PIC16F8X 18-pin Flash/EEPROM 8-Bit Microcontrollers Devices Included in this Data Sheet: Pin Diagrams • PIC16F83 PDIP, SOIC (cid:129) PIC16F84 (cid:129) PIC16CR83 RA2 1 18 RA1 (cid:129) PIC16CR84 RA3 2 17 RA0 (cid:129) Extended voltage range devices available RA4/T0CKI 3 PP 16 OSC1/CLKIN (PIC16LF8X, PIC16LCR8X) MCLR 4 ICIC 15 OSC2/CLKOUT 11 High Performance RISC CPU Features: VSS 5 6C6F 14 VDD RB0/INT 6 R8 13 RB7 (cid:129) Only 35 single word instructions to learn RB1 7 8XX 12 RB6 (cid:129) All instructions single cycle except for program RB2 8 11 RB5 branches which are two-cycle RB3 9 10 RB4 (cid:129) Operating speed: DC - 10 MHz clock input DC - 400 ns instruction cycle Special Microcontroller Features: Program Data Data Max. Device Memory RAM EEPROM Freq (cid:129) In-Circuit Serial Programming (ICSP™) - via two (words) (bytes) (bytes) (MHz) pins (ROM devices support only Data EEPROM PIC16F83 512 Flash 36 64 10 programming) PIC16F84 1 K Flash 68 64 10 (cid:129) Power-on Reset (POR) PIC16CR83 512 ROM 36 64 10 (cid:129) Power-up Timer (PWRT) PIC16CR84 1 K ROM 68 64 10 (cid:129) Oscillator Start-up Timer (OST) (cid:129) 14-bit wide instructions (cid:129) Watchdog Timer (WDT) with its own on-chip RC (cid:129) 8-bit wide data path oscillator for reliable operation (cid:129) 15 special function hardware registers (cid:129) Code-protection (cid:129) Eight-level deep hardware stack (cid:129) Power saving SLEEP mode (cid:129) Direct, indirect and relative addressing modes (cid:129) Selectable oscillator options (cid:129) Four interrupt sources: CMOS Flash/EEPROM Technology: - External RB0/INT pin (cid:129) Low-power, high-speed technology - TMR0 timer overflow (cid:129) Fully static design - PORTB<7:4> interrupt on change (cid:129) Wide operating voltage range: - Data EEPROM write complete - Commercial: 2.0V to 6.0V (cid:129) 1000 erase/write cycles Flash program memory - Industrial: 2.0V to 6.0V (cid:129) 10,000,000 erase/write cycles EEPROM data mem- (cid:129) Low power consumption: ory - < 2 mA typical @ 5V, 4 MHz (cid:129) EEPROM Data Retention > 40 years - 15 A typical @ 2V, 32 kHz Peripheral Features: - < 1 A typical standby current @ 2V (cid:129) 13 I/O pins with individual direction control (cid:129) High current sink/source for direct LED drive - 25 mA sink max. per pin - 20 mA source max. per pin (cid:129) TMR0: 8-bit timer/counter with 8-bit programmable prescaler  1996-2013 Microchip Technology Inc. DS30430D-page 1

PIC16F8X Table of Contents 1.0 General Description......................................................................................................................................................................3 2.0 PIC16F8X Device Varieties..........................................................................................................................................................5 3.0 Architectural Overview..................................................................................................................................................................7 4.0 Memory Organization.................................................................................................................................................................11 5.0 I/O Ports......................................................................................................................................................................................21 6.0 Timer0 Module and TMR0 Register............................................................................................................................................27 7.0 Data EEPROM Memory..............................................................................................................................................................33 8.0 Special Features of the CPU......................................................................................................................................................37 9.0 Instruction Set Summary............................................................................................................................................................53 10.0 Development Support.................................................................................................................................................................69 11.0 Electrical Characteristics for PIC16F83 and PIC16F84..............................................................................................................73 12.0 Electrical Characteristics for PIC16CR83 and PIC16CR84........................................................................................................85 13.0 DC & AC Characteristics Graphs/Tables....................................................................................................................................97 14.0 Packaging Information..............................................................................................................................................................109 Appendix A: Feature Improvements - From PIC16C5X To PIC16F8X..........................................................................................113 Appendix B: Code Compatibility - from PIC16C5X to PIC16F8X..................................................................................................113 Appendix C: What’s New In This Data Sheet.................................................................................................................................114 Appendix D: What’s Changed In This Data Sheet.........................................................................................................................114 Appendix E: Conversion Considerations - PIC16C84 to PIC16F83/F84 And PIC16CR83/CR84..................................................115 Index .................................................................................................................................................................................................117 On-Line Support.................................................................................................................................................................................119 Reader Response..............................................................................................................................................................................120 PIC16F8X Product Identification System...........................................................................................................................................121 Sales and Support..............................................................................................................................................................................121 To Our Valued Customers We constantly strive to improve the quality of all our products and documentation. We have spent a great deal of time to ensure that these documents are correct. However, we realize that we may have missed a few things. If you find any information that is missing or appears in error, please use the reader response form in the back of this data sheet to inform us. We appreciate your assistance in making this a better document. DS30430D-page 2  1996-2013 Microchip Technology Inc.

PIC16F8X 1.0 GENERAL DESCRIPTION Table1-1 lists the features of the PIC16F8X. A simpli- fied block diagram of the PIC16F8X is shown in The PIC16F8X is a group in the PIC16CXX family of Figure3-1. low-cost, high-performance, CMOS, fully-static, 8-bit microcontrollers. This group contains the following The PIC16F8X fits perfectly in applications ranging devices: from high speed automotive and appliance motor control to low-power remote sensors, electronic locks, (cid:129) PIC16F83 security devices and smart cards. The Flash/EEPROM (cid:129) PIC16F84 technology makes customization of application (cid:129) PIC16CR83 programs (transmitter codes, motor speeds, receiver (cid:129) PIC16CR84 frequencies, security codes, etc.) extremely fast and All PIC® microcontrollers employ an advanced RISC convenient. The small footprint packages make this microcontroller series perfect for all applications with architecture. PIC16F8X devices have enhanced core space limitations. Low-cost, low-power, high features, eight-level deep stack, and multiple internal performance, ease-of-use and I/O flexibility make the and external interrupt sources. The separate PIC16F8X very versatile even in areas where no instruction and data buses of the Harvard architecture microcontroller use has been considered before allow a 14-bit wide instruction word with a separate (e.g.,timer functions; serial communication; capture, 8-bit wide data bus. The two stage instruction pipeline compare and PWM functions; and co-processor allows all instructions to execute in a single cycle, applications). except for program branches (which require two cycles). A total of 35 instructions (reduced instruction The serial in-system programming feature (via two set) are available. Additionally, a large register set is pins) offers flexibility of customizing the product after used to achieve a very high performance level. complete assembly and testing. This feature can be used to serialize a product, store calibration data, or PIC16F8X microcontrollers typically achieve a 2:1 code program the device with the current firmware before compression and up to a 4:1 speed improvement (at 20 shipping. MHz) over other 8-bit microcontrollers in their class. The PIC16F8X has up to 68 bytes of RAM, 64 bytes of 1.1 Family and Upward Compatibility Data EEPROM memory, and 13 I/O pins. A timer/coun- ter is also available. Those users familiar with the PIC16C5X family of microcontrollers will realize that this is an enhanced The PIC16CXX family has special features to reduce version of the PIC16C5X architecture. Please refer to external components, thus reducing cost, enhancing AppendixA for a detailed list of enhancements. Code system reliability and reducing power consumption. written for PIC16C5X devices can be easily ported to There are four oscillator options, of which the single pin PIC16F8X devices (AppendixB). RC oscillator provides a low-cost solution, the LP oscillator minimizes power consumption, XT is a 1.2 Development Support standard crystal, and the HS is for High Speed crystals. The SLEEP (power-down) mode offers power saving. The PIC16CXX family is supported by a full-featured The user can wake the chip from sleep through several macro assembler, a software simulator, an in-circuit external and internal interrupts and resets. emulator, a low-cost development programmer and a full-featured programmer. A “C” compiler and fuzzy A highly reliable Watchdog Timer with its own on-chip logic support tools are also available. RC oscillator provides protection against software lock- up. The devices with Flash program memory allow the same device package to be used for prototyping and production. In-circuit reprogrammability allows the code to be updated without the device being removed from the end application. This is useful in the development of many applications where the device may not be easily accessible, but the prototypes may require code updates. This is also useful for remote applications where the code may need to be updated (such as rate information).  1996-2013 Microchip Technology Inc. DS30430D-page 3

PIC16F8X TABLE 1-1 PIC16F8X FAMILY OF DEVICES PIC16F83 PIC16CR83 PIC16F84 PIC16CR84 Maximum Frequency 10 10 10 10 Clock of Operation (MHz) Flash Program Memory 512 — 1K — EEPROM Program Memory — — — — Memory ROM Program Memory — 512 — 1K Data Memory (bytes) 36 36 68 68 Data EEPROM (bytes) 64 64 64 64 Peripherals Timer Module(s) TMR0 TMR0 TMR0 TMR0 Interrupt Sources 4 4 4 4 I/O Pins 13 13 13 13 Features Voltage Range (Volts) 2.0-6.0 2.0-6.0 2.0-6.0 2.0-6.0 Packages 18-pin DIP, 18-pin DIP, 18-pin DIP, 18-pin DIP, SOIC SOIC SOIC SOIC All PIC® Family devices have Power-on Reset, selectable Watchdog Timer, selectable code protect and high I/O current capability. All PIC16F8X Family devices use serial programming with clock pin RB6 and data pin RB7. DS30430D-page 4  1996-2013 Microchip Technology Inc.

PIC16F8X 2.0 PIC16F8X DEVICE VARIETIES 2.3 Serialized Quick-Turnaround- Production (SQTPSM ) Devices A variety of frequency ranges and packaging options are available. Depending on application and production Microchip offers the unique programming service requirements the proper device option can be selected where a few user-defined locations in each device are using the information in this section. When placing programmed with different serial numbers. The serial orders, please use the “PIC16F8X Product numbers may be random, pseudo-random Identification System” at the back of this data sheet to orsequential. specify the correct part number. Serial programming allows each device to have a There are four device “types” as indicated in the device unique number which can serve as an entry-code, number. password or ID number. 1. F, as in PIC16F84. These devices have Flash For information on submitting a SQTP code, please program memory and operate over the standard contact your Microchip Regional Sales Office. voltage range. 2. LF, as in PIC16LF84. These devices have Flash 2.4 ROM Devices program memory and operate over an extended Some of Microchip’s devices have a corresponding voltage range. device where the program memory is a ROM. These 3. CR, as in PIC16CR83. These devices have devices give a cost savings over Microchip’s traditional ROM program memory and operate over the user programmed devices (EPROM, EEPROM). standard voltage range. ROM devices (PIC16CR8X) do not allow serialization 4. LCR, as in PIC16LCR84. These devices have information in the program memory space. The user ROM program memory and operate over an may program this information into the Data EEPROM. extended voltage range. For information on submitting a ROM code, please When discussing memory maps and other architectural contact your Microchip Regional Sales Office. features, the use of F and CR also implies the LF and LCR versions. 2.1 Flash Devices These devices are offered in the lower cost plastic package, even though the device can be erased and reprogrammed. This allows the same device to be used for prototype development and pilot programs as well as production. A further advantage of the electrically-erasable Flash version is that it can be erased and reprogrammed in- circuit, or by device programmers, such as Microchip's PICSTART® Plus or PRO MATE® II programmers. 2.2 Quick-Turnaround-Production (QTP) Devices Microchip offers a QTP Programming Service for factory production orders. This service is made available for users who choose not to program a medium to high quantity of units and whose code patterns have stabilized. The devices have all Flash locations and configuration options already pro- grammed by the factory. Certain code and prototype verification procedures do apply before production shipments are available. For information on submitting a QTP code, please contact your Microchip Regional Sales Office.  1996-2013 Microchip Technology Inc. DS30430D-page 5

PIC16F8X NOTES: DS30430D-page 6  1996-2013 Microchip Technology Inc.

PIC16F8X 3.0 ARCHITECTURAL OVERVIEW The high performance of the PIC16CXX family can be attributed to a number of architectural features commonly found in RISC microprocessors. To begin with, the PIC16CXX uses a Harvard architecture. This architecture has the program and data accessed from separate memories. So the device has a program memory bus and a data memory bus. This improves bandwidth over traditional von Neumann architecture where program and data are fetched from the same memory (accesses over the same bus). Separating program and data memory further allows instructions to be sized differently than the 8-bit wide data word. PIC16CXX opcodes are 14-bits wide, enabling single word instructions. The full 14-bit wide program memory bus fetches a 14-bit instruction in a single cycle. A two- stage pipeline overlaps fetch and execution of instruc- tions (Example3-1). Consequently, all instructions exe- cute in a single cycle except for program branches. The PIC16F83 and PIC16CR83 address 512 x 14 of program memory, and the PIC16F84 and PIC16CR84 address 1K x 14 program memory. All program mem- ory is internal. The PIC16CXX can directly or indirectly address its register files or data memory. All special function registers including the program counter are mapped in the data memory. An orthogonal (symmetrical) instruction set makes it possible to carry out any oper- ation on any register using any addressing mode. This symmetrical nature and lack of ‘special optimal situations’ make programming with the PIC16CXX simple yet efficient. In addition, the learning curve is reduced significantly.  1996-2013 Microchip Technology Inc. DS30430D-page 7

PIC16F8X PIC16CXX devices contain an 8-bit ALU and working The W register is an 8-bit working register used for ALU register. The ALU is a general purpose arithmetic unit. operations. It is not an addressable register. It performs arithmetic and Boolean functions between Depending on the instruction executed, the ALU may data in the working register and any register file. affect the values of the Carry (C), Digit Carry (DC), and The ALU is 8-bits wide and capable of addition, Zero (Z) bits in the STATUS register. The C and DC bits subtraction, shift and logical operations. Unless operate as a borrow and digit borrow out bit, otherwise mentioned, arithmetic operations are two's respectively, in subtraction. See the SUBLW and SUBWF complement in nature. In two-operand instructions, instructions for examples. typically one operand is the working register A simplified block diagram for the PIC16F8X is shown (Wregister), and the other operand is a file register or in Figure3-1, its corresponding pin description is an immediate constant. In single operand instructions, shown in Table3-1. the operand is either the W register or a file register. FIGURE 3-1: PIC16F8X BLOCK DIAGRAM 13 Data Bus 8 Flash/ROM Program Counter EEPROM Data Memory Program Memory PIC16F83/CR83 RAM 512 x 14 File Registers EEPROM 8 Level Stack EEDATA Data Memory PIC16F84/CR84 PIC16F83/CR83 (13-bit) 64 x 8 1K x 14 36 x 8 PIC16F84/CR84 68 x 8 Program Bus 14 7 RAM Addr EEADR Addr Mux Instruction reg 5 Direct Addr 7 Indirect TMR0 Addr FSR reg RA4/T0CKI STATUS reg 8 MUX Power-up I/O Ports Timer 8 Instruction Oscillator Decode & Start-up Timer Control ALU Power-on RA3:RA0 Reset Timing Watchdog W reg RB7:RB1 Generation Timer RB0/INT OSC2/CLKOUT MCLR VDD, VSS OSC1/CLKIN DS30430D-page 8  1996-2013 Microchip Technology Inc.

PIC16F8X TABLE 3-1 PIC16F8X PINOUT DESCRIPTION DIP SOIC I/O/P Buffer Pin Name Description No. No. Type Type OSC1/CLKIN 16 16 I ST/CMOS (3) Oscillator crystal input/external clock source input. OSC2/CLKOUT 15 15 O — Oscillator crystal output. Connects to crystal or resonator in crystal oscillator mode. In RC mode, OSC2 pin outputs CLKOUT which has 1/4 the frequency of OSC1, and denotes the instruction cycle rate. MCLR 4 4 I/P ST Master clear (reset) input/programming voltage input. This pin is an active low reset to the device. PORTA is a bi-directional I/O port. RA0 17 17 I/O TTL RA1 18 18 I/O TTL RA2 1 1 I/O TTL RA3 2 2 I/O TTL RA4/T0CKI 3 3 I/O ST Can also be selected to be the clock input to the TMR0 timer/ counter. Output is open drain type. PORTB is a bi-directional I/O port. PORTB can be software pro- grammed for internal weak pull-up on all inputs. RB0/INT 6 6 I/O TTL/ST (1) RB0/INT can also be selected as an external interrupt pin. RB1 7 7 I/O TTL RB2 8 8 I/O TTL RB3 9 9 I/O TTL RB4 10 10 I/O TTL Interrupt on change pin. RB5 11 11 I/O TTL Interrupt on change pin. RB6 12 12 I/O TTL/ST (2) Interrupt on change pin. Serial programming clock. RB7 13 13 I/O TTL/ST (2) Interrupt on change pin. Serial programming data. VSS 5 5 P — Ground reference for logic and I/O pins. VDD 14 14 P — Positive supply for logic and I/O pins. Legend: I= input O = output I/O = Input/Output P = power — = Not used TTL = TTL input ST = Schmitt Trigger input Note 1: This buffer is a Schmitt Trigger input when configured as the external interrupt. 2: This buffer is a Schmitt Trigger input when used in serial programming mode. 3: This buffer is a Schmitt Trigger input when configured in RC oscillator mode and a CMOS input otherwise.  1996-2013 Microchip Technology Inc. DS30430D-page 9

PIC16F8X 3.1 Clocking Scheme/Instruction Cycle 3.2 Instruction Flow/Pipelining The clock input (from OSC1) is internally divided by An “Instruction Cycle” consists of four Q cycles (Q1, four to generate four non-overlapping quadrature Q2, Q3 and Q4). The instruction fetch and execute are clocks namely Q1, Q2, Q3 and Q4. Internally, the pipelined such that fetch takes one instruction cycle program counter (PC) is incremented every Q1, the while decode and execute takes another instruction instruction is fetched from the program memory and cycle. However, due to the pipelining, each instruction latched into the instruction register in Q4. The effectively executes in one cycle. If an instruction instruction is decoded and executed during the causes the program counter to change (e.g., GOTO) following Q1 through Q4. The clocks and instruction then two cycles are required to complete the instruction execution flow is shown in Figure3-2. (Example3-1). A fetch cycle begins with the Program Counter (PC) incrementing in Q1. In the execution cycle, the fetched instruction is latched into the “Instruction Register” in cycle Q1. This instruction is then decoded and executed during the Q2, Q3, and Q4 cycles. Data memory is read during Q2 (operand read) and written during Q4 (destination write). FIGURE 3-2: CLOCK/INSTRUCTION CYCLE Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 OSC1 Q1 Q2 Internal phase Q3 clock Q4 PC PC PC+1 PC+2 OSC2/CLKOUT (RC mode) Fetch INST (PC) Execute INST (PC-1) Fetch INST (PC+1) Execute INST (PC) Fetch INST (PC+2) Execute INST (PC+1) EXAMPLE 3-1: INSTRUCTION PIPELINE FLOW 1. MOVLW 55h Fetch 1 Execute 1 2. MOVWF PORTB Fetch 2 Execute 2 3. CALL SUB_1 Fetch 3 Execute 3 4. BSF PORTA, BIT3 Fetch 4 Flush Fetch SUB_1 Execute SUB_1 All instructions are single cycle, except for any program branches. These take two cycles since the fetch instruction is “flushed” from the pipeline while the new instruction is being fetched and then executed. DS30430D-page 10  1996-2013 Microchip Technology Inc.

PIC16F8X 4.0 MEMORY ORGANIZATION FIGURE 4-1: PROGRAM MEMORY MAP AND STACK - PIC16F83/CR83 There are two memory blocks in the PIC16F8X. These are the program memory and the data memory. Each PC<12:0> block has its own bus, so that access to each block can CALL, RETURN 13 occur during the same oscillator cycle. RETFIE, RETLW The data memory can further be broken down into the Stack Level 1  general purpose RAM and the Special Function   Registers (SFRs). The operation of the SFRs that Stack Level 8 control the “core” are described here. The SFRs used to control the peripheral modules are described in the Reset Vector 0000h section discussing each individual peripheral module. y Peripheral Interrupt Vector 0004h The data memory area also contains the data or me EEPROM memory. This memory is not directly mapped Meac p into the data memory, but is indirectly mapped. That is, er S an indirect address pointer specifies the address of the Us data EEPROM memory to read/write. The 64 bytes of data EEPROM memory have the address range 1FFh 0h-3Fh. More details on the EEPROM memory can be found in Section7.0. 4.1 Program Memory Organization The PIC16FXX has a 13-bit program counter capable 1FFFh of addressing an 8K x 14 program memory space. For the PIC16F83 and PIC16CR83, the first 512 x 14 (0000h-01FFh) are physically implemented FIGURE 4-2: PROGRAM MEMORY MAP (Figure4-1). For the PIC16F84 and PIC16CR84, the AND STACK - PIC16F84/CR84 first 1K x 14 (0000h-03FFh) are physically imple- mented (Figure4-2). Accessing a location above the PC<12:0> physically implemented address will cause a wrap- CALL, RETURN 13 around. For example, for the PIC16F84 locations 20h, RETFIE, RETLW 420h, 820h, C20h, 1020h, 1420h, 1820h, and 1C20h Stack Level 1 will be the same instruction.   The reset vector is at 0000h and the interrupt vector is Stack Level 8 at 0004h. Reset Vector 0000h Peripheral Interrupt Vector 0004h y or me ec Ma p er S s U 3FFh 1FFFh  1996-2013 Microchip Technology Inc. DS30430D-page 11

PIC16F8X 4.2 Data Memory Organization 4.2.1 GENERAL PURPOSE REGISTER FILE The data memory is partitioned into two areas. The first All devices have some amount of General Purpose is the Special Function Registers (SFR) area, while the Register (GPR) area. Each GPR is 8 bits wide and is second is the General Purpose Registers (GPR) area. accessed either directly or indirectly through the FSR The SFRs control the operation of the device. (Section4.5). Portions of data memory are banked. This is for both The GPR addresses in bank 1 are mapped to the SFR area and the GPR area. The GPR area is addresses in bank 0. As an example, addressing loca- banked to allow greater than 116 bytes of general tion 0Ch or 8Ch will access the same GPR. purpose RAM. The banked areas of the SFR are for the 4.2.2 SPECIAL FUNCTION REGISTERS registers that control the peripheral functions. Banking requires the use of control bits for bank selection. The Special Function Registers (Figure4-1, Figure4-2 These control bits are located in the STATUS Register. and Table4-1) are used by the CPU and Peripheral Figure4-1 and Figure4-2 show the data memory map functions to control the device operation. These organization. registers are static RAM. Instructions MOVWF and MOVF can move values from The special function registers can be classified into two the W register to any location in the register file (“F”), sets, core and peripheral. Those associated with the and vice-versa. core functions are described in this section. Those The entire data memory can be accessed either related to the operation of the peripheral features are directly using the absolute address of each register file described in the section for that specific feature. or indirectly through the File Select Register (FSR) (Section4.5). Indirect addressing uses the present value of the RP1:RP0 bits for access into the banked areas of data memory. Data memory is partitioned into two banks which contain the general purpose registers and the special function registers. Bank 0 is selected by clearing the RP0 bit (STATUS<5>). Setting the RP0 bit selects Bank 1. Each Bank extends up to 7Fh (128 bytes). The first twelve locations of each Bank are reserved for the Special Function Registers. The remainder are Gen- eral Purpose Registers implemented as static RAM. DS30430D-page 12  1996-2013 Microchip Technology Inc.

PIC16F8X FIGURE 4-1: REGISTER FILE MAP - FIGURE 4-2: REGISTER FILE MAP - PIC16F83/CR83 PIC16F84/CR84 File Address File Address File Address File Address 00h Indirect addr.(1) Indirect addr.(1) 80h 00h Indirect addr.(1) Indirect addr.(1) 80h 01h TMR0 OPTION 81h 01h TMR0 OPTION 81h 02h PCL PCL 82h 02h PCL PCL 82h 03h STATUS STATUS 83h 03h STATUS STATUS 83h 04h FSR FSR 84h 04h FSR FSR 84h 05h PORTA TRISA 85h 05h PORTA TRISA 85h 06h PORTB TRISB 86h 06h PORTB TRISB 86h 07h 87h 07h 87h 08h EEDATA EECON1 88h 08h EEDATA EECON1 88h 09h EEADR EECON2(1) 89h 09h EEADR EECON2(1) 89h 0Ah PCLATH PCLATH 8Ah 0Ah PCLATH PCLATH 8Ah 0Bh INTCON INTCON 8Bh 0Bh INTCON INTCON 8Bh 0Ch 8Ch 0Ch 8Ch 36 General Mapped Purpose (accesses) registers in Bank 0 68 (SRAM) General Mapped Purpose (accesses) 2Fh AFh registers in Bank 0 (SRAM) 30h B0h 4Fh CFh 50h D0h 7Fh FFh 7Fh FFh Bank 0 Bank 1 Bank 0 Bank 1 Unimplemented data memory location; read as '0'. Unimplemented data memory location; read as '0'. Note 1: Not a physical register. Note 1: Not a physical register.  1996-2013 Microchip Technology Inc. DS30430D-page 13

PIC16F8X TABLE 4-1 REGISTER FILE SUMMARY Value on Value on all Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Power-on other resets Reset (Note3) Bank 0 00h INDF Uses contents of FSR to address data memory (not a physical register) ---- ---- ---- ---- 01h TMR0 8-bit real-time clock/counter xxxx xxxx uuuu uuuu 02h PCL Low order 8 bits of the Program Counter (PC) 0000 0000 0000 0000 03h STATUS (2) IRP RP1 RP0 TO PD Z DC C 0001 1xxx 000q quuu 04h FSR Indirect data memory address pointer 0 xxxx xxxx uuuu uuuu 05h PORTA — — — RA4/T0CKI RA3 RA2 RA1 RA0 ---x xxxx ---u uuuu 06h PORTB RB7 RB6 RB5 RB4 RB3 RB2 RB1 RB0/INT xxxx xxxx uuuu uuuu 07h Unimplemented location, read as '0' ---- ---- ---- ---- 08h EEDATA EEPROM data register xxxx xxxx uuuu uuuu 09h EEADR EEPROM address register xxxx xxxx uuuu uuuu 0Ah PCLATH — — — Write buffer for upper 5 bits of the PC (1) ---0 0000 ---0 0000 0Bh INTCON GIE EEIE T0IE INTE RBIE T0IF INTF RBIF 0000 000x 0000 000u Bank 1 80h INDF Uses contents of FSR to address data memory (not a physical register) ---- ---- ---- ---- OPTION_ 1111 1111 1111 1111 81h RBPU INTEDG T0CS T0SE PSA PS2 PS1 PS0 REG 82h PCL Low order 8 bits of Program Counter (PC) 0000 0000 0000 0000 83h STATUS (2) IRP RP1 RP0 TO PD Z DC C 0001 1xxx 000q quuu 84h FSR Indirect data memory address pointer 0 xxxx xxxx uuuu uuuu 85h TRISA — — — PORTA data direction register ---1 1111 ---1 1111 86h TRISB PORTB data direction register 1111 1111 1111 1111 87h Unimplemented location, read as '0' ---- ---- ---- ---- 88h EECON1 — — — EEIF WRERR WREN WR RD ---0 x000 ---0 q000 89h EECON2 EEPROM control register 2 (not a physical register) ---- ---- ---- ---- 0Ah PCLATH — — — Write buffer for upper 5 bits of the PC (1) ---0 0000 ---0 0000 0Bh INTCON GIE EEIE T0IE INTE RBIE T0IF INTF RBIF 0000 000x 0000 000u Legend: x = unknown, u = unchanged. - = unimplemented read as '0', q = value depends on condition. Note 1: The upper byte of the program counter is not directly accessible. PCLATH is a slave register for PC<12:8>. The contents of PCLATH can be transferred to the upper byte of the program counter, but the contents of PC<12:8> is never transferred to PCLATH. 2: The TO and PD status bits in the STATUS register are not affected by a MCLR reset. 3: Other (non power-up) resets include: external reset through MCLR and the Watchdog Timer Reset. DS30430D-page 14  1996-2013 Microchip Technology Inc.

