TNPW www.vishay.com Vishay Lead (Pb)-Bearing High Stability Thin Film Chip Resistors FEATURES • Metal film layer on high quality ceramic • SnPb termination plating, Pb content > 6 % • Excellent overall stability at different environmental conditions  0.05 % (1000 h rated power at 70 °C) • Low temperature coefficient and tight tolerances (± 0.1 %; ± 10 ppm/K) • Single lot date code available APPLICATIONS • Military • Avionics • Industrial TNPW High Stability Thin Film Chip Resistors are the perfect choice for most fields of modern electronics where lead (Pb)-bearing terminations are mandatory and reliability and stability are of major concern. TECHNICAL SPECIFICATIONS DESCRIPTION TNPW0402 TNPW0603 TNPW0805 TNPW1206 TNPW1210 (1) Imperial size 0402 0603 0805 1206 1210 Metric size code RR1005M RR1608M RR2012M RR3216M RR3225M Resistance range 10  to 100 k 10  to 332 k 10  to 1 M 10  to 2 M 10  to 3.01 M Resistance tolerance ± 1 %; ± 0.5 %; ± 0.1 % Temperature coefficient ± 50 ppm/K; ± 25 ppm/K; ± 15 ppm/K; ± 10 ppm/K Climatic category (LCT/UCT/days) 55/125/56 55/125/56 55/125/56 55/125/56 55/125/56 Rated dissipation, P (2) 0.063 W 0.1 W 0.125 W 0.25 W 0.33 W 70 Operating voltage, U AC or DC 50 V 75 V 150 V 200 V 200 V max. RMS Permissible film temperature, F max. 155 °C Operating Temperature Range -55 °C to 125 °C (155 °C) Thermal resistance (3) 870 K/W 550 K/W 440 K/W 220 K/W 170 K/W Insulation voltage: U 1 min 75 V 100 V 200 V 300 V 300 V ins Continuous 75 V 75 V 75 V 75 V 75 V Failure rate: FITobserved  0.3 x 10-9/h Notes (1) The detail specification EN140401-801 does not cover this product size. (2) Rated voltage P x R. The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature is not exceeded. (3) Measuring conditions in accordance with EN 140401-801. Revision: 24-Jan-14 1 Document Number: 31006 For technical questions, contact: thinfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

TNPW www.vishay.com Vishay TEMPERATURE COEFFICIENT AND RESISTANCE RANGE TYPE TCR TOLERANCE RESISTANCE E-SERIES ±50 ppm/K ± 1 % E24; E96 10  to 100 k ± 0.5 % ±25 ppm/K TNPW0402 ± 0.1 % E24; E192 ±15 ppm/K ± 0.1 % 47  to 100 k ±10 ppm/K ± 0.1 % ±50 ppm/K ± 1 % E24; E96 ± 0.5 % 10  to 332 k ±25 ppm/K TNPW0603 ± 0.1 % E24; E192 ±15 ppm/K ± 0.1 % 47  to 332 k ±10 ppm/K ± 0.1 % ±50 ppm/K ± 1 % E24; E96 ± 0.5 % 10  to 1.0 M ±25 ppm/K TNPW0805 ± 0.1 % E24; E192 ±15 ppm/K ± 0.1 % 47  to 1.0 M ±10 ppm/K ± 0.1 % ±50 ppm/K ± 1 % E24; E96 ± 0.5 % 10  to 2.0 M ±25 ppm/K TNPW1206 ± 0.1 % E24; E192 ±15 ppm/K ± 0.1 % 47  to 2.0 M ±10 ppm/K ± 0.1 % ±50 ppm/K ± 1 % E24; E96 10  to 3.01 M ± 0.5 % ±25 ppm/K TNPW1210 ± 0.1 % E24; E192 ±15 ppm/K ± 0.1 % 47  to 2.13 M ±10 ppm/K ± 0.1 % PART NUMBER AND PRODUCT DESCRIPTION Part Number: TNPW12061K32DETA T N P W 1 2 0 6 1 K 3 2 D E T A TYPE/SIZE RESISTANCE TOLERANCE TCR PACKAGING SPECIAL TNPW0402 R = Decimal B = ± 0.1 % H = ± 50 ppm/K TP Blank = Standard TNPW0603 K = Thousand D = ± 0.5 % E = ± 25 ppm/K TD 0H = Single lot TNPW0805 M = Million F = ± 1.0 % X = ± 15 ppm/K CN date code TNPW1206 (4 digits) Y = ± 10 ppm/K TA TNPW1210 TC Product Description: TNPW-1206 1.32K 0.5 % T-9 RT1 TNPW-1206 1.32K 0.5 % T-9 RT1 TYPE/SIZE RESISTANCE TOLERANCE TCR PACKAGING SPECIAL TNPW-0402 Examples: ± 0.1 % T-2 = ± 50 ppm/K TP1 Blank = Standard TNPW-0603 1K32 = 1320  ± 0.5 % T-9 = ± 25 ppm/K RT7 BV20545 = TNPW-0805 99.68K = 99 680  ± 1.0 % T-10 = ± 15 ppm/K R52 Single lot date code TNPW-1206 360 = 360  T-13 = ± 10 ppm/K RT1 TNPW-1210 RT6 Notes • The products can be ordered using either the PRODUCT DESCRIPTION or the PART NUMBER. Revision: 24-Jan-14 2 Document Number: 31006 For technical questions, contact: thinfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

