Chip Phototransistor with Right Angle Lens PT12-21C/TR8 Features ․Fast response time ․High photo sensitivity ․Small junction capacitance ․Package in 8mm tape in “7” diameter reel ․Pb free ․The product itself will remain within RoHS compliant version. ․Compliance with EU REACH ․Compliance Halogen Free .(Br <900 ppm ,Cl <900 ppm , Br+Cl < 1500 ppm). Descriptions ․PT12-21C/TR8 is a phototransistor in miniature SMD package which is molded in a water clear epoxy with spherical top view lens The device is spectrally matched to infrared emitting diode. Applications ․Miniature switch ․Counters and sorter ․Position sensor ․Infrared aoolied system Device Selection Guide Part Category Chip Material Lens Color PT Silicon Water clear 1 Copyright © 2017, Everlight All Rights Reserved. Release Date : 2017/6/1. Issue No: DPT-0000509 . Rev:4 www.everlight.com

Data Sheet Chip Phototransistor With Right Angle Lens PT12-21C/TR8 Package Dimensions Notes: 1.All dimensions are in millimeters Notes: 2.Tolerances unless dimensions ±0.1mm Notes: 3.Suggested pad dimension is just for reference only. .Please modify the pad dimension based on individual need. 2 Copyright © 2017, Everlight All Rights Reserved. Release Date : 2017/6/1. Issue No: DPT-0000509 . Rev:4 www.everlight.com

Data Sheet Chip Phototransistor With Right Angle Lens PT12-21C/TR8 Absolute Maximum Ratings (Ta=25℃) Parameter Symbol Rating Units Collector-Emitter Voltage Vceo 30 V Emitter-Collector-Voltage Veco 5 V Collector Current Ic 50 mA Operating Temperature T -25 ~ +85 ℃ opr Storage Temperature T -40 ~ +85 ℃ stg Soldering Temperature T 260 ℃ sol Power Dissipation at (or below) P 75 mW c 25℃Free Air Temperature Notes: *1: Soldering time≦5 seconds. Electro-Optical Characteristics (Ta=25℃) Parameter Symbol Condition Min. Typ. Max. Units Range Of Spectral Bandwidth λ --- 730 --- 1100 nm 0.5 Wavelength Of Peak Sensitivity λ --- --- 940 --- nm P Collector-Emitter Breakdown Ic=100μA BVceo 30 --- --- V Voltage Ee=0mW/cm2 Emitter-Collector Breakdown Ic=100μA BVeco 5 --- --- V Voltage Ee=0mW/cm2 Collector-Emitter Saturation Ic=2mA Vce(sat) --- --- 0.4 V Voltage Ee=1mW/cm2 Vce=20V Collector Dark Current I --- --- 100 nA ceo Ee=0mW/cm2 Vce=5V On State Collector Current Ic(on) 0.30 1.14 --- mA Ee=1mW/cm2 3 Copyright © 2017, Everlight All Rights Reserved. Release Date : 2017/6/1. Issue No: DPT-0000509 . Rev:4 www.everlight.com

Data Sheet Chip Phototransistor With Right Angle Lens PT12-21C/TR8 Typical Electro-Optical Characteristics Curves 4 Copyright © 2017, Everlight All Rights Reserved. Release Date : 2017/6/1. Issue No: DPT-0000509 . Rev:4 www.everlight.com

Data Sheet Chip Phototransistor With Right Angle Lens PT12-21C/TR8 Precautions For Use 1. Over-current-proof Customer must apply resistors for protection, otherwise slight voltage shift will cause big current change (Burn out will happen). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the Phototransistor should be kept at 10℃~30℃ and 90%RH or less. 2.3 The Phototransistor suggested be used within one year. 2.4 After opening the package, the devices must be stored at 10℃~30℃ and ≦ 60%RH, and used within 168 hours (floor life). If unused Phototransistor remain, it should be stored in moisture proof packages. 2.5 If the moisture absorbent material (desiccant material) has faded or unopened bag haexceeded the shelf life or devices (out of bag) have exceeded the floor life, baking treatment is required. 2.6 If baking is required, refer to IPC/JEDEC J-STD-033 for bake procedure or recommend the following conditions: 96 hours at 60℃± 5℃and <5 % RH (reeled/tubed/loose units) 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the Phototransistor during heating. 3.4 After soldering, do not warp the circuit board. 5 Copyright © 2017, Everlight All Rights Reserved. Release Date : 2017/6/1. Issue No: DPT-0000509 . Rev:4 www.everlight.com

Data Sheet Chip Phototransistor With Right Angle Lens PT12-21C/TR8 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the Phototransistor have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the Phototransistor will or will not be damaged by repairing. Package Dimensions 6 Copyright © 2017, Everlight All Rights Reserved. Release Date : 2017/6/1. Issue No: DPT-0000509 . Rev:4 www.everlight.com

Data Sheet Chip Phototransistor With Right Angle Lens PT12-21C/TR8 Note: The tolerances unless mentioned are ±0.1mm, Unit: mm Carrier Taping Dimensions: Loaded Quantity 2000PCS/Reel Note: The tolerances unless mentioned are ±0.1mm, Unit: mm 7 Copyright © 2017, Everlight All Rights Reserved. Release Date : 2017/6/1. Issue No: DPT-0000509 . Rev:4 www.everlight.com

Data Sheet Chip Phototransistor With Right Angle Lens PT12-21C/TR8 Label Form Specification CPN: Customer’s Production Number P/N : Production Number LOT No: Lot Number QTY: Packing Quantity HUE: Peak Wavelength CAT: Ranks REF: Reference MSL-X: MSL Level Made In: Manufacture place DISCLAIMER 1. EVERLIGHT reserves the right(s) on the adjustment of product material mix for the specification. 2. The product meets EVERLIGHT published specification for a period of twelve (12) months from date of shipment. 3. The graphs shown in this datasheet are representing typical data only and do not show guaranteed values. 4. When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from the use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets. 5. These specification sheets include materials protected under copyright of EVERLIGHT. Reproduction in any form is prohibited without obtaining EVERLIGHT’s prior consent. 6.This product is not intended to be used for military, aircraft, automotive, medical, life sustaining or life saving applications or any other application which can result in human injury or death. Please contact authorized Everlight sales agent for special application request. EVERLIGHT ELECTRONICS CO., LTD. Tel: 886-2-2685-6688 Office: No. 6-8, Zhonghua Rd., Shulin Dist., Fax: 886-2685-2699，6897 New Taipei City 23860, Taiwan http://www.everlight.com 8 Copyright © 2017, Everlight All Rights Reserved. Release Date : 2017/6/1. Issue No: DPT-0000509 . Rev:4 www.everlight.com