Class X2 Metallized Polyester Film EMI Suppression Capacitors PHE820M, Class X2, 275 VAC Overview Applications Series winding of metallized polyester, encapsulated in Typical applications include worldwide use in self-extinguishing material meeting the requirements electromagnetic interference suppression in all X2 and of UL 94 V–0. across-the-line applications. Benefits • Approvals: ENEC, UL, cUL • Rated voltage: 275 VAC 50/60 Hz • Capacitance range: 0.01 – 2.2 µF • Lead spacing: 15.0 – 37.5 mm • Capacitance tolerance: ±20%, ±10%; ±5% on request • Climatic category: 40/100/56, IEC 60068–1 • Tape and reel in accordance with IEC 60286–2 • RoHS Compliant and lead-free terminations • Operating temperature range of −40°C to +100°C • 100% screening factory test at 2,150 VDC Customer Part Number PHE820 M B 5100 M R17 Capacitance Capacitance Series Rated Voltage (VAC) Lead Spacing (mm) Packaging Code (pF) Tolerance X2, Metallized M = 275 B = 15.0 The last three digits J = ±5% See Ordering Polyester D = 22.5 represent significant K = ±10% Options Table F = 27.5 figures. The first digit M = ±20% R = 37.5 specifies the total number of digits. KEMET Internal Part Number F 720 B D 103 M 275 A Capacitor Capacitance Rated Voltage Series Lead Spacing (mm) Size Code Capacitance Code (pF) Packaging Class Tolerance (VAC) F = Film X2, B = 15.0 See Dimension First two digits represent J = ±5% 275 = 275 See Ordering Metallized D = 22.5 Table significant figures. Third K = ±10% Options Table Polyester F = 27.5 digit specifies number of M = ±20% R = 37.5 zeros. One world. One KEMET © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard F3009_PHE820M_X2_275 • 6/3/2019 1 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com

Class X2 Metallized Polyester Film EMI Suppression Capacitors – PHE820M, Class X2, 275 VAC Ordering Options Table Lead KEMET Legacy Spacing Lead Length Lead and Lead and Type of Leads and Packaging Nominal (mm) Packaging Packaging (mm) Code Code Standard Lead and Packaging Options Bulk (Bag) – Short Leads 6 +0/−1 C R06 Bulk (Bag) – Long Leads 17 +0/−1 A R17 15 Other Lead and Packaging Options Bulk (Bag) – Maximum Length Leads 30 +5/−0 ALW0L R30 Tape & Reel (Standard Reel) H= 18.5 ±0.5 L R17T0 0 Tape & Reel (Large Reel) H= 18.5 ±0.5 P R17T1 0 Ammo Pack H= 16.5 ±0.5 XLAF1 R25XA Native 15 0 formed to 7.5 Tape & Reel (Standard Reel) H= 16.5 ±0.5 XLTF1 R25X2 0 Standard Lead and Packaging Options Bulk (Tray) – Short Leads 6 +0/−1 C R06L2(1) Other Lead and Packaging Options 22.5 Tape & Reel (Standard Reel) H= 18.5 ±0.5 L R17T0 0 Tape & Reel (Large Reel) H= 18.5 ±0.5 P R17T1 0 Pizza Pack 6 +0/−1 Z R06L2(1) Standard Lead and Packaging Options Bulk (Tray) – Short Leads 6 +0/−1 C R06L2(1) 27.5 Other Lead and Packaging Options Tape & Reel (Large Reel) H= 18.5 ±0.5 P R17T1 0 Pizza Pack 6 +0/−1 Z R06L2(1) Standard Lead and Packaging Options Bulk (Tray) – Short Leads 6 +0/−1 C R06L2(1) 37.5 Other Lead and Packaging Options Pizza Pack 6 +0/−1 Z R06L2(1) (1) Please specify Bulk (Tray) or Pizza Packaging. © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard F3009_PHE820M_X2_275 • 6/3/2019 2 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com

