T97 www.vishay.com Vishay Sprague Solid Tantalum Chip Capacitors TANTAMOUNT™, Hi-Rel COTS, Ultra-Low ESR, Conformal Coated Case FEATURES • High reliability; Weibull failure rate gradin g available • Surge current testing per MIL-PRF-55365 Available options available Available • Ultra-low ESR • Tin / lead (SnPb) termination available • Mounting: surface mount • Material categorization: for definitions of complianc e please see www.vishay.com/doc?99912 Note * This datasheet provides information about parts that are RoHS-compliant and / or parts that are non RoHS-compliant. For example, parts with lead (Pb) terminations are not RoHS-compliant. Please see the information / tables in this datasheet for details PERFORMANCE CHARACTERISTICS www.vishay.com/doc?40209 Capacitance Tolerance: ± 10 %, ± 20 % standard Operating Temperature: -55 °C to +125 °C Voltage Rating: 4 V to 75 V DC DC (above 85 °C, voltage derating is required) Moisture Sensitivity Level 2a Capacitance Range: 10 μF to 2200 μF ORDERING INFORMATION T97 R 227 K 020 E S A TYPE CASE CAPACITANCE CAPACITANCE DC VOLTAGE RATING TERMINATION / RELIABILITY SURGE CODE TOLERANCE AT +85 °C PACKAGING LEVEL CURRENT (available options are series dependent) See This is expressed in K = ± 10 % This is expressed in E = Sn / Pb solder / A = 1.0 % A = 10 cycles Ratings pF. The first two M = ± 20 % volts. To complete the 7" (178 mm) reel Weibull at +25 °C and digits are the three-digit block, L = Sn / Pb solder / B = 0.1 % B = 10 cycles Case significant figures. zeros precede the 7" (178 mm), 1/2 reel Weibull (1) at -55 °C / Code The third is the voltage rating. A C = 100 % tin / S = 40 h +85 °C table number of zeros decimal point is 7" (178 mm), reel burn-in S = 3 cycles to follow. indicated by an “R” H = 100 % tin / Z = non- at 25 °C (6R3 = 6.3 V). 7" (178 mm), 1/2 reel established reliability Notes (1) Available on select ratings. See “Standard Ratings” table • We reserve the right to supply higher voltage ratings and tighter capacitance tolerance capacitors in the same case size. Low ESR solid tantalum chip capacitors allow delta ESR of 1.25 times the datasheet limits after mounting Revision: 01-Apr-2019 1 Document Number: 40092 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

T97 www.vishay.com Vishay Sprague DIMENSIONS in inches [millimeters] Tantalum wire J nib identifies W anode (+) terminal L D H B A CASE CODE L (MAX.) W H A B D (REF.) J (MAX.) 0.299 0.173 ± 0.016 0.079 0.051 ± 0.012 0.181 ± 0.024 0.252 0.004 V [7.6] [4.4 ± 0.4] [2.0 max.] [1.3 ± 0.3] [4.6 ± 0.6] [6.4] [0.1] 0.299 0.173 ± 0.016 0.138 0.051 ± 0.012 0.181 ± 0.024 0.252 0.004 D [7.6] [4.4 ± 0.4] [3.5 max.] [1.3 ± 0.3] [4.6 ± 0.6] [6.4] [0.1] 0.299 0.173 ± 0.016 0.157 ± 0.016 0.051 ± 0.012 0.181 ± 0.024 0.252 0.004 E [7.6] [4.4 ± 0.4] [4.0 ± 0.4] [1.3 ± 0.3] [4.6 ± 0.6] [6.4] [0.1] 0.299 0.238 ± 0.016 0.142 ± 0.016 0.051 ± 0.012 0.181 ± 0.024 0.244 0.004 R [7.6] [6.0 ± 0.4] [3.6 ± 0.4] [1.3 ± 0.3] [4.6 ± 0.6] [6.2] [0.1] 0.299 0.238 ± 0.016 0.185 ± 0.016 0.055 ± 0.016 0.181 ± 0.024 0.244 0.004 F [7.6] [6.0 ± 0.4] [4.7 ± 0.4] [1.4 ± 0.4] [4.6 ± 0.6] [6.2] [0.1] 0.299 0.238 ± 0.016 0.236 ± 0.016 0.055 ± 0.016 0.181 ± 0.024 0.244 0.004 Z [7.6] [6.0 ± 0.4] [6.0 ± 0.4] [1.4 ± 0.4] [4.6 ± 0.6] [6.2] [0.1] 0.315 0.260 + 0.016 / - 0.024 0.142 ± 0.016 0.051 ± 0.012 0.197 ± 0.024 0.260 0.004 M [8.0] [6.6 + 0.4 / - 0.6] [3.6 ± 0.4] [1.3 ± 0.3] [5.0 ± 0.6] [6.6] [0.1] 0.315 0.260 + 0.016 / - 0.024 0.205 ± 0.016 0.055 ± 0.016 0.197 ± 0.024 0.260 0.004 H [8.0] [6.6 + 0.4 / - 0.6] [5.2 ± 0.4] [1.4 ± 0.4] [5.0 ± 0.6] [6.6] [0.1] 0.315 0.260 + 0.016 / - 0.024 0.252 ± 0.016 0.056 ± 0.017 0.196 ± 0.025 0.259 0.004 N [8.0] [6.6 + 0.4 / - 0.6] [6.4 ± 0.4] [1.4 ± 0.4] [5.0 ± 0.6] [6.6] [0.1] Note • The anode termination (D less B) will be a minimum of 0.012" [0.3 mm] RATINGS AND CASE CODES μF 4 V 6.3 V 10 V 16 V 20 V 25 V 35 V 40 V 50 V 63 V 75 V 10 D R 15 E / R R R / F 22 R F Z / H 33 F Z 47 R Z / N 68 R F 100 F F / H H 150 F 220 E R M 330 V E F H / F 470 V E E H H 680 E E R H 1000 E / R R F 1500 R F 2200 R Revision: 01-Apr-2019 2 Document Number: 40092 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

T97 www.vishay.com Vishay Sprague STANDARD RATINGS MAX. DF MAX. ESR MAX. MAX. DCL AVAILABLE CAPACITANCE AT +25 °C AT +25 °C RIPPLE CASE CODE PART NUMBER AT +25 °C RELIABILITY (μF) 120 Hz 100 kHz 100 kHz (μA) LEVELS (%) (m) IRMS (A) 4 V AT +85 °C; 2.7 V AT +125 °C DC DC 470 V T97V477(1)004(2)(4)(5) 18.8 8 60 2.2 A, B, S, Z 680 E T97E687(1)004(2)(4)(5) 27.2 6 25 2.9 A, B, S, Z 1000 E T97E108(1)004(2)(4)(5) 40.0 8 20 3.3 A, B, S, Z 1000 R T97R108(1)004(2)(4)(5) 40.0 8 18 3.7 A, B, S, Z 1500 R T97R158(1)004(2)(4)(5) 60.0 8 24 2.9 A, B, S, Z 2200 R T97R228(1)004(2)(4)(5) 88.0 30 35 2.7 A, B, S, Z 6.3 V AT +85 °C; 4 V AT +125 °C DC DC 330 V T97V337(1)6R3(2)(4)(5) 20.8 8 56 2.0 A, B, S, Z 470 E T97E477(1)6R3(2)(4)(5) 29.6 6 30 2.7 A, B, S, Z 680 E T97E687(1)6R3(2)(4)(5) 42.8 6 25 2.9 A, B, S, Z 1000 R T97R108(1)6R3(2)(4)(5) 63.0 8 31 2.8 A, B, S, Z 1500 F T97F158(1)6R3(2)(4)(5) 94.0 30 35 2.7 A, B, S, Z 10 V AT +85 °C; 7 V AT +125 °C DC DC 330 E T97E337(1)010(2)(4)(5) 33.0 6 35 2.5 A, B, S, Z 470 E T97E477(1)010(2)(4)(5) 47.0 6 28 2.8 A, B, S, Z 680 R T97R687(1)010(2)(6)(5) 68.0 6 28 3.0 S, Z 1000 F T97F108(1)010(2)(3)(5) 100.0 20 120 1.4 A, S, Z 16 V AT +85 °C; 10 V AT +125 °C DC DC 220 E T97E227(1)016(2)(4)(5) 35.2 8 60 2.3 A, B, S, Z 330 F T97F337(1)016(2)(4)(5) 52.8 10 100 1.6 A, B, S, Z 470 H T97H477(1)016(2)(4)(5) 75.2 14 100 1.4 A, B, S, Z 680 H T97H687(1)016(2)(4)(5) 100.0 20 80 1.8 A, B, S, Z 20 V AT +85 °C; 13 V AT +125 °C DC DC 220 R T97R227(1)020(2)(4)(5) 44.0 8 80 1.8 A, B, S, Z 330 F T97F337(1)020(2)(6)(5) 66.0 10 100 1.6 S, Z 330 H T97H337(1)020(2)(4)(5) 66.0 10 100 1.6 A, B, S, Z 