P51E.pdf Sep.10,2019 Ceramic Filters (CERAFIL)/ Crystal Filters

!Note (cid:129) Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. P51E.pdf (cid:129) This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.10,2019 EU RoHS Compliant (cid:70)(cid:3)(cid:5)(cid:42)(cid:42)(cid:3)(cid:50)(cid:38)(cid:35)(cid:3)(cid:46)(cid:48)(cid:45)(cid:34)(cid:51)(cid:33)(cid:50)(cid:49)(cid:3)(cid:39)(cid:44)(cid:3)(cid:50)(cid:38)(cid:39)(cid:49)(cid:3)(cid:33)(cid:31)(cid:50)(cid:31)(cid:42)(cid:45)(cid:37)(cid:3)(cid:33)(cid:45)(cid:43)(cid:46)(cid:42)(cid:55)(cid:3) (cid:53)(cid:39)(cid:50)(cid:38)(cid:3)(cid:9)(cid:25)(cid:3)(cid:22)(cid:45)(cid:12)(cid:23)(cid:64) (cid:70)(cid:3)(cid:9)(cid:25)(cid:3)(cid:22)(cid:45)(cid:12)(cid:23)(cid:3)(cid:39)(cid:49)(cid:3)(cid:159)(cid:50)(cid:38)(cid:35)(cid:3)(cid:9)(cid:51)(cid:48)(cid:45)(cid:46)(cid:35)(cid:31)(cid:44)(cid:3)(cid:8)(cid:39)(cid:48)(cid:35)(cid:33)(cid:50)(cid:39)(cid:52)(cid:35)(cid:3) (cid:124)(cid:122)(cid:123)(cid:123)(cid:71)(cid:128)(cid:127)(cid:71)(cid:9)(cid:25)(cid:3)(cid:45)(cid:44)(cid:3)(cid:50)(cid:38)(cid:35)(cid:3)(cid:22)(cid:35)(cid:49)(cid:50)(cid:48)(cid:39)(cid:33)(cid:50)(cid:39)(cid:45)(cid:44)(cid:3)(cid:45)(cid:36)(cid:3)(cid:50)(cid:38)(cid:35)(cid:3) (cid:25)(cid:49)(cid:35)(cid:3)(cid:45)(cid:36)(cid:3)(cid:7)(cid:35)(cid:48)(cid:50)(cid:31)(cid:39)(cid:44)(cid:3)(cid:12)(cid:31)(cid:56)(cid:31)(cid:48)(cid:34)(cid:45)(cid:51)(cid:49)(cid:3)(cid:23)(cid:51)(cid:32)(cid:49)(cid:50)(cid:31)(cid:44)(cid:33)(cid:35)(cid:49)(cid:3)(cid:39)(cid:44)(cid:3) (cid:9)(cid:42)(cid:35)(cid:33)(cid:50)(cid:48)(cid:39)(cid:33)(cid:31)(cid:42)(cid:3)(cid:31)(cid:44)(cid:34)(cid:3)(cid:9)(cid:42)(cid:35)(cid:33)(cid:50)(cid:48)(cid:45)(cid:44)(cid:39)(cid:33)(cid:3)(cid:9)(cid:47)(cid:51)(cid:39)(cid:46)(cid:43)(cid:35)(cid:44)(cid:50)(cid:64)(cid:159)(cid:3) (cid:70)(cid:3)For(cid:3)(cid:43)(cid:45)(cid:48)(cid:35)(cid:3)(cid:34)(cid:35)(cid:50)(cid:31)(cid:39)(cid:42)(cid:49)(cid:65)(cid:3)(cid:46)(cid:42)(cid:35)(cid:31)(cid:49)(cid:35)(cid:3)(cid:48)(cid:35)(cid:36)(cid:35)r(cid:3)(cid:50)o(cid:3)(cid:45)ur(cid:3)(cid:53)(cid:35)(cid:32)(cid:3) (cid:46)(cid:31)(cid:37)(cid:35)(cid:65)(cid:3)(cid:159)(cid:17)(cid:51)(cid:48)(cid:31)(cid:50)(cid:31)(cid:158)(cid:49)(cid:3)(cid:5)(cid:46)(cid:46)(cid:48)(cid:45)(cid:31)(cid:33)(cid:38)(cid:3)(cid:36)(cid:45)(cid:48)(cid:3)(cid:9)(cid:25)(cid:3)(cid:22)(cid:45)(cid:12)(cid:23)(cid:159)(cid:3) (cid:72)(cid:38)(cid:50)(cid:50)(cid:46)(cid:49)(cid:66)(cid:71)(cid:71)(cid:53)(cid:53)(cid:53)(cid:64)(cid:43)(cid:51)(cid:48)(cid:31)(cid:50)(cid:31)(cid:64)(cid:33)(cid:45)(cid:43)(cid:71)(cid:35)(cid:44)(cid:81)(cid:35)(cid:51)(cid:71)(cid:49)(cid:51)(cid:46)(cid:46)(cid:45)(cid:48)(cid:50)(cid:71) (cid:33)(cid:45)(cid:43)(cid:46)(cid:42)(cid:39)(cid:31)(cid:44)(cid:33)(cid:35)(cid:71)(cid:48)(cid:45)(cid:38)(cid:49)(cid:74)(cid:64)(cid:3)

!Note (cid:129) Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. P51E.pdf (cid:129) This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.10,2019 1 Contents Product specifications are as of October 2019. 2 Selection Guide p2 Part Numbering p3 Ceramic Filters (CERAFIL) Chip Type SFECF Series 1 Features/Appearance/Dimensions p6 Part Number List p6 3 Standard Center Frequency Rank Code p7 Standard Land Pattern Dimensions p7 Test Circuit p7 Frequency Characteristics p8 Spurious p10 Notice p12 Packaging p14 4 Ceramic Filters (CERAFIL) Chip Type SFECV/SFECK Series 2 Features/Applications/Appearance/Dimensions p15 Part Number List p15 Standard Center Frequency Rank Code p16 Standard Land Pattern Dimensions p16 Test Circuit p16 Frequency Characteristics p16 Spurious p17 Notice p18 Packaging p20 Ceramic Discriminator (CERAFIL) Chip Type CDSCB Series 3 Features/Appearance/Dimensions p21 Part Number List p21 Standard Center Frequency Rank Code p21 Standard Land Pattern Dimensions p22 Test Circuit p22 Recovered Audio Curve p24 S Curve p25 Notice p26 Packaging p28 Crystal Filters Chip Type XDCAF/XDCAG/XDCAH/XDCBA Series 4 Features/Applications/Appearance/Dimensions p29 Series p29 Part Number List p30 Test Circuit p31 Frequency Characteristics p32 Spurious p33 Notice p34 Packaging p36 Please check the MURATA website (https://www.murata.com/) if you cannot find a part number in this catalog.

!Note (cid:129) Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. P51E.pdf (cid:129) This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.10,2019 Selection Guides Applications Audio Visual/Communications Industrial Filters Discriminators Crystal Filters SFECF CDSCB XDCAF 3.45×3.1×1.4mm 4.5×2.0×1.0mm 7.0×5.0×1.1mm 10.000-11.000MHz 10.520-10.800MHz 2 poles SFECV/SFECK XDCAG 6.9×2.9×1.7mm 7.0×5.0×1.1mm 10.700-15.000MHz 4 poles XDCAH 7.0×5.0×1.1mm 4 poles XDCBA 3.8×3.8×1.0mm 2 poles 2

!Note (cid:129) Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. P51E.pdf (cid:129) This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.10,2019 o Part Numbering CERAFIL for FM (Part Number) SF E CF 10M7 F A A0 -R0 1 2 3 4 5 6 7 8 1Product ID 6Center Frequency/Tolerance Product ID Code Center Frequency Tolerance SF Ceramic Filters A Center Frequency Mentioned by Specification ±30kHz F Nominal Center Frequency — 2Oscillation/Number of Elements 3dB bandwidth of "F" signifies the frequency difference (both + and -) Code Oscillation/Number of Elements from reference frequency, which is nominal center frequency. E 2 Elements Thickness Expander Mode T 3 Elements Thickness Expander Mode 7Series 2 Elements Thickness Expander Mode Code Series V (2nd Harmonic) A0 Two-digit Alphanumerics Express Series 2 Elements Thickness Expander Mode K (3rd Overtone) 8Packaging Code Packaging 3Structure/Size -B0 Bulk Code Structure/Size -R0 Embossed Taping ø180mm Cp Chip Type -R1 Embossed Taping ø330mm p is "A" or subsequent code, which indicates the structure/size. Radial taping is applied to lead type and embossed taping to chip type. With non-standard products, two-digit alphanumerics indicating 4Nominal Center Frequency "Individual Specification" are added between "7Series" and "8Packaging." Expressed by four-digit alphanumerics. The unit is in hertz (Hz). Decimal point is expressed by capital letter "M" in case of MHz. 53dB Bandwidth Code 3dB Bandwidth C 450kHz min D 350kHz min E 330kHz F 280kHz G 230kHz H 180kHz J 150kHz K 110kHz L 80kHz M 50kHz N 35kHz 3

