PIC18F66K80 FAMILY 28/40/44/64-Pin, High-Temperature, Enhanced Flash Microcontrollers with ECAN™ and nanoWatt XLP Technology High-Temperature Features: ECAN Bus Module Features (Continued): • Ambient Temperature Range of -40°C to +150°C • Six Programmable Receive/Transmit Buffers • Three Dedicated Transmit Buffers with Prioritiza- Power-Managed Modes: tion • Run: CPU on, Peripherals on • Two Dedicated Receive Buffers • Idle: CPU off, Peripherals on • 16 Full, 29-Bit Acceptance Filters with Dynamic Association • Sleep: CPU off, Peripherals off • Three Full, 29-Bit Acceptance Masks • Two-Speed Oscillator Start-up • Automatic Remote Frame Handling • Fail-Safe Clock Monitor (FSCM) • Advanced Error Management Features • Power-Saving Peripheral Module Disable (PMD) • Ultra Low-Power Wake-up Special Microcontroller Features: • Fast Wake-up, 1 µs, Typical • On-Chip 3.3V Regulator • Low-Power WDT, 300 nA, Typical • Operating Speed up to 64 MHz • Run mode Currents Down to Very Low 3.8 µA, Typical • 3.6 Kbytes of General Purpose Registers (SRAM) • Idle mode Currents Down to Very Low 880 nA, • Three Internal Oscillators: Typical - LF-INTOSC (31kHz) • Sleep mode Currents Down to Very Low 13 nA, - MF-INTOSC (500kHz) Typical - HF-INTOSC (16MHz) • Priority Levels for Interrupts ECAN Bus Module Features: • 8 x 8 Single-Cycle Hardware Multiplier • Conforms to CAN 2.0B Active Specification • Extended Watchdog Timer (WDT): • Three Operating modes: - Programmable period from 4ms to 4,194s - Legacy mode (full backward compatibility with • In-Circuit Serial Programming™ (ICSP™) via Two existing PIC18CXX8/FXX8 CAN modules) Pins - Enhanced mode • In-Circuit Debug via Two Pins - FIFO mode or programmable TX/RX buffers • Programmable BOR • Message Bit Rates up to 1Mbps • Programmable LVD • DeviceNet™ Data Byte Filter Support TABLE 1: DEVICE COMPARISON s D Device PMreomgroarmy M(BeDymatteoasr )y (BDEyatEteas ) Pins I/O CTMU 12-Bit A/DChannels CCP/ECCP Timers8-Bit/16-Bit EUSART Comparator ECAN™ MSSP BORMV/LV DSM PIC18F25K80 32Bytes 3,648 1,024 28 24 1 8-ch 4/1 2/3 2 2 1 1 Yes No PIC18F26K80 64Bytes 3,648 1,024 28 24 1 8-ch 4/1 2/3 2 2 1 1 Yes No PIC18F45K80 32Bytes 3,648 1,024 40/44 35 1 11-ch 4/1 2/3 2 2 1 1 Yes No PIC18F46K80 64Bytes 3,648 1,024 40/44 35 1 11-ch 4/1 2/3 2 2 1 1 Yes No PIC18F65K80 32Bytes 3,648 1,024 64 54 1 11-ch 4/1 2/3 2 2 1 1 Yes Yes PIC18F66K80 64Bytes 3,648 1,024 64 54 1 11-ch 4/1 2/3 2 2 1 1 Yes Yes  2012 Microchip Technology Inc. DS30509A-page 1

