Product Sample & Technical Tools & Support & Reference Folder Buy Documents Software Community Design TLV3201,TLV3202 SBOS561B–MARCH2012–REVISEDDECEMBER2016 TLV320x 40-ns, microPOWER, Push-Pull Output Comparators 1 Features 3 Description • LowPropagationDelay:40ns The TLV3201 and TLV3202 are single- and dual- 1 channel comparators that offer the ultimate • LowQuiescentCurrent: combination of high speed (40 ns) and low-power 40µAperChannel consumption (40 µA), all in extremely small packages • InputCommon-ModeRangeExtends200mV with features such as rail-to-rail inputs, low offset BeyondEitherRail voltage (1 mV), and large output drive current. The devices are also very easy to implement in a wide • LowInputOffsetVoltage:1mV varietyofapplicationswhereresponsetimeiscritical. • Push-PullOutputs The TLV320x family is available in single (TLV3201) • SupplyRange:2.7Vto5.5V and dual (TLV3202) channel versions, both with • IndustrialTemperatureRange: push-pull outputs. The TLV3201 is available in 5-pin –40°Cto125°C SOT-23 and 5-pin SC70 packages. The TLV3202 is • SmallPackages: available in 8-pin SOIC and 8-pin VSSOP packages. 5-PinSC70,5-PinSOT-23,8-PinSOIC,8-Pin All devices are specified for operation across the VSSOP expanded industrial temperature range of –40°C to 125°C. 2 Applications DeviceInformation(1) • InspectionEquipment PARTNUMBER PACKAGE BODYSIZE(NOM) • TestandMeasurement SOT-23(5) 2.90mm×1.60mm TLV3201 • High-SpeedSamplingSystems SC70(5) 2.00mm×1.25mm • Telecom VSSOP(8) 3.00mm×3.00mm TLV3202 • PortableCommunications SOIC(8) 4.90mm×3.91mm (1) For all available packages, see the orderable addendum at theendofthedatasheet. ThresholdDetector V V IN CC C1 C2 R1 V R2 OUT V REF Copyright © 2016,Texas Instruments Incorporated 1 An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications, intellectualpropertymattersandotherimportantdisclaimers.UNLESSOTHERWISENOTED,thisdocumentcontainsPRODUCTION DATA.

TLV3201,TLV3202 SBOS561B–MARCH2012–REVISEDDECEMBER2016 www.ti.com Table of Contents 1 Features.................................................................. 1 8.4 DeviceFunctionalModes........................................11 2 Applications........................................................... 1 9 ApplicationandImplementation........................ 12 3 Description............................................................. 1 9.1 ApplicationInformation............................................12 4 RevisionHistory..................................................... 2 9.2 TypicalApplications................................................16 5 DeviceComparisonTable..................................... 3 10 PowerSupplyRecommendations..................... 18 6 PinConfigurationandFunctions......................... 3 11 Layout................................................................... 19 11.1 LayoutGuidelines.................................................19 7 Specifications......................................................... 4 11.2 LayoutExample....................................................19 7.1 AbsoluteMaximumRatings......................................4 12 DeviceandDocumentationSupport................. 20 7.2 ESDRatings..............................................................4 7.3 RecommendedOperatingConditions.......................4 12.1 DeviceSupport ....................................................20 7.4 ThermalInformation..................................................4 12.2 DocumentationSupport .......................................20 7.5 ElectricalCharacteristics:V =5V.........................5 12.3 RelatedLinks........................................................21 CC 7.6 ElectricalCharacteristics:V =2.7V......................5 12.4 ReceivingNotificationofDocumentationUpdates21 CC 7.7 SwitchingCharacteristics..........................................6 12.5 CommunityResource............................................21 7.8 TypicalCharacteristics..............................................7 12.6 Trademarks...........................................................21 12.7 ElectrostaticDischargeCaution............................21 8 DetailedDescription............................................ 11 12.8 Glossary................................................................21 8.1 Overview.................................................................11 13 Mechanical,Packaging,andOrderable 8.2 FunctionalBlockDiagram.......................................11 Information........................................................... 21 8.3 FeatureDescription.................................................11 4 Revision History NOTE:Pagenumbersforpreviousrevisionsmaydifferfrompagenumbersinthecurrentversion. ChangesfromRevisionA(June2012)toRevisionB Page • AddedESDRatingstable,FeatureDescriptionsection,DeviceFunctionalModes,ApplicationandImplementation section,PowerSupplyRecommendationssection,Layoutsection,DeviceandDocumentationSupportsection,and Mechanical,Packaging,andOrderableInformationsection ................................................................................................. 1 • DeletedOrderingInformationtable;seePackageOptionAddendumattheendofthedatasheet...................................... 1 ChangesfromOriginal(March2012)toRevisionA Page • ChangedproductstatusfromProductionDatatoMixedStatus............................................................................................ 1 • Addeddualchanneldevice.................................................................................................................................................... 1 2 SubmitDocumentationFeedback Copyright©2012–2016,TexasInstrumentsIncorporated ProductFolderLinks:TLV3201 TLV3202

TLV3201,TLV3202 www.ti.com SBOS561B–MARCH2012–REVISEDDECEMBER2016 5 Device Comparison Table DEVICE DESCRIPTION 5-µA(maximum)open-drain,1.8-Vto5.5-Vwithintegratedvoltagereferencein1.5-mm×1.5-mmmicro-sized TLV3011 packages TLV3012 5-µA(maximum)push-pull,1.8-Vto5.5-Vwithintegratedvoltagereferenceinmicro-sizedpackages TLV3501 4.5-ns,rail-to-rail,push-pullcomparatorinmicro-sizedpackages LMV7235 75-ns,65-µA,2.7-Vto5.5-V,rail-to-railinputcomparatorwithopen-drainoutput REF3333 30-ppm/°Cdrift,3.9-µA,SOT23-3,SC70-3voltagereference 6 Pin Configuration and Functions TLV3201DCKandDBVPackages 5-PinSC70-5andSOT-23 TopView OUT 1 5 V CC GND 2 IN+ 3 4 IN- PinFunctions:TLV3201 PIN I/O DESCRIPTION NAME NO. GND 2 — Negativesupply,ground IN– 4 I Negativeinput IN+ 3 I Positiveinput OUT 1 O Output V 5 — Positivesupply CC TLV3202DandDGKPackages 8-PinSOICandVSSOP TopView 1OUT 1 8 VCC 1IN- 2 7 2OUT 1IN+ 3 6 2IN- GND 4 5 2IN+ PinFunctions:TLV3202 PIN I/O DESCRIPTION NAME NO. 1IN– 2 I Negativeinput,comparator1 1IN+ 3 I Positiveinput,comparator1 1OUT 1 O Output,comparator1 2IN– 6 I Negativeinput,comparator2 2IN+ 5 I Positiveinput,comparator2 2OUT 7 O Output,comparator2 GND 4 — Negativesupply,ground V 8 — Positivesupply CC Copyright©2012–2016,TexasInstrumentsIncorporated SubmitDocumentationFeedback 3 ProductFolderLinks:TLV3201 TLV3202

