TAW Series Tantalum Solid Electrolytic Fused Capacitors • Thin film fuse connected in series with capacitor • Protection from possible damaging from high DC leakage current (short circuit failure) • CV range: 6.8-100μF / 10-50V • Application: servers LEAD-FREE COMPATIBLE COMPONENT CASE DIMENSIONS:millimeters (inches) EIA EIA L±0.20 W+0.20 (0.008) H+0.20 (0.008) W±0.20 A+0.30 (0.012) Code 1 S Min. Code Metric (0.008) -0.10 (0.004) –0.10 (0.004) (0.008) -0.20 (0.008) D 2917 7343-31 7.30 (0.287) 4.30 (0.169) 2.90 (0.114) 2.40 (0.094) 1.30 (0.051) 4.40 (0.173) W dimension applies to the termination width for A dimensional area only. 1 For part marking see page 169 HOW TO ORDER TAW D 476 * 010 R 0500 Type Case Size Capacitance Code Tolerance Rated DC Voltage Packaging ESR in mΩ See table pF code: 1st two K=±10% 010=10Vdc R = Pure Tin 7" Reel above digits represent M=±20% 016=16Vdc S = Pure Tin 13" Reel significant figures 020=20Vdc 3rd digit represents 025=25Vdc multiplier (number of 035=35Vdc zeros to follow) 050=50Vdc TECHNICAL SPECIFICATIONS Technical Data: All technical data relate to an ambient temperature of +25°C Capacitance Range: 6.8 μF to 100 μF Capacitance Tolerance: ±10%; ±20% Rated Voltage (V ) (cid:2)+85°C: 10 16 20 25 35 50 R Category Voltage (V ) (cid:2)+125°C: 7 10 13 17 23 33 C Surge Voltage (V) (cid:2)+85°C: 13 20 26 32 46 65 s Surge Voltage (V) (cid:2)+125°C: 8 13 16 20 28 40 s Fuse Off I > 4A in 1s, insulating resistance > 10MΩ Fuse Continuous Current Capability 0.75A Temperature Range: -55°C to +125°C Reliability: 1% per 1000 hours at 85°C, Vr with 0.1Ω/V series impedance, 60% confidence level 114 ■ JANUARY 2014

TAW Series Tantalum Solid Electrolytic Fused Capacitors CAPACITANCE AND RATED VOLTAGE RANGE (LETTER DENOTES CASE SIZE) Capacitance Rated Voltage DC (V ) to 85°C R μF Code 6.3V (J) 10V (A) 16V (C) 20V (D) 25V (E) 35V (V) 50V (T) 1.0 105 2.2 225 4.7 475 6.8 685 D(600) D(700) 10 106 D(600) D(600) D(700) 22 226 D(500) D(600) 33 336 D(600) D(500) 47 476 D(500) D(800) 100 107 D(500) Available Ratings (ESR ratings in mOhms in brackets) Engineering samples - please contact manufacturer *Codes under development – subject to change Note: Voltage ratings are minimum values. AVX reserves the right to supply higher ratings in the same case size, to the same reliability standards. RATINGS & PART NUMBER REFERENCE Rated DCL DF ESR 100kHz RMS Current (mA) 100kHz RMS Voltage (mV) AVX Case Capacitance Voltage (μA) % Max. (mΩ) MSL Part No. Size (μF) (V) Max. Max. @100kHz 25ºC 85ºC 125ºC 25ºC 85ºC 125ºC 10 Volt @ 85ºC (7 Volt @ 125ºC) TAWD476*010#0500 D 47 10 4.7 6 500 1 548 493 219 274 246 110 TAWD107*010#0500 D 100 10 10 8 500 1 548 493 219 274 246 110 16 Volt @ 85°C (10 Volt @ 125°C) TAWD336*016#0600 D 33 16 5.3 6 600 1 500 450 200 300 270 120 TAWD476*016#0800 D 47 16 7.5 7 800 1 433 390 173 346 312 139 20 Volt @ 85ºC (13 Volt @ 125ºC) TAWD226*020#0500 D 22 20 4.4 6 500 1 548 493 219 274 246 110 TAWD336*020#0500 D 33 20 6.6 6 500 1 548 493 219 274 246 110 25 Volt @ 85ºC (17 Volt @ 125ºC) TAWD106*025#0600 D 10 25 2.5 6 600 1 500 450 200 300 270 120 TAWD226*025#0600 D 22 25 5.5 6 600 1 500 450 200 300 270 120 35 Volt @ 85ºC (23 Volt @ 125ºC) TAWD685*035#0600 D 6.8 35 2.4 6 600 1 500 450 200 300 270 120 TAWD106*035#0600 D 10 35 3.5 6 600 1 500 450 200 300 270 120 50 Volt @ 85ºC (33 Volt @ 125ºC) TAWD685*050#0700 D 6.8 50 3.4 6 700 1 463 417 185 324 292 130 TAWD106*050#0700 D 10 50 5 6 700 1 463 417 185 324 292 130 Moisture Sensitivity Level (MSL) is defined according to J-STD-020. TYPICAL FUSE ACTUATION All technical data relates to an ambient temperature of +25°C. Capacitance and DF are measured at 120Hz, 0.5V RMS with a maximum DC bias of 2.2 volts. DCL is measured at rated voltage after 5 minutes. Typical Actuation Time vs Load Current For typical weight and composition see page 162. 100.000 NOTE: AVX reserves the right to supply a higher voltage rating or tighter tolerance part in the same case size, to the same reliability standards. s] 10.000 m e [ 1.000 m Ti n 0.100 o uati 0.010 ct A 0.001 1 10 Current [A] 100 Note: for a different fuse characteristic requirements please contact manufacturer JANUARY 2014 ■ 115