PIC16F8X 4.2.2.1 STATUS REGISTER Only the BCF, BSF, SWAPF and MOVWF instructions should be used to alter the STATUS register (Table9-2) The STATUS register contains the arithmetic status of because these instructions do not affect any status bit. the ALU, the RESET status and the bank select bit for data memory. Note 1: The IRP and RP1 bits (STATUS<7:6>) are not used by the PIC16F8X and should be As with any register, the STATUS register can be the programmed as cleared. Use of these bits destination for any instruction. If the STATUS register is as general purpose R/W bits is NOT the destination for an instruction that affects the Z, DC recommended, since this may affect or C bits, then the write to these three bits is disabled. upward compatibility with future products. These bits are set or cleared according to device logic. Furthermore, the TO and PD bits are not writable. Note 2: The C and DC bits operate as a borrow Therefore, the result of an instruction with the STATUS and digit borrow out bit, respectively, in register as destination may be different than intended. subtraction. See the SUBLW and SUBWF instructions for examples. For example, CLRF STATUS will clear the upper-three bits and set the Z bit. This leaves the STATUS register Note 3: When the STATUS register is the as 000u u1uu (where u = unchanged). destination for an instruction that affects the Z, DC or C bits, then the write to these three bits is disabled. The specified bit(s) will be updated according to device logic FIGURE 4-1: STATUS REGISTER (ADDRESS 03h, 83h) R/W-0 R/W-0 R/W-0 R-1 R-1 R/W-x R/W-x R/W-x IRP RP1 RP0 TO PD Z DC C R = Readable bit bit7 bit0 W = Writable bit U = Unimplemented bit, read as ‘0’ - n = Value at POR reset bit 7: IRP: Register Bank Select bit (used for indirect addressing) 0 = Bank 0, 1 (00h - FFh) 1 = Bank 2, 3 (100h - 1FFh) The IRP bit is not used by the PIC16F8X. IRP should be maintained clear. bit 6-5: RP1:RP0: Register Bank Select bits (used for direct addressing) 00 = Bank 0 (00h - 7Fh) 01 = Bank 1 (80h - FFh) 10 = Bank 2 (100h - 17Fh) 11 = Bank 3 (180h - 1FFh) Each bank is 128 bytes. Only bit RP0 is used by the PIC16F8X. RP1 should be maintained clear. bit 4: TO: Time-out bit 1 = After power-up, CLRWDT instruction, or SLEEP instruction 0 = A WDT time-out occurred bit 3: PD: Power-down bit 1 = After power-up or by the CLRWDT instruction 0 = By execution of the SLEEP instruction bit 2: Z: Zero bit 1 = The result of an arithmetic or logic operation is zero 0 = The result of an arithmetic or logic operation is not zero bit 1: DC: Digit carry/borrow bit (for ADDWF and ADDLW instructions) (For borrow the polarity is reversed) 1 = A carry-out from the 4th low order bit of the result occurred 0 = No carry-out from the 4th low order bit of the result bit 0: C: Carry/borrow bit (for ADDWF and ADDLW instructions) 1 = A carry-out from the most significant bit of the result occurred 0 = No carry-out from the most significant bit of the result occurred Note:For borrow the polarity is reversed. A subtraction is executed by adding the two’s complement of the second operand. For rotate (RRF, RLF) instructions, this bit is loaded with either the high or low order bit of the source register.  1996-2013 Microchip Technology Inc. DS30430D-page 15

PIC16F8X 4.2.2.2 OPTION_REG REGISTER Note: When the prescaler is assigned to The OPTION_REG register is a readable and writable the WDT (PSA = '1'), TMR0 has a 1:1 register which contains various control bits to configure prescaler assignment. the TMR0/WDT prescaler, the external INT interrupt, TMR0, and the weak pull-ups on PORTB. FIGURE 4-1: OPTION_REG REGISTER (ADDRESS 81h) R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 RBPU INTEDG T0CS T0SE PSA PS2 PS1 PS0 R = Readable bit bit7 bit0 W = Writable bit U = Unimplemented bit, read as ‘0’ - n = Value at POR reset bit 7: RBPU: PORTB Pull-up Enable bit 1 = PORTB pull-ups are disabled 0 = PORTB pull-ups are enabled (by individual port latch values) bit 6: INTEDG: Interrupt Edge Select bit 1 = Interrupt on rising edge of RB0/INT pin 0 = Interrupt on falling edge of RB0/INT pin bit 5: T0CS: TMR0 Clock Source Select bit 1 = Transition on RA4/T0CKI pin 0 = Internal instruction cycle clock (CLKOUT) bit 4: T0SE: TMR0 Source Edge Select bit 1 = Increment on high-to-low transition on RA4/T0CKI pin 0 = Increment on low-to-high transition on RA4/T0CKI pin bit 3: PSA: Prescaler Assignment bit 1 = Prescaler assigned to the WDT 0 = Prescaler assigned to TMR0 bit 2-0: PS2:PS0: Prescaler Rate Select bits Bit Value TMR0 Rate WDT Rate 000 1 : 2 1 : 1 001 1 : 4 1 : 2 010 1 : 8 1 : 4 011 1 : 16 1 : 8 100 1 : 32 1 : 16 101 1 : 64 1 : 32 110 1 : 128 1 : 64 111 1 : 256 1 : 128 DS30430D-page 16  1996-2013 Microchip Technology Inc.

PIC16F8X 4.2.2.3 INTCON REGISTER Note: Interrupt flag bits get set when an interrupt The INTCON register is a readable and writable condition occurs regardless of the state of register which contains the various enable bits for all its corresponding enable bit or the global interrupt sources. enable bit, GIE (INTCON<7>). FIGURE 4-1: INTCON REGISTER (ADDRESS 0Bh, 8Bh) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-x GIE EEIE T0IE INTE RBIE T0IF INTF RBIF R = Readable bit bit7 bit0 W = Writable bit U = Unimplemented bit, read as ‘0’ - n = Value at POR reset bit 7: GIE: Global Interrupt Enable bit 1 = Enables all un-masked interrupts 0 = Disables all interrupts Note:For the operation of the interrupt structure, please refer to Section8.5. bit 6: EEIE: EE Write Complete Interrupt Enable bit 1 = Enables the EE write complete interrupt 0 = Disables the EE write complete interrupt bit 5: T0IE: TMR0 Overflow Interrupt Enable bit 1 = Enables the TMR0 interrupt 0 = Disables the TMR0 interrupt bit 4: INTE: RB0/INT Interrupt Enable bit 1 = Enables the RB0/INT interrupt 0 = Disables the RB0/INT interrupt bit 3: RBIE: RB Port Change Interrupt Enable bit 1 = Enables the RB port change interrupt 0 = Disables the RB port change interrupt bit 2: T0IF: TMR0 overflow interrupt flag bit 1 = TMR0 has overflowed (must be cleared in software) 0 = TMR0 did not overflow bit 1: INTF: RB0/INT Interrupt Flag bit 1 = The RB0/INT interrupt occurred 0 = The RB0/INT interrupt did not occur bit 0: RBIF: RB Port Change Interrupt Flag bit 1 = When at least one of the RB7:RB4 pins changed state (must be cleared in software) 0 = None of the RB7:RB4 pins have changed state  1996-2013 Microchip Technology Inc. DS30430D-page 17

PIC16F8X 4.3 Program Counter: PCL and PCLATH manipulation of the PCLATH<4:3> is not required for the return instructions (which “pops” the PC from the The Program Counter (PC) is 13-bits wide. The low stack). byte is the PCL register, which is a readable and writable register. The high byte of the PC (PC<12:8>) is Note: The PIC16F8X ignores the PCLATH<4:3> not directly readable nor writable and comes from the bits, which are used for program memory PCLATH register. The PCLATH (PC latch high) register pages 1, 2 and 3 (0800h - 1FFFh). The is a holding register for PC<12:8>. The contents of use of PCLATH<4:3> as general purpose PCLATH are transferred to the upper byte of the R/W bits is not recommended since this program counter when the PC is loaded with a new may affect upward compatibility with value. This occurs during a CALL, GOTO or a write to future products. PCL. The high bits of PC are loaded from PCLATH as 4.4 Stack shown in Figure4-1. The PIC16FXX has an 8 deep x 13-bit wide hardware FIGURE 4-1: LOADING OF PC IN stack (Figure4-1). The stack space is not part of either DIFFERENT SITUATIONS program or data space and the stack pointer is not readable or writable. PCH PCL 12 8 7 0 The entire 13-bit PC is “pushed” onto the stack when a PC INST with PCL CALL instruction is executed or an interrupt is acknowl- as dest edged. The stack is “popped” in the event of a PCLATH<4:0> 8 5 ALU result RETURN, RETLW or a RETFIE instruction execution. PCLATH is not affected by a push or a pop operation. PCLATH Note: There are no instruction mnemonics called push or pop. These are actions that PCH PCL 12 1110 8 7 0 occur from the execution of the CALL, RETURN, RETLW, and RETFIE instruc- PC GOTO, CALL tions, or the vectoring to an interrupt PCLATH<4:3> 11 2 Opcode <10:0> address. The stack operates as a circular buffer. That is, after the PCLATH stack has been pushed eight times, the ninth push over- writes the value that was stored from the first push. The 4.3.1 COMPUTED GOTO tenth push overwrites the second push (and so on). If the stack is effectively popped nine times, the PC A computed GOTO is accomplished by adding an offset value is the same as the value from the first pop. to the program counter (ADDWF PCL). When doing a table read using a computed GOTO method, care should Note: There are no status bits to indicate stack be exercised if the table location crosses a PCL memory overflow or stack underflow conditions. boundary (each 256 word block). Refer to the application note “Implementing a Table Read” (AN556). 4.3.2 PROGRAM MEMORY PAGING The PIC16F83 and PIC16CR83 have 512 words of pro- gram memory. The PIC16F84 and PIC16CR84 have 1K of program memory. The CALL and GOTO instruc- tions have an 11-bit address range. This 11-bit address range allows a branch within a 2K program memory page size. For future PIC16F8X program memory expansion, there must be another two bits to specify the program memory page. These paging bits come from the PCLATH<4:3> bits (Figure4-1). When doing a CALL or a GOTO instruction, the user must ensure that these page bits (PCLATH<4:3>) are programmed to the desired program memory page. If a CALL instruc- tion (or interrupt) is executed, the entire 13-bit PC is “pushed” onto the stack (see next section). Therefore, DS30430D-page 18  1996-2013 Microchip Technology Inc.

PIC16F8X 4.5 Indirect Addressing; INDF and FSR A simple program to clear RAM locations 20h-2Fh Registers using indirect addressing is shown in Example4-2. The INDF register is not a physical register. Address- EXAMPLE 4-2: HOW TO CLEAR RAM ing INDF actually addresses the register whose USING INDIRECT address is contained in the FSR register (FSR is a ADDRESSING pointer). This is indirect addressing. movlw 0x20 ;initialize pointer movwf FSR ; to RAM EXAMPLE 4-1: INDIRECT ADDRESSING NEXT clrf INDF ;clear INDF register (cid:129) Register file 05 contains the value 10h incf FSR ;inc pointer (cid:129) Register file 06 contains the value 0Ah btfss FSR,4 ;all done? (cid:129) Load the value 05 into the FSR register goto NEXT ;NO, clear next CONTINUE (cid:129) A read of the INDF register will return the value of : ;YES, continue 10h (cid:129) Increment the value of the FSR register by one An effective 9-bit address is obtained by concatenating (FSR = 06) the 8-bit FSR register and the IRP bit (STATUS<7>), as (cid:129) A read of the INDF register now will return the shown in Figure4-1. However, IRP is not used in the value of 0Ah. PIC16F8X. Reading INDF itself indirectly (FSR = 0) will produce 00h. Writing to the INDF register indirectly results in a no-operation (although STATUS bits may be affected). FIGURE 4-1: DIRECT/INDIRECT ADDRESSING Direct Addressing Indirect Addressing RP1RP0 6 from opcode 0 IRP 7 (FSR) 0 bank select location select bank select location select 00 01 10 11 00h 00h not used not used 0Bh 0Ch Addresses Data 2Fh (1) map back Memory (3) 30h (1) to Bank 0 4Fh (2) 50h (2) 7Fh 7Fh Bank 0 Bank 1 Bank 2 Bank 3 Note 1: PIC16F83 and PIC16CR83 devices. 2: PIC16F84 and PIC16CR84 devices 3: For memory map detail see Figure4-1.  1996-2013 Microchip Technology Inc. DS30430D-page 19

PIC16F8X NOTES: DS30430D-page 20  1996-2013 Microchip Technology Inc.

PIC16F8X 5.0 I/O PORTS EXAMPLE 5-1: INITIALIZING PORTA CLRF PORTA ; Initialize PORTA by The PIC16F8X has two ports, PORTA and PORTB. ; setting output Some port pins are multiplexed with an alternate func- ; data latches tion for other features on the device. BSF STATUS, RP0 ; Select Bank 1 MOVLW 0x0F ; Value used to 5.1 PORTA and TRISA Registers ; initialize data ; direction PORTA is a 5-bit wide latch. RA4 is a Schmitt Trigger MOVWF TRISA ; Set RA<3:0> as inputs input and an open drain output. All other RA port pins ; RA4 as outputs have TTL input levels and full CMOS output drivers. All ; TRISA<7:5> are always pins have data direction bits (TRIS registers) which can ; read as '0'. configure these pins as output or input. FIGURE 5-2: BLOCK DIAGRAM OF PIN RA4 Setting a TRISA bit (=1) will make the corresponding PORTA pin an input, i.e., put the corresponding output driver in a hi-impedance mode. Clearing a TRISA bit Data (=0) will make the corresponding PORTA pin an output, bus D Q i.e., put the contents of the output latch on the selected WR pin. PORT CK Q RA4 pin N Reading the PORTA register reads the status of the pins Data Latch whereas writing to it will write to the port latch. All write operations are read-modify-write operations. So a write VSS D Q to a port implies that the port pins are first read, then this value is modified and written to the port data latch. WR TRIS CK Q The RA4 pin is multiplexed with the TMR0 clock input. Schmitt TRIS Latch Trigger input FIGURE 5-1: BLOCK DIAGRAM OF PINS buffer RA3:RA0 Data RD TRIS bus D Q VDD Q D WR Port CK Q EENN P RD PORT Data Latch N I/O pin TMR0 clock input D Q WR VSS Note: I/O pin has protection diodes to VSS only. TRIS CK Q TRIS Latch TTL input buffer RD TRIS Q D EN RD PORT Note: I/O pins have protection diodes to VDD and VSS.  1996-2013 Microchip Technology Inc. DS30430D-page 21

PIC16F8X TABLE 5-1 PORTA FUNCTIONS Name Bit0 Buffer Type Function RA0 bit0 TTL Input/output RA1 bit1 TTL Input/output RA2 bit2 TTL Input/output RA3 bit3 TTL Input/output RA4/T0CKI bit4 ST Input/output or external clock input for TMR0. Output is open drain type. Legend: TTL = TTL input, ST = Schmitt Trigger input TABLE 5-2 SUMMARY OF REGISTERS ASSOCIATED WITH PORTA Value on Value on all Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Power-on other resets Reset 05h PORTA — — — RA4/T0CKI RA3 RA2 RA1 RA0 ---x xxxx ---u uuuu 85h TRISA — — — TRISA4 TRISA3 TRISA2 TRISA1 TRISA0 ---1 1111 ---1 1111 Legend: x = unknown, u = unchanged, - = unimplemented read as '0'. Shaded cells are unimplemented, read as '0' DS30430D-page 22  1996-2013 Microchip Technology Inc.

PIC16F8X 5.2 PORTB and TRISB Registers This interrupt can wake the device from SLEEP. The user, in the interrupt service routine, can clear the PORTB is an 8-bit wide bi-directional port. The interrupt in the following manner: corresponding data direction register is TRISB. A '1' on a) Read (or write) PORTB. This will end the mis- any bit in the TRISB register puts the corresponding match condition. output driver in a hi-impedance mode. A '0' on any bit in the TRISB register puts the contents of the output b) Clear flag bit RBIF. latch on the selected pin(s). A mismatch condition will continue to set the RBIF bit. Each of the PORTB pins have a weak internal pull-up. Reading PORTB will end the mismatch condition, and allow the RBIF bit to be cleared. A single control bit can turn on all the pull-ups. This is done by clearing the RBPU (OPTION_REG<7>) bit. This interrupt on mismatch feature, together with The weak pull-up is automatically turned off when the software configurable pull-ups on these four pins allow port pin is configured as an output. The pull-ups are easy interface to a key pad and make it possible for disabled on a Power-on Reset. wake-up on key-depression (see AN552 in the Four of PORTB’s pins, RB7:RB4, have an interrupt on Embedded Control Handbook). change feature. Only pins configured as inputs can Note 1: For a change on the I/O pin to be cause this interrupt to occur (i.e., any RB7:RB4 pin recognized, the pulse width must be at configured as an output is excluded from the interrupt least TCY (4/fOSC) wide. on change comparison). The pins value in input mode The interrupt on change feature is recommended for are compared with the old value latched on the last wake-up on key depression operation and operations read of PORTB. The “mismatch” outputs of the pins are where PORTB is only used for the interrupt on change OR’ed together to generate the RB port feature. Polling of PORTB is not recommended while changeinterrupt. using the interrupt on change feature. FIGURE 5-3: BLOCK DIAGRAM OF PINS FIGURE 5-4: BLOCK DIAGRAM OF PINS RB7:RB4 RB3:RB0 VDD VDD RBPU(1) weak P RBPU(1) pull-up weak P pull-up Data bus Data Latch Data Latch D Q Data bus D Q I/O I/O WR Port CK pin(2) WR Port CK pin(2) TRIS Latch D Q TRIS Latch TTL Input D Q WR TRIS CK Buffer WR TRIS CK TTL Input Buffer RD TRIS RD TRIS Latch Q D Q D RD Port EN RD Port EN Set RBIF RB0/INT Schmitt Trigger From other Q D Buffer RD Port RB7:RB4 pins Note 1: TRISB = '1' enables weak pull-up EN (if RBPU = '0' in the OPTION_REG register). 2: I/O pins have diode protection to VDD and VSS. RD Port Note 1: TRISB = '1' enables weak pull-up (if RBPU = '0' in the OPTION_REG register). 2: I/O pins have diode protection to VDD and VSS.  1996-2013 Microchip Technology Inc. DS30430D-page 23

PIC16F8X EXAMPLE 5-1: INITIALIZING PORTB CLRF PORTB ; Initialize PORTB by ; setting output ; data latches BSF STATUS, RP0 ; Select Bank 1 MOVLW 0xCF ; Value used to ; initialize data ; direction MOVWF TRISB ; Set RB<3:0> as inputs ; RB<5:4> as outputs ; RB<7:6> as inputs TABLE 5-3 PORTB FUNCTIONS Name Bit Buffer Type I/O Consistency Function RB0/INT bit0 TTL/ST(1) Input/output pin or external interrupt input. Internal software programmable weak pull-up. RB1 bit1 TTL Input/output pin. Internal software programmable weak pull-up. RB2 bit2 TTL Input/output pin. Internal software programmable weak pull-up. RB3 bit3 TTL Input/output pin. Internal software programmable weak pull-up. RB4 bit4 TTL Input/output pin (with interrupt on change). Internal software programmable weak pull-up. RB5 bit5 TTL Input/output pin (with interrupt on change). Internal software programmable weak pull-up. RB6 bit6 TTL/ST(2) Input/output pin (with interrupt on change). Internal software programmable weak pull-up. Serial programming clock. RB7 bit7 TTL/ST(2) Input/output pin (with interrupt on change). Internal software programmable weak pull-up. Serial programming data. Legend: TTL = TTL input, ST = Schmitt Trigger. Note1: This buffer is a Schmitt Trigger input when configured as the external interrupt. 2: This buffer is a Schmitt Trigger input when used in serial programming mode. TABLE 5-4 SUMMARY OF REGISTERS ASSOCIATED WITH PORTB Value on Value on all Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Power-on other resets Reset 06h PORTB RB7 RB6 RB5 RB4 RB3 RB2 RB1 RB0/INT xxxx xxxx uuuu uuuu 86h TRISB TRISB7 TRISB6 TRISB5 TRISB4 TRISB3 TRISB2 TRISB1 TRISB0 1111 1111 1111 1111 OPTION_ 1111 1111 1111 1111 81h RBPU INTEDG T0CS T0SE PSA PS2 PS1 PS0 REG Legend: x = unknown, u = unchanged. Shaded cells are not used by PORTB. DS30430D-page 24  1996-2013 Microchip Technology Inc.

PIC16F8X 5.3 I/O Programming Considerations 5.3.2 SUCCESSIVE OPERATIONS ON I/O PORTS 5.3.1 BI-DIRECTIONAL I/O PORTS The actual write to an I/O port happens at the end of an Any instruction which writes, operates internally as a instruction cycle, whereas for reading, the data must be read followed by a write operation. The BCF and BSF valid at the beginning of the instruction cycle instructions, for example, read the register into the (Figure5-5). Therefore, care must be exercised if a CPU, execute the bit operation and write the result back write followed by a read operation is carried out on the to the register. Caution must be used when these same I/O port. The sequence of instructions should be instructions are applied to a port with both inputs and such that the pin voltage stabilizes (load dependent) outputs defined. For example, a BSF operation on bit5 before the next instruction which causes that file to be of PORTB will cause all eight bits of PORTB to be read read into the CPU is executed. Otherwise, the previous into the CPU. Then the BSF operation takes place on state of that pin may be read into the CPU rather than bit5 and PORTB is written to the output latches. If the new state. When in doubt, it is better to separate another bit of PORTB is used as a bi-directional I/O pin these instructions with a NOP or another instruction not (i.e., bit0) and it is defined as an input at this time, the accessing this I/O port. input signal present on the pin itself would be read into Example5-1 shows the effect of two sequential the CPU and rewritten to the data latch of this particular read-modify-write instructions (e.g., BCF, BSF, etc.) on pin, overwriting the previous content. As long as the pin an I/O port. stays in the input mode, no problem occurs. However, if bit0 is switched into output mode later on, the content EXAMPLE 5-1: READ-MODIFY-WRITE of the data latch is unknown. INSTRUCTIONS ON AN Reading the port register, reads the values of the port I/OPORT pins. Writing to the port register writes the value to the ;Initial PORT settings: PORTB<7:4> Inputs port latch. When using read-modify-write instructions ; PORTB<3:0> Outputs (i.e., BCF, BSF, etc.) on a port, the value of the port ;PORTB<7:6> have external pull-ups and are pins is read, the desired operation is done to this value, ;not connected to other circuitry and this value is then written to the port latch. ; ; PORT latch PORT pins A pin actively outputting a Low or High should not be ; ---------- --------- driven from external devices at the same time in order BCF PORTB, 7 ; 01pp ppp 11pp ppp to change the level on this pin (“wired-or”, “wired-and”). BCF PORTB, 6 ; 10pp ppp 11pp ppp The resulting high output current may damage the chip. BSF STATUS, RP0 ; BCF TRISB, 7 ; 10pp ppp 11pp ppp BCF TRISB, 6 ; 10pp ppp 10pp ppp ; ;Note that the user may have expected the ;pin values to be 00pp ppp. The 2nd BCF ;caused RB7 to be latched as the pin value ;(high). FIGURE 5-5: SUCCESSIVE I/O OPERATION Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Note: PC PC PC + 1 PC + 2 PC + 3 This example shows a write to PORTB Instruction followed by a read from PORTB. fetched MOVWF PORTB MOVF PORTB,W write to NOP NOP Note that: PORTB RB7:RB0 data setup time = (0.25TCY - TPD) where TCY = instruction cycle Port pin sampled here TPD = propagation delay Instruction TPD Therefore, at higher clock frequencies, executed NOP a write followed by a read may be prob- MOVWF PORTB MOVF PORTB,W lematic. write to PORTB  1996-2013 Microchip Technology Inc. DS30430D-page 25

PIC16F8X NOTES: DS30430D-page 26  1996-2013 Microchip Technology Inc.

PIC16F8X 6.0 TIMER0 MODULE AND TMR0 edge select bit, T0SE (OPTION_REG<4>). Clearing bit REGISTER T0SE selects the rising edge. Restrictions on the exter- nal clock input are discussed in detail in Section6.2. The Timer0 module timer/counter has the following The prescaler is shared between the Timer0 Module features: and the Watchdog Timer. The prescaler assignment is (cid:129) 8-bit timer/counter controlled, in software, by control bit PSA (cid:129) Readable and writable (OPTION_REG<3>). Clearing bit PSA will assign the (cid:129) 8-bit software programmable prescaler prescaler to the Timer0 Module. The prescaler is not readable or writable. When the prescaler (Section6.3) (cid:129) Internal or external clock select is assigned to the Timer0 Module, the prescale value (cid:129) Interrupt on overflow from FFh to 00h (1:2, 1:4, ..., 1:256) is software selectable. (cid:129) Edge select for external clock 6.1 TMR0 Interrupt Timer mode is selected by clearing the T0CS bit (OPTION_REG<5>). In timer mode, the Timer0 mod- The TMR0 interrupt is generated when the TMR0 ule (Figure6-1) will increment every instruction cycle register overflows from FFh to 00h. This overflow sets (without prescaler). If the TMR0 register is written, the the T0IF bit (INTCON<2>). The interrupt can be increment is inhibited for the following two cycles masked by clearing enable bit T0IE (INTCON<5>). The (Figure6-2 and Figure6-3). The user can work around T0IF bit must be cleared in software by the Timer0 this by writing an adjusted value to the TMR0 register. Module interrupt service routine before re-enabling this Counter mode is selected by setting the T0CS bit interrupt. The TMR0 interrupt (Figure6-4) cannot wake (OPTION_REG<5>). In this mode TMR0 will increment the processor from SLEEP since the timer is shut off either on every rising or falling edge of pin RA4/T0CKI. during SLEEP. The incrementing edge is determined by the T0 source FIGURE 6-1: TMR0 BLOCK DIAGRAM Data bus FOSC/4 0 PSout 8 1 Sync with 1 Internal TMR0 register clocks RA4/T0CKI Programmable 0 PSout pin Prescaler T0SE (2 cycle delay) 3 Set bit T0IF PS2, PS1, PS0 PSA on Overflow T0CS Note 1: Bits T0CS, T0SE, PS2, PS1, PS0 and PSA are located in the OPTION_REG register. 2: The prescaler is shared with the Watchdog Timer (Figure6-6) FIGURE 6-2: TMR0 TIMING: INTERNAL CLOCK/NO PRESCALER Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 PC PC-1 PC PC+1 PC+2 PC+3 PC+4 PC+5 PC+6 Instruction MOVWF TMR0 MOVF TMR0,W MOVF TMR0,W MOVF TMR0,W MOVF TMR0,W MOVF TMR0,W Fetch TMR0 T0 T0+1 T0+2 NT0 NT0 NT0 NT0+1 NT0+2 T0 Instruction Executed Write TMR0 Read TMR0 Read TMR0 Read TMR0 Read TMR0 Read TMR0 executed reads NT0 reads NT0 reads NT0 reads NT0 + 1 reads NT0 + 2  1996-2013 Microchip Technology Inc. DS30430D-page 27

PIC16F8X FIGURE 6-3: TMR0 TIMING: INTERNAL CLOCK/PRESCALE 1:2 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 PC PC-1 PC PC+1 PC+2 PC+3 PC+4 PC+5 PC+6 Instruction MOVWF TMR0 MOVF TMR0,W MOVF TMR0,W MOVF TMR0,W MOVF TMR0,W MOVF TMR0,W Fetch TMR0 T0 T0+1 NT0 NT0+1 Instruction Execute Write TMR0 Read TMR0 Read TMR0 Read TMR0 Read TMR0 Read TMR0 executed reads NT0 reads NT0 reads NT0 reads NT0 reads NT0 + 1 FIGURE 6-4: TMR0 INTERRUPT TIMING Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 OSC1 CLKOUT(3) TMR0 timer FEh FFh 00h 01h 02h 1 1 T0IF bit 4 (INTCON<2>) GIE bit (INTCON<7>) Interrupt Latency(2) INSTRUCTION FLOW PC PC PC +1 PC +1 0004h 0005h Instruction fetched Inst (PC) Inst (PC+1) Inst (0004h) Inst (0005h) Instruction executed Inst (PC-1) Inst (PC) Dummy cycle Dummy cycle Inst (0004h) Note 1: T0IF interrupt flag is sampled here (every Q1). 2: Interrupt latency = 3.25Tcy, where Tcy = instruction cycle time. 3: CLKOUT is available only in RC oscillator mode. 4: The timer clock (after the synchronizer circuit) which increments the timer from FFh to 00h immediately sets the T0IF bit. The TMR0 register will roll over 3 Tosc cycles later. DS30430D-page 28  1996-2013 Microchip Technology Inc.

