NCP585 Tri-Mode 300 mA CMOS LDO Regulator with Enable The NCP585 series of low dropout regulators are designed for portable battery powered applications which require precise output voltage accuracy, low quiescent current, and high ripple rejection. These devices feature an enable function which lowers current http://onsemi.com consumption significantly and are offered in the SOT23−5 and the HSON−6 packages, in fixed output voltages between 0.8 V and 3.3 V. MARKING This series of devices have three modes. Chip Enable (CE mode), DIAGRAMS Fast Transient Mode (FT mode), and Low Power Mode (LP mode). Both the FT and LP mode are utilized via the ECO pin. Features 5 5 SOT23−5 • Tri−mode Operation SN SUFFIX XXXTT • Low Dropout Voltage: 1 CASE 1212 1 Typ 550 mV at 300 mA, Output Voltage = 0.9 V Typ 480 mV at 300 mA, Output Voltage = 1.0 V Typ 310 mV at 300 mA, Output Voltage = 1.5 V • Excellent Line Regulation of 0.01%/V (0.05%/V LP Mode) 6 • Excellent Load Regulation of 15 mV (40 mV FT Mode) HSON−6 XXX • High Output Voltage Accuracy of (cid:2)2% ((cid:2)3% LP mode) 6 SAN SUFFIX XTT CASE 506AE • 1 Ultra−Low Iq Current of: 1 3.5 (cid:2)A (LP mode, Output Voltage < 1.6 V) 80 (cid:2)A (FT mode, Output Voltage < 1.8 V) 60 (cid:2)A (FT mode, Output Voltage = 1.8 V) XXX = Specific Device Code • Very Low Shutdown Current of 0.1 (cid:2)A TT = Traceability Information • Excellent Power Supply Rejection Ratio of 70 dB at f = 1.0 kHz • Low Temperature Drift Coefficient on the Output Voltage of ORDERING INFORMATION (cid:2)100 ppm/°C See detailed ordering and shipping information in the package • Fold Back Protection Circuit dimensions section on page 11 of this data sheet. • Input Voltage up to 6.5 V • *Additional voltage options may be available between These are Pb−Free Devices 0.8 V and 3.3 V in 100 mV steps. Typical Applications • Portable Equipment • Hand−Held Instrumentation • Camcorders and Cameras © Semiconductor Components Industries, LLC, 2009 1 Publication Order Number: July, 2009 − Rev. 14 NCP585/D

NCP585 ECO ECO Vin Vout Vin Vout - - + + Vref Vref Current Limit Current Limit CE GND CE GND Figure 1. Simplified Block Diagram for Active Low Figure 2. Simplified Block Diagram for Active High ECO Vin Vout - + Vref Current Limit CE GND Figure 3. Simplified Block Diagram for Active High with Auto Discharge PIN FUNCTION DESCRIPTION HSON−6 SOT23−5 Pin Name Description 1 1 Vin Power supply input voltage. 2 − NC No Connect. 3 5 Vout Regulated output voltage. 4 4 ECO Mode alternative pin. (VECO = Vin for FT mode; VECO = GND for LP mode) 5 2 GND Power supply ground. 6 3 CE or CE Chip enable pin. http://onsemi.com 2

