I N D U C T O R S September 2017 Inductors for Standard Circuits Wound Ferrite NLV-PF Series NLV32-PF Type NLV32-PF 3225 [1210 inch]* * Dimensions Code JIS[EIA] Caution The products in this catalog is not recommended to a new design Please refer to our Web site about replacement information.

The products in this catalog is not recommended to a new design (2/10) I N D U C T O R S REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The storage period is less than 6 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150°C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/Aviation equipment (8) Public information-processing equipment (2) Transportation equipment (cars, electric trains, ships, etc.) (9) Military equipment (3) Medical equipment (10) Electric heating apparatus, burning equipment (4) Power-generation control equipment (11) Disaster prevention/crime prevention equipment (5) Atomic energy-related equipment (12) Safety equipment (6) Seabed equipment (13) Other applications that are not considered general-purpose (7) Transportation control equipment applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. 20170920 / inductor_commercial_standard_nlv32-pf_en.fm

The products in this catalog is not recommended to a new design (3/10) I N D U C T O R S Inductors for Standard Circuits Product compatible with RoHS directive Halogen-free Wound Ferrite Compatible with lead-free solders Overview of NLV32-PF Type FEATURES Resin mold type wound inductor for standard circuits. E-12 Series, wide lineup compatible with J (±5%) tolerance, can be used for applications that need to meet strict L tolerance such as filter circuits. Has excellent inductance temperature characteristics in the operating temperature range. APPLICATION Smart meters, AV equipment, xDSL, electronic devices for communications infrastructure such as mobile base stations, industrial equipment, other PART NUMBER CONSTRUCTION NLV 32 T - 010 - J - PF L×W×H Dimensions Inductance Inductance Series name Packaging style Internal code (mm) (µH) tolerance 32 3.2×2.5×2.2 T Taping 010 0.01 J ±5% Compatible with the RoHS R10 0.1 PF Directive, Exemption 1R0 1 regulations apply 100 10 101 100 OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Temperature range Package quantity Individual weight Type Operating Storage temperature temperature （°C） （°C） (pieces/reel) （mg） NLV32-PF –40 to +105 –40 to +105 2000 50 Operating temperature range includes self-temperature rise. The Storage temperature range is for after the circuit board is mounted. RoHS Directive Compliant Product: See the following for more details.https://product.tdk.com/info/en/environment/rohs/index.html Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20170920 / inductor_commercial_standard_nlv32-pf_en.fm

The products in this catalog is not recommended to a new design (4/10) I N D U C T O R S NLV32-PF Type RECOMMENDED REFLOW PROFILE Preheating Soldering Natural cooling Peak T4 e ur T3 T3 at er p m e T T2 T: t3 T1 t1 t2 t: Time Preheating Soldering Peak Temp. Time Temp. Time Temp. Time T1 T2 t1 T3 t2 T4 t3 150°C 180°C 90 to 120s 230°C 40s 255°C 10s max. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20170920 / inductor_commercial_standard_nlv32-pf_en.fm

The products in this catalog is not recommended to a new design (5/10) I N D U C T O R S NLV32-PF Type SHAPE & DIMENSIONS 470J 2 1 0. 0. ± ± 5 9 2. 1. 3.2±0.2 0.55 (0.55) (2.1) (0.55) 2 0. ± 2 2. Dimensions in mm RECOMMENDED LAND PATTERN 2 1.2 2 1.2 Dimensions in mm Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20170920 / inductor_commercial_standard_nlv32-pf_en.fm

