(cid:1)(cid:2)(cid:3)(cid:4)(cid:5)(cid:6)(cid:7)(cid:8)(cid:9)(cid:5)(cid:4)(cid:10) (cid:11)(cid:12)(cid:13)(cid:14)(cid:13)(cid:15) (cid:7)(cid:16)(cid:17)(cid:18)(cid:15) (cid:9)(cid:19)(cid:20)(cid:21)(cid:9)(cid:22) (cid:23)(cid:24) (cid:12)(cid:15) (cid:25)(cid:26)(cid:24)(cid:27)(cid:28)(cid:29)(cid:22) (cid:30)(cid:18)(cid:12)(cid:31) (cid:8)!(cid:12)(cid:13)"(cid:14)#(cid:12)(cid:13)(cid:17) (cid:28)(cid:13)#(cid:17)$(cid:31)(cid:15)!(cid:13) (cid:7)%$&(cid:18)’(cid:18)(cid:13)(cid:14) Data Manual February 2004 Digital Audio Products SLWS106H

Contents Section Title Page 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1−1 1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1−1 1.2 Functional Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1−3 1.3 Terminal Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1−4 1.4 Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1−5 1.5 Terminal Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1−5 2 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2−1 2.1 Absolute Maximum Ratings Over Operating Free-Air Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2−1 2.2 Recommended Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . 2−1 2.3 Electrical Characteristics Over Recommended Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2−2 2.3.1 ADC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2−2 2.3.2 DAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2−3 2.3.3 Analog Line Input to Line Output (Bypass) . . . . . . . . . . . . . 2−3 2.3.4 Stereo Headphone Output . . . . . . . . . . . . . . . . . . . . . . . . . . . 2−4 2.3.5 Analog Reference Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2−4 2.3.6 Digital I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2−4 2.3.7 Supply Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2−4 2.4 Digital-Interface Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2−5 2.4.1 Audio Interface (Master Mode) . . . . . . . . . . . . . . . . . . . . . . . 2−5 2.4.2 Audio Interface (Slave-Mode) . . . . . . . . . . . . . . . . . . . . . . . . 2−6 2.4.3 Three-Wire Control Interface (SDIN) . . . . . . . . . . . . . . . . . . 2−7 2.4.4 Two-Wire Control Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . 2−7 3 How to Use the TLV320AIC23B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3−1 3.1 Control Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3−1 3.1.1 SPI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3−1 3.1.2 2-Wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3−1 3.1.3 Register Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3−2 3.2 Analog Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3−5 3.2.1 Line Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3−5 3.2.2 Microphone Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3−6 3.2.3 Line Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3−6 3.2.4 Headphone Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3−6 3.2.5 Analog Bypass Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3−7 3.2.6 Sidetone Insertion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3−7 3.3 Digital Audio Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3−7 3.3.1 Digital Audio-Interface Modes . . . . . . . . . . . . . . . . . . . . . . . . 3−7 iii

3.3.2 Audio Sampling Rates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3−9 3.3.3 Digital Filter Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . 3−11 A Mechanical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A−1 iv

List of Illustrations Figure Title Page 2−1 System-Clock Timing Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2−5 2−2 Master-Mode Timing Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2−5 2−3 Slave-Mode Timing Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2−6 2−4 Three-Wire Control Interface Timing Requirements . . . . . . . . . . . . . . . . . . 2−7 2−5 Two-Wire Control Interface Timing Requirements . . . . . . . . . . . . . . . . . . . 2−7 3−1 SPI Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3−1 3−2 2-Wire Compatible Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3−2 3−3 Analog Line Input Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3−5 3−4 Microphone Input Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3−6 3−5 Right-Justified Mode Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3−7 3−6 Left-Justified Mode Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3−8 3−7 I2S Mode Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3−8 3−8 DSP Mode Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3−8 3−9 Digital De-Emphasis Filter Response − 44.1 kHz Sampling . . . . . . . . . . . 3−12 3−10 Digital De-Emphasis Filter Response − 48 kHz Sampling . . . . . . . . . . . . 3−12 3−11 ADC Digital Filter Response 0: USB Mode (Group Delay = 12 Output Samples) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3−13 3−12 ADC Digital Filter Ripple 0: USB (Group Delay = 20 Output Samples) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3−13 3−13 ADC Digital Filter Response 1: USB Mode Only . . . . . . . . . . . . . . . . . . . . 3−14 3−14 ADC Digital Filter Ripple 1: USB Mode Only . . . . . . . . . . . . . . . . . . . . . . . . 3−14 3−15 ADC Digital Filter Response 2: USB mode and Normal Modes (Group Delay = 3 Output Samples) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3−15 3−16 ADC Digital Filter Ripple 2: USB Mode and Normal Modes . . . . . . . . . . . 3−15 3−17 ADC Digital Filter Response 3: USB Mode Only . . . . . . . . . . . . . . . . . . . . 3−16 3−18 ADC Digital Filter Ripple 3: USB Mode Only . . . . . . . . . . . . . . . . . . . . . . . . 3−16 3−19 DAC Digital Filter Response 0: USB Mode . . . . . . . . . . . . . . . . . . . . . . . . . 3−17 3−20 DAC Digital Filter Ripple 0: USB Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3−17 3−21 DAC Digital Filter Response 1: USB Mode Only . . . . . . . . . . . . . . . . . . . . 3−18 3−22 DAC Digital Filter Ripple 1: USB Mode Only . . . . . . . . . . . . . . . . . . . . . . . . 3−18 3−23 DAC Digital Filter Response 2: USB Mode and Normal Modes . . . . . . . . 3−19 3−24 DAC Digital Filter Ripple 2: USB Mode and Normal Modes . . . . . . . . . . . 3−19 3−25 DAC Digital Filter Response 3: USB Mode Only . . . . . . . . . . . . . . . . . . . . 3−20 3−26 DAC Digital Filter Ripple 3: USB Mode Only . . . . . . . . . . . . . . . . . . . . . . . . 3−20 v

vi

1 Introduction The TLV320AIC23B is a high-performance stereo audio codec with highly integrated analog functionality. The analog-to-digital converters (ADCs) and digital-to-analog converters (DACs) within the TLV320AIC23B use multibit sigma-delta technology with integrated oversampling digital interpolation filters. Data-transfer word lengths of 16, 20, 24, and 32 bits, with sample rates from 8 kHz to 96 kHz, are supported. The ADC sigma-delta modulator features third-order multibit architecture with up to 90-dBA signal-to-noise ratio (SNR) at audio sampling rates up to 96 kHz, enabling high-fidelity audio recording in a compact, power-saving design. The DAC sigma-delta modulator features a second-order multibit architecture with up to 100-dBA SNR at audio sampling rates up to 96 kHz, enabling high-quality digital audio-playback capability, while consuming less than 23 mW during playback only. The TLV320AIC23B is the ideal analog input/output (I/O) choice for portable digital audio-player and recorder applications, such as MP3 digital audio players. Integrated analog features consist of stereo-line inputs with an analog bypass path, a stereo headphone amplifier, with analog volume control and mute, and a complete electret-microphone-capsule biasing and buffering solution. The headphone amplifier is capable of delivering 30 mW per channel into 32 Ω. The analog bypass path allows use of the stereo-line inputs and the headphone amplifier with analog volume control, while completely bypassing the codec, thus enabling further design flexibility, such as integrated FM tuners. A microphone bias-voltage output provides a low-noise current source for electret-capsule biasing. The AIC23B has an integrated adjustable microphone amplifier (gain adjustable from 1 to 5) and a programmable gain microphone amplifier (0 dB or 20 dB). The microphone signal can be mixed with the output signals if a sidetone is required. While the TLV320AIC23B supports the industry-standard oversampling rates of 256 f and 384 f , unique s s oversampling rates of 250 f and 272 f are provided, which optimize interface considerations in designs using TI C54x s s digital signal processors (DSPs) and universal serial bus (USB) data interfaces. A single 12-MHz crystal can supply clocking to the DSP, USB, and codec. The TLV320AIC23B features an internal oscillator that, when connected to a 12-MHz external crystal, provides a system clock to the DSP and other peripherals at either 12 MHz or 6 MHz, using an internal clock buffer and selectable divider. Audio sample rates of 48 kHz and compact-disc (CD) standard 44.1 kHz are supported directly from a 12-MHz master clock with 250 f and 272 f oversampling rates. s s Low power consumption and flexible power management allow selective shutdown of codec functions, thus extending battery life in portable applications. This design solution, coupled with the industry’s smallest package, the TI proprietary MicroStar Junior using only 25 mm2 of board area, makes powerful portable stereo audio designs easily realizable in a cost-effective, space-saving total analog I/O solution: the TLV320AIC23B. 1.1 Features • High-Performance Stereo Codec − 90-dB SNR Multibit Sigma-Delta ADC (A-weighted at 48 kHz) − 100-dB SNR Multibit Sigma-Delta DAC (A-weighted at 48 kHz) − 1.42 V – 3.6 V Core Digital Supply: Compatible With TI C54x DSP Core Voltages − 2.7 V – 3.6 V Buffer and Analog Supply: Compatible Both TI C54x DSP Buffer Voltages − 8-kHz – 96-kHz Sampling-Frequency Support • Software Control Via TI McBSP-Compatible Multiprotocol Serial Port − 2-wire-Compatible and SPI-Compatible Serial-Port Protocols − Glueless Interface to TI McBSPs • Audio-Data Input/Output Via TI McBSP-Compatible Programmable Audio Interface − I2S-Compatible Interface Requiring Only One McBSP for both ADC and DAC − Standard I2S, MSB, or LSB Justified-Data Transfers − 16/20/24/32-Bit Word Lengths MicroStar Junior is a trademark of Texas Instruments. 1−1