PIC18F66K80 FAMILY Peripheral Highlights: • Up to Four External Interrupts • One Master Synchronous Serial Port • Five CCP/ECCP modules: (MSSP) module: - Four Capture/Compare/PWM (CCP) modules - 3/4-wire SPI (supports all four SPI modes) - One Enhanced Capture/Compare/PWM (ECCP) module - I2C™ Master and Slave modes • Five 8/16-Bit Timer/Counter modules: • Two Enhanced Addressable USART modules: - Timer0: 8/16-bit timer/counter with 8-bit - LIN/J2602 support programmable prescaler - Auto-Baud Detect (ABD) - Timer1, Timer3: 16-bit timer/counter • 12-Bit A/D Converter with up to 11 Channels: - Timer2, Timer4: 8-bit timer/counter - Auto-acquisition and Sleep operation • Two Analog Comparators - Differential Input mode of operation • Configurable Reference Clock Output • Data Signal Modulator module: • Charge Time Measurement Unit (CTMU): - Select modulator and carrier sources from - Capacitance measurement various module outputs - Time measurement with 1ns typical resolution • Integrated Voltage Reference - Integrated voltage reference DS30509A-page 2  2012 Microchip Technology Inc.

PIC18F66K80 FAMILY Table of Contents 1.0 Device Overview..........................................................................................................................................................................5 2.0 Special Features of the CPU........................................................................................................................................................7 3.0 Electrical Characteristics..............................................................................................................................................................9 Appendix A: Revision History...............................................................................................................................................................13 The Microchip Web Site.......................................................................................................................................................................15 Customer Change Notification Service................................................................................................................................................15 Customer Support................................................................................................................................................................................15 Reader Response................................................................................................................................................................................16 Product Identification System..............................................................................................................................................................17  2012 Microchip Technology Inc. DS30509A-page 3

PIC18F66K80 FAMILY TO OUR VALUED CUSTOMERS It is our intention to provide our valued customers with the best documentation possible to ensure successful use of your Microchip products. To this end, we will continue to improve our publications to better suit your needs. Our publications will be refined and enhanced as new volumes and updates are introduced. If you have any questions or comments regarding this publication, please contact the Marketing Communications Department via E-mail at docerrors@microchip.com or fax the Reader Response Form in the back of this data sheet to (480) 792-4150. We welcome your feedback. Most Current Data Sheet To obtain the most up-to-date version of this data sheet, please register at our Worldwide Web site at: http://www.microchip.com You can determine the version of a data sheet by examining its literature number found on the bottom outside corner of any page. The last character of the literature number is the version number, (e.g., DS30000A is version A of document DS30000). Errata An errata sheet, describing minor operational differences from the data sheet and recommended workarounds, may exist for current devices. As device/documentation issues become known to us, we will publish an errata sheet. The errata will specify the revision of silicon and revision of document to which it applies. To determine if an errata sheet exists for a particular device, please check with one of the following: • Microchip’s Worldwide Web site; http://www.microchip.com • Your local Microchip sales office (see last page) When contacting a sales office, please specify which device, revision of silicon and data sheet (include literature number) you are using. Customer Notification System Register on our web site at www.microchip.com to receive the most current information on all of our products. DS30509A-page 4  2012 Microchip Technology Inc.

PIC18F66K80 FAMILY 1.0 DEVICE OVERVIEW The primary differentiating features and specifications of the high-temperature PIC18F66K80 family devices This document contains device-specific information for are: the following devices, operating in an ambient • Above +125°C, writes are not allowed for Flash temperature range between -40°C and +150°C: program memory • PIC18F25K80 • PIC18F46K80 • All AC timing specifications are increased by 15% • PIC18F26K80 • PIC18F65K80 This derating factor includes parameters, such as • PIC18F45K80 • PIC18F66K80 TPWRT • Maximum HS frequency of operation is 64MHz Note: This data sheet documents only the devices’ features and specifications that are in Note: The test duration for AEC-Q100 reliability addition to the features and specifications of testing for devices operating at +150°C is the non-specialty PIC18F66K80 devices. 1,000 hours. Any design operating at For information on the features and +125°C to +150°C for longer than that specifications shared by this document’s high- period is not warranted without prior written temperature devices and the non-specialty approval from Microchip Technology Inc. devices, see the “PIC18F66K80 Family Data Sheet” (DS39977). This family of devices offers the advantages of all PIC18 microcontrollers; namely, high computational performance at an economical price. In addition to these features, the PIC18F66K80 family introduces design enhancements that make these microcontrollers a logical choice for many high-performance, power-sensitive applications.  2012 Microchip Technology Inc. DS30509A-page 5

PIC18F66K80 FAMILY NOTES: DS30509A-page 6  2012 Microchip Technology Inc.