470 H T97H477(1)020(2)(3)(5) 94.0 14 100 1.6 A, S, Z 25 V AT +85 °C; 17 V AT +125 °C DC DC 68 R T97R686(1)025(2)(4)(5) 17.0 6 100 1.6 A, B, S, Z 100 F T97F107(1)025(2)(4)(5) 25.0 8 100 1.6 A, B, S, Z 150 F T97F157(1)025(2)(4)(5) 37.5 8 80 1.8 A, B, S, Z 220 M T97M227(1)025(2)(3)(5) 55.0 8 100 1.6 A, S, Z 35 V AT +85 °C; 23 V AT +125 °C DC DC 47 R T97R476(1)035(2)(4)(5) 16.5 6 100 1.6 A, B, S, Z 68 F T97F686(1)035(2)(3)(5) 23.8 6 100 1.6 A, S, Z 100 F T97F107M035(2)(3)(5) 35.0 8 100 1.6 A, S, Z 100 H T97H107(1)035(2)(3)(5) 35.0 8 100 1.4 A, S, Z Note • Part number definitions: (1) Capacitance tolerance: K, M (2) Termination and packaging: C, E, H, L (3) Reliability level: A, S, Z (4) Reliability level: A, B, S, Z (5) Surge current: A, B, S (6) Reliability level: S, Z Revision: 01-Apr-2019 3 Document Number: 40092 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

T97 www.vishay.com Vishay Sprague STANDARD RATINGS MAX. DF MAX. ESR MAX. MAX. DCL AVAILABLE CAPACITANCE AT +25 °C AT +25 °C RIPPLE CASE CODE PART NUMBER AT +25 °C RELIABILITY (μF) 120 Hz 100 kHz 100 kHz (μA) LEVELS (%) (m) IRMS (A) 40 V AT +85 °C; 26 V AT +125 °C DC DC 100 H T97H107M040(2)(6)(5) 40.0 10 150 1.3 S, Z 50 V AT +85 °C; 33 V AT +125 °C DC DC 15 E T97E156(1)050(2)(4)(5) 7.5 6 350 0.9 A, B, S, Z 15 R T97R156(1)050(2)(4)(5) 7.5 6 250 1.0 A, B, S, Z 22 R T97R226(1)050(2)(4)(5) 11.0 6 220 1.1 A, B, S, Z 33 F T97F336(1)050(2)(3)(5) 16.5 6 150 1.3 A, S, Z 47 Z T97Z476(1)050(2)(6)(5) 23.5 6 240 1.1 S, Z 47 N T97N476(1)050(2)(4)(5) 23.5 6 150 1.4 A, B, S, Z 63 V AT +85 °C; 42 V AT +125 °C DC DC 10 D T97D106(1)063(2)(3)(5) 10.0 6 400 0.6 A, S, Z 15 R T97R156(1)063(2)(4)(5) 9.5 6 400 0.8 A, B, S, Z 22 F T97F226(1)063(2)(3)(5) 13.9 6 250 1.0 A, S, Z 33 Z T97Z336(1)063(2)(3)(5) 20.8 8 500 0.7 A, S, Z 75 V AT +85 °C; 50 V AT +125 °C DC DC 10 R T97R106(1)075(2)(6)(5) 7.5 6 500 0.7 S, Z 15 R T97R156M075(2)(6)(5) 12 6 500 0.7 S, Z 15 F T97F156M075(2)(6)(5) 12 6 500 0.7 S, Z 22 Z T97Z226(1)075(2)(6)(5) 16.5 6 400 0.8 S, Z 22 H T97H226(1)075(2)(6)(5) 16.5 6 400 0.8 S, Z Note • Part number definitions: (1) Capacitance tolerance: K, M (2) Termination and packaging: C, E, H, L (3) Reliability level: A, S, Z (4) Reliability level: A, B, S, Z (5) Surge current: A, B, S (6) Reliability level: S, Z TYPICAL CURVES ESR AND Z VS. FREQUENCY 1500 μF -4 V, Case Size “R” 330 μF -10 V, Case Size “E” 1 10000 1 10000 R (Ω) 1000 R (Ω) Z 1000 2nd lineance / ES 0.1 Z 1st line2nd line 2nd lineance / ES 0.1 ESR 1st line2nd line ed 100 ed 100 p p m m I ESR I 0.01 10 0.01 10 0.1 1 10 100 1000 0.1 1 10 100 1000 Frequency (kHz) Frequency (kHz) Revision: 01-Apr-2019 4 Document Number: 40092 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

T97 www.vishay.com Vishay Sprague TYPICAL CURVES ESR AND Z VS. FREQUENCY 330 μF -6.3 V, Case Size “V” 1000 μF -6.3 V, Case Size “R” 10 10000 1 10000 R (Ω) 1 1000 R (Ω) 1000 2nd lineance / ES Z 1st line2nd line 2nd lineance / ES 0.1 Z 1st line2nd line ed 0.1 100 ed 100 p p Im ESR Im ESR 0.01 10 0.01 10 0.1 1 10 100 1000 0.1 1 10 100 1000 Frequency (kHz) Frequency (kHz) 470 μF -4 V, Case Size “V” 10 10000 R (Ω) 1 1000 2nd lineance / ES Z 1st line2nd line ped 0.1 ESR 100 m I 0.01 10 0.1 1 10 100 1000 Frequency (kHz) POWER DISSIPATION CASE CODE MAXIMUM PERMISSIBLE POWER DISSIPATION AT +25 °C (W) IN FREE AIR V 0.141 D 0.215 E 0.240 R, F, M 0.250 Z 0.265 H 0.265 N 0.280 Revision: 01-Apr-2019 5 Document Number: 40092 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

T97 www.vishay.com Vishay Sprague STANDARD PACKAGING QUANTITY UNITS PER REEL CASE CODE 7" FULL REEL 7" HALF REEL V 1000 500 D 400 200 E 500 250 R 300 150 F 250 125 Z 250 125 M 200 100 H 200 100 N 200 100 PRODUCT INFORMATION Conformal Coated Guide Pad Dimensions www.vishay.com/doc?40150 Packaging Dimensions Moisture Sensitivity (MSL) www.vishay.com/doc?40135 SELECTOR GUIDES Solid Tantalum Selector Guide www.vishay.com/doc?49053 Solid Tantalum Chip Capacitors www.vishay.com/doc?40091 FAQ Frequently Asked Questions www.vishay.com/doc?40110 Revision: 01-Apr-2019 6 Document Number: 40092 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Conformal Coated Guide www.vishay.com Vishay Sprague Guide for Conformal Coated Tantalum Capacitors INTRODUCTION Rating for rating, tantalum capacitors tend to have as much as three times better capacitance / volume efficiency than Tantalum electrolytic capacitors are the preferred choice in aluminum electrolytic capacitors. An approximation of the applications where volumetric efficiency, stable electrical capacitance / volume efficiency of other types of capacitors parameters, high reliability, and long service life are primary may be inferred from the following table, which shows the considerations. The stability and resistance to elevated dielectric constant ranges of the various materials used in temperatures of the tantalum / tantalum oxide / manganese each type. Note that tantalum pentoxide has a dielectric dioxide system make solid tantalum capacitors an constant of 26, some three times greater than that of appropriate choice for today's surface mount assembly aluminum oxide. This, in addition to the fact that extremely technology. thin films can be deposited during the electrolytic process Vishay Sprague has been a pioneer and leader in this field, mentioned earlier, makes the tantalum capacitor extremely producing a large variety of tantalum capacitor types for efficient with respect to the number of microfarads available consumer, industrial, automotive, military, and aerospace per unit volume. The capacitance of any capacitor is electronic applications. determined by the surface area of the two conducting Tantalum is not found in its pure state. Rather, it is plates, the distance between the plates, and the