PTC-10 10 mm Cermet Potentiometer FEATURES • Cermet resistive element. • IP54 protection according to IEC 60529. • Plastic material according to UL94V-0. • Alumina substrate. • Also upon request: Low torque version. Available as SPDT switch. Laser trimming for tighter tolerances. Wiper positioned at initial, 50% or fully clockwise. Supplied in magazines for automatic insertion. Long life model for low cost control applications. Special tapers. Mechanical detents. ELECTRICAL SPECIFICATIONS MECHANICAL SPECIFICATIONS –Range of values*: –Mechanical rotation angle: 235° ± 5° –Electrical rotation angle: 220° ± 20° –Tolerance*: ± 20% –Torque: 0.4 to 2 Ncm. ± 30% (0.6 to 2.7 in-oz) –Max. Voltage: 200 VDC (lin) 100 VDC (no lin) –Stop torque: > 5 Ncm. ( >7 in-oz) –Nominal Power 70°C (158°F) (see power rating curve) 0.33 W (lin) 0.17 W (no lin) –Life*: Up to 10K cycles –Taper* (Log. & Alog. only Rn 1K) Lin ; Log; Alog. –Residual resistance*: –Equivalent Noise Resistance: –Operating temperature:standard: -40°C to +90°C (-40°F to +194°F) * Others check availability upon request: -40°C to +120°C (-40°F to +248°F) HOW TO ORDER OPTIONAL EXTRAS PTC-10 L H01 101 A 2020 Code Mounting Series Code Method Taper Life Magazine Shaft / rotor colour Torque PTC-10 H01 H2.5H05 H5H02 A =H L2i.n5.PH10 H5P E= Long life T RO= Red – = Standard V05 V5V10 V B = Log. NE= Black V11 VP C = Alog. (See note 5) (See note 6) VE= Green L= Low Torque Rotors AM= Yellow B V13 VJ AZ= Blue (See note 8) G Value Detents MA= Brown KL 101 = 100 W Tolerance PAI Shaft /Thum. GNAR== OGrraenyge PAM M 0505 = ± 5% RW (See note 2) 504 = 500 K 0707 = ± 7% PPA1FI 0012 == FFiigg.. 12 (See note 7) X 1010 = ± 10% P1F Wiper position YZ 050005 == C5 MM 2020 = ± 20% P0..2 17 = Fig. 17 PM = 50% 3030 = ± 30% . (See note 1) (See note 3) (See note 4) P16 (See note 9) PF = Final NOTES: (1) "Z" adjustment only available on "H" versions. Rotor "G" only available in purple (shaft/rotor colour "VI"). (2) Terminal styles: "P" & "J" are crimped terminals. V=Vertical adjust; H=Horizontal Adjust (3) Value Example: Code: 10 1 Numb of zeros First two digits of the value. 000 = CM: SPDT switch 45° (4) Non standard tolerance, check Example: +7% Code: 07 05 (5) • Standard = 1000 cycles • Long = 10K cy c l e s -5% negative tolerance Others check availability. positive tolerance (6) Magazines: not available with the H10, V05 and V13 models, nor with adjustment types X, W, Y, Z. Non flammable: housing, rotor and shaft. (7) Colour shaft/rotor: Potentiometer without shaft: only rotor Potentiometer with shaft: only shaft (8) Low Torque: 1 Ncm No detent option available for low torque models. (9) If you want to use your own custom plastic shaft/knob/actuator please contact Piher for advice about compatible materials. www.piher.net 43

HOW TO ORDER CUSTOM DRAWING STANDARD OPTIONS Detents None Packing Bulk PTC-10 LH 01 + DRAWING NUMBER (Max. 16 characters) Rotor colour Natural Shaft colour Natural This way of ordering should be used for options which are not included Wiper position Initial in the "How to order" standard and optional extras. Torque Standard Life 1000 cycles ROTORS Rotors (Default delivery is at initial position. Wipers are shown positioned at 50% for the picture) Without shaft or knob. With inserted shaft. 0.8 2 2 2.2 2 1.7 51.4º 0.7 2.2 1.6 1 2. 2 L L L = Screwdriver M = Hexagonal G = Hexagonal K = Cross slot R B AdjustXab =le from AdjusWtab l=e from All rotors are thru-hole. collector side terminal side With knob/humbwheel inserted 6.5 0.8 6.5 0.8 3 3 7 7 3.5 1.95 3.5 3.75 Y = Adjustable from terminal side (default knob is 5034). Z = Adjustable from collector side (default knob is 5034). MOUNTING METHODS V = horizontal mounting – vertical adjustment H = vertical mounting – horizontal adjustment V05 V10 4.8+0.2 10.3+0.1 +0.1 4.8+0.2 10.3+0.1 +0.1 1.3 1.3 2.5 3 2.5 S 4 5 5 5 5 10 10 5 5 2.5 2.5 A E +0.2 3.5 5 +0.2 3.5 5 5 6.5 3.5 5 6 3.5 1+0.1 1+0.1 A = Initial S = Wiper E = Final V11 V13 4.8 10.3 4.8 10.3 1.3 1.3 4 4 5 5 5 10 510 5 10 510 5 5 5 5 5 6 3.3 5 6 3.3 www.piher.net 44