NCP585 MAXIMUM RATINGS Rating Symbol Value Unit Input Voltage Vin 6.5 V Input Voltage (CE or CE Pin) VCE −0.3 to 6.5 V Input Voltage (ECO Pin) VECO −0.3 to 6.5 V Output Voltage Vout −0.3 to Vin +0.3 V Output Current Iout 350 mA Power Dissipation SOT23−5 PD 250 mW HSON−6 400 ESD Capability, Human Body Model, C = 100 pF, R = 1.5 k(cid:3) ESDHBM 2000 V ESD Capability, Machine Model, C = 200 pF, R = 0 (cid:3) ESDMM 150 V Operating Ambient Temperature Range TA −40 to +85 °C Maximum Junction Temperature TJ(max) 125 °C Storage Temperature Range Tstg −55 to +150 °C Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. ELECTRICAL CHARACTERISTICS (Vin = Vout + 1.0 V, TA = 25°C, unless otherwise noted.) Characteristic Symbol Min Typ Max Unit Input Voltage Vin 1.4 − 6.0 V Output Voltage (1.0 (cid:2)A ≤ Iout ≤ 30 mA) Vout V VECO = Vin Vout x 0.980 − Vout x 1.020 VECO = GND Vout x 0.970 − Vout x 1.030 Line Regulation (Iout = 30 mA, Vout + 0.5 V ≤ Vin ≤ 6.0 V) Regline %/V FT Mode VECO = Vin − 0.01 0.15 LP Mode VECO = GND − 0.05 0.20 Load Regulation Regload mV FT Mode (1.0 mA ≤ Iout ≤ 300 mA), VECO = Vin − 40 70 LP Mode (1.0 mA ≤ Iout ≤ 100 mA), VECO = GND − 15 30 Dropout Voltage (Iout = 300 mA) VDO ECO = H ECO = L ECO = H ECO = L V Vout = 0.9 V − 0.55 0.59 0.78 0.80 1.0 V (cid:3) Vout (cid:3) 1.25 V − 0.48 0.51 0.70 0.75 1.5 V (cid:3) Vout (cid:3) 2.5 V − 0.31 0.32 0.45 0.48 2.8 V (cid:3) Vout (cid:3) 3.3 V − 0.23 0.24 0.35 0.375 Quiescent Current (Iout = 0 mA) Iq FT Mode, VECO = Vin (cid:2)A Vout < 1.8 V − 80 111 Vout ≥ 1.8 V − 60 90 LP Mode, VECO = GND Vout < 1.6 V − 3.5 8.0 Vout ≥ 1.8 V − 4.5 9.0 Output Current (Vin − Vout = 1.0 V) Iout 300 − − mA Shutdown Current (VCE = Vin) ISD − 0.1 1.0 (cid:2)A Output Short Circuit Current (Vout = 0 V) Ilim − 50 − mA Enable Input Threshold Voltage − High Vthenh 1.0 − Vin V Enable Input Threshold Voltage − Low Vthenl 0.0 − 0.3 Output Noise Voltage (10 Hz − 100 kHz) Vn − 30 − (cid:2)Vrm s N−Channel On Resistance for Auto Discharge RLow − 60 − (cid:3) Ripple Rejection RR dB (Iout = 50 mA, Vout = 0.9 V, Vin − Vout = 1.0 V) f = 120 Hz − 75 − f = 1.0 kHz − 70 − f = 10 kHz − 65 − Output Voltage Temperature Coefficient (cid:4)Vout/ − (cid:2)100 − ppm/ (Iout = 30 mA, −40°C ≤ TA ≤ 85°C) (cid:4)T °C http://onsemi.com 3

NCP585 TYPICAL CHARACTERISTICS 1.6 1.6 1.4 1.4 V) V) ( ut 1.2 Vin = Vout nominal +2.0 V ( ut 1.2 Vo Vo Vin = Vout nominal +2.0 V E, 1.0 E, 1.0 G G A A T 0.8 T 0.8 L L O O V V T 0.6 T 0.6 TPU 0.4 Vin = Vout nominal +0.3 V TPU 0.4 Vin = Vout nominal +0.3 V U U O O 0.2 Vout = Vout nominal 0.2 Vout = Vout nominal ECO = H ECO = L 0.0 0.0 0 200 400 600 0 200 400 600 OUTPUT CURRENT, Iout (mA) OUTPUT CURRENT, Iout (mA) Figure 4. Output Voltage vs. Output Current Figure 5. Output Voltage vs. Output Current 1.1 1.1 1.0 1.0 (V) ut 0.9 (V) ut 0.9 Vo 0.8 Vo 0.8 E, E, G 0.7 G 0.7 A A T 0.6 T 0.6 L L VO 0.5 Iout = 1.0 mA VO 0.5 Iout = 1.0 mA PUT 0.4 Iout = 30 mA PUT 0.4 Iout = 30 mA UT 0.3 Iout = 50 mA UT 0.3 Iout = 50 mA O O 0.2 Vout = 0.9 V 0.2 Vout = 0.9 V ECO = H ECO = L 0.1 0.1 0.1 1.1 2.1 3.1 4.1 5.1 6.1 0.1 1.1 2.1 3.1 4.1 5.1 6.1 INPUT VOLTAGE, Vin (V) INPUT VOLTAGE, Vin (V) Figure 6. Output Voltage vs. Input Voltage Figure 7. Output Voltage vs. Input Voltage 1.9 1.9 1.7 1.7 V) V) ( ut 1.5 ( ut 1.5 o o V V E, 1.3 E, 1.3 G G A A T 1.1 T 1.1 L L O O V V T 0.9 T 0.9 U U TP 0.7 Iout = 1.0 mA TP 0.7 Iout = 1.0 mA U U O 0.5 Iout = 30 mA Vout = 1.8 V O 0.5 Iout = 30 mA Vout = 1.8 V Iout = 50 mA ECO = H Iout = 50 mA ECO = L 0.3 0.3 0.3 1.3 2.3 3.3 4.3 5.3 6.3 0.3 1.3 2.3 3.3 4.3 5.3 6.3 INPUT VOLTAGE, Vin (V) INPUT VOLTAGE, Vin (V) Figure 8. Output Voltage vs. Input Voltage Figure 9. Output Voltage vs. Input Voltage http://onsemi.com 4

