PIC24FV32KA304 FAMILY 20/28/44/48-Pin, General Purpose, 16-Bit Flash Microcontrollers with XLP Technology Power Management Modes Peripheral Features • Run – CPU, Flash, SRAM and Peripherals On • Hardware Real-Time Clock and Calendar (RTCC): • Doze – CPU Clock Runs Slower than Peripherals - Provides clock, calendar and alarm functions • Idle – CPU Off, Flash, SRAM and Peripherals On - Can run in Deep Sleep mode • Sleep – CPU, Flash and Peripherals Off, and - Can use 50/60 Hz power line input as clock SRAM On source • Deep Sleep – CPU, Flash, SRAM and • Programmable 32-Bit Cyclic Redundancy Check Most Peripherals Off; Multiple Autonomous (CRC) Wake-up Sources • Multiple Serial Communication modules: • Low-Power Consumption: - Two 3/4-wire SPI modules - Run mode currents down to 8 μA, typical - Two I2C modules with multi-master/slave support - Idle mode currents down to 2.2 μA, typical - Two UART modules, supporting RS-485, - Deep Sleep mode currents down to 20 nA, RS-232, LIN/J2602, IrDA® typical • Five 16-Bit Timers/Counters with Programmable - Real-Time Clock/Calendar currents down to Prescaler: 700 nA, 32 kHz, 1.8V - Can be paired as 32-bit timers/counters - Watchdog Timer is 500 nA, 1.8V typical • Three 16-Bit Capture Inputs with Dedicated Timers High-Performance CPU • Three 16-Bit Compare/PWM Outputs with • Modified Harvard Architecture Dedicated Timers • Up to 16 MIPS Operation @ 32 MHz • Configurable Open-Drain Outputs on Digital I/O Pins • 8 MHz Internal Oscillator with 4x PLL Option and Multiple Divide Options • Up to Three External Interrupt Sources • 17-Bit by 17-Bit Single-Cycle Hardware Multiplier • 32-Bit by 16-Bit Hardware Divider, 16-Bit x 16-Bit Working Register Array • C Compiler Optimized Instruction Set Architecture  2011-2017 Microchip Technology Inc. DS30009995E-page 1

PIC24FV32KA304 FAMILY Analog Features Special Microcontroller Features • 12-Bit, Up to 16-Channel Analog-to-Digital • Wide Operating Voltage Range: Converter: - 1.8V to 3.6V (PIC24F devices) - 100 ksps conversion rate - 2.0V to 5.5V (PIC24FV devices) - Conversion available during Sleep and Idle • Low-Power Wake-up Sources and Supervisors: - Auto-sampling, timer-based option for Sleep - Ultra Low-Power Wake-up (ULPWU) for Sleep/Deep Sleep and Idle modes - Low-Power Watchdog Timer (DSWDT) for - Wake on auto-compare option Deep Sleep • Dual Rail-to-Rail Analog Comparators with - Extreme Low-Power Brown-out Reset (DSBOR) for Programmable Input/Output Configuration Deep Sleep, LPBOR for all other modes • On-Chip Voltage Reference • System Frequency Range Declaration bits: • Internal Temperature Sensor - Declaring the frequency range optimizes the • Charge Time Measurement Unit (CTMU): current consumption. - Used for capacitance sensing, 16 channels • Standard Watchdog Timer (WDT) with On-Chip, Low-Power RC Oscillator for Reliable Operation - Time measurement, down to 200 ps resolution • Programmable High/Low-Voltage Detect (HLVD) • Standard Brown-out Reset (BOR) with - Delay/pulse generation, down to 1 ns 3 Programmable Trip Points that can be Disabled resolution in Sleep • High-Current Sink/Source (18 mA/18 mA) on All I/O Pins • Flash Program Memory: - Erase/write cycles: 10,000 minimum - 40 years’ data retention minimum • Data EEPROM: - Erase/write cycles: 100,000 minimum - 40 years’ data retention minimum • Fail-Safe Clock Monitor (FSCM) • Programmable Reference Clock Output • Self-Programmable under Software Control • In-Circuit Serial Programming™ (ICSP™) and In-Circuit Debug (ICD) via 2 Pins Memory M h) s PDIeCv2ic4eF Pins Flash Program(bytes) SRAM(bytes) EE Data(bytes) Timers16-Bit CaptureInput ompare/PWOutput UART w/®IrDA SPI 2IC 2-Bit A/D (c Comparator CTMU (ch) RTCC C 1 PIC24FV16KA301/ 20 16K 2K 512 5 3 3 2 2 2 12 3 12 Y PIC24F16KA301 PIC24FV32KA301/ 20 32K 2K 512 5 3 3 2 2 2 12 3 12 Y PIC24F32KA301 PIC24FV16KA302/ 28 16K 2K 512 5 3 3 2 2 2 13 3 13 Y PIC24F16KA302 PIC24FV32KA302/ 28 32K 2K 512 5 3 3 2 2 2 13 3 13 Y PIC24F32KA302 PIC24FV16KA304/ 44 16K 2K 512 5 3 3 2 2 2 16 3 16 Y PIC24F16KA304 PIC24FV32KA304/ 44 32K 2K 512 5 3 3 2 2 2 16 3 16 Y PIC24F32KA304 DS30009995E-page 2  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY Pin Diagrams 20-Pin SPDIP/SSOP/SOIC(1) MCLR/RA5 1 20 VDD RRRAAB010 234 A301A301111987 VRRSBBS1154 RB1 5 KK16 RB13 RRRRABAB3422 6789 24FVXX24FXX11115432 RRRRABBB6189 2or VCAP RA4 10 11 RB7 Pin Features Pin PIC24FVXXKA301 PIC24FXXKA301 1 MCLR/VPP/RA5 MCLR/VPP/RA5 2 PGEC2/VREF+/CVREF+/AN0/C3INC/SCK2/CN2/RA0 PGEC2/VREF+/CVREF+/AN0/C3INC/SCK2/CN2/RA0 3 PGED2/CVREF-/VREF-/AN1/SDO2/CN3/RA1 PGED2/CVREF-/VREF-/AN1/SDO2/CN3/RA1 4 PGED1/AN2/ULPWU/CTCMP/C1IND/C2INB/C3IND/U2TX/SDI2/ PGED1/AN2/ULPWU/CTCMP/C1IND/C2INB/C3IND/U2TX/SDI2/ OC2/CN4/RB0 OC2/CN4/RB0 5 PGEC1/AN3/C1INC/C2INA/U2RX/OC3/CTED12/CN5/RB1 PGEC1/AN3/C1INC/C2INA/U2RX/OC3/CTED12/CN5/RB1 6 AN4/SDA2/T5CK/T4CK/U1RX/CTED13/CN6/RB2 AN4/SDA2/T5CK/T4CK/U1RX/CTED13/CN6/RB2 7 OSCI/AN13/C1INB/C2IND/CLKI/CN30/RA2 OSCI/AN13/C1INB/C2IND/CLKI/CN30/RA2 8 OSCO/AN14/C1INA/C2INC/CLKO/CN29/RA3 OSCO/AN14/C1INA/C2INC/CLKO/CN29/RA3 9 PGED3/SOSCI/AN15/U2RTS/CN1/RB4 PGED3/SOSCI/AN15/U2RTS/CN1/RB4 10 PGEC3/SOSCO/SCLKI/U2CTS/CN0/RA4 PGEC3/SOSCO/SCLKI/U2CTS/CN0/RA4 11 U1TX/C2OUT/OC1/IC1/CTED1/INT0/CN23/RB7 U1TX/INT0/CN23/RB7 12 SCL1/U1CTS/C3OUT/CTED10/CN22/RB8 SCL1/U1CTS/C3OUT/CTED10/CN22/RB8 13 SDA1/T1CK/U1RTS/IC2/CTED4/CN21/RB9 SDA1/T1CK/U1RTS/IC2/CTED4/CN21/RB9 14 VCAP C2OUT/OC1/IC1/CTED1/INT2/CN8/RA6 15 AN12/HLVDIN/SCK1/SS2/IC3/CTED2/INT2/CN14/RB12 AN12/HLVDIN/SCK1/SS2/IC3/CTED2/CN14/RB12 16 AN11/SDO1/OCFB/CTPLS/CN13/RB13 AN11/SDO1/OCFB/CTPLS/CN13/RB13 17 CVREF/AN10/C3INB/RTCC/SDI1/C1OUT/OCFA/CTED5/INT1/ CVREF/AN10/C3INB/RTCC/SDI1/C1OUT/OCFA/CTED5/INT1/ CN12/RB14 CN12/RB14 18 AN9/C3INA/SCL2/T3CK/T2CK/REFO/SS1/CTED6/CN11/RB15 AN9/C3INA/SCL2/T3CK/T2CK/REFO/SS1/CTED6/CN11/RB15 19 VSS/AVSS VSS/AVSS 20 VDD/AVDD VDD/AVDD Legend: Pin numbers in bold indicate pin function differences between PIC24FV and PIC24F devices. Note 1: PIC24F32KA304 device pins have a maximum voltage of 3.6V and are not 5V tolerant.  2011-2017 Microchip Technology Inc. DS30009995E-page 3

PIC24FV32KA304 FAMILY Pin Diagrams 28-Pin SPDIP/SSOP/SOIC(2) MCLR/RA5 1 28 VDD RA0 2 27 Vss RRRABB101 345 A302A302222654 RRRBBB111543 RRRRVAABBS3232S 678910C24FVXXKC24FXXK2222132109 RRRRRABBAB611711 20or VCAP RB4 11 PIPI18 RB9 RA4 12 17 RB8 VDD 13 16 RB7 RB5 14 15 RB6 Pin Features Pin PIC24FVXXKA302 PIC24FXXKA302 1 MCLR/VPP/RA5 MCLR/VPP/RA5 2 VREF+/CVREF+/AN0/C3INC/CTED1/CN2/RA0 VREF+/CVREF+/AN0/C3INC/CTED1/CN2/RA0 3 CVREF-/VREF-/AN1/CN3/RA1 CVREF-/VREF-/AN1/CN3/RA1 4 PGED1/AN2/ULPWU/CTCMP/C1IND/C2INB/C3IND/U2TX/CN4/RB0 PGED1/AN2/ULPWU/CTCMP/C1IND/C2INB/C3IND/U2TX/CN4/RB0 5 PGEC1/AN3/C1INC/C2INA/U2RX/CTED12/CN5/RB1 PGEC1/AN3/C1INC/C2INA/U2RX/CN5/RB1 6 AN4/C1INB/C2IND/SDA2/T5CK/T4CK/U1RX/CTED13/CN6/RB2 AN4/C1INB/C2IND/SDA2/T5CK/T4CK/U1RX/CTED13/CN6/RB2 7 AN5/C1INA/C2INC/SCL2/CN7/RB3 AN5/C1INA/C2INC/SCL2/CN7/RB3 8 VSS VSS 9 OSCI/AN13/CLKI/CN30/RA2 OSCI/AN13/CLKI/CN30/RA2 10 OSCO/AN14/CLKO/CN29/RA3 OSCO/AN14/CLKO/CN29/RA3 11 SOSCI/AN15/U2RTS/CN1/RB4 SOSCI/AN15/U2RTS/CN1/RB4 12 SOSCO/SCLKI/U2CTS/CN0/RA4 SOSCO/SCLKI/U2CTS/CN0/RA4 13 VDD VDD 14 PGED3/ASDA(1)/SCK2/CN27/RB5 PGED3/ASDA(1)/SCK2/CN27/RB5 15 PGEC3/ASCL(1)/SDO2/CN24/RB6 PGEC3/ASCL(1)/SDO2/CN24/RB6 16 U1TX/C2OUT/OC1/INT0/CN23/RB7 U1TX/INT0/CN23/RB7 17 SCL1/U1CTS/C3OUT/CTED10/CN22/RB8 SCL1/U1CTS/C3OUT/CTED10/CN22/RB8 18 SDA1/T1CK/U1RTS/IC2/CTED4/CN21/RB9 SDA1/T1CK/U1RTS/IC2/CTED4/CN21/RB9 19 SDI2/IC1/CTED3/CN9/RA7 SDI2/IC1/CTED3/CN9/RA7 20 VCAP C2OUT/OC1/CTED1/INT2/CN8/RA6 21 PGED2/SDI1/OC3/CTED11/CN16/RB10 PGED2/SDI1/OC3/CTED11/CN16/RB10 22 PGEC2/SCK1/OC2/CTED9/CN15/RB11 PGEC2/SCK1/OC2/CTED9/CN15/RB11 23 AN12/HLVDIN/SS2/IC3/CTED2/INT2/CN14/RB12 AN12/HLVDIN/SS2/IC3/CTED2/CN14/RB12 24 AN11/SDO1/OCFB/CTPLS/CN13/RB13 AN11/SDO1/OCFB/CTPLS/CN13/RB13 25 CVREF/AN10/C3INB/RTCC/C1OUT/OCFA/CTED5/INT1/CN12/RB14 CVREF/AN10/C3INB/RTCC/C1OUT/OCFA/CTED5/INT1/CN12/RB14 26 AN9/C3INA/T3CK/T2CK/REFO/SS1/CTED6/CN11/RB15 AN9/C3INA/T3CK/T2CK/REFO/SS1/CTED6/CN11/RB15 27 VSS/AVSS VSS/AVSS 28 VDD/AVDD VDD/AVDD Legend: Pin numbers in bold indicate pin function differences between PIC24FV and PIC24F devices. Note 1: Alternative multiplexing for SDA1 (ASDA1) and SCL1 (ASCL1) when the I2CSEL Configuration bit is set. 2: PIC24F32KA304 device pins have a maximum voltage of 3.6V and are not 5V tolerant. DS30009995E-page 4  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY Pin Diagrams 28-Pin QFN(1,3) 5 A R RA1RA0MCLR/VDDVSSRB15RB14 28272625242322 RB0 1 21 RB13 RB1 2 20 RB12 RB2 3 PIC24FVXXKA302 19 RB11 RB3 4 PIC24FXXKA302 18 RB10 VSS 5 17 RA6 or VCAP RA2 6 16 RA7 RA3 7 15 RB9 8 9 1011121314 44D5678 BADBBBB RRVRRRR Pin Features Pin PIC24FVXXKA302 PIC24FXXKA302 1 PGED1/AN2/ULPWU/CTCMP/C1IND/C2INB/C3IND/U2TX/CN4/RB0 PGED1/AN2/ULPWU/CTCMP/C1IND/C2INB/C3IND/U2TX/CN4/RB0 2 PGEC1/AN3/C1INC/C2INA/U2RX/CTED12/CN5/RB1 PGEC1/AN3/C1INC/C2INA/U2RX/CTED12/CN5/RB1 3 AN4/C1INB/C2IND/SDA2/T5CK/T4CK/U1RX/CTED13/CN6/RB2 AN4/C1INB/C2IND/SDA2/T5CK/T4CK/U1RX/CTED13/CN6/RB2 4 AN5/C1INA/C2INC/SCL2/CN7/RB3 AN5/C1INA/C2INC/SCL2/CN7/RB3 5 VSS VSS 6 OSCI/AN13/CLKI/CN30/RA2 OSCI/AN13/CLKI/CN30/RA2 7 OSCO/AN14/CLKO/CN29/RA3 OSCO/AN14/CLKO/CN29/RA3 8 SOSCI/AN15/U2RTS/CN1/RB4 SOSCI/AN15/U2RTS/CN1/RB4 9 SOSCO/SCLKI/U2CTS/CN0/RA4 SOSCO/SCLKI/U2CTS/CN0/RA4 10 VDD VDD 11 PGED3/ASDA1(2)/SCK2/CN27/RB5 PGED3/ASDA1(2)/SCK2/CN27/RB5 12 PGEC3/ASCL1(2)/SDO2/CN24/RB6 PGEC3/ASCL1(2)/SDO2/CN24/RB6 13 U1TX/C2OUT/OC1/INT0/CN23/RB7 U1TX/INT0/CN23/RB7 14 SCL1/U1CTS/C3OUT/CTED10/CN22/RB8 SCL1/U1CTS/C3OUT/CTED10/CN22/RB8 15 SDA1/T1CK/U1RTS/IC2/CTED4/CN21/RB9 SDA1/T1CK/U1RTS/IC2/CTED4/CN21/RB9 16 SDI2/IC1/CTED3/CN9/RA7 SDI2/IC1/CTED3/CN9/RA7 17 VCAP C2OUT/OC1/CTED1/INT2/CN8/RA6 18 PGED2/SDI1/OC3/CTED11/CN16/RB10 PGED2/SDI1/OC3/CTED11/CN16/RB10 19 PGEC2/SCK1/OC2/CTED9/CN15/RB11 PGEC2/SCK1/OC2/CTED9/CN15/RB11 20 AN12/HLVDIN/SS2/IC3/CTED2/INT2/CN14/RB12 AN12/HLVDIN/SS2/IC3/CTED2/CN14/RB12 21 AN11/SDO1/OCFB/CTPLS/CN13/RB13 AN11/SDO1/OCFB/CTPLS/CN13/RB13 22 CVREF/AN10/C3INB/RTCC/C1OUT/OCFA/CTED5/INT1/CN12/RB14 CVREF/AN10/C3INB/RTCC/C1OUT/OCFA/CTED5/INT1/CN12/RB14 23 AN9/C3INA/T3CK/T2CK/REFO/SS1/CTED6/CN11/RB15 AN9/C3INA/T3CK/T2CK/REFO/SS1/CTED6/CN11/RB15 24 VSS/AVSS VSS/AVSS 25 VDD/AVDD VDD/AVDD 26 MCLR/VPP/RA5 MCLR/VPP/RA5 27 VREF+/CVREF+/AN0/C3INC/CTED1/CN2/RA0 VREF+/CVREF+/AN0/C3INC/CN2/RA0 28 CVREF-/VREF-/AN1/CN3/RA1 CVREF-/VREF-/AN1/CN3/RA1 Legend: Pin numbers in bold indicate pin function differences between PIC24FV and PIC24F devices. Note 1: Exposed pad on underside of device is connected to VSS. 2: Alternative multiplexing for SDA1 (ASDA1) and SCL1 (ASCL1) when the I2CSEL Configuration bit is set. 3: PIC24F32KA304 device pins have a maximum voltage of 3.6V and are not 5V tolerant.  2011-2017 Microchip Technology Inc. DS30009995E-page 5

PIC24FV32KA304 FAMILY Pin Diagrams Pin Features Pin 44-Pin TQFP/QFN(1,3) PIC24FVXXKA304 PIC24FXXKA304 1 SDA1/T1CK/U1RTS/CTED4/CN21/ SDA1/T1CK/U1RTS/CTED4/CN21/ RB9 RB9 2 U1RX/CN18/RC6 U1RX/CN18/RC6 3 U1TX/CN17/RC7 U1TX/CN17/RC7 B8B7B6B5DDSSC5C4C3A9A4 4 OC2/CN20/RC8 OC2/CN20/RC8 RRRRVVRRRRR 5 IC2/CTED7/CN19/RC9 IC2/CTED7/CN19/RC9 43210987654 RB9 1 4444433333333 RB4 6 IC1/CTED3/CN9/RA7 IC1/CTED3/CN9/RA7 RC6 2 32 RA8 7 VCAP C2OUT/OC1/CTED1/INT2/CN8/RA6 RC7 3 31 RA3 8 PGED2/SDI1/CTED11/CN16/RB10 PGED2/SDI1/CTED11/CN16/RB10 RC8 4 30 RA2 RC9 5 PIC24FVXXKA304 29 Vss 9 PGEC2/SCK1/CTED9/CN15/RB11 PGEC2/SCK1/CTED9/CN15/RB11 RA7 6 PIC24FXXKA304 28 VDD 10 AN12/HLVDIN/CTED2/INT2/CN14/ AN12/HLVDIN/CTED2/CN14/RB12 RA6 or VCAP 7 27 RC2 RB12 RB10 8 26 RC1 11 AN11/SDO1/CTPLS/CN13/RB13 AN11/SDO1/CTPLS/CN13/RB13 RB11 9 25 RC0 RB12 10 24 RB3 12 OC3/CN35/RA10 OC3/CN35/RA10 RB13 112345678901223 RB2 13 IC3/CTED8/CN36/RA11 IC3/CTED8/CN36/RA11 11111111222 14 CVREF/AN10/C3INB/RTCC/ CVREF/AN10/C3INB/RTCC/ 0145SD50101 1111SDAAABB C1OUT/OCFA/CTED5/INT1/CN12/ C1OUT/OCFA/CTED5/INT1/CN12/ RARARBRBVVR/RRRRR RB14 RB14 CL 15 AN9/C3INA/T3CK/T2CK/REFO/ AN9/C3INA/T3CK/T2CK/REFO/ M SS1/CTED6/CN11/RB15 SS1/CTED6/CN11/RB15 16 VSS/AVSS VSS/AVSS 17 VDD/AVDD VDD/AVDD 18 MCLR/VPP/RA5 MCLR/VPP/RA5 19 VREF+/CVREF+/AN0/C3INC/ VREF+/CVREF+/AN0/C3INC/CN2/ CTED1/CN2/RA0 RA0 20 CVREF-/VREF-/AN1/CN3/RA1 CVREF-/VREF-/AN1/CN3/RA1 21 PGED1/AN2/ULPWU/CTCMP/ PGED1/AN2/ULPWU/CTCMP/ C1IND/C2INB/C3IND/U2TX/CN4/ C1IND/C2INB/C3IND/U2TX/CN4/ RB0 RB0 22 PGEC1/AN3/C1INC/C2INA/U2RX/ PGEC1/AN3/C1INC/C2INA/U2RX/ CTED12/CN5/RB1 CTED12/CN5/RB1 23 AN4/C1INB/C2IND/SDA2/T5CK/ AN4/C1INB/C2IND/SDA2/T5CK/ T4CK/CTED13/CN6/RB2 T4CK/CTED13/CN6/RB2 24 AN5/C1INA/C2INC/SCL2/CN7/RB3 AN5/C1INA/C2INC/SCL2/CN7/RB3 25 AN6/CN32/RC0 AN6/CN32/RC0 26 AN7/CN31/RC1 AN7/CN31/RC1 27 AN8/CN10/RC2 AN8/CN10/RC2 28 VDD VDD 29 VSS VSS 30 OSCI/AN13/CLKI/CN30/RA2 OSCI/AN13/CLKI/CN30/RA2 31 OSCO/AN14/CLKO/CN29/RA3 OSCO/AN14/CLKO/CN29/RA3 32 OCFB/CN33/RA8 OCFB/CN33/RA8 33 SOSCI/AN15/U2RTS/CN1/RB4 SOSCI/AN15/U2RTS/CN1/RB4 34 SOSCO/SCLKI/U2CTS/CN0/RA4 SOSCO/SCLKI/U2CTS/CN0/RA4 Legend: Pin numbers in bold indicate pin func- tion differences between PIC24FV and 35 SS2/CN34/RA9 SS2/CN34/RA9 PIC24F devices. 36 SDI2/CN28/RC3 SDI2/CN28/RC3 Note 1: Exposed pad on underside of device is 37 SDO2/CN25/RC4 SDO2/CN25/RC4 connected to VSS. 38 SCK2/CN26/RC5 SCK2/CN26/RC5 2: Alternative multiplexing for SDA1 39 VSS VSS (ASDA1) and SCL1 (ASCL1) when the 40 VDD VDD I2CSEL Configuration bit is set. 41 PGED3/ASDA1(2)/CN27/RB5 PGED3/ASDA1(2)/CN27/RB5 3: PIC24F32KA304 device pins have a 42 PGEC3/ASCL1(2)/CN24/RB6 PGEC3/ASCL1(2)/CN24/RB6 maximum voltage of 3.6V and are not 43 C2OUT/OC1/INT0/CN23/RB7 INT0/CN23/RB7 5V tolerant. 44 SCL1/U1CTS/C3OUT/CTED10/ SCL1/U1CTS/C3OUT/CTED10/ CN22/RB8 CN22/RB8 DS30009995E-page 6  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY Pin Diagrams Pin Features 48-Pin UQFN(1,3) Pin PIC24FVXXKA304 PIC24FXXKA304 1 SDA1/T1CK/U1RTS/CTED4/CN21/RB9 SDA1/T1CK/U1RTS/CTED4/CN21/ RB9 2 U1RX/CN18/RC6 U1RX/CN18/RC6 3 U1TX/CN17/RC7 U1TX/CN17/RC7 B8R7RB6RB5BRC/NVDDVSS5RC4CR3CRA9R4RA 4 OC2/CN20/RC8 OC2/CN20/RC8 5 IC2/CTED7/CN19/RC9 IC2/CTED7/CN19/RC9 876543210987 RB9 1 44444444433336 RB4 6 IC1/CTED3/CN9/RA7 IC1/CTED3/CN9/RA7 RRCC67 23 3354 RRAA83 7 VCAP C20UT/OC1/CTED1/INT2CN8/RA6 RC8 4 33 RA2 8 N/C N/C RC9 5 32 N/C 9 PGED2/SDI1/CTED11/CN16/RB10 PGED2/SDI1/CTED11/CN16/RB10 RA7 6 PIC24FVXXKA304 31 VSS RA6 or VCAP 7 PIC24FXXKA304 30 VDD 10 PGEC2/SCK1/CTED9/CN15/RB11 PGEC2/SCK1/CTED9/CN15/RB11 N/C 8 29 RC2 11 AN12/HLVDIN/CTED2/INT2/CN14/RB12 AN12/HLVDIN/CTED2/CN14/RB12 RB10 9 28 RC1 RB11 10 27 RC0 12 AN11/SDO1/CTPLS/CN13/RB13 AN11/SDO1/CTPLS/CN13/RB13 RB12 11 26 RB3 13 OC3/CN35/RA10 OC3/CN35/RA10 RB13 12 25 RB2 14 IC3/CTED8/CN36/RA11 IC3/CTED8/CN36/RA11 345678901234 111111122222 15 CVREF/AN10/C3INB/RTCC/ CVREF/AN10/C3INB/RTCC/C1OUT/ 0145SD5C0101 C1OUT/OCFA/CTED5/INT1/CN12/RB14 OCFA/CTED5/INT1/CN12/RB14 1AR1RA1BRB1RVA/V SSSVA/VDDDRAR/LMCN/ARARBRBR 1167 AVSNSSS19///ACCVT3SEINSDA6/T/C3NC1K1//TR2BC1K5/REFO/ ASVNSSS19///ACCVT3SIENSDA6/T/C3NC1K1//TR2BC1K5/REFO/ 18 VDD/AVDD VDD/AVDD 19 MCLR/RA5 MCLR/RA5 20 N/C N/C 21 VREF+/CVREF+/AN0/C3INC/ VREF+/CVREF+/AN0/C3INC/CN2/ CTED1/CN2/RA0 RA0 22 CVREF-/VREF-/AN1/CN3/RA1 CVREF-/VREF-/AN1/CN3/RA1 23 PGED1/AN2/ULPWU/CTCMP/C1IND/ PGED1/AN2/ULPWU/CTCMP/C1IND/ C2INB/C3IND/U2TX/CN4/RB0 C2INB/C3IND/U2TX/CN4/RB0 24 PGEC1/AN3/C1INC/C2INA/U2RX/ PGEC1/AN3/C1INC/C2INA/U2RX/ CTED12/CN5/RB1 CTED12/CN5/RB1 25 AN4/C1INB/C2IND/SDA2/T5CK/ AN4/C1INB/C2IND/SDA2/T5CK/ T4CK/CTED13/CN6/RB2 T4CK/CTED13/CN6/RB2 26 AN5/C1INA/C2INC/SCL2/CN7/RB3 AN5/C1INA/C2INC/SCL2/CN7/RB3 27 AN6/CN32/RC0 AN6/CN32/RC0 28 AN7/CN31/RC1 AN7/CN31/RC1 29 AN8/CN10/RC2 AN8/CN10/RC2 30 VDD VDD 31 VSS VSS 32 N/C N/C 33 OSCI/AN13/CLKI/CN30/RA2 OSCI/AN13/CLKI/CN30/RA2 34 OSCO/AN14/CLKO/CN29/RA3 OSCO/AN14/CLKO/CN29/RA3 35 OCFB/CN33/RA8 OCFB/CN33/RA8 36 SOSCI/AN15/U2RTS/CN1/RB4 SOSCI/AN15/U2RTS/CN1/RB4 37 SOSCO/SCLKI/U2CTS/CN0/RA4 SOSCO/SCLKI/U2CTS/CN0/RA4 38 SS2/CN34/RA9 SS2/CN34/RA9 Legend: Pin numbers in bold indicate pin function 39 SDI2/CN28/RC3 SDI2/CN28/RC3 differences between PIC24FV and PIC24F devices. 40 SDO2/CN25/RC4 SDO2/CN25/RC4 41 SCK2/CN26/RC5 SCK2/CN26/RC5 Note 1: Exposed pad on underside of device is connected to VSS. 42 VSS VSS 2: Alternative multiplexing for SDA1 43 VDD VDD (ASDA1) and SCL1 (ASCL1) when the 44 N/C N/C I2CSEL Configuration bit is set. 45 PGED3/ASDA1(2)/CN27/RB5 PGED3/ASDA1(2)/CN27/RB5 3: PIC24F32KA3XX device pins have a 46 PGEC3/ASCL1(2)/CN24/RB6 PGEC3/ASCL1(2)/CN24/RB6 maximum voltage of 3.6V and are not 5V 47 C2OUT/OC1/INT0/CN23/RB7 INT0/CN23/RB7 tolerant. 48 SCL1/U1CTS/C3OUT/CTED10/ SCL1/U1CTS/C3OUT/CTED10/ CN22/RB8 CN22/RB8  2011-2017 Microchip Technology Inc. DS30009995E-page 7

PIC24FV32KA304 FAMILY Table of Contents 1.0 Device Overview........................................................................................................................................................................11 2.0 Guidelines for Getting Started with 16-Bit Microcontrollers........................................................................................................23 3.0 CPU ...........................................................................................................................................................................................29 4.0 Memory Organization.................................................................................................................................................................35 5.0 Flash Program Memory..............................................................................................................................................................57 6.0 Data EEPROM Memory.............................................................................................................................................................63 7.0 Resets........................................................................................................................................................................................69 8.0 Interrupt Controller.....................................................................................................................................................................75 9.0 Oscillator Configuration............................................................................................................................................................115 10.0 Power-Saving Features............................................................................................................................................................125 11.0 I/O Ports...................................................................................................................................................................................135 12.0 Timer1 .....................................................................................................................................................................................139 13.0 Timer2/3 and Timer4/5.............................................................................................................................................................141 14.0 Input Capture with Dedicated Timers.......................................................................................................................................147 15.0 Output Compare with Dedicated Timers..................................................................................................................................151 16.0 Serial Peripheral Interface (SPI)...............................................................................................................................................161 17.0 Inter-Integrated Circuit (I2C).....................................................................................................................................................169 18.0 Universal Asynchronous Receiver Transmitter (UART)...........................................................................................................177 19.0 Real-Time Clock and Calendar (RTCC) ..................................................................................................................................185 20.0 32-Bit Programmable Cyclic Redundancy Check (CRC) Generator........................................................................................199 21.0 High/Low-Voltage Detect (HLVD).............................................................................................................................................205 22.0 12-Bit A/D Converter with Threshold Detect............................................................................................................................207 23.0 Comparator Module..................................................................................................................................................................225 24.0 Comparator Voltage Reference................................................................................................................................................229 25.0 Charge Time Measurement Unit (CTMU)................................................................................................................................231 26.0 Special Features......................................................................................................................................................................239 27.0 Development Support...............................................................................................................................................................251 28.0 Instruction Set Summary..........................................................................................................................................................255 29.0 Electrical Characteristics..........................................................................................................................................................263 30.0 DC and AC Characteristics Graphs and Tables.......................................................................................................................295 31.0 Packaging Information..............................................................................................................................................................325 Appendix A: Revision History.............................................................................................................................................................353 Index..................................................................................................................................................................................................355 The Microchip Web Site.....................................................................................................................................................................361 Customer Change Notification Service..............................................................................................................................................361 Customer Support..............................................................................................................................................................................361 Product Identification System.............................................................................................................................................................363 DS30009995E-page 8  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY TO OUR VALUED CUSTOMERS It is our intention to provide our valued customers with the best documentation possible to ensure successful use of your Microchip products. To this end, we will continue to improve our publications to better suit your needs. Our publications will be refined and enhanced as new volumes and updates are introduced. If you have any questions or comments regarding this publication, please contact the Marketing Communications Department via E-mail at docerrors@microchip.com. We welcome your feedback. Most Current Data Sheet To obtain the most up-to-date version of this data sheet, please register at our Worldwide Web site at: http://www.microchip.com You can determine the version of a data sheet by examining its literature number found on the bottom outside corner of any page. The last character of the literature number is the version number, (e.g., DS30000000A is version A of document DS30000000). Errata An errata sheet, describing minor operational differences from the data sheet and recommended work arounds, may exist for current devices. As device/documentation issues become known to us, we will publish an errata sheet. The errata will specify the revision of silicon and revision of document to which it applies. To determine if an errata sheet exists for a particular device, please check with one of the following: • Microchip’s Worldwide Web site; http://www.microchip.com • Your local Microchip sales office (see last page) When contacting a sales office, please specify which device, revision of silicon and data sheet (include literature number) you are using. Customer Notification System Register on our web site at www.microchip.com to receive the most current information on all of our products.  2011-2017 Microchip Technology Inc. DS30009995E-page 9

PIC24FV32KA304 FAMILY NOTES: DS30009995E-page 10  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 1.0 DEVICE OVERVIEW 1.1.2 POWER-SAVING TECHNOLOGY All of the devices in the PIC24FV32KA304 family This document contains device-specific information for incorporate a range of features that can significantly the following devices: reduce power consumption during operation. Key • PIC24FV16KA301, PIC24F16KA301 features include: • PIC24FV16KA302, PIC24F16KA302 • On-the-Fly Clock Switching: The device clock • PIC24FV16KA304, PIC24F16KA304 can be changed under software control to the • PIC24FV32KA301, PIC24F32KA301 Timer1 source or the internal, low-power RC • PIC24FV32KA302, PIC24F32KA302 oscillator during operation, allowing users to • PIC24FV32KA304, PIC24F32KA304 incorporate power-saving ideas into their software The PIC24FV32KA304 family introduces a new line of designs. extreme low-power Microchip devices. This is a 16-bit • Doze Mode Operation: When timing-sensitive microcontroller family with a broad peripheral feature applications, such as serial communications, set and enhanced computational performance. This require the uninterrupted operation of peripherals, family also offers a new migration option for those the CPU clock speed can be selectively reduced, high-performance applications which may be out- allowing incremental power savings without growing their 8-bit platforms, but do not require the missing a beat. numerical processing power of a Digital Signal • Instruction-Based Power-Saving Modes: There Processor (DSP). are three instruction-based power-saving modes: - Idle Mode: The core is shut down while 1.1 Core Features leaving the peripherals active. 1.1.1 16-BIT ARCHITECTURE - Sleep Mode: The core and peripherals that require the system clock are shut down, Central to all PIC24F devices is the 16-bit modified leaving the peripherals that use their own Harvard architecture, first introduced with Microchip’s clock, or the clock from other devices, active. dsPIC® digital signal controllers. The PIC24F CPU core - Deep Sleep Mode: The core, peripherals offers a wide range of enhancements, such as: (except RTCC and DSWDT), Flash and • 16-bit data and 24-bit address paths with the SRAM are shut down. ability to move information between data and memory spaces 1.1.3 OSCILLATOR OPTIONS AND • Linear addressing of up to 12Mbytes (program FEATURES space) and 64Kbytes (data) The PIC24FV32KA304 family offers five different • A 16-element Working register array with built-in oscillator options, allowing users a range of choices in software stack support developing application hardware. These include: • A 17 x 17 hardware multiplier with support for • Two Crystal modes using crystals or ceramic integer math resonators. • Hardware support for 32-bit by 16-bit division • Two External Clock modes offering the option of a • An instruction set that supports multiple divide-by-2 clock output. addressing modes and is optimized for high-level • Two Fast Internal oscillators (FRCs): One with a languages, such as C nominal 8 MHz output and the other with a • Operational performance up to 16 MIPS nominal 500 kHz output. These outputs can also be divided under software control to provide clock speed as low as 31 kHz or 2 kHz. • A Phase Locked Loop (PLL) frequency multiplier, available to the external Oscillator modes and the 8 MHz FRC oscillator, which allows clock speeds of up to 32 MHz. • A separate internal RC oscillator (LPRC) with a fixed 31 kHz output, which provides a low-power option for timing-insensitive applications.  2011-2017 Microchip Technology Inc. DS30009995E-page 11

PIC24FV32KA304 FAMILY The internal oscillator block also provides a stable 1.3 Details on Individual Family reference source for the Fail-Safe Clock Monitor Members (FSCM). This option constantly monitors the main clock source against a reference signal provided by the Devices in the PIC24FV32KA304 family are available internal oscillator and enables the controller to switch to in 20-pin, 28-pin, 44-pin and 48-pin packages. The the internal oscillator, allowing for continued low-speed general block diagram for all devices is shown in operation or a safe application shutdown. Figure1-1. The devices are different from each other in four ways: 1.1.4 EASY MIGRATION 1. Flash program memory (16 Kbytes for Regardless of the memory size, all the devices share PIC24FV16KA devices, 32 Kbytes for the same rich set of peripherals, allowing for a smooth PIC24FV32KA devices). migration path as applications grow and evolve. 2. Available I/O pins and ports (18 pins on two The consistent pinout scheme used throughout the ports for 20-pin devices, 22 pins on two ports for entire family also helps in migrating to the next larger 28-pin devices and 38 pins on three ports for device. This is true when moving between devices with 44/48-pin devices). the same pin count, or even jumping from 20-pin or 3. Alternate SCLx and SDAx pins are available 28-pin devices to 44-pin/48-pin devices. only in 28-pin, 44-pin and 48-pin devices and not The PIC24F family is pin compatible with devices in the in 20-pin devices. dsPIC33 family, and shares some compatibility with the 4. Members of the PIC24FV32KA301 family are pinout schema for PIC18 and dsPIC30. This extends available as both standard and high-voltage the ability of applications to grow from the relatively devices. High-voltage devices, designated with simple, to the powerful and complex. an “FV” in the part number (such as PIC24FV32KA304), accommodate an operating 1.2 Other Special Features VDD range of 2.0V to 5.5V, and have an on-board Voltage Regulator that powers the core. Peripher- • Communications: The PIC24FV32KA304 family als operate at VDD. Standard devices, designated incorporates a range of serial communication by “F” (such as PIC24F32KA304), function over peripherals to handle a range of application a lower VDD range of 1.8V to 3.6V. These parts requirements. There is an I2C module that do not have an internal regulator, and both the supports both the Master and Slave modes of core and peripherals operate directly from VDD. operation. It also comprises UARTs with built-in IrDA® encoders/decoders and an SPI module. All other features for devices in this family are identical; these are summarized in Table1-1. • Real-Time Clock/Calendar: This module implements a full-featured clock and calendar with A list of the pin features available on the alarm functions in hardware, freeing up timer PIC24FV32KA304 family devices, sorted by function, resources and program memory space for use of is provided in Table1-3. the core application. Note: Table1-1 provides the pin location of • 12-Bit A/D Converter: This module incorporates individual peripheral features and not how programmable acquisition time, allowing for a they are multiplexed on the same pin. This channel to be selected and a conversion to be information is provided in the pinout initiated without waiting for a sampling period, and diagrams on pages 3, 4, 5, 6 and 7 of the faster sampling speed. The 16-deep result buffer data sheet. Multiplexed features are can be used either in Sleep to reduce power, or in sorted by the priority given to a feature, Active mode to improve throughput. with the highest priority peripheral being • Charge Time Measurement Unit (CTMU) listed first. Interface: The PIC24FV32KA304 family includes the new CTMU interface module, which can be used for capacitive touch sensing, proximity sensing, and also for precision time measurement and pulse generation. DS30009995E-page 12  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY TABLE 1-1: DEVICE FEATURES FOR THE PIC24FV32KA304 FAMILY 1 1 2 2 4 4 0 0 0 0 0 0 3 3 3 3 3 3 A A A A A A K K K K K K 6 2 6 2 6 2 Features 1 3 1 3 1 3 V V V V V V F F F F F F 4 4 4 4 4 4 2 2 2 2 2 2 C C C C C C PI PI PI PI PI PI Operating Frequency DC – 32 MHz Program Memory (bytes) 16K 32K 16K 32K 16K 32K Program Memory (instructions) 5632 11264 5632 11264 5632 11264 Data Memory (bytes) 2048 Data EEPROM Memory (bytes) 512 Interrupt Sources (soft vectors/ 30 (26/4) NMI traps) I/O Ports PORTA<5:0> PORTA<7,5:0> PORTA<11:7,5:0> PORTB<15:12,9:7,4,2:0> PORTB<15:0> PORTB<15:0> PORTC<9:0> Total I/O Pins 17 23 38 Timers: Total Number (16-bit) 5 32-Bit (from paired 16-bit timers) 2 Input Capture Channels 3 Output Compare/PWM Channels 3 Input Change Notification Interrupt 16 22 37 Serial Communications: UART 2 SPI (3-wire/4-wire) I2C 2 12-Bit Analog-to-Digital Module 12 13 16 (input channels) Analog Comparators 3 Resets (and delays) POR, BOR, RESET Instruction, MCLR, WDT, Illegal Opcode, REPEAT Instruction, Hardware Traps, Configuration Word Mismatch (PWRT, OST, PLL Lock) Instruction Set 76 Base Instructions, Multiple Addressing Mode Variations Packages 20-Pin 28-Pin 44-Pin QFN/TQFP PDIP/SSOP/SOIC SPDIP/SSOP/SOIC/QFN 48-Pin UQFN  2011-2017 Microchip Technology Inc. DS30009995E-page 13

PIC24FV32KA304 FAMILY TABLE 1-2: DEVICE FEATURES FOR THE PIC24F32KA304 FAMILY 1 1 2 2 4 4 0 0 0 0 0 0 3 3 3 3 3 3 A A A A A A K K K K K K Features 16 32 16 32 16 32 F F F F F F 4 4 4 4 6 4 2 2 2 2 1 2 C C C C C C PI PI PI PI PI PI Operating Frequency DC – 32 MHz Program Memory (bytes) 16K 32K 16K 32K 16K 32K Program Memory (instructions) 5632 11264 5632 11264 5632 11264 Data Memory (bytes) 2048 Data EEPROM Memory (bytes) 512 Interrupt Sources (soft vectors/ 30 (26/4) NMI traps) I/O Ports PORTA<6:0>, PORTA<7:0>, PORTA<11:0>, PORTB<15:12, 9:7, 4, 2:0> PORTB<15:0> PORTB<15:0>, PORTC<9:0> Total I/O Pins 18 24 39 Timers: Total Number (16-bit) 5 32-Bit (from paired 16-bit timers) 2 Input Capture Channels 3 Output Compare/PWM Channels 3 Input Change Notification Interrupt 17 23 38 Serial Communications: UART 2 SPI (3-wire/4-wire) I2C 2 12-Bit Analog-to-Digital Module 12 13 16 (input channels) Analog Comparators 3 Resets (and delays) POR, BOR, RESET Instruction, MCLR, WDT, Illegal Opcode, REPEAT Instruction, Hardware Traps, Configuration Word Mismatch (PWRT, OST, PLL Lock) Instruction Set 76 Base Instructions, Multiple Addressing Mode Variations Packages 20-Pin 28-Pin 44-Pin QFN/TQFP PDIP/SSOP/SOIC SPDIP/SSOP/SOIC/QFN 48-Pin UQFN DS30009995E-page 14  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY FIGURE 1-1: PIC24FV32KA304 FAMILY GENERAL BLOCK DIAGRAM Interrupt Data Bus Controller 16 8 16 16 PSV and Table Data Latch Data Access Control Block PCH PCL DataRAM 23 Program Counter Address Stack Repeat Latch PORTA(1) Control Control Logic Logic RA<0:7> 16 23 16 Address Latch Read AGU Write AGU Program Memory PORTB(1) Data EEPROM RB<0:15> Data Latch EA MUX 16 Address Bus a 24 al Dat 16 16 PORTC(1) Inst Latch Liter RC<9:0> Inst Register Instruction Decode and Control Divide Control Signals Support 16 x 16 17x17 W Reg Array OSCO/CLKO Timing Power-up Multiplier OSCI/CLKI Generation Timer Oscillator FRC/LPRC Start-up Timer Oscillators Power-on 16-Bit ALU Reset Precision Watchdog 16 Band Gap Timer Reference DSWDT Voltage BOR Regulator VCAP VDD, VSS MCLR 12-Bit HLVD RTCC Timer1 Timer2/3 Timer4/5 CTMU Comparators A/D REFO IC1-3 PWM/ CN1-22(1) SPI1 I2C1 UART1/2 OC1-3 Note 1: All pins or features are not implemented on all device pinout configurations. See Table1-3 for I/O port pin descriptions.  2011-2017 Microchip Technology Inc. DS30009995E-page 15

D TABLE 1-3: PIC24FV32KA304 FAMILY PINOUT DESCRIPTIONS P S 30 I 0 F FV C 0 9 99 Pin Number Pin Number 2 5E Function I/O Buffer Description 4 -p 20-Pin 28-Pin 44-Pin 20-Pin 28-Pin 44-Pin F a PDIP/ SPDIP/ 28-Pin 48-Pin PDIP/ SPDIP/ 28-Pin 48-Pin g QFN/ QFN/ e SSOP/ SSOP/ QFN UQFN SSOP/ SSOP/ QFN UQFN V 1 SOIC SOIC TQFP SOIC SOIC TQFP 6 3 AN0 2 2 27 19 21 2 2 27 19 21 I ANA A/D Analog Inputs 2 AN1 3 3 28 20 22 3 3 28 20 22 I ANA K AN2 4 4 1 21 23 4 4 1 21 23 I ANA A AN3 5 5 2 22 24 5 5 2 22 24 I ANA 3 AN4 6 6 3 23 25 6 6 3 23 25 I ANA 0 AN5 — 7 4 24 26 — 7 4 24 26 I ANA 4 AN6 — — — 25 27 — — — 25 27 I ANA AN7 — — — 26 28 — — — 26 28 I ANA F AN8 — — — 27 29 — — — 27 29 I ANA A AN9 18 26 23 15 16 18 26 23 15 16 I ANA M AN10 17 25 22 14 15 17 25 22 14 15 I ANA I AN11 16 24 21 11 12 16 24 21 11 12 I ANA L AN12 15 23 20 10 11 15 23 20 10 11 I ANA Y AN13 7 9 6 30 33 7 9 6 30 33 I ANA AN14 8 10 7 31 34 8 10 7 31 34 I ANA AN15 9 11 8 33 36 9 11 8 33 36 I ANA ASCL1 — 15 12 42 46 — 15 12 42 46 I/O I2C Alternate I2C1 Clock Input/Output ASDA1 — 14 11 41 45 — 14 11 41 45 I/O I2C Alternate I2C1 Data Input/Output AVDD 20 28 25 17 18 20 28 25 17 18 I ANA A/D Supply Pins AVSS 19 27 24 16 17 19 27 24 16 17 I ANA  2 C1INA 8 7 4 24 26 8 7 4 24 26 I ANA Comparator 1 Input A (+) 0 1 C1INB 7 6 3 23 25 7 6 3 23 25 I ANA Comparator 1 Input B (-) 1 -2 C1INC 5 5 2 22 24 5 5 2 22 24 I ANA Comparator 1 Input C (+) 0 17 C1IND 4 4 1 21 23 4 4 1 21 23 I ANA Comparator 1 Input D (-) M C1OUT 17 25 22 14 15 17 25 22 14 15 O — Comparator 1 Output ic ro C2INA 5 5 2 22 24 5 5 2 22 24 I ANA Comparator 2 Input A (+) c h ip C2INB 4 4 1 21 23 4 4 1 21 23 I ANA Comparator 2 Input B (-) Te C2INC 8 7 4 24 26 8 7 4 24 26 I ANA Comparator 2 Input C (+) c h C2IND 7 6 3 23 25 7 6 3 23 25 I ANA Comparator 2 Input D (-) n o lo C2OUT 14 20 17 7 7 11 16 13 43 47 O — Comparator 2 Output g y In c .

 TABLE 1-3: PIC24FV32KA304 FAMILY PINOUT DESCRIPTIONS (CONTINUED) 2 0 1 F FV 1 -2 0 Pin Number Pin Number 1 7 M Function 20-Pin 28-Pin 20-Pin 28-Pin I/O Buffer Description 44-Pin 44-Pin icro SPSDOIPP// SSPSDOIPP// 2Q8-FPNin QFN/ 4U8Q-PFiNn SPSDOIPP// SSPSDOIPP// 2 8Q-FPNin QFN/ 4U8Q-PFiNn c TQFP TQFP h SOIC SOIC SOIC SOIC ip T C3INA 18 26 23 15 16 18 26 23 15 16 I ANA Comparator 3 Input A (+) e c h C3INB 17 25 22 14 15 17 25 22 14 15 I ANA Comparator 3 Input B (-) n o lo C3INC 2 2 27 19 21 2 2 27 19 21 I ANA Comparator 3 Input C (+) g y C3IND 4 4 1 21 23 4 4 1 21 23 I ANA Comparator 3 Input D (-) In c C3OUT 12 17 14 44 48 12 17 14 44 48 O — Comparator 3 Output . CLK I 7 9 6 30 33 7 9 6 30 33 I ANA Main Clock Input CLKO 8 10 7 31 34 8 10 7 31 34 O — System Clock Output CN0 10 12 9 34 37 10 12 9 34 37 I ST Interrupt-on-Change Inputs CN1 9 11 8 33 36 9 11 8 33 36 I ST CN2 2 2 27 19 21 2 2 27 19 21 I ST CN3 3 3 28 20 22 3 3 28 20 22 I ST CN4 4 4 1 21 23 4 4 1 21 23 I ST P CN5 5 5 2 22 24 5 5 2 22 24 I ST I CN6 6 6 3 23 25 6 6 3 23 25 I ST C CN7 — 7 4 24 26 –- 7 4 24 26 I ST 2 CN8 14 20 17 7 7 –- –- –- — –- I ST 4 CN9 –- 19 16 6 6 –- 19 16 6 6 I ST F CN10 –- — — 27 29 –- –- –- 27 29 I ST V CN11 18 26 23 15 16 18 26 23 15 16 I ST 3 CN12 17 25 22 14 15 17 25 22 14 15 I ST 2 CN13 16 24 21 11 12 16 24 21 11 12 I ST K CN14 15 23 20 10 11 15 23 20 10 11 I ST A CN15 –- 22 19 9 10 –- 22 19 9 10 I ST 3 CN16 –- 21 18 8 9 –- 21 18 8 9 I ST 0 CN17 –- — — 3 3 –- — — 3 3 I ST 4 D S CN18 — — — 2 2 — — — 2 2 I ST 3 F 0 CN19 –- — — 5 5 — — –- 5 5 I ST 009 CN20 –- — — 4 4 — –- –- 4 4 I ST A 9 95 CN21 13 18 15 1 1 13 18 15 1 1 I ST M E -p CN22 12 17 14 44 48 12 17 14 44 48 I ST I a L g e 1 Y 7

D TABLE 1-3: PIC24FV32KA304 FAMILY PINOUT DESCRIPTIONS (CONTINUED) P S 300 F FV IC 0 9 9 Pin Number Pin Number 2 9 5E Function 20-Pin 28-Pin 20-Pin 28-Pin I/O Buffer Description 4 -pa PDIP/ SPDIP/ 28-Pin 4Q4F-PNin/ 48-Pin PDIP/ SPDIP/ 28-Pin 4Q4F-PNin/ 48-Pin F g SSOP/ SSOP/ QFN UQFN SSOP/ SSOP/ QFN UQFN e TQFP TQFP V 1 SOIC SOIC SOIC SOIC 8 3 CN23 11 16 13 43 47 11 16 13 43 47 I ST Interrupt-on-Change Inputs 2 CN24 –- 15 12 42 46 –- 15 12 42 46 I ST K CN25 –- — — 37 40 –- –- –- 37 40 I ST A CN26 –- — — 38 41 –- –- –- 38 41 I ST CN27 –- 14 11 41 45 –- 14 11 41 45 I ST 3 0 CN28 –- — — 36 39 –- –- –- 36 39 I ST 4 CN29 8 10 7 31 34 8 10 7 31 34 I ST CN30 7 9 6 30 33 7 9 6 30 33 I ST F CN31 –- — — 26 28 — — — 26 28 I ST A CN32 –- — — 25 27 — — — 25 27 I ST M CN33 –- — — 32 35 — — — 32 35 I ST I CN34 –- — — 35 38 — — — 35 38 I ST L CN35 –- — — 12 13 — — — 12 13 I ST Y CN36 –- — — 13 14 — — — 13 14 I ST CVREF 17 25 22 14 15 17 25 22 14 15 I ANA Comparator Voltage Reference Output CVREF+ 2 2 27 19 21 2 2 27 19 21 I ANA Comparator Reference Positive Input Voltage CVREF- 3 3 28 20 22 3 3 28 20 22 I ANA Comparator Reference Negative Input Voltage CTCMP 4 4 1 21 23 4 4 1 21 23 I ANA CTMU Comparator Input CTED1 14 20 17 7 7 11 2 27 19 21 I ST CTMU Trigger Edge Inputs CTED2 15 23 20 10 11 15 23 20 10 11 I ST  CTED3 — 19 16 6 6 — 19 16 6 6 I ST 2 0 CTED4 13 18 15 1 1 13 18 15 1 1 I ST 1 1 -2 CTED5 17 25 22 14 15 17 25 22 14 15 I ST 0 1 CTED6 18 26 23 15 16 18 26 23 15 16 I ST 7 M CTED7 — — — 5 5 — — — 5 5 I ST ic ro CTED8 — — — 13 14 — — — 13 14 I ST c h CTED9 — 22 19 9 10 — 22 19 9 10 I ST ip T CTED10 12 17 14 44 48 12 17 14 44 48 I ST e ch CTED11 — 21 18 8 9 — 21 18 8 9 I ST n o CTED12 5 5 2 22 24 5 5 2 22 24 I ST lo gy CTED13 6 6 3 23 25 6 6 3 23 25 I ST In c .

 TABLE 1-3: PIC24FV32KA304 FAMILY PINOUT DESCRIPTIONS (CONTINUED) 2 0 1 F FV 1 -2 0 Pin Number Pin Number 1 7 M Function 20-Pin 28-Pin 20-Pin 28-Pin I/O Buffer Description 44-Pin 44-Pin icro SPSDOIPP// SSPSDOIPP// 2Q8-FPNin QFN/ 4U8Q-PFiNn SPSDOIPP// SSPSDOIPP// 2 8Q-FPNin QFN/ 4U8Q-PFiNn c TQFP TQFP h SOIC SOIC SOIC SOIC ip T CTPLS 16 24 21 11 12 16 24 21 11 12 O — CTMU Pulse Output e c h HLVDIN 15 23 20 10 11 15 23 20 10 11 I ST High/Low-Voltage Detect Input n o lo IC1 14 19 16 6 6 11 19 16 6 6 I ST Input Capture 1 Input g y IC2 13 18 15 5 5 13 18 15 5 5 I ST Input Capture 2 Input In c IC3 15 23 20 13 14 15 23 20 13 14 I ST Input Capture 3 Input . INT0 11 16 13 43 47 11 16 13 43 47 I ST Interrupt 0 Input INT1 17 25 22 14 15 17 25 22 14 15 I ST Interrupt 1 Input INT2 14 20 17 7 7 15 23 20 10 11 I ST Interrupt 2 Input MCLR 1 1 26 18 19 1 1 26 18 19 I ST Master Clear (Device Reset) Input (active-low) OC1 14 20 17 7 7 11 16 13 43 47 O — Output Compare/PWM1 Output OC2 4 22 19 4 4 4 22 19 4 4 O — Output Compare/PWM2 Output OC3 5 21 18 12 13 5 21 18 12 13 O — Output Compare/PWM3 Output P OCFA 17 25 22 14 15 17 25 22 14 15 O — Output Compare Fault A I OFCB 16 24 21 32 35 16 24 21 32 35 O — Output Compare Fault B C OSCI 7 9 6 30 33 7 9 6 30 33 I ANA Main Oscillator Input 2 OSCO 8 10 7 31 34 8 10 7 31 34 O ANA Main Oscillator Output 4 PGEC1 5 5 2 22 24 5 5 2 22 24 I/O ST ICSP™ Clock 1 F PCED1 4 4 1 21 23 4 4 1 21 23 I/O ST ICSP Data 1 V PGEC2 2 22 19 9 10 2 22 19 9 10 I/O ST ICSP Clock 2 3 PGED2 3 21 18 8 9 3 21 18 8 9 I/O ST ICSP Data 2 2 PGEC3 10 15 12 42 46 10 15 12 42 46 I/O ST ICSP Clock 3 K PGED3 9 14 11 41 45 9 14 11 41 45 I/O ST ICSP Data 3 A 3 0 4 D S 3 F 0 00 A 9 9 9 M 5 E -p I a L g e 1 Y 9

D TABLE 1-3: PIC24FV32KA304 FAMILY PINOUT DESCRIPTIONS (CONTINUED) P S 300 F FV IC 0 9 9 Pin Number Pin Number 2 9 5E Function 20-Pin 28-Pin 20-Pin 28-Pin I/O Buffer Description 4 -pa PDIP/ SPDIP/ 28-Pin 4Q4F-PNin/ 48-Pin PDIP/ SPDIP/ 28-Pin 4Q4F-PNin/ 48-Pin F g SSOP/ SSOP/ QFN UQFN SSOP/ SSOP/ QFN UQFN e TQFP TQFP V 2 SOIC SOIC SOIC SOIC 0 3 RA0 2 2 27 19 21 2 2 27 19 21 I/O ST PORTA Pins 2 RA1 3 3 28 20 22 3 3 28 20 22 I/O ST K RA2 7 9 6 30 33 7 9 6 30 33 I/O ST A RA3 8 10 7 31 34 8 10 7 31 34 I/O ST RA4 10 12 9 34 37 10 12 9 34 37 I/O ST 3 0 RA5 1 1 26 18 19 1 1 26 18 19 I/O ST 4 RA6 14 20 17 7 7 — — — — — I/O ST RA7 — 19 16 6 6 — 19 16 6 6 I/O ST F RA8 — — — 32 35 — — — 32 35 I/O ST A RA9 — — — 35 38 — — — 35 38 I/O ST M RA10 — — — 12 13 — — — 12 13 I/O ST I RA11 — — — 13 14 — — — 13 14 I/O ST L RB0 4 4 1 21 23 4 4 1 21 23 I/O ST PORTB Pins Y RB1 5 5 2 22 24 5 5 2 22 24 I/O ST RB2 6 6 3 23 25 6 6 3 23 25 I/O ST RB3 — 7 4 24 26 — 7 4 24 26 I/O ST RB4 9 11 8 33 36 9 11 8 33 36 I/O ST RB5 — 14 11 41 45 — 14 11 41 45 I/O ST RB6 — 15 12 42 46 — 15 12 42 46 I/O ST RB7 11 16 13 43 47 11 16 13 43 47 I/O ST  RB8 12 17 14 44 48 12 17 14 44 48 I/O ST 2 0 RB9 13 18 15 1 1 13 18 15 1 1 I/O ST 1 1 -2 RB10 — 21 18 8 9 — 21 18 8 9 I/O ST 0 1 RB11 — 22 19 9 10 — 22 19 9 10 I/O ST 7 M RB12 15 23 20 10 11 15 23 20 10 11 I/O ST ic ro RB13 16 24 21 11 12 16 24 21 11 12 I/O ST c h RB14 17 25 22 14 15 17 25 22 14 15 I/O ST ip T RB15 18 26 23 15 16 18 26 23 15 16 I/O ST e c h n o lo g y In c .

 TABLE 1-3: PIC24FV32KA304 FAMILY PINOUT DESCRIPTIONS (CONTINUED) 2 0 1 F FV 1 -2 0 Pin Number Pin Number 1 7 M Function 20-Pin 28-Pin 20-Pin 28-Pin I/O Buffer Description 44-Pin 44-Pin icro SPSDOIPP// SSPSDOIPP// 2Q8-FPNin QFN/ 4U8Q-PFiNn SPSDOIPP// SSPSDOIPP// 2 8Q-FPNin QFN/ 4U8Q-PFiNn c TQFP TQFP h SOIC SOIC SOIC SOIC ip T RC0 — — — 25 27 — — — 25 27 I/O ST PORTC Pins e c h RC1 — — — 26 28 — — — 26 28 I/O ST n o lo RC2 — — — 27 29 — — — 27 29 I/O ST g y RC3 — — — 36 39 — — — 36 39 I/O ST In c RC4 — — — 37 40 — — — 37 40 I/O ST . RC5 — — — 38 41 — — — 38 41 I/O ST RC6 — — — 2 2 — — — 2 2 I/O ST RC7 — — — 3 3 — — — 3 3 I/O ST RC8 — — — 4 4 — — — 4 4 I/O ST RC9 — — — 5 5 — — — 5 5 I/O ST REFO 18 26 23 15 16 18 26 23 15 16 O — Reference Clock Output RTCC 17 25 22 14 15 17 25 22 14 15 O — Real-Time Clock/Calendar Output P SCK1 15 22 19 9 10 15 22 19 9 10 I/O ST SPI1 Serial Input/Output Clock I SCK2 2 14 11 38 41 2 14 11 38 41 I/O ST SPI2 Serial Input/Output Clock C SCL1 12 17 14 44 48 12 17 14 44 48 I/O I2C I2C1 Clock Input/Output 2 SCL2 18 7 4 24 26 18 7 4 24 26 I/O I2C I2C2 Clock Input/Output 4 SCLKI 10 12 9 34 37 10 12 9 34 37 I ST Digital Secondary Clock Input F SDA1 13 18 15 1 1 13 18 15 1 1 I/O I2C I2C1 Data Input/Output V SDA2 6 6 3 23 25 6 6 3 23 25 I/O I2C I2C2 Data Input/Output 3 SDI1 17 21 18 8 9 17 21 18 8 9 I ST SPI1 Serial Data Input 2 SDI2 4 19 16 36 39 4 19 16 36 39 I ST SPI2 Serial Data Input K SDO1 16 24 21 11 12 16 24 21 11 12 O — SPI1 Serial Data Output A SDO2 3 15 12 37 40 3 15 12 37 40 O — SPI2 Serial Data Output 3 SOSCI 9 11 8 33 36 9 11 8 33 36 I ANA Secondary Oscillator Input 0 SOSCO 10 12 9 34 37 10 12 9 34 37 O ANA Secondary Oscillator Output 4 D S SS1 18 26 23 15 16 18 26 23 15 16 O — SPI1 Slave Select 3 F 000 SS2 15 23 20 35 38 15 23 20 35 38 O — SPI2 Slave Select A 9 9 9 M 5 E -p I a L g e 2 Y 1

D TABLE 1-3: PIC24FV32KA304 FAMILY PINOUT DESCRIPTIONS (CONTINUED) P S 300 F FV IC 0 9 9 Pin Number Pin Number 2 9 5E Function 20-Pin 28-Pin 20-Pin 28-Pin I/O Buffer Description 4 -pa PDIP/ SPDIP/ 28-Pin 4Q4F-PNin/ 48-Pin PDIP/ SPDIP/ 28-Pin 4Q4F-PNin/ 48-Pin F g SSOP/ SSOP/ QFN UQFN SSOP/ SSOP/ QFN UQFN e TQFP TQFP V 2 SOIC SOIC SOIC SOIC 2 3 T1CK 13 18 15 1 1 13 18 15 1 1 I ST Timer1 Clock 2 T2CK 18 26 23 15 16 18 26 23 15 16 I ST Timer2 Clock K T3CK 18 26 23 15 16 18 26 23 15 16 I ST Timer3 Clock A T4CK 6 6 3 23 25 6 6 3 23 25 I ST Timer4 Clock T5CK 6 6 3 23 25 6 6 3 23 25 I ST Timer5 Clock 3 0 U1CTS 12 17 14 44 48 12 17 14 44 48 I ST UART1 Clear-to-Send Input 4 U1RTS 13 18 15 1 1 13 18 15 1 1 O — UART1 Request-to-Send Output U1RX 6 6 3 2 2 6 6 3 2 2 I ST UART1 Receive F U1TX 11 16 13 3 3 11 16 13 3 3 O — UART1 Transmit A U2CTS 10 12 9 34 37 10 12 9 34 37 I ST UART2 Clear-to-Send Input M U2RTS 9 11 8 33 36 9 11 8 33 36 O — UART2 Request-to-Send Output I L U2RX 5 5 2 22 24 5 5 2 22 24 I ST UART2 Receive U2TX 4 4 1 21 23 4 4 1 21 23 O — UART2 Transmit Y ULPWU 4 4 1 21 23 4 4 1 21 23 I ANA Ultra Low-Power Wake-up Input VCAP — — — — — 14 20 17 7 7 P — Core Power VDD 20 28,13 25,10 17,28,40 18,30,43 20 28,13 25,10 17,28,40 18,30,43 P — Device Digital Supply Voltage VREF+ 2 2 27 19 21 2 2 27 19 21 I ANA A/D Reference Voltage Input (+) VREF- 3 3 28 20 22 3 3 28 20 22 I ANA A/D Reference Voltage Input (-) VSS 19 27,8 24,5 16,29,39 17,31,42 19 27,8 24,5 16,29,39 17,31,42 P — Device Digital Ground Return  2 0 1 1 -2 0 1 7 M ic ro c h ip T e c h n o lo g y In c .

PIC24FV32KA304 FAMILY 2.0 GUIDELINES FOR GETTING FIGURE 2-1: RECOMMENDED STARTED WITH 16-BIT MINIMUM CONNECTIONS MICROCONTROLLERS C2(2) 2.1 Basic Connection Requirements VDD Getting started with the PIC24FV32KA304 family of D S R1 D S 16-bit microcontrollers requires attention to a minimal V V R2 set of device pin connections before proceeding with MCLR development. VCAP (1) C1 The following pins must always be connected: PIC24FXXKXX(3) C7 • All VDD and VSS pins (see Section2.2 “Power Supply Pins”) VSS VDD • All AVDD and AVSS pins, regardless of whether or C6(2) C3(2) not the analog device features are used VDD D S VSS D S D S (see Section2.2 “Power Supply Pins”) V V D S A A V V • MCLR pin (see Section2.3 “Master Clear (MCLR) Pin”) C5(2) C4(2) • VCAP pins (see Section2.4 “Voltage Regulator Pin (VCAP)”) These pins must also be connected if they are being Key (all values are recommendations): used in the end application: C1 through C6: 0.1 F, 20V ceramic • PGECx/PGEDx pins used for In-Circuit Serial C7: 10 F, 16V tantalum or ceramic Programming™ (ICSP™) and debugging purposes R1: 10 kΩ (see Section2.5 “ICSP Pins”) R2: 100Ω to 470Ω • OSCI and OSCO pins when an external oscillator Note 1: See Section2.4 “Voltage Regulator Pin source is used (VCAP)” for explanation of VCAP pin (see Section2.6 “External Oscillator Pins”) connections. Additionally, the following pins may be required: 2: The example shown is for a PIC24F device with five VDD/VSS and AVDD/AVSS pairs. • VREF+/VREF- pins are used when external voltage Other devices may have more or less pairs; reference for analog modules is implemented adjust the number of decoupling capacitors Note: The AVDD and AVSS pins must always be appropriately. connected, regardless of whether any of 3: Some PIC24F K parts do not have a the analog modules are being used. regulator. The minimum mandatory connections are shown in Figure2-1.  2011-2017 Microchip Technology Inc. DS30009995E-page 23

PIC24FV32KA304 FAMILY 2.2 Power Supply Pins 2.3 Master Clear (MCLR) Pin 2.2.1 DECOUPLING CAPACITORS The MCLR pin provides two specific device functions: Device Reset, and Device Programming and Debug- The use of decoupling capacitors on every pair of ging. If programming and debugging are not required power supply pins, such as VDD, VSS, AVDD and in the end application, a direct connection to VDD may AVSS, is required. be all that is required. The addition of other compo- Consider the following criteria when using decoupling nents, to help increase the application’s resistance to capacitors: spurious Resets from voltage sags, may be beneficial. A typical configuration is shown in Figure2-1. Other • Value and type of capacitor: A 0.1 F (100 nF), circuit designs may be implemented, depending on the 10-20V capacitor is recommended. The capacitor application’s requirements. should be a low-ESR device, with a resonance frequency in the range of 200MHz and higher. During programming and debugging, the resistance Ceramic capacitors are recommended. and capacitance that can be added to the pin must • Placement on the printed circuit board: The be considered. Device programmers and debuggers decoupling capacitors should be placed as close drive the MCLR pin. Consequently, specific voltage to the pins as possible. It is recommended to levels (VIH and VIL) and fast signal transitions must not be adversely affected. Therefore, specific values place the capacitors on the same side of the board as the device. If space is constricted, the of R1 and C1 will need to be adjusted based on the application and PCB requirements. For example, it is capacitor can be placed on another layer on the recommended that the capacitor, C1, be isolated PCB using a via; however, ensure that the trace from the MCLR pin during programming and debug- length from the pin to the capacitor is no greater ging operations by using a jumper (Figure2-2). The than 0.25inch (6mm). jumper is replaced for normal run-time operations. • Handling high-frequency noise: If the board is experiencing high-frequency noise (upward of Any components associated with the MCLR pin tens of MHz), add a second ceramic type capaci- should be placed within 0.25 inch (6mm) of the pin. tor in parallel to the above described decoupling capacitor. The value of the second capacitor can FIGURE 2-2: EXAMPLE OF MCLR PIN be in the range of 0.01F to 0.001F. Place this CONNECTIONS second capacitor next to each primary decoupling capacitor. In high-speed circuit designs, consider VDD implementing a decade pair of capacitances as close to the power and ground pins as possible R1 (e.g., 0.1F in parallel with 0.001F). R2 • Maximizing performance: On the board layout MCLR from the power supply circuit, run the power and JP PIC24FXXKXXX return traces to the decoupling capacitors first, and then to the device pins. This ensures that the C1 decoupling capacitors are first in the power chain. Equally important is to keep the trace length between the capacitor and the power pins to a minimum, thereby reducing PCB trace Note 1: R110k is recommended. A suggested inductance. starting value is 10k. Ensure that the MCLR pin VIH and VIL specifications are 2.2.2 TANK CAPACITORS met. 2: R2470 will limit any current flowing On boards with power traces running longer than into MCLR from the external capacitor, C, sixinches in length, it is suggested to use a tank capac- in the event of MCLR pin breakdown due to itor for integrated circuits, including microcontrollers, to Electrostatic Discharge (ESD) or Electrical supply a local power source. The value of the tank Overstress (EOS). Ensure that the MCLR capacitor should be determined based on the trace pin VIH and VIL specifications are met. resistance that connects the power supply source to the device, and the maximum current drawn by the device in the application. In other words, select the tank capacitor so that it meets the acceptable voltage sag at the device. Typical values range from 4.7F to 47F. DS30009995E-page 24  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 2.4 Voltage Regulator Pin (VCAP) Refer to Section29.0 “Electrical Characteristics” for information on VDD and VDDCORE. Note: This section applies only to PIC24F K devices with an On-Chip Voltage Regulator. FIGURE 2-3: FREQUENCY vs. ESR PERFORMANCE FOR Some of the PIC24F K devices have an internal Voltage Regulator. These devices have the Voltage Regulator SUGGESTED VCAP output brought out on the VCAP pin. On the PIC24F K 10 devices with regulators, a low-ESR (< 5Ω) capacitor is required on the VCAP pin to stabilize the Voltage Regula- 1 tor output. The VCAP pin must not be connected to VDD and must use a capacitor of 10 µF connected to ground. ) The type can be ceramic or tantalum. Suitable examples R ( 0.1 of capacitors are shown in Table2-1. Capacitors with S E equivalent specifications can be used. 0.01 Designers may use Figure2-3 to evaluate ESR equivalence of candidate devices. 0.001 The placement of this capacitor should be close to VCAP. 0.01 0.1 1 10 100 1000 10,000 It is recommended that the trace length not exceed Frequency (MHz) 0.25inch (6 mm). Refer to Section29.0 “Electrical Note: Typical data measurement at 25°C, 0V DC bias. Characteristics” for additional information. TABLE 2-1: SUITABLE CAPACITOR EQUIVALENTS Nominal Make Part # Base Tolerance Rated Voltage Temp. Range Capacitance TDK C3216X7R1C106K 10 µF ±10% 16V -55 to 125ºC TDK C3216X5R1C106K 10 µF ±10% 16V -55 to 85ºC Panasonic ECJ-3YX1C106K 10 µF ±10% 16V -55 to 125ºC Panasonic ECJ-4YB1C106K 10 µF ±10% 16V -55 to 85ºC Murata GRM32DR71C106KA01L 10 µF ±10% 16V -55 to 125ºC Murata GRM31CR61C106KC31L 10 µF ±10% 16V -55 to 85ºC  2011-2017 Microchip Technology Inc. DS30009995E-page 25

PIC24FV32KA304 FAMILY 2.4.1 CONSIDERATIONS FOR CERAMIC FIGURE 2-4: DC BIAS VOLTAGE vs. CAPACITORS CAPACITANCE CHARACTERISTICS In recent years, large value, low-voltage, surface-mount ceramic capacitors have become very cost effective in sizes up to a few tens of microfarad. The low-ESR, small physical size and other properties make ceramic %) 10 e ( 0 capacitors very attractive in many types of applications. ng-10 16V Capacitor ha-20 Ceramic capacitors are suitable for use with the inter- C-30 nal Voltage Regulator of this microcontroller. However, ance --5400 10V Capacitor some care is needed in selecting the capacitor to cit-60 ensure that it maintains sufficient capacitance over the Capa--8700 6.3V Capacitor intended operating range of the application. 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 DC Bias Voltage (VDC) Typical low-cost, 10 F ceramic capacitors are available in X5R, X7R and Y5V dielectric ratings (other types are also available, but are less common). The initial toler- When selecting a ceramic capacitor to be used with the ance specifications for these types of capacitors are internal Voltage Regulator, it is suggested to select a often specified as ±10% to ±20% (X5R and X7R), or high-voltage rating, so that the operating voltage is a -20%/+80% (Y5V). However, the effective capacitance small percentage of the maximum rated capacitor volt- that these capacitors provide in an application circuit will age. For example, choose a ceramic capacitor rated at also vary based on additional factors, such as the 16V for the 3.3V or 2.5V core voltage. Suggested applied DC bias voltage and the temperature. The total capacitors are shown in Table2-1. in-circuit tolerance is, therefore, much wider than the initial tolerance specification. 2.5 ICSP Pins The X5R and X7R capacitors typically exhibit satisfac- The PGC and PGD pins are used for In-Circuit Serial tory temperature stability (ex: ±15% over a wide Programming™ (ICSP™) and debugging purposes. It temperature range, but consult the manufacturer’s data is recommended to keep the trace length between the sheets for exact specifications). However, Y5V capaci- ICSP connector and the ICSP pins on the device as tors typically have extreme temperature tolerance short as possible. If the ICSP connector is expected to specifications of +22%/-82%. Due to the extreme experience an ESD event, a series resistor is recom- temperature tolerance, a 10 F nominal rated Y5V type mended, with the value in the range of a few tens of capacitor may not deliver enough total capacitance to ohms, not to exceed 100Ω. meet minimum internal Voltage Regulator stability and Pull-up resistors, series diodes and capacitors on the transient response requirements. Therefore, Y5V PGC and PGD pins are not recommended as they will capacitors are not recommended for use with the interfere with the programmer/debugger communica- internal regulator if the application must operate over a tions to the device. If such discrete components are an wide temperature range. application requirement, they should be removed from In addition to temperature tolerance, the effective the circuit during programming and debugging. Alter- capacitance of large value ceramic capacitors can vary natively, refer to the AC/DC characteristics and timing substantially, based on the amount of DC voltage requirements information in the respective device applied to the capacitor. This effect can be very signifi- Flash programming specification for information on cant, but is often overlooked or is not always capacitive loading limits, and Voltage Input High (VIH) documented. pin and Voltage Input Low (VIL) pin requirements. A typical DC bias voltage vs. capacitance graph for For device emulation, ensure that the “Communication X7R type capacitors is shown in Figure2-4. Channel Select” (i.e., PGCx/PGDx pins), programmed into the device, matches the physical connections for the ICSP to the Microchip debugger/emulator tool. For more information on available Microchip development tools connection requirements, refer to Section27.0 “Development Support”. DS30009995E-page 26  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 2.6 External Oscillator Pins FIGURE 2-5: SUGGESTED PLACEMENT OF THE OSCILLATOR Many microcontrollers have options for at least two CIRCUIT oscillators: a high-frequency primary oscillator and a low-frequency secondary oscillator (refer to Section9.0 Single-Sided and In-Line Layouts: “Oscillator Configuration” for details). Copper Pour Primary Oscillator The oscillator circuit should be placed on the same (tied to ground) Crystal side of the board as the device. Place the oscillator DEVICE PINS circuit close to the respective oscillator pins with no more than 0.5 inch (12 mm) between the circuit components and the pins. The load capacitors should be placed next to the oscillator itself, on the same side Primary OSC1 Oscillator of the board. C1 ` OSC2 Use a grounded copper pour around the oscillator cir- cuit to isolate it from surrounding circuits. The C2 GND grounded copper pour should be routed directly to the ` MCU ground. Do not run any signal traces or power T1OSO traces inside the ground pour. Also, if using a two-sided board, avoid any traces on the other side of the board T1OS I Timer1 Oscillator where the crystal is placed. Crystal ` Layout suggestions are shown in Figure2-5. In-line packages may be handled with a single-sided layout that completely encompasses the oscillator pins. With T1 Oscillator: C1 T1 Oscillator: C2 fine-pitch packages, it is not always possible to com- pletely surround the pins and components. A suitable solution is to tie the broken guard sections to a mirrored Fine-Pitch (Dual-Sided) Layouts: ground layer. In all cases, the guard trace(s) must be returned to ground. Top Layer Copper Pour (tied to ground) In planning the application’s routing and I/O assign- ments, ensure that adjacent port pins and other Bottom Layer signals, in close proximity to the oscillator, are benign Copper Pour (i.e., free of high frequencies, short rise and fall times, (tied to ground) and other similar noise). OSCO For additional information and design guidance on oscillator circuits, please refer to these Microchip C2 Application Notes, available at the corporate web site Oscillator (www.microchip.com): GND Crystal • AN826, “Crystal Oscillator Basics and Crystal C1 Selection for rfPIC™ and PICmicro® Devices” • AN849, “Basic PICmicro® Oscillator Design” OSCI • AN943, “Practical PICmicro® Oscillator Analysis and Design” • AN949, “Making Your Oscillator Work” 2.7 Unused I/Os DEVICE PINS Unused I/O pins should be configured as outputs and driven to a logic low state. Alternatively, connect a 1kΩ to 10 kΩ resistor to VSS on unused pins and drive the output to logic low.  2011-2017 Microchip Technology Inc. DS30009995E-page 27

PIC24FV32KA304 FAMILY NOTES: DS30009995E-page 28  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 3.0 CPU For most instructions, the core is capable of executing a data (or program data) memory read, a working Note: This data sheet summarizes the features register (data) read, a data memory write and a pro- of this group of PIC24F devices. It is not gram (instruction) memory read per instruction cycle. intended to be a comprehensive refer- As a result, three parameter instructions can be ence source. For more information on the supported, allowing trinary operations (i.e., A + B = C) CPU, refer to the “dsPIC33/PIC24 Family to be executed in a single cycle. Reference Manual”, “CPU” (DS39703). A high-speed, 17-bit by 17-bit multiplier has been included to significantly enhance the core arithmetic The PIC24F CPU has a 16-bit (data) modified Harvard capability and throughput. The multiplier supports architecture with an enhanced instruction set and a Signed, Unsigned and Mixed mode, 16-bit by 16-bit or 24-bit instruction word with a variable length opcode 8-bit by 8-bit integer multiplication. All multiply field. The Program Counter (PC) is 23 bits wide and instructions execute in a single cycle. addresses up to 4M instructions of user program memory space. A single-cycle instruction prefetch The 16-bit ALU has been enhanced with integer divide mechanism is used to help maintain throughput and assist hardware that supports an iterative non-restoring provides predictable execution. All instructions execute divide algorithm. It operates in conjunction with the in a single cycle, with the exception of instructions that REPEAT instruction looping mechanism and a selection change the program flow, the double-word move of iterative divide instructions to support 32-bit (or (MOV.D) instruction and the table instructions. 16-bit), divided by 16-bit integer signed and unsigned Overhead-free program loop constructs are supported division. All divide operations require 19 cycles to using the REPEAT instructions, which are interruptible complete but are interruptible at any cycle boundary. at any point. The PIC24F has a vectored exception scheme with up PIC24F devices have sixteen, 16-bit Working registers to eight sources of non-maskable traps and up to in the programmer’s model. Each of the Working 118interrupt sources. Each interrupt source can be registers can act as a data, address or address offset assigned to one of seven priority levels. register. The 16th Working register (W15) operates as A block diagram of the CPU is illustrated in Figure3-1. a Software Stack Pointer (SSP) for interrupts and calls. The upper 32Kbytes of the data space memory map 3.1 Programmer’s Model can optionally be mapped into program space at any 16K word boundary of either program memory or data Figure3-2 displays the programmer’s model for the EEPROM memory, defined by the 8-bit Program Space PIC24F. All registers in the programmer’s model are Visibility Page Address (PSVPAG) register. The memory mapped and can be manipulated directly by program to data space mapping feature lets any instructions. instruction access program space as if it were data Table3-1 provides a description of each register. All space. registers associated with the programmer’s model are The Instruction Set Architecture (ISA) has been signifi- memory mapped. cantly enhanced beyond that of the PIC18, but maintains an acceptable level of backward compatibil- ity. All PIC18 instructions and addressing modes are supported, either directly, or through simple macros. Many of the ISA enhancements have been driven by compiler efficiency needs. The core supports Inherent (no operand), Relative, Literal, Memory Direct and three groups of addressing modes. All modes support Register Direct and various Register Indirect modes. Each group offers up to seven addressing modes. Instructions are associated with predefined addressing modes depending upon their functional requirements.  2011-2017 Microchip Technology Inc. DS30009995E-page 29

PIC24FV32KA304 FAMILY FIGURE 3-1: PIC24F CPU CORE BLOCK DIAGRAM PSV and Table Data Access Control Block Data Bus Interrupt Controller 16 8 16 16 Data Latch 23 PCH PCL Data RAM 16 23 Program Counter Stack Loop Address Control Control Latch Logic Logic 23 16 RAGU Address Latch WAGU Program Memory Data EEPROM Address Bus EA MUX Data Latch ROM Latch 24 16 16 Instruction a Decode and at D Control Instruction Reg al er Lit Control Signals to Various Blocks Hardware Multiplier 16 x 16 W Register Array Divide Support 16 16-Bit ALU 16 To Peripheral Modules TABLE 3-1: CPU CORE REGISTERS Register(s) Name Description W0 through W15 Working Register Array PC 23-Bit Program Counter SR ALU STATUS Register SPLIM Stack Pointer Limit Value Register TBLPAG Table Memory Page Address Register PSVPAG Program Space Visibility Page Address Register RCOUNT Repeat Loop Counter Register CORCON CPU Control Register DS30009995E-page 30  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY FIGURE 3-2: PROGRAMMER’S MODEL 15 0 W0 (WREG) Divider Working Registers W1 W2 Multiplier Registers W3 W4 W5 W6 W7 Working/Address W8 Registers W9 W10 W11 W12 W13 W14 Frame Pointer W15 Stack Pointer 0 Stack Pointer Limit SPLIM 0 Value Register 22 0 PC 0 Program Counter 7 0 Table Memory Page TBLPAG Address Register 7 0 Program Space Visibility PSVPAG Page Address Register 15 0 Repeat Loop Counter RCOUNT Register 15 SRH SRL 0 ———————DC IPL RA N OV Z C ALU STATUS Register (SR) 2 1 0 15 0 ————————————IPL3PSV—— CPU Control Register (CORCON) Registers or bits are shadowed for PUSH.S and POP.S instructions.  2011-2017 Microchip Technology Inc. DS30009995E-page 31

PIC24FV32KA304 FAMILY 3.2 CPU Control Registers REGISTER 3-1: SR: ALU STATUS REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0, HSC — — — — — — — DC bit 15 bit 8 R/W-0, HSC(1) R/W-0, HSC(1) R/W-0, HSC(1) R-0, HSC R/W-0, HSC R/W-0, HSC R/W-0, HSC R/W-0, HSC IPL2(2) IPL1(2) IPL0(2) RA N OV Z C bit 7 bit 0 Legend: HSC = Hardware Settable/Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-9 Unimplemented: Read as ‘0’ bit 8 DC: ALU Half Carry/Borrow bit 1 = A carry-out from the 4th low-order bit (for byte-sized data) or 8th low-order bit (for word-sized data) of the result occurred 0 = No carry-out from the 4th or 8th low-order bit of the result has occurred bit 7-5 IPL<2:0>: CPU Interrupt Priority Level Status bits(1,2) 111 = CPU Interrupt Priority Level is 7 (15); user interrupts are disabled 110 = CPU Interrupt Priority Level is 6 (14) 101 = CPU Interrupt Priority Level is 5 (13) 100 = CPU Interrupt Priority Level is 4 (12) 011 = CPU Interrupt Priority Level is 3 (11) 010 = CPU Interrupt Priority Level is 2 (10) 001 = CPU Interrupt Priority Level is 1 (9) 000 = CPU Interrupt Priority Level is 0 (8) bit 4 RA: REPEAT Loop Active bit 1 = REPEAT loop in progress 0 = REPEAT loop not in progress bit 3 N: ALU Negative bit 1 = Result was negative 0 = Result was non-negative (zero or positive) bit 2 OV: ALU Overflow bit 1 = Overflow occurred for signed (2’s complement) arithmetic in this arithmetic operation 0 = No overflow has occurred bit 1 Z: ALU Zero bit 1 = An operation, which effects the Z bit, has set it at some time in the past 0 = The most recent operation, which effects the Z bit, has cleared it (i.e., a non-zero result) bit 0 C: ALU Carry/Borrow bit 1 = A carry-out from the Most Significant bit (MSb) of the result occurred 0 = No carry-out from the Most Significant bit (MSb) of the result occurred Note 1: The IPLx Status bits are read-only when NSTDIS (INTCON1<15>) = 1. 2: The IPL<2:0> Status bits are concatenated with the IPL3 bit (CORCON<3>) to form the CPU Interrupt Priority Level (IPL). The value in parentheses indicates the IPL when IPL3 = 1. DS30009995E-page 32  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 3-2: CORCON: CPU CONTROL REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 U-0 U-0 R/C-0, HSC R/W-0 U-0 U-0 — — — — IPL3(1) PSV — — bit 7 bit 0 Legend: C = Clearable bit HSC = Hardware Settable/Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-4 Unimplemented: Read as ‘0’ bit 3 IPL3: CPU Interrupt Priority Level Status bit(1) 1 = CPU Interrupt Priority Level is greater than 7 0 = CPU Interrupt Priority Level is 7 or less bit 2 PSV: Program Space Visibility in Data Space Enable bit 1 = Program space is visible in data space 0 = Program space is not visible in data space bit 1-0 Unimplemented: Read as ‘0’ Note 1: User interrupts are disabled when IPL3 = 1. 3.3 Arithmetic Logic Unit (ALU) The PIC24F CPU incorporates hardware support for both multiplication and division. This includes a The PIC24F ALU is 16 bits wide and is capable of dedicated hardware multiplier and support hardware addition, subtraction, bit shifts and logic operations. division for 16-bit divisor. Unless otherwise mentioned, arithmetic operations are 2’s complement in nature. Depending on the operation, 3.3.1 MULTIPLIER the ALU may affect the values of the Carry (C), Zero The ALU contains a high-speed, 17-bit x 17-bit (Z), Negative (N), Overflow (OV) and Digit Carry (DC) multiplier. It supports unsigned, signed or mixed sign Status bits in the SR register. The C and DC Status bits operation in several multiplication modes: operate as Borrow and Digit Borrow bits, respectively, for subtraction operations. • 16-bit x 16-bit signed The ALU can perform 8-bit or 16-bit operations, • 16-bit x 16-bit unsigned depending on the mode of the instruction that is used. • 16-bit signed x 5-bit (literal) unsigned Data for the ALU operation can come from the W • 16-bit unsigned x 16-bit unsigned register array, or data memory, depending on the • 16-bit unsigned x 5-bit (literal) unsigned addressing mode of the instruction. Likewise, output • 16-bit unsigned x 16-bit signed data from the ALU can be written to the W register array • 8-bit unsigned x 8-bit unsigned or a data memory location.  2011-2017 Microchip Technology Inc. DS30009995E-page 33