− Audio Master/Slave Timing Capability Optimized for TI DSPs (250/272 f ), USB mode s − Industry-Standard Master/Slave Support Provided Also (256/384 f ), Normal mode s − Glueless Interface to TI McBSPs • Integrated Total Electret-Microphone Biasing and Buffering Solution − Low-Noise MICBIAS pin at 3/4 AVDD for Biasing of Electret Capsules − Integrated Buffer Amplifier With Tunable Fixed Gain of 1 to 5 − Additional Control-Register Selectable Buffer Gain of 0 dB or 20 dB • Stereo-Line Inputs − Integrated Programmable Gain Amplifier − Analog Bypass Path of Codec • ADC Multiplexed Input for Stereo-Line Inputs and Microphone • Stereo-Line Outputs − Analog Stereo Mixer for DAC and Analog Bypass Path • Volume Control With Mute on Input and Output • Highly Efficient Linear Headphone Amplifier − 30 mW into 32 Ω From a 3.3-V Analog Supply Voltage • Flexible Power Management Under Total Software Control − 23-mW Power Consumption During Playback Mode − Standby Power Consumption <150 µW − Power-Down Power Consumption <15 µW • Industry’s Smallest Package: 32-Pin TI Proprietary MicroStar Junior − 25 mm2 Total Board Area − 28-Pin TSSOP Also Is Available (62 mm2 Total Board Area) • Ideally Suitable for Portable Solid-State Audio Players and Recorders 1−2

1.2 Functional Block Diagram VMID AVDD VMID 1.0X 50 kΩ DSPcodec VDAC TLV320AIC23B 1.0X 50 kΩ VADC 1.0X AGND CS Control SDIN 1.5X Interface SCLK MICBIAS 12 to −34.5 dB, MODE 1.5 dB Steps Line 2:1 Σ−∆ RLINEIN Mute MUX ADC 50 kΩ Bypass Mute, Mute 0 dB, 20 dB 10 kΩ VADC MICIN VMID Line 2:1 Σ−∆ LLINEIN Mute MUX ADC DVDD Digital BVDD 12 to −34 dB, Filters Side Tone 1.5 dB Steps DGND Mute HPVDD Headphone 6 to −73 dB, Bypass HPGND Driver 1 dB Steps Mute Σ Σ−∆ RHPOUT DAC ROUT VDAC LOUT Σ Σ−∆ LHPOUT DAC Headphone 6 to −73 dB, Driver 1 dB Steps CLKIN Divider (1x, 1/2x) LRCIN XTI/MCLK CLKOUT Digital DIN OSC Divider Audio LRCOUT XTO (1x, 1/2x) Interface DOUT CLKOUT BCLK NOTE: MCLK, BCLK, and SCLK are all asynchronous to each other. 1−3

1.3 Terminal Assignments GQE/ZQE PACKAGE (TOP VIEW) T U K O D D D NC DIN BCL CLK BVD DGN DVD XTO NC 25 24 23 22 21 20 19 18 17 LRCIN 26 16 XTI/MCLK DOUT 27 15 SCLK LRCOUT 28 14 SDIN HPVDD 29 13 MODE LHPOUT 30 12 CS RHPOUT 31 11 LLINEIN HPGND 32 10 RLINEIN 1 2 3 4 5 6 7 8 9 C T T D D D S N C N LOU ROU AVD AGN VMI CBIA MICI N RHD PACKAGE MI (TOP VIEW) NC − No internal connection K T L U C K O D D D M PW PACKAGE CL LK VD GN VD TO TI/ (TOP VIEW) B C B D D X X 8 7 6 5 4 3 2 BVDD 1 28 DGND 2 2 2 2 2 2 2 CLKOUT 2 27 DVDD BCLK 3 26 XTO DIN 1 21 SCLK DIN 4 25 XTI/MCLK LRCIN 2 20 SDIN LRCIN 5 24 SCLK DOUT 6 23 SDIN DOUT 3 19 MODE LRCOUT 7 22 MODE LROUT 4 18 CS HPVDD 8 21 CS LHPOUT 9 20 LLINEIN HPVDD 5 17 LLNEIN RHPOUT 10 19 RLINEIN HPGND 11 18 MICIN LHPOUT 6 16 RUNEIN LOUT 12 17 MICBIAS RHPOUT 7 15 MICIN ROUT 13 16 VMID AVDD 14 15 AGND 8 9 0 1 2 3 4 1 1 1 1 1 D T T D D D S PGN LOU ROU AVD AGN VMI CBIA H MI 1−4

1.4 Ordering Information PACKAGE TA 32-Pin 28-Pin 28-Pin MicroStar Junior GQE/ZQE TSSOP PW PQFP RHD −10°C to 70°C TLV320AIC23BGQE/ZQE TLV320AIC23BPW TLV320AIC23BRHD −40°C to 85°C TLV320AIC23BIGQE/ZQE TLV320AIC23BIPW TLV320AIC23BIRHD 1.5 Terminal Functions TERMINAL NO. II//OO DDEESSCCRRIIPPTTIIOONN NAME GQE/ PW RHD ZQE AGND 5 15 12 Analog supply return AVDD 4 14 11 Analog supply input. Voltage level is 3.3 V nominal. BCLK 23 3 28 I/O I2S serial-bit clock. In audio master mode, the AIC23B generates this signal and sends it to the DSP. In audio slave mode, the signal is generated by the DSP. BVDD 21 1 26 Buffer supply input. Voltage range is from 2.7 V to 3.6 V. CLKOUT 22 2 27 O Clock output. This is a buffered version of the XTI input and is available in 1X or 1/2X frequencies of XTI. Bit 07 in the sample rate control register controls frequency selection. CS 12 21 18 I Control port input latch/address select. For SPI control mode this input acts as the data latch control. For 2-wire control mode this input defines the seventh bit in the device address field. See Section 3.1 for details. DIN 24 4 1 I I2S format serial data input to the sigma-delta stereo DAC DGND 20 28 25 Digital supply return DOUT 27 6 3 O I2S format serial data output from the sigma-delta stereo ADC DVDD 19 27 24 Digital supply input. Voltage range is 1.4 V to 3.6 V. HPGND 32 11 8 Analog headphone amplifier supply return HPVDD 29 8 5 Analog headphone amplifier supply input. Voltage level is 3.3 V nominal. LHPOUT 30 9 6 O Left stereo mixer-channel amplified headphone output. Nominal 0-dB output level is 1 VRMS. Gain of –73 dB to 6 dB is provided in 1-dB steps. LLINEIN 11 20 17 I Left stereo-line input channel. Nominal 0-dB input level is 1 VRMS. Gain of –34.5 dB to 12 dB is provided in 1.5-dB steps. LOUT 2 12 9 O Left stereo mixer-channel line output. Nominal output level is 1.0 VRMS. LRCIN 26 5 2 I/O I2S DAC-word clock signal. In audio master mode, the AIC23B generates this framing signal and sends it to the DSP. In audio slave mode, the signal is generated by the DSP. LRCOUT 28 7 4 I/O I2S ADC-word clock signal. In audio master mode, the AIC23B generates this framing signal and sends it to the DSP. In audio slave mode, the signal is generated by the DSP. MICBIAS 7 17 14 O Buffered low-noise-voltage output suitable for electret-microphone-capsule biasing. Voltage level is 3/4 AVDD nominal. MICIN 8 18 15 I Buffered amplifier input suitable for use with electret-microphone capsules. Without external resistors a default gain of 5 is provided. See Section 2.3.1.2 for details. MODE 13 22 19 I Serial-interface-mode input. See Section 3.1 for details. NC 1, 9 Not Used—No internal connection 17, 25 RHPOUT 31 10 7 O Right stereo mixer-channel amplified headphone output. Nominal 0-dB output level is 1 VRMS. Gain of −73 dB to 6 dB is provided in 1-dB steps. RLINEIN 10 19 16 I Right stereo-line input channel. Nominal 0-dB input level is 1 VRMS. Gain of –34.5 dB to 12 dB is provided in 1.5-dB steps. ROUT 3 13 10 O Right stereo mixer-channel line output. Nominal output level is 1.0 VRMS. 1−5

1.5 Terminal Functions (continued) TERMINAL NO. II//OO DDEESSCCRRIIPPTTIIOONN NAME GQE/ PW RHD ZQE SCLK 15 24 21 I Control-port serial-data clock. For SPI and 2-wire control modes this is the serial-clock input. See Section 3.1 for details. SDIN 14 23 20 I Control-port serial-data input. For SPI and 2-wire control modes this is the serial-data input and also is used to select the control protocol after reset. See Section 3.1 for details. VMID 6 16 13 I Midrail voltage decoupling input. 10-µF and 0.1-µF capacitors should be connected in parallel to this terminal for noise filtering. Voltage level is 1/2 AVDD nominal. XTI/MCLK 16 25 22 I Crystal or external-clock input. Used for derivation of all internal clocks on the AIC23B. XTO 18 26 23 O Crystal output. Connect to external crystal for applications where the AIC23B is the audio timing master. Not used in applications where external clock source is used. 1−6

