DATA SHEET SE2432L: 2.4 GHz ZigBee®/Smart Energy Front-End Module Applications T 1 X U C S D T O C P S C B V C C  Smart meters 24 23 22 21 20  In-home appliances  Smart thermostats B2 1 19 VCC2 B1 2 18 GND Features TXP 3 17 N/C  Integrated PA with up to +24 dBm output power TXN 4 16 ANT_SEL  Integrated LNA with programmable bypass VB_OUT 5 15 ANT1  Integrated antenna switching with transmit and receive diversity function RXP 6 14 GND  Low NF: 2 dB typical RXN 7 13 ANT2  Differential transmit/receive interface with integrated baluns  Fast switch on/off time: <800 ns 8 9 10 11 12  Supply range: 2.0 V to 3.6 V N D D D D _I N N N N  Sleep mode current: 0.05 μA typical VB G G G G S2662  Small QFN (24-pin, 3 x 4 mm) package (MSL1, 260 °C per Figure 1. SE2432L Pinout – 24-Pin QFN JEDEC-J-STD-020) (Top View) Skyworks Green™ products are compliant with Description all applicable legislation and are halogen-free. For additional information, refer to Skyworks The SE2432L is a high performance, fully integrated RF Front-End Definition of Green™, document number Module (FEM) designed for ZigBee®/Smart Energy applications. SQ04-0074. The SE2432L is designed for ease of use and maximum flexibility. The device provides integrated and fully matched input baluns, an integrated inter-stage matching and harmonic filter, and digital controls compatible with 1.6 to 3.6 V CMOS levels. The RF blocks operate over a wide supply voltage range from 2.0 V to 3.6 V that allows the SE2432L to be used in battery powered applications over a wide spectrum of the battery discharge curve. The SE2432L is provided in a small, 24-pin, 3 x 4 mm Quad Flat No-Lead (QFN) package. The pin configuration and package are shown in Figure 1. A functional block diagram is shown in Figure 2. Signal pin assignments and functional pin descriptions are provided in Table 1. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 201696E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • March 10, 2014 1

DATA SHEET • SE2432L ZIGBEE/SMART ENERGY FEM L E S _ S X D T P T S N C C C A Logic control TXP PA TXN ANT1 Balun VB_OUT RXP ANT2 RXN Balun LNA N _I B V S2659 Figure 2. SE2432L Block Diagram Table 1. SE2432L Signal Descriptions Pin Name Description Pin Name Description 1 B2 Connect through bias resistor to pin 23 13 ANT2 Connect to 50 Ω antenna 2 B1 Connect through bias resistor to pin 23 14 GND Ground 3 TXP Positive transmit input signal from transceiver, 200 Ω 15 ANT1 Connect to 50 Ω antenna differential 4 TXN Negative transmit input signal from transceiver, 200 Ω 16 ANT_SEL Connect to GPIO signal to control antenna switch (see differential Table 7) 5 VB_OUT Transmit balun bias core supply from transceiver 17 N/C No connection (optional connection) 6 RXP Positive receiver output signal to transceiver, 200 Ω 18 GND Ground differential 7 RXN Negative receiver output signal to transceiver, 200 Ω 19 VCC2 Connect to positive supply differential 8 VB_IN Receive balun bias core supply from transceiver 20 CSD Connect to GPIO signal for mode control (see Table 9) (optional connection) 9 GND Ground 21 CPS Connect to GPIO signal for mode control (see Table 6) 10 GND Ground 22 VCC1 Connect to positive supply 11 GND Ground 23 BOUT Star connect to bias1 and bias 2 resistors 12 GND Ground 24 CTX Connect to GPIO signal for mode control (see Table 6) Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 2 March 10, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201696E