Class X2 Metallized Polyester Film EMI Suppression Capacitors – PHE820M, Class X2, 275 VAC Dimensions – Millimeters FRONT VIEW SIDE VIEW L B H d 0.5 LL p KEMET Customer p B H L d Internal Size Nominal Tolerance Nominal Tolerance Nominal Tolerance Nominal Tolerance Nominal Tolerance Size Code Code BD B04 15.0 ±0.4 5.5 Maximum 10.5 Maximum 18.0 Maximum 0.8 ±0.05 BE B05 15.0 ±0.4 5.5 Maximum 12.5 Maximum 18.0 Maximum 0.8 ±0.05 BL B06 15.0 ±0.4 7.5 Maximum 14.5 Maximum 18.0 Maximum 0.8 ±0.05 BJ B10 15.0 ±0.4 6.5 Maximum 12.5 Maximum 18.0 Maximum 0.8 ±0.05 BQ B11 15.0 ±0.4 8.5 Maximum 16.0 Maximum 18.0 Maximum 0.8 ±0.05 DD D13 22.5 ±0.4 6.5 Maximum 14.5 Maximum 26.0 Maximum 0.8 ±0.05 DH D14 22.5 ±0.4 8.0 Maximum 16.0 Maximum 26.0 Maximum 0.8 ±0.05 DM D15 22.5 ±0.4 9.0 Maximum 18.5 Maximum 26.0 Maximum 0.8 ±0.05 DT D16 22.5 ±0.4 11.0 Maximum 21.5 Maximum 26.0 Maximum 0.8 ±0.05 FG F12 27.5 ±0.4 11.5 Maximum 22.5 Maximum 31.5 Maximum 0.8 ±0.05 FM F13 27.5 ±0.4 14.5 Maximum 24.5 Maximum 31.5 Maximum 0.8 ±0.05 FR F14 27.5 ±0.4 17.5 Maximum 28.0 Maximum 31.5 Maximum 0.8 ±0.05 RK R02 37.5 ±0.4 16.5 Maximum 32.0 Maximum 41.0 Maximum 1.0 ±0.05 RM R03 37.5 ±0.4 19.0 Maximum 36.0 Maximum 41.0 Maximum 1.0 ±0.05 Note: See Ordering Options Table for lead length (LL) options. © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard F3009_PHE820M_X2_275 • 6/3/2019 3 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com

Class X2 Metallized Polyester Film EMI Suppression Capacitors – PHE820M, Class X2, 275 VAC Performance Characteristics Rated Voltage 275 VAC 50/60 Hz Capacitance Range 0.01 – 2.2 µF Capacitance Tolerance ±20%, ±10%; ±5% on request Temperature Range -40ºC to +100°C Climatic Category 40/100/56 Approvals ENEC, UL, cUL Maximum Values at +23°C Dissipation Factor 1 kHz 1.0% The 100% screening factory test is carried out at 2,150 VDC. The voltage level is selected to meet the requirements in applicable equipment standards. All electrical characteristics are checked Test Voltage Between Terminals after the test. It is not permitted to repeat this test as there is a risk to damage the capacitor. KEMET is not liable in such case for any failures. Minimum Values Between Terminals Insulation Resistance C ≤ 0.33 µF ≥ 30,000 MΩ C > 0.33 µF ≥ 10,000 MΩ • µF In DC Applications Recommended voltage ≤ 760 VDC Environmental Test Data Test IEC Publication Procedure 1.25 x V VAC 50 Hz, once every hour increase to 1,000 VAC for 0.1 Endurance EN/IEC 60384–14 R second, 1,000 hours at upper rated temperature Vibration IEC 60068–2–6 Test Fc 3 directions at 2 hours each 10 – 55 Hz at 0.75 mm or 98 m/s2 Bump IEC 60068–2–29 Test Eb 1,000 bumps at 390 m/s2 Change of Temperature IEC 60068–2–14 Test Na Upper and lower rated temperature 5 cycles Active Flammability IEC 60384–14 V + 20 surge pulses at 2.5 kV (pulse every 5 seconds) R Passive Flammability IEC 60384–14 IEC 60384–1, IEC 60695–11–5 Needle Flame Test Damp Heat Steady State IEC 60068–2–78 Test Cab +40°C and 93% RH, 56 days © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard F3009_PHE820M_X2_275 • 6/3/2019 4 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com

