E M C C o m p o n e n t s May 2018 Chip beads For power line GHz noise countermeasure MPZ-E series MPZ1005-E type MPZ1005-E 1005[0402 inch]* * Dimensions code JIS[EIA]

(2/10) E M C C o m p o n e n t s REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The storage period is less than 12 months.Be sure to follow the storage conditions (temperature:5 to 40°C, humidity:10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150°C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equip- ment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equip- ment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or qual- ity require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/aviation equipment (8) Public information-processing equipment (2) Transportation equipment (cars, electric trains, ships, etc.) (9) Military equipment (3) Medical equipment (10) Electric heating apparatus, burning equipment (4) Power-generation control equipment (11) Disaster prevention/crime prevention equipment (5) Atomic energy-related equipment　　 (12) Safety equipment (6) Seabed equipment (13) Other applications that are not considered general-purpose (7) Transportation control equipment applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing pro- tection circuit/device or providing backup circuits in your equipment. 20180521 / beads_commercial_power_mpz1005-e_en.fm

(3/10) E M C C o m p o n e n t s Chip beads Product compatible with RoHS directive Halogen-free For power line Compatible with lead-free solders GHz noise countermeasure Overview of MPZ1005-E type FEATURES Noise reduction solution for power line. Lineup includes products with material S, which can attain impedance from low frequency bands to high frequency bands at GHz bands, and products with material Y, where impedance is steeply raised at GHz bands. Compared to the MPZ series, it can attain high impedance at GHz bands. Compared to the MMZ-E series, has low direct current resistance for compatibility with large currents, optimal for low power consump- tion. Performs well even in signal lines where low direct current resistance is required. APPLICATION Noise removal for mobile devices such as smartphones and tablet terminals, and various modules. Noise removal for PCs and recorders, household appliances such as STBs, smart grids, and industrial equipment. PART NUMBER CONSTRUCTION MPZ 1005 S 121 E T 000 L×W×T dimensions Impedance Characteristic Series name Material name Packaging style Internal code (mm) () at 100MHz type 1005 1.0×0.5x0.5 S 221 220 E T Taping 000 A 121 120 D F OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Temperature ranges Package quantity Individual weight Type Operating Storage temperature temperature （°C） （°C） (pieces/reel) （mg） MPZ1005-E –55 to +125 –55 to +125 10,000 1 The storage temperature range is for after the circuit board is mounted. RoHS Directive Compliant Product: See the following for more details.https://product.tdk.com/info/en/environment/rohs/index.html Halogen-free: indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm. Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_power_mpz1005-e_en.fm

(4/10) E M C C o m p o n e n t s MPZ1005-E type RECOMMENDED REFLOW PROFILE Preheating Soldering Natural cooling Peak T4 e ur T3 T3 at er p m e T T2 T: t3 T1 t1 t2 t: Time Preheating Soldering Peak Temp. Time Temp. Time Temp. Time T1 T2 t1 T3 t2 T4 t3 150°C 180°C 60 to 120s 230°C 30 to 60s 250 to 260°C 10s Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_power_mpz1005-e_en.fm

(5/10) E M C C o m p o n e n t s MPZ1005-E type MATERIAL CHARACTERISTIC S material: Standard type that features impedance characteristics similar to those of a typical ferrite core. For signal line applications in which the blocking region is near 100MHz. Impedance values selected for effectiveness at 40 to 300MHz. A material: This high-impedance product is based on the impedance frequency characteristics of our Y-material. The product offers excellent impedance characteristics, which is greater than 2500, in the vicinity of 100MHz range (MMZ1608A252B). D material: For applications calling for low insertion loss at low frequencies and sharply increasing impedance at high frequencies. Designed for high impedance at high frequencies (300MHz to 1GHz) for signal line applications. F material: This new product inherits the characteristic of our D-material, namely its sharp impedance rise time, and its impedance peak frequency has been shifted higher into range. The product offers excellent noise suppression from 600MHz to as high as in the GHz range. TYPICAL MATERIAL IMPEDANCE CHARACTERISTICS 2500 A D F 2000 1500 1000 S 500 0 10 100 1000 Frequency(MHz) Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_power_mpz1005-e_en.fm

(6/10) E M C C o m p o n e n t s MPZ1005-E type SHAPE & DIMENSIONS 1±0.05 5 0 0. ± 5 0. 5 0 0. ± 5 0. 0.1min. Dimensions in mm RECOMMENDED LAND PATTERN 5 0. 0.5 0.4 0.5 Dimensions in mm Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_power_mpz1005-e_en.fm