TNPW www.vishay.com Vishay PACKAGING PACKAGING REEL TYPE CODE QUANTITY WIDTH PITCH STYLE DIAMETER TNPW0402 TP1 = TP (1) 1000 8 mm 2 180 mm/7" TNPW0402 RT7 = TD 10 000 8 mm 2 180 mm/7" TNPW0603 TNPW0805 Tape and reel TNPW1206 R52 = CN (1) 1000 cardboard tape 8 mm 4 180 mm/7" TNPW1210 acc. IEC 60286-3 Type I TNPW0603 TNPW0805 RT1 = TA 5000 8 mm 4 180 mm/7" TNPW1206 TNPW1210 Note (1) 1000 pieces packaging quantity is only available for precision resistors with tolerance ± 0.1 %. DESCRIPTION RELATED PRODUCTS The production is strictly controlled and follows an extensive For ordering TNPW with lead free terminations please refer set of instructions established for reproducibility. A to latest edition of data sheet TNPW e3, homogeneous film of metal alloy is deposited on a high (www.vishay.com/doc?28758). grade ceramic body (Al2O3) and conditioned to achieve the TNPS .... ESCC high-reliability thin film chip resistors are the desired temperature coefficient. A special laser is used to premium choice for design and manufacture of equipment, achieve the target value by smoothly cutting an appropriate where mature technology and proven reliability are of groove in the resistive layer without damaging the ceramics. utmost importance. The resistor elements are covered by a protective coating (www.vishay.com/doc?28789) designed for electrical, mechanical and climatic protection. The terminations receive a final tin-lead (SnPb) on nickel plating. The result of the determined production is verified by an extensive testing procedure performed on 100 % of the individual resistors. Only accepted products are placed into the tape in accordance with IEC 60286-3, Type I. Resistance marking is not applied on TNPW0402. ASSEMBLY The resistors are suitable for processing on automatic SMD assembly systems. They are suitable for automatic soldering using wave, reflow or vapour phase as shown in IEC 61760-1 (1). Solderability is specified for 2 years after production. The permitted storage time is 20 years. The terminations are plated with SnPb solder, controlled for a minimum lead Pb content of 6 % for compliance with the respective requirements of Bellcore, MIL and ESCC specifications. The encapsulation is resistant to all cleaning solvents commonly used in the electronics industry, including alcohols, esters and aqueous solutions. The suitability of conformal coatings, if applied, shall be qualified by appropriate means to ensure the long-term stability of the whole system. Revision: 24-Jan-14 3 Document Number: 31006 For technical questions, contact: thinfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