Class X2 Metallized Polyester Film EMI Suppression Capacitors – PHE820M, Class X2, 275 VAC Approvals Mark Specification File Number EN/IEC 60384–14 SE/0140–12E UL 1414 (up to 1 μF, 85°C, 250 E73869 VAC) CSA – C22.2 No. 1 E73869 (up to 1 μF, 85°C, 250 VAC) UL 1283 (310 VAC) E100117 CSA – C22.2 No. 8 (310 VAC) E100117 Environmental Compliance Table 1 – Ratings & Part Number Reference Maximum Lead dV/dt Capacitance Size Code f KEMET Internal Customer Dimensions in mm Spacing o (V/ Value (µF) (New/Legacy) (MHz) Part Number Part Number B H L (p) µs) 0.010 BD/B04 5.5 10.5 18.0 15 13 100 F720BD103(1)275(2) PHE820MB5100(1)(2) 0.015 BD/B04 5.5 10.5 18.0 15 11 100 F720BD153(1)275(2) PHE820MB5150(1)(2) 0.022 BD/B04 5.5 10.5 18.0 15 9.0 100 F720BD223(1)275(2) PHE820MB5220(1)(2) 0.033 BE/B05 5.5 12.5 18.0 15 7.5 100 F720BE333(1)275(2) PHE820MB5330(1)(2) 0.047 BJ/B10 6.5 12.5 18.0 15 6.5 100 F720BJ473(1)275(2) PHE820MB5470(1)(2) 0.068 BL/B06 7.5 14.5 18.0 15 5.5 100 F720BL683(1)275(2) PHE820MB5680(1)(2) 0.10 BQ/B11 8.5 16.0 18.0 15 4.5 100 F720BQ104(1)275(2) PHE820MB6100(1)(2) 0.10 DD/D13 6.5 14.5 26.0 22.5 4.5 100 F720DD104(1)275(2) PHE820MD6100(1)(2) 0.15 DH/D14 8.0 16.0 26.0 22.5 3.9 100 F720DH154(1)275(2) PHE820MD6150(1)(2) 0.22 DM/D15 9.0 18.5 26.0 22.5 2.7 100 F720DM224(1)275(2) PHE820MD6220(1)(2) 0.33 DT/D16 11.0 21.5 26.0 22.5 2.5 100 F720DT334(1)275(2) PHE820MD6330(1)(2) 0.47 FG/F12 11.5 22.5 31.5 27.5 1.9 100 F720FG474(1)275(2) PHE820MF6470(1)(2) 0.68 FM/F13 14.5 24.5 31.5 27.5 1.6 100 F720FM684(1)275(2) PHE820MF6680(1)(2) 1.0 FR/F14 17.5 28.0 31.5 27.5 1.3 100 F720FR105(1)275(2) PHE820MF7100(1)(2) 1.5 RK/R02 16.5 32.0 41.0 37.5 0.75 100 F720RK155(1)275(2) PHE820MR7150(1)(2) 2.2 RM/R03 19.0 36.0 41.0 37.5 0.65 100 F720RM225(1)275(2) PHE820MR7220(1)(2) Capacitance Size Code Lead Spacing dV/dt KEMET Internal Customer B (mm) H (mm) L (mm) f (MHz) Value (µF) (New/Legacy) (p) o (V/µs) Part Number Part Number (1) M = ±20%, K = ±10%, J = ±5% on request. (2) Insert ordering code for lead type and packaging. See Ordering Options Table for available options. © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard F3009_PHE820M_X2_275 • 6/3/2019 5 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com

Class X2 Metallized Polyester Film EMI Suppression Capacitors – PHE820M, Class X2, 275 VAC Soldering Process The implementation of the RoHS directive has resulted in the selection of SnAgCu (SAC) alloys or SnCu alloys as primary solder. This has increased the liquidus temperature from that of 183ºC for SnPb eutectic alloy to 217 – 221°C for the new alloys. As a result, the heat stress to the components, even in wave soldering, has increased considerably due to higher pre-heat and wave temperatures. Polypropylene capacitors are especially sensitive to heat (the melting point of polypropylene is 160 – 170°C). Wave soldering can be destructive, especially for mechanically small polypropylene capacitors (with lead spacing of 5 – 15 mm), and great care has to be taken during soldering. The recommended solder profiles from KEMET should be used. Please consult