PHOTOCOUPLER PS9121 HIGH CMR, 15 Mbps OPEN COLLECTOR OUTPUT TYPE 5-PIN SOP (SO-5) 3.3 V PHOTOCOUPLER −NEPOC Series− DESCRIPTION The PS9121 is an optically coupled high-speed, active low type isolator containing a GaAlAs LED on the input side and a photodiode and a signal processing circuit on the output side on one chip. The PS9121 is designed specifically for high common mode transient immunity (CMR) and low pulse width distortion. The PS9121 is suitable for high density application. FEATURES • Low power consumption (VCC = 3.3 V) • Pulse width distortion (⏐tPHL − tPLH⏐ = 35 ns MAX.) PIN CONNECTION • High common mode transient immunity (CMH, CML = ±15 kV/μs MIN.) (Top View) • Small package (SO-5) 5 4 3 • High-speed (15 Mbps) • High isolation voltage (BV = 3 750 Vr.m.s.) 1.Anode 2.Cathode • Open collector output 3.GND • Ordering number of taping product: PS9121-F3, F4: 2 500 pcs/reel 4.VO 5.VCC • Pb-Free product • Safety standards 1 2 • UL approved: File No. E72422 • DIN EN60747-5-2 (VDE0884 Part2) approved No.40008902 (option) • CSA approved: File No. 2115283 (CA 101391) TRUTH TABLE LED Output ON L APPLICATIONS OFF H • Measurement equipment • PDP • FA Network Document No. PN10502EJ05V0DS (5th edition) Date Published August 2008 NS The mark <R> shows major revised points. The revised points can be easily searched by copying an "<R>" in the PDF file and specifying it in the "Find what:" field.

PS9121 PACKAGE DIMENSIONS (UNIT: mm) 3.4+0.3 –0.1 5 4 3 7.0±0.3 4.4 1 2 0.2 +0.105–0.05 ± 1 2.6 0. 1 1.27 0.5±0.3 0. ± 0.1 0.4+–00..0150 0.25 M <R> MARKING EXAMPLE SnBi PLATING Ni/Pd/Au PLATING 9121 Type Number 9121 Type Number N831 Assembly Lot N831 Assembly Lot *1 No. 1 pin Mark *1 No. 1 pin Mark N 8 31 N 8 31 Week Assembled Week Assembled Year Assembled Year Assembled (Last 1 Digit) (Last 1 Digit) Rank Code Rank Code *1 Bar : Pb-Free *1 Bar : Pb-Free 2 Data Sheet PN10502EJ05V0DS

PS9121 <R> ORDERING INFORMATION Solder Plating Safety Standards Application Part Number Order Number Packing Style *1 Specification Approval Part Number PS9121 PS9121-A Pb-Free 20 pcs (Tape 20 pcs cut) Standard products PS9121 PS9121-F3 PS9121-F3-A (SnBi) Embossed Tape 2 500 pcs/reel (UL approved) PS9121-F4 PS9121-F4-A PS9121-V PS9121-V-A 20 pcs (Tape 20 pcs cut) DIN EN60747-5-2 PS9121-V-F3 PS9121-V-F3-A Embossed Tape 2 500 pcs/reel (VDE0884 Part2) PS9121-V-F4 PS9121-V-F4-A approved (Option) PS9121 PS9121-AX Pb-Free 20 pcs (Tape 20 pcs cut) Standard products PS9121-F3 PS9121-F3-AX (Ni/Pd/Au) Embossed Tape 2 500 pcs/reel (UL approved) PS9121-F4 PS9121-F4-AX PS9121-V PS9121-V-AX 20 pcs (Tape 20 pcs cut) DIN EN60747-5-2 PS9121-V-F3 PS9121-V-F3-AX Embossed Tape 2 500 pcs/reel (VDE0884 Part2) PS9121-V-F4 PS9121-V-F4-AX approved (Option) *1 For the application of the Safety Standard, following part number should be used. Data Sheet PN10502EJ05V0DS 3

