General Purpose High Power PCB Relays PPootttteerr && BBrruummfifieelldd T92 Series Two-pole 30A PCB or Panel Mount Relay n 40A, 2 form A (NO) and 2 form C (CO) switching capability n Designed to control compressor loads to 3.5 tons, 110LRA / 25.3FLA n Meets requirements of UL 508 and UL 873 spacings - 8mm through air, 9.5mm over surface n Meets requirements of VDE 8mm spacing, 4kV dielectric coil-to- contact n Meets requirements of UL Class F construction n UL approved for 600VAC switching (1.5HP) n Screw terminal version (consult factory for availability, ratings) n Anti-explosive version available (Meets EN 60079-15) n WG version available (Meets EN 60335-1) Typical applications HVAC, residential / commercial appliances, industrial controls. Approvals Contact ratings 1) (continued) UL E22575 (Recognized and Listed); CSA LR48471; VDE 40019600 AgCdO, PC mount relays Technical data of approved types on request. NO 30A, 400VAC 100x103 NC 3A, 400VAC 30x103 Contact Data CO 30A NO / 3A NC, 400VAC 30x103 Contact arrangement 2 form A (NO), 2 form C (CO) Anti-explosion, sealed type Rated voltage 277VAC NO 30A 250VAC, 25°C 100x103 Max. switching voltage 600VAC Anti-explosion, break device Rated current 30A NO; 3A NC NO 15A 480VAC 100x103 Limiting continuous current 40A NO; 3A NC ARI 780-86 Endurance Test (section 6.6): Limiting making current 40A NO; 3A NC HVAC Definite Purpose Contactor Standard Limiting breaking current 40A NO; 3A NC Normally Open Contacts Contact material AgSnOInO, AgCdO Single Phase/Two Pole (Both poles together switching a single load) Min. recommended contact load 500ma (NO)/ 100ma (NC), 12VAC 110 LRA, 25.3 FLA, 200K operations (DC Coil) Frequency of operation, with load 360hr L1 L2 Operate/release time max., including bounce 25/25ms Initial contact resistance < 100 mΩ at 6VDC 1A Figure 1 T1 T2 Contact ratings 1) Single Phase Per Pole (Single load per pole) Type Load Cycles 110 LRA, 18 FLA, 200K operations (DC Coil). UL508 60 LRA, 14 FLA, 200K operations (AC Coil). AgCdO L1 L2 NO 40A, 277VAC, resistive 6x103 NO 30A, 120/277VAC, resistive 100x103 Figure 2 T1 T2 NO 10A, 600VAC, general purpose 100x103 NO 1HP, 120VAC 100x103 NO 3HP, 240VAC 1x103 1) Contact ratings at 25°C (unless otherwise noted) with relay properly vented. NO 1.5HP, 480 or 600VAC 100x103 FLA, LRA ratings are compatible with 3.5 ton compressor applications. NO 110LRA/25.3FLA, 240VAC (DC coil only) 100x103 NO 60LRA/14FLA, 240VAC (AC coil only) 100x103 Mechanical endurance 10x106 ops. NO 3A, 240VAC, pilot duty 100x103 NO 20A, 28VDC, resistive 100x103 NO TV10, 120VAC 100x103 Coil Data NC 3A, 277VAC 100x103 Coil voltage range 5 to 110VDC; 12 to 240VAC NC 2A, 480VAC 100x103 Max. coil power 1.7W; 4.0VA NC 1A, 600VAC 100x103 Max. coil temperature 155°C AgSnOInO Coil insulation system according UL Class F NO 40A, 240VAC, resistive 85°C 50x103 Coil versions, DC coil (D type) NO 30A, 120/277VAC, resistive (DC coil only) 200x103 Coil Rated Operate Release Coil Rated coil NO 30A, 120/277VAC, resistive (AC coil only) 100x103 code voltage voltage voltage resistance power NO 20A, 480VAC, resistive 100x103 VDC VDC VDC Ω±10% W NO 1.5HP, 120VAC, 2 pole making/breaking (Fig.1) 100x103 5 5 3.75 0.6 14.9 1.7 NO 3HP, 240VAC, 3 phase (DC coil only) 100x103 6 6 4.5 0.6 22 1.7 NO 3HP, 480VAC, 3 phase (DC coil only) 100x103 9 9 6.75 0.9 48 1.7 NO 2HP, 600VAC, 3 phase (DC coil only) 100x103 12 12 9 1.2 86 1.7 VDE 18 18 13.5 1.8 197 1.7 AgCdO, flange mount relays 22 22 16.5 2.2 294 1.7 NO 20A, 400VAC 100x103 24 24 18 2.4 350 1.7 