DATA SHEET SKY13290-313LF: 20 MHz-2.5 GHz, 10 W pHEMT SPDT Switch Applications • Transmit/receive switching for telematic systems at elevated power levels Features • Broadband frequency range: 20 MHz to 2.5 GHz • Very low insertion loss, 0.4 dB typical @ 0.9 GHz • High isolation: 26 dB typical @ 0.9 GHz • High input power compression: 0.1 dB @ > +40 dBm • Low current consumption: <100 μA @ 3 V Figure 1. SKY13290-313LF Block Diagram • Ultra-miniature, QFN (6-pin, 2 x 3 mm) package (MSL1, 260 °C per JEDEC J-STD-020) Description The SKY13290-313LF is a high power, pHEMT Single Pole Double Throw (SPDT) switch. The switch is designed for use in systems operating from 20 MHz to 2.5 GHz for which low loss, high isolation, low control voltage, and ultra-miniature package size are required. The device is controlled with positive, negative, or a combination of both voltages. The RF signal paths within the device are fully bilateral. The SKY13290-313LF is manufactured in a compact, low-cost 2 x 3 mm, 6-pin Quad Flat No-Lead (QFN) package. A functional block diagram is shown in Figure 1. The pin configuration and package are shown in Figure 2. Signal pin assignments and functional pin descriptions are provided in Table 1. Figure 2. SKY13290-313LF Pinout –6-Pin QFN (Top View) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 200488G • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • March 11, 2013 1

DATA SHEET • SKY13290-313LF SPDT SWITCH Table 1. SKY13290-313LF Signal Descriptions Pin # Name Description Pin # Name Description 1 J2 RF input/output. According to the logic 4 V2 DC control voltage input #2. The logic voltage levels applied to the V1 and V2 pins, voltage applied to this pin, along with the this port is either connected to J1 using a voltage level applied to the V1 pin, low insertion loss path or isolated from J1 determines the states of the RF paths (Note 1). between J1/J2 and J1/J3. 2 GND Ground. Equipotential port, internal circuit 5 J1 RF input/output. According to the logic common, which must connected to the PCB voltage levels applied to the V1 and V2 pins, ground or common using the lowest this port is either connected to J2 or to J3 possible impedance. using a low insertion loss path and isolated from the other RF port (Note 1). 3 J3 RF input/output. According to the logic 6 V1 DC control voltage input #1. The logic voltage levels applied to the V1 and V2 pins, voltage applied to this pin, along with the this port is either connected to J1 using a voltage level applied to the V2 pin, low insertion loss path or isolated from J1 determines the states of the RF paths (Note 1). between J1/J2 and J1/J3. Note 1: A 47 pF blocking capacitor is required for >500 MHz operation. Use larger value capacitors for lower frequency operation. Table 2. SKY13290-313LF Absolute Maximum Ratings Parameter Symbol Minimum Maximum Units Control voltage VCTL 0 +10 V RF input power (VCTL > 0.9 GHz) PIN +43.5 dBm Operating temperature TOP –40 +85 °C Storage temperature TSTG –65 +150 °C Electrostatic Discharge, Human Body Model (HBM), Class 1A 250 V Note: Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters set at or below their nominal value. CAUTION: Although this device is designed to be as robust as possible, Electrostatic Discharge (ESD) can damage this device. This device must be protected at all times from ESD. Static charges may easily produce potentials of several kilovolts on the human body or equipment, which can discharge without detection. Industry-standard ESD precautions should be used at all times. Technical Description Electrical and Mechanical Specifications The SKY13290-313LF is controlled using two voltage inputs, V1 The absolute maximum ratings of the SKY13290-313LF are and V2 (pins 6 and 4, respectively). Depending on the voltage level provided in Table 2. Electrical specifications are provided in applied to these pins, the common RF port (J1) is connected to Table 3 and the operating characteristics are specified in Table 4. one of two RF ports (J2 or J3) using a low insertion loss path, Typical performance characteristics of the SKY13290-313LF are while the path between J1 and the other RF port is in its isolation illustrated in Figures 3 through 6. state. The state of the SKY13290-313LF is determined by the logic When the control voltages are toggled, the states between J1 and provided in Table 5. J2, as well as J1 and J3, are also toggled. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 2 March 11, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 200488G