PIC24FV32KA304 FAMILY 3.3.2 DIVIDER 3.3.3 MULTI-BIT SHIFT SUPPORT The divide block supports 32-bit/16-bit and 16-bit/16-bit The PIC24F ALU supports both single bit and signed and unsigned integer divide operations with the single-cycle, multi-bit arithmetic and logic shifts. following data sizes: Multi-bit shifts are implemented using a shifter block, capable of performing up to a 15-bit arithmetic right 1. 32-bit signed/16-bit signed divide shift, or up to a 15-bit left shift, in a single cycle. All 2. 32-bit unsigned/16-bit unsigned divide multi-bit shift instructions only support Register Direct 3. 16-bit signed/16-bit signed divide Addressing for both the operand source and result 4. 16-bit unsigned/16-bit unsigned divide destination. The quotient for all divide instructions ends up in W0 A full summary of instructions that use the shift and the remainder in W1. Sixteen-bit signed and operation is provided in Table3-2. unsigned DIV instructions can specify any W register for both the 16-bit divisor (Wn), and any W register (aligned) pair (W(m + 1):Wm) for the 32-bit dividend. The divide algorithm takes one cycle per bit of divisor, so both 32-bit/16-bit and 16-bit/16-bit instructions take the same number of cycles to execute. TABLE 3-2: INSTRUCTIONS THAT USE THE SINGLE AND MULTI-BIT SHIFT OPERATION Instruction Description ASR Arithmetic shift right source register by one or more bits. SL Shift left source register by one or more bits. LSR Logical shift right source register by one or more bits. DS30009995E-page 34  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 4.0 MEMORY ORGANIZATION User access to the program memory space is restricted to the lower half of the address range (000000h to As Harvard architecture devices, the PIC24F 7FFFFFh). The exception is the use of TBLRD/TBLWT microcontrollers feature separate program and data operations, which use TBLPAG<7> to permit access to memory space and busing. This architecture also the Configuration bits and Device ID sections of the allows the direct access of program memory from the configuration memory space. data space during code execution. Memory maps for the PIC24FV32KA304 family of devices are shown in Figure4-1. 4.1 Program Address Space The program address memory space of the PIC24FV32KA304 family is 4M instructions. The space is addressable by a 24-bit value derived from either the 23-bit Program Counter (PC) during program execu- tion, or from a table operation or data space remapping, as described in Section4.3 “Interfacing Program and Data Memory Spaces”. FIGURE 4-1: PROGRAM SPACE MEMORY MAP FOR PIC24FV32KA304 FAMILY DEVICES PIC24FV16KA304 PIC24FV32KA304 GOTO Instruction GOTO Instruction 000000h 000002h Reset Address Reset Address 000004h Interrupt Vector Table Interrupt Vector Table 0000FEh Reserved Reserved 000100h Alternate Vector Table Alternate Vector Table 00000011F04Ehh 000200h Flash Program Memory e (5632 instructions) c a Sp User Flash mory (1P1r2o6g4ra imns tMruecmtioonrys) 002BFEh e M er s U Unimplemented Read ‘0’ 0057FEh Unimplemented Read ‘0’ 7FFE00h Data EEPROM Data EEPROM 7FFFFFh 800000h Reserved e Reserved c a p S y or F7FFFEh em Device Config Registers Device Config Registers F80000h M F80010h n F80012h o ati ur nfig Reserved Reserved o C FEFFFEh DEVID (2) DEVID (2) FF0000h FFFFFFh Note: Memory areas are not displayed to scale. DS30009995E-page 35  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 4.1.1 PROGRAM MEMORY 4.1.3 DATA EEPROM ORGANIZATION In the PIC24FV32KA304 family, the data EEPROM is The program memory space is organized in mapped to the top of the user program memory space, word-addressable blocks. Although it is treated as starting at address, 7FFE00, and expanding up to 24bits wide, it is more appropriate to think of each address, 7FFFFF. address of the program memory as a lower and upper The data EEPROM is organized as 16-bit wide memory word, with the upper byte of the upper word being and 256 words deep. This memory is accessed using unimplemented. The lower word always has an even Table Read and write operations similar to the user address, while the upper word has an odd address, as code memory. shown in Figure4-2. 4.1.4 DEVICE CONFIGURATION WORDS Program memory addresses are always word-aligned on the lower word, and addresses are incremented or Table4-1 provides the addresses of the device decremented by two during code execution. This Configuration Words for the PIC24FV32KA304 family. arrangement also provides compatibility with data Their location in the memory map is shown in memory space addressing and makes it possible to Figure4-1. access data in the program memory space. For more information on device Configuration Words, 4.1.2 HARD MEMORY VECTORS see Section26.0 “Special Features”. All PIC24F devices reserve the addresses between TABLE 4-1: DEVICE CONFIGURATION 00000h and 000200h for hard coded program execu- WORDS FOR PIC24FV32KA304 tion vectors. A hardware Reset vector is provided to FAMILY DEVICES redirect code execution from the default value of the PC on device Reset to the actual start of code. A GOTO Configuration Word Configuration Words instruction is programmed by the user at 000000h, with Addresses the actual address for the start of code at 000002h. FBS F80000 PIC24F devices also have two Interrupt Vector Tables, FGS F80004 located from 000004h to 0000FFh and 000104h to 0001FFh. These vector tables allow each of the many FOSCSEL F80006 device interrupt sources to be handled by separate FOSC F80008 Interrupt Service Routines (ISRs). A more detailed FWDT F8000A discussion of the Interrupt Vector Tables (IVT) is FPOR F8000C provided in Section8.1 “Interrupt Vector Table (IVT)”. FICD F8000E FDS F80010 FIGURE 4-2: PROGRAM MEMORY ORGANIZATION msw most significant word least significant word PC Address Address (lsw Address) 23 16 8 0 000001h 00000000 000000h 000003h 00000000 000002h 000005h 00000000 000004h 000007h 00000000 000006h Program Memory Instruction Width ‘Phantom’ Byte (read as ‘0’)  2011-2017 Microchip Technology Inc. DS30009995E-page 36

PIC24FV32KA304 FAMILY 4.2 Data Address Space PIC24FV32KA304 family devices implement a total of 1024words of data memory. If an EA points to a The PIC24F core has a separate, 16-bit wide data location outside of this area, an all zero word or byte will memory space, addressable as a single linear range. be returned. The data space is accessed using two Address Generation Units (AGUs), one each for read and write 4.2.1 DATA SPACE WIDTH operations. The data space memory map is shown in The data memory space is organized in Figure4-3. byte-addressable, 16-bit wide blocks. Data is aligned in All Effective Addresses (EAs) in the data memory space data memory and registers as 16-bit words, but all the are 16 bits wide and point to bytes within the data space. data space EAs resolve to bytes. The Least Significant This gives a data space address range of 64 Kbytes or Bytes (LSBs) of each word have even addresses, while 32Kwords. The lower half of the data memory space the Most Significant Bytes (MSBs) have odd (that is, when EA<15> = 0) is used for implemented addresses. memory addresses, while the upper half (EA<15> = 1) is reserved for the Program Space Visibility (PSV) area (see Section4.3.3 “Reading Data from Program Memory Using Program Space Visibility”). FIGURE 4-3: DATA SPACE MEMORY MAP FOR PIC24FV32KA304 FAMILY DEVICES MSB LSB Address MSB LSB Address 0001h SFR Space 0000h SFR 07FFh 07FEh Space 0801h 0800h Implemented Data RAM Near Data RAM Data Space 0FFFh 0FFEh 1FFF 1FFEh Unimplemented Read as ‘0’ 7FFFh 7FFFh 8001h 8000h Program Space Visibility Area FFFFh FFFEh Note: Data memory areas are not shown to scale. DS30009995E-page 37  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 4.2.2 DATA MEMORY ORGANIZATION can clear the MSB of any W register by executing a AND ALIGNMENT Zero-Extend (ZE) instruction on the appropriate address. To maintain backward compatibility with PIC® MCU devices and improve data space memory usage Although most instructions are capable of operating on efficiency, the PIC24F instruction set supports both word or byte data sizes, it should be noted that some word and byte operations. As a consequence of byte instructions operate only on words. accessibility, all Effective Address (EA) calculations are 4.2.3 NEAR DATA SPACE internally scaled to step through word-aligned memory. For example, the core recognizes that Post-Modified The 8-Kbyte area between 0000h and 1FFFh is Register Indirect Addressing mode [Ws++] will result in referred to as the Near Data Space (NDS). Locations in a value of Ws + 1 for byte operations and Ws + 2 for this space are directly addressable via a 13-bit abso- word operations. lute address field within all memory direct instructions. The remainder of the data space is addressable Data byte reads will read the complete word, which indirectly. Additionally, the whole data space is contains the byte, using the LSB of any EA to determine which byte to select. The selected byte is addressable using MOV instructions, which support Memory Direct Addressing (MDA) with a 16-bit address placed onto the LSB of the data path. That is, data field. For PIC24FV32KA304 family devices, the entire memory and the registers are organized as two implemented data memory lies in Near Data Space. parallel, byte-wide entities with shared (word) address decode, but separate write lines. Data byte writes only 4.2.4 SFR SPACE write to the corresponding side of the array or register, which matches the byte address. The first 2 Kbytes of the Near Data Space, from 0000h to 07FFh, are primarily occupied with Special Function All word accesses must be aligned to an even address. Registers (SFRs). These are used by the PIC24F core Misaligned word data fetches are not supported, so and peripheral modules for controlling the operation of care must be taken when mixing byte and word the device. operations, or translating from 8-bit MCU code. If a misaligned read or write is attempted, an address error SFRs are distributed among the modules that they trap will be generated. If the error occurred on a read, control and are generally grouped together by the the instruction underway is completed; if it occurred on module. Much of the SFR space contains unused a write, the instruction will be executed, but the write addresses; these are read as ‘0’. The SFR space, will not occur. In either case, a trap is then executed, where the SFRs are actually implemented, is provided allowing the system and/or user to examine the in Table4-2. Each implemented area indicates a machine state prior to execution of the address Fault. 32-byte region, where at least one address is implemented as an SFR. A complete listing of All byte loads into any W register are loaded into the implemented SFRs, including their addresses, is LSB; the MSB is not modified. provided in Table4-3 throughTable4-25. A Sign-Extend (SE) instruction is provided to allow the users to translate 8-bit signed data to 16-bit signed values. Alternatively, for 16-bit unsigned data, users TABLE 4-2: IMPLEMENTED REGIONS OF SFR DATA SPACE SFR Space Address xx00 xx20 xx40 xx60 xx80 xxA0 xxC0 xxE0 000h Core ICN Interrupts — 100h Timers Capture — Compare — — — 200h I2C UART SPI — — I/O 300h A/D/CMTU — — — — 400h — — — — — — — — 500h — — — — — — — — 600h — RTC/Comp CRC — — 700h — — System/DS/HLVD NVM/PMD — — — — Legend: — = No implemented SFRs in this block.  2011-2017 Microchip Technology Inc. DS30009995E-page 38

D TABLE 4-3: CPU CORE REGISTERS MAP P S 30 File Start All I 0 Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 C 0 Name Addr Resets 9 9 2 9 WREG0 0000 WREG0 0000 5E 4 -p WREG1 0002 WREG1 0000 F a g WREG2 0004 WREG2 0000 e V 3 WREG3 0006 WREG3 0000 9 3 WREG4 0008 WREG4 0000 2 WREG5 000A WREG5 0000 K WREG6 000C WREG6 0000 A WREG7 000E WREG7 0000 WREG8 0010 WREG8 0000 3 WREG9 0012 WREG9 0000 0 4 WREG10 0014 WREG10 0000 WREG11 0016 WREG11 0000 F WREG12 0018 WREG12 0000 A WREG13 001A WREG13 0000 M WREG14 001C WREG14 0000 I WREG15 001E WREG15 0000 L SPLIM 0020 SPLIM xxxx Y PCL 002E PCL 0000 PCH 0030 — — — — — — — — — PCH 0000 TBLPAG 0032 — — — — — — — — TBLPAG 0000 PSVPAG 0034 — — — — — — — — PSVPAG 0000 RCOUNT 0036 RCOUNT xxxxx SR 0042 — — — — — — — DC IPL2 IPL1 IPL0 RA N OV Z C 0000 CORCON 0044 — — — — — — — — — — — — IPL3 PSV — — 0000  DISICNT 0052 — — DISICNT xxxx 2 0 Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. 1 1 -2 0 1 7 M ic ro c h ip T e c h n o lo g y In c .

TABLE 4-4: ICN REGISTER MAP  2 0 File All 1 Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 1 Name Resets -2 01 CNPD1 0056 CN15PDE(1) CN14PDE CN13PDE CN12PDE CN11PDE CN10PDE(1,2) CN9PDE(1) CN8PDE(3) CN7PDE(1) CN6PDE CN5PDE CN4PDE CN3PDE CN2PDE CN1PDE CN0PDE 0000 7 M CNPD2 0058 CN31PDE(1,2) CN30PDE CN29PDE CN28PDE(1,2) CN27PDE(1) CN26PDE(1,2) CN25PDE(1,2) CN24PDE(1) CN23PDE CN22PDE CN21PDE CN20PDE(1,2) CN19PDE(1,2) CN18PDE(1,2) CN17PDE(1,2) CN16PDE(1) 0000 icro CNPD3 005A — — — — — — — — — — — CN36PDE(1,2) CN35PDE(1,2) CN34PDE(1,2) CN33PDE(1,2) CN32PDE(1,2) 0000 ch CNEN1 0062 CN15IE(1) CN14IE CN13IE CN12IE CN11IE CN10IE(1,2) CN9IE(1) CN8IE(3) CN7IE(1) CN6IE CN5IE CN4IE CN3IE CN2IE CN1IE CN0IE 0000 ip T CNEN2 0064 CN31IE(1,2) CN30IE CN29IE CN28IE(1,2) CN27IE(1) CN26IE(1,2) CN25IE(1,2) CN24IE(1) CN23IE CN22IE CN21IE CN20IE(1,2) CN19IE(1,2) CN18IE(1,2) CN17IE(1,2) CN16IE(1) 0000 e ch CNEN3 0066 — — — — — — — — — — — CN36IE(1,2) CN35IE(1,2) CN34IE(1,2) CN33IE(1,2) CN32IE(1,2) 0000 n o CNPU1 006E CN15PUE(1) CN14PUE CN13PUE CN12PUE CN11PUE CN10PUE(1,2) CN9PUE(1) CN8PUE(3) CN7PUE(1) CN6PUE CN5PUE CN4PUE CN3PUE CN2PUE CN1PUE CN0PUE 0000 lo gy CNPU2 0070 CN31PUE(1,2) CN30PUE CN29PUE CN28PUE(1,2) CN27PUE(1) CN26PUE(1,2) CN25PUE(1,2) CN24PUE(1) CN23PUE CN22PUE CN21PUE CN20PUE(1,2) CN19PUE(1,2) CN18PUE(1,2) CN17PUE(1,2) CN16PUE(1) 0000 Inc CNPU3 0072 — — — — — — — — — — — CN36PUE(1,2) CN35PUE(1,2) CN34PUE(1,2) CN33PUE(1,2) CN32PUE(1,2) 0000 . Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. Note 1: These bits are not implemented in 20-pin devices. 2: These bits are not implemented in 28-pin devices. 3: These bits are not implemented in FV devices. P I C 2 4 F V 3 2 K A 3 0 4 D S 3 F 0 00 A 9 9 9 M 5 E -p I a L g e 4 Y 0

D TABLE 4-5: INTERRUPT CONTROLLER REGISTER MAP P S 3000 NFaimlee Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 ReAslel ts IC 9 9 2 95E INTCON1 0080 NSTDIS — — — — — — — — — — MATHERR ADDRERR STKERR OSCFAIL — 0000 4 -p INTCON2 0082 ALTIVT DISI — — — — — — — — — — — INT2EP INT1EP INT0EP 0000 F a ge IFS0 0084 NVMIF — AD1IF U1TXIF U1RXIF SPI1IF SPF1IF T3IF T2IF OC2IF IC2IF — T1IF OC1IF IC1IF INT0IF 0000 V 41 IFS1 0086 U2TXIF U2RXIF INT2IF T5IF T4IF — OC3IF — — — — INT1IF CNIF CMIF MI2C1IF SI2C1IF 0000 3 IFS2 0088 — — — — — — — — — — IC3IF — — — SPI2IF SPF2IF 0000 2 IFS3 008A — RTCIF — — — — — — — — — — — MI2C2IF SI2C2IF — 0000 K IFS4 008C — — CTMUIF — — — — HLVDIF — — — — CRCIF U2ERIF U1ERIF — 0000 A IFS5 008E — — — — — — — — — — — — — — — ULPWUIF 0000 3 IEC0 0094 NVMIE — AD1IE U1TXIE U1RXIE SPI1IE SPF1IE T3IE T2IE OC2IE IC2IE — T1IE OC1IE IC1IE INT0IE 0000 0 IEC1 0096 U2TXIE U2RXIE INT2IE T5IE T4IE — OC3IE — — — — INT1IE CNIE CMIE MI2C1IE SI2C1IE 0000 4 IEC2 0098 — — — — — — — — — — IC3IE — — — SPI2IE SPF2IE 0000 IEC3 009A — RTCIE — — — — — — — — — — — MI2C2IE SI2C2IE — 0000 F IEC4 009C — — CTMUIE — — — — HLVDIE — — — — CRCIE U2ERIE U1ERIE — 0000 A IEC5 009E — — — — — — — — — — — — — — — ULPWUIE 0000 M IPC0 00A4 — T1IP2 T1IP1 T1IP0 — OC1IP2 OC1IP1 OC1IP0 — IC1IP2 IC1IP1 IC1IP0 — INT0IP2 INT0IP1 INT0IP0 4444 I IPC1 00A6 — T2IP2 T2IP1 T2IP0 — OC2IP2 OC2IP1 OC2IP0 — IC2IP2 IC2IP1 IC2IP0 — — — — 4444 L IPC2 00A8 — U1RXIP2 U1RXIP1 U1RXIP0 — SPI1IP2 SPI1IP1 SPI1IP0 — SPF1IP2 SPF1IP1 SPF1IP0 — T3IP2 T3IP1 T3IP0 4444 Y IPC3 00AA — NVMIP2 NVMIP1 NVMIP0 — — — — — AD1IP2 AD1IP1 AD1IP0 — U1TXIP2 U1TXIP1 U1TXIP0 4044 IPC4 00AC — CNIP2 CNIP1 CNIP0 — CMIP2 CMIP1 CMIP0 — MI2C1P2 MI2C1P1 MI2C1P0 — SI2C1P2 SI2C1P1 SI2C1P0 4444 IPC5 00AE — — — — — — — — — — — — — INT1IP2 INT1IP1 INT1IP0 0004 IPC6 00B0 — T4IP2 T4IP1 T4IP0 — — — — — OC3IP2 OC3IP1 OC3IP0 — — — — 4040 IPC7 00B2 — U2TXIP2 U2TXIP1 U2TXIP0 — U2RXIP2 U2RXIP1 U2RXIP0 — INT2IP2 INT2IP1 INT2IP0 — T5IP2 T5IP1 T5IP0 4440 IPC8 00B4 — — — — — — — — — SPI2IP2 SPI2IP1 SPI2IP0 — SPF2IP2 SPF2IP1 SPF2IP0 0044 IPC9 00B6 — — — — — — — — — IC3IP2 IC3IP1 IC3IP0 — — — — 0040  IPC12 00BC — — — — — MI2C2IP2 MI2C2IP1 MI2C2IP0 — SI2C2IP2 SI2C2IP1 SI2C2IP0 — — — — 0440 2 01 IPC15 00C2 — — — — — RTCIP2 RTCIP1 RTCIP0 — — — — — — — — 0400 1 -2 IPC16 00C4 — CRCIP2 CRCIP1 CRCIP0 — U2ERIP2 U2ERIP1 U2ERIP0 — U1ERIP2 U1ERIP1 U1ERIP0 — — — — 4440 0 1 IPC18 00C8 — — — — — — — — — — — — — HLVDIP2 HLVDIP1 HLVDIP0 0004 7 M IPC19 00CA — — — — — — — — — CTMUIP2 CTMUIP1 CTMUIP0 — — — — 0040 ic ro IPC20 00CC — — — — — — — — — — — — — ULPWUIP2 ULPWUIP1 ULPWUIP0 0000 c hip INTTREG 00E0 CPUIRQ — VHOLD — ILR3 ILR2 ILR1 ILR0 — VECNUM6 VECNUM5 VECNUM4 VECNUM3 VECNUM2 VECNUM1 VECNUM0 0000 T Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. e c h n o lo g y In c .

 TABLE 4-6: TIMER REGISTER MAP 2 0 File All 1 Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 1 Name Resets -2 0 1 TMR1 0100 TMR1 0000 7 M PR1 0102 PR1 FFFF ic ro T1CON 0104 TON — TSIDL — — — T1ECS1 T1ECS0 — TGATE TCKPS1 TCKPS0 — TSYNC TCS — 0000 c h TMR2 0106 TMR2 0000 ip T TMR3HLD 0108 TMR3HLD 0000 e ch TMR3 010A TMR3 0000 n olo PR2 010C PR2 0000 gy PR3 010E PR3 FFFF Inc T2CON 0110 TON — TSIDL — — — — — — TGATE TCKPS1 TCKPS0 T32 — TCS — FFFF . T3CON 0112 TON — TSIDL — — — — — — TGATE TCKPS1 TCKPS0 — — TCS — 0000 TMR4 0114 TMR4 0000 TMR5HLD 0116 TMR5HLD 0000 TMR5 0118 TMR5 0000 PR4 011A PR4 FFFF PR5 011C PR5 FFFF T4CON 011E TON — TSIDL — — — — — — TGATE TCKPS1 TCKPS0 T45 — TCS — 0000 P T5CON 0120 TON — TSIDL — — — — — — TGATE TCKPS1 TCKPS0 — — TCS — 0000 I Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. C 2 TABLE 4-7: INPUT CAPTURE REGISTER MAP 4 F File All Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Name Resets V IC1CON1 0140 — — ICSIDL ICTSEL2 ICTSEL1 ICTSEL0 — — — ICI1 ICI0 ICOV ICBNE ICM2 ICM1 ICM0 0000 3 2 IC1CON2 0142 — — — — — — — IC32 ICTRIG TRIGSTAT — SYNCSEL4 SYNCSEL3 SYNCSEL2 SYNCSEL1 SYNCSEL0 000D K IC1BUF 0144 IC1BUF 0000 IC1TMR 0146 IC1TMR xxxx A IC2CON1 0148 — — ICSIDL IC2TSEL2 IC2TSEL1 IC2TSEL0 — — — ICI1 ICI0 ICOV ICBNE ICM2 ICM1 ICM0 0000 3 IC2CON2 014A — — — — — — — IC32 ICTRIG TRIGSTAT — SYNCSEL4 SYNCSEL3 SYNCSEL2 SYNCSEL1 SYNCSEL0 000D 0 IC2BUF 014C IC2BUF 0000 4 D S IC2TMR 014E IC2TMR xxxx 3 F 000 IC3CON1 0150 — — ICSIDL IC3TSEL2 IC3TSEL1 IC3TSEL0 — — — ICI1 ICI0 ICOV ICBNE ICM2 ICM1 ICM0 0000 A 99 IC3CON2 0152 — — — — — — — IC32 ICTRIG TRIGSTAT — SYNCSEL4 SYNCSEL3 SYNCSEL2 SYNCSEL1 SYNCSEL0 000D 9 M 5 IC3BUF 0154 IC3BUF 0000 E -p IC3TMR 0156 IC3TMR xxxx I a L ge 4 Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. Y 2

D TABLE 4-8: OUTPUT COMPARE REGISTER MAP P S 3000 NFaimlee Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 ReAslel ts IC 9 9 2 9 OC1CON1 0190 — — OCSIDL OCTSEL2 OCTSEL1 OCTSEL0 ENFLT2 ENFLT1 ENFLT0 OCFLT2 OCFLT1 OCFLT0 TRIGMODE OCM2 OCM1 OCM0 0000 5E-p OC1CON2 0192 FLTMD FLTOUT FLTTRIEN OCINV — DCB1 DCB0 OC32 OCTRIG TRIGSTAT OCTRIS SYNCSEL4 SYNCSEL3 SYNCSEL2 SYNCSEL1 SYNCSEL0 000C 4F ag OC1RS 0194 OC1RS 0000 e V 4 OC1R 0196 OC1R 0000 3 3 OC1TMR 0198 OC1TMR xxxx 2 OC2CON1 019A — — OCSIDL OCTSEL2 OCTSEL1 OCTSEL0 ENFLT2 ENFLT1 ENFLT0 OCFLT2 OCFLT1 OCFLT0 TRIGMODE OCM2 OCM1 OCM0 0000 K OC2CON2 019C FLTMD FLTOUT FLTTRIEN OCINV — DCB1 DCB0 OC32 OCTRIG TRIGSTAT OCTRIS SYNCSEL4 SYNCSEL3 SYNCSEL2 SYNCSEL1 SYNCSEL0 000C A OC2RS 019E OC2RS 0000 OC2R 01A0 OC2R 0000 3 OC2TMR 01A2 OC2TMR xxxx 0 OC3CON1 01A4 — — OCSIDL OCTSEL2 OCTSEL1 OCTSEL0 ENFLT2 ENFLT1 ENFLT0 OCFLT2 OCFLT1 OCFLT0 TRIGMODE OCM2 OCM1 OCM0 0000 4 OC3CON2 01A6 FLTMD FLTOUT FLTTRIEN OCINV — DCB1 DCB0 OC32 OCTRIG TRIGSTAT OCTRIS SYNCSEL4 SYNCSEL3 SYNCSEL2 SYNCSEL1 SYNCSEL0 000C F OC3RS 01A8 OC3RS 0000 A OC3R 01AA OC3R 0000 M OC3TMR 01AC OC3TMR xxxx Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. IL Y  2 0 1 1 -2 0 1 7 M ic ro c h ip T e c h n o lo g y In c .

TABLE 4-9: I2Cx REGISTER MAP  2 0 File All 1 Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 1 Name Resets -2 01 I2C1RCV 0200 — — — — — — — — I2CRCV 0000 7 M I2C1TRN 0202 — — — — — — — — I2CTRN 00FF ic ro I2C1BRG 0204 — — — — — — — — I2CBRG 0000 c h I2C1CON 0206 I2CEN — I2CSIDL SCLREL IPMIEN A10M DISSLW SMEN GCEN STREN ACKDT ACKEN RCEN PEN RSEN SEN 1000 ip T I2C1STAT 0208 ACKSTAT TRSTAT — — — BCL GCSTAT ADD10 IWCOL I2COV D/A P S R/W RBF TBF 0000 e ch I2C1ADD 020A — — — — — — I2CADD 0000 n olo I2C1MSK 020C — — — — — — AMSK<9:0> 0000 g y I2C2RCV 0210 — — — — — — — — I2CRCV 0000 Inc I2C2TRN 0212 — — — — — — — — I2CTRN 00FF . I2C2BRG 0214 — — — — — — — — I2CBRG 0000 I2C2CON 0216 I2CEN — I2CSIDL SCLREL IPMIEN A10M DISSLW SMEN GCEN STREN ACKDT ACKEN RCEN PEN RSEN SEN 1000 I2C2STAT 0218 ACKSTAT TRSTAT — — — BCL GCSTAT ADD10 IWCOL I2COV D/A P S R/W RBF TBF 0000 I2C2ADD 021A — — — — — — I2CADD 0000 I2C2MSK 021C — — — — — — AMSK<9:0> 0000 Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. P TABLE 4-10: UARTx REGISTER MAP I C File All Name Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Resets 2 4 U1MODE 0220 UARTEN — USIDL IREN RTSMD — UEN1 UEN0 WAKE LPBACK ABAUD RXINV BRGH PDSEL1 PDSEL0 STSEL 0000 F U1STA 0222 UTXISEL1 UTXINV UTXISEL0 — UTXBRK UTXEN UTXBF TRMT URXISEL1 URXISEL0 ADDEN RIDLE PERR FERR OERR URXDA 0110 V U1TXREG 0224 — — — — — — — U1TXREG xxxx 3 U1RXREG 0226 — — — — — — — U1RXREG 0000 2 U1BRG 0228 BRG 0000 K U2MODE 0230 UARTEN — USIDL IREN RTSMD — UEN1 UEN0 WAKE LPBACK ABAUD RXINV BRGH PDSEL1 PDSEL0 STSEL 0000 A U2STA 0232 UTXISEL1 UTXINV UTXISEL0 — UTXBRK UTXEN UTXBF TRMT URXISEL1 URXISEL0 ADDEN RIDLE PERR FERR OERR URXDA 0110 U2TXREG 0234 — — — — — — — U2TXREG xxxx 3 0 U2RXREG 0236 — — — — — — — U2RXREG 0000 4 D U2BRG 0238 BRG 0000 S 3 Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. F 0 00 A 9 9 9 M 5 E -p I a L g e 4 Y 4

D P S TABLE 4-11: SPIx REGISTER MAP 30 I 0 File All C 0 Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 9 Name Resets 9 2 9 5E SPI1STAT 0240 SPIEN — SPISIDL — — SPIBEC2 SPIBEC1 SPIBEC0 SRMPT SPIROV SR1MPT SISEL2 SISEL1 SISEL0 SPITBF SPIRBF 0000 4 -p SPI1CON1 0242 — — — DISSCK DISSDO MODE16 SMP CKE SSEN CKP MSTEN SPRE2 SPRE1 SPRE0 PPRE1 PPRE0 0000 F a g e SPI1CON2 0244 FRMEN SPIFSD SPIFPOL — — — — — — — — — — — SPIFE SPIBEN 0000 V 4 5 SPI1BUF 0248 SPI1BUF 0000 3 SPI2STAT 0260 SPIEN — SPISIDL — — SPIBEC2 SPIBEC1 SPIBEC0 SRMPT SPIROV SRXMPT SISEL2 SISEL1 SISEL0 SPITBF SPIRBF 0000 2 SPI2CON1 0262 — — — DISSCK DISSDO MODE16 SMP CKE SSEN CKP MSTEN SPRE2 SPRE1 SPRE0 PPRE1 PPRE0 0000 K SPI2CON2 0264 FRMEN SPIFSD SPIFPOL — — — — — — — — — — — SPIFE SPIBEN 0000 A SPI2BUF 0268 SPI2BUF 0000 3 Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. 0 4 TABLE 4-12: PORTA REGISTER MAP F File Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11(2,3) Bit 10(2,3) Bit 9(2,3) Bit 8(2,3) Bit 7(2) Bit 6(4) Bit 5(1) Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All A Name Resets M TRISA 02C0 — — — — TRISA<11:6> — TRISA<4:0> 00DF PORTA 02C2 — — — — RA<11:0> xxxx I L LATA 02C4 — — — — LATA<11:6> — LATA<4:0> xxxx Y ODCA 02C6 — — — — ODA<11:6> — ODA<4:0> 0000 Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. Note1: This bit is available only when MCLRE=1. 2: These bits are not implemented in 20-pin devices. 3: These bits are not implemented in 28-pin devices. 4: These bits are not implemented in FV devices. TABLE 4-13: PORTB REGISTER MAP  2 NFaimlee Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11(1) Bit 10(1) Bit 9 Bit 8 Bit 7 Bit 6(1) Bit 5(1) Bit 4 Bit 3(1) Bit 2 Bit 1 Bit 0 ReAslel ts 0 1 1-2 TRISB 02C8 TRISB<15:0> FFFF 01 PORTB 02CA RB<15:0> xxxx 7 M LATB 02CC LATB<15:0> xxxx icro ODCB 02CE ODB<15:0> 0000 c h Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. ip T Note1: These bits are not implemented in 20-pin devices. e c h n o lo g y In c .

 2 TABLE 4-14: PORTC REGISTER MAP(1) 0 11-2 NFaimlee Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 ReAslel ts 0 1 7 TRISC 02D0 — — — — — — TRISC<9:0> 03FF M ic PORTC 02D2 — — — — — — RC<9:0> xxxx roc LATC 02D4 — — — — — — LATC<9:0> xxxx h ip ODCC 02D6 — — — — — — ODC<9:0> 0000 T e Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. c hn Note1: PORTC is not implemented in 20-pin devices or 28-pin devices. o lo g y In TABLE 4-15: PAD CONFIGURATION REGISTER MAP c . File Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All Resets Name PADCFG1 02FC — — — — — — — — — — SMBUSDEL<2:1> — — — — 0000 Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. P I C 2 4 F V 3 2 K A 3 0 4 D S 3 F 0 00 A 9 9 9 M 5 E -p I a L g e 4 Y 6

D TABLE 4-16: A/D REGISTER MAP P S 30 File All I 00 Name Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Resets C 9 9 2 9 ADC1BUF0 0300 ADC1BUF0 xxxx 5E 4 -p ADC1BUF1 0302 ADC1BUF1 xxxx F ag ADC1BUF2 0304 ADC1BUF2 xxxx e V 4 ADC1BUF3 0306 ADC1BUF3 xxxx 7 3 ADC1BUF4 0308 ADC1BUF4 xxxx 2 ADC1BUF5 030A ADC1BUF5 xxxx K ADC1BUF6 030C ADC1BUF6 xxxx A ADC1BUF7 030E ADC1BUF7 xxxx ADC1BUF8 0310 ADC1BUF8 xxxx 3 ADC1BUF9 0312 ADC1BUF9 xxxx 0 4 ADC1BUF10 0314 ADC1BUF10 xxxx ADC1BUF11 0316 ADC1BUF11 xxxx F ADC1BUF12 0318 ADC1BUF12 xxxx A ADC1BUF13 031A ADC1BUF13 xxxx M ADC1BUF14 031C ADC1BUF14 xxxx I ADC1BUF15 031E ADC1BUF15 xxxx L ADC1BUF16 0320 ADC1BUF16 xxxx Y ADC1BUF17 0322 ADC1BUF17 xxxx AD1CON1 0340 ADON — ADSIDL — — MODE12 FORM1 FORM0 SSRC3 SSRC2 SSRC1 SSRC0 — ASAM SAMP DONE 0000 AD1CON2 0342 PVCFG1 PVCFG0 NVCFG0 — BUFREGEN CSCNA — — BUFS SMPI4 SMPI3 SMPI2 SMPI1 SMPI0 BUFM ALTS 0000 AD1CON3 0344 ADRC EXTSAM — SAMC4 SAMC3 SAMC2 SAMC1 SAMC0 ADCS7 ADCS6 ADCS5 ADCS4 ADCS3 ADCS2 ADCS1 ADCS0 0000 AD1CHS 0348 CH0NB2 CH0NB1 CH0NB0 CH0SB4 CH0SB3 CH0SB2 CH0SB1 CH0SB0 CH0NA2 CH0NA1 CH0NA0 CH0SA4 CH0SA3 CH0SA2 CH0SA1 CH0SA0 0000 AD1CSSH 034E — CSSL<30:26> — — — — — — — — CSSL<17:16> 0000 AD1CSSL 0350 CSSL<15:0> 0000  AD1CON5 0354 ASEN LPEN CTMUREQ BGREQ r — ASINT1 ASINT0 — — — — WM1 WM0 CM1 CM0 0000 2 0 AD1CHITH 0356 — — — — — — — — — — — — — — CHH<17:16> 0000 1 1-2 AD1CHITL 0358 CHH<15:0> 0000 01 Legend: — = unimplemented, read as ‘0’; r = reserved. Reset values are shown in hexadecimal. 7 M ic ro c h ip T e c h n o lo g y In c .

TABLE 4-17: CTMU REGISTER MAP  2011 NFaimlee Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 ReAslel ts -2 0 CTMUCON1 035A CTMUEN — CTMUSIDL TGEN EDGEN EDGSEQEN IDISSEN CTTRIG — — — — — — — — 0000 1 7 M CTMUCON2 035C EDG1MOD EDG1POL EDG1SEL3 EDG1SEL2 EDG1SEL1 EDG1SEL0 EDG2STAT EDG1STAT EDG2EMOD EDG2POL EDG2SEL3 EDG2SEL2 EDG2SEL1 EDG2SEL0 — — 0000 icro CTMUICON 035E ITRIM5 ITRIM4 ITRIM3 ITRIM2 ITRIM1 ITRIM0 IRNG1 IRNG0 — — — — — — — — 0000 ch AD1CTMUENH 0360 — — — — — — — — — — — — — — CTMEN<17:16> 0000 ip T AD1CTMUENL 0362 CTMEN<15:0> 0000 e c Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. h n o log TABLE 4-18: ANALOG SELECT REGISTER MAP y Inc. NFaimlee Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 ReAslel ts ANSA 04E0 — — — — — — — — — — — — ANSA<3:0> 000F ANSB 04E2 ANSB<15:12> — — — — — — — ANSB<4:0>(1) F01F ANSC 04E4 — — — — — — — — — — — — — ANSC<2:0>(1,2) 0007 Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. Note1: ANSB3 and ANSC<2:0> bits are not implemented in 20-pin devices. 2: These bits are not implemented in 28-pin devices. P TABLE 4-19: REAL-TIME CLOCK AND CALENDAR REGISTER MAP I C File All Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Name Resets 2 ALRMVAL 0620 ALRMVAL xxxx 4 ALCFGRPT 0622 ALRMEN CHIME AMASK3 AMASK2 AMASK1 AMASK0 ALRMPTR1 ALRMPTR0 ARPT7 ARPT6 ARPT5 ARPT4 ARPT3 ARPT2 ARPT1 ARPT0 0000 F RTCVAL 0624 RTCVAL xxxx V RCFGCAL 0626 RTCEN — RTCWREN RTCSYNC HALFSEC RTCOE RTCPTR1 RTCPTR0 CAL7 CAL6 CAL5 CAL4 CAL3 CAL2 CAL1 CAL0 0000 3 RTCPWC 0628 PWCEN PWCPOL PWCCPRE PWCSPRE RTCCLK1 RTCCLK0 RTCOUT1 RTCOUT0 — — — — — — — — xxxx 2 Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. K A TABLE 4-20: TRIPLE COMPARATOR REGISTER MAP 3 File Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 All 0 Name Resets 4 D S CMSTAT 0630 CMIDL — — — — C3EVT C2EVT C1EVT — — — — — C3OUT C2OUT C1OUT xxxx 3 F 0 CVRCON 0632 — — — — — — — — CVREN CVROE CVRSS CVR4 CVR3 CVR2 CVR1 CVR0 0000 009 CM1CON 0634 CON COE CPOL CLPWR — — CEVT COUT EVPOL1 EVPOL0 — CREF — — CCH1 CCH0 xxxx A 9 95 CM2CON 0636 CON COE CPOL CLPWR — — CEVT COUT EVPOL1 EVPOL0 — CREF — — CCH1 CCH0 0000 M E -p CM3CON 0638 CON COE CPOL CLPWR — — CEVT COUT EVPOL1 EVPOL0 — CREF — — CCH1 CCH0 0000 I a L g Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. e 4 Y 8

D TABLE 4-21: CRC REGISTER MAP P S 30 File All I 0 Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 C 0 Name Resets 9 9 2 9 CRCCON1 0640 CRCEN — CSIDL VWORD4 VWORD3 VWORD2 VWORD1 VWORD0 CRCFUL CRCMPT CRCISEL CRCGO LENDIAN — — — 0000 5E 4 -p CRCCON2 0642 — — — DWIDTH4 DWIDTH3 DWIDTH2 DWIDTH1 DWIDTH0 — — — PLEN4 PLEN3 PLEN2 PLEN1 PLEN0 0000 F a g CRCXORL 0644 X<15:1> — 0000 e V 4 CRCXORH 0646 X<31:16> 0000 9 3 CRCDATL 0648 CRCDATL xxxx 2 CRCDATH 064A CRCDATH xxxx K CRCWDATL 064C CRCWDATL xxxx A CRCWDATH 064E CRCWDATH xxxx Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. 3 0 TABLE 4-22: CLOCK CONTROL REGISTER MAP 4 File All F Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Name Resets A RCON 0740 TRAPR IOPUWR SBOREN RETEN — DPSLP CM PMSLP EXTR SWR SWDTEN WDTO SLEEP IDLE BOR POR (Note1) M OSCCON 0742 — COSC2 COSC1 COSC0 — NOSC2 NOSC1 NOSC0 CLKLOCK — LOCK — CF SOSCDRV SOSCEN OSWEN (Note2) I CLKDIV 0744 ROI DOZE2 DOZE1 DOZE0 DOZEN RCDIV2 RCDIV1 RCDIV0 — — — — — — — — 3140 L OSCTUN 0748 — — — — — — — — — — TUN<5:0> 0000 Y REFOCON 074E ROEN — ROSSLP ROSEL RODIV3 RODIV2 RODIV1 RODIV0 — — — — — — — — 0000 HLVDCON 0756 HLVDEN — HLSIDL — — — — — VDIR BGVST IRVST — HLVDL3 HLVDL2 HLVDL1 HLVDL0 0000 Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. Note1: RCON register Reset values are dependent on the type of Reset. 2: OSCCON register Reset values are dependent on the Configuration fuses and by type of Reset. TABLE 4-23: DEEP SLEEP REGISTER MAP  File All Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 2 Name Resets 0 1 1 DSCON 0758 DSEN — — — — — — RTCCWDIS — — — — ULPWDIS DSBOR RELEASE 0000 -2 0 DSWAKE 075A — — — — — — — DSINT0 DSFLT — — DSWDT DSRTCC DSMCLR — DSPOR 0000 1 7 M DSGPR0(1) 075C DSGPR0 0000 icro DSGPR1(1) 075E DSGPR1 0000 ch Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. ip T Note1: The Deep Sleep registers, DSGPR0 and DSGPR1, are only reset on a VDD POR event. e c h n o lo g y In c .

 TABLE 4-24: NVM REGISTER MAP 2 0 11-2 NFaimlee Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 ResAeltls (1) 0 17 NVMCON 0760 WR WREN WRERR PGMONLY — — — — — ERASE NVMOP5 NVMOP4 NVMOP3 NVMOP2 NVMOP1 NVMOP0 0000 M NVMKEY 0766 — — — — — — — — NVMKEY 0000 ic ro Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. ch Note1: Reset value shown is for POR only. The value on other Reset states is dependent on the state of memory write or erase operations at the time of Reset. ip T e ch TABLE 4-25: ULTRA LOW-POWER WAKE-UP REGISTER MAP n o lo File All g Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 y Name Resets In c. ULPWCON 0768 ULPEN — ULPSIDL — — — — ULPSINK — — — — — — — — 0000 Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. TABLE 4-26: PMD REGISTER MAP File All Addr Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Name Resets PMD1 0770 T5MD T4MD T3MD T2MD T1MD — — — I2C1MD U2MD U1MD SPI2MD SPI1MD — — ADC1MD 0000 P PMD2 0772 — — — — — IC3MD IC2MD IC1MD — — — — — OC3MD OC2MD OC1MD 0000 I PMD3 0774 — — — — — CMPMD RTCCMD — CRCPMD — — — — — I2C2MD — 0000 C PMD4 0776 — — — — — — — — ULPWUMD — — EEMD REFOMD CTMUMD HLVDMD — 0000 2 Legend: — = unimplemented, read as ‘0’. Reset values are shown in hexadecimal. 4 F V 3 2 K A 3 0 4 D S 3 F 0 00 A 9 9 9 M 5 E -p I a L g e 5 Y 0

PIC24FV32KA304 FAMILY 4.2.5 SOFTWARE STACK 4.3 Interfacing Program and Data Memory Spaces In addition to its use as a Working register, the W15 register in PIC24F devices is also used as a Software The PIC24F architecture uses a 24-bit wide program Stack Pointer. The pointer always points to the first space and 16-bit wide data space. The architecture is available free word and grows from lower to higher also a modified Harvard scheme, meaning that data addresses. It predecrements for stack pops and can also be present in the program space. To use this post-increments for stack pushes, as shown in data successfully, it must be accessed in a way that Figure4-4. preserves the alignment of information in both spaces. Note that for a PC push during any CALL instruction, Apart from the normal execution, the PIC24F the MSB of the PC is zero-extended before the push, architecture provides two methods by which the ensuring that the MSB is always clear. program space can be accessed during operation: Note: A PC push during exception processing • Using table instructions to access individual bytes will concatenate the SRL register to the or words anywhere in the program space MSB of the PC prior to the push. • Remapping a portion of the program space into The Stack Pointer Limit Value (SPLIM) register, the data space, PSV associated with the Stack Pointer, sets an upper Table instructions allow an application to read or write address boundary for the stack. SPLIM is uninitialized small areas of the program memory. This makes the at Reset. As is the case for the Stack Pointer, method ideal for accessing data tables that need to be SPLIM<0> is forced to ‘0’ as all stack operations must updated from time to time. It also allows access to all be word-aligned. Whenever an EA is generated, using bytes of the program word. The remapping method W15 as a source or destination pointer, the resulting allows an application to access a large block of data on address is compared with the value in SPLIM. If the a read-only basis, which is ideal for look-ups from a contents of the Stack Pointer (W15) and the SPLIM large table of static data. It can only access the least register are equal, and a push operation is performed, significant word (lsw) of the program word. a stack error trap will not occur. The stack error trap will occur on a subsequent push operation. 4.3.1 ADDRESSING PROGRAM SPACE Thus, for example, if it is desirable to cause a stack Since the address ranges for the data and program error trap when the stack grows beyond address, 0DF6 spaces are 16 and 24 bits, respectively, a method is in RAM, initialize the SPLIM with the value, 0DF4. needed to create a 23-bit or 24-bit program address Similarly, a Stack Pointer underflow (stack error) trap is from 16-bit data registers. The solution depends on the generated when the Stack Pointer address is found to interface method to be used. be less than 0800h. This prevents the stack from For table operations, the 8-bit Table Memory Page interfering with the Special Function Register (SFR) Address register (TBLPAG) is used to define a 32Kword space. region within the program space. This is concatenated with a 16-bit EA to arrive at a full 24-bit program space Note: A write to the SPLIM register should not address. In this format, the Most Significant bit (MSb) of be immediately followed by an indirect TBLPAG is used to determine if the operation occurs in read operation using W15. the user memory (TBLPAG<7> = 0) or the configuration memory (TBLPAG<7> = 1). FIGURE 4-4: CALL STACK FRAME For remapping operations, the 8-bit Program Space 0000h 15 0 Visibility Page Address register (PSVPAG) is used to define a 16Kword page in the program space. When the MSb of the EA is ‘1’, PSVPAG is concatenated with the lower 15 bits of the EA to form a 23-bit program s ardss space address. Unlike the table operations, this limits we ows Toer Addr PC<15:0> W15 (before CALL) rTeamblaep4p-i2n7g aonpde rFaitgiounres 4st-r5ic stlhyo two thhoew u tsheer pmroegmroarmy EarAe ais. Grgh 000000000 PC<22:16> created for table operations and remapping accesses ck Hi <Free Word> W15 (after CALL) from the data EA. Here, the P<23:0> bits refer to a pro- a St gram space word, whereas the D<15:0> bits refer to a POP : [--W15] data space word. PUSH: [W15++] DS30009995E-page 51  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY TABLE 4-27: PROGRAM SPACE ADDRESS CONSTRUCTION Access Program Space Address Access Type Space <23> <22:16> <15> <14:1> <0> Instruction Access User 0 PC<22:1> 0 (Code Execution) 0xx xxxx xxxx xxxx xxxx xxx0 TBLRD/TBLWT User TBLPAG<7:0> Data EA<15:0> (Byte/Word Read/Write) 0xxx xxxx xxxx xxxx xxxx xxxx Configuration TBLPAG<7:0> Data EA<15:0> 1xxx xxxx xxxx xxxx xxxx xxxx Program Space Visibility User 0 PSVPAG<7:0>(2) Data EA<14:0>(1) (Block Remap/Read) 0 xxxx xxxx xxx xxxx xxxx xxxx Note 1: Data EA<15> is always ‘1’ in this case, but is not used in calculating the program space address. Bit 15 of the address is PSVPAG<0>. 2: PSVPAG can have only two values (‘00’ to access program memory and FF to access data EEPROM) in the PIC24FV32KA304 family. FIGURE 4-5: DATA ACCESS FROM PROGRAM SPACE ADDRESS GENERATION Program Counter(1) 0 Program Counter 0 23 Bits EA 1/0 Table Operations(2) 1/0 TBLPAG 8 Bits 16 Bits 24 Bits Select 1 EA 0 Program Space Visibility(1) 0 PSVPAG (Remapping) 8 Bits 15 Bits 23 Bits User/Configuration Byte Select Space Select Note 1: The LSb of program space addresses is always fixed as ‘0’ in order to maintain word alignment of data in the program and data spaces. 2: Table operations are not required to be word-aligned. Table Read operations are permitted in the configuration memory space.  2011-2017 Microchip Technology Inc. DS30009995E-page 52

PIC24FV32KA304 FAMILY 4.3.2 DATA ACCESS FROM PROGRAM Two table instructions are provided to move byte or MEMORY AND DATA EEPROM word-sized (16-bit) data to and from program space. MEMORY USING TABLE Both function as either byte or word operations. INSTRUCTIONS 1. TBLRDL (Table Read Low): In Word mode, it maps the lower word of the program space The TBLRDL and TBLWTL instructions offer a direct location (P<15:0>) to a data address (D<15:0>). method of reading or writing the lower word of any address within the program memory without going In Byte mode, either the upper or lower byte of through data space. It also offers a direct method of the lower program word is mapped to the lower reading or writing a word of any address within data byte of a data address. The upper byte is EEPROM memory. The TBLRDH and TBLWTH selected when byte select is ‘1’; the lower byte instructions are the only method to read or write the is selected when it is ‘0’. upper 8 bits of a program space word as data. 2. TBLRDH (Table Read High): In Word mode, it maps the entire upper word of a program address Note: The TBLRDH and TBLWTH instructions are (P<23:16>) to a data address. Note that not used while accessing data EEPROM D<15:8>, the ‘phantom’ byte, will always be ‘0’. memory. In Byte mode, it maps the upper or lower byte of The PC is incremented by two for each successive the program word to D<7:0> of the data 24-bit program word. This allows program memory address, as above. Note that the data will addresses to directly map to data space addresses. always be ‘0’ when the upper ‘phantom’ byte is Program memory can thus be regarded as two 16-bit selected (Byte Select = 1). word-wide address spaces, residing side by side, each with the same address range. TBLRDL and TBLWTL access the space which contains the least significant data word, and TBLRDH and TBLWTH access the space which contains the upper data byte. DS30009995E-page 53  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY In a similar fashion, two table instructions, TBLWTH TBLPAG<7> = 0, the table page is located in the user and TBLWTL, are used to write individual bytes or memory space. When TBLPAG<7> = 1, the page is words to a program space address. The details of located in configuration space. their operation are explained in Section5.0 “Flash Note: Only Table Read operations will execute Program Memory”. in the configuration memory space, and For all table operations, the area of program memory only then, in implemented areas, such as space to be accessed is determined by the Table the Device ID. Table Write operations are Memory Page Address register (TBLPAG). TBLPAG not allowed. covers the entire program memory space of the device, including user and configuration spaces. When FIGURE 4-6: ACCESSING PROGRAM MEMORY WITH TABLE INSTRUCTIONS Program Space Data EA<15:0> TBLPAG 00 23 16 8 0 00000000 23 15 0 000000h 00000000 00000000 002BFEh 00000000 ‘Phantom’ Byte TBLRDH.B (Wn<0> = 0) TBLRDL.B (Wn<0> = 1) TBLRDL.B (Wn<0> = 0) TBLRDL.W The address for the table operation is determined by the data EA within the page defined by the TBLPAG register. Only read 800000h operations are provided; write operations are also valid in the user memory area.  2011-2017 Microchip Technology Inc. DS30009995E-page 54

PIC24FV32KA304 FAMILY 4.3.3 READING DATA FROM PROGRAM Although each data space address, 8000h and higher, MEMORY USING PROGRAM SPACE maps directly into a corresponding program memory VISIBILITY address (see Figure4-7), only the lower 16 bits of the 24-bit program word are used to contain the data. The The upper 32 Kbytes of data space may optionally be upper 8 bits of any program space location used as data mapped into a 16K word page (in PIC24FV16KA3XX should be programmed with ‘1111 1111’ or ‘0000 devices) and a 32K word page (in PIC24FV32KA3XX 0000’ to force a NOP. This prevents possible issues devices) of the program space. This provides should the area of code ever be accidentally executed. transparent access of stored constant data from the data space without the need to use special instructions Note: PSV access is temporarily disabled during (i.e., TBLRDL/H). Table Reads/Writes. Program space access through the data space occurs For operations that use PSV and are executed outside a if the MSb of the data space EA is ‘1’ and PSV is REPEAT loop, the MOV and MOV.D instructions will require enabled by setting the PSV bit in the CPU Control one instruction cycle in addition to the specified execution (CORCON<2>) register. The location of the program time. All other instructions will require two instruction memory space to be mapped into the data space is cycles in addition to the specified execution time. determined by the Program Space Visibility Page For operations that use PSV, which are executed inside Address (PSVPAG) register. This 8-bit register defines a REPEAT loop, there will be some instances that any one of 256 possible pages of 16K words in program require two instruction cycles in addition to the space. In effect, PSVPAG functions as the upper 8 bits specified execution time of the instruction: of the program memory address, with the 15 bits of the EA functioning as the lower bits. • Execution in the first iteration • Execution in the last iteration By incrementing the PC by 2 for each program memory word, the lower 15 bits of data space addresses directly • Execution prior to exiting the loop due to an map to the lower 15 bits in the corresponding program interrupt space addresses. • Execution upon re-entering the loop after an interrupt is serviced Data reads from this area add an additional cycle to the instruction being executed, since two program memory Any other iteration of the REPEAT loop will allow the fetches are required. instruction accessing data, using PSV, to execute in a single cycle. FIGURE 4-7: PROGRAM SPACE VISIBILITY OPERATION When CORCON<2> = 1 and EA<15> = 1: Program Space Data Space PSVPAG 23 15 0 00 000000h 0000h Data EA<14:0> 002BFEh The data in the page designated by PSVPAG is mapped into the upper half of the data memory 8000h space.... PSV Area ...while the lower 15 bits of the EA specify an exact address within the PSV FFFFh area. This corresponds exactly to the same lower 15 bits of the actual program space address. 800000h  2011-2017 Microchip Technology Inc. DS30009995E-page 55

PIC24FV32KA304 FAMILY NOTES: DS30009995E-page 56  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 5.0 FLASH PROGRAM MEMORY Run-Time Self Programming (RTSP) is accomplished using TBLRD (Table Read) and TBLWT (Table Write) Note: This data sheet summarizes the features of instructions. With RTSP, the user may write program this group of PIC24F devices. It is not memory data in blocks of 32 instructions (96 bytes) at intended to be a comprehensive reference a time, and erase program memory in blocks of 32, 64 source. For more information on Flash and 128 instructions (96,192 and 384 bytes) at a time. programming, refer to the “dsPIC33/PIC24 The NVMOP<1:0> (NVMCON<1:0>) bits decide the Family Reference Manual”, “PIC24F erase block size. Flash Program Memory” (DS30009715). 5.1 Table Instructions and Flash The PIC24FV32KA304 family of devices contains internal Flash program memory for storing and executing Programming application code. The memory is readable, writable and Regardless of the method used, Flash memory erasable when operating with VDD over 1.8V. programming is done with the Table Read and Write Flash memory can be programmed in three ways: instructions. These allow direct read and write access to • In-Circuit Serial Programming™ (ICSP™) the program memory space from the data memory while • Run-Time Self Programming (RTSP) the device is in normal operating mode. The 24-bit target address in the program memory is formed using the • Enhanced In-Circuit Serial Programming TBLPAG<7:0> bits and the Effective Address (EA) from (Enhanced ICSP) a W register, specified in the table instruction, as ICSP allows a PIC24FV32KA304 device to be serially depicted in Figure5-1. programmed while in the end application circuit. This is The TBLRDL and the TBLWTL instructions are used to simply done with two lines for the programming clock read or write to bits<15:0> of program memory. and programming data (which are named PGECx and TBLRDL and TBLWTL can access program memory in PGEDx, respectively), and three other lines for power both Word and Byte modes. (VDD), ground (VSS) and Master Clear/Program mode Entry Voltage (MCLR/VPP). This allows customers to The TBLRDH and TBLWTH instructions are used to read manufacture boards with unprogrammed devices and or write to bits<23:16> of program memory. TBLRDH then program the microcontroller just before shipping and TBLWTH can also access program memory in Word the product. This also allows the most recent firmware or Byte mode. or custom firmware to be programmed. FIGURE 5-1: ADDRESSING FOR TABLE REGISTERS 24 Bits Using Program 0 Program Counter 0 Counter Working Reg EA Using 1/0 TBLPAG Reg Table Instruction 8 Bits 16 Bits User/Configuration Byte Space Select 24-Bit EA Select  2011-2017 Microchip Technology Inc. DS30009995E-page 57

PIC24FV32KA304 FAMILY 5.2 RTSP Operation 5.3 Enhanced In-Circuit Serial Programming The PIC24F Flash program memory array is organized into rows of 32 instructions or 96 bytes. RTSP allows Enhanced ICSP uses an on-board bootloader, known as the user to erase blocks of 1 row, 2 rows and 4 rows the Programming Executive (PE), to manage the pro- (32,64 and 128 instructions) at a time, and to program gramming process. Using an SPI data frame format, the one row at a time. It is also possible to program single Programming Executive can erase, program and verify words. program memory. For more information on Enhanced The 1-row (96 bytes), 2-row (192 bytes) and 4-row ICSP, see the device programming specification. (384 bytes) erase blocks, and single row write block (96 bytes) are edge-aligned from the beginning of 5.4 Control Registers program memory. There are two SFRs used to read and write the When data is written to program memory using TBLWT program Flash memory: NVMCON and NVMKEY. instructions, the data is not written directly to memory. The NVMCON register (Register5-1) controls the blocks Instead, data written using Table Writes is stored in holding that need to be erased, which memory type is to be latches until the programming sequence is executed. programmed and when the programming cycle starts. Any number of TBLWT instructions can be executed NVMKEY is a write-only register that is used for write and a write will be successfully performed. However, protection. To start a programming or erase sequence, 32TBLWT instructions are required to write the full row the user must consecutively write 55h and AAh to the of memory. NVMKEY register. For more information, refer to The basic sequence for RTSP programming is to set up Section5.5 “Programming Operations”. a Table Pointer, then do a series of TBLWT instructions to load the buffers. Programming is performed by setting 5.5 Programming Operations the control bits in the NVMCON register. A complete programming sequence is necessary for Data can be loaded in any order and the holding registers programming or erasing the internal Flash in RTSP can be written to multiple times before performing a write mode. During a program or erase operation, the operation. Subsequent writes, however, will wipe out any processor stalls (Waits) until the operation is finished. previous writes. Setting the WR bit (NVMCON<15>) starts the opera- Note: Writing to a location multiple times without tion and the WR bit is automatically cleared when the erasing it is not recommended. operation is finished. All of the Table Write operations are single-word writes (two instruction cycles), because only the buffers are written. A programming cycle is required for programming each row. DS30009995E-page 58  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 5-1: NVMCON: FLASH MEMORY CONTROL REGISTER R/SO-0, HC R/W-0 R/W-0 R/W-0 U-0 U-0 U-0 U-0 WR WREN WRERR PGMONLY(4) — — — — bit 15 bit 8 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — ERASE NVMOP5(1) NVMOP4(1) NVMOP3(1) NVMOP2(1) NVMOP1(1) NVMOP0(1) bit 7 bit 0 Legend: SO = Settable Only bit HC = Hardware Clearable bit -n = Value at POR ‘1’ = Bit is set R = Readable bit W = Writable bit ‘0’ = Bit is cleared x = Bit is unknown U = Unimplemented bit, read as ‘0’ bit 15 WR: Write Control bit 1 = Initiates a Flash memory program or erase operation. The operation is self-timed and the bit is cleared by hardware once the operation is complete. 0 = Program or erase operation is complete and inactive bit 14 WREN: Write Enable bit 1 = Enables Flash program/erase operations 0 = Inhibits Flash program/erase operations bit 13 WRERR: Write Sequence Error Flag bit 1 = An improper program or erase sequence attempt, or termination, has occurred (bit is set automatically on any set attempt of the WR bit) 0 = The program or erase operation completed normally bit 12 PGMONLY: Program Only Enable bit(4) bit 11-7 Unimplemented: Read as ‘0’ bit 6 ERASE: Erase/Program Enable bit 1 = Performs the erase operation specified by NVMOP<5:0> on the next WR command 0 = Performs the program operation specified by NVMOP<5:0> on the next WR command bit 5-0 NVMOP<5:0>: Programming Operation Command Byte bits(1) Erase Operations (when ERASE bit is ‘1’): 1010xx = Erases entire boot block (including code-protected boot block)(2) 1001xx = Erases entire memory (including boot block, configuration block, general block)(2) 011010 = Erases 4 rows of Flash memory(3) 011001 = Erases 2 rows of Flash memory(3) 011000 = Erases 1 row of Flash memory(3) 0101xx = Erases entire configuration block (except code protection bits) 0100xx = Erases entire data EEPROM(4) 0011xx = Erases entire general memory block programming operations 0001xx = Writes 1 row of Flash memory (when ERASE bit is ‘0’)(3) Note 1: All other combinations of NVMOP<5:0> are no operation. 2: These values are available in ICSP™ mode only. Refer to the device programming specification. 3: The address in the Table Pointer decides which rows will be erased. 4: This bit is used only while accessing data EEPROM.  2011-2017 Microchip Technology Inc. DS30009995E-page 59

PIC24FV32KA304 FAMILY 5.5.1 PROGRAMMING ALGORITHM FOR 4. Write the first 32 instructions from data RAM into FLASH PROGRAM MEMORY the program memory buffers (see Example5-1). 5. Write the program block to Flash memory: The user can program one row of Flash program memory at a time by erasing the programmable row. a) Set the NVMOPx bits to ‘011000’ to The general process is as follows: configure for row programming. Clear the ERASE bit and set the WREN bit. 1. Read a row of program memory (32instructions) b) Write 55h to NVMKEY. and store in data RAM. c) Write AAh to NVMKEY. 2. Update the program data in RAM with the desired new data. d) Set the WR bit. The programming cycle begins and the CPU stalls for the duration of 3. Erase a row (see Example5-1): the write cycle. When the write to Flash a) Set the NVMOPx bits (NVMCON<5:0>) to memory is done, the WR bit is cleared ‘011000’ to configure for row erase. Set the automatically. ERASE (NVMCON<6>) and WREN (NVMCON<14>) bits. For protection against accidental operations, the write initiate sequence for NVMKEY must be used to allow b) Write the starting address of the block to be any erase or program operation to proceed. After the erased into the TBLPAG and W registers. programming command has been executed, the user c) Write 55h to NVMKEY. must wait for the programming time until programming d) Write AAh to NVMKEY. is complete. The two instructions following the start of e) Set the WR bit (NVMCON<15>). The erase the programming sequence should be NOPs, as shown cycle begins and the CPU stalls for the in Example5-5. duration of the erase cycle. When the erase is done, the WR bit is cleared automatically. EXAMPLE 5-1: ERASING A PROGRAM MEMORY ROW – ASSEMBLY LANGUAGE CODE ; Set up NVMCON for row erase operation MOV #0x4058, W0 ; MOV W0, NVMCON ; Initialize NVMCON ; Init pointer to row to be ERASED MOV #tblpage(PROG_ADDR), W0 ; MOV W0, TBLPAG ; Initialize PM Page Boundary SFR MOV #tbloffset(PROG_ADDR), W0 ; Initialize in-page EA[15:0] pointer TBLWTL W0, [W0] ; Set base address of erase block DISI #5 ; Block all interrupts for next 5 instructions MOV #0x55, W0 MOV W0, NVMKEY ; Write the 55 key MOV #0xAA, W1 ; MOV W1, NVMKEY ; Write the AA key BSET NVMCON, #WR ; Start the erase sequence NOP ; Insert two NOPs after the erase NOP ; command is asserted DS30009995E-page 60  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY EXAMPLE 5-2: ERASING A PROGRAM MEMORY ROW – ‘C’ LANGUAGE CODE // C example using MPLAB C30 int __attribute__ ((space(auto_psv))) progAddr = 0x1234;// Global variable located in Pgm Memory unsigned int offset; //Set up pointer to the first memory location to be written TBLPAG = __builtin_tblpage(&progAddr); // Initialize PM Page Boundary SFR offset = __builtin_tbloffset(&progAddr); // Initialize lower word of address __builtin_tblwtl(offset, 0x0000); // Set base address of erase block // with dummy latch write NVMCON = 0x4058; // Initialize NVMCON asm("DISI #5"); // Block all interrupts for next 5 // instructions __builtin_write_NVM(); // C30 function to perform unlock // sequence and set WR EXAMPLE 5-3: LOADING THE WRITE BUFFERS – ASSEMBLY LANGUAGE CODE ; Set up NVMCON for row programming operations MOV #0x4004, W0 ; MOV W0, NVMCON ; Initialize NVMCON ; Set up a pointer to the first program memory location to be written ; program memory selected, and writes enabled MOV #0x0000, W0 ; MOV W0, TBLPAG ; Initialize PM Page Boundary SFR MOV #0x6000, W0 ; An example program memory address ; Perform the TBLWT instructions to write the latches ; 0th_program_word MOV #LOW_WORD_0, W2 ; MOV #HIGH_BYTE_0, W3 ; TBLWTL W2, [W0] ; Write PM low word into program latch TBLWTH W3, [W0++] ; Write PM high byte into program latch ; 1st_program_word MOV #LOW_WORD_1, W2 ; MOV #HIGH_BYTE_1, W3 ; TBLWTL W2, [W0] ; Write PM low word into program latch TBLWTH W3, [W0++] ; Write PM high byte into program latch ; 2nd_program_word MOV #LOW_WORD_2, W2 ; MOV #HIGH_BYTE_2, W3 ; TBLWTL W2, [W0] ; Write PM low word into program latch TBLWTH W3, [W0++] ; Write PM high byte into program latch • • • ; 32nd_program_word MOV #LOW_WORD_31, W2 ; MOV #HIGH_BYTE_31, W3 ; TBLWTL W2, [W0] ; Write PM low word into program latch TBLWTH W3, [W0] ; Write PM high byte into program latch  2011-2017 Microchip Technology Inc. DS30009995E-page 61

PIC24FV32KA304 FAMILY EXAMPLE 5-4: LOADING THE WRITE BUFFERS – ‘C’ LANGUAGE CODE // C example using MPLAB C30 #define NUM_INSTRUCTION_PER_ROW 64 int __attribute__ ((space(auto_psv))) progAddr = 0x1234; // Global variable located in Pgm Memory unsigned int offset; unsigned int i; unsigned int progData[2*NUM_INSTRUCTION_PER_ROW]; // Buffer of data to write //Set up NVMCON for row programming NVMCON = 0x4001; // Initialize NVMCON //Set up pointer to the first memory location to be written TBLPAG = __builtin_tblpage(&progAddr); // Initialize PM Page Boundary SFR offset = __builtin_tbloffset(&progAddr); // Initialize lower word of address //Perform TBLWT instructions to write necessary number of latches for(i=0; i < 2*NUM_INSTRUCTION_PER_ROW; i++) { __builtin_tblwtl(offset, progData[i++]); // Write to address low word __builtin_tblwth(offset, progData[i]); // Write to upper byte offset = offset + 2; // Increment address } EXAMPLE 5-5: INITIATING A PROGRAMMING SEQUENCE – ASSEMBLY LANGUAGE CODE DISI #5 ; Block all interrupts for next 5 instructions MOV #0x55, W0 MOV W0, NVMKEY ; Write the 55 key MOV #0xAA, W1 ; MOV W1, NVMKEY ; Write the AA key BSET NVMCON, #WR ; Start the erase sequence NOP ; 2 NOPs required after setting WR NOP ; BTSC NVMCON, #15 ; Wait for the sequence to be completed BRA $-2 ; EXAMPLE 5-6: INITIATING A PROGRAMMING SEQUENCE – ‘C’ LANGUAGE CODE // C example using MPLAB C30 asm("DISI #5"); // Block all interrupts for next 5 instructions __builtin_write_NVM(); // Perform unlock sequence and set WR DS30009995E-page 62  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 6.0 DATA EEPROM MEMORY 6.1 NVMCON Register Note: This data sheet summarizes the features The NVMCON register (Register6-1) is also the primary of this group of PIC24F devices. It is not control register for data EEPROM program/erase intended to be a comprehensive reference operations. The upper byte contains the control bits source. For more information on Data used to start the program or erase cycle, and the flag bit EEPROM, refer to the “dsPIC33/PIC24 to indicate if the operation was successfully performed. Family Reference Manual”, “Data The lower byte of NVMCOM configures the type of NVM EEPROM” (DS39720). operation that will be performed. The data EEPROM memory is a Nonvolatile Memory 6.2 NVMKEY Register (NVM), separate from the program and volatile data RAM. Data EEPROM memory is based on the same The NVMKEY is a write-only register that is used to Flash technology as program memory, and is optimized prevent accidental writes or erasures of data EEPROM for both long retention and a higher number of locations. erase/write cycles. To start any programming or erase sequence, the The data EEPROM is mapped to the top of the user following instructions must be executed first, in the program memory space, with the top address at pro- exact order provided: gram memory address, 7FFE00h to 7FFFFFh. The 1. Write 55h to NVMKEY. size of the data EEPROM is 256 words in the 2. Write AAh to NVMKEY. PIC24FV32KA304 family devices. After this sequence, a write will be allowed to the The data EEPROM is organized as 16-bit wide NVMCON register for one instruction cycle. In most memory. Each word is directly addressable, and is cases, the user will simply need to set the WR bit in the readable and writable during normal operation over the NVMCON register to start the program or erase cycle. entire VDD range. Interrupts should be disabled during the unlock Unlike the Flash program memory, normal program sequence. execution is not stopped during a data EEPROM The MPLAB® C30 C compiler provides a defined library program or erase operation. procedure (builtin_write_NVM) to perform the The data EEPROM programming operations are unlock sequence. Example6-1illustrates how the controlled using the three NVM Control registers: unlock sequence can be performed with in-line assembly. • NVMCON: Nonvolatile Memory Control Register • NVMKEY: Nonvolatile Memory Key Register • NVMADR: Nonvolatile Memory Address Register EXAMPLE 6-1: DATA EEPROM UNLOCK SEQUENCE //Disable Interrupts For 5 instructions asm volatile ("disi #5"); //Issue Unlock Sequence asm volatile ("mov #0x55, W0 \n" "mov W0, NVMKEY \n" "mov #0xAA, W1 \n" "mov W1, NVMKEY \n"); // Perform Write/Erase operations asm volatile ("bset NVMCON, #WR \n" "nop \n" "nop \n");  2011-2017 Microchip Technology Inc. DS30009995E-page 63

PIC24FV32KA304 FAMILY REGISTER 6-1: NVMCON: NONVOLATILE MEMORY CONTROL REGISTER R/S-0, HC R/W-0 R/W-0 R/W-0 U-0 U-0 U-0 U-0 WR WREN WRERR PGMONLY — — — — bit 15 bit 8 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — ERASE NVMOP5 NVMOP4 NVMOP3 NVMOP2 NVMOP1 NVMOP0 bit 7 bit 0 Legend: HC = Hardware Clearable bit U = Unimplemented bit, read as ‘0’ R = Readable bit W = Writable bit S = Settable bit -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 WR: Write Control bit (program or erase) 1 = Initiates a data EEPROM erase or write cycle (can be set, but not cleared in software) 0 = Write cycle is complete (cleared automatically by hardware) bit 14 WREN: Write Enable bit (erase or program) 1 = Enables an erase or program operation 0 = No operation allowed (device clears this bit on completion of the write/erase operation) bit 13 WRERR: Write Flash Error Flag bit 1 = A write operation is prematurely terminated (any MCLR or WDT Reset during programming operation) 0 = The write operation completed successfully bit 12 PGMONLY: Program Only Enable bit 1 = Write operation is executed without erasing target address(es) first 0 = Automatic erase-before-write Write operations are preceded automatically by an erase of the target address(es). bit 11-7 Unimplemented: Read as ‘0’ bit 6 ERASE: Erase Operation Select bit 1 = Performs an erase operation when WR is set 0 = Performs a write operation when WR is set bit 5-0 NVMOP<5:0>: Programming Operation Command Byte bits Erase Operations (when ERASE bit is ‘1’): 011010 = Erases 8 words 011001 = Erases 4 words 011000 = Erases 1 word 0100xx = Erases entire data EEPROM Programming Operations (when ERASE bit is ‘0’): 0001xx = Writes 1 word DS30009995E-page 64  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 6.3 NVM Address Register 6.4 Data EEPROM Operations As with Flash program memory, the NVM Address The EEPROM block is accessed using Table Read and registers, NVMADRU and NVMADR, form the 24-bit Write operations similar to those used for program Effective Address (EA) of the selected row or word for memory. The TBLWTH and TBLRDH instructions are not data EEPROM operations. The NVMADRU register is required for data EEPROM operations since the used to hold the upper 8 bits of the EA, while the memory is only 16 bits wide (data on the lower address NVMADR register is used to hold the lower 16 bits of is valid only). The following programming operations the EA. These registers are not mapped into the can be performed on the data EEPROM: Special Function Register (SFR) space. Instead, they • Erase one, four or eight words directly capture the EA<23:0> of the last Table Write • Bulk erase the entire data EEPROM instruction that has been executed and selects the data • Write one word EEPROM row to erase. Figure6-1 depicts the program memory EA that is formed for programming and erase • Read one word operations. Note1: Unexpected results will be obtained if the Like program memory operations, the Least Significant user attempts to read the EEPROM while bit (LSb) of NVMADR is restricted to even addresses. a programming or erase operation is This is because any given address in the data EEPROM underway. space consists of only the lower word of the program 2: The C30 C compiler includes library pro- memory width; the upper word, including the uppermost cedures to automatically perform the “phantom byte”, are unavailable. This means that the Table Read and Table Write operations, LSb of a data EEPROM address will always be ‘0’. manage the Table Pointer and write buf- Similarly, the Most Significant bit (MSb) of NVMADRU fers, and unlock and initiate memory is always ‘0’, since all addresses lie in the user program write sequences. This eliminates the space. need to create assembler macros or time critical routines in C for each application. FIGURE 6-1: DATA EEPROM ADDRESSING WITH The library procedures are used in the code examples TBLPAG AND NVM detailed in the following sections. General descriptions ADDRESS REGISTERS of each process are provided for users who are not using the C30 compiler libraries. 24-Bit PM Address 7Fh xxxxh 0 TBLPAG W Register EA 0 NVMADRU NVMADR  2011-2017 Microchip Technology Inc. DS30009995E-page 65

PIC24FV32KA304 FAMILY 6.4.1 ERASE DATA EEPROM A typical erase sequence is provided in Example6-2. This example shows how to do a one-word erase. The data EEPROM can be fully erased, or can be Similarly, a four-word erase and an eight-word erase partially erased, at three different sizes: one word, four can be done. This example uses C library procedures to words or eight words. The bits, NVMOP<1:0> manage the Table Pointer (builtin_tblpage and (NVMCON<1:0>), decide the number of words to be builtin_tbloffset) and the Erase Page Pointer erased. To erase partially from the data EEPROM, the (builtin_tblwtl). The memory unlock sequence following sequence must be followed: (builtin_write_NVM) also sets the WR bit to initiate 1. Configure NVMCON to erase the required the operation and returns control when complete. number of words: one, four or eight. 2. Load TBLPAG and WREG with the EEPROM address to be erased. 3. Clear the NVMIF status bit and enable the NVM interrupt (optional). 4. Write the key sequence to NVMKEY. 5. Set the WR bit to begin the erase cycle. 6. Either poll the WR bit or wait for the NVM interrupt (NVMIF is set). EXAMPLE 6-2: SINGLE-WORD ERASE int __attribute__ ((space(eedata))) eeData = 0x1234; /*-------------------------------------------------------------------------------------------- The variable eeData must be a Global variable declared outside of any method the code following this comment can be written inside the method that will execute the erase ---------------------------------------------------------------------------------------------- */ unsigned int offset; // Set up NVMCON to erase one word of data EEPROM NVMCON = 0x4058; // Set up a pointer to the EEPROM location to be erased TBLPAG = __builtin_tblpage(&eeData); // Initialize EE Data page pointer offset = __builtin_tbloffset(&eeData); // Initizlize lower word of address __builtin_tblwtl(offset, 0); // Write EEPROM data to write latch asm volatile ("disi #5"); // Disable Interrupts For 5 Instructions __builtin_write_NVM(); // Issue Unlock Sequence & Start Write Cycle while(NVMCONbits.WR=1); // Optional: Poll WR bit to wait for // write sequence to complete DS30009995E-page 66  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 6.4.1.1 Data EEPROM Bulk Erase 6.4.2 SINGLE-WORD WRITE To erase the entire data EEPROM (bulk erase), the To write a single word in the data EEPROM, the address registers do not need to be configured following sequence must be followed: because this operation affects the entire data 1. Erase one data EEPROM word (as mentioned in EEPROM. The following sequence helps in performing the previous section) if the PGMONLY bit a bulk erase: (NVMCON<12>) is set to ‘1’. 1. Configure NVMCON to Bulk Erase mode. 2. Write the data word into the data EEPROM 2. Clear the NVMIF status bit and enable the NVM latch. interrupt (optional). 3. Program the data word into the EEPROM: 3. Write the key sequence to NVMKEY. - Configure the NVMCON register to 4. Set the WR bit to begin the erase cycle. program one EEPROM word 5. Either poll the WR bit or wait for the NVM (NVMCON<5:0> = 0001xx). interrupt (NVMIF is set). - Clear the NVMIF status bit and enable the NVM interrupt (optional). A typical bulk erase sequence is provided in Example6-3. - Write the key sequence to NVMKEY. - Set the WR bit to begin the erase cycle. - Either poll the WR bit or wait for the NVM interrupt (NVMIF is set). - To get cleared, wait until NVMIF is set. A typical single-word write sequence is provided in Example6-4. EXAMPLE 6-3: DATA EEPROM BULK ERASE // Set up NVMCON to bulk erase the data EEPROM NVMCON = 0x4050; // Disable Interrupts For 5 Instructions asm volatile ("disi #5"); // Issue Unlock Sequence and Start Erase Cycle __builtin_write_NVM(); EXAMPLE 6-4: SINGLE-WORD WRITE TO DATA EEPROM int __attribute__ ((space(eedata))) eeData = 0x1234; int newData; // New data to write to EEPROM /*--------------------------------------------------------------------------------------------- The variable eeData must be a Global variable declared outside of any method the code following this comment can be written inside the method that will execute the write ----------------------------------------------------------------------------------------------- */ unsigned int offset; // Set up NVMCON to erase one word of data EEPROM NVMCON = 0x4004; // Set up a pointer to the EEPROM location to be erased TBLPAG = __builtin_tblpage(&eeData); // Initialize EE Data page pointer offset = __builtin_tbloffset(&eeData); // Initizlize lower word of address __builtin_tblwtl(offset, newData); // Write EEPROM data to write latch asm volatile ("disi #5"); // Disable Interrupts For 5 Instructions __builtin_write_NVM(); // Issue Unlock Sequence & Start Write Cycle while(NVMCONbits.WR=1); // Optional: Poll WR bit to wait for // write sequence to complete  2011-2017 Microchip Technology Inc. DS30009995E-page 67

PIC24FV32KA304 FAMILY 6.4.3 READING THE DATA EEPROM A typical read sequence, using the Table Pointer management (builtin_tblpage and To read a word from data EEPROM, the Table Read builtin_tbloffset) and Table Read procedures instruction is used. Since the EEPROM array is only (builtin_tblrdl) from the C30 compiler library, is 16bits wide, only the TBLRDL instruction is needed. provided in Example6-5. The read operation is performed by loading TBLPAG and WREG with the address of the EEPROM location, Program Space Visibility (PSV) can also be used to followed by a TBLRDL instruction. read locations in the data EEPROM. EXAMPLE 6-5: READING THE DATA EEPROM USING THE TBLRD COMMAND int __attribute__ ((space(eedata))) eeData = 0x1234; int data; // Data read from EEPROM /*-------------------------------------------------------------------------------------------- The variable eeData must be a Global variable declared outside of any method the code following this comment can be written inside the method that will execute the read ---------------------------------------------------------------------------------------------- */ unsigned int offset; // Set up a pointer to the EEPROM location to be erased TBLPAG = __builtin_tblpage(&eeData); // Initialize EE Data page pointer offset = __builtin_tbloffset(&eeData); // Initizlize lower word of address data = __builtin_tblrdl(offset); // Write EEPROM data to write latch DS30009995E-page 68  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 7.0 RESETS Any active source of Reset will make the SYSRST signal active. Many registers associated with the CPU Note: This data sheet summarizes the features and peripherals are forced to a known Reset state. of this group of PIC24F devices. It is not Most registers are unaffected by a Reset; their status is intended to be a comprehensive refer- unknown on Power-on Reset (POR) and unchanged by ence source. For more information on all other Resets. Resets, refer to the “dsPIC33/PIC24 Note: Refer to the specific peripheral or Family Reference Manual”, “Reset with Section3.0 “CPU” of this data sheet for Programmable Brown-out Reset” register Reset states. (DS39728). The Reset module combines all Reset sources and All types of device Reset will set a corresponding status controls the device Master Reset Signal, SYSRST. The bit in the RCON register to indicate the type of Reset following is a list of device Reset sources: (see Register7-1). A Power-on Reset will clear all bits except for the BOR and POR bits (RCON<1:0>) which • POR: Power-on Reset are set. The user may set or clear any bit at any time • MCLR: Pin Reset during code execution. The RCON bits only serve as • SWR: RESET Instruction status bits. Setting a particular Reset status bit in • WDTR: Watchdog Timer Reset software will not cause a device Reset to occur. • BOR: Brown-out Reset The RCON register also has other bits associated with • Low-Power BOR/Deep Sleep BOR the Watchdog Timer (WDT) and device power-saving states. The function of these bits is discussed in other • TRAPR: Trap Conflict Reset sections of this manual. • IOPUWR: Illegal Opcode Reset • UWR: Uninitialized W Register Reset Note: The status bits in the RCON register should be cleared after they are read so A simplified block diagram of the Reset module is that the next RCON register value after a shown in Figure7-1. device Reset will be meaningful. FIGURE 7-1: RESET SYSTEM BLOCK DIAGRAM RESET Instruction Glitch Filter MCLR WDT Module Sleep or Idle VDD Rise POR Detect SYSRST BOREN<1:0> VDD 0 00 Brown-out BOR SBOREN Reset 01 (RCON<13>) SLEEP 10 Enable Voltage Regulator 1 11 (PIC24FV32KA3XX only) Configuration Mismatch Trap Conflict Illegal Opcode Uninitialized W Register  2011-2017 Microchip Technology Inc. DS30009995E-page 69

PIC24FV32KA304 FAMILY REGISTER 7-1: RCON: RESET CONTROL REGISTER(1) R/W-0, HS R/W-0, HS R/W-0 R/W-0 U-0 R/C-0, HS R/W-0 R/W-0 TRAPR IOPUWR SBOREN RETEN(3) — DPSLP CM PMSLP bit 15 bit 8 R/W-0, HS R/W-0, HS R/W-0, HS R/W-0, HS R/W-0, HS R/W-0, HS R/W-1, HS R/W-1, HS EXTR SWR SWDTEN(2) WDTO SLEEP IDLE BOR POR bit 7 bit 0 Legend: C = Clearable bit HS = Hardware Settable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 TRAPR: Trap Reset Flag bit 1 = A Trap Conflict Reset has occurred 0 = A Trap Conflict Reset has not occurred bit 14 IOPUWR: Illegal Opcode or Uninitialized W Access Reset Flag bit 1 = An illegal opcode detection, an illegal address mode or Uninitialized W register used as an Address Pointer caused a Reset 0 = An illegal opcode or Uninitialized W Reset has not occurred bit 13 SBOREN: Software Enable/Disable of BOR bit 1 = BOR is turned on in software 0 = BOR is turned off in software bit 12 RETEN: Retention Sleep Mode control bit(3) 1 = Regulated voltage supply provided solely by the Retention Regulator (RETEN) during Sleep 0 = Regulated voltage supply provided by the main Voltage Regulator (VREG) during Sleep bit 11 Unimplemented: Read as ‘0’ bit 10 DPSLP: Deep Sleep Mode Flag bit 1 = Deep Sleep has occurred 0 = Deep Sleep has not occurred bit 9 CM: Configuration Word Mismatch Reset Flag bit 1 = A Configuration Word Mismatch Reset has occurred 0 = A Configuration Word Mismatch Reset has not occurred bit 8 PMSLP: Program Memory Power During Sleep bit 1 = Program memory bias voltage remains powered during Sleep 0 = Program memory bias voltage is powered down during Sleep and the Voltage Regulator enters Standby mode bit 7 EXTR: External Reset (MCLR) Pin bit 1 = A Master Clear (pin) Reset has occurred 0 = A Master Clear (pin) Reset has not occurred bit 6 SWR: Software Reset (Instruction) Flag bit 1 = A RESET instruction has been executed 0 = A RESET instruction has not been executed Note 1: All of the Reset status bits may be set or cleared in software. Setting one of these bits in software does not cause a device Reset. 2: If the FWDTENx Configuration bit is ‘1’ (unprogrammed), the WDT is always enabled regardless of the SWDTEN bit setting. 3: This is implemented on PIC24FV32KA3XX parts only; not used on PIC24F32KA3XX devices. DS30009995E-page 70  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 7-1: RCON: RESET CONTROL REGISTER(1) (CONTINUED) bit 5 SWDTEN: Software Enable/Disable of WDT bit(2) 1 = WDT is enabled 0 = WDT is disabled bit 4 WDTO: Watchdog Timer Time-out Flag bit 1 = WDT time-out has occurred 0 = WDT time-out has not occurred bit 3 SLEEP: Wake-up from Sleep Flag bit 1 = Device has been in Sleep mode 0 = Device has not been in Sleep mode bit 2 IDLE: Wake-up from Idle Flag bit 1 = Device has been in Idle mode 0 = Device has not been in Idle mode bit 1 BOR: Brown-out Reset Flag bit 1 = A Brown-out Reset has occurred (the BOR is also set after a POR) 0 = A Brown-out Reset has not occurred bit 0 POR: Power-on Reset Flag bit 1 = A Power-up Reset has occurred 0 = A Power-up Reset has not occurred Note 1: All of the Reset status bits may be set or cleared in software. Setting one of these bits in software does not cause a device Reset. 2: If the FWDTENx Configuration bit is ‘1’ (unprogrammed), the WDT is always enabled regardless of the SWDTEN bit setting. 3: This is implemented on PIC24FV32KA3XX parts only; not used on PIC24F32KA3XX devices. TABLE 7-1: RESET FLAG BIT OPERATION Flag Bit Setting Event Clearing Event TRAPR (RCON<15>) Trap Conflict Event POR IOPUWR (RCON<14>) Illegal Opcode or Uninitialized W Register Access POR CM (RCON<9>) Configuration Mismatch Reset POR EXTR (RCON<7>) MCLR Reset POR SWR (RCON<6>) RESET Instruction POR WDTO (RCON<4>) WDT Time-out PWRSAV Instruction, POR SLEEP (RCON<3>) PWRSAV #SLEEP Instruction POR IDLE (RCON<2>) PWRSAV #IDLE Instruction POR BOR (RCON<1>) POR, BOR — POR (RCON<0>) POR — DPSLP (RCON<10>) PWRSAV #SLEEP Instruction with DSEN (DSCON<15>) Set POR Note: All Reset flag bits may be set or cleared by the user software.  2011-2017 Microchip Technology Inc. DS30009995E-page 71

