NMH Series www.murata-ps.com Isolated 2W Dual Output DC/DC Converters SELECTION GUIDE Nominal Output Output Input ncy Isolation e Order Code VIonltpaugte Voltage Current RCautrerde nLto aatd Efficie Capacitance MTTF1 ackagStyle P V V mA mA % pF kHrs NMH0505DC 5 ±5 ±200 500 80 24 1574 FEATURES NMH0509DC 5 ±9 ±111 494 81 28 663 DIP (cid:132)(cid:3)Efficiency up to 86% NMH0512DC 5 ±12 ±83 488 82 30 338 NMH0515DC 5 ±15 ±67 476 84 33 187 (cid:132)(cid:3)Wide temperature performance at full NMH0505SC 5 ±5 ±200 500 80 24 1574 2 watt load, –40°C to 85°C NMH0509SC 5 ±9 ±111 494 81 28 663 SIP (cid:132)(cid:3)Dual output from a single input rail NMH0512SC 5 ±12 ±83 488 82 30 338 NMH0515SC 5 ±15 ±67 476 84 33 187 (cid:132)(cid:3)Industry standard pinout NMH1205DC 12 ±5 ±200 208 80 35 490 (cid:132)(cid:3)Power sharing on output NMH1209DC 12 ±9 ±111 201 83 55 343 DIP NMH1212DC 12 ±12 ±83 198 84 63 229 (cid:132)(cid:3)1kVDC isolation ‘Hi Pot Test’ NMH1215DC 12 ±15 ±67 198 84 66 148 (cid:132)(cid:3)5V, 12V, 24V & 48V input NMH1205SC 12 ±5 ±200 208 80 35 490 NMH1209SC 12 ±9 ±111 201 83 55 343 (cid:132)(cid:3)5V, 9V, 12V and 15V output SIP NMH1212SC 12 ±12 ±83 198 84 63 229 (cid:132)(cid:3)Internal SMD construction NMH1215SC 12 ±15 ±67 198 84 66 148 (cid:132)(cid:3)No external components required NMH2405DC 24 ±5 ±200 103 81 41 318 NMH2409DC 24 ±9 ±111 98 85 75 249 (cid:132)(cid:3)MTTF up to 1.5 million hours DIP NMH2412DC 24 ±12 ±83 97 86 95 183 (cid:132)(cid:3)No electrolytic or tantalum capacitors NMH2415DC 24 ±15 ±67 97 86 104 127 NMH2405SC 24 ±5 ±200 103 81 41 318 (cid:132)(cid:3)Pin compatible with MEA1 series NMH2409SC 24 ±9 ±111 98 85 75 249 SIP NMH2412SC 24 ±12 ±83 97 86 95 183 DESCRIPTION NMH2415SC 24 ±15 ±67 97 86 104 127 The NMH series of industrial temperature range Recommended DC/DC converters are the standard buliding blocks Alternative for on-board point-of-use power systems. They NMH4805DC 48 ±5 ±200 51 82 45 235 are ideally suited for providing dual rail supplies ep NMH4809DC 48 ±9 ±111 51 82 74 195 R on single rail boards with the added benefit of DIP es NMH4812DC 48 ±12 ±83 49 85 90 152 al galvanic isolation to reduce circuit noise. All of S NMH4815DC 48 ±15 ±67 49 85 112 112 al the rated power may be drawn from a single pin oc provided the total load does not exceed 2 watts. NMH4805SC 48 ±5 ±200 51 82 45 235 ur L NMH4809SC 48 ±9 ±111 51 82 74 195 Yo Pin compatibility with the NMA 1 watt series NMH4812SC 48 ±12 ±83 49 85 90 152 SIP ntact ensures minimal effort in upgrading distributed o NMH4815SC 48 ±15 ±67 49 85 112 112 C power systems. INPUT CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Continuous operation, 5V input types 4.5 5 5.5 Continuous operation, 12V input types 10.8 12 13.2 Voltage range V Continuous operation, 24V input types 21.6 24 26.4 Continuous operation, 48V input types 43.2 48 52.8 5V input types 50 12V input types 70 Reflected ripple current mA p-p 24V input types 130 48V input types 200 1. Calculated using MIL-HDBK-217F with nominal input voltage at full load. For full details go to www.murata-ps.com/rohs All specifications typical at TA=25°C, nominal input voltage and rated output current unless otherwise specified. www.murata-ps.com/support KDC_NMH.F02 Page 1 of 6