DATA SHEET • SKY13290-313LF SPDT SWITCH Table 3. SKY13290-313LF Electrical Specifications (Note 1) (VCTL = 0-3 V, TOP = +25 °C, PIN = 0 dBm, Characteristic Impedance = 50 Ω, Unless Otherwise Noted) Parameter Symbol Test Condition Min Typical Max Units Insertion loss 0.02 to 1.0 GHz 0.40 0.50 dB 1.0 to 2.0 GHz 0.45 0.60 dB 2.0 to 2.5 GHz 0.55 0.70 dB Isolation 0.02 to 1.0 GHz 23 26 dB 1.0 to 2.0 GHz 17 20 dB 2.0 to 2.5 GHz 15 18 dB Return loss (Note 2) 0.02 to 1.0 GHz 20 dB 1.0 to 2.5 GHz 20 dB Switching characteristics: Rise/fall 10/90% or 90/10% RF 650 ns On/off 50% VCTL to 90/10% RF 800 ns 0.1 dB Input Compression Point IP0.1dB @ 48 MHz +37.6 dBm @ 900 MHz +40.5 dBm Thermal resistance 45 °C/W Control voltage: Low (@ 20 μA max) VCTL_L 0 V High (@100 μA max) VCTL_H 2.7 V High (@ 200 μA max) VCTL_H 10.0 V Note 1: Performance is guaranteed only under the conditions listed in this Table. Note 2: Return loss state. Lower frequency return loss is dependent on value of the DC blocking capacitors. Typical Performance Characteristics (VCTL = 0-3 V, TOP = +25 °C, PIN = 0 dBm, Characteristic Impedance [ZO] = 50 Ω, CBL = 100 pF, Unless Otherwise Noted) Figure 3. Insertion Loss vs Frequency Figure 4. Isolation vs Frequency Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 200488G • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • March 11, 2013 3

DATA SHEET • SKY13290-313LF SPDT SWITCH Figure 5. Return Loss vs Frequency Figure 6. Insertion Loss vs Input Power (Insertion Loss State) (@ 900 MHz) Table 4. Truth Table (VHIGH = 2 to 5 V) V1 V2 J1-J2 J1-J3 VLOW VHIGH Isolation Insertion loss VHIGH VLOW Insertion loss Isolation Note: VLOW = 0 to 0.2 V, VHIGH = 2.7 to 10 V. Any state other than described in this Table places the device in an undefined state. An undefined state does not damage the device. Evaluation Board Description Package and Handling Information The SKY13290-313LF Evaluation Board is used to test the Instructions on the shipping container label regarding exposure to performance of the SKY13290-313LF SPDT switch. An Evaluation moisture after the container seal is broken must be followed. Board schematic diagram is provided in Figure 7. An assembly Otherwise, problems related to moisture absorption may occur drawing for the Evaluation Board is shown in Figure 8. when the part is subjected to high temperature during solder assembly. The SKY13290-313LF is rated to Moisture Sensitivity Level 1 Package Dimensions (MSL1) at 260 °C. It can be used for lead or lead-free soldering. The PCB layout footprint for the SKY13290-313LF is shown in Care must be taken when attaching this product, whether it is Figure 9. Typical case markings are shown in Figure 10. Package done manually or in a production solder reflow environment. dimensions for the 6-pin QFN are shown in Figure 11, and tape Production quantities of this product are shipped in a standard and reel dimensions are provided in Figure 12. tape and reel format. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 4 March 11, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 200488G

DATA SHEET • SKY13290-313LF SPDT SWITCH Figure 7. SKY13290-313LF Evaluation Board Schematic Figure 8. SKY13290-313LF Evaluation Board Assembly Diagram Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 200488G • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • March 11, 2013 5

DATA SHEET • SKY13290-313LF SPDT SWITCH Figure 9. SKY13290-313LF PCB Layout Footprint Figure 10. Typical Case Markings (Top View) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 6 March 11, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 200488G

DATA SHEET • SKY13290-313LF SPDT SWITCH Figure 11. SKY13290-313LF 6-Pin QFN Package Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 200488G • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • March 11, 2013 7

DATA SHEET • SKY13290-313LF SPDT SWITCH Figure 12. SKY13290-313LF Tape and Reel Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 8 March 11, 2013 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 200488G

DATA SHEET • SKY13290-313LF SPDT SWITCH Ordering Information Model Name Manufacturing Part Number Evaluation Board Part Number SKY13290-313LF SPDT Switch SKY13290-313LF SKY13290-313LF-EVB Copyright © 2002-2007, 2010, 2013 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 200488G • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • March 11, 2013 9