NC 3A, 400VAC 30x103 36 36 27 3.6 767 1.7 CO 20A NO / 3A NC, 400VAC 30x103 48 48 36 4.8 1390 1.7 110 110 82.5 11 7255 1.7 120 120 90 12 8514 1.7 1 04-2019, Rev. 0419 Catalog and product specification according Catalog and product data is subject to the Catalog product data, ‘Definitions’ section, www.te.com to IEC 61810-1 and to be used only together terms of the disclaimer and all chapters of application notes and all specifications are © 2012 Tyco Electronics Corporation, with the ‘Definitions’ section. the ‘Definitions’ section, available at subject to change. a TE Connectivity Ltd. company. http://relays.te.com/definitions

General Purpose High Power PCB Relays PPootttteerr && BBrruummfifieelldd T92 Series Two-pole 30A PCB or Panel Mount Relay (Continued) Coil versions, AC coil (A type) (continued) Insulation Data Coil Rated Frequency Operate Release Coil Rated coil Initial dielectric strength code voltage voltage voltage resistance power between open contacts 1500Vrms VAC Hz VAC, 60Hz VAC, 60Hz Ω±10% VA between contact and coil 4000Vrms 12 12 60 9.6 1.2 9.1 4 between adjacent contact 2000Vrms 24 24 60 19.2 2.4 36.6 4 Initial surge withstand voltage 110 110 60 88 11 793 4 between contact and coil 8kV 120 110/120 50/60 96 12 950 4 Initial insulation resistance 208 208 60 166.4 20.8 2841 4 between insulated elements 1x109Ω 240 220/240 50/60 192 24 3800 4 Clearance/creepage 277 250/277 50/60 221.6 27.7 5485 4 between contact and coil 8mm clearance/9.5mm creepage Coil versions, AC coil (F type) Coil Rated Frequency Operate Release Coil Rated coil code voltage voltage voltage resistance power Other Data VAC Hz VAC, 60Hz VAC, 60Hz Ω±10% VA Material compliance: EU RoHS/ELV, China RoHS, REACH, Halogen content 12 12 50 9.6 1.2 11.2 3.5 refer to the Product Compliance Support Center at 24 24 50 19.2 2.4 44.4 3.5 www.te.com/customersupport/rohssupportcenter 48 48 50 38.4 4.8 179.2 3.5 Ambient temperature 240 240 50 192 24 4355 3.5 DC coil -55ºC to 85ºC All figures are given for coil without preenergization, at ambient temperature +23°C. For A AC coil -55ºC to 65ºC type, 110V/120V, 50/60Hz. Signify 50Hz Operation at Nominal 110V, 60 Hz Operation at Category of environmental protection Nominal 120V. IEC 61810 RTI - dust protected, Coil Data (continued) RTII - flux proof, RTIII - wash tight Ambient temperature vs. coil voltage Vibration resistance (functional) 1.65mm max excursions, 10-55 Hz Assumptions: Shock resistance (functional) 10g for 11msec 1. Thermal resistance = 35°C per Watt (DC only.) Shock resistance (destructive) 100g 2. Still air. Terminal type PCB-tht or quick connect 3. Nominal coil resistance. Weight 86g 4. Max. mean coil temperature = 155°C (change of resistance method). Resistance to soldering heat THT 5. Coil temperature rise due to load = 6.3°C @ 30 amps. IEC 60068-2-20 260°C 6. Curves are based on 1.7W at 25°C (DC only.) Packaging/unit tray/30 pcs., box/120 pcs. C) 120 e Ambient Temp. (°1860000 A CAC C Coiol i3l 00 AA D DCC C Coiol i3l 00 AAmmpp CCoonnttaacctt LLooaadd bl 40 a w Allo 20 x. a 0 M 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140145 150 Applied Coil Voltage (% of Rated Nominal) Dimensions T92 – Mounting and termination code 1 T92 – Mounting and termination code 2, 3 and 4 . 2 . ( 05 62 .M 3 2A ) X . 1 . (3 3 64 .M 5 4A ) X . 2.7(6080. 5M8A)X. 1.(3364 .M54A)X. 1.21 MAX. 1.04 MAX. 1.495 MAX. (30.73) .156 (26.42) (37.97) (3.96) .250 TYP. 1.618 ± .020 (6.35) .585 ± .005 (41.10 ± .51) .047 TYP. 2.05 MAX. (14.86 ± .13) .(370.895 ± ± . 0.1035) .03(02. 