NMH Series Isolated 2W Dual Output DC/DC Converters OUTPUT CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Rated Power TA=-40°C to 85°C, see derating graph 2 W Voltage Set Point Accuracy NMH0505DC/SC -5 7.5 % All other types -5 5 Line regulation High VIN to low VIN 1.0 1.2 %/% 10% load to rated load, 5V output types 5 10 10% load to rated load, 9V output types Load Regulation % 10% load to rated load, 12V output types 3 10 10% load to rated load, 15V output types BW=DC to 20MHz, 5V output types 150 200 BW=DC to 20MHz, 9V output types 100 150 Ripple and Noise mV p-p BW=DC to 20MHz, 12V output types 80 150 BW=DC to 20MHz, 15V output types 70 150 ABSOLUTE MAXIMUM RATINGS Lead temperature 1.5mm from case for 10 seconds 260°C Input voltage VIN, NMH05 types 7V Input voltage VIN, NMH12 types 15V Input voltage VIN, NMH24 types 28V Input voltage VIN, NMH48 types 54V ISOLATION CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Isolation test voltage Flash tested for 1 second 1000 VDC Resistance Viso= 500V 1 10 GΩ GENERAL CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units 5V input types 95 Switching frequency 12V input types 90 kHz 24V & 48V input types 80 TEMPERATURE CHARACTERISTICS Parameter Conditions Min. Typ. Max. Units Specification All output types -40 85 Storage -50 130 °C 5V output types 30 Case Temperature above ambient 12V output types 25 Cooling Free air convection TEMPERATURE DERATING GRAPH TOLERANCE ENVELOPE +10% 3 +5% Typical Load Line +2.5% e V ut Power (W) 12 Safe Operating Are8a5°C Output Voltag NOM --27..55%% p ut O 10 25 50 75 100 0 Output Load Current (%) -40 0 50 100 150 Ambient Temperature (°C) The voltage tolerance envelope shows typical load regulation characteristics for this product series. The tolerance envelope is the maximum output voltage variation due to changes in output loading. www.murata-ps.com/support KDC_NMH.F02 Page 2 of 6

NMH Series Isolated 2W Dual Output DC/DC Converters TECHNICAL NOTES ISOLATION VOLTAGE ‘Hi Pot Test’, ‘Flash Tested’, ‘Withstand Voltage’, ‘Proof Voltage’, ‘Dielectric Withstand Voltage’ & ‘Isolation Test Voltage’ are all terms that relate to the same thing, a test voltage, applied for a specified time, across a component designed to provide electrical isolation, to verify the integrity of that isolation. Murata Power Solutions NMH series of DC/DC converters are all 100% production tested at their stated isolation voltage. This is 1kVDC for 1 second. A question commonly asked is, “What is the continuous voltage that can be applied across the part in normal operation?” For a part holding no specific agency approvals, such as the NMH series, both input and output should normally be maintained within SELV limits i.e. less than 42.4V peak, or 60VDC. The isolation test voltage represents a measure of immunity to transient voltages and the part should never be used as an element of a safety isolation system. The part could be expected to function correctly with several hundred volts offset applied continuously across the isolation barrier; but then the circuitry on both sides of the barrier must be regarded as operating at an unsafe voltage and further isolation/insulation systems must form a barrier between these circuits and any user-accessible circuitry according to safety standard requirements. REPEATED HIGH-VOLTAGE ISOLATION TESTING It is well known that repeated high-voltage isolation testing of a barrier component can actually degrade isolation capability, to a lesser or greater degree depending on materials, construction and environment. The NMH series has toroidal isolation transformers, with no additional insulation between primary and secondary windings of enameled wire. While parts can be expected to withstand several times the stated test voltage, the isolation capability does depend on the