ST www.vishay.com Vishay SuperTan® Wet Tantalum Capacitors with Hermetic Seal FEATURES • Very high capacitance • 10 μF to 1800 μF • 25 VDC to 125 VDC Available • Very low ESR Available • High ripple current • All tantalum case • Hermetically sealed • Low DCL • Axial through-hole terminations: standard tin / lead (Sn / Pb), 100 % tin (RoHS-compliant) available • Material categorization: for definitions of compliance Vishay ST represents a major breakthrough in wet tantalum please see www.vishay.com/doc?99912 capacitor technology. Its unique cathode system provides Note the highest capacitance per unit volume. The design * This datasheet provides information about parts that are facilitates a doubling of capacitance, lower ESR and higher RoHS-compliant and / or parts that are non RoHS-compliant. For ripple current rating compared with conventional wet example, parts with lead (Pb) terminations are not RoHS-compliant. tantalum products. Moreover, the ST has the capacitance Please see the information / tables in this datasheet for details stability of a solid tantalum capacitor and there are no circuit APPLICATION NOTES impedance restrictions. a. No continuous reverse voltage permissible. The ST is housed in an all tantalum, hermetically sealed case and is manufactured to withstand hazardous environments. b. The peak of the applied AC ripple and the applied DC voltage must not exceed the DC voltage rating of the The ST is used widely in the defense and aerospace capacitor. industries and whenever there is a space problem. c. Ripple current ratings by part number at 85 °C and PERFORMANCE CHARACTERISTICS 40 kHz are included in the table. Ripple current correction factors for other temperatures and frequencies are given Operating Temperature: -55 °C to +85 °C on the next page. (to +125 °C with voltage derating) d. Transient reverse voltage surges are acceptable under Capacitance Tolerance: at 120 Hz, +25 °C. the following conditions: ± 20 % standard. ± 10 % available as special. the peak reverse voltage does not exceed 1.5 V and the peak current times the duration of the reverse transient does not exceed 0.05 As. In addition, the repetition frequency of the reverse voltage surge is less than 10 Hz. DIMENSIONS in inches [millimeters] Terminal welded 0.0253 ± 0.002 [0.64 ± 0.05] dia. to case 0.250 [6.35] (no. 22 AWG) tinned nickel leads MAX. solderable and weldable 0.094 [2.38] MAX. Terminal location “D” DIA. E L1 E within 0.031 of center MAX. INSULATED L + 0.031 / - 0.016 [+ 0.79 / - 0.41] CASE CODE D ± 0.016 [0.41] 1 E ± 0.250 [6.3] MAX. (DIA.) UNINSULATED T1 0.188 [4.78] 0.219 [5.56] 0.453 [11.51] 1.500 [38.10] T2 0.281 [7.14] 0.312 [7.92] 0.641 [16.28] 2.250 [57.15] L2 0.281 [7.14] 0.312 [7.92] 1.008 [25.60] 2.250 [57.15] T3 0.375 [9.52] 0.406 [10.31] 0.766 [19.46] 2.250 [57.15] T4 0.375 [9.52] 0.406 [10.31] 1.062 [26.97] 2.250 [57.15] Notes • Material at egress is Tantalum • Approx. weight: • Insulation sleeving will lap over the ends of the capacitor case T1: 2.3 g, T2: 5.7 g, T3: 9.4 g, T4: 14.8 g Revision: 25-Jun-2018 1 Document Number: 43000 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

