® MP900 and MP9000 Series Kool-Pak Power Film Resistors TO-126, TO-220 and TO-247 Style Page 1 of 2 MP916 Standard Resistance Values: Tolerance MP916 ±5% Standard (20% is available). 0.010 Ω 5% 0.015 Ω 5% MP915, MP925, and MP930 Standard Resistance Values: Tolerance MP915, MP925, and MP930 ±1% Standard - except as noted. (5% and 20% are available for most resistance values). 0.020 Ω 5% 0.33 Ω 7.50 Ω 50.0 Ω 500 Ω 10.0 K 0.025 Ω 5% 0.40 Ω 8.00 Ω 56.0 Ω 560 Ω 15.0 K 0.030 Ω 5% 0.50 Ω 10.0 Ω 75.0 Ω 750 Ω 20.0 K 0.033 Ω 5% 0.75 Ω 12.0 Ω 100 Ω 1.00 K 25.0 K 0.040 Ω 5% 1.00 Ω 15.0 Ω 120 Ω 1.50 K 30.0 K 0.050 Ω 1.50 Ω 20.0 Ω 150 Ω 2.00 K 33.0 K 0.075 Ω 2.00 Ω 25.0 Ω 200 Ω 2.50 K 40.0 K 0.10 Ω 2.50 Ω 27.0 Ω 250 Ω 3.00 K 47.0 K 0.15 Ω 3.00 Ω 30.0 Ω 300 Ω 3.30 K 50.0 K 0.20 Ω 3.30 Ω 33.0 Ω 330 Ω 4.00 K 56.0 K 0.25 Ω 4.00 Ω 40.0 Ω 400 Ω 5.00 K 68.0 K Low Cost Heat Sink Mountable Design featuring 0.30 Ω 5.00 Ω 47.0 Ω 470 Ω 7.50 K 75.0 K 82.0 K an Exposed Ceramic Heat Dissipating Mounting Surface 100 K Use your thermal design experience with power semiconductors in TO-126, TO-220, MP9100 Standard Resistance Values: and TO-247 style power packages to help you get the most out of this unique family of Tolerance MP9100 ±1% Standard. power resistors. The thermal design issues are the same where power handling 0.050 Ω 0.40 Ω 3.30 Ω 20.0 Ω 56.0 Ω capability is based on the case temperature which is maintained in your design. 0.075 Ω 0.50 Ω 4.00 Ω 25.0 Ω 75.0 Ω 0.10 Ω 0.75 Ω 5.00 Ω 27.0 Ω 100 Ω 0.15 Ω 1.00 Ω 7.50 Ω 30.0 Ω MP915 TO-126 Style Power Package 00..2205 ΩΩ 12..5000 ΩΩ 81.00.00 ΩΩ 3430..00 ΩΩ • 0.30 Ω 2.50 Ω 12.0 Ω 47.0 Ω 15 Watts at +25°C Case Temperature, derated to zero at +150°C. 0.33 Ω 3.00 Ω 15.0 Ω 50.0 Ω • Exposed Ceramic Heat Dissipating Mounting Surface. • Resistance Range of 0.020 ohm to 1 K. • Non-Inductive Design. For custom resistance values and tolerances contact applications engineering. MP916, MP925, and MP930 TO-220 Style Power Package • Up to 30 Watts at +25°C Case Temperature, derated to zero at +150°C. Ordering Information: • Exposed Ceramic Heat Dissipating Mounting Surface. MP915 - 50.0 - 1% • Resistance Range of 0.010 ohm to 100 K. Model Number: Tolerance • Non-Inductive Design. Resistor Value: Packaging: MP915, MP916, MP925, MP930 MP9100 TO-247 Style Power Package resistors are packaged in plastic shipping tubes, 50 pieces per tube. These resistors are available • 100 Watts at +25°C Case Temperature, derated to zero at +175°C. in a 50 piece minimum quantity and in full tube • Exposed Ceramic Heat Dissipating Mounting Surface. quantity increments (i.e. 50, 100, 150, etc.). The • Resistance Range of 0.050 ohm to 100 ohm. MP9100 resistors are packaged in plastic shipping • Non-Inductive Design. tubes, 25 pieces per tube. Construction of MP900 and MP9000 Series: New The MP900 and MP9000 Series Kool-Pak® Power Power Resistor Film Resistors are constructed with Caddock's with Micronox® resistance film fired onto a flat ceramic Exposed Ceramic substrate. The terminal attachment and resistance Heat Dissipating element geometry are configured to provide Mounting outstanding non-inductive performance. The Surface. ceramic substrate is positioned in the molded package such that the resistor element and terminal