!Note (cid:129) Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. P51E.pdf (cid:129) This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.10,2019 CERAFIL (Part Number) SF S KA 4M50 CF 00 -R1 1 2 3 4 5 6 7 1Product ID 5Product Specification Code (1) Product ID Code Product Specification Code (1) SF Ceramic Filters BF Tight Bandwidth Type CF Standard Bandwidth Type 2Oscillation/Numbers of Element DF Broad Bandwidth Type Code Oscillation/Numbers of Element EF Ultra-broad Bandwidth Type S 2 Elements Thickness Shear Mode 6Product Specification Code (2) 3Structure/Size Code Product Specification Code (2) Code Structure/Size 00 Standard Type Kp Chip Type p is "A" or subsequent code, which indicates the structure/size. 7Packaging Code Packaging 4Nominal Center Frequency -B0 Bulk Expressed by four-digit alphanumerics. The unit is in hertz (Hz). -R1 Embossed Taping ø=330mm Decimal point is expressed by capital letter "M" in case of MHz. With non-standard products, two-digit alphanumerics indicating "Individual Specification" is added between "6Product Specification Code (2)" and "7Packaging." Discriminators for FM (Part Number) CD S CB 10M7 G A 001 -R0 1 2 3 4 5 6 7 8 1Product ID 6Center Frequency/Tolerance Product ID Code Center Frequency Tolerance CD Discriminators A Center Frequency Mentioned by Specification ±30kHz F Nominal Center Frequency — 2Oscillation 3dB bandwidth of "F" signifies the frequency difference (both + and -) Code Oscillation from reference frequency, which is nominal center frequency. S Thickness Shear Mode 7IC 3Structure/Size Code IC Code Structure/Size 001 Applicable IC Control Code Cp Chip Type p is "A" or subsequent code, which indicates the structure/size. 8Packaging Code Packaging 4Nominal Center Frequency -B0 Bulk Expressed by four-digit alphanumerics. The unit is in hertz (Hz). -R0 Embossed Taping ø=180mm Decimal point is expressed by capital letter "M" in case of MHz. -R1 Embossed Taping ø=330mm Radial taping is applied to lead type and embossed taping to chip type. 5Series With non-standard products, an alphanumerics indicating "Individual Specification" is added between "7IC" and "8Packaging." Code Series G Two-digit Alphanumerics Express Series 4

!Note (cid:129) Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. P51E.pdf (cid:129) This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.10,2019 Crystal Filter (Part Number) XD C A F 21M400 R A A00 P0 1 2 3 4 5 6 7 8 9 1Product ID 7Number of Poles Product ID Code Number of Poles XD Crystal Filter A 2 (1 Element) G 4 (1 Element) 2Type · Lead Style H 4 (2 Elements) Code Type · Lead Style C Monolithic SMD 8Individual Specification Code 3Size Three-digit Alphanumerics Express *** Code Size Individual Specification. A 7050 B 3838 9Packaging (Packaging quantity is expressed by one-digit number in "*") 4Structure Code Packaging Expressed by one alphabetic character. P*/L* Plastic Taping ø330mm 5Nominal Center Frequency Expressed by six-digit alphanumeric. The unit is in hertz (Hz). Decimal point is expressed by capital letter "M". 6Bandwidth Code Bandwidth (3dB) M 6.800 to 8.199kHz P 10.000 to 11.999kHz Q 12.000 to 14.999kHz R 15.000 to 17.999kHz 5

!Note (cid:129) Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. P51E.pdf (cid:129) This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.10,2019 Ceramic Filters (CERAFIL) 1 RoHS Chip Type SFECF Series 3.45±0.2 1.3±0.1 The SFECF10M7 series for FM receivers are small, 2 high-performance and super thin (1.4mm max.) filters. 0. Input electrode 1± The piezoelectric element is sandwiched by ceramic marker 3. substrate. They have 1.4mm max. thickness and a small 0 to 0.4(0.6)(0.6)(0.6)0 to 0.4 mounting area (3.45x3.1mm). The SFECF series and CDSCB series (MHz Discriminator) enable customers to (1.28)(1.28) 0.3 min.0.3 min. make VICS/RKE/TPMS sets very thin and small. 0.65±0.30.7±0.3 0.65±0.3 0.3 (1): Input Features 0.85± ((16)) ((52)) ((43)) 3 ((23))((54)):: GNroo cuonndnection 1. The filters are mountable by automatic placers. 85±0.3 (1.28)(1.28) 0.75±0. ( ( 6 ))::: EROIeuAftJep rMuetnocnethly Code 0. 0 to 0.35 0 to 0.35 (in mm) 2. They are slim, at only 1.4mm max. thickness, and have a small mounting area (3.45x3.1mm) enabling flexible PCB design. 3. Various bandwidths are available. Select a suitable type in accordance with the desired characteristics. 4. Operating Temperature Range: -20 to +80°C (Standard Type) -40 to +85°C (High-reliability Type) Storage Temperature Range: -40 to +85°C (Standard Type) -55 to +85°C (High-reliability Type) Standard Type Center Nominal Center 3dB Attenuation Insertion Loss Ripple Spurious Spurious Input/Output Part Number Frequency Frequency (fn) Bandwidth Attenuation Attenuation Impedance (fo) (MHz) (MHz) (kHz) (kHz) (dB) (dB) (1) (dB) (2) (dB) (ohm) 10.700 30 min. 30 min. SFECF10M7HA00-R0 - 180 ±40kHz 470 max. 4.0±2.0dB 1.0 max. 330 ±30kHz [within 9MHz to fo] [within fo to 12MHz] 8.0max. 30 min. 25 min. SFECF10M7HF00-R0 - 10.700 fn±25 min. 510 max. 1.0 max. 330 [at fn] [within 9MHz to fn][within fn to 12MHz] 10.700 30 min. 30 min. SFECF10M7GA00-R0 - 230 ±50kHz 510 max. 3.5±2.0dB 1.0 max. 330 ±30kHz [within 9MHz to fo] [within fo to 12MHz] 8.0max. 30 min. 25 min. SFECF10M7GF00-R0 - 10.700 fn±45 min. 560 max. 1.0 max. 330 [at fn] [within 9MHz to fn][within fn to 12MHz] 10.700 30 min. 30 min. SFECF10M7FA00-R0 - 280 ±50kHz 590 max. 3.0±2.0dB 1.0 max. 330 ±30kHz [within 9MHz to fo] [within fo to 12MHz] 7.0max. 30 min. 25 min. SFECF10M7FF00-R0 - 10.700 fn±65 min. 620 max. 1.0 max. 330 [at fn] [within 9MHz to fn][within fn to 12MHz] 10.700 30 min. 30 min. SFECF10M7EA00-R0 - 330 ±50kHz 700 max. 3.0±2.0dB 1.0 max. 330 ±30kHz [within 9MHz to fo] [within fo to 12MHz] 10.700 35 min. 25 min. SFECF10M7DA0001-R0 - 420 min. 950 max. 3.0±2.0dB 3.0 max. 330 ±30kHz [within 9MHz to fo] [within fo to 12MHz] 6.0max. 20 min. 20 min. SFECF10M7DF00-R0 - 10.700 fn±150 min. 990 max. 3.0 max. 330 [at fn] [within 9MHz to fn][within fn to 12MHz] Area of Attenuation: [within 20dB] Area of Insertion Loss: at minimum loss point Area of Ripple: within 3dB B.W. Center frequency (fo) defined by the center of 3dB bandwidth. For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters. The order quantity should be an integral multiple of the "Minimum Quantity" shown in the packaging page. 6

!Note (cid:129) Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. P51E.pdf (cid:129) This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.10,2019 High-reliability Type Part Number FrCeqeunetenrcy NForemqiuneanl cCye (nftne)r Ban3ddwBidth Attenuation Insertion Loss Ripple AtStpeunruioautison AtStpeunruioautison InImpupte/dOauntcpeut 1 (fo) (MHz) (MHz) (kHz) (kHz) (dB) (dB) (1) (dB) (2) (dB) (ohm) 10.700 30 min. 30 min. SFECF10M7HA00S0-R0 - 180 ±40kHz 470 max. 4.0±2.0dB 1.0 max. 330 ±30kHz [within 9MHz to fo][within fo to 12MHz] 8.0max. 30 min. 25 min. SFECF10M7HF00S0-R0 - 10.700 fn±25 min. 510 max. 1.0 max. 330 [at fn] [within 9MHz to fn][within fn to 12MHz] 10.700 30 min. 30 min. SFECF10M7GA00S0-R0 - 230 ±50kHz 510 max. 3.5±2.0dB 1.0 max. 330 ±30kHz [within 9MHz to fo][within fo to 12MHz] 8.0max. 30 min. 25 min. SFECF10M7GF00S0-R0 - 10.700 fn±45 min. 560 max. 1.0 max. 330 [at fn] [within 9MHz to fn][within fn to 12MHz] 10.700 30 min. 30 min. SFECF10M7FA00S0-R0 - 280 ±50kHz 590 max. 3.0±2.0dB 1.0 max. 330 ±30kHz [within 9MHz to fo][within fo to 12MHz] 7.0max. 30 min. 25 min. SFECF10M7FF00S0-R0 - 10.700 fn±65 min. 630 max. 1.0 max. 330 [at fn] [within 9MHz to fn][within fn to 12MHz] 10.700 30 min. 30 min. SFECF10M7EA00S0-R0 - 330 ±50kHz 700 max. 3.0±2.0dB 1.0 max. 330 ±30kHz [within 9MHz to fo][within fo to 12MHz] 6.0max. 20 min. 20 min. SFECF10M7DF00S0-R0 - 10.700 fn±145 min. 990 max. 3.0 max. 330 [at fn] [within 9MHz to fn][within fn to 12MHz] Area of Attenuation: [within 20dB] Area of Insertion Loss: at minimum loss point Area of Ripple: within 3dB B.W. Center frequency (fo) defined by the center of 3dB bandwidth. For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters. The order quantity should be an integral multiple of the "Minimum Quantity" shown in the packaging page. Standard Center Frequency Rank Code CODE 30kHz Step 25kHz Step A 10.700MHz±30kHz 10.700MHz±25kHz Standard Land Pattern Dimensions Test Circuit 1 (3) (4) 3 0. (2) (5) 0. (6) (5) (4)0.1 1.05 R1 (1) (6) 3 0. 0 Rg 3 0.1 1.4 S.S.G. E1 R2 C2 E2 RVFoltmeter 0. 5 (1) (2) (3) 0 0.1 1. (1): Input 0.1 0.1 (1): Input ((23))((54)):: GNroo cuonndnection 0.8 0.6 0.8 0.6 0.8 ((23))((54)):: GNroo cuonndnection Rg=50Ω R1=280Ω±5% R2=330Ω±5% (6): Output (6): Output C2=10±2pF (Including stray capacitance and Input capacitance Indicates solder resist land pattern. (in mm) of RF voltmeter) E1: S.S.G. Output Voltage 7