PS9121 ABSOLUTE MAXIMUM RATINGS (TA = 25°C, unless otherwise specified) Parameter Symbol Ratings Unit Diode Forward Current*1 IF 30 mA Reverse Voltage VR 5 V Detector Supply Voltage VCC 7 V Output Voltage VO 7 V Output Current IO 25 mA Power Dissipation*2 PC 40 mW Isolation Voltage*3 BV 3750 Vr.m.s. Operating Ambient Temperature TA −40 to +85 °C Storage Temperature Tstg −55 to +125 °C *1 Reduced to 0.3 mA/°C at TA = 25°C or more. *2 Applies to output pin VO (collector pin). Reduced to 1.5 mW/°C at TA = 65°C or more. *3 AC voltage for 1 minute at TA = 25°C, RH = 60% between input and output. Pins 1-2 shorted together, 3-5 shorted together. RECOMMENDED OPERATING CONDITIONS Parameter Symbol MIN. TYP. MAX. Unit Low Level Input Voltage VFL 0 0.8 V High Level Input Current IFH 6.3 10 12.5 mA Supply Voltage VCC 2.7 3.3 3.6 V TTL (RL = 1 kΩ, loads) N 5 Pull-up Resistor RL 330 4 k Ω 4 Data Sheet PN10502EJ05V0DS

PS9121 ELECTRICAL CHARACTERISTICS (TA = −40 to +85°C, unless otherwise specified) Parameter Symbol Conditions MIN. TYP.*1 MAX. Unit Diode Forward Voltage VF I F = 10 mA, TA = 25°C 1.4 1.65 1.8 V Reverse Current IR V R = 3 V, TA = 25°C 10 μA Terminal Capacitance Ct V = 0 V, f = 1 MHz, TA = 25°C 30 pF Detector High Level Output Current IOH V CC = VO = 3.3 V, VF = 0.8 V 1 80 μA VCC = VO = 5.5 V, VF = 0.8 V 1*2 Low Level Output Voltage*3 V OL V CC = 3.3 V, IF = 5 mA, IOL = 13 mA 0.2 0.6 V VCC = 5.5 V, IF = 5 mA, IOL = 13 mA 0.2*2 High Level Supply Current ICCH V CC = 3.3 V, IF = 0 mA, VO = Open 4 7 mA VCC = 5.5 V, IF = 0 mA, VO = Open 5*2 Low Level Supply Current ICCL V CC = 3.3 V, IF = 10 mA, VO = Open 7 10 VCC = 5.5 V, IF = 10 mA, VO = Open 9*2 Coupled Threshold Input Current IFHL V CC = 3.3 V, VO = 0.8 V, RL = 350 Ω 2.5 5 (H → L) VCC = 5 V, VO = 0.8 V, RL = 350 Ω 2.5*2 Isolation Resistance RI-O V I-O = 1 kVDC, RH = 40 to 60%, 1011 Ω TA = 25°C Isolation Capacitance CI-O V = 0 V, f = 1 MHz, TA = 25°C 0.6 pF Propagation Delay Time tPHL TA = 25°C 40 75 ns (H → L)*4 VCC = 3.3 V, RL = 350 Ω, IF = 7.5 mA 100 VCC = 5 V, RL = 350 Ω, IF = 7.5 mA 37*2 Propagation Delay Time tPLH TA = 25°C 45 75 (L → H)*4 VCC = 3.3 V, RL = 350 Ω, IF = 7.5 mA 100 VCC = 5 V, RL = 350 Ω, IF = 7.5 mA 40*2 Rise Time tr V CC = 3.3 V, RL = 350 Ω, IF = 7.5 mA 20 VCC = 5 V, RL = 350 Ω, IF = 7.5 mA 20*2 Fall Time tf V CC = 3.3 V, RL = 350 Ω, IF = 7.5 mA 5 VCC = 5 V, RL = 350 Ω, IF = 7.5 mA 5*2 Pulse Width Distortion ⏐tPHL-tPLH⏐ VCC = 3.3 V, RL = 350 Ω, IF = 7.5 mA 5 35 (PWD)*4 VCC = 5 V, RL = 350 Ω, IF = 7.5 mA 3*2 Propagation Delay Skew tPSK V CC = 3.3 V, RL = 350 Ω, IF = 7.5 mA 40 Common Mode CMH V CC = 3.3 V, RL = 350 Ω, TA = 25°C, 15 20 kV/μs Transient Immunity at High IF = 0 mA, VO > 2 V, VCM = 1 kV Level Output*5 VCC = 5 V, RL = 350 Ω, TA = 25°C, 20*2 IF = 0 mA, VO > 2 V, VCM = 1 kV Common Mode CML V CC = 3.3 V, RL = 350 Ω, TA = 25°C, 15 20 Transient Immunity at Low IF = 7.5 mA, VO < 0.8 V, VCM = 1 kV Level Output*5 VCC = 5 V, RL = 350 Ω, TA = 25°C, 20*2 IF = 7.5 mA, VO < 0.8 V, VCM = 1 kV Data Sheet PN10502EJ05V0DS 5