dielectric commonly found in a number of oxide minerals, often in constant of the insulating material between the plates. combination with Columbium ore. This combination is known as “tantalite” when its contents are more than COMPARISON OF CAPACITOR one-half tantalum. Important sources of tantalite include DIELECTRIC CONSTANTS Australia, Brazil, Canada, China, and several African countries. Synthetic tantalite concentrates produced from e DIELECTRIC tin slags in Thailand, Malaysia, and Brazil are also a DIELECTRIC CONSTANT significant raw material for tantalum production. Air or vacuum 1.0 Electronic applications, and particularly capacitors, Paper 2.0 to 6.0 consume the largest share of world tantalum production. Other important applications for tantalum include cutting Plastic 2.1 to 6.0 tools (tantalum carbide), high temperature super alloys, Mineral oil 2.2 to 2.3 chemical processing equipment, medical implants, and military ordnance. Silicone oil 2.7 to 2.8 Vishay Sprague is a major user of tantalum materials in the Quartz 3.8 to 4.4 form of powder and wire for capacitor elements and rod and Glass 4.8 to 8.0 sheet for high temperature vacuum processing. Porcelain 5.1 to 5.9 THE BASICS OF TANTALUM CAPACITORS Mica 5.4 to 8.7 Most metals form crystalline oxides which are Aluminum oxide 8.4 non-protecting, such as rust on iron or black oxide on copper. A few metals form dense, stable, tightly adhering, Tantalum pentoxide 26 electrically insulating oxides. These are the so-called “valve” Ceramic 12 to 400K metals and include titanium, zirconium, niobium, tantalum, hafnium, and aluminum. Only a few of these permit the In the tantalum electrolytic capacitor, the distance between accurate control of oxide thickness by electrochemical the plates is very small since it is only the thickness of the means. Of these, the most valuable for the electronics tantalum pentoxide film. As the dielectric constant of the industry are aluminum and tantalum. tantalum pentoxide is high, the capacitance of a tantalum Capacitors are basic to all kinds of electrical equipment, capacitor is high if the area of the plates is large: from radios and television sets to missile controls and eA C = ------- automobile ignitions. Their function is to store an electrical t charge for later use. where Capacitors consist of two conducting surfaces, usually C = capacitance metal plates, whose function is to conduct electricity. They e = dielectric constant are separated by an insulating material or dielectric. The dielectric used in all tantalum electrolytic capacitors is A = surface area of the dielectric tantalum pentoxide. t = thickness of the dielectric Tantalum pentoxide compound possesses high-dielectric Tantalum capacitors contain either liquid or solid strength and a high-dielectric constant. As capacitors are electrolytes. In solid electrolyte capacitors, a dry material being manufactured, a film of tantalum pentoxide is applied (manganese dioxide) forms the cathode plate. A tantalum to their electrodes by means of an electrolytic process. The lead is embedded in or welded to the pellet, which is in turn film is applied in various thicknesses and at various voltages connected to a termination or lead wire. The drawings show and although transparent to begin with, it takes on different the construction details of the surface mount types of colors as light refracts through it. This coloring occurs on the tantalum capacitors shown in this catalog. tantalum electrodes of all types of tantalum capacitors. Revision: 11-Oct-2018 1 Document Number: 40150 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Conformal Coated Guide www.vishay.com Vishay Sprague SOLID ELECTROLYTE TANTALUM CAPACITORS TYPE 194D Solid electrolyte capacitors contain manganese dioxide, which is formed on the tantalum pentoxide dielectric layer SnPb or Gold Plated Ni Cathode by impregnating the pellet with a solution of manganous End Cap Termination Encapsulation nitrate. The pellet is then heated in an oven, and the manganous nitrate is converted to manganese dioxide. SnPb or Gold Plated Ni Anode End Cap Termination The pellet is next coated with graphite, followed by a layer Cathode of metallic silver, which provides a conductive surface Backfill between the pellet and the can in which it will be enclosed. After assembly, the capacitors are tested and inspected to assure long life and reliability. It offers excellent reliability and high stability for consumer and commercial electronics Conductive Silver with the added feature of low cost. Epoxy Adhesive Surface mount designs of “Solid Tantalum” capacitors use Sintered Tantalum Sponge Teflon lead frames or lead frameless designs as shown in the Pellet accompanying drawings. MnO/Carbon/ Anode Backfill 2 Silver Coating TANTALUM CAPACITORS FOR ALL DESIGN CONSIDERATIONS TYPE T96 Solid electrolyte designs are the least expensive for a given rating and are used in many applications where their very Intermediate Fuse small size for a given unit of capacitance is of importance. Cathode They will typically withstand up to about 10 % of the rated Silver DC working voltage in a reverse direction. Also important are their good low temperature performance characteristics and freedom from corrosive electrolytes. Vishay Sprague patented the original solid electrolyte capacitors and was the first to market them in 1956. Vishay Sprague has the broadest line of tantalum capacitors and has continued its position of leadership in this field. Data sheets covering the various types and styles of Vishay Cathode Termination MnO/Carbon/ Sprague capacitors for consumer and entertainment (Silver + Ni/Sn or 2 Silver Coating electronics, industry, and military applications are available Ni/SnPb Plating) where detailed