Ultra-low ohmic jumper chip resistors PMR series - jumper type - Datasheet Features ● 1)Metallic resistive element utilized for extremely low conduction resistance. (0.5mΩMax.) 2)High current capability. 3)Superior strength against overcurrent and pulse loads. 4)Completely Pb free product. 5)Corresponds to AEC-Q200. But PMR01 is preparing. 6)ROHM resistors have obtained ISO9001 / ISO / TS16949 certification. Products list ● Temperature Size Rated current Part No. Resistance range (mm) (inch) (A) (℃) PMR01 1005 0402 20.0 0.5mΩ MAX． -55 ～ +155 PMR03 1608 0603 22.4 0.5mΩ MAX． -55 ～ +155 PMR10 2012 0805 31.6 0.5mΩ MAX． -55 ～ +155 PMR18 3216 1206 38.7 0.5mΩ MAX． -55 ～ +155 PMR25 3225 1210 44.7 0.5mΩ MAX． -55 ～ +155 PMR50 5025 2010 50.0 0.5mΩ MAX． -55 ～ +155 PMR100 6432 2512 63.2 0.5mΩ MAX． -55 ～ +155 *Design and specifications are subject to change without notice. Carefully check the specification sheet supplied with the product before using or ordering it. Part number description ●● P M R 2 5 H Z P J 0 0 0 Part No. Size (mm [inch]) Packaging specifications code Resistance Nominal resistance PMR 01 (1005 [0402]) Packaging Quantity tolerance Resistance code,3digits. Part No. Code (Ultra-low 03 (1608 [0603]) specifications / Reel J (Max. 0.5mΩ) ohmic jumper chip resistors) 10 (2012 [0805]) PMR01 ZZP Embossed tape 10,000 18 (3216 [1206]) (2mm pitch) 25 (3225 [1210]) Paper tape PMR03 EZP 5000 50 (5025 [2010]) (4mm pitch) 100 (6432 [2512]) Paper tape PMR10 EZP 5,000 (4mm pitch) Paper tape PMR18 EZP 5,000 (4mm pitch) Embossed tape PMR25 HZP 2,000 (4mm pitch) Embossed tape PMR50 HZP 2,000 (4mm pitch) Embossed tape PMR100 HZP 2,000 (4mm pitch) www.rohm.com 1/4 © 2016 ROHM Co., Ltd. All rights reserved. 2017.05 - Rev.G

PMR series - jumper type - Datasheet Chip resistor dimensions and markings ● ■■PMR 01 / 03 / 10 / 18 ■■PMR 25 / 50 / 100 <Marking method> 0000 (4 digits) (Unit:mm) Marking Part No. (mm) (inch) L W t a b c existence PMR01 1005 0402 1.00±0.05 0.50±0.05 0.25±0.10 ― 0.3±0.10 ― No PMR03 1608 0603 1.60±0.15 0.80±0.15 0.25±0.10 ― 0.35±0.15 ― No +0.15 PMR10 2012 0805 2.00±0.15 1.10 0.32±0.15 ― 0.55±0.25 ― Yes -0.05 PMR18 3216 1206 3.20±0.15 1.60±0.15 0.32±0.10 ― 0.90±0.25 ― Yes PMR25 3225 1210 3.20±0.20 2.50±0.15 0.32±0.15 ― 0.90±0.20 1.95±0.20 Yes PMR50 5025 2010 5.00±0.20 2.50±0.20 0.32±0.15 0.50±0.20 1.40±0.20 1.95±0.20 Yes PMR100 6432 2512 6.40±0.25 3.20±0.25 0.32±0.15 0.50±0.25 1.70±0.25 2.65±0.25 Yes Land pattern example ● (Unit:mm) Dimensions A B C D Part No. PMR01 0.5 1.8 0.5 0.65 PMR03 0.5 2.5 0.9 1.0 PMR10 0.8 3.4 1.3 1.3 PMR18 1.0 4.0 1.8 1.5 PMR25 1.0 4.0 2.8 1.5 PMR50 1.8 6.0 2.8 2.1 PMR100 2.4 7.6 3.8 2.6 www.rohm.com 2/4 © 2016 ROHM Co., Ltd. All rights reserved. 2017.05 - Rev.G

