PHP www.vishay.com Vishay Dale Thin Film High Power Thin Film Wraparound Chip Resistor FEATURES • High purity ceramic substrate • Power rating to 2.5 W • Resistance range 10  to 30.1 k • Resistor tolerance to ± 0.1 % • TCR to ± 25 ppm/°C • Flame resistant UL 94 V-0 APPLICATIONS PHP series chip resistors are designed with enlarged • Power supplies backside terminations to reduce the thermal resistance • Power switching between the topside resistor layer and the solder joint on the • Braking system end users circuit board. • Test and measurement equipment • Motor deflection circuits Actual power handling capability is limited by the end user mounting process. As with any high power chip resistor the TYPICAL PERFORMANCE ability to remove the generated heat is critical to the overall performance of the device. ABSOLUTE TCR 25 TOL. 0.1 STANDARD ELECTRICAL SPECIFICATIONS TEST SPECIFICATIONS CONDITIONS Material Nichrome - Resistance Range 10  to 30.1 k - 25 ppm/°C, 50 ppm/°C (standard) TCR: Absolute -55 °C to +125 °C and, 100 ppm/°C Tolerance: Absolute 0.1 %, 0.5 %, 1.0 % and, 5.0 % +25 °C Power Rating: Resistor 0.375 W - 2.5 W (1) Maximum at +70 °C Stability: Absolute R 0.1 % 2000 h at +70 °C Stability: Ratio Not applicable - Voltage Coefficient < 0.1 ppm/V - Working Voltage 75 V to 200 V - Operating Temperature Range -55 °C to +155 °C - Storage Temperature Range -55 °C to +155 °C - Noise < -30 dB - Shelf Life Stability: Absolute ± 0.01 % 1 year at +25 °C COMPONENT RATINGS CASE SIZE POWER RATING (mW) WORKING VOLTAGE (V) RESISTANCE RANGE () 0603 375 (1) 75 10 to 30.1K 0805 625 (1) 100 10 to 30.1K 1206 1000 (1) 200 10 to 30.1K 2512 2500 (1) 200 10 to 30.1K Note (1) Dependent on component mounting by user. ENVIRONMENTAL TESTS (Vishay Performance vs. MIL-PRF-55342 Requirements) LIMITS MIL-PRF-55342 ENVIRONMENTAL TEST TYPICAL VISHAY PERFORMANCE CHARACTERISTIC “E” Resistance Temperature Characteristic ± 25 ppm/°C ± 15 ppm/°C Maximum Ambient Temperature at Rated Wattage +70 °C +70 °C Maximum Ambient Temperature at Power Derating +150 °C +150 °C Thermal Shock ± 0.1 % ± 0.04 % Low Temperature Operation ± 0.1 % ± 0.001 % Short Time Overload ± 0.1 % ± 0.003 % High Temperature Exposure ± 0.1 % ± 0.030 % Resistance to Soldering Heat ± 0.2 % ± 0.007 % Moisture Resistance ± 0.2 % ± 0.002 % Life at +70 °C for 2000 h ± 0.5 % ± 0.100 % Revision: 27-Jun-16 1 Document Number: 60076 For technical questions, contact: thinfilm@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

PHP www.vishay.com Vishay Dale Thin Film DIMENSIONS in inches D W T E L WIDTH THICKNESS TOP PAD BOTTOM PAD CASE SIZE LENGTH W (± 0.005) MIN./MAX. D (± 0.005) E (± 0.005) 0603 0.064 ± 0.006 0.032 0.020 max. 0.012 0.021 0805 0.080 ± 0.006 0.050 0.015/0.033 0.016 0.025 1206 0.126 ± 0.008 0.063 0.015/0.033 0.020 + 0.005/- 0.010 0.040 2512 0.259 + 0.009/- 0.015 0.124 0.015/0.033 0.02 0.050 LAND PATTERN DIMENSIONS in inches 0603 Land Pattern 1206 Land Pattern 0.0920 0.1730 0.0340 0.0710 0.0140 0.0390 0.0220 0.0755 0805 Land Pattern 2512 Land Pattern 0.1050 0.2910 0.0520 0.1260 0.0200 0.0425 0.1090 0.0910 STANDARD MATERIAL SPECIFICATIONS Resistive Element Nichrome Substrate Material Alumina (Al O ) 2 3 Terminations (Tin/Lead) Tin/lead solder over nickel barrier Terminations (Lead (Pb)-free) Tin/silver/copper (Sn96.5Ag3.0Cu0.5) solder over nickel barrier Revision: 27-Jun-16 2 Document Number: 60076 For technical questions, contact: thinfilm@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