NCP585 TYPICAL CHARACTERISTICS 100 8 90 A) A) 7 (cid:2) 80 (cid:2) q( q( 6 T, I 70 T, I EN 60 EN 5 R R R R U 50 U 4 C C NT 40 NT 3 CE 30 CE S S 2 E 20 E QUI 10 Vout = 0.9 V QUI 1 Vout = 0.9 V ECO = H ECO = L 0 0 0.1 1.1 2.1 3.1 4.1 5.1 6.1 0.1 1.1 2.1 3.1 4.1 5.1 6.1 INPUT VOLTAGE, Vin (V) INPUT VOLTAGE, Vin (V) Figure 10. Quiescent Current vs. Input Voltage Figure 11. Quiescent Current vs. Input Voltage 80 8 A) 70 A) 7 (cid:2) (cid:2) q( 60 q( 6 T, I T, I N 50 N 5 E E R R R R U 40 U 4 C C NT 30 NT 3 E E C C S 20 S 2 E E QUI 10 VEoCuOt = = 1 H.8 V QUI 1 VEoCuOt = = 1 L.8 V 0 0 0.3 1.3 2.3 3.3 4.3 5.3 6.3 0.3 1.3 2.3 3.3 4.3 5.3 6.3 INPUT VOLTAGE, Vin (V) INPUT VOLTAGE, Vin (V) Figure 12. Quiescent Current vs. Input Voltage Figure 13. Quiescent Current vs. Input Voltage 0.93 0.93 V) 0.92 V)0.92 E, V( out 0.91 E, V( out0.91 G G A A LT 0.90 LT0.90 O O V V UT 0.89 UT 0.89 P P T T U U O 0.88 Vout = 0.9 V O0.88 Vout = 0.9 V ECO = H ECO = L 0.87 0.87 −50 −25 0 25 50 75 100 −50 −25 0 25 50 75 100 TEMPERATURE (°C) TEMPERATURE (°C) Figure 14. Output Voltage vs. Temperature Figure 15. Output Voltage vs. Temperature http://onsemi.com 5

NCP585 TYPICAL CHARACTERISTICS 1.23 1.23 V) 1.22 V) 1.22 ( O ( O D 1.21 D1.21 V V E, E, G 1.20 G 1.20 A A T T L L O 1.19 O 1.19 V V T T PU 1.18 PU 1.18 T T U U O 1.17 Vout = 1.2 V O 1.17 Vout = 1.2 V ECO = H ECO = L 1.16 1.16 −50 −25 0 25 50 75 100 −50 −25 0 25 50 75 100 TEMPERATURE (°C) TEMPERATURE (°C) Figure 16. Output Voltage vs. Temperature Figure 17. Output Voltage vs. Temperature 0.8 0.8 V) 0.7 V) 0.7 GE, V (DO 00..65 85°C GE, V( DO00..65 85°C VOLTA 0.4 VOLTA 0.4 25°C OUT 0.3 −40°C 25°C OUT 0.3 −40°C OP 0.2 OP 0.2 R R D 0.1 Vout = 0.9 V D 0.1 Vout = 0.9 V ECO = H ECO = L 0.0 0.0 0 50 100 150 200 250 300 0 50 100 150 200 250 300 OUTPUT CURRENT, Iout (mA) OUTPUT CURRENT, Iout (mA) Figure 18. Dropout Voltage vs. Output Current Figure 19. Dropout Voltage vs. Output Current 0.7 0.7 V) 0.6 V) 0.6 ( O ( O VD 0.5 VD 0.5 GE, 85°C GE, 85°C A 0.4 A 0.4 OLT OLT V 0.3 V 0.3 UT 25°C UT 25°C O 0.2 O 0.2 ROP −40°C ROP −40°C D 0.1 Vout = 1.2 V D 0.1 Vout = 1.2 V ECO = H ECO = L 0.0 0.0 0 50 100 150 200 250 300 0 50 100 150 200 250 300 OUTPUT CURRENT, Iout (mA) OUTPUT CURRENT, Iout (mA) Figure 20. Dropout Voltage vs. Output Current Figure 21. Dropout Voltage vs. Output Current http://onsemi.com 6