PS9121 *1 Typical values at TA = 25°C *2 These values are reference values. *3 Because VOL of 2 V or more may be output when LED current input and when output supply of VCC = 2.6 V or less, it is important to confirm the characteristics (operation with the power supply on and off) during design, before using this device. *4 Test circuit for propagation delay time Input (IF = 7.5 mA) Pulse input (IF) VCC = 3.3 V 50% (PW = 1 μ s, 0.1 μ F RL = 350 Ω Duty cycle = 1/10) VO (monitor) Input CL = 15 pF Output (monitor) 1.5 V 47 Ω VOL tPHL tPLH Remark CL includes probe and stray wiring capacitance. *5 Test circuit for common mode transient immunity 1 kV VCM 90% SW IF VCC = 3.3 V 0.1 μ F RL = 350 Ω 10% 0 V CL = 15 pFVO (monitor) tr tf VO VOH (IF = 0 mA) 2 V VCM 0.8 V VO VOL (IF = 7.5 mA) Remark CL includes probe and stray wiring capacitance. USAGE CAUTIONS 1. This product is weak for static electricity by designed with high-speed integrated circuit so protect against static electricity when handling. 2. By-pass capacitor of 0.1 μF is used between VCC and GND near device. Also, ensure that the distance between the leads of the photocoupler and capacitor is no more than 10 mm. 3. Avoid storage at a high temperature and high humidity. 6 Data Sheet PN10502EJ05V0DS

PS9121 TYPICAL CHARACTERISTICS (TA = 25°C, unless otherwise specified) MAXIMUM FORWARD CURRENT DETECTOR POWER DISSIPATION vs. AMBIENT TEMPERATURE vs. AMBIENT TEMPERATURE 40 50 A) W) m m nt I (F 30 n P (C 40 e o d Curr 20 ssipati 30 ar Di m Forw Power 20 mu 10 or 10 Maxi etect D 0 20 40 60 8085 100 0 20 40 60 8085 100 Ambient Temperature TA (˚C) Ambient Temperature TA (˚C) FORWARD CURRENT vs. SUPPLY CURRENT vs. FORWARD VOLTAGE AMBIENT TEMPERATURE 100 12 A)A) mm nt I (mA)F 10 TA = ++5805˚˚CC urrent I (CCHurrent I (CCL 108 ICCL (VCC = 3.3 V, IF = 10 mA) Curre 1 +250˚˚CC ply Cply C 6 ard –25˚C SupSup 4 ICCH (VCC = 3.3 V, IF = 0 mA) Forw 0.1 Level Level 2 h w HigLo 0.01 0 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 –50 –25 0 25 50 75 100 Forward Voltage VF (V) Ambient Temperature TA (˚C) LOW LEVEL OUTPUT VOLTAGE vs. OUTPUT VOLTAGE vs. INPUT CURRENT AMBIENT TEMPERATURE 3.5 0.6 3 VCC = 3.3 V V) VIF C=C 5=. 03 .m3 AV, (OL 0.5 V (V)O 2.5 RL = 13.500 k ΩΩ age V 0.4 ge 2 4.0 kΩ, 4.7 kΩ Volt IOL = 16.0 mA Output Volta 1.51 evel Output 00..32 11306...000 mmmAAA L 0.5 w 0.1 o L 0 0 1 2 3 4 5 6 –50 –25 0 25 50 75 100 Input Current IF (mA) Ambient Temperature TA (˚C) Remark The graphs indicate nominal characteristics. Data Sheet PN10502EJ05V0DS 7