PIC16F8X 6.2 Using TMR0 with External Clock 6.2.2 TMR0 INCREMENT DELAY When an external clock input is used for TMR0, it must Since the prescaler output is synchronized with the meet certain requirements. The external clock internal clocks, there is a small delay from the time the requirement is due to internal phase clock (TOSC) external clock edge occurs to the time the Timer0 synchronization. Also, there is a delay in the actual Module is actually incremented. Figure6-5 shows the incrementing of the TMR0 register after delay from the external clock edge to the timer synchronization. incrementing. 6.2.1 EXTERNAL CLOCK SYNCHRONIZATION 6.3 Prescaler When no prescaler is used, the external clock input is An 8-bit counter is available as a prescaler for the the same as the prescaler output. The synchronization Timer0 Module, or as a postscaler for the Watchdog of pin RA4/T0CKI with the internal phase clocks is Timer (Figure6-6). For simplicity, this counter is being accomplished by sampling the prescaler output on the referred to as “prescaler” throughout this data sheet. Q2 and Q4 cycles of the internal phase clocks Note that there is only one prescaler available which is (Figure6-5). Therefore, it is necessary for T0CKI to be mutually exclusive between the Timer0 Module and the high for at least 2Tosc (plus a small RC delay) and low Watchdog Timer. Thus, a prescaler assignment for the for at least 2Tosc (plus a small RC delay). Refer to the Timer0 Module means that there is no prescaler for the electrical specification of the desired device. Watchdog Timer, and vice-versa. When a prescaler is used, the external clock input is The PSA and PS2:PS0 bits (OPTION_REG<3:0>) divided by an asynchronous ripple counter type determine the prescaler assignment and prescale ratio. prescaler so that the prescaler output is symmetrical. When assigned to the Timer0 Module, all instructions For the external clock to meet the sampling writing to the Timer0 Module (e.g., CLRF 1, MOVWF requirement, the ripple counter must be taken into 1, BSF 1,x ....etc.) will clear the prescaler. When account. Therefore, it is necessary for T0CKI to have a assigned to WDT, a CLRWDT instruction will clear the period of at least 4Tosc (plus a small RC delay) divided prescaler along with the Watchdog Timer. The by the prescaler value. The only requirement on T0CKI prescaler is not readable or writable. high and low time is that they do not violate the minimum pulse width requirement of 10 ns. Refer to parameters 40, 41 and 42 in the AC Electrical Specifications of the desired device.  1996-2013 Microchip Technology Inc. DS30430D-page 29

PIC16F8X FIGURE 6-5: TIMER0 TIMING WITH EXTERNAL CLOCK Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Ext. Clock Input or Prescaler Out (Note 2) (Note 3) Ext. Clock/Prescaler Output After Sampling Increment TMR0 (Q4) TMR0 T0 T0 + 1 T0 + 2 Note 1: Delay from clock input change to TMR0 increment is 3Tosc to 7Tosc. (Duration of Q = Tosc). Therefore, the error in measuring the interval between two edges on TMR0 input =  4Tosc max. 2: External clock if no prescaler selected, Prescaler output otherwise. 3: The arrows  indicate where sampling occurs. A small clock pulse may be missed by sampling. FIGURE 6-6: BLOCK DIAGRAM OF THE TMR0/WDT PRESCALER CLKOUT (= Fosc/4) Data Bus M 8 0 1 RA4/T0CKI U M SYNC pin 1 X 0 U 2 TMR0 register X Cycles T0SE T0CS PSA Set bit T0IF on overflow 0 8-bit Prescaler M U Watchdog 1 X 8 Timer 8 - to - 1MUX PS2:PS0 PSA 0 1 WDT Enable bit M U X PSA WDT time-out Note: T0CS, T0SE, PSA, PS2:PS0 are bits in the OPTION_REG register. DS30430D-page 30  1996-2013 Microchip Technology Inc.

PIC16F8X 6.3.1 SWITCHING PRESCALER ASSIGNMENT EXAMPLE 6-1: CHANGING PRESCALER (TIMER0WDT) The prescaler assignment is fully under software BCF STATUS, RP0 ;Bank 0 control (i.e., it can be changed “on the fly” during CLRF TMR0 ;Clear TMR0 program execution). ; and Prescaler BSF STATUS, RP0 ;Bank 1 Note: To avoid an unintended device RESET, the CLRWDT ;Clears WDT following instruction sequence MOVLW b'xxxx1xxx' ;Select new (Example6-1) must be executed when MOVWF OPTION_REG ; prescale value changing the prescaler assignment from BCF STATUS, RP0 ;Bank 0 Timer0 to the WDT. This sequence must be taken even if the WDT is disabled. To EXAMPLE 6-2: CHANGING PRESCALER change prescaler from the WDT to the (WDTTIMER0) Timer0 module use the sequence shown in CLRWDT ;Clear WDT and Example6-2. ; prescaler BSF STATUS, RP0 ;Bank 1 MOVLW b'xxxx0xxx' ;Select TMR0, new ; prescale value ’ and clock source MOVWF OPTION_REG ; BCF STATUS, RP0 ;Bank 0 TABLE 6-1 REGISTERS ASSOCIATED WITH TIMER0 Value on Value on all Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Power-on other resets Reset 01h TMR0 Timer0 module’s register xxxx xxxx uuuu uuuu 0Bh INTCON GIE EEIE T0IE INTE RBIE T0IF INTF RBIF 0000 000x 0000 0000 OPTION_ 1111 1111 1111 1111 81h RBPU INTEDG T0CS T0SE PSA PS2 PS1 PS0 REG 85h TRISA — — — TRISA4 TRISA3 TRISA2 TRISA1 TRISA0 ---1 1111 ---1 1111 Legend: x = unknown, u = unchanged. - = unimplemented read as '0'. Shaded cells are not associated with Timer0.  1996-2013 Microchip Technology Inc. DS30430D-page 31

PIC16F8X NOTES: DS30430D-page 32  1996-2013 Microchip Technology Inc.

PIC16F8X 7.0 DATA EEPROM MEMORY data memory is rated for high erase/write cycles. The write time is controlled by an on-chip timer. The write- The EEPROM data memory is readable and writable time will vary with voltage and temperature as well as during normal operation (full VDD range). This memory from chip to chip. Please refer to AC specifications for is not directly mapped in the register file space. Instead exact limits. it is indirectly addressed through the Special Function Registers. There are four SFRs used to read and write When the device is code protected, the CPU may this memory. These registers are: continue to read and write the data EEPROM memory. The device programmer can no longer access (cid:129) EECON1 thismemory. (cid:129) EECON2 (cid:129) EEDATA 7.1 EEADR (cid:129) EEADR The EEADR register can address up to a maximum of EEDATA holds the 8-bit data for read/write, and EEADR 256 bytes of data EEPROM. Only the first 64 bytes of holds the address of the EEPROM location being data EEPROM are implemented. accessed. PIC16F8X devices have 64 bytes of data EEPROM with an address range from 0h to 3Fh. The upper two bits are address decoded. This means that these two bits must always be '0' to ensure that the The EEPROM data memory allows byte read and write. address is in the 64 byte memory space. A byte write automatically erases the location and writes the new data (erase before write). The EEPROM FIGURE 7-1: EECON1 REGISTER (ADDRESS 88h) U U U R/W-0 R/W-x R/W-0 R/S-0 R/S-x — — — EEIF WRERR WREN WR RD R = Readable bit bit7 bit0 W = Writable bit S = Settable bit U = Unimplemented bit, read as ‘0’ - n = Value at POR reset bit 7:5 Unimplemented: Read as '0' bit 4 EEIF: EEPROM Write Operation Interrupt Flag bit 1 = The write operation completed (must be cleared in software) 0 = The write operation is not complete or has not been started bit 3 WRERR: EEPROM Error Flag bit 1 = A write operation is prematurely terminated (any MCLR reset or any WDT reset during normal operation) 0 = The write operation completed bit 2 WREN: EEPROM Write Enable bit 1 = Allows write cycles 0 = Inhibits write to the data EEPROM bit 1 WR: Write Control bit 1 = initiates a write cycle. (The bit is cleared by hardware once write is complete. The WR bit can only be set (not cleared) in software. 0 = Write cycle to the data EEPROM is complete bit 0 RD: Read Control bit 1 = Initiates an EEPROM read (read takes one cycle. RD is cleared in hardware. The RD bit can only be set (not cleared) in software). 0 = Does not initiate an EEPROM read  1996-2013 Microchip Technology Inc. DS30430D-page 33

PIC16F8X 7.2 EECON1 and EECON2 Registers 7.4 Writing to the EEPROM Data Memory EECON1 is the control register with five low order bits To write an EEPROM data location, the user must first physically implemented. The upper-three bits are non- write the address to the EEADR register and the data existent and read as '0's. to the EEDATA register. Then the user must follow a specific sequence to initiate the write for each byte. Control bits RD and WR initiate read and write, respectively. These bits cannot be cleared, only set, in EXAMPLE 7-1: DATA EEPROM WRITE software. They are cleared in hardware at completion of the read or write operation. The inability to clear the BSF STATUS, RP0 ; Bank 1 WR bit in software prevents the accidental, premature BCF INTCON, GIE ; Disable INTs. termination of a write operation. BSF EECON1, WREN ; Enable Write MOVLW 55h ; The WREN bit, when set, will allow a write operation. MOVWF EECON2 ; Write 55h On power-up, the WREN bit is clear. The WRERR bit is sreest ewt hoer na Wa DwTri tteim oep-eoruatt rioens eits d iunrteinrgru npotermd abl yo pae MraCtioLnR. quired quence MMBOOSVVFLW WF AEEAEEhCC OO NN 21 , W R ;;; WSreitt eW RA Abhit In these situations, following reset, the user can check Re Se ; begin write the WRERR bit and rewrite the location. The data and BSF INTCON, GIE ; Enable INTs. address will be unchanged in the EEDATA and The write will not initiate if the above sequence is not EEADRregisters. exactly followed (write 55h to EECON2, write AAh to Interrupt flag bit EEIF is set when write is complete. It EECON2, then set WR bit) for each byte. We strongly must be cleared in software. recommend that interrupts be disabled during this codesegment. EECON2 is not a physical register. Reading EECON2 will read all '0's. The EECON2 register is used Additionally, the WREN bit in EECON1 must be set to exclusively in the Data EEPROM write sequence. enable write. This mechanism prevents accidental writes to data EEPROM due to errant (unexpected) 7.3 Reading the EEPROM Data Memory code execution (i.e., lost programs). The user should keep the WREN bit clear at all times, except when To read a data memory location, the user must write the updating EEPROM. The WREN bit is not cleared address to the EEADR register and then set control bit byhardware RD (EECON1<0>). The data is available, in the very next cycle, in the EEDATA register; therefore it can be After a write sequence has been initiated, clearing the read in the next instruction. EEDATA will hold this value WREN bit will not affect this write cycle. The WR bit will until another read or until it is written to by the user be inhibited from being set unless the WREN bit is set. (during a write operation). At the completion of the write cycle, the WR bit is cleared in hardware and the EE Write Complete EXAMPLE 7-1: DATA EEPROM READ Interrupt Flag bit (EEIF) is set. The user can either enable this interrupt or poll this bit. EEIF must be BCF STATUS, RP0 ; Bank 0 cleared by software. MOVLW CONFIG_ADDR ; MOVWF EEADR ; Address to read BSF STATUS, RP0 ; Bank 1 BSF EECON1, RD ; EE Read BCF STATUS, RP0 ; Bank 0 MOVF EEDATA, W ; W = EEDATA DS30430D-page 34  1996-2013 Microchip Technology Inc.

PIC16F8X 7.5 Write Verify SUBWF EEDATA, W ; BTFSS STATUS, Z ; Is difference 0? Depending on the application, good programming prac- GOTO WRITE_ERR ; NO, Write error tice may dictate that the value written to the Data : ; YES, Good write EEPROM should be verified (Example7-1) to the : ; Continue program desired value to be written. This should be used in 7.6 Protection Against Spurious Writes applications where an EEPROM bit will be stressed near the specification limit. The Total Endurance disk There are conditions when the device may not want to will help determine your comfort level. write to the data EEPROM memory. To protect against Generally the EEPROM write failure will be a bit which spurious EEPROM writes, various mechanisms have was written as a '1', but reads back as a '0' (due to been built in. On power-up, WREN is cleared. Also, the leakage off the bit). Power-up Timer (72 ms duration) prevents EEPROMwrite. EXAMPLE 7-1: WRITE VERIFY The write initiate sequence and the WREN bit together help prevent an accidental write during brown-out, BCF STATUS, RP0 ; Bank 0 power glitch, or software malfunction. : ; Any code can go here : ; 7.7 Data EEPROM Operation during Code MOVF EEDATA, W ; Must be in Bank 0 BSF STATUS, RP0 ; Bank 1 Protect READ BSF EECON1, RD ; YES, Read the When the device is code protected, the CPU is able to ; value written read and write unscrambled data to the Data EEPROM. BCF STATUS, RP0 ; Bank 0 For ROM devices, there are two code protection bits ; (Section8.1). One for the ROM program memory and ; Is the value written (in W reg) and one for the Data EEPROM memory. ; read (in EEDATA) the same? ; TABLE 7-1 REGISTERS/BITS ASSOCIATED WITH DATA EEPROM Value on Value on all Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Power-on other resets Reset 08h EEDATA EEPROM data register xxxx xxxx uuuu uuuu 09h EEADR EEPROM address register xxxx xxxx uuuu uuuu 88h EECON1 — — — EEIF WRERR WREN WR RD ---0 x000 ---0 q000 89h EECON2 EEPROM control register 2 ---- ---- ---- ---- Legend: x = unknown, u = unchanged, - = unimplemented read as '0', q = value depends upon condition. Shaded cells are not used by Data EEPROM.  1996-2013 Microchip Technology Inc. DS30430D-page 35

PIC16F8X NOTES: DS30430D-page 36  1996-2013 Microchip Technology Inc.

PIC16F8X 8.0 SPECIAL FEATURES OF THE CPU What sets a microcontroller apart from other processors are special circuits to deal with the needs of real time applications. The PIC16F8X has a host of such features intended to maximize system reliability, minimize cost through elimination of external components, provide power saving operating modes and offer code protection. These features are: (cid:129) OSC Selection (cid:129) Reset - Power-on Reset (POR) - Power-up Timer (PWRT) - Oscillator Start-up Timer (OST) (cid:129) Interrupts (cid:129) Watchdog Timer (WDT) (cid:129) SLEEP (cid:129) Code protection (cid:129) ID locations (cid:129) In-circuit serial programming The PIC16F8X has a Watchdog Timer which can be shut off only through configuration bits. It runs off its own RC oscillator for added reliability. There are two timers that offer necessary delays on power-up. One is the Oscillator Start-up Timer (OST), intended to keep the chip in reset until the crystal oscillator is stable. The other is the Power-up Timer (PWRT), which provides a fixed delay of 72 ms (nominal) on power-up only. This design keeps the device in reset while the power supply stabilizes. With these two timers on-chip, most applications need no external reset circuitry. SLEEP mode offers a very low current power-down mode. The user can wake-up from SLEEP through external reset, Watchdog Timer time-out or through an interrupt. Several oscillator options are provided to allow the part to fit the application. The RC oscillator option saves system cost while the LP crystal option saves power. A set of configuration bits are used to select the various options.  1996-2013 Microchip Technology Inc. DS30430D-page 37

PIC16F8X 8.1 Configuration Bits Address 2007h is beyond the user program memory space and it belongs to the special test/configuration The configuration bits can be programmed (read as '0') memory space (2000h - 3FFFh). This space can only or left unprogrammed (read as '1') to select various be accessed during programming. device configurations. These bits are mapped in To find out how to program the PIC16C84, refer to program memory location 2007h. PIC16C84 EEPROM Memory Programming Specifica- tion (DS30189). FIGURE 8-1: CONFIGURATION WORD - PIC16CR83 AND PIC16CR84 R-u R-u R-u R-u R-u R-u R/P-u R-u R-u R-u R-u R-u R-u R-u CP CP CP CP CP CP DP CP CP CP PWRTE WDTE FOSC1 FOSC0 bit13 bit0 R = Readable bit P = Programmable bit - n = Value at POR reset u = unchanged bit 13:8 CP: Program Memory Code Protection bit 1 = Code protection off 0 = Program memory is code protected bit 7 DP: Data Memory Code Protection bit 1 = Code protection off 0 = Data memory is code protected bit 6:4 CP: Program Memory Code Protection bit 1 = Code protection off 0 = Program memory is code protected bit 3 PWRTE: Power-up Timer Enable bit 1 = Power-up timer is disabled 0 = Power-up timer is enabled bit 2 WDTE: Watchdog Timer Enable bit 1 = WDT enabled 0 = WDT disabled bit 1:0 FOSC1:FOSC0: Oscillator Selection bits 11 =RC oscillator 10 =HS oscillator 01 =XT oscillator 00 =LP oscillator DS30430D-page 38  1996-2013 Microchip Technology Inc.

PIC16F8X FIGURE 8-2: CONFIGURATION WORD - PIC16F83 AND PIC16F84 R/P-u R/P-u R/P-u R/P-u R/P-u R/P-u R/P-u R/P-u R/P-u R/P-u R/P-u R/P-u R/P-u R/P-u CP CP CP CP CP CP CP CP CP CP PWRTE WDTE FOSC1 FOSC0 bit13 bit0 R = Readable bit P = Programmable bit - n = Value at POR reset u = unchanged bit 13:4 CP: Code Protection bit 1 = Code protection off 0 = All memory is code protected bit 3 PWRTE: Power-up Timer Enable bit 1 = Power-up timer is disabled 0 = Power-up timer is enabled bit 2 WDTE: Watchdog Timer Enable bit 1 = WDT enabled 0 = WDT disabled bit 1:0 FOSC1:FOSC0: Oscillator Selection bits 11 =RC oscillator 10 =HS oscillator 01 =XT oscillator 00 =LP oscillator 8.2 Oscillator Configurations FIGURE 8-3: CRYSTAL/CERAMIC RESONATOR OPERATION 8.2.1 OSCILLATOR TYPES (HS, XT OR LP OSC CONFIGURATION) The PIC16F8X can be operated in four different oscillator modes. The user can program two C1(1) OSC1 configuration bits (FOSC1 and FOSC0) to select one of these four modes: To internal (cid:129) LP Low Power Crystal XTAL RF(3) logic (cid:129) XT Crystal/Resonator OSC2 SLEEP (cid:129) HS High Speed Crystal/Resonator RS(2) (cid:129) RC Resistor/Capacitor C2(1) PIC16FXX 8.2.2 CRYSTAL OSCILLATOR / CERAMIC Note1: See Table8-1 for recommended values of RESONATORS C1 and C2. 2: A series resistor (RS) may be required for In XT, LP or HS modes a crystal or ceramic resonator AT strip cut crystals. is connected to the OSC1/CLKIN and OSC2/CLKOUT 3: RF varies with the crystal chosen. pins to establish oscillation (Figure8-3). The PIC16F8X oscillator design requires the use of a parallel cut crystal. Use of a series cut crystal may give a frequency out of the crystal manufacturers specifications. When in XT, LP or HS modes, the device can have an external clock source to drive the OSC1/CLKIN pin (Figure8-4).  1996-2013 Microchip Technology Inc. DS30430D-page 39

PIC16F8X FIGURE 8-4: EXTERNAL CLOCK INPUT Crystals Tested: OPERATION (HS, XT OR LP OSC CONFIGURATION) 32.768 kHz Epson C-001R32.768K-A  20 PPM 100 kHz Epson C-2 100.00 KC-P  20 PPM 200 kHz STD XTL 200.000 KHz  20 PPM Clock from OSC1 1.0 MHz ECS ECS-10-13-2  50 PPM ext. system PIC16FXX 2.0 MHz ECS ECS-20-S-2  50 PPM Open OSC2 4.0 MHz ECS ECS-40-S-4  50 PPM 10.0 MHz ECS ECS-100-S-4  50 PPM TABLE 8-1 CAPACITOR SELECTION FOR 8.2.3 EXTERNAL CRYSTAL OSCILLATOR CERAMIC RESONATORS CIRCUIT Either a prepackaged oscillator can be used or a simple Ranges Tested: oscillator circuit with TTL gates can be built. Mode Freq OSC1/C1 OSC2/C2 Prepackaged oscillators provide a wide operating range and better stability. A well-designed crystal XT 455 kHz 47 - 100 pF 47 - 100 pF oscillator will provide good performance with TTL 2.0 MHz 15 - 33 pF 15 - 33 pF gates. Two types of crystal oscillator circuits are 4.0 MHz 15 - 33 pF 15 - 33 pF available; one with series resonance, and one with HS 8.0 MHz 15 - 33 pF 15 - 33 pF parallel resonance. 10.0 MHz 15 - 33 pF 15 - 33 pF Figure8-5 shows a parallel resonant oscillator circuit. Note: Recommended values of C1 and C2 are identical to The circuit is designed to use the fundamental the ranges tested table. frequency of the crystal. The 74AS04 inverter performs Higher capacitance increases the stability of the the 180-degree phase shift that a parallel oscillator oscillator but also increases the start-up time. These values are for design guidance only. Since requires. The 4.7k resistor provides negative each resonator has its own characteristics, the user feedback for stability. The 10 k potentiometer biases should consult the resonator manufacturer for the the 74AS04 in the linear region. This could be used for appropriate values of external components. external oscillator designs. Resonators Tested: FIGURE 8-5: EXTERNAL PARALLEL 455 kHz Panasonic EFO-A455K04B 0.3% RESONANT CRYSTAL 2.0 MHz Murata Erie CSA2.00MG 0.5% OSCILLATOR CIRCUIT 4.0 MHz Murata Erie CSA4.00MG 0.5% 8.0 MHz Murata Erie CSA8.00MT  0.5% +5V To Other 10.0 MHz Murata Erie CSA10.00MTZ 0.5% Devices 10k PIC16FXX None of the resonators had built-in capacitors. 4.7k 74AS04 TABLE 8-2 CAPACITOR SELECTION FOR 74AS04 CLKIN CRYSTAL OSCILLATOR Mode Freq OSC1/C1 OSC2/C2 10k LP 32 kHz 68 - 100 pF 68 - 100 pF XTAL 200 kHz 15 - 33 pF 15 - 33 pF 10k XT 100 kHz 100 - 150 pF 100 - 150 pF 2 MHz 15 - 33 pF 15 - 33 pF 20 pF 20 pF 4 MHz 15 - 33 pF 15 - 33 pF HS 4 MHz 15 - 33 pF 15 - 33 pF 10 MHz 15 - 33 pF 15 - 33 pF Figure8-6 shows a series resonant oscillator circuit. This circuit is also designed to use the fundamental Note: Higher capacitance increases the stability of oscillator but also increases the start-up time. frequency of the crystal. The inverter performs a These values are for design guidance only. Rs may 180-degree phase shift. The 330 k resistors provide be required in HS mode as well as XT mode to the negative feedback to bias the inverters in their avoid overdriving crystals with low drive level speci- linear region. fication. Since each crystal has its own characteris- tics, the user should consult the crystal manufacturer for appropriate values of external components. For VDD > 4.5V, C1 = C2  30 pF is recommended. DS30430D-page 40  1996-2013 Microchip Technology Inc.

PIC16F8X FIGURE 8-6: EXTERNAL SERIES FIGURE 8-7: RC OSCILLATOR MODE RESONANT CRYSTAL VDD OSCILLATOR CIRCUIT Rext Internal OSC1 To Other clock 330 k 330 k Devices PIC16FXX Cext PIC16FXX 74AS04 74AS04 74AS04 VSS CLKIN OSC2/CLKOUT 0.1F Fosc/4 XTAL Recommended values: 5 k  Rext  100 k Cext > 20pF Note: When the device oscillator is in RC mode, 8.2.4 RC OSCILLATOR do not drive the OSC1 pin with an external clock or you may damage the device. For timing insensitive applications the RC device option 8.3 Reset offers additional cost savings. The RC oscillator frequency is a function of the supply voltage, the The PIC16F8X differentiates between various kinds resistor (Rext) values, capacitor (Cext) values, and the ofreset: operating temperature. In addition to this, the oscillator frequency will vary from unit to unit due to normal (cid:129) Power-on Reset (POR) process parameter variation. Furthermore, the (cid:129) MCLR reset during normal operation difference in lead frame capacitance between package (cid:129) MCLR reset during SLEEP types also affects the oscillation frequency, especially (cid:129) WDT Reset (during normal operation) for low Cext values. The user needs to take into (cid:129) WDT Wake-up (during SLEEP) account variation due to tolerance of the external RandC components. Figure8-7 shows how an R/C Figure8-8 shows a simplified block diagram of the combination is connected to the PIC16F8X. For Rext on-chip reset circuit. The MCLR reset path has a noise values below 4k, the oscillator operation may filter to ignore small pulses. The electrical specifica- become unstable, or stop completely. For very high tions state the pulse width requirements for the MCLR Rext values (e.g., 1M), the oscillator becomes pin. sensitive to noise, humidity and leakage. Thus, we Some registers are not affected in any reset condition; recommend keeping Rext between 5 k and 100 k. their status is unknown on a POR reset and unchanged Although the oscillator will operate with no external in any other reset. Most other registers are reset to a capacitor (Cext = 0 pF), we recommend using values “reset state” on POR, MCLR or WDT reset during above 20 pF for noise and stability reasons. With little normal operation and on MCLR reset during SLEEP. or no external capacitance, the oscillation frequency They are not affected by a WDT reset during SLEEP, can vary dramatically due to changes in external since this reset is viewed as the resumption of normal capacitances, such as PCB trace capacitance or operation. package lead frame capacitance. Table8-3 gives a description of reset conditions for the See the electrical specification section for RC program counter (PC) and the STATUS register. frequency variation from part to part due to normal Table8-4 gives a full description of reset states for all process variation. The variation is larger for larger R registers. (since leakage current variation will affect RC The TO and PD bits are set or cleared differently in dif- frequency more for large R) and for smaller C (since ferent reset situations (Section8.7). These bits are variation of input capacitance has a greater affect on used in software to determine the nature of the reset. RC frequency). See the electrical specification section for variation of oscillator frequency due to VDD for given Rext/Cext values as well as frequency variation due to operatingtemperature. The oscillator frequency, divided by 4, is available on the OSC2/CLKOUT pin, and can be used for test purposes or to synchronize other logic (see Figure3-2 for waveform).  1996-2013 Microchip Technology Inc. DS30430D-page 41

PIC16F8X FIGURE 8-8: SIMPLIFIED BLOCK DIAGRAM OF ON-CHIP RESET CIRCUIT External Reset MCLR SLEEP WDT WDT Module Time_Out Reset VDD rise detect Power_on_Reset S VDD OST/PWRT OST Chip_Reset 10-bit Ripple counter R Q OSC1/ CLKIN PWRT On-chip RC OSC(1) 10-bit Ripple counter Enable PWRT See Table8-5 Note 1: This is a separate oscillator from the Enable OST RC oscillator of the CLKIN pin. DS30430D-page 42  1996-2013 Microchip Technology Inc.

PIC16F8X TABLE 8-3 RESET CONDITION FOR PROGRAM COUNTER AND THE STATUS REGISTER Condition Program Counter STATUS Register Power-on Reset 000h 0001 1xxx MCLR Reset during normal operation 000h 000u uuuu MCLR Reset during SLEEP 000h 0001 0uuu WDT Reset (during normal operation) 000h 0000 1uuu WDT Wake-up PC + 1 uuu0 0uuu Interrupt wake-up from SLEEP PC + 1 (1) uuu1 0uuu Legend: u = unchanged, x = unknown. Note1: When the wake-up is due to an interrupt and the GIE bit is set, the PC is loaded with the interrupt vector (0004h). TABLE 8-4 RESET CONDITIONS FOR ALL REGISTERS MCLR Reset during: Wake-up from SLEEP: – normal operation – through interrupt Register Address Power-on Reset – SLEEP – through WDT Time-out WDT Reset during nor- mal operation W — xxxx xxxx uuuu uuuu uuuu uuuu INDF 00h ---- ---- ---- ---- ---- ---- TMR0 01h xxxx xxxx uuuu uuuu uuuu uuuu PCL 02h 0000h 0000h PC + 1(2) STATUS 03h 0001 1xxx 000q quuu(3) uuuq quuu(3) FSR 04h xxxx xxxx uuuu uuuu uuuu uuuu PORTA 05h ---x xxxx ---u uuuu ---u uuuu PORTB 06h xxxx xxxx uuuu uuuu uuuu uuuu EEDATA 08h xxxx xxxx uuuu uuuu uuuu uuuu EEADR 09h xxxx xxxx uuuu uuuu uuuu uuuu PCLATH 0Ah ---0 0000 ---0 0000 ---u uuuu INTCON 0Bh 0000 000x 0000 000u uuuu uuuu(1) INDF 80h ---- ---- ---- ---- ---- ---- OPTION_REG 81h 1111 1111 1111 1111 uuuu uuuu PCL 82h 0000h 0000h PC + 1 STATUS 83h 0001 1xxx 000q quuu(3) uuuq quuu(3) FSR 84h xxxx xxxx uuuu uuuu uuuu uuuu TRISA 85h ---1 1111 ---1 1111 ---u uuuu TRISB 86h 1111 1111 1111 1111 uuuu uuuu EECON1 88h ---0 x000 ---0 q000 ---0 uuuu EECON2 89h ---- ---- ---- ---- ---- ---- PCLATH 8Ah ---0 0000 ---0 0000 ---u uuuu INTCON 8Bh 0000 000x 0000 000u uuuu uuuu(1) Legend: u = unchanged, x = unknown, - = unimplemented bit read as '0', q = value depends on condition. Note1: One or more bits in INTCON will be affected (to cause wake-up). 2: When the wake-up is due to an interrupt and the GIE bit is set, the PC is loaded with the interrupt vector (0004h). 3: Table8-3 lists the reset value for each specific condition.  1996-2013 Microchip Technology Inc. DS30430D-page 43

PIC16F8X 8.4 Power-on Reset (POR) FIGURE 8-9: EXTERNAL POWER-ON RESET CIRCUIT (FOR SLOW A Power-on Reset pulse is generated on-chip when VDD POWER-UP) VDD rise is detected (in the range of 1.2V - 1.7V). To take advantage of the POR, just tie the MCLR pin directly (or through a resistor) to VDD. This will VDD VDD eliminate external RC components usually needed to create Power-on Reset. A minimum rise time for VDD D R must be met for this to operate properly. See Electrical R1 Specifications for details. MCLR When the device starts normal operation (exits the C PIC16FXX reset condition), device operating parameters (voltage, frequency, temperature, ...) must be meet to ensure operation. If these conditions are not met, the device Note1: External Power-on Reset circuit is required must be held in reset until the operating conditions only if VDD power-up rate is too slow. The aremet. diode D helps discharge the capacitor For additional information, refer to Application Note quickly when VDD powers down. 2: R < 40 k is recommended to make sure AN607, "Power-up Trouble Shooting." that voltage drop across R does not exceed The POR circuit does not produce an internal reset 0.2V (max leakage current spec on MCLR when VDD declines. pin is 5 A). A larger voltage drop will 8.5 Power-up Timer (PWRT) degrade VIH level on the MCLR pin. 3: R1 = 100 to 1 k will limit any current The Power-up Timer (PWRT) provides a fixed 72 ms flowing into MCLR from external nominal time-out (TPWRT) from POR (Figure8-10, capacitor C in the event of an MCLR pin Figure8-11, Figure8-12 and Figure8-13). The breakdown due to ESD or EOS. Power-up Timer operates on an internal RC oscillator. The chip is kept in reset as long as the PWRT is active. The PWRT delay allows the VDD to rise to an accept- able level (Possible exception shown in Figure8-13). A configuration bit, PWRTE, can enable/disable the PWRT. See either Figure8-1 or Figure8-2 for the oper- ation of the PWRTE bit for a particular device. The power-up time delay TPWRT will vary from chip to chip due to VDD, temperature, and process variation. See DC parameters for details. 8.6 Oscillator Start-up Timer (OST) The Oscillator Start-up Timer (OST) provides a 1024 oscillator cycle delay (from OSC1 input) after the PWRT delay ends (Figure8-10, Figure8-11, Figure8-12 and Figure8-13). This ensures the crystal oscillator or resonator has started and stabilized. The OST time-out (TOST) is invoked only for XT, LP and HS modes and only on Power-on Reset or wake-up from SLEEP. When VDD rises very slowly, it is possible that the TPWRT time-out and TOST time-out will expire before VDD has reached its final value. In this case (Figure8-13), an external power-on reset circuit may be necessary (Figure8-9). DS30430D-page 44  1996-2013 Microchip Technology Inc.

