I N D U C T O R S September 2017 Inductors for Decoupling Circuits Wound Ferrite NLFV-PF Series NLFV25-PF Type NLFV25-PF 2520 [1008 inch]* * Dimensions Code JIS[EIA] Caution The products in this catalog is not recommended to a new design Please refer to our Web site about replacement information.

The products in this catalog is not recommended to a new design (2/10) I N D U C T O R S REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The storage period is less than 6 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150°C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/Aviation equipment (8) Public information-processing equipment (2) Transportation equipment (cars, electric trains, ships, etc.) (9) Military equipment (3) Medical equipment (10) Electric heating apparatus, burning equipment (4) Power-generation control equipment (11) Disaster prevention/crime prevention equipment (5) Atomic energy-related equipment (12) Safety equipment (6) Seabed equipment (13) Other applications that are not considered general-purpose (7) Transportation control equipment applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. 20170920 / inductor_commercial_decoupling_nlfv25-pf_en.fm

The products in this catalog is not recommended to a new design (3/10) I N D U C T O R S Inductors for Decoupling Circuits Product compatible with RoHS directive Halogen-free Wound Ferrite Compatible with lead-free solders Overview of NLFV25-PF Type FEATURES Resin mold type wound inductor for decoupling circuits. Magnetic shield type containing ferrite powder in the exterior mold resin. APPLICATION Smart meters, AV equipment, xDSL, electronic devices for communications infrastructure such as mobile base stations, industrial equipment, other PART NUMBER CONSTRUCTION NLFV 25 T - 1R0 M - PF L×W×H Dimensions Inductance Inductance Series name Packaging style Internal code (mm) (µH) tolerance 25 2.5×2.0×1.8 T Taping 1R0 1 K ±10% Compatible with the RoHS 100 10 M ±20% PF Directive, Exemption 101 100 regulations apply OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Temperature range Package quantity Individual weight Type Operating Storage temperature temperature （°C） （°C） (pieces/reel) （mg） NLFV25-PF –40 to +105 –40 to +105 2000 25 Operating temperature range includes self-temperature rise. The Storage temperature range is for after the circuit board is mounted. RoHS Directive Compliant Product: See the following for more details.https://product.tdk.com/info/en/environment/rohs/index.html Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20170920 / inductor_commercial_decoupling_nlfv25-pf_en.fm

The products in this catalog is not recommended to a new design (4/10) I N D U C T O R S NLFV25-PF Type RECOMMENDED REFLOW PROFILE Preheating Soldering Natural cooling Peak T4 e ur T3 T3 at er p m e T T2 T: t3 T1 t1 t2 t: Time Preheating Soldering Peak Temp. Time Temp. Time Temp. Time T1 T2 t1 T3 t2 T4 t3 150°C 180°C 90 to 120s 230°C 40s 255°C 10s max. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20170920 / inductor_commercial_decoupling_nlfv25-pf_en.fm

The products in this catalog is not recommended to a new design (5/10) I N D U C T O R S NLFV25-PF Type SHAPE & DIMENSIONS 2±0.1 1.4±0.1 2.5±0.2 0.5 (0.4) (1.7) (0.4) 1 0. ± 8 1. Dimensions in mm RECOMMENDED LAND PATTERN 5 1. 1.0 1.5 1.0 Dimensions in mm Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20170920 / inductor_commercial_decoupling_nlfv25-pf_en.fm