ST www.vishay.com Vishay  ORDERING INFORMATION ST 220 100 T4 M I E3 Super Tan® CAPACITANCE 85 °C RATED CASE CODE CAPACITANCE INSULATING RoHS-compliant COMMERCIAL μF DC VOLTAGE TOLERANCE SLEEVE CAP. TYPE M = ± 20 % I = insulated E3 = 100 % tin termination K = ± 10 % X = uninsulated (RoHS compliant) Blank = SnPb termination (standard design) STANDARD RATINGS CAPACITANCE MAX. MAX. DCL AT MAX. IMP. MAXC. CHAAPNAGCEI TAATNCE AC8 R5I P°CPLE AT 25 °C CASE ESR AT -55 °C AND( μ1F2)0 Hz CODE 12(0 H) z +2(μ5A °)C ++81(52μ 5A° C)°C / AND( 12)0 Hz -5(%5 °)C +8(%5 °)C +1(2%5) °C 4R(0m MkAHS)z PART NUMBER 25 V AT 85 °C; 15 V AT 125 °C DC DC 120 T1 1.3 1 5 25 -42 +8 +12 1250 ST120-25T1MI 560 T2 0.83 2 10 12 -65 +10 +15 2100 ST560-25T2MI 1100 L2 0.5 3 25 7 -60 +20 +45 3200 ST1100-25L2MI 1200 T3 0.65 5 20 7 -70 +12 +18 2600 ST1200-25T3MI 1800 T4 0.5 6 25 7 -72 +12 +20 3100 ST1800-25T4MI 30 V AT 85 °C; 20 V AT 125 °C DC DC 100 T1 1.3 1 5 25 -38 +8 +12 1200 ST100-30TMI 470 T2 0.85 2 10 15 -65 +10 +18 1800 ST470-30T2MI 950 L2 0.5 5 30 7 -55 +18 +35 3200 ST950-30L2MI 1000 T3 0.7 7 25 7 -70 +10 +18 2500 ST1000-30T3MI 1500 T4 0.6 12 35 6 -72 +10 +20 3000 ST1500-30T4MI 50 V AT 85 °C; 30 V AT 125 °C DC DC 68 T1 1.5 1 5 35 -25 +8 +15 1050 ST68-50T1MI 220 T2 0.9 2 10 17.5 -50 +8 +15 1800 ST220-50T2MI 450 L2 0.6 3 25 7.5 -45 +12 +30 2900 ST450-50L2MI 470 T3 0.75 3 25 10 -45 +8 +15 2100 ST470-50T3MI 680 T4 0.7 5 40 8 -58 +10 +20 2750 ST680-50T4MI 60 V AT 85 °C; 40 V AT 125 °C DC DC 47 T1 2.0 1 5 44 -25 +8 +12 1050 ST47-60T1MI 150 T2 1.1 2 10 20 -40 +8 +15 1800 ST150-60T2MI 370 L2 0.6 3 25 9 -33 +9 +20 2900 ST370-60L2MI 390 T3 0.9 3 25 15 -45 +8 +15 2100 ST390-60T3MI 560 T4 0.8 5 40 10 -58 +8 +15 2750 ST560-60T4MI 1000 T4 1.0 12 90 20 -90 +30 +50 3200 ST1000-60T4MI 75 V AT 85 °C; 50 V AT 125 °C DC DC 33 T1 2.5 1 5 66 -25 +5 +9 1050 ST33-75T1MI 110 T2 1.3 2 10 24 -35 +6 +10 1650 ST110-75T2MI 250 L2 0.8 5 30 12 -30 +6 +15 2500 ST250-75L2MI 330 T3 1.0 3 30 12 -45 +6 +10 2100 ST330-75T3MI 470 T4 0.9 5 50 12 -50 +6 +10 2750 ST470-75T4MI Notes • (K = ± 10 %, M = ± 20 %) and insulation letter (I = insulation, X = uninsulated) • Part numbers shown are for units with ± 20 % capacitance tolerance and uninsulated capacitors. For ± 10 units, change the digit following the letter “X” from “0” to “9”. For units with outer plastic-film insulation, substitute “2” for “0” at the end of the part number • For RoHS-compliant add “E3” for suffix Revision: 25-Jun-2018 2 Document Number: 43000 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

ST www.vishay.com Vishay STANDARD RATINGS CAPACITANCE MAX. MAX. DCL AT MAX. IMP. MAXC. CHAAPNAGCEI TAATNCE AC8 R5I P°CPLE AT 25 °C CASE ESR AT -55 °C AND( μ1F2)0 Hz CODE 12(0 H) z +2(μ5A °)C ++81(52μ 5A° C)°C / AND( 12)0 Hz -5(%5 °)C +8(%5 °)C +1(2%5) °C 4R(0m MkAHS)z PART NUMBER 100 V AT 85 °C; 65 V AT 125 °C DC DC 15 T1 3.5 1 5 125 -18 +3 +10 1050 ST15-100T1MI 68 T2 2.1 2 10 37 -30 +4 +12 1650 ST68-100T2MI 120 L2 1.0 3 25 20.5 -30 +4 +12 2200 ST120-100L2MI 150 T3 1.6 3 25 