PIC16F8X FIGURE 8-10: TIME-OUT SEQUENCE ON POWER-UP (MCLR NOT TIED TO VDD): CASE 1 VDD MCLR INTERNAL POR TPWRT PWRT TIME-OUT TOST OST TIME-OUT INTERNAL RESET FIGURE 8-11: TIME-OUT SEQUENCE ON POWER-UP (MCLR NOT TIED TO VDD): CASE 2 VDD MCLR INTERNAL POR TPWRT PWRT TIME-OUT TOST OST TIME-OUT INTERNAL RESET  1996-2013 Microchip Technology Inc. DS30430D-page 45

PIC16F8X FIGURE 8-12: TIME-OUT SEQUENCE ON POWER-UP (MCLR TIED TO VDD): FAST VDD RISE TIME VDD MCLR INTERNAL POR TPWRT PWRT TIME-OUT TOST OST TIME-OUT INTERNAL RESET FIGURE 8-13: TIME-OUT SEQUENCE ON POWER-UP (MCLR TIED TO VDD): SLOW VDD RISE TIME V1 VDD MCLR INTERNAL POR TPWRT PWRT TIME-OUT TOST OST TIME-OUT INTERNAL RESET When VDD rises very slowly, it is possible that the TPWRT time-out and TOST time-out will expire before VDD has reached its final value. In this example, the chip will reset properly if, and only if, V1  VDD min. DS30430D-page 46  1996-2013 Microchip Technology Inc.

PIC16F8X 8.7 Time-out Sequence and Power-down 8.8 Reset on Brown-Out Status Bits (TO/PD) A brown-out is a condition where device power (VDD) On power-up (Figure8-10, Figure8-11, Figure8-12 dips below its minimum value, but not to zero, and then and Figure8-13) the time-out sequence is as follows: recovers. The device should be reset in the event of a First PWRT time-out is invoked after a POR has brown-out. expired. Then the OST is activated. The total time-out To reset a PIC16F8X device when a brown-out occurs, will vary based on oscillator configuration and PWRTE external brown-out protection circuits may be built, as configuration bit status. For example, in RC mode with shown in Figure8-14 and Figure8-15. the PWRT disabled, there will be no time-out at all. TABLE 8-5 TIME-OUT IN VARIOUS FIGURE 8-14: BROWN-OUT PROTECTION SITUATIONS CIRCUIT 1 Oscillator Power-up Wake-up VDD Configuration PWRT PWRT from VDD Enabled Disabled SLEEP 33k XT, HS, LP 72 ms + 1024TOSC 1024TOSC 1024TOSC 10k MCLR RC 72 ms — — 40k Since the time-outs occur from the POR reset pulse, if PIC16F8X MCLR is kept low long enough, the time-outs will expire. Then bringing MCLR high, execution will begin immediately (Figure8-10). This is useful for testing purposes or to synchronize more than one PIC16F8X device when operating in parallel. This circuit will activate reset when VDD goes below (Vz + 0.7V) where Vz = Zener voltage. Table8-6 shows the significance of the TO and PD bits. Table8-3 lists the reset conditions for some special registers, while Table8-4 lists the reset conditions for FIGURE 8-15: BROWN-OUT PROTECTION all the registers. CIRCUIT 2 TABLE 8-6 STATUS BITS AND THEIR VDD SIGNIFICANCE VDD R1 TO PD Condition 1 1 Power-on Reset Q1 MCLR 0 x Illegal, TO is set on POR R2 40k x 0 Illegal, PD is set on POR PIC16F8X 0 1 WDT Reset (during normal operation) 0 0 WDT Wake-up 1 1 MCLR Reset during normal operation 1 0 MCLR Reset during SLEEP or interrupt This brown-out circuit is less expensive, although less wake-up from SLEEP accurate. Transistor Q1 turns off when VDD is below a certain level such that: R1 VDD (cid:129) = 0.7V R1 + R2  1996-2013 Microchip Technology Inc. DS30430D-page 47

PIC16F8X 8.9 Interrupts The RB0/INT pin interrupt, the RB port change interrupt and the TMR0 overflow interrupt flags are contained in The PIC16F8X has 4 sources of interrupt: the INTCON register. (cid:129) External interrupt RB0/INT pin When an interrupt is responded to; the GIE bit is (cid:129) TMR0 overflow interrupt cleared to disable any further interrupt, the return (cid:129) PORTB change interrupts (pins RB7:RB4) address is pushed onto the stack and the PC is loaded with 0004h. For external interrupt events, such as the (cid:129) Data EEPROM write complete interrupt RB0/INT pin or PORTB change interrupt, the interrupt The interrupt control register (INTCON) records latency will be three to four instruction cycles. The individual interrupt requests in flag bits. It also contains exact latency depends when the interrupt event occurs the individual and global interrupt enable bits. (Figure8-17). The latency is the same for both one and The global interrupt enable bit, GIE (INTCON<7>) two cycle instructions. Once in the interrupt service enables (if set) all un-masked interrupts or disables (if routine the source(s) of the interrupt can be determined cleared) all interrupts. Individual interrupts can be by polling the interrupt flag bits. The interrupt flag bit(s) disabled through their corresponding enable bits in must be cleared in software before re-enabling INTCON register. Bit GIE is cleared on reset. interrupts to avoid infinite interrupt requests. The “return from interrupt” instruction, RETFIE, exits interrupt routine as well as sets the GIE bit, which Note 1: Individual interrupt flag bits are set re-enable interrupts. regardless of the status of their corresponding mask bit or the GIE bit. FIGURE 8-16: INTERRUPT LOGIC Wake-up T0IF (If in SLEEP mode) T0IE INTF INTE Interrupt to CPU RBIF RBIE EEIF EEIE GIE DS30430D-page 48  1996-2013 Microchip Technology Inc.

PIC16F8X FIGURE 8-17: INT PIN INTERRUPT TIMING Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 OSC1 CLKOUT 3 4 INT pin 1 1 INTF flag 5 Interrupt Latency 2 (INTCON<1>) GIE bit (INTCON<7>) INSTRUCTION FLOW PC PC PC+1 PC+1 0004h 0005h Instruction fetched Inst (PC) Inst (PC+1) — Inst (0004h) Inst (0005h) Instruction Inst (PC-1) Inst (PC) Dummy Cycle Dummy Cycle Inst (0004h) executed Note 1: INTF flag is sampled here (every Q1). 2: Interrupt latency = 3-4Tcy where Tcy = instruction cycle time. Latency is the same whether Inst (PC) is a single cycle or a 2-cycle instruction. 3: CLKOUT is available only in RC oscillator mode. 4: For minimum width of INT pulse, refer to AC specs. 5: INTF is enabled to be set anytime during the Q4-Q1 cycles. 8.9.1 INT INTERRUPT 8.9.3 PORT RB INTERRUPT External interrupt on RB0/INT pin is edge triggered: An input change on PORTB<7:4> sets flag bit RBIF either rising if INTEDG bit (OPTION_REG<6>) is set, (INTCON<0>). The interrupt can be enabled/disabled or falling, if INTEDG bit is clear. When a valid edge by setting/clearing enable bit RBIE (INTCON<3>) appears on the RB0/INT pin, the INTF bit (Section5.2). (INTCON<1>) is set. This interrupt can be disabled by Note 1: For a change on the I/O pin to be clearing control bit INTE (INTCON<4>). Flag bit INTF recognized, the pulse width must be at must be cleared in software via the interrupt service least TCY wide. routine before re-enabling this interrupt. The INT interrupt can wake the processor from SLEEP (Section8.12) only if the INTE bit was set prior to going into SLEEP. The status of the GIE bit decides whether the processor branches to the interrupt vector followingwake-up. 8.9.2 TMR0 INTERRUPT An overflow (FFh  00h) in TMR0 will set flag bit T0IF (INTCON<2>). The interrupt can be enabled/disabled by setting/clearing enable bit T0IE (INTCON<5>) (Section6.0).  1996-2013 Microchip Technology Inc. DS30430D-page 49

PIC16F8X 8.10 Context Saving During Interrupts Example8-1 does the following: a) Stores the W register. During an interrupt, only the return PC value is saved on the stack. Typically, users wish to save key register b) Stores the STATUS register in STATUS_TEMP. values during an interrupt (e.g., W register and c) Executes the Interrupt Service Routine code. STATUS register). This is implemented in software. d) Restores the STATUS (and bank select bit) Example8-1 stores and restores the STATUS and W register. register’s values. The User defined registers, W_TEMP e) Restores the W register. and STATUS_TEMP are the temporary storage locations for the W and STATUS registers values. EXAMPLE 8-1: SAVING STATUS AND W REGISTERS IN RAM PUSH MOVWF W_TEMP ; Copy W to TEMP register, SWAPF STATUS, W ; Swap status to be saved into W MOVWF STATUS_TEMP ; Save status to STATUS_TEMP register ISR : : : ; Interrupt Service Routine : ; should configure Bank as required : ; POP SWAPF STATUS_TEMP, W ; Swap nibbles in STATUS_TEMP register ; and place result into W MOVWF STATUS ; Move W into STATUS register ; (sets bank to original state) SWAPF W_TEMP, F ; Swap nibbles in W_TEMP and place result in W_TEMP SWAPF W_TEMP, W ; Swap nibbles in W_TEMP and place result into W DS30430D-page 50  1996-2013 Microchip Technology Inc.

PIC16F8X 8.11 Watchdog Timer (WDT) part (see DC specs). If longer time-out periods are desired, a prescaler with a division ratio of up to 1:128 The Watchdog Timer is a free running on-chip RC can be assigned to the WDT under software control by oscillator which does not require any external writing to the OPTION_REG register. Thus, time-out components. This RC oscillator is separate from the periods up to 2.3 seconds can be realized. RC oscillator of the OSC1/CLKIN pin. That means that The CLRWDT and SLEEP instructions clear the WDT the WDT will run even if the clock on the OSC1/CLKIN and the postscaler (if assigned to the WDT) and pre- and OSC2/CLKOUT pins of the device has been vent it from timing out and generating a device stopped, for example, by execution of a SLEEP RESETcondition. instruction. During normal operation a WDT time-out generates a device RESET. If the device is in SLEEP The TO bit in the STATUS register will be cleared upon mode, a WDT Wake-up causes the device to wake-up a WDT time-out. and continue with normal operation. The WDT can be 8.11.2 WDT PROGRAMMING CONSIDERATIONS permanently disabled by programming configuration bit WDTE as a '0' (Section8.1). It should also be taken into account that under worst 8.11.1 WDT PERIOD case conditions (VDD = Min., Temperature = Max., max. WDT prescaler) it may take several seconds before a The WDT has a nominal time-out period of 18 ms, (with WDT time-out occurs. no prescaler). The time-out periods vary with temperature, VDD and process variations from part to FIGURE 8-18: WATCHDOG TIMER BLOCK DIAGRAM From TMR0 Clock Source (Figure6-6) 0 M Postscaler WDT Timer (cid:129) 1 U X 8 8 - to -1 MUX PS2:PS0 PSA WDT Enable Bit (cid:129) To TMR0 (Figure6-6) 0 1 MUX PSA WDT Time-out Note: PSA and PS2:PS0 are bits in the OPTION_REG register. TABLE 8-7 SUMMARY OF REGISTERS ASSOCIATED WITH THE WATCHDOG TIMER Value on Value on all Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Power-on other resets Reset 2007h Config. bits (2) (2) (2) (2) PWRTE(1) WDTE FOSC1 FOSC0 (2) OPTION_ 1111 1111 1111 1111 81h RBPU INTEDG T0CS T0SE PSA PS2 PS1 PS0 REG Legend: x = unknown. Shaded cells are not used by the WDT. Note 1: See Figure8-1 and Figure8-2 for operation of the PWRTE bit. 2: See Figure8-1, Figure8-2 and Section8.13 for operation of the Code and Data protection bits.  1996-2013 Microchip Technology Inc. DS30430D-page 51

PIC16F8X 8.12 Power-down Mode (SLEEP) 8.12.2 WAKE-UP FROM SLEEP A device may be powered down (SLEEP) and later The device can wake-up from SLEEP through one of powered up (Wake-up from SLEEP). the following events: 1. External reset input on MCLR pin. 8.12.1 SLEEP 2. WDT Wake-up (if WDT was enabled). The Power-down mode is entered by executing the 3. Interrupt from RB0/INT pin, RB port change, or SLEEP instruction. data EEPROM write complete. If enabled, the Watchdog Timer is cleared (but keeps Peripherals cannot generate interrupts during SLEEP, running), the PD bit (STATUS<3>) is cleared, the TO bit since no on-chip Q clocks are present. (STATUS<4>) is set, and the oscillator driver is turned The first event (MCLR reset) will cause a device reset. off. The I/O ports maintain the status they had before The two latter events are considered a continuation of the SLEEP instruction was executed (driving high, low, program execution. The TO and PD bits can be used to or hi-impedance). determine the cause of a device reset. The PD bit, For the lowest current consumption in SLEEP mode, which is set on power-up, is cleared when SLEEP is place all I/O pins at either at VDD or VSS, with no invoked. The TO bit is cleared if a WDT time-out external circuitry drawing current from the I/O pins, and occurred (and caused wake-up). disable external clocks. I/O pins that are hi-impedance While the SLEEP instruction is being executed, the next inputs should be pulled high or low externally to avoid instruction (PC + 1) is pre-fetched. For the device to switching currents caused by floating inputs. The wake-up through an interrupt event, the corresponding T0CKI input should also be at VDD or VSS. The interrupt enable bit must be set (enabled). Wake-up contribution from on-chip pull-ups on PORTB should be occurs regardless of the state of the GIE bit. If the GIE considered. bit is clear (disabled), the device continues execution at The MCLR pin must be at a logic high level (VIHMC). the instruction after the SLEEP instruction. If the GIE bit It should be noted that a RESET generated by a WDT is set (enabled), the device executes the instruction time-out does not drive the MCLR pin low. after the SLEEP instruction and then branches to the interrupt address (0004h). In cases where the execution of the instruction following SLEEP is not desirable, the user should have a NOP after the SLEEPinstruction. FIGURE 8-19: WAKE-UP FROM SLEEP THROUGH INTERRUPT Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 OSC1 CLKOUT(4) TOST(2) INT pin INTF flag (INTCON<1>) Interrupt Latency (Note 2) GIE bit Processor in (INTCON<7>) SLEEP INSTRUCTION FLOW PC PC PC+1 PC+2 PC+2 PC + 2 0004h 0005h Ifentscthruecdtion Inst(PC) = SLEEP Inst(PC + 1) Inst(PC + 2) Inst(0004h) Inst(0005h) Ienxsetcruuctetidon Inst(PC - 1) SLEEP Inst(PC + 1) Dummy cycle Dummy cycle Inst(0004h) Note 1: XT, HS or LP oscillator mode assumed. 2: TOST = 1024TOSC (drawing not to scale) This delay will not be there for RC osc mode. 3: GIE = '1' assumed. In this case after wake- up, the processor jumps to the interrupt routine. If GIE = '0', execution will continue in-line. 4: CLKOUT is not available in these osc modes, but shown here for timing reference. DS30430D-page 52  1996-2013 Microchip Technology Inc.

PIC16F8X 8.12.3 WAKE-UP USING INTERRUPTS 8.15 In-Circuit Serial Programming When global interrupts are disabled (GIE cleared) and PIC16F8X microcontrollers can be serially any interrupt source has both its interrupt enable bit programmed while in the end application circuit. This is and interrupt flag bit set, one of the following will occur: simply done with two lines for clock and data, and three (cid:129) If the interrupt occurs before the execution of a other lines for power, ground, and the programming SLEEP instruction, the SLEEP instruction will com- voltage. Customers can manufacture boards with plete as a NOP. Therefore, the WDT and WDT unprogrammed devices, and then program the postscaler will not be cleared, the TO bit will not microcontroller just before shipping the product, be set and PD bits will not be cleared. allowing the most recent firmware or custom firmware to be programmed. (cid:129) If the interrupt occurs during or after the execu- tion of a SLEEP instruction, the device will imme- The device is placed into a program/verify mode by diately wake up from sleep. The SLEEP instruction holding the RB6 and RB7 pins low, while raising the will be completely executed before the wake-up. MCLR pin from VIL to VIHH (see programming Therefore, the WDT and WDT postscaler will be specification). RB6 becomes the programming clock cleared, the TO bit will be set and the PD bit will and RB7 becomes the programming data. Both RB6 be cleared. and RB7 are Schmitt Trigger inputs in this mode. Even if the flag bits were checked before executing a After reset, to place the device into programming/verify SLEEP instruction, it may be possible for flag bits to mode, the program counter (PC) points to location 00h. become set before the SLEEP instruction completes. To A 6-bit command is then supplied to the device, 14-bits determine whether a SLEEP instruction executed, test of program data is then supplied to or from the device, the PD bit. If the PD bit is set, the SLEEP instruction using load or read-type instructions. For complete was executed as a NOP. details of serial programming, please refer to the PIC16CXX Programming Specifications (Literature To ensure that the WDT is cleared, a CLRWDT instruc- #DS30189). tion should be executed before a SLEEP instruction. 8.13 Program Verification/Code Protection FIGURE 8-20: TYPICAL IN-SYSTEM SERIAL PROGRAMMING If the code protection bit(s) have not been CONNECTION programmed, the on-chip program memory can be read out for verification purposes. To Normal Note: Microchip does not recommend code pro- Connections External tecting widowed devices. Connector PIC16FXX Signals 8.14 ID Locations +5V VDD Four memory locations (2000h - 2003h) are designated 0V VSS as ID locations to store checksum or other code VPP MCLR/VPP identification numbers. These locations are not accessible during normal execution but are readable CLK RB6 and writable only during program/verify. Only the Data I/O RB7 4least significant bits of ID location are usable. For ROM devices, these values are submitted along with the ROM code. VDD To Normal Connections For ROM devices, both the program memory and Data EEPROM memory may be read, but only the Data EEPROM memory may be programmed.  1996-2013 Microchip Technology Inc. DS30430D-page 53

PIC16F8X DS30430D-page 54  1996-2013 Microchip Technology Inc.

PIC16F8X 9.0 INSTRUCTION SET SUMMARY The instruction set is highly orthogonal and is grouped into three basic categories: Each PIC16CXX instruction is a 14-bit word divided into an OPCODE which specifies the instruction type (cid:129) Byte-oriented operations and one or more operands which further specify the (cid:129) Bit-oriented operations operation of the instruction. The PIC16CXX instruction (cid:129) Literal and control operations set summary in Table9-2 lists byte-oriented, bit-ori- All instructions are executed within one single instruc- ented, and literal and control operations. Table9-1 tion cycle, unless a conditional test is true or the pro- shows the opcode field descriptions. gram counter is changed as a result of an instruction. For byte-oriented instructions, 'f' represents a file reg- In this case, the execution takes two instruction cycles ister designator and 'd' represents a destination desig- with the second cycle executed as a NOP. One instruc- nator. The file register designator specifies which file tion cycle consists of four oscillator periods. Thus, for register is to be used by the instruction. an oscillator frequency of 4 MHz, the normal instruction The destination designator specifies where the result of execution time is 1 s. If a conditional test is true or the program counter is changed as a result of an instruc- the operation is to be placed. If 'd' is zero, the result is placed in the W register. If 'd' is one, the result is placed tion, the instruction execution time is 2 s. in the file register specified in the instruction. Table9-2 lists the instructions recognized by the MPASM assembler. For bit-oriented instructions, 'b' represents a bit field designator which selects the number of the bit affected Figure9-1 shows the general formats that the instruc- by the operation, while 'f' represents the number of the tions can have. file in which the bit is located. Note: To maintain upward compatibility with For literal and control operations, 'k' represents an future PIC16CXX products, do not use the eight or eleven bit constant or literal value. OPTION and TRIS instructions. TABLE 9-1 OPCODE FIELD All examples use the following format to represent a DESCRIPTIONS hexadecimal number: 0xhh Field Description where h signifies a hexadecimal digit. f Register file address (0x00 to 0x7F) W Working register (accumulator) FIGURE 9-1: GENERAL FORMAT FOR b Bit address within an 8-bit file register INSTRUCTIONS k Literal field, constant data or label x Don't care location (= 0 or 1) Byte-oriented file register operations The assembler will generate code with x = 0. It is the 13 8 7 6 0 recommended form of use for compatibility with all OPCODE d f (FILE #) Microchip software tools. d = 0 for destination W d Destination select; d = 0: store result in W, d = 1 for destination f d = 1: store result in file register f. f = 7-bit file register address Default is d = 1 label Label name Bit-oriented file register operations TOS Top of Stack 13 10 9 7 6 0 PC Program Counter OPCODE b (BIT #) f (FILE #) PCLATH Program Counter High Latch GIE Global Interrupt Enable bit b = 3-bit bit address f = 7-bit file register address WDT Watchdog Timer/Counter TO Time-out bit Literal and control operations PD Power-down bit dest Destination either the W register or the specified General register file location 13 8 7 0 [ ] Options OPCODE k (literal) ( ) Contents  Assigned to k = 8-bit immediate value < > Register bit field CALL and GOTO instructions only  In the set of 13 11 10 0 italics User defined term (font is courier) OPCODE k (literal) k = 11-bit immediate value  1996-2013 Microchip Technology Inc. DS30430D-page 55

PIC16F8X TABLE 9-2 PIC16FXX INSTRUCTION SET Mnemonic, Description Cycles 14-Bit Opcode Status Notes Operands Affected MSb LSb BYTE-ORIENTED FILE REGISTER OPERATIONS ADDWF f, d Add W and f 1 00 0111 dfff ffff C,DC,Z 1,2 ANDWF f, d AND W with f 1 00 0101 dfff ffff Z 1,2 CLRF f Clear f 1 00 0001 lfff ffff Z 2 CLRW - Clear W 1 00 0001 0xxx xxxx Z COMF f, d Complement f 1 00 1001 dfff ffff Z 1,2 DECF f, d Decrement f 1 00 0011 dfff ffff Z 1,2 DECFSZ f, d Decrement f, Skip if 0 1(2) 00 1011 dfff ffff 1,2,3 INCF f, d Increment f 1 00 1010 dfff ffff Z 1,2 INCFSZ f, d Increment f, Skip if 0 1(2) 00 1111 dfff ffff 1,2,3 IORWF f, d Inclusive OR W with f 1 00 0100 dfff ffff Z 1,2 MOVF f, d Move f 1 00 1000 dfff ffff Z 1,2 MOVWF f Move W to f 1 00 0000 lfff ffff NOP - No Operation 1 00 0000 0xx0 0000 RLF f, d Rotate Left f through Carry 1 00 1101 dfff ffff C 1,2 RRF f, d Rotate Right f through Carry 1 00 1100 dfff ffff C 1,2 SUBWF f, d Subtract W from f 1 00 0010 dfff ffff C,DC,Z 1,2 SWAPF f, d Swap nibbles in f 1 00 1110 dfff ffff 1,2 XORWF f, d Exclusive OR W with f 1 00 0110 dfff ffff Z 1,2 BIT-ORIENTED FILE REGISTER OPERATIONS BCF f, b Bit Clear f 1 01 00bb bfff ffff 1,2 BSF f, b Bit Set f 1 01 01bb bfff ffff 1,2 BTFSC f, b Bit Test f, Skip if Clear 1 (2) 01 10bb bfff ffff 3 BTFSS f, b Bit Test f, Skip if Set 1 (2) 01 11bb bfff ffff 3 LITERAL AND CONTROL OPERATIONS ADDLW k Add literal and W 1 11 111x kkkk kkkk C,DC,Z ANDLW k AND literal with W 1 11 1001 kkkk kkkk Z CALL k Call subroutine 2 10 0kkk kkkk kkkk CLRWDT - Clear Watchdog Timer 1 00 0000 0110 0100 TO,PD GOTO k Go to address 2 10 1kkk kkkk kkkk IORLW k Inclusive OR literal with W 1 11 1000 kkkk kkkk Z MOVLW k Move literal to W 1 11 00xx kkkk kkkk RETFIE - Return from interrupt 2 00 0000 0000 1001 RETLW k Return with literal in W 2 11 01xx kkkk kkkk RETURN - Return from Subroutine 2 00 0000 0000 1000 SLEEP - Go into standby mode 1 00 0000 0110 0011 TO,PD SUBLW k Subtract W from literal 1 11 110x kkkk kkkk C,DC,Z XORLW k Exclusive OR literal with W 1 11 1010 kkkk kkkk Z Note 1: When an I/O register is modified as a function of itself ( e.g., MOVF PORTB, 1), the value used will be that value present on the pins themselves. For example, if the data latch is '1' for a pin configured as input and is driven low by an external device, the data will be written back with a '0'. 2: If this instruction is executed on the TMR0 register (and, where applicable, d = 1), the prescaler will be cleared if assigned to the Timer0 Module. 3: If Program Counter (PC) is modified or a conditional test is true, the instruction requires two cycles. The second cycle is executed as a NOP. DS30430D-page 56  1996-2013 Microchip Technology Inc.

PIC16F8X 9.1 Instruction Descriptions ADDLW Add Literal and W ANDLW AND Literal with W Syntax: [label] ADDLW k Syntax: [label] ANDLW k Operands: 0  k  255 Operands: 0  k  255 Operation: (W) + k  (W) Operation: (W) .AND. (k)  (W) Status Affected: C, DC, Z Status Affected: Z Encoding: 11 111x kkkk kkkk Encoding: 11 1001 kkkk kkkk Description: The contents of the W register are Description: The contents of W register are added to the eight bit literal 'k' and the AND’ed with the eight bit literal 'k'. The result is placed in the W register. result is placed in the W register. Words: 1 Words: 1 Cycles: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read Process Write to Decode Read Process Write to literal 'k' data W literal "k" data W Example: ADDLW 0x15 Example ANDLW 0x5F Before Instruction Before Instruction W = 0x10 W = 0xA3 After Instruction After Instruction W = 0x25 W = 0x03 ADDWF Add W and f ANDWF AND W with f Syntax: [label] ADDWF f,d Syntax: [label] ANDWF f,d Operands: 0  f  127 Operands: 0  f  127 d  d  Operation: (W) + (f)  (destination) Operation: (W) .AND. (f)  (destination) Status Affected: C, DC, Z Status Affected: Z Encoding: 00 0111 dfff ffff Encoding: 00 0101 dfff ffff Description: Add the contents of the W register with Description: AND the W register with register 'f'. If 'd' register 'f'. If 'd' is 0 the result is stored is 0 the result is stored in the W regis- in the W register. If 'd' is 1 the result is ter. If 'd' is 1 the result is stored back in stored back in register 'f'. register 'f'. Words: 1 Words: 1 Cycles: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read Process Write to Decode Read Process Write to register data destination register data destination 'f' 'f' Example ADDWF FSR, 0 Example ANDWF FSR, 1 Before Instruction Before Instruction W = 0x17 W = 0x17 FSR= 0xC2 FSR= 0xC2 After Instruction After Instruction W = 0xD9 W = 0x17 FSR= 0xC2 FSR= 0x02  1996-2013 Microchip Technology Inc. DS30430D-page 57

PIC16F8X BCF Bit Clear f BTFSC Bit Test, Skip if Clear Syntax: [label] BCF f,b Syntax: [label] BTFSC f,b Operands: 0  f  127 Operands: 0  f  127 0  b  7 0  b  7 Operation: 0  (f<b>) Operation: skip if (f<b>) = 0 Status Affected: None Status Affected: None Encoding: 01 00bb bfff ffff Encoding: 01 10bb bfff ffff Description: Bit 'b' in register 'f' is cleared. Description: If bit 'b' in register 'f' is '1' then the next instruction is executed. Words: 1 If bit 'b', in register 'f', is '0' then the next Cycles: 1 instruction is discarded, and a NOP is executed instead, making this a 2TCY Q Cycle Activity: Q1 Q2 Q3 Q4 instruction. Decode Read Process Write Words: 1 register data register 'f' 'f' Cycles: 1(2) Q Cycle Activity: Q1 Q2 Q3 Q4 Example BCF FLAG_REG, 7 Decode Read Process No-Operat Before Instruction register 'f' data ion FLAG_REG = 0xC7 After Instruction If Skip: (2nd Cycle) FLAG_REG = 0x47 Q1 Q2 Q3 Q4 No-Operati No-Opera No-Operat No-Operat on tion ion ion Example HERE BTFSC FLAG,1 FALSE GOTO PROCESS_CODE TRUE (cid:129) (cid:129) (cid:129) Before Instruction PC = address HERE After Instruction BSF Bit Set f if FLAG<1> = 0, PC = address TRUE Syntax: [label] BSF f,b if FLAG<1>=1, Operands: 0  f  127 PC = address FALSE 0  b  7 Operation: 1  (f<b>) Status Affected: None Encoding: 01 01bb bfff ffff Description: Bit 'b' in register 'f' is set. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read Process Write register data register 'f' 'f' Example BSF FLAG_REG, 7 Before Instruction FLAG_REG = 0x0A After Instruction FLAG_REG = 0x8A DS30430D-page 58  1996-2013 Microchip Technology Inc.

