 www.ti.com System Examples (continued) 9.3.3 SingleLi-ionto1.8V/300mA;SmallestSolutionSize L1 10mH 1 9 VI= 2.5 V to 4.2 V VIN L VO= 1.8 V/300 mA C1 8 5 EN FB 10mF C2 TPS62005DGS 10mF 6 10 ILIM PGND 7 4 SYNC PG GND FC 3 2 L1: Murata LQH4C100K04 C3 C1,C2: 10mF Ceramic Taiyo Yuden 0.1mF JMK316BJ106KL C3: 0.1mF Ceramic NOTE: ForlownoiseoperationconnectSYNCtoV IN Figure16. SingleLi-ionto1.8V/300mA;SmallestSolutionSize 9.3.4 DualCellNiMHorNiCdto1.2V/200mA;SmallestSolutionSize L1 10mH 1 9 VI= 2 V to 3.8 V VIN L VO= 1.2 V/200 mA C1 8 5 10mF EN FB C2 + TPS62003 47mF 6 10 ILIM PGND 7 4 SYNC PG GND FC 3 2 L1: Murata LQH4C100K04 C3 C1: 10mF Ceramic Taiyo Yuden 0.1mF JMK316BJ106KL C2: Sanyo 6TPA47M C3: 0.1mF Ceramic Figure17. DualCellNiMHorNiCdto1.2V/200mA;SmallestSolutionSize 18 SubmitDocumentationFeedback Copyright©2000–2015,TexasInstrumentsIncorporated ProductFolderLinks:TPS62000 TPS62001 TPS62002 TPS62003TPS62004 TPS62005 TPS62006 TPS62007 TPS62008

TPS62000,TPS62001,TPS62002,TPS62003 TPS62004,TPS62005,TPS62006,TPS62007,TPS62008 www.ti.com SLVS294F–SEPTEMBER2000–REVISEDAUGUST2015 System Examples (continued) 9.3.5 DynamicOutputVoltageProgrammingAsUsedinLowPowerDSPApplications 10mH 820 kW (2) 10mF 470 kW 47mF 326 kW 524 kW 0.1mF Sumida CDRH5D28-100 10mF Ceramic TaiyoYuden JMK316BJ106KL Sanyo 6TPA47M 0.1mF Ceramic (1) UseasmallR-Cfiltertofilterwrongresetsignalsduringoutputvoltagetransitions. (2) AlargevalueisusedforC(ff)tocompensatefortheparasiticcapacitanceintroducedintotheregulationloopbyQ1. Figure18. DynamicOutputVoltageProgrammingAsUsedinLowPowerDSPApplications Copyright©2000–2015,TexasInstrumentsIncorporated SubmitDocumentationFeedback 19 ProductFolderLinks:TPS62000 TPS62001 TPS62002 TPS62003TPS62004 TPS62005 TPS62006 TPS62007 TPS62008

TPS62000,TPS62001,TPS62002,TPS62003 TPS62004,TPS62005,TPS62006,TPS62007,TPS62008 SLVS294F–SEPTEMBER2000–REVISEDAUGUST2015 www.ti.com 10 Power Supply Recommendations The TPS6200x device family has no special requirements for its input power supply. The input power supply's output current needs to be rated according to the supply voltage, output voltage and output current of the TPS6200x. 11 Layout 11.1 Layout Guidelines As for all switching power supplies, the layout is an important step in the design especially at high peak currents and switching frequencies. If the layout is not carefully done, the regulator might show stability problems as well asEMIproblems. Therefore, use wide and short traces for the main current paths as indicted in bold in Figure 19. The input capacitorshouldbeplacedascloseaspossibletotheICpinsaswellastheinductorandoutputcapacitor.Place the bypass capacitor, C3, as close as possible to the FC pin. The analog ground, GND, and the power ground, PGND, need to be separated. Use a common ground node as shown in Figure 19 to minimize the effects of groundnoise. 11.2 Layout Example L1 1 9 VI VIN L VO + 8 5 R3 EN FB Ci TPS62000 R1 C(ff) 6 4 + ILIM PG PG Co 7 10 R2 SYNC PGND GND FC C3 3 2 Figure19. LayoutDiagram 20 SubmitDocumentationFeedback Copyright©2000–2015,TexasInstrumentsIncorporated ProductFolderLinks:TPS62000 TPS62001 TPS62002 TPS62003TPS62004 TPS62005 TPS62006 TPS62007 TPS62008

