MAX803 Series, NCP803 Series Very Low Supply Current 3-Pin Microprocessor Reset Monitor www.onsemi.com The MAX803/NCP803 is a cost−effective system supervisor circuit designed to monitor V in digital systems and provide a reset signal to CC MARKING the host processor when necessary. No external components are DIAGRAM required. The reset output is driven active within 10 (cid:2)sec of V falling 3 CC 3 SOT−23 through the reset voltage threshold. Reset is maintained active for a xxx M(cid:2) (TO−236) timeout period which is trimmed by the factory after V rises above (cid:2) CC 1 CASE 318 the reset threshold. The MAX803/NCP803 has an open drain 1 2 2 active−low RESET output. Both devices are available in SOT−23 and SC−70 packages. SC−70 The MAX803/NCP803 is optimized to reject fast transient glitches xx M(cid:2) (SOT−323) on the V line. Low supply current of 0.5 (cid:2)A (V = 3.2 V) make (cid:2) CC CC CASE 419 these devices suitable for battery powered applications. 1 Features • Precision V Monitor for 1.5 V, 2.5 V, 3.0 V, 3.3 V, and 5.0 V xxx = Specific Device Code CC M = Date Code Supplies (cid:2) = Pb−Free Package • Precision Monitoring Voltages from 1.2 V to 4.9 V Available (Note: Microdot may be in either location) in 100 mV Steps • Four Guaranteed Minimum Power−On Reset Pulse Width Available PIN CONFIGURATION (1 ms, 20 ms, 100 ms, and 140 ms) • RESET Output Guaranteed to V = 1.0 V CC • GND 1 Low Supply Current • V Transient Immunity CC • No External Components 3 VCC • Wide Operating Temperature: −40°C to 105°C • RESET 2 These Devices are Pb−Free and are RoHS Compliant Typical Applications • SOT−23/SC−70 Computers (Top View) • Embedded Systems • Battery Powered Equipment ORDERING INFORMATION • Critical Microprocessor Power Supply Monitoring See detailed ordering and shipping information in the package dimensions section on page 8 of this data sheet. VCC DEVICE MARKING INFORMATION VCC VCC See general marking information in the device marking Rpull−up section on page 8 of this data sheet. MAX803 (cid:2)P NCP803 C = 100 nF RESET RESET GND GND 0 0 Figure 1. Typical Application Diagram © Semiconductor Components Industries, LLC, 2006 1 Publication Order Number: October, 2015 − Rev. 10 MAX803/D

MAX803 Series, NCP803 Series 3 2 VCC Timeout Oscillator Counter RESET Vref 1 GND Figure 2. NCP803, MAX803 Series Open−Drain Active−Low Output PIN DESCRIPTION Pin No. Symbol Description ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ 1 GND Ground ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ÁÁÁ2 ÁÁÁÁRÁESEÁT ÁÁÁRÁESEÁT oÁutpuÁt remÁainsÁ lowÁ whiÁle VCÁC isÁ beloÁw thÁe reÁset vÁoltagÁe thÁreshÁold, Áand Áfor aÁ reseÁt timÁeouÁt period after VCC rises above reset threshold. ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ 3 VCC Supply Voltage: C = 100 nF is recommended as a bypass capacitor between VCC and GND. ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ ABSOLUTE MAXIMUM RATINGS Rating Symbol Value Unit Power Supply Voltage (VCC to GND) VCC −0.3 to 6.0 V RESET Output Voltage (CMOS) −0.3 to (VCC + 0.3) V Input Current, VCC 20 mA Output Current, RESET 20 mA dV/dt (VCC) 100 V/(cid:2)sec Thermal Resistance, Junction−to−Air (Note 1) SOT−23 R(cid:3)JA 301 °C/W SC−70 314 Operating Junction Temperature Range TJ −40 to +125 °C Storage Temperature Range Tstg −65 to +150 °C Lead Temperature (Soldering, 10 Seconds) Tsol +260 °C ESD Protection V Human Body Model (HBM): Following Specification JESD22−A114 2000 Machine Model (MM): Following Specification JESD22−A115 200 Latchup Current Maximum Rating: Following Specification JESD78 Class II ILatchup mA Positive 200 Negative 200 Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. 1. This based on a 35x35x1.6mm FR4 PCB with 10mm2 of 1 oz copper traces under natural convention conditions and a single component characterization. 2. The maximum package power dissipation limit must not be exceeded. PD(cid:2)TJ(mRa(cid:3)xJ)A(cid:3)TA with TJ(max) = 150°C www.onsemi.com 2