PIC16F8X BTFSS Bit Test f, Skip if Set CALL Call Subroutine Syntax: [label] BTFSS f,b Syntax: [ label ] CALL k Operands: 0  f  127 Operands: 0  k  2047 0  b < 7 Operation: (PC)+ 1 TOS, Operation: skip if (f<b>) = 1 k  PC<10:0>, Status Affected: None (PCLATH<4:3>)  PC<12:11> Encoding: 01 11bb bfff ffff Status Affected: None Description: If bit 'b' in register 'f' is '0' then the next Encoding: 10 0kkk kkkk kkkk instruction is executed. Description: Call Subroutine. First, return address If bit 'b' is '1', then the next instruction is (PC+1) is pushed onto the stack. The discarded and a NOP is executed eleven bit immediate address is loaded instead, making this a 2TCY instruction. into PC bits <10:0>. The upper bits of Words: 1 the PC are loaded from PCLATH. CALL is a two cycle instruction. Cycles: 1(2) Words: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Cycles: 2 Decode Read Process No-Operat Q Cycle Activity: Q1 Q2 Q3 Q4 register 'f' data ion 1st Cycle Decode Read Process Write to If Skip: (2nd Cycle) literal 'k', data PC Q1 Q2 Q3 Q4 Push PC to Stack No-Operati No-Opera No-Operat 2nd Cycle No-Opera No-Opera No-Operat No-Operat on tion ion No-Opera tion tion ion ion tion Example HERE BTFSC FLAG,1 Example HERE CALL THERE FALSE GOTO PROCESS_CODE TRUE (cid:129) Before Instruction (cid:129) PC = Address HERE (cid:129) After Instruction Before Instruction PC = Address THERE TOS= Address HERE+1 PC = address HERE After Instruction if FLAG<1> = 0, PC = address FALSE if FLAG<1> = 1, PC = address TRUE  1996-2013 Microchip Technology Inc. DS30430D-page 59

PIC16F8X CLRF Clear f CLRW Clear W Syntax: [label] CLRF f Syntax: [ label ] CLRW Operands: 0  f  127 Operands: None Operation: 00h  (f) Operation: 00h  (W) 1  Z 1  Z Status Affected: Z Status Affected: Z Encoding: 00 0001 1fff ffff Encoding: 00 0001 0xxx xxxx Description: The contents of register 'f' are cleared Description: W register is cleared. Zero bit (Z) is and the Z bit is set. set. Words: 1 Words: 1 Cycles: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read Process Write Decode No-Opera Process Write to register data register 'f' tion data W 'f' Example CLRW Example CLRF FLAG_REG Before Instruction Before Instruction W = 0x5A FLAG_REG = 0x5A After Instruction After Instruction W = 0x00 FLAG_REG = 0x00 Z = 1 Z = 1 CLRWDT Clear Watchdog Timer Syntax: [ label ] CLRWDT Operands: None Operation: 00h  WDT 0  WDT prescaler, 1  TO 1  PD Status Affected: TO, PD Encoding: 00 0000 0110 0100 Description: CLRWDT instruction resets the Watch- dog Timer. It also resets the prescaler of the WDT. Status bits TO and PD are set. Words: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode No-Opera Process Clear tion data WDT Counter Example CLRWDT Before Instruction WDT counter = ? After Instruction WDT counter = 0x00 WDT prescaler= 0 TO = 1 PD = 1 DS30430D-page 60  1996-2013 Microchip Technology Inc.

PIC16F8X COMF Complement f DECFSZ Decrement f, Skip if 0 Syntax: [ label ] COMF f,d Syntax: [ label ] DECFSZ f,d Operands: 0  f  127 Operands: 0  f  127 d  [0,1] d  [0,1] Operation: (f)  (destination) Operation: (f) - 1  (destination); Status Affected: Z skip if result = 0 Encoding: 00 1001 dfff ffff Status Affected: None Description: The contents of register 'f' are comple- Encoding: 00 1011 dfff ffff mented. If 'd' is 0 the result is stored in W. If 'd' is 1 the result is stored back in Description: The contents of register 'f' are decre- register 'f'. mented. If 'd' is 0 the result is placed in the W register. If 'd' is 1 the result is placed Words: 1 back in register 'f'. If the result is 1, the next instruction, is Cycles: 1 executed. If the result is 0, then a NOP is executed instead making it a 2TCY instruc- Q Cycle Activity: Q1 Q2 Q3 Q4 tion. Decode Read Process Write to Words: 1 register data destination 'f' Cycles: 1(2) Q Cycle Activity: Q1 Q2 Q3 Q4 Example COMF REG1,0 Decode Read Process Write to Before Instruction register 'f' data destination REG1 = 0x13 If Skip: (2nd Cycle) After Instruction Q1 Q2 Q3 Q4 REG1 = 0x13 W = 0xEC No-Opera No-Operat No-Operati No-Operat tion ion on ion DECF Decrement f Syntax: [label] DECF f,d Example HERE DECFSZ CNT, 1 Operands: 0  f  127 GOTO LOOP d  [0,1] CONTINUE (cid:129) (cid:129) Operation: (f) - 1  (destination) (cid:129) Status Affected: Z Before Instruction PC = address HERE Encoding: 00 0011 dfff ffff After Instruction Description: Decrement register 'f'. If 'd' is 0 the CNT = CNT - 1 result is stored in the W register. If 'd' is if CNT= 0, 1 the result is stored back in register 'f'. PC = address CONTINUE Words: 1 if CNT 0, PC = address HERE+1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read Process Write to register data destination 'f' Example DECF CNT, 1 Before Instruction CNT = 0x01 Z = 0 After Instruction CNT = 0x00 Z = 1  1996-2013 Microchip Technology Inc. DS30430D-page 61

PIC16F8X GOTO Unconditional Branch INCF Increment f Syntax: [ label ] GOTO k Syntax: [ label ] INCF f,d Operands: 0  k  2047 Operands: 0  f  127 d  [0,1] Operation: k  PC<10:0> PCLATH<4:3>  PC<12:11> Operation: (f) + 1  (destination) Status Affected: None Status Affected: Z Encoding: 10 1kkk kkkk kkkk Encoding: 00 1010 dfff ffff Description: GOTO is an unconditional branch. The Description: The contents of register 'f' are incre- eleven bit immediate value is loaded mented. If 'd' is 0 the result is placed in into PC bits <10:0>. The upper bits of the W register. If 'd' is 1 the result is PC are loaded from PCLATH<4:3>. placed back in register 'f'. GOTO is a two cycle instruction. Words: 1 Words: 1 Cycles: 1 Cycles: 2 Q Cycle Activity: Q1 Q2 Q3 Q4 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read Process Write to 1st Cycle Decode Read Process Write to register data destination literal 'k' data PC 'f' 2nd Cycle No-Operat No-Opera No-Operat No-Operat ion tion ion ion Example INCF CNT, 1 Before Instruction Example GOTO THERE CNT = 0xFF Z = 0 After Instruction After Instruction PC = Address THERE CNT = 0x00 Z = 1 DS30430D-page 62  1996-2013 Microchip Technology Inc.

PIC16F8X INCFSZ Increment f, Skip if 0 IORLW Inclusive OR Literal with W Syntax: [ label ] INCFSZ f,d Syntax: [ label ] IORLW k Operands: 0  f  127 Operands: 0  k  255 d  [0,1] Operation: (W) .OR. k  (W) Operation: (f) + 1  (destination), Status Affected: Z skip if result = 0 Encoding: 11 1000 kkkk kkkk Status Affected: None Description: The contents of the W register is Encoding: 00 1111 dfff ffff OR’ed with the eight bit literal 'k'. The Description: The contents of register 'f' are incre- result is placed in the W register. mented. If 'd' is 0 the result is placed in Words: 1 the W register. If 'd' is 1 the result is placed back in register 'f'. Cycles: 1 If the result is 1, the next instruction is executed. If the result is 0, a NOP is exe- Q Cycle Activity: Q1 Q2 Q3 Q4 cuted instead making it a 2TCY instruc- tion. Decode Read Process Write to Words: 1 literal 'k' data W Cycles: 1(2) Example IORLW 0x35 Q Cycle Activity: Q1 Q2 Q3 Q4 Before Instruction Decode Read Process Write to W = 0x9A register 'f' data destination After Instruction If Skip: (2nd Cycle) W = 0xBF Z = 1 Q1 Q2 Q3 Q4 No-Opera No-Opera No-Operati No-Operat tion tion on ion Example HERE INCFSZ CNT, 1 GOTO LOOP CONTINUE (cid:129) (cid:129) (cid:129) Before Instruction PC = address HERE After Instruction CNT = CNT + 1 if CNT= 0, PC = address CONTINUE if CNT 0, PC = address HERE +1  1996-2013 Microchip Technology Inc. DS30430D-page 63

PIC16F8X IORWF Inclusive OR W with f MOVLW Move Literal to W Syntax: [ label ] IORWF f,d Syntax: [ label ] MOVLW k Operands: 0  f  127 Operands: 0  k  255 d  [0,1] Operation: k  (W) Operation: (W) .OR. (f)  (destination) Status Affected: None Status Affected: Z Encoding: 11 00xx kkkk kkkk Encoding: 00 0100 dfff ffff Description: The eight bit literal 'k' is loaded into W Description: Inclusive OR the W register with regis- register. The don’t cares will assemble ter 'f'. If 'd' is 0 the result is placed in the as 0’s. W register. If 'd' is 1 the result is placed back in register 'f'. Words: 1 Words: 1 Cycles: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read Process Write to literal 'k' data W Decode Read Process Write to register data destination 'f' Example MOVLW 0x5A After Instruction Example IORWF RESULT, 0 W = 0x5A Before Instruction RESULT = 0x13 W = 0x91 After Instruction RESULT = 0x13 W = 0x93 Z = 1 MOVWF Move W to f MOVF Move f Syntax: [ label ] MOVWF f Syntax: [ label ] MOVF f,d Operands: 0  f  127 Operands: 0  f  127 d  [0,1] Operation: (W)  (f) Operation: (f)  (destination) Status Affected: None Status Affected: Z Encoding: 00 0000 1fff ffff Encoding: 00 1000 dfff ffff Description: Move data from W register to register 'f'. Description: The contents of register f is moved to a destination dependant upon the status Words: 1 of d. If d = 0, destination is W register. If Cycles: 1 d = 1, the destination is file register f itself. d = 1 is useful to test a file regis- Q Cycle Activity: Q1 Q2 Q3 Q4 ter since status flag Z is affected. Decode Read Process Write Words: 1 register data register 'f' 'f' Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Example MOVWF OPTION_REG Decode Read Process Write to Before Instruction register data destination OPTION = 0xFF 'f' W = 0x4F After Instruction Example MOVF FSR, 0 OPTION = 0x4F After Instruction W = 0x4F W = value in FSR register Z = 1 DS30430D-page 64  1996-2013 Microchip Technology Inc.

PIC16F8X NOP No Operation RETFIE Return from Interrupt Syntax: [ label ] NOP Syntax: [ label ] RETFIE Operands: None Operands: None Operation: No operation Operation: TOS  PC, 1  GIE Status Affected: None Status Affected: None Encoding: 00 0000 0xx0 0000 Encoding: 00 0000 0000 1001 Description: No operation. Description: Return from Interrupt. Stack is POPed Words: 1 and Top of Stack (TOS) is loaded in the Cycles: 1 PC. Interrupts are enabled by setting Global Interrupt Enable bit, GIE Q Cycle Activity: Q1 Q2 Q3 Q4 (INTCON<7>). This is a two cycle Decode No-Opera No-Opera No-Operat instruction. tion tion ion Words: 1 Example NOP Cycles: 2 Q Cycle Activity: Q1 Q2 Q3 Q4 1st Cycle Decode No-Opera Set the Pop from tion GIE bit the Stack 2nd Cycle No-Opera No-Opera No-Operat No-Operat tion tion ion ion Example RETFIE After Interrupt PC = TOS GIE = 1 OPTION Load Option Register Syntax: [ label ] OPTION Operands: None Operation: (W)  OPTION Status Affected: None Encoding: 00 0000 0110 0010 Description: The contents of the W register are loaded in the OPTION register. This instruction is supported for code com- patibility with PIC16C5X products. Since OPTION is a readable/writable register, the user can directly address it. Words: 1 Cycles: 1 Example To maintain upward compatibility with future PIC16CXX products, do not use this instruction.  1996-2013 Microchip Technology Inc. DS30430D-page 65

PIC16F8X RETLW Return with Literal in W RETURN Return from Subroutine Syntax: [ label ] RETLW k Syntax: [ label ] RETURN Operands: 0  k  255 Operands: None Operation: k  (W); Operation: TOS  PC TOS  PC Status Affected: None Status Affected: None Encoding: 00 0000 0000 1000 Encoding: 11 01xx kkkk kkkk Description: Return from subroutine. The stack is Description: The W register is loaded with the eight POPed and the top of the stack (TOS) bit literal 'k'. The program counter is is loaded into the program counter. This loaded from the top of the stack (the is a two cycle instruction. return address). This is a two cycle Words: 1 instruction. Cycles: 2 Words: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Cycles: 2 1st Cycle Decode No-Opera No-Opera Pop from Q Cycle Activity: Q1 Q2 Q3 Q4 tion tion the Stack 1st Cycle Decode Read No-Opera Write to 2nd Cycle No-Opera No-Opera No-Opera literal 'k' tion W, Pop No-Operat tion tion tion from the ion Stack 2nd Cycle No-Opera No-Opera No-Operat Example RETURN No-Operat tion tion ion ion After Interrupt PC = TOS Example CALL TABLE ;W contains table ;offset value (cid:129) ;W now has table value (cid:129) (cid:129) TABLE ADDWF PC ;W = offset RETLW k1 ;Begin table RETLW k2 ; (cid:129) (cid:129) (cid:129) RETLW kn ; End of table Before Instruction W = 0x07 After Instruction W = value of k8 DS30430D-page 66  1996-2013 Microchip Technology Inc.

PIC16F8X RLF Rotate Left f through Carry RRF Rotate Right f through Carry Syntax: [ label ] RLF f,d Syntax: [ label ] RRF f,d Operands: 0  f  127 Operands: 0  f  127 d  [0,1] d  [0,1] Operation: See description below Operation: See description below Status Affected: C Status Affected: C Encoding: 00 1101 dfff ffff Encoding: 00 1100 dfff ffff Description: The contents of register 'f' are rotated Description: The contents of register 'f' are rotated one bit to the left through the Carry one bit to the right through the Carry Flag. If 'd' is 0 the result is placed in the Flag. If 'd' is 0 the result is placed in the W register. If 'd' is 1 the result is stored W register. If 'd' is 1 the result is placed back in register 'f'. back in register 'f'. C Register f C Register f Words: 1 Words: 1 Cycles: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read Process Write to Decode Read Process Write to register data destination register data destination 'f' 'f' Example RLF REG1,0 Example RRF REG1,0 Before Instruction Before Instruction REG1 = 1110 0110 REG1 = 1110 0110 C = 0 C = 0 After Instruction After Instruction REG1 = 1110 0110 REG1 = 1110 0110 W = 1100 1100 W = 0111 0011 C = 1 C = 0  1996-2013 Microchip Technology Inc. DS30430D-page 67

PIC16F8X SLEEP SUBLW Subtract W from Literal Syntax: [ label ] SLEEP Syntax: [ label ] SUBLW k Operands: None Operands: 0 k 255 Operation: 00h  WDT, Operation: k - (W) W) 0  WDT prescaler, Status Affected: C, DC, Z 1  TO, Encoding: 11 110x kkkk kkkk 0  PD Description: The W register is subtracted (2’s comple- Status Affected: TO, PD ment method) from the eight bit literal 'k'. Encoding: 00 0000 0110 0011 The result is placed in the W register. Description: The power-down status bit, PD is Words: 1 cleared. Time-out status bit, TO is Cycles: 1 set. Watchdog Timer and its pres- caler are cleared. Q Cycle Activity: Q1 Q2 Q3 Q4 The processor is put into SLEEP Decode Read Process Write to W mode with the oscillator stopped. See literal 'k' data Section14.8 for more details. Words: 1 Example 1: SUBLW 0x02 Cycles: 1 Before Instruction Q Cycle Activity: Q1 Q2 Q3 Q4 W = 1 C = ? Decode No-Opera No-Opera Go to tion tion Sleep Z = ? After Instruction Example: SLEEP W = 1 C = 1; result is positive Z = 0 Example 2: Before Instruction W = 2 C = ? Z = ? After Instruction W = 0 C = 1; result is zero Z = 1 Example 3: Before Instruction W = 3 C = ? Z = ? After Instruction W = 0xFF C = 0; result is negative Z = 0 DS30430D-page 68  1996-2013 Microchip Technology Inc.

PIC16F8X SUBWF Subtract W from f SWAPF Swap Nibbles in f Syntax: [ label ] SUBWF f,d Syntax: [ label ] SWAPF f,d Operands: 0 f 127 Operands: 0  f  127 d  [0,1] d  [0,1] Operation: (f) - (W) destination) Operation: (f<3:0>)  (destination<7:4>), (f<7:4>)  (destination<3:0>) Status Affected: C, DC, Z Status Affected: None Encoding: 00 0010 dfff ffff Encoding: 00 1110 dfff ffff Description: Subtract (2’s complement method) W reg- ister from register 'f'. If 'd' is 0 the result is Description: The upper and lower nibbles of register stored in the W register. If 'd' is 1 the 'f' are exchanged. If 'd' is 0 the result is result is stored back in register 'f'. placed in W register. If 'd' is 1 the result is placed in register 'f'. Words: 1 Words: 1 Cycles: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read Process Write to register 'f' data destination Decode Read Process Write to register 'f' data destination Example 1: SUBWF REG1,1 Example SWAPF REG, 0 Before Instruction Before Instruction REG1 = 3 W = 2 REG1 = 0xA5 C = ? After Instruction Z = ? REG1 = 0xA5 After Instruction W = 0x5A REG1 = 1 W = 2 C = 1; result is positive Z = 0 Example 2: Before Instruction TRIS Load TRIS Register REG1 = 2 Syntax: [label] TRIS f W = 2 Operands: 5  f  7 C = ? Z = ? Operation: (W)  TRIS register f; After Instruction Status Affected: None Encoding: 00 0000 0110 0fff REG1 = 0 W = 2 Description: The instruction is supported for code C = 1; result is zero compatibility with the PIC16C5X prod- Z = 1 ucts. Since TRIS registers are read- Example 3: Before Instruction able and writable, the user can directly address them. REG1 = 1 Words: 1 W = 2 C = ? Cycles: 1 Z = ? Example After Instruction To maintain upward compatibility REG1 = 0xFF with future PIC16CXX products, W = 2 do not use this instruction. C = 0; result is negative Z = 0  1996-2013 Microchip Technology Inc. DS30430D-page 69

PIC16F8X XORLW Exclusive OR Literal with W XORWF Exclusive OR W with f Syntax: [label] XORLW k Syntax: [label] XORWF f,d Operands: 0 k 255 Operands: 0  f  127 d  [0,1] Operation: (W) .XOR. k W) Operation: (W) .XOR. (f) destination) Status Affected: Z Status Affected: Z Encoding: 11 1010 kkkk kkkk Encoding: 00 0110 dfff ffff Description: The contents of the W register are XOR’ed with the eight bit literal 'k'. Description: Exclusive OR the contents of the W The result is placed in the W regis- register with register 'f'. If 'd' is 0 the ter. result is stored in the W register. If 'd' is 1 the result is stored back in register 'f'. Words: 1 Words: 1 Cycles: 1 Cycles: 1 Q Cycle Activity: Q1 Q2 Q3 Q4 Q Cycle Activity: Q1 Q2 Q3 Q4 Decode Read Process Write to literal 'k' data W Decode Read Process Write to register data destination 'f' Example: XORLW 0xAF Before Instruction Example XORWF REG 1 W = 0xB5 Before Instruction After Instruction REG = 0xAF W = 0xB5 W = 0x1A After Instruction REG = 0x1A W = 0xB5 DS30430D-page 70  1996-2013 Microchip Technology Inc.

PIC16F8X 10.0 DEVELOPMENT SUPPORT 10.3 ICEPIC: Low-Cost PIC MCU In-Circuit Emulator 10.1 Development Tools ICEPIC is a low-cost in-circuit emulator solution for the The PIC® microcontrollers are supported with a full Microchip PIC12CXXX, PIC16C5X and PIC16CXXX range of hardware and software development tools: families of 8-bit OTP microcontrollers. (cid:129) PICMASTER/PICMASTER CEReal-Time ICEPIC is designed to operate on PC-compatible In-Circuit Emulator machines ranging from 286-AT through Pentium (cid:129) ICEPIC Low-Cost PIC16C5X and PIC16CXXX based machines under Windows 3.x environment. ICE- In-Circuit Emulator PIC features real time, non-intrusive emulation. (cid:129) PRO MATE II Universal Programmer 10.4 PRO MATE II: Universal Programmer (cid:129) PICSTART Plus Entry-Level Prototype Programmer The PRO MATE II Universal Programmer is a full-fea- (cid:129) PICDEM-1 Low-Cost Demonstration Board tured programmer capable of operating in stand-alone (cid:129) PICDEM-2 Low-Cost Demonstration Board mode as well as PC-hosted mode. PRO MATE II is CE compliant. (cid:129) PICDEM-3 Low-Cost Demonstration Board (cid:129) MPASM Assembler The PRO MATE II has programmable VDD and VPP supplies which allows it to verify programmed memory (cid:129) MPLABSIM Software Simulator at VDD min and VDD max for maximum reliability. It has (cid:129) MPLAB-C17 (C Compiler) an LCD display for displaying error messages, keys to (cid:129) Fuzzy Logic Development System enter commands and a modular detachable socket (fuzzyTECHMP) assembly to support various package types. In stand- alone mode the PRO MATE II can read, verify or pro- 10.2 PICMASTER: High Performance gram PIC12CXXX, PIC14C000, PIC16C5X, Universal In-Circuit Emulator with PIC16CXXX and PIC17CXX devices. It can also set MPLAB IDE configuration and code-protect bits in this mode. The PICMASTER Universal In-Circuit Emulator is 10.5 PICSTART Plus Entry Level intended to provide the product development engineer Development System with a complete microcontroller design tool set for all microcontrollers in the PIC14C000, PIC12CXXX, The PICSTART programmer is an easy-to-use, PIC16C5X, PIC16CXXX and PIC17CXX families. low-cost prototype programmer. It connects to the PC PICMASTER is supplied with the MPLAB Integrated via one of the COM (RS-232) ports. MPLAB Integrated Development Environment (IDE), which allows editing, Development Environment software makes using the “make” and download, and source debugging from a programmer simple and efficient. PICSTART Plus is not single environment. recommended for production programming. Interchangeable target probes allow the system to be PICSTART Plus supports all PIC12CXXX, PIC14C000, easily reconfigured for emulation of different proces- PIC16C5X, PIC16CXXX and PIC17CXX devices with sors. The universal architecture of the PICMASTER up to 40 pins. Larger pin count devices such as the allows expansion to support all new Microchip micro- PIC16C923, PIC16C924 and PIC17C756 may be sup- controllers. ported with an adapter socket. PICSTART Plus is CE The PICMASTER Emulator System has been designed compliant. as a real-time emulation system with advanced fea- tures that are generally found on more expensive devel- opment tools. The PC compatible 386 (and higher) machine platform and Microsoft Windows 3.x environ- ment were chosen to best make these features avail- able to you, the end user. A CE compliant version of PICMASTER is available for European Union (EU) countries.  1996-2013 Microchip Technology Inc. DS30430D-page 71

PIC16F8X 10.6 PICDEM-1 Low-Cost PIC MCU an RS-232 interface, push-button switches, a potenti- Demonstration Board ometer for simulated analog input, a thermistor and separate headers for connection to an external LCD The PICDEM-1 is a simple board which demonstrates module and a keypad. Also provided on the PICDEM-3 the capabilities of several of Microchip’s microcon- board is an LCD panel, with 4 commons and 12 seg- trollers. The microcontrollers supported are: PIC16C5X ments, that is capable of displaying time, temperature (PIC16C54 to PIC16C58A), PIC16C61, PIC16C62X, and day of the week. The PICDEM-3 provides an addi- PIC16C71, PIC16C8X, PIC17C42, PIC17C43 and tional RS-232 interface and Windows 3.1 software for PIC17C44. All necessary hardware and software is showing the demultiplexed LCD signals on a PC. A sim- included to run basic demo programs. The users can ple serial interface allows the user to construct a hard- program the sample microcontrollers provided with ware demultiplexer for the LCD signals. the PICDEM-1 board, on a PROMATE II or PICSTART-Plus programmer, and easily test firm- 10.9 MPLAB™ Integrated Development ware. The user can also connect the PICDEM-1 Environment Software board to the PICMASTER emulator and download The MPLAB IDE Software brings an ease of software the firmware to the emulator for testing. Additional pro- development previously unseen in the 8-bit microcon- totype area is available for the user to build some addi- troller market. MPLAB is a windows based application tional hardware and connect it to the microcontroller which contains: socket(s). Some of the features include an RS-232 interface, a potentiometer for simulated analog input, (cid:129) A full featured editor push-button switches and eight LEDs connected to (cid:129) Three operating modes PORTB. - editor - emulator 10.7 PICDEM-2 Low-Cost PIC16CXX - simulator Demonstration Board (cid:129) A project manager (cid:129) Customizable tool bar and key mapping The PICDEM-2 is a simple demonstration board that (cid:129) A status bar with project information supports the PIC16C62, PIC16C64, PIC16C65, (cid:129) Extensive on-line help PIC16C73 and PIC16C74 microcontrollers. All the necessary hardware and software is included to MPLAB allows you to: run the basic demonstration programs. The user (cid:129) Edit your source files (either assembly or ‘C’) can program the sample microcontrollers provided (cid:129) One touch assemble (or compile) and download with the PICDEM-2 board, on a PRO MATE II pro- to PIC MCU tools (automatically updates all proj- grammer or PICSTART-Plus, and easily test firmware. ect information) The PICMASTER emulator may also be used with the (cid:129) Debug using: PICDEM-2 board to test firmware. Additional prototype - source files area has been provided to the user for adding addi- - absolute listing file tional hardware and connecting it to the microcontroller (cid:129) Transfer data dynamically via DDE (soon to be socket(s). Some of the features include a RS-232 inter- replaced by OLE) face, push-button switches, a potentiometer for simu- (cid:129) Run up to four emulators on the same PC lated analog input, a Serial EEPROM to demonstrate usage of the I2C bus and separate headers for connec- The ability to use MPLAB with Microchip’s simulator allows a consistent platform and the ability to easily tion to an LCD module and a keypad. switch from the low cost simulator to the full featured 10.8 PICDEM-3 Low-Cost PIC16CXXX emulator with minimal retraining due to development Demonstration Board tools. 10.10 Assembler (MPASM) The PICDEM-3 is a simple demonstration board that supports the PIC16C923 and PIC16C924 in the PLCC The MPASM Universal Macro Assembler is a package. It will also support future 44-pin PLCC PC-hosted symbolic assembler. It supports all micro- microcontrollers with a LCD Module. All the neces- controller series including the PIC12C5XX, PIC14000, sary hardware and software is included to run the PIC16C5X, PIC16CXXX, and PIC17CXX families. basic demonstration programs. The user can pro- gram the sample microcontrollers provided with MPASM offers full featured Macro capabilities, condi- the PICDEM-3 board, on a PRO MATE II program- tional assembly, and several source and listing formats. mer or PICSTART Plus with an adapter socket, and It generates various object code formats to support easily test firmware. The PICMASTER emulator may Microchip's development tools as well as third party also be used with the PICDEM-3 board to test firm- programmers. ware. Additional prototype area has been provided to MPASM allows full symbolic debugging from the user for adding hardware and connecting it to the PICMASTER, Microchip’s Universal Emulator System. microcontroller socket(s). Some of the features include DS30430D-page 72  1996-2013 Microchip Technology Inc.