The products in this catalog is not recommended to a new design (6/10) I N D U C T O R S NLFV25-PF Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE L L measuring DC resistance Rated current Part No. frequency (µH) Tolerance (MHz) (Ω)±20% (mA)max. 1 ±20% 7.96 0.07 455 NLFV25T-1R0M-PF 1.5 ±20% 7.96 0.09 350 NLFV25T-1R5M-PF 2.2 ±20% 7.96 0.1 315 NLFV25T-2R2M-PF 3.3 ±20% 7.96 0.2 280 NLFV25T-3R3M-PF 4.7 ±20% 7.96 0.24 210 NLFV25T-4R7M-PF 6.8 ±20% 7.96 0.29 175 NLFV25T-6R8M-PF 10 ±10% 2.52 0.36 155 NLFV25T-100K-PF 15 ±10% 2.52 0.75 130 NLFV25T-150K-PF 22 ±10% 2.52 1 105 NLFV25T-220K-PF 33 ±10% 2.52 1.4 85 NLFV25T-330K-PF 47 ±10% 2.52 1.7 60 NLFV25T-470K-PF 68 ±10% 2.52 3.3 50 NLFV25T-680K-PF 100 ±10% 0.796 4 40 NLFV25T-101K-PF  Rated current: smaller value of either Idc1 or Idc2. Idc1: When based on the inductance change rate (10% below the initial L value) Idc2: When based on the temperature increase (Temperature increase of 20°C by self-heating) ○Measurement equipment Measurement item Product No. Manufacturer L 4194A+16085A+16093B Keysight Technologies DC resistance VP-2941A Panasonic ＊ Equivalent measurement equipment may be used. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20170920 / inductor_commercial_decoupling_nlfv25-pf_en.fm

The products in this catalog is not recommended to a new design (7/10) I N D U C T O R S NLFV25-PF Type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH 1000 100 101K 680K 470K 330K 220K )H μ 150K (e nc 10 a 100K ct u d 6R8M n I 4R7M 3R3M 2R2M 1R5M 1 1R0M 0.1 0.1 1 10 100 Frequency(MHz) ○Measurement equipment Product No. Manufacturer 4294A Keysight Technologies ＊ Equivalent measurement equipment may be used. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20170920 / inductor_commercial_decoupling_nlfv25-pf_en.fm

The products in this catalog is not recommended to a new design (8/10) I N D U C T O R S NLFV25-PF Type ELECTRICAL CHARACTERISTICS INDUCTANCE VS. DC BIAS CHARACTERISTICS GRAPH 1000 100 101K 680K 470K 330K 220K )H μ 150K (e nc 10 a 100K ct u nd 6R8M I 4R7M 3R3M 2R2M 1R5M 1 1R0M 0.1 0.01 0.1 1 10 DC current(A) ○Measurement equipment Product No. Manufacturer 4285A+42841A+42842C Keysight Technologies ＊ Equivalent measurement equipment may be used. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20170920 / inductor_commercial_decoupling_nlfv25-pf_en.fm

The products in this catalog is not recommended to a new design (9/10) I N D U C T O R S NLFV25-PF Type ELECTRICAL CHARACTERISTICS IMPEDANCE FREQUENCY CHARACTERISTICS GRAPH 100000 101K 680K 470K 330K 220K 10000 150K 100K 6R8M 4R7M 3R3M 2R2M 1R5M 1000 1R0M Ω) (e c n 100 a d e p m I 10 1 0.1 0.1 1 10 100 1000 Frequency(MHz) ○Measurement equipment Product No. Manufacturer 4294A Keysight Technologies ＊ Equivalent measurement equipment may be used. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20170920 / inductor_commercial_decoupling_nlfv25-pf_en.fm

The products in this catalog is not recommended to a new design (10/10) I N D U C T O R S NLFV25-PF Type PACKAGING STYLE REEL DIMENSIONS 2.0±0.5 E Type A W1 W2 N E NLFV25-PF ø180 9 13 ø60 0.5 * These values are typical values. N (1.0) ø13.0±0.5 W1 ø21.0±0.8 W2 A Dimensions in mm TAPE DIMENSIONS øD0 P2 P0 P1 K E F W B A t Dimensions in mm Type A B øD0 E F P0 P1 P2 W K t NLFV25-PF 2.3 2.7 1.5+0.1/-0 1.75±0.1 3.50±0.05 4.00±0.10 4.00±0.10 2.00±0.05 8.00±0.30 2 0.4 Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20170920 / inductor_commercial_decoupling_nlfv25-pf_en.fm

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: T DK: NLFV25T-1R0M-PF NLFV25T-2R2M-PF NLFV25T-220K-PF NLFV25T-101K-PF NLFV25T-1R5M-PF NLFV25T- 150K-PF NLFV25T-680K-PF NLFV25T-330K-PF NLFV25T-6R8M-PF NLFV25T-470K-PF NLFV25T-4R7M-PF NLFV25T-3R3M-PF