!Note (cid:129) Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. P51E.pdf (cid:129) This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.10,2019 Frequency Characteristics Standard Type 1 SFECF10M7HA00-R0/SFECF10M7HF00-R0 SFECF10M7GA00-R0/SFECF10M7GF00-R0 0 7.0 0 7.0 1 6.0 1 6.0 2 5.0 ec.) 2 5.0 ec.) B) μ s B) μ s n (d 3 4.0 me ( n (d 3 4.0 me ( Attenuatio 54 32..00 oup Delay Ti Attenuatio 54 32..00 oup Delay Ti Gr Gr 6 1.0 6 1.0 7 0.0 7 0.0 10.300 10.500 10.700 10.900 11.100 10.300 10.500 10.700 10.900 11.100 Frequency (MHz) Frequency (MHz) SFECF10M7FA00-R0/SFECF10M7FF00-R0 SFECF10M7EA00-R0 0 7.0 0 7.0 1 6.0 1 6.0 2 5.0 ec.) 2 5.0 ec.) B) μ s B) μ s n (d 3 4.0 me ( n (d 3 4.0 me ( Attenuatio 54 32..00 oup Delay Ti Attenuatio 54 32..00 oup Delay Ti Gr Gr 6 1.0 6 1.0 7 0.0 7 0.0 10.300 10.500 10.700 10.900 11.100 10.300 10.500 10.700 10.900 11.100 Frequency (MHz) Frequency (MHz) SFECF10M7DA0001-R0 SFECF10M7DF00-R0 0 7.0 0 7.0 1 6.0 1 6.0 2 5.0 ec.) 2 5.0 ec.) B) μ s B) μ s n (d 3 4.0 me ( n (d 3 4.0 me ( Attenuatio 54 32..00 oup Delay Ti Attenuatio 54 32..00 oup Delay Ti Gr Gr 6 1.0 6 1.0 7 0.0 7 0.0 10.300 10.500 10.700 10.900 11.100 10.300 10.500 10.700 10.900 11.100 Frequency (MHz) Frequency (MHz) 8

!Note (cid:129) Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. P51E.pdf (cid:129) This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.10,2019 Frequency Characteristics High-reliability Type SFECF10M7HA00S0-R0/SFECF10M7HF00S0-R0 SFECF10M7GA00S0-R0/SFECF10M7GF00S0-R0 1 0 7.0 0 7.0 1 6.0 1 6.0 2 5.0ec.) 2 5.0ec.) B) μ s B) μ s n (d 3 4.0me ( n (d 3 4.0me ( Attenuatio 54 32..00oup Delay Ti Attenuatio 54 32..00oup Delay Ti Gr Gr 6 1.0 6 1.0 7 0.0 7 0.0 10.300 10.500 10.700 10.900 11.100 10.300 10.500 10.700 10.900 11.100 Frequency (MHz) Frequency (MHz) SFECF10M7FA00S0-R0/SFECF10M7FF00S0-R0 SFECF10M7EA00S0-R0 0 7.0 0 7.0 1 6.0 1 6.0 2 5.0ec.) 2 5.0ec.) B) μ s B) μ s n (d 3 4.0me ( n (d 3 4.0me ( Attenuatio 54 32..00oup Delay Ti Attenuatio 54 32..00oup Delay Ti Gr Gr 6 1.0 6 1.0 7 0.0 7 0.0 10.300 10.500 10.700 10.900 11.100 10.300 10.500 10.700 10.900 11.100 Frequency (MHz) Frequency (MHz) SFECF10M7DF00S0-R0 0 7.0 1 6.0 2 5.0ec.) B) μ s n (d 3 4.0me ( Attenuatio 54 32..00oup Delay Ti Gr 6 1.0 7 0.0 10.300 10.500 10.700 10.900 11.100 Frequency (MHz) 9

!Note (cid:129) Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. P51E.pdf (cid:129) This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.10,2019 Frequency Characteristics (Spurious) Standard Type 1 SFECF10M7HA00-R0/SFECF10M7HF00-R0 SFECF10M7GA00-R0/SFECF10M7GF00-R0 0 0 10 10 20 20 B) B) d d n ( 30 n ( 30 o o ati ati nu 40 nu 40 e e Att Att 50 50 60 60 70 70 8.700 9.700 10.700 11.700 12.700 8.700 9.700 10.700 11.700 12.700 Frequency (MHz) Frequency (MHz) SFECF10M7FA00-R0/SFECF10M7FF00-R0 SFECF10M7EA00-R0 0 0 10 10 20 20 B) B) d d n ( 30 n ( 30 o o ati ati nu 40 nu 40 e e Att Att 50 50 60 60 70 70 8.700 9.700 10.700 11.700 12.700 8.700 9.700 10.700 11.700 12.700 Frequency (MHz) Frequency (MHz) SFECF10M7DA0001-R0/SFECF10M7DF00-R0 0 10 20 B) d n ( 30 o ati nu 40 e Att 50 60 70 8.700 9.700 10.700 11.700 12.700 Frequency (MHz) 10

!Note (cid:129) Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. P51E.pdf (cid:129) This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.10,2019 Frequency Characteristics (Spurious) High-reliability Type SFECF10M7HA00S0-R0/SFECF10M7HF00S0-R0 SFECF10M7GA00S0-R0/SFECF10M7GF00S0-R0 1 0 0 10 10 20 20 B) B) d d n ( 30 n ( 30 o o ati ati nu 40 nu 40 e e Att Att 50 50 60 60 70 70 8.700 9.700 10.700 11.700 12.700 8.700 9.700 10.700 11.700 12.700 Frequency (MHz) Frequency (MHz) SFECF10M7FA00S0-R0/SFECF10M7FF00S0-R0 SFECF10M7EA00S0-R0 0 0 10 10 20 20 B) B) d d n ( 30 n ( 30 o o ati ati nu 40 nu 40 e e Att Att 50 50 60 60 70 70 8.700 9.700 10.700 11.700 12.700 8.700 9.700 10.700 11.700 12.700 Frequency (MHz) Frequency (MHz) SFECF10M7DF00S0-R0 0 10 20 B) d n ( 30 o ati nu 40 e Att 50 60 70 8.700 9.700 10.700 11.700 12.700 Frequency (MHz) 11

!Note (cid:129) Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. P51E.pdf (cid:129) This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.10,2019 Notice 1 Ceramic Filters (CERAFIL) Chip Type SFECF Series e Soldering and Mounting e 1. Standard Reflow Soldering Conditions (1) Reflow Filter is soldered twice within the following temperature Peak (260°C max.) conditions. C)260 e (°230 ur at Heating per Pre-heating (230°C) m (150-180°C) e100 T Gradual Cooling 30 sec. 60-120 sec. 40 sec. 120 sec. min. max. min. (2) Soldering Iron Filter is soldered at +350±5°C for 3.0±0.5 seconds. The soldering iron should not touch the filter while soldering. (3) Conditions for Placement Machines The component is recommended for use with placement machines that employ optical placement capabilities. The component might be damaged by excessive mechanical force. Please make sure that you have evaluated by using placement machines before going into mass production. Do not use placement machines that utilize mechanical positioning. Please contact Murata for details beforehand. (4) Other (a) The component may be damaged if excess [Component Direction] mechanical stress is applied to it mounted on the Place the printed circuit board. component (b) Design layout of components on the PC board to lateral to the direction in minimize the stress imposed on the warp or flexure of which stress the board. acts. (c) After installing components, if solder is excessively [Component Layout Close to Board] applied to the circuit board, mechanical stress will cause destruction resistance characteristics to Perforation B Susceptibility to degrade. To prevent this, be extremely careful in stress is in the order of: A>C>B determining shape and dimension before designing A Slit C the circuit board diagram. (d) When the positioning claws and pick-up nozzle are worn, the load is applied to the components while positioning is concentrated on positioning accuracy, etc. Careful checking and maintenance are necessary to prevent unexpected trouble. (e) When correcting components with a soldering iron, the tip of the soldering iron should not directly touch the component. Depending on the soldering conditions, the effective area of terminations may be reduced. Solder containing Ag should be used to prevent electrode erosion. (f) Do not use strong acidity flux, more than 0.2wt% chlorine content, in reflow soldering. Continued on the following page. 12

!Note (cid:129) Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. P51E.pdf (cid:129) This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.10,2019 Notice 1 Continued from the preceding page. 2. Wash Do not clean or wash the component as it is not hermetically sealed. 3. Coating In case of overcoating the component, conditions such as material of resin, cure temperature, and so on should be evaluated well. e Storage and Operating Conditions e 1. Product Storage Conditions (2) Please do not put the products directly on the floor Please store the products in a room where the without anything under them to avoid damp places temperature/humidity is stable, and avoid places where and/or dusty places. there are large temperature changes. Please store the (3) Please do not store the products in places such as a products under the following conditions: damp heated place or any place exposed to direct Temperature: -10 to +40°C sunlight or excessive vibration. Humidity: 15 to 85% R.H. (4) Please use the products immediately after package is 2. Expiration Date on Storage opened, because quality and solderability may be Expiration date (shelf life) of the products is six months degraded due to storage under poor conditions. after delivery under the conditions of a sealed and (5) To avoid cracking of the ceramic element, please do unopened package. Please use the products within six not drop the products. months after delivery. If you store the products for a long 4. Other time (more than six months), use carefully because Please be sure to consult with our sales representative or solderability may be degraded due to storage under poor engineer whenever the products are to be used in conditions. conditions not listed above. Please confirm solderability and characteristics for the products regularly. 3. Notice on Product Storage (1) Please do not store the products in a chemical atmosphere (Acids, Alkali, Bases, Organic gas, Sulfides and so on), because quality and solderability may be degraded due to storage in a chemical atmosphere. e Rating e The component may be damaged if excessive mechanical stress is applied. e Handling e 1. Accurate test circuit values are required to measure electrical characteristics. Miscorrelation may be caused if there is any deviation, especially stray capacitance, from the test circuit in the specification. 2. The components, packed in a moisture proof bag (dry pack), are sensitive to moisture. The following treatment is required before applying reflow soldering, to avoid reliability degradation caused by thermal stress. When unpacked, store the component in an atmosphere of reflow 30°C and below 60%R.H., and solder within 1 week. 13

