DATA SHEET SE5012T: 5 GHz Front End Module with Power Detector Applications Product Description  5 GHz WLAN (IEEE802.11a/g/n) The SE5012T is a 5GHz front end module offering  Access Points, PCMCIA, PC cards high linear power for wireless LAN applications. It incorporates a power detector for control of the output power. Features The SE5012T offers a high level of integration for a  5GHz Front End Module with PA, LNA and T/R simplified design, providing quicker time to market Switch and higher application board production yield. The  Integrated power amplifier enable pin (VEN) device integrates the input match, inter-stage match,  Buffered, temperature compensated power a temperature compensated, load insensitive power detector detector with 20dB of dynamic range, a 3.8GHz notch  High and Low-Linearity mode filter, a T/R switch and LNA.  5V or Direct-to-Battery operation For wireless LAN applications, the device meets the  3% EVM, 64 QAM, 54 Mbps: 17dBm @3.3V or requirements of IEEE802.11a and delivers 21dBm @5V approximately 17dBm of linear output power at  30 dB Typical Gain VCC=3.3V or 21dBm at VCC=5.0V. It also features a  Lead Free and RoHS compliant, halogen free low linearity mode control to reduce current package consumption at low power modes.  16 pin 3 mm x 3 mm x 0.6 mm QFN, MSL1 The SE5012T integrates the reference voltage generator, allowing for a true 1.8V CMOS compatible digital EN (enable) function to turn the power amplifier on and off. Ordering Information Part Number Package Remark SE5012T 16 Pin QFN Samples SE5012T-R 16 Pin QFN Tape and Reel SE5012T-EK1 Evaluation Kit Standard Functional Block Diagram VCC1,2 VPD H/L Lin C0 C1 EN Bias, Enable, Detector Circuits Match Match & TXIN Filter ANT RX Note: The TXIN has a DC short to ground. An external blocking capacitor is recommended at the TXIN port. Figure 1: Functional Block Diagram Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202395B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 23, 2012 1

DATA SHEET SE5012T: 5 GHz Front End Module with Power Detector Pin Out Diagram Figure 2: SE5012T Pin-Out Diagram Pin Out Description Pin Pin Name Description Name Description No. No. 1 EN PA Enable 9 VDD LNA Supply Voltage 2 GND Ground 10 GND Ground 3 TXIN 5GHz TX RF Input Signal 11 ANT 5GHz Antenna output 4 GND Ground 12 GND Ground 5 RX 5GHz LNA Output Signal 13 DET Power Detector Output 6 GND Ground 14 H/L Lin High-Low linearity Control 7 C0 Switch Control Logic 1 15 VCC1 Power Amplifier Supply Voltage 8 C1 Switch Control Logic 2 16 VCC2 Power Stage Supply Voltage Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202395B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 23, 2012 2

DATA SHEET SE5012T: 5 GHz Front End Module with Power Detector Absolute Maximum Ratings These are stress ratings only. Exposure to stresses beyond these maximum ratings for a long period of time may cause permanent damage to, or affect the reliability of the device. Avoid operating the device outside the recommended operating conditions defined below. This device is ESD sensitive. Handling and assembly of this device should be at ESD protected workstations. Symbol Definition Min. Max. Unit VCC Supply Voltage on pins VCC1, VCC2 -0.3 5.5 V VDD Supply Voltage on pin VDD -0.3 3.6 V EN DC input on Enable -0.3 3.6 V TXIN RF Input Power, RFout into 50Ω match - 12 dBm TSTG Storage Temperature Range -40 150 °C ESD HBM JEDEC JESD22-A114 all pins - 500 V Recommended Operating Conditions Symbol Parameter Min. Max. Unit VCC Supply Voltage on pins VCC1, VCC2 3.0 5.5 V VDD Supply Voltage on pin VDD 3.0 3.6 V TA Ambient Temperature -40 85 °C Control Logic Characteristics Conditions: VCC = 5.0 V; VDD = VEN = 3.3 V, TA = 25 °C, as measured on Skyworks Solutions’ SE5012T-EV1 evaluation board, unless otherwise noted. Symbol Parameter Conditions Min. Typ. Max. Unit POUT = 21 dBm, 54 Mbps, 64 QAM, VCC - 270 - = 5.0V, H/L Lin = 3.3V (High Linearity) ICC- Supply Current, POUT = 17 dBm, 54 Mbps, 64 QAM, VCC - 195 - 802.11a Transmit Mode = 3.3V, H/L Lin = 3.3V (High Linearity) mA POUT = 13 dBm, 54 Mbps, 64 QAM, VCC - 165 - = 3.3V, H/L Lin = 0V (Low Linearity) IDD LNA Supply Current VEN = C0 = 0V; C1 = 3.3V 13 VEN = 0 V, No RF, C0=C1=0 V Measured IOFF Supply Current - 20 50 μA on VCC, VDD pins VENH Logic High Voltage - 2.8 - 3.6 V VENL Logic Low Voltage - -0.3 - 0.3 V Input Current Logic IENH 10Kohm on chip pull down resistor - 330 400 μA High Voltage Input Current Logic IENL - - <1 - μA Low Voltage Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202395B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 23, 2012 3