PMR series - jumper type - Datasheet Derating curve ● When the ambient temperature exceeds 70°C, power dissipation must be adjusted according to the derating curves below. ■RMR 01 / 03 / 10 / 18 / 25 / 50 / 100 Characteristics ● Guaranteed value Test items Test conditions Resistor type 20℃ Measuring method : Measure Bottom termination by 4 proves. Resistance MAX．0.5mΩ Variation of resistance MAX. 0.5mΩ Measurement：+25/-55, +25/+125℃ with temperature Overload MAX. 0.5mΩ Rated current×2.5, 2s A new uniform coating of minimum Rosin-ethanol solution25% (Wweight) of 95% of the surface being Solderability Soldering condition：245±5℃ immersed and no soldering Duration of immersion：2.0±0.5s damage. Resistance to MAX. 0.5mΩ Soldering condition：260±5℃ soldering heat No remarkable abnormality on the appearance. Duration of immersion：10±1s Rapid change of MAX. 0.5mΩ Test temp：-55℃～+125℃ 5cycle temperature 40℃，93％(Relative humidity) Damp heat, steady state MAX. 0.5mΩ Test time：1,000h 70℃,Rated current Endurance at 70℃ MAX. 0.5mΩ 1.5h:ON－0.5h:OFF Test time：1,000h 155℃ Endurance MAX. 0.5mΩ Test time：1,000h 23±5℃ Immersion cleaning, 5±0.5min Resistance to solvent MAX. 0.5mΩ Solvent: 2-propanol Bend strength of Without open. - the end face plating Compliance Standard(s) : IEC60115-8 JISC 5201-8 www.rohm.com 3/4 © 2016 ROHM Co., Ltd. All rights reserved. 2017.05 - Rev.G

PMR series - jumper type - Datasheet Tape dimensions ● ■Paper tape (Unit : mm) Part No. W F E A0 B0 PMR03 8.0±0.1 3.5±0.05 1.75±0.1 0.68±0.03 1.12±0.03 PMR10 8.0±0.3 3.5±0.05 1.75±0.1 0.95±0.1 1.75±0.1 +0.2 +0.2 PMR18 8.0±0.3 3.5±0.05 1.75±0.1 1.65 2.3 -0.1 -0.1 Part No. D0 P0 P1 P2 T2 +0.1 PMR03 Φ1.5 4.0±0.05 2.0±0.05 2.0±0.05 MAX1.1 0 +0.1 PMR10 Φ1.5 4.0±0.1 4.0±0.1 2.0±0.05 MAX1.1 0 +0.1 PMR18 Φ1.5 4.0±0.1 4.0±0.1 2.0±0.05 MAX1.1 0 ■Embossed tape (Unit : mm) Part No. W F E A0 B0 +0.1 +0.15 PMR01 8.0±0.3 3.5±0.05 1.75±0.1 1.95 3.5 -0.05 -0.05 PMR25 8.0±0.3 3.5±0.05 1.75±0.1 3.0±0.1 3.5±0.1 PMR50 12.0±0.3 5.5±0.05 1.75±0.1 2.9±0.2 5.3±0.2 PMR100 12.0±0.3 5.5±0.05 1.75±0.1 3.5±0.2 6.7±0.2 Part No. D0 P0 P1 P2 K +0.1 PMR01 Φ1.5 4.0±0.1 4.0±0.1 2.0±0.05 MAX1.1 0 +0.1 PMR25 Φ1.5 4.0±0.1 4.0±0.1 2.0±0.05 MAX1.1 0 +0.1 PMR50 Φ1.5 4.0±0.1 4.0±0.1 2.0±0.05 MAX1.1 0 +0.1 PMR100 Φ1.5 4.0±0.1 4.0±0.1 2.0±0.05 MAX1.1 0 ●Reel dimensions (Unit : mm) Part No. A B C D PMR01 PMR03 +1.0 PMR10 9 0 +1 0 PMR18 Φ180 Φ60 Φ13±0.2 -1.5 0 PMR25 PMR50 +1.0 13 PMR100 0 www.rohm.com 4/4 © 2016 ROHM Co., Ltd. All rights reserved. 2017.05 - Rev.G

Notice Precaution on using ROHM Products 1. Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment, OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment (Note 1), transport equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific Applications. (Note1) Medical Equipment Classification of the Specific Applications JAPAN USA EU CHINA CLASSⅢ CLASSⅡb CLASSⅢ CLASSⅢ CLASSⅣ CLASSⅢ 2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which a failure or malfunction of our Products may cause. The following are examples of safety measures: [a] Installation of protection circuits or other protective devices to improve system safety [b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. Our Products are designed and manufactured for use under standard conditions and not under any special or extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our Products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents [b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust [c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves [e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items [f] Sealing or coating our Products with resin or other coating materials [g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] Use of the Products in places subject to dew condensation 4. The Products are not subject to radiation-proof design. 5. Please verify and confirm characteristics of the final or mounted products in using the Products. 6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied, confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect product performance and reliability. 7. De-rate Power Dissipation depending on ambient temperature. When used in sealed area, confirm that it is the use in the range that does not exceed the maximum junction temperature. 8. Confirm that operation temperature is within the specified range described in the product specification. 9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in this document. Precaution for Mounting / Circuit board design 1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product performance and reliability. 2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products, please consult with the ROHM representative in advance. For details, please refer to ROHM Mounting specification Notice-PGA-E Rev.003 © 2015 ROHM Co., Ltd. All rights reserved.