PIC24FV32KA304 FAMILY 7.1 Clock Source Selection at Reset 7.2 Device Reset Times If clock switching is enabled, the system clock source at The Reset times for various types of device Reset are device Reset is chosen, as shown in Table7-2. If clock summarized in Table7-3. Note that the System Reset switching is disabled, the system clock source is always Signal, SYSRST, is released after the POR and PWRT selected according to the Oscillator Configuration bits. delay times expire. For more information, see Section9.0 “Oscillator The time at which the device actually begins to execute Configuration”. code will also depend on the system oscillator delays, which include the Oscillator Start-up Timer (OST) and TABLE 7-2: OSCILLATOR SELECTION vs. the PLL lock time. The OST and PLL lock times occur TYPE OF RESET (CLOCK in parallel with the applicable SYSRST delay times. SWITCHING ENABLED) The FSCM delay determines the time at which the Reset Type Clock Source Determinant FSCM begins to monitor the system clock source after the SYSRST signal is released. POR FNOSCx Configuration bits BOR (FNOSC<10:8>) MCLR COSCx Control bits WDTO (OSCCON<14:12>) SWR TABLE 7-3: DELAY TIMES FOR VARIOUS DEVICE RESETS System Clock Reset Type Clock Source SYSRST Delay Notes Delay POR(6) EC TPOR + TPWRT — 1, 2 FRC, FRCDIV TPOR + TPWRT TFRC 1, 2, 3 LPRC TPOR + TPWRT TLPRC 1, 2, 3 ECPLL TPOR + TPWRT TLOCK 1, 2, 4 FRCPLL TPOR + TPWRT TFRC + TLOCK 1, 2, 3, 4 XT, HS, SOSC TPOR+ TPWRT TOST 1, 2, 5 XTPLL, HSPLL TPOR + TPWRT TOST + TLOCK 1, 2, 4, 5 BOR EC TPWRT — 2 FRC, FRCDIV TPWRT TFRC 2, 3 LPRC TPWRT TLPRC 2, 3 ECPLL TPWRT TLOCK 2, 4 FRCPLL TPWRT TFRC + TLOCK 2, 3, 4 XT, HS, SOSC TPWRT TOST 2, 5 XTPLL, HSPLL TPWRT TFRC + TLOCK 2, 3, 4 All Others Any Clock — — None Note 1: TPOR = Power-on Reset delay. 2: TPWRT = 64 ms nominal if the Power-up Timer (PWRT) is enabled; otherwise, it is zero. 3: TFRC and TLPRC = RC oscillator start-up times. 4: TLOCK = PLL lock time. 5: TOST = Oscillator Start-up Timer (OST). A 10-bit counter waits 1024 oscillator periods before releasing the oscillator clock to the system. 6: If Two-Speed Start-up is enabled, regardless of the primary oscillator selected, the device starts with FRC, and in such cases, FRC start-up time is valid. Note: For detailed operating frequency and timing specifications, see Section29.0 “Electrical Characteristics”. DS30009995E-page 72  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 7.2.1 POR AND LONG OSCILLATOR 7.5 Brown-out Reset (BOR) START-UP TIMES The PIC24FV32KA304 family devices implement a The oscillator start-up circuitry and its associated delay BOR circuit, which provides the user several timers are not linked to the device Reset delays that configuration and power-saving options. The BOR is occur at power-up. Some crystal circuits (especially controlled by the BORV<1:0> and BOREN<1:0> low-frequency crystals) will have a relatively long Configuration bits (FPOR<6:5,1:0>). There are a total start-up time. Therefore, one or more of the following of four BOR configurations, which are provided in conditions is possible after SYSRST is released: Table7-3. • The oscillator circuit has not begun to oscillate. The BOR threshold is set by the BORV<1:0> bits. If • The Oscillator Start-up Timer (OST) has not BOR is enabled (any values of BOREN<1:0>, except expired (if a crystal oscillator is used). ‘00’), any drop of VDD below the set threshold point will • The PLL has not achieved a lock (if PLL is used). reset the device. The chip will remain in BOR until VDD rises above the threshold. The device will not begin to execute code until a valid clock source has been released to the system. If the Power-up Timer is enabled, it will be invoked after Therefore, the oscillator and PLL start-up delays must VDD rises above the threshold. Then, it will keep the chip be considered when the Reset delay time must be in Reset for an additional time delay, TPWRT, if VDD known. drops below the threshold while the Power-up Timer is running. The chip goes back into a BOR and the 7.2.2 FAIL-SAFE CLOCK MONITOR Power-up Timer will be initialized. Once VDD rises above (FSCM) AND DEVICE RESETS the threshold, the Power-up Timer will execute the additional time delay. If the FSCM is enabled, it will begin to monitor the system clock source when SYSRST is released. If a BOR and the Power-up Timer (PWRT) are inde- valid clock source is not available at this time, the pendently configured. Enabling the Brown-out Reset device will automatically switch to the FRC oscillator does not automatically enable the PWRT. and the user can switch to the desired crystal oscillator in the Trap Service Routine (TSR). 7.5.1 SOFTWARE ENABLED BOR 7.3 Special Function Register Reset When BOREN<1:0> = 01, the BOR can be enabled or States disabled by the user in software. This is done with the control bit, SBOREN (RCON<13>). Setting SBOREN Most of the Special Function Registers (SFRs) enables the BOR to function as previously described. associated with the PIC24F CPU and peripherals are Clearing the SBOREN disables the BOR entirely. The reset to a particular value at a device Reset. The SFRs SBOREN bit operates only in this mode; otherwise, it is are grouped by their peripheral or CPU function and their read as ‘0’. Reset values are specified in each section of this manual. Placing BOR under software control gives the user the The Reset value for each SFR does not depend on the additional flexibility of tailoring the application to its type of Reset with the exception of four registers. The environment without having to reprogram the device to Reset value for the Reset Control register, RCON, will change the BOR configuration. It also allows the user depend on the type of device Reset. The Reset value for to tailor the incremental current that the BOR the Oscillator Control register, OSCCON, will depend on consumes. While the BOR current is typically very the type of Reset and the programmed values of the small, it may have some impact in low-power FNOSCx bits in the Flash Configuration Word applications. (FOSCSEL<2:0>); see Table7-2. The RCFGCAL and NVMCON registers are only affected by a POR. Note: Even when the BOR is under software con- trol, the Brown-out Reset voltage level is 7.4 Deep Sleep BOR (DSBOR) still set by the BORV<1:0> Configuration bits; it cannot be changed in software. Deep Sleep BOR is a very low-power BOR circuitry, used when the device is in Deep Sleep mode. Due to low current consumption, accuracy may vary. The DSBOR trip point is around 2.0V. DSBOR is enabled by configuring DSLPBOR (FDS<6>) = 1. DSLPBOR will re-arm the POR to ensure the device will reset if VDD drops below the POR threshold.  2011-2017 Microchip Technology Inc. DS30009995E-page 73

PIC24FV32KA304 FAMILY 7.5.2 DETECTING BOR 7.5.3 DISABLING BOR IN SLEEP MODE When BOR is enabled, the BOR bit (RCON<1>) is When BOREN<1:0> = 10, BOR remains under always reset to ‘1’ on any BOR or POR event. This hardware control and operates as previously makes it difficult to determine if a BOR event has described. However, whenever the device enters Sleep occurred just by reading the state of BOR alone. A mode, BOR is automatically disabled. When the device more reliable method is to simultaneously check the returns to any other operating mode, BOR is state of both POR and BOR. This assumes that the automatically re-enabled. POR and BOR bits are reset to ‘0’ in the software This mode allows for applications to recover from immediately after any POR event. If the BOR bit is ‘1’ brown-out situations, while actively executing code while POR is ‘0’, it can be reliably assumed that a BOR when the device requires BOR protection the most. At event has occurred. the same time, it saves additional power in Sleep mode by eliminating the small incremental BOR current. Note: Even when the device exits from Deep Sleep mode, both the POR and BOR bits Note: BOR levels differ depending on device type; are set. PIC24FV32KA3XX devices are at different levels than those of PIC24F32KA3XX devices. See Section29.0 “Electrical Characteristics” for BOR voltage levels. DS30009995E-page 74  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 8.0 INTERRUPT CONTROLLER 8.1.1 ALTERNATE INTERRUPT VECTOR TABLE (AIVT) Note: This data sheet summarizes the features The Alternate Interrupt Vector Table (AIVT) is located of this group of PIC24F devices. It is not after the IVT, as shown in Figure8-1. Access to the intended to be a comprehensive refer- AIVT is provided by the ALTIVT control bit ence source. For more information on the (INTCON2<15>). If the ALTIVT bit is set, all interrupt Interrupt Controller, refer to the and exception processes will use the alternate vectors “dsPIC33/PIC24 Family Reference instead of the default vectors. The alternate vectors are Manual”, “Interrupts” (DS70000600). organized in the same manner as the default vectors. The PIC24F interrupt controller reduces the numerous The AIVT supports emulation and debugging efforts by peripheral interrupt request signals to a single interrupt providing a means to switch between an application request signal to the CPU. It has the following features: and a support environment without requiring the inter- • Up to Eight Processor Exceptions and rupt vectors to be reprogrammed. This feature also Software Traps enables switching between applications for evaluation of different software algorithms at run time. If the AIVT • Seven User-Selectable Priority Levels is not needed, the AIVT should be programmed with • Interrupt Vector Table (IVT) with up to 118 Vectors the same addresses used in the IVT. • Unique Vector for each Interrupt or Exception Source 8.2 Reset Sequence • Fixed Priority within a Specified User Priority Level • Alternate Interrupt Vector Table (AIVT) for Debug A device Reset is not a true exception, because the Support interrupt controller is not involved in the Reset process. The PIC24F devices clear their registers in response to • Fixed Interrupt Entry and Return Latencies a Reset, which forces the Program Counter (PC) to zero. The microcontroller then begins program 8.1 Interrupt Vector Table (IVT) execution at location, 000000h. The user programs a The IVT is shown in Figure8-1. The IVT resides in the GOTO instruction at the Reset address, which redirects program memory, starting at location, 000004h. The IVT the program execution to the appropriate start-up contains 126 vectors, consisting of eight non-maskable routine. trap vectors, plus up to 118 sources of interrupt. In Note: Any unimplemented or unused vector general, each interrupt source has its own vector. Each locations in the IVT and AIVT should be interrupt vector contains a 24-bit wide address. The programmed with the address of a default value programmed into each interrupt vector location is interrupt handler routine that contains a the starting address of the associated Interrupt Service RESET instruction. Routine (ISR). Interrupt vectors are prioritized in terms of their natural priority; this is linked to their position in the vector table. All other things being equal, lower addresses have a higher natural priority. For example, the interrupt associated with Vector 0 will take priority over interrupts at any other vector address. PIC24FV32KA304 family devices implement non-maskable traps and unique interrupts; these are summarized in Table8-1 and Table8-2.  2011-2017 Microchip Technology Inc. DS30009995E-page 75

PIC24FV32KA304 FAMILY FIGURE 8-1: PIC24F INTERRUPT VECTOR TABLE Reset – GOTO Instruction 000000h Reset – GOTO Address 000002h Reserved 000004h Oscillator Fail Trap Vector Address Error Trap Vector Stack Error Trap Vector Math Error Trap Vector Reserved Reserved Reserved Interrupt Vector 0 000014h Interrupt Vector 1 — — — Interrupt Vector 52 00007Ch y Interrupt Vector Table (IVT)(1) orit Interrupt Vector 53 00007Eh Pri Interrupt Vector 54 000080h er — d — Or — ural Interrupt Vector 116 0000FCh at Interrupt Vector 117 0000FEh N g Reserved 000100h n Reserved 000102h si a Reserved e cr Oscillator Fail Trap Vector e D Address Error Trap Vector Stack Error Trap Vector Math Error Trap Vector Reserved Reserved Reserved Interrupt Vector 0 000114h Interrupt Vector 1 — — — Alternate Interrupt Vector Table (AIVT)(1) Interrupt Vector 52 00017Ch Interrupt Vector 53 00017Eh Interrupt Vector 54 000180h — — — Interrupt Vector 116 Interrupt Vector 117 0001FEh Start of Code 000200h Note 1: See Table8-2 for the interrupt vector list. DS30009995E-page 76  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY TABLE 8-1: TRAP VECTOR DETAILS Vector Number IVT Address AIVT Address Trap Source 0 000004h 000104h Reserved 1 000006h 000106h Oscillator Failure 2 000008h 000108h Address Error 3 00000Ah 00010Ah Stack Error 4 00000Ch 00010Ch Math Error 5 00000Eh 00010Eh Reserved 6 000010h 000110h Reserved 7 000012h 000112h Reserved TABLE 8-2: IMPLEMENTED INTERRUPT VECTORS Interrupt Bit Locations AIVT Interrupt Source Vector Number IVT Address Address Flag Enable Priority ADC1 Conversion Done 13 00002Eh 00012Eh IFS0<13> IEC0<13> IPC3<6:4> Comparator Event 18 000038h 000138h IFS1<2> IEC1<2> IPC4<10:8> CRC Generator 67 00009Ah 00019Ah IFS4<3> IEC4<3> IPC16<14:12> CTMU 77 0000AEh 0001AEh IFS4<13> IEC4<13> IPC19<6:4> External Interrupt 0 0 000014h 000114h IFS0<0> IEC0<0> IPC0<2:0> External Interrupt 1 20 00003Ch 00013Ch IFS1<4> IEC1<4> IPC5<2:0> External Interrupt 2 29 00004Eh 00014Eh IFS1<13> IEC1<13> IPC7<6:4> I2C1 Master Event 17 000036h 000136h IFS1<1> IEC1<1> IPC4<6:4> I2C1 Slave Event 16 000034h 000134h IFS1<0> IEC1<0> IPC4<2:0> I2C2 Master Event 50 000078h 000178h IFS3<2> IEC3<2> IPC12<10:8> I2C2 Slave Event 49 000076h 000176h IFS3<1> IEC3<1> IPC12<6:4> Input Capture 1 1 000016h 000116h IFS0<1> IEC0<1> IPC0<6:4> Input Capture 2 5 00001Eh 00011Eh IFS0<5> IEC0<5> IPC1<6:4> Input Capture 3 37 00005Eh 00015Eh IFS2<5> IEC2<5> IPC9<6:4> Input Change Notification 19 00003Ah 00013Ah IFS1<3> IEC1<3> IPC4<14:12> HLVD (High/Low-Voltage Detect) 72 0000A4h 0001A4h IFS4<8> IEC4<8> IPC17<2:0> NVM – NVM Write Complete 15 000032h 000132h IFS0<15> IEC0<15> IPC3<14:12> Output Compare 1 2 000018h 000118h IFS0<2> IEC0<2> IPC0<10:8> Output Compare 2 6 000020h 000120h IFS0<6> IEC0<6> IPC1<10:8> Output Compare 3 25 000046h 000146h IFS1<9> IEC1<9> IPC6<6:4> Real-Time Clock/Calendar 62 000090h 000190h IFS3<14> IEC3<14> IPC15<10:8> SPI1 Error 9 000026h 000126h IFS0<9> IEC0<9> IPC2<6:4> SPI1 Event 10 000028h 000128h IFS0<10> IEC0<10> IPC2<10:8> SPI2 Error 32 000054h 000154h IFS2<0> IEC2<2> IPC8<2:0> SPI2 Event 33 000056h 000156h IFS2<1> IEC2<1> IPC8<6:4> Timer1 3 00001Ah 00011Ah IFS0<3> IEC0<3> IPC0<14:12> Timer2 7 000022h 000122h IFS0<7> IEC0<7> IPC1<14:12> Timer3 8 000024h 000124h IFS0<8> IEC0<8> IPC2<2:0> Timer4 27 00004Ah 00014Ah IFS1<11> IEC1<11> IPC6<14:12> Timer5 28 00004Ch 00015Ch IFS1<12> IEC1<12> IPC7<2:0> UART1 Error 65 000096h 000196h IFS4<1> IEC4<1> IPC16<6:4> UART1 Receiver 11 00002Ah 00012Ah IFS0<11> IEC0<11> IPC2<14:12> UART1 Transmitter 12 00002Ch 00012Ch IFS0<12> IEC0<12> IPC3<2:0> UART2 Error 66 000098h 000198h IFS4<2> IEC4<2> IPC16<10:8> UART2 Receiver 30 000050h 000150h IFS1<14> IEC1<14> IPC7<10:8> UART2 Transmitter 31 000052h 000152h IFS1<15> IEC1<15> IPC7<14:12> Ultra Low-Power Wake-up 80 0000B4h 0001B4h IFS5<0> IEC5<0> IPC20<2:0>  2011-2017 Microchip Technology Inc. DS30009995E-page 77

PIC24FV32KA304 FAMILY 8.3 Interrupt Control and Status The INTTREG register contains the associated Registers interrupt vector number and the new CPU Interrupt Priority Level, which are latched into the Vector The PIC24FV32KA304 family of devices implements a Number (VECNUM<6:0>) and the Interrupt Level total of 23 registers for the interrupt controller: (ILR<3:0>) bit fields in the INTTREG register. The new • INTCON1 Interrupt Priority Level is the priority of the pending interrupt. • INTCON2 • IFS0, IFS1, IFS3 and IFS4 The interrupt sources are assigned to the IFSx, IECx and IPCx registers in the same sequence listed in • IEC0, IEC1, IEC3 and IEC4 Table8-2. For example, the INT0 (External Interrupt 0) • IPC0 through IPC5, IPC7 and IPC15 through is depicted as having a vector number and a natural IPC19 order priority of 0. The INT0IF status bit is found in • INTTREG IFS0<0>, the INT0IE enable bit in IEC0<0> and the Global Interrupt Enable (GIE) control functions are INT0IP<2:0> priority bits are in the first position of IPC0 controlled from INTCON1 and INTCON2. INTCON1 (IPC0<2:0>). contains the Interrupt Nesting Disable (NSTDIS) bit, as Although they are not specifically part of the interrupt well as the control and status flags for the processor control hardware, two of the CPU Control registers con- trap sources. The INTCON2 register controls the tain bits that control interrupt functionality. The ALU external interrupt request signal behavior and the use STATUS Register (SR) contains the IPL<2:0> bits of the AIVT. (SR<7:5>). These indicate the current CPU Interrupt The IFSx registers maintain all of the interrupt request Priority Level. The user may change the current CPU flags. Each source of interrupt has a status bit, which is Interrupt Priority Level by writing to the IPLx bits. set by the respective peripherals, or external signal, The CORCON register contains the IPL3 bit, which and is cleared via software. together with IPL<2:0>, also indicates the current CPU The IECx registers maintain all of the interrupt enable Interrupt Priority Level. IPL3 is a read-only bit so that the bits. These control bits are used to individually enable trap events cannot be masked by the user’s software. interrupts from the peripherals or external signals. All Interrupt registers are described in Register8-1 The IPCx registers are used to set the Interrupt Priority through Register8-33, in the following sections. Level (IPL) for each source of interrupt. Each user interrupt source can be assigned to one of eight priority levels. DS30009995E-page 78  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 8-1: SR: ALU STATUS REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 R-0, HSC — — — — — — — DC(1) bit 15 bit 8 R/W-0, HSC R/W-0, HSC R/W-0, HSC R-0, HSC R/W-0, HSC R/W-0, HSC R/W-0, HSC R/W-0, HSC IPL2(2,3) IPL1(2,3) IPL0(2,3) RA(1) N(1) OV(1) Z(1) C(1) bit 7 bit 0 Legend: HSC = Hardware Settable/Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-9 Unimplemented: Read as ‘0’ bit 7-5 IPL<2:0>: CPU Interrupt Priority Level Status bits(2,3) 111 = CPU Interrupt Priority Level is 7 (15); user interrupts are disabled 110 = CPU Interrupt Priority Level is 6 (14) 101 = CPU Interrupt Priority Level is 5 (13) 100 = CPU Interrupt Priority Level is 4 (12) 011 = CPU Interrupt Priority Level is 3 (11) 010 = CPU Interrupt Priority Level is 2 (10) 001 = CPU Interrupt Priority Level is 1 (9) 000 = CPU Interrupt Priority Level is 0 (8) Note 1: See Register3-1 for the description of these bits, which are not dedicated to interrupt control functions. 2: The IPL<2:0> bits are concatenated with the IPL3 bit (CORCON<3>) to form the CPU Interrupt Priority Level. The value in parentheses indicates the Interrupt Priority Level if IPL3 = 1. 3: The IPLx Status bits are read-only when NSTDIS (INTCON1<15>) = 1. Note: Bit 8 and bits 4 through 0 are described in Section 3.0 “CPU”.  2011-2017 Microchip Technology Inc. DS30009995E-page 79

PIC24FV32KA304 FAMILY REGISTER 8-2: CORCON: CPU CONTROL REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 U-0 U-0 R/C-0, HSC R/W-0 U-0 U-0 — — — — IPL3(2) PSV(1) — — bit 7 bit 0 Legend: C = Clearable bit HSC = Hardware Settable/Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-4 Unimplemented: Read as ‘0’ bit 3 IPL3: CPU Interrupt Priority Level Status bit(2) 1 = CPU Interrupt Priority Level is greater than 7 0 = CPU Interrupt Priority Level is 7 or less bit 1-0 Unimplemented: Read as ‘0’ Note 1: See Register3-2 for the description of this bit, which is not dedicated to interrupt control functions. 2: The IPL3 bit is concatenated with the IPL<2:0> bits (SR<7:5>) to form the CPU Interrupt Priority Level. Note: Bit 2 is described in Section 3.0 “CPU”. DS30009995E-page 80  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 8-3: INTCON1: INTERRUPT CONTROL REGISTER 1 R/W-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 NSTDIS — — — — — — — bit 15 bit 8 U-0 U-0 U-0 R/W-0, HS R/W-0, HS R/W-0, HS R/W-0, HS U-0 — — — MATHERR ADDRERR STKERR OSCFAIL — bit 7 bit 0 Legend: HS = Hardware Settable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 NSTDIS: Interrupt Nesting Disable bit 1 = Interrupt nesting is disabled 0 = Interrupt nesting is enabled bit 14-5 Unimplemented: Read as ‘0’ bit 4 MATHERR: Arithmetic Error Trap Status bit 1 = Overflow trap has occurred 0 = Overflow trap has not occurred bit 3 ADDRERR: Address Error Trap Status bit 1 = Address error trap has occurred 0 = Address error trap has not occurred bit 2 STKERR: Stack Error Trap Status bit 1 = Stack error trap has occurred 0 = Stack error trap has not occurred bit 1 OSCFAIL: Oscillator Failure Trap Status bit 1 = Oscillator failure trap has occurred 0 = Oscillator failure trap has not occurred bit 0 Unimplemented: Read as ‘0’  2011-2017 Microchip Technology Inc. DS30009995E-page 81

PIC24FV32KA304 FAMILY REGISTER 8-4: INTCON2: INTERRUPT CONTROL REGISTER2 R/W-0 R-0, HSC U-0 U-0 U-0 U-0 U-0 U-0 ALTIVT DISI — — — — — — bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 — — — — — INT2EP INT1EP INT0EP bit 7 bit 0 Legend: HSC = Hardware Settable/Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 ALTIVT: Enable Alternate Interrupt Vector Table bit 1 = Uses Alternate Interrupt Vector Table (AIVT) 0 = Uses standard (default) Interrupt Vector Table (IVT) bit 14 DISI: DISI Instruction Status bit 1 = DISI instruction is active 0 = DISI instruction is not active bit 13-3 Unimplemented: Read as ‘0’ bit 2 INT2EP: External Interrupt 2 Edge Detect Polarity Select bit 1 = Interrupt is on the negative edge 0 = Interrupt is on the positive edge bit 1 INT1EP: External Interrupt 1 Edge Detect Polarity Select bit 1 = Interrupt is on the negative edge 0 = Interrupt is on the positive edge bit 0 INT0EP: External Interrupt 0 Edge Detect Polarity Select bit 1 = Interrupt is on the negative edge 0 = Interrupt is on the positive edge DS30009995E-page 82  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 8-5: IFS0: INTERRUPT FLAG STATUS REGISTER 0 R/W-0, HS U-0 R/W-0, HS R/W-0, HS R/W-0, HS R/W-0, HS R/W-0, HS R/W-0, HS NVMIF — AD1IF U1TXIF U1RXIF SPI1IF SPF1IF T3IF bit 15 bit 8 R/W-0, HS R/W-0, HS R/W-0, HS U-0 R/W-0, HS R/W-0, HS R/W-0, HS R/W-0, HS T2IF OC2IF IC2IF — T1IF OC1IF IC1IF INT0IF bit 7 bit 0 Legend: HS = Hardware Settable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 NVMIF: NVM Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 14 Unimplemented: Read as ‘0’ bit 13 AD1IF: A/D Conversion Complete Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 12 U1TXIF: UART1 Transmitter Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 11 U1RXIF: UART1 Receiver Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 10 SPI1IF: SPI1 Event Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 9 SPF1IF: SPI1 Fault Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 8 T3IF: Timer3 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 7 T2IF: Timer2 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 6 OC2IF: Output Compare Channel 2 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 5 IC2IF: Input Capture Channel 2 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 4 Unimplemented: Read as ‘0’ bit 3 T1IF: Timer1 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred  2011-2017 Microchip Technology Inc. DS30009995E-page 83

PIC24FV32KA304 FAMILY REGISTER 8-5: IFS0: INTERRUPT FLAG STATUS REGISTER 0 (CONTINUED) bit 2 OC1IF: Output Compare Channel 1 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 1 IC1IF: Input Capture Channel 1 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 0 INT0IF: External Interrupt 0 Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred DS30009995E-page 84  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 8-6: IFS1: INTERRUPT FLAG STATUS REGISTER 1 R/W-0, HS R/W-0, HS R/W-0, HS R/W-0, HS R/W-0, HS U-0 R/W-0, HS U-0 U2TXIF U2RXIF INT2IF T5IF T4IF — OC3IF — bit 15 bit 8 U-0 U-0 U-0 R/W-0, HS R/W-0, HS R/W-0, HS R/W-0 R/W-0 — — — INT1IF CNIF CMIF MI2C1IF SI2C1IF bit 7 bit 0 Legend: HS = Hardware Settable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 U2TXIF: UART2 Transmitter Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 14 U2RXIF: UART2 Receiver Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 13 INT2IF: External Interrupt 2 Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 12 T5IF: Timer5 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 11 T4IF: Timer4 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 10 Unimplemented: Read as ‘0’ bit 9 OC3IF: Output Compare Channel 3 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 8-5 Unimplemented: Read as ‘0’ bit 4 INT1IF: External Interrupt 1 Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 3 CNIF: Input Change Notification Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 2 CMIF: Comparator Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 1 MI2C1IF: Master I2C1 Event Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 0 SI2C1IF: Slave I2C1 Event Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred  2011-2017 Microchip Technology Inc. DS30009995E-page 85

PIC24FV32KA304 FAMILY REGISTER 8-7: IFS2: INTERRUPT FLAG STATUS REGISTER 2 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 R/W-0, HS U-0 U-0 U-0 R/W-0, HS R/W-0, HS — — IC3IF — — — SPI2IF SPF2IF bit 7 bit 0 Legend: HS = Hardware Settable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-6 Unimplemented: Read as ‘0’ bit 5 IC3IF: Input Capture Channel 3 Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 4-2 Unimplemented: Read as ‘0’ bit 1 SPI2IF: SPI2 Event Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 0 SPF2IF: SPI2 Fault Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred DS30009995E-page 86  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 8-8: IFS3: INTERRUPT FLAG STATUS REGISTER 3 U-0 R/W-0, HS U-0 U-0 U-0 U-0 U-0 U-0 — RTCIF — — — — — — bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 R/W-0, HS R/W-0, HS U-0 — — — — — MI2C2IF SI2C2IF — bit 7 bit 0 Legend: HS = Hardware Settable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 Unimplemented: Read as ‘0’ bit 14 RTCIF: Real-Time Clock and Calendar Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 13-3 Unimplemented: Read as ‘0’ bit 2 MI2C2IF: Master I2C2 Event Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 1 SI2C2IF: Slave I2C2 Event Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 0 Unimplemented: Read as ‘0’  2011-2017 Microchip Technology Inc. DS30009995E-page 87

PIC24FV32KA304 FAMILY REGISTER 8-9: IFS4: INTERRUPT FLAG STATUS REGISTER 4 U-0 U-0 R/W-0, HS U-0 U-0 U-0 U-0 R/W-0, HS — — CTMUIF — — — — HLVDIF bit 15 bit 8 U-0 U-0 U-0 U-0 R/W-0, HS R/W-0, HS R/W-0, HS U-0 — — — — CRCIF U2ERIF U1ERIF — bit 7 bit 0 Legend: HS = Hardware Settable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13 CTMUIF: CTMU Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 12-9 Unimplemented: Read as ‘0’ bit 8 HLVDIF: High/Low-Voltage Detect Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 7-4 Unimplemented: Read as ‘0’ bit 3 CRCIF: CRC Generator Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 2 U2ERIF: UART2 Error Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 1 U1ERIF: UART1 Error Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred bit 0 Unimplemented: Read as ‘0’ DS30009995E-page 88  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 8-10: IFS5: INTERRUPT FLAG STATUS REGISTER 5 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0, HS — — — — — — — ULPWUIF bit 7 bit 0 Legend: HS = Hardware Settable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-1 Unimplemented: Read as ‘0’ bit 0 ULPWUIF: Ultra Low-Power Wake-up Interrupt Flag Status bit 1 = Interrupt request has occurred 0 = Interrupt request has not occurred  2011-2017 Microchip Technology Inc. DS30009995E-page 89

PIC24FV32KA304 FAMILY REGISTER 8-11: IEC0: INTERRUPT ENABLE CONTROL REGISTER 0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 NVMIE — AD1IE U1TXIE U1RXIE SPI1IE SPF1IE T3IE bit 15 bit 8 R/W-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 T2IE OC2IE IC2IE — T1IE OC1IE IC1IE INT0IE bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 NVMIE: NVM Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled bit 14 Unimplemented: Read as ‘0’ bit 13 AD1IE: A/D Conversion Complete Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled bit 12 U1TXIE: UART1 Transmitter Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled bit 11 U1RXIE: UART1 Receiver Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled bit 10 SPI1IE: SPI1 Transfer Complete Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled bit 9 SPF1IE: SPI1 Fault Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled bit 8 T3IE: Timer3 Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled bit 7 T2IE: Timer2 Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled bit 6 OC2IE: Output Compare Channel 2 Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled bit 5 IC2IE: Input Capture Channel 2 Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled bit 4 Unimplemented: Read as ‘0’ bit 3 T1IE: Timer1 Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled bit 2 OC1IE: Output Compare Channel 1 Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled DS30009995E-page 90  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 8-11: IEC0: INTERRUPT ENABLE CONTROL REGISTER 0 (CONTINUED) bit 1 IC1IE: Input Capture Channel 1 Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled bit 0 INT0IE: External Interrupt 0 Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled  2011-2017 Microchip Technology Inc. DS30009995E-page 91

PIC24FV32KA304 FAMILY REGISTER 8-12: IEC1: INTERRUPT ENABLE CONTROL REGISTER 1 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 U-0 R/W-0 U-0 U2TXIE U2RXIE INT2IE T5IE T4IE — OC3IE — bit 15 bit 8 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — — INT1IE CNIE CMIE MI2C1IE SI2C1IE bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 U2TXIE: UART2 Transmitter Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled bit 14 U2RXIE: UART2 Receiver Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled bit 13 INT2IE: External Interrupt 2 Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled bit 12 T5IE: Timer5 Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled bit 11 T4IE: Timer4 Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled bit 10 Unimplemented: Read as ‘0’ bit 9 OC3IE: Output Compare 3 Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled bit 8-5 Unimplemented: Read as ‘0’ bit 4 INT1IE: External Interrupt 1 Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled bit 3 CNIE: Input Change Notification Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled bit 2 CMIE: Comparator Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled bit 1 MI2C1IE: Master I2C1 Event Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled bit 0 SI2C1IE: Slave I2C1 Event Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled DS30009995E-page 92  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 8-13: IEC2: INTERRUPT ENABLE CONTROL REGISTER 2 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 R/W-0 U-0 U-0 U-0 R/W-0 R/W-0 — — IC3IE — — — SPI2IE SPF2IE bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-6 Unimplemented: Read as ‘0’ bit 5 IC3IE: Input Capture Channel 3 Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled bit 4-2 Unimplemented: Read as ‘0’ bit 1 SPI2IE: SPI2 Event Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled bit 0 SPF2IE: SPI2 Fault Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled  2011-2017 Microchip Technology Inc. DS30009995E-page 93

PIC24FV32KA304 FAMILY REGISTER 8-14: IEC3: INTERRUPT ENABLE CONTROL REGISTER 3 U-0 R/W-0 U-0 U-0 U-0 U-0 U-0 U-0 — RTCIE — — — — — — bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 U-0 — — — — — MI2C2IE SI2C2IE — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 Unimplemented: Read as ‘0’ bit 14 RTCIE: Real-Time Clock and Calendar Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled bit 13-3 Unimplemented: Read as ‘0’ bit 2 MI2C2IE: Master I2C2 Event Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled bit 1 SI2C2IE: Slave I2C2 Event Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled bit 0 Unimplemented: Read as ‘0’ DS30009995E-page 94  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 8-15: IEC4: INTERRUPT ENABLE CONTROL REGISTER 4 U-0 U-0 R/W-0 U-0 U-0 U-0 U-0 R/W-0 — — CTMUIE — — — — HLVDIE bit 15 bit 8 U-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 U-0 — — — — CRCIE U2ERIE U1ERIE — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13 CTMUIE: CTMU Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled bit 12-9 Unimplemented: Read as ‘0’ bit 8 HLVDIE: High/Low-Voltage Detect Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled bit 7-4 Unimplemented: Read as ‘0’ bit 3 CRCIE: CRC Generator Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled bit 2 U2ERIE: UART2 Error Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled bit 1 U1ERIE: UART1 Error Interrupt Enable bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled bit 0 Unimplemented: Read as ‘0’  2011-2017 Microchip Technology Inc. DS30009995E-page 95

PIC24FV32KA304 FAMILY REGISTER 8-16: IEC5: INTERRUPT ENABLE CONTROL REGISTER 5 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 — — — — — — — ULPWUIE bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-1 Unimplemented: Read as ‘0’ bit 0 ULPWUIE: Ultra Low-Power Wake-up Interrupt Enable Bit 1 = Interrupt request is enabled 0 = Interrupt request is not enabled DS30009995E-page 96  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 8-17: IPC0: INTERRUPT PRIORITY CONTROL REGISTER 0 U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0 — T1IP2 T1IP1 T1IP0 — OC1IP2 OC1IP1 OC1IP0 bit 15 bit 8 U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0 — IC1IP2 IC1IP1 IC1IP0 — INT0IP2 INT0IP1 INT0IP0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 Unimplemented: Read as ‘0’ bit 14-12 T1IP<2:0>: Timer1 Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 11 Unimplemented: Read as ‘0’ bit 10-8 OC1IP<2:0>: Output Compare Channel 1 Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 7 Unimplemented: Read as ‘0’ bit 6-4 IC1IP<2:0>: Input Capture Channel 1 Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 3 Unimplemented: Read as ‘0’ bit 2-0 INT0IP<2:0>: External Interrupt 0 Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled  2011-2017 Microchip Technology Inc. DS30009995E-page 97

PIC24FV32KA304 FAMILY REGISTER 8-18: IPC1: INTERRUPT PRIORITY CONTROL REGISTER 1 U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0 — T2IP2 T2IP1 T2IP0 — OC2IP2 OC2IP1 OC2IP0 bit 15 bit 8 U-0 R/W-1 R/W-0 R/W-0 U-0 U-0 U-0 U-0 — IC2IP2 IC2IP1 IC2IP0 — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 Unimplemented: Read as ‘0’ bit 14-12 T2IP<2:0>: Timer2 Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 11 Unimplemented: Read as ‘0’ bit 10-8 OC2IP<2:0>: Output Compare Channel 2 Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 7 Unimplemented: Read as ‘0’ bit 6-4 IC2IP<2:0>: Input Capture Channel 2 Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 3-0 Unimplemented: Read as ‘0’ DS30009995E-page 98  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 8-19: IPC2: INTERRUPT PRIORITY CONTROL REGISTER 2 U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0 — U1RXIP2 U1RXIP1 U1RXIP0 — SPI1IP2 SPI1IP1 SPI1IP0 bit 15 bit 8 U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0 — SPF1IP2 SPF1IP1 SPF1IP0 — T3IP2 T3IP1 T3IP0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 Unimplemented: Read as ‘0’ bit 14-12 U1RXIP<2:0>: UART1 Receiver Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 11 Unimplemented: Read as ‘0’ bit 10-8 SPI1IP<2:0>: SPI1 Event Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 7 Unimplemented: Read as ‘0’ bit 6-4 SPF1IP<2:0>: SPI1 Fault Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 3 Unimplemented: Read as ‘0’ bit 2-0 T3IP<2:0>: Timer3 Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled  2011-2017 Microchip Technology Inc. DS30009995E-page 99

PIC24FV32KA304 FAMILY REGISTER 8-20: IPC3: INTERRUPT PRIORITY CONTROL REGISTER 3 U-0 R/W-1 R/W-0 R/W-0 U-0 U-0 U-0 U-0 — NVMIP2 NVMIP1 NVMIP0 — — — — bit 15 bit 8 U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0 — AD1IP2 AD1IP1 AD1IP0 — U1TXIP2 U1TXIP1 U1TXIP0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 Unimplemented: Read as ‘0’ bit 14-12 NVMIP<2:0>: NVM Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 11-7 Unimplemented: Read as ‘0’ bit 6-4 AD1IP<2:0>: A/D Conversion Complete Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 3 Unimplemented: Read as ‘0’ bit 2-0 U1TXIP<2:0>: UART1 Transmitter Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled DS30009995E-page 100  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 8-21: IPC4: INTERRUPT PRIORITY CONTROL REGISTER 4 U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0 — CNIP2 CNIP1 CNIP0 — CMIP2 CMIP1 CMIP0 bit 15 bit 8 U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0 — MI2C1P2 MI2C1P1 MI2C1P0 — SI2C1P2 SI2C1P1 SI2C1P0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 Unimplemented: Read as ‘0’ bit 14-12 CNIP<2:0>: Input Change Notification Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 11 Unimplemented: Read as ‘0’ bit 10-8 CMIP<2:0>: Comparator Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 7 Unimplemented: Read as ‘0’ bit 6-4 MI2C1P<2:0>: Master I2C1 Event Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 3 Unimplemented: Read as ‘0’ bit 2-0 SI2C1P<2:0>: Slave I2C1 Event Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled  2011-2017 Microchip Technology Inc. DS30009995E-page 101

PIC24FV32KA304 FAMILY REGISTER 8-22: IPC5: INTERRUPT PRIORITY CONTROL REGISTER 5 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 R/W-1 R/W-0 R/W-0 — — — — — INT1IP2 INT1IP1 INT1IP0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-3 Unimplemented: Read as ‘0’ bit 2-0 INT1IP<2:0>: External Interrupt 1 Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled DS30009995E-page 102  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 8-23: IPC6: INTERRUPT PRIORITY CONTROL REGISTER 6 U-0 R/W-1 R/W-0 R/W-0 U-0 U-0 U-0 U-0 — T4IP2 T4IP1 T4IP0 — — — — bit 15 bit 8 U-0 R/W-1 R/W-0 R/W-0 U-0 U-0 U-0 U-0 — OC3IP2 OC3IP1 OC3IP0 — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 Unimplemented: Read as ‘0’ bit 14-12 T4IP<2:0>: Timer4 Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 11-7 Unimplemented: Read as ‘0’ bit 6-4 OC3IP<2:0>: Output Compare Channel 3 Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 3-0 Unimplemented: Read as ‘0’  2011-2017 Microchip Technology Inc. DS30009995E-page 103

PIC24FV32KA304 FAMILY REGISTER 8-24: IPC7: INTERRUPT PRIORITY CONTROL REGISTER 7 U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0 — U2TXIP2 U2TXIP1 U2TXIP0 — U2RXIP2 U2RXIP1 U2RXIP0 bit 15 bit 8 U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0 — INT2IP2 INT2IP1 INT2IP0 — T5IP2 T5IP1 T5IP0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 Unimplemented: Read as ‘0’ bit 14-12 U2TXIP<2:0>: UART2 Transmitter Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 11 Unimplemented: Read as ‘0’ bit 10-8 U2RXIP<2:0>: UART2 Receiver Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 7 Unimplemented: Read as ‘0’ bit 6-4 INT2IP<2:0>: External Interrupt 2 Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 3 Unimplemented: Read as ‘0’ bit 2-0 T5IP<2:0>: Timer5 Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled DS30009995E-page 104  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 8-25: IPC8: INTERRUPT PRIORITY CONTROL REGISTER 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0 — SPI2IP2 SPI2IP1 SPI2IP0 — SPF2IP2 SPF2IP1 SPF2IP0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-7 Unimplemented: Read as ‘0’ bit 6-4 SPI2IP<2:0>: SPI2 Event Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 3 Unimplemented: Read as ‘0’ bit 2-0 SPF2IP<2:0>: SPI2 Fault Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled  2011-2017 Microchip Technology Inc. DS30009995E-page 105

PIC24FV32KA304 FAMILY REGISTER 8-26: IPC9: INTERRUPT PRIORITY CONTROL REGISTER 9 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 R/W-1 R/W-0 R/W-0 U-0 U-0 U-0 U-0 — IC3IP2 IC3IP1 IC3IP0 — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-7 Unimplemented: Read as ‘0’ bit 6-4 IC3IP<2:0>: Input Capture Channel 3 Event Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 3-0 Unimplemented: Read as ‘0’ DS30009995E-page 106  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 8-27: IPC12: INTERRUPT PRIORITY CONTROL REGISTER 12 U-0 U-0 U-0 U-0 U-0 R/W-1 R/W-0 R/W-0 — — — — — MI2C2IP2 MI2C2IP1 MI2C2IP0 bit 15 bit 8 U-0 R/W-1 R/W-0 R/W-0 U-0 U-0 U-0 U-0 — SI2C2IP2 SI2C2IP1 SI2C2IP0 — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-11 Unimplemented: Read as ‘0’ bit 10-8 MI2C2IP <2:0>: Master I2C2 Event Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 7 Unimplemented: Read as ‘0’ bit 6-4 SI2C2IP<2:0>: Slave I2C2 Event Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 3-0 Unimplemented: Read as ‘0’  2011-2017 Microchip Technology Inc. DS30009995E-page 107

PIC24FV32KA304 FAMILY REGISTER 8-28: IPC15: INTERRUPT PRIORITY CONTROL REGISTER 15 U-0 U-0 U-0 U-0 U-0 R/W-1 R/W-0 R/W-0 — — — — — RTCIP2 RTCIP1 RTCIP0 bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-11 Unimplemented: Read as ‘0’ bit 10-8 RTCIP<2:0>: Real-Time Clock and Calendar Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 7-0 Unimplemented: Read as ‘0’ DS30009995E-page 108  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 8-29: IPC16: INTERRUPT PRIORITY CONTROL REGISTER 16 U-0 R/W-1 R/W-0 R/W-0 U-0 R/W-1 R/W-0 R/W-0 — CRCIP2 CRCIP1 CRCIP0 — U2ERIP2 U2ERIP1 U2ERIP0 bit 15 bit 8 U-0 R/W-1 R/W-0 R/W-0 U-0 U-0 U-0 U-0 — U1ERIP2 U1ERIP1 U1ERIP0 — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 Unimplemented: Read as ‘0’ bit 14-12 CRCIP<2:0>: CRC Generator Error Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 11 Unimplemented: Read as ‘0’ bit 10-8 U2ERIP<2:0>: UART2 Error Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 7 Unimplemented: Read as ‘0’ bit 6-4 U1ERIP<2:0>: UART1 Error Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 3-0 Unimplemented: Read as ‘0’  2011-2017 Microchip Technology Inc. DS30009995E-page 109

PIC24FV32KA304 FAMILY REGISTER 8-30: IPC18: INTERRUPT PRIORITY CONTROL REGISTER 18 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 R/W-1 R/W-0 R/W-0 — — — — — HLVDIP2 HLVDIP1 HLVDIP0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-3 Unimplemented: Read as ‘0’ bit 2-0 HLVDIP<2:0>: High/Low-Voltage Detect Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled REGISTER 8-31: IPC19: INTERRUPT PRIORITY CONTROL REGISTER 19 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 R/W-1 R/W-0 R/W-0 U-0 U-0 U-0 U-0 — CTMUIP2 CTMUIP1 CTMUIP0 — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-7 Unimplemented: Read as ‘0’ bit 6-4 CTMUIP<2:0>: CTMU Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled bit 3-0 Unimplemented: Read as ‘0’ DS30009995E-page 110  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 8-32: IPC20: INTERRUPT PRIORITY CONTROL REGISTER 20 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 R/W-1 R/W-0 R/W-0 — — — — — ULPWUIP2 ULPWUIP1 ULPWUIP0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-3 Unimplemented: Read as ‘0’ bit 6-4 ULPWUIP<2:0>: Ultra Low-Power Wake-up Interrupt Priority bits 111 = Interrupt is Priority 7 (highest priority interrupt) • • • 001 = Interrupt is Priority 1 000 = Interrupt source is disabled  2011-2017 Microchip Technology Inc. DS30009995E-page 111

PIC24FV32KA304 FAMILY REGISTER 8-33: INTTREG: INTERRUPT CONTROL AND STATUS REGISTER R-0 U-0 R/W-0 U-0 R-0 R-0 R-0 R-0 CPUIRQ — VHOLD — ILR3 ILR2 ILR1 ILR0 bit 15 bit 8 U-0 R-0 R-0 R-0 R-0 R-0 R-0 R-0 — VECNUM6 VECNUM5 VECNUM4 VECNUM3 VECNUM2 VECNUM1 VECNUM0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 CPUIRQ: Interrupt Request from Interrupt Controller CPU bit 1 = An interrupt request has occurred but has not yet been Acknowledged by the CPU (this will happen when the CPU priority is higher than the interrupt priority) 0 = No interrupt request is left unacknowledged bit 14 Unimplemented: Read as ‘0’ bit 13 VHOLD: Vector Hold bit Allows Vector Number Capture and Changes which Interrupt is Stored in the VECNUM bit: 1 = VECNUM will contain the value of the highest priority pending interrupt, instead of the current interrupt 0 = VECNUM will contain the value of the last Acknowledged interrupt (last interrupt that has occurred with higher priority than the CPU, even if other interrupts are pending) bit 12 Unimplemented: Read as ‘0’ bit 11-8 ILR<3:0>: New CPU Interrupt Priority Level bits 1111 = CPU Interrupt Priority Level is 15 • • • 0001 = CPU Interrupt Priority Level is 1 0000 = CPU Interrupt Priority Level is 0 bit 7 Unimplemented: Read as ‘0’ bit 6-0 VECNUM<6:0>: Vector Number of Pending Interrupt bits 0111111 = Interrupt vector pending is Number 135 • • • 0000001 = Interrupt vector pending is Number 9 0000000 = Interrupt vector pending is Number 8 DS30009995E-page 112  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 8.4 Interrupt Setup Procedures 8.4.3 TRAP SERVICE ROUTINE (TSR) A Trap Service Routine (TSR) is coded like an ISR, 8.4.1 INITIALIZATION except that the appropriate trap status flag in the To configure an interrupt source: INTCON1 register must be cleared to avoid re-entry into the TSR. 1. Set the NSTDIS control bit (INTCON1<15>) if nested interrupts are not desired. 8.4.4 INTERRUPT DISABLE 2. Select the user-assigned priority level for the interrupt source by writing the control bits in the All user interrupts can be disabled using the following appropriate IPCx register. The priority level will procedure: depend on the specific application and type of 1. Push the current SR value onto the software interrupt source. If multiple priority levels are not stack using the PUSH instruction. desired, the IPCx register control bits for all 2. Force the CPU to Priority Level 7 by inclusive enabled interrupt sources may be programmed ORing the value, OEh with SRL. to the same non-zero value. To enable user interrupts, the POP instruction may be Note: At a device Reset, the IPCx registers are used to restore the previous SR value. initialized, such that all user interrupt Only user interrupts with a priority level of 7 or less can sources are assigned to Priority Level 4. be disabled. Trap sources (Level8-15) cannot be 3. Clear the interrupt flag status bit associated with disabled. the peripheral in the associated IFSx register. The DISI instruction provides a convenient way to 4. Enable the interrupt source by setting the disable interrupts of Priority Levels 1-6 for a fixed interrupt enable control bit associated with the period. Level 7 interrupt sources are not disabled by source in the appropriate IECx register. the DISI instruction. 8.4.2 INTERRUPT SERVICE ROUTINE The method that is used to declare an ISR (Interrupt Service Routine) and initialize the IVT with the correct vector address depends on the programming language (i.e., C or assembly) and the language development toolsuite that is used to develop the application. In general, the user must clear the interrupt flag in the appropriate IFSx register for the source of the interrupt that the ISR handles. Otherwise, the ISR will be re-entered immediately after exiting the routine. If the ISR is coded in assembly language, it must be termi- nated using a RETFIE instruction to unstack the saved PC value, SRL value and old CPU priority level.  2011-2017 Microchip Technology Inc. DS30009995E-page 113

PIC24FV32KA304 FAMILY NOTES: DS30009995E-page 114  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 9.0 OSCILLATOR • Software-controllable switching between various CONFIGURATION clock sources. • Software-controllable postscaler for selective Note: This data sheet summarizes the features clocking of CPU for system power savings. of this group of PIC24F devices. It is not • System frequency range declaration bits for EC intended to be a comprehensive refer- mode. When using an external clock source, the ence source. For more information on current consumption is reduced by setting the Oscillator Configuration, refer to the declaration bits to the expected frequency range. “dsPIC33/PIC24 Family Reference • A Fail-Safe Clock Monitor (FSCM) that detects Manual”, “Oscillator with 500 kHz clock failure and permits safe application recovery Low-Power FRC” (DS39726). or shutdown. The oscillator system for the PIC24FV32KA304 family A simplified diagram of the oscillator system is shown in of devices has the following features: Figure9-1. • A total of five external and internal oscillator options as clock sources, providing 11 different clock modes. • On-chip 4x Phase Locked Loop (PLL) to boost internal operating frequency on select internal and external oscillator sources. FIGURE 9-1: PIC24FV32KA304 FAMILY CLOCK DIAGRAM Primary Oscillator REFOCON<15:8> XT, HS, EC OSCO Reference Clock Generator XTPLL, HSPLL OSCI ECPLL,FRCPLL 4 x PLL REFO 8 MHz 8 MHz aler 4 MHz FRCDIV FRC c s Oscillator st o P Peripherals 500 kHz LPFRC CLKDIV<10:8> FRC Oscillator CLKO LPRC LPRC Oscillator 31 kHz (nominal) aler CPU c s st Secondary Oscillator o P SOSC SOSCO CLKDIV<14:12> SOSCEN Enable SOSCI Oscillator Clock Control Logic Fail-Safe Clock Monitor WDT, PWRT, DSWDT Clock Source Option for Other Modules  2011-2017 Microchip Technology Inc. DS30009995E-page 115

PIC24FV32KA304 FAMILY 9.1 CPU Clocking Scheme 9.2 Initial Configuration on POR The system clock source can be provided by one of The oscillator source (and operating mode) that is used four sources: at a device Power-on Reset (POR) event is selected using Configuration bit settings. The Oscillator Configu- • Primary Oscillator (POSC) on the OSCI and ration bit settings are located in the Configuration OSCO pins registers in the program memory (for more information, • Secondary Oscillator (SOSC) on the SOSCI and see Section26.1 “Configuration Bits”). The Primary SOSCO pins Oscillator Configuration bits, POSCMD<1:0> The PIC24FV32KA304 family devices consist of (FOSC<1:0>), and the Initial Oscillator Select Configura- two types of secondary oscillator: tion bits, FNOSC<2:0> (FOSCSEL<2:0>), select the - High-Power Secondary Oscillator oscillator source that is used at a POR. The FRC Primary - Low-Power Secondary Oscillator Oscillator with Postscaler (FRCDIV) is the default (unpro- These can be selected by using the SOSCSEL grammed) selection. The secondary oscillator, or one of (FOSC<5>) bit. the internal oscillators, may be chosen by programming • Fast Internal RC (FRC) Oscillator these bit locations. The EC mode Frequency Range - 8 MHz FRC Oscillator Configuration bits, POSCFREQ<1:0> (FOSC<4:3>), - 500 kHz Lower Power FRC Oscillator optimize power consumption when running in EC mode. • Low-Power Internal RC (LPRC) Oscillator with The default configuration is “frequency range is greater two modes: than 8MHz”. - High-Power/High Accuracy mode The Configuration bits allow users to choose between - Low-Power/Low Accuracy mode the various clock modes, shown in Table9-1. The primary oscillator and 8 MHz FRC sources have the 9.2.1 CLOCK SWITCHING MODE option of using the internal 4x PLL. The frequency of the CONFIGURATION BITS FRC clock source can optionally be reduced by the pro- grammable clock divider. The selected clock source The FCKSMx Configuration bits (FOSC<7:6>) are generates the processor and peripheral clock sources. used jointly to configure device clock switching and the FSCM. Clock switching is enabled only when FCKSM1 The processor clock source is divided by two to produce is programmed (‘0’). The FSCM is enabled only when the internal instruction cycle clock, FCY. In this FCKSM<1:0> are both programmed (‘00’). document, the instruction cycle clock is also denoted by FOSC/2. The internal instruction cycle clock, FOSC/2, can be provided on the OSCO I/O pin for some operating modes of the primary oscillator. TABLE 9-1: CONFIGURATION BIT VALUES FOR CLOCK SELECTION Oscillator Mode Oscillator Source POSCMD<1:0> FNOSC<2:0> Notes 8 MHz FRC Oscillator with Postscaler Internal 11 111 1, 2 (FRCDIV) 500 kHz FRC Oscillator with Postscaler Internal 11 110 1 (LPFRCDIV) Low-Power RC Oscillator (LPRC) Internal 11 101 1 Secondary (Timer1) Oscillator (SOSC) Secondary 00 100 1 Primary Oscillator (HS) with PLL Module Primary 10 011 (HSPLL) Primary Oscillator (EC) with PLL Module Primary 00 011 (ECPLL) Primary Oscillator (HS) Primary 10 010 Primary Oscillator (XT) Primary 01 010 Primary Oscillator (EC) Primary 00 010 8 MHz FRC Oscillator with PLL Module Internal 11 001 1 (FRCPLL) 8 MHz FRC Oscillator (FRC) Internal 11 000 1 Note 1: The OSCO pin function is determined by the OSCIOFNC Configuration bit. 2: This is the default oscillator mode for an unprogrammed (erased) device. DS30009995E-page 116  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 9.3 Control Registers The Clock Divider register (Register9-2) controls the features associated with Doze mode, as well as the The operation of the oscillator is controlled by three postscaler for the FRC oscillator. Special Function Registers (SFRs): The FRC Oscillator Tune register (Register9-3) allows • OSCCON the user to fine tune the FRC oscillator over a range of • CLKDIV approximately ±5.25%. Each bit increment or decre- • OSCTUN ment changes the factory calibrated frequency of the FRC oscillator by a fixed amount. The OSCCON register (Register9-1) is the main control register for the oscillator. It controls clock source switching and allows the monitoring of clock sources. REGISTER 9-1: OSCCON: OSCILLATOR CONTROL REGISTER U-0 R-0, HSC R-0, HSC R-0, HSC U-0 R/W-x(1) R/W-x(1) R/W-x(1) — COSC2 COSC1 COSC0 — NOSC2 NOSC1 NOSC0 bit 15 bit 8 R/SO-0, HSC U-0 R-0, HSC(2) U-0 R/CO-0, HS R/W-0(3) R/W-0 R/W-0 CLKLOCK — LOCK — CF SOSCDRV SOSCEN OSWEN bit 7 bit 0 Legend: HSC = Hardware Settable/Clearable bit HS = Hardware Settable bit CO = Clearable Only bit SO = Settable Only bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 Unimplemented: Read as ‘0’ bit 14-12 COSC<2:0>: Current Oscillator Selection bits 111 = 8 MHz Fast RC Oscillator with Postscaler (FRCDIV) 110 = 500 kHz Low-Power Fast RC Oscillator (FRC) with Postscaler (LPFRCDIV) 101 = Low-Power RC Oscillator (LPRC) 100 = Secondary Oscillator (SOSC) 011 = Primary Oscillator with PLL module (XTPLL, HSPLL, ECPLL) 010 = Primary Oscillator (XT, HS, EC) 001 = 8 MHz FRC Oscillator with Postscaler and PLL module (FRCPLL) 000 = 8 MHz FRC Oscillator (FRC) bit 11 Unimplemented: Read as ‘0’ bit 10-8 NOSC<2:0>: New Oscillator Selection bits(1) 111 = 8 MHz Fast RC Oscillator with Postscaler (FRCDIV) 110 = 500 kHz Low-Power Fast RC Oscillator (FRC) with Postscaler (LPFRCDIV) 101 = Low-Power RC Oscillator (LPRC) 100 = Secondary Oscillator (SOSC) 011 = Primary Oscillator with PLL module (XTPLL, HSPLL, ECPLL) 010 = Primary Oscillator (XT, HS, EC) 001 = 8 MHz FRC Oscillator with Postscaler and PLL module (FRCPLL) 000 = 8 MHz FRC Oscillator (FRC) Note 1: Reset values for these bits are determined by the FNOSCx Configuration bits. 2: This bit also resets to ‘0’ during any valid clock switch or whenever a non-PLL Clock mode is selected. 3: When SOSC is selected to run from a digital clock input, rather than an external crystal (SOSCSRC=0), this bit has no effect.  2011-2017 Microchip Technology Inc. DS30009995E-page 117

PIC24FV32KA304 FAMILY REGISTER 9-1: OSCCON: OSCILLATOR CONTROL REGISTER (CONTINUED) bit 7 CLKLOCK: Clock Selection Lock Enabled bit If FSCM is enabled (FCKSM1 = 1): 1 = Clock and PLL selections are locked 0 = Clock and PLL selections are not locked and may be modified by setting the OSWEN bit If FSCM is disabled (FCKSM1 = 0): Clock and PLL selections are never locked and may be modified by setting the OSWEN bit. bit 6 Unimplemented: Read as ‘0’ bit 5 LOCK: PLL Lock Status bit(2) 1 = PLL module is in lock or PLL module start-up timer is satisfied 0 = PLL module is out of lock, PLL start-up timer is running or PLL is disabled bit 4 Unimplemented: Read as ‘0’ bit 3 CF: Clock Fail Detect bit 1 = FSCM has detected a clock failure 0 = No clock failure has been detected bit 2 SOSCDRV: Secondary Oscillator Drive Strength bit(3) 1 = High-power SOSC circuit is selected 0 = Low/high-power select is done via the SOSCSRC Configuration bit bit 1 SOSCEN: 32kHz Secondary Oscillator (SOSC) Enable bit 1 = Enables the secondary oscillator 0 = Disables the secondary oscillator bit 0 OSWEN: Oscillator Switch Enable bit 1 = Initiates an oscillator switch to the clock source specified by the NOSC<2:0> bits 0 = Oscillator switch is complete Note 1: Reset values for these bits are determined by the FNOSCx Configuration bits. 2: This bit also resets to ‘0’ during any valid clock switch or whenever a non-PLL Clock mode is selected. 3: When SOSC is selected to run from a digital clock input, rather than an external crystal (SOSCSRC=0), this bit has no effect. DS30009995E-page 118  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 9-2: CLKDIV: CLOCK DIVIDER REGISTER R/W-0 R/W-0 R/W-1 R/W-1 R/W-0 R/W-0 R/W-0 R/W-1 ROI DOZE2 DOZE1 DOZE0 DOZEN(1) RCDIV2 RCDIV1 RCDIV0 bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 ROI: Recover on Interrupt bit 1 = Interrupts clear the DOZEN bit, and reset the CPU and peripheral clock ratio to 1:1 0 = Interrupts have no effect on the DOZEN bit bit 14-12 DOZE<2:0>: CPU and Peripheral Clock Ratio Select bits 111 = 1:128 110 = 1:64 101 = 1:32 100 = 1:16 011 = 1:8 010 = 1:4 001 = 1:2 000 = 1:1 bit 11 DOZEN: Doze Enable bit(1) 1 = DOZE<2:0> bits specify the CPU and peripheral clock ratio 0 = CPU and peripheral clock ratio are set to 1:1 bit 10-8 RCDIV<2:0>: FRC Postscaler Select bits When COSC<2:0> (OSCCON<14:12>) = 111: 111 = 31.25 kHz (divide-by-256) 110 = 125 kHz (divide-by-64) 101 = 250 kHz (divide-by-32) 100 = 500 kHz (divide-by-16) 011 = 1 MHz (divide-by-8) 010 = 2 MHz (divide-by-4) 001 = 4 MHz (divide-by-2) (default) 000 = 8 MHz (divide-by-1) When COSC<2:0> (OSCCON<14:12>) = 110: 111 = 1.95 kHz (divide-by-256) 110 = 7.81 kHz (divide-by-64) 101 = 15.62 kHz (divide-by-32) 100 = 31.25 kHz (divide-by-16) 011 = 62.5 kHz (divide-by-8) 010 = 125 kHz (divide-by-4) 001 = 250 kHz (divide-by-2) (default) 000 = 500 kHz (divide-by-1) bit 7-0 Unimplemented: Read as ‘0’ Note 1: This bit is automatically cleared when the ROI bit is set and an interrupt occurs.  2011-2017 Microchip Technology Inc. DS30009995E-page 119

PIC24FV32KA304 FAMILY REGISTER 9-3: OSCTUN: FRC OSCILLATOR TUNE REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — TUN<5:0>(1) bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-6 Unimplemented: Read as ‘0’ bit 5-0 TUN<5:0>: FRC Oscillator Tuning bits(1) 011111 = Maximum frequency deviation 011110 • • • 000001 000000 = Center frequency, oscillator is running at factory calibrated frequency 111111 • • • 100001 100000 = Minimum frequency deviation Note 1: Increments or decrements of TUN<5:0> may not change the FRC frequency in equal steps over the FRC tuning range and may not be monotonic. DS30009995E-page 120  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 9.4 Clock Switching Operation Once the basic sequence is completed, the system clock hardware responds automatically, as follows: With few limitations, applications are free to switch 1. The clock switching hardware compares the between any of the four clock sources (POSC, SOSC, COSCx bits with the new value of the NOSCx FRC and LPRC) under software control and at any bits. If they are the same, then the clock switch time. To limit the possible side effects that could result is a redundant operation. In this case, the from this flexibility, PIC24F devices have a safeguard OSWEN bit is cleared automatically and the lock built into the switching process. clock switch is aborted. Note: The Primary Oscillator mode has three 2. If a valid clock switch has been initiated, the different submodes (XT, HS and EC), LOCK (OSCCON<5>) and CF (OSCCON<3>) which are determined by the POSCMDx bits are cleared. Configuration bits. While an application 3. The new oscillator is turned on by the hardware can switch to and from Primary Oscillator if it is not currently running. If a crystal oscillator mode in software, it cannot switch must be turned on, the hardware will wait until between the different primary submodes the OST expires. If the new source is using the without reprogramming the device. PLL, then the hardware waits until a PLL lock is detected (LOCK = 1). 9.4.1 ENABLING CLOCK SWITCHING 4. The hardware waits for 10 clock cycles from the To enable clock switching, the FCKSM1 Configuration bit new clock source and then performs the clock in the FOSC Configuration register must be programmed switch. to ‘0’. (Refer to Section26.0 “Special Features” for 5. The hardware clears the OSWEN bit to indicate a further details.) If the FCKSM1 Configuration bit is successful clock transition. In addition, the unprogrammed (‘1’), the clock switching function and NOSCx bits value is transferred to the COSCx FSCM function are disabled. This is the default setting. bits. The NOSCx control bits (OSCCON<10:8>) do not 6. The old clock source is turned off at this time, control the clock selection when clock switching is with the exception of LPRC (if WDT, FSCM or disabled. However, the COSCx bits (OSCCON<14:12>) RTCC with LPRC as a clock source is enabled) will reflect the clock source selected by the FNOSCx or SOSC (if SOSCEN remains enabled). Configuration bits. Note1: The processor will continue to execute The OSWEN control bit (OSCCON<0>) has no effect code throughout the clock switching when clock switching is disabled; it is held at ‘0’ at all sequence. Timing-sensitive code should times. not be executed during this time. 9.4.2 OSCILLATOR SWITCHING 2: Direct clock switches between any SEQUENCE Primary Oscillator mode with PLL and FRCPLL mode are not permitted. This At a minimum, performing a clock switch requires this applies to clock switches in either direc- basic sequence: tion. In these instances, the application 1. If desired, read the COSCx bits must switch to FRC mode as a transition (OSCCON<14:12>) to determine the current clock source between the two PLL oscillator source. modes. 2. Perform the unlock sequence to allow a write to the OSCCON register high byte. 3. Write the appropriate value to the NOSCx bits (OSCCON<10:8>) for the new oscillator source. 4. Perform the unlock sequence to allow a write to the OSCCON register low byte. 5. Set the OSWEN bit to initiate the oscillator switch.  2011-2017 Microchip Technology Inc. DS30009995E-page 121

PIC24FV32KA304 FAMILY The following code sequence for a clock switch is 9.5 Reference Clock Output recommended: In addition to the CLKO output (FOSC/2) available in 1. Disable interrupts during the OSCCON register certain oscillator modes, the device clock in the unlock and write sequence. PIC24FV32KA304 family devices can also be 2. Execute the unlock sequence for the OSCCON configured to provide a reference clock output signal to high byte by writing 78h and 9Ah to a port pin. This feature is available in all oscillator OSCCON<15:8>, in two back-to-back configurations and allows the user to select a greater instructions. range of clock submultiples to drive external devices in 3. Write new oscillator source to the NOSCx bits in the application. the instruction immediately following the unlock This reference clock output is controlled by the sequence. REFOCON register (Register9-4). Setting the ROEN 4. Execute the unlock sequence for the OSCCON bit (REFOCON<15>) makes the clock signal available low byte by writing 46h and 57h to on the REFO pin. The RODIVx bits (REFOCON<11:8>) OSCCON<7:0>, in two back-to-back instructions. enable the selection of 16 different clock divider 5. Set the OSWEN bit in the instruction immediately options. following the unlock sequence. The ROSSLP and ROSEL bits (REFOCON<13:12>) 6. Continue to execute code that is not control the availability of the reference output during clock-sensitive (optional). Sleep mode. The ROSEL bit determines if the oscillator 7. Invoke an appropriate amount of software delay on OSC1 and OSC2, or the current system clock (cycle counting) to allow the selected oscillator source, is used for the reference clock output. The and/or PLL to start and stabilize. ROSSLP bit determines if the reference source is 8. Check to see if OSWEN is ‘0’. If it is, the switch available on REFO when the device is in Sleep mode. was successful. If OSWEN is still set, then check To use the reference clock output in Sleep mode, both the LOCK bit to determine the cause of failure. the ROSSLP and ROSEL bits must be set. The device The core sequence for unlocking the OSCCON register clock must also be configured for one of the primary and initiating a clock switch is shown in Example9-1. modes (EC, HS or XT); otherwise, if the ROSEL bit is not also set, the oscillator on OSC1 and OSC2 will be EXAMPLE 9-1: BASIC CODE SEQUENCE powered down when the device enters Sleep mode. Clearing the ROSEL bit allows the reference output FOR CLOCK SWITCHING frequency to change as the system clock changes ;Place the new oscillator selection in W0 during any clock switches. ;OSCCONH (high byte) Unlock Sequence MOV #OSCCONH, w1 MOV #0x78, w2 MOV #0x9A, w3 MOV.b w2, [w1] MOV.b w3, [w1] ;Set new oscillator selection MOV.b WREG, OSCCONH ;OSCCONL (low byte) unlock sequence MOV #OSCCONL, w1 MOV #0x46, w2 MOV #0x57, w3 MOV.b w2, [w1] MOV.b w3, [w1] ;Start oscillator switch operation BSET OSCCON,#0 DS30009995E-page 122  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 9-4: REFOCON: REFERENCE OSCILLATOR CONTROL REGISTER R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ROEN — ROSSLP ROSEL RODIV3 RODIV2 RODIV1 RODIV0 bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 ROEN: Reference Oscillator Output Enable bit 1 = Reference oscillator is enabled on REFO pin 0 = Reference oscillator is disabled bit 14 Unimplemented: Read as ‘0’ bit 13 ROSSLP: Reference Oscillator Output Stop in Sleep bit 1 = Reference oscillator continues to run in Sleep 0 = Reference oscillator is disabled in Sleep bit 12 ROSEL: Reference Oscillator Source Select bit 1 = Primary oscillator is used as the base clock(1) 0 = System clock is used as the base clock; base clock reflects any clock switching of the device bit 11-8 RODIV<3:0>: Reference Oscillator Divisor Select bits 1111 = Base clock value divided by 32,768 1110 = Base clock value divided by 16,384 1101 = Base clock value divided by 8,192 1100 = Base clock value divided by 4,096 1011 = Base clock value divided by 2,048 1010 = Base clock value divided by 1,024 1001 = Base clock value divided by 512 1000 = Base clock value divided by 256 0111 = Base clock value divided by 128 0110 = Base clock value divided by 64 0101 = Base clock value divided by 32 0100 = Base clock value divided by 16 0011 = Base clock value divided by 8 0010 = Base clock value divided by 4 0001 = Base clock value divided by 2 0000 = Base clock value bit 7-0 Unimplemented: Read as ‘0’ Note 1: The crystal oscillator must be enabled using the FOSC<2:0> bits; the crystal maintains the operation in Sleep mode.  2011-2017 Microchip Technology Inc. DS30009995E-page 123

PIC24FV32KA304 FAMILY NOTES: DS30009995E-page 124  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 10.0 POWER-SAVING FEATURES The assembly syntax of the PWRSAV instruction is shown in Example10-1. Note: This data sheet summarizes the features Note: SLEEP_MODE and IDLE_MODE are of this group of PIC24F devices. It is not constants defined in the assembler intended to be a comprehensive refer- include file for the selected device. ence source. For more information, refer to the “dsPIC33/PIC24 Family Reference Sleep and Idle modes can be exited as a result of an Manual”, ”Power-Saving Features with enabled interrupt, WDT time-out or a device Reset. Deep Sleep” (DS39727). When the device exits these modes, it is said to “wake-up”. The PIC24FV32KA304 family of devices provides the ability to manage power consumption by selectively 10.2.1 SLEEP MODE managing clocking to the CPU and the peripherals. In Sleep mode includes these features: general, a lower clock frequency and a reduction in the number of circuits being clocked constitutes lower • The system clock source is shut down. If an consumed power. All PIC24F devices manage power on-chip oscillator is used, it is turned off. consumption in four different ways: • The device current consumption will be reduced • Clock Frequency to a minimum provided that no I/O pin is sourcing current. • Instruction-Based Sleep, Idle and Deep Sleep modes • The I/O pin directions and states are frozen. • Software Controlled Doze mode • The Fail-Safe Clock Monitor does not operate during Sleep mode since the system clock source • Selective Peripheral Control in Software is disabled. Combinations of these methods can be used to • The LPRC clock will continue to run in Sleep selectively tailor an application’s power consumption, mode if the WDT or RTCC with LPRC as the clock while still maintaining critical application features, such source is enabled. as timing-sensitive communications. • The WDT, if enabled, is automatically cleared prior to entering Sleep mode. 10.1 Clock Frequency and Clock • Some device features or peripherals may Switching continue to operate in Sleep mode. This includes PIC24F devices allow for a wide range of clock items, such as the Input Change Notification on frequencies to be selected under application control. If the I/O ports, or peripherals that use an external the system clock configuration is not locked, users can clock input. Any peripheral that requires the choose low-power or high-precision oscillators by simply system clock source for its operation will be changing the NOSCx bits. The process of changing a disabled in Sleep mode. system clock during operation, as well as limitations to The device will wake-up from Sleep mode on any of the process, are discussed in more detail in Section9.0 these events: “Oscillator Configuration”. • On any interrupt source that is individually enabled 10.2 Instruction-Based Power-Saving • On any form of device Reset Modes • On a WDT time-out PIC24F devices have two special power-saving modes On wake-up from Sleep, the processor will restart with that are entered through the execution of a special the same clock source that was active when Sleep PWRSAV instruction. Sleep mode stops clock operation mode was entered. and halts all code execution; Idle mode halts the CPU and code execution, but allows peripheral modules to continue operation. Deep Sleep mode stops clock operation, code execution and all peripherals, except RTCC and DSWDT. It also freezes I/O states and removes power to SRAM and Flash memory. EXAMPLE 10-1: PWRSAV INSTRUCTION SYNTAX PWRSAV #SLEEP_MODE ; Put the device into SLEEP mode PWRSAV #IDLE_MODE ; Put the device into IDLE mode BSET DSCON, #DSEN ; Enable Deep Sleep PWRSAV #SLEEP_MODE ; Put the device into Deep SLEEP mode  2011-2017 Microchip Technology Inc. DS30009995E-page 125

PIC24FV32KA304 FAMILY 10.2.2 IDLE MODE 10.2.4.1 Entering Deep Sleep Mode Idle mode has these features: Deep Sleep mode is entered by setting the DSEN bit in • The CPU will stop executing instructions. the DSCON register and then executing a Sleep com- mand (PWRSAV #SLEEP_MODE). An unlock sequence • The WDT is automatically cleared. is required to set the DSEN bit. Once the DSEN bit has • The system clock source remains active. By been set, there is no time limit before the SLEEP com- default, all peripheral modules continue to operate mand can be executed. The DSEN bit is automatically normally from the system clock source, but can cleared when exiting the Deep Sleep mode. also be selectively disabled (see Section10.6 “Selective Peripheral Module Control”). Note: To re-enter Deep Sleep after a Deep Sleep • If the WDT or FSCM is enabled, the LPRC will wake-up, allow a delay of at least 3 TCY also remain active. after clearing the RELEASE bit. The device will wake from Idle mode on any of these The sequence to enter Deep Sleep mode is: events: 1. If the application requires the Deep Sleep WDT, • Any interrupt that is individually enabled enable it and configure its clock source. For • Any device Reset more information on Deep Sleep WDT, see • A WDT time-out Section10.2.4.5 “Deep Sleep WDT”. On wake-up from Idle, the clock is re-applied to the 2. If the application requires Deep Sleep BOR, CPU and instruction execution begins immediately, enable it by programming the DSLPBOR starting with the instruction following the PWRSAV Configuration bit (FDS<6>). instruction or the first instruction in the ISR. 3. If the application requires wake-up from Deep Sleep on RTCC alarm, enable and configure the 10.2.3 INTERRUPTS COINCIDENT WITH RTCC module For more information on RTCC, POWER SAVE INSTRUCTIONS see Section19.0 “Real-Time Clock and Any interrupt that coincides with the execution of a Calendar (RTCC)”. PWRSAV instruction will be held off until entry into Sleep 4. If needed, save any critical application context or Idle mode has completed. The device will then data by writing it to the DSGPR0 and DSGPR1 wake-up from Sleep or Idle mode. registers (optional). 5. Enable Deep Sleep mode by setting the DSEN 10.2.4 DEEP SLEEP MODE bit (DSCON<15>). In PIC24FV32KA304 family devices, Deep Sleep mode Note: An unlock sequence is required to set the is intended to provide the lowest levels of power DSEN bit. consumption available without requiring the use of external switches to completely remove all power from 6. Enter Deep Sleep mode by issuing a PWRSAV#0 the device. Entry into Deep Sleep mode is completely instruction. under software control. Exit from Deep Sleep mode can Any time the DSEN bit is set, all bits in the DSWAKE be triggered from any of the following events: register will be automatically cleared. • POR Event To set the DSEN bit, the unlock sequence in • MCLR Event Example10-2 is required: • RTCC Alarm (if the RTCC is present) • External Interrupt 0 EXAMPLE 10-2: THE UNLOCK SEQUENCE • Deep Sleep Watchdog Timer (DSWDT) Time-out //Disable Interrupts For 5 instructions • Ultra Low-Power Wake-up (ULPWU) Event asm volatile(“disi #5”); //Issue Unlock Sequence In Deep Sleep mode, it is possible to keep the device asm volatile Real-Time Clock and Calendar (RTCC) running without mov #0x55, W0; the loss of clock cycles. mov W0, NVMKEY; The device has a dedicated Deep Sleep Brown-out mov #0xAA, W1; Reset (DSBOR) and a Deep Sleep Watchdog Timer mov W1, NVMKEY; Reset (DSWDT) for monitoring voltage and time-out bset DSCON, #DSEN events. The DSBOR and DSWDT are independent of the standard BOR and WDT used with other power-managed modes (Sleep, Idle and Doze). DS30009995E-page 126  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 10.2.4.2 Exiting Deep Sleep Mode Applications which require critical data to be saved prior to Deep Sleep may use the Deep Sleep General Deep Sleep mode exits on any one of the following events: Purpose registers, DSGPR0 and DSGPR1 or data • A POR event on VDD supply. If there is no EEPROM (if available). Unlike other SFRs, the con- DSBOR circuit to re-arm the VDD supply POR cir- tents of these registers are preserved while the device cuit, the external VDD supply must be lowered to is in Deep Sleep mode. After exiting Deep Sleep, soft- the natural arming voltage of the POR circuit. ware can restore the data by reading the registers and • A DSWDT time-out. When the DSWDT timer clearing the RELEASE bit (DSCON<0>). times out, the device exits Deep Sleep. 10.2.4.4 I/O Pins During Deep Sleep • An RTCC alarm (if RTCEN = 1). • An assertion (‘0’) of the MCLR pin. During Deep Sleep, the general purpose I/O pins retain their previous states and the Secondary Oscillator • An assertion of the INT0 pin (if the interrupt was enabled before Deep Sleep mode was entered). (SOSC) will remain running, if enabled. Pins that are The polarity configuration is used to determine the configured as inputs (TRISx bit is set), prior to entry into Deep Sleep, remain high-impedance during Deep assertion level (‘0’ or ‘1’) of the pin that will cause an exit from Deep Sleep mode. Exiting from Deep Sleep. Pins that are configured as outputs (TRISx bit is Sleep mode requires a change on the INT0 pin clear), prior to entry into Deep Sleep, remain as output while in Deep Sleep mode. pins during Deep Sleep. While in this mode, they continue to drive the output level determined by their Note: Any interrupt pending when entering corresponding LATx bit at the time of entry into Deep Deep Sleep mode is cleared. Sleep. Exiting Deep Sleep mode generally does not retain the Once the device wakes back up, all I/O pins continue to state of the device and is equivalent to a Power-on maintain their previous states, even after the device Reset (POR) of the device. Exceptions to this include has finished the POR sequence and is executing the RTCC (if present), which remains operational application code again. Pins configured as inputs through the wake-up, the DSGPRx registers and during Deep Sleep remain high-impedance and pins DSWDT. configured as outputs continue to drive their previous Wake-up events that occur after Deep Sleep exits, but value. After waking up, the TRIS and LAT registers, and before the POR sequence completes, are ignored and the SOSCEN bit (OSCCON<1>) are reset. If firmware are not be captured in the DSWAKE register. modifies any of these bits or registers, the I/O will not immediately go to the newly configured states. Once The sequence for exiting Deep Sleep mode is: the firmware clears the RELEASE bit (DSCON<0>), 1. After a wake-up event, the device exits Deep the I/O pins are “released”. This causes the I/O pins to Sleep and performs a POR. The DSEN bit is take the states configured by their respective TRISx cleared automatically. Code execution resumes and LATx bit values. at the Reset vector. This means that keeping the SOSC running after 2. To determine if the device exited Deep Sleep, waking up requires the SOSCEN bit to be set before read the Deep Sleep bit, DPSLP (RCON<10>). clearing RELEASE. This bit will be set if there was an exit from Deep If the Deep Sleep BOR (DSBOR) is enabled, and a Sleep mode; if the bit is set, clear it. DSBOR or a true POR event occurs during Deep 3. Determine the wake-up source by reading the Sleep, the I/O pins will be immediately released, similar DSWAKE register. to clearing the RELEASE bit. All previous state 4. Determine if a DSBOR event occurred during information will be lost, including the general purpose Deep Sleep mode by reading the DSBOR bit DSGPR0 and DSGPR1 contents. (DSCON<1>). If a MCLR Reset event occurs during Deep Sleep, the 5. If application context data has been saved, read DSGPRx, DSCON and DSWAKE registers will remain it back from the DSGPR0 and DSGPR1 registers. valid, and the RELEASE bit will remain set. The state 6. Clear the RELEASE bit (DSCON<0>). of the SOSC will also be retained. The I/O pins, however, will be reset to their MCLR Reset state. Since 10.2.4.3 Saving Context Data with the RELEASE is still set, changes to the SOSCEN bit DSGPR0/DSGPR1 Registers (OSCCON<1>) cannot take effect until the RELEASE As exiting Deep Sleep mode causes a POR, most bit is cleared. Special Function Registers reset to their default POR In all other Deep Sleep wake-up cases, application values. In addition, because VCORE power is not sup- firmware must clear the RELEASE bit in order to plied in Deep Sleep mode, information in data RAM reconfigure the I/O pins. may be lost when exiting this mode.  2011-2017 Microchip Technology Inc. DS30009995E-page 127

PIC24FV32KA304 FAMILY 10.2.4.5 Deep Sleep WDT 10.2.4.8 Power-on Resets (PORs) To enable the DSWDT in Deep Sleep mode, program VDD voltage is monitored to produce PORs. Since the Configuration bit, DSWDTEN (FDS<7>). The exiting from Deep Sleep functionally looks like a POR, device Watchdog Timer (WDT) need not be enabled for the technique described in Section10.2.4.7 “Checking the DSWDT to function. Entry into Deep Sleep mode and Clearing the Status of Deep Sleep” should be automatically resets the DSWDT. used to distinguish between Deep Sleep and a true POR event. The DSWDT clock source is selected by the DSWDTOSC Configuration bit (FDS<4>). The posts- When a true POR occurs, the entire device, including caler options are programmed by the DSWDTPS<3:0> all Deep Sleep logic (Deep Sleep registers: RTCC, Configuration bits (FDS<3:0>). The minimum time-out DSWDT, etc.) is reset. period that can be achieved is 2.1 ms and the maximum is 25.7 days. For more details on the FDS Configuration 10.2.4.9 Summary of Deep Sleep Sequence register and DSWDT configuration options, refer to To review, these are the necessary steps involved in Section26.0 “Special Features”. invoking and exiting Deep Sleep mode: 10.2.4.6 Switching Clocks in Deep Sleep Mode 1. The device exits Reset and begins to execute its application code. Both the RTCC and the DSWDT may run from either 2. If DSWDT functionality is required, program the SOSC or the LPRC clock source. This allows both the appropriate Configuration bit. RTCC and DSWDT to run without requiring both the 3. Select the appropriate clock(s) for the DSWDT LPRC and SOSC to be enabled together, reducing and RTCC (optional). power consumption. 4. Enable and configure the DSWDT (optional). Running the RTCC from LPRC will result in a loss of 5. Enable and configure the RTCC (optional). accuracy in the RTCC of approximately 5 to 10%. If a more accurate RTCC is required, it must be run from 6. Write context data to the DSGPRx registers the SOSC clock source. The RTCC clock source is (optional). selected with the RTCOSC Configuration bit (FDS<5>). 7. Enable the INT0 interrupt (optional). Under certain circumstances, it is possible for the 8. Set the DSEN bit in the DSCON register. DSWDT clock source to be off when entering Deep 9. Enter Deep Sleep by issuing a PWRSV Sleep mode. In this case, the clock source is turned on #SLEEP_MODE command. automatically (if DSWDT is enabled), without the need 10. The device exits Deep Sleep when a wake-up for software intervention; however, this can cause a event occurs. delay in the start of the DSWDT counters. In order to 11. The DSEN bit is automatically cleared. avoid this delay when using SOSC as a clock source, 12. Read and clear the DPSLP status bit in RCON, the application can activate SOSC prior to entering and the DSWAKE status bits. Deep Sleep mode. 13. Read the DSGPRx registers (optional). 10.2.4.7 Checking and Clearing the Status of 14. Once all state related configurations are Deep Sleep complete, clear the RELEASE bit. Upon entry into Deep Sleep mode, the status bit, 15. The application resumes normal operation. DPSLP (RCON<10>), becomes set and must be cleared by the software. On power-up, the software should read this status bit to determine if the Reset was due to an exit from Deep Sleep mode and clear the bit if it is set. Of the four possible combinations of DPSLP and POR bit states, three cases can be considered: • Both the DPSLP and POR bits are cleared. In this case, the Reset was due to some event other than a Deep Sleep mode exit. • The DPSLP bit is clear, but the POR bit is set; this is a normal POR. • Both the DPSLP and POR bits are set. This means that Deep Sleep mode was entered, the device was powered down and Deep Sleep mode was exited. DS30009995E-page 128  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 10-1: DSCON: DEEP SLEEP CONTROL REGISTER(1) R/W-0 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 DSEN — — — — — — RTCCWDIS bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 R/C-0, HS — — — — — ULPWUDIS DSBOR(2) RELEASE bit 7 bit 0 Legend: C = Clearable bit HS = Hardware Settable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 DSEN: Deep Sleep Enable bit 1 = Enters Deep Sleep on execution of PWRSAV #0 0 = Enters normal Sleep on execution of PWRSAV #0 bit 14-9 Unimplemented: Read as ‘0’ bit 8 RTCCWDIS: RTCC Wake-up Disable bit 1 = Wake-up from Deep Sleep with RTCC disabled 0 = Wake-up from Deep Sleep with RTCC enabled bit 7-3 Unimplemented: Read as ‘0’ bit 2 ULPWUDIS: ULPWU Wake-up Disable bit 1 = Wake-up from Deep Sleep with ULPWU disabled 0 = Wake-up from Deep Sleep with ULPWU enabled bit 1 DSBOR: Deep Sleep BOR Event bit(2) 1 = The DSBOR was active and a BOR event was detected during Deep Sleep 0 = The DSBOR was not active or was active but did not detect a BOR event during Deep Sleep bit 0 RELEASE: I/O Pin State Release bit 1 = Upon waking from Deep Sleep, I/O pins maintain their previous states to Deep Sleep entry 0 = Release I/O pins from their state previous to Deep Sleep entry, and allow their respective TRISx and LATx bits to control their states Note 1: All register bits are only reset in the case of a POR event outside of Deep Sleep mode. 2: Unlike all other events, a Deep Sleep BOR event will NOT cause a wake-up from Deep Sleep; this re-arms POR.  2011-2017 Microchip Technology Inc. DS30009995E-page 129