performance characteristics must be Encapsulation Epoxy Tower/ specified. Anode Termination Sponge Teflon (Silver + Ni/Sn or Sintered Tantalum TYPE 195D, 572D, 591D, 592D / W, 594D, Ni/SnPb Plating) Pellet 595D, 695D, T95, 14002 Cathode Termination TYPE T98 (Silver + Ni/Sn/Plating) Encapsulation Fuse Anode Termination Intermediate (Silver + Ni/Sn/Plating) Cathode Silver MnO2/Carbon/Silver Coating Sintered Tantalum Pellet Sponge Teflon/Epoxy Tower TYPE 597D / T97 / 13008 Cathode Termination (Silver + Ni/Sn or MnO/Carbon/ Cathode Termination Ni/SnPb Plating) Silve2r Coating (Silver + Ni/Sn/Plating) Encapsulation Encapsulation Anode Termination Epoxy Tower/ (Silver + Ni/Sn/Plating) Anode Termination Sponge Teflon (Silver + Ni/Sn or Sintered Tantalum Ni/SnPb Plating) Pellet MnO/Carbon/Silver 2 Coating Sintered Tantalum Silver Epoxy Pellet Sponge Teflon/Epoxy Tower Revision: 11-Oct-2018 2 Document Number: 40150 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Conformal Coated Guide www.vishay.com Vishay Sprague COMMERCIAL PRODUCTS SOLID TANTALUM CAPACITORS - CONFORMAL COATED SERIES 592W 592D 591D 595D 594D PRODUCT IMAGE TYPE Surface mount TANTAMOUNT™ chip, conformal coated Low profile, robust Low profile, Low profile, low ESR, Low ESR, FEATURES design for use in Maximum CV maximum CV maximum CV maximum CV pulsed applications -55 °C to +125 °C TEMPERATURE (above 40 °C, voltage -55 °C to +125 °C (above 85 °C, voltage derating is required) RANGE deratig is required) CAPACITANCE 330 μF to 2200 μF 1 μF to 2200 μF 1 μF to 1500 μF 0.1 μF to 1500 μF 1 μF to 1500 μF RANGE VOLTAGE RANGE 6 V to 10 V 4 V to 50 V 4 V to 50 V 4 V to 50 V 4 V to 50 V CAPACITANCE ± 20 % ± 10 %, ± 20 % ± 10 %, ± 20 % ± 10 %, ± 20 % ± 10 %, ± 20 % TOLERANCE LEAKAGE 0.01 CV or 0.5 μA, whichever is greater CURRENT DISSIPATION 14 % to 45 % 4 % to 50 % 4 % to 50 % 4 % to 20 % 4 % to 20 % FACTOR T, S, A, B, C, CASE CODES C, M, X S, A, B, C, D, R, M, X A, B, C, D, R, M B, C, D, R D, G, M, R TERMINATION 100 % matte tin 100 % matte tin standard, tin / lead and gold plated available SOLID TANTALUM CAPACITORS - CONFORMAL COATED SERIES 597D 572D 695D 195D 194D PRODUCT IMAGE TYPE TANTAMOUNT™ chip, conformal coated Ultra low ESR, Low profile, Pad compatible with US and European Industrial version of FEATURES maximum CV, maximum CV 194D and CWR06 case sizes CWR06 / CWR16 multi-anode TEMPERATURE -55 °C to +125 °C (above 85 °C, voltage derating is required) RANGE CAPACITANCE 10 μF to 2200 μF 2.2 μF to 220 μF 0.1 μF to 270 μF 0.1 μF to 330 μF 0.1 μF to 330 μF RANGE VOLTAGE RANGE 4 V to 75 V 4 V to 35 V 4 V to 50 V 2 V to 50 V 4 V to 50 V CAPACITANCE ± 10 %, ± 20 % TOLERANCE LEAKAGE 0.01 CV or 0.5 μA, whichever is greater CURRENT DISSIPATION 6 % to 20 % 6 % to 26 % 4 % to 8 % 4 % to 8 % 4 % to 10 % FACTOR C, S, V, X, Y, Z, R, CASE CODES V, D, E, R, F, Z, M, H P, Q, S, A, B, T A, B, D, E, F, G, H A, B, C, D, E, F, G, H A, B, D, E, F, G, H 100 % matte tin Gold plated standard; 100 % matte tin standard, tin / lead 100 % matte tin standard, tin / lead solder plated TERMINATION standard, gold plated solder plated tin / lead and gold plated available and hot solder available available dipped available Revision: 11-Oct-2018 3 Document Number: 40150 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Conformal Coated Guide www.vishay.com Vishay Sprague HIGH RELIABILITY PRODUCTS SOLID TANTALUM CAPACITORS - CONFORMAL COATED SERIES CWR06 CWR16 CWR26 13008 14002 PRODUCT IMAGE TYPE TANTAMOUNT™ chip, conformal coated MIL-PRF-55365/4 MIL-PRF-55365/13 MIL-PRF-55365/13 FEATURES DLA approved qualified qualified qualified TEMPERATURE RANGE -55 °C to +125 °C (above 85 °C, voltage derating is required) CAPACITANCE RANGE 0.10 μF to 100 μF 0.33 μF to 330 μF 10 μF to 100 μF 10 μF to 1500 μF 4.7 μF to 680 μF VOLTAGE RANGE 4 V to 50 V 4 V to 35 V 15 V to 35 V 4 V to 63 V 4 V to 50 V ± 5 %, ± 10 %, ± 5 %, ± 10 %, ± 5 %, ± 10 %, CAPACITANCE TOLERANCE ± 10 %, ± 20 % ± 10 %, ± 20 % ± 20 % ± 20 % ± 20 % LEAKAGE CURRENT 0.01 CV or 1.0 μA, whichever is greater 0.01 CV or 0.5 μA, whichever is greater DISSIPATION FACTOR 6 % to 10 % 6 % to 10 % 6 % to 12 % 6 % to 20 % 6 % to 14 % A, B, C, D, E, F, G, A, B, C, D, E, F, G, V, E, F, R, Z, D, M, CASE CODES F, G, H B, C, D, R H H H, N TERMINATION Gold plated; tin / lead; tin / lead solder fused Tin / lead SOLID TANTALUM CAPACITORS - CONFORMAL COATED SERIES T95 T96 T97 T98 PRODUCT IMAGE TYPE TANTAMOUNT™ chip, Hi-Rel COTS, conformal coated High reliability, High reliability, High reliability, FEATURES High reliability ultra low ESR, ultra low ESR, built in built in fuse multi-anode fuse, multi-anode TEMPERATURE RANGE -55 °C to +125 °C (above 85 °C, voltage derating is required) CAPACITANCE RANGE 0.15 μF to 680 μF 10 μF to 680 μF 10 μF to 2200 μF 10 μF to 1500 μF VOLTAGE RANGE 4 V to 50 V 4 V to 50 V 4 V to 75 V 4 V to 75 V CAPACITANCE TOLERANCE ± 10 %, ± 20 % ± 10 %, ± 20 % ± 10 %, ± 20 % ± 10 %, ± 20 % LEAKAGE CURRENT 0.01 CV or 0.5 μA, whichever is greater DISSIPATION FACTOR 4 % to 14 % 6 % to 14 % 6 % to 20 % 6 % to 10 % CASE CODES A, B, C, D, R, S, V, X, Y, Z R V, E, F, R, Z, D, M, H, N V, E, F, R, Z, M, H TERMINATION 100 % matte tin, tin / lead Revision: 11-Oct-2018 4 Document Number: 40150 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Conformal Coated Guide www.vishay.com Vishay Sprague TAPE AND REEL PACKAGING in inches [millimeters] 0.157 ± 0.004 (m Ta2x.) [4.0 ± 0.10] 1to0l epri atcnhcees o cnu tmapuelative Deformation 0.059 + 0.004 - 0.0 ± 0.008 [0.200] between [1.5 + 0.10 - 0.0] Embossment 0.024 embossments 0.079 ± 0.002 0.069 ± 0.004 [0.600] [2.0 ± 0.05] [1.75 ± 0.10] max. Top ctaopveer A0 0.0m30in .