Transient Voltage Suppression Diodes Surface Mount – 3000W > SMDJ series SMDJ Series RoHS Pb e3 Uni-directional Description The SMDJ series is designed specifically to protect Bi-directional sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Features • 3000W peak pulse power • Excellent clamping capability at 10/1000μs capability waveform, repetition rate • Low incremental surge (duty cycles):0.01% resistance • For surface mounted • Typical I less than 2μA Agency Approvals applications in order to when VR min>12V BR optimize board space AGENCY AGENCY FILE NUMBER • High temperature • Low profile package to reflow soldering E230531 • Typical failure mode is guaranteed: 260°C/40sec short from over-specified • V @ T= V @25°C Maximum Ratings and Thermal Characteristics BR J BR (T =25OC unless otherwise noted) voltage or current x (1+αT x (TJ - 25)) A • Whisker test is conducted (αT:Temperature Parameter Symbol Value Unit based on JEDEC Coefficient, typical value Peak Pulse Power Dissipation at JESD201A per its table 4a is 0.1%) T =25ºC by 10/1000µs Waveform P 3000 W and 4c • Plastic package is A PPM (Fig.2)(Note 1), (Note 2), (Note 5) • IEC-61000-4-2 ESD flammability rated V-0 per Power Dissipation on Infinite Heat 30kV(Air), 30kV (Contact) Underwriters Laboratories P 6.5 W Sink at T=50OC D L • ESD protection of data • Meet MSL level1, per Peak Forward Surge Current, 8.3ms lines in accordance with J-STD-020, LF maximun I 300 A Single Half Sine Wave (Note 3) FSM IEC 61000-4-2 peak of 260°C Maximum Instantaneous Forward • EFT protection of data • Matte tin lead–free plated Voltage at 100A for Unidirectional V 3.5/5.0 V Only(Note 4) F lines in accordance with • Halogen free and RoHS IEC 61000-4-4 compliant Operating Temperature Range T -65 to 150 °C J • Built-in strain relief • Pb-free E3 means 2nd Storage Temperature Range T -65 to 175 °C STG • Glass passivated chip level interconnect is Typical Thermal Resistance Junction junction Pb-free and the terminal R 15 °C/W to Lead θJL • Fast response time: finish material is tin(Sn) Typical Thermal Resistance Junction R 75 °C/W typically less than 1.0ps (IPC/JEDEC J-STD- to Ambient θJA from 0V to BV min 609A.01) Notes: 1. Non-repetitive current pulse , per Fig. 4 and derated above TJ (initial) =25OC per Fig. 3. Applications 2. Mounted on copper pad area of 0.31x0.31” (8.0 x 8.0mm) to each terminal. 3. Measured on 8.3ms single half sine wave or equivalent square wave for unidirectional TVS devices are ideal for the protection of I/O Interfaces, device only, duty cycle=4 per minute maximum. V bus and other vulnerable circuits used in Telecom, 4. V < 3.5V for single die parts and V< 5.0V for stacked-die parts. CC F F Computer, Industrial and Consumer electronic 5. The P of stacked-die parts is 4000W and please contact littelfuse for the detail stackePPdM-die parts. applications. Functional Diagram Additional Infomarion Bi-directional Datasheet Resources Samples Cathode Anode Uni-directional © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/20/15