DATA SHEET • SE2432L ZIGBEE/SMART ENERGY FEM Table 2. SE2432L Absolute Maximum Ratings (Note 1) Parameter Symbol Minimum Maximum Units Supply voltage VCC1 –0.3 +3.6 V Supply voltage VCC2 –0.3 +3.8 (Note 2) V Control pin voltages –0.3 +3.6 V Transmit output power at ANT1 or ANT2 port into 50 Ω load POUT_TX_MAX +24 dBm Transmit input power at the TXN and TXP ports PIN_TX_MAX +6 dBm Receive input power at ANT1 or ANT2 ports PIN_RX_MAX +5 dBm Operating temperature TA –40 +125 C Storage temperature TSTG –40 +125 C Electrostatic discharge: ESD Human Body Model (HBM), Class 1C 1000 V Note 1: Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device. Note 2: Vcc2 is restricted to +3.6 V when operated at TA = 125 C. CAUTION: Although this device is designed to be as robust as possible, Electrostatic Discharge (ESD) can damage this device. This device must be protected at all times from ESD. Static charges may easily produce potentials of several kilovolts on the human body or equipment, which can discharge without detection. Industry-standard ESD precautions should be used at all times. Table 3. Recommended Operating Conditions Parameter Symbol Minimum Typical Maximum Units Supply voltage for balun bias VB_IN, VB_OUT 1.6 3.6 V Supply voltage on VCC pins VCC1, VCC2 2.0 3.0 3.6 V Operating temperature TA –40 +25 +125 C Electrical and Mechanical Specifications The state of the SE2432L is determined by the logic provided in Table 6. The absolute maximum ratings of the SE2432L are provided in Table 2. The recommended operating conditions are specified in Table 3 and electrical specifications are provided in Tables 4 through 8. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 201696E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • March 10, 2014 3

DATA SHEET • SE2432L ZIGBEE/SMART ENERGY FEM Table 4. SE2432L Electrical Specifications (Note 1) (VCC1 = VCC2 = 3.0 V, TA = +25 C, Unless Otherwise Noted) Parameter Symbol Test Condition Min Typical Max Units DC Characteristics Total supply current ICC_TX Transmit mode, CPS = CSD = CTX = 3.0 V: POUT = +20 dBm 110 mA POUT = +17 dBm 90 mA POUT = +10 dBm 45 mA Total supply current ICC_RX Receive mode, CPS = CSD 5 7 mA = 3.0 V, CTX = 0 V Total supply current ICC_RX_BYPASS Receive bypass mode, 300 μA CSD = 3.0 V, CPS = CTX = 0 V Sleep supply current ICC_OFF No RF, CTX = CPS = CSD 0.05 1.00 μA = 0 V Quiescent current ICQ No RF, 30 mA CPS = CSD = CTX = 3.0 V Logic Characteristics Control voltage: High VIH 1.6 3.6 V Low VIL 0 0.3 V Control current: High IIH 1 μA Low IIL 1 μA Dual Antenna Switch Characteristics Isolation between ANT1 and ANT2 ports ISOLANTSW –20 dB ANT1 to ANT2 switching time tANT1_ANT2 400 ns Note 1: Performance is guaranteed only under the conditions listed in this Table. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 4 March 10, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201696E

DATA SHEET • SE2432L ZIGBEE/SMART ENERGY FEM Table 5. SE2432L Electrical Specifications (1 of 2) (Note 1) (VB_IN = VB_OUT = 1.6 to 3.6 V, VCC1 = VCC2 = 3.0 V, TA = +25 C, All Unused Ports Terminated With 50 Ω, Unless Otherwise Noted) Parameter Symbol Test Condition Min Typical Max Units AC Transmit Characteristics Frequency range f 2400 2483 MHz Output power at ANT1 or ANT2 port POUT @ 2400 to 2483 MHz, OEVM = 1% typical, VCC1 = VCC2 =: 3.6 V +24.0 dBm 3.3 V +22.5 dBm 3.0 V +21.0 dBm 2.7 V +20.5 dBm 2.0 V +17.0 dBm Small signal gain, high power mode S21 @ 2400 to 2483 MHz 20 22 24 dB Small signal gain variation ΔS21 @ 2400 to 2483 MHz, 2 dBp-p across all ZigBee channels 2nd and 3rd harmonics 2fo, 3fo @ 2400 to 2483 MHz, –42 dBm/MHz POUT = +20 dBm, IEEE 802.15.4 source Output return loss S22 @ 2400 to 2483 MHz, –10 –5 dB ANT1 or ANT2 port Transmit port impedance ZIN 200 Ω Turn-on time tRISE From 50% of CTX edge to 800 ns 90% of final RF output power Turn-off time tFALL From 50% of CTX edge to 800 ns 10% of final RF output power Stability Stab CW, Pin = 0 dBm, All non-harmonically related outputs – 0.1 GHz to 20 GHz, < –42 dBm/MHz load VSWR = 6:1 Ruggedness RU CW, Pin = +6 dBm, No permanent damage – load VSWR = 10:1 AC Receive Characteristics Frequency range f 2400 2483 MHz Receive gain RX_GAIN @ 2400 to 2483 MHz, 10.0 11.5 13.0 dB CPS = CSD = logic “1,” CTX = logic “0” Receive Noise Figure NF @ 2400 to 2483 MHz, 2.0 2.5 dB CPS = CSD = logic “1,” CTX = logic “0” 3rd Order Input Intercept Point IIP3 @ 2400 to 2483 MHz, –3 +2 dBm CPS = CSD = logic “1,” CTX = logic “0” Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 201696E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • March 10, 2014 5