22 -35 +6 +12 2100 ST150-100T3MI 220 T4 1.2 5 50 15 -40 +6 +12 2750 ST220-100T4MI 125 V AT 85 °C; 85 V AT 125 °C DC DC 10 T1 5.5 1 5 175 -15 +3 +10 1050 ST10-125T1MI 47 T2 2.3 2 10 47 -25 +5 +12 1650 ST47-125T2MI 90 L2 1.3 5 25 25 -22 +4 +15 2000 ST90-125L2MI 82 T3 1.8 3 25 40 -35 +5 +12 1950 ST82-125T3MI 100 T3 1.8 3 25 35 -35 +5 +12 2100 ST100-125T3MI 150 T4 1.6 5 50 20 -35 +6 +12 2750 ST150-125T4MI Notes • (K = ± 10 %, M = ± 20 %) and insulation letter (I = insulation, X = uninsulated) • Part numbers shown are for units with ± 20 % capacitance tolerance and uninsulated capacitors. For ± 10 units, change the digit following the letter “X” from “0” to “9”. For units with outer plastic-film insulation, substitute “2” for “0” at the end of the part number • For RoHS-compliant add “E3” for suffix RIPPLE CURRENT MULTIPLIERS VS. FREQUENCY, TEMPERATURE, AND APPLIES PEAK VOLTAGE FREQUENCY OF APPLIED 120 Hz 800 Hz 1 kHz 10 kHz 40 kHz 100 kHz RIPPLE CURRENT AMBIENT STILL  55 85 105 125  55 85 105 125  55 85 105 125  55 85 105 125  55 85 105 125  55 85 105 125 AIR TEMP. IN °C 100 % 0.60 0.39 - - 0.71 0.43 - - 0.72 0.46 - - 0.88 0.55 - - 1.0 0.63 - - 1.1 0.69 - - % of 90 % 0.60 0.46 - - 0.71 0.55 - - 0.72 0.55 - - 0.88 0.67 - - 1.0 0.77 - - 1.1 0.85 - - 85 °C rated 80 % 0.60 0.52 0.35 - 0.71 0.62 0.42 - 0.72 0.62 0.42 - 0.88 0.76 0.52 - 1.0 0.87 0.59 - 1.1 0.96 0.65 - peak voltage 70 % 0.60 0.58 0.44 - 0.71 0.69 0.52 - 0.72 0.70 0.52 - 0.88 0.85 0.64 - 1.0 0.97 0.73 - 1.1 1.07 0.80 - 66 2/3 % 0.60 0.60 0.46 0.27 0.71 0.71 0.55 0.32 0.72 0.72 0.55 0.32 0.88 0.88 0.68 0.40 1.0 1.0 0.77 0.45 1.1 1.1 0.85 0.50 Revision: 25-Jun-2018 3 Document Number: 43000 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

ST www.vishay.com Vishay TYPICAL PERFORMANCE CHARACTERISTICS OF ST CAPACITORS ELECTRICAL CHARACTERISTICS ITEM PERFORMANCE CHARACTERISTICS Operating temperature range -55 °C to +85 °C (to +125 °C with voltage derating) Capacitor tolerance ± 20 %, ± 10 % at 120 Hz, at +25 °C Capacitor change by temperature Limit per Standard Ratings table ESR Limit per Standard Ratings table, at +25 °C, 120 Hz Impedance Limit per Standard Ratings table, at -55 °C, 120 Hz DCL (leakage current) Limit per Standard Ratings table AC ripple current Limit per Standard Ratings table, at +85 °C and 40 kHz Reverse voltage There shall be no continuous reverse voltage. Transient reverse voltage surges are acceptable under the following conditions: a) The peak reverse voltage is equal to or less than 1.5 V and the product of the peak current times the duration of the reverse transient is 0.05 As or less b) The repetition rate of the reverse voltage surges is less than 10 Hz Surge voltage Surge voltage shall be in accordance with MIL-PRF-39006 and Table II of DSCC93026. The DC rated surge voltage is the maximum voltage to which the capacitors can be subjected under any conditions including transients and peak ripple at the highest line voltage. The DC surge voltage is 115 % of rated DC voltage. PERFORMANCE CHARACTERISTICS ITEM PERFORMANCE CHARACTERISTICS Life testing