PIC24FV32KA304 FAMILY REGISTER 10-2: DSWAKE: DEEP SLEEP WAKE-UP SOURCE REGISTER(1) U-0 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0, HS — — — — — — — DSINT0 bit 15 bit 8 R/W-0, HS U-0 U-0 R/W-0, HS R/W-0, HS R/W-0, HS U-0 R/W-0, HS DSFLT — — DSWDT DSRTCC DSMCLR — DSPOR(2,3) bit 7 bit 0 Legend: HS = Hardware Settable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-9 Unimplemented: Read as ‘0’ bit 8 DSINT0: Deep Sleep Interrupt-on-Change bit 1 = Interrupt-on-change was asserted during Deep Sleep 0 = Interrupt-on-change was not asserted during Deep Sleep bit 7 DSFLT: Deep Sleep Fault Detect bit 1 = A Fault occurred during Deep Sleep and some Deep Sleep configuration settings may have been corrupted 0 = No Fault was detected during Deep Sleep bit 6-5 Unimplemented: Read as ‘0’ bit 4 DSWDT: Deep Sleep Watchdog Timer Time-out bit 1 = The Deep Sleep Watchdog Timer timed out during Deep Sleep 0 = The Deep Sleep Watchdog Timer did not time out during Deep Sleep bit 3 DSRTCC: Deep Sleep Real-Time Clock and Calendar (RTCC) Alarm bit 1 = The Real-Time Clock and Calendar triggered an alarm during Deep Sleep 0 = The Real-Time Clock and Calendar did not trigger an alarm during Deep Sleep bit 2 DSMCLR: Deep Sleep MCLR Event bit 1 = The MCLR pin was active and was asserted during Deep Sleep 0 = The MCLR pin was not active, or was active, but not asserted during Deep Sleep bit 1 Unimplemented: Read as ‘0’ bit 0 DSPOR: Deep Sleep Power-on Reset Event bit(2,3) 1 = The VDD supply POR circuit was active and a POR event was detected 0 = The VDD supply POR circuit was not active, or was active, but did not detect a POR event Note 1: All register bits are cleared when the DSEN (DSCON<15>) bit is set. 2: All register bits are reset only in the case of a POR event outside of Deep Sleep mode, except bit, DSPOR, which does not reset on a POR event that is caused due to a Deep Sleep exit. 3: Unlike the other bits in this register, this bit can be set outside of Deep Sleep. DS30009995E-page 130  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 10.3 Ultra Low-Power Wake-up EXAMPLE 10-3: ULTRA LOW-POWER WAKE-UP INITIALIZATION The Ultra Low-Power Wake-up (ULPWU) on pin, RB0, //******************************* allows a slow falling voltage to generate an interrupt // 1. Charge the capacitor on RB0 without excess current consumption. //******************************* To use this feature: TRISBbits.TRISB0 = 0; LATBbits.LATB0 = 1; 1. Charge the capacitor on RB0 by configuring the for(i = 0; i < 10000; i++) Nop(); RB0 pin to an output and setting it to ‘1’. //***************************** 2. Stop charging the capacitor by configuring RB0 //2. Stop Charging the capacitor as an input. // on RB0 3. Discharge the capacitor by setting the ULPEN //***************************** TRISBbits.TRISB0 = 1; and ULPSINK bits in the ULPWCON register. //***************************** 4. Configure Sleep mode. //3. Enable ULPWU Interrupt 5. Enter Sleep mode. //***************************** IFS5bits.ULPWUIF = 0; When the voltage on RB0 drops below VIL, the device IEC5bits.ULPWUIE = 1; wakes up and executes the next instruction. IPC21bits.ULPWUIP = 0x7; This feature provides a low-power technique for //***************************** periodically waking up the device from Sleep mode. //4. Enable the Ultra Low Power // Wakeup module and allow The time-out is dependent on the discharge time of the // capacitor discharge RC circuit on RB0. //***************************** When the ULPWU module wakes the device from ULPWCONbits.ULPEN = 1; ULPWCONbit.ULPSINK = 1; Sleep mode, the ULPWUIF bit (IFS5<0>) is set. Soft- //***************************** ware can check this bit upon wake-up to determine the //5. Enter Sleep Mode wake-up source. See Example10-3 for initializing the //***************************** ULPWU module. Sleep(); A series resistor, between RB0 and the external //for sleep, execution will capacitor, provides overcurrent protection for the //resume here RB0/AN0/ULPWU pin and enables software calibration of the time-out (see Figure10-1). FIGURE 10-1: SERIES RESISTOR R 1 RB0 C 1 A timer can be used to measure the charge time and discharge time of the capacitor. The charge time can then be adjusted to provide the desired delay in Sleep. This technique compensates for the affects of tempera- ture, voltage and component accuracy. The peripheral can also be configured as a simple, programmable Low-Voltage Detect (LVD) or temperature sensor.  2011-2017 Microchip Technology Inc. DS30009995E-page 131

PIC24FV32KA304 FAMILY REGISTER 10-3: ULPWCON: ULPWU CONTROL REGISTER R/W-0 U-0 R/W-0 U-0 U-0 U-0 U-0 R/W-0 ULPEN — ULPSIDL — — — — ULPSINK bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 ULPEN: ULPWU Module Enable bit 1 = Module is enabled 0 = Module is disabled bit 14 Unimplemented: Read as ‘0’ bit 13 ULPSIDL: ULPWU Stop in Idle Select bit 1 = Discontinues module operation when the device enters Idle mode 0 = Continues module operation in Idle mode bit 12-9 Unimplemented: Read as ‘0’ bit 8 ULPSINK: ULPWU Current Sink Enable bit 1 = Current sink is enabled 0 = Current sink is disabled bit 7-0 Unimplemented: Read as ‘0’ DS30009995E-page 132  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 10.4 Voltage Regulator-Based 10.4.3 RETENTION SLEEP MODE Power-Saving Features In Retention Sleep mode, the device is in Sleep and all regulated voltage is provided solely by the Retention The PIC24FV32KA304 series devices have a Voltage Regulator. Consequently, this mode has lower power Regulator that has the ability to alter functionality to consumption than regular Sleep mode, but is also provide power savings. The on-board regulator is made limited in terms of how much functionality can be up of two basic modules: the Voltage Regulator enabled. Retention Sleep wake-up time is longer than (VREG) and the Retention Regulator (RETREG). With Sleep mode due to the extra time required to raise the the combination of VREG and RETREG, the following VCORE supply rail back to normal regulated levels. power modes are available: Note: PIC24F32KA30X family devices do not 10.4.1 RUN MODE use an On-Chip Voltage Regulator, so In Run mode, the main VREG is providing a regulated they do not support Retention Sleep voltage with enough current to supply a device running mode. at full speed, and the device is not in Sleep or Deep Sleep Mode. The Retention Regulator may or may not 10.4.4 DEEP SLEEP MODE be running, but is unused. In Deep Sleep mode, both the main Voltage Regulator and Retention Regulator are shut down, providing the 10.4.2 SLEEP (STANDBY) MODE lowest possible device power consumption. However, In Sleep mode, the device is in Sleep and the main this mode provides no retention or functionality of the VREG is providing a regulated voltage at a reduced device and has the longest wake-up time. (standby) supply current. This mode provides for limited functionality due to the reduced supply current. It requires a longer time to wake-up from Sleep. TABLE 10-1: VOLTAGE REGULATION CONFIGURATION SETTINGS FOR PIC24FV32KA304 FAMILY DEVICES RETCGF Bit RETEN Bit PMSLP Bit Power Mode Description (FPOR<2>) (RCON<12> (RCON<8>) During Sleep VREG mode (normal) is unchanged during Sleep. 0 0 1 Sleep RETREG is unused. Sleep VREG goes to Low-Power Standby mode during 0 0 0 (Standby) Sleep. RETREG is unused. Retention VREG is off during Sleep. RETREG is enabled and 0 1 0 Sleep provides Sleep voltage regulation. VREG mode (normal) is unchanged during Sleep. 1 X 1 Sleep RETREG is disabled at all times. Sleep VREG goes to Low-Power Standby mode during 1 X 0 (Standby) Sleep. RETREG is disabled at all times  2011-2017 Microchip Technology Inc. DS30009995E-page 133

PIC24FV32KA304 FAMILY 10.5 Doze Mode 10.6 Selective Peripheral Module Control Generally, changing clock speed and invoking one of the power-saving modes are the preferred strategies Idle and Doze modes allow users to substantially for reducing power consumption. There may be circum- reduce power consumption by slowing or stopping the stances, however, where this is not practical. For CPU clock. Even so, peripheral modules still remain example, it may be necessary for an application to clocked, and thus, consume power. There may be maintain uninterrupted synchronous communication, cases where the application needs what these modes even while it is doing nothing else. Reducing system do not provide: the allocation of power resources to clock speed may introduce communication errors, CPU processing, with minimal power consumption while using a power-saving mode may stop from the peripherals. communications completely. PIC24F devices address this requirement by allowing Doze mode is a simple and effective alternative method peripheral modules to be selectively disabled, reducing to reduce power consumption while the device is still or eliminating their power consumption. This can be executing code. In this mode, the system clock done with two control bits: continues to operate from the same source and at the • The Peripheral Enable bit, generically named, same speed. Peripheral modules continue to be “XXXEN”, located in the module’s main control clocked at the same speed, while the CPU clock speed SFR. is reduced. Synchronization between the two clock domains is maintained, allowing the peripherals to • The Peripheral Module Disable (PMD) bit, access the SFRs while the CPU executes code at a generically named, “XXXMD”, located in one of slower rate. the PMD Control registers. Doze mode is enabled by setting the DOZEN bit Both bits have similar functions in enabling or disabling its (CLKDIV<11>). The ratio between peripheral and core associated module. Setting the PMDx bits for a module disables all clock sources to that module, reducing its clock speed is determined by the DOZE<2:0> bits (CLKDIV<14:12>). There are eight possible power consumption to an absolute minimum. In this state, the control and status registers associated with the configurations, from 1:1 to 1:128, with 1:1 being the default. peripheral will also be disabled, so writes to those registers will have no effect, and read values will be It is also possible to use Doze mode to selectively reduce invalid. Many peripheral modules have a corresponding power consumption in event driven applications. This PMDx bit. allows clock-sensitive functions, such as synchronous In contrast, disabling a module by clearing its XXXEN communications, to continue without interruption. Mean- while, the CPU Idles, waiting for something to invoke an bit, disables its functionality, but leaves its registers available to be read and written to. Power consumption interrupt routine. Enabling the automatic return to full-speed CPU operation on interrupts is enabled by is reduced, but not by as much as the PMDx bits are used. Most peripheral modules have an enable bit; setting the ROI bit (CLKDIV<15>). By default, interrupt events have no effect on Doze mode operation. exceptions include capture, compare and RTCC. To achieve more selective power savings, peripheral modules can also be selectively disabled when the device enters Idle mode. This is done through the control bit of the generic name format, “XXXIDL”. By default, all modules that can operate during Idle mode will do so. Using the disable on Idle feature disables the module while in Idle mode, allowing further reduction of power consumption during Idle mode, enhancing power savings for extremely critical power applications. DS30009995E-page 134  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 11.0 I/O PORTS When a peripheral is enabled and the peripheral is actively driving an associated pin, the use of the pin as Note: This data sheet summarizes the features of a general purpose output pin is disabled. The I/O pin this group of PIC24F devices. It is not may be read, but the output driver for the parallel port intended to be a comprehensive reference bit will be disabled. If a peripheral is enabled, but the source. For more information on the I/O peripheral is not actively driving a pin, that pin may be Ports, refer to the “dsPIC33/PIC24 Family driven by a port. Reference Manual”, “I/O Ports with All port pins have three registers directly associated Peripheral Pin Select (PPS)” (DS39711). with their operation as digital I/O. The Data Direction Note that the PIC24FV32KA304 family register (TRISx) determines whether the pin is an input devices do not support Peripheral Pin or an output. If the data direction bit is a ‘1’, then the pin Select features. is an input. All port pins are defined as inputs after a Reset. Reads from the Data Latch register (LAT), read All of the device pins (except VDD and VSS) are shared the latch. Writes to the latch, write the latch. Reads between the peripherals and the parallel I/O ports. All from the port (PORT), read the port pins; writes to the I/O input ports feature Schmitt Trigger inputs for port pins, write the latch. improved noise immunity. Any bit and its associated data and control registers 11.1 Parallel I/O (PIO) Ports that are not valid for a particular device will be disabled. That means the corresponding LATx and A parallel I/O port that shares a pin with a peripheral is, TRISx registers, and the port pin will read as zeros. in general, subservient to the peripheral. The When a pin is shared with another peripheral or peripheral’s output buffer data and control signals are function that is defined as an input only, it is provided to a pair of multiplexers. The multiplexers nevertheless regarded as a dedicated port because select whether the peripheral or the associated port there is no other competing source of outputs. has ownership of the output data and control signals of the I/O pin. The logic also prevents “loop through”, in Note: The I/O pins retain their state during Deep which a port’s digital output can drive the input of a Sleep. They will retain this state at peripheral that shares the same pin. Figure11-1 wake-up until the software restore bit illustrates how ports are shared with other peripherals (RELEASE) is cleared. and the associated I/O pin to which they are connected. FIGURE 11-1: BLOCK DIAGRAM OF A TYPICAL SHARED PORT STRUCTURE Peripheral Module Output Multiplexers Peripheral Input Data Peripheral Module Enable I/O Peripheral Output Enable 1 Output Enable Peripheral Output Data 0 PIO Module 1 Output Data Read TRIS 0 Data Bus D Q I/O Pin WR TRIS CK TRIS Latch D Q WR LAT + CK WR PORT Data Latch Read LAT Input Data Read PORT  2011-2017 Microchip Technology Inc. DS30009995E-page 135

PIC24FV32KA304 FAMILY 11.1.1 OPEN-DRAIN CONFIGURATION When reading the PORT register, all pins configured as analog input channels will read as cleared (a low level). In addition to the PORT, LAT and TRIS registers for Analog levels on any pin that is defined as a digital data control, each port pin can also be individually input (including the ANx pins) may cause the input configured for either digital or open-drain output. This is buffer to consume current that exceeds the device controlled by the Open-Drain Control register, ODCx, specifications. associated with each port. Setting any of the bits configures the corresponding pin to act as an 11.2.1 ANALOG SELECTION REGISTERS open-drain output. I/O pins with shared analog functionality, such as A/D The maximum open-drain voltage allowed is the same inputs and comparator inputs, must have their digital as the maximum VIH specification. inputs shut off when analog functionality is used. Note that analog functionality includes an analog voltage 11.2 Configuring Analog Port Pins being applied to the pin externally. The use of the ANS and TRIS registers control the To allow for analog control, the ANSx registers are operation of the A/D port pins. The port pins that are provided. There is one ANS register for each port desired as analog inputs must have their correspond- (ANSA, ANSB and ANSC). Within each ANSx register, ing TRISx bit set (input). If the TRISx bit is cleared there is a bit for each pin that shares analog (output), the digital output level (VOH or VOL) will be functionality with the digital I/O functionality. converted. If a particular pin does not have an analog function, that bit is unimplemented. See Register11-1 to Register11-3 for implementation. REGISTER 11-1: ANSA: ANALOG SELECTION (PORTA) U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 U-0 U-0 R/W-1 R/W-1 R/W-1 R/W-1 — — — — ANSA<3:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-4 Unimplemented: Read as ‘0’ bit 3-0 ANSA<3:0>: Analog Select Control bits 1 = Digital input buffer is not active (use for analog input) 0 = Digital input buffer is active DS30009995E-page 136  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 11-2: ANSB: ANALOG SELECTION (PORTB) R/W-1 R/W-1 R/W-1 R/W-1 U-0 U-0 U-0 U-0 ANSB<15:12> — — — — bit 15 bit 8 U-0 U-0 U-0 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 — — — ANSB<4:0>(1) bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-12 ANSB<15:12>: Analog Select Control bits 1 = Digital input buffer is not active (use for analog input) 0 = Digital input buffer is active bit 11-5 Unimplemented: Read as ‘0’ bit 4-0 ANSB<4:0>: Analog Select Control bits(1) 1 = Digital input buffer is not active (use for analog input) 0 = Digital input buffer is active Note 1: The ANSB3 bit is not available on 20-pin devices. REGISTER 11-3: ANSC ANALOG SELECTION (PORTC) U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 R/W-1 R/W-1 R/W-1 — — — — — ANSC<2:0>(1) bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-3 Unimplemented: Read as ‘0’ bit 2-0 ANSC<2:0>: Analog Select Control bits(1) 1 = Digital input buffer is not active (use for analog input) 0 = Digital input buffer is active Note 1: These bits are not available on 20-pin or 28-pin devices.  2011-2017 Microchip Technology Inc. DS30009995E-page 137

PIC24FV32KA304 FAMILY 11.2.2 I/O PORT WRITE/READ TIMING On any pin, only the pull-up resistor or the pull-down resistor should be enabled, but not both of them. If the One instruction cycle is required between a port push button or the keypad is connected to VDD, enable direction change or port write operation and a read the pull-down, or if they are connected to VSS, enable operation of the same port. Typically, this instruction the pull-up resistors. The pull-ups are enabled would be a NOP. separately, using the CNPU1 and CNPU2 registers, which contain the control bits for each of the CN pins. 11.3 Input Change Notification (ICN) Setting any of the control bits enables the weak The Input Change Notification function of the I/O ports pull-ups for the corresponding pins. The pull-downs are allows the PIC24FV32KA304 family of devices to enabled separately, using the CNPD1 and CNPD2 reg- generate interrupt requests to the processor in isters, which contain the control bits for each of the CN response to a Change-of-State (COS) on selected pins. Setting any of the control bits enables the weak input pins. This feature is capable of detecting input pull-downs for the corresponding pins. Change-of-States, even in Sleep mode, when the When the internal pull-up is selected, the pin uses VDD clocks are disabled. Depending on the device pin as the pull-up source voltage. When the internal count, there are up to 23 external signals (CN0 through pull-down is selected, the pins are pulled down to VSS CN22) that may be selected (enabled) for generating by an internal resistor. Make sure that there is no an interrupt request on a Change-of-State. external pull-up source/pull-down sink when the There are six control registers associated with the ICN internal pull-ups/pull-downs are enabled. module. The CNEN1 and CNEN2 registers contain the Note: Pull-ups and pull-downs on Change Notifi- interrupt enable control bits for each of the CN input cation pins should always be disabled pins. Setting any of these bits enables a CN interrupt whenever the port pin is configured as a for the corresponding pins. digital output. Each CN pin also has a weak pull-up/pull-down connected to it. The pull-ups act as a current source that is connected to the pin. The pull-downs act as a current sink to eliminate the need for external resistors when push button or keypad devices are connected. EXAMPLE 11-1: PORT WRITE/READ EXAMPLE MOV 0xFF00, W0; //Configure PORTB<15:8> as inputs and PORTB<7:0> as outputs MOV W0, TRISB; NOP; //Delay 1 cycle BTSS PORTB, #13; //Next Instruction Equivalent ‘C’ Code TRISB = 0xFF00; //Configure PORTB<15:8> as inputs and PORTB<7:0> as outputs NOP(); //Delay 1 cycle if(PORTBbits.RB13 == 1) // execute following code if PORTB pin 13 is set. { } DS30009995E-page 138  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 12.0 TIMER1 Figure12-1 illustrates a block diagram of the 16-bit Timer1 module. Note: This data sheet summarizes the features of To configure Timer1 for operation: this group of PIC24F devices. It is not intended to be a comprehensive reference 1. Set the TON bit (= 1). source. For more information on Timers, 2. Select the timer prescaler ratio using the refer to the “dsPIC33/PIC24 Family TCKPS<1:0> bits. Reference Manual”, “Timers” (DS39704). 3. Set the Clock and Gating modes using the TCS and TGATE bits. The Timer1 module is a 16-bit timer which can serve as 4. Set or clear the TSYNC bit to configure the time counter for the Real-Time Clock (RTC) or synchronous or asynchronous operation. operate as a free-running, interval timer/counter. Timer1 can operate in three modes: 5. Load the timer period value into the PR1 register. • 16-Bit Timer 6. If interrupts are required, set the Timer1 Interrupt • 16-Bit Synchronous Counter Enable bit, T1IE. Use the Timer1 Interrupt Priority • 16-Bit Asynchronous Counter bits, T1IP<2:0>, to set the interrupt priority. Timer1 also supports these features: • Timer Gate Operation • Selectable Prescaler Settings • Timer Operation During CPU Idle and Sleep modes • Interrupt on 16-Bit Period Register Match or Falling Edge of External Gate Signal FIGURE 12-1: 16-BIT TIMER1 MODULE BLOCK DIAGRAM T1ECS<1:0> LPRC TCKPS<1:0> TON 2 SOSCO Gate Prescaler Sync 1, 8, 64, 256 SOSCI SOSCEN TGATE T1CK TCS FOSC/2 TGATE Q D Set T1IF Q CK Reset TMR1 Sync Comparator TSYNC Equal PR1  2011-2017 Microchip Technology Inc. DS30009995E-page 139

PIC24FV32KA304 FAMILY REGISTER 12-1: T1CON: TIMER1 CONTROL REGISTER R/W-0 U-0 R/W-0 U-0 U-0 U-0 R/W-0 R/W-0 TON — TSIDL — — — T1ECS1(1) T1ECS0(1) bit 15 bit 8 U-0 R/W-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0 U-0 — TGATE TCKPS1 TCKPS0 — TSYNC TCS — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 TON: Timer1 On bit 1 = Starts 16-bit Timer1 0 = Stops 16-bit Timer1 bit 14 Unimplemented: Read as ‘0’ bit 13 TSIDL: Timer1 Stop in Idle Mode bit 1 = Discontinues module operation when device enters Idle mode 0 = Continues module operation in Idle mode bit 12-10 Unimplemented: Read as ‘0’ bit 9-8 T1ECS<1:0>: Timer1 Extended Clock Select bits(1) 11 = Reserved; do not use 10 = Timer1 uses the LPRC as the clock source 01 = Timer1 uses the external clock from T1CK 00 = Timer1 uses the Secondary Oscillator (SOSC) as the clock source bit 7 Unimplemented: Read as ‘0’ bit 6 TGATE: Timer1 Gated Time Accumulation Enable bit When TCS = 1: This bit is ignored. When TCS = 0: 1 = Gated time accumulation is enabled 0 = Gated time accumulation is disabled bit 5-4 TCKPS<1:0>: Timer1 Input Clock Prescale Select bits 11 = 1:256 10 = 1:64 01 = 1:8 00 = 1:1 bit 3 Unimplemented: Read as ‘0’ bit 2 TSYNC: Timer1 External Clock Input Synchronization Select bit When TCS = 1: 1 = Synchronizes external clock input 0 = Does not synchronize external clock input When TCS = 0: This bit is ignored. bit 1 TCS: Timer1 Clock Source Select bit 1 = Timer1 clock source is selected by T1ECS<1:0> 0 = Internal clock (FOSC/2) bit 0 Unimplemented: Read as ‘0’ Note 1: The T1ECSx bits are valid only when TCS = 1. DS30009995E-page 140  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 13.0 TIMER2/3 AND TIMER4/5 To configure Timer2/3 or Timer4/5 for 32-bit operation: 1. Set the T32 bit (T2CON<3> or T4CON<3> = 1). Note: This data sheet summarizes the features of 2. Select the prescaler ratio for Timer2 or Timer4 this group of PIC24F devices. It is not using the TCKPS<1:0> bits. intended to be a comprehensive reference source. For more information on Timers, 3. Set the Clock and Gating modes using the TCS refer to the “dsPIC33/PIC24 Family and TGATE bits. Reference Manual”, “Timers” (DS39704). 4. Load the timer period value. PR3 (or PR5) will contain the most significant word of the value, The Timer2/3 and Timer4/5 modules are 32-bit timers, while PR2 (or PR4) contains the least significant which can also be configured as four independent,16-bit word. timers with selectable operating modes. 5. If interrupts are required, set the Timerx Interrupt As a 32-bit timer, Timer2/3 or Timer4/5 operate in three Enable bit, TxIE. Use the Timerx Interrupt Priority modes: bits, TxIP<2:0>, to set the interrupt priority. • Two Independent 16-Bit Timers (Timer2 and 6. Set the TON bit (TxCON<15> = 1). Timer3) with all 16-Bit Operating modes (except The timer value, at any point, is stored in the register Asynchronous Counter mode) pair, TMR3:TMR2 (or TMR5:TMR4). TMR3 (TMR5) • Single 32-Bit Timer always contains the most significant word of the count, • Single 32-Bit Synchronous Counter while TMR2 (TMR4) contains the least significant word. They also support these features: To configure any of the timers for individual 16-bit operation: • Timer Gate Operation • Selectable Prescaler Settings 1. Clear the T32 bit corresponding to that timer (T2CON<3> for Timer2 and Timer3 or • Timer Operation during Idle mode T4CON<3> for Timer4 and Timer5). • Interrupt on a 32-Bit Period Register Match 2. Select the timer prescaler ratio using the • A/D Event Trigger TCKPS<1:0> bits. Individually, all four of the 16-bit timers can function as 3. Set the Clock and Gating modes using the TCS synchronous timers or counters. They also offer the and TGATE bits. features listed above, except for the A/D event trigger 4. Load the timer period value into the PRx (this is implemented only with Timer3). The operating register. modes and enabled features are determined by setting 5. If interrupts are required, set the Timerx Interrupt the appropriate bit(s) in the T2CON, T3CON, T4CON Enable bit, TxIE; use the Timerx Interrupt Priority and T5CON registers. The T2CON,T3CON, T4CON bits, TxIP<2:0>, to set the interrupt priority. and T5CON registers are provided in generic form in Register13-1 and Register13-2, respectively. 6. Set the TON bit (TxCON<15> = 1). For 32-bit timer/counter operation, Timer2/Timer4 is the least significant word (lsw) and Timer3/Timer5 is the most significant word (msw) of the 32-bit timer. Note: For 32-bit operation, T3CON or T5CON control bits are ignored. Only T2CON or T4CON control bits are used for setup and control. Timer2 or Timer4 clock and gate inputs are utilized for the 32-bit timer modules, but an interrupt is generated with the Timer3 or Timer5 interrupt flags.  2011-2017 Microchip Technology Inc. DS30009995E-page 141

PIC24FV32KA304 FAMILY FIGURE 13-1: TIMER2/3 AND TIMER4/5 (32-BIT) BLOCK DIAGRAM TCKPS<1:0> T2CK TON 2 (T4CK) Gate Prescaler Sync 1, 8, 64, 256 TCY TGATE TGATE TCS 1 Q D Set T3IF (T5IF) Q CK 0 PR3 PR2 (PR5) (PR4) A/D Event Trigger(2) Equal Comparator MSB LSB TMR3 TMR2 Sync Reset (TMR5) (TMR4) 16 Read TMR2 (TMR4)(1) Write TMR2 (TMR4)(1) 16 TMR3HLD 16 (TMR5HLD) Data Bus<15:0> Note 1: The 32-Bit Timer Configuration bit, T32, must be set for 32-bit timer/counter operation. All control bits are respective to the T2CON and T4CON registers. 2: The A/D event trigger is available only on Timer2/3 and Timer4/5 in 32-bit mode, and Timer3 and Timer5 in 16-bit mode. DS30009995E-page 142  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY FIGURE 13-2: TIMER2 AND TIMER4 (16-BIT SYNCHRONOUS) BLOCK DIAGRAM TCKPS<1:0> TON 2 T2CK (T4CK) Gate Prescaler Sync 1, 8, 64, 256 TGATE TCY TCS TGATE 1 Q D Set T2IF (T4IF) Q CK 0 Reset TMR2 (TMR4) Sync Comparator Equal PR2 (PR4) FIGURE 13-3: TIMER3 AND TIMER5 (16-BIT ASYNCHRONOUS) BLOCK DIAGRAM TCKPS<1:0> T3CK TON 2 Sync (T5CK) Prescaler 1, 8, 64, 256 TGATE TCY TCS Set T3IF (T5IF) 1 Q D TGATE Q CK 0 Reset TMR3 (TMR5) A/D Event Trigger Comparator Equal PR3 (PR5)  2011-2017 Microchip Technology Inc. DS30009995E-page 143

PIC24FV32KA304 FAMILY REGISTER 13-1: TxCON: TIMER2 AND TIMER4 CONTROL REGISTER R/W-0 U-0 R/W-0 U-0 U-0 U-0 U-0 U-0 TON — TSIDL — — — — — bit 15 bit 8 U-0 R/W-0 R/W-0 R/W-0 R/W-0 U-0 R/W-0 U-0 — TGATE TCKPS1 TCKPS0 T32(1) — TCS — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 TON: Timerx On bit When TxCON<3> = 1: 1 = Starts 32-bit Timerx/y 0 = Stops 32-bit Timerx/y When TxCON<3> = 0: 1 = Starts 16-bit Timerx 0 = Stops 16-bit Timerx bit 14 Unimplemented: Read as ‘0’ bit 13 TSIDL: Timerx Stop in Idle Mode bit 1 = Discontinues module operation when device enters Idle mode 0 = Continues module operation in Idle mode bit 12-7 Unimplemented: Read as ‘0’ bit 6 TGATE: Timerx Gated Time Accumulation Enable bit When TCS = 1: This bit is ignored. When TCS = 0: 1 = Gated time accumulation is enabled 0 = Gated time accumulation is disabled bit 5-4 TCKPS<1:0>: Timerx Input Clock Prescale Select bits 11 = 1:256 10 = 1:64 01 = 1:8 00 = 1:1 bit 3 T32: 32-Bit Timer Mode Select bit(1) 1 = Timer2 and Timer3 or Timer4 and Timer5 form a single 32-bit timer 0 = Timer2 and Timer3 or Timer4 and Timer5 act as two 16-bit timers bit 2 Unimplemented: Read as ‘0’ bit 1 TCS: Timerx Clock Source Select bit 1 = External clock from pin, TxCK (on the rising edge) 0 = Internal clock (FOSC/2) bit 0 Unimplemented: Read as ‘0’ Note 1: In 32-bit mode, the T3CON or T5CON control bits do not affect 32-bit timer operation. DS30009995E-page 144  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 13-2: TyCON: TIMER3 AND TIMER5 CONTROL REGISTER R/W-0 U-0 R/W-0 U-0 U-0 U-0 U-0 U-0 TON(1) — TSIDL(1) — — — — — bit 15 bit 8 U-0 R/W-0 R/W-0 R/W-0 U-0 U-0 R/W-0 U-0 — TGATE(1) TCKPS1(1) TCKPS0(1) — — TCS(1) — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 TON: Timery On bit(1) 1 = Starts 16-bit Timery 0 = Stops 16-bit Timery bit 14 Unimplemented: Read as ‘0’ bit 13 TSIDL: Timery Stop in Idle Mode bit(1) 1 = Discontinues module operation when device enters Idle mode 0 = Continues module operation in Idle mode bit 12-7 Unimplemented: Read as ‘0’ bit 6 TGATE: Timery Gated Time Accumulation Enable bit(1) When TCS = 1: This bit is ignored. When TCS = 0: 1 = Gated time accumulation is enabled 0 = Gated time accumulation is disabled bit 5-4 TCKPS<1:0>: Timery Input Clock Prescale Select bits(1) 11 = 1:256 10 = 1:64 01 = 1:8 00 = 1:1 bit 3-2 Unimplemented: Read as ‘0’ bit 1 TCS: Timery Clock Source Select bit(1) 1 = External clock is from the T3CK pin (on the rising edge) 0 = Internal clock (FOSC/2) bit 0 Unimplemented: Read as ‘0’ Note 1: When 32-bit operation is enabled (TxCON<3> = 1), these bits have no effect on Timery operation. All timer functions are set through the TxCON register.  2011-2017 Microchip Technology Inc. DS30009995E-page 145

PIC24FV32KA304 FAMILY NOTES: DS30009995E-page 146  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 14.0 INPUT CAPTURE WITH 14.1 General Operating Modes DEDICATED TIMERS 14.1.1 SYNCHRONOUS AND TRIGGER Note: This data sheet summarizes the features MODES of this group of PIC24F devices. It is By default, the input capture module operates in a not intended to be a comprehensive Free-Running mode. The internal 16-bit counter, reference source. For more information, ICxTMR, counts up continuously, wrapping around refer to the “dsPIC33/PIC24 Family Refer- from FFFFh to 0000h on each overflow, with its period ence Manual”, “Input Capture with synchronized to the selected external clock source. Dedicated Timer” (DS70000352). When a capture event occurs, the current 16-bit value of the internal counter is written to the FIFO buffer. All devices in the PIC24FV32KA304 family feature three independent input capture modules. Each of the In Synchronous mode, the module begins capturing modules offers a wide range of configuration and events on the ICx pin as soon as its selected clock operating options for capturing external pulse events, source is enabled. Whenever an event occurs on the and generating interrupts. selected Sync source, the internal counter is reset. In Trigger mode, the module waits for a Sync event from Key features of the input capture module include: another internal module to occur before allowing the • Hardware-configurable for 32-bit operation in all internal counter to run. modes by cascading two adjacent modules Standard, free-running operation is selected by setting • Synchronous and Trigger modes of output the SYNCSELx bits to ‘00000’ and clearing the ICTRIG compare operation, with up to 20 user-selectable bit (ICxCON2<7>). Synchronous and Trigger modes Sync/trigger sources available are selected any time the SYNCSELx bits are set to • A 4-level FIFO buffer for capturing and holding any value except ‘00000’. The ICTRIG bit selects timer values for several events either Synchronous or Trigger mode; setting the bit • Configurable interrupt generation selects Trigger mode operation. In both modes, the • Up to 6 clock sources available for each module, SYNCSELx bits determine the Sync/trigger source. driving a separate internal 16-bit counter When the SYNCSELx bits are set to ‘00000’ and The module is controlled through two registers: ICxCON1 ICTRIG is set, the module operates in Software Trigger (Register14-1) and ICxCON2 (Register14-2). A general mode. In this case, capture operations are started by block diagram of the module is shown in Figure14-1. manually setting the TRIGSTAT bit (ICxCON2<6>). FIGURE 14-1: INPUT CAPTURE x BLOCK DIAGRAM ICM<2:0> ICI<1:0> Prescaler Edge Detect Logic Event and Set ICxIF Counter and Interrupt 1:1/4/16 Clock Synchronizer Logic ICx Pin ICTSEL<2:0> Increment 16 IC Clock Clock ICxTMR 4-Level FIFO Buffer Sources Select 16 Trigger and Reset 16 Trigger and Sync Logic ICxBUF Sync Sources SYNCSEL<4:0> Trigger ICOV, ICBNE System Bus  2011-2017 Microchip Technology Inc. DS30009995E-page 147

PIC24FV32KA304 FAMILY 14.1.2 CASCADED (32-BIT) MODE For 32-bit cascaded operations, the setup procedure is slightly different: By default, each module operates independently with its own 16-bit timer. To increase resolution, adjacent 1. Set the IC32 bits for both modules even and odd modules can be configured to function as (ICyCON2<8> and (ICxCON2<8>), enabling the a single 32-bit module. (For example, Modules 1 and 2 even numbered module first. This ensures the are paired, as are Modules 3 and 4, and so on.) The modules will start functioning in unison. odd numbered module (ICx) provides the Least Signif- 2. Set the ICTSELx and SYNCSELx bits for both icant 16 bits of the 32-bit register pairs, and the even modules to select the same Sync/trigger and numbered module (ICy) provides the Most Significant time base source. Set the even module first, 16 bits. Wraparounds of the ICx registers cause an then the odd module. Both modules must use increment of their corresponding ICy registers. the same ICTSELx and SYNCSELx bit settings. Cascaded operation is configured in hardware by 3. Clear the ICTRIG bit of the even module setting the IC32 bit (ICxCON2<8>) for both modules. (ICyCON2<7>). This forces the module to run in Synchronous mode with the odd module, 14.2 Capture Operations regardless of its trigger setting. 4. Use the odd module’s ICIx bits (ICxCON1<6:5>) The input capture module can be configured to capture to the desired interrupt frequency. timer values and generate interrupts on rising edges on ICx or all transitions on ICx. Captures can be configured 5. Use the ICTRIG bit of the odd module to occur on all rising edges or just some (every 4th or (ICxCON2<7>) to configure Trigger or 16th). Interrupts can be independently configured to Synchronous mode operation. generate on each event or a subset of events. Note: For Synchronous mode operation, enable To set up the module for capture operations: the Sync source as the last step. Both input capture modules are held in Reset 1. If Synchronous mode is to be used, disable the until the Sync source is enabled. Sync source before proceeding. 2. Make sure that any previous data has been 6. Use the ICMx bits of the odd module removed from the FIFO by reading ICxBUF until (ICxCON1<2:0>) to set the desired capture the ICBNE bit (ICxCON1<3>) is cleared. mode. 3. Set the SYNCSELx bits (ICxCON2<4:0>) to the The module is ready to capture events when the time desired Sync/trigger source. base and the Sync/trigger source are enabled. When 4. Set the ICTSELx bits (ICxCON1<12:10>) for the ICBNE bit (ICxCON1<3>) becomes set, at least the desired clock source. If the desired clock one capture value is available in the FIFO. Read input source is running, set the ICTSELx bits before capture values from the FIFO until the ICBNE clears the input capture module is enabled, for proper to‘0’. synchronization with the desired clock source. For 32-bit operation, read both the ICxBUF and 5. Set the ICIx bits (ICxCON1<6:5>) to the desired ICyBUF for the full 32-bit timer value (ICxBUF for the interrupt frequency. lsw, ICyBUF for the msw). At least one capture value is 6. Select Synchronous or Trigger mode operation: available in the FIFO buffer when the odd module’s a) Check that the SYNCSELx bits are not set ICBNE bit (ICxCON1<3>) becomes set. Continue to to ‘00000’. read the buffer registers until ICBNE is cleared (performed automatically by hardware). b) For Synchronous mode, clear the ICTRIG bit (ICxCON2<7>). c) For Trigger mode, set ICTRIG and clear the TRIGSTAT bit (ICxCON2<6>). 7. Set the ICMx bits (ICxCON1<2:0>) to the desired operational mode. 8. Enable the selected Sync/trigger source. DS30009995E-page 148  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 14-1: ICxCON1: INPUT CAPTURE x CONTROL REGISTER 1 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 U-0 U-0 — — ICSIDL ICTSEL2 ICTSEL1 ICTSEL0 — — bit 15 bit 8 U-0 R/W-0 R/W-0 R-0, HSC R-0, HSC R/W-0 R/W-0 R/W-0 — ICI1 ICI0 ICOV ICBNE ICM2 ICM1 ICM0 bit 7 bit 0 Legend: HSC = Hardware Settable/Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13 ICSIDL: Input Capture x Module Stop in Idle Control bit 1 = Input capture module halts in CPU Idle mode 0 = Input capture module continues to operate in CPU Idle mode bit 12-10 ICTSEL<2:0>: Input Capture x Timer Select bits 111 = System clock (FOSC/2) 110 = Reserved 101 = Reserved 100 = Timer1 011 = Timer5 010 =T imer4 001 = Timer2 000 = Timer3 bit 9-7 Unimplemented: Read as ‘0’ bit 6-5 ICI<1:0>: Select Number of Captures per Interrupt bits 11 = Interrupt on every fourth capture event 10 = Interrupt on every third capture event 01 = Interrupt on every second capture event 00 = Interrupt on every capture event bit 4 ICOV: Input Capture x Overflow Status Flag bit (read-only) 1 = Input capture overflow occurred 0 = No input capture overflow occurred bit 3 ICBNE: Input Capture x Buffer Empty Status bit (read-only) 1 = Input capture buffer is not empty, at least one more capture value can be read 0 = Input capture buffer is empty bit 2-0 ICM<2:0>: Input Capture Mode Select bits 111 = Interrupt mode: Input capture functions as an interrupt pin only when the device is in Sleep or Idle mode (rising edge detect only, all other control bits are not applicable) 110 = Unused (module disabled) 101 = Prescaler Capture mode: Capture on every 16th rising edge 100 = Prescaler Capture mode: Capture on every 4th rising edge 011 = Simple Capture mode: Capture on every rising edge 010 = Simple Capture mode: Capture on every falling edge 001 = Edge Detect Capture mode: Capture on every edge (rising and falling); ICI<1:0 bits do not control interrupt generation for this mode 000 = Input capture module is turned off  2011-2017 Microchip Technology Inc. DS30009995E-page 149

PIC24FV32KA304 FAMILY REGISTER 14-2: ICxCON2: INPUT CAPTURE x CONTROL REGISTER 2 U-0 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 — — — — — — — IC32 bit 15 bit 8 R/W-0 R/W-0, HS U-0 R/W-0 R/W-1 R/W-1 R/W-0 R/W-1 ICTRIG TRIGSTAT — SYNCSEL4 SYNCSEL3 SYNCSEL2 SYNCSEL1 SYNCSEL0 bit 7 bit 0 Legend: HS = Hardware Settable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-9 Unimplemented: Read as ‘0’ bit 8 IC32: Cascade Two IC Modules Enable bit (32-bit operation) 1 = ICx and ICy operate in cascade as a 32-bit module (this bit must be set in both modules) 0 = ICx functions independently as a 16-bit module bit 7 ICTRIG: Input Capture x Sync/Trigger Select bit 1 = Triggers ICx from source designated by the SYNCSELx bits 0 = Synchronizes ICx with source designated by the SYNCSELx bits bit 6 TRIGSTAT: Timer Trigger Status bit 1 = Timer source has been triggered and is running (set in hardware, can be set in software) 0 = Timer source has not been triggered and is being held clear bit 5 Unimplemented: Read as ‘0’ bit 4-0 SYNCSEL<4:0>: Trigger/Synchronization Source Selection bits 11111 = Reserved 11110 = Reserved 11101 = Reserved 11100 = CTMU(1) 11011 = A/D(1) 11010 = Comparator 3(1) 11001 = Comparator 2(1) 11000 = Comparator 1(1) 10111 = Input Capture 4 10110 = Input Capture 3 10101 = Input Capture 2 10100 = Input Capture 1 10011 = Reserved 10010 = Reserved 1000x = Reserved 01111 = Timer5 01110 = Timer4 01101 = Timer3 01100 = Timer2 01011 = Timer1 01010 = Input Capture 5 01001 = Reserved 01000 = Reserved 00111 = Reserved 00110 = Reserved 00101 = Output Compare 5 00100 = Output Compare 4 00011 = Output Compare 3 00010 = Output Compare 2 00001 = Output Compare 1 00000 = Not synchronized to any other module Note 1: Use these inputs as trigger sources only and never as Sync sources. DS30009995E-page 150  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 15.0 OUTPUT COMPARE WITH In Synchronous mode, the module begins performing DEDICATED TIMERS its compare or PWM operation as soon as its selected clock source is enabled. Whenever an event occurs on Note: This data sheet summarizes the features of the selected Sync source, the module’s internal this group of PIC24F devices. It is not counter is reset. In Trigger mode, the module waits for intended to be a comprehensive reference a Sync event from another internal module to occur source. For more information, refer to before allowing the counter to run. the “dsPIC33/PIC24 Family Reference Free-Running mode is selected by default or any time Manual”, “Output Compare with that the SYNCSELx bits (OCxCON2<4:0>) are set to Dedicated Timer” (DS70005159). ‘00000’. Synchronous or Trigger modes are selected any time the SYNCSELx bits are set to any value All devices in the PIC24FV32KA304 family feature except ‘00000’. The OCTRIG bit (OCxCON2<7>) 3independent output compare modules. Each of these selects either Synchronous or Trigger mode. Setting modules offers a wide range of configuration and this bit selects Trigger mode operation. In both modes, operating options for generating pulse trains on internal the SYNCSELx bits determine the Sync/trigger source. device events. Also, the modules can produce Pulse-Width Modulated (PWM) waveforms for driving 15.1.2 CASCADED (32-BIT) MODE power applications. By default, each module operates independently with Key features of the output compare module include: its own set of 16-bit Timer and Duty Cycle registers. To • Hardware-configurable for 32-bit operation in all increase the range, adjacent even and odd numbered modes by cascading two adjacent modules modules can be configured to function as a single • Synchronous and Trigger modes of output 32-bit module. (For example, Modules 1 and 2 are compare operation, with up to 21 user-selectable paired, as are Modules 3 and 4, and so on.) The odd Sync/trigger sources available numbered module (OCx) provides the Least Significant • Two separate Period registers (a main register, 16 bits of the 32-bit register pairs, and the even numbered module (OCy) provides the Most Significant OCxR, and a secondary register, OCxRS) for greater flexibility in generating pulses of varying 16 bits. Wraparounds of the OCx registers cause an increment of their corresponding OCy registers. widths • Configurable for single pulse or continuous pulse Cascaded operation is configured in hardware by setting generation on an output event, or continuous the OC32 bit (OCxCON2<8>) for both modules. PWM waveform generation • Up to 6 clock sources available for each module, driving a separate internal 16-bit counter 15.1 General Operating Modes 15.1.1 SYNCHRONOUS AND TRIGGER MODES By default, the output compare module operates in a Free-Running mode. The internal 16-bit counter, OCxTMR, counts up continuously, wrapping around from FFFFh to 0000h on each overflow, with its period synchronized to the selected external clock source. Compare or PWM events are generated each time a match between the internal counter and one of the Period registers occurs.  2011-2017 Microchip Technology Inc. DS30009995E-page 151

PIC24FV32KA304 FAMILY FIGURE 15-1: OUTPUT COMPARE x BLOCK DIAGRAM (16-BIT MODE) DCBx OCMx OCxCON1 OCINV OCTRIS OCTSELx OCxCON2 FLTOUT SYNCSELx FLTTRIEN TRIGSTAT FLTMD TRIGMODE ENFLTx OCTRIG OCxR OCFLTx Match Event OCx Pin Comparator Increment OC Clock Clock Sources Select OC Output and OCxTMR Reset Fault Logic OCFA/ OCFB/ Match Event CxOUT Comparator Match Event Trigger and TSryigngc eSr oaunrdces Sync Logic OCxRS Reset OCx Interrupt DS30009995E-page 152  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 15.2 Compare Operations For 32-bit cascaded operation, these steps are also necessary: In Compare mode (Figure15-1), the output compare module can be configured for single-shot or continuous 1. Set the OC32 bits for both registers pulse generation. It can also repeatedly toggle an (OCyCON2<8> and (OCxCON2<8>). Enable output pin on each timer event. the even numbered module first to ensure the modules will start functioning in unison. To set up the module for compare operations: 2. Clear the OCTRIG bit of the even module 1. Calculate the required values for the OCxR and (OCyCON2), so the module will run in (for Double Compare modes) OCxRS Duty Synchronous mode. Cycle registers: 3. Configure the desired output and Fault settings a) Determine the instruction clock cycle time. for OCy. Take into account the frequency of the 4. Force the output pin for OCx to the output state external clock to the timer source (if one is by clearing the OCTRIS bit. used) and the timer prescaler settings. 5. If Trigger mode operation is required, configure b) Calculate the time to the rising edge of the the trigger options in OCx by using the OCTRIG output pulse relative to the timer start value (OCxCON2<7>), TRIGSTAT (OCxCON2<6>) (0000h). and SYNCSELx (OCxCON2<4:0>) bits. c) Calculate the time to the falling edge of the 6. Configure the desired Compare or PWM mode pulse, based on the desired pulse width and of operation (OCM<2:0>) for OCy first, then for the time to the rising edge of the pulse. OCx. 2. Write the rising edge value to OCxR and the Depending on the output mode selected, the module falling edge value to OCxRS. holds the OCx pin in its default state and forces a 3. For Trigger mode operations, set OCTRIG to transition to the opposite state when OCxR matches enable Trigger mode. Set or clear TRIGMODE the timer. In Double Compare modes, OCx is forced to configure the trigger operation and back to its default state when a match with OCxRS TRIGSTAT to select a hardware or software occurs. The OCxIF interrupt flag is set after an OCxR trigger. For Synchronous mode, clear OCTRIG. match in Single Compare modes and after each 4. Set the SYNCSEL<4:0> bits to configure the OCxRS match in Double Compare modes. trigger or synchronization source. If free-running Single-shot pulse events only occur once, but may be timer operation is required, set the SYNCSELx repeated by simply rewriting the value of the bits to ‘00000’ (no Sync/trigger source). OCxCON1 register. Continuous pulse events continue 5. Select the time base source with the indefinitely until terminated. OCTSEL<2:0> bits. If the desired clock source is running, set the OCTSEL<2:0> bits before the output compare module is enabled for proper synchronization with the desired clock source. If necessary, set the TON bit for the selected timer which enables the compare time base to count. Synchronous mode operation starts as soon as the synchronization source is enabled; Trigger mode operation starts after a trigger source event occurs. 6. Set the OCM<2:0> bits for the appropriate compare operation (‘0xx’).  2011-2017 Microchip Technology Inc. DS30009995E-page 153

PIC24FV32KA304 FAMILY 15.3 Pulse-Width Modulation (PWM) 4. Select a clock source by writing the Mode OCTSEL2<2:0> (OCxCON<12:10>) bits. 5. Enable interrupts, if required, for the timer and In PWM mode, the output compare module can be output compare modules. The output compare configured for edge-aligned or center-aligned pulse interrupt is required for PWM Fault pin utilization. waveform generation. All PWM operations are 6. Select the desired PWM mode in the OCM<2:0> double-buffered (buffer registers are internal to the (OCxCON1<2:0>) bits. module and are not mapped into SFR space). 7. If a timer is selected as a clock source, set the To configure the output compare module for TMRy prescale value and enable the time base by edge-aligned PWM operation: setting the TON (TxCON<15>) bit. 1. Calculate the desired ON time and load it into the OCxR register. 2. Calculate the desired period and load it into the OCxRS register. 3. Select the current OCx as the synchronization source by writing 0x1F to SYNCSEL<4:0> (OCxCON2<4:0>) and ‘0’ to OCTRIG (OCxCON2<7>). FIGURE 15-2: OUTPUT COMPARE x BLOCK DIAGRAM (DOUBLE-BUFFERED, 16-BIT PWM MODE) OCxCON1 OCMx OCxCON2 OCINV OCTSELx OCTRIS SYNCSELx OCxR and DCB<1:0> FLTOUT TRIGSTAT FLTTRIEN TRIGMODE FLTMD Rollover/Reset OCTRIG ENFLTx OCFLTx OCxR and DCB<1:0> Buffers DCB<1:0> OCx Pin Comparator Clock Increment Match OC Clock Event Sources Select OC Output Timing OCxTMR Reset Rollover and Fault Logic OCFA/OCFB/CxOUT Comparator Match Event Match Trigger and Event Trigger and Sync Sources Sync Logic OCxRS Buffer Rollover/Reset OCxRS OCx Interrupt Reset DS30009995E-page 154  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 15.3.1 PWM PERIOD 15.3.2 PWM DUTY CYCLE In Edge-Aligned PWM mode, the period is specified by The PWM duty cycle is specified by writing to the the value of the OCxRS register. In Center-Aligned OCxRS and OCxR registers. The OCxRS and OCxR PWM mode, the period of the synchronization source, registers can be written to at any time, but the duty such as the Timers’ PRy, specifies the period. The cycle value is not latched until a period is complete. period in both cases can be calculated using This provides a double buffer for the PWM duty cycle Equation15-1. and is essential for glitchless PWM operation. Some important boundary parameters of the PWM duty EQUATION 15-1: CALCULATING THE PWM cycle include: PERIOD(1) • Edge-Aligned PWM: PWM Period = [Value + 1] x TCY x (Prescaler Value) - If OCxR and OCxRS are loaded with 0000h, the OCx pin will remain low (0% duty cycle). Where: Value = OCxRS in Edge-Aligned PWM mode - If OCxRS is greater than OCxR, the pin will and can be PRy in Center-Aligned PWM mode remain high (100% duty cycle). (i f TMRy is the Sync source). • Center-Aligned PWM (with TMRy as the Sync source): Note 1: Based on TCY = TOSC * 2; Doze mode and - If OCxR, OCxRS and PRy are all loaded with PLL are disabled. 0000h, the OCx pin will remain low (0% duty cycle). - If OCxRS is greater than PRy, the pin will go high (100% duty cycle). See Example15-3 for PWM mode timing details. Table15-1 and Table15-2 show example PWM frequencies and resolutions for a device operating at 4MIPS and 10 MIPS, respectively. EQUATION 15-2: CALCULATION FOR MAXIMUM PWM RESOLUTION(1) log ( FCY ) 10 FPWM • (Prescale Value) Maximum PWM Resolution (bits) = bits log (2) 10 Note1: Based on FCY = FOSC/2; Doze mode and PLL are disabled. EQUATION 15-3: PWM PERIOD AND DUTY CYCLE CALCULATIONS(1) 1. Find the OCxRS register value for a desired PWM frequency of 52.08 kHz, where FOSC = 8 MHz with PLL (32 MHz device clock rate) and a prescaler setting of 1:1 using Edge-Aligned PWM mode: TCY = 2 • TOSC = 62.5 ns PWM Period = 1/PWM Frequency = 1/52.08 kHz = 19.2s PWM Period = (OCxRS + 1) • TCY • (OCx Prescale Value) 19.2s = (OCxRS + 1) • 62.5 ns • 1 OCxRS = 306 2. Find the maximum resolution of the duty cycle that can be used with a 52.08 kHz frequency and a 32MHz device clock rate: PWM Resolution= log10(FCY/FPWM)/log102) bits = (log (16 MHz/52.08 kHz)/log 2) bits 10 10 = 8.3 bits Note1: Based on TCY = 2 * TOSC; Doze mode and PLL are disabled.  2011-2017 Microchip Technology Inc. DS30009995E-page 155

PIC24FV32KA304 FAMILY 15.4 Subcycle Resolution The DCBx bits are intended for use with a clock source identical to the system clock. When an OCx module The DCBx bits (OCxCON2<10:9>) provide for resolu- with enabled prescaler is used, the falling edge delay tion better than one instruction cycle. When used, they caused by the DCBx bits will be referenced to the delay the falling edge generated from a match event by system clock period, rather than the OCx module’s a portion of an instruction cycle. period. For example, setting DCB<1:0> = 10 causes the falling edge to occur halfway through the instruction cycle in which the match event occurs, instead of at the beginning. These bits cannot be used when OCM<2:0>= 001. When operating the module in PWM mode (OCM<2:0> = 110 or 111), the DCBx bits will be double-buffered. TABLE 15-1: EXAMPLE PWM FREQUENCIES AND RESOLUTIONS AT 4 MIPS (FCY = 4 MHz)(1) PWM Frequency 7.6 Hz 61 Hz 122 Hz 977 Hz 3.9 kHz 31.3 kHz 125 kHz Prescaler Ratio 8 1 1 1 1 1 1 Period Value FFFFh FFFFh 7FFFh 0FFFh 03FFh 007Fh 001Fh Resolution (bits) 16 16 15 12 10 7 5 Note 1: Based on FCY = FOSC/2; Doze mode and PLL are disabled. TABLE 15-2: EXAMPLE PWM FREQUENCIES AND RESOLUTIONS AT 16 MIPS (FCY = 16 MHz)(1) PWM Frequency 30.5 Hz 244 Hz 488 Hz 3.9 kHz 15.6 kHz 125 kHz 500 kHz Prescaler Ratio 8 1 1 1 1 1 1 Period Value FFFFh FFFFh 7FFFh 0FFFh 03FFh 007Fh 001Fh Resolution (bits) 16 16 15 12 10 7 5 Note 1: Based on FCY = FOSC/2; Doze mode and PLL are disabled. DS30009995E-page 156  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 15-1: OCxCON1: OUTPUT COMPARE x CONTROL REGISTER 1 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — OCSIDL OCTSEL2 OCTSEL1 OCTSEL0 ENFLT2 ENFLT1 bit 15 bit 8 R/W-0 R/W-0, HSC R/W-0, HSC R/W-0, HSC R/W-0 R/W-0 R/W-0 R/W-0 ENFLT0 OCFLT2 OCFLT1 OCFLT0 TRIGMODE OCM2(1) OCM1(1) OCM0(1) bit 7 bit 0 Legend: HSC = Hardware Settable/Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 Unimplemented: Read as ‘0’ bit 13 OCSIDL: Output Compare x Stop in Idle Mode Control bit 1 = Output Compare x halts in CPU Idle mode 0 = Output Compare x continues to operate in CPU Idle mode bit 12-10 OCTSEL<2:0>: Output Compare x Timer Select bits 111 = System clock 110 = Reserved 101 = Reserved 100 = Timer1 011 = Timer5 010 = Timer4 001 = Timer3 000 = Timer2 bit 9 ENFLT2: Comparator Fault Input Enable bit 1 = Comparator Fault input is enabled 0 = Comparator Fault input is disabled bit 8 ENFLT1: OCFB Fault Input Enable bit 1 = OCFB Fault input is enabled 0 = OCFB Fault input is disabled bit 7 ENFLT0: OCFA Fault Input Enable bit 1 = OCFA Fault input is enabled 0 = OCFA Fault input is disabled bit 6 OCFLT2: PWM Comparator Fault Condition Status bit 1 = PWM comparator Fault condition has occurred (this is cleared in hardware only) 0 = PWM comparator Fault condition has not occurred (this bit is used only when OCM<2:0> = 111) bit 5 OCFLT1: PWM OCFB Fault Input Enable bit 1 = PWM OCFB Fault condition has occurred (this is cleared in hardware only) 0 = PWM OCFB Fault condition has not occurred (this bit is used only when OCM<2:0> = 111) bit 4 OCFLT0: PWM OCFA Fault Condition Status bit 1 = PWM OCFA Fault condition has occurred (this is cleared in hardware only) 0 = PWM OCFA Fault condition has not occurred (this bit is used only when OCM<2:0> = 111) bit 3 TRIGMODE: Trigger Status Mode Select bit 1 = TRIGSTAT (OCxCON2<6>) is cleared when OCxRS = OCxTMR or in software 0 = TRIGSTAT is only cleared by software Note 1: The comparator module used for Fault input varies with the OCx module. OC1 and OC2 use Comparator1; OC3 and OC4 use Comparator 2; OC5 uses Comparator 3.  2011-2017 Microchip Technology Inc. DS30009995E-page 157

PIC24FV32KA304 FAMILY REGISTER 15-1: OCxCON1: OUTPUT COMPARE x CONTROL REGISTER 1 (CONTINUED) bit 2-0 OCM<2:0>: Output Compare x Mode Select bits(1) 111 = Center-Aligned PWM mode on OCx 110 = Edge-Aligned PWM mode on OCx 101 = Double Compare Continuous Pulse mode: Initialize OCx pin low; toggle OCx state continuously on alternate matches of OCxR and OCxRS 100 = Double Compare Single-Shot mode: Initialize OCx pin low; toggle OCx state on matches of OCxR and OCxRS for one cycle 011 = Single Compare Continuous Pulse mode: Compare events continuously toggle the OCx pin 010 = Single Compare Single-Shot mode: Initialize OCx pin high; compare event forces the OCx pin low 001 = Single Compare Single-Shot mode: Initialize OCx pin low, compare event forces the OCx pin high 000 = Output compare channel is disabled Note 1: The comparator module used for Fault input varies with the OCx module. OC1 and OC2 use Comparator1; OC3 and OC4 use Comparator 2; OC5 uses Comparator 3. DS30009995E-page 158  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 15-2: OCxCON2: OUTPUT COMPARE x CONTROL REGISTER 2 R/W-0 R/W-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 FLTMD FLTOUT FLTTRIEN OCINV — DCB1(3) DCB0(3) OC32 bit 15 bit 8 R/W-0 R/W-0, HS R/W-0 R/W-0 R/W-1 R/W-1 R/W-0 R/W-0 OCTRIG TRIGSTAT OCTRIS SYNCSEL4 SYNCSEL3 SYNCSEL2 SYNCSEL1 SYNCSEL0 bit 7 bit 0 Legend: HS = Hardware Settable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 FLTMD: Fault Mode Select bit 1 = Fault mode is maintained until the Fault source is removed and the corresponding OCFLTx bit is cleared in software 0 = Fault mode is maintained until the Fault source is removed and a new PWM period starts bit 14 FLTOUT: Fault Out bit 1 = PWM output is driven high on a Fault 0 = PWM output is driven low on a Fault bit 13 FLTTRIEN: Fault Output State Select bit 1 = Pin is forced to an output on a Fault condition 0 = Pin I/O condition is unaffected by a Fault bit 12 OCINV: Output Compare x Invert bit 1 = OCx output is inverted 0 = OCx output is not inverted bit 11 Unimplemented: Read as ‘0’ bit 10-9 DCB<1:0>: Output Compare x Pulse-Width Least Significant bits(3) 11 = Delays OCx falling edge by 3/4 of the instruction cycle 10 = Delays OCx falling edge by 1/2 of the instruction cycle 01 = Delays OCx falling edge by 1/4 of the instruction cycle 00 = OCx falling edge occurs at the start of the instruction cycle bit 8 OC32: Cascade Two Output Compare Modules Enable bit (32-bit operation) 1 = Cascade module operation is enabled 0 = Cascade module operation is disabled bit 7 OCTRIG: Output Compare x Sync/Trigger Select bit 1 = Triggers OCx from source designated by the SYNCSELx bits 0 = Synchronizes OCx with source designated by the SYNCSELx bits bit 6 TRIGSTAT: Timer Trigger Status bit 1 = Timer source has been triggered and is running 0 = Timer source has not been triggered and is being held clear bit 5 OCTRIS: Output Compare x Output Pin Direction Select bit 1 = OCx pin is tri-stated 0 = Output Compare x peripheral is connected to the OCx pin Note 1: Do not use an output compare module as its own trigger source, either by selecting this mode or another equivalent SYNCSELx setting. 2: Use these inputs as trigger sources only and never as Sync sources. 3: These bits affect the rising edge when OCINV = 1. The bits have no effect when the OCMx bits (OCxCON1<2:0>) = 001.  2011-2017 Microchip Technology Inc. DS30009995E-page 159

PIC24FV32KA304 FAMILY REGISTER 15-2: OCxCON2: OUTPUT COMPARE x CONTROL REGISTER 2 (CONTINUED) bit 4-0 SYNCSEL<4:0>: Trigger/Synchronization Source Selection bits 11111 = This output compare module(1) 11110 = Reserved 11101 = Reserved 11100 = CTMU(2) 11011 = A/D(2) 11010 = Comparator 3(2) 11001 = Comparator 2(2) 11000 = Comparator 1(2) 10111 = Input Capture 4(2) 10110 = Input Capture 3(2) 10101 = Input Capture 2(2) 10100 = Input Capture 1(2) 100xx = Reserved 01111 = Timer5 01110 = Timer4 01101 = Timer3 01100 = Timer2 01011 = Timer1 01010 = Input Capture 5(2) 01001 = Reserved 01000 = Reserved 00111 = Reserved 00110 = Reserved 00101 = Output Compare 5(1) 00100 = Output Compare 4(1) 00011 = Output Compare 3(1) 00010 = Output Compare 2(1) 00001 = Output Compare 1(1) 00000 = Not synchronized to any other module Note 1: Do not use an output compare module as its own trigger source, either by selecting this mode or another equivalent SYNCSELx setting. 2: Use these inputs as trigger sources only and never as Sync sources. 3: These bits affect the rising edge when OCINV = 1. The bits have no effect when the OCMx bits (OCxCON1<2:0>) = 001. DS30009995E-page 160  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 16.0 SERIAL PERIPHERAL To set up the SPI1 module for the Standard Master INTERFACE (SPI) mode of operation: 1. If using interrupts: Note: This data sheet summarizes the features of a) Clear the SPI1IF bit in the IFS0 register. this group of PIC24F devices. It is not b) Set the SPI1IE bit in the IEC0 register. intended to be a comprehensive reference c) Write the respective SPI1IPx bits in the source. For more information on the Serial IPC2 register to set the interrupt priority. Peripheral Interface, refer to the “dsPIC33/PIC24 Family Reference 2. Write the desired settings to the SPI1CON1 and Manual”, “Serial Peripheral Interface SPI1CON2 registers with the MSTEN bit (SPI)” (DS70005185). (SPI1CON1<5>) = 1. 3. Clear the SPIROV bit (SPI1STAT<6>). The Serial Peripheral Interface (SPI) module is a 4. Enable SPI operation by setting the SPIEN bit synchronous serial interface useful for communicating (SPI1STAT<15>). with other peripheral or microcontroller devices. These 5. Write the data to be transmitted to the SPI1BUF peripheral devices may be serial data EEPROMs, shift register. Transmission (and reception) will start registers, display drivers, A/D Converters, etc. The SPI module is compatible with Motorola® SPI and SIOP as soon as data is written to the SPI1BUF register. interfaces. To set up the SPI1 module for the Standard Slave mode The module supports operation in two buffer modes. In of operation: Standard mode, data is shifted through a single serial buffer. In Enhanced Buffer mode, data is shifted 1. Clear the SPI1BUF register. through an 8-level FIFO buffer. 2. If using interrupts: Note: Do not perform Read-Modify-Write opera- a) Clear the SPI1IF bit in the IFS0 register. tions (such as bit-oriented instructions) on b) Set the SPI1IE bit in the IEC0 register. the SPI1BUF register in either Standard or c) Write the respective SPI1IPx bits in the Enhanced Buffer mode. IPC2 register to set the interrupt priority. The module also supports a basic framed SPI protocol 3. Write the desired settings to the SPI1CON1 while operating in either Master or Slave mode. A total and SPI1CON2 registers with the MSTEN bit of four framed SPI configurations are supported. (SPI1CON1<5>) = 0. 4. Clear the SMP bit. The SPI serial interface consists of four pins: 5. If the CKE bit is set, then the SSEN bit • SDI1: Serial Data Input (SPI1CON1<7>) must be set to enable the SS1 • SDO1: Serial Data Output pin. • SCK1: Shift Clock Input or Output 6. Clear the SPIROV bit (SPI1STAT<6>). • SS1: Active-Low Slave Select or Frame 7. Enable SPI operation by setting the SPIEN bit Synchronization I/O Pulse (SPI1STAT<15>). The SPI module can be configured to operate using 2, 3 or 4 pins. In the 3-pin mode, SS1 is not used. In the 2-pin mode, both SDO1 and SS1 are not used. Block diagrams of the module, in Standard and Enhanced Buffer modes, are shown in Figure16-1 and Figure16-2. The devices of the PIC24FV32KA304 family offer two SPI modules on a device. Note: In this section, the SPI modules are referred to as SPIx. Special Function Registers (SFRs) will follow a similar notation. For example, SPI1CON1 or SPI1CON2 refers to the control register for the SPI1module.  2011-2017 Microchip Technology Inc. DS30009995E-page 161

PIC24FV32KA304 FAMILY FIGURE 16-1: SPI1 MODULE BLOCK DIAGRAM (STANDARD BUFFER MODE) SCK1 1:1 to 1:8 1:1/4/16/64 Secondary Primary FCY Prescaler Prescaler SS1/FSYNC1 Sync Control Select Control Clock Edge SPI1CON1<1:0> Shift Control SPI1CON1<4:2> SDO1 Enable SDI1 bit 0 Master Clock SPI1SR Transfer Transfer SPI1BUF Read SPI1BUF Write SPI1BUF 16 Internal Data Bus DS30009995E-page 162  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY To set up the SPI1 module for the Enhanced Buffer To set up the SPI1 module for the Enhanced Buffer Master (EBM) mode of operation: Slave mode of operation: 1. If using interrupts: 1. Clear the SPI1BUF register. a) Clear the SPI1IF bit in the IFS0 register. 2. If using interrupts: b) Set the SPI1IE bit in the IEC0 register. a) Clear the SPI1IF bit in the IFS0 register. c) Write the respective SPI1IPx bits in the b) Set the SPI1IE bit in the IEC0 register. IPC2 register. c) Write the respective SPI1IPx bits in the 2. Write the desired settings to the SPI1CON1 IPC2 register to set the interrupt priority. and SPI1CON2 registers with the MSTEN bit 3. Write the desired settings to the SPI1CON1 and (SPI1CON1<5>) = 1. SPI1CON2 registers with the MSTEN bit 3. Clear the SPIROV bit (SPI1STAT<6>). (SPI1CON1<5>) = 0. 4. Select Enhanced Buffer mode by setting the 4. Clear the SMP bit. SPIBEN bit (SPI1CON2<0>). 5. If the CKE bit is set, then the SSEN bit must be 5. Enable SPI operation by setting the SPIEN bit set, thus enabling the SS1 pin. (SPI1STAT<15>). 6. Clear the SPIROV bit (SPI1STAT<6>). 6. Write the data to be transmitted to the SPI1BUF 7. Select Enhanced Buffer mode by setting the register. Transmission (and reception) will start SPIBEN bit (SPI1CON2<0>). as soon as data is written to the SPI1BUF 8. Enable SPI operation by setting the SPIEN bit register. (SPI1STAT<15>). FIGURE 16-2: SPI1 MODULE BLOCK DIAGRAM (ENHANCED BUFFER MODE) SCK1 1:1 to 1:8 1:1/4/16/64 Secondary Primary FCY Prescaler Prescaler SS1/FSYNC1 Sync Control Select Control Clock Edge SPI1CON1<1:0> Shift Control SPI1CON1<4:2> SDO1 Enable SDI1 bit 0 Master Clock SPI1SR Transfer Transfer 8-Level FIFO 8-Level FIFO Receive Buffer Transmit Buffer SPI1BUF Read SPI1BUF Write SPI1BUF 16 Internal Data Bus  2011-2017 Microchip Technology Inc. DS30009995E-page 163

PIC24FV32KA304 FAMILY REGISTER 16-1: SPIxSTAT: SPIx STATUS AND CONTROL REGISTER R/W-0 U-0 R/W-0 U-0 U-0 R-0, HSC R-0, HSC R-0, HSC SPIEN — SPISIDL — — SPIBEC2 SPIBEC1 SPIBEC0 bit 15 bit 8 R-0, HSC R/C-0, HS R/W-0, HSC R/W-0 R/W-0 R/W-0 R-0, HSC R-0, HSC SRMPT SPIROV SRXMPT SISEL2 SISEL1 SISEL0 SPITBF SPIRBF bit 7 bit 0 Legend: C = Clearable bit HS = Hardware Settable bit HSC = Hardware Settable/Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 SPIEN: SPIx Enable bit 1 = Enables module and configures SCKx, SDOx, SDIx and SSx as serial port pins 0 = Disables module bit 14 Unimplemented: Read as ‘0’ bit 13 SPISIDL: SPIx Stop in Idle Mode bit 1 = Discontinues module operation when device enters Idle mode 0 = Continues module operation in Idle mode bit 12-11 Unimplemented: Read as ‘0’ bit 10-8 SPIBEC<2:0>: SPIx Buffer Element Count bits (valid in Enhanced Buffer mode) Master mode: Number of SPI transfers pending. Slave mode: Number of SPI transfers unread. bit 7 SRMPT: SPIx Shift Register (SPIxSR) Empty bit (valid in Enhanced Buffer mode) 1 = SPIx Shift register is empty and ready to send or receive 0 = SPIx Shift register is not empty bit 6 SPIROV: SPIx Receive Overflow Flag bit 1 = A new byte/word is completely received and discarded (the user software has not read the previous data in the SPI1BUF register) 0 = No overflow has occurred bit 5 SRXMPT: SPIx Receive FIFO Empty bit (valid in Enhanced Buffer mode) 1 = Receive FIFO is empty 0 = Receive FIFO is not empty bit 4-2 SISEL<2:0>: SPIx Buffer Interrupt Mode bits (valid in Enhanced Buffer mode) 111 = Interrupt when SPIx transmit buffer is full (SPITBF bit is set) 110 = Interrupt when last bit is shifted into SPIxSR; as a result, the TX FIFO is empty 101 = Interrupt when the last bit is shifted out of SPIxSR; now the transmit is complete 100 = Interrupt when one data byte is shifted into the SPIxSR; as a result, the TX FIFO has one open spot 011 = Interrupt when SPIx receive buffer is full (SPIRBF bit is set) 010 = Interrupt when SPIx receive buffer is 3/4 or more full 001 = Interrupt when data is available in receive buffer (SRMPT bit is set) 000 = Interrupt when the last data in the receive buffer is read; as a result, the buffer is empty (SRXMPT bit is set) DS30009995E-page 164  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 16-1: SPIxSTAT: SPIx STATUS AND CONTROL REGISTER (CONTINUED) bit 1 SPITBF: SPIx Transmit Buffer Full Status bit 1 = Transmit has not yet started, SPIxTXB is full 0 = Transmit has started, SPIxTXB is empty In Standard Buffer mode: Automatically set in hardware when the CPU writes the SPIxBUF location, loading SPIxTXB. Automatically cleared in hardware when the SPIx module transfers data from SPIxTXB to SPIxSR. In Enhanced Buffer mode: Automatically set in hardware when the CPU writes the SPIxBUF location, loading the last available buffer location. Automatically cleared in hardware when a buffer location is available for a CPU write. bit 0 SPIRBF: SPIx Receive Buffer Full Status bit 1 = Receive is complete, SPIxRXB is full 0 = Receive is not complete, SPIxRXB is empty In Standard Buffer mode: Automatically set in hardware when the SPIx transfers data from the SPIxSR to SPIxRXB. Automatically cleared in hardware when the core reads the SPIxBUF location, reading SPIxRXB. In Enhanced Buffer mode: Automatically set in hardware when SPIx transfers data from SPIxSR to buffer, filling the last unread buffer location. Automatically cleared in hardware when a buffer location is available for a transfer from SPIxSR.  2011-2017 Microchip Technology Inc. DS30009995E-page 165

PIC24FV32KA304 FAMILY REGISTER 16-2: SPIXCON1: SPIx CONTROL REGISTER 1 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — — DISSCK DISSDO MODE16 SMP CKE(1) bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 SSEN CKP MSTEN SPRE2 SPRE1 SPRE0 PPRE1 PPRE0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-13 Unimplemented: Read as ‘0’ bit 12 DISSCK: Disable SCKx pin bit (SPIx Master modes only) 1 = Internal SPIx clock is disabled, pin functions as an I/O 0 = Internal SPIx clock is enabled bit 11 DISSDO: Disables SDOx pin bit 1 = SDOx pin is not used by the module; pin functions as an I/O 0 = SDOx pin is controlled by the module bit 10 MODE16: Word/Byte Communication Select bit 1 = Communication is word-wide (16 bits) 0 = Communication is byte-wide (8 bits) bit 9 SMP: SPIx Data Input Sample Phase bit Master mode: 1 = Input data is sampled at the end of data output time 0 = Input data is sampled at the middle of data output time Slave mode: SMP must be cleared when SPIx is used in Slave mode. bit 8 CKE: Clock Edge Select bit(1) 1 = Serial output data changes on transition from active clock state to Idle clock state (see bit 6) 0 = Serial output data changes on transition from Idle clock state to active clock state (see bit 6) bit 7 SSEN: Slave Select Enable bit (Slave mode) 1 = SSx pin is used for Slave mode 0 = SSx pin is not used by the module; pin is controlled by port function bit 6 CKP: Clock Polarity Select bit 1 = Idle state for clock is a high level; active state is a low level 0 = Idle state for clock is a low level; active state is a high level bit 5 MSTEN: Master Mode Enable bit 1 = Master mode 0 = Slave mode bit 4-2 SPRE<2:0>: Secondary Prescale bits (Master mode) 111 = Secondary prescale 1:1 110 = Secondary prescale 2:1 • • • 000 = Secondary prescale 8:1 Note 1: The CKE bit is not used in the Framed SPI modes. The user should program this bit to ‘0’ for the Framed SPI modes (FRMEN = 1). DS30009995E-page 166  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 16-2: SPIXCON1: SPIx CONTROL REGISTER 1 (CONTINUED) bit 1-0 PPRE<1:0>: Primary Prescale bits (Master mode) 11 = Primary prescale 1:1 10 = Primary prescale 4:1 01 = Primary prescale 16:1 00 = Primary prescale 64:1 Note 1: The CKE bit is not used in the Framed SPI modes. The user should program this bit to ‘0’ for the Framed SPI modes (FRMEN = 1). REGISTER 16-3: SPIxCON2: SPIx CONTROL REGISTER 2 R/W-0 R/W-0 R/W-0 U-0 U-0 U-0 U-0 U-0 FRMEN SPIFSD SPIFPOL — — — — — bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 — — — — — — SPIFE SPIBEN bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 FRMEN: Framed SPIx Support bit 1 = Framed SPIx support is enabled 0 = Framed SPIx support is disabled bit 14 SPIFSD: SPIx Frame Sync Pulse Direction Control on SSx Pin bit 1 = Frame Sync pulse input (slave) 0 = Frame Sync pulse output (master) bit 13 SPIFPOL: SPIx Frame Sync Pulse Polarity bit (Frame mode only) 1 = Frame Sync pulse is active-high 0 = Frame Sync pulse is active-low bit 12-2 Unimplemented: Read as ‘0’ bit 1 SPIFE: SPIx Frame Sync Pulse Edge Select bit 1 = Frame Sync pulse coincides with the first bit clock 0 = Frame Sync pulse precedes the first bit clock bit 0 SPIBEN: SPIx Enhanced Buffer Enable bit 1 = Enhanced buffer is enabled 0 = Enhanced buffer is disabled (Legacy mode)  2011-2017 Microchip Technology Inc. DS30009995E-page 167

PIC24FV32KA304 FAMILY EQUATION 16-1: RELATIONSHIP BETWEEN DEVICE AND SPIx CLOCK SPEED(1) FCY FSCK = Primary Prescaler * Secondary Prescaler Note1: Based on FCY = FOSC/2; Doze mode and PLL are disabled. TABLE 16-1: SAMPLE SCKx FREQUENCIES(1,2) Secondary Prescaler Settings FCY = 16 MHz 1:1 2:1 4:1 6:1 8:1 Primary Prescaler Settings 1:1 Invalid 8000 4000 2667 2000 4:1 4000 2000 1000 667 500 16:1 1000 500 250 167 125 64:1 250 125 63 42 31 FCY = 5 MHz Primary Prescaler Settings 1:1 5000 2500 1250 833 625 4:1 1250 625 313 208 156 16:1 313 156 78 52 39 64:1 78 39 20 13 10 Note 1: Based on FCY = FOSC/2; Doze mode and PLL are disabled. 2: SCKx frequencies are indicated in kHz. DS30009995E-page 168  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 17.0 INTER-INTEGRATED CIRCUIT 17.2 Communicating as a Master in a (I2C) Single Master Environment The details of sending a message in Master mode Note: This data sheet summarizes the features of depends on the communication protocols for the device this group of PIC24F devices. It is not being communicated with. Typically, the sequence of intended to be a comprehensive reference events is as follows: source. For more information on the Inter-Integrated Circuit, refer to the 1. Assert a Start condition on SDAx and SCLx. “dsPIC33/PIC24 Family Reference 2. Send the I2C device address byte to the slave Manual”, “Inter-Integrated Circuit (I2C)” with a write indication. (DS70000195). 3. Wait for and verify an Acknowledge from the The Inter-Integrated Circuit (I2C) module is a serial slave. interface useful for communicating with other 4. Send the first data byte (sometimes known as peripheral or microcontroller devices. These peripheral the command) to the slave. devices may be serial data EEPROMs, display drivers, 5. Wait for and verify an Acknowledge from the A/D Converters, etc. slave. The I2C modules support these features: 6. Send the serial memory address low byte to the slave. • Independent master and slave logic 7. Repeat Steps 4 and 5, until all data bytes are • 7-bit and 10-bit device addresses sent. • General call address, as defined in the I2C protocol 8. Assert a Repeated Start condition on SDAx and • Clock stretching to provide delays for the SCLx. processor to respond to a slave data request 9. Send the device address byte to the slave with • Both 100kHz and 400kHz bus specifications a read indication. • Configurable address masking 10. Wait for and verify an Acknowledge from the • Multi-Master modes to prevent loss of messages slave. in arbitration 11. Enable master reception to receive serial • Bus Repeater mode, allowing the acceptance of memory data. all messages as a slave, regardless of the 12. Generate an ACK or NACK condition at the end address of a received byte of data. • Automatic SCL 13. Generate a Stop condition on SDAx and SCLx. A block diagram of the module is shown in Figure17-1. 17.1 Pin Remapping Options The I2C modules are tied to a fixed pin. To allow flexi- bility with peripheral multiplexing, the I2C1 module in 28-pin devices, can be reassigned to the alternate pins. These alternate pins are designated as SCL1 and SDA1 during device configuration. Pin assignment is controlled by the I2CxSEL Configuration bit. Programming this bit (=0) multiplexes the module to the SCL1 and SDA1 pins. Note: Throughout this section, references to register and bit names that may be associated with a specific I2C module are referred to generically by the use of ‘x’ in place of the specific module number. Thus, “I2CxSTAT” might refer to the Receive Status register for either I2C1 or I2C2.  2011-2017 Microchip Technology Inc. DS30009995E-page 169

PIC24FV32KA304 FAMILY FIGURE 17-1: I2C BLOCK DIAGRAM (I2C1 MODULE IS SHOWN) Internal Data Bus I2C1RCV Read Shift SCL1 Clock I2C1RSR LSB SDA1 Address Match Match Detect Write I2C1MSK Read Write I2C1ADD Read Start and Stop Bit Detect Write Start and Stop Bit Generation I2C1STAT c gi Read o CDoelltiseicotn ol L Write ntr o C I2C1CON Acknowledge Read Generation Clock Stretching Write I2C1TRN LSB Read Shift Clock Reload Control Write BRG Down Counter I2C1BRG Read TCY/2 DS30009995E-page 170  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 17.3 Setting Baud Rate When 17.4 Slave Address Masking Operating as a Bus Master The I2CxMSK register (Register17-3) designates To compute the Baud Rate Generator (BRG) reload address bit positions as “don’t care” for both 7-Bit and value, use Equation17-1. 10-Bit Addressing modes. Setting a particular bit location (= 1) in the I2CxMSK register causes the slave EQUATION 17-1: COMPUTING BAUD RATE module to respond, whether the corresponding RELOAD VALUE(1) address bit value is ‘0’ or ‘1’. For example, when I2CxMSK is set to ‘00100000’, the slave module will detect both addresses: ‘0000000’ and ‘00100000’. FCY FSCL = ---------------------------------------------------------------------- FCY To enable address masking, the Intelligent Peripheral I2CxBRG+1+------------------------------ 10000000 Management Interface (IPMI) must be disabled by clearing the IPMIEN bit (I2C1CON<11>). or Note: As a result of changes in the I2C protocol, FCY FCY  I2CxBRG = ------------–------------------------------ –1 the addresses in Table17-2 are reserved FSCL 10000000 and will not be Acknowledged in Slave mode. This includes any address mask Note1: Based on FCY = FOSC/2; Doze mode and PLL settings that include any of these are disabled. addresses. TABLE 17-1: I2C CLOCK RATES(1) Required I2CxBRG Value Actual System FCY FSCL (Decimal) (Hexadecimal) FSCL 100kHz 16MHz 157 9D 100kHz 100kHz 8MHz 78 4E 100kHz 100kHz 4MHz 39 27 99kHz 400kHz 16MHz 37 25 404kHz 400kHz 8MHz 18 12 404kHz 400kHz 4MHz 9 9 385kHz 400kHz 2MHz 4 4 385kHz 1MHz 16MHz 13 D 1.026MHz 1MHz 8MHz 6 6 1.026MHz 1MHz 4MHz 3 3 0.909MHz Note 1: Based on FCY = FOSC/2; Doze mode and PLL are disabled. TABLE 17-2: I2C RESERVED ADDRESSES(1) Slave R/W Description Address Bit 0000 000 0 General Call Address(2) 0000 000 1 Start Byte 0000 001 x CBus Address 0000 010 x Reserved 0000 011 x Reserved 0000 1xx x HS Mode Master Code 1111 1xx x Reserved 1111 0xx x 10-Bit Slave Upper Byte(3) Note 1: The address bits listed here will never cause an address match, independent of the address mask settings. 2: This address will be Acknowledged only if GCEN=1. 3: A match on this address can only occur on the upper byte in 10-Bit Addressing mode.  2011-2017 Microchip Technology Inc. DS30009995E-page 171

PIC24FV32KA304 FAMILY REGISTER 17-1: I2CxCON: I2Cx CONTROL REGISTER R/W-0 U-0 R/W-0 R/W-1, HC R/W-0 R/W-0 R/W-0 R/W-0 I2CEN — I2CSIDL SCLREL IPMIEN A10M DISSLW SMEN bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0, HC R/W-0, HC R/W-0, HC R/W-0, HC R/W-0, HC GCEN STREN ACKDT ACKEN RCEN PEN RSEN SEN bit 7 bit 0 Legend: HC = Hardware Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 I2CEN: I2Cx Enable bit 1 = Enables the I2Cx module, and configures the SDAx and SCLx pins as serial port pins 0 = Disables the I2Cx module; all I2C pins are controlled by port functions bit 14 Unimplemented: Read as ‘0’ bit 13 I2CSIDL: I2Cx Stop in Idle Mode bit 1 = Discontinues module operation when the device enters an Idle mode 0 = Continues module operation in Idle mode bit 12 SCLREL: SCLx Release Control bit (when operating as I2C slave) 1 = Releases SCLx clock 0 = Holds SCLx clock low (clock stretch) If STREN = 1: The bit is R/W (i.e., software may write ‘0’ to initiate stretch and write ‘1’ to release clock). Hardware is clear at the beginning of the slave transmission. Hardware is clear at the end of slave reception. If STREN = 0: The bit is R/S (i.e., software may only write ‘1’ to release clock). Hardware is clear at the beginning of slave transmission. bit 11 IPMIEN: Intelligent Peripheral Management Interface (IPMI) Enable bit 1 = IPMI Support mode is enabled; all addresses are Acknowledged 0 = IPMI Support mode is disabled bit 10 A10M: 10-Bit Slave Addressing bit 1 = I2CxADD is a 10-bit slave address 0 = I2CxADD is a 7-bit slave address bit 9 DISSLW: Disable Slew Rate Control bit 1 = Slew rate control is disabled 0 = Slew rate control is enabled bit 8 SMEN: SMBus Input Levels bit 1 = Enables I/O pin thresholds compliant with the SMBus specification 0 = Disables the SMBus input thresholds bit 7 GCEN: General Call Enable bit (when operating as I2C slave) 1 = Enables interrupt when a general call address is received in the I2CxRSR (module is enabled for reception) 0 = General call address is disabled bit 6 STREN: SCLx Clock Stretch Enable bit (when operating as I2C slave) Used in conjunction with the SCLREL bit. 1 = Enables software or receives clock stretching 0 = Disables software or receives clock stretching DS30009995E-page 172  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 17-1: I2CxCON: I2Cx CONTROL REGISTER (CONTINUED) bit 5 ACKDT: Acknowledge Data bit (when operating as I2C master; applicable during master receive) Value that will be transmitted when the software initiates an Acknowledge sequence. 1 = Sends NACK during Acknowledge 0 = Sends ACK during Acknowledge bit 4 ACKEN: Acknowledge Sequence Enable bit (when operating as I2C master; applicable during master receive) 1 = Initiates the Acknowledge sequence on the SDAx and SCLx pins, and transmits the ACKDT data bit; hardware is clear at the end of the master Acknowledge sequence 0 = Acknowledge sequence is not in progress bit 3 RCEN: Receive Enable bit (when operating as I2C master) 1 = Enables Receive mode for I2C; hardware is clear at the end of the eighth bit of the master receive data byte 0 = Receive sequence is not in progress bit 2 PEN: Stop Condition Enable bit (when operating as I2C master) 1 = Initiates Stop condition on SDAx and SCLx pins; hardware is clear at end of master Stop sequence 0 = Stop condition is not in progress bit 1 RSEN: Repeated Start Condition Enable bit (when operating as I2C master) 1 = Initiates Repeated Start condition on SDAx and SCLx pins; hardware is clear at the end of the master Repeated Start sequence 0 = Repeated Start condition is not in progress bit 0 SEN: Start Condition Enable bit (when operating as I2C master) 1 = Initiates Start condition on SDAx and SCLx pins; hardware is clear at the end of the master Start sequence 0 = Start condition is not in progress  2011-2017 Microchip Technology Inc. DS30009995E-page 173