DATA SHEET • SE2432L ZIGBEE/SMART ENERGY FEM Table 5. SE2432L Electrical Specifications: (2 of 2) (Note 1) (VB_IN = VB_OUT = 1.6 to 3.6 V, VCC1 = VCC2 = 3.0 V, TA = +25 C, All Unused Ports Terminated With 50 Ω, Unless Otherwise Noted) Parameter Symbol Test Condition Min Typical Max Units AC Receive Characteristics (continued) 1 dB Input Compression Point IP1dB @ 2400 to 2483 MHz, –13 –8 dBm CPS = CSD = logic “1,” CTX = logic “0” 1 dB Input Compression Point in bypass IP1dB CPS = CTX = logic “0,” +10 dBm mode CSD = logic “1” Input return loss S11 @ 2400 to 2483 MHz, –10 –5 dBm ANT1 or ANT2 ports Receive port impedance ZOUT Measured differentially 200 Ω between RXP and RXN Turn-on time tRISE From 50% of CTX edge to 800 ns 90% of final RF output power Turn-off time tFALL From 50% of CTX edge to 800 ns 10% of final RF output power Gain in bypass mode G_BP CPW = CTX = logic “0,” –3 dB CSD = logic “1” Note 1: Performance is guaranteed only under the conditions listed in this Table. Table 6. SE2432L Mode Control Logic (Note 1) (VCC1 = VCC2 = 3.0 V, TA = +25 C) Mode Description CPS CSD CTX (Pin 21) (Pin 20) (Pin 24) 0 All off (sleep mode) (Note 2) 0 0 0 1 Receive bypass mode 0 1 0 2 Receive LNA mode 1 1 0 4 Transmit mode X 1 1 Note 1: “0” = 0 V. “1” = +3.0 V. “X” = don’t care (must be either 0 V or VCC voltage). Any state other than described in this Table places the switch into an undefined state. An undefined state will not damage the device. Note 2: All controls must be at logic “0” to achieve the specified sleep current. Table 7. SE2432L Antenna Enable Logic (VCC1 = VCC2 = 3.0 V, TA = +25 C) Description CPS CSD CTX ANT_SEL (Pin 21) (Pin 20) (Pin 24) (Pin 16) ANT1 port enabled X X X 0 ANT2 port enabled X X X 1 Note: “0” = 0 V. “1” = +3.0 V. “X” = don’t care. Any state other than described in this Table places the switch into an undefined state. An undefined state will not damage the device. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 6 March 10, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201696E