[0 (3.7)5] F W 20° B1 (max.) (6) K0Top B0 0.030 [0.75] Mcrooatmaxtipimoonunment cover min. (4) tape (Side or front sectional view) Center lines P For tape feeder 0.004 [0.10] of cavity 1 D1 (min.) for components reference only max. 0.079 x 0.047 [2.0 x 1.2] and l.arger (5) including draft. USER DIRECTION Concentric around B0 OF FEED Mcaavxitimy suimze (1) Cathode (-) R minimum: Anode (+) R 8 mm = 0.984" (25 mm) min. 12 mm and 16 mm = 1.181" (30 mm) DIRECTION OF FEED Bending radius (2) Tape and reel specifications: all case sizes are 3.937 [100.0] available on plastic embossed tape per EIA-481. 20° maximum Standard reel diameter is 7" (178 mm). component rotation 0.039 [1.0] max. Typical Lengthwise orientation at capacitors in tape component Tape cavity 0.039 [1.0] B0 center line max. Cathode (-) 0.9843 [250.0] Typical Camber component (Top view) A0 center line Allowable camber to be 0.039/3.937 [1/100] (Top view) Non-cumulative over 9.843 [250.0] Anode (+) DIRECTION OF FEED H-Case only Notes • Metric dimensions will govern. Dimensions in inches are rounded and for reference only. (1) A , B , K , are determined by the maximum dimensions to the ends of the terminals extending from the component body and / or the body 0 0 0 dimensions of the component. The clearance between the ends of the terminals or body of the component to the sides and depth of the cavity (A , B , K ) must be within 0.002" (0.05 mm) minimum and 0.020" (0.50 mm) maximum. The clearance allowed must also prevent 0 0 0 rotation of the component within the cavity of not more than 20°. (2) Tape with components shall pass around radius “R” without damage. The minimum trailer length may require additional length to provide “R” minimum for 12 mm embossed tape for reels with hub diameters approaching N minimum. (3) This dimension is the flat area from the edge of the sprocket hole to either outward deformation of the carrier tape between the embossed cavities or to the edge of the cavity whichever is less. (4) This dimension is the flat area from the edge of the carrier tape opposite the sprocket holes to either the outward deformation of the carrier tape between the embossed cavity or to the edge of the cavity whichever is less. (5) The embossed hole location shall be measured from the sprocket hole controlling the location of the embossement. Dimensions of embossement location shall be applied independent of each other. (6) B dimension is a reference dimension tape feeder clearance only. 1 Revision: 11-Oct-2018 5 Document Number: 40150 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Conformal Coated Guide www.vishay.com Vishay Sprague CARRIER TAPE DIMENSIONS in inches [millimeters] TAPE WIDTH W D P F E E 0 2 1 2 min. 0.315 0.14 ± 0.0019 0.246 8 mm + 0.012 / - 0.004 [3.5 ± 0.05] [6.25] [8.0 + 0.3 / - 0.1] 0.078 ± 0.0019 0.479 [2.0 ± 0.05] 0.216 ± 0.0019 0.403 12 mm [1+2 0.0.0 +12 0 /.3 - /0 -. 000.41] + 0.00.0045 9/ - 0 [5.5 ± 0.05] 0.324 ± 0.004 [10.25] [1.75 ± 0.1] 0.635 [1.5 + 0.1 / - 0] 0.295 ± 0.004 0.570 16 mm + 0.012 / - 0.004 [16.0 + 0.3 / - 0.1] 0.078 ± 0.004 [7.5 ± 0.1] [14.25] [2.0 ± 0.1] 0.945 ± 0.012 0.453 ± 0.004 0.876 24 mm [24.0 ± 0.3] [11.5 ± 0.1] [22.25] CARRIER TAPE DIMENSIONS in inches [millimeters] TAPE WIDTH TYPE CASE CODE W P K B 1 0 max. 1 max. IN mm A 8 0.157 ± 0.004 0.058 [1.47] 0.149 [3.78] B 12 [4.0 ± 0.10] 0.088 [2.23] 0.166 [4.21] C 12 0.088 [2.23] 0.290 [7.36] D 12 0.315 ± 0.004 0.088 [2.23] 0.300 [7.62] 592D M 16 [8.0 ± 0.10] 0.091 [2.30] 0.311 [7.90] 592W 591D R 12 0.088 [2.23] 0.296 [7.52] S 8 0.157 ± 0.004 0.058 [1.47] 0.139 [3.53] T 12 [4.0 ± 0.10] 0.088 [2.23] 0.166 [4.21] 0.472 ± 0.004 X 24 0.011 [2.72] 0.594 [15.1] [12.0 ± 0.10] A 8 0.157 ± 0.004 0.063 [1.60] 0.152 [3.86] B 12 [4.0 ± 0.10] 0.088 [2.23] 0.166 [4.21] C 12 0.118 [2.97] 0.290 [7.36] D 12 0.315 ± 0.004 0.119 [3.02] 0.296 [7.52] G 12 [8.0 ± 0.10] 0.111 [2.83] 0.234 [5.95] 595D H 12 0.098 [2.50] 0.232 [5.90] 594D 0.157 ± 0.004 M 12 0.085 [2.15] 0.152 [3.85] [4.0 ± 0.10] 0.315 ± 0.004 R 12 0.148 [3.78] 0.296 [7.52] [8.0 ± 0.10] S 8 0.157 ± 0.004 0.058 [1.47] 0.149 [3.78] T 8 [4.0 ± 0.10] 0.054 [1.37] 0.093 [2.36] A 8 0.058 [1.47] 0.139 [3.53] B 12 0.157 ± 0.004 0.059 [1.50] 0.189 [4.80] D 12 [4.0 ± 0.10] 0.063 [1.62] 0.191 [4.85] E 12 0.074 [1.88] 0.239 [6.07] 695D 0.315 ± 0.004 F 12 0.075 [1.93] 0.259 [6.58] [8.0 ± 0.10] 0.157 ± 0.004 G 12 0.109 [2.77] 0.301 [7.65] [4.0 ± 0.10] 0.315 ± 0.004 H 16 0.124 [3.15] 0.31 [7.87] [8.0 ± 0.10] Revision: 11-Oct-2018 6 Document Number: 40150 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Conformal Coated Guide www.vishay.com Vishay Sprague CARRIER TAPE DIMENSIONS in inches [millimeters] TAPE WIDTH TYPE CASE CODE W P K B 1 0 max. 1 max. IN mm A 8 0.058 [1.47] 0.139 [3.53] B 12 0.059 [1.50] 0.189 [4.80] 0.157 ± 0.004 C 8 0.054 [1.37] 0.093 [2.36] [4.0 ± 0.10] D 12 0.067 [1.70] 0.179 [4.55] E 12 0.074 [1.88] 0.239 [6.07] 0.315 ± 0.004 F 12 0.076 [1.93] 0.259 [6.58] [8.0 ± 0.10] 0.157 ± 0.004 G 12 0.109 [2.77] 0.301 [7.65] [4.0 ± 0.10] 195D 0.472 ± 0.004 H (1) 12 0.122 [3.11] 0.163 [4.14] [12.0 ± 0.1] 0.315 ± 0.004 R 12 0.149 [3.78] 0.296 [7.52] [8.0 ± 0.10] S 8 0.058 [1.47] 0.149 [3.78] V 8 0.060 [1.52] 0.150 [3.80] 0.157 ± 0.004 X 12 0.069 [1.75] 0.296 [7.52] [4.0 ± 0.10] Y 12 0.089 [2.26] 0.296 [7.52] Z 12 0.114 [2.89] 0.288 [7.31] A 8 0.058 [1.47] 0.149 [3.78] B 12 0.087 [2.20] 0.166 [4.21] P 8 0.043 [1.10] 0.102 [2.60] 0.157 ± 0.004 572D P 8 0.052 [1.32] 0.106 [2.70] [4.0 ± 0.10] Q 8 0.054 [1.37] 0.140 [3.55] S 8 0.058 [1.47] 0.149 [3.78] T 12 0.061 [1.55] 0.164 [4.16] A 8 0.069 [1.75] 0.139 [3.53] B 12 0.073 [1.85] 0.189 [4.80] 0.157 ± 0.004 194D C 12 [4.0 ± 0.10] 0.069 [1.75] 0.244 [6.20] CWR06 D 12 0.068 [1.72] 0.191 [4.85] CWR16 E 12 0.074 [1.88] 0.239 [6.07] CWR26 F 12 0.091 [2.31] 0.262 [6.65] 0.315 ± 0.004 G 16 0.134 [3.40] 0.289 [7.34] [8.0 ± 0.10] H 16 0.129 [3.28] 