attachment areas on the substrate are encapsulated in the molded body with the other side of the ceramic being exposed flush with the back mounting surface of the device. This construction is covered by one or more issued patents, also patents pending. Sales and Applications Engineering ELECTRONICS, INC. 17271 North Umpqua Hwy. Roseburg, Oregon 97470-9422 e-mail: caddock@caddock.com • web: www.caddock.com Phone: (541) 496-0700 For Caddock Distributors listed by country see caddock.com/contact/dist.html Fax: (541) 496-0408 © 2003-2017 Caddock Electronics, Inc. 28_IL134.0517

Page 2 of 2 MNood.el Package MRine.sistancMeax. RPoatwinegr VoMlataxg.e TFhilemrm (Ja)lR tRθoJe CCs aisstea n(Cc)e MaxT . M T A e X mp. Dimensions Comments MP915 TO-126 Style 0.020 Ω 1.00 K 15 Watts* 200 8.33°C/Watt 150°C Figure 1 Ceramic mounting surface MP916 TO-220 Style 0.010 Ω 0.019 Ω 16 Watts* PLiomwiteerd 7.81°C/Watt 150°C Figure 2 Ceramic mounting surface MP925 TO-220 Style 5.00K 100 K 25 Watts* 500 5.00°C/Watt 150°C Figure 2 Ceramic mounting surface MP930 TO-220 Style 0.020 Ω 4.99 K 30 Watts* 250 4.17°C/Watt 150°C Figure 2 Ceramic mounting surface MP9100 TO-247 Style 0.050 Ω 100 Ω 100 Watts* PLiomwiteerd 1.50°C/Watt 175°C Figure 3 Ceramic mounting surface Derating Curve Specifications: 100 % 80 * Derating Using Case Temperature (TC): Temperature Coefficient for MP915, MP916, G, WER RATIN 4600 AbTahll sepe ocdaw usepero tanen mcdap aseesrsa toetucmrieap teiesrd am touevraees ruluosraeinddg r atahtt eitnh dgees c raaertnient egdr e coruaf rttvehede. MTCP 9re2f5e,r eanncde Md Pto9 +3205:°C, ∆R taken at +150°C PO 20 A B ceramic mounting surface, with the part properly 0.50 ohms and above, -20 to +80 ppm/°C mounted and under electrical load. Without a heat sink, 0.050 ohm to 0.49 ohms, 0 to +200 ppm/°C 0 25 100 150 175 when in free air at +25°C, the MP915 is rated for 1.25 0.020 ohm to 0.049 ohm, 0 to +300 ppm/°C CASE TEMPERATURE, °C watts, the MP916, MP925, MP930 are rated for 2.25 0.010 ohm to 0.019 ohm, 0 to +500 ppm/°C watts, and the MP9100 is rated for 3.5 watts. A - MP915, MP916, MP925, MP930 Max. Temperature, TMax = 150°C B - MP9100 Max. Temperature, TMax = 175°C Temperature Coefficient for MP9100: TC referenced to +25°C, ∆R taken at +175°C The thermal design should satisfy the following equation: Copaesrea tTinegm tpeemrapteurraet u(Trec )r a+n g[Teh oefr mthael aRpepsliicsatatinocne. (RθJC) x power applied (Watts)] ≤ TMAX considering the full 0.50 ohms and above, -20 to +80 ppm/°C 0.050 ohm to 0.49 ohms, 0 to +150 ppm/°C Mounting Note: Mount on a smooth, clean, and flat heat sink surface with a thermal interface material, such as thermal grease. The entire exposed ceramic portion must be in thermal contact with the heat sink. When Operating Temperature: -55°C to TMAX screw mounting, use a compression washer which provides a mounting force of 150 to 300 pounds (665 to 1330 N). This will provide sufficient pressure on the package over time and through large temperature varia- Inductance: MP915, MP916, MP925, and MP930 tions to maintain the maximum power dissipation capability. Mounting torque to avoid package damage is 8 10nH typical; MP9100, 20nH typical, in series when in-lbs. (0.90 N-m). If a spring clip is used, a clip force of 8 to 30 