E M C C o m p o n e n t s July 2013 Common Mode Filters For high-speed differential signal line (USB2.0, LVDS, etc.) TCM-G series TCM0605G [0202 inch]* TCM0806G [0302 inch] TCM1608G [0603 inch] * Dimensions Code JIS[EIA]

(2/14) E M C C o m p o n e n t s REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The storage period is less than 6 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 20 to 70% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150°C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/Aviation equipment (8) Public information-processing equipment (2) Transportation equipment (cars, electric trains, ships, etc.) (9) Military equipment (3) Medical equipment (10) Electric heating apparatus, burning equipment (4) Power-generation control equipment (11) Disaster prevention/crime prevention equipment (5) Atomic energy-related equipment (12) Safety equipment (6) Seabed equipment (13) Other applications that are not considered general-purpose (7) Transportation control equipment applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. 001-01 / 20130723 / e9712_tcm_g.fm

(3/14) E M C C o m p o n e n t s Common Mode Filters Product compatible with RoHS directive Halogen-free Compatible with lead-free solders For high-speed differential signal line (USB2.0, LVDS, etc.) Overview of the TCM-G Series FEATURES Thin-film common mode filter based on the thin-film processing techniques and material technology cultivated from HDD head manufacturing. Has EMC suppression by achieving wide frequency range (cutoff frequency of 3GHz or higher) differential mode transmission while ensuring common mode impedance with virtually no affect on the high-speed differential transmission line signal. Lineup includes the compact 0605 size (0.65×0.50×0.30mm) and 1608 (1.60×0.80×0.40mm) array type, etc. APPLICATION Noise countermeasure for high-speed differential interfaces (USB2.0, LVDS, MIPI, etc.) for mobile devices and general consumer products such as smart phones, tablets, digital cameras, and portable music players. PART NUMBER CONSTRUCTION TCM 0605 - G - 900 - 2P - T □□□ L×W×T Dimensions Product internal Impedance Internal Series name Number of lines Packaging style (mm) code ((cid:4)) at 100MHz code 0605 0.65×0.50×0.30 G 201 200 2P 2 lines T Taping 0806 0.85×0.65×0.40 151 150 4P 4 lines 1608 1.60×0.80×0.40 900 90 650 65 350 35 OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Temperature range Type Operating Storage temperature(cid:2) Package quantity Individual weight temperature （°C） （°C） （pieces/reel） （mg） TCM0605G –25 to +85 –25 to +85 10,000 0.5 TCM0806G –25 to +85 –25 to +85 10,000 1.0 TCM1608G –25 to +85 –25 to +85 4,000 4.0 (cid:2)(cid:3)The Storage temperature range is for after the circuit board is mounted. RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://www.tdk.co.jp/rohs/ Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm. • All specifications are subject to change without notice. 001-01 / 20130723 / e9712_tcm_g.fm

(4/14) E M C C o m p o n e n t s Overview of the TCM-G Series RECOMMENDED REFLOW PROFILE Preheating Soldering Natural cooling Peak T4 e ur T3 T3 at er p m e T T2 T: t3 T1 t1 t2 t: Time Preheating Soldering Peak Temp. Time Temp. Time Temp. Time T1 T2 t1 T3 t2 T4 t3 150°C 180°C 60 to 120s 230°C 10 to 30s 245°C 5s max. • All specifications are subject to change without notice. 001-01 / 20130723 / e9712_tcm_g.fm

(5/14) E M C C o m p o n e n t s TCM-G series TCM0605G Type SHAPE & DIMENSIONS 0.50±0.05 1 4 5 0 0. ± 5 6 0. 2 3 p. y 5t 05 0.1 0. ± 0 3 0. 0.45±0.05 0.20±0.05 0.15±0.05 Dimensions in mm RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM 0.8 1 4 3 2 0. 2 3 1 5 7 2 0. 0. •No polarity 0.3 0.2 Dimensions in mm • All specifications are subject to change without notice. 001-01 / 20130723 / e9712_tcm_g.fm