TNPW www.vishay.com Vishay B 3 d V n 120 V/ 2 Linearity A i3110100 TTTNNTNNPPPWPWWW0004618002023056 ent Noise in µ 00..153 TNPW0402 TTNNPPWW00860053 Non- 90 Curr 0.1 TNPW1206 80 0.05 0.03 70 60 0.01 10 100 1K 10K 100K 100 1K 10K 100K 1M Resistance Value in Ω Resistance Value in Ω Non-Linearity Current Noise 60 60 ϑ° TNPW0603 % TNPW0603 hase Angle in 42000 10 Ω [Z]-RO in RO42000 11000 ΩΩ P 100 Ω 1 kΩ - 20 - 20 1 kΩ - 40 - 40 4.75 kΩ - 60 4.75 kΩ - 60 10 kΩ - 80 10 kΩ - 80 1 5 10 50 100 500 1000 1 5 10 50 100 500 1000 Frequency f in MHz Frequency f in MHz HF Performance HF Performance 60 60 ϑ°n TNPW0805 % TNPW0805 gle i 40 O in 40 ase An 20 10 Ω [Z]-RRO20 10 Ω Ph 0 0 100 Ω 100 Ω 1 kΩ - 20 - 20 1 kΩ - 40 - 40 - 60 - 60 10 kΩ 10 kΩ - 80 - 80 1 5 10 50 100 500 1000 1 5 10 50 100 500 1000 Frequency f in MHz Frequency f in MHz HF Performance HF Performance Revision: 24-Jan-14 4 Document Number: 31006 For technical questions, contact: thinfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

TNPW www.vishay.com Vishay % 120 3K ower in 100 age in V 1K TNPW0805 ated P 80 st Volt TNPW0603 R e T 60 100 40 20 EN 0 10 - 55 - 25 0 25 50 75 100 125 150 175 10R 100R 1K 10K 100K 70Ambient Temperature in °C Resistance in Ω Derating Single-Pulse High Voltage Overload Test 1.2/50 μs EN 140000 4.27 Note • The solid line is based on IEC/EN reference test conditions which  is considered as standard mode. However, above that the  maximum permissible film temperature is 155 °C (dashed line). V 3K ax.100 n ^Pm TNPW0805 e i TNPW0805 d oltag 1K Loa 10 est V TNPW0603 ulse TNPW0603 T P 1 100 0.1 10 0.01 10R 100R 1K 10K 100K 10-5 10-4 10-3 10-2 10-1 1 10 Resistance in Ω Pulse Durationt i Single-Pulse High Voltage Overload Test Single Pulse 10/700 μs EN 140000 4.27 Maximum pulse load, single pulse; applicable if P  0 and n  1000 and Û  Ûmax.; for permissible resistance change equivalent to 8000 h operation in standard operation mode ax.100 x. 500 ^Pm Ûma TNPW0805 oad 10 TNPW0805 ge 400 L a e olt s V TNPW0603 ul TNPW0603 e 300 P s s 1 ul u P o u 200 n nti o 0.1 C 100 Secondary conditions: a) Psee diagram (Pulse Rating) b)ϑu ≤ 70 °C 0.01 0 10-5 10-4 10-3 10-2 10-1 1 10 10-5 10-4 10-3 10-2 10-1 1 10 Pulse Durationt Pulse Durationt i i Maximum pulse load, continuous pulses; Maximum pulse voltage, single and continuous pulses; ˆ ˆ applicable if P  P (amb) and Û  Ûmax.; applicable if P  Pmax.; for permissible resistance change equivalent to 8000 h for permissible resistance change equivalent to 8000 h operation in standard operation mode operation in standard operation mode Continuous Pulse Pulse Voltage Revision: 24-Jan-14 5 Document Number: 31006 For technical questions, contact: thinfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

TNPW www.vishay.com Vishay TEST AND REQUIREMENTS All tests are carried out in accordance with the following Unless otherwise specified the following values apply: specifications: Temperature: 15 °C to 35 °C IEC 60115-1, generic specification (includes tests) Relative humidity: 45 % to 75 % EN 140400, sectional specification (includes schedule for Air pressure: 86 kPa to 106 kPa (860 mbar to 1060 mbar). qualification approval) The components are mounted for testing on boards in EN 140401-801, detail specification (includes schedule for accordance with EN60115-1, 4.31 unless otherwise conformance inspection) specified. The parameters stated in the Test