PIC18F66K80 FAMILY 2.0 SPECIAL FEATURES OF THE 2.1 Device ID Registers CPU The Device ID registers are read-only registers. They identify the device type and revision for device Note: For additional details on the Configuration bits, programmers and can be read by firmware using table refer to Section 28.1 “Configuration Bits” in reads. the “PIC18F66K80 Family Data Sheet” (DS39977). Device ID information presented in this section is for the high-temperature PIC18F66K80 family devices only. TABLE 2-1: DEVICE IDs Default/ File Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Unprogrammed Value 3FFFFEh DEVID1(1) DEV2 DEV1 DEV0 REV4 REV3 REV2 REV1 REV0 xxxx xxxx 3FFFFFh DEVID2(1) DEV10 DEV9 DEV8 DEV7 DEV6 DEV5 DEV4 DEV3 xxxx xxxx Legend: x = unknown; u = unchanged,;— = unimplemented. Note 1: See Register2-1 and Register2-2 for DEVIDx values. DEVIDx registers are read-only and cannot be programmed by the user. REGISTER 2-1: DEVID1: DEVICE ID REGISTER 1 R R R R R R R R DEV2(1) DEV1(1) DEV0(1) REV4 REV3 REV2 REV1 REV0 bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7-5 DEV<2:0>: Device ID bits(1) 111 = PIC18F66K80 100 = PIC18F25K80 011 = PIC18F45K80 010 = PIC18F65K80 001 = PIC18F26K80 000 = PIC18F46K80 bit 4-0 REV<4:0>: Revision ID bits These bits are used to indicate the device revision. Note 1: These DEV<2:0> values may be shared with other devices. The specific device is always identified by using the entire DEV<10:0> bit sequence.  2012 Microchip Technology Inc. DS30509A-page 7

PIC18F66K80 FAMILY REGISTER 2-2: DEVID2: DEVICE ID REGISTER 2 R R R R R R R R DEV10(1) DEV9(1) DEV8(1) DEV7(1) DEV6(1) DEV5(1) DEV4(1) DEV3(1) bit 7 bit 0 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown bit 7-0 DEV<10:3>: Device ID bits(1) 0110 0000 = PIC18F66K80 0110 0001 = PIC18F46K80, PIC18F26K80, PIC18F65K80, PIC18F45K80, PIC18F25K80 Note 1: These DEV<10:3> values may be shared with other devices. The specific device is always identified by using the entire DEV<10:0> bit sequence. DS30509A-page 8  2012 Microchip Technology Inc.

PIC18F66K80 FAMILY 3.0 ELECTRICAL CHARACTERISTICS Note: Other than some basic data, this section documents only the high-temperature PIC18F66K80 family devices’ specifications that differ from those of the non-specialty PIC18F66K80 family devices. For detailed information on the electrical specifications shared by the high-temperature and non-specialty devices, see the “PIC18F66K80 Family Data Sheet” (DS39977). Unless otherwise noted, this section’s parameters assume a minimum voltage of 4.0V. 3.1 Absolute Maximum Ratings(†) Ambient temperature under bias...........................................................................................................................+150°C Maximum current out of VSS pin.............................................................................................................................60 mA Maximum current into VDD pin................................................................................................................................60 mA Maximum output current sunk by any I/O pin(1)........................................................................................................1 mA Maximum output current sourced by any I/O pin(1)...................................................................................................1 mA Maximum current sunk by all ports combined(1).....................................................................................................10 mA Maximum current sourced by all ports combined(1)................................................................................................10 mA Note 1: Maximum allowable current is a function of device maximum power dissipation (see Section 31.0 “Electrical Characteristics” in the “PIC18F66K80 Family Data Sheet”. †NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. FIGURE 3-1: PIC18F66K80 VOLTAGE-FREQUENCY GRAPH (HIGH TEMPERATURE) 6.0V 5.5V 5.0V 4.5V 4.0V 4.0V e g 3.5V a t ol 3.0V V 2.5V 2.0V 64 MHz Frequency High-Temperature Devices  2012 Microchip Technology Inc. DS30509A-page 9