The products in this catalog is not recommended to a new design (6/10) I N D U C T O R S NLV32-PF Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE L Q L, Q measuring Self-resonant DC resistance Rated current Part No. frequency frequency (µH) Tolerance min. (MHz) (MHz)min. (Ω)max. (mA)max. 0.01 ±5% 15 100 2500 0.13 450 NLV32T-010J-PF 0.012 ±5% 17 100 2300 0.14 450 NLV32T-012J-PF 0.015 ±5% 19 100 2100 0.16 450 NLV32T-015J-PF 0.018 ±5% 21 100 1900 0.18 450 NLV32T-018J-PF 0.022 ±5% 23 100 1700 0.2 450 NLV32T-022J-PF 0.027 ±5% 23 100 1500 0.22 450 NLV32T-027J-PF 0.033 ±5% 25 100 1400 0.24 450 NLV32T-033J-PF 0.039 ±5% 25 100 1300 0.27 450 NLV32T-039J-PF 0.047 ±5% 26 100 1200 0.3 450 NLV32T-047J-PF 0.056 ±5% 26 100 1100 0.33 450 NLV32T-056J-PF 0.068 ±5% 27 100 1000 0.36 450 NLV32T-068J-PF 0.082 ±5% 27 100 900 0.4 450 NLV32T-082J-PF 0.1 ±5% 28 100 700 0.44 450 NLV32T-R10J-PF 0.12 ±5% 30 25.2 500 0.22 450 NLV32T-R12J-PF 0.15 ±5% 30 25.2 450 0.25 450 NLV32T-R15J-PF 0.18 ±5% 30 25.2 400 0.28 450 NLV32T-R18J-PF 0.22 ±5% 30 25.2 350 0.32 450 NLV32T-R22J-PF 0.27 ±5% 30 25.2 320 0.36 450 NLV32T-R27J-PF 0.33 ±5% 30 25.2 300 0.4 450 NLV32T-R33J-PF 0.39 ±5% 30 25.2 250 0.45 450 NLV32T-R39J-PF 0.47 ±5% 30 25.2 220 0.5 450 NLV32T-R47J-PF 0.56 ±5% 30 25.2 180 0.55 450 NLV32T-R56J-PF 0.68 ±5% 30 25.2 160 0.6 450 NLV32T-R68J-PF 0.82 ±5% 30 25.2 140 0.65 450 NLV32T-R82J-PF 1 ±5% 30 7.96 120 0.7 400 NLV32T-1R0J-PF 1.2 ±5% 30 7.96 100 0.75 390 NLV32T-1R2J-PF 1.5 ±5% 30 7.96 85 0.85 370 NLV32T-1R5J-PF 1.8 ±5% 30 7.96 80 0.9 350 NLV32T-1R8J-PF 2.2 ±5% 30 7.96 75 1 320 NLV32T-2R2J-PF 2.7 ±5% 30 7.96 70 1.1 290 NLV32T-2R7J-PF 3.3 ±5% 30 7.96 60 1.2 260 NLV32T-3R3J-PF 3.9 ±5% 30 7.96 55 1.3 250 NLV32T-3R9J-PF 4.7 ±5% 30 7.96 50 1.5 220 NLV32T-4R7J-PF 5.6 ±5% 30 7.96 45 1.6 200 NLV32T-5R6J-PF 6.8 ±5% 30 7.96 40 1.8 180 NLV32T-6R8J-PF 8.2 ±5% 30 7.96 35 2 170 NLV32T-8R2J-PF Rated current: smaller value of either Idc1 or Idc2. Idc1: When based on the inductance change rate (10% below the initial L value) Idc2: When based on the temperature increase (Temperature increase of 20°C by self heating) ○Measurement equipment Measurement item Product No. Manufacturer 4191A+16092A L, Q Keysight Technologies 4194A+16085A+16093B Self-resonant frequency 8753C Keysight Technologies DC resistance VP-2941A Panasonic ＊ Equivalent measurement equipment may be used. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20170920 / inductor_commercial_standard_nlv32-pf_en.fm