PIC24FV32KA304 FAMILY REGISTER 17-2: I2CxSTAT: I2Cx STATUS REGISTER R-0, HSC R-0, HSC U-0 U-0 U-0 R/C-0, HS R-0, HSC R-0, HSC ACKSTAT TRSTAT — — — BCL GCSTAT ADD10 bit 15 bit 8 R/C-0, HS R/C-0, HS R-0, HSC R/C-0, HSC R/C-0, HSC R-0, HSC R-0, HSC R-0, HSC IWCOL I2COV D/A P S R/W RBF TBF bit 7 bit 0 Legend: C = Clearable bit HS = Hardware Settable bit HSC = Hardware Settable/Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 ACKSTAT: Acknowledge Status bit 1 = NACK was detected last 0 = ACK was detected last Hardware is set or clear at the end of Acknowledge. bit 14 TRSTAT: Transmit Status bit (when operating as I2C master; applicable to master transmit operation) 1 = Master transmit is in progress (8 bits + ACK) 0 = Master transmit is not in progress Hardware is set at the beginning of the master transmission; hardware is clear at the end of slave Acknowledge. bit 13-11 Unimplemented: Read as ‘0’ bit 10 BCL: Master Bus Collision Detect bit 1 = A bus collision has been detected during a master operation 0 = No collision Hardware is set at the detection of a bus collision. bit 9 GCSTAT: General Call Status bit 1 = General call address was received 0 = General call address was not received Hardware is set when an address matches the general call address; hardware is clear at Stop detection. bit 8 ADD10: 10-Bit Address Status bit 1 = 10-bit address was matched 0 = 10-bit address was not matched Hardware is set at a match of the 2nd byte of the matched 10-bit address; hardware is clear at Stop detection. bit 7 IWCOL: I2Cx Write Collision Detect bit 1 = An attempt to write to the I2CxTRN register failed because the I2C module is busy 0 = No collision Hardware is set at an occurrence of a write to I2CxTRN while busy (cleared by software). bit 6 I2COV: I2Cx Receive Overflow Flag bit 1 = A byte was received while the I2CxRCV register is still holding the previous byte 0 = No overflow Hardware is set at an attempt to transfer I2CxRSR to I2CxRCV (cleared by software). bit 5 D/A: Data/Address bit (when operating as I2C slave) 1 = Indicates that the last byte received was data 0 = Indicates that the last byte received was the device address Hardware is clear at a device address match; hardware is set by a write to I2CxTRN or by reception of a slave byte. DS30009995E-page 174  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 17-2: I2CxSTAT: I2Cx STATUS REGISTER (CONTINUED) bit 4 P: Stop bit 1 = Indicates that a Stop bit has been detected last 0 = Stop bit was not detected last Hardware is set or cleared when a Start, Repeated Start or Stop is detected. bit 3 S: Start bit 1 = Indicates that a Start (or Repeated Start) bit has been detected last 0 = Start bit was not detected last Hardware is set or clear when a Start, Repeated Start or Stop is detected. bit 2 R/W: Read/Write Information bit (when operating as I2C slave) 1 = Read – indicates data transfer is output from the slave 0 = Write – indicates data transfer is input to the slave Hardware is set or clear after the reception of an I2C device address byte. bit 1 RBF: Receive Buffer Full Status bit 1 = Receive is complete, I2CxRCV is full 0 = Receive is not complete, I2CxRCV is empty Hardware is set when I2CxRCV is written with a received byte; hardware is clear when the software reads I2CxRCV. bit 0 TBF: Transmit Buffer Full Status bit 1 = Transmit is in progress, I2CxTRN is full 0 = Transmit is complete, I2CxTRN is empty Hardware is set when the software writes to I2CxTRN; hardware is clear at the completion of data transmission.  2011-2017 Microchip Technology Inc. DS30009995E-page 175

PIC24FV32KA304 FAMILY REGISTER 17-3: I2CxMSK: I2Cx SLAVE MODE ADDRESS MASK REGISTER U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 — — — — — — AMSK<9:8> bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 AMSK<7:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-10 Unimplemented: Read as ‘0’ bit 9-0 AMSK<9:0>: Mask for Address Bit x Select bits 1 = Enables masking for bit x of an incoming message address; bit match is not required in this position 0 = Disables masking for bit x; bit match is required in this position REGISTER 17-4: PADCFG1: PAD CONFIGURATION CONTROL REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 R/W-0 R/W-0 U-0 U-0 U-0 U-0 — — SMBUSDEL2 SMBUSDEL1 — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-6 Unimplemented: Read as ‘0’ bit 5 SMBUSDEL2: SMBus SDA2 Input Delay Select bit 1 = The I2C2 module is configured for a longer SMBus input delay (nominal 300 ns delay) 0 = The I2C2 module is configured for a legacy input delay (nominal 150 ns delay) bit 4 SMBUSDEL1: SMBus SDA1 Input Delay Select bit 1 = The I2C1 module is configured for a longer SMBus input delay (nominal 300 ns delay) 0 = The I2C1 module is configured for a legacy input delay (nominal 150 ns delay) bit 3-0 Unimplemented: Read as ‘0’ DS30009995E-page 176  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 18.0 UNIVERSAL ASYNCHRONOUS • Baud Rates Ranging from 1Mbps to 15bps at RECEIVER TRANSMITTER 16MIPS • 4-Deep, First-In-First-Out (FIFO) Transmit Data (UART) Buffer Note: This data sheet summarizes the features of • 4-Deep FIFO Receive Data Buffer this group of PIC24F devices. It is not • Parity, Framing and Buffer Overrun Error intended to be a comprehensive reference Detection source. For more information on the Univer- • Support for 9-Bit mode with Address Detect sal Asynchronous Receiver Transmitter, (9th bit = 1) refer to the “dsPIC33/PIC24 Family • Transmit and Receive Interrupts Reference Manual”, “Universal Asyn- • Loopback mode for Diagnostic Support chronous Receiver Transmitter (UART)” • Support for Sync and Break Characters (DS70000582). • Supports Automatic Baud Rate Detection The Universal Asynchronous Receiver Transmitter • IrDA® Encoder and Decoder Logic (UART) module is one of the serial I/O modules • 16x Baud Clock Output for IrDA Support available in this PIC24F device family. The UART is a full-duplex, asynchronous system that can communicate A simplified block diagram of the UARTx is shown in with peripheral devices, such as personal computers, Figure18-1. The UARTx module consists of these LIN/J2602, RS-232 and RS-485 interfaces. This module important hardware elements: also supports a hardware flow control option with the • Baud Rate Generator UxCTS and UxRTS pins, and also includes an IrDA® • Asynchronous Transmitter encoder and decoder. • Asynchronous Receiver The primary features of the UART module are: Note: Throughout this section, references to • Full-Duplex, 8-Bit or 9-Bit Data Transmission register and bit names that may be asso- through the UxTX and UxRX Pins ciated with a specific USART module are • Even, Odd or No Parity Options (for 8-bit data) referred to generically by the use of ‘x’ in • One or Two Stop bits place of the specific module number. • Hardware Flow Control Option with UxCTS and Thus, “UxSTA” might refer to the USART UxRTS pins Status register for either USART1 or • Fully Integrated Baud Rate Generator (IBRG) with USART2. 16-Bit Prescaler FIGURE 18-1: UARTx SIMPLIFIED BLOCK DIAGRAM Baud Rate Generator IrDA® UxBCLK Hardware Flow Control UxRTS UxCTS UARTx Receiver UxRX UARTx Transmitter UxTX  2011-2017 Microchip Technology Inc. DS30009995E-page 177

PIC24FV32KA304 FAMILY 18.1 UARTx Baud Rate Generator The maximum baud rate (BRGH = 0) possible is (BRG) FCY/16 (for UxBRG = 0) and the minimum baud rate possible is FCY/(16 * 65536). The UARTx module includes a dedicated 16-bit Baud Equation18-2 shows the formula for computation of Rate Generator (BRG). The UxBRG register controls the baud rate with BRGH = 1. the period of a free-running, 16-bit timer. Equation18-1 provides the formula for computation of the baud rate EQUATION 18-2: UARTx BAUD RATE WITH with BRGH = 0. BRGH = 1(1) EQUATION 18-1: UARTx BAUD RATE WITH FCY BRGH = 0(1) Baud Rate = 4 • (UxBRG + 1) FCY Baud Rate = FCY UxBRG = – 1 16 • (UxBRG + 1) 4 • Baud Rate UxBRG = FCY – 1 Note 1: Based on FCY = FOSC/2; Doze mode 16 • Baud Rate and PLL are disabled. Note 1: Based on FCY = FOSC/2; Doze mode The maximum baud rate (BRGH = 1) possible is FCY/4 and PLL are disabled. (for UxBRG = 0) and the minimum baud rate possible is FCY/(4 * 65536). Example18-1 provides the calculation of the baud rate Writing a new value to the UxBRG register causes the error for the following conditions: BRG timer to be reset (cleared). This ensures the BRG • FCY = 4 MHz does not wait for a timer overflow before generating the • Desired Baud Rate = 9600 new baud rate. EXAMPLE 18-1: BAUD RATE ERROR CALCULATION (BRGH = 0)(1) Desired Baud Rate = FCY/(16 (UxBRG + 1)) Solving for UxBRG value: UxBRG = ((FCY/Desired Baud Rate)/16) – 1 UxBRG = ((4000000/9600)/16) – 1 UxBRG = 25 Calculated Baud Rate = 4000000/(16 (25 + 1)) = 9615 Error = (Calculated Baud Rate – Desired Baud Rate) Desired Baud Rate = (9615 – 9600)/9600 = 0.16% Note 1: Based on FCY = FOSC/2; Doze mode and PLL are disabled. DS30009995E-page 178  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 18.2 Transmitting in 8-Bit Data Mode 18.5 Receiving in 8-Bit or 9-Bit Data Mode 1. Set up the UARTx: a) Write appropriate values for data, parity and 1. Set up the UARTx (as described in Section18.2 Stop bits. “Transmitting in 8-Bit Data Mode”). b) Write appropriate baud rate value to the 2. Enable the UARTx. UxBRG register. 3. A receive interrupt will be generated when one c) Set up transmit and receive interrupt enable or more data characters have been received, as and priority bits. per interrupt control bit, URXISELx. 2. Enable the UARTx. 4. Read the OERR bit to determine if an overrun 3. Set the UTXEN bit (causes a transmit interrupt, error has occurred. The OERR bit must be reset two cycles after being set). in software. 4. Write the data byte to the lower byte of the 5. Read UxRXREG. UxTXREG word. The value will be immediately The act of reading the UxRXREG character will move transferred to the Transmit Shift Register (TSR) the next character to the top of the receive FIFO, and the serial bit stream will start shifting out including a new set of PERR and FERR values. with the next rising edge of the baud clock. 5. Alternately, the data byte may be transferred 18.6 Operation of UxCTS and UxRTS while UTXEN = 0 and then, the user may set Control Pins UTXEN. This will cause the serial bit stream to begin immediately, because the baud clock will UARTx Clear-to-Send (UxCTS) and Request-to-Send start from a cleared state. (UxRTS) are the two hardware-controlled pins that are 6. A transmit interrupt will be generated as per associated with the UARTx module. These two pins interrupt control bit, UTXISELx. allow the UARTx to operate in Simplex and Flow Con- trol modes. They are implemented to control the 18.3 Transmitting in 9-Bit Data Mode transmission and reception between the Data Terminal Equipment (DTE). The UEN<1:0> bits in the UxMODE 1. Set up the UARTx (as described in Section18.2 register configure these pins. “Transmitting in 8-Bit Data Mode”). 2. Enable the UARTx. 18.7 Infrared Support 3. Set the UTXEN bit (causes a transmit interrupt, The UARTx module provides two types of infrared twocycles after being set). UARTx support: one is the IrDA clock output to support 4. Write UxTXREG as a 16-bit value only. an external IrDA encoder and decoder device (legacy 5. A word write to UxTXREG triggers the transfer module support), and the other is the full implementation of the 9-bit data to the TSR. The serial bit stream of the IrDA encoder and decoder. will start shifting out with the first rising edge of As the IrDA modes require a 16x baud clock, they will the baud clock. only work when the BRGH bit (UxMODE<3>) is ‘0’. 6. A transmit interrupt will be generated as per the setting of control bit, UTXISELx. 18.7.1 EXTERNAL IrDA SUPPORT – IrDA CLOCK OUTPUT 18.4 Break and Sync Transmit To support external IrDA encoder and decoder devices, Sequence the UxBCLK pin (same as the UxRTS pin) can be configured to generate the 16x baud clock. When The following sequence will send a message frame UEN<1:0> = 11, the UxBCLK pin will output the 16x header made up of a Break, followed by an auto-baud baud clock if the UARTx module is enabled; it can be Sync byte. used to support the IrDA codec chip. 1. Configure the UARTx for the desired mode. 2. Set UTXEN and UTXBRK – this sets up the 18.7.2 BUILT-IN IrDA ENCODER AND Break character. DECODER 3. Load the UxTXREG with a dummy character to The UARTx has full implementation of the IrDA initiate transmission (value is ignored). encoder and decoder as part of the UARTx module. 4. Write ‘55h’ to UxTXREG – loads the Sync The built-in IrDA encoder and decoder functionality is character into the transmit FIFO. enabled using the IREN bit (UxMODE<12>). When 5. After the Break has been sent, the UTXBRK bit enabled (IREN = 1), the receive pin (UxRX) acts as the is reset by hardware. The Sync character now input from the infrared receiver. The transmit pin transmits. (UxTX) acts as the output to the infrared transmitter.  2011-2017 Microchip Technology Inc. DS30009995E-page 179

PIC24FV32KA304 FAMILY REGISTER 18-1: UxMODE: UARTx MODE REGISTER R/W-0 U-0 R/W-0 R/W-0 R/W-0 U-0 R/W-0(2) R/W-0(2) UARTEN — USIDL IREN(1) RTSMD — UEN1 UEN0 bit 15 bit 8 R/C-0, HC R/W-0 R/W-0, HC R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 WAKE LPBACK ABAUD RXINV BRGH PDSEL1 PDSEL0 STSEL bit 7 bit 0 Legend: C = Clearable bit HC = Hardware Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 UARTEN: UARTx Enable bit 1 = UARTx is enabled: All UARTx pins are controlled by UARTx, as defined by UEN<1:0> 0 = UARTx is disabled: All UARTx pins are controlled by port latches; UARTx power consumption is minimal bit 14 Unimplemented: Read as ‘0’ bit 13 USIDL: UARTx Stop in Idle Mode bit 1 = Discontinues module operation when the device enters Idle mode 0 = Continues module operation in Idle mode bit 12 IREN: IrDA® Encoder and Decoder Enable bit(1) 1 = IrDA encoder and decoder are enabled 0 = IrDA encoder and decoder are disabled bit 11 RTSMD: Mode Selection for UxRTS Pin bit 1 = UxRTS pin is in Simplex mode 0 = UxRTS pin is in Flow Control mode bit 10 Unimplemented: Read as ‘0’ bit 9-8 UEN<1:0>: UARTx Enable bits(2) 11 = UxTX, UxRX and UxBCLK pins are enabled and used; UxCTS pin is controlled by port latches 10 = UxTX, UxRX, UxCTS and UxRTS pins are enabled and used 01 = UxTX, UxRX and UxRTS pins are enabled and used; UxCTS pin is controlled by port latches 00 = UxTX and UxRX pins are enabled and used; UxCTS and UxRTS/UxBCLK pins are controlled by port latches bit 7 WAKE: Wake-up on Start Bit Detect During Sleep Mode Enable bit 1 = UARTx will continue to sample the UxRX pin; interrupt is generated on the falling edge, bit is cleared in hardware on the following rising edge 0 = No wake-up is enabled bit 6 LPBACK: UARTx Loopback Mode Select bit 1 = Enables Loopback mode 0 = Loopback mode is disabled bit 5 ABAUD: Auto-Baud Enable bit 1 = Enables baud rate measurement on the next character – requires reception of a Sync field (55h); cleared in hardware upon completion 0 = Baud rate measurement is disabled or completed bit 4 RXINV: Receive Polarity Inversion bit 1 = UxRX Idle state is ‘0’ 0 = UxRX Idle state is ‘1’ Note 1: This feature is is only available for the 16x BRG mode (BRGH=0). 2: The bit availability depends on the pin availability. DS30009995E-page 180  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 18-1: UxMODE: UARTx MODE REGISTER (CONTINUED) bit 3 BRGH: High Baud Rate Enable bit 1 = BRG generates 4 clocks per bit period (4x baud clock, High-Speed mode) 0 = BRG generates 16 clocks per bit period (16x baud clock, Standard mode) bit 2-1 PDSEL<1:0>: Parity and Data Selection bits 11 = 9-bit data, no parity 10 = 8-bit data, odd parity 01 = 8-bit data, even parity 00 = 8-bit data, no parity bit 0 STSEL: Stop Bit Selection bit 1 = Two Stop bits 0 = One Stop bit Note 1: This feature is is only available for the 16x BRG mode (BRGH=0). 2: The bit availability depends on the pin availability.  2011-2017 Microchip Technology Inc. DS30009995E-page 181

PIC24FV32KA304 FAMILY REGISTER 18-2: UxSTA: UARTx STATUS AND CONTROL REGISTER R/W-0 R/W-0 R/W-0 U-0 R/W-0, HC R/W-0 R-0, HSC R-1, HSC UTXISEL1 UTXINV UTXISEL0 — UTXBRK UTXEN UTXBF TRMT bit 15 bit 8 R/W-0 R/W-0 R/W-0 R-1, HSC R-0, HSC R-0, HSC R/C-0, HS R-0, HSC URXISEL1 URXISEL0 ADDEN RIDLE PERR FERR OERR URXDA bit 7 bit 0 Legend: HS = Hardware Settable bit C = Clearable bit HSC = Hardware Settable/Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared HC = Hardware Clearable bit bit 15,13 UTXISEL<1:0>: UARTx Transmission Interrupt Mode Selection bits 11 = Reserved; do not use 10 = Interrupt when a character is transferred to the Transmit Shift Register (TSR) and as a result, the transmit buffer becomes empty 01 = Interrupt when the last character is shifted out of the Transmit Shift Register; all transmit operations are completed 00 = Interrupt when a character is transferred to the Transmit Shift Register (this implies there is at least one character open in the transmit buffer) bit 14 UTXINV: IrDA® Encoder Transmit Polarity Inversion bit If IREN = 0: 1 = UxTX Idle ‘0’ 0 = UxTX Idle ‘1’ If IREN = 1: 1 = UxTX Idle ‘1’ 0 = UxTX Idle ‘0’ bit 12 Unimplemented: Read as ‘0’ bit 11 UTXBRK: UARTx Transmit Break bit 1 = Sends Sync Break on next transmission – Start bit, followed by twelve ‘0’ bits, followed by Stop bit; cleared by hardware upon completion 0 = Sync Break transmission is disabled or completed bit 10 UTXEN: UARTx Transmit Enable bit 1 = Transmit is enabled; UxTX pin is controlled by UARTx 0 = Transmit is disabled; any pending transmission is aborted and the buffer is reset. UxTX pin is controlled by the PORT register. bit 9 UTXBF: UARTx Transmit Buffer Full Status bit (read-only) 1 = Transmit buffer is full 0 = Transmit buffer is not full, at least one more character can be written bit 8 TRMT: Transmit Shift Register Empty bit (read-only) 1 = Transmit Shift Register is empty and the transmit buffer is empty (the last transmission has completed) 0 = Transmit Shift Register is not empty; a transmission is in progress or queued bit 7-6 URXISEL<1:0>: UARTx Receive Interrupt Mode Selection bits 11 = Interrupt is set on a RSR transfer, making the receive buffer full (i.e., has 4 data characters) 10 = Interrupt is set on a RSR transfer, making the receive buffer 3/4 full (i.e., has 3 data characters) 0x = Interrupt is set when any character is received and transferred from the RSR to the receive buffer; receive buffer has one or more characters. DS30009995E-page 182  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 18-2: UxSTA: UARTx STATUS AND CONTROL REGISTER (CONTINUED) bit 5 ADDEN: Address Character Detect bit (bit 8 of received data=1) 1 = Address Detect mode is enabled; if 9-bit mode is not selected, this does not take effect 0 = Address Detect mode is disabled bit 4 RIDLE: Receiver Idle bit (read-only) 1 = Receiver is Idle 0 = Receiver is active bit 3 PERR: Parity Error Status bit (read-only) 1 = Parity error has been detected for the current character (character at the top of the receive FIFO) 0 = Parity error has not been detected bit 2 FERR: Framing Error Status bit (read-only) 1 = Framing error has been detected for the current character (character at the top of the receive FIFO) 0 = Framing error has not been detected bit 1 OERR: Receive Buffer Overrun Error Status bit (clear/read-only) 1 = Receive buffer has overflowed 0 = Receive buffer has not overflowed (clearing a previously set OERR bit (10 transition) will reset the receiver buffer and the RSR to the empty state) bit 0 URXDA: UARTx Receive Buffer Data Available bit (read-only) 1 = Receive buffer has data; at least one more characters can be read 0 = Receive buffer is empty  2011-2017 Microchip Technology Inc. DS30009995E-page 183

PIC24FV32KA304 FAMILY REGISTER 18-3: UxTXREG: UARTx TRANSMIT REGISTER U-x U-x U-x U-x U-x U-x U-x W-x — — — — — — — UTX8 bit 15 bit 8 W-x W-x W-x W-x W-x W-x W-x W-x UTX<7:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-9 Unimplemented: Read as ‘0’ bit 8 UTX8: UARTx Data of the Transmitted Character bit (in 9-bit mode) bit 7-0 UTX<7:0>: UARTx Data of the Transmitted Character bits REGISTER 18-4: UxRXREG: UARTx RECEIVE REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 R-0, HSC — — — — — — — URX8 bit 15 bit 8 R-0, HSC R-0, HSC R-0, HSC R-0, HSC R-0, HSC R-0, HSC R-0, HSC R-0, HSC URX<7:0> bit 7 bit 0 Legend: HSC = Hardware Settable/Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-9 Unimplemented: Read as ‘0’ bit 8 URX8: UARTx Data of the Received Character bit (in 9-bit mode) bit 7-0 URX<7:0>: UARTx Data of the Received Character bits DS30009995E-page 184  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 19.0 REAL-TIME CLOCK AND • BCD format for smaller software overhead CALENDAR (RTCC) • Optimized for long-term battery operation • User calibration of the 32.768 kHz clock Note: This data sheet summarizes the features of crystal/32K INTRC frequency with periodic this group of PIC24F devices. It is not auto-adjust intended to be a comprehensive reference • Optimized for long-term battery operation source. For more information on the • Fractional second synchronization Real-Time Clock and Calendar, refer to • Calibration to within ±2.64 seconds error per the “dsPIC33/PIC24 Family Reference month Manual”, “RTCC with External Power Control” (DS39745). • Calibrates up to 260 ppm of crystal error • Ability to periodically wake-up external devices The RTCC provides the user with a Real-Time Clock without CPU intervention (external power control) and Calendar (RTCC) function that can be calibrated. • Power control output for external circuit control Key features of the RTCC module are: • Calibration takes effect every 15 seconds • Operates in Deep Sleep mode • Runs from any one of the following: • Selectable clock source - External Real-Time Clock of 32.768 kHz • Provides hours, minutes and seconds using - Internal 31.25 kHz LPRC Clock 24-hour format - 50 Hz or 60 Hz External Input • Visibility of one half second period • Provides calendar – weekday, date, month 19.1 RTCC Source Clock and year The user can select between the SOSC crystal • Alarm-configurable for half a second, one second, oscillator, LPRC internal oscillator or an external 10 seconds, one minute, 10 minutes, one hour, 50Hz/60 Hz power line input as the clock reference for one day, one week, one month or one year the RTCC module. This gives the user an option to trade • Alarm repeat with decrementing counter off system cost, accuracy and power consumption, • Alarm with indefinite repeat chime based on the overall system needs. • Year 2000 to 2099 leap year correction FIGURE 19-1: RTCC BLOCK DIAGRAM RTCC Clock Domain CPU Clock Domain Input from SOSC/LPRC Oscillator or RCFGCAL External Source RTCC Prescalers ALCFGRPT 0.5 Sec YEAR MTHDY RTCC Timer RTCVAL WKDYHR Alarm MINSEC Event Comparator ALMTHDY Alarm Registers with Masks ALRMVAL ALWDHR ALMINSEC Repeat Counter RTCOUT<1:0> RTCC Interrupt 1s RTCC Interrupt Logic Alarm Pulse RTCC Clock Source Pin RTCOE  2011-2017 Microchip Technology Inc. DS30009995E-page 185

PIC24FV32KA304 FAMILY 19.2 RTCC Module Registers TABLE 19-2: ALRMVAL REGISTER MAPPING The RTCC module registers are organized into three categories: ALRMPTR Alarm Value Register Window • RTCC Control Registers <1:0> ALRMVAL<15:8> ALRMVAL<7:0> • RTCC Value Registers 00 ALRMMIN ALRMSEC • Alarm Value Registers 01 ALRMWD ALRMHR 19.2.1 REGISTER MAPPING 10 ALRMMNTH ALRMDAY To limit the register interface, the RTCC Timer and 11 PWCSTAB PWCSAMP Alarm Time registers are accessed through corre- Considering that the 16-bit core does not distinguish sponding register pointers. The RTCC Value Register between 8-bit and 16-bit read operations, the user must Window (RTCVALH and RTCVALL) uses the RTCPTR be aware that when reading either the ALRMVALH or bits (RCFGCAL<9:8>) to select the desired Timer ALRMVALL bytes, the ALRMPTR<1:0> value will be register pair (see Table19-1). decremented. The same applies to the RTCVALH or By writing the RTCVALH byte, the RTCC Pointer value, RTCVALL bytes with the RTCPTR<1:0> being the RTCPTR<1:0> bits decrement by one until they decremented. reach ‘00’. Once they reach ‘00’, the MINUTES and Note: This only applies to read operations and SECONDS value will be accessible through RTCVALH not write operations. and RTCVALL until the pointer value is manually changed. 19.2.2 WRITE LOCK TABLE 19-1: RTCVAL REGISTER MAPPING In order to perform a write to any of the RTCC Timer registers, the RTCWREN bit (RTCPWC<13>) must be RTCC Value Register Window RTCPTR<1:0> set (see Example19-1). RTCVAL<15:8> RTCVAL<7:0> Note: To avoid accidental writes to the timer, it is 00 MINUTES SECONDS recommended that the RTCWREN bit 01 WEEKDAY HOURS (RCFGCAL<13>) is kept clear at any other time. For the RTCWREN bit to be 10 MONTH DAY set, there is only one instruction cycle time 11 — YEAR window allowed between the 55h/AA The Alarm Value Register Window (ALRMVALH sequence and the setting of RTCWREN. and ALRMVALL) uses the ALRMPTRx bits Therefore, it is recommended that code (ALCFGRPT<9:8>) to select the desired Alarm follow the procedure in Example19-1. register pair (see Table19-2). 19.2.3 SELECTING RTCC CLOCK SOURCE By writing the ALRMVALH byte, the Alarm Pointer value (ALRMPTR<1:0> bits) decrements by one until There are four reference source clock options that can they reach ‘00’. Once they reach ‘00’, the ALRMMIN be selected for the RTCC using the RTCCSEL<1:0> and ALRMSEC value will be accessible through bits: 00 = Secondary Oscillator, 01 = LPRC, 10 = 50Hz ALRMVALH and ALRMVALL, until the pointer value is External Clock and 11 = 60 Hz External Clock. manually changed. EXAMPLE 19-1: SETTING THE RTCWREN BIT asm volatile (“push w7”); asm volatile (“push w8”); asm volatile (“disi #5”); asm volatile (“mov #0x55, w7”); asm volatile (“mov w7, _NVMKEY”); asm volatile (“mov #0xAA, w8”); asm volatile (“mov w8, _NVMKEY”); asm volatile (“bset _RCFGCAL, #13”); //set the RTCWREN bit asm volatile (“pop w8”); asm volatile (“pop w7”); DS30009995E-page 186  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 19.2.4 RTCC CONTROL REGISTERS REGISTER 19-1: RCFGCAL: RTCC CALIBRATION AND CONFIGURATION REGISTER(1) R/W-0 U-0 R/W-0 R-0, HSC R-0, HSC R/W-0 R/W-0 R/W-0 RTCEN(2) — RTCWREN RTCSYNC HALFSEC(3) RTCOE RTCPTR1 RTCPTR0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CAL7 CAL6 CAL5 CAL4 CAL3 CAL2 CAL1 CAL0 bit 7 bit 0 Legend: HSC = Hardware Settable/Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 RTCEN: RTCC Enable bit(2) 1 = RTCC module is enabled 0 = RTCC module is disabled bit 14 Unimplemented: Read as ‘0’ bit 13 RTCWREN: RTCC Value Registers Write Enable bit 1 = RTCVALH and RTCVALL registers can be written to by the user 0 = RTCVALH and RTCVALL registers are locked out from being written to by the user bit 12 RTCSYNC: RTCC Value Registers Read Synchronization bit 1 = RTCVALH, RTCVALL and ALCFGRPT registers can change while reading due to a rollover ripple resulting in an invalid data read. If the register is read twice and results in the same data, the data can be assumed to be valid. 0 = RTCVALH, RTCVALL or ALCFGRPT registers can be read without concern over a rollover ripple bit 11 HALFSEC: Half Second Status bit(3) 1 = Second half period of a second 0 = First half period of a second bit 10 RTCOE: RTCC Output Enable bit 1 = RTCC output is enabled 0 = RTCC output is disabled bit 9-8 RTCPTR<1:0>: RTCC Value Register Window Pointer bits Points to the corresponding RTCC Value registers when reading the RTCVALH and RTCVALL registers. The RTCPTR<1:0> value decrements on every read or write of RTCVALH until it reaches ‘00’. RTCVAL<15:8>: 00 = MINUTES 01 = WEEKDAY 10 = MONTH 11 = Reserved RTCVAL<7:0>: 00 = SECONDS 01 = HOURS 10 = DAY 11 = YEAR Note 1: The RCFGCAL register is only affected by a POR. 2: A write to the RTCEN bit is only allowed when RTCWREN=1. 3: This bit is read-only; it is cleared to ‘0’ on a write to the lower half of the MINSEC register.  2011-2017 Microchip Technology Inc. DS30009995E-page 187

PIC24FV32KA304 FAMILY REGISTER 19-1: RCFGCAL: RTCC CALIBRATION AND CONFIGURATION REGISTER(1) (CONTINUED) bit 7-0 CAL<7:0>: RTC Drift Calibration bits 01111111 = Maximum positive adjustment; adds 508 RTC clock pulses every one minute • • • 00000001 = Minimum positive adjustment; adds 4 RTC clock pulses every one minute 00000000 = No adjustment 11111111 = Minimum negative adjustment; subtracts 4 RTC clock pulses every one minute • • • 10000000 = Maximum negative adjustment; subtracts 512 RTC clock pulses every one minute Note 1: The RCFGCAL register is only affected by a POR. 2: A write to the RTCEN bit is only allowed when RTCWREN=1. 3: This bit is read-only; it is cleared to ‘0’ on a write to the lower half of the MINSEC register. DS30009995E-page 188  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 19-2: RTCPWC: RTCC CONFIGURATION REGISTER 2(1) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PWCEN PWCPOL PWCCPRE PWCSPRE RTCCLK1(2) RTCCLK0(2) RTCOUT1 RTCOUT0 bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 PWCEN: Power Control Enable bit 1 = Power control is enabled 0 = Power control is disabled bit 14 PWCPOL: Power Control Polarity bit 1 = Power control output is active-high 0 = Power control output is active-low bit 13 PWCCPRE: Power Control Control/Stability Prescaler bits 1 = PWC stability window clock is divide-by-2 of source RTCC clock 0 = PWC stability window clock is divide-by-1 of source RTCC clock bit 12 PWCSPRE: Power Control Sample Prescaler bits 1 = PWC sample window clock is divide-by-2 of source RTCC clock 0 = PWC sample window clock is divide-by-1 of source RTCC clock bit 11-10 RTCCLK<1:0>: RTCC Clock Select bits(2) Determines the source of the internal RTCC clock, which is used for all RTCC timer operations. 00 = External Secondary Oscillator (SOSC) 01 = Internal LPRC Oscillator 10 = External power line source – 50Hz 11 = External power line source – 60 Hz bit 9-8 RTCOUT<1:0>: RTCC Output Select bits Determines the source of the RTCC pin output. 00 = RTCC alarm pulse 01 = RTCC seconds clock 10 = RTCC clock 11 = Power control bit 7-0 Unimplemented: Read as ‘0’ Note 1: The RTCPWC register is only affected by a POR. 2: When a new value is written to these register bits, the Seconds Value register should also be written to properly reset the clock prescalers in the RTCC.  2011-2017 Microchip Technology Inc. DS30009995E-page 189

PIC24FV32KA304 FAMILY REGISTER 19-3: ALCFGRPT: ALARM CONFIGURATION REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ALRMEN CHIME AMASK3 AMASK2 AMASK1 AMASK0 ALRMPTR1 ALRMPTR0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ARPT7 ARPT6 ARPT5 ARPT4 ARPT3 ARPT2 ARPT1 ARPT0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 ALRMEN: Alarm Enable bit 1 = Alarm is enabled (cleared automatically after an alarm event whenever ARPT<7:0> = 00h and CHIME=0) 0 = Alarm is disabled bit 14 CHIME: Chime Enable bit 1 = Chime is enabled; ARPT<7:0> bits are allowed to roll over from 00h to FFh 0 = Chime is disabled; ARPT<7:0> bits stop once they reach 00h bit 13-10 AMASK<3:0>: Alarm Mask Configuration bits 0000 = Every half second 0001 = Every second 0010 = Every 10 seconds 0011 = Every minute 0100 = Every 10 minutes 0101 = Every hour 0110 = Once a day 0111 = Once a week 1000 = Once a month 1001 = Once a year (except when configured for February 29th, once every 4 years) 101x = Reserved – do not use 11xx = Reserved – do not use bit 9-8 ALRMPTR<1:0>: Alarm Value Register Window Pointer bits Points to the corresponding Alarm Value registers when reading the ALRMVALH and ALRMVALL registers. The ALRMPTR<1:0> value decrements on every read or write of ALRMVALH until it reaches ‘00’. ALRMVAL<15:8>: 00 = ALRMMIN 01 = ALRMWD 10 = ALRMMNTH 11 = Unimplemented ALRMVAL<7:0>: 00 = ALRMSEC 01 = ALRMHR 10 = ALRMDAY 11 = Unimplemented bit 7-0 ARPT<7:0>: Alarm Repeat Counter Value bits 11111111 = Alarm will repeat 255 more times . . . 00000000 = Alarm will not repeat The counter decrements on any alarm event; it is prevented from rolling over from 00h to FFh unless CHIME=1. DS30009995E-page 190  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 19.2.5 RTCVAL REGISTER MAPPINGS REGISTER 19-4: YEAR: YEAR VALUE REGISTER(1) U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x YRTEN3 YRTEN2 YRTEN2 YRTEN1 YRONE3 YRONE2 YRONE1 YRONE0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 Unimplemented: Read as ‘0’ bit 7-4 YRTEN<3:0>: Binary Coded Decimal Value of Year’s Tens Digit bits Contains a value from 0 to 9. bit 3-0 YRONE<3:0>: Binary Coded Decimal Value of Year’s Ones Digit bits Contains a value from 0 to 9. Note 1: A write to the YEAR register is only allowed when RTCWREN=1. REGISTER 19-5: MTHDY: MONTH AND DAY VALUE REGISTER(1) U-0 U-0 U-0 R/W-x R/W-x R/W-x R/W-x R/W-x — — — MTHTEN0 MTHONE3 MTHONE2 MTHONE1 MTHONE0 bit 15 bit 8 U-0 U-0 R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x — — DAYTEN1 DAYTEN0 DAYONE3 DAYONE2 DAYONE1 DAYONE0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-13 Unimplemented: Read as ‘0’ bit 12 MTHTEN0: Binary Coded Decimal Value of Month’s Tens Digit bit Contains a value of ‘0’ or ‘1’. bit 11-8 MTHONE<3:0>: Binary Coded Decimal Value of Month’s Ones Digit bits Contains a value from 0 to 9. bit 7-6 Unimplemented: Read as ‘0’ bit 5-4 DAYTEN<1:0>: Binary Coded Decimal Value of Day’s Tens Digit bits Contains a value from 0 to 3. bit 3-0 DAYONE<3:0>: Binary Coded Decimal Value of Day’s Ones Digit bits Contains a value from 0 to 9. Note 1: A write to this register is only allowed when RTCWREN=1.  2011-2017 Microchip Technology Inc. DS30009995E-page 191

PIC24FV32KA304 FAMILY REGISTER 19-6: WKDYHR: WEEKDAY AND HOURS VALUE REGISTER(1) U-0 U-0 U-0 U-0 U-0 R/W-x R/W-x R/W-x — — — — — WDAY2 WDAY1 WDAY0 bit 15 bit 8 U-0 U-0 R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x — — HRTEN1 HRTEN0 HRONE3 HRONE2 HRONE1 HRONE0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-11 Unimplemented: Read as ‘0’ bit 10-8 WDAY<2:0>: Binary Coded Decimal Value of Weekday Digit bits Contains a value from 0 to 6. bit 7-6 Unimplemented: Read as ‘0’ bit 5-4 HRTEN<1:0>: Binary Coded Decimal Value of Hour’s Tens Digit bits Contains a value from 0 to 2. bit 3-0 HRONE<3:0>: Binary Coded Decimal Value of Hour’s Ones Digit bits Contains a value from 0 to 9. Note 1: A write to this register is only allowed when RTCWREN=1. REGISTER 19-7: MINSEC: MINUTES AND SECONDS VALUE REGISTER U-0 R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x — MINTEN2 MINTEN1 MINTEN0 MINONE3 MINONE2 MINONE1 MINONE0 bit 15 bit 8 U-0 R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x — SECTEN2 SECTEN1 SECTEN0 SECONE3 SECONE2 SECONE1 SECONE0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 Unimplemented: Read as ‘0’ bit 14-12 MINTEN<2:0>: Binary Coded Decimal Value of Minute’s Tens Digit bits Contains a value from 0 to 5. bit 11-8 MINONE<3:0>: Binary Coded Decimal Value of Minute’s Ones Digit bits Contains a value from 0 to 9. bit 7 Unimplemented: Read as ‘0’ bit 6-4 SECTEN<2:0>: Binary Coded Decimal Value of Second’s Tens Digit bits Contains a value from 0 to 5. bit 3-0 SECONE<3:0>: Binary Coded Decimal Value of Second’s Ones Digit bits Contains a value from 0 to 9. DS30009995E-page 192  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 19.2.6 ALRMVAL REGISTER MAPPINGS REGISTER 19-8: ALMTHDY: ALARM MONTH AND DAY VALUE REGISTER(1) U-0 U-0 U-0 R/W-x R/W-x R/W-x R/W-x R/W-x — — — MTHTEN0 MTHONE3 MTHONE2 MTHONE1 MTHONE0 bit 15 bit 8 U-0 U-0 R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x — — DAYTEN1 DAYTEN0 DAYONE3 DAYONE2 DAYONE1 DAYONE0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-13 Unimplemented: Read as ‘0’ bit 12 MTHTEN0: Binary Coded Decimal Value of Month’s Tens Digit bit Contains a value of ‘0’ or ‘1’. bit 11-8 MTHONE<3:0>: Binary Coded Decimal Value of Month’s Ones Digit bits Contains a value from 0 to 9. bit 7-6 Unimplemented: Read as ‘0’ bit 5-4 DAYTEN<1:0>: Binary Coded Decimal Value of Day’s Tens Digit bits Contains a value from 0 to 3. bit 3-0 DAYONE<3:0>: Binary Coded Decimal Value of Day’s Ones Digit bits Contains a value from 0 to 9. Note 1: A write to this register is only allowed when RTCWREN=1. REGISTER 19-9: ALWDHR: ALARM WEEKDAY AND HOURS VALUE REGISTER(1) U-0 U-0 U-0 U-0 U-0 R/W-x R/W-x R/W-x — — — — — WDAY2 WDAY1 WDAY0 bit 15 bit 8 U-0 U-0 R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x — — HRTEN1 HRTEN0 HRONE3 HRONE2 HRONE1 HRONE0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-11 Unimplemented: Read as ‘0’ bit 10-8 WDAY<2:0>: Binary Coded Decimal Value of Weekday Digit bits Contains a value from 0 to 6. bit 7-6 Unimplemented: Read as ‘0’ bit 5-4 HRTEN<1:0>: Binary Coded Decimal Value of Hour’s Tens Digit bits Contains a value from 0 to 2. bit 3-0 HRONE<3:0>: Binary Coded Decimal Value of Hour’s Ones Digit bits Contains a value from 0 to 9. Note 1: A write to this register is only allowed when RTCWREN=1.  2011-2017 Microchip Technology Inc. DS30009995E-page 193

PIC24FV32KA304 FAMILY REGISTER 19-10: ALMINSEC: ALARM MINUTES AND SECONDS VALUE REGISTER U-0 R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x — MINTEN2 MINTEN1 MINTEN0 MINONE3 MINONE2 MINONE1 MINONE0 bit 15 bit 8 U-0 R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x — SECTEN2 SECTEN1 SECTEN0 SECONE3 SECONE2 SECONE1 SECONE0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 Unimplemented: Read as ‘0’ bit 14-12 MINTEN<2:0>: Binary Coded Decimal Value of Minute’s Tens Digit bits Contains a value from 0 to 5. bit 11-8 MINONE<3:0>: Binary Coded Decimal Value of Minute’s Ones Digit bits Contains a value from 0 to 9. bit 7 Unimplemented: Read as ‘0’ bit 6-4 SECTEN<2:0>: Binary Coded Decimal Value of Second’s Tens Digit bits Contains a value from 0 to 5. bit 3-0 SECONE<3:0>: Binary Coded Decimal Value of Second’s Ones Digit bits Contains a value from 0 to 9. DS30009995E-page 194  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 19-11: RTCCSWT: RTCC CONTROL/SAMPLE WINDOW TIMER REGISTER(1) R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x PWCSTAB7 PWCSTAB6 PWCSTAB5 PWCSTAB4 PWCSTAB3 PWCSTAB2 PWCSTAB1 PWCSTAB0 bit 15 bit 8 R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x R/W-x PWCSAMP7 PWCSAMP6 PWCSAMP5 PWCSAMP4 PWCSAMP3 PWCSAMP2 PWCSAMP1 PWCSAMP0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 PWCSTAB<7:0>: PWM Stability Window Timer bits 11111111 = Stability window is 255 TPWCCLK clock periods • • • 00000000 = Stability window is 0 TPWCCLK clock periods The sample window starts when the alarm event triggers. The stability window timer starts counting from every alarm event when PWCEN = 1. bit 7-0 PWCSAMP<7:0>: PWM Sample Window Timer bits 11111111 = Sample window is always enabled, even when PWCEN = 0 11111110 = Sample window is 254 TPWCCLK clock periods • • • 00000000 = Sample window is 0 TPWCCLK clock periods The sample window timer starts counting at the end of the stability window when PWCEN = 1. If PWCSTAB<7:0> = 00000000, the sample window timer starts counting from every alarm event when PWCEN=1. Note 1: A write to this register is only allowed when RTCWREN = 1.  2011-2017 Microchip Technology Inc. DS30009995E-page 195

PIC24FV32KA304 FAMILY 19.3 Calibration 19.4 Alarm The real-time crystal input can be calibrated using the • Configurable from half second to one year periodic auto-adjust feature. When properly calibrated, • Enabled using the ALRMEN bit the RTCC can provide an error of less than 3 seconds (ALCFGRPT<15>) per month. This is accomplished by finding the number • One-time alarm and repeat alarm options are of error clock pulses and storing the value into the available lower half of the RCFGCAL register. The 8-bit signed value, loaded into the lower half of RCFGCAL, is multi- 19.4.1 CONFIGURING THE ALARM plied by four and will be either added or subtracted from The alarm feature is enabled using the ALRMEN bit. the RTCC timer, once every minute. Refer to the steps This bit is cleared when an alarm is issued. Writes to below for RTCC calibration: ALRMVAL should only take place when ALRMEN = 0. 1. Using another timer resource on the device, the As shown in Figure19-2, the interval selection of the user must find the error of the 32.768kHz crystal. alarm is configured through the AMASKx bits 2. Once the error is known, it must be converted to (ALCFGRPT<13:10>). These bits determine which and the number of error clock pulses per minute. how many digits of the alarm must match the clock 3. a) If the oscillator is faster than ideal (negative value for the alarm to occur. result from Step 2), the RCFGCAL register value The alarm can also be configured to repeat based on a must be negative. This causes the specified preconfigured interval. The amount of times this number of clock pulses to be subtracted from occurs, once the alarm is enabled, is stored in the the timer counter, once every minute. ARPT<7:0> bits (ALCFGRPT<7:0>). When the value b) If the oscillator is slower than ideal (positive of the ARPTx bits equals 00h and the CHIME bit result from Step 2), the RCFGCAL register value (ALCFGRPT<14>) is cleared, the repeat function is must be positive. This causes the specified disabled, and only a single alarm will occur. The alarm number of clock pulses to be subtracted from can be repeated up to 255 times by loading the timer counter, once every minute. ARPT<7:0> with FFh. EQUATION 19-1: After each alarm is issued, the value of the ARPTx bits is decremented by one. Once the value has reached (Ideal Frequency† – Measured Frequency) * 00h, the alarm will be issued one last time, after which, 60 = Clocks per Minute the ALRMEN bit will be cleared automatically and the † Ideal Frequency = 32,768 Hz alarm will turn off. Writes to the lower half of the RCFGCAL register Indefinite repetition of the alarm can occur if the CHIME should only occur when the timer is turned off, or bit = 1. Instead of the alarm being disabled when the value immediately after the rising edge of the seconds pulse, of the ARPTx bits reaches 00h, it rolls over to FFh and except when SECONDS = 00, 15, 30 or 45. This is due continues counting indefinitely while CHIME is set. to the auto-adjust of the RTCC at 15 second intervals. 19.4.2 ALARM INTERRUPT Note: It is up to the user to include, in the error value, the initial error of the crystal: drift At every alarm event, an interrupt is generated. In due to temperature and drift due to crystal addition, an alarm pulse output is provided that aging. operates at half the frequency of the alarm. This output is completely synchronous to the RTCC clock and can be used as a trigger clock to other peripherals. Note: Changing any of the registers, other than the RCFGCAL and ALCFGRPT registers, and the CHIME bit while the alarm is enabled (ALRMEN = 1), can result in a false alarm event leading to a false alarm interrupt. To avoid a false alarm event, the timer and alarm values should only be changed while the alarm is disabled (ALRMEN = 0). It is recommended that the ALCFGRPT register and CHIME bit be changed when RTCSYNC = 0. DS30009995E-page 196  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY FIGURE 19-2: ALARM MASK SETTINGS Day of Alarm Mask Setting the (AMASK<3:0>) Week Month Day Hours Minutes Seconds 0000 - Every half second 0001 - Every second 0010 - Every 10 seconds s 0011 - Every minute s s 0100 - Every 10 minutes m s s 0101 - Every hour m m s s 0110 - Every day h h m m s s 0111 - Every week d h h m m s s 1000 - Every month d d h h m m s s 1001 - Every year(1) m m d d h h m m s s Note 1: Annually, except when configured for February 29. 19.5 POWER CONTROL The polarity of the PWC control signal may be chosen using the PWCPOL register bit. Active-low or The RTCC includes a power control feature that allows active-high may be used with the appropriate external the device to periodically wake-up an external device, switch to turn on or off the power to one or more exter- wait for the device to be stable before sampling wake-up nal devices. The active-low setting may also be used in events from that device and then shut down the external conjunction with an open-drain setting on the RTCC device. This can be done completely autonomously by pin. This setting is able to drive the GND pin(s) of the the RTCC, without the need to wake from the current external device directly (with the appropriate external low-power mode (Sleep, Deep Sleep, etc.). VDD pull-up device), without the need for external To enable this feature, the RTCC must be enabled switches. Finally, the CHIME bit should be set to enable (RTCEN = 1), the PWCEN register bit must be set and the PWC periodicity. the RTCC pin must be driving the PWC control signal (RTCOE = 1 and RTCOUT<1:0> = 11).  2011-2017 Microchip Technology Inc. DS30009995E-page 197

PIC24FV32KA304 FAMILY NOTES: DS30009995E-page 198  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 20.0 32-BIT PROGRAMMABLE The programmable CRC generator provides a CYCLIC REDUNDANCY CHECK hardware implemented method of quickly generating checksums for various networking and security (CRC) GENERATOR applications. It offers the following features: Note: This data sheet summarizes the features of • User-programmable CRC polynomial equation, this group of PIC24F devices. It is not up to 32 bits intended to be a comprehensive reference • Programmable shift direction (little or big-endian) source. For more information, refer to • Independent data and polynomial lengths the “dsPIC33/PIC24 Family Reference • Configurable interrupt output Manual”, “32-Bit Programmable • Data FIFO Cyclic Redundancy Check (CRC)” (DS30009729). A simplified block diagram of the CRC generator is shown in Figure20-1. A simple version of the CRC shift engine is shown in Figure20-2. FIGURE 20-1: CRC BLOCK DIAGRAM CRCDATH CRCDATL Variable FIFO FIFO Empty Event (4x32, 8x16 or 16x8) CRCISEL 2 * FCY Shift Clock 1 Shift Buffer Set CRCIF 0 0 1 LENDIAN Shift Complete Event CRC Shift Engine CRCWDATH CRCWDATL FIGURE 20-2: CRC SHIFT ENGINE DETAIL CRCWDATH CRCWDATL Read/Write Bus X(1)(1) X(2)(1) X(n)(1) Shift Buffer Data Bit 0 Bit 1 Bit 2 Bit n(2) Note 1: Each XOR stage of the shift engine is programmable; see text for details. 2: Polynomial Length n is determined by ([PLEN<4:0>] + 1).  2011-2017 Microchip Technology Inc. DS30009995E-page 199

PIC24FV32KA304 FAMILY 20.1 User Interface The data for which the CRC is to be calculated must first be written into the FIFO. Even if the data width is 20.1.1 POLYNOMIAL INTERFACE less than 8, the smallest data element that can be written into the FIFO is one byte. For example, if the The CRC module can be programmed for CRC DWIDTHx value is 5, then the size of the data is polynomials of up to the 32nd order, using up to 32 bits. DWIDTHx + 1 or 6. The data is written as a whole byte; Polynomial length, which reflects the highest exponent the two unused upper bits are ignored by the module. in the equation, is selected by the PLEN<4:0> bits (CRCCON2<4:0>). Once data is written into the MSb of the CRCDAT registers (that is, MSb as defined by the data width), the The CRCXORL and CRCXORH registers control which value of the VWORD<4:0> bits (CRCCON1<12:8>) exponent terms are included in the equation. Setting a increments by one. For example, if the DWIDTHx value particular bit includes that exponent term in the is 24, the VWORDx bits will increment when bit 7 of equation. Functionally, this includes an XOR operation CRCDATH is written. Therefore, CRCDATL must on the corresponding bit in the CRC engine. Clearing always be written before CRCDATH. this bit disables the XOR. The CRC engine starts shifting data when the CRCGO For example, consider two CRC polynomials, one is a bit is set and the value of the VWORDx bits is greater 16-bit equation and the other is a 32-bit equation: than zero. Each word is copied out of the FIFO into a x16 + x12 + x5 + 1 buffer register, which decrements VWORDx. The data is then shifted out of the buffer. The CRC engine and continues shifting at a rate of two bits per instruction x32 + x26 + x23 + x22 + x16 + x12 + x11 + x10 + cycle until the VWORDx value reaches zero. This x8 + x7 + x5 + x4 + x2 + x + 1 means that for a given data width, it takes half that To program these polynomials into the CRC generator, number of instructions for each word to complete the set the register bits, as shown in Table20-1. calculation. For example, it takes 16 cycles to calculate the CRC for a single word of 32-bit data. Note that the appropriate positions are set to ‘1’ to indicate that they are used in the equation (for example, When the VWORDx value reaches the maximum value X26 and X23). The 0 bit required by the equation is for the configured value of DWIDTHx (4, 8 or 16), the always XORed; thus, X0 is a don’t care. For a CRCFUL bit becomes set. When the VWORDx value polynomial of length, N, it is assumed that the Nth bit will reaches zero, the CRCMPT bit becomes set. The FIFO always be used, regardless of the bit setting. Therefore, is emptied and the VWORD<4:0> bits are set to for a polynomial length of 32, there is no 32nd bit in the ‘00000’ whenever CRCEN is ‘0’. CRCXOR register. At least one instruction cycle must pass, after a write to CRCDAT, before a read of the VWORDx bits is done. 20.1.2 DATA INTERFACE The module incorporates a FIFO that works with a variable data width. Input data width can be configured to any value, between 1 and 32 bits, using the DWIDTH<4:0> bits (CRCCON2<12:8>). When the data width is greater than 15, the FIFO is 4 words deep. When the DWIDTHx value is between 15 and 8, the FIFO is 8 words deep. When the DWIDTHx value is less than 8, the FIFO is 16 words deep. TABLE 20-1: CRC SETUP EXAMPLES FOR 16 AND 32-BIT POLYNOMIAL Bit Values CRC Control Bits 16-Bit Polynomial 32-Bit Polynomial PLEN<4:0> 01111 11111 X<31:16> 0000 0000 0000 000x 0000 0100 1100 0001 X<15:0> 0001 0000 0010 000x 0001 1101 1011 011x DS30009995E-page 200  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 20.1.3 DATA SHIFT DIRECTION 20.2 Registers The LENDIAN bit (CRCCON1<3>) is used to control There are eight registers associated with the module: the shift direction. By default, the CRC will shift data • CRCCON1 through the engine, MSb first. Setting LENDIAN (= 1) causes the CRC to shift data, LSb first. This setting • CRCCON2 allows better integration with various communication • CRCXORL schemes and removes the overhead of reversing the • CRCXORH bit order in software. Note that this only changes the • CRCDATL direction of the data that is shifted into the engine. The • CRCDATH result of the CRC calculation will still be a normal CRC • CRCWDATL result, not a reverse CRC result. • CRCWDATH 20.1.4 INTERRUPT OPERATION The CRCCON1 and CRCCON2 registers (Register20-1 The module generates an interrupt that is configurable and Register20-2) control the operation of the module, by the user for either of two conditions. If CRCISEL is and configure the various settings. The CRCXOR ‘0’, an interrupt is generated when the VWORD<4:0> registers (Register20-3 and Register20-4) select the bits make a transition from a value of ‘1’ to ‘0’. If polynomial terms to be used in the CRC equation. The CRCISEL is ‘1’, an interrupt will be generated after the CRCDAT and CRCWDAT registers are each register CRC operation finishes and the module sets the pairs that serve as buffers for the double-word, input CRCGO bit to ‘0’. Manually setting CRCGO to ‘0’ will data and CRC processed output, respectively. not generate an interrupt. 20.1.5 TYPICAL OPERATION To use the module for a typical CRC calculation: 1. Set the CRCEN bit to enable the module. 2. Configure the module for the desired operation: a) Program the desired polynomial using the CRCXORL and CRCXORH registers, and the PLEN<4:0> bits. b) Configure the data width and shift direction using the DWIDTHx and LENDIAN bits. c) Select the desired interrupt mode using the CRCISEL bit. 3. Preload the FIFO by writing to the CRCDATL and CRCDATH registers until the CRCFUL bit is set or no data is left. 4. Clear old results by writing 00h to CRCWDATL and CRCWDATH. CRCWDAT can also be left unchanged to resume a previously halted calculation. 5. Set the CRCGO bit to start calculation. 6. Write the remaining data into the FIFO as space becomes available. 7. When the calculation completes, CRCGO is automatically cleared. An interrupt will be generated if CRCISEL = 1. 8. Read CRCWDATL and CRCWDATH for the result of the calculation.  2011-2017 Microchip Technology Inc. DS30009995E-page 201

PIC24FV32KA304 FAMILY REGISTER 20-1: CRCCON1: CRC CONTROL REGISTER 1 R/W-0 U-0 R/W-0 R-0 R-0 R-0 R-0 R-0 CRCEN — CSIDL VWORD4 VWORD3 VWORD2 VWORD1 VWORD0 bit 15 bit 8 R-0, HSC R-1, HSC R/W-0 R/W-0, HC R/W-0 U-0 U-0 U-0 CRCFUL CRCMPT CRCISEL CRCGO LENDIAN — — — bit 7 bit 0 Legend: HC = Hardware Clearable bit HSC = Hardware Settable/Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 CRCEN: CRC Enable bit 1 = Module is enabled 0 = Module is enabled All state machines, pointers and CRCWDAT/CRCDAT registers are reset; other SFRs are NOT reset. bit 14 Unimplemented: Read as ‘0’ bit 13 CSIDL: CRC Stop in Idle Mode bit 1 = Discontinues module operation when device enters Idle mode 0 = Continues module operation in Idle mode bit 12-8 VWORD<4:0>: Pointer Value bits Indicates the number of valid words in the FIFO, which has a maximum value of 8 when PLEN<4:0> > 7 or 16 when PLEN<4:0> 7. bit 7 CRCFUL: CRC FIFO Full bit 1 = FIFO is full 0 = FIFO is not full bit 6 CRCMPT: CRC FIFO Empty Bit 1 = FIFO is empty 0 = FIFO is not empty bit 5 CRCISEL: CRC interrupt Selection bit 1 = Interrupt on FIFO is empty; CRC calculation is not complete 0 = Interrupt on shift is complete and CRCWDAT result is ready bit 4 CRCGO: Start CRC bit 1 = Starts CRC serial shifter 0 = CRC serial shifter is turned off bit 3 LENDIAN: Data Shift Direction Select bit 1 = Data word is shifted into the CRC, starting with the LSb (little endian) 0 = Data word is shifted into the CRC, starting with the MSb (big endian) bit 2-0 Unimplemented: Read as ‘0’ DS30009995E-page 202  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 20-2: CRCCON2: CRC CONTROL REGISTER 2 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — — DWIDTH4 DWIDTH3 DWIDTH2 DWIDTH1 DWIDTH0 bit 15 bit 8 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — — — PLEN4 PLEN3 PLEN2 PLEN1 PLEN0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-13 Unimplemented: Read as ‘0’ bit 12-8 DWIDTH<4:0>: Data Width Select bits Defines the width of the data word (Data Word Width = (DWIDTH<4:0>) + 1). bit 7-5 Unimplemented: Read as ‘0’ bit 4-0 PLEN<4:0>: Polynomial Length Select bits Defines the length of the CRC polynomial (Polynomial Length = (PLEN<4:0>) + 1).  2011-2017 Microchip Technology Inc. DS30009995E-page 203

PIC24FV32KA304 FAMILY REGISTER 20-3: CRCXORL: CRC XOR POLYNOMIAL REGISTER, LOW BYTE R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 X<15:8> bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 U-0 X<7:1> — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-1 X<15:1>: XOR of Polynomial Term Xn Enable bits bit 0 Unimplemented: Read as ‘0’ REGISTER 20-4: CRCXORH: CRC XOR POLYNOMIAL REGISTER, HIGH BYTE R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 X<31:24> bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 X<23:16> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-0 X<31:16>: XOR of Polynomial Term Xn Enable bits DS30009995E-page 204  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 21.0 HIGH/LOW-VOLTAGE DETECT An interrupt flag is set if the device experiences an (HLVD) excursion past the trip point in the direction of change. If the interrupt is enabled, the program execution will Note: This data sheet summarizes the features of branch to the interrupt vector address and the software this group of PIC24F devices. It is not can then respond to the interrupt. intended to be a comprehensive reference The HLVD Control register (see Register21-1) source. For more information on the completely controls the operation of the HLVD module. High/Low-Voltage Detect, refer to This allows the circuitry to be “turned off” by the user the“dsPIC33/PIC24 Family Reference under software control, which minimizes the current Manual”, Section 36. “High-Level consumption for the device. Integration with Programmable High/Low-Voltage Detect (HLVD)” (DS39725). The High/Low-Voltage Detect module (HLVD) is a programmable circuit that allows the user to specify both the device voltage trip point and the direction of change. FIGURE 21-1: HIGH/LOW-VOLTAGE DETECT (HLVD) MODULE BLOCK DIAGRAM Externally Generated Trip Point VDD HLVDIN VDD HLVDL<3:0> HLVDEN VDIR X U Set M HLVDIF 1 - o- 6-t 1 Internal Voltage Reference 1.024V Typical HLVDEN  2011-2017 Microchip Technology Inc. DS30009995E-page 205

PIC24FV32KA304 FAMILY REGISTER 21-1: HLVDCON: HIGH/LOW-VOLTAGE DETECT CONTROL REGISTER R/W-0 U-0 R/W-0 U-0 U-0 U-0 U-0 U-0 HLVDEN — HLSIDL — — — — — bit 15 bit 8 R/W-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 VDIR BGVST IRVST — HLVDL3 HLVDL2 HLVDL1 HLVDL0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 HLVDEN: High/Low-Voltage Detect Power Enable bit 1 = HLVD is enabled 0 = HLVD is disabled bit 14 Unimplemented: Read as ‘0’ bit 13 HLSIDL: HLVD Stop in Idle Mode bit 1 = Discontinues module operation when device enters Idle mode 0 = Continues module operation in Idle mode bit 12-8 Unimplemented: Read as ‘0’ bit 7 VDIR: Voltage Change Direction Select bit 1 = Event occurs when voltage equals or exceeds trip point (HLVDL<3:0>) 0 = Event occurs when voltage equals or falls below trip point (HLVDL<3:0>) bit 6 BGVST: Band Gap Voltage Stable Flag bit 1 = Indicates that the band gap voltage is stable 0 = Indicates that the band gap voltage is unstable bit 5 IRVST: Internal Reference Voltage Stable Flag bit 1 = Indicates that the internal reference voltage is stable and the high-voltage detect logic generates the interrupt flag at the specified voltage range 0 = Indicates that the internal reference voltage is unstable and the high-voltage detect logic will not generate the interrupt flag at the specified voltage range, and the HLVD interrupt should not be enabled bit 4 Unimplemented: Read as ‘0’ bit 3-0 HLVDL<3:0>: High/Low-Voltage Detection Limit bits 1111 = External analog input is used (input comes from the HLVDIN pin) 1110 = Trip Point 1(1) 1101 = Trip Point 2(1) 1100 = Trip Point 3(1) • • • 0000 = Trip Point 15(1) Note 1: For the actual trip point, see Section29.0 “Electrical Characteristics”. DS30009995E-page 206  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 22.0 12-BIT A/D CONVERTER WITH The 12-bit A/D Converter module is an enhanced THRESHOLD DETECT version of the 10-bit module offered in some PIC24 devices. Both modules are Successive Approximation Register (SAR) converters at their cores, surrounded Note: This data sheet summarizes the features of by a range of hardware features for flexible this group of PIC24F devices. It is not configuration. This version of the module extends intended to be a comprehensive reference functionality by providing 12-bit resolution, a wider source. For more information on the 12-Bit range of automatic sampling options and tighter A/D Converter with Threshold Detect, refer integration with other analog modules, such as the to the “dsPIC33/PIC24 Family Reference CTMU and a configurable results buffer. This module Manual”, “12-Bit A/D Converter with also includes a unique Threshold Detect feature that Threshold Detect” (DS39739). allows the module itself to make simple decisions The PIC24F 12-bit A/D Converter has the following key based on the conversion results. features: A simplified block diagram for the module is illustrated • Successive Approximation Register (SAR) in Figure22-1. Conversion • Conversion Speeds of up to 100ksps • Up to 32 Analog Input Channels (Internal and External) • Multiple Internal Reference Input Channels • External Voltage Reference Input Pins • Unipolar Differential Sample-and-Hold (S/H) Amplifier • Automated Threshold Scan and Compare Operation to Pre-Evaluate Conversion Results • Selectable Conversion Trigger Source • Fixed-Length (one word per channel), Configurable Conversion Result Buffer • Four Options for Results Alignment • Configurable Interrupt Generation • Operation During CPU Sleep and Idle modes  2011-2017 Microchip Technology Inc. DS30009995E-page 207

PIC24FV32KA304 FAMILY FIGURE 22-1: 12-BIT A/D CONVERTER BLOCK DIAGRAM Internal Data Bus AVDD AVSS ct VR+ e 16 VREF+ Sel R VR- VREF- V VBG Comparator VINH VR- VR+ AN0 VINL S/H DAC AN1 12-Bit SAR Conversion Logic AN2 AN3 Data Formatting AN4 VINH AN5 AN6 A ADC1BUF0: X ADC1BUF17 AN7 U M AN8 AD1CON1 AN9 VINL AD1CON2 AD1CON3 AD1CON5 AD1CHS AD1CHITL AD1CHITH AN14 AD1CSSL VINH AD1CSSH B AN15 X U CTMU M Temp. Sensor VINL CTMU Sample Control Control Logic VBG Conversion Control Input MUX Control 0.215 * VDD Pin Config. Control 0.785 * VDD AVSS AVDD DS30009995E-page 208  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY To perform an A/D conversion: To perform an A/D sample and conversion using Threshold Detect scanning: 1. Configure the A/D module: a) Configure the port pins as analog inputs 1. Configure the A/D module: and/or select band gap reference inputs a) Configure the port pins as analog inputs (ANS<12:10>, ANS<5:0>). (ANS<12:10>, ANS<5,0>). b) Select voltage reference source to match b) Select the voltage reference source to the expected range on the analog inputs match the expected range on the analog (AD1CON2<15:13>). inputs (AD1CON2<15:13>). c) Select the analog conversion clock to c) Select the analog conversion clock to match the desired data rate with the match the desired data rate with the processor clock (AD1CON3<7:0>). processor clock (AD1CON3<7:0>). d) Select the appropriate sample/conver- d) Select the appropriate sample/conversion sion sequence (AD1CON1<7:4> and sequence (AD1CON1<7:4>, AD1CON3<12:8>). AD1CON3<12:8>). e) Select how the conversion results are e) Select how conversion results are presented in the buffer (AD1CON1<9:8>). presented in the buffer (AD1CON1<9:8>). f) Select the interrupt rate (AD1CON2<6:2>). f) Select the interrupt rate (AD1CON2<6:2>). 2. Configure the threshold compare channels: g) Turn on the A/D module (AD1CON1<15>). a) Enable auto-scan – ASEN bit (AD1CON5<15>). 2. Configure the A/D interrupt (if required): b) Select the Compare mode, “Greater Than, a) Clear the AD1IF bit. Less Than or Windowed” – CMx bits b) Select the A/D interrupt priority. (AD1CON5<1:0>). c) Select the threshold compare channels to be scanned (ADCSSH, ADCSSL). d) If the CTMU is required as a current source for a threshold compare channel, enable the corresponding CTMU channel (ADCCTMUENH, ADCCTMUENL). e) Write the threshold values into the corresponding ADC1BUFn registers. f) Turn on the A/D module (AD1CON1<15>). Note: If performing an A/D sample and conversion using Threshold Detect in Sleep Mode, the RC A/D clock source must be selected before entering into Sleep mode. 3. Configure the A/D interrupt (OPTIONAL): a) Clear the AD1IF bit. b) Select the A/D interrupt priority.  2011-2017 Microchip Technology Inc. DS30009995E-page 209

PIC24FV32KA304 FAMILY 22.1 A/D Control Registers indicate if a match condition has occurred. AD1CHITL is always implemented, whereas AD1CHITH may not The 12-bit A/D Converter module uses up to be implemented in devices with 16 or fewer channels. 43registers for its operation. All registers are mapped The AD1CSSH/L registers (Register22-8 and in the data memory space. Register22-9) select the channels to be included for 22.1.1 CONTROL REGISTERS sequential scanning. Depending on the specific device, the module has up to The AD1CTMUENH/L registers (Register22-10 and eleven control and status registers: Register22-11) select the channel(s) to be used by the CTMU during conversions. Selecting a particular • AD1CON1: A/D Control Register 1 channel allows the A/D Converter to control the CTMU • AD1CON2: A/D Control Register 2 (particularly, its current source) and read its data • AD1CON3: A/D Control Register 3 through that channel. AD1CTMUENL is always • AD1CON5: A/D Control Register 5 implemented, whereas AD1CTMUENH may not be implemented in devices with 16 or fewer channels. • AD1CHS: A/D Sample Select Register • AD1CHITH and AD1CHITL: A/D Scan Compare 22.1.2 A/D RESULT BUFFERS Hit Registers The module incorporates a multi-word, dual port RAM, • AD1CSSL and AD1CSSH: A/D Input Scan Select called ADC1BUF. The buffer is composed of at least Registers the same number of word locations as there are • AD1CTMUENH and AD1CTMUENL: CTMU external analog channels for a particular device, with a Enable Registers maximum number of 32. The number of buffer The AD1CON1, AD1CON2 and AD1CON3 registers addresses is always even. Each of the locations is (Register22-1, Register22-2 and Register22-3) mapped into the data memory space and is separately control the overall operation of the A/D module. This addressable. The buffer locations are referred to as includes enabling the module, configuring the ADC1BUF0 through ADC1BUFn (up to 31). conversion clock and voltage reference sources, The A/D result buffers are both readable and writable. selecting the sampling and conversion triggers, and When the module is active (AD1CON<15> = 1), the manually controlling the sample/convert sequences. buffers are read-only, and store the results of A/D The AD1CON5 register (Register22-4) specifically conversions. When the module is inactive controls features of the Threshold Detect operation, (AD1CON<15> = 0), the buffers are both readable and including its function in power-saving modes. writable. In this state, writing to a buffer location The AD1CHS register (Register22-5) selects the input programs a conversion threshold for Threshold Detect channels to be connected to the S/H amplifier. It also operations. allows the choice of input multiplexers and the Buffer contents are not cleared when the module is selection of a reference source for differential deactivated with the ADON bit (AD1CON1<15>). sampling. Conversion results and any programmed threshold The AD1CHITH and AD1CHITL registers values are maintained when ADON is set or cleared. (Register22-6 and Register22-7) are semaphore registers used with Threshold Detect operations. The status of individual bits, or bit pairs in some cases, DS30009995E-page 210  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 22-1: AD1CON1: A/D CONTROL REGISTER 1 R/W-0 U-0 R/W-0 U-0 U-0 R/W-0 R/W-0 R/W-0 ADON — ADSIDL — — MODE12 FORM1 FORM0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 U-0 R/W-0 R/W-0, HSC R/C-0, HSC SSRC3 SSRC2 SSRC1 SSRC0 — ASAM SAMP DONE bit 7 bit 0 Legend: C = Clearable bit U = Unimplemented bit, read as ‘0’ R = Readable bit W = Writable bit HSC = Hardware Settable/Clearable bit -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 ADON: A/D Operating Mode bit 1 = A/D Converter module is operating 0 = A/D Converter is off bit 14 Unimplemented: Read as ‘0’ bit 13 ADSIDL: A/D Stop in Idle Mode bit 1 = Discontinues module operation when device enters Idle mode 0 = Continues module operation in Idle mode bit 12-11 Unimplemented: Read as ‘0’ bit 10 MODE12: 12-Bit Operation Mode bit 1 = 12-bit A/D operation 0 = 10-bit A/D operation bit 9-8 FORM<1:0>: Data Output Format bits (see the following formats) 11 = Fractional result, signed, left-justified 10 = Absolute fractional result, unsigned, left-justified 01 = Decimal result, signed, right-justified 00 = Absolute decimal result, unsigned, right-justified bit 7-4 SSRC<3:0>: Sample Clock Source Select bits 1111 = Not available; do not use • • • 1000 = Not available; do not use 0111 = Internal counter ends sampling and starts conversion (auto-convert) 0110 = Not available; do not use 0101 = Timer1 event ends sampling and starts conversion 0100 = CTMU event ends sampling and starts conversion 0011 = Timer5 event ends sampling and starts conversion 0010 = Timer3 event ends sampling and starts conversion 0001 = INT0 event ends sampling and starts conversion 0000 = Clearing the SAMP bit in software ends sampling and begins conversion bit 3 Unimplemented: Read as ‘0’ bit 2 ASAM: A/D Sample Auto-Start bit 1 = Sampling begins immediately after the last conversion; SAMP bit is auto-set 0 = Sampling begins when the SAMP bit is manually set bit 1 SAMP: A/D Sample Enable bit 1 = A/D Sample-and-Hold amplifiers are sampling 0 = A/D Sample-and-Hold amplifiers are holding bit 0 DONE: A/D Conversion Status bit 1 = A/D conversion cycle has completed 0 = A/D conversion cycle has not started or is in progress  2011-2017 Microchip Technology Inc. DS30009995E-page 211

PIC24FV32KA304 FAMILY REGISTER 22-2: AD1CON2: A/D CONTROL REGISTER 2 R/W-0 R/W-0 R/W-0 r-0 R/W-0 R/W-0 U-0 U-0 PVCFG1 PVCFG0 NVCFG0 — BUFREGEN CSCNA — — bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 BUFS(1) SMPI4 SMPI3 SMPI2 SMPI1 SMPI0 BUFM(1) ALTS bit 7 bit 0 Legend: r = Reserved bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-14 PVCFG<1:0>: Converter Positive Voltage Reference Configuration bits 11 = 4 * Internal VBG(2) 10 = 2 * Internal VBG(3) 01 = External VREF+ 00 = AVDD bit 13 NVCFG0: Converter Negative Voltage Reference Configuration bits 1 = External VREF- 0 = AVSS bit 12 Reserved: Maintain as ‘0’ bit 11 BUFREGEN: A/D Buffer Register Enable bit 1 = Conversion result is loaded into a buffer location determined by the converted channel 0 = A/D result buffer is treated as a FIFO bit 10 CSCNA: Scan Input Selections for CH0+ S/H Input for MUX A Setting bit 1 = Scans inputs 0 = Does not scan inputs bit 9-8 Unimplemented: Read as ‘0’ bit 7 BUFS: Buffer Fill Status bit(1) 1 = A/D is filling the upper half of the buffer; user should access data in the lower half 0 = A/D is filling the lower half of the buffer; user should access data in the upper half bit 6-2 SMPI<4:0>: Sample Rate Interrupt Select bits 11111 = Interrupts at the completion of the conversion for each 32nd sample 11110 = Interrupts at the completion of the conversion for each 31st sample • • • 00001 = Interrupts at the completion of the conversion for every other sample 00000 = Interrupts at the completion of the conversion for each sample bit 1 BUFM: Buffer Fill Mode Select bit(1) 1 = Starts filling the buffer at address, AD1BUF0, on the first interrupt and AD1BUF(n/2) on the next interrupt (Split Buffer mode) 0 = Starts filling the buffer at address, ADCBUF0, and each sequential address on successive interrupts (FIFO mode) Note 1: This is only applicable when the buffer is used in FIFO mode (BUFREGEN=0). In addition, BUFS is only used when BUFM=1. 2: The voltage reference setting will not be within the specification with VDD below 4.5V. 3: The voltage reference setting will not be within the specification with VDD below 2.3V. DS30009995E-page 212  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 22-2: AD1CON2: A/D CONTROL REGISTER 2 (CONTINUED) bit 0 ALTS: Alternate Input Sample Mode Select bit 1 = Uses channel input selects for Sample A on the first sample and Sample B on the next sample 0 = Always uses channel input selects for Sample A Note 1: This is only applicable when the buffer is used in FIFO mode (BUFREGEN=0). In addition, BUFS is only used when BUFM=1. 2: The voltage reference setting will not be within the specification with VDD below 4.5V. 3: The voltage reference setting will not be within the specification with VDD below 2.3V.  2011-2017 Microchip Technology Inc. DS30009995E-page 213

PIC24FV32KA304 FAMILY REGISTER 22-3: AD1CON3: A/D CONTROL REGISTER 3 R/W-0 R-0 r-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ADRC EXTSAM — SAMC4 SAMC3 SAMC2 SAMC1 SAMC0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ADCS7 ADCS6 ADCS5 ADCS4 ADCS3 ADCS2 ADCS1 ADCS0 bit 7 bit 0 Legend: r = Reserved bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 ADRC: A/D Conversion Clock Source bit 1 = RC clock 0 = Clock is derived from the system clock bit 14 EXTSAM: Extended Sampling Time bit 1 = A/D is still sampling after SAMP=0 0 = A/D is finished sampling bit 13 Reserved: Maintain as ‘0’ bit 12-8 SAMC<4:0>: Auto-Sample Time Select bits 11111= 31 TAD • • • 00001= 1 TAD 00000= 0 TAD bit 7-0 ADCS<7:0>: A/D Conversion Clock Select bits 11111111-01000000 = Reserved 00111111 = 64·TCY=TAD • • • 00000001 = 2·TCY=TAD 00000000 = TCY=TAD DS30009995E-page 214  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 22-4: AD1CON5: A/D CONTROL REGISTER 5 R/W-0 R/W-0 R/W-0 R/W-0 r-0 U-0 R/W-0 R/W-0 ASEN(1) LPEN CTMREQ BGREQ — — ASINT1 ASINT0 bit 15 bit 8 U-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 — — — — WM1 WM0 CM1 CM0 bit 7 bit 0 Legend: r = Reserved bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 ASEN: Auto-Scan Enable bit(1) 1 = Auto-scan is enabled 0 = Auto-scan is disabled bit 14 LPEN: Low-Power Enable bit 1 = Returns to Low-Power mode after scan 0 = Remains in Full-Power mode after scan bit 13 CTMREQ: CTMU Request bit 1 = CTMU is enabled when the A/D is enabled and active 0 = CTMU is not enabled by the A/D bit 12 BGREQ: Band Gap Request bit 1 = Band gap is enabled when the A/D is enabled and active 0 = Band gap is not enabled by the A/D bit 11 Reserved: Maintain as ‘0’ bit 10 Unimplemented: Read as ‘0’ bit 9-8 ASINT<1:0>: Auto-Scan (Threshold Detect) Interrupt Mode bits 11 = Interrupt after a Threshold Detect sequence completed and a valid compare has occurred 10 = Interrupt after a valid compare has occurred 01 = Interrupt after a Threshold Detect sequence completed 00 = No interrupt bit 7-4 Unimplemented: Read as ‘0’ bit 3-2 WM<1:0>: Write Mode bits 11 = Reserved 10 = Auto-compare only (conversion results are not saved, but interrupts are generated when a valid match, as defined by the CMx and ASINTx bits, occurs) 01 = Convert and save (conversion results are saved to locations as determined by the register bits when a match, as defined by the CMx bits, occurs) 00 = Legacy operation (conversion data is saved to a location determined by the buffer register bits) bit 1-0 CM<1:0>: Compare Mode bits 11 = Outside Window mode (valid match occurs if the conversion result is outside of the window defined by the corresponding buffer pair) 10 = Inside Window mode (valid match occurs if the conversion result is inside the window defined by the corresponding buffer pair) 01 = Greater Than mode (valid match occurs if the result is greater than the value in the corresponding buffer register) 00 = Less Than mode (valid match occurs if the result is less than the value in the corresponding buffer register) Note 1: When using auto-scan with Threshold Detect (ASEN = 1), do not configure the sample clock source to Auto-Convert mode (SSRCx = 7). Any other available SSRCx selection is valid. To use auto-convert as the sample clock source (SSRCx = 7), make sure ASEN is cleared.  2011-2017 Microchip Technology Inc. DS30009995E-page 215

PIC24FV32KA304 FAMILY R EGISTER 22-5: AD1CHS: A/D SAMPLE SELECT REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CH0NB2 CH0NB1 CH0NB0 CH0SB4 CH0SB3 CH0SB2 CH0SB1 CH0SB0 bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CH0NA2 CH0NA1 CH0NA0 CH0SA4 CH0SA3 CH0SA2 CH0SA1 CH0SA0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-13 CH0NB<2:0>: Sample B Channel 0 Negative Input Select bits 111 = AN6(1) 110 = AN5(2) 101 = AN4 100 = AN3 011 = AN2 010 = AN1 001 = AN0 000 = AVSS bit 12-8 CH0SB<4:0>: S/H Amplifier Positive Input Select for MUX B Multiplexer Setting bits 11111 = Unimplemented, do not use 11110 = AVDD 11101 = AVSS 11100 = Upper guardband rail (0.785 * VDD) 11011 = Lower guardband rail (0.215 * VDD) 11010 = Internal Band Gap Reference (VBG)(3) 11001-10010 = Unimplemented, do not use 10001 = No channels are connected, all inputs are floating (used for CTMU) 10000 = No channels are connected, all inputs are floating (used for CTMU temperature sensor input) 01111 = AN15 01110 = AN14 01101 = AN13 01100 = AN12 01011 = AN11 01010 = AN10 01001 = AN9 01000 = AN8(1) 00111 = AN7(1) 00110 = AN6(1) 00101 = AN5(2) 00100 = AN4 00011 = AN3 00010 = AN2 00001 = AN1 00000 = AN0 bit 7-5 CH0NA<2:0>: Sample A Channel 0 Negative Input Select bits The same definitions as for CHONB<2:0>. bit 4-0 CH0SA<4:0>: Sample A Channel 0 Positive Input Select bits The same definitions as for CHONA<4:0>. Note 1: This is implemented on 44-pin devices only. 2: This is implemented on 28-pin and 44-pin devices only. 3: The band gap value used for this input is 2x or 4x the internal VBG, which is selected when PVCFG<1:0> = 1x. DS30009995E-page 216  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 22-6: AD1CHITH: A/D SCAN COMPARE HIT REGISTER (HIGH WORD)(1) U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 — — — — — — CHH<17:16> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-2 Unimplemented: Read as ‘0’. bit 1-0 CHH<17:16>: A/D Compare Hit bits If CM<1:0>=11: 1 = A/D Result Buffer x has been written with data or a match has occurred 0 = A/D Result Buffer x has not been written with data For All Other Values of CM<1:0>: 1 = A match has occurred on A/D Result Channel x 0 = No match has occurred on A/D Result Channel x Note 1: Unimplemented channels are read as ‘0’. REGISTER 22-7: AD1CHITL: A/D SCAN COMPARE HIT REGISTER (LOW WORD)(1) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CHH<15:8> bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CHH<7:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-0 CHH<15:0>: A/D Compare Hit bits If CM<1:0>=11: 1 = A/D Result Buffer x has been written with data or a match has occurred 0 = A/D Result Buffer x has not been written with data For all other values of CM<1:0>: 1 = A match has occurred on A/D Result Channel x 0 = No match has occurred on A/D Result Channel x Note 1: Unimplemented channels are read as ‘0’.  2011-2017 Microchip Technology Inc. DS30009995E-page 217

PIC24FV32KA304 FAMILY REGISTER 22-8: AD1CSSH: A/D INPUT SCAN SELECT REGISTER (HIGH WORD)(1) U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 U-0 U-0 — CSS<30:26> — — bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 — — — — — — CSS<17:16> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 Unimplemented: Read as ‘0’ bit 14-10 CSS<30:26>: A/D Input Scan Selection bits 1 = Includes corresponding channel for input scan 0 = Skips channel for input scan bit 9-2 Unimplemented: Read as ‘0’ bit 1-0 CSS<17:16>: A/D Input Scan Selection bits 1 = Includes corresponding channel for input scan 0 = Skips channel for input scan Note 1: Unimplemented channels are read as ‘0’. Do not select unimplemented channels for sampling as indeterminate results may be produced. REGISTER 22-9: AD1CSSL: A/D INPUT SCAN SELECT REGISTER (LOW WORD)(1) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CSS<15:8> bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CSS<7:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-0 CSS<15:0>: A/D Input Scan Selection bits 1 = Includes corresponding ANx input for scan 0 = Skips channel for input scan Note 1: Unimplemented channels are read as ‘0’. Do not select unimplemented channels for sampling as indeterminate results may be produced. DS30009995E-page 218  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 22-10: AD1CTMUENH: A/D CTMU ENABLE REGISTER (HIGH WORD)(1) U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 — — — — — — CTMEN<17:16> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-2 Unimplemented: Read as ‘0’. bit 1-0 CTMEN<17:16>: CTMU Enabled During Conversion bits 1 = CTMU is enabled and connected to the selected channel during conversion 0 = CTMU is not connected to this channel Note 1: Unimplemented channels are read as ‘0’. REGISTER 22-11: AD1CTMUENL: A/D CTMU ENABLE REGISTER (LOW WORD)(1) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CTMEN<15:8> bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CTMEN<7:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-0 CTMEN<15:0>: CTMU Enabled During Conversion bits 1 = CTMU is enabled and connected to the selected channel during conversion 0 = CTMU is not connected to this channel Note 1: Unimplemented channels are read as ‘0’.  2011-2017 Microchip Technology Inc. DS30009995E-page 219

PIC24FV32KA304 FAMILY 22.2 A/D Sampling Requirements sampling function must be completed prior to starting the conversion. The internal holding capacitor will be in a The analog input model of the 12-bit A/D Converter is discharged state prior to each sample operation. shown in Figure22-2. The total sampling time for the A/D is a function of the holding capacitor charge time. At least 1 TAD time period should be allowed between conversions for the sample time. For more details, see For the A/D Converter to meet its specified accuracy, the Section 29.0 “Electrical Characteristics”. Charge Holding Capacitor (CHOLD) must be allowed to fully charge to the voltage level on the analog input pin. EQUATION 22-1: A/D CONVERSION CLOCK The Source (RS) impedance, the Interconnect (RIC) PERIOD impedance and the internal Sampling Switch (RSS) impedance combine to directly affect the time required to charge CHOLD. The combined impedance of the analog TAD = TCY(ADCS + 1) sources must, therefore, be small enough to fully charge the holding capacitor within the chosen sample time. To ADCS = TAD – 1 TCY minimize the effects of pin leakage currents on the accuracy of the A/D Converter, the maximum recom- mended Source impedance, RS, is 2.5 k. After the Note: Based on TCY = 2/FOSC; Doze mode analog input channel is selected (changed), this and PLL are disabled. FIGURE 22-2: 12-BIT A/D CONVERTER ANALOG INPUT MODEL RIC  250 Sampling Switch Rs ANx RSS RSS  3 k VA CPIN ILEAKAGE C= H3O2L pDF 500 nA VSS Legend: CPIN = Input Capacitance VT = Threshold Voltage ILEAKAGE = Leakage Current at the Pin Due to Various Junctions RIC = Interconnect Resistance RSS = Sampling Switch Resistance CHOLD = Sample-and-Hold Capacitance (from DAC) Note: The CPIN value depends on the device package and is not tested. The effect of CPIN is negligible if Rs  5 k. DS30009995E-page 220  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 22.3 Transfer Function • The first code transition occurs when the input voltage is ((VR+) – (VR-))/4096 or 1.0LSb. The transfer functions of the A/D Converter in 12-bit • The ‘0000 0000 0001’ code is centered at resolution are shown in Figure22-3. The difference of VR-+(1.5 * ((VR+) – (VR-))/4096). the input voltages, (VINH – VINL), is compared to the • The ‘0010 0000 0000’ code is centered at reference, ((VR+) – (VR-)). VREFL+(2048.5 * ((VR+) – (VR-))/4096). • An input voltage less than VR-+ (((VR-) – (VR-))/4096) converts as ‘0000 0000 0000’. • An input voltage greater than (VR-)+(4095((VR+) – (VR-))/4096) converts as ‘1111 1111 1111’. FIGURE 22-3: 12-BIT A/D TRANSFER FUNCTION Output Code (Binary (Decimal)) 1111 1111 1111 (4095) 1111 1111 1110 (4094) 0010 0000 0011 (2051) 0010 0000 0010 (2050) 0010 0000 0001 (2049) 0010 0000 0000 (2048) 0001 1111 1111 (2047) 0001 1111 1110 (2046) 0001 1111 1101 (2045) 0000 0000 0001 (1) 0000 0000 0000 (0) Voltage Level 0 VR-V– VR+ R-V+R- 4096 2048 * (V– V)R+ R-4096 4095 * (V– V)R+ R-4096 VR+ (V – V)INHINL + + R- R- V V  2011-2017 Microchip Technology Inc. DS30009995E-page 221