!Note (cid:129) Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. P51E.pdf (cid:129) This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.10,2019 Packaging 1 Minimum Quantity/Dimensions of Reel Embossed Tape ø180mm 2,000 (pcs.) Dimensions of Reel Trailer Leader 160 to 190 Cover film Empty Components Empty 240 to 280 ø13.0±0.5 400 to 560 +1.060-0+0180-1.5 2.0±0.5 17.0±1.0 13.0+-01.0 (in mm) Dimensions of Carrier Tape Dimensions of Carrier Tape 1 4.0±0.1 0. ± 5 ø1.55±0.05 2.0±0.05 7 Chip filter 1. x. a m 4.1±0.1 5.5±0.05 12.0±0.2 3° 1 0. CP(o0ev.1eelr it nfiogl m0 s.t7rNen)gth 10° max. 4.0±0.1 (33°.3)5+-00..015 0.3±0.05 (0.05) 1.84±0.1 4.1± User direction of feed (cid:70)(cid:3)(cid:20)(cid:31)(cid:48)(cid:50)(cid:3)(cid:44)(cid:51)(cid:43)(cid:32)(cid:35)(cid:48)(cid:3)(cid:43)(cid:31)(cid:48)(cid:41)(cid:35)(cid:34)(cid:3)(cid:49)(cid:39)(cid:34)(cid:35)(cid:3)(cid:39)(cid:49)(cid:3)(cid:31)(cid:42)(cid:53)(cid:31)(cid:55)(cid:49)(cid:3)(cid:36)(cid:31)(cid:33)(cid:39)(cid:44)(cid:37)(cid:3)(cid:51)(cid:46)(cid:64) ( ): Reference (in mm) 14

!Note (cid:129) Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. P51E.pdf (cid:129) This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.10,2019 Ceramic Filters (CERAFIL) RoHS Chip Type SFECV/SFECK Series 6.9±0.3 The SFECV/SFECK10M7 series for FM receivers are 4.05±0.4 1.2±0.5 1.2±0.3 1.2±0.5 1.5±0.2 monolithic type ceramic filters that utilize the thickness expander mode of piezoelectric ceramics. The SFECV series 2 3 enable customers to make an AM/FM set very thin, and it 2.9±0. ** * can be useful to the total chip circuit. (3) (2) (1) Features 2 0. : Marking 1. The piezoelectric element is sandwiched by heat resistant 1.5± (1) : Input (2) : Ground substrate, thus it has excellent mechanical strength, and 1.0±0.5 1.0±0.5 1.0±0.5 (3) : Output it is suitable for automatic mounting. ** : EIAJ Monthly Code ** : Center Frequency Rank Code (in mm) 2. Various bandwidths are available. Select a suitable type in accordance with the desired characteristics. 3. Operating Temperature Range: -20 to +80°C (Standard Type) -40 to +85°C (High-reliability Type) Storage Temperature Range: -40 to +85°C (Standard Type) -55 to +85°C (High-reliability Type) Applications 1. Small, thin radios 2. Automotive radios 3. Headphone stereos Standard Type Center 3dB Attenuation Insertion Loss Ripple Spurious Spurious Input/Output Part Number Frequency Bandwidth Attenuation Attenuation Impedance (fo) (MHz) (kHz) (kHz) (dB) (dB) (1) (dB) (2) (dB) (ohm) 15.000 30 min. 30 min. SFECV15M0EQ0001-R0 300 min. 750 max. 7.0max. 1.0 max. 330 ±50kHz [within 14MHz to fo][within fo to 16MHz] 10.700 35 min. 35 min. SFECV10M7KA00-R0 110 ±30kHz 320 max. 6.0±2.0dB 1.0 max. 330 ±30kHz [within 9MHz to fo] [within fo to 12MHz] 10.700 35 min. 35 min. SFECV10M7JA00-R0 150 ±40kHz 380 max. 5.5±2.0dB 1.0 max. 330 ±30kHz [within 9MHz to fo] [within fo to 12MHz] Area of Attenuation: [within 20dB] Area of Insertion Loss: at minimum loss point Center frequency (fo) defined by the center of 3dB bandwidth. For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters. The order quantity should be an integral multiple of the "Minimum Quantity" shown in the packaging page. High-reliability Type Center 3dB Attenuation Insertion Loss Ripple Spurious Spurious Input/Output Part Number Frequency Bandwidth Attenuation Attenuation Impedance (fo) (MHz) (kHz) (kHz) (dB) (dB) (1) (dB) (2) (dB) (ohm) 10.700 35 min. 35 min. SFECK10M7KA00S0-R0 110 ±30kHz 320 max. 6.0±2.0dB 1.0 max. 330 ±30kHz [within 9MHz to fo][within fo to 12MHz] 10.700 35 min. 35 min. SFECK10M7JA00S0-R0 150 ±40kHz 380 max. 5.5±2.0dB 1.0 max. 330 ±30kHz [within 9MHz to fo][within fo to 12MHz] Area of Attenuation: [within 20dB] Area of Insertion Loss: at minimum loss point Center frequency (fo) defined by the center of 3dB bandwidth. For safety purposes, connect the output of filters to the IF amplifier through a D.C. blocking capacitor. Avoid applying a direct current to the output of ceramic filters. The order quantity should be an integral multiple of the "Minimum Quantity" shown in the packaging page. 15

!Note (cid:129) Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. P51E.pdf (cid:129) This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.10,2019 Standard Center Frequency Rank Code CODE 30kHz Step 25kHz Step A 10.700MHz±30kHz 10.700MHz±25kHz Standard Land Pattern Dimensions Test Circuit 1.2 1.2 1.2 2 R1 (1) (3) Rg (2) 4.0 E1 R2 C2 E2 RVFoltmeter S.S.G. =-10dBm (1): Input 1.65 1.65 (2): Ground 2.85 2.85 (3): Output Rg=50Ω R1=280Ω±5% R2=330Ω±5% C2=10±2pF (Including stray capacitance and Input capacitance of RF voltmeter) Land (in mm) E1: S.S.G. Output Voltage Frequency Characteristics Standard Type SFECV15M0EQ0001-R0 SFECV10M7KA00-R0 0 10.0 0 7.0 1 6.5 2 8.0 ec.) 2 6.0 ec.) B) μ s B) μ s n (d 4 6.0 me ( n (d 3 5.5 me ( Attenuatio 6 4.0 oup Delay Ti Attenuatio 54 45..50 oup Delay Ti Gr Gr 8 2.0 6 4.0 10 0.0 7 3.5 14.700 14.800 14.900 15.000 15.100 15.200 15.300 10.300 10.500 10.700 10.900 11.100 Frequency (MHz) Frequency (MHz) SFECV10M7JA00-R0 0 8.0 1 7.5 2 7.0 ec.) B) μ s n (d 3 6.5 me ( Attenuatio 54 65..05 oup Delay Ti Gr 6 5.0 7 4.5 10.300 10.500 10.700 10.900 11.100 Frequency (MHz) 16

!Note (cid:129) Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. P51E.pdf (cid:129) This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.10,2019 Frequency Characteristics High-reliability Type SFECK10M7KA00S0-R0 SFECK10M7JA00S0-R0 0 7.0 0 8.0 1 6.5 1 7.5 2 6.0ec.) 2 7.0ec.) B) μ s B) μ s n (d 3 5.5me ( n (d 3 6.5me ( Attenuatio 54 45..50oup Delay Ti Attenuatio 54 65..05oup Delay Ti 2 Gr Gr 6 4.0 6 5.0 7 3.5 7 4.5 10.300 10.500 10.700 10.900 11.100 10.300 10.500 10.700 10.900 11.100 Frequency (MHz) Frequency (MHz) Frequency Characteristics (Spurious) Standard Type SFECV15M0EQ0001-R0 SFECV10M7KA00-R0 0 0 10 10 20 20 dB) 30 dB) n ( n ( 30 atio 40 atio nu nu 40 Atte 50 Atte 50 60 70 60 80 70 13.000 14.000 15.000 16.000 17.000 8.700 9.700 10.700 11.700 12.700 Frequency (MHz) Frequency (MHz) SFECV10M7JA00-R0 0 10 20 B) d n ( 30 o ati nu 40 e Att 50 60 70 8.700 9.700 10.700 11.700 12.700 Frequency (MHz) Frequency Characteristics (Spurious) High-reliability Type SFECK10M7KA00S0-R0 SFECK10M7JA00S0-R0 0 0 10 10 20 20 B) B) d d n ( 30 n ( 30 o o ati ati nu 40 nu 40 e e Att Att 50 50 60 60 70 70 8.700 9.700 10.700 11.700 12.700 8.700 9.700 10.700 11.700 12.700 Frequency (MHz) Frequency (MHz) 17

!Note (cid:129) Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. P51E.pdf (cid:129) This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.10,2019 Notice Ceramic Filters (CERAFIL) Chip Type SFECV/SFECK Series e Soldering and Mounting e 1. Standard Reflow Soldering Conditions (1) Reflow Filter is soldered twice within the following temperature Peak 2 conditions. C)240 (240°C max.) e (°230 ur at Heating per Pre-heating (230°C) m (150-180°C) e100 T Gradual Cooling 30 sec. 60-120 sec. 30 sec. 120 sec. min. max. min. (2) Soldering Iron Filter is soldered at +350±5°C for 3.0±0.5 seconds. The soldering iron should not touch the filter while soldering. (3) Conditions for Placement Machines The component is recommended for use with placement machines that employ optical placement capabilities. Damage may result from excessive mechanical force. Please make sure that you have evaluated by using placement machines before going into mass production. Do not use placement machines that utilize mechanical positioning. Please contact Murata for details beforehand. (4) Other (a) The component may be damaged if excess [Component Direction] mechanical stress is applied to it mounted on the Put the printed circuit board. component (b) Design layout of components on the PC board to lateral to the direction in minimize the stress imposed on the warp or flexure of which stress the board. acts. (c) After installing components, if solder is excessively [Component Layout Close to Board] applied to the circuit board, mechanical stress will cause destruction resistance characteristics to Perforation B Susceptibility to degrade. To prevent this, be extremely careful in stress is in the order of: A>C>B determining shape and dimension before designing A Slit C the circuit board diagram. (d) When the positioning claws and pick-up nozzle are worn, the load is applied to the components while positioning is concentrated to one positioning accuracy, etc. Careful checking and maintenance are necessary to prevent unexpected trouble. (e) When correcting components with a soldering iron, the tip of the soldering iron should not directly touch the component. Depending on the soldering conditions, the effective area of terminations may be reduced. Solder containing Ag should be used to prevent electrode erosion. (f) Do not use strong acidity flux, more than 0.2wt% chlorine content, in reflow soldering. Continued on the following page. 18