TPS62000,TPS62001,TPS62002,TPS62003 TPS62004,TPS62005,TPS62006,TPS62007,TPS62008 www.ti.com SLVS294F–SEPTEMBER2000–REVISEDAUGUST2015 12 Device and Documentation Support 12.1 Device Support 12.1.1 Third-PartyProductsDisclaimer TI'S PUBLICATION OF INFORMATION REGARDING THIRD-PARTY PRODUCTS OR SERVICES DOES NOT CONSTITUTE AN ENDORSEMENT REGARDING THE SUITABILITY OF SUCH PRODUCTS OR SERVICES OR A WARRANTY, REPRESENTATION OR ENDORSEMENT OF SUCH PRODUCTS OR SERVICES, EITHER ALONEORINCOMBINATIONWITHANYTIPRODUCTORSERVICE. 12.2 Community Resources The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of Use. TIE2E™OnlineCommunity TI'sEngineer-to-Engineer(E2E)Community.Createdtofostercollaboration amongengineers.Ate2e.ti.com,youcanaskquestions,shareknowledge,exploreideasandhelp solveproblemswithfellowengineers. DesignSupport TI'sDesignSupport QuicklyfindhelpfulE2Eforumsalongwithdesignsupporttoolsand contactinformationfortechnicalsupport. 12.3 Related Links The table below lists quick access links. Categories include technical documents, support and community resources,toolsandsoftware,andquickaccesstosampleorbuy. Table4.RelatedLinks TECHNICAL TOOLS& SUPPORT& PARTS PRODUCTFOLDER SAMPLE&BUY DOCUMENTS SOFTWARE COMMUNITY TPS62000 Clickhere Clickhere Clickhere Clickhere Clickhere TPS62001 Clickhere Clickhere Clickhere Clickhere Clickhere TPS62002 Clickhere Clickhere Clickhere Clickhere Clickhere TPS62003 Clickhere Clickhere Clickhere Clickhere Clickhere TPS62004 Clickhere Clickhere Clickhere Clickhere Clickhere TPS62005 Clickhere Clickhere Clickhere Clickhere Clickhere TPS62006 Clickhere Clickhere Clickhere Clickhere Clickhere TPS62007 Clickhere Clickhere Clickhere Clickhere Clickhere TPS62008 Clickhere Clickhere Clickhere Clickhere Clickhere 12.4 Trademarks E2EisatrademarkofTexasInstruments. Allothertrademarksarethepropertyoftheirrespectiveowners. 12.5 Electrostatic Discharge Caution Thesedeviceshavelimitedbuilt-inESDprotection.Theleadsshouldbeshortedtogetherorthedeviceplacedinconductivefoam duringstorageorhandlingtopreventelectrostaticdamagetotheMOSgates. 12.6 Glossary SLYZ022—TIGlossary. Thisglossarylistsandexplainsterms,acronyms,anddefinitions. Copyright©2000–2015,TexasInstrumentsIncorporated SubmitDocumentationFeedback 21 ProductFolderLinks:TPS62000 TPS62001 TPS62002 TPS62003TPS62004 TPS62005 TPS62006 TPS62007 TPS62008

TPS62000,TPS62001,TPS62002,TPS62003 TPS62004,TPS62005,TPS62006,TPS62007,TPS62008 SLVS294F–SEPTEMBER2000–REVISEDAUGUST2015 www.ti.com 13 Mechanical, Packaging, and Orderable Information The following pages include mechanical, packaging, and orderable information. This information is the most current data available for the designated devices. This data is subject to change without notice and revision of thisdocument.Forbrowser-basedversionsofthisdatasheet,refertotheleft-handnavigation. 22 SubmitDocumentationFeedback Copyright©2000–2015,TexasInstrumentsIncorporated ProductFolderLinks:TPS62000 TPS62001 TPS62002 TPS62003TPS62004 TPS62005 TPS62006 TPS62007 TPS62008