TLV3201,TLV3202 SBOS561B–MARCH2012–REVISEDDECEMBER2016 www.ti.com 7 Specifications 7.1 Absolute Maximum Ratings overoperatingfree-airtemperaturerange(unlessotherwisenoted)(1) MIN MAX UNIT Supplyvoltage 7 Voltage V Signalinputpins(2) –0.5 (V )+0.5 CC Signalinputpins(2) –10 10 Current mA Outputshortcircuit(3) 100 Operating –55 125 Temperature Junction,T 150 °C J Storage,T –65 150 stg (1) StressesbeyondthoselistedunderAbsoluteMaximumRatingsmaycausepermanentdamagetothedevice.Thesearestressratings only,whichdonotimplyfunctionaloperationofthedeviceattheseoranyotherconditionsbeyondthoseindicatedunderRecommended OperatingConditions.Exposuretoabsolute-maximum-ratedconditionsforextendedperiodsmayaffectdevicereliability. (2) Inputpinsarediode-clampedtothepower-supplyrails.Inputsignalsthatcanswingmorethan0.5Vbeyondthesupplyrailsmustbe currentlimitedto10mAorless. (3) Short-circuittoground. 7.2 ESD Ratings VALUE UNIT Human-bodymodel(HBM),perANSI/ESDA/JEDECJS-001(1) ±2000 V(ESD) Electrostaticdischarge Charged-devicemodel(CDM), TLV3201 ±2000 V perJEDECspecificationJESD22-C101(2) TLV3202 ±1000 (1) JEDECdocumentJEP155statesthat500-VHBMallowssafemanufacturingwithastandardESDcontrolprocess. (2) JEDECdocumentJEP157statesthat250-VCDMallowssafemanufacturingwithastandardESDcontrolprocess. 7.3 Recommended Operating Conditions overoperatingfree-airtemperaturerange(unlessotherwisenoted) MIN MAX UNIT V Supplyvoltage,V =(V )–(V ) 2.7(±1.35) 5.5(±2.75) V S S S+ S– Specifiedtemperature –40 125 °C 7.4 Thermal Information TLV3201 TLV3202 THERMALMETRIC(1) DBV DCK DGK D UNIT (SOT-23) (SC70) (VSSOP) (SOIC) 5PINS 5PINS 8PINS 8PINS R Junction-to-ambientthermalresistance 237.8 281.9 146.3 201.9 °C/W θJA R Junction-to-case(top)thermalresistance 108.7 97.6 97.2 92.5 °C/W θJC(top) R Junction-to-boardthermalresistance 64.1 68.3 84.2 123.3 °C/W θJB ψ Junction-to-topcharacterizationparameter 12.1 2.6 45.5 23 °C/W JT ψ Junction-to-boardcharacterizationparameter 63.3 67.3 83.7 212.6 °C/W JB (1) Formoreinformationabouttraditionalandnewthermalmetrics,seetheSemiconductorandICPackageThermalMetricsapplication report. 4 SubmitDocumentationFeedback Copyright©2012–2016,TexasInstrumentsIncorporated ProductFolderLinks:TLV3201 TLV3202

TLV3201,TLV3202 www.ti.com SBOS561B–MARCH2012–REVISEDDECEMBER2016 7.5 Electrical Characteristics: V = 5 V CC atT =25°CandV =5V(unlessotherwisenoted) A CC PARAMETER TESTCONDITIONS MIN TYP MAX UNIT OFFSETVOLTAGE VCM=VCC/2 1 5 VIO Inputoffsetvoltage mV TA=–40°Cto125°C 6 dVOS/dT Inputoffsetvoltagedrift TA=–40°Cto125°C 1 10 µV/°C PSRR Power-supplyrejectionratio VCM=VCC/2,VCC=2.5Vto5.5V 65 85 dB Inputhysteresis 1.2 mV INPUTBIASCURRENT VCM=VCC/2 1 50 pA IIB Inputbiascurrent TA=–40°Cto125°C 5 nA VCM=VCC/2 1 50 pA IIO Inputoffsetcurrent TA=–40°Cto125°C 2.5 nA INPUTVOLTAGERANGE VCM Common-modevoltage TA=–40°Cto125°C (VEE)–0.2 (VCC)+0.2 V CMRR Common-moderejectionratio –0.2V<VCM<5.2V 60 70 dB INPUTIMPEDANCE Commonmode 1013||2 Ω||pF Differential 1013||4 Ω||pF OUTPUT ISINK=4mA 175 190 VOL Voltageoutputswingfromlowerrail mV TA=–40°Cto125°C 225 ISOURCE=4mA 120 140 VOH Voltageoutputswingfromupperrail mV TA=–40°Cto125°C 170 ISCsinking 40 48 TA=–40°Cto125°C SeeFigure14 ISC Short-circuitcurrent(percomparator) mA ISCsourcing 52 60 TA=–40°Cto125°C SeeFigure14 POWERSUPPLY VCC Specifiedvoltage 2.7 5.5 V TA=25°C 40 50 IQ Quiescentcurrent µA TA=–40°Cto125°C 65 7.6 Electrical Characteristics: V = 2.7 V CC atT =25°CandV =2.7V(unlessotherwisenoted) A CC PARAMETER TESTCONDITIONS MIN TYP MAX UNIT OFFSETVOLTAGE VCM=VCC/2 1 5 VIO Inputoffsetvoltage mV TA=–40°Cto125°C 6 dVOS/dT Inputoffsetvoltagedrift TA=–40°Cto125°C 1 10 µV/°C PSRR Power-supplyrejectionratio VCM=VCC/2,VCC=2.5Vto5.5V 65 85 dB Inputhysteresis 1.2 mV INPUTBIASCURRENT VCM=VCC/2 1 50 pA IIB Inputbiascurrent TA=–40°Cto125°C 5 nA VCM=VCC/2 1 50 pA IIO Inputoffsetcurrent TA=–40°Cto125°C 2.5 nA INPUTVOLTAGERANGE VCM Common-modevoltage TA=–40°Cto125°C (VEE)–0.2 (VCC)+0.2 V CMRR Common-moderejectionratio –0.2V<VCM<2.9V 56 68 dB Copyright©2012–2016,TexasInstrumentsIncorporated SubmitDocumentationFeedback 5 ProductFolderLinks:TLV3201 TLV3202