!Note (cid:129) Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. P51E.pdf (cid:129) This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.10,2019 Notice Continued from the preceding page. 2. Wash Do not clean or wash the component as it is not hermetically sealed. 3. Coating In case of overcoating the component, conditions such as 2 material of resin, cure temperature, and so on should be evaluated well. e Storage and Operating Conditions e 1. Product Storage Conditions (2) Please do not put the products directly on the floor Please store the products in room where the without anything under them to avoid damp places temperature/humidity is stable, and avoid places where and/or dusty places. there are large temperature changes. Please store the (3) Please do not store the products in the places such as products under the following conditions: a damp heated place or any place exposed to direct Temperature: -10 to +40°C sunlight or excessive vibration. Humidity: 15 to 85% R.H. (4) Please use the products immediately after package is 2. Expiration Date on Storage opened, because quality and solderability may be Expiration date (Shelf life) of the products is six months degraded due to storage under the poor conditions. after delivery under the conditions of a sealed and (5) To avoid cracking of the ceramic element, please do unopened package. Please use the products within six not drop the products. months after delivery. If you store the products for a long 4. Other time (more than six months), use carefully because the Please be sure to consult with our sales representative or products may be degraded in solderability due to storage engineer whenever the products are to be used in under poor conditions. conditions not listed above. Please confirm solderability and characteristics for the products regularly. 3. Notice on Product Storage (1) Please do not store the products in a chemical atmosphere (Acids, Alkali, Bases, Organic gas, Sulfides and so on), because quality and solderability may be degraded due to the storage in a chemical atmosphere. e Rating e The component may be damaged if excessive mechanical stress is applied. e Handling e Accurate test circuit values are required to measure electrical characteristics. Miscorrelation may be caused if there is any deviation, especially stray capacitance, from the test circuit in the specification. 19

!Note (cid:129) Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. P51E.pdf (cid:129) This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.10,2019 Packaging Minimum Quantity/Dimensions of Reel Embossed Tape ø180mm 2,000 (pcs.) 2 Dimensions of Reel Trailer Leader 160-190 Cover film Empty Components Empty 240-280 ø13.0±0.5 400-560 +1.060–0 +0180–1.5 2.0±0.5 13.0+–10.0 17.0±1.0 (in mm) Dimensions of Carrier Tape (cid:8)(cid:39)(cid:43)(cid:35)(cid:44)(cid:49)(cid:39)(cid:45)(cid:44)(cid:49)(cid:3)(cid:45)(cid:36)(cid:3)(cid:7)(cid:31)(cid:48)(cid:48)(cid:39)(cid:35)(cid:48)(cid:3)(cid:24)(cid:31)(cid:46)(cid:35) 1 0. ø1.5+–00..10 2.0±0.05 4.0±0.1 75± 1. 5 0 * * * * * 0.01 5.5±0. 0±0.2 ** ** ** ** ** 7.3± 12. PCeoevlienrg fi sltmrengt1h0 0°. 1m taox 40...07±N0.1 3.0±0.1 (3(cid:7)°(cid:38))(cid:39)(cid:46)(cid:3)(cid:113)(cid:42)(cid:50)(cid:35)(cid:48) 0.3±0.05+0.11.7–0.05 1.9±0.1 (cid:25)(cid:49)(cid:35)(cid:48)(cid:3)(cid:34)(cid:39)(cid:48)(cid:35)(cid:33)(cid:50)(cid:39)(cid:45)(cid:44)(cid:3)(cid:45)(cid:36)(cid:3)(cid:36)(cid:35)(cid:35)(cid:34) (cid:70)(cid:3)(cid:20)(cid:31)(cid:48)(cid:50)(cid:3)(cid:44)(cid:51)(cid:43)(cid:32)(cid:35)(cid:48)(cid:3)(cid:43)(cid:31)(cid:48)(cid:41)(cid:35)(cid:34)(cid:3)(cid:49)(cid:39)(cid:34)(cid:35)(cid:3)(cid:39)(cid:49)(cid:3)(cid:31)(cid:42)(cid:53)(cid:31)(cid:55)(cid:49)(cid:3)(cid:36)(cid:31)(cid:33)(cid:39)(cid:44)(cid:37)(cid:3)(cid:51)(cid:46)(cid:64) ( ) : Reference (in mm) 20

!Note (cid:129) Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. P51E.pdf (cid:129) This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.10,2019 Ceramic Discriminator (CERAFIL) RoHS Chip Type CDSCB Series 2 0. The CDSCB10M7 series forms a resonator on a piezoelectric 3± 4.5±0.1 0. coebrtaaminisc s stuabbsletr daetem. Iond cuolamtiboinn acthioanra wctitehri sICtisc,s t hinis a t wypidee 2.0±0.1 1.4 max. bandwidth. 0.2±0.2 0.4±0.05 4.1 max. They have 1.0mm max. thickness and small mounting area max. (4.5x2.0mm). 1.0 0.4(ref.) 0.4(ref.) 0.8±0.1 0.8±0.1 Features 1. Compact and high reliability and recommended for 3 automotive applications. 1.5±0.1 1.5±0.1 (in mm) 2. Can be combined with various ICs. The IC is determined by the last number in the part number. 3. Stable demodulation characteristics can be obtained without adjustment. 4. Stable temperature characteristics. 5. Available lead (Pb) free solder reflow. Center Recovered Recovered Distortion S Curve Part Number Frequency (fo) Audio 3dB BW Audio Output IC (MHz) (kHz) (mV) (%) (mV) CDSCB10M7GA105A-R0 10.700 ±30kHz 220 min. 110 min. 1.5 max. - TEA5757HL CDSCB10M7GA113-R0 10.700 ±30kHz 300 min. 110 min. 1.0 max. - TA2154FN CDSCB10M7GA119-R0 10.700 ±30kHz 500 min. 75 min. 1.0 max. - TRF6901 CDSCB10M7GA121-R0 10.700 ±30kHz 390 min. 80 min. 1.0 max. - LV23100V CDSCB10M7GA135-R0 10.700 ±30kHz 155 min. 75 min. - - TH71101 CDSCB10M7GA136-R0 10.700 ±30kHz 140 min. 120 min. - - TH7122 CDSCB10M7GF072-R0 10.700 (fn) fn±150 min. 130 min. 2.0 max. - TA31161 CDSCB10M7GF107S-R0 10.700 (fn) fn±80 min. 52 min. 3.0 max. - TA31272FN CDSCB10M7GF109-R0 10.700 (fn) fn±100 min. 170 min. 3.0 max. - TK14588V CDSCB10M7GF123-R0 10.700 (fn) - - - 900 min. TA31275FN CDSCB10M7GF123S-R0 10.700 (fn) - - - 900 min. TA31275FN CDSCB10M7GF126-R0 10.700 (fn) - - - 400 min. NJM2295AV (fn) indicates nominal center frequency (10.700MHz). For safety purposes, avoid applying a direct current between the terminals. The order quantity should be an integral multiple of the "Minimum Quantity" shown in the packaging page. Standard Center Frequency Rank Code CODE 30kHz Step 25kHz Step A 10.700MHz±30kHz 10.700MHz±25kHz 21

!Note (cid:129) Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. P51E.pdf (cid:129) This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.10,2019 Standard Land Pattern Dimensions 3.0 6 2. 1.0 2.0 1.0 (in mm) Test Circuit 3 CDSCB10M7GA105A-R0 CDSCB10M7GA113-R0 Vcc (1.2V) Vcc (3.0V) 0.1μ μ μ 10μ 1 1 + μ 0 0 48 47 46 45 44 43 42 41 40 39 38 37 0.1μ 01 0. 0. + 1 36 0. 100μ 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 2 35 S.S.G. TA2154FN (TOSHIBA) 3 34 4 33 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 + 5 32 X p 2.2μ 6 TEA5757HL 31 80 7 (PHILIPS) 30 μ μ 6 8 29 01 01 D.C. OUT AF OUT 9 28 0. 0. 100k X: CDSCB10M7GA113-R0 10 27 S.S.G. Unit C: F 11 26 10 R: Ω DC OUT 12 25 13 14 15 16 17 18 19 20 21 22 23 24 + μ μ 330p 4.7μ 1 1 7μ 0. 0. 4 X 0. 0.22μ 150 n) p) C ( C ( AF OUT F F A A X: CDSCB10M7GA105A-R0 Unit C: F R: Ω CDSCB10M7GA119-R0 CDSCB10M7GA121-R0 Vcc (3.0V) AF Output 0.01μ D.C. Output Vcc (3.2V) IF Input AF Output 68p 0.01μ 0.01μ 15p 220k 22μ+ 0.015μ 10p 10p 120p 10 82p 36 35 34 33 32 31L3V0223910208V2 (7SA26NY2O5)24 23 22 21 20 19 4.7μ 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 10k 0.01μ0.01μ148474645444342414039383736 X 10μ + 0.047μ μ 23 33541000p 7μ 1+ X 4 33 4 56 TRF6901 3321 47p 0.0 0.47+μ 78 (TEXAS INSTRUMENTS)32090.01μ 0k 3.3k 1 9 28 100p10 27 + 11 26 1μ 12 25 μ 0.01μ13141516171819202122+230.2242μ 0.1μ S.G. 75 0.047 100μ + 100p 10k 0.47μ 100p 10k 18 17 16 15 14 13 12 11 10 181716151413121110 PIC16F84 (Control IC) PIC16F84 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 1k 1k 10k Unit C: F 2.2μ + 10k 0.1μ Unit + R: Ω C: F X: CDSCB10M7GA119-R0 2.2μ 0.1μ L: H X: CDSCB10M7GA121-R0 R: Ω Continued on the following page. 22