KEMET with any questions. In general, the wave soldering curve from IEC Publication 61760–1 Edition 2 serves as a solid guideline for successful soldering. Please see Figure 1. Reflow soldering is not recommended for through-hole film capacitors. Exposing capacitors to a soldering profile in excess of the above the recommended limits may result to degradation or permanent damage to the capacitors. Do not place the polypropylene capacitor through an adhesive curing oven to cure resin for surface mount components. Insert through-hole parts after the curing of surface mount parts. Consult KEMET to discuss the actual temperature profile in the oven, if through-hole components must pass through the adhesive curing process. A maximum two soldering cycles is recommended. Please allow time for the capacitor surface temperature to return to a normal temperature before the second soldering cycle. Manual Soldering Recommendations Wave Soldering Recommendations 300 Following is the recommendation for manual 2 +3 seconds maximum soldering with a soldering iron. 260°C 250 First wave Second wave Recommended Soldering Temperature 200 C) ∆T < 150°C Cooling 345000 erature (°150 Preheating ccaa 23.°5C°/Cs/esceocnodnd typical mperature (°C)235000 Temp100 Tpreheat 115°C max 100°C Typical ca 5°C/second Soldering Iron Bit Te112050000 500 0 40 80 120 160 200 240 Time (s) 50 0 0 1 2 3 4 5 6 7 8 Soldering Time (seconds) The soldering iron tip temperature should be set at 350°C (+10°C maximum) with the soldering duration not to exceed more than 3 seconds. © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard F3009_PHE820M_X2_275 • 6/3/2019 6 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com

Class X2 Metallized Polyester Film EMI Suppression Capacitors – PHE820M, Class X2, 275 VAC Soldering Process cont. Wave Soldering Recommendations cont'd 1. The table indicates the maximum set-up temperature of the soldering process Figure 1 Maximum Maximum Preheat Peak Soldering Temperature Dielectric Temperature Film Material Capacitor Capacitor Capacitor Capacitor Capacitor Pitch Pitch Pitch Pitch Pitch ≤ 10 mm = 15 mm > 15 mm ≤ 15 mm > 15 mm Polyester 130°C 130°C 130°C 270°C 270°C Polypropylene 100°C 110°C 130°C 260°C 270°C Paper 130°C 130°C 140°C 270°C 270°C Polyphenylene 150°C 150°C 160°C 270°C 270°C Sulphide 2. The maximum temperature measured inside the capacitor: Set the temperature so that inside the element the maximum temperature is below the limit: Maximum temperature Dielectric Film Material measured inside the element Polyester 160°C Polypropylene 110°C Paper 160°C Polyphenylene Sulphide 160°C Temperature monitored inside the capacitor. Selective Soldering Recommendations Selective dip soldering is a variation of reflow soldering. In this method, the printed circuit board with through-hole components to be soldered is preheated and transported over the solder bath as in normal flow soldering without touching the solder. When the board is over the bath, it is stopped and pre-designed solder pots are lifted from the bath with molten solder only at the places of the selected components, and pressed against the