MAX803 Series, NCP803 Series ELECTRICAL CHARACTERISTICS TA = −40°C to +105°C unless otherwise noted. Typical values are at TA = +25°C. (Note 3) Characteristic Symbol Min Typ Max Unit VCC Range V TA = 0°C to +70°C 1.0 − 5.5 TA = −40°C to +105°C (Note 4) 1.2 − 5.5 Supply Current ICC (cid:2)A VCC = 3.3 V TA = −40°C to +85°C − 0.5 1.2 TA = 85°C to +105°C (Note 5) − − 2.0 VCC = 5.5 V TA = −40°C to +85°C − 0.8 1.8 TA = 85°C to +105°C (Note 5) − − 2.5 Reset Threshold (Vin Decreasing) (Note 6) VTH V MAX803SQ463/NCP803SN463 TA = +25°C 4.56 4.63 4.70 TA = −40°C to +85°C 4.51 − 4.75 TA = +85°C to +105°C (Note 5) 4.40 − 4.88 MAX803SQ438/NCP803SN438 TA = +25°C 4.31 4.38 4.45 TA = −40°C to +85°C 4.27 4.49 TA = +85°C to +105°C (Note 5) 4.16 4.60 NCP803SN400 TA = +25°C 3.94 4.00 4.06 TA = −40°C to +85°C 3.90 4.10 TA = +85°C to +105°C (Note 5) 3.80 4.20 MAX803SQ308/NCP803SN308 TA = +25°C 3.04 3.08 3.11 TA = −40°C to +85°C 3.00 − 3.15 TA = +85°C to +105°C (Note 5) 2.92 − 3.23 MAX803SQ293/NCP803SN293 TA = +25°C 2.89 2.93 2.96 TA = −40°C to +85°C 2.85 − 3.00 TA = +85°C to +105°C (Note 5) 2.78 − 3.08 NCP803SN263 TA = +25°C 2.59 2.63 2.66 TA = −40°C to +85°C 2.55 − 2.70 TA = +85°C to +105°C (Note 5) 2.50 − 2.76 NCP803SN232 TA = +25°C 2.29 2.32 2.35 TA = −40°C to +85°C 2.26 − 2.38 TA = +85°C to +105°C (Note 5) 2.20 − 2.45 NCP803SN160 TA = +25°C 1.58 1.60 1.62 TA = −40°C to +85°C 1.56 − 1.64 TA = +85°C to +105°C (Note 5) 1.52 − 1.68 MAX803SN120, MAX803SQ120 TA = +25°C 1.18 1.20 1.22 TA = −40°C to +85°C 1.17 − 1.23 TA = +85°C to +105°C (Note 5) 1.14 − 1.26 Detector Voltage Threshold Temperature Coefficient − 30 − ppm/°C VCC to Reset Delay VCC = VTH to (VTH − 100 mV) − 10 − (cid:2)sec Reset Active TimeOut Period (Note 6) tRP msec MAX803SN(Q)293D1 1.0 − 3.3 MAX803SN(Q)293D2/MAX803SN(Q)308D2 20 − 66 MAX803SN(Q)293D3 100 − 330 MAX803SN(Q)293 140 − 460 RESET Output Voltage Low VOL − − 0.3 V VCC = VTH − 0.2 V 1.6 V (cid:4) VTH (cid:4) 2.0 V, ISINK = 0.5 mA 2.1 V (cid:4) VTH (cid:4) 4.0 V, ISINK = 1.2 mA 4.1 V (cid:4) VTH (cid:4) 4.9 V, ISINK = 3.2 mA RESET Leakage Current VCC (cid:5) VTH, RESET De−asserted ILEAK − − 1 (cid:2)A 3. Production testing done at TA = 25°C, over temperature limits guaranteed by design. 4. For NCV automotive devices, this temperature range is TA = −40°C to +125°C. 5. For NCV automotive devices, this temperature range is TA = +85°C to +125°C. 6. Contact your ON Semiconductor sales representative for other threshold voltage and timeout options. www.onsemi.com 3