DATA SHEET • SE2432L ZIGBEE/SMART ENERGY FEM Evaluation Board Description Package Dimensions The SE2432L Evaluation Board is used to test the performance of The PCB layout footprint for the SE2432L is provided in Figure 6. the SE2432L FEM. The board is optimized for evaluation, Typical case markings are shown in Figure 7. Package experimentation, and investigation with an 802.15.4 signal dimensions for the 24-pin QFN are shown in Figure 8, and tape source. The design and layout can be quickly and easily and reel dimensions are provided in Figure 9. transferred into a production design. An Evaluation Board schematic diagram is provided in Figure 3. A Package and Handling Information reference design schematic is provided in Figure 4. Table 8 describes the pins on the power and control I/O header (J27). Instructions on the shipping container label regarding exposure to Table 9 provides the Bill of Materials (BOM) list for Evaluation moisture after the container seal is broken must be followed. Board components. A photograph of the Evaluation Board is Otherwise, problems related to moisture absorption may occur shown in Figure 5. when the part is subjected to high temperature during solder assembly. Evaluation Board Setup Procedure The SE2432L is rated to Moisture Sensitivity Level 1 (MSL1) at 260 C. It can be used for lead or lead-free soldering. For 1. Connect J21, J23, J25, and J26 to 50 Ω instruments. additional information, refer to the Skyworks Application Note, Terminate all unused ports (if applicable) with 50 Ω. Solder Reflow Information, document number 200164. 2. Connect the supply ground to pins 19 and 20 of J27. Care must be taken when attaching this product, whether it is 3. Connect 3.0 V to pins 15 and 16 of J27. done manually or in a production solder reflow environment. Production quantities of this product are shipped in a standard 4. Connect 1.8 V to pins 7 and 8 of J36. tape and reel format. 5. Connect 3.0 V to pins 3 and 4 of J27. NOTE: By following the logic in Table 6, the required RF path is selected. Refer to Tables 7 and 8 for antenna port control. 6. Monitor the 2.5 GHz amplifier transmit performance by applying an RF signal to J25 and monitoring the output power on J26 (ANT1) or J23 (ANT2). CAUTION: Care should be taken not to overdrive the amplifier by applying too much RF on the input to the device. A suitable starting input power would be –20 dBm. 7. Monitor the 2.5 GHz amplifier receive performance by applying an RF signal to J26 (ANT1) or J23 (ANT2) and monitoring the output signal on J25. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 201696E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • March 10, 2014 7

DATA SHEET • SE2432L ZIGBEE/SMART ENERGY FEM J27 VCC 2 1 VCC VDD 4 3 VDD VB_OUT 6 5 VB_OUT C38 2.2 μF VB_IN 8 7 VB_IN CTX 10 9 CPS 12 11 CSD 14 13 VCC2 16 15 ANT_SEL 18 17 20 19 Mode Control Power Supply R32 C37 C40 100 kΩ 2.2 μF 10 pF Mode Control Mode Control R35 100 kΩ R31 100 kΩ Power Supply R30 R25 1.2 kΩ 1.2 kΩ 24 23 22 21 20 C32 X T 1 S D T U C P S 100 nF U5 C BO VC C C (Note 2) J25 1 UN_BAL N/C 6 × 1 B2 VCC2 19 23 RBFA_LG_PNTD BALG_NPDT 54 2 B1 GND 18 1C04 p2F 10C 4p4F 3 TXP N/C 17 × 4 TXN ANT_SEL 16 Antenna Switch Control J26 DC ConneTctriaonns (mOipt tBioanluanl) 5 VB_OUT ANT1 15 Antenna 1 6 RXP GND 14 R33 U6 7 RXN ANT2 13 J23 100 kΩ J21 1 UN_BAL N/C 6 × N Antenna 2 2 RF_GND GND 5 _I D D D D 3 BAL_PT BAL_PT 4 VB GN GN GN GN C45 8 9 10 11 12 10 pF Receive Balun DC Connection (Optional) Notes: 1. The following components are for evaluation purposes only and can be removed in the final application: C38, C44, C45, C46, J27, R31, R32, R33, R35, U5, and U6. 2. L19 is made of a trace between the VCC2 pin and the C42/C32 capacitors. 3. PCB Recommendations: Metal Layer 1 = RF traces + control lines. Core thickness between top RF layer and ground plane is critical. Metal Layer 2 = Solid ground plane. No traces routing. Metal Layer 3 and 4 = Control lines + VCC traces (no VCC plane). Pore copper on each layer connected to the ground plane. Use VCC traces in a star distribution pattern. Always use 4 layers. S2723 Figure 3. SE2432L Evaluation Board Schematic Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 8 March 10, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201696E