NCP585 TYPICAL CHARACTERISTICS 0.40 0.40 V) 0.35 V) 0.35 ( DO 0.30 ( DO 0.30 V V GE, 0.25 85°C GE, 0.25 85°C A A LT 0.20 LT 0.20 T VO 0.15 25°C T VO 0.15 25°C U U O −40°C O P 0.10 P 0.10 RO RO −40°C D 0.05 Vout = 1.8 V D 0.05 Vout = 1.8 V ECO = H ECO = L 0.00 0.00 0 50 100 150 200 250 300 0 50 100 150 200 250 300 OUTPUT CURRENT, Iout (mA) OUTPUT CURRENT, Iout (mA) Figure 22. Dropout Voltage vs. Output Current Figure 23. Dropout Voltage vs. Output Current 100 100 ON, RR (dB) 76890000 Iout = 30 mA Iout = 1.0 mA ON, RR (dB) 76890000 VVCoionuu t=t == 1 0.29..9 2V V(cid:2) +F ,0 E.2C VOp −=p L CTI 50 TI 50 REJE 40 Iout = 50 mA EJEC 40 Iout = 1.0 mA PPLE 3200 Vout = 0.9 V PLE R 3200 Iout = 30 mA RI Vin = 1.9 V + 0.2 Vp−p RIP 100 Cout = 2.2 (cid:2)F, ECO = H 100 Iout = 50 mA 0 1 10 100 0 1 10 100 FREQUENCY, f (kHz) FREQUENCY, f (kHz) Figure 24. Ripple Rejection vs. Frequency Figure 25. Ripple Rejection vs. Frequency 100 100 90 90 Vout = 1.2 V ON, RR (dB) 768000 Iout = 30 mA N, RR (dB) 768000 VCionu =t = 2 .22. 2V (cid:2) +F ,0 E.2C VOp −=p L CTI 50 Iout = 1.0 mA TIO 50 EJE 40 JEC 40 Iout = 1.0 mA R E PPLE 3200 Vout = 1.2 V Iout = 50 mA PLE R 3200 Iout = 30 mA RI 10 VCionu =t = 2 .22. 2V (cid:2) +F ,0 E.2C VOp −=p H RIP 10 Iout = 50 mA 0 0 0 1 10 100 0 1 10 100 FREQUENCY, f (kHz) FREQUENCY, f (kHz) Figure 26. Ripple Rejection vs. Frequency Figure 27. Ripple Rejection vs. Frequency http://onsemi.com 7

NCP585 TYPICAL CHARACTERISTICS 0.98 4.1 3.1 4.1 Input Voltage Input Voltage V)0.96 3.1 V)2.6 3.1 OUTPUT VOLTAGE, V (out0000....99984208 Output VoECltCoauOgt e= = T Ha,n Itaoulut m= 310.0 m (cid:2)AF −2101...111.1INPUT VOLTAGE, V (V)inOUTPUT VOLTAGE, V (out2110....1616 Output VoltECagCoeuOt = = T La,n Itoaultu =m 3 10. 0m (cid:2)AF −2101...111.1INPUT VOLTAGE, V (V)in 0.86 Vout = 0.9 V −2.1 0.1 Vout = 0.9 V −2.1 0 10 20 30 40 50 60 70 80 90 100 0.0 0.4 0.8 1.2 1.6 2.0 2.4 2.8 3.2 3.6 4.0 TIME, t ((cid:2)s) TIME, t (ms) Figure 28. Input Transient Response 1.3 150 1.3 60 OLTAGE, V(V) out111...102 ECCCionu O=t = =T aT Han,nt aVtaluilnum =m 1 11..0.90 (cid:2) L V(cid:2)FoFad Current 501000 URRENT, I(mA) outOLTAGE, V(V) out111...102 ECCCionu O=t = =T aT Han,nt aVtaluilnum L=m o 1 1a1..0d.90 (cid:2) C V(cid:2)FuFrrent 0−3030URRENT, I(mA) out OUTPUT V00..98 Vout = 0.9 V Output Voltage −−51000OUTPUT C OUTPUT V00..98 Vout = 0.9 V Output Voltage −−6900OUTPUT C 0.7 −150 0.7 −120 0 5 10 15 20 25 30 35 40 0 5 10 15 20 25 30 35 40 Time, t ((cid:2)s) Time, t ((cid:2)s) 1.3 60 3.1 20 GE, V(V) out11..12 ECO = H, Vin = 1.9L oVad Current 030 NT, I(mA) outGE, V(V) out22..16 Load Current 010 NT, I(mA) out OUTPUT VOLTA100...098 CCVoionuu t=t == T 0aT.an9nt aVtalulumm 1 2.0.2 (cid:2) O(cid:2)FFutput Voltage −−−369000OUTPUT CURREOUTPUT VOLTA110...616 ECCVoCionuu Ot=t == =T 0aT H.an9,ntO aVVtaluuilntump =mu 1t 1 1.V.0.9o0 (cid:2) l Vt(cid:2)FaFge −−−123000OUTPUT CURRE 0.7 −120 0.1 −40 0 5 10 15 20 25 30 35 40 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 Time, t ((cid:2)s) Time, t (ms) Figure 29. Load Transient Response http://onsemi.com 8