(7/10) E M C C o m p o n e n t s MPZ1005-E type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Impedance DC resistance Rated current Part No. [100MHz] [1GHz] () Tolerance () Tolerance ()max. (A)max. 120 ±25% 200 ±40% 0.095 1.50 MPZ1005S121ET000 220 ±25% 350 ±40% 0.220 0.90 MPZ1005S221ET000 330 ±25% 550 ±40% 0.280 0.70 MPZ1005S331ET000 150 ±25% 350 ±40% 0.180 0.80 MPZ1005A151ET000 330 ±25% 800 ±40% 0.300 0.60 MPZ1005A331ET000 33 ±25% 200 ±40% 0.180 0.80 MPZ1005D330ET000 75 ±25% 500 ±40% 0.300 0.60 MPZ1005D750ET000 33 ±25% 400 ±40% 0.350 0.55 MPZ1005F330ET000 47 ±25% 600 ±40% 0.450 0.45 MPZ1005F470ET000  Please refer to the graph of rated current vs. temperature characteristics (derating) about the rating current at 85°C or more in temperature of the product. ○Measurement equipment Measurement item Product No. Manufacturer Impedance E4991A+16192A Keysight Technologies DC resistance Type-7556 Yokogawa ＊ Equivalent measurement equipment may be used. ○ Rated current vs. temperature characteristics (derating) 1.6 1.4 S121E 1.2 )A A151E, D330E (nt 1.0 S221E e curr0.8 S331E ed 0.6 A331E at R 0.4 F470E D750E, F330E 0.2 0.0 –55 –35 –15 5 25 45 65 85 105 125 Temperature (°C) Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_power_mpz1005-e_en.fm

(8/10) E M C C o m p o n e n t s MPZ1005-E type ELECTRICAL CHARACTERISTICS Z VS. FREQUENCY CHARACTERISTICS (BY SERIES) MPZ1005S-E series MPZ1005A-E series MPZ1005D-E series 600 900 700 MPZ1005S331E MPZ1005D750E 800 500 MPZ1005A331E 600 700 MPZ1005S221E 500 400 600 Ω) MPZ1005S121E Ω) Ω) (e (e 500 (e 400 nc300 nc nc a a a ed ed400 ed300 p p p m m m I200 I300 I 200 200 100 MPZ1005A151E 100 100 MPZ1005D330E 0 0 0 1 10 100 1000 10000 1 10 100 1000 10000 1 10 100 1000 10000 Frequency (MHz) Frequency (MHz) Frequency (MHz) MPZ1005F-E series 1200 MPZ1005F470E 1000 800 600 Ω) MPZ1005F330E (e 400 c n a d e 200 p m I 0 1 10 100 1000 10000 Frequency (MHz) Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_power_mpz1005-e_en.fm

(9/10) E M C C o m p o n e n t s MPZ1005-E type ELECTRICAL CHARACTERISTICS Z, X, R VS. FREQUENCY CHARACTERISTICS MPZ1005S121ET000 MPZ1005S221ET000 MPZ1005S331ET000 250 400 600 350 Ω()Impedance 12100550000 ZR X Ω()Impedance 12312000555000000 RZ X Ω()Impedance 135240000000000 ZR X 0 0 0 1 10 100 1000 10000 1 10 100 1000 10000 1 10 100 1000 10000 Frequency (MHz) Frequency (MHz) Frequency (MHz) MPZ1005A151ET000 MPZ1005A331ET000 MPZ1005D330ET000 400 900 350 350 800 300 Ω()Impedance 12312000555000000 Z R X Ω()Impedance 123456700000000000000 Z RX Ω()Impedance 11225050500000 Z RX 0 0 0 1 10 100 1000 10000 1 10 100 1000 10000 1 10 100 1000 10000 Frequency (MHz) Frequency (MHz) Frequency (MHz) MPZ1005D750ET000 MPZ1005F330ET000 MPZ1005F470ET000 700 800 1200 600 1000 Ω()dance 345000000 Z R Ω()dance 460000 Z R Ω()dance 680000 Z R pe 200 pe pe 400 Im 100 X Im 200 X Im 200 X 0 0 0 1 10 100 1000 10000 1 10 100 1000 10000 1 10 100 1000 10000 Frequency (MHz) Frequency (MHz) Frequency (MHz) Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_power_mpz1005-e_en.fm

(10/10) E M C C o m p o n e n t s MPZ1005-E type PACKAGING STYLE REEL DIMENSIONS 2.0±0.5 n. mi 0 6 ø 1.0 ø13±0.2 8.4+–02..00 ø21±0.8 14.4max. ø180±2.0 Dimensions in mm TAPE DIMENSIONS 1 0. 1.5+00.1 2.0±0.05 4.0±0.1 75± 1. 5 0 ±0. 0.3 5 ± B 3. 8.0 A P1 K Dimensions in mm Type A B P1 K MPZ1005-E 0.65±0.1 1.15±0.1 2.0±0.05 0.8max. 160min. Taping 200min. Drawing direction 300min. Dimensions in mm Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use. Please note that the contents may change without any prior notice due to reasons such as upgrading. 20180521 / beads_commercial_power_mpz1005-e_en.fm

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: T DK: MPZ1005F470ET000 MPZ1005F330ET000 MPZ1005A331ET000 MPZ1005D330ET000 MPZ1005A151ET000 MPZ1005S121ET000 MPZ1005D750ET000 MPZ1005S221E MPZ1005S331E MPZ1005S331ET000 MPZ1005S221ET000 MPZ1005A151ETD25 MPZ1005A331ETD25 MPZ1005D330ETD25 MPZ1005D750ETD25