(6/14) E M C C o m p o n e n t s TCM-G TCM0605G Type series　 ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Common mode impedance Insulation DC resistance Rated current Rated voltage [at 100MHz] resistance Part No. ((cid:4))[1 line] (A)max. (V)max. ((cid:4)) Tolerance (M(cid:4))min. 65 ±20% 2.7±30% 0.1 10 10 TCM0605G-650-2P-T□□□ 90 ±20% 3.0±30% 0.1 10 10 TCM0605G-900-2P-T□□□ ○Measurement equipment Measurement item Product No. Manufacturer Common mode impedance 4291A Agilent Technologies DC resistance 4338A Agilent Technologies Insulation resistance 4339A Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 001-01 / 20130723 / e9712_tcm_g.fm

(7/14) E M C C o m p o n e n t s TCM-G TCM0605G Type series　 ELECTRICAL CHARACTERISTICS IMPEDANCE VS. FREQUENCY CHARACTERISTICS 10000 900 Common mode 1000 650 Common mode Ω) (e c n100 a d e p m I 10 900 Differential mode 650 Differential mode 1 1 10 100 1000 10000 Frequency (MHz) ○Measurement equipment Product No. Manufacturer E4991A Agilent Technologies ＊ Equivalent measurement equipment may be used. INSERTION LOSS VS. FREQUENCY CHARACTERISTICS 0 650 Differential mode 650 Common mode 900 Differential mode 5 900 Common mode 10 )B 15 d (s s o n l 20 o serti 25 n I 30 35 40 1 10 100 1000 10000 Frequency (MHz) ○Measurement equipment Product No. Manufacturer E5071B Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 001-01 / 20130723 / e9712_tcm_g.fm

(8/14) E M C C o m p o n e n t s TCM-G series TCM0806G Type SHAPE & DIMENSIONS 0.65±0.05 1 4 5 0 0. ± 5 8 0. 2 3 p. y ±0.05 0.15t 0 4 0. 0 1 0. 0 ± 1 0.50 7±0. 2 0. Dimensions in mm 0.20+–00..1005 RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM 0.9 1 4 3 0. 2 3 8 2 0. 0. •No polarity 0.3 0.3 Dimensions in mm • All specifications are subject to change without notice. 001-01 / 20130723 / e9712_tcm_g.fm

(9/14) E M C C o m p o n e n t s TCM-G TCM0806G Type series　 ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Common mode impedance Insulation DC resistance Rated current Rated voltage [at 100MHz] resistance Part No. ((cid:4))[1 line] (A)max. (V)max. ((cid:4)) Tolerance (M(cid:4))min. 35 ±30% 1.15±30% 0.10 10 10 TCM0806G-350-2P-T□□□ 65 ±20% 2.50±30% 0.10 10 10 TCM0806G-650-2P-T□□□ 90 ±20% 2.70±30% 0.10 10 10 TCM0806G-900-2P-T□□□ 150 ±20% 3.50±30% 0.05 10 10 TCM0806G-151-2P-T□□□ ○Measurement equipment Measurement item Product No. Manufacturer Common mode impedance 4291A Agilent Technologies DC resistance 4338A Agilent Technologies Insulation resistance 4339A Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 001-01 / 20130723 / e9712_tcm_g.fm

(10/14) E M C C o m p o n e n t s TCM-G TCM0806G Type series　 ELECTRICAL CHARACTERISTICS IMPEDANCE VS. FREQUENCY CHARACTERISTICS 10000 151 Common mode 1000 900 Common mode Ω) 650 Common mode (e c 350 Common mode n100 a d e p m I 900 Differential mode 650 Differential mode 10 350 Differential mode 151 Differential mode 1 1 10 100 1000 10000 Frequency (MHz) ○Measurement equipment Product No. Manufacturer E4991A Agilent Technologies ＊ Equivalent measurement equipment may be used. INSERTION LOSS VS. FREQUENCY CHARACTERISTICS 0 350 Differential mode 5 900 Differential mode 650 Differential mode 10 )B 15 d (s s o n l 20 sertio 25 650 Common mode 350 Common mode n I 30 151 Common mode 900 Common mode 151 Differential mode 35 40 1 10 100 1000 10000 Frequency (MHz) ○Measurement equipment Product No. Manufacturer E5071B Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 001-01 / 20130723 / e9712_tcm_g.fm

