CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS PCGChip Type, Higher Capacitance Higher Capacitance, Low ESR, High ripple current. Load life of 2000 hours at 105°C. SMD type : Lead free reflow soldering condition at PCG 260°C peak correspondence. Compliant to the RoHS directive (2011/65/EU). AEC-Q200 compliant. Please contact us for details. Higher Capacitance PCF Specifications Item Performance Characteristics Category Temperature Range –55 to +105°C Rated Voltage Range 2.5 to 16V Rated Capacitance Range 47 to 4700µF Capacitance Tolerance ±20% at 120Hz, 20°C Tangent of loss angle (tan δ) Less than or equal to the specified value at 120Hz, 20°C ESR ( 1) Less than or equal to the specified value at 100kHz, 20°C Leakage Current ( 2) Less than or equal to the specified value. After 2 minutes' application of rated voltage at 20°C Temperature Characteristics Z+105°C / Z+20°C 1.25 (100kHz) (Max.Impedance Ratio) Z–55°C / Z+20°C 1.25 Capacitance change Within ± 20% of the initial capacitance value ( 3) The specifications listed at right shall be met when the tan δ 150% or less than the initial specified value Endurance capacitors are restored to 20°C after the rated voltage is ESR ( 1) 150% or less than the initial specified value applied for 2000 hours at 105°C. Leakage current ( 2) Less than or equal to the initial specified value Capacitance change Within ± 20% of the initial capacitance value ( 3) The specifications listed at right shall be met when the Damp Heat tan δ 150% or less than the initial specified value capacitors are restored to 20°C after the rated voltage is (Steady State) applied for 1000 hours at 60°C, 90% RH. ESR ( 1) 150% or less than the initial specified value Leakage current ( 2) Less than or equal to the initial specified value After soldering the capacitor under the soldering conditions prescribed here, the capacitor shall meet the specifications listed at Capacitance change Within ± 10% of the initial capacitance value ( 3) right. tan δ 130% or less than the initial specified value Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec. ESR ( 1) 130% or less than the initial specified value The duration for over +230°C temperature at capacitor surface shall Leakage current ( 2) Less than or equal to the initial specified value Resistance to not exceed 60 seconds. Soldering Heat In case peak temperature is 250°C or less, reflow soldering shall be two times maximum. In case peak temperature is 260°C or less, reflow soldering shall be once. Measurement for solder temperature profile shall be made at the capacitor top and the terminal. Marking Navy blue print on the case top 1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120 minutes at 105°C. 3 Initial value : The value before test of examination of resistance to soldering. Dimensions Type numbering system (Example : 6.3V 470µF) Positive Plastic platform X. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Capacitance Lot No. 0.3MAX. C±0.2 MA P C G 0 J 4 7 1 M C L 1 G S 5 0. CG470j841 D±0.5φ B±0.2 E A±0.2 CToanpfiignugr acotiodne Capacitance tolerance (±20%) Series Voltage (j:6.3v) L+-00..41 H Negative Rated capacitance (470µF) Rated voltage (6.3V) Series name (mm) Size φ5 × 6L φ6.3 × 6L φ8 × 7L φ10 × 8L φ10 × 10Lφ10 × 12.7L Type φD 5.0 6.3 8.0 10.0 10.0 10.0 L 5.9 5.9 6.9 7.9 9.9 12.6 Voltage A 6.0 7.3 9.0 11.0 11.0 11.0 V 2.5 4 6.3 10 16 B 5.3 6.6 8.3 10.3 10.3 10.3 Code e g j A C C 5.3 6.6 8.3 10.3 10.3 10.3 E 1.6 2.1 3.2 4.6 4.6 4.6 Frequency coefficient of rated ripple current H 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0 Frequency0/ 120Hz 1kHz 10kHz 100kHz or more Coefficient 0.05 0.30 0.70 1.00 Dimension table in next page. 45 CAT.8100H

