DataSheet PCB Mount PF Series • SIP SSR • Ratings to 25A (forced air) @ 480 VAC • SCR output for heavy industrial loads • AC or DC control • Zero-crossing (resistive loads) or random-fire (inductive loads) output PRODUCT SELECTION Control Voltage 25 A 25 A 25 A 3-15 VDC PF240D25 4-15 VDC PF380D25 PF480D25 15-32 VDC PFE240D25 PFE380D25 PFE480D25 18-36 VAC PFE240A25 90-140 VAC PF240A25 AVAILABLE OPTIONS Operational Voltage Output Type 240: 12-280 VAC Operational Current Blank: Normally Open 380: 48-530 VAC 25: 25 Amps -B: Normally Closed Series 480: 48-660 VAC (PF480D25 only) PF E 240 D 25 R -B Control Voltage Control Input Type Switching Mode Blank: 3-15 VDC D: DC Input Blank: Zero Voltge Turn-On (240,D suffix only) A: AC Input R: Random Turn-On 4-15 VDC (380/480,D suffix only) 90-140 VAC (A suffix only) E: 15-32 VDC (D suffix only) 18-36 VAC (A suffix only) Required for valid part number For options only and not required for valid part number OUTPUT SPECIFICATIONS (1) Description PF240 PF3 80 PF480 Operating Voltage (47-63Hz) [Vrms] 12-280 48-530 48-660 Transient Overvoltage [Vpk] 600 1200 1200 Maximum Off-State Leakage Current @ Rated Voltage [mArms] 0.1 0.1 0.1 Minimum Off-State dv/dt @ Maximum Rated Voltage [V/μsec] (2) 500 500 500 Maximum Load Current (Convection Air) [Arms] (3) 10 10 10 Maximum Load Current (Forced Air) [Arms] (3) 25 25 25 Minimum Load Current [Arms] 0.06 0.06 0.06 Maximum Surge Current (16.6ms) [Apk] 250 250 250 Maximum On-State Voltage Drop @ Rated Current [Vpk] 1.6 1.6 1.6 Maximum I²t for fusing (8.3 msec) [A² sec] 260 260 260 Minimum Power Factor (with Maximum Load) 0.5 0.5 0.5 FDE-07-01 REV. A Do not forget to visit us at: www.crydom.com Copyright © 2017 Crydom Inc. Specifications subject to change without notice.

DataSheet PCB Mount INPUT SPECIFICATIONS (1) Description PF240D25 PF380D/480D PFExxxD25 PF240A25 PFE240A25 Control Voltage Range [VDC] 3-15 VDC 4-15 VDC 15-32 VDC 90-140 VAC 18-36 VAC Maximum Turn On Voltage 3.0 VDC 4.0 VDC 15.0 VDC 90.0 Vrms 18.0 Vrms Minimum Turn-Off Voltage 1.0 VDC 1.0 VDC 1.0 VDC 10.0 Vrms 2.0 Vrms Typical Input Current @ Nominal Voltage 15 mAdc 15 mAdc 15 mAdc 10 mAdc 10 mAdc Nominal Input Impedance 300 Ohm 240 Ohm 1500 Ohm 14.1 k Ohm 2.1 k Ohm Maximum Turn-On Time [msec] (4) 1/2 Cycle 1/2 Cycle 1/2 Cycle 10 10 Maximum Turn-Off Time [msec] 1/2 Cycle 1/2 Cycle 1/2 Cycle 40 40 GENERAL SPECIFICATIONS Description Parameters Dielectric Strength, Input/Output (50/60Hz) 4000 Vrms Minimum Insulation Resistance (@ 500 V DC) 109 Ohms Maximum Capacitance, Input/Output 8 pF Ambient Operating Temperature Range -30ºC to 80ºC Ambient Storage Temperature Range -30ºC to 125ºC Weight (typical) 1.02 oz. (29g) Encapsulation Thermally Conductive Epoxy GENERAL NOTES 1) All parameters at 25°C unless otherwise specified. 2) Off-State dv/dt test method per EIA/NARM standard RS-443, paragraph 13.11.1 3) Heatsink temperature 85°C Maximum for 25A forced air cooling. 4) Turn-On Time for Random Turn-On versions 0.1 msec (DC Control Models) WIRING DIAGRAM TRIGGER CIRCUIT TRIGGER CIRCUIT AC/DC Converter 4 3 2 1 4 3 V2 1 -DC +DC AC AC B LOA LOA A B LOA LOA A D D D D AC AC AC AC Load can be wired in location A or B Load can be wired in location A or B Do not forget to visit us at: www.crydom.com Copyright © 2017 Crydom Inc. Specifications subject to change without notice.