PS9121 THRESHOLD INPUT CURRENT vs. PROPAGATION DELAY TIME vs. AMBIENT TEMPERATURE AMBIENT TEMPERATURE 5.0 120 mA) VVCOC = = 0 3.6.3 V V, (ns)H 100 VIF C=C 7=. 53 .m3 AV, tPLH: RL = 4.7 kΩ ut Current I (FHL 43..00 RL = 315.00 kΩΩ ay Time t, tPHLPL 8600 tPLtHP:L HR: LR =Lt P1=L. H03: 5 kR0ΩL Ω= 4.0 kΩ p 2.0 el n D hreshold I 1.0 4.0 kΩ pagation 4200 tPHL: RL = 350 Ω, 1.0 kΩ, 4.0 kΩ, 4.7 kΩ T o Pr 0 0 –50 –25 0 25 50 75 100 –50 –25 0 25 50 75 100 Ambient Temperature TA (˚C) Ambient Temperature TA (˚C) PULSE WIDTH DISTORTION vs. SWITCHING TIME vs. AMBIENT TEMPERATURE AMBIENT TEMPERATURE 100 300 –t (ns)PLH 80 VIF C=C 7=. 53 .m3 AV, ns) 250 VIF C=C 7=. 53 .m3 AV, tr:t rR: RL L= = 4 4.7.0 k ΩkΩ ortion tPHL 60 RL = 4R.L7 =k Ω4.0 kΩ Time t, t (rf 210500 e Width Dist 4200 RL =R 1L .=0 3k5Ω0 Ω Switching 10500 tttrrf::: RRRLLL === 3 3155.000 Ω kΩ,Ω 1.0 kΩ, 4.0 kΩ, 4.7 kΩ s ul P 0 0 –50 –25 0 25 50 75 100 –50 –25 0 25 50 75 100 Ambient Temperature TA (˚C) Ambient Temperature TA (˚C) PROPAGATION DELAY TIME vs. INPUT CURRENT 120 ns) VCC = 3.3 V tPLH: RL = 4.7 kΩ (H 100 PL me t, tPHL 80 tPLH: RL = t1PL.0H: kRΩL = 4.0 kΩ y Ti 60 tPLH: RL = 350 Ω a el D n 40 o agati 20 tPHL: RL = 350 Ω, 1.0 kΩ, 4.0 kΩ, 4.7 kΩ p o Pr 0 5 7 9 11 13 15 Input Current IF (mA) Remark The graphs indicate nominal characteristics. 8 Data Sheet PN10502EJ05V0DS

PS9121 TAPING SPECIFICATIONS (UNIT: mm) Outline and Dimensions (Tape) 1 0. 2.0±0.05 ± 4.0±0.1 1.5+–00. 1 1.75 ±0.1 3.45 MAX. 4 7. 1 2 0. 0. ± ± 5 0 5. 2. 1 1.55±0.1 3.9±0.1 3.0±0.1 8.0±0.1 0.3±0.05 Tape Direction PS9121-F3 PS9121-F4 Outline and Dimensions (Reel) 2.0±0.5 2.0±0.5 13.0±0.2 0 0 2 2. 1. 0. ± ± ± 0 0 0 R 1.0 21.0±0.8 φ33 φ10 φ13. 13.5±1.0 17.5±1.0 11.9 to 15.4 Outer edge of Packing: 2 500 pcs/reel flange Data Sheet PN10502EJ05V0DS 9