Transient Voltage Suppression Diodes Surface Mount – 3000W > SMDJ series Electrical Characteristics (T=25°C unless otherwise noted) A Reverse Breakdown Test Maximum Maximum Maximum Agency NuPmarbt e r NuPmarbt e r Marking SVtoanltdag oef f Voltage VBR Current VColaltmagpein Vg PPuelaske LReaekvaegrsee I Approval (Uni) (Bi) V (Volts) @ IT IT @ I C Current I @ V R R pp pp R UNI BI (Volts) MIN MAX (mA) (V) (A) (µA) SMDJ5.0A SMDJ5.0CA RDE DDE 5.0 6.40 7.00 10 9.2 326.1 800 X SMDJ6.0A SMDJ6.0CA RDG DDG 6.0 6.67 7.37 10 10.3 291.3 800 X SMDJ6.5A SMDJ6.5CA RDK DDK 6.5 7.22 7.98 10 11.2 267.9 500 X SMDJ7.0A SMDJ7.0CA PDM DDM 7.0 7.78 8.60 10 12.0 250.0 200 X SMDJ7.5A SMDJ7.5CA PDP DDP 7.5 8.33 9.21 1 12.9 232.6 100 X SMDJ8.0A SMDJ8.0CA PDR DDR 8.0 8.89 9.83 1 13.6 220.6 50 X SMDJ8.5A SMDJ8.5CA PDT DDT 8.5 9.44 10.40 1 14.4 208.3 20 X SMDJ9.0A SMDJ9.0CA PDV DDV 9.0 10.00 11.10 1 15.4 194.8 10 X SMDJ10A SMDJ10CA PDX DDX 10.0 11.10 12.30 1 17.0 176.5 5 X SMDJ11A SMDJ11CA PDZ DDZ 11.0 12.20 13.50 1 18.2 164.8 2 X SMDJ12A SMDJ12CA PEE DEE 12.0 13.30 14.70 1 19.9 150.8 2 X SMDJ13A SMDJ13CA PEG DEG 13.0 14.40 15.90 1 21.5 139.5 2 X SMDJ14A SMDJ14CA PEK DEK 14.0 15.60 17.20 1 23.2 129.3 2 X SMDJ15A SMDJ15CA PEM DEM 15.0 16.70 18.50 1 24.4 123.0 2 X SMDJ16A SMDJ16CA PEP DEP 16.0 17.80 19.70 1 26.0 115.4 2 X SMDJ17A SMDJ17CA PER DER 17.0 18.90 20.90 1 27.6 108.7 2 X SMDJ18A SMDJ18CA PET DET 18.0 20.00 22.10 1 29.2 102.7 2 X SMDJ20A SMDJ20CA PEV DEV 20.0 22.20 24.50 1 32.4 92.6 2 X SMDJ22A SMDJ22CA PEX DEX 22.0 24.40 26.90 1 35.5 84.5 2 X SMDJ24A SMDJ24CA PEZ DEZ 24.0 26.70 29.50 1 38.9 77.1 2 X SMDJ26A SMDJ26CA PFE DFE 26.0 28.90 31.90 1 42.1 71.3 2 X SMDJ28A SMDJ28CA PFG DFG 28.0 31.10 34.40 1 45.4 66.1 2 X SMDJ30A SMDJ30CA PFK DFK 30.0 33.30 36.80 1 48.4 62.0 2 X SMDJ33A SMDJ33CA PFM DFM 33.0 36.70 40.60 1 53.3 56.3 2 X SMDJ36A SMDJ36CA PFP DFP 36.0 40.00 44.20 1 58.1 51.6 2 X SMDJ40A SMDJ40CA PFR DFR 40.0 44.40 49.10 1 64.5 46.5 2 X SMDJ43A SMDJ43CA PFT DFT 43.0 47.80 52.80 1 69.4 43.2 2 X SMDJ45A SMDJ45CA PFV DFV 45.0 50.00 55.30 1 72.7 41.3 2 X SMDJ48A SMDJ48CA PFX DFX 48.0 53.30 58.90 1 77.4 38.8 2 X SMDJ51A SMDJ51CA PFZ DFZ 51.0 56.70 62.70 1 82.4 36.4 2 X SMDJ54A SMDJ54CA RGE DGE 54.0 60.00 66.30 1 87.1 34.4 2 X SMDJ58A SMDJ58CA PGG DGG 58.0 64.40 71.20 1 93.6 32.1 2 X SMDJ60A SMDJ60CA PGK DGK 60.0 66.70 73.70 1 96.8 31.0 2 X SMDJ64A SMDJ64CA PGM DGM 64.0 71.10 78.60 1 103.0 29.1 2 X SMDJ70A SMDJ70CA PGP DGP 70.0 77.80 86.00 1 113.0 26.5 2 X SMDJ75A SMDJ75CA PGR DGR 75.0 83.30 92.10 1 121.0 24.8 2 X SMDJ78A SMDJ78CA PGT DGT 78.0 86.70 95.80 1 126.0 23.8 2 X SMDJ85A SMDJ85CA PGV DGV 85.0 94.40 104.00 1 137.0 21.9 2 X SMDJ90A SMDJ90CA PGX DGX 90.0 100.00 111.00 1 146.0 20.5 2 X SMDJ100A SMDJ100CA PGZ DGZ 100.0 111.00 123.00 1 162.0 18.5 2 X SMDJ110A SMDJ110CA PHE DHE 110.0 122.00 135.00 1 177.0 16.9 2 