PIC16F8X MPASM has the following features to assist in develop- 10.14 MP-DriveWay – Application Code ing software for specific use applications. Generator (cid:129) Provides translation of Assembler source code to MP-DriveWay is an easy-to-use Windows-based Appli- object code for all Microchip microcontrollers. cation Code Generator. With MP-DriveWay you can (cid:129) Macro assembly capability. visually configure all the peripherals in a PIC device (cid:129) Produces all the files (Object, Listing, Symbol, and, with a click of the mouse, generate all the initial- and special) required for symbolic debug with ization and many functional code modules in C lan- Microchip’s emulator systems. guage. The output is fully compatible with Microchip’s (cid:129) Supports Hex (default), Decimal and Octal source MPLAB-C C compiler. The code produced is highly and listing formats. modular and allows easy integration of your own code. MP-DriveWay is intelligent enough to maintain your MPASM provides a rich directive language to support code through subsequent code generation. programming of the PIC MCU. Directives are helpful in making the development of your assemble source code 10.15 SEEVAL Evaluation and shorter and more maintainable. Programming System 10.11 Software Simulator (MPLAB-SIM) The SEEVAL SEEPROM Designer’s Kit supports all The MPLAB-SIM Software Simulator allows code Microchip 2-wire and 3-wire Serial EEPROMs. The kit development in a PC host environment. It allows the includes everything necessary to read, write, erase or user to simulate the PIC MCU series microcontrollers program special features of any Microchip SEEPROM on an instruction level. On any given instruction, the product including Smart Serials and secure serials. user may examine or modify any of the data areas or The Total Endurance Disk is included to aid in provide external stimulus to any of the pins. The trade-off analysis and reliability calculations. The total input/output radix can be set by the user and the exe- kit can significantly reduce time-to-market and result in cution can be performed in; single step, execute until an optimized system. break, or in a trace mode. 10.16 KEELOQ Evaluation and MPLAB-SIM fully supports symbolic debugging using Programming Tools MPLAB-C and MPASM. The Software Simulator offers the low cost flexibility to develop and debug code out- KEELOQ evaluation and programming tools support side of the laboratory environment making it an excel- Microchips HCS Secure Data Products. The HCS eval- lent multi-project software development tool. uation kit includes an LCD display to show changing codes, a decoder to decode transmissions, and a pro- 10.12 C Compiler (MPLAB-C17) gramming interface to program test transmitters. The MPLAB-C Code Development System is a complete ‘C’ compiler and integrated development environment for Microchip’s PIC17CXXX family of microcontrollers. The compiler provides powerful inte- gration capabilities and ease of use not found with other compilers. For easier source level debugging, the compiler pro- vides symbol information that is compatible with the MPLAB IDE memory display. 10.13 Fuzzy Logic Development System (fuzzyTECH-MP) fuzzyTECH-MP fuzzy logic development tool is avail- able in two versions - a low cost introductory version, MPExplorer, for designers to gain a comprehensive working knowledge of fuzzy logic system design; and a full-featured version, fuzzyTECH-MP, Edition for imple- menting more complex systems. Both versions include Microchip’s fuzzyLAB demon- stration board for hands-on experience with fuzzy logic systems implementation.  1996-2013 Microchip Technology Inc. DS30430D-page 73

PIC16F8X TABLE 10-1: DEVELOPMENT TOOLS FROM MICROCHIP 001 000 S2S3S3    CCC HHH XXX CXCXCX    453 229 X 5 7 C      7 1 C PI X 4 C 7         1 C PI X X 9 C         6 1 C PI X 8 C 6         1 C PI X X 7 C         6 1 C PI X 6 C 6         1 C PI X X X C         6 1 C PI X 5 C 6         1 C PI 0 0 0 4      1 C PI X X 5 C       2 1 C PI PICMASTER/PICMASTER-CEIn-Circuit Emulator ICEPIC Low-CostIn-Circuit Emulator MPLABIntegratedDevelopmentEnvironment MPLAB C17CompilerfuzzyTECH-MPExplorer/EditionFuzzy LogicDev. Tool MP-DriveWayApplicationsCode Generator Total EnduranceSoftware ModelPICSTARTPlus Low-CostUniversal Dev. KitPRO MATE IIUniversalProgrammerKEELOQProgrammerSEEVALDesigners Kit PICDEM-1 PICDEM-2 PICDEM-3 KEELOQEvaluation Kit stcudorP rotalumE slooT erawtfoS sremmargorP sdraoB omeD DS30430D-page 74  1996-2013 Microchip Technology Inc.

PIC16F8X PIC16F83/84 10.0 ELECTRICAL CHARACTERISTICS FOR PIC16F83 AND PIC16F84 Absolute Maximum Ratings † Ambient temperature under bias.............................................................................................................-55C to +125C Storage temperature.............................................................................................................................. -65C to +150C Voltage on VDD with respect to VSS ........................................................................................................... -0.3 to +7.5V Voltage on MCLR with respect to VSS(2).......................................................................................................-0.3 to +14V Voltage on any pin with respect to VSS (except VDD and MCLR)....................................................-0.6V to (VDD + 0.6V) Total power dissipation(1).....................................................................................................................................800 mW Maximum current out of VSS pin...........................................................................................................................150 mA Maximum current into VDD pin..............................................................................................................................100 mA Input clamp current, IIK (VI < 0 or VI > VDD)20 mA Output clamp current, IOK (VO < 0 or VO > VDD)20 mA Maximum output current sunk by any I/O pin..........................................................................................................25 mA Maximum output current sourced by any I/O pin....................................................................................................20 mA Maximum current sunk byPORTA..........................................................................................................................80 mA Maximum current sourced by PORTA.....................................................................................................................50 mA Maximum current sunk by PORTB........................................................................................................................150 mA Maximum current sourced by PORTB...................................................................................................................100 mA Note 1: Power dissipation is calculated as follows: Pdis = VDD x {IDD -  IOH} +  {(VDD-VOH) x IOH} + (VOl x IOL) Note 2: Voltage spikes below VSS at the MCLR pin, inducing currents greater than 80 mA, may cause latch-up. Thus, a series resistor of 50-100 should be used when applying a “low” level to the MCLR pin rather than pulling this pin directly to VSS. † NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability.  1996-2013 Microchip Technology Inc. DS30430D-page 11-75

PIC16F8X PIC16F83/84 TABLE 10-1 CROSS REFERENCE OF DEVICE SPECS FOR OSCILLATOR CONFIGURATIONS AND FREQUENCIES OF OPERATION (COMMERCIAL DEVICES) PIC16F84-04 PIC16F84-10 PIC16LF84-04 OSC PIC16F83-04 PIC16F83-10 PIC16LF83-04 RC VDD: 4.0V to 6.0V VDD: 4.5V to 5.5V VDD: 2.0V to 6.0V IDD: 4.5 mA max. at 5.5V IDD: 1.8 mA typ. at 5.5V IDD: 4.5 mA max. at 5.5V IPD: 14 A max. at 4V WDT dis IPD: 1.0 A typ. at 5.5V WDT dis IPD: 7.0 A max. at 2V WDT dis Freq: 4.0 MHz max. Freq: 4..0 MHz max. Freq: 2.0 MHz max. XT VDD: 4.0V to 6.0V VDD: 4.5V to 5.5V VDD: 2.0V to 6.0V IDD: 4.5 mA max. at 5.5V IDD: 1.8 mA typ. at 5.5V IDD: 4.5 mA max. at 5.5V IPD: 14 A max. at 4V WDT dis IPD: 1.0 A typ. at 5.5V WDT dis IPD: 7.0 A max. at 2V WDT dis Freq: 4.0 MHz max. Freq: 4.0 MHz max. Freq: 2.0 MHz max. HS VDD: 4.5V to 5.5V VDD: 4.5V to 5.5V IDD: 4.5 mA typ. at 5.5V IDD: 10 mA max. at 5.5V typ. Do not use in HS mode IPD: 1.0 A typ. at 4.5V WDT dis IPD: 1.0 A typ. at 4.5V WDT dis Freq: 4.0 MHz max. Freq: 10 MHz max. LP VDD: 4.0V to 6.0V VDD: 2.0V to 6.0V IDD: 48 A typ. at 32 kHz, 2.0V IDD: 45 A max. at 32 kHz, 2.0V Do not use in LP mode IPD: 0.6 A typ. at 3.0V WDT dis IPD: 7 A max. at 2.0V WDT dis Freq: 200 kHz max. Freq: 200 kHz max. The shaded sections indicate oscillator selections which are tested for functionality, but not for MIN/MAX specifica- tions. It is recommended that the user select the device type that ensures the specifications required. DS30430D-page 11-76  1996-2013 Microchip Technology Inc.

PIC16F8X PIC16F83/84 10.1 DC CHARACTERISTICS: PIC16F84, PIC16F83 (Commercial, Industrial) Standard Operating Conditions (unless otherwise stated) DC Characteristics Operating temperature 0C  TA  +70C (commercial) Power Supply Pins -40C  TA  +85C (industrial) Parameter Sym Characteristic Min Typ† Max Units Conditions No. D001 VDD Supply Voltage 4.0 — 6.0 V XT, RC and LP osc configuration D001A 4.5 — 5.5 V HS osc configuration D002 VDR RAM Data Retention 1.5* — — V Device in SLEEP mode Voltage(1) D003 VPOR VDD start voltage to — VSS — V See section on Power-on Reset for details ensure internal Power-on Reset signal D004 SVDD VDD rise rate to ensure 0.05* — — V/ms See section on Power-on Reset for details internal Power-on Reset signal IDD Supply Current(2) RC and XT osc configuration(4) D010 — 1.8 4.5 mA FOSC = 4.0 MHz, VDD = 5.5V D010A — 7.3 10 mA FOSC = 4.0 MHz, VDD = 5.5V (During Flash programming) HS osc configuration (PIC16F84-10) D013 — 5 10 mA FOSC = 10 MHz, VDD = 5.5V D020 IPD Power-down Current(3) — 7.0 28 A VDD = 4.0V, WDT enabled, industrial D021 — 1.0 14 A VDD = 4.0V, WDT disabled, commercial D021A — 1.0 16 A VDD = 4.0V, WDT disabled, industrial * These parameters are characterized but not tested. † Data in "Typ" column is at 5.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data. 2: The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin loading and switching rate, oscillator type, internal code execution pattern, and temperature also have an impact on the current consumption. The test conditions for all IDD measurements in active operation mode are: OSC1=external square wave, from rail to rail; all I/O pins tristated, pulled to VDD, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified. 3: The power down current in SLEEP mode does not depend on the oscillator type. Power-down current is measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS. 4: For RC osc configuration, current through Rext is not included. The current through the resistor can be esti- mated by the formula IR = VDD/2Rext (mA) with Rext in kOhm.  1996-2013 Microchip Technology Inc. DS30430D-page 11-77

PIC16F8X PIC16F83/84 10.2 DC CHARACTERISTICS: PIC16LF84, PIC16LF83 (Commercial, Industrial) Standard Operating Conditions (unless otherwise stated) DC Characteristics Operating temperature 0C  TA  +70C (commercial) Power Supply Pins -40C  TA  +85C (industrial) Parameter Sym Characteristic Min Typ† Max Units Conditions No. D001 VDD Supply Voltage 2.0 — 6.0 V XT, RC, and LP osc configuration D002 VDR RAM Data Retention 1.5* — — V Device in SLEEP mode Voltage(1) D003 VPOR VDD start voltage to — VSS — V See section on Power-on Reset for details ensure internal Power-on Reset signal D004 SVDD VDD rise rate to ensure 0.05* — — V/ms See section on Power-on Reset for details internal Power-on Reset signal IDD Supply Current(2) RC and XT osc configuration(4) D010 — 1 4 mA FOSC = 2.0 MHz, VDD = 5.5V D010A — 7.3 10 mA FOSC = 2.0 MHz, VDD = 5.5V (During Flash programming) LP osc configuration D014 — 15 45 A FOSC = 32 kHz, VDD = 2.0V, WDT disabled D020 IPD Power-down Current(3) — 3.0 16 A VDD = 2.0V, WDT enabled, industrial D021 — 0.4 7.0 A VDD = 2.0V, WDT disabled, commercial D021A — 0.4 9.0 A VDD = 2.0V, WDT disabled, industrial * These parameters are characterized but not tested. † Data in "Typ" column is at 5.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data. 2: The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin loading and switching rate, oscillator type, internal code execution pattern, and temperature also have an impact on the current consumption. The test conditions for all IDD measurements in active operation mode are: OSC1=external square wave, from rail to rail; all I/O pins tristated, pulled to VDD, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified. 3: The power down current in SLEEP mode does not depend on the oscillator type. Power-down current is measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS. 4: For RC osc configuration, current through Rext is not included. The current through the resistor can be estimated by the formula IR = VDD/2Rext (mA) with Rext in kOhm. DS30430D-page 11-78  1996-2013 Microchip Technology Inc.

PIC16F8X PIC16F83/84 10.3 DC CHARACTERISTICS: PIC16F84, PIC16F83 (Commercial, Industrial) PIC16LF84, PIC16LF83 (Commercial, Industrial) Standard Operating Conditions (unless otherwise stated) DC Characteristics Operating temperature 0C  TA  +70C (commercial) All Pins Except -40C  TA  +85C (industrial) Power Supply Pins Operating voltage VDD range as described in DC spec Section10.1 and Section10.2. Parame- ter No. Sym Characteristic Min Typ† Max Units Conditions Input Low Voltage VIL I/O ports D030 with TTL buffer VSS — 0.8 V 4.5 V  VDD  5.5 V(4) D030A VSS — 0.16VDD V entire range(4) D031 with Schmitt Trigger buffer VSS — 0.2VDD V entire range D032 MCLR, RA4/T0CKI Vss — 0.2VDD V D033 OSC1 (XT, HS and LP modes)(1) Vss — 0.3VDD V D034 OSC1 (RC mode) Vss — 0.1VDD V Input High Voltage VIH I/O ports — D040 with TTL buffer 2.4 — VDD V 4.5 V  VDD 5.5V(4) D040A 0.48VDD — VDD V entire range(4) D041 with Schmitt Trigger buffer 0.45VDD — VDD entire range D042 MCLR, RA4/T0CKI, OSC1 0.85 — VDD V (RC mode) VDD D043 OSC1 (XT, HS and LP modes)(1) 0.7 VDD — VDD V D050 VHYS Hysteresis of TBD — — V Schmitt Trigger inputs D070 IPURB PORTB weak pull-up current 50* 250* 400* A VDD = 5.0V, VPIN = VSS Input Leakage Current(2,3) D060 IIL I/O ports — — 1 A Vss VPIN VDD, Pin at hi-impedance D061 MCLR, RA4/T0CKI — — 5 A Vss VPIN VDD D063 OSC1 — — 5 A Vss VPIN VDD, XT, HS and LP osc configuration Output Low Voltage D080 VOL I/O ports — — 0.6 V IOL = 8.5 mA, VDD = 4.5V D083 OSC2/CLKOUT — — 0.6 V IOL = 1.6 mA, VDD = 4.5V Output High Voltage D090 VOH I/O ports(3) VDD-0.7 — — V IOH = -3.0 mA, VDD = 4.5V D092 OSC2/CLKOUT VDD-0.7 — — V IOH = -1.3 mA, VDD = 4.5V * These parameters are characterized but not tested. † Data in “Typ” column is at 5.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: In RC oscillator configuration, the OSC1 pin is a Schmitt Trigger input. Do not drive the PIC16F8X with an external clock while the device is in RC mode, or chip damage may result. 2: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified lev- els represent normal operating conditions. Higher leakage current may be measured at different input volt- ages. 3: Negative current is defined as coming out of the pin. 4: The user may choose the better of the two specs.  1996-2013 Microchip Technology Inc. DS30430D-page 11-79

PIC16F8X PIC16F83/84 10.4 DC CHARACTERISTICS: PIC16F84, PIC16F83 (Commercial, Industrial) PIC16LF84, PIC16F83 (Commercial, Industrial) Standard Operating Conditions (unless otherwise stated) DC Characteristics Operating temperature 0C  TA  +70C (commercial) All Pins Except -40C  TA  +85C (industrial) Power Supply Pins Operating voltage VDD range as described in DC spec Section10.1 and Section10.2. Parameter Sym Characteristic Min Typ† Max Units Conditions No. Capacitive Loading Specs on Output Pins D100 COSC2 OSC2 pin — — 15 pF In XT, HS and LP modes when external clock is used to drive OSC1. D101 CIO All I/O pins and OSC2 — — 50 pF (RC mode) Data EEPROM Memory D120 ED Endurance 1M 10M — E/W 25C at 5V D121 VDRW VDD for read/write VMIN — 6.0 V VMIN = Minimum operating voltage D122 TDEW Erase/Write cycle time — 10 20* ms Program Flash Memory D130 EP Endurance 100 1000 — E/W D131 VPR VDD for read VMIN — 6.0 V VMIN = Minimum operating voltage D132 VPEW VDD for erase/write 4.5 — 5.5 V D133 TPEW Erase/Write cycle time — 10 — ms * These parameters are characterized but not tested. † Data in “Typ” column is at 5.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. DS30430D-page 11-80  1996-2013 Microchip Technology Inc.

PIC16F8X PIC16F83/84 TABLE 10-2 TIMING PARAMETER SYMBOLOGY The timing parameter symbols have been created fol- lowing one of the following formats: 1. TppS2ppS 2. TppS T F Frequency T Time Lowercase symbols (pp) and their meanings: pp 2 to os,osc OSC1 ck CLKOUT ost oscillator start-up timer cy cycle time pwrt power-up timer io I/O port rbt RBx pins inp INT pin t0 T0CKI mc MCLR wdt watchdog timer Uppercase symbols and their meanings: S F Fall P Period H High R Rise I Invalid (Hi-impedance) V Valid L Low Z High Impedance FIGURE 10-1: PARAMETER MEASUREMENT INFORMATION All timings are measure between high and low mea- surement points as indicated in the figures below. 0.7 VDD XTAL (High) 0.8 VDD RC 0.9 VDD (High) 0.3 VDD XTAL 0.1 VDD (Low) (Low) 0.15 VDD RC OSC1 Measurement Points I/O Port Measurement Points FIGURE 10-2: LOAD CONDITIONS Load Condition 1 Load Condition 2 VDD/2 RL Pin CL Pin CL VSS VSS RL = 464 CL = 50 pF for all pins except OSC2. 15 pF for OSC2 output.  1996-2013 Microchip Technology Inc. DS30430D-page 11-81

PIC16F8X PIC16F83/84 10.5 Timing Diagrams and Specifications FIGURE 10-3: EXTERNAL CLOCK TIMING Q4 Q1 Q2 Q3 Q4 Q1 OSC1 1 3 3 4 4 2 CLKOUT TABLE 10-3 EXTERNAL CLOCK TIMING REQUIREMENTS Parameter No. Sym Characteristic Min Typ† Max Units Conditions (1) FOSC External CLKIN Frequency DC — 2 MHz XT, RC osc PIC16LF8X-04 DC — 4 MHz XT, RC osc PIC16F8X-04 DC — 10 MHz HS osc PIC16F8X-10 DC — 200 kHz LP osc PIC16LF8X-04 (1) Oscillator Frequency DC — 2 MHz RC osc PIC16LF8X-04 DC — 4 MHz RC osc PIC16F8X-04 0.1 — 2 MHz XT osc PIC16LF8X-04 0.1 — 4 MHz XT osc PIC16F8X-04 1.0 — 10 MHz HS osc PIC16F8X-10 DC — 200 kHz LP osc PIC16LF8X-04 (1) 1 Tosc External CLKIN Period 500 — — ns XT, RC osc PIC16LF8X-04 250 — — ns XT, RC osc PIC16F8X-04 100 — — ns HS osc PIC16F8X-10 5.0 — — s LP osc PIC16LF8X-04 (1) Oscillator Period 500 — — ns RC osc PIC16LF8X-04 250 — — ns RC osc PIC16F8X-04 500 — 10,000 ns XT osc PIC16LF8X-04 250 — 10,000 ns XT osc PIC16F8X-04 100 — 1,000 ns HS osc PIC16F8X-10 5.0 — — s LP osc PIC16LF8X-04 (1) 2 TCY Instruction Cycle Time 0.4 4/Fosc DC s 3 TosL, Clock in (OSC1) High or Low 60 * — — ns XT osc PIC16LF8X-04 TosH Time 50 * — — ns XT osc PIC16F8X-04 2.0 * — — s LP osc PIC16LF8X-04 35 * — — ns HS osc PIC16F8X-10 4 TosR, Clock in (OSC1) Rise or Fall Time 25 * — — ns XT osc PIC16F8X-04 TosF 50 * — — ns LP osc PIC16LF8X-04 15 * — — ns HS osc PIC16F8X-10 * These parameters are characterized but no tested. † Data in "Typ" column is at 5.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: Instruction cycle period (TCY) equals four times the input oscillator time-base period. All specified values are based on characterization data for that particular oscillator type under standard operating conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation and/or higher than expected current consumption. All devices are tested to operate at "min." values with an external clock applied to the OSC1 pin. When an external clock input is used, the "Max." cycle time limit is "DC" (no clock) for all devices. DS30430D-page 11-82  1996-2013 Microchip Technology Inc.

PIC16F8X PIC16F83/84 FIGURE 10-4: CLKOUT AND I/O TIMING Q4 Q1 Q2 Q3 OSC1 11 10 22 CLKOUT 23 13 12 19 18 14 16 I/O Pin (input) 17 15 I/O Pin old value new value (output) 20, 21 Note: All tests must be done with specified capacitive loads (Figure10-2) 50 pF on I/O pins and CLKOUT. TABLE 10-4 CLKOUT AND I/O TIMING REQUIREMENTS Parameter No. Sym Characteristic Min Typ† Max Units Conditions 10 TosH2ckL OSC1 to CLKOUT PIC16F8X — 15 30 * ns Note 1 10A PIC16LF8X — 15 120 * ns Note 1 11 TosH2ckH OSC1 to CLKOUT PIC16F8X — 15 30 * ns Note 1 11A PIC16LF8X — 15 120 * ns Note 1 12 TckR CLKOUT rise time PIC16F8X — 15 30 * ns Note 1 12A PIC16LF8X — 15 100 * ns Note 1 13 TckF CLKOUT fall time PIC16F8X — 15 30 * ns Note 1 13A PIC16LF8X — 15 100 * ns Note 1 14 TckL2ioV CLKOUT  to Port out valid — — 0.5TCY +20 * ns Note 1 15 TioV2ckH Port in valid before PIC16F8X 0.30TCY + 30 * — — ns Note 1 CLKOUT  PIC16LF8X 0.30TCY + 80 * — — ns Note 1 16 TckH2ioI Port in hold after CLKOUT  0 * — — ns Note 1 17 TosH2ioV OSC1 (Q1 cycle) to PIC16F8X — — 125 * ns Port out valid PIC16LF8X — — 250 * ns 18 TosH2ioI OSC1 (Q2 cycle) to PIC16F8X 10 * — — ns Port input invalid PIC16LF8X 10 * — — ns (I/O in hold time) 19 TioV2osH Port input valid to PIC16F8X -75 * — — ns OSC1 PIC16LF8X -175 * — — ns (I/O in setup time) 20 TioR Port output rise time PIC16F8X — 10 35 * ns 20A PIC16LF8X — 10 70 * ns 21 TioF Port output fall time PIC16F8X — 10 35 * ns 21A PIC16LF8X — 10 70 * ns 22 Tinp INT pin high PIC16F8X 20 * — — ns 22A or low time PIC16LF8X 55 * — — ns 23 Trbp RB7:RB4 change INT PIC16F8X TOSC § — — ns 23A high or low time PIC16LF8X TOSC § — — ns * These parameters are characterized but not tested. † Data in "Typ" column is at 5.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. § By design Note 1: Measurements are taken in RC Mode where CLKOUT output is 4 x TOSC.  1996-2013 Microchip Technology Inc. DS30430D-page 11-83

PIC16F8X PIC16F83/84 FIGURE 10-5: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER AND POWER-UP TIMER TIMING VDD MCLR 30 Internal POR 33 PWRT Time-out 32 OSC Time-out Internal RESET Watchdog Timer RESET 31 34 34 I/O Pins TABLE 10-5 RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER AND POWER-UP TIMER REQUIREMENTS Parameter No. Sym Characteristic Min Typ† Max Units Conditions 30 TmcL MCLR Pulse Width (low) 1000 * — — ns 2.0V  VDD  6.0V 31 Twdt Watchdog Timer Time-out Period 7 * 18 33 * ms VDD = 5.0V (No Prescaler) 32 Tost Oscillation Start-up Timer Period 1024TOSC ms TOSC = OSC1 period 33 Tpwrt Power-up Timer Period 28 * 72 132 * ms VDD = 5.0V 34 TIOZ I/O Hi-impedance from MCLR Low — — 100 * ns or reset * These parameters are characterized but not tested. † Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. DS30430D-page 11-84  1996-2013 Microchip Technology Inc.

PIC16F8X PIC16F83/84 FIGURE 10-6: TIMER0 CLOCK TIMINGS RA4/T0CKI 40 41 42 TABLE 10-6 TIMER0 CLOCK REQUIREMENTS Parameter Sym Characteristic Min Typ† Max Units Conditions No. 40 Tt0H T0CKI High Pulse Width No Prescaler 0.5TCY + 20 * — — ns With Prescaler 50 * — — ns 2.0V  VDD  3.0V 30 * — — ns 3.0V  VDD  6.0V 41 Tt0L T0CKI Low Pulse Width No Prescaler 0.5TCY + 20 * — — ns With Prescaler 50 * — — ns 2.0V  VDD  3.0V 20 * — — ns 3.0V  VDD  6.0V 42 Tt0P T0CKI Period TCY + 40 * — — ns N = prescale value N (2, 4, ..., 256) * These parameters are characterized but not tested. † Data in "Typ" column is at 5.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested.  1996-2013 Microchip Technology Inc. DS30430D-page 11-85

PIC16F8X PIC16F83/84 NOTES: DS30430D-page 11-86  1996-2013 Microchip Technology Inc.

PIC16F8X PIC16CR83/84 11.0 ELECTRICAL CHARACTERISTICS FOR PIC16CR83 AND PIC16CR84 Absolute Maximum Ratings † Ambient temperature under bias.............................................................................................................-55C to +125C Storage temperature.............................................................................................................................. -65C to +150C Voltage on VDD with respect to VSS ........................................................................................................... -0.3 to +7.5V Voltage on MCLR with respect to VSS(2).......................................................................................................-0.3 to +14V Voltage on any pin with respect to VSS (except VDD and MCLR)....................................................-0.6V to (VDD + 0.6V) Total power dissipation(1).....................................................................................................................................800 mW Maximum current out of VSS pin...........................................................................................................................150 mA Maximum current into VDD pin..............................................................................................................................100 mA Input clamp current, IIK (VI < 0 or VI > VDD)20 mA Output clamp current, IOK (VO < 0 or VO > VDD)20 mA Maximum output current sunk by any I/O pin..........................................................................................................25 mA Maximum output current sourced by any I/O pin....................................................................................................20 mA Maximum current sunk byPORTA..........................................................................................................................80 mA Maximum current sourced by PORTA.....................................................................................................................50 mA Maximum current sunk by PORTB........................................................................................................................150 mA Maximum current sourced by PORTB...................................................................................................................100 mA Note 1: Power dissipation is calculated as follows: Pdis = VDD x {IDD -  IOH} +  {(VDD-VOH) x IOH} + (VOl x IOL) Note 2: Voltage spikes below VSS at the MCLR pin, inducing currents greater than 80 mA, may cause latch-up. Thus, a series resistor of 50-100 should be used when applying a “low” level to the MCLR pin rather than pulling this pin directly to VSS. † NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability.  1996-2013 Microchip Technology Inc. DS30430D-page 11-87

PIC16F8X PIC16CR83/84 TABLE 11-1 CROSS REFERENCE OF DEVICE SPECS FOR OSCILLATOR CONFIGURATIONS AND FREQUENCIES OF OPERATION (COMMERCIAL DEVICES) PIC16CR84-04 PIC16CR84-10 PIC16LCR84-04 OSC PIC16CR83-04 PIC16CR83-10 PIC16LCR83-04 RC VDD: 4.0V to 6.0V VDD: 4.5V to 5.5V VDD: 2.0V to 6.0V IDD: 4.5 mA max. at 5.5V IDD: 1.8 mA typ. at 5.5V IDD: 4.5 mA max. at 5.5V IPD: 14 A max. at 4V WDT dis IPD: 1.0 A typ. at 5.5V WDT dis IPD: 5 A max. at 2V WDT dis Freq: 4.0 MHz max. Freq: 4..0 MHz max. Freq: 2.0 MHz max. XT VDD: 4.0V to 6.0V VDD: 4.5V to 5.5V VDD: 2.0V to 6.0V IDD: 4.5 mA max. at 5.5V IDD: 1.8 mA typ. at 5.5V IDD: 4.5 mA max. at 5.5V IPD: 14 A max. at 4V WDT dis IPD: 1.0 A typ. at 5.5V WDT dis IPD: 5 A max. at 2V WDT dis Freq: 4.0 MHz max. Freq: 4.0 MHz max. Freq: 2.0 MHz max. HS VDD: 4.5V to 5.5V VDD: 4.5V to 5.5V IDD: 4.5 mA typ. at 5.5V IDD: 10 mA max. at 5.5V typ. Do not use in HS mode IPD: 1.0 A typ. at 4.5V WDT dis IPD: 1.0 A typ. at 4.5V WDT dis Freq: 4.0 MHz max. Freq: 10 MHz max. LP VDD: 4.0V to 6.0V VDD: 2.0V to 6.0V IDD: 48 A typ. at 32 kHz, 2.0V IDD: 45 A max. at 32 kHz, 2.0V Do not use in LP mode IPD: 0.6 A typ. at 3.0V WDT dis IPD: 5 A max. at 2V WDT dis Freq: 200 kHz max. Freq: 200 kHz max. The shaded sections indicate oscillator selections which are tested for functionality, but not for MIN/MAX specifica- tions. It is recommended that the user select the device type that ensures the specifications required. DS30430D-page 11-88  1996-2013 Microchip Technology Inc.