MAX803 Series, NCP803 Series TYPICAL OPERATING CHARACTERISTICS 0.7 0.5 VTH = 1.2 V VTH = 4.63 V 0.6 85°C A) A) 0.4 (cid:2)NT ( 0.5 25°C (cid:2)NT ( 85°C E E 0.3 R 0.4 R UR UR 25°C C 0.3 C LY −40°C LY 0.2 P P P 0.2 P U U −40°C S S 0.1 0.1 0 0 0.5 1.5 2.5 3.5 4.5 5.5 6.5 0.5 1.5 2.5 3.5 4.5 5.5 6.5 SUPPLY VOLTAGE (V) SUPPLY VOLTAGE (V) Figure 3. Supply Current vs. Supply Voltage Figure 4. Supply Current vs. Supply Voltage 0.4 1.002 E VTH = 2.93 V 85°C TAG 1.001 L O A) 0.3 V 1.000 (cid:2)T ( LD VTH = 4.63 V N 25°C O 0.999 E H R S R 0.2 E 0.998 U −40°C R C H PLY ED T 0.997 VTH = 1.2 V UP 0.1 LIZ 0.996 S A M 0.995 R O 0 N 0.994 0.5 1.5 2.5 3.5 4.5 5.5 6.5 −50 −25 0 25 50 75 100 125 SUPPLY VOLTAGE (V) TEMPERATURE (°C) Figure 5. Supply Current vs. Supply Voltage Figure 6. Normalized Reset Threshold Voltage vs. Temperature 0.5 100 VTH = 4.63 V V) ISINK = 500 (cid:2)A (cid:2)ENT (A) 00..34 VCC = 5.0 V E V (mCC 6800 RESET ASSERTED URR VCC = 3.3 V TAG 85°C C OL Y 0.2 V 40 PL VCC = 1.0 V T 25°C P U U P S 0.1 UT 20 O −40°C 0 0 −50 −25 0 25 50 75 100 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 TEMPERATURE (°C) SUPPLY VOLTAGE (V) Figure 7. Supply Current vs. Temperature Figure 8. Output Voltage Low vs. Supply Voltage www.onsemi.com 4

MAX803 Series, NCP803 Series TYPICAL OPERATING CHARACTERISTICS 125 300 (cid:2)sec) VOD = VCC−VTH (cid:2)sec) VOD = 10 mV VOD = VCC−VTH Y ( 100 Y (240 LA VOD = 10 mV LA E E D D T 75 T 180 E E S S E E N R 50 VOD = 20 mV N R120 VOD = 20 mV W W DO VOD = 100 mV DO VOD = 100 mV − − R 25 R 60 E E OW VOD = 200 mV OW VOD = 200 mV P 0 P 0 −50 −25 0 25 50 75 100 125 −50 −25 0 25 50 75 100 125 TEMPERATURE (°C) TEMPERATURE (°C) Figure 9. Power−Down Reset Delay vs. Figure 10. Power−Down Reset Delay vs. Temperature and Overdrive (V = 1.2 V) Temperature and Overdrive (V = 4.63 V) TH TH T U O 1.3 E M T TI 1.2 E S E R 1.1 P U − R 1.0 E W O P 0.9 D E Z LI 0.8 A M R 0.7 O N −50 −25 0 25 50 75 100 TEMPERATURE (°C) Figure 11. Normalized Power−Up Reset vs. Temperature www.onsemi.com 5

MAX803 Series, NCP803 Series Detail Operation Description The MAX803, NCP803 series microprocessor reset power interruption and V becomes significantly CC supervisory circuits are designed to monitor the power deficient, it will fall below the lower detector threshold supplies in digital systems and provide a reset signal to the (V ). This event causes the RESET output to be in the low TH− processor without any external components. Figure 2 shows state for the MAX803 and NCP803 devices. After the timing diagram and a typical application below. Initially completion of the power interruption, V will rise to its CC consider that input voltage V is at a nominal level greater nominal level and become greater than the V . This CC TH than the voltage detector upper threshold (VTH). And the sequence activates the internal oscillator circuitry and digital counter to count. After the count of the timeout RESET(RESET) output voltage (Pin 2) will be in the high period, the reset output will revert back to the original state. state for MAX803 and NCP803 devices. If there is an input VCC Input Voltage VTH+ VTH– VCC Reset Output VTH– MAX803, NCP803 0V VCC Reset Output VTH– MAX810 0V tRP Figure 12. Timing Waveforms www.onsemi.com 6