TLV3201,TLV3202 SBOS561B–MARCH2012–REVISEDDECEMBER2016 www.ti.com Electrical Characteristics: V = 2.7 V (continued) CC atT =25°CandV =2.7V(unlessotherwisenoted) A CC PARAMETER TESTCONDITIONS MIN TYP MAX UNIT INPUTIMPEDANCE Commonmode 1013||2 Ω||pF Differential 1013||4 Ω||pF OUTPUT ISINK=4mA 230 260 VOL Voltageoutputswingfromlowerrail mV TA=–40°Cto125°C 325 ISOURCE=4mA 210 250 VOH Voltageoutputswingfromupperrail mV TA=–40°Cto125°C 350 ISCsinking 13 19 TA=–40°Cto125°C SeeFigure14 ISC Short-circuitcurrent(percomparator) mA ISCsourcing 15 21 TA=–40°Cto125°C SeeFigure14 POWERSUPPLY VCC Specifiedvoltage 2.7 5.5 V TA=25°C 36 46 IQ Quiescentcurrent µA TA=–40°Cto125°C 60 7.7 Switching Characteristics overoperatingfree-airtemperaturerange(unlessotherwisenoted) PARAMETER TESTCONDITIONS MIN TYP MAX UNIT Inputoverdrive=20mV,CL=15pF 47 50 Lowtohigh Inputoverdrive=100mV,CL=15pF 42 50 TA=–40°Cto125°C 55 tPD Propagationdelaytime ns Inputoverdrive=20mV,CL=15pF 40 50 Hightolow Inputoverdrive=100mV,CL=15pF 38 50 TA=–40°Cto125°C 55 Propagationdelayskew Inputoverdrive=20mV,CL=15pF 2 ns Propagationdelaymatching(TLV3202) Hightoloworlowtohigh,inputoverdrive=20mV,CL=15pF 5 ns tR Risetime 10%to90% 4.8 ns tF Falltime 10%to90% 5.2 ns 6 SubmitDocumentationFeedback Copyright©2012–2016,TexasInstrumentsIncorporated ProductFolderLinks:TLV3201 TLV3202

TLV3201,TLV3202 www.ti.com SBOS561B–MARCH2012–REVISEDDECEMBER2016 7.8 Typical Characteristics atT =25°C,V =5V,andinputoverdrive(V )=20mV(unlessotherwisenoted) A CC OD 26 30 24 27 22 %) %) 24 ers ( 1280 ers ( 21 plifi 16 plifi 18 m 14 m A A 15 of 12 of ge 10 ge 12 a a nt 8 nt 9 e e c 6 c e e 6 P 4 P 2 3 0 0 555544553355225511550055115522553355445555 00 22 44 66 88 11 22 44 66 88 22 22 44 66 88 33 −−4.4.−−3.3.−−2.2.−−1.1.−−0.0. 0.0. 1.1. 2.2. 3.3. 4.4. 0.0. 0.0. 0.0. 0.0. 1.1. 1.1. 1.1. 1.1. 2.2. 2.2. 2.2. 2.2. −− −− −− −− −− Offset Voltage (mV) Hysteresis (mV) G000 G001 Figure1.OffsetVoltageDistribution Figure2.HysteresisDistribution 5 6 4 5 Typical Units Shown 5 VCC = 2.7 V 5 Typical Units Shown 3 4 V) 2 V) 3 m m e ( 1 e ( 2 g g olta 0 olta 1 V V et −1 et 0 s s Off −2 Off −1 −3 −2 −4 −3 −5 −4 −40 −25 −10 5 20 35 50 65 80 95 110 125 −0.5 0 0.5 1 1.5 2 2.5 3 Temperature (°C) Common−Mode Voltage (V) G002 G003 Figure3.OffsetVoltagevsTemperature Figure4.OffsetVoltagevsCommon-ModeVoltage 6 5 5 VCC = 5.5 V 5 Typical Units Shown 4 8 Typical Units Shown 4 3 V) 3 V) 2 m m e ( 2 e ( 1 g g olta 1 olta 0 V V et 0 et −1 s s Off −1 Off −2 −2 −3 −3 −4 −4 −5 −0.5 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 2.5 3 3.5 4 4.5 5 5.5 Common−Mode Voltage (V) Supply Voltage (V) G004 G005 Figure5.OffsetVoltagevsCommon-ModeVoltage Figure6.OffsetVoltagevsPowerSupply Copyright©2012–2016,TexasInstrumentsIncorporated SubmitDocumentationFeedback 7 ProductFolderLinks:TLV3201 TLV3202

TLV3201,TLV3202 SBOS561B–MARCH2012–REVISEDDECEMBER2016 www.ti.com Typical Characteristics (continued) atT =25°C,V =5V,andinputoverdrive(V )=20mV(unlessotherwisenoted) A CC OD 110 10000 - IB 100 +IB B) A) 1000 IOS d p RR ( 90 ent ( 100 nd PS 80 s Curr R a Bia 10 MR 70 put C n 60 CMRR at VCC = 2.7 V I 1 CMRR at VCC = 5.0 V PSRR 50 0.1 −40 −25 −10 5 20 35 50 65 80 95 110 125 −50 −25 0 25 50 75 100 125 Temperature (°C) Temperature (°C) G006 G002 Figure7.Common-ModeRejectionRatioand Figure8.InputBiasCurrentandInputOffsetCurrent Power-SupplyRejectionRatiovsTemperature vsTemperature 30 20 25 VS=2.7V +IB VS= 5.5V +IB 20 - IB 15 - IB A) 15 IOS A) 10 IOS p p nt ( 10 nt ( 5 urre 5 urre C 0 C 0 as −5 as Bi Bi −5 ut −10 ut np −15 np −10 I I −20 −15 −25 −30 −20 0.0 0.5 1.0 1.5 2.0 2.5 0 1 2 3 4 5 Common−Mode Input Voltage (V) Common−Mode Input Voltage (V) G006 G006 Figure9.InputBiasCurrentandInputOffsetCurrent Figure10.InputBiasCurrentandInputOffsetCurrent vsCommon-ModeInputVoltage vsCommon-ModeInputVoltage 35 65 −40°C 30 25°C %) 55 125°C Amplifiers ( 2205 Current (µA) 45 e of 15 ent 35 g c ecenta 10 Quies 25 P 5 0 15 2.5 3 3.5 4 4.5 5 5.5 44 55 66 77 88 99 00 11 22 33 44 55 66 77 88 99 00 33 33 33 33 33 33 44 44 44 44 44 44 44 44 44 44 55 Supply Voltage (V) G018 Supply Current (µA) G000 Figure11.QuiescentCurrentDistribution Figure12.QuiescentCurrentvsSupplyVoltage 8 SubmitDocumentationFeedback Copyright©2012–2016,TexasInstrumentsIncorporated ProductFolderLinks:TLV3201 TLV3202