PIC18F66K80 FAMILY 3.2 DC Characteristics: Supply Voltage (High Temperature) PIC18F66K80 Family Standard Operating Conditions (unless otherwise stated) (High Temperature) Operating temperature +125°C  TA  +150°C for high temperature Param Symbol Characteristic Min Typ Max Units Conditions No. D001 VDD Supply Voltage 4.0 — 5.5 V For F devices 3.3 DC Characteristics: Power Down and Supply Current (High Temperature) PIC18F66K80 Family Standard Operating Conditions (unless otherwise stated) (High Temperature) Operating temperature +125°C  TA  +150°C for high temperature Param Device Typ Max Units Conditions No. PIC18FXXK80 Power-Down Current (IPD)(1) 10 28 µA +150°C VDD = 5V, Sleep mode Module Differential Currents 12 29 µA +150°C VDD = 5V, Watchdog Timer Current: ΔIWDT 12 28 µA +150°C VDD = 5V, A/D Current: ΔIAD 12 28 µA +150°C VDD = 5V, High/Low-Voltage Detect: ΔIHLVD Supply Current (IDD)(2,3) 10 32 mA +150°C VDD = 5V, FOSC = 64 MHz (PRI_RUN mode) — 8 mA +150°C VDD = 5V, FOSC = 4 MHz (PRI_RUN mode) — 3 mA +150°C VDD = 5V, FOSC = 1 MHz (PRI_RUN mode) — 8 mA +150°C VDD = 5V, FOSC = 64 MHz (PRI_IDLE mode) — 1.8 mA +150°C VDD = 5V, FOSC = 4 MHz (PRI_IDLE mode) — 1 mA +150°C VDD = 5V, FOSC = 1 MHz (PRI_IDLE mode) — 28 mA +150°C VDD = 5V, FOSC = 64 MHz (PRI_RUN mode, 16 MHz w/PLL) — 8 mA +150°C VDD = 5V, FOSC = 16 MHz (PRI_RUN mode, 4 MHz w/PLL) Note 1: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with the part in Sleep mode, with all I/O pins in a high-impedance state and tied to VDD or VSS, and all features that add delta current are disabled (such as WDT, secondary oscillator, BOR, etc.). 2: The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on the current consumption. 3: The test conditions for all IDD measurements in active operation mode are: OSC1 = External square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD; MCLR = VDD; WDT is enabled/disabled as specified. DS30509A-page 10  2012 Microchip Technology Inc.

PIC18F66K80 FAMILY 3.4 DC Characteristics: PIC18F66K80 Family (High Temperature) PIC18F66K80 Family Standard Operating Conditions (unless otherwise stated) (High Temperature) Operating temperature +125°C  TA  +150°C for high temperature Param Symbol Characteristic Min Typ Max Units Conditions No. D031 VIL I/O Ports with Schmitt Trigger VSS — 0.25 VDD V VDD = 5.0V Buffer D032 VIL MCLR VSS — 0.25 VDD V VDD = 5.0V D041 VIH I/O Ports with Schmitt Trigger 0.85 VDD — VDD V VDD = 5.0V Buffer D042 VIH MCLR, OSC1 (EC mode) 0.85 VDD — VDD V VDD = 5.0V D060 IIL Input Leakage Current — — ±2 µA VSS ≤ VPIN ≤ VDD, I/O Ports Pin at high-impedance 3.5 DC Characteristics: Memory Programming Requirements PIC18F66K80 Family Standard Operating Conditions (unless otherwise stated) (High Temperature) Operating temperature +125°C  TA  +150°C for high temperature Param Symbol Characteristic Min Typ Max Units Conditions No. D120 ED Data EEPROM Memory Byte 50K — — E/W +125°C to +150°C Endurance D121 VDRW VDD for Read/Write 4.0 — 5.5 V Using EECON to read/write PIC18FXXKXX devices D123 VRETD Characteristic Retention 1 — — Year Provided no other specifications are violated  2012 Microchip Technology Inc. DS30509A-page 11

