Features • 6W Class II AC-DC LED power supply • 350mA, 500mA and 700mA CC/CV output AC/DC Converter • Fused input and SCP, OVP, OLP, OTP LED • 3kVAC isolation • Universal input voltage range Driver RACD06 • Low cost Description 6 Watt A compact universal input 6W constant current switching power module suitable for driving up to 12 CC/CV high power LEDs.The output (dual constant voltage / constant current mode) current limit is fixed at 350mA, 500mA or 700mA. At lower output currents, the output is constant voltage. Single Output Selection Guide Part Input CC CV Efficiency Rated Number Voltage Range Mode Mode (1) typ. Power nom./max. [VAC] [VDC] [mA] [VDC] [mA] [%] [W] RACD06-350 90-264 3-22 350 24 0-300 79 6 / 7.2 RACD06-500 90-264 3-12 500 none 70 6 RACD06-700 90-264 3-8.4 700 12 0-600 72 6 / 7.2 All LED Drivers may not be used without a load. They must be switched on the primary side only. Noncompliance may damage the LED or reduce its lifetime. Model Numbering E340696 RACD06-___ nom. Output Power nom. Output Current Specifications (measured @ Ta= 25°C, nom. Vin, rated load and after warm-up unless otherwise stated) BASIC CHARACTERISTICS UL8750 certified UL1310 certified Parameter Condition Min. Typ. Max. CAN/CSA-C22.2 No. 223-M91 certified 90VAC 230VAC 264VAC IEC/EN61347 certified Input Voltage Range IEC/EN61347-2-13 certified 120VDC 370VDC ENEC certified Input Current full load, 100VAC 200mA PSE certified Inrush Current 115VAC/230VAC, <2ms 10A CB Report 350mA 26VDC Open Circuit Voltage no load 500mA 17VDC 700mA 14VDC Input Frequency Range 47Hz 63Hz 115VAC 0.40 Power Factor full load 230VAC 0.55 Hold-up Time 18ms Output Ripple Current 200mAp-p continued on next page www.recom-power.com REV.: 1/2019 L-1

RACD06 AC/DC Converter Series Specifications (measured @ Ta= 25°C, nom. Vin, rated load and after warm-up unless otherwise stated) Constant Current (CC) and Constant Voltage (CV) (1) CV RACD06-350 24V 22V RACD06-500 RACD06-700 e g 12V a olt ut V 81.24VV CV p Out CC CC CC 3V Output Current 3035 50 6070 00 0 00 mm m mm AA A AA Nominal Current Limits Notes: Note1: CV Mode is approved by Recom internal quality standard, but not certified PROTECTION Parameter Condition Value Input Fuse T2A, slow blow Short Circuit Protection (SCP) continuous, current limit Overload Protection (OLP) 120% typ. Over Temperature Protection (OTP) shutdown, automatic resatart after cooling down Isolation Voltage I/P to O/P 3.75kVAC / 1 minute Notes: Note2: Refer to local safety regulations if input over-current protection is also required Maximum loading of automatic circuit breakers* * @ 115VAC, 1Ohm, 90° phase angle and max. load * @ 230VAC, 1Ohm, 90° phase angle and max. load Circuit Breaker Circuit Breaker Current Circuit Breaker Circuit Breaker Current Typ 10A 16A 20A 25A Typ 10A 16A 20A 25A B 80 157 200 254 C 221 247 337 430 C 265 317 437 550 ENVIRONMENTAL Parameter Condition Value according to UL RACD06-350 -20°C to +50°C Operating Temperature Range RACD06-500, RACD06-700 -20°C to +40°C according to ENEC all -20°C to +50°C according to UL RACD06-350 +75°C max. Max. Case Temperature RACD06-500, RACD06-700 +70°C max. according to ENEC all +70°C max. IP Rating IP20 Operating Humidity non condensing 5%-85% RH Design Lifetime +25°C ambient 20 x 103 hours continued on next page www.recom-power.com REV.: 1/2019 L-2