TLV3201,TLV3202 www.ti.com SBOS561B–MARCH2012–REVISEDDECEMBER2016 Typical Characteristics (continued) atT =25°C,V =5V,andinputoverdrive(V )=20mV(unlessotherwisenoted) A CC OD 90 ISC, Source: VCC = 5 V 80 ISC, Sink: VCC = 5 V A) ISC, Sink: VCC = 2.7 V ent (m 6700 ISC, Source: VCC = 2.7 V urr uit C 50 c Cir 40 ort 30 h S 20 10 −40 −15 10 35 60 85 110 125 Temperature (°C) G014 Figure13.QuiescentCurrentvsSwitchingFrequency Figure14.Short-CircuitCurrentvsTemperature 2.8 5.9 2.4 Sourcing Current 4.9 Sourcing Current 2 3.7 1.6 V) 1.2 V) 2.5 e ( 0.8 e ( 1.3 ag 0.4 −40°C ag −40°C Output Volt −−−100...2840 271552°°5CC°C VCC = 2.7 V Output Volt −−210...311 271552°°5CC°C VCC = 5.5 V −1.6 −3.5 −2 −2.4 Sinking Current −4.7 Sinking Current −2.8 −5.9 0 5 10 15 20 0 10 20 30 40 50 60 Output Current (mA) Output Current (mA) G015 G017 Figure15.OutputVoltagevsOutputCurrent Figure16.OutputVoltagevsOutputCurrent 140 3 140 3 120 Output: VOD = 20 mV 2.6 120 2.6 100 Input: VOD = 20 mV 2.1 100 2.1 80 Output: VOD = 100 mV 1.7 80 1.7 V) 60 Input: VOD = 100 mV 1.3 V) V) 60 1.3 V) put Voltage (m −−422400000 −−000..0049..94 utput Voltage ( put Voltage (m −−422400000 −−000..0049..94 utput Voltage ( In −60 −1.3 O In −60 Output: VOD = 20 mV −1.3 O −80 −1.7 −80 Input: VOD = 20 mV −1.7 −100 −2.1 −100 Output: VOD = 100 mV −2.1 −120 −2.6 −120 Input: VOD = 100 mV −2.6 −140 −3 −140 −3 20 40 60 80 100 120 140 160 180 200 220 20 40 60 80 100 120 140 160 180 200 220 240 Time (ns) Time (ns) G000 G019 Figure17.PropagationDelayFallingEdge Figure18.PropagationDelayRisingEdge Copyright©2012–2016,TexasInstrumentsIncorporated SubmitDocumentationFeedback 9 ProductFolderLinks:TLV3201 TLV3202

TLV3201,TLV3202 SBOS561B–MARCH2012–REVISEDDECEMBER2016 www.ti.com Typical Characteristics (continued) atT =25°C,V =5V,andinputoverdrive(V )=20mV(unlessotherwisenoted) A CC OD 100 50 90 PDHL: 5 V 48 Falling Edge PDLH: 5 V Rising Edge y (ns) 7800 PPDDHLHL:: 22..77 VV y (ns) 4446 ela 60 ela 42 D D n 50 n 40 o o ati 40 ati 38 g g a a op 30 op 36 Pr Pr 20 34 10 32 0 30 20 30 40 50 60 70 80 90 100 −40 −25 −10 5 20 35 50 65 80 95 110 125 Input Overdrive (mV) Temperature (°C) G003 G017 Figure19.PropagationDelayvsInputOverdrive Figure20.PropagationDelayvsTemperature 60 60 58 VCC= 2.7V Falling Edge 58 VCC= 5.5V Falling Edge Rising Edge Rising Edge ns) 56 ns) 56 AY ( 54 AY ( 54 L L DE 52 DE 52 N N O 50 O 50 TI TI A 48 A 48 G G A 46 A 46 P P O O R 44 R 44 P P 42 42 40 40 −0.2 0.2 0.6 1 1.4 1.8 2.2 2.6 2.9 −0.2 0.4 1 1.6 2.2 2.8 3.4 4 4.6 5.2 5.7 Common−Mode Input Voltage (V) Common−Mode Input Voltage (V) G017 G017 Figure21.PropagationDelayvsCommon-ModeVoltage Figure22.PropagationDelayvsCommon-ModeVoltage 60 60 58 Falling Edge PDLH:Vod = 20 mV Rising Edge PDHL:Vod = 20 mV y (ns) 5546 y (ns) 55 PPDDLHHL::VVoodd == 5500 mmVV ela 52 ela D D n 50 n o o ati 48 ati 45 g g a a op 46 op Pr Pr 44 42 VCC= 5.5 V 40 35 2.5 3 3.5 4 4.5 5 5.5 0 25 50 75 100 Supply Voltage (V) Capacitive Load (pF) G005 G024 Figure23.PropagationDelayvsSupplyVoltage Figure24.PropagationDelayvsCapacitiveLoad 10 SubmitDocumentationFeedback Copyright©2012–2016,TexasInstrumentsIncorporated ProductFolderLinks:TLV3201 TLV3202

TLV3201,TLV3202 www.ti.com SBOS561B–MARCH2012–REVISEDDECEMBER2016 8 Detailed Description 8.1 Overview The TLV3201 and TLV3202 devices feature 40-ns response time, and include 1.2 mV of internal hysteresis for improvednoiseimmunitywithaninputcommon-moderangethatextends0.2Vbeyondthepower-supplyrails. 8.2 Functional Block Diagram V+ +IN + OUT -IN - V- Copyright © 2016,Texas Instruments Incorporated 8.3 Feature Description 8.3.1 OperatingVoltage The TLV3201 and TLV3202 comparators are specified for use on a single supply from 2.7 V to 5.5 V (or a dual supply from ±1.35 V to ±2.75 V) over a temperature range of −40°C to 125°C. The device continues to function belowthisrange,butperformanceisnotspecified. 8.3.2 InputOvervoltageProtection Thedeviceinputsareprotectedbyelectrostaticdischarge(ESD)diodesthatconductiftheinputvoltagesexceed the power supplies by more than approximately 300 mV. Momentary voltages greater than 300 mV beyond the power supply can be tolerated if the input current is limited to 10 mA. This limiting is easily accomplished with a smallinputresistorinserieswiththeinputtothecomparator. 8.4 Device Functional Modes The device is fully functional when powered by rail-to-rail supply voltage greater than 2.7 V. The device is off at anyvoltagesbelow2.7V. Copyright©2012–2016,TexasInstrumentsIncorporated SubmitDocumentationFeedback 11 ProductFolderLinks:TLV3201 TLV3202