PHP www.vishay.com Vishay Dale Thin Film PHP CHIP TEMP. VS. APPLIED POWER PHP CHIP TEMP. VS. APPLIED POWER 5.00 5.00 4.50 0603 - 100 Ω 4.50 0805 - 100 Ω 0603 - 5 kΩ 0805 - 5 kΩ W) 4.00 0603 - 18.8 kΩ W) 4.00 0805 - 20 kΩ er ( 3.50 er ( 3.50 w 3.00 w 3.00 Po 2.50 Po 2.50 d 2.00 d 2.00 e e pli 1.50 pli 1.50 Ap 1.00 Ap 1.00 0.50 0.50 0.00 0.00 70 150 200 70 150 200 Chip Surface Temperature (°C) Chip Surface Temperature (°C) Note Note • Chip surface temperature measured using FLIR SC645 thermal • Chip surface temperature measured using FLIR SC645 thermal imaging system with an approximate test card surface imaging system with an approximate test card surface temperature of 85 °C. temperature of 85 °C. PHP CHIP TEMP. VS. APPLIED POWER PHP CHIP TEMP. VS. APPLIED POWER 5.00 10.00 4.50 1206 - 100 Ω 9.00 2512 - 10 Ω 1206 - 5 kΩ 2512 - 10 kΩ W) 4.00 1206 - 10 kΩ W) 8.00 2512 - 30 kΩ er ( 3.50 er ( 7.00 w 3.00 w 6.00 Po 2.50 Po 5.00 d 2.00 d 4.00 e e pli 1.50 pli 3.00 Ap 1.00 Ap 2.00 0.50 1.00 0.00 0.00 70 150 200 70 150 200 Chip Surface Temperature (°C) Chip Surface Temperature (°C) Notes Notes • Chip surface temperature measured using FLIR A40 thermal imaging system with an approximate test card surface • Chip surface temperature measured using FLIR A40 thermal temperature of 25 °C. imaging system with an approximate test card surface temperature of 25 °C. • Thermal imaging was conducted under ambient conditions resulting in a steady state test card surface temperature of 85 °C Case Size 2512 2512 2512 over the full range of power levels. Resistance • Thermal imaging and load life testing was conducted mounting Value Up to 10  Up to 10 k Up to 30 k one device to 2" x 3" test cards with 2.5 mil copper plating on Temperature Power (W) both surfaces. Thermal vias on 120 mil centers were utilized for heat transfer between surfaces of the test card. 70 2.44 1.81 1.87 150 6.82 4.89 5.19 200 9.33 6.63 7.09 Revision: 27-Jun-16 3 Document Number: 60076 For technical questions, contact: thinfilm@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

PHP www.vishay.com Vishay Dale Thin Film SINGLE PULSE CURVES 1000 100 Ω - 2512 100 Ω - 1206 W)100 er ( w o 10 P e s Pul 1 100 Ω - 0805 100 Ω - 0603 0.1 0.00001 0.0001 0.001 0.01 0.1 1 10 Pulse Duration (s) DERATING CURVE 100 wer 80 o P ed 60 at R of 40 nt e c er 20 P 0 0 70 125 155 Ambient Temperature °C GLOBAL PART NUMBER INFORMATION P H P 0 1 2 0 6 E 1 0 0 2 B B T 1 GLOBAL CASE SUBSTRATE TCR RESISTANCE TOLERANCE TERMINATION PACKAGING MODEL SIZE PHP 0 = Alumina 0603 E = The first 3 digits B = ± 0.1 % B =Wraparound BS = BULK 0805 ± 25 ppm/°C are significant D = ± 0.5 % Sn/Pb solder 100 min., 1 mult 1206 H = figures and the F = ± 1.0 % w/nickel barrier WS = WAFFLE 2512 ± 50 ppm/°C last digit G = ± 2.0 %  100 min., 1 mult K = specifies the J = ± 5.0 % S = Wraparound WI = WAFFLE  ± 100 ppm/°C number of lead (Pb)-free solder  (item single lot zeros to follow. SAC-305 day code) “R” designates RoHS-compliant - e1 100 min., 1 mult the decimal  point. TAPE AND REEL T1 = 1000 min.,  Example: 1000 mult 10R0 = 10  T3 = 300 min., 300 mult 1000 = 100  T5 = 500 min., 500 mult 1001 = 1 k TF = Full reel TS =100 min., 1 mult TI = 100 min., 1 mult  (item single lot date code) TP =100 min., 1 mult  (package unit single lot date) Revision: 27-Jun-16 4 Document Number: 60076 For technical questions, contact: thinfilm@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Legal Disclaimer Notice www.vishay.com Vishay Disclaimer  ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2017 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 08-Feb-17 1 Document Number: 91000