lower surface of the board to solder the components. The temperature profile for selective soldering is similar to the double wave flow soldering outlined in this document, however, instead of two baths, there is only one bath with a time from 3 to 10 seconds. In selective soldering, the risk of overheating is greater than in double wave flow soldering, and great care must be taken so that the parts are not overheated. © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard F3009_PHE820M_X2_275 • 6/3/2019 7 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com

FILM WINDING SCHEME OPTIONS Single-sided Metallized Polypropylene Film Double-sided Metallized Polyester Film Polypropylene Double-sided Film Dielectric Metallized Single-sided Single-sided Double-sided Polypropylene Polyester Carrier Metallized Metallized Metallized Film Dielectric Film Polypropylene Polypropylene Polyester Single-sided Film Film Carrier Metallized Film Polypropylene Film 1 Section 2 Sections 1 Section 2 Sections Polypropylene Double-sided Film Dielectric Metallized Single-sided Single-sided Double-sided Polypropylene Polyester Carrier Class X2 Metallized Metallized Metallized Film Dielectric Film Polypropylene Polypropylene Polyester Single-sided Metallized Polyester Film EMI SuppFrilemssion Capacitors – PHE820M, Class X2, 275 FViAlmC Carrier Metallized Film Polypropylene Film Construction 3 Sections 4 Sections 3 Sections 4 Sections Detailed Cross Section Molded Plastic Single-sided Metallized Molded Plastic Self-Extinguishing Case Polyester Film Case Resin (First Layer) Single-sided Metallized Polyester Film (Second Layer) Metallized Impregnated Paper Metallized Polyphenylene Margin Polypropylene Film/Foil Sulfide Film (SMR) Single-sided Margin Metallized Metal Foil Metal Foil Polypropylene Metallized Polypropylene Film Impregnated MetallizMede tPaol lyCpohnetnaycl-t Film Dielectric Metal Contact Paper eVnaec Suuumlfi-dEev LaFapiloymrea rwteitdh Polypropylene Film Dielectric Layer Aluminum Electrodes Margin 1 Section 1 Section 1 Section 2 Sections Leads Single-sided Metallized Polyester Film Winding Scheme AXIAL - Polypropylene Film/Foil Single-sided Polypropylene Single-sided Metallized Film Dielec- Metallized Polyester tric Polypropylene Film Film Polypropylene 1 Section Metal Foil Metal Foil Film Dielectric 1 Section 2 Sections AXIAL - Single-sided Metallized AXIAL - Single-sided Metallized AXIAL - Double-sided Polypropylene Film Polyester Film Metallized Polyester Film Single-sided Single-sided Double-sided Polypropylene Metallized Metallized Metallized Film Dielectric Polypropylene Polyester Polyester Carrier Film Film Film Single-sided Metallized Polypropylene Film 1 Section 1 Section 2 Sections © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard F3009_PHE820M_X2_275 • 6/3/2019 8 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com

Class X2 Metallized Polyester Film EMI Suppression Capacitors – PHE820M, Class X2, 275 VAC Marking FRONT TOP RIFA Logo Series Approval Mark Rated Voltage IEC Climatic Category Capacitance Manufacturing Capacitance Tolerance Date Code Approval Mark © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard F3009_PHE820M_X2_275 • 6/3/2019 9 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com