TLV3201,TLV3202 SBOS561B–MARCH2012–REVISEDDECEMBER2016 www.ti.com 9 Application and Implementation NOTE Information in the following applications sections is not part of the TI component specification, and TI does not warrant its accuracy or completeness. TI’s customers are responsible for determining suitability of components for their purposes. Customers should validateandtesttheirdesignimplementationtoconfirmsystemfunctionality. 9.1 Application Information The TLV3201 and TLV3202 are single- and dual-supply (respectively), push-pull comparators featuring 40 ns of propagation delay on only 40 µA of supply current. This combination of fast response time and minimal power consumption make the TLV3201 and TLV3202 excellent comparators for portable, battery-powered applications as well as fast-switching threshold detection such as pulse-width modulation (PWM) output monitors and zero- crossdetection. 9.1.1 ComparatorInputs The TLV3201 and TLV3202 are rail-to-rail input comparators, with an input common-mode range that exceeds thesupplyrailsby200mVforbothpositiveandnegativesupplies.Thedevicesarespecifiedfrom2.7Vto5.5V, with room temperature operation from 2.5 V to 5.5 V. The TLV3201 and TLV3202 are designed to prevent phase inversion when the input pins exceed the supply voltage. Figure 25 shows the TLV320x response when input voltagesexceedthesupply,resultinginnophaseinversion. 5 Output Voltage 4 Input Voltage 3 2 V) 1 e ( g 0 a olt −1 V −2 −3 −4 −5 0 20 40 60 80 100 120 140 160 180 200 Time (ns) G000 Figure25. NoPhaseInversion:ComparatorResponsetoInputVoltage(PropagationDelayIncluded) The electrostatic discharge (ESD) protection input structure of two back-to-back diodes and 1-kΩ series resistors are used to limit the differential input voltage applied to the precision input of the comparator by clamping input voltages that exceed V beyond the specified operating conditions. If potential overvoltage conditions that CC exceed absolute maximum ratings are present, the addition of external bypass diodes and resistors is recommended, as shown in Figure 26. Large differential voltages greater than the supply voltage must be avoidedtopreventdamagetotheinputstage. 1 kW Clamp +In Core -In 1 kW Copyright © 2016,Texas Instruments Incorporated Figure26. TLV3201EquivalentInputstructure 12 SubmitDocumentationFeedback Copyright©2012–2016,TexasInstrumentsIncorporated ProductFolderLinks:TLV3201 TLV3202

TLV3201,TLV3202 www.ti.com SBOS561B–MARCH2012–REVISEDDECEMBER2016 Application Information (continued) 9.1.2 ExternalHysteresis The TLV3201 and TLV3202 have a hysteresis transfer curve (shown in Figure 27) that is a function of three components:V ,V ,andV . TH OS HYST • V :theactualsetvoltageorthresholdtripvoltage TH • V : the internal offset voltage between V and V . This voltage is added to V to form the actual trip OS IN+ IN– TH pointatwhichthecomparatormustrespondtochangeoutputstates. • V :internalhysteresis(ortripwindow)thatisdesignedtoreducecomparatorsensitivitytonoise. HYST V + V -V V + V V + V + V TH OS HYST TH OS TH OS HYST Figure27. TLV320xHysteresisTransferCurve 9.1.2.1 InvertingComparatorwithHysteresis The inverting comparator with hysteresis requires a three-resistor network that is referenced to the comparator supply voltage (V ), as shown in Figure 28. When V at the inverting input is less than V , the output voltage is CC IN A high (for simplicity, assume V switches as high as V ). The three network resistors can be represented as R1 O CC ||R3inserieswithR2.Thelowerinputtripvoltage(V )isdefinedbyEquation1. A1 ´ R2 V = V A1 CC (R1 || R3) + R2 (1) When V is greater than [V × (V > V )], the output voltage is low, very close to ground. In this case, the three IN A IN A network resistors can be presented as R2 || R3 in series with R1. The upper trip voltage (V ) is defined by A2 Equation2. R2|| R3 ´ V = V A2 CC R1 + (R2 || R3) (2) ThetotalhysteresisprovidedbythenetworkisdefinedbyEquation3. DV = V -V A A1 A2 (3) Copyright©2012–2016,TexasInstrumentsIncorporated SubmitDocumentationFeedback 13 ProductFolderLinks:TLV3201 TLV3202

TLV3201,TLV3202 SBOS561B–MARCH2012–REVISEDDECEMBER2016 www.ti.com Application Information (continued) +V CC +5 V R1 1 MW V IN 5 V VA R10L0O AkDW VO V V A2 A1 0 V R3 1.67 V V 3.33 V R2 1 MW IN 1 MW V High V Low O O +VCC +VCC R1 R3 R1 V V A1 A2 R2 R2 R3 Copyright © 2016,Texas Instruments Incorporated Figure28. TLV3201inInvertingConfigurationWithHysteresis 9.1.2.2 NoninvertingComparatorWithHysteresis A noninverting comparator with hysteresis requires a two-resistor network, as shown in Figure 29, and a voltage reference (V ) at the inverting input. When V is low, the output is also low. For the output to switch from low REF IN tohigh,V mustriseuptoV .V iscalculatedbyEquation4. IN IN1 IN1 V V = R1´ REF ´V IN1 R2 REF (4) When V is high, the output is also high. In order for the comparator to switch back to a low state, V must IN IN equalV beforeV isagainequaltoV .V canbecalculatedbyEquation5. REF A REF IN V (R1 + R2)-V ´R1 V = REF CC IN2 R2 (5) ThehysteresisofthiscircuitisthedifferencebetweenV andV ,asdefinedbyEquation6. IN1 IN2 R1 DV = V ´ IN CC R2 (6) 14 SubmitDocumentationFeedback Copyright©2012–2016,TexasInstrumentsIncorporated ProductFolderLinks:TLV3201 TLV3202

TLV3201,TLV3202 www.ti.com SBOS561B–MARCH2012–REVISEDDECEMBER2016 Application Information (continued) +V CC +5 V V REF +2.5 V VO V A VIN RLOAD R1 330 kW R2 1 MW V High V Low O O +V V CC IN1 5 V R2 R1 VA= VREF VA= VREF VO V V IN2 IN1 R1 R2 0 V 1.675 V 3.325 V V IN V IN2 Copyright © 2016,Texas Instruments Incorporated Figure29. TLV3201inNoninvertingConfigurationWithHysteresis 9.1.3 CapacitiveLoads The TLV3201 and TLV3202 feature a push-pull output. When the output switches, there is a direct path between V and ground, causing increased output sinking or sourcing current during the transition. Following the CC transition the output current decreases and supply current returns to 40 µA, thus maintaining low power consumption. Under reasonable capacitive loads, the TLV3201 and TLV3202 maintain specified propagation delay (see Typical Characteristics), but excessive capacitive loading under high switching frequencies may increasesupplycurrent,propagationdelay,orinducedecreasedslewrate. Copyright©2012–2016,TexasInstrumentsIncorporated SubmitDocumentationFeedback 15 ProductFolderLinks:TLV3201 TLV3202