PIC18F66K80 FAMILY 3.6 AC Characteristics Internal RC Accuracy (INTOSC) PIC18F66K80 Family Standard Operating Conditions (unless otherwise stated) (High Temperature) Operating temperature -40°C  TA  +150°C Param Min Typ Max Units Conditions No. INTOSC Accuracy @ Freq = 16 MHz, 8 MHz, 4 MHz, 2 MHz, 1 MHz, 500 kHz, 250 kHz(1) OA1 -20 — ±20 % +125°C to +150°C, VDD = 4.0-5.5V OA2 LF_INTOSC Accuracy @ 31 kHz OA2 -25 — ±25 % VDD = 4.0-5.5V Note 1: Frequency is calibrated at +25°C. The OSCTUNE register can be used to compensate for temperature drift. TABLE 3-1: DC CHARACTERISTICS: HIGH/LOW-VOLTAGE DETECT CHARACTERISTICS PIC18F66K80 Family Standard Operating Conditions (unless otherwise stated) (High Temperature) Operating temperature -40°C  TA  +150°C Param Characteristic Min Typ Max Units No. D420 HLVD Voltage on VDD, HLVDL<3:0> = 1101 4.00 4.44 4.88 V Transition High-to-Low HLVDL<3:0> = 1110 4.28 4.75 5.23 V DS30509A-page 12  2012 Microchip Technology Inc.

PIC18F66K80 APPENDIX A: REVISION HISTORY Revision A (February 2012) Original mini data sheet for the high-temperature devices in the PIC18F66K80 family. DS30509A-page 13  2012 Microchip Technology Inc.

PIC18F66K80 NOTES: DS30509A-page 14  2012 Microchip Technology Inc.

PIC18F66K80 FAMILY THE MICROCHIP WEB SITE CUSTOMER SUPPORT Microchip provides online support via our WWW site at Users of Microchip products can receive assistance www.microchip.com. This web site is used as a means through several channels: to make files and information easily available to • Distributor or Representative customers. Accessible by using your favorite Internet • Local Sales Office browser, the web site contains the following • Field Application Engineer (FAE) information: • Technical Support • Product Support – Data sheets and errata, • Development Systems Information Line application notes and sample programs, design resources, user’s guides and hardware support Customers should contact their distributor, documents, latest software releases and archived representative or field application engineer (FAE) for software support. Local sales offices are also available to help • General Technical Support – Frequently Asked customers. A listing of sales offices and locations is Questions (FAQ), technical support requests, included in the back of this document. online discussion groups, Microchip consultant Technical support is available through the web site program member listing at: http://microchip.com/support • Business of Microchip – Product selector and ordering guides, latest Microchip press releases, listing of seminars and events, listings of Microchip sales offices, distributors and factory representatives CUSTOMER CHANGE NOTIFICATION SERVICE Microchip’s customer notification service helps keep customers current on Microchip products. Subscribers will receive e-mail notification whenever there are changes, updates, revisions or errata related to a specified product family or development tool of interest. To register, access the Microchip web site at www.microchip.com. Under “Support”, click on “Customer Change Notification” and follow the registration instructions.  2012 Microchip Technology Inc. DS30509A-page 15

PIC18F66K80 FAMILY READER RESPONSE It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip product. If you wish to provide your comments on organization, clarity, subject matter, and ways in which our documentation can better serve you, please FAX your comments to the Technical Publications Manager at (480)792-4150. Please list the following information, and use this outline to provide us with your comments about this document. TO: Technical Publications Manager Total Pages Sent ________ RE: Reader Response From: Name Company Address City / State / ZIP / Country Telephone: (_______) _________ - _________ FAX: (______) _________ - _________ Application (optional): Would you like a reply? Y N Device: PIC18F66K80 Family Literature Number: DS30509A Questions: 1. What are the best features of this document? 2. How does this document meet your hardware and software development needs? 3. Do you find the organization of this document easy to follow? If not, why? 4. What additions to the document do you think would enhance the structure and subject? 5. What deletions from the document could be made without affecting the overall usefulness? 6. Is there any incorrect or misleading information (what and where)? 7. How would you improve this document? DS30509A-page 16  2012 Microchip Technology Inc.