pounds (35 to 130 N) is recommended to be applied to the center of the package. The clip should be round or smooth in the contact area to avoid concen- measured at a point 0.2 inches from the resistor trating the load on a small point of the plastic body of the package. Another mounting option is to use a body. pressure bar method which can achieve a greater mounting force with a greater contact area. For additional applications information regarding mounting and pulse handling see the Caddock DWV: The dielectric strength rating of 1500 VrmsAC Applications Notes at caddock.com or contact Applications Engineering. is based upon connections made between terminals shorted, and the metal surface the part is .(029.349 ± ±.0.1004) DIA. (.382.102 ± ±.0.2160) .(121.709 ± ±.0.2160) mounted to or a metal clip in contact with the top CL surface of the part. + .440 ±.010 Insulation Resistance: 10,000 Megohms min. Figure 1 .(028.003 ± ±.0.5210) M0.P1901Ω5 .(121.952 ± ±.0.2160) (11.18 ±.26) The resistor element is electrically isolated from TO-126 Style 1% the mounting surface. .053 ± .007 MP915 ( 1 .14.5403 ±±.10.5207) .(013.305 ± ±.0 .0148) Load Stability: 2,000 hours at rated power. (.76 ± .10) ∆R ±(1.0 percent + 0.0005 ohm) max. Power .025 ± .004 (.64 ±.10) rating dependent upon case temperature. See .200 ±.010 (5.08 ±.26) .058 ±.007 (1.47 ±.18) derating curve. .125 ±.004 .410 ±.010 .125 ±.010 (3.18 ±.10) DIA. (10.41 ±.26) (3.18 ±.26) Momentary Overload: 1.5 times rated power with CL applied voltage not to exceed 1.5 times maximum continuous operating voltage for 5 seconds. ∆R FTOig-u2r2e0 2 S tyle MP930 ( 3.1.1285 ±±..2061)0 ( 1 .66.4206 ±±..02160) ±(0.5 percent + 0.0005 ohm) max. .130 ±.030 10.0 MP916, MP925 (3.30 ±.76) 1% Moisture Resistance: Mil-Std-202, Method 106. and MP930 .053 ± .007 ∆R ±(0.5 percent + 0.0005 ohm) max. (1.35 ± .18) (1 2.5.7000 ±±1.0.2570) .(0.7360 ±± ..01004) T∆hRe ±rm(0a.5l Spehroccekn:t +M 0il-.S00td0-52 0o2h, mM)e tmhoadx .107, Cond. F. .200 ±.010 .025 ± .004 (.64 ±.10) (5.08 ±.26) .070 ±.010 (1.78 ±.26) Shock: 100G, Mil-Std-202, Method 213, Cond. I. ∆R ±(0.4 percent + 0.0005 ohm) max. 0.620 ± 0.010 0.195 ± 0.010 (30..6134 3± ±0 .01.00)0 4Dia. (15.75C L± 0.26) (4.95 ± 0.26) Vibration, High Frequency: Mil-Std-202, Method 0.210 ± 0.010 204, Cond. D. ∆R ±(0.4 percent + 0.0005 ohm) (5.33 ± 0.26) max. Figure 3 0.815 ± 0.010 TO-247 Style MP 9100 (20.70 ± 0.26) Terminal Strength: Mil-Std-202, Method 211, 0.110 ± 0.030 50.0 Cond. A (Pull Test) 5 lbs. ∆R ±(0.2 percent MP9100 (2.79 ± 0.76) 1% + 0.0005 ohm) max. 0.143 ± 0.007 0.570 ± 0.050 (3.63 ± 0.18) Terminal Material: Solderable (14.48 ± 1.27) 0.060 ± 0.004 (1.52 ± 0.10) Measurement Note: For these specifications, 0.400 ± 0.010 0(.003.821 + +00.0.1004 // --00..2061)0 resistance measurement shall be made at a point DIMENSIONS IN INCHES AND (MILLIMETERS) (10.16 ± 0.26) 0(2.0.4915 ±± 00..2061)0 0.2 inch (5.08 mm) from the resistor body. Sales and Applications Engineering ELECTRONICS, INC. 17271 North Umpqua Hwy. Roseburg, Oregon 97470-9422 e-mail: caddock@caddock.com • web: www.caddock.com Phone: (541) 496-0700 For Caddock Distributors listed by country see caddock.com/contact/dist.html Fax: (541) 496-0408 © 2003-2017 Caddock Electronics, Inc. 28_IL134.0517