!Note (cid:129) Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. P51E.pdf (cid:129) This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.10,2019 Continued from the preceding page. Test Circuit CDSCB10M7GA135-R0 CDSCB10M7GA136-R0 Vcc (5.0V) Vcc (5.0V) AF-OUT FKS-OUT 330p 0.1μ 0.1μ 24 23 22 21 20 19 18 17 25 16 26 15 0.01μ 100p 1000p0.01μ 27 14 330k 28 TH7122 13 330p 220k 29[Inter(nMalE ALFECX EISna)bled]12 30 11 0.01μ 24 23 22 21 20 19 18 17 31 10 0.01μ 2256 1156 12p C.D. 0.01μ321 2 30.14μ5 6 738390pFKS-OUT 0.01μ AF-OUT 27 14 1000p 28 TH71101, TH71102, 13 330p 100k TH71111 or TH71112 0.033μ 29 12 330p0.01μ 30 (MELEXIS) 11 0.011μ000p S.G. C.D. 3.3k 31 10 330p 0.01μ 321 2 3 4 5 6 7 8 9 100k 100p 3 18 17 16 15 14 13 12 11 10 0.01μ S.G. PIC16F84 (Control IC) 1 2 3 4 5 6 7 8 9 +10μ 33X0: CpDSCB10M7GAU1n3it5 CR-R:: FΩ0 1k +2.2μ10k 0.X1:μ CDSCB10M7UGnAi1t 3CR6-:: RFΩ0 CDSCB10M7GF072-R0 CDSCB10M7GF109-R0 Vcc (3V) 0.01μ Vcc (3.0V) 4.7μ μ 2 1. R AF OUT 0.01μ R X X 10p 0.01μ D.C. Output AF Output 16 15 14 13 12 11 10 9 1000p 0.01μ TA31161 (TOSHIBA) 12k 8p 1 2 3 4 5 6 7 8 51k 0.01μ 01μ 01μ 0. + 0. 33μ 0.01μ 16 15 14 13 12 11 10 9 IF IN Unit C: F X: CDSCB10M7GF072-R0 R: Ω TK14588V (TOKO) R: 820 L: H 1 2 3 4 5 6 7 8 μ μ μ 1 1 1 0 0 0 0. 0. 0. S.S.G. 51 + 4.7μ 0.01μ Unit C: F X: CDSCB10M7GF109-R0 R: Ω R: 820 L: H CDSCB10M7GF123-R0 CDSCB10M7GF126-R0 Vcc (5.0V) Vcc (5.0V) 1μ AF OUT 10μ + DC-OUT 3300p 0.0 D1000pC-OUT 0.01μ 0.01μ 200.01μ19 18 17 16 15100p14 13 12 11 0.01μ 24 23 22 21 20 19 18 17 16 15 14 13 NJM2295AV (JRC) TA31275FN (TOSHIBA) 1 2 3 4 5 6 7 8 9 10 0.01μ1 2 3 4 5 60.1μ7 8 9 101.8k11 12 0.01μ 10μ+ C.8Dp. 180 0.1μ 0.1μ 0.01μ 0.1μ 10μ+ 0.01μ 10μ+ S.S.G. X: CDSCB10M7GF123-R0 S.G. X: CDSCB10M7GF126-R0 Unit C: F Unit C: F R: Ω R: Ω 23

!Note (cid:129) Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. P51E.pdf (cid:129) This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.10,2019 Recovered Audio Curve CDSCB10M7GA105A-R0 CDSCB10M7GA113-R0 1000 100 1000 100 AF Output %) AF Output %) V) 100 10 n ( V) 100 10 n ( m o m o age ( Distortion storti age ( storti ut Volt 10 1 onic Di ut Volt 10 Distortion 1 onic Di p m p m Out Har Out Har AF 1 Input=100dBμ 0.1 otal AF 1 Input=100dBμ 0.1 otal fdev.=±75kHz T fdev.=±75kHz T fmod.=1kHz fmod.=1kHz Vcc=3.0V Vcc=1.2V 10.3 10.4 10.5 10.6 10.7 10.8 10.9 11.0 11.1 10.3 10.4 10.5 10.6 10.7 10.8 10.9 11.0 11.1 Frequency (MHz) Frequency (MHz) 3 CDSCB10M7GA119-R0 CDSCB10M7GA121-R0 1000 100 1000 100 AF Output %) AF Output %) V) 100 10 n ( V) 100 10 n ( m o m o age ( storti age ( storti ut Volt 10 Distortion 1 onic Di ut Volt 10 Distortion 1 onic Di p m p m Out Har Out Har AF 1 Input=100dBμ 0.1 otal AF 1 Input=100dBμ 0.1 otal fdev.=±60kHz T fdev.=±75kHz T fmod.=1kHz fmod.=1kHz Vcc=3.0V Vcc=3.2V 10.3 10.4 10.5 10.6 10.7 10.8 10.9 11.0 11.1 10.3 10.4 10.5 10.6 10.7 10.8 10.9 11.0 11.1 Frequency (MHz) Frequency (MHz) CDSCB10M7GA135-R0 CDSCB10M7GA136-R0 1000 1000 V) 100 V) 100 m m e ( e ( g g a a Volt 10 Volt 10 ut ut p p ut ut O O AF 1 Input=100dBμ AF 1 Input=100dBμ fdev.=±50kHz fdev.=±50kHz fmod.=1kHz fmod.=1kHz Vcc=5.0V Vcc=5.0V 0.1 0.1 10.4 10.5 10.6 10.7 10.8 10.9 11.0 10.4 10.5 10.6 10.7 10.8 10.9 11.0 Frequency (MHz) Frequency (MHz) Continued on the following page. 24

!Note (cid:129) Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. P51E.pdf (cid:129) This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.10,2019 Continued from the preceding page. Recovered Audio Curve CDSCB10M7GF072-R0 CDSCB10M7GF109-R0 1000 100 1000 100 %) %) V) 100 10 n ( V) 100 10 n ( m o m o age ( storti age ( storti ut Volt 10 1 onic Di ut Volt 10 1 onic Di p m p m Out Har Out Har AF 1 Input=100dBμ 0.1 otal AF 1 Input=100dBμ 0.1 otal fdev.=±80kHz T fdev.=±64kHz T fmod.=1kHz fmod.=1kHz Vcc=3.0V Vcc=3.0V 10.3 10.4 10.5 10.6 10.7 10.8 10.9 11.0 11.1 10.3 10.4 10.5 10.6 10.7 10.8 10.9 11.0 11.1 Frequency (MHz) Frequency (MHz) 3 S Curve CDSCB10M7GF123-R0 CDSCB10M7GF126-R0 2.5 4.0 2.0 3.0 1.5 V) V) olt ( olt ( V V 1.0 2.0 0.5 0.0 1.0 10.3 10.4 10.5 10.6 10.7 10.8 10.9 11.0 11.1 10.3 10.4 10.5 10.6 10.7 10.8 10.9 11.0 11.1 Frequency (MHz) Frequency (MHz) 25

!Note (cid:129) Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. P51E.pdf (cid:129) This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.10,2019 Notice Ceramic Discriminator (CERAFIL) Chip Type CDSCB Series e Soldering and Mounting e 1. Standard Reflow Soldering Conditions (1) Reflow Filter is soldered twice within the following temperature Peak (260°C max.) conditions. C)260 e (°230 ur at Heating per Pre-heating (230°C) m (150-180°C) e100 T Gradual Cooling 3 30 sec. 60-120 sec. 40 sec. 120 sec. min. max. min. (2) Soldering Iron Filter is soldered at +300±5°C for 3.0±0.5 seconds. The soldering iron should not touch the filter while soldering. (3) Conditions for Placement Machines The component is recommended for use with placement machines that employ optical placement capabilities. The component might be damaged by excessive mechanical force. Please make sure that you have evaluated by using placement machines before going into mass production. Do not use placement machines that utilize mechanical positioning. Please contact Murata for details beforehand. (4) Other (a) The component may be damaged if excess [Component Direction] mechanical stress is applied to it mounted on the Place the printed circuit board. component (b) Design layout of components on the PC board to laterally to the direction in minimize the stress imposed on the warp or flexure of which stress the board. acts. (c) After installing components, if solder is excessively [Component Layout Close to Board] applied to the circuit board, mechanical stress will cause destruction resistance characteristics to Perforation B Susceptibility to degrade. To prevent this, be extremely careful in stress is in the order determining shape and dimension before designing A Slit C of: A>C>B the circuit board diagram. (d) When the positioning claws and pick-up nozzle are worn, the load is applied to the components while positioning is concentrated on positioning accuracy, etc. Careful checking and maintenance are necessary to prevent unexpected trouble. (e) When correcting components with a soldering iron, the tip of the soldering iron should not directly touch the component. Depending on the soldering conditions, the effective area of terminations may be reduced. Solder containing Ag should be used to prevent electrode erosion. Continued on the following page. 26

!Note (cid:129) Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. P51E.pdf (cid:129) This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.10,2019 Notice Continued from the preceding page. 2. Wash Do not clean or wash the component as it is not hermetically sealed. 3. Coating In case of overcoating the component, conditions such as material of resin, cure temperature, and so on should be evaluated well. e Storage and Operating Conditions e 1. Product Storage Conditions without anything under them to avoid damp places Please store the products in a room where the and/or dusty places. 3 temperature/humidity is stable, and avoid places where (3) Please do not store the products in places such as a there are large temperature changes. Please store the damp heated place or any place exposed to direct products under the following conditions: sunlight or excessive vibration. Temperature: -10 to +40°C (4) Please use the products immediately after package is Humidity: 15 to 85% R.H. opened, because quality and solderability may be 2. Expiration Date on Storage degraded due to storage under poor conditions. Expiration date (shelf life) of the products is six months (5) To avoid cracking of the ceramic element, please do after delivery under the conditions of a sealed and not drop the products. unopened package. Please use the products within six 4. Other months after delivery. If you store the products for a long Please be sure to consult with our sales representative or time (more than six months), use carefully because engineer whenever the products are to be used in solderability may be degraded due to storage under poor conditions not listed above. conditions. Please confirm solderability and characteristics for the products regularly. 3. Notice on Product Storage (1) Please do not store the products in a chemical atmosphere (Acids, Alkali, Bases, Organic gas, Sulfides and so on), because quality and solderability may be degraded due to storage in a chemical atmosphere. (2) Please do not put the products directly on the floor e Rating e The component may be damaged if excessive mechanical stress is applied. e Handling e Accurate test circuit values are required to measure electrical characteristics. Miscorrelation may be caused if there is any deviation, especially stray capacitance, from the test circuit in the specification. 27