(11/14) E M C C o m p o n e n t s TCM-G series TCM1608G Type SHAPE & DIMENSIONS 0.80±0.10 1 8 0 2 7 1 0. ± 0 1.6 3 6 4 5 p. y 0 5t 1 1 0. 0. ± 0 4 0. 0 1 0. ± 0 4 0. 0 1 0. ± 0 2 0. Dimensions in mm 0.16±0.10 RECOMMENDED LAND PATTERN CIRCUIT DIAGRAM 1.42 1 8 0.48 2 7 4 0. 3 6 4 5 2 •No polarity 0. Dimensions in mm • All specifications are subject to change without notice. 001-01 / 20130723 / e9712_tcm_g.fm

(12/14) E M C C o m p o n e n t s TCM-G TCM1608G Type series　 ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Common mode impedance Insulation DC resistance Rated current Rated voltage [at 100MHz] resistance Part No. ((cid:4))[1 line] (A)max. (V)max. ((cid:4)) Tolerance (M(cid:4))min. 35 ±30% 0.85±30% 0.10 5 10 TCM1608G-350-4P-T□□□ 65 ±20% 1.30±30% 0.10 5 10 TCM1608G-650-4P-T□□□ 90 ±20% 1.50±30% 0.10 5 10 TCM1608G-900-4P-T□□□ 200 ±20% 4.00±30% 0.05 5 10 TCM1608G-201-4P-T□□□ ○Measurement equipment Measurement item Product No. Manufacturer Common mode impedance 4291A Agilent Technologies DC resistance 4338A Agilent Technologies Insulation resistance 4339A Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 001-01 / 20130723 / e9712_tcm_g.fm

(13/14) E M C C o m p o n e n t s TCM-G TCM1608G Type series　 ELECTRICAL CHARACTERISTICS IMPEDANCE VS. FREQUENCY CHARACTERISTICS 10000 201 Common mode 1000 900 Common mode Ω) 650 Common mode (e 350 Common mode c n100 a d e p m 201 Differential mode I 900 Differential mode 10 650 Differential mode 350 Differential mode 1 1 10 100 1000 10000 Frequency (MHz) ○Measurement equipment Product No. Manufacturer E4991A Agilent Technologies ＊ Equivalent measurement equipment may be used. INSERTION LOSS VS. FREQUENCY CHARACTERISTICS 0 201 Differential mode 5 350 Differential mode 900 Differential mode 10 650 Differential mode )B 15 d (s s o n l 20 o serti 25 900 Common mode 350 Common mode n I 650 Common mode 30 201 Common mode 35 40 1 10 100 1000 10000 Frequency (MHz) ○Measurement equipment Product No. Manufacturer E5071B Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 001-01 / 20130723 / e9712_tcm_g.fm

(14/14) E M C C o m p o n e n t s TCM-G series Packaging style REEL DIMENSIONS 2.0±0.5 +1–0 0 6 ø 1.0 ø13±0.2 9+0.3 ø21±0.8 13+1.4 ø180+–30 Dimensions in mm TAPE DIMENSIONS TCM0605G TCM0806G, 2.0 4.0 ø1.5 5 TCM1608G 7 1. 5 3. 8.0 B A P1 K K Dimensions in mm Type A B P1 K TCM0605G 0.63 0.77 2.0 0.35 TCM0806G 0.74 0.94 2.0 0.50 TCM1608G 1.00 1.80 4.0 0.50 160min. Taping 200min. Drawing direction 300min. Dimensions in mm • All specifications are subject to change without notice. 001-01 / 20130723 / e9712_tcm_g.fm