DATA SHEET • SE2432L ZIGBEE/SMART ENERGY FEM Power Supply C40 10 pF Mode Control Mode Control Mode Control Power Supply C37 2.2 μF R30 R25 1.2 kΩ 1.2 kΩ 24 23 22 21 20 C32 X T 1 S D T U C P S 100 nF C O C C C B V (Note 2) 1 B2 VCC2 19 2 B1 GND 18 C42 10 pF Positive Transmit 3 TXP N/C 17 × from Transceiver 4 TXN ANT_SEL 16 Antenna Switch Control L1 DNI 5 VB_OUT ANT1 15 Antenna 1 (Note 1) 6 RXP GND 14 Negative Transmit from Transceiver 7 RXN ANT2 13 Antenna 2 Transmit Balun N DC Connection (Optional) _I D D D D B N N N N V G G G G Positive Receive to Transceiver 8 9 10 11 12 L2 DNI (Note 1) Negative Receive to Transceiver Receive Balun DC Connection (Optional) Notes: 1. Optional component: use to fine-tune match and provide DC path on both sides of the differential line. S2722 2. L19 is made of a trace between the VCC2 pin and the C42/C32 capacitors. Figure 4. SE2432L Reference Design Schematic Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 201696E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • March 10, 2014 9

DATA SHEET • SE2432L ZIGBEE/SMART ENERGY FEM Table 8. Power and Analog I/O Header: J27, 10x2 Pin Pin Name Description Recommended Setting 1, 2, 15 VCC Supply voltage General purpose VCC provided as the main power supply 3, 4, 9, 11, 12,13,17 VDD Digital supply voltage Connect to separate power supply voltage 5, 6 VB_OUT Bias output – 7, 8 VB_IN Supply voltage Optional DC connection for transceiver 16 VCC2 Supply voltage General purpose VCC provided as the main power supply 10 CTX Control 12 CPS Control See Tables 6 and 7 14 CSD Control 18 ANT_SEL Control 19, 20 GND Ground General purpose ground Table 9. SE2432L Evaluation Board Bill of Materials (BOM) (Note 1) Component Value Size Manufacturer Mfr Part Number Characteristics C32 100 nF 0402 Murata GRM155R71C104KA88D Monolithic ceramic C37, C38 2.2 μF 0805 Murata GRM21BR71A225KA01L Ceramic capacitor, 2.2 UF, 10V, 10%, X7R 0805 C40, C42, C44, C45 10 pF 0402 Murata GRM1555C1H100JZ01 Multilayer ceramic J21, J23, J25, J26 SMA End launch Johnson 142-0701-851 SMA end launch straight jack Components receptacle – tab contact J27 10X2 100MIL Samtec TSW-110-07-G-D 100 mil header R25, R30 1.2 kΩ 0402 Panasonic ERJ2GEJ122 Thick film chip resistor R31, R32, R33, R35 100 kΩ 0402 Panasonic ERJ2GEJ104 Thick film chip resistor U3 – 3 x 4 mm QFN Skyworks Solutions, SE2432L 2.4 GHz ZigBee FEM with Inc. differential transmit/receive U5, U6 – 2 x 1.25 mm TDK HHM1521 Multilayer 2.4 GHz chip baluns Note 1: Schematic and BOM have been designed to optimize performance in 802.11a/n applications. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 10 March 10, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201696E

DATA SHEET • SE2432L ZIGBEE/SMART ENERGY FEM Figure 5. SE2432L Evaluation Board Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 201696E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • March 10, 2014 11