0.319 [8.10] D 16 0.317 ± 0.004 0.150 [3.80] 0.313 [7.95] E 16 [8.0 ± 0.10] 0.173 [4.40] 0.343 [8.70] F 16 0.205 [5.20] 0.309 [7.85] H 16 0.224 [5.70] 0.313 [7.95] 0.476 ± 0.004 597D M 16 0.193 [4.90] 0.339 [8.60] [12.0 ± 0.1] T97 N 16 0.283 [7.20] 0.323 [8.20] 13008 R 16 0.159 [4.05] 0.313 [7.95] 0.317 ± 0.004 V 12 0.088 [2.23] 0.300 [7.62] [8.0 ± 0.10] 0.476 ± 0.004 Z 16 0.239 [6.06] 0.311 [7.90] [12.0 ± 0.1] A 8 0.063 [1.60] 0.152 [3.86] 0.157 ± 0.004 B 12 0.088 [2.23] 0.166 [4.21] [4.0 ± 0.10] C 12 0.117 [2.97] 0.290 [7.36] D 12 0.317 ± 0.004 0.119 [3.02] 0.296 [7.52] R 12 [8.0 ± 0.10] 0.149 [3.78] 0.296 [7.52] T95 S 8 0.058 [1.47] 0.149 [3.78] V 8 0.060 [1.52] 0.150 [3.80] 0.157 ± 0.004 X 12 0.069 [1.75] 0.296 [7.52] [4.0 ± 0.10] Y 12 0.089 [2.26] 0.296 [7.52] Z 12 0.114 [2.89] 0.288 [7.31] B 12 0.157 ± 0.004 0.088 [2.23] 0.166 [4.21] C 12 [4.0 ± 0.10] 0.117 [2.97] 0.290 [7.36] 14002 D 12 0.317 ± 0.004 0.119 [3.02] 0.296 [7.52] R 12 [8.0 ± 0.10] 0.149 [3.78] 0.296 [7.52] 0.476 ± 0.004 T96 R 16 0.159 [4.05] 0.313 [7.95] [12.0 ± 0.1] F 16 0.239 [6.06] 0.311 [7.90] 0.476 ± 0.004 T98 M 16 0.193 [4.90] 0.339 [8.60] [12.0 ± 0.1] Z 16 0.272 [6.90] 0.307 [7.80] Note (1) H case only, packaging code T: lengthwise orientation at capacitors in tape. Revision: 11-Oct-2018 7 Document Number: 40150 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Conformal Coated Guide www.vishay.com Vishay Sprague PAD DIMENSIONS in inches [millimeters] B C B A CASE CODE WIDTH (A) PAD METALLIZATION (B) SEPARATION (C) 592D / W - 591D A 0.075 [1.9] 0.050 [1.3] 0.050 [1.3] B 0.118 [3.0] 0.059 [1.5] 0.059 [1.5] C 0.136 [3.5] 0.090 [2.3] 0.122 [3.1] D 0.180 [4.6] 0.090 [2.3] 0.134 [3.4] Anode pad: 0.095 [2.4] M 0.256 [6.5] 0.138 [3.5] Cathode pad: 0.067 [1.7] Anode pad: 0.095 [2.4] R 0.240 [6.1] 0.118 [3.0] Cathode pad: 0.067 [1.7] S 0.067 [1.7] 0.032 [0.8] 0.043 [1.1] X 0.310 [7.9] 0.120 [3.0] 0.360 [9.2] 595D - 594D T 0.059 [1.5] 0.028 [0.7] 0.024 [0.6] S 0.067 [1.7] 0.032 [0.8] 0.043 [1.1] A 0.083 [2.1] 0.050 [1.3] 0.050 [1.3] B 0.118 [3.0] 0.059 [1.5] 0.059 [1.5] C 0.136 [3.5] 0.090 [2.3] 0.122 [3.1] D 0.180 [4.6] 0.090 [2.3] 0.134 [3.4] G 0.156 [4.05] 0.090 [2.3] 0.082 [2.1] M 0.110 [2.8] 0.087 [2.2] 0.134 [3.4] R 0.248 [6.3] 0.090 [2.3] 0.140 [3.6] 195D A 0.067 [1.7] 0.043 [1.1] 0.028 [0.7] B 0.063 [1.6] 0.047 [1.2] 0.047 [1.2] C 0.059 [1.5] 0.031 [0.8] 0.024 [0.6] D 0.090 [2.3] 0.055 [1.4] 0.047 [1.2] E 0.090 [2.3] 0.055 [1.4] 0.079 [2.0] F 0.140 [3.6] 0.063 [1.6] 0.087 [2.2] G 0.110 [2.8] 0.059 [1.5] 0.126 [3.2] H 0.154 [3.9] 0.063 [1.6] 0.140 [3.6] N 0.244 [6.2] 0.079 [2.0] 0.118 [3.0] R 0.248 [6.3] 0.090 [2.3] 0.140 [3.6] S 0.079 [2.0] 0.039 [1.0] 0.039 [1.0] V 0.114 [2.9] 0.039 [1.0] 0.039 [1.0] X 0.118 [3.0] 0.067 [1.7] 0.122 [3.1] Y 0.118 [3.0] 0.067 [1.7] 0.122 [3.1] Z 0.118 [3.0] 0.067 [1.7] 0.122 [3.1] Revision: 11-Oct-2018 8 Document Number: 40150 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Conformal Coated Guide www.vishay.com Vishay Sprague PAD DIMENSIONS in inches [millimeters] B C B A CASE CODE WIDTH (A) PAD METALLIZATION (B) SEPARATION (C) CWR06 / CWR16 / CWR26 - 194D - 695D A 0.065 [1.6] 0.50 [1.3] 0.040 [1.0] B 0.065 [1.6] 0.70 [1.8] 0.055 [1.4] C 0.065 [1.6] 0.70 [1.8] 0.120 [3.0] D 0.115 [2.9] 0.70 [1.8] 0.070 [1.8] E 0.115 [2.9] 0.70 [1.8] 0.120 [3.0] F 0.150 [3.8] 0.70 [1.8] 0.140 [3.6] G 0.125 [3.2] 0.70 [1.8] 0.170 [4.3] H 0.165 [4.2] 0.90 [2.3] 0.170 [4.3] T95 B 0.120 [3.0] 0.059 [1.5] 0.059 [1.5] C 0.136 [3.5] 0.090 [2.3] 0.120 [3.1] D 0.180 [4.6] 0.090 [2.3] 0.136 [3.47] R 0.248 [6.3] 0.090 [2.3] 0.140 [3.6] S 0.080 [2.03] 0.040 [1.02] 0.040 [1.02] V 0.114 [2.9] 0.040 [1.02] 0.040 [1.02] X, Y, Z 0.114 [2.9] 0.065 [1.65] 0.122 [3.1] 14002 B 0.120 [3.0] 0.059 [1.5] 0.059 [1.5] C 0.136 [3.5] 0.090 [2.3] 0.120 [3.1] D 0.180 [4.6] 0.090 [2.3] 0.136 [3.47] R 0.248 [6.3] 0.090 [2.3] 0.140 [3.6] T96 R 0.248 [6.3] 0.090 [2.3] 0.140 [3.6] 597D - T97 - T98 - 13008 D, E, V 0.196 [4.9] 0.090 [2.3] 0.140 [3.6] F, R, Z 0.260 [6.6] 0.090 [2.3] 0.140 [3.6] M, H, N 0.284 [7.2] 0.090 [2.3] 0.140 [3.6] PAD DIMENSIONS in inches [millimeters] B C B 1 A CASE CODE WIDTH (A) PAD METALLIZATION (B) PAD METALLIZATION (B ) SEPARATION (C) 1 572D A 0.079 [2.0] 0.039 [1.0] 0.035 [0.9] 0.047 [1.2] Q 0.079 [2.0] 0.039 [1.0] 0.035 [0.9] 0.047 [1.2] S 0.079 [2.0] 0.039 [1.0] 0.035 [0.9] 0.047 [1.2] B 0.110 [2.8] 0.039 [1.0] 0.035 [0.9] 0.055 [1.4] P 0.055 [1.4] 0.024 [0.6] 0.024 [0.6] 0.035 [0.9] T 0.110 [2.8] 0.035 [0.9] 0.031 [0.8] 0.055 [1.4] Revision: 11-Oct-2018 9 Document Number: 40150 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Conformal Coated Guide www.vishay.com Vishay Sprague RECOMMENDED REFLOW PROFILES Capacitors should withstand reflow profile as per J-STD-020 standard, three cycles. T p T - 5 °C Max. ramp-up rate = 3 °C/s tp C Max. ramp-down rate = 6 °C/s C) T RE (° L Ts max. Preheat area tL U T A R T E s min. P M TE ts 25 Time 25 °C to peak TIME (s) PROFILE FEATURE SnPb EUTECTIC ASSEMBLY LEAD (Pb)-FREE ASSEMBLY Preheat / soak Temperature min. (T ) 100 °C 150 °C s min. Temperature max. (T ) 150 °C 200 °C s max. Time (t) from (T to T ) 60 s to 120 s 60 s to 120 s s smin. s max. Ramp-up Ramp-up rate (T to T ) 3 °C/s max. 3 °C/s max. L p Liquidus temperature (T ) 183 °C 217 °C L Time (t ) maintained above T 60 s to 150 s 60 s to 150 s L L Peak package body temperature (T ) Depends on type and case – see table below p Time (tp)* within 5 °C of the specified 20 s 30 s classification temperature (T ) c Ramp-down Ramp-down rate (T to T ) 6 °C/s max. 6 °C/s max. p L Time 25 °C to peak temperature 6 min max. 8 min max. PEAK PACKAGE BODY TEMPERATURE (T ) p PEAK PACKAGE BODY TEMPERATURE (T ) p TYPE / CASE CODE SnPb EUTECTIC PROCESS LEAD (Pb)-FREE PROCESS 591D / 592D - all cases, except X25H, M