PACKAGE OPTION ADDENDUM www.ti.com 6-Feb-2020 PACKAGING INFORMATION Orderable Device Status Package Type Package Pins Package Eco Plan Lead/Ball Finish MSL Peak Temp Op Temp (°C) Device Marking Samples (1) Drawing Qty (2) (6) (3) (4/5) TPS62000DGS ACTIVE VSSOP DGS 10 80 Green (RoHS NIPDAUAG Level-1-260C-UNLIM -40 to 85 AIH & no Sb/Br) TPS62000DGSG4 ACTIVE VSSOP DGS 10 80 Green (RoHS NIPDAUAG Level-1-260C-UNLIM -40 to 85 AIH & no Sb/Br) TPS62000DGSR ACTIVE VSSOP DGS 10 2500 Green (RoHS NIPDAU | NIPDAUAG Level-1-260C-UNLIM -40 to 85 AIH & no Sb/Br) TPS62000DGSRG4 ACTIVE VSSOP DGS 10 2500 Green (RoHS NIPDAUAG Level-1-260C-UNLIM -40 to 85 AIH & no Sb/Br) TPS62002DGS ACTIVE VSSOP DGS 10 80 Green (RoHS NIPDAUAG Level-1-260C-UNLIM -40 to 85 AIJ & no Sb/Br) TPS62002DGSG4 ACTIVE VSSOP DGS 10 80 Green (RoHS NIPDAUAG Level-1-260C-UNLIM -40 to 85 AIJ & no Sb/Br) TPS62002DGSR ACTIVE VSSOP DGS 10 2500 Green (RoHS NIPDAUAG Level-1-260C-UNLIM -40 to 85 AIJ & no Sb/Br) TPS62003DGS ACTIVE VSSOP DGS 10 80 Green (RoHS NIPDAUAG Level-1-260C-UNLIM -40 to 85 AIK & no Sb/Br) TPS62003DGSG4 ACTIVE VSSOP DGS 10 80 Green (RoHS NIPDAUAG Level-1-260C-UNLIM -40 to 85 AIK & no Sb/Br) TPS62003DGSR ACTIVE VSSOP DGS 10 2500 Green (RoHS NIPDAUAG Level-1-260C-UNLIM -40 to 85 AIK & no Sb/Br) TPS62003DGSRG4 ACTIVE VSSOP DGS 10 2500 Green (RoHS NIPDAUAG Level-1-260C-UNLIM -40 to 85 AIK & no Sb/Br) TPS62004DGS ACTIVE VSSOP DGS 10 80 Green (RoHS NIPDAUAG Level-1-260C-UNLIM -40 to 85 AIL & no Sb/Br) TPS62004DGSG4 ACTIVE VSSOP DGS 10 80 Green (RoHS NIPDAUAG Level-1-260C-UNLIM -40 to 85 AIL & no Sb/Br) TPS62004DGSR ACTIVE VSSOP DGS 10 2500 Green (RoHS NIPDAUAG Level-1-260C-UNLIM -40 to 85 AIL & no Sb/Br) TPS62004DGSRG4 ACTIVE VSSOP DGS 10 2500 Green (RoHS NIPDAUAG Level-1-260C-UNLIM -40 to 85 AIL & no Sb/Br) TPS62005DGS ACTIVE VSSOP DGS 10 80 Green (RoHS NIPDAUAG Level-1-260C-UNLIM -40 to 85 AIM & no Sb/Br) TPS62005DGSR ACTIVE VSSOP DGS 10 2500 Green (RoHS NIPDAUAG Level-1-260C-UNLIM -40 to 85 AIM & no Sb/Br) Addendum-Page 1

PACKAGE OPTION ADDENDUM www.ti.com 6-Feb-2020 Orderable Device Status Package Type Package Pins Package Eco Plan Lead/Ball Finish MSL Peak Temp Op Temp (°C) Device Marking Samples (1) Drawing Qty (2) (6) (3) (4/5) TPS62006DGS ACTIVE VSSOP DGS 10 80 Green (RoHS NIPDAUAG Level-1-260C-UNLIM -40 to 85 AIN & no Sb/Br) TPS62006DGSR ACTIVE VSSOP DGS 10 2500 Green (RoHS NIPDAUAG Level-1-260C-UNLIM -40 to 85 AIN & no Sb/Br) TPS62007DGS ACTIVE VSSOP DGS 10 80 Green (RoHS NIPDAU | NIPDAUAG Level-1-260C-UNLIM -40 to 85 AIO & no Sb/Br) TPS62007DGSG4 ACTIVE VSSOP DGS 10 80 Green (RoHS NIPDAUAG Level-1-260C-UNLIM -40 to 85 AIO & no Sb/Br) TPS62007DGSR ACTIVE VSSOP DGS 10 2500 Green (RoHS NIPDAU | NIPDAUAG Level-1-260C-UNLIM -40 to 85 AIO & no Sb/Br) TPS62007DGSRG4 ACTIVE VSSOP DGS 10 2500 Green (RoHS NIPDAUAG Level-1-260C-UNLIM -40 to 85 AIO & no Sb/Br) TPS62008DGS ACTIVE VSSOP DGS 10 80 Green (RoHS NIPDAUAG Level-1-260C-UNLIM -40 to 85 AJI & no Sb/Br) TPS62008DGSR ACTIVE VSSOP DGS 10 2500 Green (RoHS NIPDAUAG Level-1-260C-UNLIM -40 to 85 AJI & no Sb/Br) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based flame retardants must also meet the <=1000ppm threshold requirement. (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. Addendum-Page 2