2 Specifications 2.1 Absolute Maximum Ratings Over Operating Free-Air Temperature Range (unless otherwise noted)† Supply voltage range, AV to AGND, DV to DGND, BV to DGND, HPV to HPGND DD DD DD DD (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to + 3.63 V Analog supply return to digital supply return, AGND to DGND . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to + 3 .63 V Input voltage range, all input signals: Digital . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to DVDD + 0.3 V Analog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to AVDD + 0.3 V Case temperature for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 240°C Operating free-air temperature range, T Commercial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −10°C to 70°C A: Industrial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −40°C to 85°C Storage temperature range, T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C stg †Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTE 1: DVDD may not exceed BVDD + 0.3V; BVDD may not exceed AVDD + 0.3V or HPVDD + 0.3. 2.2 Recommended Operating Conditions MIN NOM MAX UNIT Analog supply voltage, AVDD, HPVDD (see Note 2) 2.7 3.3 3.6 V Digital buffer supply voltage, BVDD (see Note 2) 2.7 3.3 3.6 V Digital core supply voltage, DVDD (see Note 2) 1.42 1.5 3.6 V Analog input voltage, full scale − 0dB (AVDD = 3.3 V) 1 VRMS Stereo-line output load resistance 10 kΩ Headphone-amplifier output load resistance 0 Ω CLKOUT digital output load capacitance 20 pF All other digital output load capacitance 10 pF Stereo-line output load capacitance 50 pF XTI master clock Input 18.43 MHz ADC or DAC conversion rate 96 kHz Commercial −10 70 OOppeerraattiinngg ffrreeee--aaiirr tteemmppeerraattuurree,, TTAA °°CC Industrial −40 85 NOTE 2: Digital voltage values are with respect to DGND; analog voltage values are with respect to AGND. 2−1

2.3 Electrical Characteristics Over Recommended Operating Conditions, AV , DD HPV , BV = 3.3 V, DV = 1.5 V, Slave Mode, XTI/MCLK = 256fs, f = 48 kHz DD DD DD s (unless otherwise stated) 2.3.1 ADC 2.3.1.1 Line Input to ADC PARAMETER TEST CONDITIONS MIN TYP MAX UNIT Input signal level (0 dB) 1 VRMS SSiiggnnaall--ttoo--nnooiissee rraattiioo,, AA--wweeiigghhtteedd,, 00--ddBB ggaaiinn ((sseeee NNootteess 33 fs = 48 kHz (3.3 V) 85 90 ddBB and 4) fs = 48 kHz (2.7 V) 90 DDyynnaammiicc rraannggee,, AA--wweeiigghhtteedd,, −−6600--ddBB ffuullll--ssccaallee iinnppuutt ((sseeee AVDD = 3.3 V 85 90 ddBB Note 4) AVDD = 2.7 V 90 AVDD = 3.3 V –80 TToottaall hhaarrmmoonniicc ddiissttoorrttiioonn,, −−11--ddBB iinnppuutt,, 00--ddBB ggaaiinn ddBB AVDD = 2.7 V 80 Power supply rejection ratio 1 kHz, 100 mVpp 50 dB ADC channel separation 1 kHz input tone 90 dB Programmable gain 1 kHz input tone, RSOURCE < 50 Ω –34.5 12 dB Programmable gain step size Monotonic 1.5 dB Mute attenuation 0 dB, 1 kHz input tone 80 dB 12 dB Input gain 10 20 IInnppuutt rreessiissttaannccee kkΩΩ 0 dB input gain 30 35 Input capacitance 10 pF NOTES: 3. Ratio of output level with 1-kHz full-scale input, to the output level with the input short circuited, measured A-weighted over a 20-Hz to 20-kHz bandwidth using an audio analyzer. 4. All performance measurements done with 20-kHz low-pass filter and, where noted, A-weighted filter. Failure to use such a filter results in higher THD + N and lower SNR and dynamic range readings than shown in the Electrical Characteristics. The low-pass filter removes out-of-band noise, which, although not audible, may affect dynamic specification values. 2.3.1.2 Microphone Input to ADC, 0-dB Gain, f = 8 kHz (40-KΩ Source Impedance, see Section 1.2, s Functional Block Diagram) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT Input signal level (0 dB) 1.0 VRMS AVDD = 3.3 V 80 85 SSiiggnnaall--ttoo--nnooiissee rraattiioo,, AA--wweeiigghhtteedd,, 00--ddBB ggaaiinn ((sseeee NNootteess 33 aanndd 44)) ddBB AVDD = 2.7 V 84 AVDD = 3.3 V 80 85 DDyynnaammiicc rraannggee,, AA--wweeiigghhtteedd,, −−6600--ddBB ffuullll--ssccaallee iinnppuutt ((sseeee NNoottee 44)) ddBB AVDD = 2.7 V 84 AVDD = 3.3 V –60 TToottaall hhaarrmmoonniicc ddiissttoorrttiioonn,, −−11--ddBB iinnppuutt,, 00--ddBB ggaaiinn ddBB AVDD = 2.7 V −60 Power supply rejection ratio 1 kHz, 100 mVpp 50 dB Programmable gain boost 1 kHz input tone, RSOURCE < 50 Ω 20 dB Microphone-path gain MICBOOST = 0, RSOURCE < 50 Ω 14 dB Mute attenuation 0 dB, 1 kHz input tone 60 80 dB Input resistance 8 14 kΩ Input capacitance 10 pF NOTES: 3. Ratio of output level with 1-kHz full-scale input, to the output level with the input short circuited, measured A-weighted over a 20-Hz to 20-kHz bandwidth using an audio analyzer. 4. All performance measurements done with 20-kHz low-pass filter and, where noted, A-weighted filter. Failure to use such a filter results in higher THD + N and lower SNR and dynamic range readings than shown in the Electrical Characteristics. The low-pass filter removes out-of-band noise, which, although not audible, may affect dynamic specification values. 2−2

2.3.1.3 Microphone Bias PARAMETER TEST CONDITIONS MIN TYP MAX UNIT Bias voltage 3/4 AVDD − 100 m 3/4 AVDD 3/4 AVDD + 100 m V Bias-current source 3 mA Output noise voltage 1 kHz to 20 kHz 25 nV/√Hz 2.3.2 DAC 2.3.2.1 Line Output, Load = 10 kΩ, 50 pF PARAMETER TEST CONDITIONS MIN TYP MAX UNIT 0-dB full-scale output voltage (FFFFFF) 1.0 VRMS AVDD = 3.3 V fs = 48kHz 90 100 SSiiggnnaall--ttoo--nnooiissee rraattiioo,, AA--wweeiigghhtteedd,, 00--ddBB ggaaiinn ((sseeee NNootteess 33,, 44,, aanndd 55)) ddBB AVDD = 2.7 V fs = 48 kHz 100 AVDD = 3.3 V 85 90 DDyynnaammiicc rraannggee,, AA--wweeiigghhtteedd ((sseeee NNoottee 44)) ddBB AVDD = 2.7 V TBD 1 kHz, 0 dB –88 –80 AAVVDDDD == 33..33 VV ddBB 1 kHz, −3 dB −92 −86 TToottaall hhaarrmmoonniicc ddiissttoorrttiioonn 1 kHz, 0 dB −85 AAVVDDDD == 22..77 VV ddBB 1 kHz, −3 dB −88 Power supply rejection ratio 1 kHz, 100 mVpp 50 dB DAC channel separation 100 dB NOTES: 3. Ratio of output level with 1-kHz full-scale input, to the output level with the input short circuited, measured A-weighted over a 20-Hz to 20-kHz bandwidth using an audio analyzer. 4. All performance measurements done with 20-kHz low-pass filter and, where noted, A-weighted filter. Failure to use such a filter results in higher THD + N and lower SNR and dynamic range readings than shown in the Electrical Characteristics. The low-pass filter removes out-of-band noise, which, although not audible, may affect dynamic specification values. 5. Ratio of output level with 1-kHz full-scale input, to the output level with all zeros into the digital input, measured A-weighted over a 20-Hz to 20-kHz bandwidth. 2.3.3 Analog Line Input to Line Output (Bypass) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT 0-dB full-scale output voltage 1.0 VRMS AVDD = 3.3 V 90 95 SSiiggnnaall--ttoo--nnooiissee rraattiioo,, AA--wweeiigghhtteedd,, 00--ddBB ggaaiinn ((sseeee NNootteess 33 aanndd 44)) ddBB AVDD = 2.7 V 95 1 kHz, 0 dB –86 –80 AAVVDDDD == 33..33 VV ddBB 1 kHz, −3 dB −92 −86 TToottaall hhaarrmmoonniicc ddiissttoorrttiioonn 1 kHz, 0 dB −86 AAVVDDDD == 22..77 VV ddBB 1 kHz, −3 dB −92 Power supply rejection ratio 1 kHz, 100 mVpp 50 dB DAC channel separation (left to right) 1 kHz, 0 dB 80 dB NOTES: 3. Ratio of output level with 1-kHz full-scale input, to the output level with the input short circuited, measured A-weighted over a 20-Hz to 20-kHz bandwidth using an audio analyzer. 4. All performance measurements done with 20-kHz low-pass filter and, where noted, A-weighted filter. Failure to use such a filter results in higher THD + N and lower SNR and dynamic range readings than shown in the Electrical Characteristics. The low-pass filter removes out-of-band noise, which, although not audible, may affect dynamic specification values. 2−3