!Note (cid:129) Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. P51E.pdf (cid:129) This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.10,2019 Packaging Minimum Quantity/Dimensions of Reel Embossed Tape ø180mm 2,000 (pcs.) Dimensions of Reel Trailer Leader 160 to 190 Cover film Empty Components Empty 240 to 280 ø13.0±0.2 400 to 560 3 +0.160-0 +0.1180-1.5 2.0±0.5 +1.0 13.0-0 17.0±1.0 (in mm) Dimensions of Carrier Tape (cid:8)(cid:39)(cid:43)(cid:35)(cid:44)(cid:49)(cid:39)(cid:45)(cid:44)(cid:49)(cid:3)(cid:45)(cid:36)(cid:3)(cid:7)(cid:31)(cid:48)(cid:48)(cid:39)(cid:35)(cid:48)(cid:3)(cid:24)(cid:31)(cid:46)(cid:35) 1 4.0±0.12.0±0.05 ø1.5+0-.10 75±0. 1. 5 (9.0) 4.7±0.1 5.5±0.0 12.0±0.2 (cid:20)0.(cid:35)1(cid:35) t(cid:42)(cid:39)o(cid:44) (cid:37)0(cid:3).(cid:49)7(cid:50)N(cid:48)(cid:35)(cid:44)(cid:37)(cid:50)(cid:38)(cid:3) 4.0±01.10° Cøo1v.5e+r 0fi-.10lm2.2±0.1 (3°) 0.3±0.05 1.1±0.1 (cid:123)(cid:64)(cid:129)(cid:3)(cid:43)(cid:31)(cid:54)(cid:64)(cid:74) (cid:72) User direction of feed (cid:70)(cid:3)(cid:20)(cid:31)(cid:48)(cid:50)(cid:3)(cid:44)(cid:51)(cid:43)(cid:32)(cid:35)(cid:48)(cid:3)(cid:43)(cid:31)(cid:48)(cid:41)(cid:35)(cid:34)(cid:3)(cid:49)(cid:39)(cid:34)(cid:35)(cid:3)(cid:39)(cid:49)(cid:3)(cid:31)(cid:42)(cid:53)(cid:31)(cid:55)(cid:49)(cid:3)(cid:36)(cid:31)(cid:33)(cid:39)(cid:44)(cid:37)(cid:3)(cid:51)(cid:46)(cid:64) ( ): Reference (in mm) 28

!Note (cid:129) Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. P51E.pdf (cid:129) This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.10,2019 Crystal Filters Lead RoHS free Chip Type XDCAF/XDCAG/XDCAH/XDCBA Series 7.0±0.2 Murata's Crystal Filter with original thin wafer design (6) technology based on long experience and activity realizes (1) (5) 2 high reliability and is widely used in various applications such 0±0. 5. as business radios. (2) (4)5 1 0. (3) 1± 1. Features Pin Connection 1.2 (1): IN (2): GND 1. Low profile surface mount (3) (3): GND 2. Customized design and matching service (2) (4)1.0 ((45)):: OGUNTD 3. 4-Pole type is a small size in one package XDCAF 2.54 (6): GMNaDrking (1) (5) (6) (in mm) Applications 1. Radio communication 7.0±0.2 2. Base Station (6) 3. Communication (IF) other (1) (5) 2 0±0. 4 5. (2) (4)5 1 0. (3) 1± 1. Pin Connection 1.2 (1): IN (2): GND (3) (3): Coupling CAP (2) (4)1.0 ((45)):: OGUNTD XDCAG 54 (6): Coupling CAP 2. Marking (1) (5) (6) (in mm) 3.80 0.05 7.0±0.2 (8) 27± (6) (1) (7) 1. (1) (5) 2 3.80 (2) (6) 5.0±0. (3) (4) (5)0.30±0.201.00±0.20 27±0.05 (2) (3) (4)1.1±0.15 1. Pin Connection 7-1.00 P(1in): CINoPnUneTction 1.2 ((12)):: IGNND XDCBA 8-0.60 ((32)) (4) ((56)) ((((((234567)))))):::::: GGGOGGUNNNNNTDDDDDPUT XDCAH 2.54(2) (3) (4)1.0 ((((3456)))):::: COGCMooUNauuTDrppklliiinnnggg CCAAPP (1) (7) (8): GND (1) (5) Marking (8) (in mm) (6) (in mm) Series Center Frequency Number Series Size (MHz) of Poles XDCAF 2 XDCAG 7050 20 to 150 4 XDCAH 4 XDCBA 3838 45 to 150 2 29

!Note (cid:129) Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. P51E.pdf (cid:129) This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.10,2019 Part Number List XDCAF/XDCAG/XDCAH 7050 Size (11PN) Center Overtone Number 3dB Stop Band Guaranteed Spurious (dB min.) Insertion Ripple Operating Part Number Frequency Bandwidth Width Attenuation Loss Temperature (MHz) Order of Poles (kHz min.) (kHz max.) (dB min.) [fo-910kHz] within fo±1MHz (dB max.)(dB max.) Range (°C) XDCAF21M400RAA00P0 21.4000 Fundamental 2 ±7.5 ±25 @18dB 70 10 2.0 1.0 -20 to +70 XDCAF21M700MAA00P0 21.7000 Fundamental 2 ±3.75 ±20 @18dB 70 18 2.0 1.0 -20 to +70 XDCAG38M850PGA00P0 38.8500 Fundamental 4 ±5.0 ±25 @45dB 70 40 5.0 1.0 -20 to +70 XDCAG44M850QGA00P0 44.8500 Fundamental 4 ±6.5 ±12.5 @20dB 70 40 3.0 1.0 -20 to +70 XDCAG45M000RGA00P0 45.0000 Fundamental 4 ±7.5 ±25 @25dB 70 40 3.0 1.0 -20 to +70 XDCAG46M350PGA00P0 46.3500 Fundamental 4 ±5.0 ±20 @35dB 70 40 5.0 1.0 -20 to +70 XDCAG49M950PGA00P0 49.9500 Fundamental 4 ±5.0 ±20 @40dB 70 40 5.0 1.0 -20 to +70 XDCAG51M650PGA00P0 51.6500 Fundamental 4 ±5.0 ±12.5 @20dB 70 40 5.0 1.0 -20 to +70 XDCAG58M050MGA00P0 58.0500 Fundamental 4 ±4.0 ±20 @38dB 70 40 5.0 1.0 -20 to +70 XDCAH50M850PHA00P0 50.8500 Fundamental 4 ±5.0 ±25 @45dB 80 60 5.0 1.0 -20 to +70 XDCAH73M350QHA03P0 73.3500 Fundamental 4 ±6.0 ±25 @40dB 80 60 4.0 1.0 -20 to +70 XDCBA 3838 Size (3PN) Center Overtone Number 3dB Stop Band Guaranteed Spurious (dB min.) Insertion Ripple Operating Part Number Frequency Bandwidth Width Attenuation Loss Temperature (MHz) Order of Poles (kHz min.) (kHz max.) (dB min.) [fo-910kHz] within fo±1MHz (dB max.)(dB max.) Range (°C) 10 XDCBA47M250RAA02P0 47.2500 Fundamental 2 ±7.5 ±25 @15dB 60 2.0 1.0 -20 to +70 [fo+30kHz to 1000kHz] 4 XDCBA50M000MAA01P0 50.0000 Fundamental 2 ±3.75 ±16 @15dB 50 20 3.0 1.0 -20 to +70 [fo+100kHz to 1000kHz] 5 XDCBA70M200TAA01P0 70.2000 Fundamental 2 ±12.5 ±60 @18dB 50 2.5 1.0 -20 to +70 [fo+100kHz to 1000kHz] 30

!Note (cid:129) Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. P51E.pdf (cid:129) This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.10,2019 Test circuit R1 R1 R1 R1 IN G G C OUT G G S.G 50Ω C1 G OUT C1 L.M 50Ω S.G 50Ω C1 IN C G C1 L.M 50Ω Cc Part Number R1 (Ω) C1 (pF) Part Number R1 (Ω) C1 (pF) Cc (pF) XDCAF21M400RAA00P0 1450 2.5 XDCAG38M850PGA00P0 560 3.0 14.0 XDCAF21M700MAA00P0 800 8.0 XDCAG58M050MGA00P0 200 7.3 21.7 R1 R1 R1 R1 G C OUT IN G G G G G S.G 50Ω C1 IN C G C1 L.M 50Ω S.G 50Ω C1 G OUT C1 L.M 50Ω Cc 4 Part Number R1 (Ω) C1 (pF) Cc (pF) Part Number R1 (Ω) C1 (pF) XDCAH50M850PHA00P0 510 4.0 11.0 XDCBA47M250RAA02P0 420 6.0 XDCAH73M350QHA03P0 400 4.0 9.2 XDCBA50M000MAA01P0 220 7.5 XDCBA70M200TAA01P0 680 –1.0 31