TLV3201,TLV3202 SBOS561B–MARCH2012–REVISEDDECEMBER2016 www.ti.com 9.2 Typical Applications 9.2.1 TLV3201ConfiguredasanAC-CoupledComparator One of the benefits of AC coupling a single-supply comparator circuit is that it can block dc offsets induced by ground-loop offsets that could potentially produce either a false trip or a common-mode input violation. Figure 30 showstheTLV3201configuredasanac-coupledcomparator. R9 866W R3 Cable C1 1mF 1 kW V IN+ R1 R10 1 kW 50W VOUT VM1 3.3 V U2 R2 TLV3201 VIN C2 1mF 1 kW 3.3 V + R4 1 kW V2 V 3.3 V IN- V 100 m CM + Ground mismatch in signal source vs conditioning circuit Copyright © 2016,Texas Instruments Incorporated Figure30. TLV3201ConfiguredasanAC-CoupledComparator(Schematic) 9.2.1.1 DesignRequirements Designrequirementsinclude: • Abilitytotolerateupto ±100mVofcommon-modesignal. • TriggeronlyonACsignals(suchaszero-crossdetection). 9.2.1.2 DetailedDesignProcedure Designanalysis: • AC-coupled,high-passfrequency • Largecapacitorsrequirelongerstart-uptimefromdevicepoweron • Use1-µFcapacitortoachievehigh-passfrequencyofapproximately159Hz • Forhigh-passequivalent,useC =0.5µF,R =2kΩ IN IN 1. Setupinputdividersinitiallyforone-halfsupply(tobeincenterofacceptablecommon-moderange). 2. Adjusteitherdividerslightlyupwardsordownwardsasdesiredtoestablishquiescentoutputcondition. 3. Selectcouplingcapacitorsbasedonlowestexpectedfrequency. 16 SubmitDocumentationFeedback Copyright©2012–2016,TexasInstrumentsIncorporated ProductFolderLinks:TLV3201 TLV3202

TLV3201,TLV3202 www.ti.com SBOS561B–MARCH2012–REVISEDDECEMBER2016 Typical Applications (continued) 9.2.1.3 ApplicationCurve 4 VIN VCM 3 VOUT V) 2 e ( g a Volt 1 0 -1 0 100m 200m Time (s) Figure31. AC-CoupledComparatorResults 9.2.2 TLV3201andOPA320ConfiguredasaFast-ResponseOutputCurrentMonitor Figure 32 shows a single-supply current monitor configured as a difference amplifier with a gain of 50. The OPA320 waschosenforthiscircuitbecauseofitsgainbandwidth(20MHz),whichallowshigherspeedtriggering andmonitoringofthecurrentacrosstheshuntresistorfollowedbythefastresponseoftheTLV3201. + R5 V3 5 50 kW + C3 V2 5 100 pF VF1 R4 R7 U2 1 kW 1 kW OPA320 VF2 V OUT U4 TLV3201 R C1 R6 1S0H0UNWT 500 pF 1 kW + C2 VT2.6 V1 5 100 pF R2 R1 1 kW 50 kW IG1 Copyright © 2016,Texas Instruments Incorporated Figure32. TLV3201andOPA320ConfiguredasaFast-ResponseOutputCurrentMonitor Copyright©2012–2016,TexasInstrumentsIncorporated SubmitDocumentationFeedback 17 ProductFolderLinks:TLV3201 TLV3202

TLV3201,TLV3202 SBOS561B–MARCH2012–REVISEDDECEMBER2016 www.ti.com Typical Applications (continued) 9.2.3 TLV3201andTMP20ConfiguredasaPrecisionAnalogTemperatureSwitch Figure 33 shows the TMP20 and TLV3201 designed as a high-speed temperature switch. The TMP20 is an analog output temperature sensor where output voltage decreases with temperature. The comparator output is trippedwhentheoutputreachesacriticaltripthreshold. C2 100 nF VCC U2 V 4 TMP20 IN V+ 1 V T(V) VOUT 3 VOUT TEMP GND GND U1 2 5 TLV3201 + V 1.85 T VCC VCC + V3 5 Copyright © 2016,Texas Instruments Incorporated Figure33. TLV3201andTMP20ConfiguredasaPrecisionAnalogTemperatureSwitch 10 Power Supply Recommendations The TLV3201 and TLV3202 comparators are specified for use on a single supply from 2.7 V to 5.5 V (or a dual supply from ±1.35 V to ±2.75 V) over a temperature range of −40°C to 125°C. The device continues to function below this range, but performance is not specified. Place bypass capacitors close to the power-supply pins to reduce noise coupling in from noisy or high-impedance power supplies. For more detailed information on bypass capacitorplacement,seeLayoutGuidelines. 18 SubmitDocumentationFeedback Copyright©2012–2016,TexasInstrumentsIncorporated ProductFolderLinks:TLV3201 TLV3202

TLV3201,TLV3202 www.ti.com SBOS561B–MARCH2012–REVISEDDECEMBER2016 11 Layout 11.1 Layout Guidelines The TLV3201 and TLV3202 are fast-switching, high-speed comparators and require high-speed layout considerations.Forbestresults,maintainthefollowinglayoutguidelines. • Useaprinted-circuitboard(PCB)withagood,unbrokenlow-inductancegroundplane. • Placeadecouplingcapacitor(0.1-µFceramic,surface-mountcapacitor)ascloseaspossibletoV . CC • On the inputs and the output, keep lead lengths as short as possible to avoid unwanted parasitic feedback aroundthecomparator.Keepinputsawayfromtheoutput. • SolderthedevicedirectlytothePCBratherthanusingasocket. • For slow-moving input signals, take care to prevent parasitic feedback. A small capacitor (1000 pF or less) placed between the inputs can help eliminate oscillations in the transition region. This capacitor causes some degradation to propagation delay when the impedance is low. The topside ground plane runs between the outputandinputs. • The ground pin ground trace runs under the device up to the bypass capacitor, shielding the inputs from the outputs. 11.2 Layout Example Figure34. TLV320xBoardLayoutExample Copyright©2012–2016,TexasInstrumentsIncorporated SubmitDocumentationFeedback 19 ProductFolderLinks:TLV3201 TLV3202