2.3.4 Stereo Headphone Output PARAMETER TEST CONDITIONS MIN TYP MAX UNIT 0-dB full-scale output voltage 1.0 VRMS Maximum output power, PO RL = 32 Ω 30 mmWW RL = 16 Ω 40 Signal-to-noise ratio, A-weighted (see Note 4) AVDD = 3.3 V 90 97 dB AAVVDDDD == 33..33 VV,, PO = 10 mW 0.1 TToottaall hhaarrmmoonniicc ddiissttoorrttiioonn %% 1 kHz output PO = 20 mW 1.0 Power supply rejection ratio 1 kHz, 100 mVpp 50 dB Programmable gain 1 kHz output −73 6 dB Programmable-gain step size 1 dB Mute attenuation 1 kHz output 80 dB NOTE 4: All performance measurements done with 20-kHz low-pass filter and, where noted, A-weighted filter. Failure to use such a filter results in higher THD + N and lower SNR and dynamic range readings than shown in the Electrical Characteristics. The low-pass filter removes out-of-band noise, which, although not audible, may affect dynamic specification values. 2.3.5 Analog Reference Levels PARAMETER MIN TYP MAX UNIT Reference voltage AVDD/2 − 50 mV AVDD/2 + 50 mV V Divider resistance 40 50 60 kΩ 2.3.6 Digital I/O PARAMETER MIN TYP MAX UNIT VIL Input low level 0.3 × BVDD V VIH Input high level 0.7 × BVDD V VOL Output low level 0.1 × BVDD V VOH Output high level 0.9 × BVDD V 2.3.7 Supply Current PARAMETER TEST CONDITIONS MIN TYP MAX UNIT Record and playback (all active) 20 24 26 Record and playback (osc, clk, and MIC output powered down) 16 18 20 Line playback only 6 7.5 9 TToottaall ssuuppppllyy ccuurrrreenntt,, IITTOOTT NNoo iinnppuutt ssiiggnnaall Record only 11 13.5 15 mmAA Analog bypass (line in to line out) 4 4.5 6 PPoowweerr ddoowwnn,, DDVVDDDD == 11..55 VV,, Oscillator enabled 0.8 1.5 3 AVDD = BVDD = HPVDD = 3.3 V Oscillator disabled 0.01 2−4

2.4 Digital-Interface Timing PARAMETER MIN TYP MAX UNIT tw(1) High 18 SSyysstteemm--cclloocckk ppuullssee dduurraattiioonn,, MMCCLLKK//XXTTII nnss tw(2) Low 18 tc(1) System-clock period, MCLK/XTI 54 ns Duty cycle, MCLK/XTI 40/60% 60/40% tpd(1) Propagation delay, CLKOUT 0 10 ns tc(1) tw(1) tw(2) MCLK/XTI tpd(1) CLKOUT CLKOUT (Div 2) Figure 2−1. System-Clock Timing Requirements 2.4.1 Audio Interface (Master Mode) PARAMETER MIN TYP MAX UNIT tpd(2) Propagation delay, LRCIN/LRCOUT 0 10 ns tpd(3) Propagation delay, DOUT 0 10 ns tsu(1) Setup time, DIN 10 ns th(1) Hold time, DIN 10 ns BCLK tpd(2) LRCIN LRCOUT tpd(3) DOUT DIN tsu(1) th(1) Figure 2−2. Master-Mode Timing Requirements 2−5

2.4.2 Audio Interface (Slave-Mode) PARAMETER MIN TYP MAX UNIT tw(3) High 20 PPuullssee dduurraattiioonn,, BBCCLLKK nnss tw(4) Low 20 tc(2) Clock period, BCLK 50 ns tpd(4) Propagation delay, DOUT 0 10 ns tsu(2) Setup time, DIN 10 ns th(2) Hold time, DIN 10 ns tsu(3) Setup time, LRCIN 10 ns th(3) Hold time, LRCIN 10 ns tc(2) tw(4) tw(3) BCLK LRCIN LRCOUT tsu(2) th(3) tsu(3) DIN tpd(2) th(2) DOUT Figure 2−3. Slave-Mode Timing Requirements 2−6

2.4.3 Three-Wire Control Interface (SDIN) PARAMETER MIN TYP MAX UNIT tw(5) High 20 CClloocckk ppuullssee dduurraattiioonn,, SSCCLLKK nnss tw(6) Low 20 tc(3) Clock period, SCLK 80 ns tsu(4) Clock rising edge to CS rising edge, SCLK 60 ns tsu(5) Setup time, SDIN to SCLK 20 ns th(4) Hold time, SCLK to SDIN 20 ns tw(7) High 20 PPuullssee dduurraattiioonn,, CCSS nnss tw(8) Low 20 tw(8) CS tc(3) tw(5) tw(6) tsu(4) SCLK tsu(5) th(4) DIN LSB Figure 2−4. Three-Wire Control Interface Timing Requirements 2.4.4 Two-Wire Control Interface PARAMETER MIN TYP MAX UNIT tw(9) High 1.3 µs CClloocckk ppuullssee dduurraattiioonn,, SSCCLLKK tw(10) Low 600 ns f(sf) Clock frequency, SCLK 0 400 kHz th(5) Hold time (start condition) 600 ns tsu(6) Setup time (start condition) 600 ns th(6) Data hold time 900 ns tsu(7) Data setup time 100 ns tr Rise time, SDIN, SCLK 300 ns tf Fall time, SDIN, SCLK 300 ns tsu(8) Setup time (stop condition) 600 ns tsp Pulse width of spikes suppressed by input filter 0 50 ns tw(9) tw(10) tsp SCLK th(5) th(6) tsu(7) tsu(8) DIN Figure 2−5. Two-Wire Control Interface Timing Requirements 2−7

2−8

3 How to Use the TLV320AIC23B 3.1 Control Interfaces The TLV320AIC23B has many programmable features. The control interface is used to program the registers of the device. The control interface complies with SPI (three-wire operation) and two-wire operation specifications. The state of the MODE terminal selects the control interface type. The MODE pin must be hardwired to the required level. MODE INTERFACE 0 2-wire 1 SPI 3.1.1 SPI In SPI mode, SDIN carries the serial data, SCLK is the serial clock and CS latches the data word into the TLV320AIC23B. The interface is compatible with microcontrollers and DSPs with an SPI interface. A control word consists of 16 bits, starting with the MSB. The data bits are latched on the rising edge of SCLK. A rising edge on CS after the 16th rising clock edge latches the data word into the AIC (see Figure 3-1). The control word is divided into two parts. The first part is the address block, the second part is the data block: B[15:9] Control Address Bits B[8:0] Control Data Bits ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ CS SCLK SDIN B15 B14 B13 B12 B11 B10 B9 B8 B7 B6 B5 B4 B3 B2 B1 B0 MSB LSB Figure 3−1. SPI Timing 3.1.2 2-Wire In 2-wire mode, the data transfer uses SDIN for the serial data and SCLK for the serial clock. The start condition is a falling edge on SDIN while SCLK is high. The seven bits following the start condition determine which device on the 2-wire bus receives the data. R/W determines the direction of the data transfer. The TLV320AIC23B is a write only device and responds only if R/W is 0. The device operates only as a slave device whose address is selected by setting the state of the CS pin as follows. CS STATE ADDRESS (Default = 0) 0 0011010 1 0011011 3−1

The device that recognizes the address responds by pulling SDIN low during the ninth clock cycle, acknowledging the data transfer. The control follows in the next two eight-bit blocks. The stop condition after the data transfer is a rising edge on SDIN when SCLK is high (see Figure 3-2). The 16-bit control word is divided into two parts. The first part is the address block, the second part is the data block: B[15:9] Control Address Bits B[8:0] Control Data Bits Start Stop SCLK 1 7 8 9 1 8 9 1 8 9 SDI ADDR R/W ACK B15 − B8 ACK B7 − B0 ACK Figure 3−2. 2-Wire Compatible Timing 3.1.3 Register Map The TLV320AIC23B has the following set of registers, which are used to program the modes of operation. ADDRESS REGISTER 0000000 Left line input channel volume control 0000001 Right line input channel volume control 0000010 Left channel headphone volume control 0000011 Right channel headphone volume control 0000100 Analog audio path control 0000101 Digital audio path control 0000110 Power down control 0000111 Digital audio interface format 0001000 Sample rate control 0001001 Digital interface activation 0001111 Reset register Left line input channel volume control (Address: 0000000) BIT D8 D7 D6 D5 D4 D3 D2 D1 D0 Function LRS LIM X X LIV4 LIV3 LIV2 LIV1 LIV0 Default 0 1 0 0 1 0 1 1 1 LRS Left/right line simultaneous volume/mute update Simultaneous update 0 = Disabled 1 = Enabled LIM Left line input mute 0 = Normal 1 = Muted LIV[4:0] Left line input volume control (10111 = 0 dB default) 11111 = +12 dB down to 00000 = –34.5 dB in 1.5-dB steps X Reserved 3−2

Right Line Input Channel Volume Control (Address: 0000001) BIT D8 D7 D6 D5 D4 D3 D2 D1 D0 Function RLS RIM X X RIV4 RIV3 RIV2 RIV1 RIV0 Default 0 1 0 0 1 0 1 1 1 RLS Right/left line simultaneous volume/mute update Simultaneous update 0 = Disabled 1 = Enabled RIM Right line input mute 0 = Normal 1 = Muted RIV[4:0] Right line input volume control (10111 = 0 dB default) 11111 = +12 dB down to 00000 = –34.5 dB in 1.5-dB steps X Reserved Left Channel Headphone Volume Control (Address: 0000010) BIT D8 D7 D6 D5 D4 D3 D2 D1 D0 Function LRS LZC LHV6 LHV5 LHV4 LHV3 LHV2 LHV1 LHV0 Default 0 1 1 1 1 1 0 0 1 LRS Left/right headphone channel simultaneous volume/mute update Simultaneous update 0 = Disabled 1 = Enabled LZC Left-channel zero-cross detect Zero-cross detect 0 = Off 1 = On LHV[6:0] Left Headphone volume control (1111001 = 0 dB default) 1111111 = +6 dB, 79 steps between +6 dB and −73 dB (mute), 0110000 = −73 dB (mute), any thing below 0110000 does nothing − you are still muted Right Channel Headphone Volume Control (Address: 0000011) BIT D8 D7 D6 D5 D4 D3 D2 D1 D0 Function RLS RZC RHV6 RHV5 RHV4 RHV3 RHV2 RHV1 RHV0 Default 0 1 1 1 1 1 0 0 1 RLS Right/left headphone channel simultaneous volume/mute Update Simultaneous update 0 = Disabled 1 = Enabled RZC Right-channel zero-cross detect Zero-cross detect 0 = Off 1 = On RHV[6:0] Right headphone volume control (1111001 = 0 dB default) 1111111 = +6 dB, 79 steps between +6 dB and −73 dB (mute), 0110000 = −73 dB (mute), any thing below 0110000 does nothing − you are still muted Analog Audio Path Control (Address: 0000100) BIT D8 D7 D6 D5 D4 D3 D2 D1 D0 Function STA2 STA1 STA0 STE DAC BYP INSEL MICM MICB Default 0 0 0 0 0 1 0 1 0 STA[2:0] and STE STE STA2 STA1 STA0 ADDED SIDETONE 1 1 X X 0 dB 1 0 0 0 −6 dB 1 0 0 1 −9 dB 1 0 1 0 −12 dB 1 0 1 1 −18 dB 0 X X X Disabled DAC DAC select 0 = DAC off 1 = DAC selected BYP Bypass 0 = Disabled 1 = Enabled 3−3