X SMDJ120A SMDJ120CA PHG DHG 120.0 133.00 147.00 1 193.0 15.5 2 X SMDJ130A SMDJ130CA PHK DHK 130.0 144.00 159.00 1 209.0 14.4 2 X SMDJ150A SMDJ150CA PHM DHM 150.0 167.00 185.00 1 243.0 12.3 2 X SMDJ160A SMDJ160CA PHP DHP 160.0 178.00 197.00 1 259.0 11.6 2 X SMDJ170A SMDJ170CA PHR DHR 170.0 189.00 209.00 1 275.0 10.9 2 X SMDJ180A SMDJ180CA PHT DHT 180.0 200.00 221.00 1 292.0 10.3 2 X SMDJ220A SMDJ220CA PKE DKE 220.0 244.00 270.00 1 356.0 8.4 2 X For bidirectional type having V of 10 volts and less, the I limit is double. R R For parts without A , the V is ± 10% and V is 5% higher than with A parts BR C © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/20/15

Transient Voltage Suppression Diodes Surface Mount – 3000W > SMDJ series I-V Curve Characteristics Bi-directional Uni-directional Ipp IT Vc VBRVR IR V IR VRVBRVc Vc VBRVR V IT IRVF IT Ipp Ipp P Peak Pulse Power Dissipation -- Max power dissipation PPM V Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation R V Breakdown Voltage -- Maximum voltage that flows though the TVS at a specified test current (I) BR T V Clamping Voltage -- Peak voltage measured across the TVS at a specified Ippm (peak impulse current) C I Reverse Leakage Current -- Current measured at V R R V Forward Voltage Drop for Uni-directional F Ratings and Characteristic Curves (T=25°C unless otherwise noted) A Figure 1 - TVS Transients Clamping Waveform Figure 2 - Peak Pulse Power Rating Voltage Transients W)100 stacked-die, 4kW k er ( at 10x1000µs, 25°C w Voltage Across TVS o P10 nt e urre uls Single die, 3kW C Current Through TVS P at 10x1000µs, 25°C e or ak Voltag -PeM 1 P P P TJ initial = Tamb 0.1 0.001 0.01 0.1 1 10 t-Pulse Width (ms) Time d continues on next page. © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/20/15

Transient Voltage Suppression Diodes Surface Mount – 3000W > SMDJ series Ratings and Characteristic Curves (T=25°C unless otherwise noted) (Continued) A Figure 3 - Peak Pulse Power Derating Curve Figure 4 - Pulse Waveform 100 e Power (P) or Current (I)PPPPating in Percentage % 468000 Peak Pulse Current, % IRSM 11505000 tr=1PI0PeµPasMke cVaHIlPuaPelMf Va(lI Pu P1a2eTPac0sM usuJ / rd1=)ltrsh02eeee50nfi W °0tpnC dµioedeisdtnceh tabc( wyt.yds hW ) R teiosar. E ev5d .0eteAh%ffieon orpemfde IaPkP M k PulsDer 20 I- PPM ea td P 0 0 0 1.0 2.0 3.0 4.0 0 25 50 75 100 125 150 175 t-Time (ms) T - Initial Junction Temperature (ºC) J Figure 5 - Typical Junction Capacitance Figure 6 - Typical Transient Thermal Impedance 100000 100 Uni-direc(cid:31)onal V=0V W) C/ 10000 Bi-direc(cid:31)onal V=0V °ce ( 10 n a Uni-direc(cid:31)onal V=V d F) 1000 R pe p m Cj( 100 Bi-direc(cid:31)onal V=VR mal I 1 er h T nt 0.1 10 e si n a Tr 1 0.01 1 10 100 1000 0.001 0.01 0.1 1 10 100 1000 VBR-Reverse Breakdown Voltage(V) T -Pulse Duration (s) P Figure 7 - Maximum Non-Repetitive Peak Forward Figure 8 - Peak Forward Voltage Drop vs Peak Forward Surge Current Uni-Directional Only Current (Typical Values) 500 100 Single die 450 ent (A) 400 nt(A) Peak Forward Surve Curr 122335050500000 Peak Forward Curre 01.110 Stack-die -M 100 -F FS I I 50 0.01 0 0.00 1.00 2.00 3.00 4.00 5.00 6.00 7.00 8.00 1 10 100 VF-Peak Forward Voltage(V) Number of Cycles at 60 Hz © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/20/15