PIC16F8X PIC16CR83/84 11.1 DC CHARACTERISTICS: PIC16CR84, PIC16CR83 (Commercial, Industrial) Standard Operating Conditions (unless otherwise stated) DC Characteristics Operating temperature 0C  TA  +70C (commercial) Power Supply Pins -40C  TA  +85C (industrial) Parameter Sym Characteristic Min Typ† Max Units Conditions No. D001 VDD Supply Voltage 4.0 — 6.0 V XT, RC and LP osc configuration D001A 4.5 — 5.5 V HS osc configuration D002 VDR RAM Data Retention 1.5* — — V Device in SLEEP mode Voltage(1) D003 VPOR VDD start voltage to — VSS — V See section on Power-on Reset for details ensure internal Power-on Reset signal D004 SVDD VDD rise rate to ensure 0.05* — — V/ms See section on Power-on Reset for details internal Power-on Reset signal IDD Supply Current(2) RC and XT osc configuration(4) D010 — 1.8 4.5 mA FOSC = 4.0 MHz, VDD = 5.5V D010A — 7.3 10 mA FOSC = 4.0 MHz, VDD = 5.5V (During EEPROM programming) HS OSC CONFIGURATION (PIC16CR84-10) D013 — 5 10 mA FOSC = 10 MHz, VDD = 5.5V D020 IPD Power-down Current(3) — 7.0 28 A VDD = 4.0V, WDT enabled, industrial D021 — 1.0 14 A VDD = 4.0V, WDT disabled, commercial D021A — 1.0 16 A VDD = 4.0V, WDT disabled, industrial * These parameters are characterized but not tested. † Data in "Typ" column is at 5.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data. 2: The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin loading and switching rate, oscillator type, internal code execution pattern, and temperature also have an impact on the current consumption. The test conditions for all IDD measurements in active operation mode are: OSC1=external square wave, from rail to rail; all I/O pins tristated, pulled to VDD, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified. 3: The power down current in SLEEP mode does not depend on the oscillator type. Power-down current is measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS. 4: For RC osc configuration, current through Rext is not included. The current through the resistor can be esti- mated by the formula IR = VDD/2Rext (mA) with Rext in kOhm.  1996-2013 Microchip Technology Inc. DS30430D-page 11-89

PIC16F8X PIC16CR83/84 11.2 DC CHARACTERISTICS: PIC16LCR84, PIC16LCR83 (Commercial, Industrial) Standard Operating Conditions (unless otherwise stated) DC Characteristics Operating temperature 0C  TA  +70C (commercial) Power Supply Pins -40C  TA  +85C (industrial) Parameter Sym Characteristic Min Typ† Max Units Conditions No. D001 VDD Supply Voltage 2.0 — 6.0 V XT, RC, and LP osc configuration D002 VDR RAM Data Retention 1.5* — — V Device in SLEEP mode Voltage(1) D003 VPOR VDD start voltage to — VSS — V See section on Power-on Reset for details ensure internal Power-on Reset signal D004 SVDD VDD rise rate to ensure 0.05* — — V/ms See section on Power-on Reset for details internal Power-on Reset signal IDD Supply Current(2) RC and XT osc configuration(4) D010 — 1 4 mA FOSC = 2.0 MHz, VDD = 5.5V D010A — 7.3 10 mA FOSC = 2.0 MHz, VDD = 5.5V (During EEPROM programming) LP osc configuration D014 — 15 45 A FOSC = 32 kHz, VDD = 2.0V, WDT disabled D020 IPD Power-down Current(3) — 3.0 16 A VDD = 2.0V, WDT enabled, industrial D021 — 0.4 5.0 A VDD = 2.0V, WDT disabled, commercial D021A — 0.4 6.0 A VDD = 2.0V, WDT disabled, industrial * These parameters are characterized but not tested. † Data in "Typ" column is at 5.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data. 2: The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin loading and switching rate, oscillator type, internal code execution pattern, and temperature also have an impact on the current consumption. The test conditions for all IDD measurements in active operation mode are: OSC1=external square wave, from rail to rail; all I/O pins tristated, pulled to VDD, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified. 3: The power down current in SLEEP mode does not depend on the oscillator type. Power-down current is measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS. 4: For RC osc configuration, current through Rext is not included. The current through the resistor can be estimated by the formula IR = VDD/2Rext (mA) with Rext in kOhm. DS30430D-page 11-90  1996-2013 Microchip Technology Inc.

PIC16F8X PIC16CR83/84 11.3 DC CHARACTERISTICS: PIC16CR84, PIC16CR83 (Commercial, Industrial) PIC16LCR84, PIC16LCR83 (Commercial, Industrial) Standard Operating Conditions (unless otherwise stated) DC Characteristics Operating temperature 0C  TA  +70C (commercial) All Pins Except -40C  TA  +85C (industrial) Power Supply Pins Operating voltage VDD range as described in DC spec Section11.1 and Section11.2. Parame- ter No. Sym Characteristic Min Typ† Max Units Conditions Input Low Voltage VIL I/O ports D030 with TTL buffer VSS — 0.8 V 4.5 V  Vdd  5.5 V(4) D030A VSS — 0.16VDD V entire range(4) D031 with Schmitt Trigger buffer VSS — 0.2VDD V entire range D032 MCLR, RA4/T0CKI Vss — 0.2VDD V D033 OSC1 (XT, HS and LP modes)(1) Vss — 0.3VDD V D034 OSC1 (RC mode) Vss — 0.1VDD V Input High Voltage VIH I/O ports — D040 with TTL buffer 2.4 — VDD V 4.5 V  VDD 5.5V(4) D040A 0.48VDD — VDD V entire range(4) D041 with Schmitt Trigger buffer 0.45VDD — VDD entire range D042 MCLR, RA4/T0CKI, OSC1 0.85 — VDD V (RC mode) VDD D043 OSC1 (XT, HS and LP modes)(1) 0.7 VDD — VDD V D050 VHYS Hysteresis of TBD — — V Schmitt Trigger inputs D070 IPURB PORTB weak pull-up current 50* 250* 400* A VDD = 5.0V, VPIN = VSS Input Leakage Current(2,3) D060 IIL I/O ports — — 1 A Vss VPIN VDD, Pin at hi-impedance D061 MCLR, RA4/T0CKI — — 5 A Vss VPIN VDD D063 OSC1 — — 5 A Vss VPIN VDD, XT, HS and LP osc configuration Output Low Voltage D080 VOL I/O ports — — 0.6 V IOL = 8.5 mA, VDD = 4.5V D083 OSC2/CLKOUT — — 0.6 V IOL = 1.6 mA, VDD = 4.5V Output High Voltage D090 VOH I/O ports(3) VDD-0.7 — — V IOH = -3.0 mA, VDD = 4.5V D092 OSC2/CLKOUT VDD-0.7 — — V IOH = -1.3 mA, VDD = 4.5V * These parameters are characterized but not tested. † Data in “Typ” column is at 5.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: In RC oscillator configuration, the OSC1 pin is a Schmitt Trigger input. Do not drive the PIC16CR8X with an external clock while the device is in RC mode, or chip damage may result. 2: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified lev- els represent normal operating conditions. Higher leakage current may be measured at different input volt- ages. 3: Negative current is defined as coming out of the pin. 4: The user may choose the better of the two specs.  1996-2013 Microchip Technology Inc. DS30430D-page 11-91

PIC16F8X PIC16CR83/84 11.4 DC CHARACTERISTICS: PIC16CR84, PIC16CR83 (Commercial, Industrial) PIC16LCR84, PIC16LCR83 (Commercial, Industrial) Standard Operating Conditions (unless otherwise stated) DC Characteristics Operating temperature 0C  TA  +70C (commercial) All Pins Except -40C  TA  +85C (industrial) Power Supply Pins Operating voltage VDD range as described in DC spec Section11.1 and Section11.2. Parameter Sym Characteristic Min Typ† Max Units Conditions No. Capacitive Loading Specs on Output Pins D100 COSC2 OSC2 pin — — 15 pF In XT, HS and LP modes when external clock is used to drive OSC1. D101 CIO All I/O pins and OSC2 — — 50 pF (RC mode) Data EEPROM Memory D120 ED Endurance 1M 10M — E/W 25C at 5V D121 VDRW VDD for read/write VMIN — 6.0 V VMIN = Minimum operating voltage D122 TDEW Erase/Write cycle time — 10 20* ms * These parameters are characterized but not tested. † Data in “Typ” column is at 5.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. DS30430D-page 11-92  1996-2013 Microchip Technology Inc.

PIC16F8X PIC16CR83/84 TABLE 11-2 TIMING PARAMETER SYMBOLOGY The timing parameter symbols have been created fol- lowing one of the following formats: 1. TppS2ppS 2. TppS T F Frequency T Time Lowercase symbols (pp) and their meanings: pp 2 to os,osc OSC1 ck CLKOUT ost oscillator start-up timer cy cycle time pwrt power-up timer io I/O port rbt RBx pins inp INT pin t0 T0CKI mc MCLR wdt watchdog timer Uppercase symbols and their meanings: S F Fall P Period H High R Rise I Invalid (Hi-impedance) V Valid L Low Z High Impedance FIGURE 11-1: PARAMETER MEASUREMENT INFORMATION All timings are measure between high and low mea- surement points as indicated in the figures below. 0.7 VDD XTAL (High) 0.8 VDD RC 0.9 VDD (High) 0.3 VDD XTAL 0.1 VDD (Low) (Low) 0.15 VDD RC OSC1 Measurement Points I/O Port Measurement Points FIGURE 11-2: LOAD CONDITIONS Load Condition 1 Load Condition 2 VDD/2 RL Pin CL Pin CL VSS VSS RL = 464 CL = 50 pF for all pins except OSC2. 15 pF for OSC2 output.  1996-2013 Microchip Technology Inc. DS30430D-page 11-93

PIC16F8X PIC16CR83/84 11.5 Timing Diagrams and Specifications FIGURE 11-3: EXTERNAL CLOCK TIMING Q4 Q1 Q2 Q3 Q4 Q1 OSC1 1 3 3 4 4 2 CLKOUT TABLE 11-3 EXTERNAL CLOCK TIMING REQUIREMENTS Parameter No. Sym Characteristic Min Typ† Max Units Conditions (1) FOSC External CLKIN Frequency DC — 2 MHz XT, RC osc PIC16LCR8X-04 DC — 4 MHz XT, RC osc PIC16CR8X-04 DC — 10 MHz HS osc PIC16CR8X-10 DC — 200 kHz LP osc PIC16LCR8X-04 (1) Oscillator Frequency DC — 2 MHz RC osc PIC16LCR8X-04 DC — 4 MHz RC osc PIC16CR8X-04 0.1 — 2 MHz XT osc PIC16LCR8X-04 0.1 — 4 MHz XT osc PIC16CR8X-04 1.0 — 10 MHz HS osc PIC16CR8X-10 DC — 200 kHz LP osc PIC16LCR8X-04 (1) 1 Tosc External CLKIN Period 500 — — ns XT, RC osc PIC16LCR8X-04 250 — — ns XT, RC osc PIC16CR8X-04 100 — — ns HS osc PIC16CR8X-10 5.0 — — s LP osc PIC16LCR8X-04 (1) Oscillator Period 500 — — ns RC osc PIC16LCR8X-04 250 — — ns RC osc PIC16CR8X-04 500 — 10,000 ns XT osc PIC16LCR8X-04 250 — 10,000 ns XT osc PIC16CR8X-04 100 — 1,000 ns HS osc PIC16CR8X-10 5.0 — — s LP osc PIC16LCR8X-04 (1) 2 TCY Instruction Cycle Time 0.4 4/Fosc DC s 3 TosL, Clock in (OSC1) High or Low 60 * — — ns XT osc PIC16LCR8X-04 TosH Time 50 * — — ns XT osc PIC16CR8X-04 2.0 * — — s LP osc PIC16LCR8X-04 35 * — — ns HS osc PIC16CR8X-10 4 TosR, Clock in (OSC1) Rise or Fall Time 25 * — — ns XT osc PIC16CR8X-04 TosF 50 * — — ns LP osc PIC16LCR8X-04 15 * — — ns HS osc PIC16CR8X-10 * These parameters are characterized but not tested. † Data in "Typ" column is at 5.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: Instruction cycle period (TCY) equals four times the input oscillator time base period. All specified values are based on characterization data for that particular oscillator type under standard operating conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation and/or higher than expected current consumption. All devices are tested to operate at "min." values with an external clock applied to the OSC1 pin. When an external clock input is used, the "Max." cycle time limit is "DC" (no clock) for all devices. DS30430D-page 11-94  1996-2013 Microchip Technology Inc.

PIC16F8X PIC16CR83/84 FIGURE 11-4: CLKOUT AND I/O TIMING Q4 Q1 Q2 Q3 OSC1 11 10 22 CLKOUT 23 13 12 19 18 14 16 I/O Pin (input) 17 15 I/O Pin old value new value (output) 20, 21 Note: All tests must be done with specified capacitive loads (Figure11-2) 50 pF on I/O pins and CLKOUT. TABLE 11-4 CLKOUT AND I/O TIMING REQUIREMENTS Parameter No. Sym Characteristic Min Typ† Max Units Conditions 10 TosH2ckL OSC1 to CLKOUT PIC16CR8X — 15 30 * ns Note 1 10A PIC16LCR8X — 15 120 * ns Note 1 11 TosH2ckH OSC1 to CLKOUT PIC16CR8X — 15 30 * ns Note 1 11A PIC16LCR8X — 15 120 * ns Note 1 12 TckR CLKOUT rise time PIC16CR8X — 15 30 * ns Note 1 12A PIC16LCR8X — 15 100 * ns Note 1 13 TckF CLKOUT fall time PIC16CR8X — 15 30 * ns Note 1 13A PIC16LCR8X — 15 100 * ns Note 1 14 TckL2ioV CLKOUT  to Port out valid — — 0.5TCY +20 * ns Note 1 15 TioV2ckH Port in valid before PIC16CR8X 0.30TCY + 30 * — — ns Note 1 CLKOUT  PIC16LCR8X 0.30TCY + 80 * — — ns Note 1 16 TckH2ioI Port in hold after CLKOUT  0 * — — ns Note 1 17 TosH2ioV OSC1 (Q1 cycle) to PIC16CR8X — — 125 * ns Port out valid PIC16LCR8X — — 250 * ns 18 TosH2ioI OSC1 (Q2 cycle) to PIC16CR8X 10 * — — ns Port input invalid (I/O PIC16LCR8X 10 * — — ns in hold time) 19 TioV2osH Port input valid to PIC16CR8X -75 * — — ns OSC1(I/O in setup PIC16LCR8X -175 * — — ns time) 20 TioR Port output rise time PIC16CR8X — 10 35 * ns 20A PIC16LCR8X — 10 70 * ns 21 TioF Port output fall time PIC16CR8X — 10 35 * ns 21A PIC16LCR8X — 10 70 * ns 22 Tinp INT pin high PIC16CR8X 20 * — — ns 22A or low time PIC16LCR8X 55 * — — ns 23 Trbp RB7:RB4 change INT PIC16CR8X TOSC § — — ns 23A high or low time PIC16LCR8X TOSC § — — ns * These parameters are characterized but not tested. † Data in "Typ" column is at 5.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. § By design Note 1: Measurements are taken in RC Mode where CLKOUT output is 4 x TOSC.  1996-2013 Microchip Technology Inc. DS30430D-page 11-95

PIC16F8X PIC16CR83/84 FIGURE 11-5: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER AND POWER-UP TIMER TIMING VDD MCLR 30 Internal POR 33 PWRT Time-out 32 OSC Time-out Internal RESET Watchdog Timer RESET 31 34 34 I/O Pins TABLE 11-5 RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER AND POWER-UP TIMER REQUIREMENTS Parameter No. Sym Characteristic Min Typ† Max Units Conditions 30 TmcL MCLR Pulse Width (low) 1000 * — — ns 2.0V  VDD  6.0V 31 Twdt Watchdog Timer Time-out Period 7 * 18 33 * ms VDD = 5.0V (No Prescaler) 32 Tost Oscillation Start-up Timer Period 1024TOSC ms TOSC = OSC1 period 33 Tpwrt Power-up Timer Period 28 * 72 132 * ms VDD = 5.0V 34 TIOZ I/O Hi-impedance from MCLR Low — — 100 * ns or reset * These parameters are characterized but not tested. † Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. DS30430D-page 11-96  1996-2013 Microchip Technology Inc.

PIC16F8X PIC16CR83/84 FIGURE 11-6: TIMER0 CLOCK TIMINGS RA4/T0CKI 40 41 42 TABLE 11-6 TIMER0 CLOCK REQUIREMENTS Parameter Sym Characteristic Min Typ† Max Units Conditions No. 40 Tt0H T0CKI High Pulse Width No Prescaler 0.5TCY + 20 * — — ns With Prescaler 50 * — — ns 2.0V  VDD  3.0V 30 * — — ns 3.0V  VDD  6.0V 41 Tt0L T0CKI Low Pulse Width No Prescaler 0.5TCY + 20 * — — ns With Prescaler 50 * — — ns 2.0V  VDD  3.0V 20 * — — ns 3.0V  VDD  6.0V 42 Tt0P T0CKI Period TCY + 40 * — — ns N = prescale value N (2, 4, ..., 256) * These parameters are characterized but not tested. † Data in "Typ" column is at 5.0V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested.  1996-2013 Microchip Technology Inc. DS30430D-page 11-97

PIC16F8X PIC16CR83/84 NOTES: DS30430D-page 11-98  1996-2013 Microchip Technology Inc.

PIC16F8X 12.0 DC & AC CHARACTERISTICS GRAPHS/TABLES The graphs and tables provided in this section are for design guidance and are not tested or guaranteed. In some graphs or tables, the data presented are outside specified operating range (i.e., outside specified VDD range). This is for information only and devices are guaranteed to operate properly only within the specified range. The data presented in this section is a statistical summary of data collected on units from different lots over a period of time and matrix samples. 'Typical' represents the mean of the distribution at 25C, while 'max' or 'min' represents (mean+3) and (mean-3) respectively, where  is standard deviation. FIGURE 12-1: TYPICAL RC OSCILLATOR FREQUENCY vs. TEMPERATURE FOSC Frequency normalized to +25C FOSC (25C) 1.20 Rext  10 k 1.16 Cext = 100 pF 1.12 1.08 1.04 1.00 0.96 VDD = 5.5 V 0.92 VDD = 3.5 V 0.88 0.84 -40 -20 0 2025 40 60 70 80 85 100 T(C) TABLE 12-1 RC OSCILLATOR FREQUENCIES* Average Cext Rext Fosc @ 5V, 25C Part to Part Variation 20 pF 5 k 4.61 MHz  25% 10 k 2.66 MHz  24% 100 k 311 kHz  39% 100 pF 5 k 1.34 MHz  21% 10 k 756 kHz  18% 100 k 82.8 kHz  28% 300 pF 5 k 428 kHz  13% 10 k 243 kHz  13% 100 k 26.2 kHz  23% * Measured on DIP packages. The percentage variation indicated here is part-to-part variation due to normal process distribution. The variation indicated is 3 standard deviation from average value for full VDD range.  1996-2013 Microchip Technology Inc. DS30430D-page 11-99

PIC16F8X FIGURE 12-2: TYPICAL RC OSCILLATOR FREQUENCY vs. VDD, CEXT = 20 PF Measured on DIP Packages, T = 25°C 5.5 5.0 R = 5k 4.5 4.0 3.5 z) H R = 10k M c ( 3.0 s o F 2.5 2.0 1.5 1.0 0.5 R = 100k 0.0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 VDD (Volts) DS30430D-page 11-100  1996-2013 Microchip Technology Inc.

PIC16F8X FIGURE 12-3: TYPICAL RC OSCILLATOR FREQUENCY vs. VDD, CEXT = 100 PF Measured on DIP Packages, T = 25°C 1.8 R = 5k 1.6 1.4 1.2 z) H M 1.0 c ( R = 10k s o F 0.8 0.6 0.4 0.2 R = 100k 0.0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 VDD (Volts) FIGURE 12-4: TYPICAL RC OSCILLATOR FREQUENCY vs. VDD, CEXT = 300 PF Measured on DIP Packages, T = 25°C 0.6 R = 5k 0.5 z) H0.4 M ( C S FO0.3 R = 10k 0.2 0.1 R = 100k 0.0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 VDD (Volts)  1996-2013 Microchip Technology Inc. DS30430D-page 11-101

PIC16F8X FIGURE 12-5: TYPICAL IPD vs. VDD, FIGURE 12-6: TYPICAL IPD vs. VDD, WATCHDOG DISABLED WATCHDOG ENABLED 6.0 10 9 5.0 8 T = 25C T = 25C 7 4.0 6 A) A) (D 5  P (D 3.0 I 4 P I 3 2.0 2 1 1.0 0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 VDD (Volts) 0.0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 VDD (Volts) FIGURE 12-7: VTH (INPUT THRESHOLD VOLTAGE) OF I/O PINS vs. VDD 1.40 1.30 s) 1.20 (Volt 1.10 Typ (+25C) H T V 1.00 0.90 0.80 0.70 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 VDD (Volts) Note: These input pins have TTL input buffers. DS30430D-page 11-102  1996-2013 Microchip Technology Inc.

PIC16F8X FIGURE 12-8: VTH (INPUT THRESHOLD VOLTAGE) OF OSC1 INPUT (IN XT, HS, AND LP MODES) vs. VDD 3.0 2.8 2.6 2.4 2.2 s) (VoltH 21..08 Typ (+25C) T V 1.6 1.4 1.2 1.0 0.8 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 VDD (Volts) Note: This input pin is CMOS input. FIGURE 12-9: VIH, VIL OF MCLR, T0CKI AND OSC1 (IN RC MODE) vs. VDD 5.0 4.5 4.0 3.5 olts) 3.0 VIH typ +25C V 2.5 ( L VI , H 2.0 VI 1.5 VIL typ +25C 1.0 0.5 0.0 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 VDD (Volts) Note: These input pins have Schmitt Trigger input buffers.  1996-2013 Microchip Technology Inc. DS30430D-page 11-103

PIC16F8X FIGURE 12-10:TYPICAL IDD vs. FREQUENCY (RC MODE @20PF, 25C) TYPICAL IDD vs FREQ (RC MODE @20pF) 10000 1000 6.0V 5.5V 5.0V 4.5V 4.0V 3.5V 100 3.0V 2.5V 2.0V 10 100000 1000000 10000000 FREQ (Hz) DS30430D-page 11-104  1996-2013 Microchip Technology Inc.

PIC16F8X FIGURE 12-11:TYPICAL IDD vs. FREQUENCY (RC MODE @100PF, 25C) TYPICAL IDD vs FREQ (RC MODE @100 pF) 10000 1000 6.0V 5.5V 100 5.0V 4.5V 4.0V 3.5V 3.0V 2.5V 2.0V 10 10000 100000 1000000 10000000 FREQ (Hz)  1996-2013 Microchip Technology Inc. DS30430D-page 11-105

PIC16F8X FIGURE 12-12:TYPICAL IDD vs. FREQUENCY (RC MODE @300PF, 25C) TYPICAL IDD vs FREQ (RC MODE @300pF) 1000 6.0V 5.5V 100 5.0V 4.5V 4.0V 3.5V 3.0V 2.5V 2.0V 10 10000 100000 1000000 FREQ (Hz) DS30430D-page 11-106  1996-2013 Microchip Technology Inc.

PIC16F8X FIGURE 12-13:WDT TIMER TIME-OUT FIGURE 12-14:TRANSCONDUCTANCE (gm) PERIOD vs. VDD OF HS OSCILLATOR vs. VDD 50 9000 45 8000 40 7000 35 6000 s) m od ( 30 V) 5000 eri A/ Typ +25C p  T 25 Typ +25C m ( 4000 D W g 20 3000 15 2000 10 100 5 0 2.0 3.0 4.0 5.0 6.0 2.0 3.0 4.0 5.0 6.0 VDD (Volts) VDD (Volts)  1996-2013 Microchip Technology Inc. DS30430D-page 11-107

PIC16F8X FIGURE 12-15:TRANSCONDUCTANCE (gm) FIGURE 12-16:TRANSCONDUCTANCE (gm) OF LP OSCILLATOR vs. VDD OF XT OSCILLATOR vs. VDD 45 2500 40 2000 35 30 1500 25 Typ +25C V) V) A/ A/   m ( 20 m ( 1000 g Typ +25C g 15 500 10 5 0 2.0 3.0 4.0 5.0 6.0 0 2.0 3.0 4.0 5.0 6.0 VDD (Volts) VDD (Volts) DS30430D-page 11-108  1996-2013 Microchip Technology Inc.

PIC16F8X FIGURE 12-17:IOH vs. VOH, VDD = 3 V FIGURE 12-19:IOL vs. VOL, VDD = 3 V 45 0 40 –5 35 30 –10 ) Typ +25C A 25 Typ +25C m ) A (H m IO (OL 20 –15 I 15 –20 10 5 –25 0.0 0.5 1.0 1.5 2.0 2.5 3.0 0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 VOH (Volts) VOL (Volts) FIGURE 12-18:IOH vs. VOH, VDD = 5 V FIGURE 12-20:IOL vs. VOL, VDD = 5 V 90 0 80 –5 70 –10 60 –15 Typ +25C A) 50 m –20 A) I (OH Typ +25C (mOL 40 –25 I 30 –30 20 –35 10 –40 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 0 VOH (Volts) 0.0 0.5 1.0 1.5 2.0 2.5 3.0 VOL (Volts)  1996-2013 Microchip Technology Inc. DS30430D-page 11-109

PIC16F8X FIGURE 12-21:TYPICAL DATA MEMORY ERASE/WRITE CYCLE TIME VS. VDD 10 9 8 7 s) m e ( m 6 Ti e cl y C 5 W E/ p. 4 y T M E M D 3 2 1 0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 6.5 VDD (Volts) Shaded area is beyond recommended range. TABLE 12-2 INPUT CAPACITANCE* Typical Capacitance (pF) Pin Name 18L PDIP 18L SOIC PORTA 5.0 4.3 PORTB 5.0 4.3 MCLR 17.0 17.0 OSC1/CLKIN 4.0 3.5 OSC2/CLKOUT 4.3 3.5 T0CKI 3.2 2.8 * All capacitance values are typical at 25C. A part to part variation of 25% (three standard deviations) should be taken into account. DS30430D-page 11-110  1996-2013 Microchip Technology Inc.

PIC16F8X 13.0 PACKAGING INFORMATION 13.1 Package Marking Information 18L PDIP Example XXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXX PIC16F84-04I/P AABBCDE 9632SAW 18L SOIC Example XXXXXXXXXXXX XXXXXXXXXXXX PIC16F84-04 XXXXXXXXXXXX /SO AABBCDE 9648SAN Legend: XX...X Customer-specific information Y Year code (last digit of calendar year) YY Year code (last 2 digits of calendar year) WW Week code (week of January 1 is week ‘01’) NNN Alphanumeric traceability code e3 Pb-free JEDEC designator for Matte Tin (Sn) * This package is Pb-free. The Pb-free JEDEC designator ( e 3 ) can be found on the outer packaging for this package. Note: In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information.  1996-2013 Microchip Technology Inc. DS30430D-page 111

PIC16F8X Package Type: K04-007 18-Lead Plastic Dual In-line (P) – 300 mil Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging E D 2 n 1  E1 A1 A R c L A2 B1  B p eB Units INCHES* MILLIMETERS Dimension Limits MIN NOM MAX MIN NOM MAX PCB Row Spacing 0.300 7.62 Number of Pins n 18 18 Pitch p 0.100 2.54 Lower Lead Width B 0.013 0.018 0.023 0.33 0.46 0.58 Upper Lead Width B1† 0.055 0.060 0.065 1.40 1.52 1.65 Shoulder Radius R 0.000 0.005 0.010 0.00 0.13 0.25 Lead Thickness c 0.005 0.010 0.015 0.13 0.25 0.38 Top to Seating Plane A 0.110 0.155 0.155 2.79 3.94 3.94 Top of Lead to Seating Plane A1 0.075 0.095 0.115 1.91 2.41 2.92 Base to Seating Plane A2 0.000 0.020 0.020 0.00 0.51 0.51 Tip to Seating Plane L 0.125 0.130 0.135 3.18 3.30 3.43 Package Length D‡ 0.890 0.895 0.900 22.61 22.73 22.86 Molded Package Width E‡ 0.245 0.255 0.265 6.22 6.48 6.73 Radius to Radius Width E1 0.230 0.250 0.270 5.84 6.35 6.86 Overall Row Spacing eB 0.310 0.349 0.387 7.87 8.85 9.83 Mold Draft Angle Top  5 10 15 5 10 15 Mold Draft Angle Bottom  5 10 15 5 10 15 * Controlling Parameter. † Dimension “B1” does not include dam-bar protrusions. Dam-bar protrusions shall not exceed 0.003” (0.076 mm) per side or 0.006” (0.152 mm) more than dimension “B1.” ‡ Dimensions “D” and “E” do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.010” (0.254 mm) per side or 0.020” (0.508 mm) more than dimensions “D” or “E.” DS30430D-page 112  1996-2013 Microchip Technology Inc.