DataSheet PCB Mount THERMAL DERATE INFORMATION 10 25 S) S) P P M 8 M 20 A A T ( T ( N 6 N 15 E E R R UR 4 UR 10 C C D D A 2 A 5 O O L L 0 0 10 20 30 40 50 60 70 80 0 20 40 60 80 100 120 140 AMBIENT TEMPERATURE (ºC) HEATSINK TEMPERATURE (˚C) FIG.1 Convection Cooling FIG.2 Forced Air Cooling MECHANICAL SPECIFICATIONS Tolerances: ±0.02 in / 0.5 mm All dimensions are in: inches [millimeters] 1.6 TYP. (38.1) 1.35 MAX (34.3) .05 (1.3) 1.6 TYP. (38.1) AGENCY APPROVALS Agency Approvals Designed in accordance with the requirements of IEC 62314 E116950 REG.-Nr. 70938 (240 V, 380 V, DC Control Only) Rev. 081017 ECN 20296 Do not forget to visit us at: www.crydom.com Copyright © 2017 Crydom Inc. Specifications subject to change without notice.

DataSheet PCB Mount DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / 危险 HAZARD OF RIESGO DE RISQUE DE GEFAHR EINES RISCHIO DI 存在电击、 ELECTRIC DESCARGA DESCHARGE ELEKTRISCHE SCOSSA 爆炸或电弧 SHOCK, ELECTRICA O ELECTRIQUE N SCHLAGES ELETTRICA O 闪烁危险 EXPLOSION, EXPLOSION. OU EXPLOSION ODER EINER DELL’ESPLOSIONE. OR ARC FLASH. • Desconectar • Eteindre EXPLOSION. • Spenga tutta • 在操作此设 • Disconnect all todos los toutes les • Stellen Sie l'alimentazione 备之前请先 power before suministros de sources jeglichen che fornisce 关闭电源。 installing or energia a este d'énergie de Strom ab, der questa working with equipo antes cet appareil dieses Gerät apparecchiatura 若不遵守这些说明， this equipment. de trabajar avant de versorgt, bevor prima di lavorare con este equipo. travailler Sie an dem a questa 可能会导致严重的 • Verify all dessus de cet Gerät Arbeiten apparecchiatura 人身伤害甚至死亡。 connections • Verificar todas appareil durchführen and replace all las conexiones • Verificare tutti • Vor dem covers before y colocar todas • Vérifier tous i collegamenti Drehen auf turning on las tapas antes connections, et e sostituire Energie alle power. de energizer remettre tous tutte le coperture Anschlüsse el equipo. couverts en prima Failure to follow olace avant de überprüfen dell’accensione these El mettre sous und alle instructions will incumplimiento Abdeckungen L'omissione di result in death de estas De non-suivi de ersetzen. queste istruzioni or serious injury. instrucciones ces instructions Unterlassung provocherà la puede provocar provoquera la dieser morte o la muerte o mort ou des Anweisungen lesioni serie lesiones serias. lésions sérieuses können zum sérieuses. Tode oder zu schweren Verletzungen führen. WARNING / AVERTISSEMENT / WARNUNG /ADVERTENCIA / AVVERTENZA / 警告 RISK OF MATERIAL DAMAGE AND HOT RISQUE DE DOMMAGE MATERIEL ET DE GEFAHR VON MATERIALSCHÄDEN UND ENCLOSURE SURCHAUFFE DU BOITIER GEHÄUSEERHITZUNG • The product's side panels may be hot, allow • Les panneaux latéraux du produit peuvent être • Die Seitenwände können heiß sein. Lassen Sie the product to cool before touching. chauds. Laisser le produit refroidir avant