NCP585 TYPICAL CHARACTERISTICS 2.8 2.6 2.8 2.6 V) 1.9 2.1V)V)1.9 2.1V) E, V (CE 1.0 VCE = 0 V → 1.9 V 1.6E, V (outE, V (CE1.0 VCE = 0 V → 1.9 V 1.6E, V (out G GG G OLTA 0.1 1.1OLTAOLTA0.1 1.1OLTA V VV V UT −1.0 ECO = H 0.6UT UT −1.0 ECO = L 0.6UT NP Vin = 1.9 V TPNP Vin = 1.9 V TP CE I−1.9 CCionu =t = T aTanntatalulumm 1 1.0.0 (cid:2) (cid:2)FF 0.1OUCE I−1.9 CCionu =t = T aTanntatalulumm 1 1.0.0 (cid:2) (cid:2)FF 0.1OU Iout = 300 mA Iout = 300 mA −2.8 −0.6 −2.8 −0.6 −30 −20 −10 0 10 20 30 40 50 60 70 −0.3 −0.2 −.01 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 TIME, t ((cid:2)s) TIME, t (ms) Figure 30. Turn−On Speed with CE Pin, V = 0.8 V out V = 1.9 V, C = Tantalum 1.0 (cid:2)F, C = Tantalum 1.0 (cid:2)F, V = 0.9 V in in out out 3.1 VECO = 0 V to 1.9 V 2.1 1.1 0.1 0.91 Iout = 1 mA V) VOLTAGE, V (V)out000000......989989091091 IIoouutt == 5100 mmAA VOLTAGE, V (ECO UT 0.90 UT P 0.89 P T N OU 0.91 Iout = 100 mA O I 0.90 EC 0.89 0.91 Iout = 200 mA 0.90 0.89 Iout = 300 mA 0.91 0.90 0.89 0.88 −0.2 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 TIME, t (ms) Figure 31. Output Voltage at Mode Alternative Point http://onsemi.com 9