Precautions Regarding Application Examples and External Circuits 1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the characteristics of the Products and external components, including transient characteristics, as well as static characteristics. 2. You agree that application notes, reference designs, and associated data and information contained in this document are presented only as guidance for Products use. Therefore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. Precaution for Electrostatic This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron, isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control). Precaution for Storage / Transportation 1. Product performance and soldered connections may deteriorate if the Products are stored in the places where: [a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2 [b] the temperature or humidity exceeds those recommended by ROHM [c] the Products are exposed to direct sunshine or condensation [d] the Products are exposed to high Electrostatic 2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is exceeding the recommended storage time period. 3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of which storage time is exceeding the recommended storage time period. Precaution for Product Label A two-dimensional barcode printed on ROHM Products label is for ROHM’s internal use only. Precaution for Disposition When disposing Products please dispose them properly using an authorized industry waste company. Precaution for Foreign Exchange and Foreign Trade act Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign trade act, please consult with ROHM in case of export. Precaution Regarding Intellectual Property Rights 1. All information and data including but not limited to application example contained in this document is for reference only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. 2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the Products with other articles such as components, circuits, systems or external equipment (including software). 3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to manufacture or sell products containing the Products, subject to the terms and conditions herein. Other Precaution 1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM. 2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of ROHM. 3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the Products or this document for any military purposes, including but not limited to, the development of mass-destruction weapons. 4. The proper names of companies or products described in this document are trademarks or registered trademarks of ROHM, its affiliated companies or third parties. Notice-PGA-E Rev.003 © 2015 ROHM Co., Ltd. All rights reserved.

DDaattaasshheeeett General Precaution 1. Before you use our Products, you are requested to carefully read this document and fully understand its contents. ROHM shall not be in any way responsible or liable for failure, malfunction or accident arising from the use of a ny ROHM’s Products against warning, caution or note contained in this document. 2. All information contained in this document is current as of the issuing date and subj ect to change without any prior notice. Before purchasing or using ROHM’s Products, please confirm the latest information with a ROHM sale s representative. 3. The information contained in this document is provided on an “as is” basis and ROHM does not warrant that all information contained in this document is accurate an d/or error-free. ROHM shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties resulting from inaccuracy or errors of or concerning such information. Notice – WE Rev.001 © 2015 ROHM Co., Ltd. All rights reserved.

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: R OHM Semiconductor: PMR100HZPFV1L00 PMR100HZPFV3L00 PMR18EZPFV4L00 PMR10EZPFV3L00 PMR50HZPFU10L0 PMR10EZPJ000 PMR01ZZPJ000 PMR10EZPFU8L00 PMR18EZPFU9L00 PMR18EZPFU6L00 PMR03EZPFU10L0 PMR03EZPJ000 PMR18EZPJ000 PMR50HZPFV4L00 PMR18EZPFU7L00 PMR10EZPFU5L00 PMR50HZPFV3L00 PMR10EZPFU7L00 PMR18EZPFU5L00 PMR25HZPFV1L00 PMR10EZPFU6L00 PMR18EZPFU8L00 PMR10EZPFU9L00 PMR50HZPFU5L00 PMR50HZPFU9L00 PMR50HZPFV2L00 PMR50HZPFU7L00 PMR100HZPFV2L00 PMR18EZPFV3L00 PMR25HZPFU5L00 PMR50HZPFV1L00 PMR100HZPFU10L0 PMR50HZPFU6L00 PMR18EZPFV2L00 PMR100HZPFU5L00 PMR100HZPFU7L00 PMR18EZPFU10L0 PMR10EZPFU10L0 PMR50HZPFU8L00 PMR100HZPFV4L00 PMR100HZPFU6L00 PMR10EZPFV2L00 PMR100HZPFU8L00 PMR10EZPJU10L PMR10EZPJU8L0 PMR100HZPJU5L0 PMR100HZPJU8L0 PMR18EZPJU5L0 PMR50HZPJU10L PMR25HZPJV3L0 PMR25HZPFV2L00 PMR10EZPFV4L00 PMR18EZPJU10L PMR25HZPFV3L00 PMR25HZPFV4L00 PMR25HZPJV1L0 PMR10EZPJU5L0 PMR50HZPJU8L0 PMR100HZPJU10L PMR18EZPJU6L0 PMR100HZPFU9L00 PMR25HZPJV2L0 PMR100HZPJV1L0 PMR18EZPJU7L0 PMR18EZPJV3L0 PMR18EZPJV4L0 PMR50HZPJV3L0 PMR100HZPJV2L0 PMR10EZPJV2L0 PMR25HZPJU5L0 PMR18EZPJV2L0 PMR10EZPJV3L0