RACD06 AC/DC Converter Series Specifications (measured @ Ta= 25°C, nom. Vin, rated load and after warm-up unless otherwise stated) Derating Graph RACD06-350 100 90 80 70 %] d [ 60 a o ut L 50 p ut 40 O 30 20 10 0 -20 -10 0 10 20 30 40 50 60 Ambient Temperature [°C] SAFETY AND CERTIFICATIONS Certificate Type (Safety) Report Number Standard Standard for LED Equipment for use in Lighting Products UL8750, 1st Edition, 2009 Standard for Class 2 Power Units E340696-1-3 UL1310, 5th Edition, 2010 Extra Low Voltage Class 2 Outputs CAN/CSA-C22.2 No. 223-M91, 2nd Edition, 2009 Equipment for general Lighting Purpose EMC Immunity Requirements (CB scheme) SH12051509-002 IEC61547, 2nd Edition, 2009 Lamp Controlgear Particular Requirements (CB scheme) 12CA61275-1 IEC/EN61347-2-13, 2006 Lamp Controlgear Particular Requirements SH12051508-002 EN61347-2-13,2006 IEC61347-1, 2nd Edition, 2010 Lamp Controlgear General Requirments for Safety (CB scheme) 12CA61275-1 EN61347-1, 2nd Edition, 2011 Lamp Controlgear General Requirments for Safety SH12051508-002 EN61347-1, 2nd Edition, 2008 Luminaires General Requirements and Tests EN60598-1, 2009 SH12051508-003 Luminaires with built-in transformers for filament lamps EN60598-2-6, 1997 D.C. or A.C. Controlgears for LED Performance Requirements (CB scheme) 12CA61275-2 IEC/EN62384, 2009 Lamp Controlgear General Requirments for Safety (ENEC License) EN61347-1 ENEC-00610 Lamp Controlgear Particular Requirements (ENEC License) EN61347-2-13 Lamp Controlgear General Requirments for Safety (PSE) J61347-1 Lamp Controlgear Particular Requirements (PSE) J63147-2-13 RoHS RoHS 6/6, 2011/65/EU EAC RU Д- AT.A Г03. В.67369 TP TC 004/020, 2011 EMC Compliance Condition Standard / Criterion EMC for industrial, scientific and medical equipment (design to meet) FCC18, Class A Limits and methods of measurement of radio disturbance characteristics of EN55015, Class A electrical lighting and similar equipment (design to meet) CISPR15, 7th Edition, 2009 Limits and methods of measurement of radio disturbance characteristics of J55015 electrical lighting and similar equipment (PSE) Limits of harmonic current emissions IEC61000-3-2, 3rd Edition, 2009 Voltage Fluctuations and Flicker in Public Low-Voltage Systems <=16A per phase IEC61000-3-3, 2nd Edition, 2008 www.recom-power.com REV.: 1/2019 L-3

RACD06 AC/DC Converter Series Specifications (measured @ Ta= 25°C, nom. Vin, rated load and after warm-up unless otherwise stated) DIMENSION and PHYSICAL CHARACTERISTICS Parameter Type Value Material case plastic (UL94V-0) Dimension (LxWxH) 68.0 x 35.0 x 21.0mm Weight 34g Dimensions Drawing (mm) Connection via Screw Terminal Ø3.0 15.0 # Function Solid Wire Stranded Wire (3) AWG 1 VAC in (N) 0.75-1.5mm² 0.75-1.5mm² 18-16 1.5 3 2 VAC in (L) 0.75-1.5mm² 0.75-1.5mm² 18-16 1 4 FC 23.5 34 LLEEDD+- 00..7755--11..55mmmm²² 00..7755--11..55mmmm²² 1188--1166 C F wire stripping length: 5mm tc recommended tightening torque: 0.22Nm tc= case temperature measuring point 0 FC = fixing centers 1 3. Tolerance: xx.x= ±0.5mm 2 1 xx.xx= ±0.35mm 2 Mounting screws are included FC 64.0 58.0 35.0 0 1. 2 0 5 1. 68.0 Notes: Note3: The use of sleeve or ferrule terminations is recommended INSTALLATION and APPLICATION Connection L N LED+ LED- www.recom-power.com REV.: 1/2019 L-4

RACD06 AC/DC Converter Series Specifications (measured @ Ta= 25°C, nom. Vin, rated load and after warm-up unless otherwise stated) PACKAGING INFORMATION Parameter Type Value Packaging Dimension (LxWxH) cardboard Box 215.0 x 80.0 x 70.0mm Packaging Quantity 10pcs Storage Temperature Range -30° to +80°C Storage Humidity non-condensing 5%-85% RH The product information and specifications may be subject to changes even without prior written notice.The product has been designed for various applications; its suitability lies in the responsibility of each customer. The products are not authorized for use in safety-critical applications without RECOM’s explicit written consent. A safety-critical application is an application where a failure may reasonably be expected to endanger or cause loss of life, inflict bodily harm or damage property. The applicant shall indemnify and hold harmless RECOM, its affiliated companies and its representatives against any damage claims in connection with the unauthorized use of RECOM products in such safety-critical applications. www.recom-power.com REV.: 1/2019 L-5

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: R ECOM: RACD06-350 RACD06-700 RACD06-500