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS PCG Dimensions Rated Voltage Surge Voltage Rated Capacitance Case Size Leakage Current ESR (mΩ) Rated Ripple tan δ Part Number (V)(code) (V) (µF) φD × L (mm) (µA) (at 100kHz 20°C) (mArms) 220 5 × 6 0.12 110 30 2100 PCG0E221MCL1GS 330 5 × 6 0.12 500 30 2200 PCG0E331MCL1GS 330 5 × 6 0.12 500 10 3300 PCG0E331MCO1GS 470 6.3 × 6 0.12 235 20 2900 PCG0E471MCL1GS 2.5 560 6.3 × 6 0.12 280 20 3000 PCG0E561MCL1GS 2.8 (0E) 820 8 × 7 0.12 410 20 3300 PCG0E821MCL1GS 1500 10 × 8 0.12 750 17 4100 PCG0E152MCL1GS 2700 10 × 10 0.12 1350 12 4700 PCG0E272MCL1GS 3300 10 × 12.7 0.12 1650 10 5500 PCG0E332MCL1GS 4700 10 × 12.7 0.12 2350 10 5600 PCG0E472MCL1GS 180 5 × 6 0.12 144 32 1900 PCG0G181MCL1GS 220 5 × 6 0.12 300 32 2000 PCG0G221MCL1GS 220 5 × 6 0.12 300 15 2900 PCG0G221MCO1GS 390 6.3 × 6 0.12 312 22 2700 PCG0G391MCL1GS 4 4.6 680 8 × 7 0.12 544 21 3200 PCG0G681MCL1GS (0G) 1200 10 × 8 0.12 960 17 4000 PCG0G122MCL1GS 2200 10 × 10 0.12 1760 13 4600 PCG0G222MCL1GS 2700 10 × 12.7 0.12 2160 11 5300 PCG0G272MCL1GS 3300 10 × 12.7 0.12 2640 11 5400 PCG0G332MCL1GS 150 5 × 6 0.12 189 33 1800 PCG0J151MCL1GS 180 5 × 6 0.12 500 33 1900 PCG0J181MCL1GS 180 5 × 6 0.12 500 17 3000 PCG0J181MCO1GS 270 6.3 × 6 0.12 340 23 2600 PCG0J271MCL1GS 6.3 330 6.3 × 6 0.12 416 23 2700 PCG0J331MCL1GS 7.2 (0J) 470 8 × 7 0.12 592 22 3100 PCG0J471MCL1GS 1000 10 × 8 0.12 1260 18 3800 PCG0J102MCL1GS 1800 10 × 10 0.12 2268 14 4400 PCG0J182MCL1GS 2200 10 × 12.7 0.12 2772 12 5000 PCG0J222MCL1GS 2700 10 × 12.7 0.12 3402 12 5100 PCG0J272MCL1GS 82 5 × 6 0.12 164 35 1700 PCG1A820MCL1GS 100 5 × 6 0.12 250 35 1800 PCG1A101MCL1GS 150 6.3 × 6 0.12 300 25 2500 PCG1A151MCL1GS 180 6.3 × 6 0.12 360 25 2600 PCG1A181MCL1GS 10 11.5 330 8 × 7 0.12 660 23 3100 PCG1A331MCL1GS (1A) 560 10 × 8 0.12 1120 20 3600 PCG1A561MCL1GS 820 10 × 10 0.12 1640 15 4300 PCG1A821MCL1GS 1000 10 × 12.7 0.12 2000 13 4800 PCG1A102MCL1GS 1500 10 × 12.7 0.12 3000 13 4900 PCG1A152MCL1GS 47 5 × 6 0.12 150 40 1500 PCG1C470MCL1GS 56 5 × 6 0.12 240 40 1600 PCG1C560MCL1GS 82 6.3 × 6 0.12 262 30 2300 PCG1C820MCL1GS 100 6.3 × 6 0.12 320 30 2400 PCG1C101MCL1GS 16 18.4 150 8 × 7 0.12 480 28 2800 PCG1C151MCL1GS (1C) 270 10 × 8 0.12 864 25 3300 PCG1C271MCL1GS 470 10 × 10 0.12 1504 20 3700 PCG1C471MCL1GS 680 10 × 12.7 0.12 2176 18 4100 PCG1C681MCL1GS 820 10 × 12.7 0.12 2624 18 4200 PCG1C821MCL1GS Rated ripple current (mArms) at 105°C 100kHz Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. 46 CAT.8100H Please refer to page 3 for the minimum order quantity.

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: N ichicon: PCG0E821MCL1GS PCG0E152MCL1GS PCG0E221MCL1GS PCG0E272MCL1GS PCG0E332MCL1GS PCG0E561MCL1GS PCG0G122MCL1GS PCG0G181MCL1GS PCG0G222MCL1GS PCG0G272MCL1GS PCG0G391MCL1GS PCG0G681MCL1GS PCG0J102MCL1GS PCG0E471MCL1GS PCG0J222MCL1GS PCG0J151MCL1GS PCG1A821MCL1GS PCG0J271MCL1GS PCG0J331MCL1GS PCG0J471MCL1GS PCG1A102MCL1GS PCG1A151MCL1GS PCG1A331MCL1GS PCG1A820MCL1GS PCG0J182MCL1GS PCG1C151MCL1GS PCG1C271MCL1GS PCG1C470MCL1GS PCG1C471MCL1GS PCG1C681MCL1GS PCG1C820MCL1GS PCG1A561MCL1GS PCG0J272MCL1GS PCG0E331MCL1GS PCG0E331MCO1GS PCG0E472MCL1GS PCG0G221MCL1GS PCG0G221MCO1GS PCG0G332MCL1GS PCG0J181MCL1GS PCG0J181MCO1GS PCG1A101MCL1GS PCG1A152MCL1GS PCG1A181MCL1GS PCG1C101MCL1GS PCG1C560MCL1GS PCG1C821MCL1GS