MAX803 Series, NCP803 Series APPLICATIONS INFORMATION V Transient Rejection the NCP803/MAX803 has Open−Drain and active−low CC The MAX803/NCP803 series provides accurate VCC output, it typically uses a pullup resistor. With this device, monitoring and reset timing during power−up, RESET will most likely not maintain an active condition, power−down, and brownout/sag conditions, and rejects but will drift to a non−active level due to the pullup resistor negative−going transients (glitches) on the power supply and the reduced sinking capability of the open−drain device. line. Figure 13 shows the maximum transient duration vs. Therefore, this device is not recommended for applications maximum negative excursion (overdrive) for glitch where the RESET pin is required to be valid down to rejection. Any combination of duration and overdrive which V = 0 V. CC lies under the curve will not generate a reset signal. Combinations above the curve are detected as a brownout or VCC power−down. Typically, transient that goes 100 mV below the reset threshold and lasts 5.0 (cid:2)s or less will not cause a reset pulse. Transient immunity can be improved by adding VCC R1 a capacitor in close proximity to the VCC pin of the MAX809 100 k* MAX803. NCP803 RESET VCC GND VTH Overdrive *Assume High−Z Reset Input to Microprocessor Figure 14. RESET Signal Integrity Duration MAX803 RESET Output Allows Use With Two Power c)250 Supplies se In numerous applications the pullup resistor place on the (cid:2) N ( RESET output is connected to the supply voltage monitored O200 TI by the IC. Nevertheless, a different supply voltage can also RA power this output and so level−shift from the monitored U D150 supply to reset the microprocessor. However, if the T NCP803/MAX803’s supply goes blew 1 V, the RESET N SIE100 VTH = 4.63 V output ability to sink current will decrease and the result is N a high state on the pin even though the supply’s IC is under A R the threshold level. This occurs at a V level that depends T CC M 50 VTH = 1.2 V on the R value and the voltage which is connected. U pullup M XI MA 0 VCC1 VCC2 10 60 110 160 210 260 310 360 410 RESET COMPARATOR OVERDRIVE (mV) Figure 13. Maximum Transient Duration vs. VCC Rpullup VCC Overdrive for Glitch Rejection at 25°C MAX803 Microprocessor NCP803 RESET RESET RESET Signal Integrity During Power−Down The MAX803/NCP803 RESET output is valid to V = CC 1.0 V. Below this voltage the output becomes an “open GND GND circuit” and does not sink current. This means CMOS logic inputs to the Microprocessor will be floating at an undetermined voltage. Most digital systems are completely shutdown well above this voltage. However, in situations Figure 15. MAX803 RESET Output with Two Supplies where RESET must be maintained valid to V = 0 V, since CC www.onsemi.com 7

MAX803 Series, NCP803 Series ORDERING, MARKING AND THRESHOLD INFORMATION Vth** Time out*** Part Number (V) (ms) Description Marking Package Shipping† NCP803SN160T1G 1.60 140−460 SCQ SOT23−3 (Pb−Free) NCP803SN232T1G 2.32 140−460 SQR SOT23−3 (Pb−Free) NCP803SN263T1G 2.63 140−460 SQC SOT23−3 (Pb−Free) NCP803SN293T1G 2.93 140−460 SQD SOT23−3 (Pb−Free) NCP803SN308T1G 3.08 140−460 SQE SOT23−3 (Pb−Free) NCP803SN400T1G 4.00 140−460 RAD SOT23−3 (Pb−Free) NCP803SN438T1G 4.38 140−460 SQF SOT23−3 (Pb−Free) NCP803SN463T1G 4.63 140−460 SQG SOT23−3 (Pb−Free) NCP803SN120T1G 1.20 140−460 SSW SOT23−3 (Pb−Free) NCP803SN293D1T1G 2.93 1−3.3 SSX SOT23−3 (Pb−Free) NCP803SN293D2T1G 2.93 20−66 SSY SOT23−3 (Pb−Free) NCP803SN293D3T1G 2.93 100−330 SSZ SOT23−3 3000 / Tape & Reel Open Drain RESET (Pb−Free) MAX803SQ120T1G 1.20 140−460 ZV SC70−3 (Pb−Free) MAX803SQ263T1G 2.63 140−460 SX SC70−3 (Pb−Free) MAX803SQ293T1G 2.93 140−460 ZW SC70−3 (Pb−Free) MAX803SQ308T1G 3.08 140−460 ZX SC70−3 (Pb−Free) NCV803SQ308T1G* 140−460 ZA MAX803SQ438T1G 4.38 140−460 ZY SC70−3 (Pb−Free) MAX803SQ463T1G 4.63 140−460 ZZ SC70−3 (Pb−Free) MAX803SQ293D1T1G 2.93 1−3.3 YA SC70−3 (Pb−Free) MAX803SQ293D2T1G 2.93 20−66 YB SC70−3 (Pb−Free) MAX803SQ308D2T1G 3.08 20−66 SY SC70−3 (Pb−Free) NCV803SQ308D2T1G* 20−66 CY MAX803SQ293D3T1G 2.93 100−330 YC SC70−3 (Pb−Free) NCP803SN293T3G 2.93 140−460 SQD SOT23−3 10000 / Tape & (Pb−Free) Reel †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. *NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and PPAP Capable. **Contact your ON Semiconductor sales representative for other threshold voltage options. ***Contact your ON Semiconductor sales representative for timeout options availability for other threshold voltage options. www.onsemi.com 8