The products in this catalog is not recommended to a new design (7/10) I N D U C T O R S NLV32-PF Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE L Q L, Q measuring Self-resonant DC resistance Rated current Part No. frequency frequency (µH) Tolerance min. (MHz) (MHz)min. (Ω)max. (mA)max. 10 ±5% 30 2.52 30 2.1 150 NLV32T-100J-PF 12 ±5% 30 2.52 20 2.5 140 NLV32T-120J-PF 15 ±5% 30 2.52 20 2.8 130 NLV32T-150J-PF 18 ±5% 30 2.52 20 3.3 120 NLV32T-180J-PF 22 ±5% 30 2.52 20 3.7 110 NLV32T-220J-PF 27 ±5% 30 2.52 20 5 80 NLV32T-270J-PF 33 ±5% 30 2.52 17 5.6 70 NLV32T-330J-PF 39 ±5% 30 2.52 16 6.4 65 NLV32T-390J-PF 47 ±5% 30 2.52 15 7 60 NLV32T-470J-PF 56 ±5% 30 2.52 13 8 55 NLV32T-560J-PF 68 ±5% 30 2.52 12 9 50 NLV32T-680J-PF 82 ±5% 30 2.52 11 10 45 NLV32T-820J-PF 100 ±5% 20 0.796 10 10 40 NLV32T-101J-PF 120 ±5% 20 0.796 10 11 70 NLV32T-121J-PF 150 ±5% 20 0.796 8 15 65 NLV32T-151J-PF 180 ±5% 20 0.796 7 17 60 NLV32T-181J-PF 220 ±5% 20 0.796 7 21 50 NLV32T-221J-PF 270 ±5% 20 0.796 6 28 45 NLV32T-271J-PF 330 ±5% 20 0.796 5 34 40 NLV32T-331J-PF 390 ±5% 20 0.796 5 36 35 NLV32T-391J-PF 470 ±5% 20 0.796 4 40 25 NLV32T-471J-PF Rated current: smaller value of either Idc1 or Idc2. Idc1: When based on the inductance change rate (10% below the initial L value) Idc2: When based on the temperature increase (Temperature increase of 20°C by self heating) ○Measurement equipment Measurement item Product No. Manufacturer 4191A+16092A L, Q Keysight Technologies 4194A+16085A+16093B Self-resonant frequency 8753C Keysight Technologies DC resistance VP-2941A Panasonic ＊ Equivalent measurement equipment may be used. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20170920 / inductor_commercial_standard_nlv32-pf_en.fm

The products in this catalog is not recommended to a new design (8/10) I N D U C T O R S NLV32-PF Type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH 10000 221J 471J 391J 331J 271J 1000 181J151J 101J 820J 121J 100J 8R2J 6R8J5R6J 4R7J 3R9J 3R3J 2R7J 100 2R2J 1R8J 680J 560J 470J 390J 330J 270J 220J 10 180J )H 150J R82J µ R68J (e 120J R56J c n ucta 1R5J 1R2J R47J d R39J n R33J I 1 1R0J R27J082J R22J R10J 0.1 0.01 033J 027J 022J 018J 015J 010J 012J 047J 056J 068J R12J R15J R18J 039J 0.001 0.1 1 10 100 1000 Frequency(MHz) ○Measurement equipment Product No. Manufacturer 4291A Keysight Technologies 4294A Keysight Technologies ＊ Equivalent measurement equipment may be used. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20170920 / inductor_commercial_standard_nlv32-pf_en.fm

The products in this catalog is not recommended to a new design (9/10) I N D U C T O R S NLV32-PF Type ELECTRICAL CHARACTERISTICS Q FREQUENCY CHARACTERISTICS GRAPH 70 056J 068J 60 039J 047J 082J 50 033J 180J 100J 1R2J 220J 6R8J 4R7J 1R0J 027J 8R2J 40 270J 1R5J 010J Q 391J 12802J0J 12RR87JJ R10J 012J 5R6J 2R2J R82J R56J 30 150J 271J R39J 015J 330J 221J 121J R15J 390J R12J 3R3J 018J 3R9J 470J 022J 560J 20 R47J R68J 680J R18J 331J R22J 10 R27J 101J R33J 151J 181J 471J 0 0.1 1 10 100 1000 Frequency(MHz) ○Measurement equipment Product No. Manufacturer 4291A Keysight Technologies 4294A Keysight Technologies ＊ Equivalent measurement equipment may be used. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20170920 / inductor_commercial_standard_nlv32-pf_en.fm

The products in this catalog is not recommended to a new design (10/10) I N D U C T O R S NLV32-PF Type PACKAGING STYLE REEL DIMENSIONS 2.0±0.5 E Type A W1 W2 N E NLV32-PF ø180 9 13 ø60 0.5 * These values are typical values. N (1.0) ø13.0±0.5 W1 ø21.0±0.8 W2 A Dimensions in mm TAPE DIMENSIONS øD0 P2 P0 P1 K E F W B A t Dimensions in mm Type A B øD0 E F P0 P1 P2 W K t NLV32-PF 2.8 3.5 1.5+0.1/-0 1.75±0.1 3.50±0.05 4.00±0.10 4.00±0.10 2.00±0.05 8.00±0.30 2.3 0.4 Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20170920 / inductor_commercial_standard_nlv32-pf_en.fm