Class X2 Metallized Polyester Film EMI Suppression Capacitors – PHE820M, Class X2, 275 VAC Packaging Quantities KEMET Legacy Bulk Bulk Standard Large Standard Lead Thickness Height Length Ammo Size Size Short Long Reel Reel Pizza Reel Spacing (mm) (mm) (mm) Formed Code Code Leads Leads 360 mm 500 mm Formed BD B04 5.5 10.5 18 1,000 800 600 1,200 550 570 BE B05 5.5 12.5 18 1,000 800 600 1,200 550 570 BL B06 7.5 14.5 18 800 400 400 800 350 378 BJ B10 6.5 12.5 18 1,000 600 500 1,000 450 480 BQ B11 8.5 16 18 600 400 400 800 350 324 15 BM B12 8 15 18 600 400 400 800 350 351 BV B14 9.5 17.5 18 500 300 350 700 250 297 BG B15 6 12 18 1,000 800 500 1,000 450 520 BY B16 11 19 18 450 250 300 600 250 252 BU B17 13 12.5 18 400 300 250 500 200 216 DD D13 6.5 14.5 26.5 234 300 600 440 DH D14 8 16 26.5 186 250 500 352 DM D15 9 18.5 26.5 308 250 500 308 DT D16 11 21.5 26.5 253 200 400 253 22.5 DF D17 7 16.5 26.5 216 300 600 396 DR D18 10.5 19 26.5 264 200 400 264 DY D19 15.5 24.5 26.5 176 110 250 176 DW D20 13.5 23 26.5 209 160 300 209 FK F03 13.5 23 31.5 171 250 171 FE F11 10.5 20.5 31.5 216 350 216 FG F12 11.5 22.5 31.5 198 300 198 FM F13 14.5 24.5 31.5 153 250 153 FR F14 17.5 28 31.5 126 126 27.5 FS F15 19 29 31.5 117 117 FV F16 21 30 31.5 108 108 FH F17 21 12.5 31.5 108 108 FT F18 31 18.5 31.5 72 72 FQ F19 27.5 16 31.5 81 81 RK R02 16.5 32 41 105 105 RM R03 19 36 41 91 91 RH R04 15 26 41 119 119 37.5 RF R05 13 24 41 140 140 RP R06 21 38 41 84 84 RS R08 28 43 41 54 54 © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard F3009_PHE820M_X2_275 • 6/3/2019 10 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com

Class X2 Metallized Polyester Film EMI Suppression Capacitors – PHE820M, Class X2, 275 VAC Lead Taping & Packaging (IEC 60286–2) Lead Spacing 5 mm Lead Spacing 7.5 mm ∆p ∆p ∆p ∆p ∆h ∆h ∆h ∆h H1 F W2 H1 F W2 H0 W0 W1 H0 W0 W1 W W P0 P1 D0 P0 D0 t P1 t Lead Spacing 10 – 15 mm Lead Spacing 22.5 – 27.5 mm ∆p ∆p ∆p ∆p ∆h ∆h ∆h ∆h H1 F W2 H1 F W2 H H 0 W0 W1 0 W0 W1 W W P P D P P D 1 0 0 0 1 0 t t Taping Specification Dimensions in mm Standard IEC 60286–2 Lead Spacing +0.6/−0.1 F 5.0 7.5 10.0 15.0 22.5 27.5 F Carrier Tape Width ±0.5 W 18.0 18.0 18.0 18.0 18.0 18.0 18+1/−0.5 Hold-Down Tape Width ±0.3 W 9.0 9.0 9.0 9.0 9.0 9.0 0 Position of Sprocket Hole ±0.5 W 9.0 9.0 9.0 9.0 9.0 9.0 9+0.75/−0.5 1 Distance Between Tapes Maximum W 3.0 3.0 3.0 3.0 3.0 3.0 3.0 2 Sprocket Hole Diameter ±0.2 D 4.0 4.0 4.0 4.0 4.0 4.0 4.0 0 Feed Hole Lead Spacing ±0.3 P (1) 12.7 12.7 12.7 12.7 12.7 12.7 12.7 0 Distance Lead – Feed Hole ±0.7 P 3.85 3.75 7.7 5.2 7.8 5.3 P1 1 Deviation Tape – Plane Maximum ∆p 1.3 1.3 1.3 1.3 1.3 1.3 1.3 Lateral Deviation Maximum ∆h 2.0 2.0 2.0 2.0 2.0 2.0 2.0 Total Thickness ±0.2 t 0.7 0.7 0.7 0.7 0.9MAX 0.9MAX 0.9MAX Sprocket Hole/Cap Body Nominal H(2) 18.5±0.5 18.5±0.5 18.5±0.5 18.5±0.5 18.5±0.5 18.5±0.5 18+2/−0 0 Sprocket Hole/Top of Cap Body H(3) 32.0 31.0 43.0 43.0 58.0 58.0 58MAX 1 (1) Cumulative lead spacing error. (2) 16.5 mm available on request. (3) Depending on case size. © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard F3009_PHE820M_X2_275 • 6/3/2019 11 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com