PACKAGE OPTION ADDENDUM www.ti.com 6-Feb-2020 (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF TPS62000, TPS62004, TPS62005, TPS62007 : •Automotive: TPS62000-Q1, TPS62004-Q1, TPS62005-Q1, TPS62007-Q1 NOTE: Qualified Version Definitions: •Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects Addendum-Page 3

PACKAGE MATERIALS INFORMATION www.ti.com 1-May-2019 TAPE AND REEL INFORMATION *Alldimensionsarenominal Device Package Package Pins SPQ Reel Reel A0 B0 K0 P1 W Pin1 Type Drawing Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant (mm) W1(mm) TPS62000DGSR VSSOP DGS 10 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 TPS62002DGSR VSSOP DGS 10 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 TPS62003DGSR VSSOP DGS 10 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 TPS62004DGSR VSSOP DGS 10 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 TPS62005DGSR VSSOP DGS 10 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 TPS62006DGSR VSSOP DGS 10 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 TPS62007DGSR VSSOP DGS 10 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 TPS62008DGSR VSSOP DGS 10 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 PackMaterials-Page1

PACKAGE MATERIALS INFORMATION www.ti.com 1-May-2019 *Alldimensionsarenominal Device PackageType PackageDrawing Pins SPQ Length(mm) Width(mm) Height(mm) TPS62000DGSR VSSOP DGS 10 2500 350.0 350.0 43.0 TPS62002DGSR VSSOP DGS 10 2500 350.0 350.0 43.0 TPS62003DGSR VSSOP DGS 10 2500 350.0 350.0 43.0 TPS62004DGSR VSSOP DGS 10 2500 350.0 350.0 43.0 TPS62005DGSR VSSOP DGS 10 2500 350.0 350.0 43.0 TPS62006DGSR VSSOP DGS 10 2500 350.0 350.0 43.0 TPS62007DGSR VSSOP DGS 10 2500 350.0 350.0 43.0 TPS62008DGSR VSSOP DGS 10 2500 350.0 350.0 43.0 PackMaterials-Page2

PACKAGE OUTLINE DGS0010A VSSOP - 1.1 mm max height SCALE 3.200 SMALL OUTLINE PACKAGE C 5.05 4.75 TYP SEATING PLANE A PIN 1 ID 0.1 C AREA 8X 0.5 10 1 3.1 2X 2.9 NOTE 3 2 5 6 0.27 10X 0.17 B 3.1 0.1 C A B 1.1 MAX 2.9 NOTE 4 0.23 TYP SEE DETAIL A 0.13 0.25 GAGE PLANE 0.15 0.7 0 - 8 0.05 0.4 DETAIL A TYPICAL 4221984/A 05/2015 NOTES: 1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not exceed 0.15 mm per side. 4. This dimension does not include interlead flash. Interlead flash shall not exceed 0.25 mm per side. 5. Reference JEDEC registration MO-187, variation BA. www.ti.com

EXAMPLE BOARD LAYOUT DGS0010A VSSOP - 1.1 mm max height SMALL OUTLINE PACKAGE 10X (1.45) 10X (0.3) SYMM (R0.05) TYP 1 10 SYMM 8X (0.5) 5 6 (4.4) LAND PATTERN EXAMPLE SCALE:10X SOOPLEDNEINRG MASK METAL MSOELTDAEL RU NMDAESRK SOOPLEDNEINRG MASK 0.05 MAX 0.05 MIN ALL AROUND ALL AROUND NON SOLDER MASK SOLDER MASK DEFINED DEFINED SOLDER MASK DETAILS NOT TO SCALE 4221984/A 05/2015 NOTES: (continued) 6. Publication IPC-7351 may have alternate designs. 7. Solder mask tolerances between and around signal pads can vary based on board fabrication site. www.ti.com

EXAMPLE STENCIL DESIGN DGS0010A VSSOP - 1.1 mm max height SMALL OUTLINE PACKAGE 10X (1.45) SYMM (R0.05) TYP 10X (0.3) 1 10 SYMM 8X (0.5) 5 6 (4.4) SOLDER PASTE EXAMPLE BASED ON 0.125 mm THICK STENCIL SCALE:10X 4221984/A 05/2015 NOTES: (continued) 8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations. 9. Board assembly site may have different recommendations for stencil design. www.ti.com

IMPORTANTNOTICEANDDISCLAIMER TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you permission to use these resources only for development of an application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these resources. TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for TI products. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2020, Texas Instruments Incorporated