PIC18F66K80 FAMILY PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. PART NO. X /XX XXX Examples: Device Temperature Package Pattern a) PIC18F46K80T-H/PT = High Temperature, Range TQFP package in tape and reel configuration Device(1,2) PIC18F25K80/26K80, PIC18F45K80/46K80, PIC18F65K80/66K80, PIC18F25K80/26K80T, PIC18F45K80/46K80T, PIC18F65K80/ 66K80T VDD range 4.0V to 5.5V Temperature I = -40C to +85C (Industrial) Range E = -40C to +125C (Extended) H = -40C to +150C (High Temperature) Package PT = TQFP Thin Quad Flatpack MR = QFN Plastic Quad Flat, No Lead Package SS = SSOP Plastic Shrink Small Outline Note1: F = Standard Voltage Range MM = QFN Plastic Quad Flat, No Lead Package 2: LF = Wide Voltage Range ML = QFN Plastic Quad Flat, No Lead Package 3: T = In Tape and Reel PLCC, and TQFP packages only Pattern QTP, SQTP, Code or Special Requirements (blank otherwise)  2012 Microchip Technology Inc. DS30509A-page 17

PIC18F66K80 FAMILY NOTES: DS30509A-page 18  2012 Microchip Technology Inc.

Note the following details of the code protection feature on Microchip devices: • Microchip products meet the specification contained in their particular Microchip Data Sheet. • Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. • There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. • Microchip is willing to work with the customer who is concerned about the integrity of their code. • Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as “unbreakable.” Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device Trademarks applications and the like is provided only for your convenience The Microchip name and logo, the Microchip logo, dsPIC, and may be superseded by updates. It is your responsibility to KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART, ensure that your application meets with your specifications. PIC32 logo, rfPIC and UNI/O are registered trademarks of MICROCHIP MAKES NO REPRESENTATIONS OR Microchip Technology Incorporated in the U.S.A. and other WARRANTIES OF ANY KIND WHETHER EXPRESS OR countries. IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor, INCLUDING BUT NOT LIMITED TO ITS CONDITION, MXDEV, MXLAB, SEEVAL and The Embedded Control QUALITY, PERFORMANCE, MERCHANTABILITY OR Solutions Company are registered trademarks of Microchip FITNESS FOR PURPOSE. Microchip disclaims all liability Technology Incorporated in the U.S.A. arising from this information and its use. Use of Microchip Analog-for-the-Digital Age, Application Maestro, chipKIT, devices in life support and/or safety applications is entirely at chipKIT logo, CodeGuard, dsPICDEM, dsPICDEM.net, the buyer’s risk, and the buyer agrees to defend, indemnify and dsPICworks, dsSPEAK, ECAN, ECONOMONITOR, hold harmless Microchip from any and all damages, claims, FanSense, HI-TIDE, In-Circuit Serial Programming, ICSP, suits, or expenses resulting from such use. No licenses are Mindi, MiWi, MPASM, MPLAB Certified logo, MPLIB, conveyed, implicitly or otherwise, under any Microchip MPLINK, mTouch, Omniscient Code Generation, PICC, intellectual property rights. PICC-18, PICDEM, PICDEM.net, PICkit, PICtail, REAL ICE, rfLAB, Select Mode, Total Endurance, TSHARC, UniWinDriver, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. © 2012, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. ISBN: 978-1-62076-016-1 Microchip received ISO/TS-16949:2009 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company’s quality system processes and procedures are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001:2000 certified.  2012 Microchip Technology Inc. DS30509A-page 19