INSEL Input select for ADC 0 = Line 1 = Microphone MICM Microphone mute 0 = Normal 1 = Muted MICB Microphone boost 0=dB 1 = 20dB X Reserved Digital Audio Path Control (Address: 0000101) BIT D8 D7 D6 D5 D4 D3 D2 D1 D0 Function X X X X X DACM DEEMP1 DEEMP0 ADCHP Default 0 0 0 0 0 1 0 0 0 DACM DAC soft mute 0 = Disabled 1 = Enabled DEEMP[1:0] De-emphasis control 00 = Disabled 01 = 32 kHz 10 = 44.1 kHz 11 = 48 kHz ADCHP ADC high-pass filter 1 = Disabled 0 = Enabled X Reserved Power Down Control (Address: 0000110) BIT D8 D7 D6 D5 D4 D3 D2 D1 D0 Function X OFF CLK OSC OUT DAC ADC MIC LINE Default 0 0 0 0 0 0 1 1 1 OFF Device power 0 = On 1 = Off CLK Clock 0 = On 1 = Off OSC Oscillator 0 = On 1 = Off OUT Outputs 0 = On 1 = Off DAC DAC 0 = On 1 = Off ADC ADC 0 = On 1 = Off MIC Microphone input 0 = On 1 = Off LINE Line input 0 = On 1 = Off X Reserved Digital Audio Interface Format (Address: 0000111) BIT D8 D7 D6 D5 D4 D3 D2 D1 D0 Function X X MS LRSWAP LRP IWL1 IWL0 FOR1 FOR0 Default 0 0 0 0 0 0 0 0 1 MS Master/slave mode 0 = Slave 1 = Master LRSWAP DAC left/right swap 0 = Disabled 1 = Enabled LRP DAC left/right phase 0 = Right channel on, LRCIN high 1 = Right channel on, LRCIN low DSP mode 1 = MSB is available on 2nd BCLK rising edge after LRCIN rising edge 0 = MSB is available on 1st BCLK rising edge after LRCIN rising edge IWL[1:0] Input bit length 00 = 16 bit 01 = 20 bit 10 = 24 bit 11 = 32 bit FOR[1:0] Data format 11 = DSP format, frame sync followed by two data words 10 = I2S format, MSB first, left – 1 aligned 01 = MSB first, left aligned 00 = MSB first, right aligned X Reserved NOTES: 1. In Master mode, the TLV320AIC23B supplies the BCLK, LRCOUT, and LRCIN. In Slave mode, BCLK, LRCOUT, and LRCIN are supplied to the TLV320AIC23B. 2. In normal mode, BCLK = MCLK/4 for all sample rates except for 88.2 kHz and 96 kHz. For 88.2 kHz and 96 kHz sample rate, BCLK = MCLK. 3. In USB mode, bit BCLK = MCLK 3−4

Sample Rate Control (Address: 0001000) BIT D8 D7 D6 D5 D4 D3 D2 D1 D0 Function X CLKOUT CLKIN SR3 SR2 SR1 SR0 BOSR USB/Normal Default 0 0 0 1 0 0 0 0 0 CLKIN Clock input divider 0 = MCLK 1 = MCLK/2 CLKOUT Clock output divider 0 = MCLK 1 = MCLK/2 SR[3:0] Sampling rate control (see Sections 3.3.2.1 AND 3.3.2.2) BOSR Base oversampling rate USB mode: 0 = 250 f 1 = 272 f s s Normal mode: 0 = 256 f 1 = 384 f s s USB/Normal Clock mode select: 0 = Normal 1 = USB X Reserved Digital Interface Activation (Address: 0001001) BIT D8 D7 D6 D5 D4 D3 D2 D1 D0 Function X RES RES X X X X X ACT Default 0 0 0 0 0 0 0 0 0 ACT Activate interface 0 = Inactive 1 = Active X Reserved Reset Register (Address: 0001111) BIT D8 D7 D6 D5 D4 D3 D2 D1 D0 Function RES RES RES RES RES RES RES RES RES Default 0 0 0 0 0 0 0 0 0 RES Write 000000000 to this register triggers reset 3.2 Analog Interface 3.2.1 Line Inputs The TLV320AIC23B has line inputs for the left and the right audio channels (RLINEIN and LLINEIN). Both line inputs have independently programmable volume controls and mutes. Active and passive filters for the two channels prevent high frequencies from folding back into the audio band. The line-input gain is logarithmically adjustable from 12 dB to –34.5 dB in 1.5-dB steps. The ADC full-scale range is 1.0 V at AV = 3.3 V. The full-scale range tracks linearly with analog supply voltage AV . To avoid distortions, RMS DD DD it is important not to exceed the full-scale range. The gain is independently programmable on both left and right line-inputs. To reduce the number of software write cycles required. Both channels can be locked to the same value by setting the RLS and LRS bits (see Section 3.1.3). The line inputs are biased internally to VMID. When the line inputs are muted or the device is set to standby mode, the line inputs are kept biased to VMID using special antithump circuitry. This reduces audible clicks that otherwise might be heard when reactivating the inputs. For interfacing to a CD system, the line input should be scaled to 1 V to avoid clipping, using the circuit shown RMS in Figure 3-3. Where: R1 C2 + CDIN LINEIN R1 = 5 kΩ R2 = 5 kΩ C1 = 47 pF R C1 C2 = 470 nF 2 AGND Figure 3−3. Analog Line Input Circuit R1 and R2 divide the input signal by two, reducing the 2 V from the CD player to the nominal 1 V of the AIC23B RMS RMS inputs. C1 filters high-frequency noise, and C2 removes any dc component from the signal. 3−5

3.2.2 Microphone Input MICIN is a high-impedance, low-capacitance input that is compatible with a wide range of microphones. It has a programmable volume control and a mute function. Active and passive filters prevent high frequencies from folding back into the audio band. The MICIN signal path has two gain stages. The first stage has a nominal gain of G1 = 50 k/10 k = 5. By adding an external resistor (R ) in series with MICIN, the gain of the first stage can be adjusted by G1 = 50 k/(10 k + R ). MIC MIC For example, R = 40 k gives a gain of 0 dB. The second stage has a software programmable gain of 0 dB or 20 MIC dB (see Section 3.1.3). 50 kΩ 10 kΩ MICIN To ADC VMID 0 dB/20 dB Figure 3−4. Microphone Input Circuit The microphone input is biased internally to VMID. When the line inputs are muted, the MICIN input is kept biased to VMID using special antithump circuitry. This reduces audible clicks that may otherwise be heard when reactivating the input. The MICBIAS output provides a low-noise reference voltage suitable for biasing electret type microphones and the associated external resistor biasing network. The maximum source current capability is 3 mA. This limits the smallest value of external biasing resistors that safely can be used. The MICBIAS output is not active in standby mode. 3.2.3 Line Outputs The TLV320AIC23B has two low-impedance line outputs (LLINEOUT and RLINEOUT) capable of driving line loads with 10-kΩ and 50-pF impedances. The DAC full-scale output voltage is 1.0 V at AV = 3.3 V. The full-scale range tracks linearly with the analog RMS DD supply voltage AV The DAC is connected to the line outputs via a low-pass filter that removes out-of-band DD. components. No further external filtering is required in most applications. The DAC outputs, line inputs, and the microphone signal are summed into the line outputs. These sources can be switched off independently. For example, in bypass mode, the line inputs are routed to the line outputs, bypassing the ADC and the DAC. If sidetone is enabled, the microphone signal is routed to both line outputs via a four-step programmable attenuation circuit. The line outputs are muted by either muting the DAC (analog) or soft muting (digital) and disabling the bypass and sidetone paths (see Section 3.1.3). 3.2.4 Headphone Output The TLV320AIC23B has stereo headphone outputs (LHPOUT and RHPOUT), and is designed to drive 16-Ω or 32-Ω headphones. The headphone output includes a high-quality volume control and mute function. The headphone volume is logarithmically adjustable from 6 dB to –73 dB in 1-dB steps. Writing 000000 to the volume-control registers (see Section 3.1.3) mutes the headphone output. When the headphone output is muted or the device is placed in standby mode, the dc voltage is maintained at the outputs to prevent audible clicks. A zero-cross detection circuit is provided under the control of the LZC and RZC bits. If this circuit is enabled, the volume-control values are updated only when the input signal to the gain stage is close to the analog ground level. 3−6