de le das Produkt abkühlen, bevor Sie es berühren. • Follow proper mounting instructions including toucher. • Beachten Sie die Montageanweisungen, torque values. • Respecter les consignes de montage, et • Führen Sie keine Flüssigkeiten oder • Do not allow liquids or foreign objects to enter notamment les couples de serrage. Fremdkörper in das Produkt ein. this product. • Ne pas laisser pénétrer de liquide ni de corps étrangers à l'intérieur du produit. Le non-respect de cette directive peut entraîner, Die Nichtbeachtung dieser Anweisung kann Failure to follow these instructions can result in des lésions corporelles graves ou des Körperverletzung oder Materialschäden serious injury, or equipment damage. dommages matériels. zur Folge haben. RIESGO DE DAÑOS MATERIALES Y DE 材料损坏和高温外壳的危险性 RISCHIO DI DANNI MATERIALI E D'INVOLUCRO SOBRECALENTAMIENTO DE LA UNIDAD CALDO • 产品的一侧面板可能很热，在其冷却前请 • Los paneles laterales del producto pueden • I pannelli laterali dell'apparecchio possono 不要触碰。 estar calientes. Esperar que el producto se scottare; lasciar quindi raffreddare il prodotto • 遵照正确的安装说明，包括扭矩值。 enfríe antes de tocarlo. • Respetar las instrucciones de montaje, y en prima di toccarlo. • 请勿让液体及其他异物进入本产品。 • Seguire le istruzioni di montaggio corrette. particular los pares de apretado. • Non far entrare liquidi o oggetti estranei in questo • No dejar que penetren líquidos o cuerpos apparecchio. extraños en el producto. La mancata osservanza di questa precauzione può 如不能正确执行这些操作说明， Si no se respetan estas precauciones pueden causare gravi rischi per l'incolumità personale o 极有可能造成严重人体伤害或者设备的损坏。 producirse graves lesiones, daños materiales. danni alle apparecchiature. Do not forget to visit us at: www.crydom.com Copyright © 2017 Crydom Inc. Specifications subject to change without notice.

DataSheet PCB Mount ANNEX - ENVIRONMENTAL INFORMATION The environmental information disclosed in this annex including the EIP Pollution logo are in compliance with People’s Republic of China Electronic Industry Standard SJ/T11364 – 2006, Marking for Control of Pollution Caused by Electronic Information Products. Part Toxic or hazardous Substance and Elements Name Lead Mercury Cadmium Hexavalent Polybrominated Polybrominated (Pb) (Hg) (Cd) Chromium biphenyls diphenyl ethers (Cr (VI)) (PBB) (PBDE) Semiconductor die Solder 附件 - 环保信息 此附件所标示的包括电子信息产品污染图标的环保信息符合中华人民共和国电子行业标准 SJ/T11364 - 2006, 电子信息产品污染控制标识要求。 部件 有毒有害物质或元素 名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr (VI)) (PBB) (PBDE) 半导体芯片 焊接点 50 Do not forget to visit us at: www.crydom.com Copyright © 2017 Crydom Inc. Specifications subject to change without notice.

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: S ensata: PF240D25R PF240A25 PFE240D25R PF240D25 PFE240D25 PF240A25R PF380D25 PF380D25R PF480D25 PF480D25R PFE240A25 PFE240A25R PFE380D25 PFE380D25R PFE480D25 PFE480D25R