DATA SHEET • SE2432L ZIGBEE/SMART ENERGY FEM 4.40 5 2 2 5 0.20 Typ. 0.400 Typ. 0 5 5 0 1. 0. 0 0. 1. X X X X X 19 18 17 16 15 14 13 3183 3 3143 0.60 Typ. 20 12 12 3X 0.54 11 21 11 1.60 22 103.40 3X 0 0 23 9 3X 0.54 9 24 8 1 2 3 4 5 6 7 0 2.60 15X ø0.25 Board Metal Via Pattern (Note 4) 4.50 4.40 5on7 %ce snoteldre pra cdoverage 0.30 Typ. 0.400 Typ. 0.20 Typ. 0.400 Typ. 19 18 17 16 15 14 13 19 18 17 16 15 14 13 0.70 Typ. 0.60 Typ. 20 12 20 12 21 11 21 11 1.5022 10 0.20 22 103.40 0.53 Typ. 23 9 23 9 24 8 24 8 1 2 3 4 5 6 7 Package 1 2 3 2.450 5 6 7 0.20 Outline 1.03 Typ. Solder Mask Pattern Stencil Pattern (Note 6) (Note 5) Notes: 1. All dimensions are in millimeters 2. Dimensioning and tolerancing according to ASME Y14.5M-1994 3. Unless specified, dimensions are symmetrical about center lines. 4. Via hole recommendations: 0.025 mm Cu via wall plating (minimum), soldermask on the far side should tent or plug via holes. 5. Stencil recommendations: 0.10 mm stencil thickness, laser cut apertures, trapezoidal walls and rounded corners offer better paste release. 6. Solder mask recommendations: contact board fabricator for recommended solder mask offset and tolerance. S2663 Figure 6. PCB Layout Footprint Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 12 March 10, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201696E

DATA SHEET • SE2432L ZIGBEE/SMART ENERGY FEM Pin 1 Indicator Pin 1 e4 Part Number SiGe Lot Code 2432L Lot Code Figure 7. Typical Case Markings 0.850 ± 0.050 1.600 ± 0.050 2X 0.10 C 3.000 ± 0.050 A 0.10 M C A B B See Note 3 0.203 Ref. 0.30 X 45° 24 23 22 21 20 20 21 22 23 24 0.10 M C A B 1 19 19 1 2 18 18 2 3 17 17 3 4.000 ± 0.050 4 16 2.600 ± 0.050 16 4 R0.075 0.400 5 15 15 Typ. 5 6 14 14 6 7 13 13 7 0.250 Min. Seating Plane 0.282 2X 0.10 C 8 9 10 11 12 0–0.050 12 11 10 9 8 0.118 C 24X 0.200 ± 0.050 0.07 M C A B 24X 0.400 ± 0.050 0.05 M C Top View Side View Bottom View Notes: 1. All measurements are in millimeters. 2. Dimensions and tolerances according to ASME Y14.5M-1994. Unless otherwise specified, the following values apply: Decimal Tolerance: Angular Tolerance: X.X (1 place) ± 0.1 mm ±1° X.XX (2 places) ± 0.05 mm X.XXX (3 places) ± 0.025 mm 3. Terminal #1 identification mark located within marked area. Y0675 4. Unless specified, dimensions are symmetrical about center lines. Figure 8. SE2432L 24-Pin QFN Package Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 201696E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • March 10, 2014 13

DATA SHEET • SE2432L ZIGBEE/SMART ENERGY FEM 8.00 ∅1.5 +0.1/–0.0 4.00 (Note 1) 1.75 ± 0.10 2.00 ± 0.05 (Note 3) ∅1.50 Min. A 0.30 ± 0.05 5 R0.3 Max. 5.50 ± 0.0(Note 3) 0 ± 0.30 4.40 2. 1 A 0.12 1.10 3.40 Pin 1 Indicator A 0.12 Notes: R0.25 1. 10 sprocket hole pitch cumulative tolerance ±0.2. 2. Camber in compliance with EIA 481. 3. Pocket position relative to sprocket hole measured as true position of pocket, not pocket hole. 4. All measurements are in millimeters. S2742 Figure 9. SE2432L Tape and Reel Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 14 March 10, 2014 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 201696E

DATA SHEET • SE2432L ZIGBEE/SMART ENERGY FEM Ordering Information Model Name Manufacturing Part Number Evaluation Board Part Number SE2432L ZigBee/Smart Energy FEM SE2432L-R SE2432L-EK1 Copyright © 2011, 2013-2014 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks, the Skyworks symbol, and “Breakthrough Simplicity” are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 201696E • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • March 10, 2014 15