NCP585 TYPICAL CHARACTERISTICS 100000 100000 Unstable Cout = 0.1 (cid:2)F Unstable Cout = 1.0 (cid:2)F (cid:3))10000 Region Vout = 1.8 V (cid:3))10000 Region Vout = 1.8 V R ( FT Mode R ( FT Mode S S E 1000 E 1000 R R O O T 100 T 100 CI Stable Region CI Stable Region A A P 10 P 10 A A C C T T U 1 U 1 P P T T U U O 0.1 O 0.1 No unstable region in LP Mode No unstable region in LP Mode 0.01 0.01 0 50 100 150 200 250 300 0 50 100 150 200 250 300 OUTPUT CURRENT (mA) OUTPUT CURRENT (mA) Figure 32. Output Stability, Output Capacitor ESR Figure 33. Output Stability, Output Capacitor vs. Output Load Current (0.1 (cid:2)F) ESR vs. Output Load Current (1.0 (cid:2)F) 100000 100000 Unstable Cout = 10 (cid:2)F Unstable Cout = 100 (cid:2)F (cid:3))10000 Region Vout = 1.8 V (cid:3))10000 Region Vout = 1.8 V R ( FT Mode R ( FT Mode S S E 1000 E 1000 R R O O T 100 T 100 CI Stable Region CI Stable Region A A P 10 P 10 A A C C T T U 1 U 1 P P T T U U O 0.1 O 0.1 No unstable region in LP Mode No unstable region in LP Mode 0.01 0.01 0 50 100 150 200 250 300 0 50 100 150 200 250 300 OUTPUT CURRENT (mA) OUTPUT CURRENT (mA) Figure 34. Output Stability, Output Capacitor Figure 35. Output Stability, Output Capacitor ESR ESR vs. Output Load Current (10 (cid:2)F) vs. Output Load Current (100 (cid:2)F) APPLICATION INFORMATION Input Decoupling Output Decoupling A 1.0 (cid:2)F ceramic capacitor is the recommended value to It is best to use a 1.0 (cid:2)F capacitor value on the V pin. out be connected between V and GND. For PCB layout For better performance, select a capacitor with low in considerations, the traces on V and GND should be Equivalent Series Resistance (ESR). For PCB layout in sufficiently wide in order to minimize noise and prevent considerations, place the output capacitor close to the unstable operation. output pin and keep the leads short as possible. http://onsemi.com 10

NCP585 ORDERING INFORMATION Nominal Device Output Type / Features Output Voltage Marking Package Shipping† NCP585DSAN09T1G Active High w/Auto Discharge, 0.9 B09D HSON−6 3000 Tape & Reel LP and FT Mode (Pb−Free) NCP585DSAN12T1G Active High w/Auto Discharge, 1.2 B12D HSON−6 3000 Tape & Reel LP and FT Mode (Pb−Free) NCP585DSAN18T1G Active High w/Auto Discharge, 1.8 B18D HSON−6 3000 Tape & Reel LP and FT Mode (Pb−Free) NCP585DSN09T1G Active High w/Auto Discharge, 0.9 R09 SOT23−5 3000 Tape & Reel LP and FT Mode (Pb−Free) NCP585DSN12T1G Active High w/Auto Discharge, 1.2 R12 SOT23−5 3000 Tape & Reel LP and FT Mode (Pb−Free) NCP585DSN125T1G Active High w/Auto Discharge, 1.25 R01 SOT23−5 3000 Tape & Reel LP and FT Mode (Pb−Free) NCP585DSN15T1G Active High w/Auto Discharge, 1.5 R15 SOT23−5 3000 Tape & Reel LP and FT Mode (Pb−Free) NCP585DSN18T1G Active High w/Auto Discharge, 1.8 R18 SOT23−5 3000 Tape & Reel LP and FT Mode (Pb−Free) NCP585DSN25T1G Active High w/Auto Discharge, 2.5 R25 SOT23−5 3000 Tape & Reel LP and FT Mode (Pb−Free) NCP585DSN28T1G Active High w/Auto Discharge, 2.8 R28 SOT23−5 3000 Tape & Reel LP and FT Mode (Pb−Free) NCP585DSN30T1G Active High w/Auto Discharge, 3.0 R30 SOT23−5 3000 Tape & Reel LP and FT Mode (Pb−Free) NCP585DSN33T1G Active High w/Auto Discharge, 3.3 R33 SOT23−5 3000 Tape & Reel LP and FT Mode (Pb−Free) NCP585HSAN09T1G Active High, 0.9 B09B HSON−6 3000 Tape & Reel LP and FT Mode (Pb−Free) NCP585HSAN12T1G Active High, 1.2 B12B HSON−6 3000 Tape & Reel LP and FT Mode (Pb−Free) NCP585HSAN18T1G Active High, 1.8 B18B HSON−6 3000 Tape & Reel LP and FT Mode (Pb−Free) NCP585HSN09T1G Active High, 0.9 Q09 SOT23−5 3000 Tape & Reel LP and FT Mode (Pb−Free) NCP585HSN10T1G Active High, 1.0 Q10 SOT23−5 3000 Tape & Reel LP and FT Mode (Pb−Free) NCP585HSN12T1G Active High, 1.2 Q12 SOT23−5 3000 Tape & Reel LP and FT Mode (Pb−Free) NCP585HSN18T1G Active High, 1.8 Q18 SOT23−5 3000 Tape & Reel LP and FT Mode (Pb−Free) NCP585HSN30T1G Active High, 3.0 Q30 SOT23−5 3000 Tape & Reel LP and FT Mode (Pb−Free) NCP585LSAN09T1G Active Low, 0.9 B09A HSON−6 3000 Tape & Reel LP and FT Mode (Pb−Free) NCP585LSAN12T1G Active Low, 1.2 B12A HSON−6 3000 Tape & Reel LP and FT Mode (Pb−Free) NCP585LSAN18T1G Active Low, 1.8 B18A HSON−6 3000 Tape & Reel LP and FT Mode (Pb−Free) NCP585LSN09T1G Active Low, 0.9 P09 SOT23−5 3000 Tape & Reel LP and FT Mode (Pb−Free) NCP585LSN12T1G Active Low, 1.2 P12 SOT23−5 3000 Tape & Reel LP and FT Mode (Pb−Free) NCP585LSN18T1G Active Low, 1.8 P18 SOT23−5 3000 Tape & Reel LP and FT Mode (Pb−Free) †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specification Brochure, BRD8011/D. Other voltages are available. Consult your ON Semiconductor representative. http://onsemi.com 11