ROTORS V = horizontal mounting – vertical adjustment H = vertical mounting – horizontal adjustment H01 H02 +0.2 +0.1 4.8 10.3 2.5 4.8 10.3 2.5 2 0. + 1 2 5 2. 0. 1 +7 2.1 5 A E +0.1 1 7 1.3 3 2.5 2.5 2.5 1+0.1 S 3.5 3. 1.3 2.5 2.5 2.5 1 A = Initial S = Wiper E = Final H05 H10 +0.2 +0.1 4.8 10.3 5 4.8 10.3 5 2 0. + 2 1 0. 5 12. +7 2.1 5 1 7 +0.1 1.3 3 2.5 2.5 5 1+0.1 3.5 3. 1.3 2.5 2.5 5 1 SMD versions Crimped terminals - detail V11, V13, H02, H10 models feature “crimped” terminals that provide greater stability during the soldering process. 2.5 Detail 2 5.7 10.3 31 2.05 2 +0.-0. 5.75 10.9 5.15 9.4 5 7 1.6 +0.2 +0.2 2 2.5 2.5 6 6 2.5 2.5 9.3 9.3 3.3 -0.1 0.9 OPTIONS 1 CONTACT SPDT SWITCH A SW Standard specs. Power Rating: 0 24V / 15mA ON position resistance: 5 1 CONTACT Insulation Resistance: 30 M E 4 Please contact Piher 50 0 50 % for ordering information. 45º 45º Mechanical rotation angle: 235º±5º www.piher.net 45

TAPERS POSITIONING A = Linear 100% Rn P.M. B = Log. 50% +20º C C = Alog. A % B + 5 P.F. 2 R CCW CW Standard Special example Std. Position = CCW NOTE = Please note relative terminal positions when ordering non linear tapers. TESTS TYPICAL VARIATIONS ELECTRICAL LIFE 1.000 h. @ 70°C; 0.33 W ±5 % MECHANICAL LIFE (CYCLES) 1000 @ 10 CPM ...15 CPM ±2 % (Rn < 1 MW) TEMPERATURE COEFFICIENT –40°C; +90°C ±100 ppm (Rn <100 K) THERMAL CYCLING 16 h. @ 90°C; 2h. @ –40°C ±2.5 % DAMP HEAT 500 h. @ 40°C @ 95% HR ±5 % VIBRATION (for each plane X,Y,Z) 2 h. @ 10 Hz. ... 55 Hz. ±2 % NOTE: Out of range values may not comply these results. PACKAGING +1.5 540 BOXES 7.6 Model Units Without shaft 1000 (80 x 85 x 185 mm.) Magazines for PTC-10 h 2.5; h 5 9 8. With thumbwheel 800 (80 x 85 x 185 mm.) 1 Also crimped term. h 2.5 P With shaft 400 (80 x 85 x 185 mm.) 540+1.5 AUTOMATIC INSERTION Magazines Units Magazines for PTC-10 V 5 3. 1 Also crimped term. VP PTC-10H & PTC-10V 50 Pieces 12 POWER RATING CURVE W(%) 100 % 40 % C 70 90 www.piher.net 46