PIC24FV32KA304 FAMILY 22.4 Buffer Data Formats conversions 11 bits wide. The signed decimal format yields 12-bit and 10-bit values, respectively. The sign bit The A/D conversions are fully differential 12-bit values (bit12 or bit 10) is sign-extended to fill the buffer. The when MODE12 = 1 (AD1CON1<10>) and 10-bit values FORM<1:0> bits (AD1CON1<9:8>) select the format. when MODE12 = 0. When absolute fractional or abso- Figure22-4 and Figure22-5 show the data output lute integer formats are used, the results are 12 or formats that can be selected. Table22-1 through 10bits wide, respectively. When signed decimal format- Table22-4 show the numerical equivalents for the ting is used, the conversion also includes a sign bit, various conversion result codes. making 12-bit conversions 13 bits wide, and 10-bit FIGURE 22-4: A/D OUTPUT DATA FORMATS (12-BIT) RAM Contents: d11 d10 d09 d08 d07 d06 d05 d04 d03 d02 d01 d00 Read to Bus: Integer 0 0 0 0 d11 d10 d09 d08 d07 d06 d05 d04 d03 d02 d01 d00 Signed Integer s0 s0 s0 s0 d11 d10 d09 d08 d07 d06 d05 d04 d03 d02 d01 d00 Fractional (1.15) d11 d10 d09 d08 d07 d06 d05 d04 d03 d02 d01 d00 0 0 0 0 Signed Fractional (1.15) s0 d11 d10 d09 d08 d07 d06 d05 d04 d03 d02 d01 d00 0 0 0 TABLE 22-1: NUMERICAL EQUIVALENTS OF VARIOUS RESULT CODES: 12-BIT INTEGER FORMATS 12-Bit Differential 16-Bit Integer Format/ 16-Bit Signed Integer Format/ VIN/VREF Output Code Equivalent Decimal Value Equivalent Decimal Value (13-bit result) +4095/4096 0 1111 1111 1111 0000 1111 1111 1111 +4095 0000 1111 1111 1111 +4095 +4094/4096 0 1111 1111 1110 0000 1111 1111 1110 +4094 0000 1111 1111 1110 +4094  +1/4096 0 1000 0000 0001 0000 0000 0000 0001 +1 0000 0000 0000 0001 +1 0/4096 0 0000 0000 0000 0000 0000 0000 0000 0 0000 0000 0000 0000 0 -1/4096 1 0111 1111 1111 0000 0000 0000 0000 0 1111 1111 1111 1111 -1  -4095/4096 1 0000 0000 0001 0000 0000 0000 0000 0 1111 0000 0000 0001 -4095 -4096/4096 1 0000 0000 0000 0000 0000 0000 0000 0 1111 0000 0000 0000 -4096 DS30009995E-page 222  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY TABLE 22-2: NUMERICAL EQUIVALENTS OF VARIOUS RESULT CODES: 12-BIT FRACTIONAL FORMATS 12-Bit 16-Bit Fractional Format/ 16-Bit Signed Fractional Format/ VIN/VREF Output Code Equivalent Decimal Value Equivalent Decimal Value +4095/4096 0 1111 1111 1111 1111 1111 1111 0000 0.999 0111 1111 1111 1000 0.999 +4094/4096 0 1111 1111 1110 1111 1111 1110 0000 0.998 0111 1111 1110 1000 0.998  +1/4096 0 0000 0000 0001 0000 0000 0001 0000 0.001 0000 0000 0000 1000 0.001 0/4096 0 0000 0000 0000 0000 0000 0000 0000 0.000 0000 0000 0000 0000 0.000 -1/4096 1 0111 1111 1111 0000 0000 0000 0000 0.000 1111 1111 1111 1000 -0.001  -4095/4096 1 0000 0000 0001 0000 0000 0000 0000 0.000 1000 0000 0000 1000 -0.999 -4096/4096 1 0000 0000 0000 0000 0000 0000 0000 0.000 1000 0000 0000 0000 -1.000 FIGURE 22-5: A/D OUTPUT DATA FORMATS (10-BIT) RAM Contents: d09 d08 d07 d06 d05 d04 d03 d02 d01 d00 Read to Bus: Integer 0 0 0 0 0 0 d09 d08 d07 d06 d05 d04 d03 d02 d01 d00 Signed Integer s0 s0 s0 s0 s0 s0 d09 d08 d07 d06 d05 d04 d03 d02 d01 d00 Fractional (1.15) d09 d08 d07 d06 d05 d04 d03 d02 d01 d00 0 0 0 0 0 0 Signed Fractional (1.15) s0 d09 d08 d07 d06 d05 d04 d03 d02 d01 d00 0 0 0 0 0 TABLE 22-3: NUMERICAL EQUIVALENTS OF VARIOUS RESULT CODES: 10-BIT INTEGER FORMATS 10-Bit Differential 16-Bit Integer Format/ 16-Bit Signed Integer Format/ VIN/VREF Output Code Equivalent Decimal Value Equivalent Decimal Value (11-bit result) +1023/1024 011 1111 1111 0000 0011 1111 1111 1023 0000 0001 1111 1111 1023 +1022/1024 011 1111 1110 0000 0011 1111 1110 1022 0000 0001 1111 1110 1022  +1/1024 000 0000 0001 0000 0000 0000 0001 1 0000 0000 0000 0001 1 0/1024 000 0000 0000 0000 0000 0000 0000 0 0000 0000 0000 0000 0 -1/1024 101 1111 1111 0000 0000 0000 0000 0 1111 1111 1111 1111 -1  -1023/1024 100 0000 0001 0000 0000 0000 0000 0 1111 1110 0000 0001 -1023 -1024/1024 100 0000 0000 0000 0000 0000 0000 0 1111 1110 0000 0000 -1024  2011-2017 Microchip Technology Inc. DS30009995E-page 223

PIC24FV32KA304 FAMILY TABLE 22-4: NUMERICAL EQUIVALENTS OF VARIOUS RESULT CODES: 10-BIT FRACTIONAL FORMATS 10-Bit Differential 16-Bit Fractional Format/ 16-Bit Signed Fractional Format/ VIN/VREF Output Code Equivalent Decimal Value Equivalent Decimal Value (11-bit result) +1023/1024 011 1111 1111 1111 1111 1100 0000 0.999 0111 1111 1110 0000 0.999 +1022/1024 011 1111 1110 1111 1111 1000 0000 0.998 0111 1111 1000 0000 0.998  +1/1024 000 0000 0001 0000 0000 0100 0000 0.001 0000 0000 0010 0000 0.001 0/1024 000 0000 0000 0000 0000 0000 0000 0.000 0000 0000 0000 0000 0.000 -1/1024 101 1111 1111 0000 0000 0000 0000 0.000 1111 1111 1110 0000 -0.001  -1023/1024 100 0000 0001 0000 0000 0000 0000 0.000 1000 0000 0010 0000 -0.999 -1024/1024 100 0000 0000 0000 0000 0000 0000 0.000 1000 0000 0000 0000 -1.000 DS30009995E-page 224  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 23.0 COMPARATOR MODULE The comparator outputs may be directly connected to the CxOUT pins. When the respective COE equals ‘1’, Note: This data sheet summarizes the features the I/O pad logic makes the unsynchronized output of of this group of PIC24F devices. It is not the comparator available on the pin. intended to be a comprehensive refer- A simplified block diagram of the module is shown in ence source. For more information on the Figure23-1. Diagrams of the possible individual Comparator module, refer to the comparator configurations are shown in Figure23-2. “dsPIC33/PIC24 Family Reference Man- ual”, “Scalable Comparator Module” Each comparator has its own control register, (DS39734). CMxCON (Register23-1), for enabling and configuring its operation. The output and event status of all three The comparator module provides three dual input comparators is provided in the CMSTAT register comparators. The inputs to the comparator can be (Register23-2). configured to use any one of four external analog inputs, as well as a voltage reference input from either the internal band gap reference, divided by 2 (VBG/2), or the comparator voltage reference generator. FIGURE 23-1: COMPARATOR x MODULE BLOCK DIAGRAM CCH<1:0> CREF EVPOL<1:0> Trigger/Interrupt CEVT CXINB CPOL Logic COE Input VIN- CXINC Select C1 Logic VIN+ CXIND C1OUT Pin COUT VBG/2 EVPOL<1:0> Trigger/Interrupt CEVT Logic CPOL COE VIN- C2 VIN+ C2OUT Pin COUT EVPOL<1:0> Trigger/Interrupt CEVT Logic CPOL COE CXINA VIN- C3 VIN+ CVREF C3OUT Pin COUT  2011-2017 Microchip Technology Inc. DS30009995E-page 225

PIC24FV32KA304 FAMILY FIGURE 23-2: INDIVIDUAL COMPARATOR CONFIGURATIONS Comparator Off CON=0, CREF=x, CCH<1:0>=xx COE VIN- – Cx VIN+ Off (Read as ‘0’) CxOUT Pin Comparator CxINB > CxINA Compare Comparator CxINC > CxINA Compare CON=1, CREF=0, CCH<1:0>=00 CON=1, CREF=0, CCH<1:0>=01 COE COE CXINB VIN- – CXINC VIN- – Cx Cx VIN+ VIN+ CXINA CxOUT CXINA CxOUT Pin Pin Comparator CxIND > CxINA Compare Comparator VBG > CxINA Compare CON=1, CREF=0, CCH<1:0>=10 CON=1, CREF=0, CCH<1:0>=11 COE COE CXIND VIN- – VBG/2 VIN- – Cx Cx VIN+ VIN+ CXINA CxOUT CXINA CxOUT Pin Pin Comparator CxINB > CVREF Compare Comparator CxINC > CVREF Compare CON=1, CREF=1, CCH<1:0>=00 CON=1, CREF=1, CCH<1:0>=01 COE COE CXINB VIN- – CXINC VIN- – Cx Cx VIN+ VIN+ CVREF CxOUT CVREF CxOUT Pin Pin Comparator CxIND > CVREF Compare Comparator VBG > CVREF Compare CON=1, CREF=1, CCH<1:0>=10 CON=1, CREF=1, CCH<1:0>=11 COE COE CXIND VIN- – VBG/2 VIN- – Cx Cx VIN+ VIN+ CVREF CxOUT CVREF CxOUT Pin Pin DS30009995E-page 226  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY R EGISTER 23-1: CMxCON: COMPARATOR x CONTROL REGISTERS R/W-0 R/W-0 R/W-0 R/W-0 U-0 U-0 R/W-0 R-0 CON COE CPOL CLPWR — — CEVT COUT bit 15 bit 8 R/W-0 R/W-0 U-0 R/W-0 U-0 U-0 R/W-0 R/W-0 EVPOL1 EVPOL0 — CREF — — CCH1 CCH0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 CON: Comparator x Enable bit 1 = Comparator is enabled 0 = Comparator is disabled bit 14 COE: Comparator x Output Enable bit 1 = Comparator output is present on the CxOUT pin 0 = Comparator output is internal only bit 13 CPOL: Comparator x Output Polarity Select bit 1 = Comparator output is inverted 0 = Comparator output is not inverted bit 12 CLPWR: Comparator x Low-Power Mode Select bit 1 = Comparator operates in Low-Power mode, transient response is reduced 0 = Comparator does not operate in Low-Power mode bit 11-10 Unimplemented: Read as ‘0’ bit 9 CEVT: Comparator x Event bit 1 = Comparator event defined by EVPOL<1:0> has occurred; subsequent triggers and interrupts are disabled until the bit is cleared 0 = Comparator event has not occurred bit 8 COUT: Comparator x Output bit When CPOL = 0: 1 = VIN+ > VIN- 0 = VIN+ < VIN- When CPOL = 1: 1 = VIN+ < VIN- 0 = VIN+ > VIN- bit 7-6 EVPOL<1:0>: Trigger/Event/Interrupt Polarity Select bits 11 = Trigger/event/interrupt is generated on any change of the comparator output (while CEVT=0) 10 = Trigger/event/interrupt is generated on the transition of the comparator output: If CPOL = 0 (non-inverted polarity): High-to-low transition only. If CPOL = 1 (inverted polarity): Low-to-high transition only. 01 = Trigger/event/interrupt is generated on the transition of the comparator output If CPOL = 0 (non-inverted polarity): Low-to-high transition only. If CPOL = 1 (inverted polarity): High-to-low transition only. 00 = Trigger/event/interrupt generation is disabled bit 5 Unimplemented: Read as ‘0’  2011-2017 Microchip Technology Inc. DS30009995E-page 227

PIC24FV32KA304 FAMILY REGISTER 23-1: CMxCON: COMPARATOR x CONTROL REGISTERS (CONTINUED) bit 4 CREF: Comparator x Reference Select bits (non-inverting input) 1 = Non-inverting input connects to the internal CVREF voltage 0 = Non-inverting input connects to the CxINA pin bit 3-2 Unimplemented: Read as ‘0’ bit 1-0 CCH<1:0>: Comparator x Channel Select bits 11 = Inverting input of the comparator connects to VBG 10 = Inverting input of the comparator connects to the CxIND pin 01 = Inverting input of the comparator connects to the CxINC pin 00 = Inverting input of the comparator connects to the CxINB pin REGISTER 23-2: CMSTAT: COMPARATOR x MODULE STATUS REGISTER R/W-0 U-0 U-0 U-0 U-0 R-0, HSC R-0, HSC R-0, HSC CMIDL — — — — C3EVT C2EVT C1EVT bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 R-0, HSC R-0, HSC R-0, HSC — — — — — C3OUT C2OUT C1OUT bit 7 bit 0 Legend: HSC = Hardware Settable/Clearable bit R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 CMIDL: Comparator x Stop in Idle Mode bit 1 = Comparator interrupts are disabled in Idle mode; enabled comparators remain operational 0 = Continues operation of all enabled comparators in Idle mode bit 14-11 Unimplemented: Read as ‘0’ bit 10 C3EVT: Comparator 3 Event Status bit (read-only) Shows the current event status of Comparator 3 (CM3CON<9>). bit 9 C2EVT: Comparator 2 Event Status bit (read-only) Shows the current event status of Comparator 2 (CM2CON<9>). bit 8 C1EVT: Comparator 1 Event Status bit (read-only) Shows the current event status of Comparator 1 (CM1CON<9>). bit 7-3 Unimplemented: Read as ‘0’ bit 2 C3OUT: Comparator 3 Output Status bit (read-only) Shows the current output of Comparator 3 (CM3CON<8>). bit 1 C2OUT: Comparator 2 Output Status bit (read-only) Shows the current output of Comparator 2 (CM2CON<8>). bit 0 C1OUT: Comparator 1 Output Status bit (read-only) Shows the current output of Comparator 1 (CM1CON<8>). DS30009995E-page 228  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 24.0 COMPARATOR VOLTAGE 24.1 Configuring the Comparator REFERENCE Voltage Reference The comparator voltage reference module is controlled Note: This data sheet summarizes the features of through the CVRCON register (Register24-1). The this group of PIC24F devices. It is not comparator voltage reference provides a range of intended to be a comprehensive reference output voltages, with 32 distinct levels. source. For more information on the Comparator Voltage Reference, refer to the The comparator voltage reference supply voltage can “dsPIC33/PIC24 Family Reference Man- come from either VDD and VSS or the external VREF+ ual”, “Comparator Voltage Reference and VREF-. The voltage source is selected by the Module” (DS39709). CVRSS bit (CVRCON<5>). The settling time of the comparator voltage reference must be considered when changing the CVREF output. FIGURE 24-1: COMPARATOR VOLTAGE REFERENCE BLOCK DIAGRAM CVRSS = 1 VREF+ AVDD CVRSS = 0 8R CVR<3:0> CVREN R R R R X U 32 Steps M 1 CVREF o- 2-t 3 R R R 8R CVRSS = 1 VREF- CVRSS = 0 AVSS  2011-2017 Microchip Technology Inc. DS30009995E-page 229

PIC24FV32KA304 FAMILY REGISTER 24-1: CVRCON: COMPARATOR VOLTAGE REFERENCE CONTROL REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CVREN CVROE CVRSS CVR4 CVR3 CVR2 CVR1 CVR0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-8 Unimplemented: Read as ‘0’ bit 7 CVREN: Comparator Voltage Reference Enable bit 1 = CVREF circuit is powered on 0 = CVREF circuit is powered down bit 6 CVROE: Comparator VREF Output Enable bit 1 = CVREF voltage level is output on the CVREF pin 0 = CVREF voltage level is disconnected from the CVREF pin bit 5 CVRSS: Comparator VREF Source Selection bit 1 = Comparator reference source, CVRSRC = VREF+ – VREF- 0 = Comparator reference source, CVRSRC = AVDD – AVSS bit 4-0 CVR<4:0>: Comparator VREF Value Selection 0 ≤ CVR<4:0> ≤ 31 bits When CVRSS = 1: CVREF = (VREF-) + (CVR<4:0>/32) • (VREF+ – VREF-) When CVRSS = 0: CVREF = (AVSS) + (CVR<4:0>/32) • (AVDD – AVSS) DS30009995E-page 230  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 25.0 CHARGE TIME 25.1 Measuring Capacitance MEASUREMENT UNIT (CTMU) The CTMU module measures capacitance by generating an output pulse, with a width equal to the Note: This data sheet summarizes the features of time between edge events, on two separate input this group of PIC24F devices. It is not channels. The pulse edge events to both input intended to be a comprehensive reference channels can be selected from several internal source. For more information on the peripheral modules (OC1, Timer1, any input capture or Charge Measurement Unit, refer to the comparator module) and up to 13 external pins “dsPIC33/PIC24 Family Reference Man- (CTED1 through CTED13). This pulse is used with the ual”, “Charge Time Measurement Unit module’s precision current source to calculate (CTMU) and CTMU Operation with capacitance according to the relationship: Threshold Detect” (DS30009743). The Charge Time Measurement Unit (CTMU) is a EQUATION 25-1: flexible analog module that provides charge dV measurement, accurate differential time measurement I = C------- dT between pulse sources and asynchronous pulse generation. Its key features include: For capacitance measurements, the A/D Converter • Thirteen external edge input trigger sources samples an external capacitor (CAPP) on one of its input channels after the CTMU output’s pulse. A Preci- • Polarity control for each edge source sion Resistor (RPR) provides current source calibration • Control of edge sequence on a second A/D channel. After the pulse ends, the • Control of response to edge levels or edge converter determines the voltage on the capacitor. The transitions actual calculation of capacitance is performed in • Time measurement resolution of onenanosecond software by the application. • Accurate current source suitable for capacitive Figure25-1 illustrates the external connections used measurement for capacitance measurements, and how the CTMU Together with other on-chip analog modules, the CTMU and A/D modules are related in this application. This can be used to precisely measure time, measure example also shows the edge events coming from capacitance, measure relative changes in capacitance Timer1, but other configurations using external edge or generate output pulses that are independent of the sources are possible. A detailed discussion on measur- system clock. The CTMU module is ideal for interfacing ing capacitance and time with the CTMU module is with capacitive-based touch sensors. provided in the “dsPIC33/PIC24 Family Reference The CTMU is controlled through three registers: Manual”. CTMUCON1, CTMUCON2 and CTMUICON. CTMUCON1 enables the module and controls the mode of operation of the CTMU, as well as controlling edge sequencing. CTMUCON2 controls edge source selec- tion and edge source polarity selection. The CTMUICON register selects the current range of current source and trims the current.  2011-2017 Microchip Technology Inc. DS30009995E-page 231

PIC24FV32KA304 FAMILY FIGURE 25-1: TYPICAL CONNECTIONS AND INTERNAL CONFIGURATION FOR CAPACITANCE MEASUREMENT PIC24F Device Timer1 CTMU EDG1 Current Source EDG2 Output Pulse ANx A/D Converter ANy CAPP RPR 25.2 Measuring Time time measurements, and how the CTMU and A/D modules are related in this application. This example Time measurements on the pulse width can be similarly also shows both edge events coming from the external performed using the A/D module’s Internal Capacitor CTEDx pins, but other configurations using internal (CAD) and a precision resistor for current calibration. edge sources are possible. Figure25-2 displays the external connections used for FIGURE 25-2: TYPICAL CONNECTIONS AND INTERNAL CONFIGURATION FOR TIME MEASUREMENT PIC24F Device CTMU CTEDX EDG1 Current Source CTEDX EDG2 Output Pulse A/D Converter ANx CAD RPR DS30009995E-page 232  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 25.3 Pulse Generation and Delay When the voltage on CDELAY equals CVREF, CTPLS goes low. With Comparator 2 configured as the second The CTMU module can also generate an output pulse edge, this stops the CTMU from charging. In this state with edges that are not synchronous with the device’s event, the CTMU automatically connects to ground. system clock. More specifically, it can generate a pulse The IDISSEN bit doesn’t need to be set and cleared with a programmable delay from an edge event input to before the next CTPLS cycle. the module. Figure25-3 illustrates the external connections for When the module is configured for pulse generation pulse generation, as well as the relationship of the delay by setting the TGEN bit (CTMUCON<12>), the different analog modules required. While CTED1 is internal current source is connected to the B input of shown as the input pulse source, other options are Comparator 2. A capacitor (CDELAY) is connected to available. A detailed discussion on pulse generation the Comparator 2 pin, C2INB, and the Comparator with the CTMU module is provided in the “dsPIC33/ Voltage Reference, CVREF, is connected to C2INA. PIC24 Family Reference Manual”. CVREF is then configured for a specific trip point. The module begins to charge CDELAY when an edge event is detected. While CVREF is greater than the voltage on CDELAY, CTPLS is high. FIGURE 25-3: TYPICAL CONNECTIONS AND INTERNAL CONFIGURATION FOR PULSE DELAY GENERATION PIC24F Device CTMU VDD D Q CTPLS EDG1 EDG2 EDG1 CTED1 CK Q Current R Source Comparator EDG2 C2INB – C2 CDELAY CVREF  2011-2017 Microchip Technology Inc. DS30009995E-page 233

PIC24FV32KA304 FAMILY R EGISTER 25-1: CTMUCON1: CTMU CONTROL REGISTER 1 R/W-0 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 CTMUEN — CTMUSIDL TGEN EDGEN EDGSEQEN IDISSEN CTTRIG bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 CTMUEN: CTMU Enable bit 1 = Module is enabled 0 = Module is disabled bit 14 Unimplemented: Read as ‘0’ bit 13 CTMUSIDL: CTMU Stop in Idle Mode bit 1 = Discontinues module operation when device enters Idle mode 0 = Continues module operation in Idle mode bit 12 TGEN: Time Generation Enable bit 1 = Enables edge delay generation 0 = Disables edge delay generation bit 11 EDGEN: Edge Enable bit 1 = Edges are not blocked 0 = Edges are blocked bit 10 EDGSEQEN: Edge Sequence Enable bit 1 = Edge 1 event must occur before Edge 2 event can occur 0 = No edge sequence is needed bit 9 IDISSEN: Analog Current Source Control bit 1 = Analog current source output is grounded 0 = Analog current source output is not grounded bit 8 CTTRIG: CTMU Trigger Control bit 1 = Trigger output is enabled 0 = Trigger output is disabled bit 7-0 Unimplemented: Read as ‘0’ DS30009995E-page 234  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY R EGISTER 25-2: CTMUCON2: CTMU CONTROL REGISTER 2 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 EDG1MOD EDG1POL EDG1SEL3 EDG1SEL2 EDG1SEL1 EDG1SEL0 EDG2STAT EDG1STAT bit 15 bit 8 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 U-0 U-0 EDG2MOD EDG2POL EDG2SEL3 EDG2SEL2 EDG2SEL1 EDG2SEL0 — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15 EDG1MOD: Edge 1 Edge-Sensitive Select bit 1 = Input is edge-sensitive 0 = Input is level-sensitive bit 14 EDG1POL: Edge 1 Polarity Select bit 1 = Edge 1 is programmed for a positive edge response 0 = Edge 1 is programmed for a negative edge response bit 13-10 EDG1SEL<3:0>: Edge 1 Source Select bits 1111 = Edge 1 source is Comparator 3 output 1110 = Edge 1 source is Comparator 2 output 1101 = Edge 1 source is Comparator 1 output 1100 = Edge 1 source is IC3 1011 = Edge 1 source is IC2 1010 = Edge 1 source is IC1 1001 = Edge 1 source is CTED8 1000 = Edge 1 source is CTED7 0111 = Edge 1 source is CTED6 0110 = Edge 1 source is CTED5 0101 = Edge 1 source is CTED4 0100 = Edge 1 source is CTED3(1) 0011 = Edge 1 source is CTED1 0010 = Edge 1 source is CTED2 0001 = Edge 1 source is OC1 0000 = Edge 1 source is Timer1 bit 9 EDG2STAT: Edge 2 Status bit Indicates the status of Edge 2 and can be written to control the current source. 1 = Edge 2 has occurred 0 = Edge 2 has not occurred bit 8 EDG1STAT: Edge 1 Status bit Indicates the status of Edge 1 and can be written to control the current source. 1 = Edge 1 has occurred 0 = Edge 1 has not occurred bit 7 EDG2MOD: Edge 2 Edge-Sensitive Select bit 1 = Input is edge-sensitive 0 = Input is level-sensitive bit 6 EDG2POL: Edge 2 Polarity Select bit 1 = Edge 2 is programmed for a positive edge 0 = Edge 2 is programmed for a negative edge Note 1: Edge sources, CTED3 and CTED11, are not available on PIC24FV32KA301 devices.  2011-2017 Microchip Technology Inc. DS30009995E-page 235

PIC24FV32KA304 FAMILY REGISTER 25-2: CTMUCON2: CTMU CONTROL REGISTER 2 (CONTINUED) bit 5-2 EDG2SEL<3:0>: Edge 2 Source Select bits 1111 = Edge 2 source is Comparator 3 output 1110 = Edge 2 source is Comparator 2 output 1101 = Edge 2 source is Comparator 1 output 1100 = Unimplemented; do not use 1011 = Edge 2 source is IC3 1010 = Edge 2 source is IC2 1001 = Edge 2 source is IC1 1000 = Edge 2 source is CTED13(1) 0111 = Edge 2 source is CTED12(1) 0110 = Edge 2 source is CTED11(1) 0101 = Edge 2 source is CTED10 0100 = Edge 2 source is CTED9 0011 = Edge 2 source is CTED1 0010 = Edge 2 source is CTED2 0001 = Edge 2 source is OC1 0000 = Edge 2 source is Timer1 bit 1-0 Unimplemented: Read as ‘0’ Note 1: Edge sources, CTED3 and CTED11, are not available on PIC24FV32KA301 devices. DS30009995E-page 236  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 25-3: CTMUICON: CTMU CURRENT CONTROL REGISTER R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ITRIM5 ITRIM4 ITRIM3 ITRIM2 ITRIM1 ITRIM0 IRNG1 IRNG0 bit 15 bit 8 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 15-10 ITRIM<5:0>: Current Source Trim bits 011111 = Maximum positive change from nominal current 011110 • • • 000001 = Minimum positive change from nominal current 000000 = Nominal current output specified by IRNG<1:0> 111111 = Minimum negative change from nominal current • • • 100010 100001 = Maximum negative change from nominal current bit 9-8 IRNG<1:0>: Current Source Range Select bits 11 = 100 × Base Current 10 = 10 × Base Current 01 = Base Current Level (0.55 µA nominal) 00 = 1000 × Base Current bit 7-0 Unimplemented: Read as ‘0’  2011-2017 Microchip Technology Inc. DS30009995E-page 237

PIC24FV32KA304 FAMILY NOTES: DS30009995E-page 238  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 26.0 SPECIAL FEATURES 26.1 Configuration Bits Note: This data sheet summarizes the features of The Configuration bits can be programmed (read as this group of PIC24F devices. It is not ‘0’), or left unprogrammed (read as ‘1’), to select vari- intended to be a comprehensive reference ous device configurations. These bits are mapped, source. For more information on the Watch- starting at program memory location, F80000h. A dog Timer, High-Level Device Integration complete list of Configuration register locations is and Programming Diagnostics, refer to the provided in Table26-1. A detailed explanation of the individual sections of the “dsPIC33/PIC24 various bit functions is provided in Register26-1 Family Reference Manual” provided below: through Register26-8. • “Watchdog Timer (WDT)” (DS39697) The address, F80000h, is beyond the user program memory space. In fact, it belongs to the configuration • “High-Level Integration with memory space (800000h-FFFFFFh), which can only be Programmable High/Low-Voltage accessed using Table Reads and Table Writes. Detect (HLVD)” (DS39725) • Section 33. “Programming and TABLE 26-1: CONFIGURATION REGISTERS Diagnostics” (DS39716) LOCATIONS PIC24FV32KA304 family devices include several Configuration features intended to maximize application flexibility and Register Address reliability, and minimize cost through elimination of external components. These are: FBS F80000 FGS F80004 • Flexible Configuration FOSCSEL F80006 • Watchdog Timer (WDT) FOSC F80008 • Code Protection FWDT F8000A • In-Circuit Serial Programming™ (ICSP™) FPOR F8000C • In-Circuit Emulation FICD F8000E FDS F80010 REGISTER 26-1: FBS: BOOT SEGMENT CONFIGURATION REGISTER U-0 U-0 U-0 U-0 R/W-1 R/W-1 R/W-1 R/W-1 — — — — BSS2 BSS1 BSS0 BWRP bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7-4 Unimplemented: Read as ‘0’ bit 3-1 BSS<2:0>: Boot Segment Program Flash Code Protection bits 111 = No boot program Flash segment 011 = Reserved 110 = Standard security, boot program Flash segment starts at 200h, ends at 000AFEh 010 = High-security boot program Flash segment starts at 200h, ends at 000AFEh 101 = Standard security, boot program Flash segment starts at 200h, ends at 0015FEh(1) 001 = High-security, boot program Flash segment starts at 200h, ends at 0015FEh(1) 100 = Standard security; boot program Flash segment starts at 200h, ends at 002BFEh(1) 000 = High-security; boot program Flash segment starts at 200h, ends at 002BFEh(1) bit 0 BWRP: Boot Segment Program Flash Write Protection bit 1 = Boot Segment may be written 0 = Boot Segment is write-protected Note 1: This selection should not be used in PIC24FV16KA3XX devices.  2011-2017 Microchip Technology Inc. DS30009995E-page 239

PIC24FV32KA304 FAMILY REGISTER 26-2: FGS: GENERAL SEGMENT CONFIGURATION REGISTER U-0 U-0 U-0 U-0 U-0 U-0 R/C-1 R/C-1 — — — — — — GSS0 GWRP bit 7 bit 0 Legend: R = Readable bit C = Clearable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7-2 Unimplemented: Read as ‘0’ bit 1 GSS0: General Segment Code Flash Code Protection bit 1 = No protection 0 = Standard security is enabled bit 0 GWRP: General Segment Code Flash Write Protection bit 1 = General Segment may be written 0 = General Segment is write-protected REGISTER 26-3: FOSCSEL: OSCILLATOR SELECTION CONFIGURATION REGISTER R/P-1 R/P-1 R/P-1 U-0 U-0 R/P-1 R/P-1 R/P-1 IESO LPRCSEL SOSCSRC — — FNOSC2 FNOSC1 FNOSC0 bit 7 bit 0 Legend: R = Readable bit P = Programmable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 IESO: Internal External Switchover bit 1 = Internal External Switchover mode is enabled (Two-Speed Start-up is enabled) 0 = Internal External Switchover mode is disabled (Two-Speed Start-up is disabled) bit 6 LPRCSEL: Internal LPRC Oscillator Power Select bit 1 = High-Power/High-Accuracy mode 0 = Low-Power/Low-Accuracy mode bit 5 SOSCSRC: Secondary Oscillator Clock Source Configuration bit 1 = SOSC analog crystal function is available on the SOSCI/SOSCO pins 0 = SOSC crystal is disabled; digital SCLKI function is selected on the SOSCO pin bit 4-3 Unimplemented: Read as ‘0’ bit 2-0 FNOSC<2:0>: Oscillator Selection bits 000 = Fast RC Oscillator (FRC) 001 = Fast RC Oscillator with Divide-by-N with PLL module (FRCDIV+PLL) 010 = Primary Oscillator (XT, HS, EC) 011 = Primary Oscillator with PLL module (HS+PLL, EC+PLL) 100 = Secondary Oscillator (SOSC) 101 = Low-Power RC Oscillator (LPRC) 110 = 500 kHz Low-Power FRC Oscillator with Divide-by-N (LPFRCDIV) 111 = 8 MHz FRC Oscillator with Divide-by-N (FRCDIV) DS30009995E-page 240  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 26-4: FOSC: OSCILLATOR CONFIGURATION REGISTER R/P-1 R/P-1 R/P-1 R/P-1 R/P-1 R/P-1 R/P-1 R/P-1 FCKSM1 FCKSM0 SOSCSEL POSCFREQ1 POSCFREQ0 OSCIOFNC POSCMD1 POSCMD0 bit 7 bit 0 Legend: R = Readable bit P = Programmable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7-6 FCKSM<1:0>: Clock Switching and Fail-Safe Clock Monitor Selection Configuration bits 1x = Clock switching is disabled, Fail-Safe Clock Monitor is disabled 01 = Clock switching is enabled, Fail-Safe Clock Monitor is disabled 00 = Clock switching is enabled, Fail-Safe Clock Monitor is enabled bit 5 SOSCSEL: Secondary Oscillator Power Selection Configuration bit 1 = Secondary oscillator is configured for high-power operation 0 = Secondary oscillator is configured for low-power operation bit 4-3 POSCFREQ<1:0>: Primary Oscillator Frequency Range Configuration bits 11 = Primary oscillator/external clock input frequency is greater than 8 MHz 10 = Primary oscillator/external clock input frequency is between 100 kHz and 8 MHz 01 = Primary oscillator/external clock input frequency is less than 100 kHz 00 = Reserved; do not use bit 2 OSCIOFNC: CLKO Enable Configuration bit 1 = CLKO output signal is active on the OSCO pin; primary oscillator must be disabled or configured for the External Clock mode (EC) for the CLKO to be active (POSCMD<1:0> = 11 or 00) 0 = CLKO output is disabled bit 1-0 POSCMD<1:0>: Primary Oscillator Configuration bits 11 = Primary Oscillator mode is disabled 10 = HS Oscillator mode is selected 01 = XT Oscillator mode is selected 00 = External Clock mode is selected  2011-2017 Microchip Technology Inc. DS30009995E-page 241

PIC24FV32KA304 FAMILY REGISTER 26-5: FWDT: WATCHDOG TIMER CONFIGURATION REGISTER R/P-1 R/P-1 R/P-1 R/P-1 R/P-1 R/P-1 R/P-1 R/P-1 FWDTEN1 WINDIS FWDTEN0 FWPSA WDTPS3 WDTPS2 WDTPS1 WDTPS0 bit 7 bit 0 Legend: R = Readable bit P = Programmable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7,5 FWDTEN<1:0>: Watchdog Timer Enable bits 11 = WDT is enabled in hardware 10 = WDT is controlled with the SWDTEN bit setting 01 = WDT is enabled only while device is active; WDT is disabled in Sleep, SWDTEN bit is disabled 00 = WDT is disabled in hardware; SWDTEN bit is disabled bit 6 WINDIS: Windowed Watchdog Timer Disable bit 1 = Standard WDT is selected; windowed WDT is disabled 0 = Windowed WDT is enabled; note that executing a CLRWDT instruction while the WDT is disabled in hardware and software (FWDTEN<1:0> = 00 and SWDTEN (RCON<5>) = 0) will not cause a device Reset bit 4 FWPSA: WDT Prescaler bit 1 = WDT prescaler ratio of 1:128 0 = WDT prescaler ratio of 1:32 bit 3-0 WDTPS<3:0>: Watchdog Timer Postscale Select bits 1111 = 1:32,768 1110 = 1:16,384 1101 = 1:8,192 1100 = 1:4,096 1011 = 1:2,048 1010 = 1:1,024 1001 = 1:512 1000 = 1:256 0111 = 1:128 0110 = 1:64 0101 = 1:32 0100 = 1:16 0011 = 1:8 0010 = 1:4 0001 = 1:2 0000 = 1:1 DS30009995E-page 242  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 26-6: FPOR: RESET CONFIGURATION REGISTER R/P-1 R/P-1 R/P-1 R/P-1 R/P-1 R/P-1 R/P-1 R/P-1 MCLRE(2) BORV1(3) BORV0(3) I2C1SEL(1) PWRTEN RETCFG(1) BOREN1 BOREN0 bit 7 bit 0 Legend: R = Readable bit P = Programmable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 MCLRE: MCLR Pin Enable bit(2) 1 = MCLR pin is enabled; RA5 input pin is disabled 0 = RA5 input pin is enabled; MCLR is disabled bit 6-5 BORV<1:0>: Brown-out Reset Enable bits(3) 11 = Brown-out Reset is set to the lowest voltage 10 = Brown-out Reset 01 = Brown-out Reset is set to the highest voltage 00 = Downside protection on POR is enabled – “zero power” is selected bit 4 I2C1SEL: Alternate I2C1 Pin Mapping bit(1) 1 = Default location for SCL1/SDA1 pins 0 = Alternate location for SCL1/SDA1 pins bit 3 PWRTEN: Power-up Timer Enable bit 1 = PWRT is enabled 0 = PWRT is disabled bit 2 RETCFG: Retention Regulator Configuration bit(1) 1 = Retention Regulator is not available 0 = Retention Regulator is available and controlled by the RETEN bit (RCON<12>) during Sleep bit 1-0 BOREN<1:0>: Brown-out Reset Enable bits 11 = Brown-out Reset is enabled in hardware; SBOREN bit is disabled 10 = Brown-out Reset is enabled only while device is active and disabled in Sleep; SBOREN bit is disabled 01 = Brown-out Reset is controlled with the SBOREN bit setting 00 = Brown-out Reset is disabled in hardware; SBOREN bit is disabled Note 1: This setting only applies to the “FV” devices. This bit is reserved and should be maintained as ‘1’ on “F” devices. 2: The MCLRE fuse can only be changed when using the VPP-based ICSP™ mode entry. This prevents a user from accidentally locking out the device from the low-voltage test entry. 3: Refer to Section29.0 “Electrical Characteristics” for BOR voltages.  2011-2017 Microchip Technology Inc. DS30009995E-page 243

PIC24FV32KA304 FAMILY REGISTER 26-7: FICD: IN-CIRCUIT DEBUGGER CONFIGURATION REGISTER R/P-1 U-0 U-0 U-0 U-0 U-0 R/P-1 R/P-1 DEBUG — — — — — FICD1 FICD0 bit 7 bit 0 Legend: R = Readable bit P = Programmable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 DEBUG: Background Debugger Enable bit 1 = Background debugger is disabled 0 = Background debugger functions are enabled bit 6-2 Unimplemented: Read as ‘0’ bit 1-0 FICD<1:0:>: ICD Pin Select bits 11 = PGEC1/PGED1 are used for programming and debugging the device 10 = PGEC2/PGED2 are used for programming and debugging the device 01 = PGEC3/PGED3 are used for programming and debugging the device 00 = Reserved; do not use DS30009995E-page 244  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 26-8: FDS: DEEP SLEEP CONFIGURATION REGISTER R/P-1 R/P-1 U-0 R/P-1 R/P-1 R/P-1 R/P-1 R/P-1 DSWDTEN DSBOREN — DSWDTOSC DSWDTPS3 DSWDTPS2 DSWDTPS1 DSWDTPS0 bit 7 bit 0 Legend: R = Readable bit P = Programmable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7 DSWDTEN: Deep Sleep Watchdog Timer Enable bit 1 = DSWDT is enabled 0 = DSWDT is disabled bit 6 DSBOREN: Deep Sleep/Low-Power BOR Enable bit (does not affect operation in non Deep Sleep modes) 1 = Deep Sleep BOR is enabled in Deep Sleep 0 = Deep Sleep BOR is disabled in Deep Sleep bit 5 Unimplemented: Read as ‘0’ bit 4 DSWDTOSC: DSWDT Reference Clock Select bit 1 = DSWDT uses LPRC as the reference clock 0 = DSWDT uses SOSC as the reference clock bit 3-0 DSWDTPS<3:0>: Deep Sleep Watchdog Timer Postscale Select bits The DSWDT prescaler is 32; this creates an approximate base time unit of 1 ms. 1111 = 1:2,147,483,648 (25.7 days) nominal 1110 = 1:536,870,912 (6.4 days) nominal 1101 = 1:134,217,728 (38.5 hours) nominal 1100 = 1:33,554,432 (9.6 hours) nominal 1011 = 1:8,388,608 (2.4 hours) nominal 1010 = 1:2,097,152 (36 minutes) nominal 1001 = 1:524,288 (9 minutes) nominal 1000 = 1:131,072 (135 seconds) nominal 0111 = 1:32,768 (34 seconds) nominal 0110 = 1:8,192 (8.5 seconds) nominal 0101 = 1:2,048 (2.1 seconds) nominal 0100 = 1:512 (528 ms) nominal 0011 = 1:128 (132 ms) nominal 0010 = 1:32 (33 ms) nominal 0001 = 1:8 (8.3 ms) nominal 0000 = 1:2 (2.1 ms) nominal  2011-2017 Microchip Technology Inc. DS30009995E-page 245

PIC24FV32KA304 FAMILY REGISTER 26-9: DEVID: DEVICE ID REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 23 bit 16 R R R R R R R R FAMID7 FAMID6 FAMID5 FAMID4 FAMID3 FAMID2 FAMID1 FAMID0 bit 15 bit 8 R R R R R R R R DEV7 DEV6 DEV5 DEV4 DEV3 DEV2 DEV1 DEV0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 23-16 Unimplemented: Read as ‘0’ bit 15-8 FAMID<7:0>: Device Family Identifier bits 01000101 = PIC24FV32KA304 family bit 7-0 DEV<7:0>: Individual Device Identifier bits 00010111 = PIC24FV32KA304 00000111 = PIC24FV16KA304 00010011 = PIC24FV32KA302 00000011 = PIC24FV16KA302 00011001 = PIC24FV32KA301 00001001 = PIC24FV16KA301 00010110 = PIC24F32KA304 00000110 = PIC24F16KA304 00010010 = PIC24F32KA302 00000010 = PIC24F16KA302 00011000 = PIC24F32KA301 00001000 = PIC24F16KA301 DS30009995E-page 246  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY REGISTER 26-10: DEVREV: DEVICE REVISION REGISTER U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 23 bit 16 U-0 U-0 U-0 U-0 U-0 U-0 U-0 U-0 — — — — — — — — bit 15 bit 8 U-0 U-0 U-0 U-0 R R R R — — — — REV<3:0> bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 23-4 Unimplemented: Read as ‘0’ bit 3-0 REV<3:0>: Minor Revision Identifier bits  2011-2017 Microchip Technology Inc. DS30009995E-page 247

PIC24FV32KA304 FAMILY 26.2 On-Chip Voltage Regulator FIGURE 26-1: CONNECTIONS FOR THE ON-CHIP REGULATOR All of the PIC24FV32KA304 family devices power their core digital logic at a nominal 3.0V. This may create an Regulator Enabled(1): issue for designs that are required to operate at a higher typical voltage, as high as 5.0V. To simplify sys- 5.0V tem design, all devices in the “FV” family incorporate an PIC24FV32KA304 on-chip regulator that allows the device to run its core VDD logic from VDD. The regulator is always enabled and provides power to VCAP the core from the other VDD pins. A low-ESR capacitor CEFC (such as ceramic) must be connected to the VCAP pin (10F typ) VSS (Figure26-1). This helps to maintain the stability of the regulator. The recommended value for the filter capaci- tor is discussed in Section2.4 “Voltage Regulator Pin (VCAP)”, and in Section29.1 “DC Characteristics”. Note 1: These are typical operating voltages. Refer to Section29.0 “Electrical Characteristics” For “F” devices, the regulator is disabled. Instead, core for the full operating ranges of VDD. logic is powered directly from VDD. This allows the devices to operate at an overall lower allowable voltage range (1.8V-3.6V). 26.3 Watchdog Timer (WDT) 26.2.1 VOLTAGE REGULATOR TRACKING For the PIC24FV32KA304 family of devices, the WDT MODE AND LOW-VOLTAGE is driven by the LPRC oscillator. When the WDT is DETECTION enabled, the clock source is also enabled. For all PIC24FV32KA304 devices, the on-chip regula- The nominal WDT clock source from LPRC is 31 kHz. tor provides a constant voltage of 3.2V nominal to the This feeds a prescaler that can be configured for either digital core logic. The regulator can provide this level 5-bit (divide-by-32) or 7-bit (divide-by-128) operation. from a VDD of about 3.2V, all the way up to the device’s The prescaler is set by the FWPSA Configuration bit. VDDMAX. It does not have the capability to boost VDD With a 31kHz input, the prescaler yields a nominal levels below 3.2V. In order to prevent “brown-out” con- WDT time-out period (TWDT) of 1ms in 5-bit mode or ditions when the voltage drops too low for the regulator, 4ms in 7-bit mode. the regulator enters Tracking mode. In Tracking mode, A variable postscaler divides down the WDT prescaler the regulator output follows VDD with a typical voltage output and allows for a wide range of time-out periods. drop of 150 mV. The postscaler is controlled by the Configuration bits, When the device enters Tracking mode, it is no longer WDTPS<3:0> (FWDT<3:0>), which allow the selection possible to operate at full speed. To provide information of a total of 16 settings, from 1:1 to 1:32,768. Using the about when the device enters Tracking mode, the prescaler and postscaler time-out periods, ranging on-chip regulator includes a simple, High/Low-Voltage from 1ms to 131 seconds, can be achieved. Detect (HLVD) circuit. When VDD drops below full-speed The WDT, prescaler and postscaler are reset: operating voltage, the circuit sets the High/Low-Voltage • On any device Reset Detect Interrupt Flag, HLVDIF (IFS4<8>). This can be • On the completion of a clock switch, whether used to generate an interrupt and put the application into invoked by software (i.e., setting the OSWEN bit a low-power operational mode or trigger an orderly after changing the NOSCx bits) or by hardware shutdown. Maximum device speeds as a function of VDD (i.e., Fail-Safe Clock Monitor) are shown in Section29.1 “DC Characteristics”, in Figure29-1 and Figure29-1. • When a PWRSAV instruction is executed (i.e., Sleep or Idle mode is entered) 26.2.2 ON-CHIP REGULATOR AND POR • When the device exits Sleep or Idle mode to resume normal operation For PIC24FV32KA304 devices, it takes a brief time, designated as TPM, for the Voltage Regulator to gener- • By a CLRWDT instruction during normal execution ate a stable output. During this time, code execution is disabled. TPM (DC Specification SY71) is applied every time the device resumes operation after any power-down, including Sleep mode. DS30009995E-page 248  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY If the WDT is enabled in hardware (FWDTEN<1:0> = 11), 26.3.2 CONTROL REGISTER it will continue to run during Sleep or Idle modes. When The WDT is enabled or disabled by the FWDTEN<1:0> the WDT time-out occurs, the device will wake and code Configuration bits. When both the FWDTEN<1:0> execution will continue from where the PWRSAV Configuration bits are set, the WDT is always enabled. instruction was executed. The corresponding SLEEP or IDLE bit (RCON<3:2>) will need to be cleared in software The WDT can be optionally controlled in software when after the device wakes up. the FWDTEN<1:0> Configuration bits have been pro- grammed to ‘10’. The WDT is enabled in software by The WDT Flag bit, WDTO (RCON<4>), is not auto- setting the SWDTEN control bit (RCON<5>). The matically cleared following a WDT time-out. To detect SWDTEN control bit is cleared on any device Reset. subsequent WDT events, the flag must be cleared in The software WDT option allows the user to enable the software. WDT for critical code segments, and disable the WDT Note: The CLRWDT and PWRSAV instructions during non-critical segments, for maximum power clear the prescaler and postscaler counts savings. When the FWTEN<1:0> bits are set to ‘01’, when executed. the WDT is only enabled in Run and Idle modes, and is disabled in Sleep. Software control of the SWDTEN bit 26.3.1 WINDOWED OPERATION (RCON<5>) is disabled with this setting. The Watchdog Timer has an optional Fixed Window mode of operation. In this Windowed mode, CLRWDT instructions can only reset the WDT during the last 1/4 of the programmed WDT period. A CLRWDT instruction executed before that window causes a WDT Reset, similar to a WDT time-out. Windowed WDT mode is enabled by programming the Configuration bit, WINDIS (FWDT<6>), to ‘0’. FIGURE 26-2: WDT BLOCK DIAGRAM SWDTEN LPRC Control FWDTEN<1:0> Wake from Sleep FWPSA WDTPS<3:0> Prescaler WDT Postscaler WDT Overflow LPRC Input (5-Bit/7-Bit) Counter 1:1 to 1:32.768 Reset 31 kHz 1 ms/4 ms All Device Resets Transition to New Clock Source Exit Sleep or Idle Mode CLRWDT Instr. PWRSAV Instr. Sleep or Idle Mode  2011-2017 Microchip Technology Inc. DS30009995E-page 249

PIC24FV32KA304 FAMILY 26.4 Deep Sleep Watchdog Timer 26.6 In-Circuit Serial Programming (DSWDT) PIC24FV32KA304 family microcontrollers can be In PIC24FV32KA304 family devices, in addition to the serially programmed while in the end application circuit. WDT module, a DSWDT module is present which runs This is simply done with two lines for clock (PGECx) and while the device is in Deep Sleep, if enabled. It is driven data (PGEDx), and three other lines for power, ground by either the SOSC or LPRC oscillator. The clock source and the programming voltage. This allows customers to is selected by the Configuration bit, DSWDTOSC manufacture boards with unprogrammed devices and (FDS<4>). then program the microcontroller just before shipping the product. This also allows the most recent firmware or a The DSWDT can be configured to generate a time-out, custom firmware to be programmed. at 2.1 ms to 25.7 days, by selecting the respective postscaler. The postscaler can be selected by the 26.7 In-Circuit Debugger Configuration bits, DSWDTPS<3:0> (FDS<3:0>). When the DSWDT is enabled, the clock source is also When MPLAB® ICD 3, MPLAB REAL ICE™ or PICkit™ enabled. 3 is selected as a debugger, the in-circuit debugging DSWDT is one of the sources that can wake-up the functionality is enabled. This function allows simple device from Deep Sleep mode. debugging functions when used with MPLABIDE. Debugging functionality is controlled through the PGECx 26.5 Program Verification and and PGEDx pins. Code Protection To use the in-circuit debugger function of the device, the design must implement ICSP connections to For all devices in the PIC24FV32KA304 family, code MCLR, VDD, VSS, PGECx, PGEDx and the pin pair. In protection for the Boot Segment (BS) is controlled by the addition, when the feature is enabled, some of the Configuration bit, BSS0, and the General Segment (GS) resources are not available for general use. These by the Configuration bit, GSS0. These bits inhibit exter- resources include the first 80 bytes of data RAM and nal reads and writes to the program memory space two I/O pins. This has no direct effect in normal execution mode. Write protection is controlled by bit, BWRP, for the Boot Segment and bit, GWRP, for the General Segment in the Configuration Word. When these bits are programmed to ‘0’, internal write and erase operations to program memory are blocked. DS30009995E-page 250  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 27.0 DEVELOPMENT SUPPORT 27.1 MPLAB X Integrated Development Environment Software The PIC® microcontrollers (MCU) and dsPIC® digital signal controllers (DSC) are supported with a full range The MPLAB X IDE is a single, unified graphical user of software and hardware development tools: interface for Microchip and third-party software, and • Integrated Development Environment hardware development tool that runs on Windows®, Linux and Mac OS® X. Based on the NetBeans IDE, - MPLAB® X IDE Software MPLAB X IDE is an entirely new IDE with a host of free • Compilers/Assemblers/Linkers software components and plug-ins for high- - MPLAB XC Compiler performance application development and debugging. - MPASMTM Assembler Moving between tools and upgrading from software - MPLINKTM Object Linker/ simulators to hardware debugging and programming MPLIBTM Object Librarian tools is simple with the seamless user interface. - MPLAB Assembler/Linker/Librarian for With complete project management, visual call graphs, Various Device Families a configurable watch window and a feature-rich editor • Simulators that includes code completion and context menus, MPLAB X IDE is flexible and friendly enough for new - MPLAB X SIM Software Simulator users. With the ability to support multiple tools on • Emulators multiple projects with simultaneous debugging, MPLAB - MPLAB REAL ICE™ In-Circuit Emulator X IDE is also suitable for the needs of experienced • In-Circuit Debuggers/Programmers users. - MPLAB ICD 3 Feature-Rich Editor: - PICkit™ 3 • Color syntax highlighting • Device Programmers • Smart code completion makes suggestions and - MPLAB PM3 Device Programmer provides hints as you type • Low-Cost Demonstration/Development Boards, • Automatic code formatting based on user-defined Evaluation Kits and Starter Kits rules • Third-party development tools • Live parsing User-Friendly, Customizable Interface: • Fully customizable interface: toolbars, toolbar buttons, windows, window placement, etc. • Call graph window Project-Based Workspaces: • Multiple projects • Multiple tools • Multiple configurations • Simultaneous debugging sessions File History and Bug Tracking: • Local file history feature • Built-in support for Bugzilla issue tracker  2011-2017 Microchip Technology Inc. DS30009995E-page 251

PIC24FV32KA304 FAMILY 27.2 MPLAB XC Compilers 27.4 MPLINK Object Linker/ MPLIB Object Librarian The MPLAB XC Compilers are complete ANSI C compilers for all of Microchip’s 8, 16 and 32-bit MCU The MPLINK Object Linker combines relocatable and DSC devices. These compilers provide powerful objects created by the MPASM Assembler. It can link integration capabilities, superior code optimization and relocatable objects from precompiled libraries, using ease of use. MPLAB XC Compilers run on Windows, directives from a linker script. Linux or MAC OS X. The MPLIB Object Librarian manages the creation and For easy source level debugging, the compilers provide modification of library files of precompiled code. When debug information that is optimized to the MPLAB X a routine from a library is called from a source file, only IDE. the modules that contain that routine will be linked in The free MPLAB XC Compiler editions support all with the application. This allows large libraries to be devices and commands, with no time or memory used efficiently in many different applications. restrictions, and offer sufficient code optimization for The object linker/library features include: most applications. • Efficient linking of single libraries instead of many MPLAB XC Compilers include an assembler, linker and smaller files utilities. The assembler generates relocatable object • Enhanced code maintainability by grouping files that can then be archived or linked with other related modules together relocatable object files and archives to create an exe- • Flexible creation of libraries with easy module cutable file. MPLAB XC Compiler uses the assembler listing, replacement, deletion and extraction to produce its object file. Notable features of the assembler include: 27.5 MPLAB Assembler, Linker and • Support for the entire device instruction set Librarian for Various Device • Support for fixed-point and floating-point data Families • Command-line interface • Rich directive set MPLAB Assembler produces relocatable machine code from symbolic assembly language for PIC24, • Flexible macro language PIC32 and dsPIC DSC devices. MPLAB XC Compiler • MPLAB X IDE compatibility uses the assembler to produce its object file. The assembler generates relocatable object files that can 27.3 MPASM Assembler then be archived or linked with other relocatable object files and archives to create an executable file. Notable The MPASM Assembler is a full-featured, universal features of the assembler include: macro assembler for PIC10/12/16/18 MCUs. • Support for the entire device instruction set The MPASM Assembler generates relocatable object files for the MPLINK Object Linker, Intel® standard HEX • Support for fixed-point and floating-point data files, MAP files to detail memory usage and symbol • Command-line interface reference, absolute LST files that contain source lines • Rich directive set and generated machine code, and COFF files for • Flexible macro language debugging. • MPLAB X IDE compatibility The MPASM Assembler features include: • Integration into MPLAB X IDE projects • User-defined macros to streamline assembly code • Conditional assembly for multipurpose source files • Directives that allow complete control over the assembly process DS30009995E-page 252  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 27.6 MPLAB X SIM Software Simulator 27.8 MPLAB ICD 3 In-Circuit Debugger System The MPLAB X SIM Software Simulator allows code development in a PC-hosted environment by simulat- The MPLAB ICD 3 In-Circuit Debugger System is ing the PIC MCUs and dsPIC DSCs on an instruction Microchip’s most cost-effective, high-speed hardware level. On any given instruction, the data areas can be debugger/programmer for Microchip Flash DSC and examined or modified and stimuli can be applied from MCU devices. It debugs and programs PIC Flash a comprehensive stimulus controller. Registers can be microcontrollers and dsPIC DSCs with the powerful, logged to files for further run-time analysis. The trace yet easy-to-use graphical user interface of the MPLAB buffer and logic analyzer display extend the power of IDE. the simulator to record and track program execution, The MPLAB ICD 3 In-Circuit Debugger probe is actions on I/O, most peripherals and internal registers. connected to the design engineer’s PC using a high- The MPLAB X SIM Software Simulator fully supports speed USB 2.0 interface and is connected to the target symbolic debugging using the MPLAB XCCompilers, with a connector compatible with the MPLAB ICD 2 or and the MPASM and MPLAB Assemblers. The soft- MPLAB REAL ICE systems (RJ-11). MPLAB ICD 3 ware simulator offers the flexibility to develop and supports all MPLAB ICD 2 headers. debug code outside of the hardware laboratory envi- ronment, making it an excellent, economical software 27.9 PICkit 3 In-Circuit Debugger/ development tool. Programmer 27.7 MPLAB REAL ICE In-Circuit The MPLAB PICkit 3 allows debugging and program- Emulator System ming of PIC and dsPIC Flash microcontrollers at a most affordable price point using the powerful graphical user The MPLAB REAL ICE In-Circuit Emulator System is interface of the MPLAB IDE. The MPLAB PICkit 3 is Microchip’s next generation high-speed emulator for connected to the design engineer’s PC using a full- Microchip Flash DSC and MCU devices. It debugs and speed USB interface and can be connected to the programs all 8, 16 and 32-bit MCU, and DSC devices target via a Microchip debug (RJ-11) connector (com- with the easy-to-use, powerful graphical user interface of patible with MPLAB ICD 3 and MPLAB REAL ICE). The the MPLAB X IDE. connector uses two device I/O pins and the Reset line The emulator is connected to the design engineer’s to implement in-circuit debugging and In-Circuit Serial PC using a high-speed USB 2.0 interface and is Programming™ (ICSP™). connected to the target with either a connector compatible with in-circuit debugger systems (RJ-11) 27.10 MPLAB PM3 Device Programmer or with the new high-speed, noise tolerant, Low- The MPLAB PM3 Device Programmer is a universal, Voltage Differential Signal (LVDS) interconnection CE compliant device programmer with programmable (CAT5). voltage verification at VDDMIN and VDDMAX for The emulator is field upgradable through future firmware maximum reliability. It features a large LCD display downloads in MPLAB X IDE. MPLAB REAL ICE offers (128 x 64) for menus and error messages, and a mod- significant advantages over competitive emulators ular, detachable socket assembly to support various including full-speed emulation, run-time variable package types. The ICSP cable assembly is included watches, trace analysis, complex breakpoints, logic as a standard item. In Stand-Alone mode, the MPLAB probes, a ruggedized probe interface and long (up to PM3 Device Programmer can read, verify and program three meters) interconnection cables. PIC devices without a PC connection. It can also set code protection in this mode. The MPLAB PM3 connects to the host PC via an RS-232 or USB cable. The MPLAB PM3 has high-speed communications and optimized algorithms for quick programming of large memory devices, and incorporates an MMC card for file storage and data applications.  2011-2017 Microchip Technology Inc. DS30009995E-page 253

PIC24FV32KA304 FAMILY 27.11 Demonstration/Development 27.12 Third-Party Development Tools Boards, Evaluation Kits and Microchip also offers a great collection of tools from Starter Kits third-party vendors. These tools are carefully selected to offer good value and unique functionality. A wide variety of demonstration, development and evaluation boards for various PIC MCUs and dsPIC • Device Programmers and Gang Programmers DSCs allows quick application development on fully from companies, such as SoftLog and CCS functional systems. Most boards include prototyping • Software Tools from companies, such as Gimpel areas for adding custom circuitry and provide applica- and Trace Systems tion firmware and source code for examination and • Protocol Analyzers from companies, such as modification. Saleae and Total Phase The boards support a variety of features, including LEDs, • Demonstration Boards from companies, such as temperature sensors, switches, speakers, RS-232 MikroElektronika, Digilent® and Olimex interfaces, LCD displays, potentiometers and additional • Embedded Ethernet Solutions from companies, EEPROM memory. such as EZ Web Lynx, WIZnet and IPLogika® The demonstration and development boards can be used in teaching environments, for prototyping custom circuits and for learning about various microcontroller applications. In addition to the PICDEM™ and dsPICDEM™ demonstration/development board series of circuits, Microchip has a line of evaluation kits and demonstra- tion software for analog filter design, KEELOQ® security ICs, CAN, IrDA®, PowerSmart battery management, SEEVAL® evaluation system, Sigma-Delta ADC, flow rate sensing, plus many more. Also available are starter kits that contain everything needed to experience the specified device. This usually includes a single application and debug capability, all on one board. Check the Microchip web page (www.microchip.com) for the complete list of demonstration, development and evaluation kits. DS30009995E-page 254  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 28.0 INSTRUCTION SET SUMMARY The literal instructions that involve data movement may use some of the following operands: Note: This chapter is a brief summary of the • A literal value to be loaded into a W register or file PIC24F instruction set architecture and is register (specified by the value of ‘k’) not intended to be a comprehensive • The W register or file register where the literal reference source. value is to be loaded (specified by ‘Wb’ or ‘f’) The PIC24F instruction set adds many enhancements However, literal instructions that involve arithmetic or to the previous PIC® MCU instruction sets, while logical operations use some of the following operands: maintaining an easy migration from previous PIC MCU • The first source operand, which is a register ‘Wb’ instruction sets. Most instructions are a single program without any address modifier memory word. Only three instructions require two program memory locations. • The second source operand, which is a literal value Each single-word instruction is a 24-bit word divided • The destination of the result (only if not the same into an 8-bit opcode, which specifies the instruction as the first source operand), which is typically a type and one or more operands, which further specify register ‘Wd’ with or without an address modifier the operation of the instruction. The instruction set is highly orthogonal and is grouped into four basic The control instructions may use some of the following categories: operands: • Word or byte-oriented operations • A program memory address • Bit-oriented operations • The mode of the Table Read and Table Write • Literal operations instructions • Control operations All instructions are a single word, except for certain double-word instructions, which were made Table28-1 lists the general symbols used in describing double-word instructions so that all of the required the instructions. The PIC24F instruction set summary information is available in these 48 bits. In the second in Table28-2 lists all the instructions, along with the word, the 8MSbs are ‘0’s. If this second word is status flags affected by each instruction. executed as an instruction (by itself), it will execute as Most word or byte-oriented W register instructions a NOP. (including barrel shift instructions) have three Most single-word instructions are executed in a single operands: instruction cycle, unless a conditional test is true or the • The first source operand, which is typically a Program Counter (PC) is changed as a result of the register ‘Wb’ without any address modifier instruction. In these cases, the execution takes two • The second source operand, which is typically a instruction cycles, with the additional instruction register ‘Ws’ with or without an address modifier cycle(s) executed as a NOP. Notable exceptions are • The destination of the result, which is typically a the BRA (unconditional/computed branch), indirect register ‘Wd’ with or without an address modifier CALL/GOTO, all Table Reads and Writes, and RETURN/RETFIE instructions, which are single-word However, word or byte-oriented file register instructions instructions but take two or three cycles. have two operands: Certain instructions that involve skipping over the • The file register specified by the value, ‘f’ subsequent instruction require either two or three • The destination, which could either be the file cycles if the skip is performed, depending on whether register, ‘f’, or the W0 register, which is denoted the instruction being skipped is a single-word or as ‘WREG’ two-word instruction. Moreover, double-word moves Most bit-oriented instructions (including simple require two cycles. The double-word instructions rotate/shift instructions) have two operands: execute in two instruction cycles. • The W register (with or without an address modifier) or file register (specified by the value of ‘Ws’ or ‘f’) • The bit in the W register or file register (specified by a literal value or indirectly by the contents of register ‘Wb’)  2011-2017 Microchip Technology Inc. DS30009995E-page 255

PIC24FV32KA304 FAMILY TABLE 28-1: SYMBOLS USED IN OPCODE DESCRIPTIONS Field Description #text Means literal defined by “text” (text) Means “content of text” [text] Means “the location addressed by text” { } Optional field or operation <n:m> Register bit field .b Byte mode selection .d Double-Word mode selection .S Shadow register select .w Word mode selection (default) bit4 4-bit bit selection field (used in word addressed instructions) {0...15} C, DC, N, OV, Z MCU Status bits: Carry, Digit Carry, Negative, Overflow, Sticky Zero Expr Absolute address, label or expression (resolved by the linker) f File register address {0000h...1FFFh} lit1 1-bit unsigned literal {0,1} lit4 4-bit unsigned literal {0...15} lit5 5-bit unsigned literal {0...31} lit8 8-bit unsigned literal {0...255} lit10 10-bit unsigned literal {0...255} for Byte mode, {0:1023} for Word mode lit14 14-bit unsigned literal {0...16384} lit16 16-bit unsigned literal {0...65535} lit23 23-bit unsigned literal {0...8388608}; LSB must be ‘0’ None Field does not require an entry, may be blank PC Program Counter Slit10 10-bit signed literal {-512...511} Slit16 16-bit signed literal {-32768...32767} Slit6 6-bit signed literal {-16...16} Wb Base W register {W0..W15} Wd Destination W register { Wd, [Wd], [Wd++], [Wd--], [++Wd], [--Wd] } Wdo Destination W register  { Wnd, [Wnd], [Wnd++], [Wnd--], [++Wnd], [--Wnd], [Wnd+Wb] } Wm,Wn Dividend, Divisor Working register pair (direct addressing) Wn One of 16 Working registers {W0..W15} Wnd One of 16 destination Working registers {W0..W15} Wns One of 16 source Working registers {W0..W15} WREG W0 (Working register used in File register instructions) Ws Source W register { Ws, [Ws], [Ws++], [Ws--], [++Ws], [--Ws] } Wso Source W register { Wns, [Wns], [Wns++], [Wns--], [++Wns], [--Wns], [Wns+Wb] } DS30009995E-page 256  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY TABLE 28-2: INSTRUCTION SET OVERVIEW Assembly # of # of Status Flags Assembly Syntax Description Mnemonic Words Cycles Affected ADD ADD f f = f + WREG 1 1 C, DC, N, OV, Z ADD f,WREG WREG = f + WREG 1 1 C, DC, N, OV, Z ADD #lit10,Wn Wd = lit10 + Wd 1 1 C, DC, N, OV, Z ADD Wb,Ws,Wd Wd = Wb + Ws 1 1 C, DC, N, OV, Z ADD Wb,#lit5,Wd Wd = Wb + lit5 1 1 C, DC, N, OV, Z ADDC ADDC f f = f + WREG + (C) 1 1 C, DC, N, OV, Z ADDC f,WREG WREG = f + WREG + (C) 1 1 C, DC, N, OV, Z ADDC #lit10,Wn Wd = lit10 + Wd + (C) 1 1 C, DC, N, OV, Z ADDC Wb,Ws,Wd Wd = Wb + Ws + (C) 1 1 C, DC, N, OV, Z ADDC Wb,#lit5,Wd Wd = Wb + lit5 + (C) 1 1 C, DC, N, OV, Z AND AND f f = f .AND. WREG 1 1 N, Z AND f,WREG WREG = f .AND. WREG 1 1 N, Z AND #lit10,Wn Wd = lit10 .AND. Wd 1 1 N, Z AND Wb,Ws,Wd Wd = Wb .AND. Ws 1 1 N, Z AND Wb,#lit5,Wd Wd = Wb .AND. lit5 1 1 N, Z ASR ASR f f = Arithmetic Right Shift f 1 1 C, N, OV, Z ASR f,WREG WREG = Arithmetic Right Shift f 1 1 C, N, OV, Z ASR Ws,Wd Wd = Arithmetic Right Shift Ws 1 1 C, N, OV, Z ASR Wb,Wns,Wnd Wnd = Arithmetic Right Shift Wb by Wns 1 1 N, Z ASR Wb,#lit5,Wnd Wnd = Arithmetic Right Shift Wb by lit5 1 1 N, Z BCLR BCLR f,#bit4 Bit Clear f 1 1 None BCLR Ws,#bit4 Bit Clear Ws 1 1 None BRA BRA C,Expr Branch if Carry 1 1 (2) None BRA GE,Expr Branch if Greater than or Equal 1 1 (2) None BRA GEU,Expr Branch if Unsigned Greater than or Equal 1 1 (2) None BRA GT,Expr Branch if Greater than 1 1 (2) None BRA GTU,Expr Branch if Unsigned Greater than 1 1 (2) None BRA LE,Expr Branch if Less than or Equal 1 1 (2) None BRA LEU,Expr Branch if Unsigned Less than or Equal 1 1 (2) None BRA LT,Expr Branch if Less than 1 1 (2) None BRA LTU,Expr Branch if Unsigned Less than 1 1 (2) None BRA N,Expr Branch if Negative 1 1 (2) None BRA NC,Expr Branch if Not Carry 1 1 (2) None BRA NN,Expr Branch if Not Negative 1 1 (2) None BRA NOV,Expr Branch if Not Overflow 1 1 (2) None BRA NZ,Expr Branch if Not Zero 1 1 (2) None BRA OV,Expr Branch if Overflow 1 1 (2) None BRA Expr Branch Unconditionally 1 2 None BRA Z,Expr Branch if Zero 1 1 (2) None BRA Wn Computed Branch 1 2 None BSET BSET f,#bit4 Bit Set f 1 1 None BSET Ws,#bit4 Bit Set Ws 1 1 None BSW BSW.C Ws,Wb Write C bit to Ws<Wb> 1 1 None BSW.Z Ws,Wb Write Z bit to Ws<Wb> 1 1 None BTG BTG f,#bit4 Bit Toggle f 1 1 None BTG Ws,#bit4 Bit Toggle Ws 1 1 None BTSC BTSC f,#bit4 Bit Test f, Skip if Clear 1 1 None (2 or 3) BTSC Ws,#bit4 Bit Test Ws, Skip if Clear 1 1 None (2 or 3)  2011-2017 Microchip Technology Inc. DS30009995E-page 257

PIC24FV32KA304 FAMILY TABLE 28-2: INSTRUCTION SET OVERVIEW (CONTINUED) Assembly # of # of Status Flags Assembly Syntax Description Mnemonic Words Cycles Affected BTSS BTSS f,#bit4 Bit Test f, Skip if Set 1 1 None (2 or 3) BTSS Ws,#bit4 Bit Test Ws, Skip if Set 1 1 None (2 or 3) BTST BTST f,#bit4 Bit Test f 1 1 Z BTST.C Ws,#bit4 Bit Test Ws to C 1 1 C BTST.Z Ws,#bit4 Bit Test Ws to Z 1 1 Z BTST.C Ws,Wb Bit Test Ws<Wb> to C 1 1 C BTST.Z Ws,Wb Bit Test Ws<Wb> to Z 1 1 Z BTSTS BTSTS f,#bit4 Bit Test then Set f 1 1 Z BTSTS.C Ws,#bit4 Bit Test Ws to C, then Set 1 1 C BTSTS.Z Ws,#bit4 Bit Test Ws to Z, then Set 1 1 Z CALL CALL lit23 Call Subroutine 2 2 None CALL Wn Call Indirect Subroutine 1 2 None CLR CLR f f = 0x0000 1 1 None CLR WREG WREG = 0x0000 1 1 None CLR Ws Ws = 0x0000 1 1 None CLRWDT CLRWDT Clear Watchdog Timer 1 1 WDTO, Sleep COM COM f f = f 1 1 N, Z COM f,WREG WREG = f 1 1 N, Z COM Ws,Wd Wd = Ws 1 1 N, Z CP CP f Compare f with WREG 1 1 C, DC, N, OV, Z CP Wb,#lit5 Compare Wb with lit5 1 1 C, DC, N, OV, Z CP Wb,Ws Compare Wb with Ws (Wb – Ws) 1 1 C, DC, N, OV, Z CP0 CP0 f Compare f with 0x0000 1 1 C, DC, N, OV, Z CP0 Ws Compare Ws with 0x0000 1 1 C, DC, N, OV, Z CPB CPB f Compare f with WREG, with Borrow 1 1 C, DC, N, OV, Z CPB Wb,#lit5 Compare Wb with lit5, with Borrow 1 1 C, DC, N, OV, Z CPB Wb,Ws Compare Wb with Ws, with Borrow 1 1 C, DC, N, OV, Z (Wb – Ws – C) CPSEQ CPSEQ Wb,Wn Compare Wb with Wn, Skip if = 1 1 None (2 or 3) CPSGT CPSGT Wb,Wn Compare Wb with Wn, Skip if > 1 1 None (2 or 3) CPSLT CPSLT Wb,Wn Compare Wb with Wn, Skip if < 1 1 None (2 or 3) CPSNE CPSNE Wb,Wn Compare Wb with Wn, Skip if  1 1 None (2 or 3) DAW DAW Wn Wn = Decimal Adjust Wn 1 1 C DEC DEC f f = f –1 1 1 C, DC, N, OV, Z DEC f,WREG WREG = f –1 1 1 C, DC, N, OV, Z DEC Ws,Wd Wd = Ws – 1 1 1 C, DC, N, OV, Z DEC2 DEC2 f f = f – 2 1 1 C, DC, N, OV, Z DEC2 f,WREG WREG = f – 2 1 1 C, DC, N, OV, Z DEC2 Ws,Wd Wd = Ws – 2 1 1 C, DC, N, OV, Z DISI DISI #lit14 Disable Interrupts for k Instruction Cycles 1 1 None DIV DIV.SW Wm,Wn Signed 16/16-bit Integer Divide 1 18 N, Z, C, OV DIV.SD Wm,Wn Signed 32/16-bit Integer Divide 1 18 N, Z, C, OV DIV.UW Wm,Wn Unsigned 16/16-bit Integer Divide 1 18 N, Z, C, OV DIV.UD Wm,Wn Unsigned 32/16-bit Integer Divide 1 18 N, Z, C, OV EXCH EXCH Wns,Wnd Swap Wns with Wnd 1 1 None FF1L FF1L Ws,Wnd Find First One from Left (MSb) Side 1 1 C FF1R FF1R Ws,Wnd Find First One from Right (LSb) Side 1 1 C DS30009995E-page 258  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY TABLE 28-2: INSTRUCTION SET OVERVIEW (CONTINUED) Assembly # of # of Status Flags Assembly Syntax Description Mnemonic Words Cycles Affected GOTO GOTO Expr Go to Address 2 2 None GOTO Wn Go to Indirect 1 2 None INC INC f f = f + 1 1 1 C, DC, N, OV, Z INC f,WREG WREG = f + 1 1 1 C, DC, N, OV, Z INC Ws,Wd Wd = Ws + 1 1 1 C, DC, N, OV, Z INC2 INC2 f f = f + 2 1 1 C, DC, N, OV, Z INC2 f,WREG WREG = f + 2 1 1 C, DC, N, OV, Z INC2 Ws,Wd Wd = Ws + 2 1 1 C, DC, N, OV, Z IOR IOR f f = f .IOR. WREG 1 1 N, Z IOR f,WREG WREG = f .IOR. WREG 1 1 N, Z IOR #lit10,Wn Wd = lit10 .IOR. Wd 1 1 N, Z IOR Wb,Ws,Wd Wd = Wb .IOR. Ws 1 1 N, Z IOR Wb,#lit5,Wd Wd = Wb .IOR. lit5 1 1 N, Z LNK LNK #lit14 Link Frame Pointer 1 1 None LSR LSR f f = Logical Right Shift f 1 1 C, N, OV, Z LSR f,WREG WREG = Logical Right Shift f 1 1 C, N, OV, Z LSR Ws,Wd Wd = Logical Right Shift Ws 1 1 C, N, OV, Z LSR Wb,Wns,Wnd Wnd = Logical Right Shift Wb by Wns 1 1 N, Z LSR Wb,#lit5,Wnd Wnd = Logical Right Shift Wb by lit5 1 1 N, Z MOV MOV f,Wn Move f to Wn 1 1 None MOV [Wns+Slit10],Wnd Move [Wns+Slit10] to Wnd 1 1 None MOV f Move f to f 1 1 N, Z MOV f,WREG Move f to WREG 1 1 N, Z MOV #lit16,Wn Move 16-bit Literal to Wn 1 1 None MOV.b #lit8,Wn Move 8-bit Literal to Wn 1 1 None MOV Wn,f Move Wn to f 1 1 None MOV Wns,[Wns+Slit10] Move Wns to [Wns+Slit10] 1 1 None MOV Wso,Wdo Move Ws to Wd 1 1 None MOV WREG,f Move WREG to f 1 1 N, Z MOV.D Wns,Wd Move Double from W(ns):W(ns+1) to Wd 1 2 None MOV.D Ws,Wnd Move Double from Ws to W(nd+1):W(nd) 1 2 None MUL MUL.SS Wb,Ws,Wnd {Wnd+1, Wnd} = Signed(Wb) * Signed(Ws) 1 1 None MUL.SU Wb,Ws,Wnd {Wnd+1, Wnd} = Signed(Wb) * Unsigned(Ws) 1 1 None MUL.US Wb,Ws,Wnd {Wnd+1, Wnd} = Unsigned(Wb) * Signed(Ws) 1 1 None MUL.UU Wb,Ws,Wnd {Wnd+1, Wnd} = Unsigned(Wb) * Unsigned(Ws) 1 1 None MUL.SU Wb,#lit5,Wnd {Wnd+1, Wnd} = Signed(Wb) * Unsigned(lit5) 1 1 None MUL.UU Wb,#lit5,Wnd {Wnd+1, Wnd} = Unsigned(Wb) * Unsigned(lit5) 1 1 None MUL f W3:W2 = f * WREG 1 1 None NEG NEG f f = f + 1 1 1 C, DC, N, OV, Z NEG f,WREG WREG = f + 1 1 1 C, DC, N, OV, Z NEG Ws,Wd Wd = Ws + 1 1 1 C, DC, N, OV, Z NOP NOP No Operation 1 1 None NOPR No Operation 1 1 None POP POP f Pop f from Top-of-Stack (TOS) 1 1 None POP Wdo Pop from Top-of-Stack (TOS) to Wdo 1 1 None POP.D Wnd Pop from Top-of-Stack (TOS) to W(nd):W(nd+1) 1 2 None POP.S Pop Shadow Registers 1 1 All PUSH PUSH f Push f to Top-of-Stack (TOS) 1 1 None PUSH Wso Push Wso to Top-of-Stack (TOS) 1 1 None PUSH.D Wns Push W(ns):W(ns+1) to Top-of-Stack (TOS) 1 2 None PUSH.S Push Shadow Registers 1 1 None  2011-2017 Microchip Technology Inc. DS30009995E-page 259

PIC24FV32KA304 FAMILY TABLE 28-2: INSTRUCTION SET OVERVIEW (CONTINUED) Assembly # of # of Status Flags Assembly Syntax Description Mnemonic Words Cycles Affected PWRSAV PWRSAV #lit1 Go into Sleep or Idle mode 1 1 WDTO, Sleep RCALL RCALL Expr Relative Call 1 2 None RCALL Wn Computed Call 1 2 None REPEAT REPEAT #lit14 Repeat Next Instruction lit14 + 1 times 1 1 None REPEAT Wn Repeat Next Instruction (Wn) + 1 times 1 1 None RESET RESET Software Device Reset 1 1 None RETFIE RETFIE Return from Interrupt 1 3 (2) None RETLW RETLW #lit10,Wn Return with Literal in Wn 1 3 (2) None RETURN RETURN Return from Subroutine 1 3 (2) None RLC RLC f f = Rotate Left through Carry f 1 1 C, N, Z RLC f,WREG WREG = Rotate Left through Carry f 1 1 C, N, Z RLC Ws,Wd Wd = Rotate Left through Carry Ws 1 1 C, N, Z RLNC RLNC f f = Rotate Left (No Carry) f 1 1 N, Z RLNC f,WREG WREG = Rotate Left (No Carry) f 1 1 N, Z RLNC Ws,Wd Wd = Rotate Left (No Carry) Ws 1 1 N, Z RRC RRC f f = Rotate Right through Carry f 1 1 C, N, Z RRC f,WREG WREG = Rotate Right through Carry f 1 1 C, N, Z RRC Ws,Wd Wd = Rotate Right through Carry Ws 1 1 C, N, Z RRNC RRNC f f = Rotate Right (No Carry) f 1 1 N, Z RRNC f,WREG WREG = Rotate Right (No Carry) f 1 1 N, Z RRNC Ws,Wd Wd = Rotate Right (No Carry) Ws 1 1 N, Z SE SE Ws,Wnd Wnd = Sign-Extended Ws 1 1 C, N, Z SETM SETM f f = FFFFh 1 1 None SETM WREG WREG = FFFFh 1 1 None SETM Ws Ws = FFFFh 1 1 None SL SL f f = Left Shift f 1 1 C, N, OV, Z SL f,WREG WREG = Left Shift f 1 1 C, N, OV, Z SL Ws,Wd Wd = Left Shift Ws 1 1 C, N, OV, Z SL Wb,Wns,Wnd Wnd = Left Shift Wb by Wns 1 1 N, Z SL Wb,#lit5,Wnd Wnd = Left Shift Wb by lit5 1 1 N, Z SUB SUB f f = f – WREG 1 1 C, DC, N, OV, Z SUB f,WREG WREG = f – WREG 1 1 C, DC, N, OV, Z SUB #lit10,Wn Wn = Wn – lit10 1 1 C, DC, N, OV, Z SUB Wb,Ws,Wd Wd = Wb – Ws 1 1 C, DC, N, OV, Z SUB Wb,#lit5,Wd Wd = Wb – lit5 1 1 C, DC, N, OV, Z SUBB SUBB f f = f – WREG – (C) 1 1 C, DC, N, OV, Z SUBB f,WREG WREG = f – WREG – (C) 1 1 C, DC, N, OV, Z SUBB #lit10,Wn Wn = Wn – lit10 – (C) 1 1 C, DC, N, OV, Z SUBB Wb,Ws,Wd Wd = Wb – Ws – (C) 1 1 C, DC, N, OV, Z SUBB Wb,#lit5,Wd Wd = Wb – lit5 – (C) 1 1 C, DC, N, OV, Z SUBR SUBR f f = WREG – f 1 1 C, DC, N, OV, Z SUBR f,WREG WREG = WREG – f 1 1 C, DC, N, OV, Z SUBR Wb,Ws,Wd Wd = Ws – Wb 1 1 C, DC, N, OV, Z SUBR Wb,#lit5,Wd Wd = lit5 – Wb 1 1 C, DC, N, OV, Z SUBBR SUBBR f f = WREG – f – (C) 1 1 C, DC, N, OV, Z SUBBR f,WREG WREG = WREG – f – (C) 1 1 C, DC, N, OV, Z SUBBR Wb,Ws,Wd Wd = Ws – Wb – (C) 1 1 C, DC, N, OV, Z SUBBR Wb,#lit5,Wd Wd = lit5 – Wb – (C) 1 1 C, DC, N, OV, Z SWAP SWAP.b Wn Wn = Nibble Swap Wn 1 1 None SWAP Wn Wn = Byte Swap Wn 1 1 None TBLRDH TBLRDH Ws,Wd Read Prog<23:16> to Wd<7:0> 1 2 None DS30009995E-page 260  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY TABLE 28-2: INSTRUCTION SET OVERVIEW (CONTINUED) Assembly # of # of Status Flags Assembly Syntax Description Mnemonic Words Cycles Affected TBLRDL TBLRDL Ws,Wd Read Prog<15:0> to Wd 1 2 None TBLWTH TBLWTH Ws,Wd Write Ws<7:0> to Prog<23:16> 1 2 None TBLWTL TBLWTL Ws,Wd Write Ws to Prog<15:0> 1 2 None ULNK ULNK Unlink Frame Pointer 1 1 None XOR XOR f f = f .XOR. WREG 1 1 N, Z XOR f,WREG WREG = f .XOR. WREG 1 1 N, Z XOR #lit10,Wn Wd = lit10 .XOR. Wd 1 1 N, Z XOR Wb,Ws,Wd Wd = Wb .XOR. Ws 1 1 N, Z XOR Wb,#lit5,Wd Wd = Wb .XOR. lit5 1 1 N, Z ZE ZE Ws,Wnd Wnd = Zero-Extend Ws 1 1 C, Z, N  2011-2017 Microchip Technology Inc. DS30009995E-page 261

PIC24FV32KA304 FAMILY NOTES: DS30009995E-page 262  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 29.0 ELECTRICAL CHARACTERISTICS This section provides an overview of the PIC24FV32KA304 family electrical characteristics. Additional information will be provided in future revisions of this document as it becomes available. Absolute maximum ratings for the PIC24FV32KA304 family devices are listed below. Exposure to these maximum rating conditions for extended periods may affect device reliability. Functional operation of the device at these, or any other conditions above the parameters indicated in the operation listings of this specification, is not implied. Absolute Maximum Ratings(†) Ambient temperature under bias.............................................................................................................-40°C to +125°C Storage temperature.............................................................................................................................. -65°C to +150°C Voltage on VDD with respect to VSS (PIC24FVXXKA30X) ....................................................................... -0.3V to +6.5V Voltage on VDD with respect to VSS (PIC24FXXKA30X) .......................................................................... -0.3V to +4.5V Voltage on any combined analog and digital pin with respect to VSS ............................................-0.3V to (VDD + 0.3V) Voltage on any digital only pin with respect to VSS ....................................................................... -0.3V to (VDD + 0.3V) Voltage on MCLR/VPP pin with respect to VSS ......................................................................................... -0.3V to +9.0V Maximum current out of VSS pin...........................................................................................................................300 mA Maximum current into VDD pin(1)...........................................................................................................................250 mA Maximum output current sunk by any I/O pin..........................................................................................................25 mA Maximum output current sourced by any I/O pin....................................................................................................25 mA Maximum current sunk by all ports.......................................................................................................................200 mA Maximum current sourced by all ports(1)...............................................................................................................200 mA Note 1: Maximum allowable current is a function of the device maximum power dissipation (see Table29-1). † NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability.  2011-2017 Microchip Technology Inc. DS30009995E-page 263