NCP585 PACKAGE DIMENSIONS SOT23−5 SN SUFFIX CASE 1212−01 ISSUE O NOTES: 1. DIMENSIONS ARE IN MILLIMETERS. A2 2. INTERPRET DIMENSIONS AND TOLERANCES A D B PER ASME Y14.5M, 1994. 0.05 S A1 3. DATUM C IS A SEATING PLANE. MILLIMETERS E 5 4 L DIM MIN MAX 1 2 3 A1 0.00 0.10 A2 1.00 1.30 E1 B 0.30 0.50 L1 B 5X C CD 02..1800 03..2050 0.10 M C B S A S C E 2.50 3.10 E1 1.50 1.80 e e 0.95 BSC e1 e1 1.90 BSC L 0.20 --- L1 0.45 0.75 SOLDERING FOOTPRINT* 1.9 0.074 0.95 0.037 2.4 0.094 1.0 0.039 0.7 (cid:4) (cid:5) 0.028 SCALE 10:1 mm inches *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 12

NCP585 PACKAGE DIMENSIONS HSON−6 SAN SUFFIX CASE 506AE−01 ISSUE A D A B NOTES: PIN ONE 6 4 1. DIMENSIONING AND TOLERANCING PER REFERENCE ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: 2 X E1 E MILLIMETERS. 0.20 C 3. DIMENSION b APPLIES TO PLATED TERMINAL AND IS MEASURED BETWEEN 2 X 1 3 0.10 AND 0.15 MM FROM TERMINAL. 4. COPLANARITY APPLIES TO THE 0.20 C EXPOSED PAD AS WELL AS THE TERMINALS. TOP VIEW MILLIMETERS DIM MIN MAX 0.10 C A 0.70 0.90 A3 0.15 REF A b 0.20 0.40 6 X 0.08 C D 2.90 BSC (A3) D2 1.40 1.60 SEATING C E 3.00 BSC PLANE SIDE VIEW E1 2.80 BSC E2 1.50 1.70 e 0.95 BSC L 0.15 0.25 D2 e 1 3 L 6 X E2 EXPOSED PAD 6 4 b 6 X NOTE 3 BOTTOM VIEW 0.10 C A B 0.05 C ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: N. American Technical Support: 800−282−9855 Toll Free ON Semiconductor Website: www.onsemi.com Literature Distribution Center for ON Semiconductor USA/Canada P.O. Box 5163, Denver, Colorado 80217 USA Europe, Middle East and Africa Technical Support: Order Literature: http://www.onsemi.com/orderlit Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Phone: 421 33 790 2910 Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Japan Customer Focus Center For additional information, please contact your loca Email: orderlit@onsemi.com Phone: 81−3−5773−3850 Sales Representative http://onsemi.com NCP585/D 13

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: O N Semiconductor: NCP585DSN09T1G NCP585DSN125T1G NCP585DSN12T1G NCP585DSN18T1G NCP585DSN28T1G NCP585HSN09T1G NCP585HSN12T1G NCP585HSN18T1G NCP585LSN09T1G NCP585LSN12T1G NCP585LSN18T1G NCP585DSN15T1G NCP585DSN25T1G NCP585DSN30T1G NCP585DSN33T1G NCP585HSN10T1G NCP585HSN30T1G