DATA SHEET SE5012T: 5 GHz Front End Module with Power Detector Switch Logic Characteristics Conditions: VCC = 3.0 V to 5.5 V, VDD = VEN = 3.3 V, TA = 25 °C, as measured on Skyworks Solutions’ SE5012T- EK1 evaluation board, all unused ports terminated with 50 ohms, unless otherwise noted. Symbol Parameter Conditions Min. Typ. Max. Unit Low Loss Switch High State = VCTL_ON - ON 2.8 - 3.6 V Control Voltage VCTL_OFF High Loss Switch Low State = VCTL_OFF - OFF 0 - 0.3 V Control Voltage VCTL_OFF Control Input CCTL - - - 100 pF Capacitance ICTL Control Line Current VCTL = VCTL_ON - 2 10 uA Switch Control Logic Table C0 C1 EN Hi/L Lin ANT ON OFF ON OFF TX Low Linearity ON OFF ON ON TX High Linearity OFF OFF OFF D/C Rx Bypass OFF ON OFF D/C Rx LNA ON ON ON Un-supported state Note: D/C = don’t care Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202395B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 23, 2012 4

DATA SHEET SE5012T: 5 GHz Front End Module with Power Detector AC Electrical Characteristics Transmit Characteristics Conditions: VCC = 5.0V, VDD = VEN = C0 = H/L Lin = 3.3V, C1 = 0V, TA = 25 °C, as measured on Skyworks Solutions’ SE5012T-EV1 evaluation board, unless otherwise noted Symbol Parameter Conditions Min. Typ. Max. Unit fL-U Frequency Range - 5.15 - 5.85 GHz High Linearity VCC = 5.0 V - 21 - Mode Output Power H/L Lin = 3.3V VCC = 3.3 V - 17 - OFDM Signal, POUT dBm 64QAM, EVM Low Linearity VCC = 5.0 V - 17 - = 3% Mode H/L Lin = 0V VCC = 3.3 V - 13 - VCC = 5.0V - 27 - Output 1dB compression point, P1dB dBm No Modulation VCC = 3.3V - 23 - S11 Input Return Loss PIN = -25 dBm - 12 - dB 5V, High or Low 29 - 35 dB Linearity Mode Small Signal Gain, S21 PIN = -25dBm 3.3V, High or Low 28 - 33 Linearity Mode Gain variation over - - 0.5 single 40MHz channel ΔS21 Small Signal Gain Variation dB Gain Variation over - 3.5 - band S21_3.8 Out of Band Gain Gain at 3.8GHz - - 15 dB 2f - -50 -45.2 Harmonic POUT = 17 dBm, OFDM dBm/MHz 3f - -50 -45.2 tr, tf Rise and Fall Time - - 0.5 - us POUT = 17 dBm, 54 All non-harmonically related outputs less STAB Stability Mbps, 64 QAM, VSWR than -50 dBc/100 kHz = 6:1, all phases Constant PIN equal to POUT = 21 dBm at Rugged- Tolerance to output load 50ohms, 54 Mbps, 64 No damage ness mismatching QAM, VCC = 5.5V, VSWR = 6:1, all phases PIN = 12dBm, CW, Robust Robustness to input power No damage VSWR = 6:1, all phases Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202395B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 23, 2012 5