wire insulation. Any material, including this enamel (typically polyurethane) is susceptible to eventual chemical degradation when subject to very high applied voltages thus implying that the number of tests should be strictly limited. We therefore strongly advise against repeated high voltage isolation testing, but if it is absolutely required, that the voltage be reduced by 20% from specified test voltage. This consideration equally applies to agency recognised parts rated for better than functional isolation where the wire enamel insulation is always supplemented by a further insulation system of physical spacing or barriers. RoHS COMPLIANCE INFORMATION This series is compatible with RoHS soldering systems with a peak wave solder temperature of 260°C for 10 seconds. The pin termination finish on the SIP package type is Tin Plate, Hot Dipped over Matte Tin with Nickel Preplate. The DIP types are Matte Tin over Nickel Preplate. Both types in this series are backward compatible with Sn/Pb soldering systems. For further information, please visit www.murata-ps.com/rohs APPLICATION NOTES Minimum load The minimum load to meet datasheet specification is 10% of the full rated load across the specified input voltage range. Lower than 10% minimum loading will result in an increase in output voltage, which may rise to typically double the specified output voltage if the output load falls to less than 5%. Capacitive loading and start up Typical start up times for this series, with a typical input voltage rise time of 2.2μs and output capacitance of 10μF, are shown in the table below. The product series will start into a capacitance of 47μF with an increased start time, however, the maximum recommended output capacitance is 10μF. Typical Start-Up Wave Form Start-up time Start-up time μs μs NMH0505SC 1072 NMH2405SC 1064 NMH0509SC 2481 NMH2409SC 1544 NMH0512SC 3546 NMH2412SC 4398 NMH0515SC 5380 NMH2415SC 4230 NMH1205SC 672 NMH4805SC 966 NMH1209SC 1152 NMH4809SC 1220 NMH1212SC 1580 NMH4812SC 2822 NMH1215SC 3150 NMH4815SC 4275 www.murata-ps.com/support KDC_NMH.F02 Page 3 of 6

NMH Series Isolated 2W Dual Output DC/DC Converters APPLICATION NOTES (continued) Ripple & Noise Characterisation Method Ripple and noise measurements are performed with the following test configuration. C1 1μF X7R m ultilayer ceramic capacitor, voltage rating to be a minimum of 3 times the output voltage of the DC/DC converter 10μF tantalum capacitor, voltage rating to be a minimum of 1.5 times the output voltage of the DC/DC converter with an ESR of less C2 than 100mΩ at 100 kHz C3 100nF multilayer ceramic capacitor, general purpose R1 450Ω resistor, carbon film, ±1% tolerance R2 50Ω BNC termination T1 3T of the coax cable through a ferrite toroid RLOAD Resistive load to the maximum power rating of the DC/DC converter. Connections should be made via twisted wires Measured values are multiplied by 10 to obtain the specified values. Differential Mode Noise Test Schematic DC/DC Converter OSCILLOSCOPE C1 C2 C3 R1 T1 R2 + + Y INPUT SUPPLY Input Output - - R LOAD OUTPUT RIPPLE REDUCTION By using the values of inductance and capacitance stated, the output ripple at the rated load is lowered to 5mV p-p max. Component selection Capacitor: Ceramic chip capacitors are recommended. It is required that the ESR (Equivalent Series Resistance) should be as low as possible, X7R types are recommended. The voltage rating should be at least twice (except for 15V output), the rated output voltage of the DC/DC converter. Inductor: The rated