Class X2 Metallized Polyester Film EMI Suppression Capacitors – PHE820M, Class X2, 275 VAC Lead Taping & Packaging (IEC 60286–2) cont'd Ammo Specifi cations Dimensions (mm) Series H W T R4x, R4x+R, R7x, RSB H F5A, F5B, F5D 360 340 59 F6xx, F8xx PHExxx, PMExxx, PMRxxx, 330 330 50 SMR & PFR W T Reel Specifi cations Dimensions (mm) Series D H W R4x, R4x+R, R7x, RSB 355 30 F5A, F5B, F5D 55 (Max) D H 500 25 F6xx, F8xx PHExxx, PMExxx, PMRxxx, 360 30 46 (Max) SMR & PFR 500 Manufacturing Date Code (IEC–60062) W Y = Year, Z = Month Year Code Month Code 2010 A January 1 2011 B February 2 2012 C March 3 2013 D April 4 2014 E May 5 2015 F June 6 2016 H July 7 2017 J August 8 2018 K September 9 2019 L October O 2020 M November N 2021 N December D 2022 P 2023 R 2024 S 2025 T 2026 U 2027 V 2028 W 2029 X 2030 A © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard F3009_PHE820M_X2_275 • 6/3/2019 12 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com

Class X2 Metallized Polyester Film EMI Suppression Capacitors – PHE820M, Class X2, 275 VAC KEMET Electronics Corporation Sales Offi ces For a complete list of our global sales offi ces, please visit www.kemet.com/sales. Disclaimer All product specifi cations, statements, information and data (collectively, the “Information”) in this datasheet are subject to change. The customer is responsible for checking and verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed. All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied. Statements of suitability for certain applications are based on KEMET Electronics Corporation’s (“KEMET”) knowledge of typical operating conditions for such applications, but are not intended to constitute – and KEMET specifi cally disclaims – any warranty concerning suitability for a specifi c customer application or use. The Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by KEMET with reference to the use of KEMET’s products is given gratis, and KEMET assumes no obligation or liability for the advice given or results obtained. Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. Although all product–related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicted or that other measures may not be required. KEMET is a registered trademark of KEMET Electronics Corporation. © KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard F3009_PHE820M_X2_275 • 6/3/2019 13 Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: K EMET: PHE820MD6220MR06L2 PHE820MF6470MR06L2 PHE820MF7100MR06L2 PHE820MR7220MR06L2 PHE820MB6100MR17 PHE820MF7100KR06L2 PHE820MB5150MR17 PHE820MB5220MR17 PHE820MB5330MR17 PHE820MB5680MR17 PHE820MD6100MR06L2 PHE820MD6150KR06L2 PHE820MD6150MR06L2 PHE820MD6330MR06L2 PHE820MF6680MR06L2 PHE820MR7150MR06L2 PHE820MR7220MR30L2 PHE820MB5100MR17 PHE820MB5470MR17 PHE820MB6100KR17 PHE820MF7100MR30L2 PHE820MR7220KR06L2 PHE820MF6470MR17L2 PHE820MB5100MR17T0 PHE820MB5470MR17T0 PHE820MF7100MR17L2 F720BQ104M275L F720DM224K275C PHE820MB5470KR17 F720DD104K275C