Transient Voltage Suppression Diodes Surface Mount – 3000W > SMDJ series Soldering Parameters Lead–free Reflow Condition assembly TP tp - Temperature Min (T ) 150°C s(min) Ramp-up Critical Zone Pre Heat -- TTeimmep e(mraitnu rteo Mmaaxx) ((Ttss()max)) 6200 0–° C180 secs (T)ure Ts(mTaLx) tL TL to TP Atov epreaagke ramp up rate (Liquidus Temp (TA) 3°C/second max TemperatTs(min) Prethseat Ramp-down T to T - Ramp-up Rate 3°C/second max S(max) A - Temperature (T ) (Liquidus) 217°C Reflow A 25˚C t 25˚C to Peak - Time (min to max) (t) 60 – 150 seconds Time (t) s Peak Temperature (T) 260+0/-5 °C P Time within 5°C of actual peak 20 – 40 seconds Temperature (t) p Ramp-down Rate 6°C/second max Environmental Specifications Time 25°C to peak Temperature (T) 8 minutes Max. P Do not exceed 260°C High Temp. Storage JESD22-A103 Physical Specifications HTRB JESD22-A108 Weight 0.007 ounce, 0.21 grams Temperature Cycling JESD22-A104 JEDEC DO214AB. Molded plastic body Case over glass passivated junction MSL JEDEC-J-STD-020, Level 1 Color band denotes positive end Polarity (cathode) except Bidirectional. H3TRB JESD22-A101 Matte Tin-plated leads, Solderable per Terminal RSH JESD22-A111 JESD22-B102 Dimensions DO-214AB (SMC J-Bend) Cathode Band Inches Millimeters (for Uni-directional products only) Dimensions Min Max Min Max A 0.114 0.126 2.900 3.200 A C B 0.260 0.280 6.600 7.110 C 0.220 0.245 5.590 6.220 B D 0.079 0.103 2.060 2.620 E 0.030 0.060 0.760 1.520 H F - 0.008 - 0.203 D G 0.305 0.320 7.750 8.130 F H 0.006 0.012 0.152 0.305 E G I 0.129 - 3.300 - J K L J 0.094 - 2.400 - K - 0.165 4.200 I L 0.094 - 2.400 - Solder Pads (all dimensions in mm) © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/20/15

Transient Voltage Suppression Diodes Surface Mount – 3000W > SMDJ series Part Numbering System Part Marking System SMDJ XXXCA Cathode Band (for Uni-directional products only) F Littelfuse Logo 5% V VOLTAGE TOLERANCE BR BI-DIRECTIONAL XXX Marking Code VVOLTAGE R YMXXX SERIES Trace Code Marking Y:Year Code M: Month Code XXX: Lot Code Packaging Options Component Packaging Packaging Part number Quantity Package Option Specification SMDJxxxXX DO-214AB 3000 Tape & Reel - 16mm tape/13” reel EIA STD RS-481 SMDJxxxXX-T7 DO-214AB 500 Tape & Reel – 16mm tape/7” reel EIA STD RS-481 Tape and Reel Specification 0.157 (4.0) 0.63 (16.0) Cathode 0.315 0.059 DIA Cover tape (8.0) (1.5) Optional 7” 7.0 (187) 13” 13.0 (330) Dimensions are in inches 0.80 (20.2) (and millimeters). Arbor Hole Dia. Direction of Feed 0.65 (16.4) © 2015 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 11/20/15