Procedures and The testing also covers most of the requirements specified Requirements table are based on the required tests and by EIA/ECA-703 and JIS-C-5201-1. The tests are carried out permitted limits of EN140401-801. under standard atmospheric conditions in accordance with IEC 60068-1, 5.3. A climate category is applied, defined by the lower category temperature (LCT), the upper category temperature (UCT), and the number of days of the damp heat, steady-state test (56). TEST PROCEDURES AND REQUIREMENTS IEC 60068-2 EN 60115-1  TEST TEST PROCEDURE REQUIREMENTS PERMISSIBLE CHANGE (R) CLAUSE METHOD Stability for product type: TNPW0402 TNPW0603 TNPW0805 10  to < 100  100  to 3.01 M 10  to 3.01 M TNPW1206 TNPW1210 4.5 - Resistance - ± 0.1 % ± 1 %; ± 0.5 % Temperature At (20/- 55/20) °C ± 50 ppm/K; 4.8.4.2 - ± 25 ppm/K; ± 15 ppm/K; ± 10 ppm/K coefficient and (20/125/20) °C ± 25 ppm/K U = P x R 70 Endurance or  Umax.; 4.25.1 - 1.5 h on; 0.5 h off; at 70 °C 70 °C; 1000 h ± (0.1 % R + 0.02 ) ± (0.05 % R + 0.01 ) ± (0.25 % R + 0.05 ) Endurance at upper 4.25.3 - 125 °C; 1000 h ± (0.1 % R + 0.02 ) ± (0.05 % R + 0.01 ) ± (0.5 % R + 0.05 ) category temperature Short time U = 2.5 x P x R 4.13 - 70 ± (0.05 % R + 0.01 ) ± (0.02 % R + 0.01 ) ± (0.1 % R + 0.02 ) overload 2 x Umax.; 2 s (40 ± 2) °C; Damp heat, 4.24 78 (Cab) (93 ± 3) % RH; ± (0.1 % R + 0.02 ) ± (0.05 % R + 0.01 ) ± (0.5 % R + 0.05 ) steady state 56 days 30 min at - 55 °C: Rapid change 4.19 14 (Na) 30 min at 125 °C; ± (0.05 % R + 0.01 ) ± (0.02 % R + 0.01 ) ± (0.1 % R + 0.02 ) of temperature 5 cycles Solder bath method; Resistance to 4.18.2 58 (Td) (260 ± 5) °C; ± (0.05 % R + 0.01 ) ± (0.02 % R + 0.01 ) ± (0.1 % R + 0.02 ) soldering heat (10 ± 1) s Flammability, IEC 60695-11-5; 4.35 - needle flame No burning after 30 s 10 s test Revision: 24-Jan-14 6 Document Number: 31006 For technical questions, contact: thinfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

TNPW www.vishay.com Vishay DIMENSIONS L Tt W H Tb DIMENSIONS AND MASS H L W T T MASS TYPE t b (mm) (mm) (mm) (mm) (mm) (mg) TNPW0402 0.35 ± 0.05 1.0 ± 0.05 0.5 ± 0.05 0.2 ± 0.10 0.2 ± 0.10 0.65 TNPW0603 0.45 ± 0.10 1.6 ± 0.10 0.85 ± 0.10 0.3 ± 0.20 0.3 ± 0.20 2 TNPW0805 0.45 ± 0.10 2.0 ± 0.15 1.25 ± 0.15 0.4 ± 0.20 0.4 ± 0.20 5.5 TNPW1206 0.55 ± 0.10 3.2 ± 0.15 1.6 ± 0.15 0.5 ± 0.25 0.5 ± 0.25 10 TNPW1210 0.60 ± 0.15 3.2 ± 0.15 2.45 ± 0.15 0.5 ± 0.25 0.5 ± 0.25 16 SOLDER PAD DIMENSIONS G X Y SOLDER PAD DIMENSIONS REFLOW SOLDERING WAVE SOLDERING TYPE Y X G Y X G (mm) (mm) (mm) (mm) (mm) (mm) TNPW0402 0.4 0.6 0.5 - - - TNPW0603 0.5 0.9 1.0 0.9 0.9 1.0 TNPW0805 0.7 1.3 1.2 0.9 1.3 1.3 TNPW1206 0.9 1.7 2.0 1.1 1.7 2.3 TNPW1210 0.9 2.5 2.0 1.1 2.5 2.3 Revision: 24-Jan-14 7 Document Number: 31006 For technical questions, contact: thinfilmchip@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROV E RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose o r the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustainin g applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk . Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this documen t or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2019 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 01-Jan-2019 1 Document Number: 91000