8T1Y)P. (1.19) 2(5.394.556 ± ± . 0.1035) (52.07) 1.618 TYP. (41.10 ± .51) .585 ± .005 (14.86 ± .13) .309 ± .005 1.000 ± .010 .630 ± .005 (7.85 ± .13) (16.00 ± .13) (25.40 ± .25) .090 RAD. (2.29) FOR #8 SCREW .630 TYP. (16.00) 2 04-2019, Rev. 0419 Catalog and product specification according Catalog and product data is subject to the Catalog product data, ‘Definitions’ section, www.te.com to IEC 61810-1 and to be used only together terms of the disclaimer and all chapters of application notes and all specifications are © 2012 Tyco Electronics Corporation, with the ‘Definitions’ section. the ‘Definitions’ section, available at subject to change. a TE Connectivity Ltd. company. http://relays.te.com/definitions

General Purpose High Power PCB Relays PPootttteerr && BBrruummfifieelldd T92 Series Two-pole 30A PCB or Panel Mount Relay (Continued) Dimensions Terminal assignment Bottom view on pins T92 – Mounting and termination code 5 2 form A 2 form C 2.700 MAX. (68.58) 0 0 1.36 MAX. (34.54) 2 4 2 4 3 .090 (2.29) RAD. FOR 6 8 6 8 7 #8 SCREW 1 1 2.345 ± .005 (59.56 ± .13) 2.135 MAX. 1.431 MAX. (54.23) (36.34) PCB layout Bottom view on pins T92 - Mounting and termination code 1 2.010 MAX. (51.05) 1.618 (41.10) .585 .9(1233 .M19A)X. .309 (14.86) .185 (7.85) (4.70) .365 (9.27) .630 1.000 (16.00) (25.40) .203 TYP. (5.16) .052 TYP. .072 TYP. (1.32) .162 (1.83) (4.12) An alternate PC board layout utilizes .076 ± .003 (1.93 ± .076) diameter holes on the same center-to-center spacing shown above. Use of the rectangular holes is recommended for improved solderability. Only necessary terminals are present on single throw models. Consequently, some holes will be unnecessary for single throw models. Product code structure Typical product code T92 S 11 D 2 2 -24 -99 Type T92 Printed circuit board / panel mount power relay T92 Enclosure P Dust protected plastic case S Wash-tight, tape sealed, plastic case (Mounting and termination code 1) Top sealed, not wash-tight, not tape sealed on bottom (Mounting and termination codes 2, 3 & 4) Contact arrangement 7 2 form A (2 NO) 11 2 form C (2 CO) Coil Input A AC voltage, 60Hz or 50/60 Hz (consult coil versions table) D DC voltage F AC voltage, 50Hz Mounting and termination 1 Printed circuit board mount; printed circuit board terminals. 2 Panel mount via flanged cover; .250” (6.35mm) x .032” (.81mm) QC terminal 3 Panel mount via flanged cover; .187” (4.75mm) x .032” (.81mm) QC terminals for coil and .250” (6.35mm) for contacts 4 Panel mount via flanged cover, .187” (4.75mm) x .020” (.51mm) QC terminals for coil and .250” (6.35mm) for contacts. 5 Panel mount via flanged cover, M4 screws w/ captive pressure plates. Requires Enclosure P and Contact arrangement 7. Contact material 2 AgCdO 4 AgSnOInO X AgSnO+AgNi Coil voltage Coil code: please refer to coil versions table Customer code -99 Anti-explosion 3 04-2019, Rev. 0419 Catalog and product specification according Catalog and product data is subject to the Catalog product data, ‘Definitions’ section, www.te.com to IEC 61810-1 and to be used only together terms of the disclaimer and all chapters of application notes and all specifications are © 2012 Tyco Electronics Corporation, with the ‘Definitions’ section. the ‘Definitions’ section, available at subject to change. a TE Connectivity Ltd. company. http://relays.te.com/definitions