PIC24FV32KA304 FAMILY 29.1 DC Characteristics FIGURE 29-1: PIC24FV32KA304 VOLTAGE-FREQUENCY GRAPH (INDUSTRIAL AND EXTENDED) 5.5V 5.5V 3.20V 3.20V )D D V ( e g 2.00V a t ol V 8 MHz 32 MHz Frequency Note: For frequencies between 8MHz and 32MHz, FMAX = 20 MHz * (VDD – 2.0) + 8 MHz. FIGURE 29-2: PIC24F32KA304 FAMILY VOLTAGE-FREQUENCY GRAPH (INDUSTRIAL AND EXTENDED) 3.60V 3.60V 3.00V 3.00V )D D V ( e g 1.80V a t ol V 8 MHz 32 MHz Frequency Note: For frequencies between 8MHz and 32MHz, FMAX = 20 MHz * (VDD – 1.8) + 8 MHz. DS30009995E-page 264  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY TABLE 29-1: THERMAL OPERATING CONDITIONS Rating Symbol Min Typ Max Unit Operating Junction Temperature Range TJ -40 — +140 °C Operating Ambient Temperature Range TA -40 — +125 °C Power Dissipation: Internal Chip Power Dissipation: PINT = VDD x (IDD –  IOH) PD PINT + PI/O W I/O Pin Power Dissipation: PI/O =  ({VDD – VOH} x IOH) +  (VOL x IOL) Maximum Allowed Power Dissipation PDMAX (TJ – TA)/JA W TABLE 29-2: THERMAL PACKAGING CHARACTERISTICS Characteristic Symbol Typ Max Unit Notes Package Thermal Resistance, 20-Pin SPDIP JA 62.4 — °C/W 1 Package Thermal Resistance, 28-Pin SPDIP JA 60 — °C/W 1 Package Thermal Resistance, 20-Pin SSOP JA 108 — °C/W 1 Package Thermal Resistance, 28-Pin SSOP JA 71 — °C/W 1 Package Thermal Resistance, 20-Pin SOIC JA 75 — °C/W 1 Package Thermal Resistance, 28-Pin SOIC JA 80.2 — °C/W 1 Package Thermal Resistance, 28-Pin QFN JA 32 — °C/W 1 Package Thermal Resistance, 44-Pin QFN JA 29 — °C/W 1 Package Thermal Resistance, 48-Pin UQFN JA — — °C/W 1 Note 1: Junction to ambient thermal resistance, Theta-JA (JA) numbers are achieved by package simulations. TABLE 29-3: DC CHARACTERISTICS: TEMPERATURE AND VOLTAGE SPECIFICATIONS Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX DC CHARACTERISTICS Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Param Symbol Characteristic Min Typ(1) Max Units Conditions No. DC10 VDD Supply Voltage 1.8 — 3.6 V For F devices 2.0 — 5.5 V For FV devices DC12 VDR RAM Data Retention 1.5 — — V For F devices Voltage(2) 1.7 — — V For FV devices DC16 VPOR VDD Start Voltage VSS — 50 mV VDD must be maintained in this range to Ensure Internal for at least 64ms. Power-on Reset Signal DC17 SVDD VDD Rise Rate 0.05 — — V/ms 0-3.3V in 0.1s to Ensure Internal 0-2.5V in 60ms Power-on Reset Signal Note 1: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated. Parameters are for design guidance only and are not tested. 2: This is the limit to which VDD can be lowered without losing RAM data.  2011-2017 Microchip Technology Inc. DS30009995E-page 265

PIC24FV32KA304 FAMILY TABLE 29-4: HIGH/LOW–VOLTAGE DETECT CHARACTERISTICS Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Param Symbol Characteristic Min Typ Max Units Conditions No. DC18 VHLVD HLVD Voltage on HLVDL<3:0> = 0000(2) — — 1.90 V VDD Transition HLVDL<3:0> = 0001 1.86 — 2.13 V HLVDL<3:0> = 0010 2.08 — 2.35 V HLVDL<3:0> = 0011 2.22 — 2.53 V HLVDL<3:0> = 0100 2.30 — 2.62 V HLVDL<3:0> = 0101 2.49 — 2.84 V HLVDL<3:0> = 0110 2.73 — 3.10 V HLVDL<3:0> = 0111 2.86 — 3.25 V HLVDL<3:0> = 1000 3.00 — 3.41 V HLVDL<3:0> = 1001 3.16 — 3.59(1) V HLVDL<3:0> = 1010(1) 3.33 — 3.79 V HLVDL<3:0> = 1011(1) 3.53 — 4.01 V HLVDL<3:0> = 1100(1) 3.74 — 4.26 V HLVDL<3:0> = 1101(1) 4.00 — 4.55 V HLVDL<3:0> = 1110(1) 4.28 — 4.87 V Note 1: These trip points should not be used on PIC24FXXKA30X devices. 2: This trip point should not be used on PIC24FVXXKA30X devices. TABLE 29-5: BOR TRIP POINTS Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Param Sym Characteristic Min Typ Max Units Conditions No. DC15 BOR Hysteresis — 5 — mV DC19 BOR Voltage on VDD BORV<1:0> = 00 — — — — Valid for LPBOR and DSBOR Transition (Note 1) BORV<1:0> = 01 2.90 3 3.38 V BORV<1:0> = 10 2.53 2.7 3.07 V BORV<1:0> = 11 1.75 1.85 2.05 V (Note 2) BORV<1:0> = 11 1.95 2.05 2.16 V (Note 3) Note 1: LPBOR re-arms the POR circuit but does not cause a BOR. 2: This is valid for PIC24F (3.3V) devices. 3: This is valid for PIC24FV (5V) devices. DS30009995E-page 266  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY TABLE 29-6: DC CHARACTERISTICS: OPERATING CURRENT (IDD) Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX DC CHARACTERISTICS Operating temperature: -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Parameter No. Device Typical Max Units Conditions IDD Current D20 PIC24FV32KA3XX 269 450 µA 2.0V 465 830 µA 5.0V 0.5 MIPS, PIC24F32KA3XX 200 330 µA 1.8V FOSC = 1 MHz(1) 410 750 µA 3.3V DC22 PIC24FV32KA3XX 490 — µA 2.0V 880 — µA 5.0V 1 MIPS, PIC24F32KA3XX 407 — µA 1.8V FOSC = 2 MHz(1) 800 — µA 3.3V DC24 PIC24FV32KA3XX 13.0 20.0 mA 5.0V 16 MIPS, PIC24F32KA3XX 12.0 18.0 mA 3.3V FOSC = 32 MHz(1) DC26 PIC24FV32KA3XX 2.0 — mA 2.0V 3.5 — mA 5.0V FRC (4 MIPS), PIC24F32KA3XX 1.80 — mA 1.8V FOSC = 8 MHz 3.40 — mA 3.3V DC30 PIC24FV32KA3XX 48.0 250 µA 2.0V 75.0 450 µA 5.0V LPRC (15.5 KIPS), PIC24F32KA3XX 8.1 28 µA 1.8V FOSC = 31 kHz 13.50 150 µA 3.3V Legend: Unshaded rows represent PIC24F32KA3XX devices and shaded rows represent PIC24FV32KA3XX devices. Note 1: Oscillator is in External Clock mode (FOSCSEL<2:0> = 010, FOSC<1:0> = 00).  2011-2017 Microchip Technology Inc. DS30009995E-page 267

PIC24FV32KA304 FAMILY TABLE 29-7: DC CHARACTERISTICS: IDLE CURRENT (IIDLE) Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX DC CHARACTERISTICS Operating temperature: -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Parameter No. Device Typical Max Units Conditions Idle Current (IIDLE) DC40 PIC24FV32KA3XX 120 200 µA 2.0V 160 430 µA 5.0V 0.5 MIPS, PIC24F32KA3XX 50 100 µA 1.8V FOSC = 1 MHz(1) 90 370 µA 3.3V DC42 PIC24FV32KA3XX 165 — µA 2.0V 260 — µA 5.0V 1 MIPS, PIC24F32KA3XX 95 — µA 1.8V FOSC = 2 MHz(1) 180 — µA 3.3V DC44 PIC24FV32KA3XX 3.1 6.5 mA 5.0V 16 MIPS, PIC24F32KA3XX 2.9 6.0 mA 3.3V FOSC = 32 MHz(1) DC46 PIC24FV32KA3XX 0.65 — mA 2.0V 1.0 — mA 5.0V FRC (4 MIPS), PIC24F32KA3XX 0.55 — mA 1.8V FOSC = 8 MHz 1.0 — mA 3.3V DC50 PIC24FV32KA3XX 60 200 µA 2.0V 70 350 µA 5.0V LPRC (15.5 KIPS), PIC24F32KA3XX 2.2 18 µA 1.8V FOSC = 31 kHz 4.0 60 µA 3.3V Legend: Unshaded rows represent PIC24F32KA3XX devices and shaded rows represent PIC24FV32KA3XX devices. Note 1: Oscillator is in External Clock mode (FOSCSEL<2:0> = 010, FOSC<1:0> = 00). DS30009995E-page 268  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY TABLE 29-8: DC CHARACTERISTICS: POWER-DOWN CURRENT (IPD) Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX DC CHARACTERISTICS Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Parameter Device Typical(1) Max Units Conditions No. Power-Down Current (IPD) DC60 PIC24FV32KA3XX — -40°C 8.0 +25°C 6.0 8.5 µA +60°C 2.0V 9.0 +85°C — 15 +125°C — -40°C 8.0 +25°C 6.0 9.0 µA +60°C 5.0V 10.0 +85°C — 15 +125°C Sleep Mode(2) PIC24F32KA3XX — -40°C 0.80 +25°C 0.025 1.5 µA +60°C 1.8V 2.0 +85°C — 7.5 +125°C — -40°C 1.0 +25°C 0.040 2.0 µA +60°C 3.3V 3.0 +85°C — 7.5 +125°C DC61 PIC24FV32KA3XX 0.25 — µA -40°C 2.0V Low-Voltage 0.35 3.0 µA +85°C 5.0V Sleep Mode(2) — 7.5 µA +125°C 5.0V DC70 PIC24FV32KA3XX 0.03 — µA -40°C 2.0V 0.10 2.0 µA +85°C 5.0V — 6.0 µA +125°C 5.0V Deep Sleep Mode PIC24F32KA3XX 0.02 — µA -40°C 1.8V 0.08 1.2 µA +85°C 3.3V — 1.2 µA +125°C 3.3V Legend: Unshaded rows represent PIC24F32KA3XX devices and shaded rows represent PIC24FV32KA3XX devices. Note 1: Data in the Typical column is at 3.3V, +25°C (PIC24F32KA3XX) or 5.0V, +25°C (PIC24FV32KA3XX) unless otherwise stated. Parameters are for design guidance only and are not tested. 2: Base IPD is measured with all peripherals and clocks shut down. All I/Os are configured as outputs and set low, PMSLP is set to ‘0’ and WDT, etc., are all switched off. 3: The  current is the additional current consumed when the module is enabled. This current should be added to the base IPD current. 4: This current applies to Sleep only. 5: This current applies to Sleep and Deep Sleep. 6: This current applies to Deep Sleep only.  2011-2017 Microchip Technology Inc. DS30009995E-page 269

PIC24FV32KA304 FAMILY TABLE 29-8: DC CHARACTERISTICS: POWER-DOWN CURRENT (IPD) (CONTINUED) Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX DC CHARACTERISTICS Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Parameter Device Typical(1) Max Units Conditions No. Module Differential Current (IPD)(3) DC71 PIC24FV32KA3XX 0.50 — µA -40°C 2.0V 0.70 1.5 µA +85°C 5.0V — 1.5 µA +125°C 5.0V Watchdog Timer Current: PIC24F32KA3XX 0.50 — µA -40°C 1.8V IWDT(4) 0.70 1.5 µA +85°C 3.3V — 1.5 µA +125°C 3.3V DC72 PIC24FV32KA3XX 0.80 — µA -40°C 2.0V 1.50 2.0 µA +85°C 5.0V 32 kHz Crystal with RTCC, — 2.0 µA +125°C 5.0V DSWDT or Timer1: ISOSC PIC24F32KA3XX 0.70 — µA -40°C 1.8V (SOSCSEL = 0)(5) 1.0 1.5 µA +85°C 3.3V — 1.5 µA +125°C 3.3V DC75 PIC24FV32KA3XX 5.4 — µA -40°C 2.0V 8.1 14.0 µA +85°C 5.0V — 14.0 µA +125°C 5.0V IHLVD(4) PIC24F32KA3XX 4.9 — µA -40°C 1.8V 7.5 14.0 µA +85°C 3.3V — 14.0 µA +125°C 3.3V DC76 PIC24FV32KA3XX 5.6 — µA -40°C 2.0V 6.5 11.2 µA -40°C 5.0V — 11.2 µA +125°C 5.0V IBOR(4) PIC24F32KA3XX 5.6 — µA -40°C 1.8V 6.0 11.2 µA +85°C 3.3V — 11.2 µA +125°C 3.3V Legend: Unshaded rows represent PIC24F32KA3XX devices and shaded rows represent PIC24FV32KA3XX devices. Note 1: Data in the Typical column is at 3.3V, +25°C (PIC24F32KA3XX) or 5.0V, +25°C (PIC24FV32KA3XX) unless otherwise stated. Parameters are for design guidance only and are not tested. 2: Base IPD is measured with all peripherals and clocks shut down. All I/Os are configured as outputs and set low, PMSLP is set to ‘0’ and WDT, etc., are all switched off. 3: The  current is the additional current consumed when the module is enabled. This current should be added to the base IPD current. 4: This current applies to Sleep only. 5: This current applies to Sleep and Deep Sleep. 6: This current applies to Deep Sleep only. DS30009995E-page 270  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY TABLE 29-8: DC CHARACTERISTICS: POWER-DOWN CURRENT (IPD) (CONTINUED) Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX DC CHARACTERISTICS Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Parameter Device Typical(1) Max Units Conditions No. Module Differential Current (IPD)(3) DC78 PIC24FV32KA3XX 0.03 — µA -40°C 2.0V 0.05 0.20 µA +85°C 5.0V — 0.30 µA +125°C 5.0V Deep Sleep BOR: PIC24F32KA3XX 0.03 — µA -40°C 1.8V ILPBOR(5) 0.05 0.20 µA +85°C 3.3V — 0.30 µA +125°C 3.3V DC80 PIC24FV32KA3XX 0.20 — µA -40°C 2.0V 0.70 1.5 µA +85°C 5.0V — 1.5 µA +125°C 5.0V Deep Sleep WDT: PIC24F32KA3XX 0.20 — µA -40°C 1.8V IDSWDT (LPRC)(6) 0.35 0.8 µA +85°C 3.3V — 1.5 µA +125°C 3.3V Legend: Unshaded rows represent PIC24F32KA3XX devices and shaded rows represent PIC24FV32KA3XX devices. Note 1: Data in the Typical column is at 3.3V, +25°C (PIC24F32KA3XX) or 5.0V, +25°C (PIC24FV32KA3XX) unless otherwise stated. Parameters are for design guidance only and are not tested. 2: Base IPD is measured with all peripherals and clocks shut down. All I/Os are configured as outputs and set low, PMSLP is set to ‘0’ and WDT, etc., are all switched off. 3: The  current is the additional current consumed when the module is enabled. This current should be added to the base IPD current. 4: This current applies to Sleep only. 5: This current applies to Sleep and Deep Sleep. 6: This current applies to Deep Sleep only.  2011-2017 Microchip Technology Inc. DS30009995E-page 271

PIC24FV32KA304 FAMILY TABLE 29-9: DC CHARACTERISTICS: I/O PIN INPUT SPECIFICATIONS Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX DC CHARACTERISTICS Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Param Sym Characteristic Min Typ(1) Max Units Conditions No. VIL Input Low Voltage(4) DI10 I/O Pins VSS — 0.2 VDD V DI15 MCLR VSS — 0.2 VDD V DI16 OSCI (XT mode) VSS — 0.2 VDD V DI17 OSCI (HS mode) VSS — 0.2 VDD V DI18 I/O Pins with I2C Buffer VSS — 0.3 VDD V SMBus is disabled DI19 I/O Pins with SMBus Buffer VSS — 0.8 V SMBus is enabled VIH Input High Voltage(4) DI20 I/O Pins: with Analog Functions 0.8 VDD — VDD V Digital Only 0.8 VDD — VDD V DI25 MCLR 0.8 VDD — VDD V DI26 OSCI (XT mode) 0.7 VDD — VDD V DI27 OSCI (HS mode) 0.7 VDD — VDD V DI28 I/O Pins with I2C Buffer: with Analog Functions 0.7 VDD — VDD V Digital Only 0.7 VDD — VDD V DI29 I/O Pins with SMBus 2.1 — VDD V 2.5V  VPIN  VDD DI30 ICNPU CNx Pull-up Current 50 250 500 A VDD = 3.3V, VPIN = VSS IIL Input Leakage Current(2,3) DI50 I/O Ports — 0.05 0.1 A VSS  VPIN  VDD, Pin at high-impedance DI55 MCLR — — 0.1 A VSS VPIN VDD DI56 OSCI — — 5 A VSS VPIN VDD, XT and HS modes Note 1: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated. Parameters are for design guidance only and are not tested. 2: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent normal operating conditions. Higher leakage current may be measured at different input voltages. 3: Negative current is defined as current sourced by the pin. 4: Refer to Table1-3 for I/O pin buffer types. DS30009995E-page 272  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY TABLE 29-10: DC CHARACTERISTICS: I/O PIN OUTPUT SPECIFICATIONS Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX DC CHARACTERISTICS Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Param Sym Characteristic Min Typ(1) Max Units Conditions No. VOL Output Low Voltage DO10 All I/O Pins — — 0.4 V IOL = 8.0 mA VDD = 4.5V — — 0.4 V IOL = 4.0 mA VDD = 3.6V — — 0.4 V IOL = 3.5 mA VDD = 2.0V DO16 OSC2/CLKO — — 0.4 V IOL = 2.0 mA VDD = 4.5V — — 0.4 V IOL = 1.2 mA VDD = 3.6V — — 0.4 V IOL = 0.4 mA VDD = 2.0V VOH Output High Voltage DO20 All I/O Pins 3.8 — — V IOH = -3.5 mA VDD = 4.5V 3 — — V IOH = -3.0 mA VDD = 3.6V 1.6 — — V IOH = -1.0 mA VDD = 2.0V DO26 OSC2/CLKO 3.8 — — V IOH = -2.0 mA VDD = 4.5V 3 — — V IOH = -1.0 mA VDD = 3.6V 1.6 — — V IOH = -0.5 mA VDD = 2.0V Note 1: Data in “Typ” column is at +25°C unless otherwise stated. Parameters are for design guidance only and are not tested. TABLE 29-11: DC CHARACTERISTICS: PROGRAM MEMORY Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX DC CHARACTERISTICS Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Param Sym Characteristic Min Typ(1) Max Units Conditions No. Program Flash Memory D130 EP Cell Endurance 10,000(2) — — E/W D131 VPR VDD for Read VMIN — 3.6 V VMIN = Minimum operating voltage D133A TIW Self-Timed Write Cycle — 2 — ms Time D134 TRETD Characteristic Retention 40 — — Year Provided no other specifications are violated D135 IDDP Supply Current During — 10 — mA Programming Note 1: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated. 2: Self-write and block erase.  2011-2017 Microchip Technology Inc. DS30009995E-page 273

PIC24FV32KA304 FAMILY TABLE 29-12: DC CHARACTERISTICS: DATA EEPROM MEMORY Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX DC CHARACTERISTICS Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Param Sym Characteristic Min Typ(1) Max Units Conditions No. Data EEPROM Memory D140 EPD Cell Endurance 100,000 — — E/W D141 VPRD VDD for Read VMIN — 3.6 V VMIN = Minimum operating voltage D143A TIWD Self-Timed Write Cycle — 4 — ms Time D143B TREF Number of Total — 10M — E/W Write/Erase Cycles Before Refresh D144 TRETDD Characteristic Retention 40 — — Year Provided no other specifications are violated D145 IDDPD Supply Current During — 7 — mA Programming Note 1: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated. TABLE 29-13: DC CHARACTERISTICS: COMPARATOR SPECIFICATIONS Operating Conditions: 2.0V < VDD < 3.6V, -40°C < TA < +125°C (unless otherwise stated) Param Symbol Characteristic Min Typ Max Units Comments No. D300 VIOFF Input Offset Voltage — 20 40 mV D301 VICM Input Common-Mode Voltage 0 — VDD V D302 CMRR Common-Mode Rejection 55 — — dB Ratio TABLE 29-14: DC CHARACTERISTICS: COMPARATOR VOLTAGE REFERENCE SPECIFICATIONS Operating Conditions: 2.0V < VDD < 3.6V, -40°C < TA < +125°C (unless otherwise stated) Param Symbol Characteristic Min Typ Max Units Comments No. VRD310 CVRES Resolution — — VDD/32 LSb VRD311 CVRAA Absolute Accuracy — — AVDD – 1.5 LSb VRD312 CVRUR Unit Resistor Value (R) — 2k —  DS30009995E-page 274  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY TABLE 29-15: INTERNAL VOLTAGE REGULATOR SPECIFICATIONS Operating Conditions: -40°C < TA < +125°C (unless otherwise stated) Param Symbol Characteristics Min Typ Max Units Comments No. DVR10 VBG Band Gap Reference Voltage 0.973 1.024 1.075 V DVR11 TBG Band Gap Reference Start-up — 1 — ms Time DVR20 VRGOUT Regulator Output Voltage 3.1 3.3 3.6 V -40°C < TA < +85°C 3.0 3.19 3.6 V -40°C < TA < +125°C DVR21 CEFC External Filter Capacitor Value 4.7 10 — F Series resistance < 3 Ohm recommended; < 5 Ohm is required. DVR30 VLVR Retention Regulator Output — 2.6 — V Voltage TABLE 29-16: CTMU CURRENT SOURCE SPECIFICATIONS Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX DC CHARACTERISTICS Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Param Sym Characteristic Min Typ(1) Max Units Comments Conditions No. DCT10 IOUT1 CTMU Current — 550 — nA CTMUICON<9:8> = 01 Source, Base Range DCT11 IOUT2 CTMU Current — 5.5 — A CTMUICON<9:8> = 10 Source, 10x Range 2.5V < VDD < VDDMAX DCT12 IOUT3 CTMU Current — 55 — A CTMUICON<9:8> = 11 Source, 100x Range DCT13 IOUT4 CTMU Current — 550 — A CTMUICON<9:8>=00 Source, 1000x Range (Note2) DCT20 VF Temperature Diode — .76 — V Forward Voltage DCT21 V Voltage Change per — 1.6 — mV/°C Degree Celsius Note 1: Nominal value at the center point of the current trim range (CTMUICON<7:2> = 000000). On PIC24F32KA parts, the current output is limited to the typical current value when IOUT4 is chosen. 2: Do not use this current range with a temperature sensing diode.  2011-2017 Microchip Technology Inc. DS30009995E-page 275

PIC24FV32KA304 FAMILY 29.2 AC Characteristics and Timing Parameters The information contained in this section defines the PIC24FV32KA304 family AC characteristics and timing parameters. TABLE 29-17: TEMPERATURE AND VOLTAGE SPECIFICATIONS – AC Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX AC CHARACTERISTICS Operating temperature: -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Operating voltage VDD range as described in Section29.1 “DC Characteristics”. FIGURE 29-3: LOAD CONDITIONS FOR DEVICE TIMING SPECIFICATIONS Load Condition 1 – For All Pins Except OSCO Load Condition 2 – For OSCO VDD/2 RL Pin CL VSS Pin CL RL = 464 CL = 50 pF for all pins except OSCO VSS 15 pF for OSCO output TABLE 29-18: CAPACITIVE LOADING REQUIREMENTS ON OUTPUT PINS Param Symbol Characteristic Min Typ(1) Max Units Conditions No. DO50 COSC2 OSCO/CLKO Pin — — 15 pF In XT and HS modes when the external clock is used to drive OSCI DO56 CIO All I/O Pins and OSCO — — 50 pF EC mode DO58 CB SCLx, SDAx — — 400 pF In I2C mode Note 1: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated. Parameters are for design guidance only and are not tested. DS30009995E-page 276  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY FIGURE 29-4: EXTERNAL CLOCK TIMING Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 OSCI OS20 OS30 OS30 OS31 OS31 OS25 CLKO OS40 OS41 TABLE 29-19: EXTERNAL CLOCK TIMING REQUIREMENTS Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX AC CHARACTERISTICS Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Param Sym Characteristic Min Typ(1) Max Units Conditions No. OS10 FOSC External CLKI Frequency DC — 32 MHz EC (External clocks allowed 4 — 8 MHz ECPLL only in EC mode) OS15 Oscillator Frequency 0.2 — 4 MHz XT 4 — 25 MHz HS 4 — 8 MHz XTPLL 31 — 33 kHz SOSC OS20 TOSC TOSC = 1/FOSC — — — — See Parameter OS10 for FOSC value OS25 TCY Instruction Cycle Time(2) 62.5 — DC ns OS30 TosL, External Clock in (OSCI) 0.45 x TOSC — — ns EC TosH High or Low Time OS31 TosR, External Clock in (OSCI) — — 20 ns EC TosF Rise or Fall Time OS40 TckR CLKO Rise Time(3) — 6 10 ns OS41 TckF CLKO Fall Time(3) — 6 10 ns Note 1: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated. Parameters are for design guidance only and are not tested. 2: The instruction cycle period (TCY) equals two times the input oscillator time base period. All specified values are based on characterization data for that particular oscillator type, under standard operating conditions, with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation and/or higher than expected current consumption. All devices are tested to operate at “Min.” values with an external clock applied to the OSCI/CLKI pin. When an external clock input is used, the “Max.” cycle time limit is “DC” (no clock) for all devices. 3: Measurements are taken in EC mode. The CLKO signal is measured on the OSCO pin. CLKO is low for the Q1-Q2 period (1/2 TCY) and high for the Q3-Q4 period (1/2 TCY).  2011-2017 Microchip Technology Inc. DS30009995E-page 277

PIC24FV32KA304 FAMILY TABLE 29-20: PLL CLOCK TIMING SPECIFICATIONS Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX AC CHARACTERISTICS Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Param Sym Characteristic(1) Min Typ(2) Max Units Conditions No. OS50 FPLLI PLL Input Frequency 4 — 8 MHz ECPLL, HSPLL modes, Range -40°C  TA  +85°C OS51 FSYS PLL Output Frequency 16 — 32 MHz -40°C  TA  +85°C Range OS52 TLOCK PLL Start-up Time — 1 2 ms (Lock Time) OS53 DCLK CLKO Stability (Jitter) -2 1 2 % Measured over a 100 ms period Note 1: These parameters are characterized but not tested in manufacturing. 2: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated. Parameters are for design guidance only and are not tested. TABLE 29-21: AC CHARACTERISTICS: INTERNAL RC ACCURACY Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX AC CHARACTERISTICS Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Param Characteristic Min Typ Max Units Conditions No. F20 Internal FRC Accuracy @ 8 MHz(1) FRC -2 — +2 % +25°C 3.0V  VDD  3.6V, F device 3.2V  VDD  5.5V, FV device -6 — +6 % -40°C  TA +85°C 1.8V  VDD  3.6V, F device 2.0V  VDD  5.5V, FV device LPRC @ 31 kHz(2) F21 -15 — 15 % Note 1: Frequency is calibrated at +25°C and 3.3V. The OSCTUN bits can be used to compensate for temperature drift. 2: The change of LPRC frequency as VDD changes. TABLE 29-22: INTERNAL RC OSCILLATOR SPECIFICATIONS Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX AC CHARACTERISTICS Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Param Sym Characteristic(1) Min Typ Max Units Conditions No. TFRC FRC Start-up Time — 5 — s TLPRC LPRC Start-up Time — 70 — s Note 1: These parameters are characterized but not tested in manufacturing. DS30009995E-page 278  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY FIGURE 29-5: CLKO AND I/O TIMING CHARACTERISTICS I/O Pin (Input) DI35 DI40 I/O Pin Old Value New Value (Output) DO31 DO32 Note: Refer to Figure29-3 for load conditions. TABLE 29-23: CLKO AND I/O TIMING REQUIREMENTS Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX AC CHARACTERISTICS Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Param Sym Characteristic Min Typ(1) Max Units Conditions No. DO31 TIOR Port Output Rise Time — 10 25 ns DO32 TIOF Port Output Fall Time — 10 25 ns DI35 TINP INTx Pin High or Low 20 — — ns Time (output) DI40 TRBP CNx High or Low Time 2 — — TCY (input) Note 1: Data in “Typ” column is at 3.3V, +25°C (PIC24F32KA3XX); 5.0V, +25°C (PIC24FV32KA3XX), unless otherwise stated.  2011-2017 Microchip Technology Inc. DS30009995E-page 279

PIC24FV32KA304 FAMILY TABLE 29-24: COMPARATOR TIMINGS Param Symbol Characteristic Min Typ Max Units Comments No. 300 TRESP Response Time*(1) — 150 400 ns 301 TMC2OV Comparator Mode Change to — — 10 s Output Valid* * Parameters are characterized but not tested. Note 1: Response time is measured with one comparator input at (VDD – 1.5)/2, while the other input transitions from VSS to VDD. TABLE 29-25: COMPARATOR VOLTAGE REFERENCE SETTLING TIME SPECIFICATIONS Param Symbol Characteristic Min Typ Max Units Comments No. VR310 TSET Settling Time(1) — — 10 s Note 1: Settling time is measured while CVRSS = 1 and the CVR<3:0> bits transition from ‘0000’ to ‘1111’. FIGURE 29-6: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER AND POWER-UP TIMER TIMING CHARACTERISTICS Vdd MCLR SY12 SY10 Internal POR PWRT SY11 SYSRST System Clock Watchdog Timer Reset SY20 SY13 SY13 I/O Pins SY35 DS30009995E-page 280  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY FIGURE 29-7: BROWN-OUT RESET CHARACTERISTICS Vddcore (Device not in Brown-out Reset) DC15 DC19 (Device in Brown-out Reset) SY25 Reset (Due to BOR) Tvreg + Trst TABLE 29-26: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER, POWER-UP TIMER, AND BROWN-OUT RESET TIMING REQUIREMENTS Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX AC CHARACTERISTICS Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Param Symbol Characteristic Min. Typ(1) Max. Units Conditions No. SY10 TmcL MCLR Pulse Width (low) 2 — — s SY11 TPWRT Power-up Timer Period 50 64 90 ms SY12 TPOR Power-on Reset Delay 1 5 10 s SY13 TIOZ I/O High-Impedance from — — 100 ns MCLR Low or Watchdog Timer Reset SY20 TWDT Watchdog Timer Time-out 0.85 1.0 1.15 ms 1.32 prescaler Period 3.4 4.0 4.6 ms 1:128 prescaler SY25 TBOR Brown-out Reset Pulse 1 — — s Width SY35 TFSCM Fail-Safe Clock Monitor — 2.0 2.3 s Delay SY45 TRST Internal State Reset Time — 5 — s SY50 TVREG On-Chip Voltage Regulator — 10 — s (Note2) Output Delay SY55 TLOCK PLL Start-up Time — 100 — s SY65 TOST Oscillator Start-up Time — 1024 — TOSC SY70 TDSWU Wake-up from Deep Sleep — 100 — s Based on full discharge of Time 10F capacitor on VCAP; includes TPOR and TRST SY71 TPM Program Memory Wake-up — 1 — s Sleep wake-up with Time PMSLP = 0 SY72 TLVR Retention Regulator — 250 — s Wake-up Time SY73 THVLD HVLD Interrupt Response — 2 — s Time Note 1: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated. 2: This applies to PIC24FV32KA3XX devices only.  2011-2017 Microchip Technology Inc. DS30009995E-page 281

PIC24FV32KA304 FAMILY FIGURE 29-8: TIMER1/2/3/4/5 EXTERNAL CLOCK INPUT TIMING TxCK Pin TtL TtH TtP TABLE 29-27: TIMER1/2/3/4/5 EXTERNAL CLOCK INPUT REQUIREMENTS Param. Symbol Characteristic Min Max Units Conditions No. TtH TxCK High Pulse Sync w/Prescaler TCY + 20 — ns Must also meet Time Async w/Prescaler 10 — ns Parameter Ttp Async Counter 20 — ns TtL TxCK Low Pulse Sync w/Prescaler TCY + 20 — ns Must also meet Time Async w/Prescaler 10 — ns Parameter Ttp Async Counter 20 — ns TtP TxCK External Input Sync w/Prescaler 2 * TCY + 40 — ns N = Prescale Value Period Async w/Prescaler Greater of: — ns (1, 4, 8, 16) 20 or 2 * TCY + 40 N Async Counter 40 — ns Delay for Input Edge Synchronous 1 2 TCY to Timer Increment Asynchronous — 20 ns FIGURE 29-9: INPUT CAPTURE x TIMINGS ICx Pin (Input Capture Mode) IC10 IC11 IC15 TABLE 29-28: INPUT CAPTURE x REQUIREMENTS Param. Symbol Characteristic Min Max Units Conditions No. IC10 TccL ICx Input Low Time – No Prescaler TCY + 20 — ns Must also meet Synchronous Timer With Prescaler 20 — ns Parameter IC15 IC11 TccH ICx Input Low Time – No Prescaler TCY + 20 — ns Must also meet Synchronous Timer With Prescaler 20 — ns Parameter IC15 IC15 TccP ICx Input Period – Synchronous Timer (2 * TCY/N) + 40 — ns N = prescale value (1, 4, 16) DS30009995E-page 282  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY FIGURE 29-10: OUTPUT COMPARE x TIMINGS OCx (Output Compare or PWM Mode) OC11 OC10 TABLE 29-29: OUTPUT CAPTURE REQUIREMENTS Param. Symbol Characteristic Min Max Units Conditions No. OC11 TCCR OC1 Output Rise Time — 10 ns — — ns OC10 TCCF OC1 Output Fall Time — 10 ns — — ns FIGURE 29-11: PWM MODULE TIMING REQUIREMENTS OC20 OCFx OC15 PWM TABLE 29-30: PWM TIMING REQUIREMENTS Param. Symbol Characteristic Min Typ† Max Units Conditions No. OC15 TFD Fault Input to PWM I/O — — 25 ns VDD = 3.0V, -40C to +125C Change OC20 TFH Fault Input Pulse Width 50 — — ns VDD = 3.0V, -40C to +125C † Data in “Typ” column is at 5V, +25C unless otherwise stated. These parameters are for design guidance only and are not tested.  2011-2017 Microchip Technology Inc. DS30009995E-page 283

PIC24FV32KA304 FAMILY FIGURE 29-12: I2C BUS START/STOP BITS TIMING CHARACTERISTICS (MASTER MODE) SCLx IM31 IM34 IM30 IM33 SDAx Start Stop Condition Condition Note: Refer to Figure29-3 for load conditions. TABLE 29-31: I2C BUS START/STOP BIT TIMING REQUIREMENTS (MASTER MODE) Standard Operating Conditions: 2.0V to 3.6V (unless otherwise stated) AC CHARACTERISTICS Operating temperature -40°C  TA  +85°C for Industrial) -40°C  TA  +125°C for Extended Param Symbol Characteristic Min(1) Max Units Conditions No. IM30 TSU:STA Start Condition 100 kHz mode TCY/2 (BRG + 1) — s Only relevant for Setup Time 400 kHz mode TCY/2 (BRG + 1) — s Repeated Start condition 1 MHz mode(2) TCY/2 (BRG + 1) — s IM31 THD:STA Start Condition 100 kHz mode TCY/2 (BRG + 1) — s After this period, the Hold Time 400 kHz mode TCY/2 (BRG + 1) — s first clock pulse is generated 1 MHz mode(2) TCY/2 (BRG + 1) — s IM33 TSU:STO Stop Condition 100 kHz mode TCY/2 (BRG + 1) — s Setup Time 400 kHz mode TCY/2 (BRG + 1) — s 1 MHz mode(2) TCY/2 (BRG + 1) — s IM34 THD:STO Stop Condition 100 kHz mode TCY/2 (BRG + 1) — ns Hold Time 400 kHz mode TCY/2 (BRG + 1) — ns 1 MHz mode(2) TCY/2 (BRG + 1) — ns Note 1: BRG is the value of the I2C Baud Rate Generator. Refer to Section 17.3 “Setting Baud Rate When Operating as a Bus Master” for details. 2: Maximum pin capacitance = 10 pF for all I2C pins (for 1 MHz mode only). DS30009995E-page 284  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY FIGURE 29-13: I2C BUS DATA TIMING CHARACTERISTICS (MASTER MODE) IM11 IM21 SCLx IM10 IM25 IM26 IM20 SDAx In IM45 IM40 SDAx Out Note: Refer to Figure29-3 for load conditions. TABLE 29-32: I2C BUS DATA TIMING REQUIREMENTS (MASTER MODE) Standard Operating Conditions: 2.0V to 3.6V (unless otherwise stated) AC CHARACTERISTICS Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Param Symbol Characteristic Min(1) Max Units Conditions No. IM10 TLO:SCL Clock Low Time 100 kHz mode TCY/2 (BRG + 1) — s 400 kHz mode TCY/2 (BRG + 1) — s 1 MHz mode(2) TCY/2 (BRG + 1) — s IM11 THI:SCL Clock High Time 100 kHz mode TCY/2 (BRG + 1) — s 400 kHz mode TCY/2 (BRG + 1) — s 1 MHz mode(2) TCY/2 (BRG + 1) — s IM20 TF:SCL SDAx and SCLx 100 kHz mode — 300 ns CB is specified to be Fall Time 400 kHz mode 20 + 0.1 CB 300 ns from 10 to 400 pF 1 MHz mode(2) — 100 ns IM21 TR:SCL SDAx and SCLx 100 kHz mode — 1000 ns CB is specified to be Rise Time 400 kHz mode 20 + 0.1 CB 300 ns from 10 to 400 pF 1 MHz mode(2) — 300 ns IM25 TSU:DAT Data Input 100 kHz mode 250 — ns Setup Time 400 kHz mode 100 — ns 1 MHz mode(2) 100 — ns IM26 THD:DAT Data Input 100 kHz mode 0 — ns Hold Time 400 kHz mode 0 0.9 s 1 MHz mode(2) 0 — ns IM40 TAA:SCL Output Valid 100 kHz mode — 3500 ns from Clock 400 kHz mode — 1000 ns 1 MHz mode(2) — — ns IM45 TBF:SDA Bus Free Time 100 kHz mode 4.7 — s Time the bus must be 400 kHz mode 1.3 — s free before a new 1 MHz mode(2) 0.5 — s transmission can start IM50 CB Bus Capacitive Loading — 400 pF Note 1: BRG is the value of the I2C Baud Rate Generator. Refer to Section 17.3 “Setting Baud Rate When Operating as a Bus Master” for details. 2: Maximum pin capacitance = 10 pF for all I2C pins (for 1 MHz mode only).  2011-2017 Microchip Technology Inc. DS30009995E-page 285

PIC24FV32KA304 FAMILY FIGURE 29-14: I2C BUS DATA TIMING CHARACTERISTICS (SLAVE MODE) IS11 IS21 IS10 SCLx IS25 IS20 IS26 SDAx In IS45 IS40 SDAx Out TABLE 29-33: I2C BUS DATA TIMING REQUIREMENTS (SLAVE MODE) Standard Operating Conditions: 2.0V to 3.6V (unless otherwise stated) AC CHARACTERISTICS Operating temperature -40°C  TA  +85°C (Industrial) -40°C  TA  +125°C (Extended) Param Symbol Characteristic Min Max Units Conditions No. IS10 TLO:SCL Clock Low Time 100 kHz mode 4.7 — s Device must operate at a minimum of 1.5 MHz 400 kHz mode 1.3 — s Device must operate at a minimum of 10 MHz 1 MHz mode(1) 0.5 — s IS11 THI:SCL Clock High Time 100 kHz mode 4.0 — s Device must operate at a minimum of 1.5 MHz 400 kHz mode 0.6 — s Device must operate at a minimum of 10 MHz 1 MHz mode(1) 0.5 — s IS20 TF:SCL SDAx and SCLx 100 kHz mode — 300 ns CB is specified to be from Fall Time 400 kHz mode 20 + 0.1 CB 300 ns 10 to 400 pF 1 MHz mode(1) — 100 ns IS21 TR:SCL SDAx and SCLx 100 kHz mode — 1000 ns CB is specified to be from Rise Time 400 kHz mode 20 + 0.1 CB 300 ns 10 to 400 pF 1 MHz mode(1) — 300 ns IS25 TSU:DAT Data Input 100 kHz mode 250 — ns Setup Time 400 kHz mode 100 — ns 1 MHz mode(1) 100 — ns IS26 THD:DAT Data Input 100 kHz mode 0 — ns Hold Time 400 kHz mode 0 0.9 s 1 MHz mode(1) 0 0.3 s IS40 TAA:SCL Output Valid From 100 kHz mode 0 3500 ns Clock 400 kHz mode 0 1000 ns 1 MHz mode(1) 0 350 ns IS45 TBF:SDA Bus Free Time 100 kHz mode 4.7 — s Time the bus must be free 400 kHz mode 1.3 — s before a new transmission can start 1 MHz mode(1) 0.5 — s IS50 CB Bus Capacitive Loading — 400 pF Note 1: Maximum pin capacitance = 10 pF for all I2C pins (for 1 MHz mode only). DS30009995E-page 286  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY FIGURE 29-15: I2C BUS START/STOP BITS TIMING CHARACTERISTICS (SLAVE MODE) SCLx IS31 IS34 IS30 IS33 SDAx Start Stop Condition Condition TABLE 29-34: I2C BUS START/STOP BITS TIMING REQUIREMENTS (SLAVE MODE) Standard Operating Conditions: 2.0V to 3.6V (unless otherwise stated) AC CHARACTERISTICS Operating temperature -40°C  TA  +85°C (Industrial) -40°C  TA  +125°C (Extended) Param Symbol Characteristic Min Max Units Conditions No. IS30 TSU:STA Start Condition 100 kHz mode 4.7 — s Only relevant for Repeated Setup Time 400 kHz mode 0.6 — s Start condition 1 MHz mode(1) 0.25 — s IS31 THD:STA Start Condition 100 kHz mode 4.0 — s After this period, the first Hold Time 400 kHz mode 0.6 — s clock pulse is generated 1 MHz mode(1) 0.25 — s IS33 TSU:STO Stop Condition 100 kHz mode 4.7 — s Setup Time 400 kHz mode 0.6 — s 1 MHz mode(1) 0.6 — s IS34 THD:STO Stop Condition 100 kHz mode 4000 — ns Hold Time 400 kHz mode 600 — ns 1 MHz mode(1) 250 — ns Note 1: Maximum pin capacitance = 10 pF for all I2C pins (for 1 MHz mode only).  2011-2017 Microchip Technology Inc. DS30009995E-page 287

PIC24FV32KA304 FAMILY FIGURE 29-16: UARTx BAUD RATE GENERATOR OUTPUT TIMING UxBRG + 1 * TCY TLW THW UxBCLK TBLD TBHD UxTX FIGURE 29-17: UARTx START BIT EDGE DETECTION UxBRG Any Value TCY Start bit Detected, UxBRG Started Cycle Clock TSETUP TSTDELAY UxRX TABLE 29-35: UARTx TIMING REQUIREMENTS Standard Operating Conditions: 2.0V to 3.6V (unless otherwise stated) AC CHARACTERISTICS Operating temperature -40°C  TA  +85°C (Industrial) -40°C  TA  +125°C (Extended) Symbol Characteristics Min Typ Max Units TLW UxBCLK High Time 20 TCY/2 — ns THW UxBCLK Low Time 20 (TCY * UXBRG) + TCY/2 — ns TBLD UxBCLK Falling Edge Delay from UxTX -50 — 50 ns TBHD UxBCLK Rising Edge Delay from UxTX TCY/2 – 50 — TCY/2 + 50 ns TWAK Minimum Low on UxRX Line to Cause — 1 — s Wake-up TCTS Minimum Low on UxCTS Line to Start Tcy — — ns Transmission TSETUP Start bit Falling Edge to System Clock Rising 3 — — ns Edge Setup Time TSTDELAY Maximum Delay in the Detection of the — — TCY + TSETUP ns Start bit Falling Edge DS30009995E-page 288  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY FIGURE 29-18: SPIx MODULE MASTER MODE TIMING CHARACTERISTICS (CKE = 0) SCKx (CKP = 0) SP11 SP10 SP21 SP20 SCKx (CKP = 1) SP35 SP20 SP21 SDOx MSb Bit 14 - - - - - -1 LSb SP31 SP30 SDIx MSb In Bit 14 - - - -1 LSb In SP40 SP41 TABLE 29-36: SPIx MASTER MODE TIMING REQUIREMENTS (CKE = 0) Standard Operating Conditions: 2.0V to 3.6V (unless otherwise stated) AC CHARACTERISTICS Operating temperature -40°C  TA  +85°C (Industrial) -40°C  TA  +125°C (Extended) Param Symbol Characteristic Min Typ(1) Max Units Conditions No. SP10 TscL SCKx Output Low Time(2) TCY/2 — — ns SP11 TscH SCKx Output High Time(2) TCY/2 — — ns SP20 TscF SCKx Output Fall Time(3) — 10 25 ns SP21 TscR SCKx Output Rise Time(3) — 10 25 ns SP30 TdoF SDOx Data Output Fall Time(3) — 10 25 ns SP31 TdoR SDOx Data Output Rise Time(3) — 10 25 ns SP35 TscH2doV, SDOx Data Output Valid after — — 30 ns TscL2doV SCKx Edge SP40 TdiV2scH, Setup Time of SDIx Data Input 20 — — ns TdiV2scL to SCKx Edge SP41 TscH2diL, Hold Time of SDIx Data Input 20 — — ns TscL2diL to SCKx Edge Note 1: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated. Parameters are for design guidance only and are not tested. 2: The minimum clock period for SCKx is 100 ns; therefore, the clock generated in Master mode must not violate this specification. 3: This assumes a 50 pF load on all SPIx pins.  2011-2017 Microchip Technology Inc. DS30009995E-page 289

PIC24FV32KA304 FAMILY FIGURE 29-19: SPIx MODULE MASTER MODE TIMING CHARACTERISTICS (CKE = 1) SP36 SCKx (CKP = 0) SP11 SP10 SP21 SP20 SCKx (CKP = 1) SP35 SP20 SP21 SDOx MSb Bit 14 - - - - - -1 LSb SP40 SP30,SP31 SDIx MSb In Bit 14 - - - -1 LSb In SP41 TABLE 29-37: SPIx MODULE MASTER MODE TIMING REQUIREMENTS (CKE = 1) Standard Operating Conditions: 2.0V to 3.6V (unless otherwise stated) AC CHARACTERISTICS Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Param Symbol Characteristic Min Typ(1) Max Units Conditions No. SP10 TscL SCKx Output Low Time(2) TCY/2 — — ns SP11 TscH SCKx Output High Time(2) TCY/2 — — ns SP20 TscF SCKx Output Fall Time(3) — 10 25 ns SP21 TscR SCKx Output Rise Time(3) — 10 25 ns SP30 TdoF SDOx Data Output Fall Time(3) — 10 25 ns SP31 TdoR SDOx Data Output Rise Time(3) — 10 25 ns SP35 TscH2doV, SDOx Data Output Valid after — — 30 ns TscL2doV SCKx Edge SP36 TdoV2sc, SDOx Data Output Setup to 30 — — ns TdoV2scL First SCKx Edge SP40 TdiV2scH, Setup Time of SDIx Data Input 20 — — ns TdiV2scL to SCKx Edge SP41 TscH2diL, Hold Time of SDIx Data Input 20 — — ns TscL2diL to SCKx Edge Note 1: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated. Parameters are for design guidance only and are not tested. 2: The minimum clock period for SCKx is 100 ns; therefore, the clock generated in Master mode must not violate this specification. 3: This assumes a 50 pF load on all SPIx pins. DS30009995E-page 290  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY FIGURE 29-20: SPIx MODULE SLAVE MODE TIMING CHARACTERISTICS (CKE = 0) SSx SP50 SP52 SCKx (CKP = 0) SP71 SP70 SP73 SP72 SCKx (CKP = 1) SP72 SP73 SP35 SDOx MSb Bit 14 - - - - - -1 LSb SP30,SP31 SP51 SDIx MSb In Bit 14 - - - -1 LSb In SP41 SP40 TABLE 29-38: SPIx MODULE SLAVE MODE TIMING REQUIREMENTS (CKE = 0) Standard Operating Conditions: 2.0V to 3.6V (unless otherwise stated) AC CHARACTERISTICS Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Param Symbol Characteristic Min Typ(1) Max Units Conditions No. SP70 TscL SCKx Input Low Time 30 — — ns SP71 TscH SCKx Input High Time 30 — — ns SP72 TscF SCKx Input Fall Time(2) — 10 25 ns SP73 TscR SCKx Input Rise Time(2) — 10 25 ns SP30 TdoF SDOx Data Output Fall Time(2) — 10 25 ns SP31 TdoR SDOx Data Output Rise Time(2) — 10 25 ns SP35 TscH2doV, SDOx Data Output Valid after — — 30 ns TscL2doV SCKx Edge SP40 TdiV2scH, Setup Time of SDIx Data Input 20 — — ns TdiV2scL to SCKx Edge SP41 TscH2diL, Hold Time of SDIx Data Input 20 — — ns TscL2diL to SCKx Edge SP50 TssL2scH, SSx to SCKx  or SCKx Input 120 — — ns TssL2scL SP51 TssH2doZ SSx  to SDOx Output High-Impedance(3) 10 — 50 ns SP52 TscH2ssH SSx after SCKx Edge 1.5 TCY + 40 — — ns TscL2ssH Note 1: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated. Parameters are for design guidance only and are not tested. 2: The minimum clock period for SCKx is 100 ns; therefore, the clock generated in Master mode must not violate this specification. 3: This assumes a 50 pF load on all SPIx pins.  2011-2017 Microchip Technology Inc. DS30009995E-page 291

PIC24FV32KA304 FAMILY FIGURE 29-21: SPIx MODULE SLAVE MODE TIMING CHARACTERISTICS (CKE = 1) SP60 SSx SP52 SP50 SCKx (CKP = 0) SP71 SP70 SP73 SP72 SCKx (CKP = 1) SP35 SP72 SP73 SP52 SDOx MSb Bit 14 - - - - - -1 LSb SP30,SP31 SP51 SDIx MSb In Bit 14 - - - -1 LSb In SP41 SP40 TABLE 29-39: SPIx MODULE SLAVE MODE TIMING REQUIREMENTS (CKE = 1) Standard Operating Conditions: 2.0V to 3.6V (unless otherwise stated) AC CHARACTERISTICS Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Param Symbol Characteristic Min Typ(1) Max Units Conditions No. SP70 TscL SCKx Input Low Time 30 — — ns SP71 TscH SCKx Input High Time 30 — — ns SP72 TscF SCKx Input Fall Time(2) — 10 25 ns SP73 TscR SCKx Input Rise Time(2) — 10 25 ns SP30 TdoF SDOx Data Output Fall Time(2) — 10 25 ns SP31 TdoR SDOx Data Output Rise Time(2) — 10 25 ns SP35 TscH2doV, SDOx Data Output Valid after SCKx Edge — — 30 ns TscL2doV SP40 TdiV2scH, Setup Time of SDIx Data Input to 20 — — ns TdiV2scL SCKx Edge SP41 TscH2diL, Hold Time of SDIx Data Input to 20 — — ns TscL2diL SCKx Edge SP50 TssL2scH, SSx  to SCKx  or SCKx  Input 120 — — ns TssL2scL SP51 TssH2doZ SSx  to SDOx Output High-Impedance(3) 10 — 50 ns SP52 TscH2ssH SSx  after SCKx Edge 1.5 TCY + 40 — — ns TscL2ssH SP60 TssL2doV SDOx Data Output Valid after SSx Edge — — 50 ns Note 1: Data in “Typ” column is at 3.3V, +25°C unless otherwise stated. Parameters are for design guidance only and are not tested. 2: The minimum clock period for SCKx is 100 ns; therefore, the clock generated in Master mode must not violate this specification. 3: This assumes a 50 pF load on all SPIx pins. DS30009995E-page 292  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY TABLE 29-40: A/D MODULE SPECIFICATIONS Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX AC CHARACTERISTICS Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Param Symbol Characteristic Min. Typ Max. Units Conditions No. Device Supply AD01 AVDD Module VDD Supply Greater of: — Lesser of: V PIC24FXXKA30X devices VDD – 0.3 or 1.8 VDD + 0.3 or 3.6 Greater of: — Lesser of: V PIC24FVXXKA30X VDD – 0.3 or 2.0 VDD + 0.3 or 5.5 devices AD02 AVSS Module VSS Supply VSS – 0.3 — VSS + 0.3 V Reference Inputs AD05 VREFH Reference Voltage High AVSS + 1.7 — AVDD V AD06 VREFL Reference Voltage Low AVSS — AVDD – 1.7 V AD07 VREF Absolute Reference AVSS – 0.3 — AVDD + 0.3 V Voltage AD08 IVREF Reference Voltage Input — 1.25 — mA Current AD09 ZVREF Reference Input — 10k —  Impedance Analog Input AD10 VINH-VINL Full-Scale Input Span VREFL — VREFH V (Note2) AD11 VIN Absolute Input Voltage AVSS – 0.3 — AVDD + 0.3 V AD12 VINL Absolute VINL Input AVSS – 0.3 — AVDD/2 V Voltage AD17 RIN Recommended — — 1k  12-bit Impedance of Analog Voltage Source A/D Accuracy AD20b NR Resolution — 12 — bits AD21b INL Integral Nonlinearity — ±1 ±9 LSb VINL = AVSS = VREFL = 0V, AVDD = VREFH = 5V AD22b DNL Differential Nonlinearity — ±1 ±5 LSb VINL = AVSS = VREFL = 0V, AVDD = VREFH = 5V AD23b GERR Gain Error — ±1 ±9 LSb VINL = AVSS = VREFL = 0V, AVDD = VREFH = 5V AD24b EOFF Offset Error — ±1 ±5 LSb VINL = AVSS = VREFL = 0V, AVDD = VREFH = 5V AD25b Monotonicity(1) — — — — Guaranteed Note 1: The A/D conversion result never decreases with an increase in the input voltage. 2: Measurements are taken with external VREF+ and VREF- used as the A/D voltage reference.  2011-2017 Microchip Technology Inc. DS30009995E-page 293

PIC24FV32KA304 FAMILY FIGURE 29-22: A/D CONVERSION TIMING BSET AD1CON1, SAMP BCLR AD1CON1, SAMP (Note 2) AD55 Q3/Q4 AD58 AD50 AD59 A/D CLK(1) A/D DATA 11 10 9 . . . . . . 2 1 0 ADC1BUFn OLD DATA NEW DATA AD1IF TCY SAMP SAMPLING STOPPED Note 1: If the A/D clock source is selected as RC, a time of TCY is added before the A/D clock starts. This allows the SLEEP instruction to be executed. 2: This is a minimal RC delay (typically 100 ns) which also disconnects the holding capacitor from the analog input. TABLE 29-41: A/D CONVERSION TIMING REQUIREMENTS(1) Standard Operating Conditions: 1.8V to 3.6V PIC24F32KA3XX 2.0V to 5.5V PIC24FV32KA3XX AC CHARACTERISTICS Operating temperature -40°C  TA  +85°C for Industrial -40°C  TA  +125°C for Extended Param Symbol Characteristic Min. Typ Max. Units Conditions No. Clock Parameters AD50 TAD A/D Clock Period 600 — — ns TCY = 75 ns, AD1CON3 in default state AD51 TRC A/D Internal RC Oscillator — 1.67 — µs Period Conversion Rate AD55 TCONV Conversion Time — 12 — TAD 10-bit results — 14 — TAD 12-bit results AD56 FCNV Throughput Rate — — 100 ksps AD57 TSAMP Sample Time — 1 — TAD AD58 TACQ Acquisition Time 750 — — ns (Note2) AD59 TSWC Switching Time from Convert — — (Note3) to Sample AD60 TDIS Discharge Time 12 — — TAD Clock Parameters AD61 TPSS Sample Start Delay from 2 — 3 TAD Setting Sample bit (SAMP) Note 1: Because the sample caps will eventually lose charge, clock rates below 10 kHz can affect linearity performance, especially at elevated temperatures. 2: The time for the holding capacitor to acquire the “New” input voltage when the voltage changes full scale after the conversion (VDD to VSS or VSS to VDD). 3: On the following cycle of the device clock. DS30009995E-page 294  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 30.0 DC AND AC CHARACTERISTICS GRAPHS AND TABLES Note: The graphs and tables provided following this note are a statistical summary based on a limited number of samples and are provided for informational purposes only. The performance characteristics listed herein are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified operating range (e.g., outside specified power supply range) and therefore, outside the warranted range. Data for VDD levels greater than 3.3V are applicable to PIC24FV32KA304 family devices only. 30.1 Characteristics for Industrial Temperature Devices (-40°C to +85°C) FIGURE 30-1: TYPICAL AND MAXIMUM IDD vs. FOSC (EC MODE, 2 MHz TO 32 MHz, -40°C TO +85°C) 20.0 18.0 16.0 5.5V Max 14.0 5.5 V Typ 12.0 3.3V Max A)10.0 3.3V Typ m 2.5V Max ( DD 8.0 2.5V Typ I 6.0 2.0V Max 2.0V Typ 4.0 2.0 0.0 2 6 10 14 18 22 26 30 Frequency (MHz) FIGURE 30-2: TYPICAL AND MAXIMUM IDD vs. FOSC (EC MODE, 1.95 kHz TO 1 MHz, +25°C) 550 450 5.5V Max 5.5V Typ A) µ 350 3.3V Max ( E 3.3V Typ L D II 2.0V Max 250 2.0V Typ 150 50 0 200 400 600 800 1000 Frequency (kHz)  2011-2017 Microchip Technology Inc. DS30009995E-page 295

PIC24FV32KA304 FAMILY FIGURE 30-3: TYPICAL AND MAXIMUM IIDLE vs. FREQUENCY (EC MODE, 2 MHz TO 32 MHz) 8.0 7.0 5.5V Max 6.0 5.5V Typ A) 5.0 3.3V Max m ( 3.3V Typ E 4.0 L 2.5V Max D II 3.0 2.5V Typ 2.0V Max 2.0 2.0V Typ 1.0 0.0 2 6 10 14 18 22 26 30 Frequency (MHz) FIGURE 30-4: TYPICAL AND MAXIMUM IIDLE vs. FREQUENCY (EC MODE, 1.95 kHz TO 1 MHz) 180 160 140 5.5V Max 5.5V Typ A) 120 3.3V Max µ ( E 3.3V Typ L 100 D II 2.0V Max 80 2.0V Typ 60 40 0.0 0.2 0.4 0.6 0.8 1.0 Frequency (MHz) DS30009995E-page 296  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY FIGURE 30-5: TYPICAL IDD vs. VDD (8 MHZ, EC MODE) 3.5 3.0 A) 2.5 -40C m ( 25C D D 60C I 2.0 85C 1.5 1.0 2 2.5 3 3.5 4 4.5 5 5.5 VDD FIGURE 30-6: TYPICAL IDD vs. VDD (FRC MODE) 3.5 3.0 -40 C A) 25 C m 2.5 (D 60 C D I 85 C 2.0 1.5 2 2.5 3 3.5 4 4.5 5 5.5 VDD  2011-2017 Microchip Technology Inc. DS30009995E-page 297

PIC24FV32KA304 FAMILY FIGURE 30-7: TYPICAL AND MAXIMUM IDD vs. TEMPERATURE (FRC MODE) 3.5 3.0 5.5V Max 5.5V Typ A) 3.3V Max m 2.5 ( D 3.3V Typ D I 2.0V Max 2.0V Typ 2.0 1.5 -40 -15 10 35 60 85 Temperature (°C) FIGURE 30-8: TYPICAL AND MAXIMUM IIDLE vs. VDD (FRC MODE) 1.10 1.00 -40C Typ -40C Max 0.90 25C Typ A) m 25C Max (D D 0.80 60C Typ I 60C Max 85C Typ 0.70 85C Max 0.60 2 2.5 3 3.5 4 4.5 5 5.5 VDD DS30009995E-page 298  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY FIGURE 30-9: TYPICAL AND MAXIMUM IIDLE vs. TEMPERATURE (FRC MODE) 1.10 1.00 5.5V Max A) 0.90 5.5V Typ m 3.3V Max ( D 3.3V Typ ID 0.80 2.0V Max 2.0V Typ 0.70 0.60 -40 -15 10 35 60 85 Temperature (°C) FIGURE 30-10: FRC FREQUENCY ACCURACY vs. VDD 0.5 0 ) % -0.5 r ( -40 C o r Er 25 C y -1 c 60 C n e u 85 C q -1.5 e r F -2 -2.5 2 2.5 3 3.5 4 4.5 5 5.5 VDD  2011-2017 Microchip Technology Inc. DS30009995E-page 299

PIC24FV32KA304 FAMILY FIGURE 30-11: FRC FREQUENCY ACCURACY vs. TEMPERATURE (2.0V  VDD  5.5V) 0.5 0 -0.5 %) -1 ( r o rr -1.5 E y c -2 n e u q -2.5 e r F -3 -3.5 -4 -40 -20 0 20 40 60 80 Temperature (°C) FIGURE 30-12: LPRC FREQUENCY ACCURACY vs. VDD 1 0 ) % r ( o -1 r r E y -40 C c -2 n 25 C e u q 60 C e -3 r F 85 C -4 -5 2 2.5 3 3.5 4 4.5 5 5.5 VDD DS30009995E-page 300  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY FIGURE 30-13: LPRC FREQUENCY ACCURACY vs. TEMPERATURE (2.0V  VDD  5.5V) 1 0 -1 %) ( r o -2 r r E y c -3 n e u eq -4 r F -5 -6 -40 -20 0 20 40 60 80 Temperature (°C) FIGURE 30-14: TYPICAL AND MAXIMUM IPD vs. VDD 3.5 3.0 -40C Typ 2.5 -40C Max 25C Typ 2.0 A) 25C Max µ I (PD 1.5 6600CC TMyapx 85C Typ 1.0 85C Max 0.5 0.0 2 2.5 3 3.5 4 4.5 5 5.5 VDD  2011-2017 Microchip Technology Inc. DS30009995E-page 301

PIC24FV32KA304 FAMILY FIGURE 30-15: TYPICAL AND MAXIMUM IPD vs. TEMPERATURE 2.0 1.5 5.5V Max 5.5V Typ A) 3.3V Max µ 1.0 (D 3.3V Typ P I 2.0V Max 2.0V Typ 0.5 0.0 -40 -15 10 35 60 85 Temperature (°C) FIGURE 30-16: TYPICAL AND MAXIMUM IPD vs. VDD (DEEP SLEEP MODE) 1500 1250 -40C Typ -40C Max 1000 25C Typ 25C Max A) 750 n 60C Typ ( D 60C Max P I 500 85C Typ 85C Max 250 0 2 2.5 3 3.5 4 4.5 5 5.5 VDD DS30009995E-page 302  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY FIGURE 30-17: TYPICAL AND MAXIMUM IPD vs. TEMPERATURE (DEEP SLEEP MODE) 1500 1250 5.5V Max 1000 5.5V Typ A) 3.3V Max n ( 750 D 3.3V Typ P I 2.0V Max 500 2.0V Typ 250 0 -40 -15 10 35 60 85 Temperature (°C) FIGURE 30-18: TYPICAL IBOR vs. VDD 10.0 9.0 8.0 7.0 -40 C 6.0 A) µ 25 C ( 5.0 OR 60 C B 4.0 I 85 C 3.0 2.0 1.0 0.0 2 2.5 3 3.5 4 4.5 5 5.5 VDD  2011-2017 Microchip Technology Inc. DS30009995E-page 303

PIC24FV32KA304 FAMILY FIGURE 30-19: TYPICAL IWDT vs. VDD 1.2 1.0 0.8 -40C A) 25C µ 0.6 ( T 60C D W 85C I 0.4 0.2 0.0 2 2.5 3 3.5 4 4.5 5 5.5 VDD FIGURE 30-20: TYPICAL IDSBOR vs. VDD 25 20 A) 15 -40 C n ( 25 C R O B 60 C DS 10 85 C I 5 0 2 2.5 3 3.5 4 4.5 5 5.5 VDD DS30009995E-page 304  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY FIGURE 30-21: TYPICAL IHLVD vs. VDD 10.0 9.0 8.0 -40C A) 7.0 µ 25C ( VLD 6.0 60C H 85C I 5.0 4.0 3.0 2 2.5 3 3.5 4 4.5 5 5.5 VDD FIGURE 30-22: TYPICAL IDSWDT vs. VDD 1.4 1.2 1.0 A) 85 C µ 0.8 ( 60 C T D W 25 C S 0.6 ID -40 C 0.4 0.2 0.0 2 2.5 3 3.5 4 4.5 5 5.5 VDD  2011-2017 Microchip Technology Inc. DS30009995E-page 305

PIC24FV32KA304 FAMILY FIGURE 30-23: TYPICAL VBOR vs. TEMPERATURE (BOR TRIP POINT 3) 1.88 1.86 ) V ( R O B 1.84 V 1.82 1.80 -40 -20 0 20 40 60 80 Temperature (°C) FIGURE 30-24: TYPICAL VOH vs. IOH (GENERAL PURPOSE I/O, AS A FUNCTION OF VDD) 6.0 5.0 4.0 V) 5.0V (H 3.0 3.3V O V 1.8V 2.0 1.0 0.0 0 -5 -10 -15 -20 -25 IOH (mA) DS30009995E-page 306  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY FIGURE 30-25: TYPICAL VOH vs. IOH (GENERAL PURPOSE I/O, AS A FUNCTION OF TEMPERATURE, 2.0V  VDD  5.5V) 3.5 3.0 -40 C 2.5 ) V 25 C ( H O 60 C V 2.0 85 C 1.5 1.0 0 -5 -10 -15 -20 -25 IOH (mA) FIGURE 30-26: TYPICAL VOL vs. IOL (GENERAL PURPOSE I/O, AS A FUNCTION OF VDD) 1.4 1.2 1.0 1.8 V V) 0.8 2.5 V (L VO 0.6 3.3 V 5.0 V 0.4 0.2 0.0 0 5 10 15 20 25 IOL (mA)  2011-2017 Microchip Technology Inc. DS30009995E-page 307

PIC24FV32KA304 FAMILY FIGURE 30-27: TYPICAL VOL vs. IOL (GENERAL PURPOSE I/O, AS A FUNCTION OF TEMPERATURE, 2.0V  VDD  5.5V) 1.2 1.0 0.8 -40 C ) V 25 C ( L 0.6 O 60 C V 85 C 0.4 0.2 0.0 0 5 10 15 20 25 IOL (mA) FIGURE 30-28: VIL/VIH vs. VDD (GENERAL PURPOSE I/O, TEMPERATURES AS NOTED) 3.5 3.0 Ensured Logic High 2.5 V) VVIHih T Typypiciaclal ( 2.0 H VVILIL T yTpyipcaiclal VI V/IL 1.5 Indeterminate VVIHIH M maxa -x4 0-4°C0 VVILIL M Mini n8 58°5CC 1.0 Ensured Logic Low 0.5 0.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 VDD DS30009995E-page 308  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY FIGURE 30-29: VIL/VIH vs. VDD (I2C, TEMPERATURES AS NOTED) 3.5 3.0 Ensured Logic High 2.5 V) VVIHI HT yMpaicxa l85C V (IH 2.0 Indeterminate VVIL IHTy Tpyicpaiclal V/IL 1.5 VVIHI LM Tayxp -i4c0a°lC VVIL ILM Mini n8 58°5CC 1.0 Ensured Logic Low 0.5 0.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 VDD FIGURE 30-30: VIL/VIH vs. VDD (OSCO, TEMPERATURES AS NOTED) 3.0 2.5 Ensured Logic High 2.0 ) VVIHIH T yMpaicxa l-40C V (H Indeterminate VI 1.5 VVILIH T yTpyicpaiclal /L VI VVIHIL M Tayxp -i4c0a°lC Ensured Logic Low 1.0 VVILIL M Mini n8 58°5CC 0.5 0.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 VDD  2011-2017 Microchip Technology Inc. DS30009995E-page 309

PIC24FV32KA304 FAMILY FIGURE 30-31: VIL/VIH vs. VDD (MCLR, TEMPERATURES AS NOTED) 3.0 2.5 Ensured Logic High 2.0 ) VVIIHH T Mypaixc a-l40C V ( V IH 1.5 Indeterminate VVIILH T Typypiciaclal /L VVIIHL MTyapx i-c4a0l°C VI 1.0 Ensured Logic Low VVIILL MMinin 8 855°CC 0.5 0.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 VDD FIGURE 30-32: TYPICAL BAND GAP VOLTAGE vs. VDD 1.035 1.030 1.025 -40C G 25C B V 60C 1.020 85C 1.015 1.010 2 2.5 3 3.5 4 4.5 5 5.5 VDD DS30009995E-page 310  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY FIGURE 30-33: TYPICAL BAND GAP VOLTAGE vs. TEMPERATURE (2.0V  VDD  5.5V) 1.04 1.03 G 1.02 B V 1.01 1.00 -40 -15 10 35 60 85 Temperature (°C) FIGURE 30-34: TYPICAL VOLTAGE REGULATOR OUTPUT vs. VDD 3.35 3.34 3.33 V) 3.32 ( t u -40 C p 3.31 ut 25 C O or 3.30 60 C t a 3.29 ul 85 C g e 3.28 R 3.27 3.26 3.25 2 2.5 3 3.5 4 4.5 5 5.5 VDD  2011-2017 Microchip Technology Inc. DS30009995E-page 311

PIC24FV32KA304 FAMILY FIGURE 30-35: TYPICAL VOLTAGE REGULATOR OUTPUT vs. TEMPERATURE 3.35 3.34 3.33 ) V t ( 3.32 u p ut 3.31 2.0V O r 3.30 3.3V o ulat 3.29 5.5V g 3.28 e R 3.27 3.26 3.25 -40 -15 10 35 60 85 Temperature (°C) FIGURE 30-36: HLVD TRIP POINT VOLTAGE vs. TEMPERATURE (HLVDL<3:0> = 0000, PIC24F32KA304 FAMILY DEVICES ONLY 1.90 Average Maximum 1.85 Minimum ) V ( nt 1.80 oi P p Tri 1.75 1.70 -40 -20 0 20 40 60 80 Temperature (°C) DS30009995E-page 312  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY FIGURE 30-37: TEMPERATURE SENSOR DIODE VOLTAGE vs. TEMPERATURE (2.0V  VDD  5.5V) 0.90 0.85 ) V 0.80 ( e g a olt 0.75 V e d o 0.70 Di 0.65 0.60 -40 -20 0 20 40 60 80 Temperature (°C) FIGURE 30-38: CTMU OUTPUT CURRENT vs. TEMPERATURE (IRNG<1:0> = 01, 2.0V  VDD  5.5V) 0.7 0.65 A) µ ( nt 0.6 e r r u C 0.55 0.5 -40 -20 0 20 40 60 80 Temperature (°C)  2011-2017 Microchip Technology Inc. DS30009995E-page 313

PIC24FV32KA304 FAMILY FIGURE 30-39: CTMU OUTPUT CURRENT vs. VDD (IRNG<1:0> = 01) 0.70 0.65 A) -40 C (µ 25 C nt 0.60 e 60 C r r u 85 C C 0.55 0.50 2 2.5 3 3.5 4 4.5 5 5.5 VDD DS30009995E-page 314  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 30.2 Characteristics for Extended Temperature Devices (-40°C to +125°C) Note: Data for VDD levels greater than 3.3V are applicable to PIC24FV32KA304 family devices only. FIGURE 30-40: TYPICAL AND MAXIMUM IIDLE vs. VDD (FRC MODE) A) m ( E L D II VDD FIGURE 30-41: TYPICAL AND MAXIMUM IIDLE vs. TEMPERATURE (FRC MODE) A) m ( E L D II Temperature (°C)  2011-2017 Microchip Technology Inc. DS30009995E-page 315

PIC24FV32KA304 FAMILY FIGURE 30-42: TYPICAL AND MAXIMUM IPD vs. VDD A) µ ( D P I VDD FIGURE 30-43: TYPICAL AND MAXIMUM IPD vs. TEMPERATURE A) µ (D P I Temperature (°C) DS30009995E-page 316  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY FIGURE 30-44: TYPICAL AND MAXIMUM IPD vs. VDD (DEEP SLEEP MODE) A) n ( nt e r r u C VDD FIGURE 30-45: TYPICAL AND MAXIMUM IPD vs. TEMPERATURE (DEEP SLEEP MODE) A) n ( nt e r r u C Temperature (°C)  2011-2017 Microchip Technology Inc. DS30009995E-page 317

PIC24FV32KA304 FAMILY FIGURE 30-46: TYPICAL IWDT vs. VDD A) µ ( T D W I VDD FIGURE 30-47: TYPICAL IDSBOR vs. VDD A) n ( R O B S D I VDD DS30009995E-page 318  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY FIGURE 30-48: TYPICAL IHLVD vs. VDD ) A µ (D V L H I VDD FIGURE 30-49: TYPICAL VOL vs. IOL (GENERAL I/O, 2.0V  VDD  5.5V) V) ( L O V IOL (MA)  2011-2017 Microchip Technology Inc. DS30009995E-page 319

PIC24FV32KA304 FAMILY FIGURE 30-50: TYPICAL VOH vs. IOH (GENERAL I/O, AS A FUNCTION OF TEMPERATURE, 2.0V  VDD  5.5V) V) ( H O V - - - - - IOH (mA) FIGURE 30-51: VIL/VIH vs. VDD (GENERAL PURPOSE I/O, TEMPERATURES AS NOTED) VIH Typical VIL Typical Ensured Logic High VIH Max -40°C VIL Min 125°C ) V (H Indeterminate VI /L VI Ensured Logic Low VDD DS30009995E-page 320  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY FIGURE 30-52: VIL/VIH vs. VDD (I2C, TEMPERATURES AS NOTED) VIH Typical VIL Typical Ensured Logic High VIH Max -40°C VIL Min 125°C ) V ( Indeterminate H VI /L VI Ensured Logic Low VDD FIGURE 30-53: VIL/VIH vs. VDD (OSCO, TEMPERATURES AS NOTED) VIH Typical VIL Typical Ensured Logic High VIH Max -40°C VIL Min 125°C ) V ( Indeterminate H VI /L VI Ensured Logic Low VDD  2011-2017 Microchip Technology Inc. DS30009995E-page 321

PIC24FV32KA304 FAMILY FIGURE 30-54: VIL/VIH vs. VDD (MCLR, TEMPERATURES AS NOTED) VIH Typical VIL Typical VIH Max -40°C Ensured Logic High VIL Min 125°C ) V ( H VI Indeterminate /L VI Ensured Logic Low VDD FIGURE 30-55: TYPICAL BAND GAP VOLTAGE vs. TEMPERATURE (2.0V  VDD  5.5V) V) (G B V Temperature (°C) DS30009995E-page 322  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY FIGURE 30-56: TYPICAL VOLTAGE REGULATOR OUTPUT vs. TEMPERATURE ) V t ( u p t u O r o t a ul g e R Temperature (°C)  2011-2017 Microchip Technology Inc. DS30009995E-page 323

PIC24FV32KA304 FAMILY NOTES: DS30009995E-page 324  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 31.0 PACKAGING INFORMATION 31.1 Package Marking Information 20-Lead PDIP (300 mil) Example XXXXXXXXXXXXXXXXX PIC24FV32KA301 XXXXXXXXXXXXXXXXX 1710017 YYWWNNN 28-Lead SPDIP (.300") Example XXXXXXXXXXXXXXXXX PIC24FV32KA302 XXXXXXXXXXXXXXXXX YYWWNNN 1710017 20-Lead SSOP (5.30 mm) Example XXXXXXXXXXX PIC24FV32KA XXXXXXXXXXX 301 YYWWNNN 1710017 28-Lead SSOP (5.30 mm) Example XXXXXXXXXXXX PIC24FV32KA XXXXXXXXXXXX 302 YYWWNNN 1710017 Legend: XX...X Customer-specific information Y Year code (last digit of calendar year) YY Year code (last 2 digits of calendar year) WW Week code (week of January 1 is week ‘01’) NNN Alphanumeric traceability code Note: In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information.  2011-2017 Microchip Technology Inc. DS30009995E-page 325

PIC24FV32KA304 FAMILY 20-Lead SOIC (7.50 mm) Example XXXXXXXXXXXXXX XXXXXXXXXXXXXX PIC24FV32KA301 XXXXXXXXXXXXXX 1710017 YYWWNNN 28-Lead SOIC (7.50 mm) Example XXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXX PIC24FV32KA302 XXXXXXXXXXXXXXXXXXXX 1710017 YYWWNNN 28-Lead QFN (6x6 mm) Example PIN 1 PIN 1 XXXXXXXX 24FV32KA XXXXXXXX 302 YYWWNNN 1710017 DS30009995E-page 326  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 4444--LLeeaadd QQFFNN ((88xx88xx00..99 mmmm)) Example PIN 1 PIN 1 XXXXXXXXXXXXXXXXXXXXXX PIC24FV32KA XXXXXXXXXXXXXXXXXXXXXX 304 XXXXXXXXXXXXXXXXXXXXXX 1710017 YYYYWWWWNNNNNN 44-Lead TQFP (10x10x1 mm) Example XXXXXXXXXX 24FV32KA XXXXXXXXXX 304 XXXXXXXXXX 1710017 YYWWNNN 48-Lead UQFN (6x6x0.5 mm) Example PIN 1 PIN 1 XXXXXXXX 24FV32KA XXXXXXXX 304 YYWWNNN 1710017  2011-2017 Microchip Technology Inc. DS30009995E-page 327