SHAFTS (for G and M rotor types, top view) Shafts, knobs & thumbweels are delivered at random position. Positioning available check availability. 3 3.1 5 5 8.1 10.4 10 34 8.4 7 3. 6 2. Fig. 1 / Ref. 5016 Fig. 2 / Ref. 5053 Fig. 3 / Ref. 5012 Fig. 4 / Ref. 6053 Fig. 6 / Ref. 5035 4.9 4.9 4.9 4.9 8.1 5 7 5 6. 5.5 15.2 5.5 12. 2 2 6 2. Fig. 7 / Ref. 5115 Fig. 8 / Ref. 5116 Fig. 9 / Ref. 5119 Fig. 10 / Ref. 5120 Fig. 11 / Ref. 5027 2- GANG Plastic Knob/ Plastic Shaft* 4.9 25 13 8.1 4.5 5.2 Ø6 1 5 7 6. 12.75 3 3. Ø1.3 5 2.5 5 Fig. 18 / Ref. 6064 * Delivered unassembled Fig. 12 / Ref. 6052 Fig. 13 / Ref. 5121 Fig. 14 / Ref. 5055 (For assembled contact your nearest PIHER supplier) For R rotor THUMBWHEELS (for G and M rotor types, top view) THUMBWHEEL type only Shafts, knobs & thumbweels are delivered at random position. Positioning available check availability. Marking: configurable number of positions. Example of four positions marking: 11.5 12 9.5 1.5 1 5 1 1 1 2 9 1 Fig. 5 / Ref. 5034 Fig. 15 / Ref. 6008 Fig. 16 / Ref. 5039 Fig. 17 / Ref. 5062 check availability www.piher.net 46

DETENT CONFIGURATIONS EXAMPLES This innovative PT´s with detents family has been specifically developed to allow the integration of otherwise large and expensive external mechanisms into the body of the PAM P1I P1F P02 P03 majority of the 10 & 15 mm. PS/PT/PTC potentiometer series thusallowing a high range of configurations: special tapers, torque, tolerances, linearity, cut track, etc. This detent design not only adds a P04 P05 P06 P07 P08 "click" sensation of position, but also offers enormous savings in both cost and space for any given application. Strong and weak detents can be mixed as per customer´s request. P09 P10 P16 Detent number and positions can be made or fitted to the customer needs or preferences. Relative detent positions A along the total mechanical A A= 26º travel. PID B= 27.5º PFD Unless otherwise Wiperposition poWsiitpioenr specified the detents are evenly spaced (using the end points as reference) B B B B PAI PAF (wiper positioned at initial) (wiper positioned at final) NOTES FOR DETENTED VERSIONS: (5) Detent torque can vary from 1.2 to 2.5 times the standard (1) Detents not available for V05 mounting. potentiometer torque. These cases are studied individually. (6) Please consult your nearest Piher supplier if unique (2) For more than 10 detents versions please contact your non-overlapping values at each detent position or nearest PIHER authorised distributor. LOG/ALOG tapers are required. (3) Standard mechanical life is 500 cycles. (7) Different output voltage values can be matched at each (4) Long life versions are available under request and have the detent position (upon request). following characteristics at Tª: - Potentiometers with 1 to 3 detents: up to 10K cycles - Potentiometers with 4 and more detents: up to 5K cycles 10.3 Detents detail. 4.8 (7 detents example) 3 9º 0 1 5 For custom voltage outputs in any detent position see next page. www.piher.net 47

STEPPED OUTPUTS Constant value zones can be combined with strategically located stops matching the flat areas of the output. PIHER’s potentiometers can If you require this feature, please, send us your requirements to sales@piher.net feature special stepped outputs or ‘constant voltage zones’ for Stepped outputs version example (10 steps version): the 10mm and 15mm product families. 100% Un when the potentiometer’s wiper position is located at detent 88.9% Un nº9, the output votage will be 88.9% Un ± % tolerance. These constant voltage zones 77.7% Un can be combined with PIHER’s 5 6 66.6% Un 4 7 26° mechanical detents to provide exact alignment between the 55.5% Un 3 8 electrical output (flat areas) 44.4% Un 2 9 and the mechanical detent 33.3% Un 1 0º 234º10 position. The result is a higher 22.2% Un level of precision in controlling S lighting, temperature, motor or 11.1% Un A S E A E other electronic control 0% Un / 0º 100% 50% Wiper position systems. A E = = = = = = = = = 1 2 3 4 5 6 7 8 9 10 In addition to established catalogue detent configurations, we will design and manufacture any other configuration on our tried-and- Improved repeatability tested carbon/cermet & By combining the constant value zones with the detents, engineers THM/SMD potentiometer can align the same voltage values with each of the detent stops technology and processes. when rotating the control both forward and backward. This provides clear mechanical positions that are not only repeatable, With its precise control but perfectly aligned electrical outputs at each of the (detent) angles. capabilities, our 10mm and 15mm potentiometers series Piher’s detents also prevent output values from changing due to are well suited for many vibration or accidental rotor movements, furthering reliable control consumer applications such as consistency. lighting (dimmers), power hand tools, relays, timers and HVAC systems. Design tip. Cost-effectiveness Main advantages Unique, non-overlapping values at each stop (detent position) Absolute encoders can easily be replaced connecting the potentiometer to It prevents changes in the output value due to light vibration or accidental the microprocessor’s rotor micro-movements analogue input. Fully customisable according to customer´s needs Cost effective replacement for absolute encoders RECOMMENDED CONNECTIONS V CC E Piher potentiometer’s recommended connection circuit for a position sensor or S control application. R AD (voltage divider circuit electronic design). A RL C Noise filter. Ground. R 100 x R L www.piher.net 44