TLV3201,TLV3202 SBOS561B–MARCH2012–REVISEDDECEMBER2016 www.ti.com 12 Device and Documentation Support 12.1 Device Support 12.1.1 DevelopmentSupport 12.1.1.1 TINA-TI™(FreeSoftwareDownload) TINA-TI™ is a simple, powerful, and easy-to-use circuit simulation program based on a SPICE engine. TINA-TI is a free, fully-functional version of the TINA software, preloaded with a library of macro models in addition to a range of both passive and active models. TINA-TI provides all the conventional dc, transient, and frequency domainanalysisofSPICE,aswellasadditionaldesigncapabilities. Available as a free download from the Analog eLab Design Center, TINA-TI offers extensive post-processing capability that allows users to format results in a variety of ways. Virtual instruments offer the ability to select inputwaveformsandprobecircuitnodes,voltages,andwaveforms,creatingadynamicquick-starttool. NOTE These files require that either the TINA software (from DesignSoft™) or TINA-TI software beinstalled.DownloadthefreeTINA-TIsoftwarefromtheTINA-TIfolder. 12.1.1.2 UniversalOpAmpEVM The Universal Op Amp EVM is a series of general-purpose, blank circuit boards that simplify prototyping circuits for a variety of IC package types. The evaluation module board design allows many different circuits to be constructed easily and quickly. Five models are offered, with each model intended for a specific package type. PDIP,SOIC,MSOP,TSSOPandSOT23packagesareallsupported. NOTE These boards are unpopulated, so users must provide their own ICs. TI recommends requestingseveralopampdevicesampleswhenorderingtheUniversalOpAmpEVM. 12.1.1.3 TIPrecisionDesigns TI Precision Designs are analog solutions created by TI’s precision analog applications experts and offer the theory of operation, component selection, simulation, complete PCB schematic and layout, bill of materials, and measured performance of many useful circuits. TI Precision Designs are available online at http://www.ti.com/ww/en/analog/precision-designs/. 12.1.1.4 WEBENCH®FilterDesigner WEBENCH® Filter Designer is a simple, powerful, and easy-to-use active filter design program. The WEBENCH Filter Designer lets you create optimized filter designs using a selection of TI operational amplifiers and passive componentsfromTI'svendorpartners. Available as a web-based tool from the WEBENCH® Design Center, WEBENCH® Filter Designer allows you to design,optimize,andsimulatecompletemultistageactivefiltersolutionswithinminutes. 12.2 Documentation Support 12.2.1 RelatedDocumentation The following documents are relevant to using the TLV320x, and recommended for reference. All are available fordownloadatwww.ti.com unlessotherwisenoted. • FrequencyDitheringWiththeUCC28950andTLV3201(SLUA646) • FrequencyDitheringwiththeUCC28180andTLV3201 (SLUA704) • ComparatorwithHysteresisReferenceDesign(TIDU020) 20 SubmitDocumentationFeedback Copyright©2012–2016,TexasInstrumentsIncorporated ProductFolderLinks:TLV3201 TLV3202

TLV3201,TLV3202 www.ti.com SBOS561B–MARCH2012–REVISEDDECEMBER2016 12.3 Related Links Table 1 lists quick access links. Categories include technical documents, support and community resources, toolsandsoftware,andquickaccesstosampleorbuy. Table1.RelatedLinks TECHNICAL TOOLS& SUPPORT& PARTS PRODUCTFOLDER SAMPLE&BUY DOCUMENTS SOFTWARE COMMUNITY TLV3201 Clickhere Clickhere Clickhere Clickhere Clickhere TLV3202 Clickhere Clickhere Clickhere Clickhere Clickhere 12.4 Receiving Notification of Documentation Updates To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper right corner, click on Alert me to register and receive a weekly digest of any product information that has changed.Forchangedetails,reviewtherevisionhistoryincludedinanyreviseddocument. 12.5 Community Resource The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of Use. TIE2E™OnlineCommunity TI'sEngineer-to-Engineer(E2E)Community.Createdtofostercollaboration amongengineers.Ate2e.ti.com,youcanaskquestions,shareknowledge,exploreideasandhelp solveproblemswithfellowengineers. DesignSupport TI'sDesignSupport QuicklyfindhelpfulE2Eforumsalongwithdesignsupporttoolsand contactinformationfortechnicalsupport. 12.6 Trademarks E2EisatrademarkofTexasInstruments. WEBENCHisaregisteredtrademarkofTexasInstruments. DesignSoftisatrademarkofDesignSoft,Inc. TINA-TIisatrademarkofTexasInsturmentsandDesignSoft,Inc.. Allothertrademarksarethepropertyoftheirrespectiveowners. 12.7 Electrostatic Discharge Caution Thesedeviceshavelimitedbuilt-inESDprotection.Theleadsshouldbeshortedtogetherorthedeviceplacedinconductivefoam duringstorageorhandlingtopreventelectrostaticdamagetotheMOSgates. 12.8 Glossary SLYZ022—TIGlossary. Thisglossarylistsandexplainsterms,acronyms,anddefinitions. 13 Mechanical, Packaging, and Orderable Information The following pages include mechanical, packaging, and orderable information. This information is the most current data available for the designated devices. This data is subject to change without notice and revision of thisdocument.Forbrowser-basedversionsofthisdatasheet,refertotheleft-handnavigation. Copyright©2012–2016,TexasInstrumentsIncorporated SubmitDocumentationFeedback 21 ProductFolderLinks:TLV3201 TLV3202

PACKAGE OPTION ADDENDUM www.ti.com 6-Feb-2020 PACKAGING INFORMATION Orderable Device Status Package Type Package Pins Package Eco Plan Lead/Ball Finish MSL Peak Temp Op Temp (°C) Device Marking Samples (1) Drawing Qty (2) (6) (3) (4/5) TLV3201AIDBVR ACTIVE SOT-23 DBV 5 3000 Green (RoHS NIPDAU Level-2-260C-1 YEAR -40 to 125 RAI & no Sb/Br) TLV3201AIDBVT ACTIVE SOT-23 DBV 5 250 Green (RoHS NIPDAU Level-2-260C-1 YEAR -40 to 125 RAI & no Sb/Br) TLV3201AIDCKR ACTIVE SC70 DCK 5 3000 Green (RoHS NIPDAU Level-2-260C-1 YEAR -40 to 125 SDP & no Sb/Br) TLV3201AIDCKT ACTIVE SC70 DCK 5 250 Green (RoHS NIPDAU Level-2-260C-1 YEAR -40 to 125 SDP & no Sb/Br) TLV3202AID ACTIVE SOIC D 8 50 Green (RoHS NIPDAU Level-2-260C-1 YEAR -40 to 125 TL3202 & no Sb/Br) TLV3202AIDGK ACTIVE VSSOP DGK 8 80 Green (RoHS NIPDAUAG Level-1-260C-UNLIM -40 to 125 VUDC & no Sb/Br) TLV3202AIDGKR ACTIVE VSSOP DGK 8 2500 Green (RoHS NIPDAUAG Level-1-260C-UNLIM -40 to 125 VUDC & no Sb/Br) TLV3202AIDR ACTIVE SOIC D 8 2500 Green (RoHS NIPDAU Level-2-260C-1 YEAR -40 to 125 TL3202 & no Sb/Br) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based flame retardants must also meet the <=1000ppm threshold requirement. (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. Addendum-Page 1

PACKAGE OPTION ADDENDUM www.ti.com 6-Feb-2020 (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF TLV3201, TLV3202 : •Automotive: TLV3201-Q1, TLV3202-Q1 NOTE: Qualified Version Definitions: •Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects Addendum-Page 2