MAX803 Series, NCP803 Series PACKAGE DIMENSIONS SOT−23 (TO−236) CASE 318−08 ISSUE AR D NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH. 0.25 MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF 3 THE BASE MATERIAL. E HE T 4. DPRIMOETNRSUIOSINOSN DS, AONRD G EA DTEO BNUORTR INS.CLUDE MOLD FLASH, 1 2 MILLIMETERS INCHES DIM MIN NOM MAX MIN NOM MAX L A 0.89 1.00 1.11 0.035 0.039 0.044 3Xb L1 A1 0.01 0.06 0.10 0.000 0.002 0.004 b 0.37 0.44 0.50 0.015 0.017 0.020 e VIEW C c 0.08 0.14 0.20 0.003 0.006 0.008 TOP VIEW D 2.80 2.90 3.04 0.110 0.114 0.120 E 1.20 1.30 1.40 0.047 0.051 0.055 e 1.78 1.90 2.04 0.070 0.075 0.080 L 0.30 0.43 0.55 0.012 0.017 0.022 A L1 0.35 0.54 0.69 0.014 0.021 0.027 HE 2.10 2.40 2.64 0.083 0.094 0.104 T 0° −−− 10° 0° −−− 10° A1 c SIDE VIEW SEE VIEW C END VIEW RECOMMENDED SOLDERING FOOTPRINT* 3X 2.90 0.90 3X0.80 0.95 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. www.onsemi.com 9

MAX803 Series, NCP803 Series PACKAGE DIMENSIONS SC−70 (SOT−323) CASE 419−04 ISSUE N D NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. e1 2. CONTROLLING DIMENSION: INCH. MILLIMETERS INCHES 3 DIM MIN NOM MAX MIN NOM MAX A 0.80 0.90 1.00 0.032 0.035 0.040 HE E A1 0.00 0.05 0.10 0.000 0.002 0.004 1 2 A2 0.70 REF 0.028 REF b 0.30 0.35 0.40 0.012 0.014 0.016 c 0.10 0.18 0.25 0.004 0.007 0.010 D 1.80 2.10 2.20 0.071 0.083 0.087 b E 1.15 1.24 1.35 0.045 0.049 0.053 e 1.20 1.30 1.40 0.047 0.051 0.055 e e1 0.65 BSC 0.026 BSC L 0.20 0.38 0.56 0.008 0.015 0.022 HE 2.00 2.10 2.40 0.079 0.083 0.095 c A A2 0.05 (0.002) L A1 SOLDERING FOOTPRINT* 0.65 0.65 0.025 0.025 1.9 0.075 0.9 0.035 0.7 0.028 (cid:6) (cid:7) mm SCALE 10:1 inches *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: N. American Technical Support: 800−282−9855 Toll Free ON Semiconductor Website: www.onsemi.com Literature Distribution Center for ON Semiconductor USA/Canada 19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA Europe, Middle East and Africa Technical Support: Order Literature: http://www.onsemi.com/orderlit Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Phone: 421 33 790 2910 Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Japan Customer Focus Center For additional information, please contact your local Email: orderlit@onsemi.com Phone: 81−3−5817−1050 Sales Representative ◊ www.onsemi.com MAX803/D 10

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: O N Semiconductor: NCP803SN160T1G NCP803SN232T1G NCP803SN263T1G NCP803SN293T1G NCP803SN293T3G NCP803SN308T1G NCP803SN438T1G NCP803SN463T1G MAX803SQ120T1G MAX803SQ293D1T1G MAX803SQ293D2T1G MAX803SQ293D3T1G MAX803SQ293T1G MAX803SQ308T1G MAX803SQ438T1G MAX803SQ463T1G NCP803SN120T1G NCP803SN293D1T1G NCP803SN293D2T1G NCP803SN293D3T1G NCP803SN400T1G NCV803SQ308T1G MAX803SQ308D2T1G MAX803SQ263T1G NCP803SN463D1T1G