Disclaimer Contact The product information in this catalogue is for reference purposes. Please consult for the most up to date and accurate design information. Piher Sensors & Controls SA Piher Sensors & Controls S.A., its affiliates, agents, and employees, and all persons acting on its or their behalf Polígono Industrial Municipal (collectively, “Piher”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein Vial T2, 22, or in any other disclosure relating to any product described herein. 31500 Tudela - Spain. Piher disclaims any and all liability arising out of the use or application of any product described herein or of any t. +34-948-820450 information provided herein to the maximum extent permitted by law. The product specifications do not expand or f. +34-948-824050 otherwise modify Piher’s terms and conditions of sale, including but not limited to the warranty expressed therein, which apply to these products. sales@piher.net No licence, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Piher. www.piher.net The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless otherwise expressly indicated. Customers using or selling Piher products not expressly indicated for use in such applications do so entirely at their own risk and agree to fully indemnify Piher for any damages arising or resulting from such use or sale. Please contact authorised Piher personnel to obtain written terms and conditions regarding products designed for such applications. Product names and markings noted herein may be trademarks of their respective owners. Information contained in and/or attached to this catalogue may be subject to export control regulations of the European Community, USA, or other countries. Each recipient of this document is responsible to ensure that usage and/or transfer of any information contained in this document complies with all relevant export control regulations. If you are in any doubt about the export control restrictions that apply to this information, please contact the sender immediately. For any Piher International Corp. Exports, Note: All products / technologies are EAR99 Classified commodities. Exports from the United States are in accordance with the Export Administration Regulations. Diversion contrary to US law is prohibited. Piher is an AmphenolTM company. ISO 14001 BUREAU VERITAS Certification Note: Piher products can be adapted to meet customer’s requirements. Due to continuous process improvement, specifications are subject to change without notice. v111018 www.piher.net

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: A mphenol: PTC10LH01-502A2020 PTC10YH-2.55K PTC10MH012022020 PTC10LH01-252A2020 PTC10MV10-224A2020 PTC10YV103A2020 PTC10MH01-104A2020 PTC10MH01-103A2020 PTC10MH01202A2020 PTC10MH01- 754A2020 PTC10LH01-501A2020 PTC10LV10-00621-PTC10LV10-202A2020 PTC10LV500AP PTC10LV10- 504A2020 PTC10LV10-203A2020 PTC10LV10-252A2020 PTC10LH01-103C2020 PTC10MV502A2020 PTC10LV10- 103ADISC PTC10LH01-203A2020 PTC10LH01-251A2020 PTC10LV10-101A2020 PTC10LV501AP PTC10LH01- 503A2020 PTC10KV11472A-2020 PTC10LH01-201A2020 PTC10LH01-101A2020 PTC10LV10-201A2020 PTC10WV10203A202003GR PTC10LV10-253A2020 PTC10LH01-202A2020 PTC10LH01-504A2020 PTC10LH01- 253A2020 PTC10LH01-254A2020 PTC10LV10-254A2020 PTC10LH01-102A2020 PTC10LV10-501A2020 PTC10LV10-502A2020 PTC10LH01-204A2020 PTC10LV10-102A2020 PTC10LV10-104A2020 PTC10LH01- 103A2020 PTC10LV10-503A2020 PTC10LV10-204A2020 PTC10LH01-104A2020 PTC10WV10203A202003CREAM PTC10LV10-202A2020 PTC10LV10-103A2020 PTC10LV10-105A2020 PTC10YH01-104A2020-05 PTC10LV10- 104A1010-P10-Stepped PTC10LV10-103A1010 PTC10MV11-103A2020 PTC10LV10-104A0505 PTC10WV10- 104A2020-08-NE PTC10MV10-104A0505 PTC10MV10-472A0505 PCT10LV10-103A1010-P10 PTC10LH01- 503A1010 PTC10LV10-104A1010 PTC10LV10-503B1010 PTC10MV10-104A1010-P10-Stepped PTC10LH01- 103A1010 PTC10MV10-105A2020 PTC10MV10-103A2020 PTC10LH01-104A1010 PTC10LV10-472A0505