PIC24FV32KA304 FAMILY 31.2 Package Details The following sections give the technical details of the packages. (cid:2)(cid:3)(cid:4)(cid:5)(cid:6)(cid:7)(cid:8)(cid:9)(cid:10)(cid:11)(cid:7)(cid:12)(cid:13)(cid:14)(cid:15)(cid:9)(cid:16)(cid:17)(cid:7)(cid:11)(cid:9)(cid:18)(cid:19)(cid:4)(cid:5)(cid:14)(cid:19)(cid:6)(cid:9)(cid:20)(cid:10)(cid:21)(cid:9)(cid:22)(cid:9)(cid:23)(cid:3)(cid:3)(cid:9)(cid:24)(cid:14)(cid:11)(cid:9)(cid:25)(cid:26)(cid:8)(cid:27)(cid:9)(cid:28)(cid:10)(cid:16)(cid:18)(cid:10)(cid:29) (cid:30)(cid:26)(cid:13)(cid:6)(cid:31) 3(cid:22)(cid:21)(cid:14)&(cid:23)(cid:13)(cid:14)’(cid:22)!&(cid:14)(cid:20)"(cid:21)(cid:21)(cid:13)(cid:25)&(cid:14)(cid:10)(cid:11)(cid:20)4(cid:11)(cid:12)(cid:13)(cid:14)#(cid:21)(cid:11)*(cid:19)(cid:25)(cid:12)!((cid:14)(cid:10)(cid:26)(cid:13)(cid:11)!(cid:13)(cid:14)!(cid:13)(cid:13)(cid:14)&(cid:23)(cid:13)(cid:14)(cid:18)(cid:19)(cid:20)(cid:21)(cid:22)(cid:20)(cid:23)(cid:19)(cid:10)(cid:14)(cid:31)(cid:11)(cid:20)4(cid:11)(cid:12)(cid:19)(cid:25)(cid:12)(cid:14)(cid:3)(cid:10)(cid:13)(cid:20)(cid:19)%(cid:19)(cid:20)(cid:11)&(cid:19)(cid:22)(cid:25)(cid:14)(cid:26)(cid:22)(cid:20)(cid:11)&(cid:13)#(cid:14)(cid:11)&(cid:14) (cid:23)&&(cid:10)255***(cid:29)’(cid:19)(cid:20)(cid:21)(cid:22)(cid:20)(cid:23)(cid:19)(cid:10)(cid:29)(cid:20)(cid:22)’5(cid:10)(cid:11)(cid:20)4(cid:11)(cid:12)(cid:19)(cid:25)(cid:12) (cid:14) N NOTE1 E1 1 2 3 D E A A2 L c A1 b1 b e eB 6(cid:25)(cid:19)&! (cid:28)7,8.(cid:3) (cid:2)(cid:19)’(cid:13)(cid:25)!(cid:19)(cid:22)(cid:25)(cid:14)9(cid:19)’(cid:19)&! (cid:18)(cid:28)7 7:(cid:18) (cid:18)(cid:7); 7"’)(cid:13)(cid:21)(cid:14)(cid:22)%(cid:14)(cid:31)(cid:19)(cid:25)! 7 (cid:16)(cid:4) (cid:31)(cid:19)&(cid:20)(cid:23) (cid:13) (cid:29)(cid:30)(cid:4)(cid:4)(cid:14)1(cid:3), (cid:24)(cid:22)(cid:10)(cid:14)&(cid:22)(cid:14)(cid:3)(cid:13)(cid:11)&(cid:19)(cid:25)(cid:12)(cid:14)(cid:31)(cid:26)(cid:11)(cid:25)(cid:13) (cid:7) < < (cid:29)(cid:16)(cid:30)(cid:4) (cid:18)(cid:22)(cid:26)#(cid:13)#(cid:14)(cid:31)(cid:11)(cid:20)4(cid:11)(cid:12)(cid:13)(cid:14)(cid:24)(cid:23)(cid:19)(cid:20)4(cid:25)(cid:13)!! (cid:7)(cid:16) (cid:29)(cid:30)(cid:30)(cid:15) (cid:29)(cid:30)-(cid:4) (cid:29)(cid:30)(cid:6)(cid:15) 1(cid:11)!(cid:13)(cid:14)&(cid:22)(cid:14)(cid:3)(cid:13)(cid:11)&(cid:19)(cid:25)(cid:12)(cid:14)(cid:31)(cid:26)(cid:11)(cid:25)(cid:13) (cid:7)(cid:30) (cid:29)(cid:4)(cid:30)(cid:15) < < (cid:3)(cid:23)(cid:22)"(cid:26)#(cid:13)(cid:21)(cid:14)&(cid:22)(cid:14)(cid:3)(cid:23)(cid:22)"(cid:26)#(cid:13)(cid:21)(cid:14)=(cid:19)#&(cid:23) . (cid:29)-(cid:4)(cid:4) (cid:29)-(cid:30)(cid:4) (cid:29)-(cid:16)(cid:15) (cid:18)(cid:22)(cid:26)#(cid:13)#(cid:14)(cid:31)(cid:11)(cid:20)4(cid:11)(cid:12)(cid:13)(cid:14)=(cid:19)#&(cid:23) .(cid:30) (cid:29)(cid:16)(cid:5)(cid:4) (cid:29)(cid:16)(cid:15)(cid:4) (cid:29)(cid:16)>(cid:4) : (cid:13)(cid:21)(cid:11)(cid:26)(cid:26)(cid:14)9(cid:13)(cid:25)(cid:12)&(cid:23) (cid:2) (cid:29)(cid:6)>(cid:4) (cid:30)(cid:29)(cid:4)-(cid:4) (cid:30)(cid:29)(cid:4)?(cid:4) (cid:24)(cid:19)(cid:10)(cid:14)&(cid:22)(cid:14)(cid:3)(cid:13)(cid:11)&(cid:19)(cid:25)(cid:12)(cid:14)(cid:31)(cid:26)(cid:11)(cid:25)(cid:13) 9 (cid:29)(cid:30)(cid:30)(cid:15) (cid:29)(cid:30)-(cid:4) (cid:29)(cid:30)(cid:15)(cid:4) 9(cid:13)(cid:11)#(cid:14)(cid:24)(cid:23)(cid:19)(cid:20)4(cid:25)(cid:13)!! (cid:20) (cid:29)(cid:4)(cid:4)> (cid:29)(cid:4)(cid:30)(cid:4) (cid:29)(cid:4)(cid:30)(cid:15) 6(cid:10)(cid:10)(cid:13)(cid:21)(cid:14)9(cid:13)(cid:11)#(cid:14)=(cid:19)#&(cid:23) )(cid:30) (cid:29)(cid:4)(cid:5)(cid:15) (cid:29)(cid:4)?(cid:4) (cid:29)(cid:4)(cid:17)(cid:4) 9(cid:22)*(cid:13)(cid:21)(cid:14)9(cid:13)(cid:11)#(cid:14)=(cid:19)#&(cid:23) ) (cid:29)(cid:4)(cid:30)(cid:5) (cid:29)(cid:4)(cid:30)> (cid:29)(cid:4)(cid:16)(cid:16) : (cid:13)(cid:21)(cid:11)(cid:26)(cid:26)(cid:14)(cid:8)(cid:22)*(cid:14)(cid:3)(cid:10)(cid:11)(cid:20)(cid:19)(cid:25)(cid:12)(cid:14)(cid:14)+ (cid:13)1 < < (cid:29)(cid:5)-(cid:4) (cid:30)(cid:26)(cid:13)(cid:6)(cid:12)(cid:31) (cid:30)(cid:29) (cid:31)(cid:19)(cid:25)(cid:14)(cid:30)(cid:14) (cid:19)!"(cid:11)(cid:26)(cid:14)(cid:19)(cid:25)#(cid:13)$(cid:14)%(cid:13)(cid:11)&"(cid:21)(cid:13)(cid:14)’(cid:11)(cid:27)(cid:14) (cid:11)(cid:21)(cid:27)((cid:14))"&(cid:14)’"!&(cid:14))(cid:13)(cid:14)(cid:26)(cid:22)(cid:20)(cid:11)&(cid:13)#(cid:14)*(cid:19)&(cid:23)(cid:19)(cid:25)(cid:14)&(cid:23)(cid:13)(cid:14)(cid:23)(cid:11)&(cid:20)(cid:23)(cid:13)#(cid:14)(cid:11)(cid:21)(cid:13)(cid:11)(cid:29) (cid:16)(cid:29) +(cid:14)(cid:3)(cid:19)(cid:12)(cid:25)(cid:19)%(cid:19)(cid:20)(cid:11)(cid:25)&(cid:14),(cid:23)(cid:11)(cid:21)(cid:11)(cid:20)&(cid:13)(cid:21)(cid:19)!&(cid:19)(cid:20)(cid:29) -(cid:29) (cid:2)(cid:19)’(cid:13)(cid:25)!(cid:19)(cid:22)(cid:25)!(cid:14)(cid:2)(cid:14)(cid:11)(cid:25)#(cid:14).(cid:30)(cid:14)#(cid:22)(cid:14)(cid:25)(cid:22)&(cid:14)(cid:19)(cid:25)(cid:20)(cid:26)"#(cid:13)(cid:14)’(cid:22)(cid:26)#(cid:14)%(cid:26)(cid:11)!(cid:23)(cid:14)(cid:22)(cid:21)(cid:14)(cid:10)(cid:21)(cid:22)&(cid:21)"!(cid:19)(cid:22)(cid:25)!(cid:29)(cid:14)(cid:18)(cid:22)(cid:26)#(cid:14)%(cid:26)(cid:11)!(cid:23)(cid:14)(cid:22)(cid:21)(cid:14)(cid:10)(cid:21)(cid:22)&(cid:21)"!(cid:19)(cid:22)(cid:25)!(cid:14)!(cid:23)(cid:11)(cid:26)(cid:26)(cid:14)(cid:25)(cid:22)&(cid:14)(cid:13)$(cid:20)(cid:13)(cid:13)#(cid:14)(cid:29)(cid:4)(cid:30)(cid:4)/(cid:14)(cid:10)(cid:13)(cid:21)(cid:14)!(cid:19)#(cid:13)(cid:29) (cid:5)(cid:29) (cid:2)(cid:19)’(cid:13)(cid:25)!(cid:19)(cid:22)(cid:25)(cid:19)(cid:25)(cid:12)(cid:14)(cid:11)(cid:25)#(cid:14)&(cid:22)(cid:26)(cid:13)(cid:21)(cid:11)(cid:25)(cid:20)(cid:19)(cid:25)(cid:12)(cid:14)(cid:10)(cid:13)(cid:21)(cid:14)(cid:7)(cid:3)(cid:18).(cid:14)0(cid:30)(cid:5)(cid:29)(cid:15)(cid:18)(cid:29) 1(cid:3),2 1(cid:11)!(cid:19)(cid:20)(cid:14)(cid:2)(cid:19)’(cid:13)(cid:25)!(cid:19)(cid:22)(cid:25)(cid:29)(cid:14)(cid:24)(cid:23)(cid:13)(cid:22)(cid:21)(cid:13)&(cid:19)(cid:20)(cid:11)(cid:26)(cid:26)(cid:27)(cid:14)(cid:13)$(cid:11)(cid:20)&(cid:14) (cid:11)(cid:26)"(cid:13)(cid:14)!(cid:23)(cid:22)*(cid:25)(cid:14)*(cid:19)&(cid:23)(cid:22)"&(cid:14)&(cid:22)(cid:26)(cid:13)(cid:21)(cid:11)(cid:25)(cid:20)(cid:13)!(cid:29) (cid:18)(cid:19)(cid:20)(cid:21)(cid:22)(cid:20)(cid:23)(cid:19)(cid:10)(cid:24)(cid:13)(cid:20)(cid:23)(cid:25)(cid:22)(cid:26)(cid:22)(cid:12)(cid:27)(cid:2)(cid:21)(cid:11)*(cid:19)(cid:25)(cid:12),(cid:4)(cid:5)(cid:9)(cid:4)(cid:30)(cid:6)1 DS30009995E-page 328  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY (cid:2) (cid:4)(cid:5)(cid:6)(cid:7)(cid:8)(cid:9)!"(cid:14)(cid:19)(cid:19)(cid:27)(cid:9)(cid:10)(cid:11)(cid:7)(cid:12)(cid:13)(cid:14)(cid:15)(cid:9)(cid:16)(cid:17)(cid:7)(cid:11)(cid:9)(cid:18)(cid:19)(cid:4)(cid:5)(cid:14)(cid:19)(cid:6)(cid:9)(cid:20)!(cid:10)(cid:21)(cid:9)(cid:22)(cid:9)(cid:23)(cid:3)(cid:3)(cid:9)(cid:24)(cid:14)(cid:11)(cid:9)(cid:25)(cid:26)(cid:8)(cid:27)(cid:9)(cid:28)!(cid:10)(cid:16)(cid:18)(cid:10)(cid:29) (cid:30)(cid:26)(cid:13)(cid:6)(cid:31) 3(cid:22)(cid:21)(cid:14)&(cid:23)(cid:13)(cid:14)’(cid:22)!&(cid:14)(cid:20)"(cid:21)(cid:21)(cid:13)(cid:25)&(cid:14)(cid:10)(cid:11)(cid:20)4(cid:11)(cid:12)(cid:13)(cid:14)#(cid:21)(cid:11)*(cid:19)(cid:25)(cid:12)!((cid:14)(cid:10)(cid:26)(cid:13)(cid:11)!(cid:13)(cid:14)!(cid:13)(cid:13)(cid:14)&(cid:23)(cid:13)(cid:14)(cid:18)(cid:19)(cid:20)(cid:21)(cid:22)(cid:20)(cid:23)(cid:19)(cid:10)(cid:14)(cid:31)(cid:11)(cid:20)4(cid:11)(cid:12)(cid:19)(cid:25)(cid:12)(cid:14)(cid:3)(cid:10)(cid:13)(cid:20)(cid:19)%(cid:19)(cid:20)(cid:11)&(cid:19)(cid:22)(cid:25)(cid:14)(cid:26)(cid:22)(cid:20)(cid:11)&(cid:13)#(cid:14)(cid:11)&(cid:14) (cid:23)&&(cid:10)255***(cid:29)’(cid:19)(cid:20)(cid:21)(cid:22)(cid:20)(cid:23)(cid:19)(cid:10)(cid:29)(cid:20)(cid:22)’5(cid:10)(cid:11)(cid:20)4(cid:11)(cid:12)(cid:19)(cid:25)(cid:12) N NOTE1 E1 1 2 3 D E A A2 L c A1 b1 b e eB 6(cid:25)(cid:19)&! (cid:28)7,8.(cid:3) (cid:2)(cid:19)’(cid:13)(cid:25)!(cid:19)(cid:22)(cid:25)(cid:14)9(cid:19)’(cid:19)&! (cid:18)(cid:28)7 7:(cid:18) (cid:18)(cid:7); 7"’)(cid:13)(cid:21)(cid:14)(cid:22)%(cid:14)(cid:31)(cid:19)(cid:25)! 7 (cid:16)> (cid:31)(cid:19)&(cid:20)(cid:23) (cid:13) (cid:29)(cid:30)(cid:4)(cid:4)(cid:14)1(cid:3), (cid:24)(cid:22)(cid:10)(cid:14)&(cid:22)(cid:14)(cid:3)(cid:13)(cid:11)&(cid:19)(cid:25)(cid:12)(cid:14)(cid:31)(cid:26)(cid:11)(cid:25)(cid:13) (cid:7) < < (cid:29)(cid:16)(cid:4)(cid:4) (cid:18)(cid:22)(cid:26)#(cid:13)#(cid:14)(cid:31)(cid:11)(cid:20)4(cid:11)(cid:12)(cid:13)(cid:14)(cid:24)(cid:23)(cid:19)(cid:20)4(cid:25)(cid:13)!! (cid:7)(cid:16) (cid:29)(cid:30)(cid:16)(cid:4) (cid:29)(cid:30)-(cid:15) (cid:29)(cid:30)(cid:15)(cid:4) 1(cid:11)!(cid:13)(cid:14)&(cid:22)(cid:14)(cid:3)(cid:13)(cid:11)&(cid:19)(cid:25)(cid:12)(cid:14)(cid:31)(cid:26)(cid:11)(cid:25)(cid:13) (cid:7)(cid:30) (cid:29)(cid:4)(cid:30)(cid:15) < < (cid:3)(cid:23)(cid:22)"(cid:26)#(cid:13)(cid:21)(cid:14)&(cid:22)(cid:14)(cid:3)(cid:23)(cid:22)"(cid:26)#(cid:13)(cid:21)(cid:14)=(cid:19)#&(cid:23) . (cid:29)(cid:16)(cid:6)(cid:4) (cid:29)-(cid:30)(cid:4) (cid:29)--(cid:15) (cid:18)(cid:22)(cid:26)#(cid:13)#(cid:14)(cid:31)(cid:11)(cid:20)4(cid:11)(cid:12)(cid:13)(cid:14)=(cid:19)#&(cid:23) .(cid:30) (cid:29)(cid:16)(cid:5)(cid:4) (cid:29)(cid:16)>(cid:15) (cid:29)(cid:16)(cid:6)(cid:15) : (cid:13)(cid:21)(cid:11)(cid:26)(cid:26)(cid:14)9(cid:13)(cid:25)(cid:12)&(cid:23) (cid:2) (cid:30)(cid:29)-(cid:5)(cid:15) (cid:30)(cid:29)-?(cid:15) (cid:30)(cid:29)(cid:5)(cid:4)(cid:4) (cid:24)(cid:19)(cid:10)(cid:14)&(cid:22)(cid:14)(cid:3)(cid:13)(cid:11)&(cid:19)(cid:25)(cid:12)(cid:14)(cid:31)(cid:26)(cid:11)(cid:25)(cid:13) 9 (cid:29)(cid:30)(cid:30)(cid:4) (cid:29)(cid:30)-(cid:4) (cid:29)(cid:30)(cid:15)(cid:4) 9(cid:13)(cid:11)#(cid:14)(cid:24)(cid:23)(cid:19)(cid:20)4(cid:25)(cid:13)!! (cid:20) (cid:29)(cid:4)(cid:4)> (cid:29)(cid:4)(cid:30)(cid:4) (cid:29)(cid:4)(cid:30)(cid:15) 6(cid:10)(cid:10)(cid:13)(cid:21)(cid:14)9(cid:13)(cid:11)#(cid:14)=(cid:19)#&(cid:23) )(cid:30) (cid:29)(cid:4)(cid:5)(cid:4) (cid:29)(cid:4)(cid:15)(cid:4) (cid:29)(cid:4)(cid:17)(cid:4) 9(cid:22)*(cid:13)(cid:21)(cid:14)9(cid:13)(cid:11)#(cid:14)=(cid:19)#&(cid:23) ) (cid:29)(cid:4)(cid:30)(cid:5) (cid:29)(cid:4)(cid:30)> (cid:29)(cid:4)(cid:16)(cid:16) : (cid:13)(cid:21)(cid:11)(cid:26)(cid:26)(cid:14)(cid:8)(cid:22)*(cid:14)(cid:3)(cid:10)(cid:11)(cid:20)(cid:19)(cid:25)(cid:12)(cid:14)(cid:14)+ (cid:13)1 < < (cid:29)(cid:5)-(cid:4) (cid:30)(cid:26)(cid:13)(cid:6)(cid:12)(cid:31) (cid:30)(cid:29) (cid:31)(cid:19)(cid:25)(cid:14)(cid:30)(cid:14) (cid:19)!"(cid:11)(cid:26)(cid:14)(cid:19)(cid:25)#(cid:13)$(cid:14)%(cid:13)(cid:11)&"(cid:21)(cid:13)(cid:14)’(cid:11)(cid:27)(cid:14) (cid:11)(cid:21)(cid:27)((cid:14))"&(cid:14)’"!&(cid:14))(cid:13)(cid:14)(cid:26)(cid:22)(cid:20)(cid:11)&(cid:13)#(cid:14)*(cid:19)&(cid:23)(cid:19)(cid:25)(cid:14)&(cid:23)(cid:13)(cid:14)(cid:23)(cid:11)&(cid:20)(cid:23)(cid:13)#(cid:14)(cid:11)(cid:21)(cid:13)(cid:11)(cid:29) (cid:16)(cid:29) +(cid:14)(cid:3)(cid:19)(cid:12)(cid:25)(cid:19)%(cid:19)(cid:20)(cid:11)(cid:25)&(cid:14),(cid:23)(cid:11)(cid:21)(cid:11)(cid:20)&(cid:13)(cid:21)(cid:19)!&(cid:19)(cid:20)(cid:29) -(cid:29) (cid:2)(cid:19)’(cid:13)(cid:25)!(cid:19)(cid:22)(cid:25)!(cid:14)(cid:2)(cid:14)(cid:11)(cid:25)#(cid:14).(cid:30)(cid:14)#(cid:22)(cid:14)(cid:25)(cid:22)&(cid:14)(cid:19)(cid:25)(cid:20)(cid:26)"#(cid:13)(cid:14)’(cid:22)(cid:26)#(cid:14)%(cid:26)(cid:11)!(cid:23)(cid:14)(cid:22)(cid:21)(cid:14)(cid:10)(cid:21)(cid:22)&(cid:21)"!(cid:19)(cid:22)(cid:25)!(cid:29)(cid:14)(cid:18)(cid:22)(cid:26)#(cid:14)%(cid:26)(cid:11)!(cid:23)(cid:14)(cid:22)(cid:21)(cid:14)(cid:10)(cid:21)(cid:22)&(cid:21)"!(cid:19)(cid:22)(cid:25)!(cid:14)!(cid:23)(cid:11)(cid:26)(cid:26)(cid:14)(cid:25)(cid:22)&(cid:14)(cid:13)$(cid:20)(cid:13)(cid:13)#(cid:14)(cid:29)(cid:4)(cid:30)(cid:4)/(cid:14)(cid:10)(cid:13)(cid:21)(cid:14)!(cid:19)#(cid:13)(cid:29) (cid:5)(cid:29) (cid:2)(cid:19)’(cid:13)(cid:25)!(cid:19)(cid:22)(cid:25)(cid:19)(cid:25)(cid:12)(cid:14)(cid:11)(cid:25)#(cid:14)&(cid:22)(cid:26)(cid:13)(cid:21)(cid:11)(cid:25)(cid:20)(cid:19)(cid:25)(cid:12)(cid:14)(cid:10)(cid:13)(cid:21)(cid:14)(cid:7)(cid:3)(cid:18).(cid:14)0(cid:30)(cid:5)(cid:29)(cid:15)(cid:18)(cid:29) 1(cid:3),2 1(cid:11)!(cid:19)(cid:20)(cid:14)(cid:2)(cid:19)’(cid:13)(cid:25)!(cid:19)(cid:22)(cid:25)(cid:29)(cid:14)(cid:24)(cid:23)(cid:13)(cid:22)(cid:21)(cid:13)&(cid:19)(cid:20)(cid:11)(cid:26)(cid:26)(cid:27)(cid:14)(cid:13)$(cid:11)(cid:20)&(cid:14) (cid:11)(cid:26)"(cid:13)(cid:14)!(cid:23)(cid:22)*(cid:25)(cid:14)*(cid:19)&(cid:23)(cid:22)"&(cid:14)&(cid:22)(cid:26)(cid:13)(cid:21)(cid:11)(cid:25)(cid:20)(cid:13)!(cid:29) (cid:18)(cid:19)(cid:20)(cid:21)(cid:22)(cid:20)(cid:23)(cid:19)(cid:10)(cid:24)(cid:13)(cid:20)(cid:23)(cid:25)(cid:22)(cid:26)(cid:22)(cid:12)(cid:27)(cid:2)(cid:21)(cid:11)*(cid:19)(cid:25)(cid:12),(cid:4)(cid:5)(cid:9)(cid:4)(cid:17)(cid:4)1  2011-2017 Microchip Technology Inc. DS30009995E-page 329

PIC24FV32KA304 FAMILY (cid:2)(cid:3)(cid:4)(cid:5)(cid:6)(cid:7)(cid:8)(cid:9)(cid:10)(cid:11)(cid:7)(cid:12)(cid:13)(cid:14)(cid:15)(cid:9)!#$(cid:14)(cid:19)"(cid:9)!(cid:24)(cid:7)(cid:11)(cid:11)(cid:9)%(cid:17)(cid:13)(cid:11)(cid:14)(cid:19)(cid:6)(cid:9)(cid:20)!!(cid:21)(cid:9)(cid:22)(cid:9)&’(cid:23)(cid:3)(cid:9)(cid:24)(cid:24)(cid:9)(cid:25)(cid:26)(cid:8)(cid:27)(cid:9)(cid:28)!!%(cid:10)(cid:29)(cid:9) (cid:30)(cid:26)(cid:13)(cid:6)(cid:31) 3(cid:22)(cid:21)(cid:14)&(cid:23)(cid:13)(cid:14)’(cid:22)!&(cid:14)(cid:20)"(cid:21)(cid:21)(cid:13)(cid:25)&(cid:14)(cid:10)(cid:11)(cid:20)4(cid:11)(cid:12)(cid:13)(cid:14)#(cid:21)(cid:11)*(cid:19)(cid:25)(cid:12)!((cid:14)(cid:10)(cid:26)(cid:13)(cid:11)!(cid:13)(cid:14)!(cid:13)(cid:13)(cid:14)&(cid:23)(cid:13)(cid:14)(cid:18)(cid:19)(cid:20)(cid:21)(cid:22)(cid:20)(cid:23)(cid:19)(cid:10)(cid:14)(cid:31)(cid:11)(cid:20)4(cid:11)(cid:12)(cid:19)(cid:25)(cid:12)(cid:14)(cid:3)(cid:10)(cid:13)(cid:20)(cid:19)%(cid:19)(cid:20)(cid:11)&(cid:19)(cid:22)(cid:25)(cid:14)(cid:26)(cid:22)(cid:20)(cid:11)&(cid:13)#(cid:14)(cid:11)&(cid:14) (cid:23)&&(cid:10)255***(cid:29)’(cid:19)(cid:20)(cid:21)(cid:22)(cid:20)(cid:23)(cid:19)(cid:10)(cid:29)(cid:20)(cid:22)’5(cid:10)(cid:11)(cid:20)4(cid:11)(cid:12)(cid:19)(cid:25)(cid:12) D N E E1 NOTE1 1 2 e b c A A2 φ A1 L1 L 6(cid:25)(cid:19)&! (cid:18)(cid:28)99(cid:28)(cid:18).(cid:24).(cid:8)(cid:3) (cid:2)(cid:19)’(cid:13)(cid:25)!(cid:19)(cid:22)(cid:25)(cid:14)9(cid:19)’(cid:19)&! (cid:18)(cid:28)7 7:(cid:18) (cid:18)(cid:7); 7"’)(cid:13)(cid:21)(cid:14)(cid:22)%(cid:14)(cid:31)(cid:19)(cid:25)! 7 (cid:16)(cid:4) (cid:31)(cid:19)&(cid:20)(cid:23) (cid:13) (cid:4)(cid:29)?(cid:15)(cid:14)1(cid:3), : (cid:13)(cid:21)(cid:11)(cid:26)(cid:26)(cid:14)8(cid:13)(cid:19)(cid:12)(cid:23)& (cid:7) < < (cid:16)(cid:29)(cid:4)(cid:4) (cid:18)(cid:22)(cid:26)#(cid:13)#(cid:14)(cid:31)(cid:11)(cid:20)4(cid:11)(cid:12)(cid:13)(cid:14)(cid:24)(cid:23)(cid:19)(cid:20)4(cid:25)(cid:13)!! (cid:7)(cid:16) (cid:30)(cid:29)?(cid:15) (cid:30)(cid:29)(cid:17)(cid:15) (cid:30)(cid:29)>(cid:15) (cid:3)&(cid:11)(cid:25)#(cid:22)%%(cid:14) (cid:7)(cid:30) (cid:4)(cid:29)(cid:4)(cid:15) < < : (cid:13)(cid:21)(cid:11)(cid:26)(cid:26)(cid:14)=(cid:19)#&(cid:23) . (cid:17)(cid:29)(cid:5)(cid:4) (cid:17)(cid:29)>(cid:4) >(cid:29)(cid:16)(cid:4) (cid:18)(cid:22)(cid:26)#(cid:13)#(cid:14)(cid:31)(cid:11)(cid:20)4(cid:11)(cid:12)(cid:13)(cid:14)=(cid:19)#&(cid:23) .(cid:30) (cid:15)(cid:29)(cid:4)(cid:4) (cid:15)(cid:29)-(cid:4) (cid:15)(cid:29)?(cid:4) : (cid:13)(cid:21)(cid:11)(cid:26)(cid:26)(cid:14)9(cid:13)(cid:25)(cid:12)&(cid:23) (cid:2) ?(cid:29)(cid:6)(cid:4) (cid:17)(cid:29)(cid:16)(cid:4) (cid:17)(cid:29)(cid:15)(cid:4) 3(cid:22)(cid:22)&(cid:14)9(cid:13)(cid:25)(cid:12)&(cid:23) 9 (cid:4)(cid:29)(cid:15)(cid:15) (cid:4)(cid:29)(cid:17)(cid:15) (cid:4)(cid:29)(cid:6)(cid:15) 3(cid:22)(cid:22)&(cid:10)(cid:21)(cid:19)(cid:25)& 9(cid:30) (cid:30)(cid:29)(cid:16)(cid:15)(cid:14)(cid:8).3 9(cid:13)(cid:11)#(cid:14)(cid:24)(cid:23)(cid:19)(cid:20)4(cid:25)(cid:13)!! (cid:20) (cid:4)(cid:29)(cid:4)(cid:6) < (cid:4)(cid:29)(cid:16)(cid:15) 3(cid:22)(cid:22)&(cid:14)(cid:7)(cid:25)(cid:12)(cid:26)(cid:13) (cid:3) (cid:4)@ (cid:5)@ >@ 9(cid:13)(cid:11)#(cid:14)=(cid:19)#&(cid:23) ) (cid:4)(cid:29)(cid:16)(cid:16) < (cid:4)(cid:29)-> (cid:30)(cid:26)(cid:13)(cid:6)(cid:12)(cid:31) (cid:30)(cid:29) (cid:31)(cid:19)(cid:25)(cid:14)(cid:30)(cid:14) (cid:19)!"(cid:11)(cid:26)(cid:14)(cid:19)(cid:25)#(cid:13)$(cid:14)%(cid:13)(cid:11)&"(cid:21)(cid:13)(cid:14)’(cid:11)(cid:27)(cid:14) (cid:11)(cid:21)(cid:27)((cid:14))"&(cid:14)’"!&(cid:14))(cid:13)(cid:14)(cid:26)(cid:22)(cid:20)(cid:11)&(cid:13)#(cid:14)*(cid:19)&(cid:23)(cid:19)(cid:25)(cid:14)&(cid:23)(cid:13)(cid:14)(cid:23)(cid:11)&(cid:20)(cid:23)(cid:13)#(cid:14)(cid:11)(cid:21)(cid:13)(cid:11)(cid:29) (cid:16)(cid:29) (cid:2)(cid:19)’(cid:13)(cid:25)!(cid:19)(cid:22)(cid:25)!(cid:14)(cid:2)(cid:14)(cid:11)(cid:25)#(cid:14).(cid:30)(cid:14)#(cid:22)(cid:14)(cid:25)(cid:22)&(cid:14)(cid:19)(cid:25)(cid:20)(cid:26)"#(cid:13)(cid:14)’(cid:22)(cid:26)#(cid:14)%(cid:26)(cid:11)!(cid:23)(cid:14)(cid:22)(cid:21)(cid:14)(cid:10)(cid:21)(cid:22)&(cid:21)"!(cid:19)(cid:22)(cid:25)!(cid:29)(cid:14)(cid:18)(cid:22)(cid:26)#(cid:14)%(cid:26)(cid:11)!(cid:23)(cid:14)(cid:22)(cid:21)(cid:14)(cid:10)(cid:21)(cid:22)&(cid:21)"!(cid:19)(cid:22)(cid:25)!(cid:14)!(cid:23)(cid:11)(cid:26)(cid:26)(cid:14)(cid:25)(cid:22)&(cid:14)(cid:13)$(cid:20)(cid:13)(cid:13)#(cid:14)(cid:4)(cid:29)(cid:16)(cid:4)(cid:14)’’(cid:14)(cid:10)(cid:13)(cid:21)(cid:14)!(cid:19)#(cid:13)(cid:29) -(cid:29) (cid:2)(cid:19)’(cid:13)(cid:25)!(cid:19)(cid:22)(cid:25)(cid:19)(cid:25)(cid:12)(cid:14)(cid:11)(cid:25)#(cid:14)&(cid:22)(cid:26)(cid:13)(cid:21)(cid:11)(cid:25)(cid:20)(cid:19)(cid:25)(cid:12)(cid:14)(cid:10)(cid:13)(cid:21)(cid:14)(cid:7)(cid:3)(cid:18).(cid:14)0(cid:30)(cid:5)(cid:29)(cid:15)(cid:18)(cid:29) 1(cid:3),2 1(cid:11)!(cid:19)(cid:20)(cid:14)(cid:2)(cid:19)’(cid:13)(cid:25)!(cid:19)(cid:22)(cid:25)(cid:29)(cid:14)(cid:24)(cid:23)(cid:13)(cid:22)(cid:21)(cid:13)&(cid:19)(cid:20)(cid:11)(cid:26)(cid:26)(cid:27)(cid:14)(cid:13)$(cid:11)(cid:20)&(cid:14) (cid:11)(cid:26)"(cid:13)(cid:14)!(cid:23)(cid:22)*(cid:25)(cid:14)*(cid:19)&(cid:23)(cid:22)"&(cid:14)&(cid:22)(cid:26)(cid:13)(cid:21)(cid:11)(cid:25)(cid:20)(cid:13)!(cid:29) (cid:8).32 (cid:8)(cid:13)%(cid:13)(cid:21)(cid:13)(cid:25)(cid:20)(cid:13)(cid:14)(cid:2)(cid:19)’(cid:13)(cid:25)!(cid:19)(cid:22)(cid:25)((cid:14)"!"(cid:11)(cid:26)(cid:26)(cid:27)(cid:14)*(cid:19)&(cid:23)(cid:22)"&(cid:14)&(cid:22)(cid:26)(cid:13)(cid:21)(cid:11)(cid:25)(cid:20)(cid:13)((cid:14)%(cid:22)(cid:21)(cid:14)(cid:19)(cid:25)%(cid:22)(cid:21)’(cid:11)&(cid:19)(cid:22)(cid:25)(cid:14)(cid:10)"(cid:21)(cid:10)(cid:22)!(cid:13)!(cid:14)(cid:22)(cid:25)(cid:26)(cid:27)(cid:29) (cid:18)(cid:19)(cid:20)(cid:21)(cid:22)(cid:20)(cid:23)(cid:19)(cid:10)(cid:24)(cid:13)(cid:20)(cid:23)(cid:25)(cid:22)(cid:26)(cid:22)(cid:12)(cid:27)(cid:2)(cid:21)(cid:11)*(cid:19)(cid:25)(cid:12),(cid:4)(cid:5)(cid:9)(cid:4)(cid:17)(cid:16)1 DS30009995E-page 330  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 20-Lead Plastic Shrink Small Outline (SS) - 5.30 mm Body [SSOP] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging 0.65 0.45 SILK SCREEN c Y1 G X1 E RECOMMENDED LAND PATTERN Units MILLIMETERS Dimension Limits MIN NOM MAX Contact Pitch E 0.65 BSC Contact Pad Spacing C 7.20 Contact Pad Width (X20) X1 0.45 Contact Pad Length (X20) Y1 1.75 Distance Between Pads G 0.20 Notes: 1. Dimensioning and tolerancing per ASME Y14.5M BSC: Basic Dimension. Theoretically exact value shown without tolerances. Microchip Technology Drawing No. C04-2072B  2011-2017 Microchip Technology Inc. DS30009995E-page 331

PIC24FV32KA304 FAMILY (cid:2) (cid:4)(cid:5)(cid:6)(cid:7)(cid:8)(cid:9)(cid:10)(cid:11)(cid:7)(cid:12)(cid:13)(cid:14)(cid:15)(cid:9)!#$(cid:14)(cid:19)"(cid:9)!(cid:24)(cid:7)(cid:11)(cid:11)(cid:9)%(cid:17)(cid:13)(cid:11)(cid:14)(cid:19)(cid:6)(cid:9)(cid:20)!!(cid:21)(cid:9)(cid:22)(cid:9)&’(cid:23)(cid:3)(cid:9)(cid:24)(cid:24)(cid:9)(cid:25)(cid:26)(cid:8)(cid:27)(cid:9)(cid:28)!!%(cid:10)(cid:29) (cid:30)(cid:26)(cid:13)(cid:6)(cid:31) 3(cid:22)(cid:21)(cid:14)&(cid:23)(cid:13)(cid:14)’(cid:22)!&(cid:14)(cid:20)"(cid:21)(cid:21)(cid:13)(cid:25)&(cid:14)(cid:10)(cid:11)(cid:20)4(cid:11)(cid:12)(cid:13)(cid:14)#(cid:21)(cid:11)*(cid:19)(cid:25)(cid:12)!((cid:14)(cid:10)(cid:26)(cid:13)(cid:11)!(cid:13)(cid:14)!(cid:13)(cid:13)(cid:14)&(cid:23)(cid:13)(cid:14)(cid:18)(cid:19)(cid:20)(cid:21)(cid:22)(cid:20)(cid:23)(cid:19)(cid:10)(cid:14)(cid:31)(cid:11)(cid:20)4(cid:11)(cid:12)(cid:19)(cid:25)(cid:12)(cid:14)(cid:3)(cid:10)(cid:13)(cid:20)(cid:19)%(cid:19)(cid:20)(cid:11)&(cid:19)(cid:22)(cid:25)(cid:14)(cid:26)(cid:22)(cid:20)(cid:11)&(cid:13)#(cid:14)(cid:11)&(cid:14) (cid:23)&&(cid:10)255***(cid:29)’(cid:19)(cid:20)(cid:21)(cid:22)(cid:20)(cid:23)(cid:19)(cid:10)(cid:29)(cid:20)(cid:22)’5(cid:10)(cid:11)(cid:20)4(cid:11)(cid:12)(cid:19)(cid:25)(cid:12) D N E E1 1 2 b NOTE1 e c A A2 φ A1 L1 L 6(cid:25)(cid:19)&! (cid:18)(cid:28)99(cid:28)(cid:18).(cid:24).(cid:8)(cid:3) (cid:2)(cid:19)’(cid:13)(cid:25)!(cid:19)(cid:22)(cid:25)(cid:14)9(cid:19)’(cid:19)&! (cid:18)(cid:28)7 7:(cid:18) (cid:18)(cid:7); 7"’)(cid:13)(cid:21)(cid:14)(cid:22)%(cid:14)(cid:31)(cid:19)(cid:25)! 7 (cid:16)> (cid:31)(cid:19)&(cid:20)(cid:23) (cid:13) (cid:4)(cid:29)?(cid:15)(cid:14)1(cid:3), : (cid:13)(cid:21)(cid:11)(cid:26)(cid:26)(cid:14)8(cid:13)(cid:19)(cid:12)(cid:23)& (cid:7) < < (cid:16)(cid:29)(cid:4)(cid:4) (cid:18)(cid:22)(cid:26)#(cid:13)#(cid:14)(cid:31)(cid:11)(cid:20)4(cid:11)(cid:12)(cid:13)(cid:14)(cid:24)(cid:23)(cid:19)(cid:20)4(cid:25)(cid:13)!! (cid:7)(cid:16) (cid:30)(cid:29)?(cid:15) (cid:30)(cid:29)(cid:17)(cid:15) (cid:30)(cid:29)>(cid:15) (cid:3)&(cid:11)(cid:25)#(cid:22)%%(cid:14) (cid:7)(cid:30) (cid:4)(cid:29)(cid:4)(cid:15) < < : (cid:13)(cid:21)(cid:11)(cid:26)(cid:26)(cid:14)=(cid:19)#&(cid:23) . (cid:17)(cid:29)(cid:5)(cid:4) (cid:17)(cid:29)>(cid:4) >(cid:29)(cid:16)(cid:4) (cid:18)(cid:22)(cid:26)#(cid:13)#(cid:14)(cid:31)(cid:11)(cid:20)4(cid:11)(cid:12)(cid:13)(cid:14)=(cid:19)#&(cid:23) .(cid:30) (cid:15)(cid:29)(cid:4)(cid:4) (cid:15)(cid:29)-(cid:4) (cid:15)(cid:29)?(cid:4) : (cid:13)(cid:21)(cid:11)(cid:26)(cid:26)(cid:14)9(cid:13)(cid:25)(cid:12)&(cid:23) (cid:2) (cid:6)(cid:29)(cid:6)(cid:4) (cid:30)(cid:4)(cid:29)(cid:16)(cid:4) (cid:30)(cid:4)(cid:29)(cid:15)(cid:4) 3(cid:22)(cid:22)&(cid:14)9(cid:13)(cid:25)(cid:12)&(cid:23) 9 (cid:4)(cid:29)(cid:15)(cid:15) (cid:4)(cid:29)(cid:17)(cid:15) (cid:4)(cid:29)(cid:6)(cid:15) 3(cid:22)(cid:22)&(cid:10)(cid:21)(cid:19)(cid:25)& 9(cid:30) (cid:30)(cid:29)(cid:16)(cid:15)(cid:14)(cid:8).3 9(cid:13)(cid:11)#(cid:14)(cid:24)(cid:23)(cid:19)(cid:20)4(cid:25)(cid:13)!! (cid:20) (cid:4)(cid:29)(cid:4)(cid:6) < (cid:4)(cid:29)(cid:16)(cid:15) 3(cid:22)(cid:22)&(cid:14)(cid:7)(cid:25)(cid:12)(cid:26)(cid:13) (cid:3) (cid:4)@ (cid:5)@ >@ 9(cid:13)(cid:11)#(cid:14)=(cid:19)#&(cid:23) ) (cid:4)(cid:29)(cid:16)(cid:16) < (cid:4)(cid:29)-> (cid:30)(cid:26)(cid:13)(cid:6)(cid:12)(cid:31) (cid:30)(cid:29) (cid:31)(cid:19)(cid:25)(cid:14)(cid:30)(cid:14) (cid:19)!"(cid:11)(cid:26)(cid:14)(cid:19)(cid:25)#(cid:13)$(cid:14)%(cid:13)(cid:11)&"(cid:21)(cid:13)(cid:14)’(cid:11)(cid:27)(cid:14) (cid:11)(cid:21)(cid:27)((cid:14))"&(cid:14)’"!&(cid:14))(cid:13)(cid:14)(cid:26)(cid:22)(cid:20)(cid:11)&(cid:13)#(cid:14)*(cid:19)&(cid:23)(cid:19)(cid:25)(cid:14)&(cid:23)(cid:13)(cid:14)(cid:23)(cid:11)&(cid:20)(cid:23)(cid:13)#(cid:14)(cid:11)(cid:21)(cid:13)(cid:11)(cid:29) (cid:16)(cid:29) (cid:2)(cid:19)’(cid:13)(cid:25)!(cid:19)(cid:22)(cid:25)!(cid:14)(cid:2)(cid:14)(cid:11)(cid:25)#(cid:14).(cid:30)(cid:14)#(cid:22)(cid:14)(cid:25)(cid:22)&(cid:14)(cid:19)(cid:25)(cid:20)(cid:26)"#(cid:13)(cid:14)’(cid:22)(cid:26)#(cid:14)%(cid:26)(cid:11)!(cid:23)(cid:14)(cid:22)(cid:21)(cid:14)(cid:10)(cid:21)(cid:22)&(cid:21)"!(cid:19)(cid:22)(cid:25)!(cid:29)(cid:14)(cid:18)(cid:22)(cid:26)#(cid:14)%(cid:26)(cid:11)!(cid:23)(cid:14)(cid:22)(cid:21)(cid:14)(cid:10)(cid:21)(cid:22)&(cid:21)"!(cid:19)(cid:22)(cid:25)!(cid:14)!(cid:23)(cid:11)(cid:26)(cid:26)(cid:14)(cid:25)(cid:22)&(cid:14)(cid:13)$(cid:20)(cid:13)(cid:13)#(cid:14)(cid:4)(cid:29)(cid:16)(cid:4)(cid:14)’’(cid:14)(cid:10)(cid:13)(cid:21)(cid:14)!(cid:19)#(cid:13)(cid:29) -(cid:29) (cid:2)(cid:19)’(cid:13)(cid:25)!(cid:19)(cid:22)(cid:25)(cid:19)(cid:25)(cid:12)(cid:14)(cid:11)(cid:25)#(cid:14)&(cid:22)(cid:26)(cid:13)(cid:21)(cid:11)(cid:25)(cid:20)(cid:19)(cid:25)(cid:12)(cid:14)(cid:10)(cid:13)(cid:21)(cid:14)(cid:7)(cid:3)(cid:18).(cid:14)0(cid:30)(cid:5)(cid:29)(cid:15)(cid:18)(cid:29) 1(cid:3),2 1(cid:11)!(cid:19)(cid:20)(cid:14)(cid:2)(cid:19)’(cid:13)(cid:25)!(cid:19)(cid:22)(cid:25)(cid:29)(cid:14)(cid:24)(cid:23)(cid:13)(cid:22)(cid:21)(cid:13)&(cid:19)(cid:20)(cid:11)(cid:26)(cid:26)(cid:27)(cid:14)(cid:13)$(cid:11)(cid:20)&(cid:14) (cid:11)(cid:26)"(cid:13)(cid:14)!(cid:23)(cid:22)*(cid:25)(cid:14)*(cid:19)&(cid:23)(cid:22)"&(cid:14)&(cid:22)(cid:26)(cid:13)(cid:21)(cid:11)(cid:25)(cid:20)(cid:13)!(cid:29) (cid:8).32 (cid:8)(cid:13)%(cid:13)(cid:21)(cid:13)(cid:25)(cid:20)(cid:13)(cid:14)(cid:2)(cid:19)’(cid:13)(cid:25)!(cid:19)(cid:22)(cid:25)((cid:14)"!"(cid:11)(cid:26)(cid:26)(cid:27)(cid:14)*(cid:19)&(cid:23)(cid:22)"&(cid:14)&(cid:22)(cid:26)(cid:13)(cid:21)(cid:11)(cid:25)(cid:20)(cid:13)((cid:14)%(cid:22)(cid:21)(cid:14)(cid:19)(cid:25)%(cid:22)(cid:21)’(cid:11)&(cid:19)(cid:22)(cid:25)(cid:14)(cid:10)"(cid:21)(cid:10)(cid:22)!(cid:13)!(cid:14)(cid:22)(cid:25)(cid:26)(cid:27)(cid:29) (cid:18)(cid:19)(cid:20)(cid:21)(cid:22)(cid:20)(cid:23)(cid:19)(cid:10)(cid:24)(cid:13)(cid:20)(cid:23)(cid:25)(cid:22)(cid:26)(cid:22)(cid:12)(cid:27)(cid:2)(cid:21)(cid:11)*(cid:19)(cid:25)(cid:12),(cid:4)(cid:5)(cid:9)(cid:4)(cid:17)-1 DS30009995E-page 332  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging  2011-2017 Microchip Technology Inc. DS30009995E-page 333

PIC24FV32KA304 FAMILY Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging DS30009995E-page 334  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging  2011-2017 Microchip Technology Inc. DS30009995E-page 335

PIC24FV32KA304 FAMILY Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging DS30009995E-page 336  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging  2011-2017 Microchip Technology Inc. DS30009995E-page 337

PIC24FV32KA304 FAMILY Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging DS30009995E-page 338  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging  2011-2017 Microchip Technology Inc. DS30009995E-page 339

PIC24FV32KA304 FAMILY DS30009995E-page 340  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY  2011-2017 Microchip Technology Inc. DS30009995E-page 341

PIC24FV32KA304 FAMILY (cid:2) (cid:4)(cid:5)(cid:6)(cid:7)(cid:8)(cid:9)(cid:10)(cid:11)(cid:7)(cid:12)(cid:13)(cid:14)(cid:15)(cid:9)((cid:17)(cid:7)(cid:8)(cid:9))(cid:11)(cid:7)(cid:13)*(cid:9)(cid:30)(cid:26)(cid:9)(cid:5)(cid:6)(cid:7)(cid:8)(cid:9)(cid:10)(cid:7)(cid:15)"(cid:7)+(cid:6)(cid:9)(cid:20),(cid:5)(cid:21)(cid:9)(cid:22)(cid:9)-.-(cid:9)(cid:24)(cid:24)(cid:9)(cid:25)(cid:26)(cid:8)(cid:27)(cid:9)(cid:28)()(cid:30)(cid:29) /(cid:14)(cid:13)#(cid:9)(cid:3)’&&(cid:9)(cid:24)(cid:24)(cid:9)0(cid:26)(cid:19)(cid:13)(cid:7)(cid:15)(cid:13)(cid:9)(cid:5)(cid:6)(cid:19)+(cid:13)# (cid:30)(cid:26)(cid:13)(cid:6)(cid:31) 3(cid:22)(cid:21)(cid:14)&(cid:23)(cid:13)(cid:14)’(cid:22)!&(cid:14)(cid:20)"(cid:21)(cid:21)(cid:13)(cid:25)&(cid:14)(cid:10)(cid:11)(cid:20)4(cid:11)(cid:12)(cid:13)(cid:14)#(cid:21)(cid:11)*(cid:19)(cid:25)(cid:12)!((cid:14)(cid:10)(cid:26)(cid:13)(cid:11)!(cid:13)(cid:14)!(cid:13)(cid:13)(cid:14)&(cid:23)(cid:13)(cid:14)(cid:18)(cid:19)(cid:20)(cid:21)(cid:22)(cid:20)(cid:23)(cid:19)(cid:10)(cid:14)(cid:31)(cid:11)(cid:20)4(cid:11)(cid:12)(cid:19)(cid:25)(cid:12)(cid:14)(cid:3)(cid:10)(cid:13)(cid:20)(cid:19)%(cid:19)(cid:20)(cid:11)&(cid:19)(cid:22)(cid:25)(cid:14)(cid:26)(cid:22)(cid:20)(cid:11)&(cid:13)#(cid:14)(cid:11)&(cid:14) (cid:23)&&(cid:10)255***(cid:29)’(cid:19)(cid:20)(cid:21)(cid:22)(cid:20)(cid:23)(cid:19)(cid:10)(cid:29)(cid:20)(cid:22)’5(cid:10)(cid:11)(cid:20)4(cid:11)(cid:12)(cid:19)(cid:25)(cid:12) DS30009995E-page 342  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 44-Lead Plastic Quad Flat, No Lead Package (ML) - 8x8 mm Body [QFN or VQFN] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging D A B N NOTE 1 1 2 E (DATUM B) (DATUM A) 2X 0.20 C 2X 0.20 C TOP VIEW A1 0.10 C C SEATING A PLANE 44X A3 0.08 C SIDE VIEW L 0.10 C A B D2 0.10 C A B E2 K 2 1 NOTE 1 N 44X b e 0.07 C A B 0.05 C BOTTOM VIEW Microchip Technology Drawing C04-103D Sheet 1 of 2  2011-2017 Microchip Technology Inc. DS30009995E-page 343

PIC24FV32KA304 FAMILY 44-Lead Plastic Quad Flat, No Lead Package (ML) - 8x8 mm Body [QFN or VQFN] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging Units MILLIMETERS Dimension Limits MIN NOM MAX Number of Pins N 44 Pitch e 0.65 BSC Overall Height A 0.80 0.90 1.00 Standoff A1 0.00 0.02 0.05 Terminal Thickness A3 0.20 REF Overall Width E 8.00 BSC Exposed Pad Width E2 6.25 6.45 6.60 Overall Length D 8.00 BSC Exposed Pad Length D2 6.25 6.45 6.60 Terminal Width b 0.20 0.30 0.35 Terminal Length L 0.30 0.40 0.50 Terminal-to-Exposed-Pad K 0.20 - - Notes: 1. Pin 1 visual index feature may vary, but must be located within the hatched area. 2. Package is saw singulated 3. Dimensioning and tolerancing per ASME Y14.5M BSC: Basic Dimension. Theoretically exact value shown without tolerances. REF: Reference Dimension, usually without tolerance, for information purposes only. Microchip Technology Drawing C04-103D Sheet 2 of 2 DS30009995E-page 344  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 44-Lead Plastic Quad Flat, No Lead Package (ML) - 8x8 mm Body [QFN or VQFN] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging C1 X2 EV 44 G2 1 2 ØV EV C2 Y2 G1 Y1 E SILK SCREEN X1 RECOMMENDED LAND PATTERN Units MILLIMETERS Dimension Limits MIN NOM MAX Contact Pitch E 0.65 BSC Optional Center Pad Width X2 6.60 Optional Center Pad Length Y2 6.60 Contact Pad Spacing C1 8.00 Contact Pad Spacing C2 8.00 Contact Pad Width (X44) X1 0.35 Contact Pad Length (X44) Y1 0.85 Contact Pad to Contact Pad (X40) G1 0.30 Contact Pad to Center Pad (X44) G2 0.28 Thermal Via Diameter V 0.33 Thermal Via Pitch EV 1.20 Notes: 1. Dimensioning and tolerancing per ASME Y14.5M BSC: Basic Dimension. Theoretically exact value shown without tolerances. 2. For best soldering results, thermal vias, if used, should be filled or tented to avoid solder loss during reflow process Microchip Technology Drawing No. C04-2103C  2011-2017 Microchip Technology Inc. DS30009995E-page 345

PIC24FV32KA304 FAMILY 44-Lead Plastic Thin Quad Flatpack (PT) - 10x10x1.0 mm Body [TQFP] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging D A D1 B NOTE 2 (DATUM A) (DATUM B) E1 E A A NOTE 1 2X N 0.20 H A B 2X 1 2 3 0.20 H A B TOP VIEW 4X 11 TIPS 0.20 C A B A A2 C SEATING PLANE 0.10 C A1 SIDE VIEW 1 2 3 N NOTE 1 44 X b 0.20 C A B e BOTTOM VIEW Microchip Technology Drawing C04-076C Sheet 1 of 2 DS30009995E-page 346  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY 44-Lead Plastic Thin Quad Flatpack (PT) - 10x10x1.0 mm Body [TQFP] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging H c θ L (L1) SECTION A-A Units MILLIMETERS Dimension Limits MIN NOM MAX Number of Leads N 44 Lead Pitch e 0.80 BSC Overall Height A - - 1.20 Standoff A1 0.05 - 0.15 Molded Package Thickness A2 0.95 1.00 1.05 Overall Width E 12.00 BSC Molded Package Width E1 10.00 BSC Overall Length D 12.00 BSC Molded Package Length D1 10.00 BSC Lead Width b 0.30 0.37 0.45 Lead Thickness c 0.09 - 0.20 Lead Length L 0.45 0.60 0.75 Footprint L1 1.00 REF Foot Angle θ 0° 3.5° 7° Notes: 1. Pin 1 visual index feature may vary, but must be located within the hatched area. 2. Exact shape of each corner is optional. 3. Dimensioning and tolerancing per ASME Y14.5M BSC: Basic Dimension. Theoretically exact value shown without tolerances. REF: Reference Dimension, usually without tolerance, for information purposes only. Microchip Technology Drawing C04-076C Sheet 2 of 2  2011-2017 Microchip Technology Inc. DS30009995E-page 347

PIC24FV32KA304 FAMILY 44-Lead Plastic Thin Quad Flatpack (PT) - 10X10X1 mm Body, 2.00 mm Footprint [TQFP] Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging C1 44 1 2 G C2 Y1 X1 E SILK SCREEN RECOMMENDED LAND PATTERN Units MILLIMETERS Dimension Limits MIN NOM MAX Contact Pitch E 0.80 BSC Contact Pad Spacing C1 11.40 Contact Pad Spacing C2 11.40 Contact Pad Width (X44) X1 0.55 Contact Pad Length (X44) Y1 1.50 Distance Between Pads G 0.25 Notes: 1. Dimensioning and tolerancing per ASME Y14.5M BSC: Basic Dimension. Theoretically exact value shown without tolerances. Microchip Technology Drawing No. C04-2076B DS30009995E-page 348  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging  2011-2017 Microchip Technology Inc. DS30009995E-page 349

PIC24FV32KA304 FAMILY Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging DS30009995E-page 350  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY  2011-2017 Microchip Technology Inc. DS30009995E-page 351

PIC24FV32KA304 FAMILY NOTES: DS30009995E-page 352  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY APPENDIX A: REVISION HISTORY Added the following timing diagrams and timing requirement tables to Section29.0 “Electrical Characteristics”: Revision A (March 2011) • Figure29-6 (Reset, Watchdog Timer, Oscillator Original data sheet for the PIC24FV32KA304 family of Start-up Timer and Power-up Timer Timing devices. Characteristics) • Figure29-7 (Brown-out Reset Characteristics) Revision B (April 2011) • Figure29-9 (Input Capture x Timings) through Section25.0 “Charge Time Measurement Unit Figure29-21 (SPIx Module Slave Mode Timing (CTMU)” was revised to change the description of the Characteristics (CKE = 1)) IRNGx bits in CTMUICON (Register25-3). Setting ‘01’ • Table29-28 (Input Capture x Requirements) is the base current level (0.55 A nominal) and setting through Table29-39 (SPIx Module Slave Mode ‘00’ is 1000x base current. Timing Requirements (CKE = 1)) Section29.0 “Electrical Characteristics” was revised • Figure29-22 (A/D Conversion Timing) to change the following typical IPD specifications: Updated Table29-5 to add specification, DC15. • DC20h/i/j/k from 204 A to 200 A Replaced Table29-6, Table29-7 and Table29-8 with • DC60h/i/j/k from 0.15 A to 0.025 A new, shorter versions that remove unimplemented tem- • DC60l/m/n/o from 0.25 A to 0.040 A perature options. (No existing specification values have been changed in this process.) • DC72h/i/j/k from 0.80 A to 0.70 A Updated Table29-16 with correct values for Revision C (April 2012) CTMUICON bit settings. Combined previous Table29-21 and Table29-22 to Updated the Pin Diagrams on Pages 3 through 7, to create a new Table29-21 (AC Characteristics: Internal change “LVDIN” to “HLVDIN” in all occurrences, and RC Accuracy). All existing subsequent tables are correct the placement of certain functions. renumbered accordingly. Updated Table1-3 to remove references to unimple- Updated Table29-26 to add specifications, SY35 and mented package types, corrected several erroneous SY55. pin assignments and removed other alternate but unimplemented assignments. Updated Table29-40: For Section5.0 “Flash Program Memory”, updated • Split AD01 into separate entries for “F” and “FV” Example5-2, Example5-3 and Example5-4 with new device families table offset functions. • Added specifications, AD08 (IVREF) and AD09 Updated Figure12-1 to correctly show the (ZVREF) implemented Timer1 input options. • Changed AD17 (2.5k max. to 1k max.) For Section22.0 “12-Bit A/D Converter with Updated Table29-41: Threshold Detect”: • Changed AD50 (75 ns min. to 600 ns min.) • Updated Register22-1 to add the MODE12 bit • Changed AD51 (250 ns typ. to 1.67 µs typ.) • Updated the descriptions of the PVCFGx and • Changed AD60 (0.5 TAD min. to 2 TAD min.) CSCNA bits in Register22-2 • Split AD55 into separate entries for 10-bit and • Updated Register22-4 to change the VRSREQ 12-bit conversions bit to a reserved bit position Added Section30.0 “DC and AC Characteristics • Modified footnote text in Register22-5 Graphs and Tables”, with Figure30-1 through • Corrected CHOLD in Figure22-2 Figure30-39. For Section25.0 “Charge Time Measurement Unit Replaced some of the packaging diagrams in (CTMU)”: Section31.0 “Packaging Information” with the newly revised diagrams. • Updated the text in Section25.1 “Measuring Capacitance” and Section25.3 “Pulse Genera- Other minor typographic corrections throughout. tion and Delay” to better reflect the module’s implementation • Updated Figure25-3 to show additional detail in pulse generation  2011-2017 Microchip Technology Inc. DS30009995E-page 353

PIC24FV32KA304 FAMILY Revision D (March 2013) For Section29.0 “Electrical Characteristics”: • Updated captioning on all specification tables to Throughout the data sheet: corrected the name of include extended temperature data RCON register bit 12 as RETEN, to maintain consis- tency with other PIC24F devices (was previously • Amended Table29-8 to include +125°C data for LVREN). In addition, changed the description of the bit all existing specifications in the RCON register (Register7-1) to clarify its • Added new Table29-27 and Figure29-8 to char- function in controlling the Retention Regulator. acterize external clock input specifications for general purpose timers (all subsequent tables and Throughout the data sheet: corrected the name of figures are renumbered accordingly) FPOR Configuration register bit 2 as RETCFG, to maintain consistency with other PIC24F devices (was • Added parameter numbers to several existing but previously LVRCFG). In addition, changed the descrip- previous unnumbered parameters in multiple tion of the bit in the FPOR Configuration register tables (Register26-6) to clarify its function in enabling the Updated Section30.0 “DC and AC Characteristics Retention Regulator. Graphs and Tables”: For Section10.4 “Voltage Regulator-Based • Added additional graphs for Extended tempera- Power-Saving Features”: ture devices (Section30.2 “Characteristics for • Removed all references to Fast Wake-up Sleep Extended Temperature Devices (-40°C to mode, not implemented in this device +125°C)”, Figure30-40 through Figure30-56) • Changed all references of the High-Voltage • Replaced Figure30-32 with an updated graph Regulator to On-Chip Voltage Regulator Replaced some of the packaging diagrams in • Removed all references to the Low-Voltage Section31.0 “Packaging Information” with the Regulator, which was replaced in most cases with newly revised diagrams. Retention Regulator Updates Product Information System to include • Clarified the Retention Regulator’s operation in extended temperature devices in the information key. Section10.4.3 “Retention Sleep Mode” Other minor typographic corrections throughout. (formerly “Low-Voltage Sleep Mode”) • Modified Table10-1 for consistency with the Revision E (October 2017) above changes Corrects Section26.2 “On-Chip Voltage Regulator” Changed the PGEC2/PGED2 44-Pin value to 9 in to clarify the operation of the on-chip regulator in “F” Table1-3. and “FV” families, and include DC parameters and Removed the OFFCAL bit from Table4-16 and specifications. Register22-2. Updated Register6-1 to include the correct Programming Operations for NVMP<5:0>. Updated Figure22-1. Updated footnotes in Register25-2. Updated ambient temperature under bias range in Section29.0 “Electrical Characteristics”, updated the DC16 electrical specs in Table29-21, updated the F20 FRC electrical specs in Table29-3 and changed the Minimum Input Capture x requirement for IC15 TccP. Other minor typographic and formatting corrections throughout. DS30009995E-page 354  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY INDEX A CTMU Typical Connections and Internal Configuration for Pulse Delay Generation .......233 A/D CTMU Typical Connections and Internal Buffer Data Formats .................................................222 Configuration for Time Measurement ..............232 Control Registers .....................................................210 Data Access from Program Space AD1CHITH/L ....................................................210 Address Generation ...........................................52 AD1CHS ..........................................................210 Data EEPROM Addressing with TBLPAG and AD1CON1 ........................................................210 NVM Registers ..................................................65 AD1CON2 ........................................................210 High/Low-Voltage Detect (HLVD) ............................205 AD1CON3 ........................................................210 I2C Module ...............................................................170 AD1CON5 ........................................................210 Individual Comparator Configurations .....................226 AD1CSSH/L .....................................................210 Input Capture x ........................................................147 AD1CTMUENH/L .............................................210 MCLR Pin Connections .............................................24 Result Buffers ..........................................................210 On-Chip Regulator Connections ..............................248 Sampling Requirements ...........................................220 Output Compare x (16-Bit Mode) ............................152 Transfer Function .....................................................221 Output Compare x (Double-Buffered, AC Characteristics 16-Bit PWM Mode) ..........................................154 A/D Conversion ........................................................294 PIC24F CPU Core .....................................................30 A/D Module Specifications .......................................293 PIC24FV32KA304 Family (General) .........................15 Capacitive Loading Requirements on PSV Operation ...........................................................55 Output Pins ......................................................276 Recommended Minimum Connections ......................23 CLKO and I/O ..........................................................279 Reset System ............................................................69 Comparator ..............................................................280 RTCC Module ..........................................................185 Comparator Voltage Reference Settling Time .........280 Serial Resistor .........................................................131 External Clock ..........................................................277 I2C Bus Data (Master Mode) ............................284, 285 Shared I/O Port Structure ........................................135 I2C Bus Data (Slave Mode) ......................................286 Simplified UARTx ....................................................177 I2C Bus Start/Stop Bits (Slave Mode) ......................287 SPI1 Module (Enhanced Buffer Mode) ....................163 SPI1 Module (Standard Buffer Mode) .....................162 Internal RC Accuracy ...............................................278 System Clock ...........................................................115 Internal RC Oscillator Specifications ........................278 Table Register Addressing ........................................57 Load Conditions and Requirements .........................276 Timer2/3, Timer4/5 (32-Bit) .....................................142 PLL Clock Specifications .........................................278 Watchdog Timer (WDT) ...........................................249 Reset, Watchdog Timer. Oscillator Start-up Timer, Power-up Timer, Brown-out C Reset Requirements ........................................281 C Compilers SPIx Master Mode (CKE = 0) ..................................289 MPLAB XC Compilers .............................................252 SPIx Master Mode (CKE = 1) ..................................290 Charge Time Measurement Unit. See CTMU. SPIx Slave Mode (CKE = 0) ....................................291 Code Examples SPIx Slave Mode (CKE = 1) ....................................292 Basic Sequence for Clock Switching .......................122 Temperature and Voltage Specifications .................276 Data EEPROM Bulk Erase ........................................67 UARTx .....................................................................288 Data EEPROM Unlock Sequence .............................63 Assembler Erasing a Program Memory Row, ‘C’ Language .......61 MPASM Assembler ..................................................252 Erasing a Program Memory Row, B Assembly Language ..........................................60 I/O Port Write/Read .................................................138 Baud Rate Generator Initiating a Programming Sequence, Setting as a Bus Master ...........................................171 ‘C’ Language .....................................................62 Block Diagrams Initiating a Programming Sequence, 12-Bit A/D Converter ................................................208 Assembly Language ..........................................62 12-Bit A/D Converter Analog Input Model ................220 Loading the Write Buffers, ‘C’ Language ...................62 16-Bit Asynchronous Timer3 and Timer5 ................143 Loading the Write Buffers, Assembly Language .......61 16-Bit Synchronous Timer2 and Timer4 ..................143 PWRSAV Instruction Syntax ....................................125 16-Bit Timer1 ...........................................................139 Reading the Data EEPROM Using the Accessing Program Memory with TBLRD Command ..............................................68 Table Instructions ..............................................54 Setting the RTCWREN Bit .......................................186 CALL Stack Frame ....................................................51 Single-Word Erase ....................................................66 Comparator Voltage Reference ...............................229 Single-Word Write to Data EEPROM ........................67 Comparator x Module ..............................................225 Ultra Low-Power Wake-up Initialization ...................131 CPU Programmer’s Model .........................................31 Unlock Sequence ....................................................126 CRC Module ............................................................199 Code Protection ...............................................................250 CRC Shift Engine .....................................................199 Comparator ......................................................................225 CTMU Connections and Internal Configuration for Comparator Voltage Reference .......................................229 Capacitance Measurement ..............................232 Configuring ..............................................................229  2011-2017 Microchip Technology Inc. DS30009995E-page 355

PIC24FV32KA304 FAMILY Configuration Bits .............................................................239 Demo/Development Boards, Evaluation and Core Features ....................................................................11 Starter Kits ...............................................................254 CPU Development Support ......................................................251 ALU ............................................................................33 Third-Party Tools .....................................................254 Control Registers .......................................................32 E Core Registers ...........................................................30 Programmer’s Model ..................................................29 Electrical Characteristics CRC Absolute Maximum Ratings .....................................263 Control Registers .....................................................201 Thermal Operating Conditions .................................265 Typical Operation .....................................................201 Thermal Packaging ..................................................265 User Interface ..........................................................200 V/F Graphs ..............................................................264 Data .................................................................200 Equations Data Shift Direction ..........................................201 A/D Conversion Clock Period ..................................220 Interrupt Operation ...........................................201 Baud Rate Reload Calculation .................................171 Polynomial .......................................................200 Calculating the PWM Period ....................................155 CRC .................................................................................199 Calculation for Maximum PWM Resolution .............155 CTMU Device and SPIx Clock Speed Relationship ............168 Measuring Capacitance ...........................................231 PWM Period and Duty Cycle Calculations ...............155 Measuring Time .......................................................232 UARTx Baud Rate with BRGH = 0 ..........................178 Pulse Generation and Delay ....................................233 UARTx Baud Rate with BRGH = 1 ..........................178 Customer Change Notification Service ............................360 Errata ...................................................................................9 Customer Notification Service ..........................................360 Examples Customer Support ............................................................360 Baud Rate Error Calculation (BRGH = 0) ................178 Cyclic Redundancy Check. See CRC. F D Flash Program Memory Data EEPROM Memory .....................................................63 Control Registers .......................................................58 Erasing .......................................................................66 Enhanced ICSP Operation ........................................58 Operations .................................................................65 Programming Algorithm .............................................60 Programming Programming Operations ...........................................58 Bulk Erase ..........................................................67 RTSP Operation ........................................................58 Reading Data EEPROM ....................................68 Table Instructions ......................................................57 Single-Word Write ..............................................67 G Programming Control Registers NVMADR(U) ......................................................65 Guidelines for Getting Started ...........................................23 NVMCON ...........................................................63 External Oscillator Pins ..............................................27 NVMKEY ............................................................63 ICSP Pins ..................................................................26 Data Memory Master Clear (MCLR) Pin ..........................................24 Address Space ...........................................................37 Power Supply Pins .....................................................24 Memory Map ..............................................................37 Unused I/Os ...............................................................27 Near Data Space .......................................................38 Voltage Regulator Pin (VCAP) ....................................25 Organization ...............................................................38 H SFR Space .................................................................38 High/Low-Voltage Detect (HLVD) ....................................205 Software Stack ...........................................................51 High/Low-Voltage Detect. See HLVD. Space Width ...............................................................37 DC and AC Characteristics I Graphs and Tables I/O Ports Extended Temperature ....................................315 Analog Port Pins Configuration ................................136 Industrial Temperature .....................................295 Analog Selection Registers ......................................136 DC Characteristics Input Change Notification ........................................138 BOR Trip Points .......................................................266 Open-Drain Configuration ........................................136 Comparator Specifications .......................................274 Parallel (PIO) ...........................................................135 Comparator Voltage Reference ...............................274 I2C CTMU Current Source .............................................275 Clock Rates .............................................................171 Data EEPROM Memory ...........................................274 Communicating as Master in Single High/Low-Voltage Detect .........................................266 Master Environment ........................................169 I/O Pin Input Specifications ......................................272 Pin Remapping Options ...........................................169 I/O Pin Output Specifications ...................................273 Reserved Addresses ...............................................171 Idle Current (IIDLE) ...................................................268 Slave Address Masking ...........................................171 Internal Voltage Regulator .......................................275 In-Circuit Debugger ..........................................................250 Operating Current (IDD) ............................................267 In-Circuit Serial Programming (ICSP) ..............................250 Power-Down Current (IPD) .......................................269 Program Memory .....................................................273 Temperature and Voltage Specifications .................265 DS30009995E-page 356  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY Input Capture Power-Saving Features ...................................................125 Cascaded (32-Bit) Mode ..........................................148 Clock Frequency, Clock Switching ..........................125 Operations ...............................................................148 Coincident Interrupts ...............................................126 Synchronous, Trigger Modes ...................................147 Instruction-Based Modes .........................................125 Input Capture with Dedicated Timers ...............................147 Deep Sleep ......................................................126 Instruction Set Idle ...................................................................126 Opcode Symbols ......................................................256 Sleep ...............................................................125 Overview ..................................................................257 Selective Peripheral Control ....................................134 Summary ..................................................................255 Ultra Low-Power Wake-up .......................................131 Internet Address ...............................................................360 Voltage, Regulator-Based .......................................133 Interrupts Deep Sleep Mode ............................................133 Alternate Interrupt Vector Table (AIVT) .....................75 Retention Sleep Mode .....................................133 Control and Status Registers .....................................78 Run Mode ........................................................133 Implemented Vectors .................................................77 Sleep (Standby) Mode .....................................133 Interrupt Vector Table (IVT) .......................................75 Product Identification System ..........................................362 Reset Sequence ........................................................75 Program and Data Memory Setup Procedures ....................................................113 Access Using Table Instructions ...............................53 Trap Vectors ..............................................................77 Addressing Space .....................................................51 Vector Table ...............................................................76 Interfacing Spaces .....................................................51 Program Space Visibility ............................................55 M Program Memory Microchip Internet Web Site .............................................360 Address Space ..........................................................35 MPLAB Assembler, Linker, Librarian ...............................252 Data EEPROM ..........................................................36 MPLAB ICD 3 In-Circuit Debugger ..................................253 Device Configuration Words ......................................36 MPLAB PM3 Device Programmer ...................................253 Hard Memory Vectors ................................................36 MPLAB REAL ICE In-Circuit Emulator System ................253 Memory Map ..............................................................35 MPLAB X Integrated Development Organization ..............................................................36 Environment Software ..............................................251 Program Verification ........................................................250 MPLAB X SIM Software Simulator ...................................253 Pulse-Width Modulation (PWM) Mode .............................154 MPLIB Object Librarian ....................................................252 Pulse-Width Modulation. See PWM. MPLINK Object Linker .....................................................252 PWM Duty Cycle and Period .............................................155 N R Near Data Space ...............................................................38 Real-Time Clock and Calendar. See RTCC. O Register Maps On-Chip Voltage Regulator ..............................................248 A/D Converter ............................................................47 Oscillator Configuration Analog Select ............................................................48 Clock Switching ........................................................121 Clock Control .............................................................49 Enabling ...........................................................121 CPU Core ..................................................................39 Sequence .........................................................121 CRC ...........................................................................49 Configuration Bit Values for Clock Selection ...........116 CTMU ........................................................................48 Control Registers .....................................................117 Deep Sleep ................................................................49 CPU Clocking Scheme ............................................116 I2Cx ...........................................................................44 Initial Configuration on POR ....................................116 ICN ............................................................................40 Reference Clock Output ...........................................122 Input Capture .............................................................42 Output Compare Interrupt Controller .....................................................41 Cascaded (32-Bit) Mode ..........................................151 NVM ...........................................................................50 Operations ...............................................................153 Output Compare ........................................................43 Subcycle Resolution ................................................156 Pad Configuration ......................................................46 Synchronous, Trigger Modes ...................................151 PMD ...........................................................................50 Output Compare with Dedicated Timers ..........................151 PORTA ......................................................................45 P PORTB ......................................................................45 PORTC ......................................................................46 Packaging Real-Time Clock and Calendar (RTCC) ....................48 Details ......................................................................328 SPIx ...........................................................................45 Marking ....................................................................325 Timer .........................................................................42 PIC24F32KA304 Family Device Features (Summary) .......14 Triple Comparator ......................................................48 PIC24FV32KA304 Family Device Features UARTx .......................................................................44 (Summary) .................................................................13 Ultra Low-Power Wake-up .........................................50 PICkit 3 In-Circuit Debugger/Programmer .......................253 Pinout Descriptions ............................................................16 Power-Saving ...................................................................134  2011-2017 Microchip Technology Inc. DS30009995E-page 357

PIC24FV32KA304 FAMILY Registers IFS1 (Interrupt Flag Status 1) ....................................85 AD1CHITH (A/D Scan Compare Hit, IFS2 (Interrupt Flag Status 2) ....................................86 High Word) .......................................................217 IFS3 (Interrupt Flag Status 3) ....................................87 AD1CHITH (A/D Scan Compare Hit, IFS4 (Interrupt Flag Status 4) ....................................88 Low Word) ........................................................217 IFS5 (Interrupt Flag Status 5) ....................................89 AD1CHS (A/D Sample Select) .................................216 INTCON1 (Interrupt Control 1) ...................................81 AD1CON1 (A/D Control 1) .......................................211 INTCON2 (Interrupt Control 2) ...................................82 AD1CON2 (A/D Control 2) .......................................212 INTTREG (Interrupt Control and Status) .................112 AD1CON3 (A/D Control 3) .......................................214 IPC0 (Interrupt Priority Control 0) ..............................97 AD1CON5 (A/D Control 5) .......................................215 IPC1 (Interrupt Priority Control 1) ..............................98 AD1CSSH (A/D Input Scan Select, High Word) ......218 IPC12 (Interrupt Priority Control 12) ........................107 AD1CSSL (A/D Input Scan Select, Low Word) ........218 IPC15 (Interrupt Priority Control 15) ........................108 AD1CTMUENH (A/D CTMU Enable, IPC16 (Interrupt Priority Control 16) ........................109 High Word) .......................................................219 IPC18 (Interrupt Priority Control 18) ........................110 AD1CTMUENL (A/D CTMU Enable, IPC19 (Interrupt Priority Control 19) ........................110 Low Word) ........................................................219 IPC2 (Interrupt Priority Control 2) ..............................99 ALCFGRPT (Alarm Configuration) ...........................190 IPC20 (Interrupt Priority Control 20) ........................111 ALMINSEC (Alarm Minutes and IPC3 (Interrupt Priority Control 3) ............................100 Seconds Value) ................................................194 IPC4 (Interrupt Priority Control 4) ............................101 ALMTHDY (Alarm Month and Day Value) ...............193 IPC5 (Interrupt Priority Control 5) ............................102 ALWDHR (Alarm Weekday and Hours Value) .........193 IPC6 (Interrupt Priority Control 6) ............................103 ANSA (Analog Selection, PORTA) ..........................136 IPC7 (Interrupt Priority Control 7) ............................104 ANSB (Analog Selection, PORTB) ..........................137 IPC8 (Interrupt Priority Control 8) ............................105 ANSC (Analog Selection, PORTC) ..........................137 IPC9 (Interrupt Priority Control 9) ............................106 CLKDIV (Clock Divider) ...........................................119 MINSEC (RTCC Minutes and Seconds Value) ........192 CMSTAT (Comparator x Status) ..............................228 MTHDY (RTCC Month and Day Value) ...................191 CMxCON (Comparator x Control) ............................227 NVMCON (Nonvolatile Memory Control) ...................64 CORCON (CPU Control) ...........................................33 NVMCON (NVM Flash Memory Control) ...................59 CORCON (CPU Core Control) ...................................80 OCxCON1 (Output Compare x Control 1) ...............157 CRCCON1 (CRC Control 1) ....................................202 OCxCON2 (Output Compare x Control 2) ...............159 CRCCON2 (CRC Control 2) ....................................203 OSCCON (Oscillator Control) ..................................117 CRCXORH (CRC XOR Polynomial, High Byte) .......204 OSCTUN (FRC Oscillator Tune) ..............................120 CRCXORL (CRC XOR Polynomial, Low Byte) ........204 PADCFG1 (Pad Configuration Control) ...................176 CTMUCON1 (CTMU Control 1) ...............................234 RCFGCAL (RTCC Calibration CTMUCON2 (CTMU Control 2) ...............................235 and Configuration) ...........................................187 CTMUICON (CTMU Current Control) ......................237 RCON (Reset Control) ...............................................70 CVRCON (Comparator Voltage REFOCON (Reference Oscillator Control) ..............123 Reference Control) ...........................................230 RTCCSWT (RTCC Control/ DEVID (Device ID) ...................................................246 Sample Window Timer) ...................................195 DEVREV (Device Revision) .....................................247 RTCPWC (RTCC Configuration 2) ..........................189 DSCON (Deep Sleep Control) .................................129 SPIxCON1 (SPIx Control 1) .....................................166 DSWAKE (Deep Sleep Wake-up Source) ...............130 SPIxCON2 (SPIx Control 2) .....................................167 FBS (Boot Segment Configuration) .........................239 SPIxSTAT (SPIx Status and Control) ......................164 FDS (Deep Sleep Configuration) .............................245 SR (ALU STATUS) ..............................................32, 79 FGS (General Segment Configuration) ....................240 T1CON (Timer1 Control) .........................................140 FICD (In-Circuit Debugger Configuration) ................244 TxCON (Timer2/4 Control) .......................................144 FOSC (Oscillator Configuration) ..............................241 TyCON (Timer3/5 Control) .......................................145 FOSCSEL (Oscillator Selection Configuration) ........240 ULPWCON (ULPWU Control) .................................132 FPOR (Reset Configuration) ....................................243 UxMODE (UARTx Mode) .........................................180 FWDT (Watchdog Timer Configuration) ..................242 UxRXREG (UARTx Receive) ...................................184 HLVDCON (High/Low-Voltage Detect Control) ........206 UxSTA (UARTx Status and Control) ........................182 I2CxCON (I2Cx Control) ..........................................172 UxTXREG (UARTx Transmit) ..................................184 I2CxMSK (I2Cx Slave Mode Address Mask) ...........176 WKDYHR (RTCC Weekday and Hours Value) ........192 I2CxSTAT (I2Cx Status) ..........................................174 YEAR (RTCC Year Value) .......................................191 ICxCON1 (Input Capture x Control 1) ......................149 Resets ICxCON2 (Input Capture x Control 2) ......................150 Brown-out Reset (BOR) .............................................73 IEC0 (Interrupt Enable Control 0) ..............................90 Clock Source Selection ..............................................72 IEC1 (Interrupt Enable Control 1) ..............................92 Deep Sleep BOR (DSBOR) .......................................73 IEC2 (Interrupt Enable Control 2) ..............................93 Device Times .............................................................72 IEC3 (Interrupt Enable Control 3) ..............................94 RCON Flag Operation ...............................................71 IEC4 (Interrupt Enable Control 4) ..............................95 SFR States ................................................................73 IEC5 (Interrupt Enable Control 5) ..............................96 Revision History ...............................................................353 IFS0 (Interrupt Flag Status 0) ....................................83 DS30009995E-page 358  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY RTCC ...............................................................................185 U Alarm Configuration .................................................196 UART ...............................................................................177 Alarm Mask Settings (figure) ....................................197 Baud Rate Generator (BRG) ...................................178 Calibration ................................................................196 Break and Sync Transmit Sequence .......................179 Module Registers .....................................................186 IrDA Support ............................................................179 Mapping ...........................................................186 Operation of UxCTS and UxRTS Control Pins ........179 Clock Source Selection ............................186 Receiving in 8-Bit or 9-Bit Data Mode .....................179 Write Lock ........................................................186 Transmitting in 8-Bit Data Mode ..............................179 Power Control ..........................................................197 Transmitting in 9-Bit Data Mode ..............................179 Source Clock ............................................................185 Universal Asynchronous Receiver Transmitter. See UART. S W Serial Peripheral Interface (SPI) ......................................161 Watchdog Timer Serial Peripheral Interface. See SPI. Deep Sleep (DSWDT) .............................................250 SFR Space .........................................................................38 Watchdog Timer (WDT) ...................................................248 Software Stack ...................................................................51 Windowed Operation ...............................................249 T WWW Address ................................................................360 WWW, On-Line Support ......................................................9 Timer1 ..............................................................................139 Timer2/3 and Timer4/5 .....................................................141 Timing Diagrams A/D Conversion ........................................................294 Brown-out Reset Characteristics .............................281 CLKO and I/O Timing ...............................................279 External Clock ..........................................................277 I2C Bus Data (Master Mode) ....................................285 I2C Bus Data (Slave Mode) ......................................286 I2C Bus Start/Stop Bits (Master Mode) ....................284 I2C Bus Start/Stop Bits (Slave Mode) ......................287 Input Capture x ........................................................282 Output Compare x ....................................................283 PWM Requirements .................................................283 Reset, Watchdog Timer. Oscillator Start-up Timer, Power-up Timer Characteristics ......................280 SPIx Master Mode (CKE = 0) ..................................289 SPIx Master Mode (CKE = 1) ..................................290 SPIx Slave Mode (CKE = 0) ....................................291 SPIx Slave Mode (CKE = 1) ....................................292 Timer1/2/3/4/5 External Clock Input .........................282 UARTx Baud Rate Generator Output ......................288 UARTx Start Bit Edge Detection ..............................288 Timing Requirements Input Capture x ........................................................282 Output Capture ........................................................283 PWM ........................................................................283 Timer1/2/3/4/5 External Clock Input .........................282  2011-2017 Microchip Technology Inc. DS30009995E-page 359

PIC24FV32KA304 FAMILY NOTES: DS30009995E-page 360  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY THE MICROCHIP WEB SITE CUSTOMER SUPPORT Microchip provides online support via our WWW site at Users of Microchip products can receive assistance www.microchip.com. This web site is used as a means through several channels: to make files and information easily available to • Distributor or Representative customers. Accessible by using your favorite Internet • Local Sales Office browser, the web site contains the following • Field Application Engineer (FAE) information: • Technical Support • Product Support – Data sheets and errata, application notes and sample programs, design Customers should contact their distributor, resources, user’s guides and hardware support representative or Field Application Engineer (FAE) for documents, latest software releases and archived support. Local sales offices are also available to help software customers. A listing of sales offices and locations is • General Technical Support – Frequently Asked included in the back of this document. Questions (FAQ), technical support requests, Technical support is available through the web site online discussion groups, Microchip consultant at: http://microchip.com/support program member listing • Business of Microchip – Product selector and ordering guides, latest Microchip press releases, listing of seminars and events, listings of Microchip sales offices, distributors and factory representatives CUSTOMER CHANGE NOTIFICATION SERVICE Microchip’s customer notification service helps keep customers current on Microchip products. Subscribers will receive e-mail notification whenever there are changes, updates, revisions or errata related to a specified product family or development tool of interest. To register, access the Microchip web site at www.microchip.com. Under “Support”, click on “Customer Change Notification” and follow the registration instructions.  2011-2017 Microchip Technology Inc. DS30009995E-page 361

PIC24FV32KA304 FAMILY NOTES: DS30009995E-page 362  2011-2017 Microchip Technology Inc.

PIC24FV32KA304 FAMILY PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. PIC 24 FV 32 KA3 04 T - I / PT - XXX Examples: a) PIC24FV32KA304-I/ML: Wide voltage range, Microchip Trademark General Purpose, 32-Kbyte program memory, 44-pin, Industrial temp., QFN package Architecture b) PIC24F16KA302-I/SS: Standard voltage range, Flash Memory Family General Purpose, 16-Kbyte program memory, 28-pin, Industrial temp., SSOP package Program Memory Size (KB) Product Group Pin Count Tape and Reel Flag (if applicable) Temperature Range Package Pattern Architecture 24 = 16-bit modified Harvard without DSP Flash Memory Family F = Standard voltage range Flash program memory FV = Wide voltage range Flash program memory Product Group KA3 = General purpose microcontrollers Pin Count 01 = 20-pin 02 = 28-pin 04 = 44-pin Temperature Range I = -40C to +85C (Industrial) E = -40C to +125C (Industrial) Package SP = SPDIP SO = SOIC SS = SSOP ML = QFN P = PDIP PT = TQFP MV = UQFN Pattern Three-digit QTP, SQTP, Code or Special Requirements (blank otherwise) ES = Engineering Sample  2011-2017 Microchip Technology Inc. DS30009995E-page 363

PIC24FV32KA304 FAMILY NOTES: DS30009995E-page 364  2011-2017 Microchip Technology Inc.

Note the following details of the code protection feature on Microchip devices: • Microchip products meet the specification contained in their particular Microchip Data Sheet. • Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. • There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. • Microchip is willing to work with the customer who is concerned about the integrity of their code. • Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as “unbreakable.” Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device Trademarks applications and the like is provided only for your convenience The Microchip name and logo, the Microchip logo, AnyRate, AVR, and may be superseded by updates. It is your responsibility to AVR logo, AVR Freaks, BeaconThings, BitCloud, CryptoMemory, ensure that your application meets with your specifications. CryptoRF, dsPIC, FlashFlex, flexPWR, Heldo, JukeBlox, KEELOQ, MICROCHIP MAKES NO REPRESENTATIONS OR KEELOQ logo, Kleer, LANCheck, LINK MD, maXStylus, WARRANTIES OF ANY KIND WHETHER EXPRESS OR maXTouch, MediaLB, megaAVR, MOST, MOST logo, MPLAB, IMPLIED, WRITTEN OR ORAL, STATUTORY OR OptoLyzer, PIC, picoPower, PICSTART, PIC32 logo, Prochip OTHERWISE, RELATED TO THE INFORMATION, Designer, QTouch, RightTouch, SAM-BA, SpyNIC, SST, SST INCLUDING BUT NOT LIMITED TO ITS CONDITION, Logo, SuperFlash, tinyAVR, UNI/O, and XMEGA are registered QUALITY, PERFORMANCE, MERCHANTABILITY OR trademarks of Microchip Technology Incorporated in the U.S.A. FITNESS FOR PURPOSE. Microchip disclaims all liability and other countries. arising from this information and its use. Use of Microchip ClockWorks, The Embedded Control Solutions Company, devices in life support and/or safety applications is entirely at EtherSynch, Hyper Speed Control, HyperLight Load, IntelliMOS, the buyer’s risk, and the buyer agrees to defend, indemnify and mTouch, Precision Edge, and Quiet-Wire are registered hold harmless Microchip from any and all damages, claims, trademarks of Microchip Technology Incorporated in the U.S.A. suits, or expenses resulting from such use. No licenses are Adjacent Key Suppression, AKS, Analog-for-the-Digital Age, Any conveyed, implicitly or otherwise, under any Microchip Capacitor, AnyIn, AnyOut, BodyCom, chipKIT, chipKIT logo, intellectual property rights unless otherwise stated. CodeGuard, CryptoAuthentication, CryptoCompanion, CryptoController, dsPICDEM, dsPICDEM.net, Dynamic Average Matching, DAM, ECAN, EtherGREEN, In-Circuit Serial Programming, ICSP, Inter-Chip Connectivity, JitterBlocker, KleerNet, KleerNet logo, Mindi, MiWi, motorBench, MPASM, MPF, MPLAB Certified logo, MPLIB, MPLINK, MultiTRAK, NetDetach, Omniscient Code Generation, PICDEM, PICDEM.net, PICkit, PICtail, PureSilicon, QMatrix, RightTouch logo, REAL ICE, Ripple Blocker, SAM-ICE, Serial Quad I/O, SMART-I.S., SQI, SuperSwitcher, SuperSwitcher II, Total Endurance, TSHARC, USBCheck, VariSense, ViewSpan, WiperLock, Wireless DNA, and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in Microchip received ISO/TS-16949:2009 certification for its worldwide the U.S.A. headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California Silicon Storage Technology is a registered trademark of Microchip and India. The Company’s quality system processes and procedures Technology Inc. in other countries. are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and GestIC is a registered trademark of Microchip Technology analog products. In addition, Microchip’s quality system for the design Germany II GmbH & Co. KG, a subsidiary of Microchip Technology and manufacture of development systems is ISO 9001:2000 certified. Inc., in other countries. All other trademarks mentioned herein are property of their QUALITY MANAGEMENT SYSTEM respective companies. © 2011-2017, Microchip Technology Incorporated, All Rights CERTIFIED BY DNV Reserved. ISBN: 978-1-5224-2236-5 == ISO/TS 16949 ==  2011-2017 Microchip Technology Inc. DS30009995E-page 365

Worldwide Sales and Service AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office Asia Pacific Office China - Xiamen Austria - Wels 2355 West Chandler Blvd. Suites 3707-14, 37th Floor Tel: 86-592-2388138 Tel: 43-7242-2244-39 Chandler, AZ 85224-6199 Tower 6, The Gateway Fax: 86-592-2388130 Fax: 43-7242-2244-393 Tel: 480-792-7200 Harbour City, Kowloon China - Zhuhai Denmark - Copenhagen Fax: 480-792-7277 Hong Kong Tel: 86-756-3210040 Tel: 45-4450-2828 Technical Support: Tel: 852-2943-5100 Fax: 86-756-3210049 Fax: 45-4485-2829 http://www.microchip.com/ Fax: 852-2401-3431 India - Bangalore Finland - Espoo support Australia - Sydney Tel: 91-80-3090-4444 Tel: 358-9-4520-820 Web Address: www.microchip.com Tel: 61-2-9868-6733 Fax: 91-80-3090-4123 France - Paris Fax: 61-2-9868-6755 India - New Delhi Tel: 33-1-69-53-63-20 Atlanta China - Beijing Tel: 91-11-4160-8631 Fax: 33-1-69-30-90-79 Duluth, GA Tel: 678-957-9614 Tel: 86-10-8569-7000 Fax: 91-11-4160-8632 Germany - Garching Fax: 678-957-1455 Fax: 86-10-8528-2104 India - Pune Tel: 49-8931-9700 China - Chengdu Tel: 91-20-3019-1500 Germany - Haan ATeul:s 5ti1n2, -T2X57-3370 Tel: 86-28-8665-5511 Japan - Osaka Tel: 49-2129-3766400 Fax: 86-28-8665-7889 Tel: 81-6-6152-7160 Germany - Heilbronn Boston China - Chongqing Fax: 81-6-6152-9310 Tel: 49-7131-67-3636 Westborough, MA Tel: 774-760-0087 Tel: 86-23-8980-9588 Japan - Tokyo Germany - Karlsruhe Fax: 86-23-8980-9500 Tel: 81-3-6880- 3770 Tel: 49-721-625370 Fax: 774-760-0088 China - Dongguan Fax: 81-3-6880-3771 Germany - Munich CItahsiccaa,g IoL Tel: 86-769-8702-9880 Korea - Daegu Tel: 49-89-627-144-0 Tel: 630-285-0071 China - Guangzhou Tel: 82-53-744-4301 Fax: 49-89-627-144-44 Fax: 630-285-0075 Tel: 86-20-8755-8029 Fax: 82-53-744-4302 Germany - Rosenheim China - Hangzhou Korea - Seoul Tel: 49-8031-354-560 Dallas Addison, TX Tel: 86-571-8792-8115 Tel: 82-2-554-7200 Israel - Ra’anana Tel: 972-818-7423 Fax: 86-571-8792-8116 Fax: 82-2-558-5932 or Tel: 972-9-744-7705 Fax: 972-818-2924 China - Hong Kong SAR 82-2-558-5934 Italy - Milan Detroit Tel: 852-2943-5100 Malaysia - Kuala Lumpur Tel: 39-0331-742611 Novi, MI Fax: 852-2401-3431 Tel: 60-3-6201-9857 Fax: 39-0331-466781 Tel: 248-848-4000 China - Nanjing Fax: 60-3-6201-9859 Italy - Padova Houston, TX Tel: 86-25-8473-2460 Malaysia - Penang Tel: 39-049-7625286 Fax: 86-25-8473-2470 Tel: 60-4-227-8870 Tel: 281-894-5983 Netherlands - Drunen Indianapolis China - Qingdao Fax: 60-4-227-4068 Tel: 31-416-690399 Noblesville, IN Tel: 86-532-8502-7355 Philippines - Manila Fax: 31-416-690340 Fax: 86-532-8502-7205 Tel: 63-2-634-9065 Tel: 317-773-8323 Norway - Trondheim Fax: 317-773-5453 China - Shanghai Fax: 63-2-634-9069 Tel: 47-7289-7561 Tel: 317-536-2380 Tel: 86-21-3326-8000 Singapore Poland - Warsaw Fax: 86-21-3326-8021 Tel: 65-6334-8870 Los Angeles Tel: 48-22-3325737 Mission Viejo, CA China - Shenyang Fax: 65-6334-8850 Romania - Bucharest Tel: 949-462-9523 Tel: 86-24-2334-2829 Taiwan - Hsin Chu Tel: 40-21-407-87-50 Fax: 949-462-9608 Fax: 86-24-2334-2393 Tel: 886-3-5778-366 Tel: 951-273-7800 China - Shenzhen Fax: 886-3-5770-955 Spain - Madrid Tel: 34-91-708-08-90 Raleigh, NC Tel: 86-755-8864-2200 Taiwan - Kaohsiung Fax: 34-91-708-08-91 Tel: 919-844-7510 Fax: 86-755-8203-1760 Tel: 886-7-213-7830 Sweden - Gothenberg New York, NY China - Wuhan Taiwan - Taipei Tel: 46-31-704-60-40 Tel: 631-435-6000 Tel: 86-27-5980-5300 Tel: 886-2-2508-8600 Fax: 86-27-5980-5118 Fax: 886-2-2508-0102 Sweden - Stockholm San Jose, CA Tel: 46-8-5090-4654 Tel: 408-735-9110 China - Xian Thailand - Bangkok Tel: 408-436-4270 Tel: 86-29-8833-7252 Tel: 66-2-694-1351 UK - Wokingham Fax: 86-29-8833-7256 Fax: 66-2-694-1350 Tel: 44-118-921-5800 Canada - Toronto Fax: 44-118-921-5820 Tel: 905-695-1980 Fax: 905-695-2078 DS30009995E-page 366  2011-2017 Microchip Technology Inc. 10/10/17