Worldwide Sales and Service AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office Asia Pacific Office India - Bangalore Austria - Wels 2355 West Chandler Blvd. Suites 3707-14, 37th Floor Tel: 91-80-3090-4444 Tel: 43-7242-2244-39 Chandler, AZ 85224-6199 Tower 6, The Gateway Fax: 91-80-3090-4123 Fax: 43-7242-2244-393 Tel: 480-792-7200 Harbour City, Kowloon India - New Delhi Denmark - Copenhagen Fax: 480-792-7277 Hong Kong Tel: 91-11-4160-8631 Tel: 45-4450-2828 Technical Support: Tel: 852-2401-1200 Fax: 91-11-4160-8632 Fax: 45-4485-2829 http://www.microchip.com/ support Fax: 852-2401-3431 India - Pune France - Paris Web Address: Australia - Sydney Tel: 91-20-2566-1512 Tel: 33-1-69-53-63-20 www.microchip.com Tel: 61-2-9868-6733 Fax: 91-20-2566-1513 Fax: 33-1-69-30-90-79 Atlanta Fax: 61-2-9868-6755 Japan - Osaka Germany - Munich Duluth, GA China - Beijing Tel: 81-66-152-7160 Tel: 49-89-627-144-0 Tel: 86-10-8569-7000 Fax: 49-89-627-144-44 Tel: 678-957-9614 Fax: 81-66-152-9310 Fax: 678-957-1455 Fax: 86-10-8528-2104 Japan - Yokohama Italy - Milan China - Chengdu Tel: 39-0331-742611 Boston Tel: 81-45-471- 6166 Tel: 86-28-8665-5511 Fax: 39-0331-466781 Westborough, MA Fax: 81-45-471-6122 Tel: 774-760-0087 Fax: 86-28-8665-7889 Korea - Daegu Netherlands - Drunen Fax: 774-760-0088 China - Chongqing Tel: 82-53-744-4301 Tel: 31-416-690399 Chicago Tel: 86-23-8980-9588 Fax: 82-53-744-4302 Fax: 31-416-690340 Itasca, IL Fax: 86-23-8980-9500 Korea - Seoul Spain - Madrid Tel: 630-285-0071 China - Hangzhou Tel: 82-2-554-7200 Tel: 34-91-708-08-90 Fax: 630-285-0075 Tel: 86-571-2819-3187 Fax: 82-2-558-5932 or Fax: 34-91-708-08-91 Cleveland Fax: 86-571-2819-3189 82-2-558-5934 UK - Wokingham Independence, OH China - Hong Kong SAR Malaysia - Kuala Lumpur Tel: 44-118-921-5869 Tel: 216-447-0464 Tel: 852-2401-1200 Tel: 60-3-6201-9857 Fax: 44-118-921-5820 Fax: 216-447-0643 Fax: 852-2401-3431 Fax: 60-3-6201-9859 Dallas China - Nanjing Malaysia - Penang Addison, TX Tel: 86-25-8473-2460 Tel: 60-4-227-8870 Tel: 972-818-7423 Fax: 86-25-8473-2470 Fax: 60-4-227-4068 Fax: 972-818-2924 China - Qingdao Philippines - Manila Detroit Tel: 86-532-8502-7355 Tel: 63-2-634-9065 Farmington Hills, MI Fax: 86-532-8502-7205 Fax: 63-2-634-9069 Tel: 248-538-2250 Fax: 248-538-2260 China - Shanghai Singapore Tel: 86-21-5407-5533 Tel: 65-6334-8870 Indianapolis Fax: 86-21-5407-5066 Fax: 65-6334-8850 Noblesville, IN Tel: 317-773-8323 China - Shenyang Taiwan - Hsin Chu Fax: 317-773-5453 Tel: 86-24-2334-2829 Tel: 886-3-5778-366 Fax: 86-24-2334-2393 Fax: 886-3-5770-955 Los Angeles Mission Viejo, CA China - Shenzhen Taiwan - Kaohsiung Tel: 949-462-9523 Tel: 86-755-8203-2660 Tel: 886-7-536-4818 Fax: 949-462-9608 Fax: 86-755-8203-1760 Fax: 886-7-330-9305 Santa Clara China - Wuhan Taiwan - Taipei Santa Clara, CA Tel: 86-27-5980-5300 Tel: 886-2-2500-6610 Tel: 408-961-6444 Fax: 86-27-5980-5118 Fax: 886-2-2508-0102 Fax: 408-961-6445 China - Xian Thailand - Bangkok Toronto Tel: 86-29-8833-7252 Tel: 66-2-694-1351 Mississauga, Ontario, Fax: 86-29-8833-7256 Fax: 66-2-694-1350 Canada China - Xiamen Tel: 905-673-0699 Tel: 86-592-2388138 Fax: 905-673-6509 Fax: 86-592-2388130 China - Zhuhai Tel: 86-756-3210040 11/29/11 Fax: 86-756-3210049 DS30509A-page 20  2012 Microchip Technology Inc.

