CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS PCK Chip Type, Ultra-low ESR Ultra-low ESR, Higher Capacitance, High ripple current. Load life of 2000 hours at 105°C. SMD type : Lead free reflow soldering condition at 260°C peak correspondence. Compliant to the RoHS directive (2011/65/EU,(EU)2015/863). AEC-Q200 compliant. Please contact us for details. PCJ Low ESR PCK Specifications Item Performance Characteristics Category Temperature Range –55 to +105°C Rated Voltage Range 2.5 to 6.3V Rated Capacitance Range 220 to 2200µF Capacitance Tolerance ±20% at 120Hz, 20°C Tangent of loss angle (tan δ) Less than or equal to the specified value at 120Hz, 20°C ESR ( 1) Less than or equal to the specified value at 100kHz, 20°C Leakage Current ( 2) Less than or equal to the specified value . After 2 minutes' application of rated voltage at 20°C Temperature Characteristics Z+105°C / Z+20°C 1.25 (100kHz) (Max.Impedance Ratio) Z–55°C / Z+20°C 1.25 Capacitance change Within ± 20% of the initial capacitance value ( 3) The specifications listed at right shall be met when the tan δ 150% or less than the initial specified value Endurance capacitors are restored to 20°C after the rated voltage is ESR ( 1) 150% or less than the initial specified value applied for 2000 hours at 105°C. Leakage current ( 2) Less than or equal to the initial specified value Capacitance change Within ± 20% of the initial capacitance value ( 3) The specifications listed at right shall be met when the Damp Heat tan δ 150% or less than the initial specified value capacitors are restored to 20°C after the rated voltage is (Steady State) applied for 1000 hours at 60°C, 90% RH. ESR ( 1) 150% or less than the initial specified value Leakage current ( 2) Less than or equal to the initial specified value After soldering the capacitor under the soldering conditions prescribed here, the capacitor shall meet the specifications listed at Capacitance change Within ± 10% of the initial capacitance value ( 3) right. tan δ 130% or less than the initial specified value Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec. ESR ( 1) 130% or less than the initial specified value The duration for over +230°C temperature at capacitor surface shall Leakage current ( 2) Less than or equal to the initial specified value Resistance to not exceed 60 seconds. Soldering Heat In case peak temperature is 250°C or less, reflow soldering shall be two times maximum. In case peak temperature is 260°C or less, reflow soldering shall be once. Measurement for solder temperature profile shall be made at the capacitor top. Marking Navy blue print on the case top 1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120 minutes at 105°C. 3 Initial value : The value before test of examination of resistance to soldering. Dimensions Type numbering system (Example : 6.3V 220µF) Positive Plastic platform X. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Capacitance Lot No. 0.3MAX. C±0.2 MA P C K 0 J 2 2 1 MC O 1 G S 5 0. CK220j941 D±0.5φ B±0.2 E A±0.2 CToanpfiignugr actoiodne Capacitance tolerance (±20%) Series Voltage (j:6.3v) L+-00..41 H Negative Rated capacitance (220µF) Rated voltage (6.3V) Series name Type (mm) Size φ6.3 × 6L φ8 × 7L φ10 × 8L φ10 × 10L φD 6.3 8.0 10.0 10.0 L 5.9 6.9 7.9 9.9 A 7.3 9.0 11.0 11.0 B 6.6 8.3 10.3 10.3 Voltage C 6.6 8.3 10.3 10.3 Frequency coefficient of rated ripple current V 2.5 4 6.3 E 2.1 3.2 4.6 4.6 0 Frequency0/ 120Hz 1kHz 10kHz 100kHz or more H 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 Code e g j Coefficient 0.05 0.30 0.70 1.00 Dimension table in next page. 43

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS PCK Dimensions Rated Voltage ESR Rated Ripple Surge Voltage Rated Capacitance Case Size Leakage Current (V) tan δ (mΩ) (mArms) Part Number (V) (µF) φD × L (mm) (µA) (code) (at 100kHz 20°C) (105°C/100kHz) 390 6.3 × 6 0.12 293 10 3900 PCK0E391MCO1GS 560 8 × 7 0.12 420 9 4500 PCK0E561MCO1GS 2.5 2.8 680 8 × 7 0.12 510 9 4500 PCK0E681MCO1GS (0E) 1200 10 × 8 0.12 900 9 5000 PCK0E122MCO1GS 2200 10 × 10 0.12 1650 8 6000 PCK0E222MCO1GS 330 6.3 × 6 0.12 396 10 3900 PCK0G331MCO1GS 470 8 × 7 0.12 564 9 4500 PCK0G471MCO1GS 4 4.6 560 8 × 7 0.12 672 9 4500 PCK0G561MCO1GS (0G) 1000 10 × 8 0.12 1200 9 5000 PCK0G102MCO1GS 1800 10 × 10 0.12 2160 8 6000 PCK0G182MCO1GS 220 6.3 × 6 0.12 416 10 3900 PCK0J221MCO1GS 330 8 × 7 0.12 624 9 4500 PCK0J331MCO1GS 6.3 7.2 390 8 × 7 0.12 737 9 4500 PCK0J391MCO1GS (0J) 820 10 × 8 0.12 1550 9 5000 PCK0J821MCO1GS 1500 10 × 10 0.12 2835 8 6000 PCK0J152MCO1GS Rated ripple current (mArms) at 105°C 100kHz Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please refer to page 3 for the minimum order quantity. 44

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: N ichicon: PCK0E122MCO1GS PCK0E222MCO1GS PCK0E391MCO1GS PCK0E561MCO1GS PCK0E681MCO1GS PCK0G102MCO1GS PCK0G182MCO1GS PCK0G331MCO1GS PCK0G471MCO1GS PCK0G561MCO1GS PCK0J152MCO1GS PCK0J221MCO1GS PCK0J331MCO1GS PCK0J391MCO1GS PCK0J821MCO1GS