and R cases 235 °C 260 °C 591D / 592D - X25H, M and R cases 220 °C 250 °C 594D / 595D - all cases except C, D, and R 235 °C 260 °C 594D / 595D - C, D, and R case 220 °C 250 °C 572D all cases n/a 260 °C T95 A, B, S, V, X, Y cases 235 °C 260 °C T95 C, D, R, and Z cases 220 °C 250 °C 14002 B case 235 °C n/a 14002 C, D, and R cases 220 °C n/a T96 R case 220 °C 250 °C 195D all cases, except G, H, R, and Z 235 °C 260 °C 195D G, H, R, and Z cases 220 °C 250 °C 695D all cases, except G and H cases 235 °C 260 °C 695D G, H cases 220 °C 250 °C 597D, T97, T98 all cases, except V case 220 °C 250 °C 597D, T97, T98 V case 235 °C 260 °C 194D all cases, except H and G cases 235 °C 260 °C 194D H and G cases 220 °C 250 °C Revision: 11-Oct-2018 10 Document Number: 40150 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Conformal Coated Guide www.vishay.com Vishay Sprague GUIDE TO APPLICATION 1. AC Ripple Current: the maximum allowable ripple 5. Power Dissipation: power dissipation will be current shall be determined from the formula: affected by the heat sinking capability of the mounting surface. Non-sinusoidal ripple current may P I = ------------ produce heating effects which differ from those RMS RESR shown. It is important that the equivalent IRMS value be established when calculating permissible where, operating levels. (Power dissipation calculated using P = power dissipation in W at +25 °C as given in derating factor (see paragraph 4)). the tables in the product datasheets (Power Dissipation). 6. Attachment: RESR = the capacitor equivalent series resistance at 6.1 Soldering: capacitors can be attached by the specified frequency conventional soldering techniques, convection, infrared reflow, wave soldering and hot plate 2. AC Ripple Voltage: the maximum allowable ripple methods. The soldering profile chart shows typical voltage shall be determined from the formula: recommended time / temperature conditions for V = I x Z soldering. Preheating is recommended to reduce RMS RMS thermal stress. The recommended maximum preheat or, from the formula: rate is 2 °C/s. Attachment with a soldering iron is not P recommended due to the difficulty of controlling V = Z ------------ RMS R temperature and time at temperature. The soldering ESR iron must never come in contact with the capacitor. where, 7. Recommended Mounting Pad Geometries: the nib P = power dissipation in W at +25 °C as given in must have sufficient clearance to avoid electrical the tables in the product datasheets (Power contact with other components. The width Dissipation). dimension indicated is the same as the maximum width of the capacitor. This is to minimize lateral R = the capacitor equivalent series resistance at ESR movement. the specified frequency Z = the capacitor impedance at the specified 8. Cleaning (Flux Removal) After Soldering: frequency TANTAMOUNT™ capacitors are compatible with all commonly used solvents such as TES, TMS, Prelete, 2.1 The sum of the peak AC voltage plus the applied DC Chlorethane, Terpene and aqueous cleaning media. voltage shall not exceed the DC voltage rating of the However, CFC / ODS products are not used in the capacitor. production of these devices and are not recommended. Solvents containing methylene 2.2 The sum of the negative peak AC voltage plus chloride or other epoxy solvents should be avoided the applied DC voltage shall not allow a voltage since these will attack the epoxy encapsulation reversal exceeding 10 % of the DC working voltage material. at +25 °C. 3. Reverse Voltage: solid tantalum capacitors are not intended for use with reverse voltage applied. However, they have been shown to be capable of withstanding momentary reverse voltage peaks of up to 10 % of the DC rating at 25 °C and 5 % of the DC rating at +85 °C. 4. Temperature Derating: if these capacitors are to be operated at temperatures above +25 °C, the permissible RMS ripple current shall be calculated using the derating factors as shown: TEMPERATURE DERATING FACTOR +25 °C 1.0 +85 °C 0.9 +125 °C 0.4 Revision: 11-Oct-2018 11 Document Number: 40150 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Typical Performance Characteristics www.vishay.com Vishay Sprague COTS Tantalum Capacitors ELECTRICAL PERFORMANCE CHARACTERISTICS ITEM PERFORMANCE CHARACTERISTICS Category temperature range -55 °C to +85 °C (to +125 °C with voltage derating) Capacitance tolerance ± 20 %, ± 10 %, tested via bridge method, at 25 °C, 120 Hz Dissipation factor Limit per Standard Ratings table. Tested via bridge method, at 25 °C, 120 Hz ESR Limit per Standard Ratings table. Tested via bridge method, at 25 °C, 100 kHz Leakage current After application of rated voltage applied to capacitors for 5 min using a steady source of power with 1 k resistor in series with the capacitor under test, leakage current at 25 °C is not more than 0.01 CV or 0.5 μA, whichever is greater. Note that the leakage current varies with temperature and applied voltage . See graph below for the appropriate adjustment factor. Capacitance change by +15 % max. (at +125 °C) temperature +10 % max. (at +85 °C) -10 % max. (at -55 °C) Reverse voltage Capacitors are capable of withstanding peak voltages in the reverse direction equal to: 10 % of the DC rating at +25 °C 5 % of the DC rating at +85 °C 1 % of the DC rating at +125 °C Vishay does not recommend intentional or repetitive application of reverse voltage. Ripple current For maximum ripple current values (at 25 °C) refer to relevant datasheet. If capacitors are to be used a t temperatures above +25 °C, the permissible RMS ripple current (or voltage) shall be calculated using the derating factors: 1.0 at +25 °C 0.9 at +85 °C 0.4 at +125 °C Maximum operating and surge +85 °C +125 °C voltages vs. temperature RATED VOLTAGE SURGE VOLTAGE