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: M icrochip: PIC18F25K80-E/ML PIC18F25K80-E/SO PIC18F25K80-E/SP PIC18F25K80-E/SS PIC18F25K80-I/ML PIC18F25K80-I/SO PIC18F25K80-I/SP PIC18F25K80-I/SS PIC18F25K80T-I/ML PIC18F25K80T-I/SO PIC18F25K80T-I/SS PIC18F26K80-E/ML PIC18F26K80-E/SO PIC18F26K80-E/SP PIC18F26K80-E/SS PIC18F26K80-I/ML PIC18F26K80-I/SO PIC18F26K80-I/SP PIC18F26K80-I/SS PIC18F26K80T-I/ML PIC18F26K80T- I/SO PIC18F26K80T-I/SS PIC18F45K80-E/ML PIC18F45K80-E/P PIC18F45K80-E/PT PIC18F45K80-I/ML PIC18F45K80-I/P PIC18F45K80-I/PT PIC18F45K80T-I/ML PIC18F45K80T-I/PT PIC18F46K80-E/ML PIC18F46K80- E/P PIC18F46K80-E/PT PIC18F46K80-I/ML PIC18F46K80-I/P PIC18F46K80-I/PT PIC18F46K80T-I/ML PIC18F46K80T-I/PT PIC18F65K80-E/MR PIC18F65K80-E/PT PIC18F65K80-I/MR PIC18F65K80-I/PT PIC18F65K80T-I/MR PIC18F65K80T-I/PT PIC18F66K80-E/MR PIC18F66K80-E/PT PIC18F66K80-I/MR PIC18F66K80-I/PT PIC18F66K80T-I/MR PIC18F66K80T-I/PT PIC18LF25K80-I/ML PIC18LF25K80-I/SO PIC18LF25K80-I/SP PIC18LF25K80-I/SS PIC18LF25K80T-I/ML PIC18LF25K80T-I/SO PIC18LF25K80T-I/SS PIC18LF26K80-I/ML PIC18LF26K80-I/SO PIC18LF26K80-I/SP PIC18LF26K80-I/SS PIC18LF26K80T-I/ML PIC18LF26K80T-I/SO PIC18LF26K80T-I/SS PIC18LF45K80-I/ML PIC18LF45K80-I/P PIC18LF45K80-I/PT PIC18LF45K80T-I/ML PIC18LF45K80T-I/PT PIC18LF46K80-I/ML PIC18LF46K80-I/P PIC18LF46K80-I/PT PIC18LF46K80T-I/ML PIC18LF46K80T-I/PT PIC18LF65K80-I/MR PIC18LF65K80-I/PT PIC18LF65K80T-I/PT PIC18LF66K80-I/MR PIC18LF66K80-I/PT PIC18LF66K80T-I/PT PIC18F25K80-H/SS PIC18F26K80-H/MM PIC18F26K80-H/SS PIC18F45K80-H/PT PIC18F46K80-H/ML PIC18F46K80-H/PT PIC18F65K80-H/MR PIC18F66K80-H/MR PIC18F66K80-H/PT PIC18F65K80-H/PT PIC18F25K80-H/MM PIC18F45K80-H/ML PIC18LF65K80T-I/MR PIC18LF66K80T-I/MR PIC18F25K80-E/MM PIC18F25K80-I/MM PIC18F25K80T-I/MM PIC18F26K80-E/MM PIC18F26K80-I/MM PIC18F26K80T-I/MM