PS9121 <R> RECOMMENDED MOUNT PAD DIMENSIONS (UNIT: mm) 1.45 8 0. 7 2 1. 5.5 10 Data Sheet PN10502EJ05V0DS

PS9121 NOTES ON HANDLING 1. Recommended soldering conditions (1) Infrared reflow soldering • Peak reflow temperature 260°C or below (package surface temperature) • Time of peak reflow temperature 10 seconds or less • Time of temperature higher than 220°C 60 seconds or less • Time to preheat temperature from 120 to 180°C 120±30 s • Number of reflows Three • Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) Recommended Temperature Profile of Infrared Reflow C) T (˚ (htoe a1t0in sg) e ur 260˚C MAX. erat 220˚C p m to 60 s e T e c 180˚C a urf S 120˚C ge 120±30 s ka (preheating) c a P Time (s) (2) Wave soldering • Temperature 260°C or below (molten solder temperature) • Time 10 seconds or less • Preheating conditions 120°C or below (package surface temperature) • Number of times One (Allowed to be dipped in solder including plastic mold portion.) • Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (3) Soldering by Soldering Iron • Peak Temperature (lead part temperature) 350°C or below • Time (each pins) 3 seconds or less • Flux Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (a) Soldering of leads should be made at the point 1.5 to 2.0 mm from the root of the lead (b) Please be sure that the temperature of the package would not be heated over 100°C Data Sheet PN10502EJ05V0DS 11

PS9121 (4) Cautions • Fluxes Avoid removing the residual flux with freon-based and chlorine-based cleaning solvent. 2. Cautions regarding noise Be aware that when voltage is applied suddenly between the photocoupler’s input and output or between collector-emitters at startup, the output transistor may enter the on state, even if the voltage is within the absolute maximum ratings. USAGE CAUTIONS 1. Protect against static electricity when handling. 2. Avoid storage at a high temperature and high humidity. 12 Data Sheet PN10502EJ05V0DS

PS9121 <R> SPECIFICATION OF VDE MARKS LICENSE DOCUMENT Parameter Symbol Speck Unit Application classification (DIN EN 60664-1 VDE0110 Part 1) for rated line voltages ≤ 300 Vr.m.s. IV for rated line voltages ≤ 600 Vr.m.s. III Climatic test class (DIN EN 60664-1 VDE0110) 40/85/21 Dielectric strength maximum operating isolation voltage UIORM 707 Vpeak Test voltage (partial discharge test, procedure a for type test and random test) Upr 1 061 Vpeak Upr = 1.5 × UIORM, Pd < 5 pC Test voltage (partial discharge test, procedure b for all devices) Upr 1 326 Vpeak Upr = 1.875 × UIORM, Pd < 5 pC Highest permissible overvoltage UTR 6 000 Vpeak Degree of pollution (DIN EN 60664-1 VDE0110 Part 1) 2 Clearance distance >4.2 mm Creepage distance >4.2 mm Comparative tracking index (DIN IEC 112/VDE 0303 Part 1) CTI 175 Material group (DIN EN 60664-1 VDE0110 Part 1) III a Storage temperature range Tstg –55 to +125 °C Operating temperature range TA –40 to +85 °C Isolation resistance, minimum value VIO = 500 V dc at TA = 25°C Ris MIN. 1012 Ω VIO = 500 V dc at TA MAX. at least 100°C Ris MIN. 1011 Ω Safety maximum ratings (maximum permissible in case of fault, see thermal derating curve) Package temperature Tsi 150 °C Current (input current IF, Psi = 0) Isi 200 mA Power (output or total power dissipation) Psi 300 mW Isolation resistance VIO = 500 V dc at TA = Tsi Ris MIN. 109 Ω Data Sheet PN10502EJ05V0DS 13

PS9121 This product uses gallium arsenide (GaAs). Caution GaAs Products GaAs vapor and powder are hazardous to human health if inhaled or ingested, so please observe the following points. • Follow related laws and ordinances when disposing of the product. If there are no applicable laws and/or ordinances, dispose of the product as recommended below. 1. Commission a disposal company able to (with a license to) collect, transport and dispose of materials that contain arsenic and other such industrial waste materials. 2. Exclude the product from general industrial waste and household garbage, and ensure that the product is controlled (as industrial waste subject to special control) up until final disposal. • Do not burn, destroy, cut, crush, or chemically dissolve the product. • Do not lick the product or in any way allow it to enter the mouth.