This minimizes audible clicks as the volume is changed or the device is muted. This circuit has no time-out, so, if only dc levels are being applied to the gain stage input of more than 20 mV, the gain is not updated. The gain is independently programmable on the left and right channels. Both channels can be locked to the same value by setting the RLS and LRS bits (see Section 3.1.3). 3.2.5 Analog Bypass Mode The TLV320AIC23B includes a bypass mode in which the analog line inputs are directly routed to the analog line outputs, bypassing the ADC and DAC. This is enabled by selecting the bypass bit in the analog audio path control register[see Section 3.1.3). For a true bypass mode, the output from the DAC and the sidetone should be disabled. The line input and headphone output volume controls and mutes are still operational in bypass mode. Therefore the line inputs, DAC output, and microphone input can be summed together. The maximum signal at any point in the bypass path must be no greater than 1.0V at AV =3.3V to avoid clipping and distortion. This amplitude tracks linearly with AV . rms DD DD 3.2.6 Sidetone Insertion The TLV320AIC23B has a sidetone insertion made where the microphone input is routed to the line and headphone outputs. This is useful for telephony and headset applications. The attenuation of the sidetone signal may be set to −6 dB, −9 dB, −12 dB, −15 dB, or 0dB, by software selection (see Section 3.1.3). If this mode is used to sum the microphone input with the DAC output and line inputs, care must be taken not to exceed signal level to avoid clipping and distortion. 3.3 Digital Audio Interface 3.3.1 Digital Audio-Interface Modes The TLV320AIC23B supports four audio-interface modes. • Right justified • Left justified • I2S mode • DSP mode The four modes are MSB first and operate with a variable word width between 16 to 32 bits (except right-justified mode, which does not support 32 bits). The digital audio interface consists of clock signal BCLK, data signals DIN and DOUT, and synchronization signals LRCIN and LRCOUT. BCLK is an output in master mode and an input in slave mode. 3.3.1.1 Right-Justified Mode In right-justified mode, the LSB is available on the rising edge of BCLK, preceding a falling edge on LRCIN or LRCOUT (see Figure 3-5). 1/fs LRCIN/ LRCOUT BCLK Left Channel Right Channel DIN/ 0 n n−1 1 0 n n−1 1 0 DOUT MSB LSB Figure 3−5. Right-Justified Mode Timing 3.3.1.2 Left-Justified Mode In left-justified mode, the MSB is available on the rising edge of BCLK, following a rising edge on LRCIN or LRCOUT (see Figure 3-6) 3−7

1/fs LRCIN/ LRCOUT BCLK Left Channel Right Channel DIN/ n n−1 1 0 n n−1 1 0 n DOUT MSB LSB Figure 3−6. Left-Justified Mode Timing 3.3.1.3 I2S Mode In I2S mode, the MSB is available on the second rising edge of BCLK, after the falling edge on LRCIN or LRCOUT (see Figure 3-7). 1/fs LRCIN/ LRCOUT BCLK 1BCLK Left Channel Right Channel DIN/ n n−1 1 0 n n−1 1 0 DOUT MSB LSB Figure 3−7. I2S Mode Timing 3.3.1.4 DSP Mode The DSP mode is compatible with the McBSP ports of TI DSPs. LRCIN and LRCOUT must be connected to the Frame Sync signal of the McBSP. A falling edge on LRCIN or LRCOUT starts the data transfer. The left-channel data consists of the first data word, which is immediately followed by the right channel data word (see Figure 3-8). Input word length is defined by the IWL register. Figure 3−8 shows LRP = 1 (default LRP = 0). LRCIN/ LRCOUT BCLK Left Channel Right Channel DIN/ n n−1 1 0 n n−1 1 0 DOUT MSB LSB MSB LSB Figure 3−8. DSP Mode Timing 3−8

3.3.2 Audio Sampling Rates The TLV320AIC23B can operate in master or slave clock mode. In the master mode, the TLV320AIC23B clock and sampling rates are derived from a 12-MHz MCLK signal. This 12-MHz clock signal is compatible with the USB specification. The TLV320AIC23B can be used directly in a USB system. In the slave mode, an appropriate MCLK or crystal frequency and the sample rate control register settings control the TLV320AIC23B clock and sampling rates. The settings in the sample rate control register control the clock mode and sampling rates. Sample Rate Control (Address: 0001000) BIT D8 D7 D6 D5 D4 D3 D2 D1 D0 Function X CLKOUT CLKIN SR3 SR2 SR1 SR0 BOSR USB/Nor- mal Default 0 0 0 1 0 0 0 0 0 CLKOUT Clock output divider 0 = MCLK 1 = MCLK/2 CLKIN Clock input divider 0 = MCLK 1 = MCLK/2 SR[3:0] Sampling rate control (see Sections 3.3.2.1 and 3.3.2.2) BOSR Base oversampling rate USB mode: 0 = 250 f 1 = 272 f s s Normal mode: 0 = 256 f 1 = 384 f s s USB/Normal Clock mode select: 0 = Normal 1 = USB X Reserved The clock circuit of the AIC23B has two internal dividers. The first, controlled by CLKIN, applies to the sampling-rate generator of the codec. The second, controlled by CLKOUT, applies only to the CLKOUT terminal. By setting CLKIN to 1, the entire codec is clocked with half the frequency, effectively dividing the resulting sampling rates by two. The following sampling-rate tables are based on CLKIN = MCLK. 3.3.2.1 USB-Mode Sampling Rates (MCLK = 12 MHz) In the USB mode, the following ADC and DAC sampling rates are available: SAMPLING RATE† SSAAMMPPLLIINNGG--RRAATTEE CCOONNTTRROOLL SSEETTTTIINNGGSS AADDCC DDAACC FFIILLTTEERR TTYYPPEE (kHz) (kHz) SR3 SR2 SR1 SR0 BOSR 96 96 3 0 1 1 1 0 88.2 88.2 2 1 1 1 1 1 48 48 0 0 0 0 0 0 44.1 44.1 1 1 0 0 0 1 32 32 0 0 1 1 0 0 8.021 8.021 1 1 0 1 1 1 8 8 0 0 0 1 1 0 48 8 0 0 0 0 1 0 44.1 8.021 1 1 0 0 1 1 8 48 0 0 0 1 0 0 8.021 44.1 1 1 0 1 0 1 †The sampling rates are derived from the 12-MHz master clock. The available oversampling rates do not produce exactly 8-kHz, 44.1-kHz, and 88.2-kHz sampling rates, but 8.021 kHz, 44.117 kHz, and 88.235 kHz, respectively. See Figures 3−17 through 3−34 for filter responses 3−9

3.3.2.2 Normal-Mode Sampling Rates In normal mode, the following ADC and DAC sampling rates, depending on the MCLK frequency, are available: MCLK = 12.288 MHz SAMPLING RATE SSAAMMPPLLIINNGG--RRAATTEE CCOONNTTRROOLL SSEETTTTIINNGGSS AADDCC DDAACC FFIILLTTEERR TTYYPPEE (kHz) (kHz) SR3 SR2 SR1 SR0 BOSR 96 96 2 0 1 1 1 0 48 48 1 0 0 0 0 0 32 32 1 0 1 1 0 0 8 8 1 0 0 1 1 0 48 8 1 0 0 0 1 0 8 48 1 0 0 1 0 0 MCLK = 11.2896 MHz SAMPLING RATE SSAAMMPPLLIINNGG--RRAATTEE CCOONNTTRROOLL SSEETTTTIINNGGSS AADDCC DDAACC FFIILLTTEERR TTYYPPEE (kHz) (kHz) SR3 SR2 SR1 SR0 BOSR 88.2 88.2 2 1 1 1 1 0 44.1 44.1 1 1 0 0 0 0 8.021 8.021 1 1 0 1 1 0 44.1 8.021 1 1 0 0 1 0 8.021 44.1 1 1 0 1 0 0 MCLK = 18.432 MHz SAMPLING RATE SSAAMMPPLLIINNGG--RRAATTEE CCOONNTTRROOLL SSEETTTTIINNGGSS AADDCC DDAACC FFIILLTTEERR TTYYPPEE (kHz) (kHz) SR3 SR2 SR1 SR0 BOSR 96 96 2 0 1 1 1 1 48 48 1 0 0 0 0 1 32 32 1 0 1 1 0 1 8 8 1 0 0 1 1 1 48 8 1 0 0 0 1 1 8 48 1 0 0 1 0 1 MCLK = 16.9344 MHz SAMPLING RATE SSAAMMPPLLIINNGG--RRAATTEE CCOONNTTRROOLL SSEETTTTIINNGGSS AADDCC DDAACC FFIILLTTEERR TTYYPPEE (kHz) (kHz) SR3 SR2 SR1 SR0 BOSR 88.2 88.2 2 1 1 1 1 1 44.1 44.1 1 1 0 0 0 1 8.021 8.021 1 1 0 1 1 1 44.1 8.021 1 1 0 0 1 1 8.021 44.1 1 1 0 1 0 1 3−10