CATEGORY VOLTAGE SURGE VOLTAGE (V) (V) (V) (V) 4.0 5.2 2.7 3.4 6.3 8.0 4.0 5.0 10 13 7.0 8.0 16 20 10 12 20 26 13 16 25 32 17 20 35 46 23 28 40 52 26 31 50 65 33 40 50 (1) 60 33 40 63 75 42 50 75 75 50 50 Recommended voltage VOLTAGE RAIL CAPACITOR VOLTAGE RATING derating guidelines  3.3 6.3 (below 85 °C) (2) 5 10 10 20 12 25 15 35  24 50 or series configuration Notes • All information presented in this document reflects typical performance characteristics (1) Capacitance value 15 μF and higher (2) For temperatures above +85 °C the same voltage derating ratio is recommended, but with respect to category voltage: up to +85 °C: category voltage = rated voltage; at +125 °C: category voltage = 2/3 of rated voltage, between these temperatures it decreases linearly - see graph below Revision: 07-Feb-2019 1 Document Number: 40209 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Typical Performance Characteristics www.vishay.com Vishay Sprague CATEGORY VOLTAGE VS. TEMPERATURE Axis Title 1.2 10000 1.0 V) e ( 0.8 1000 g 2nd lineory Volta 0.6 1st line2nd line g e 0.4 100 at C 0.2 0 10 -55 0 25 55 85 105 125 Temperature (°C) TYPICAL LEAKAGE CURRENT TEMPERATURE FACTOR Axis Title 100 10000 10 or act 1000 F 2nd linee Current 0.11 ++18255 ° C°C 1st line2ndline g +55 °C a 100 k a Le 0.01 +25 °C 0 °C -55 °C 0.001 10 0 10 20 30 40 50 60 70 80 90 100 Percent of Rated Voltage Notes • At +25 °C, the leakage current shall not exceed the value listed in the Standard Ratings table. • At +85 °C, the leakage current shall not exceed 10 times the value listed in the Standard Ratings table. • At +125 °C, the leakage current shall not exceed 12 times the value listed in the Standard Ratings table Revision: 07-Feb-2019 2 Document Number: 40209 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Typical Performance Characteristics www.vishay.com Vishay Sprague ENVIRONMENTAL PERFORMANCE CHARACTERISTICS ITEM CONDITION POST TEST PERFORMANCE Surge voltage MIL-PRF-55365 Capacitance change Within ± 10 % of initial value 1000 successive test cycles at 85 °C of surge Dissipation factor Initial specified limit voltage (as specified in the table above), in Leakage current Initial specified limit series with a 33  resistor at the rate of 30 s ON, 30 s OFF Life test at +85 °C MIL-STD-202, method 108 Capacitance change Within ± 10 % of initial value 1000 h application of rated voltage at 85 °C Dissipation factor Initial specified limit Leakage current Shall not exceed 125 % of initial limit Life test at +125 °C MIL-STD-202, method 108 Capacitance change Within ± 10 % of initial value 1000 h application 2/3 of rated voltage at 125 °C Dissipation factor Initial specified limit Leakage current Shall not exceed 125 % of initial limit Moisture resistance MIL-STD-202, method 106 at rated voltage, Capacitance change Within ± 15 % of initial value 20 cycles Dissipation factor Shall not exceed 150 % of initial limit Leakage current Shall not exceed 200 % of initial limit Stability at low and MIL-PRF-55365 Delta cap limit at -55 °C, 85 °C is ± 10 % of initial value high temperatures Delta cap limit at 125 °C is ± 15 % of initial value Delta cap at step 3 and final step 25 °C is ± 10 % DCL at 85 °C: 10 x initial specified value DCL at 125 °C: 12 x initial specified value DCL at 25 °C: initial specified value at RV Thermal shock MIL-STD-202, method 107 Capacitance change Within ± 10 % of initial value At -55 °C / +125 °C, for 5 cycles, Dissipation factor Initial specified limit 30 min at each temperature Leakage current Initial specified limit MECHANICAL PERFORMANCE CHARACTERISTICS ITEM CONDITION POST TEST PERFORMANCE Terminal strength / Apply a pressure load of 5 N for 10 s ± 1 s Capacitance change Within ± 10 % of initial value Shear force test horizontally to the center of capacitor side body Dissipation factor Initial specified limit Leakage current Initial specified limit There shall be no mechanical or visual damage to capacitors post-conditioning. Vibration MIL-STD-202, method 204, condition D, Electrical measurements are not applicable, since the same 10 Hz to 2000 Hz, 20 g peak, 8 h, at rated voltage parts are used for shock (specified pulse) test. There shall be no mechanical or visual damage to capacitors post-conditioning. Shock MIL-STD-202, method 213, condition I, Capacitance change Within ± 10 % of initial value (specified pulse) 100 g peak Dissipation factor Initial specified limit Leakage current Initial specified limit There shall be no mechanical or visual damage to capacitors post-conditioning. Resistance MIL-STD-202, method 210, condition J Capacitance change Within ± 10 % of initial value to soldering heat (leadbearing capacitors) and K (lead (Pb)-free Dissipation factor Initial specified limit capacitors), one heat cycle Leakage current Initial specified limit Solderability MIL-STD-202, method 208, ANSI/J-STD-002, Solder coating of all capacitors shall meet specified test B (leadbearing) and B1 (lead (Pb)-free). requirements. Preconditioning per category C (category E - There shall be no mechanical or visual damage to capacitors optional). post-conditioning. Does not apply to gold terminations. Lead (Pb)-free and leadbearing capacitors are backward and forward compatible Resistance to MIL-STD-202, method 215 There shall be no mechanical or visual damage to capacitors solvents post-conditioning. Body marking shall remain legible. Flammability Encapsulation materials meet UL 94 V-0 with an oxygen index of 32 % Revision: 07-Feb-2019 3 Document Number: 40209 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Legal Disclaimer Notice www.vishay.com Vishay Disclaimer  ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2017 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 08-Feb-17 1 Document Number: 91000