NOTICE 1. Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples. You are fully responsible for the incorporation of these circuits, software, and information in the design of your equipment. California Eastern Laboratories and Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits, software, or information. 2. California Eastern Laboratories has used reasonable care in preparing the information included in this document, but California Eastern Laboratories does not warrant that such information is error free. California Eastern Laboratories and Renesas Electronics assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein. 3. California Eastern Laboratories and Renesas Electronics do not assume any liability for infringement of patents, copyrights, or other intellectual property rights of third parties by or arising from the use of Renesas Electronics products or technical information described in this document. No license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of California Eastern Laboratories or Renesas Electronics or others. 4. You should not alter, modify, copy, or otherwise misappropriate any Renesas Electronics product, whether in whole or in part. California Eastern Laboratories and Renesas Electronics assume no responsibility for any losses incurred by you or third parties arising from such alteration, modification, copy or otherwise misappropriation of Renesas Electronics product. 5. Renesas Electronics products are classified according to the following two quality grades: “Standard” and “High Quality”. The recommended applications for each Renesas Electronics product depends on the product’s quality grade, as indicated below. “Standard”: Computers; office equipment; communications equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools; personal electronic equipment; and industrial robots etc. “High Quality”: Transportation equipment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anti-crime systems; and safety equipment etc. Renesas Electronics products are neither intended nor authorized for use in products or systems that may pose a direct threat to human life or bodily injury (artificial life support devices or systems, surgical implantations etc.), or may cause serious property damages (nuclear reactor control systems, military equipment etc.). You must check the quality grade of each Renesas Electronics product before using it in a particular application. You may not use any Renesas Electronics product for any application for which it is not intended. California Eastern Laboratories and Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for which the product is not intended by California Eastern Laboratories or Renesas Electronics. 6. You should use the Renesas Electronics products described in this document within the range specified by California Eastern Laboratories, especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. California Eastern Laboratories shall have no liability for malfunctions or damages arising out of the use of Renesas Electronics products beyond such specified ranges. 7. Although Renesas Electronics endeavors to improve the quality and reliability of its products, semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Further, Renesas Electronics products are not subject to radiation resistance design. Please be sure to implement safety measures to guard them against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas Electronics product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or systems manufactured by you. 8. Please contact a California Eastern Laboratories sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product. Please use Renesas Electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. California Eastern Laboratories and Renesas Electronics assume no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations. 9. Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable domestic or foreign laws or regulations. You should not use Renesas Electronics products or technology described in this document for any purpose relating to military applications or use by the military, including but not limited to the development of weapons of mass destruction. When exporting the Renesas Electronics products or technology described in this document, you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and regulations. 10. It is the responsibility of the buyer or distributor of California Eastern Laboratories, who distributes, disposes of, or otherwise places the Renesas Electronics product with a third party, to notify such third party in advance of the contents and conditions set forth in this document, California Eastern Laboratories and Renesas Electronics assume no responsibility for any losses incurred by you or third parties as a result of unauthorized use of Renesas Electronics products. 11. This document may not be reproduced or duplicated in any form, in whole or in part, without prior written consent of California Eastern Laboratories. 12. Please contact a California Eastern Laboratories sales office if you have any questions regarding the information contained in this document or Renesas Electronics products, or if you have any other inquiries. NOTE 1: “Renesas Electronics” as used in this document means Renesas Electronics Corporation and also includes its majority-owned subsidiaries. NOTE 2: “Renesas Electronics product(s)” means any product developed or manufactured by or for Renesas Electronics. NOTE 3: Products and product information are subject to change without notice. CEL Headquarters • 4590 Patrick Henry Drive, Santa Clara, CA 95054 • Phone (408) 919-2500 • www.cel.com For a complete list of sales offices, representatives and distributors, Please visit our website: www.cel.com/contactus