Capacitors shall be capable of withstanding a 2000 h life test at a temperature +85 °C at rated voltage, or a 2000 h life test at 125 °C test at derated voltage. After the test, the capacitors shall meet the following requirements: a) DC leakage at 85 °C and 125 °C shall not exceed 125 % of the specified value b) DC leakage at 25 °C shall not exceed the specified value c) Capacitance shall be within +10 %, -20 % of initial value d) ESR shall not exceed 200 % of the specified value ENVIRONMENTAL CHARACTERISTICS ITEM CONDITION COMMENTS Seal MIL-PRF-39006 When the capacitors are tested as specified in MIL-PRF-39006, there shall be no evidence of leakage. Moisture resistance MIL-PRF-39006 Moisture resistance shall be in accordance with MIL-PRF-39006. Number of cycles: 10 continuous cycles Barometric pressure MIL-STD-202, method 105, condition E Altitude 150 000 feet (reduced) Revision: 25-Jun-2018 4 Document Number: 43000 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

ST www.vishay.com Vishay MECHANICAL CHARACTERISTICS ITEM CONDITION COMMENTS Shock (specified pulse) MIL-STD-202, method 213, condition I The capacitors shall meet the requirements of MIL-PRF-39006. (100 g) Vibration, high frequency MIL-STD-202, method 204, condition D The capacitors shall meet the requirements of MIL-PRF-39006. (20 g peak) Thermal shock MIL-STD-202, method 107, condition A Thermal shock shall be in accordance with MIL-PRF-39006 when tested for 30 cycles. Solderability MIL-STD-202, method 208, Solderability shall be in accordance with MIL-PRF-39006. ANSI/J-STD-002, test A Terminal strength MIL-STD-202, method 211 Terminal strength shall be in accordance with MIL-PRF-39006. Resistance to solder heat MIL-STD-202, method 210, condition C The capacitors shall meet the requirements of MIL-PRF-39006. Terminals MIL-STD-1276 Terminals shall be as specified in MIL-STD-1276. The length and diameter of the terminals shall be as specified in Dimensions table. All terminals shall be permanently secured internally and externally, as applicable. All external joints shall be welded. Marking MIL-STD-1285 Marking of capacitors conforms to method I of MIL-STD-1285 and include capacitance (in μF), capacitance tolerance letter, rated voltage, date code, lot symbol and Vishay trademark. SELECTOR GUIDES Tantalum Selector Guide www.vishay.com/doc?49054 Parameter Comparison Guide www.vishay.com/doc?42088 Revision: 25-Jun-2018 5 Document Number: 43000 For technical questions, contact: tantalum@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROV E RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose o r the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustainin g applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk . Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this documen t or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2019 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 01-Jan-2019 1 Document Number: 91000

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: V ishay: ST4ETB502 ST4ETA203 ST32TA 100 ST4ETA101 ST4ETA103 ST4ETA104