PIC16F8X Package Type: K04-051 18-Lead Plastic Small Outline (SO) – Wide, 300 mil Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging E1 p E D 2 B n 1 X  45° L R2 c A A1 R1   L1 A2 Units INCHES* MILLIMETERS Dimension Limits MIN NOM MAX MIN NOM MAX Pitch p 0.050 1.27 Number of Pins n 18 18 Overall Pack. Height A 0.093 0.099 0.104 2.36 2.50 2.64 Shoulder Height A1 0.048 0.058 0.068 1.22 1.47 1.73 Standoff A2 0.004 0.008 0.011 0.10 0.19 0.28 Molded Package Length D‡ 0.450 0.456 0.462 11.43 11.58 11.73 Molded Package Width E‡ 0.292 0.296 0.299 7.42 7.51 7.59 Outside Dimension E1 0.394 0.407 0.419 10.01 10.33 10.64 Chamfer Distance X 0.010 0.020 0.029 0.25 0.50 0.74 Shoulder Radius R1 0.005 0.005 0.010 0.13 0.13 0.25 Gull Wing Radius R2 0.005 0.005 0.010 0.13 0.13 0.25 Foot Length L 0.011 0.016 0.021 0.28 0.41 0.53 Foot Angle  0 4 8 0 4 8 Radius Centerline L1 0.010 0.015 0.020 0.25 0.38 0.51 Lead Thickness c 0.009 0.011 0.012 0.23 0.27 0.30 Lower Lead Width B† 0.014 0.017 0.019 0.36 0.42 0.48 Mold Draft Angle Top  0 12 15 0 12 15 Mold Draft Angle Bottom  0 12 15 0 12 15 * Controlling Parameter. † Dimension “B” does not include dam-bar protrusions. Dam-bar protrusions shall not exceed 0.003” (0.076 mm) per side or 0.006” (0.152 mm) more than dimension “B.” ‡ Dimensions “D” and “E” do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.010” (0.254 mm) per side or 0.020” (0.508 mm) more than dimensions “D” or “E.”  1996-2013 Microchip Technology Inc. DS30430D-page 113

PIC16F8X NOTES: DS30430D-page 114  1996-2013 Microchip Technology Inc.

PIC16F8X APPENDIX A: FEATURE APPENDIX B: CODE COMPATIBILITY IMPROVEMENTS - - FROM PIC16C5X TO FROM PIC16C5X TO PIC16F8X PIC16F8X To convert code written for PIC16C5X to PIC16F8X, the user should take the following steps: The following is the list of feature improvements over the PIC16C5X microcontroller family: 1. Remove any program memory page select 1. Instruction word length is increased to 14 bits. operations (PA2, PA1, PA0 bits) for CALL, GOTO. This allows larger page sizes both in program 2. Revisit any computed jump operations (write to memory (2K now as opposed to 512 before) and PC or add to PC, etc.) to make sure page bits the register file (128 bytes now versus 32 bytes are set properly under the new scheme. before). 3. Eliminate any data memory page switching. 2. A PC latch register (PCLATH) is added to handle Redefine data variables for reallocation. program memory paging. PA2, PA1 and PA0 bits 4. Verify all writes to STATUS, OPTION, and FSR are removed from the status register and placed registers since these have changed. in the option register. 5. Change reset vector to 0000h. 3. Data memory paging is redefined slightly. The STATUS register is modified. 4. Four new instructions have been added: RETURN, RETFIE, ADDLW, and SUBLW. Two instructions, TRIS and OPTION, are being phased out although they are kept for compatibility with PIC16C5X. 5. OPTION and TRIS registers are made addressable. 6. Interrupt capability is added. Interrupt vector is at 0004h. 7. Stack size is increased to 8 deep. 8. Reset vector is changed to 0000h. 9. Reset of all registers is revisited. Five different reset (and wake-up) types are recognized. Registers are reset differently. 10. Wake up from SLEEP through interrupt is added. 11. Two separate timers, the Oscillator Start-up Timer (OST) and Power-up Timer (PWRT), are included for more reliable power-up. These timers are invoked selectively to avoid unnecessary delays on power-up and wake-up. 12. PORTB has weak pull-ups and interrupt on change features. 13. T0CKI pin is also a port pin (RA4/T0CKI). 14. FSR is a full 8-bit register. 15. "In system programming" is made possible. The user can program PIC16CXX devices using only five pins: VDD, VSS, VPP, RB6 (clock) and RB7 (data in/out).  1996-2013 Microchip Technology Inc. DS30430D-page 115

PIC16F8X APPENDIX C: WHAT’S NEW IN THIS APPENDIX D: WHAT’S CHANGED IN DATA SHEET THIS DATA SHEET Here’s what’s new in this data sheet: Here’s what’s changed in this data sheet: 1. DC & AC Characteristics Graphs/Tables section 1. Errata information has been included. for PIC16F8X devices has been added. 2. Option register name has been changed from 2. An appendix on conversion considerations has OPTION to OPTION_REG. This is consistant been added. This explains differences for cus- with other data sheets and header files, and tomers wanting to go from PIC16C84 to resolves the conflict between the OPTION com- PIC16F84 or similar device. mand and OPTION register. 3. Errors have been fixed. 4. The appendix containing PIC16/17 microcon- trollers has been removed. Revision D (January 2013) Added a note to each package drawing. DS30430D-page 116  1996-2013 Microchip Technology Inc.

PIC16F8X APPENDIX E: CONVERSION CONSIDERATIONS - PIC16C84 TO PIC16F83/F84 AND PIC16CR83/CR84 Considerations for converting from the PIC16C84 to and data RAM memory sizes) and the PIC16CR84 and the PIC16F84 are listed in the table below. These con- PIC16CR83 (ROM versions of Flash devices). Devel- siderations apply to converting from the PIC16C84 to opment Systems support is available for all of the the PIC16F83 (same as PIC16F84 except for program PIC16X8X devices. Difference PIC16C84 PIC16F84 The polarity of the PWRTE bit has PWRTE PWRTE been reversed. Ensure that the pro- grammer has this bit correctly set before programming. The PIC16F84 (and PIC16CR84) RAM = 36 bytes RAM = 68 bytes have larger RAM sizes. Ensure that this does not cause an issue with your program. The MCLR pin now has an on-chip MCLR pulse width (low) MCLR pulse width (low) filter. The input signal on the MCLR = 350ns; 2.0V  VDD  3.0V = 1000ns; 2.0V  VDD  6.0V pin will require a longer low pulse to = 150ns; 3.0V  VDD  6.0V generate an interrupt. Some electrical specifications have IPD (typ @ 2V) = 26A IPD (typ @ 2V) < 1A been improved (see IPD example). Compare the electrical specifica- IPD (max @ 4V, WDT disabled) IPD (max @ 4V, WDT disabled) tions of the two devices to ensure =100A (PIC16C84) =14A (PIC16F84) that this will not cause a compatibil- =100A (PIC16LC84) =7A (PIC16LF84) ity issue. PORTA and crystal oscillator values For crystal oscillator configurations N/A less than 500kHz operating below 500kHz, the device may generate a spurious internal Q-clock when PORTA<0> switches state. RB0/INT pin TTL TTL/ST* (* This buffer is a Schmitt Trigger input when configured as the exter- nal interrupt.) EEADR<7:6> and IDD It is recommended that the N/A EEADR<7:6> bits be cleared. When either of these bits is set, the maximum IDD for the device is higher than when both are cleared. Code Protect 1 CP bit 9 CP bits Recommended value of REXT for REXT = 3k - 100k REXT = 5k - 100k RC oscillator circuits GIE bit unintentional enable If an interrupt occurs while the N/A Global Interrupt Enable (GIE) bit is being cleared, the GIE bit may unin- tentionally be re-enabled by the user’s Interrupt Service Routine (the RETFIE instruction).  1996-2013 Microchip Technology Inc. DS30430D-page 117

PIC16F8X NOTES: DS30430D-page 118  1996-2013 Microchip Technology Inc.

PIC16F8X INDEX CALL ..........................................................................57 CLRF .........................................................................58 Numerics CLRW ........................................................................58 8.1 Configuration Bits .........................................................37 CLRWDT ...................................................................58 COMF ........................................................................59 A DECF .........................................................................59 Absolute Maximum Ratings .........................................73, 85 DECFSZ ....................................................................59 ALU ......................................................................................7 GOTO ........................................................................60 Architectural Overview .........................................................7 INCF ..........................................................................60 Assembler INCFSZ ......................................................................61 MPASM Assembler ....................................................70 IORLW .......................................................................61 IORWF .......................................................................62 B MOVF ........................................................................62 Block Diagram MOVLW .....................................................................62 Interrupt Logic ............................................................47 MOVWF .....................................................................62 On-Chip Reset Circuit ................................................41 NOP ...........................................................................63 RA3:RA0 and RA5 Port Pins .....................................21 OPTION .....................................................................63 RA4 Pin ......................................................................21 RETFIE ......................................................................63 RB7:RB4 Port Pins ....................................................23 RETLW ......................................................................64 TMR0/WDT Prescaler ................................................30 RETURN ....................................................................64 Watchdog Timer .........................................................50 RLF ............................................................................65 Brown-out Protection Circuit ..............................................46 RRF ...........................................................................65 SLEEP .......................................................................66 C SUBLW ......................................................................66 Carry ....................................................................................7 SUBWF ......................................................................67 CLKIN ..................................................................................9 SWAPF ......................................................................67 CLKOUT ..............................................................................9 TRIS ..........................................................................67 Code Protection ...........................................................37, 52 XORLW .....................................................................68 Compatibility, upward ...........................................................3 XORWF .....................................................................68 Computed GOTO ...............................................................18 Section .......................................................................53 Configuration Bits ...............................................................37 Summary Table .........................................................54 D INT Interrupt ......................................................................48 INTCON ...........................................................17, 42, 47, 48 DC Characteristics ...................75, 76, 77, 78, 87, 88, 89, 90 INTEDG .............................................................................48 Development Support ........................................................69 Interrupts Development Tools ............................................................69 Flag ............................................................................47 Digit Carry ............................................................................7 Interrupt on Change Feature .....................................23 E Interrupts .............................................................37, 47 Electrical Characteristics ..............................................73, 85 K External Power-on Reset Circuit ........................................43 KeeLoq Evaluation and Programming Tools ..................71 F L Family of Devices Loading of PC ....................................................................18 PIC16C8X ....................................................................3 FSR ..............................................................................19, 42 M Fuzzy Logic Dev. System (fuzzyTECH-MP) ...................71 MCLR ......................................................................9, 41, 42 G Memory Organization Data Memory .............................................................12 GIE .....................................................................................47 Memory Organization ................................................11 I Program Memory .......................................................11 MP-DriveWay™ - Application Code Generator .................71 I/O Ports .............................................................................21 MPLAB C ...........................................................................71 I/O Programming Considerations .......................................25 MPLAB Integrated Development Environment Software ...70 ICEPIC Low-Cost PIC16CXXX In-Circuit Emulator ...........69 In-Circuit Serial Programming ......................................37, 52 O INDF ...................................................................................42 OPCODE ...........................................................................53 Instruction Format ..............................................................53 OPTION .................................................................16, 42, 48 Instruction Set OSC selection ....................................................................37 ADDLW ......................................................................55 OSC1 ...................................................................................9 ADDWF ......................................................................55 OSC2 ...................................................................................9 ANDLW ......................................................................55 Oscillator ANDWF ......................................................................55 HS ........................................................................39, 46 BCF ............................................................................56 LP ........................................................................39, 46 BSF ............................................................................56 RC .......................................................................39, 40 BTFSC .......................................................................56 XT ..............................................................................39 BTFSS .......................................................................57 Oscillator Configurations ....................................................39  1996-2013 Microchip Technology Inc. DS30430D-page 119

PIC16F8X P Programming Considerations ....................................50 Time-out ....................................................................42 Paging, Program Memory ..................................................18 PCL ..............................................................................18, 42 X PCLATH .......................................................................18, 42 XT ......................................................................................46 PD ..........................................................................15, 41, 46 PICDEM-1 Low-Cost PIC MCU Demo Board ....................70 Z PICDEM-2 Low-Cost PIC16CXX Demo Board ..................70 Zero bit .................................................................................7 PICDEM-3 Low-Cost PIC16CXXX Demo Board ................70 PICMASTER In-Circuit Emulator .....................................69 PICSTART Plus Entry Level Development System ........69 Pinout Descriptions ..............................................................9 POR ...................................................................................43 Oscillator Start-up Timer (OST) ...........................37, 43 Power-on Reset (POR) ..................................37, 42, 43 Power-up Timer (PWRT) .....................................37, 43 Time-out Sequence ....................................................46 Time-out Sequence on Power-up ..............................44 TO ..................................................................15, 41, 46 Port RB Interrupt ................................................................48 PORTA .....................................................................9, 21, 42 PORTB .....................................................................9, 23, 42 Power-down Mode (SLEEP) ..............................................51 Prescaler ............................................................................29 PRO MATE II Universal Programmer ..............................69 Product Identification System ...........................................121 R RBIF bit ........................................................................23, 48 RC Oscillator ......................................................................46 Read-Modify-Write .............................................................25 Register File .......................................................................12 Reset ............................................................................37, 41 Reset on Brown-Out ...........................................................46 S Saving W Register and STATUS in RAM ..........................49 SEEVAL Evaluation and Programming System ..............71 SLEEP ....................................................................37, 41, 51 Software Simulator (MPLAB-SIM) ......................................71 Special Features of the CPU ..............................................37 Special Function Registers ................................................12 Stack ..................................................................................18 Overflows ...................................................................18 Underflows .................................................................18 STATUS ...................................................................7, 15, 42 T time-out ..............................................................................42 Timer0 Switching Prescaler Assignment ................................31 T0IF ............................................................................48 Timer0 Module ...........................................................27 TMR0 Interrupt ...........................................................48 TMR0 with External Clock ..........................................29 Timing Diagrams Time-out Sequence ....................................................44 Timing Diagrams and Specifications ............................80, 92 TRISA .................................................................................21 TRISB ...........................................................................23, 42 W W ........................................................................................42 Wake-up from SLEEP ..................................................42, 51 Watchdog Timer (WDT) ...................................37, 41, 42, 50 WDT ...................................................................................42 Period .........................................................................50 DS30430D-page 120  1996-2013 Microchip Technology Inc.

PIC16F8X ON-LINE SUPPORT Microchip provides on-line support on the Microchip World Wide Web (WWW) site. The web site is used by Microchip as a means to make files and information easily available to customers. To view the site, the user must have access to the Internet and a web browser, such as Netscape or Microsoft Explorer. Files are also available for FTP download from our FTP site. Connecting to the Microchip Internet Web Site The Microchip web site is available by using your favorite Internet browser to attach to: www.microchip.com The file transfer site is available by using an FTP ser- vice to connect to: ftp://ftp.futureone.com/pub/microchip The web site and file transfer site provide a variety of services. Users may download files for the latest Development Tools, Data Sheets, Application Notes, User's Guides, Articles and Sample Programs. A vari- ety of Microchip specific business information is also available, including listings of Microchip sales offices, distributors and factory representatives. Other data available for consideration is: (cid:129) Latest Microchip Press Releases (cid:129) Technical Support Section with Frequently Asked Questions (cid:129) Design Tips (cid:129) Device Errata (cid:129) Job Postings (cid:129) Microchip Consultant Program Member Listing (cid:129) Links to other useful web sites related to Microchip Products (cid:129) Conferences for products, Development Sys- tems, technical information and more (cid:129) Listing of seminars and events  1998 Microchip Technology Inc. DS30430D-page11-121

PIC16F8X READER RESPONSE It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip prod- uct. If you wish to provide your comments on organization, clarity, subject matter, and ways in which our documentation can better serve you, please FAX your comments to the Technical Publications Manager at (602) 786-7578. Please list the following information, and use this outline to provide us with your comments about this Data Sheet. To: Technical Publications Manager Total Pages Sent RE: Reader Response From: Name Company Address City / State / ZIP / Country Telephone: (_______) _________ - _________ FAX: (______) _________ - _________ Application (optional): Would you like a reply? Y N Device: PIC16F8X Literature Number: DS30430D Questions: 1. What are the best features of this document? 2. How does this document meet your hardware and software development needs? 3. Do you find the organization of this data sheet easy to follow? If not, why? 4. What additions to the data sheet do you think would enhance the structure and subject? 5. What deletions from the data sheet could be made without affecting the overall usefulness? 6. Is there any incorrect or misleading information (what and where)? 7. How would you improve this document? 8. How would you improve our software, systems, and silicon products? DS30430D-page11-122  1998 Microchip Technology Inc.

PIC16F8X PIC16F8X PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. PART NO. -XX X /XX XXX Examples: Device Frequency Temperature Package Pattern a) PIC16F84 -04/P 301 = Commercial Range Range temp., PDIP package, 4 MHz, normal VDD limits, QTP pattern #301. Device PIC16F8X(2), PIC16F8XT(3) b) PIC16LF84 - 04I/SO = Industrial temp., PIC16LF8X(2), PIC16LF8XT(3) PIC16F8XA(2), PIC16F8XAT(3) SOIC package, 200 kHz, Extended VDD limits. PIC16LF8XA(2), PIC16LF8XAT(3) PIC16CR8X(2), PIC16CR8XT(3) c) PIC16CR84 - 10I/P = ROM program PIC16LCR8X(2), PIC16LCR8XT(3) memory, Industrial temp., PDIP package, 10MHz, normal VDD limits. Frequency 04 = 4 MHz Range 10 = 10 MHz 20 = 20 MHz Note 1: b = blank Temperature b(1) = 0C to +70C (Commercial) 2: F = Standard VDD range LF = Extended VDD range Range I = -40C to +85C (Industrial) CR = ROM Version, Standard VDD Package P = PDIP range SO = SOIC (Gull Wing, 300 mil body) LCR= ROM Version, Extended VDD SS = SSOP range 3: T = in tape and reel - SOIC, SSOP Pattern 3-digit Pattern Code for QTP, ROM (blank otherwise) packages only. SALES AND SUPPORT Products supported by a preliminary Data Sheet may possibly have an errata sheet describing minor operational differences and recommended workarounds. To determine if an errata sheet exists for a particular device, please contact one of the following: 1. Your local Microchip sales office. 2. The Microchip’s Bulletin Board, via your local CompuServe number (CompuServe membership NOT required).  1996-2013 Microchip Technology Inc. DS30430D-page 123

PIC16F8X NOTES: DS30430D-page 124  1996-2013 Microchip Technology Inc.

PIC16F8X NOTES:  1996-2013 Microchip Technology Inc. DS30430D-page 125

PIC16F8X DS30430D-page 126  1996-2013 Microchip Technology Inc.

Note the following details of the code protection feature on Microchip devices: • Microchip products meet the specification contained in their particular Microchip Data Sheet. • Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. • There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. • Microchip is willing to work with the customer who is concerned about the integrity of their code. • Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as “unbreakable.” Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device Trademarks applications and the like is provided only for your convenience The Microchip name and logo, the Microchip logo, dsPIC, and may be superseded by updates. It is your responsibility to FlashFlex, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, ensure that your application meets with your specifications. PICSTART, PIC32 logo, rfPIC, SST, SST Logo, SuperFlash MICROCHIP MAKES NO REPRESENTATIONS OR and UNI/O are registered trademarks of Microchip Technology WARRANTIES OF ANY KIND WHETHER EXPRESS OR Incorporated in the U.S.A. and other countries. IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor, INCLUDING BUT NOT LIMITED TO ITS CONDITION, MTP, SEEVAL and The Embedded Control Solutions QUALITY, PERFORMANCE, MERCHANTABILITY OR Company are registered trademarks of Microchip Technology FITNESS FOR PURPOSE. Microchip disclaims all liability Incorporated in the U.S.A. arising from this information and its use. Use of Microchip Silicon Storage Technology is a registered trademark of devices in life support and/or safety applications is entirely at Microchip Technology Inc. in other countries. the buyer’s risk, and the buyer agrees to defend, indemnify and Analog-for-the-Digital Age, Application Maestro, BodyCom, hold harmless Microchip from any and all damages, claims, chipKIT, chipKIT logo, CodeGuard, dsPICDEM, suits, or expenses resulting from such use. No licenses are dsPICDEM.net, dsPICworks, dsSPEAK, ECAN, conveyed, implicitly or otherwise, under any Microchip ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial intellectual property rights. Programming, ICSP, Mindi, MiWi, MPASM, MPF, MPLAB Certified logo, MPLIB, MPLINK, mTouch, Omniscient Code Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit, PICtail, REAL ICE, rfLAB, Select Mode, SQI, Serial Quad I/O, Total Endurance, TSHARC, UniWinDriver, WiperLock, ZENA and Z-Scale are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. GestIC and ULPP are registered trademarks of Microchip Technology Germany II GmbH & Co. & KG, a subsidiary of Microchip Technology Inc., in other countries. All other trademarks mentioned herein are property of their respective companies. © 1996-2013, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. ISBN: 9781620769300 QUALITY MANAGEMENT SYSTEM Microchip received ISO/TS-16949:2009 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and CERTIFIED BY DNV Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company’s quality system processes and procedures == ISO/TS 16949 == are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001:2000 certified.  1996-2013 Microchip Technology Inc. DS30430D-page 127

Worldwide Sales and Service AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office Asia Pacific Office India - Bangalore Austria - Wels 2355 West Chandler Blvd. Suites 3707-14, 37th Floor Tel: 91-80-3090-4444 Tel: 43-7242-2244-39 Chandler, AZ 85224-6199 Tower 6, The Gateway Fax: 91-80-3090-4123 Fax: 43-7242-2244-393 Tel: 480-792-7200 Harbour City, Kowloon India - New Delhi Denmark - Copenhagen Fax: 480-792-7277 Hong Kong Tel: 91-11-4160-8631 Tel: 45-4450-2828 Technical Support: Tel: 852-2401-1200 Fax: 91-11-4160-8632 Fax: 45-4485-2829 http://www.microchip.com/ support Fax: 852-2401-3431 India - Pune France - Paris Web Address: Australia - Sydney Tel: 91-20-2566-1512 Tel: 33-1-69-53-63-20 www.microchip.com Tel: 61-2-9868-6733 Fax: 91-20-2566-1513 Fax: 33-1-69-30-90-79 Atlanta Fax: 61-2-9868-6755 Japan - Osaka Germany - Munich Duluth, GA China - Beijing Tel: 81-6-6152-7160 Tel: 49-89-627-144-0 Tel: 86-10-8569-7000 Fax: 49-89-627-144-44 Tel: 678-957-9614 Fax: 81-6-6152-9310 Fax: 678-957-1455 Fax: 86-10-8528-2104 Japan - Tokyo Italy - Milan China - Chengdu Tel: 39-0331-742611 Boston Tel: 81-3-6880- 3770 Tel: 86-28-8665-5511 Fax: 39-0331-466781 Westborough, MA Fax: 81-3-6880-3771 Tel: 774-760-0087 Fax: 86-28-8665-7889 Korea - Daegu Netherlands - Drunen Fax: 774-760-0088 China - Chongqing Tel: 82-53-744-4301 Tel: 31-416-690399 Chicago Tel: 86-23-8980-9588 Fax: 82-53-744-4302 Fax: 31-416-690340 Itasca, IL Fax: 86-23-8980-9500 Korea - Seoul Spain - Madrid Tel: 630-285-0071 China - Hangzhou Tel: 82-2-554-7200 Tel: 34-91-708-08-90 Fax: 630-285-0075 Tel: 86-571-2819-3187 Fax: 82-2-558-5932 or Fax: 34-91-708-08-91 Cleveland Fax: 86-571-2819-3189 82-2-558-5934 UK - Wokingham Independence, OH China - Hong Kong SAR Malaysia - Kuala Lumpur Tel: 44-118-921-5869 Tel: 216-447-0464 Tel: 852-2943-5100 Tel: 60-3-6201-9857 Fax: 44-118-921-5820 Fax: 216-447-0643 Fax: 852-2401-3431 Fax: 60-3-6201-9859 Dallas China - Nanjing Malaysia - Penang Addison, TX Tel: 86-25-8473-2460 Tel: 60-4-227-8870 Tel: 972-818-7423 Fax: 86-25-8473-2470 Fax: 60-4-227-4068 Fax: 972-818-2924 China - Qingdao Philippines - Manila Detroit Tel: 86-532-8502-7355 Tel: 63-2-634-9065 Farmington Hills, MI Fax: 86-532-8502-7205 Fax: 63-2-634-9069 Tel: 248-538-2250 Fax: 248-538-2260 China - Shanghai Singapore Tel: 86-21-5407-5533 Tel: 65-6334-8870 Indianapolis Fax: 86-21-5407-5066 Fax: 65-6334-8850 Noblesville, IN Tel: 317-773-8323 China - Shenyang Taiwan - Hsin Chu Fax: 317-773-5453 Tel: 86-24-2334-2829 Tel: 886-3-5778-366 Fax: 86-24-2334-2393 Fax: 886-3-5770-955 Los Angeles Mission Viejo, CA China - Shenzhen Taiwan - Kaohsiung Tel: 949-462-9523 Tel: 86-755-8864-2200 Tel: 886-7-213-7828 Fax: 949-462-9608 Fax: 86-755-8203-1760 Fax: 886-7-330-9305 Santa Clara China - Wuhan Taiwan - Taipei Santa Clara, CA Tel: 86-27-5980-5300 Tel: 886-2-2508-8600 Tel: 408-961-6444 Fax: 86-27-5980-5118 Fax: 886-2-2508-0102 Fax: 408-961-6445 China - Xian Thailand - Bangkok Toronto Tel: 86-29-8833-7252 Tel: 66-2-694-1351 Mississauga, Ontario, Fax: 86-29-8833-7256 Fax: 66-2-694-1350 Canada China - Xiamen Tel: 905-673-0699 Tel: 86-592-2388138 Fax: 905-673-6509 Fax: 86-592-2388130 China - Zhuhai Tel: 86-756-3210040 11/29/12 Fax: 86-756-3210049 DS30430D-page 128  1996-2013 Microchip Technology Inc.

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: M icrochip: PIC16LF84-04I/P PIC16LF83-04I/P PIC16F84A-20E/SO PIC16F84A-20E/SS PIC16F84AT-20/SO PIC16F84AT- 20/SS PIC16F84T-10I/SO PIC16F84A-04I/P PIC16F83-04/P PIC16LF84AT-04/SO PIC16LF84AT-04/SS PIC16LF84AT-04I/SS PIC16LF84AT-04I/SO PIC16F84A-04E/P PIC16LF84A-04I/P PIC16LF83-04I/SO PIC16LF84- 04I/SO PIC16F84A-20/P PIC16F84AT-04/SS PIC16LF83-04/P PIC16F84AT-04/SO PIC16LF83-04/SO PIC16LF84- 04/SO PIC16F83-10I/P PIC16F84-10I/P PIC16F84AT-20E/SO PIC16F84AT-20E/SS PIC16LF84A-04/P PIC16F84A- 04/P PIC16F84A-20I/P PIC16F84-04/P PIC16F83T-04/SO PIC16F84T-04/SO PIC16F84-10/P PIC16F84AT-04I/SO PIC16F84AT-04I/SS PIC16F84A-20I/SS PIC16F84A-20I/SO PIC16F83-10/SO PIC16F84-10/SO PIC16F83T- 04I/SO PIC16F84T-10/SO PIC16F83T-10/SO PIC16LF83T-04I/SO PIC16F84-04I/P PIC16F84A-04/SS PIC16F83- 04I/P PIC16F84A-04/SO PIC16F83-04/SO PIC16F84-04/SO PIC16F83T-10I/SO PIC16F84-10I/SO PIC16F83- 10I/SO PIC16F84A-20/SO PIC16F84A-20/SS PIC16F84AT-04E/SS PIC16F84AT-04E/SO PIC16F84-04I/SO PIC16F83-04I/SO PIC16F83-10/P PIC16F84A-04I/SS PIC16F84A-04I/SO PIC16F84A-04E/SS PIC16LF83T-04/SO PIC16F84A-04E/SO PIC16LF84T-04/SO PIC16LF84-04/P PIC16F84AT-20I/SS PIC16F84AT-20I/SO PIC16F84T- 04I/SO PIC16F84A-20E/P PIC16LF84A-04/SS PIC16LF84A-04/SO PIC16LF84A-04I/SS PIC16LF84T-04I/SO PIC16LF84A-04I/SO