current of the inductor should not be less than that of the output of the DC/DC converter. At the rated current, the DC resistance of the inductor should be such that the voltage drop across the inductor is <2% of the rated voltage of the DC/DC converter. The SRF (Self Resonant Frequency) should be >20MHz. L DC Power C Load Source DC Inductor Order Codes Order Code L (μH) C (μF) SMD Through Hole NMH0505XC 47 82473C 11R473C 4.7 NMH0509XC 47 82473C 11R473C 2.2 NMH0512XC 150 82154C 11R154C 3.3 Product specification for MPS inductors can be found at: NMH0515XC 100 82104C 11R104C 3.3 NMH1205XC 47 82473C 11R473C 4.7 1100R Series (Through Hole) http://www.murata-ps.com/data/magnetics/kmp_1100r.pdf NMH1209XC 47 82473C 11R473C 2.2 NMH1212XC 150 82154C 11R154C 3.3 8200 Series (SMD) NMH1215XC 100 82104C 11R104C 3.3 http://www.murata-ps.com/data/magnetics/kmp_8200c.pdf NMH2405XC 47 82473C 11R473C 4.7 NMH2409XC 47 82473C 11R473C 2.2 NMH2412XC 150 82154C 11R154C 3.3 NMH2415XC 100 82104C 11R104C 3.3 NMH4805XC 47 82473C 11R473C 4.7 NMH4809XC 47 82473C 11R473C 2.2 NMH4812XC 150 82154C 11R154C 3.3 NMH4815XC 100 82104C 11R104C 3.3 www.murata-ps.com/support KDC_NMH.F02 Page 4 of 6

NMH Series Isolated 2W Dual Output DC/DC Converters PACKAGE SPECIFICATIONS MECHANICAL DIMENSIONS PIN CONNECTIONS - 14 PIN DIP DIP package SIP package Pin Function 19.50 [0.77] 19.50 [0.77] 1 -VIN 7 NC 7.50 [0.295] 9.80 [0.386] NMH0505DC 8 OV XYYWW 9 +VOUT 11 -VOUT 7.70 [0.303] 10.00 [0.40] NMXHY0Y5W0W5SC 0.40 [0.016] MIN PIN C1O4NNECTIONS +- V7IN PIN SIP 4.10±0.50 [0.161±0.020] 4.10±0.50 [0.161±0.020] 1 2 4 5 6 Pin Function 0.50±0.05 [022.0..302780± [000.0..00098232]] 7.62 [0.300] 0.50±0.05 [0.020±0.002] 2.54 [0.100] 12 +-VVIINN 11..4004 [00..005451] 1 7 45 -VOOVUT 14 11 9 8 11..4050 [00..005379] 12.70 [0.500] 6 +VOUT 0.25±0.05 [0.010±0.002] 15.24 [0.600] 7.62 [0.300] 12..5542 [00..009691] 0.25±0.05 [0.010±0.002] Unless otherwise stated all dimensions in mm (inches) ±0.25mm (0.010”). Controlling dimension is mm. All pins on a 2.54mm (0.100”) pitch and within 0.25mm (0.010”) of true position. Weight: 2.85g (DIP) 2.76g (SIP) www.murata-ps.com/support KDC_NMH.F02 Page 5 of 6

NMH Series Isolated 2W Dual Output DC/DC Converters PACKAGE SPECIFICATIONS (continued) RECOMMENDED FOOTPRINT DETAILS 14 Pin DIP Package 7 Pin SIP Package x6 HOLES x5 HOLES Ø1.00 [Ø0.039] Ø1.00 [Ø0.039] 2.54 [0.100] 2.54 [0.100] 2.54 [0.100] 2.54 [0.100] TUBE OUTLINE DIMENSIONS 14 Pin DIP Tube 7 Pin SIP Tube 12.0 [0.472] 9.3 [0.366] 12.43 [0.489] 14.5 [0.571] 18.0 [0.709] 5.07±0.80 [0.200±0.03] 5.05 [0.199] 5.0 [0.197] Unless otherwise specified all dimensions in mm [inches] ±0.55mm [0.022].Tube length (14 Pin DIP) : 520mm [20.472] ±2.0 [0.079]. Tube length (7 Pin SIP) : 520mm [20.472] ±2.0 [0.079]. Tube Quantity : 25 This product is subject to the following operating requirements Murata Power Solutions, Inc. and the Life and Safety Critical Application Sales Policy: 11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A. Refer to: http://www.murata-ps.com/requirements/ ISO 9001 and 14001 REGISTERED Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without notice. © 2017 Murata Power Solutions, Inc. www.murata-ps.com/support KDC_NMH.F02 Page 6 of 6

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: M urata: NMH0512SC NMH2405SC NMH1209SC NMH0515SC NMH0515DC NMH1209DC NMH1205DC NMH1205SC NMH2409SC NMH2409DC NMH0509DC NMH0509SC NMH1215SC NMH0505DC NMH0505SC NMH1215DC NMH0512DC NMH1212SC NMH1212DC NMH2405DC NMH2412SC NMH2412DC NMH2415SC NMH2415DC