PACKAGE MATERIALS INFORMATION www.ti.com 24-Apr-2020 TAPE AND REEL INFORMATION *Alldimensionsarenominal Device Package Package Pins SPQ Reel Reel A0 B0 K0 P1 W Pin1 Type Drawing Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant (mm) W1(mm) TLV3201AIDBVR SOT-23 DBV 5 3000 178.0 9.0 3.23 3.17 1.37 4.0 8.0 Q3 TLV3201AIDBVT SOT-23 DBV 5 250 178.0 8.4 3.3 3.2 1.4 4.0 8.0 Q3 TLV3201AIDCKR SC70 DCK 5 3000 178.0 9.0 2.4 2.5 1.2 4.0 8.0 Q3 TLV3201AIDCKT SC70 DCK 5 250 178.0 8.4 2.4 2.5 1.2 4.0 8.0 Q3 TLV3202AIDGKR VSSOP DGK 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 TLV3202AIDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 PackMaterials-Page1

PACKAGE MATERIALS INFORMATION www.ti.com 24-Apr-2020 *Alldimensionsarenominal Device PackageType PackageDrawing Pins SPQ Length(mm) Width(mm) Height(mm) TLV3201AIDBVR SOT-23 DBV 5 3000 180.0 180.0 18.0 TLV3201AIDBVT SOT-23 DBV 5 250 180.0 180.0 18.0 TLV3201AIDCKR SC70 DCK 5 3000 190.0 190.0 30.0 TLV3201AIDCKT SC70 DCK 5 250 190.0 190.0 30.0 TLV3202AIDGKR VSSOP DGK 8 2500 364.0 364.0 27.0 TLV3202AIDR SOIC D 8 2500 367.0 367.0 35.0 PackMaterials-Page2

None

None

PACKAGE OUTLINE DBV0005A SOT-23 - 1.45 mm max height SCALE 4.000 SMALL OUTLINE TRANSISTOR C 3.0 2.6 0.1 C 1.75 1.45 1.45 B A 0.90 PIN 1 INDEX AREA 1 5 2X 0.95 3.05 2.75 1.9 1.9 2 4 3 0.5 5X 0.3 0.15 0.2 C A B (1.1) TYP 0.00 0.25 GAGE PLANE 0.22 TYP 0.08 8 TYP 0.6 0 0.3 TYP SEATING PLANE 4214839/E 09/2019 NOTES: 1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. Refernce JEDEC MO-178. 4. Body dimensions do not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not exceed 0.15 mm per side. www.ti.com

EXAMPLE BOARD LAYOUT DBV0005A SOT-23 - 1.45 mm max height SMALL OUTLINE TRANSISTOR PKG 5X (1.1) 1 5 5X (0.6) SYMM (1.9) 2 2X (0.95) 3 4 (R0.05) TYP (2.6) LAND PATTERN EXAMPLE EXPOSED METAL SHOWN SCALE:15X SOLDER MASK SOLDER MASK METAL UNDER METAL OPENING OPENING SOLDER MASK EXPOSED METAL EXPOSED METAL 0.07 MAX 0.07 MIN ARROUND ARROUND NON SOLDER MASK SOLDER MASK DEFINED DEFINED (PREFERRED) SOLDER MASK DETAILS 4214839/E 09/2019 NOTES: (continued) 5. Publication IPC-7351 may have alternate designs. 6. Solder mask tolerances between and around signal pads can vary based on board fabrication site. www.ti.com

EXAMPLE STENCIL DESIGN DBV0005A SOT-23 - 1.45 mm max height SMALL OUTLINE TRANSISTOR PKG 5X (1.1) 1 5 5X (0.6) SYMM 2 (1.9) 2X(0.95) 3 4 (R0.05) TYP (2.6) SOLDER PASTE EXAMPLE BASED ON 0.125 mm THICK STENCIL SCALE:15X 4214839/E 09/2019 NOTES: (continued) 7. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations. 8. Board assembly site may have different recommendations for stencil design. www.ti.com

PACKAGE OUTLINE D0008A SOIC - 1.75 mm max height SCALE 2.800 SMALL OUTLINE INTEGRATED CIRCUIT C SEATING PLANE .228-.244 TYP [5.80-6.19] .004 [0.1] C A PIN 1 ID AREA 6X .050 [1.27] 8 1 2X .189-.197 [4.81-5.00] .150 NOTE 3 [3.81] 4X (0 -15 ) 4 5 8X .012-.020 B .150-.157 [0.31-0.51] .069 MAX [3.81-3.98] .010 [0.25] C A B [1.75] NOTE 4 .005-.010 TYP [0.13-0.25] 4X (0 -15 ) SEE DETAIL A .010 [0.25] .004-.010 0 - 8 [0.11-0.25] .016-.050 [0.41-1.27] DETAIL A (.041) TYPICAL [1.04] 4214825/C 02/2019 NOTES: 1. Linear dimensions are in inches [millimeters]. Dimensions in parenthesis are for reference only. Controlling dimensions are in inches. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not exceed .006 [0.15] per side. 4. This dimension does not include interlead flash. 5. Reference JEDEC registration MS-012, variation AA. www.ti.com

EXAMPLE BOARD LAYOUT D0008A SOIC - 1.75 mm max height SMALL OUTLINE INTEGRATED CIRCUIT 8X (.061 ) [1.55] SYMM SEE DETAILS 1 8 8X (.024) [0.6] SYMM (R.002 ) TYP [0.05] 5 4 6X (.050 ) [1.27] (.213) [5.4] LAND PATTERN EXAMPLE EXPOSED METAL SHOWN SCALE:8X SOLDER MASK SOLDER MASK METAL OPENING OPENING METAL UNDER SOLDER MASK EXPOSED METAL EXPOSED METAL .0028 MAX .0028 MIN [0.07] [0.07] ALL AROUND ALL AROUND NON SOLDER MASK SOLDER MASK DEFINED DEFINED SOLDER MASK DETAILS 4214825/C 02/2019 NOTES: (continued) 6. Publication IPC-7351 may have alternate designs. 7. Solder mask tolerances between and around signal pads can vary based on board fabrication site. www.ti.com

EXAMPLE STENCIL DESIGN D0008A SOIC - 1.75 mm max height SMALL OUTLINE INTEGRATED CIRCUIT 8X (.061 ) [1.55] SYMM 1 8 8X (.024) [0.6] SYMM (R.002 ) TYP [0.05] 5 4 6X (.050 ) [1.27] (.213) [5.4] SOLDER PASTE EXAMPLE BASED ON .005 INCH [0.125 MM] THICK STENCIL SCALE:8X 4214825/C 02/2019 NOTES: (continued) 8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations. 9. Board assembly site may have different recommendations for stencil design. www.ti.com

None

None

IMPORTANTNOTICEANDDISCLAIMER TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you permission to use these resources only for development of an application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these resources. TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for TI products. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2020, Texas Instruments Incorporated