!Note (cid:129) Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. P51E.pdf (cid:129) This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.10,2019 Frequency Characteristics XDCAF21M400RAA00P0 XDCAF21M700MAA00P0 c1: LOG 1 dB/ c1: LOG 1 dB/ c2: DLY 5 μsec/ REF 23.6 μsec c2: DLY 10 μsec/ REF 50.7 μsec c1: CNF 21.4 MHz SPF 40 kHz c1: CNF 21.7 MHz SPF 20 kHz c2: CNF 21.4 MHz SPF 40 kHz c2: CNF 21.7 MHz SPF 20 kHz XDCAG38M850PGA00P0 XDCAG58M050MGA00P0 c1: LOG 1 dB/ c1: LOG 1 dB/ c2: DLY 20 μsec/ REF 66.2 μsec c2: DLY 20 μsec/ REF 82.202379 μsec 4 c1: CNF 38.85 MHz SPF 20 kHz c1: CNF 58.05 MHz SPF 20 kHz c2: CNF 38.85 MHz SPF 20 kHz c2: CNF 58.05 MHz SPF 20 kHz XDCAH50M850PHA00P0 XDCAH73M350QHA03P0 c1: LOG 1 dB/ c1: LOG 1 dB/ c2: DLY 20 μsec/ REF 65.4 μsec c2: DLY 15 μsec/ REF 51.529μsec c1: CNF 50.85 MHz SPF 20 kHz c1: CNF 73.35 MHz SPF 30 kHz c2: CNF 50.85 MHz SPF 20 kHz c2: CNF 73.35 MHz SPF 30 kHz XDCBA50M000MAA01P0 c1: LOG 1 dB/ c2: LOG 10 dB/ c1: CNF 50 MHz SPF 30 kHz c2: CNF 50 MHz SPF 2 MHz 32

!Note (cid:129) Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. P51E.pdf (cid:129) This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.10,2019 Spurious XDCAF21M400RAA00P0 XDCAF21M700MAA00P0 c3: LOG 10 dB/ c3: LOG 10 dB/ c3: CNF 21.4 MHz SPF 2 MHz c3: CNF 21.7 MHz SPF 2 MHz XDCAG38M850PGA00P0 XDCAG58M050MGA00P0 c3: LOG 10 dB/ c3: LOG 10 dB/ 4 c3: CNF 38.85 MHz SPF 2 MHz c3: CNF 58.05 MHz SPF 2 MHz XDCAH50M850PHA00P0 XDCAH73M350QHA03P0 c3: LOG 10 dB/ c3: LOG 10 dB/ c3: CNF 50.85 MHz SPF 2 MHz c3: CNF 73.35 MHz SPF 2 MHz XDCBA50M000MAA01P0 c3: DLY 10 μsec/ REF 40.6 μsec c3: CNF 50 MHz SPF 30 kHz 33

!Note (cid:129) Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. P51E.pdf (cid:129) This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.10,2019 Notice Crystal Filters Chip Type XDCAF/XDCAG/XDCAH/XDCBA Series e Soldering and Mounting e 1. Standard Reflow Soldering Conditions (1) Reflow Filter is soldered twice within the following temperature Peak (260°C max.) conditions. 260 Flux: Please use rosin based flux, but do not use water C)220 soluble flux. ure (° (H2e2a0t°inCg) at er Pre-heating mp120 e (150-180°C) T 10 sec. max. 120 sec. max. 60 sec. max. 360 sec. max. (2) Soldering Iron 4 If compelled to mount the component by using a Condition soldering iron, please do not directly touch the Heating of the Soldering Iron 350°C max. component with the soldering iron. The component Soldering Time 5 sec. max. terminals or electrical characteristics may be damaged if excessive thermal stress is applied. 2. Wash Do not clean or wash the component. e Storage and Operating Conditions e 1. Product Storage Condition (2) Please do not put the products directly on the floor Please store the products in a room where the without anything under them to avoid damp places temperature/humidity is stable, and avoid places where and/or dusty places. there are large temperature changes. Please store the (3) Please do not store the products in places such as a products under the following conditions: damp heated place or any place exposed to direct Temperature: -10 to + 40°C sunlight or excessive vibration. Humidity: 15 to 85% R.H. (4) Please use the products immediately after the 2. Expiration Date on Storage package is opened, because the characteristics may Expiration date (shelf life) of the products is six months be reduced in quality and/or be degraded in after delivery under the conditions of a sealed and solderability due to storage under poor conditions. unopened package. Please use the products within six (5) Please do not drop the products to avoid cracking of months after delivery. If you store the products for a long the ceramic element. time (more than six months), use carefully because the 4. Other solderability may be degraded due to storage under poor (1) Please be sure to consult with our sales conditions. representative or engineer whenever the products are Please confirm solderability and characteristics for the to be used in conditions not listed above. products regularly. 3. Notice on Product Storage (1) Please do not store the products in a chemical atmosphere (Acids, Alkali, Bases, Organic gas, Sulfides and so on), because the characteristics may be reduced in quality and may be degraded in solderability due to storage in a chemical atmosphere. Continued on the following page. 34

!Note (cid:129) Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. P51E.pdf (cid:129) This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.10,2019 Notice Continued from the preceding page. e Rating e The component may be damaged if excessive mechanical stress is applied. e Handling e (1) For safety purposes, connect the output of filters to the (4)-3 Maximum Level IF amplifier through a D.C. blocking capacitor. Avoid An input level shall be less than a rated value. applying a direct current to the output of filters. If the input level beyond a rated value impressed, a (2) The component is recommended for placement crystal resonance characteristic will be deteriorated and machines employing optical placement capabilities. The the original characteristic will no longer be acquired as a component might be damaged by mechanical force crystal filter. depending on placement machine and condition. Make (4)-4 Separation between Input and Output sure that you have evaluated by using placement In order to prevent electromagnetic combination machines before going into mass production. Do not use between input and output, please have shielded placement machines employing mechanical positioning. certainly. If it has the combination between input and Please contact Murata for details beforehand. output, the incoming signal may go to the output side (3) Do not reuse components once mounted onto a circuit directly in the attenuation domain. The amount of board. guarantee attenuation will less achievable and the 4 (4) Crystal Filter original characteristic of crystal filter will no longer be You are requested to approve our data sheet and acquired. confirm the environment surrounding a crystal filter as There is grounding as one of the method. It enables to well. have the crystal filter grounded with attachment screw In order to demonstrate sufficient performance, please or grounding terminal. read the following notes. The internal part of crystal filter may be damaged, if it (4)-1 Necessity for LC Tuned Circuit solders to a case directly. In addition the case of a When the stray capacitance of the PCB that mounts a crystal filter is grounded certainly because potential crystal filter is large, a tuned circuit for offsetting the difference can be eliminated at the circuit side. stray capacitance may be needed. (4)-5 Direct-Current Superposition (4)-2 Termination Impedance When you charge direct-current, please do not have the The original characteristic in a pass band, insertion loss, current beyond a rated current value. Internal ripple and bandwidth characteristic are no longer transformer will generate a heat and it will create a acquired when termination impedance differs from a cause of bad insulation or disconnection, if excess direct rated value. The circuit impedance shall be measured current goes through filter than the rated value. accurately and it has consistency to match on termination conditions. Please keep in mind that a passage region will move in particular, if termination impedance does not match. 35

!Note (cid:129) Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. P51E.pdf (cid:129) This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.10,2019 Packaging Minimum Quantity/Dimensions of Reel (XDCAF/XDCAG/XDCAH Series) Embossed Tape ø330mm 3,000 (pcs.) 2.0 2.0 ø21.0 ø13.0 0 0 0. 0. 0 3 1 3 17.5 (in mm) 4 Dimensions of Carrier Tape Drawing Out Direction 2.0 4.0 ø1.5 75 0.3 1. 5 7. 0 0 6. 5 1 7. 5.50 8.0 ø1.5 1.80 (in mm) 36

!Note (cid:129) Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc. P51E.pdf (cid:129) This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. Sep.10,2019 Packaging Minimum Quantity/Dimensions of Reel (XDCBA Series) Embossed Tape ø180mm 1,000 (pcs.) 1.2 2.0 ø21.0 ø13.0 60.0 180.0 13.0 (in mm) 4 Dimensions of Carrier Tape Drawing Out Direction 2.0 4.0 ø1.5 75 0.3 1. 5 5. 0 5 2. 2 1 4. 4.25 8.0 ø1.5 1.35 (in mm) 37

P51E.pdf Sep.10,2019 Cat. No. P51E-3 Global Locations For details please visit www.murata.com Note 1 Export Control 2 Please contact our sales representatives or 3 Product specifi cations in this catalog are as of product engineers before using the products in October 2019. They are subject to change or For customers outside Japan: this catalog for the applications listed below, our products in it may be discontinued without No Murata products should be used or which require especially high reliability for the advance notice. Please check with our sales sold, through any channels, for use in the prevention of defects which might directly representatives or product engineers before design, development, production, utilization, damage a third party’s life, body or property, or ordering. If there are any questions, please contact maintenance or operation of, or otherwise when one of our products is intended for use our sales representatives or product engineers. contribution to (1) any weapons (Weapons of in applications other than those specified in Mass Destruction [nuclear, chemical or biological this catalog. 4 Please read rating and CAUTION (for storage, weapons or missiles] or conventional weapons) operating, rating, soldering, mounting and or (2) goods or systems specially designed or 1 Aircraft equipment handling) in this catalog to prevent smoking intended for military end-use or utilization by 2 Aerospace equipment and/or burning, etc. military end-users. 3 Undersea equipment 5 This catalog has only typical specifi cations. For customers in Japan: Therefore, please approve our product 4 Power plant equipment specifi cations or transact the approval sheet For products which are controlled items subject for product specifi cations before ordering. to the “Foreign Exchange and Foreign Trade Law” 5 Medical equipment of Japan, the export license specifi ed by the law 6 Please note that unless otherwise specifi ed, we is required for export. 6 Transportation equipment (vehicles, trains, shall assume no responsibility whatsoever for any ships, etc.) confl ict or dispute that may occur in connection 7 Traffi c signal equipment with the eff ect of our and/or a third party’s intellectual property rights and other related 8 Disaster prevention / crime prevention rights in consideration of your use of our products equipment and/or information described or contained in our catalogs. In this connection, no representation 9 Data-processing equipment shall be made to the eff ect that any third parties are authorized to use the rights mentioned above 10 Application of similar complexity and/or under licenses without our consent. reliability requirements to the applications listed above 7 No ozone depleting substances (ODS) under the Montreal Protocol are used in our manufacturing process. Murata Manufacturing Co., Ltd. www.murata.com