DATA SHEET SE5012T: 5 GHz Front End Module with Power Detector Receive Characteristics Conditions: VCC = 3.0 V to 5.5 V, VDD = C1 = 3.3V, VEN = C0 = 0V, TA = 25 °C, as measured on Skyworks Solutions’ SE5012T-EK1 evaluation board, all unused ports terminated with 50 ohms, unless otherwise noted. Symbol Parameter Condition Min. Typ. Max. Unit FOUT Frequency Range - 5.15 - 5.85 GHz Insertion Loss Bypass Mode: C0 = C1 = 0V - -5 - RX dB RX Gain High Gain Mode 11 12 - NF Noise Figure High Gain Mode - 2.5 - dB Input Return Loss At the Antenna port - -11 - RXRL Output Return dB At RX RF output - -8 - Loss Measured at ANT Port; High Gain - -5 - RxIP1DB Input P1DB Mode dBm LNA Bypass Mode - 10 - Max 2.4Ghz Rx_2.4int 1 dB degradation of IP1DB - - 0 dBm interferer power Transmit Power at VEN = C0 = H/L Lin = 3.3V, C1 = 0V TXLEAK RX Output 24dBm at the ANT port - -13 - dBm T/R on/off C0, C1 (50%) to RF output (10% or Ton/off switching speed 90%) - 300 - nSec Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202395B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 23, 2012 6

DATA SHEET SE5012T: 5 GHz Front End Module with Power Detector Power Detector Characteristics Conditions: VCC = 3.0 V to 5.5 V, VDD = VEN = C0 = 3.3V, C1 = 0V, f = 5.4 GHz, TA = 25 °C, as measured on Skyworks Solutions’ SE5012T-EV1 evaluation board, unless otherwise noted Symbol Parameter Conditions Min. Typ. Max. Unit PDR POUT detect range - 0 - P1dB dBm VDET22 Detector voltage POUT = 22 dBm 0.7 - 0.9 V VDET16 Detector voltage POUT = 16 dBm 0.50 - 0.60 V VDET2 Detector voltage POUT = 2 dBm 0.25 - 0.35 V PDZOUT Output Impedance - - 5 - KΩ Power Detector Performance over Frequency Figure 3: SE5012T Power Detector Characteristic Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202395B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 23, 2012 7

DATA SHEET SE5012T: 5 GHz Front End Module with Power Detector Package Diagram This package is Pb free and RoHS compliant. The product is rated MSL1. Figure 4: SE5012T Package Diagram Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202395B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 23, 2012 8

DATA SHEET SE5012T: 5 GHz Front End Module with Power Detector Recommended Land and Solder Patterns Figure 5: SE5012T Recommended Land and Solder Pattern Package Handling Information Because of its sensitivity to moisture absorption, instructions on the shipping container label must be followed regarding exposure to moisture after the container seal is broken, otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. The SE5012T is capable of withstanding a Pb free solder reflow. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. If the part is manually attached, precaution should be taken to insure that the device is not subjected to temperatures above its rated peak temperature for an extended period of time. For details on both attachment techniques, precautions, and handling procedures recommended, please refer to:  “Quad Flat No-Lead Module Solder Reflow & Rework Information”, Document Number QAD-00045  “Handling, Packing, Shipping and Use of Moisture Sensitive QFN”, Document Number QAD-00044 Caution! Class 1B ESD sensitive device Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202395B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 23, 2012 9

DATA SHEET SE5012T: 5 GHz Front End Module with Power Detector Branding Information SiGe 5012T Lot C ode Figure 6: SE5012T Branding Tape and Reel Information Parameter Value Devices Per Reel 3000 Reel Diameter 13 inches Tape Width 12 millimeters Figure 7: SE5012T-R Tape and Reel Information Document Change History Revision Date Notes 1.0 Nov 05, 2010 Created Updated package outline drawing Updated Max 2.5Ghz interferer power specification for LNA 1.1 Nov 14, 2011 Add TX leakage at RX output port Update operating frequency Update TX gain slope Updated current at 13dBm 1.2 Jan 31, 2012 RX S11, S22 1.3 Apr 03, 2012 Updated with Skyworks logo and disclaimer statement 1.4 Jun 14, 2012 Updated LNA gain Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202395B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 23, 2012 10

DATA SHEET SE5012T: 5 GHz Front End Module with Power Detector Copyright © 2012 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202395B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • October 23, 2012 11