3.3.3 Digital Filter Characteristics PARAMETER TEST CONDITIONS MIN TYP MAX UNIT ADC Filter Characteristics ( TI DSP 250 fs Mode Operation ) Passband ±0.05 dB 0.416 fs Hz Stopband −6 dB 0.5 fs Hz Passband ripple ±0.05 dB Stopband attenuation f > 0.584 fs −60 dB ADC Filter Characteristics ( TI DSP 272 fs and Normal Mode Operation ) Passband ±0.05 dB 0.4535 fs Hz Stopband −6 dB 0.5 fs Hz Passband ripple ±0.05 dB Stopband attenuation f > 0.5465 fs −60 dB ADC High-Pass Filter Characteristics −3 dB, fs = 44.1 kHz 3.7 Hz −3 dB, fs = 48 kHz 4.0 Hz −0.5 dB, fs = 44.1 kHz 10.4 Hz CCoorrnneerr ffrreeqquueennccyy −0.5 dB, fs = 48 kHz 11.3 Hz −0.1 dB fs = 44.1 kHz 21.6 Hz −0.1 dB, fs = 48 kHz 23.5 Hz DAC Filter Characteristics (48-kHz Sampling Rate) Passband ±0.03 dB 0.416 fs Hz Stopband −6 dB 0.5 fs Hz Passband ripple ±0.03 dB Stopband attenuation f > 0.584 fs −50 dB DAC Filter Characteristics (44.1-kHz Sampling Rate) Passband ±0.03 dB 0.4535 fs Hz Stopband −6 dB 0.5 fs Hz Passband ripple ±0.03 dB Stopband attenuation f > 0.5465 fs −50 dB 3−11

FILTER RESPONSE vs NORMALIZED AUDIO SAMPLING FREQUENCY 0 −2 B d − e −4 s n o p s e R r −6 e Filt −8 −10 0 0.1 0.2 0.3 0.4 0.5 Normalized Audio Sampling Frequency Figure 3−9. Digital De-Emphasis Filter Response − 44.1 kHz Sampling FILTER RESPONSE vs NORMALIZED AUDIO SAMPLING FREQUENCY 0 −2 B d − e −4 s n o p s e R r −6 e Filt −8 −10 0 0.10 0.20 0.30 0.40 0.50 Normalized Audio Sampling Frequency Figure 3−10. Digital De-Emphasis Filter Response − 48 kHz Sampling 3−12

FILTER RESPONSE vs NORMALIZED AUDIO SAMPLING FREQUENCY 10 B d −10 − e s on −30 p s e R −50 r e Filt −70 −90 0 0.5 1 1.5 2 2.5 3 Normalized Audio Sampling Frequency Figure 3−11. ADC Digital Filter Response 0: USB Mode (Group Delay = 12 Output Samples) FILTER RESPONSE vs NORMALIZED AUDIO SAMPLING FREQUENCY 0.10 0.08 B d 0.06 − e 0.04 s on 0.02 p s 0 e R r −0.02 e Filt −0.04 −0.06 −0.08 −0.10 0 0.05 0.1 0.15 0.2 0.25 0.3 0.35 0.4 0.45 0.5 Normalized Audio Sampling Frequency Figure 3−12. ADC Digital Filter Ripple 0: USB (Group Delay = 20 Output Samples) 3−13

FILTER RESPONSE vs NORMALIZED AUDIO SAMPLING FREQUENCY 10 B d −10 − e s on −30 p s e R r −50 e Filt −70 −90 0 0.5 1 1.5 2 2.5 3 Normalized Audio Sampling Frequency Figure 3−13. ADC Digital Filter Response 1: USB Mode Only FILTER RESPONSE vs NORMALIZED AUDIO SAMPLING FREQUENCY 0.10 0.08 B d 0.06 − e 0.04 s on 0.02 p s 0 e R r −0.02 e Filt −0.04 −0.06 −0.08 −0.10 0 0.05 0.1 0.15 0.2 0.25 0.3 0.35 0.4 0.45 0.5 Normalized Audio Sampling Frequency Figure 3−14. ADC Digital Filter Ripple 1: USB Mode Only 3−14

FILTER RESPONSE vs NORMALIZED AUDIO SAMPLING FREQUENCY 10 B d −10 − e s on −30 p s e R r −50 e Filt −70 −90 0 0.5 1 1.5 2 2.5 3 Normalized Audio Sampling Frequency Figure 3−15. ADC Digital Filter Response 2: USB mode and Normal Modes (Group Delay = 3 Output Samples) FILTER RESPONSE vs NORMALIZED AUDIO SAMPLING FREQUENCY 0.4 B 0.3 d − 0.2 e s n 0.1 o p s 0 e R r −0.1 e Filt −0.2 −0.3 −0.4 0 0.05 0.1 0.15 0.2 0.25 0.3 0.35 0.4 0.45 0.5 Normalized Audio Sampling Frequency Figure 3−16. ADC Digital Filter Ripple 2: USB Mode and Normal Modes 3−15

FILTER RESPONSE vs NORMALIZED AUDIO SAMPLING FREQUENCY 10 B d −10 − e s on −30 p s e R r −50 e Filt −70 −90 0 0.5 1 1.5 2 2.5 3 Normalized Audio Sampling Frequency Figure 3−17. ADC Digital Filter Response 3: USB Mode Only FILTER RESPONSE vs NORMALIZED AUDIO SAMPLING FREQUENCY 0.4 0.3 B d − 0.2 e s n 0.1 o p s 0 e R r −0.1 e Filt −0.2 −0.3 −0.4 0 0.05 0.10 0.15 0.20 0.25 0.30 0.35 0.40 0.45 0.50 Normalized Audio Sampling Frequency Figure 3−18. ADC Digital Filter Ripple 3: USB Mode Only 3−16

FILTER RESPONSE vs NORMALIZED AUDIO SAMPLING FREQUENCY 10 B d −10 − e s on −30 p s e R r −50 e Filt −70 −90 0 0.5 1 1.5 2 2.5 3 Normalized Audio Sampling Frequency Figure 3−19. DAC Digital Filter Response 0: USB Mode FILTER RESPONSE vs NORMALIZED AUDIO SAMPLING FREQUENCY 0.10 0.08 B d 0.06 − e 0.04 s n 0.02 o p s 0 e R −0.02 r e Filt −0.04 −0.06 −0.08 −0.10 0 0.05 0.1 0.15 0.2 0.25 0.3 0.35 0.4 0.45 0.5 Normalized Audio Sampling Frequency Figure 3−20. DAC Digital Filter Ripple 0: USB Mode 3−17

FILTER RESPONSE vs NORMALIZED AUDIO SAMPLING FREQUENCY 10 B d −10 − e s on −30 p s e R r −50 e Filt −70 −90 0 0.5 1 1.5 2 2.5 3 Normalized Audio Sampling Frequency Figure 3−21. DAC Digital Filter Response 1: USB Mode Only FILTER RESPONSE vs NORMALIZED AUDIO SAMPLING FREQUENCY 0.10 0.08 B d 0.06 − e 0.04 s on 0.02 p s 0 e R r −0.02 e Filt −0.04 −0.06 −0.08 −0.10 0 0.05 0.1 0.15 0.2 0.25 0.3 0.35 0.4 0.45 0.5 Normalized Audio Sampling Frequency Figure 3−22. DAC Digital Filter Ripple 1: USB Mode Only 3−18

FILTER RESPONSE vs NORMALIZED AUDIO SAMPLING FREQUENCY 10 B − d −10 e s on −30 p s e R r −50 e Filt −70 −90 0 0.5 1 1.5 2 2.5 3 Normalized Audio Sampling Frequency Figure 3−23. DAC Digital Filter Response 2: USB Mode and Normal Modes FILTER RESPONSE vs NORMALIZED AUDIO SAMPLING FREQUENCY 0.4 B 0.3 d − 0.2 e s n 0.1 o p s 0 e R r −0.1 e Filt −0.2 −0.3 −0.4 0 0.05 0.1 0.15 0.2 0.25 0.3 0.35 0.4 0.45 0.5 Normalized Audio Sampling Frequency Figure 3−24. DAC Digital Filter Ripple 2: USB Mode and Normal Modes 3−19

FILTER RESPONSE vs NORMALIZED AUDIO SAMPLING FREQUENCY 10 B d −10 − e s on −30 p s e R r −50 e Filt −70 −90 0 0.5 1 1.5 2 2.5 3 Normalized Audio Sampling Frequency Figure 3−25. DAC Digital Filter Response 3: USB Mode Only FILTER RESPONSE vs NORMALIZED AUDIO SAMPLING FREQUENCY 0.4 B 0.3 d − 0.2 e s n 0.1 o p s 0 e R r −0.1 e Filt −0.2 −0.3 −0.4 0 0.05 0.1 0.15 0.2 0.25 0.3 0.35 0.4 0.45 0.5 Normalized Audio Sampling Frequency Figure 3−26. DAC Digital Filter Ripple 3: USB Mode Only The delay between the converter is a function of the sample rate. The group delays for the AIC23B are shown in the following table. Each delay is one LR clock (1/sample rate). Table 3−1. Group Dealys FILTER GROUP DELAY DAC type 0 11 DAC type 1 18 DAC type 2 5 DAC type 3 5 ADC type 0 12 ADC type 1 20 ADC type 2 3 ADC type 3 6 3−20

Appendix A Mechanical Data GQE/ZQE (S-PBGA-N80) PLASTIC BALL GRID ARRAY 5,10 SQ 4,00 TYP 4,90 0,50 J H 0 G 5 0, F E D C B A 1 2 3 4 5 6 7 8 9 0,68 0,62 1,00 MAX Seating Plane 0,35 ∅ 0,05 M 0,25 0,21 0,08 0,11 4200461/C 10/00 NOTES: A. All linear dimensions are in millimeters. B. This drawing is subject to change without notice. C. MicroStar Junior BGA configuration D. Falls within JEDEC MO-225 MicroStar Junior is a trademark of Texas Instruments. A−1