General Purpose High Power PCB Relays PPootttteerr && BBrruummfifieelldd T92 Series Two-pole 30A PCB or Panel Mount Relay (Continued) Product Code Enclosure Contacts Coil Mounting Contact Material Coil Part Number  T92P7A22-24 Plastic dust cover 2 form A, 2 NO AC Panel mount + quick connect AgCdO 24 VAC 6-1393211-0   T92P7A22-120 120 VAC 5-1393211-7   T92P7A22-240 240 VAC 6-1393211-2   T92P7A22-277 277 VAC 6-1393211-3   T92P7A24-240 AgSnOInO 240 VAC 3-1423008-3   T92P7A52-120 Panel mount + screw terminals AgCdO 120 VAC 1423008-8   T92P7A52-240 240 VAC 1-1423008-2   T92P7D12-12 DC PCB terminals 12 VDC 6-1393211-5   T92P7D12-24 24 VDC 6-1393211-6   T92P7D22-12 Panel mount + quick connect 12VDC 6-1393211-9   T92P7D22-24 24 VDC 7-1393211-1   T92P7D22-48 48 VDC 7-1393211-2   T92P7D24-12 AgSnOInO 12VDC 2-1423008-2   T92P7D24-24 24 VDC 1423008-9   T92P7D42-24 AgCdO 7-1393211-5   T92P7D52-12 Panel mount + screw terminals 12 VDC 1-1423008-0   T92P7D52-24 24 VDC 1423967-1   T92P11A12-120 2 form C, 2 CO AC PCB terminals 120 VAC 3-1393211-8   T92P11A22-12 Panel mount + quick connect 12 VAC 3-1393211-9   T92P11A22-24 24 VAC 4-1393211-3   T92P11A22-120 120 VAC 4-1393211-0   T92P11A22-240 240 VAC 4-1393211-4   T92P11A22-277 277 VAC 4-1393211-6   T92P11A24-240 AgSnOInO 240 VAC 3-1423008-7   T92P11A42-120 AgCdO 120VAC 4-1393211-8   T92P11D12-12 DC PCB terminals 12 VDC 5-1393211-0   T92P11D22-12 Panel mount + quick connect 5-1393211-3   T92P11D22-24 24 VDC 5-1393211-4   T92P11D24-12 AgSnOInO 12 VDC 3-1423008-5   T92P11D24-24 24 VDC 3-1423008-6   T92S7A12-24 Wash tight 2 form A, 2 NO AC PCB terminals AgCdO 24 VAC 9-1393211-8   T92S7A12-120 120 VAC 9-1393211-7   T92S7A12-240 240 VAC 9-1393211-9   T92S7A22-24 Top sealed Panel mount + quick connect 24 VAC 1393212-4   T92S7A22-120 120 VAC 1393212-2   T92S7A22-240 240 VAC 1393212-5   T92S7D12-12 Wash tight DC PCB terminals 12 VDC 1393212-8   T92S7D12-24 24 VDC 1-1393212-0   T92S7D12-48 48 VDC 1-1393212-1   T92S7D12-110 110 VDC 1393212-7   T92S7D14-24 AgSnOInO 24 VDC 1-1423008-8   T92S7D22-12 Top sealed Panel mount + quick connect AgCdO 12 VDC 1-1393212-4   T92S7D22-18 18 VDC 1-1393212-5   T92S7D22-24 24 VDC 1-1393212-7   T92S7D22-110 110 VDC 1-1393212-3   T92S11A12-24 Wash tight 2 form C, 2 CO AC PCB terminals 24 VAC 8-1393211-1   T92S11A12-120 120 VAC 8-1393211-0   T92S11A12-240 240 VAC 8-1393211-2   T92S11A22-12 Top sealed Panel mount + quick connect 12 VAC 8-1393211-3   T92S11A22-24 24 VAC 8-1393211-6   T92S11A22-120 120 VAC 8-1393211-4   T92S11A22-240 240 VAC 8-1393211-7   T92S11D12-12 Wash tight DC PCB terminals 12 VDC 8-1393211-9   T92S11D12-24 24 VDC 9-1393211-0   T92S11D12-48 48 VDC 9-1393211-1   T92S11D12-110 110 VDC 8-1393211-8   T92S11D22-12 Top sealed Panel mount + quick connect 12 VDC 9-1393211-3   T92S11D22-24 24 VDC 9-1393211-4  T92P7D12-12-99 Plastic dust cover 2 form A, 2 NO DC PCB terminals AgCdO 12VDC 2-2071223-3 T92S7D1X-12-99 Wash tight AgSnO+AgNi 12VDC 6-1423008-1 T92S7D2X-12-99 Top Sealed Panel mount + quick connect 12VDC 6-1423008-2 T92S7A22-240 Top Sealed(WG) AC AgCdO 240VAC 1393212-5 T92S7D12-12-00 Wash tight (WG) DC PCB terminals 12VDC 1-2071223-7 T92S7D22-12-02 Top Sealed(WG) Panel mount + quick connect 12VDC 1-2071223-5 4 04-2019, Rev. 0419 Catalog and product specification according Catalog and product data is subject to the Catalog product data, ‘Definitions’ section, www.te.com to IEC 61810-1 and to be used only together terms of the disclaimer and all chapters of application notes and all specifications are © 2012 Tyco Electronics Corporation, with the ‘Definitions’ section. the ‘Definitions’ section, available at subject to change. a TE Connectivity Ltd. company. http://relays.te.com/definitions