PW (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 14 PINS SHOWN 0,30 0,65 0,10 M 0,19 14 8 0,15 NOM 4,50 6,60 4,30 6,20 Gage Plane 0,25 1 7 0°−(cid:1)8° A 0,75 0,50 Seating Plane 0,15 1,20 MAX 0,10 0,05 PINS ** 8 14 16 20 24 28 DIM A MAX 3,10 5,10 5,10 6,60 7,90 9,80 A MIN 2,90 4,90 4,90 6,40 7,70 9,60 4040064/F 01/97 NOTES: A. All linear dimensions are in millimeters. B. This drawing is subject to change without notice. C. Body dimensions do not include mold flash or protrusion not to exceed 0,15. D. Falls within JEDEC MO-153 A−2

RHD (S−PQFP−N28) PLASTIC QUAD FLATPACK A 5,00 B 5,00 ÉÉÉÉÉ ÉÉÉÉÉ ÉÉÉÉÉ 28 ÉÉÉÉÉ 1 PIN 1 INDEX AREA 1,00 0,20 REF 0,80 C SEATING PLANE 0,08 C 3,25 0,05 MAX PIN 1 SQ IDENTIFIER 3,00 28(cid:1)0,65 1 0,45 0,435 28 0,18 0,435 4(cid:1) 3,00 0,18 0,50 EXPOSED THERMAL DIE PAD 28(cid:1)0,30 D 0,18 0,10 M C A B 4204400/A 05/02 NOTES: A. All linear dimensions are in millimeters. B. This drawing is subject to change without notice. C. QFN (Quad Flatpack No−Lead) Package configuration. D. The Package thermal performance may be enhanced by bonding the thermal die pad to an external thermal plane. This pad is electrically and thermally connected to the backside of the die and possibly selected ground leads. E. Package complies to JEDEC MO-220. A−3

PACKAGE OPTION ADDENDUM www.ti.com 21-May-2019 PACKAGING INFORMATION Orderable Device Status Package Type Package Pins Package Eco Plan Lead/Ball Finish MSL Peak Temp Op Temp (°C) Device Marking Samples (1) Drawing Qty (2) (6) (3) (4/5) TLV320AIC23BGQE ACTIVE BGA GQE 80 360 TBD SNPB Level-2A-235C-4 WKS -10 to 70 AIC23BG MICROSTAR JUNIOR TLV320AIC23BIGQE LIFEBUY BGA GQE 80 490 TBD SNPB Level-2A-235C-4 WKS -40 to 85 AIC23BIG MICROSTAR JUNIOR TLV320AIC23BIPW ACTIVE TSSOP PW 28 50 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 85 AIC23BI & no Sb/Br) TLV320AIC23BIPWG4 ACTIVE TSSOP PW 28 50 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 85 AIC23BI & no Sb/Br) TLV320AIC23BIPWR ACTIVE TSSOP PW 28 2000 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 85 AIC23BI & no Sb/Br) TLV320AIC23BIPWRG4 ACTIVE TSSOP PW 28 2000 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 85 AIC23BI & no Sb/Br) TLV320AIC23BIRHD ACTIVE VQFN RHD 28 73 Green (RoHS CU NIPDAU Level-2-260C-1 YEAR -40 to 85 AIC23BI & no Sb/Br) TLV320AIC23BIRHDG4 ACTIVE VQFN RHD 28 73 Green (RoHS CU NIPDAU Level-2-260C-1 YEAR -40 to 85 AIC23BI & no Sb/Br) TLV320AIC23BIRHDR ACTIVE VQFN RHD 28 3000 Green (RoHS CU NIPDAU Level-2-260C-1 YEAR -40 to 85 AIC23BI & no Sb/Br) TLV320AIC23BIZQE LIFEBUY BGA ZQE 80 360 Green (RoHS SNAGCU Level-3-260C-168 HR -40 to 85 AIC23BIZ MICROSTAR & no Sb/Br) JUNIOR TLV320AIC23BPW ACTIVE TSSOP PW 28 50 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -10 to 70 AIC23B & no Sb/Br) TLV320AIC23BPWG4 ACTIVE TSSOP PW 28 50 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -10 to 70 AIC23B & no Sb/Br) TLV320AIC23BPWR ACTIVE TSSOP PW 28 2000 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -10 to 70 AIC23B & no Sb/Br) TLV320AIC23BRHD ACTIVE VQFN RHD 28 73 Green (RoHS CU NIPDAU Level-2-260C-1 YEAR -10 to 70 AIC23B & no Sb/Br) TLV320AIC23BRHDR ACTIVE VQFN RHD 28 3000 Green (RoHS CU NIPDAU Level-2-260C-1 YEAR -10 to 70 AIC23B & no Sb/Br) Addendum-Page 1

PACKAGE OPTION ADDENDUM www.ti.com 21-May-2019 Orderable Device Status Package Type Package Pins Package Eco Plan Lead/Ball Finish MSL Peak Temp Op Temp (°C) Device Marking Samples (1) Drawing Qty (2) (6) (3) (4/5) TLV320AIC23BZQE ACTIVE BGA ZQE 80 360 Green (RoHS SNAGCU Level-3-260C-168 HR -10 to 70 AIC23BZ MICROSTAR & no Sb/Br) JUNIOR TLV320AIC23BZQER ACTIVE BGA ZQE 80 2500 Green (RoHS SNAGCU Level-3-260C-168 HR -10 to 70 AIC23BZ MICROSTAR & no Sb/Br) JUNIOR (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based flame retardants must also meet the <=1000ppm threshold requirement. (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2

PACKAGE OPTION ADDENDUM www.ti.com 21-May-2019 OTHER QUALIFIED VERSIONS OF TLV320AIC23B : •Automotive: TLV320AIC23B-Q1 NOTE: Qualified Version Definitions: •Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects Addendum-Page 3

PACKAGE MATERIALS INFORMATION www.ti.com 26-Feb-2019 TAPE AND REEL INFORMATION *Alldimensionsarenominal Device Package Package Pins SPQ Reel Reel A0 B0 K0 P1 W Pin1 Type Drawing Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant (mm) W1(mm) TLV320AIC23BIPWR TSSOP PW 28 2000 330.0 16.4 6.9 10.2 1.8 12.0 16.0 Q1 TLV320AIC23BIRHDR VQFN RHD 28 3000 330.0 12.4 5.3 5.3 1.5 8.0 12.0 Q2 TLV320AIC23BPWR TSSOP PW 28 2000 330.0 16.4 6.9 10.2 1.8 12.0 16.0 Q1 TLV320AIC23BRHDR VQFN RHD 28 3000 330.0 12.4 5.3 5.3 1.5 8.0 12.0 Q2 TLV320AIC23BZQER BGAMI ZQE 80 2500 330.0 12.4 5.3 5.3 1.5 8.0 12.0 Q1 CROSTA RJUNI OR PackMaterials-Page1

PACKAGE MATERIALS INFORMATION www.ti.com 26-Feb-2019 *Alldimensionsarenominal Device PackageType PackageDrawing Pins SPQ Length(mm) Width(mm) Height(mm) TLV320AIC23BIPWR TSSOP PW 28 2000 350.0 350.0 43.0 TLV320AIC23BIRHDR VQFN RHD 28 3000 350.0 350.0 43.0 TLV320AIC23BPWR TSSOP PW 28 2000 350.0 350.0 43.0 TLV320AIC23BRHDR VQFN RHD 28 3000 350.0 350.0 43.0 TLV320AIC23BZQER BGAMICROSTAR ZQE 80 2500 350.0 350.0 43.0 JUNIOR PackMaterials-Page2

None

None

None

None

None

None

None

None

IMPORTANTNOTICEANDDISCLAIMER TIPROVIDESTECHNICALANDRELIABILITYDATA(INCLUDINGDATASHEETS),DESIGNRESOURCES(INCLUDINGREFERENCE DESIGNS),APPLICATIONOROTHERDESIGNADVICE,WEBTOOLS,SAFETYINFORMATION,ANDOTHERRESOURCES“ASIS” ANDWITHALLFAULTS,ANDDISCLAIMSALLWARRANTIES,EXPRESSANDIMPLIED,INCLUDINGWITHOUTLIMITATIONANY IMPLIEDWARRANTIESOFMERCHANTABILITY,FITNESSFORAPARTICULARPURPOSEORNON-INFRINGEMENTOFTHIRD PARTYINTELLECTUALPROPERTYRIGHTS. TheseresourcesareintendedforskilleddevelopersdesigningwithTIproducts.Youaresolelyresponsiblefor(1)selectingtheappropriate TIproductsforyourapplication,(2)designing,validatingandtestingyourapplication,and(3)ensuringyourapplicationmeetsapplicable standards,andanyothersafety,security,orotherrequirements.Theseresourcesaresubjecttochangewithoutnotice.TIgrantsyou permissiontousetheseresourcesonlyfordevelopmentofanapplicationthatusestheTIproductsdescribedintheresource.Other reproductionanddisplayoftheseresourcesisprohibited.NolicenseisgrantedtoanyotherTIintellectualpropertyrightortoanythird partyintellectualpropertyright.TIdisclaimsresponsibilityfor,andyouwillfullyindemnifyTIanditsrepresentativesagainst,anyclaims, damages,costs,losses,andliabilitiesarisingoutofyouruseoftheseresources. TI’sproductsareprovidedsubjecttoTI’sTermsofSale(www.ti.com/legal/termsofsale.html)orotherapplicabletermsavailableeitheron ti.comorprovidedinconjunctionwithsuchTIproducts.TI’sprovisionoftheseresourcesdoesnotexpandorotherwisealterTI’sapplicable warrantiesorwarrantydisclaimersforTIproducts. MailingAddress:TexasInstruments,PostOfficeBox655303,Dallas,Texas75265 Copyright©2019,TexasInstrumentsIncorporated