I N D U C T O R S September 2014 Inductors for Standard Circuits Multilayer Ferrite MLF series MLF1005 1005 [0402 inch]* MLF1608 1608 [0603 inch] MLF2012 2012 [0805 inch] * Dimensions Code JIS[EIA]

(2/21) I N D U C T O R S REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150°C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/Aviation equipment (8) Public information-processing equipment (2) Transportation equipment (cars, electric trains, ships, etc.) (9) Military equipment (3) Medical equipment (10) Electric heating apparatus, burning equipment (4) Power-generation control equipment (11) Disaster prevention/crime prevention equipment (5) Atomic energy-related equipment (12) Safety equipment (6) Seabed equipment (13) Other applications that are not considered general-purpose (7) Transportation control equipment applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. 20140903 / inductor_commercial_standard_mlf_en.fm

(3/21) I N D U C T O R S Inductors for Standard Circuits Product compatible with RoHS directive Halogen-free Multilayer Ferrite Compatible with lead-free solders Overview of the MLF Series FEATURES The lineup includes a wide inductance range. Highly reliable monolithic structure with multilayer integration. APPLICATION Smart phones, tablet terminals, tuners, LCD-TVs, PDP-TVs, audio equipment, computers, signal processing for modules etc. PART NUMBER CONSTRUCTION MLF 1005 A R10 △ T 000 L×W×H Dimensions Inductance Inductance Series name characteristics Packaging style Internal code (mm) (µH) tolerance 1005 1.0×0.5×0.5 A 0.010 J ±5% T Taping 000 10N 1608 1.6×0.8×0.8 C (10nH) K ±10% A00 2.0×1.25×0.85 D R10 0.1 M ±20% D00 2012 2.0×1.25×1.25 E 1R0 1 G 100 10 K V OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Temperature range Operating Storage Package quantity Individual weight Type temperature temperature （°C） （°C） (pieces/reel) （mg） MLF1005 –55 to +125 –55 to +125 10,000 1.2 MLF1608 –55 to +125 –55 to +125 4,000 4 t=0.85 4,000 10 MLF2012 –55 to +125 –55 to +125 t=1.25 2,000 14 In case the product's inductance is 15µH or higher, both Operating and Storage temperature ranges are –40 to +85°C. The Storage temperature range is for after the circuit board is mounted. RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://product.tdk.com/en/environment/rohs/ Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm. (cid:129) All specifications are subject to change without notice. 20140903 / inductor_commercial_standard_mlf_en.fm

(4/21) I N D U C T O R S Overview of the MLF Series RECOMMENDED REFLOW PROFILE Preheating Soldering Natural cooling Peak T4 e ur T3 T3 at er p m e T T2 T: t3 T1 t1 t2 t: Time Preheating Soldering Peak Temp. Time Temp. Time Temp. Time T1 T2 t1 T3 t2 T4 t3 150°C 180°C 60 to 120s 230°C 30 to 60s 250 to 260°C 10s max. (cid:129) All specifications are subject to change without notice. 20140903 / inductor_commercial_standard_mlf_en.fm

(5/21) I N D U C T O R S MLF series MLF1005 Type SHAPE & DIMENSIONS 5 0 0. ± 0 5 0. 0.10min. 0.10min. 1.00±0.05 5 0 0. ± 0 5 0. Dimensions in mm RECOMMENDED LAND PATTERN 5 0. 0.5 0.4 0.5 Dimensions in mm (cid:129) All specifications are subject to change without notice. 20140903 / inductor_commercial_standard_mlf_en.fm

(6/21) I N D U C T O R S MLF MLF1005 Type series　 ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE L, Q measuring Self-resonant DC resistance Rated current L Q conditions frequency(MHz) (Ω) (mA) Part No. Frequency Current (µH) Tolerance min. typ. min. typ. max. typ. max. (MHz) (mA) 0.10 ±5%±10% 10 30 25 1.0 450 880 0.51 0.33 180 MLF1005VR10△T000 0.12 ±5%±10% 10 30 25 1.0 400 800 0.59 0.33 180 MLF1005VR12△T000 0.15 ±5%±10% 15 30 25 1.0 350 650 0.63 0.39 180 MLF1005VR15△T000 0.18 ±5%±10% 15 30 25 1.0 320 600 0.72 0.40 160 MLF1005VR18△T000 0.22 ±5%±10% 15 30 25 1.0 290 450 0.79 0.47 160 MLF1005VR22△T000 0.27 ±5%±10% 15 30 25 1.0 260 450 0.91 0.65 150 MLF1005VR27△T000 0.33 ±5%±10% 15 30 25 1.0 230 380 1.05 0.80 140 MLF1005VR33△T000 0.39 ±5%±10% 15 30 25 1.0 210 330 1.35 0.89 130 MLF1005VR39△T000 0.47 ±5%±10% 15 30 25 1.0 190 300 1.50 0.95 120 MLF1005VR47△T000 0.56 ±5%±10% 15 30 25 1.0 170 250 1.95 1.35 120 MLF1005VR56△T000 0.39 ±5%±10% 30 50 10 1.0 210 600 0.41 0.24 50 MLF1005GR39△T000 0.47 ±5%±10% 30 55 10 1.0 190 460 0.42 0.25 50 MLF1005GR47△T000 0.56 ±5%±10% 30 55 10 1.0 170 450 0.47 0.34 45 MLF1005GR56△T000 0.68 ±5%±10% 30 55 10 1.0 150 360 0.55 0.43 45 MLF1005GR68△T000 0.82 ±5%±10% 30 60 10 1.0 130 320 0.59 0.43 40 MLF1005GR82△T000 1.0 ±5%±10% 30 60 10 1.0 120 290 0.64 0.45 40 MLF1005G1R0△T000 1.2 ±5%±10% 30 60 10 1.0 110 230 0.79 0.55 35 MLF1005G1R2△T000 1.5 ±5%±10% 30 60 10 1.0 100 200 0.95 0.68 35 MLF1005G1R5△T000 1.8 ±5%±10% 30 60 10 1.0 90 180 1.05 0.75 30 MLF1005G1R8△T000 2.2 ±5%±10% 30 60 10 1.0 80 150 1.30 0.99 30 MLF1005G2R2△T000 The " △ " of the Part Number contains the inductance tolerance code, J (±5%) or K (±10%). ○Measurement equipment Measurement item Product No. Manufacturer L, Q 4294A+16034G Agilent Technologies Self-resonant frequency E4991A Agilent Technologies DC resistance Type-7561 Yokogawa ＊ Equivalent measurement equipment may be used. (cid:129) All specifications are subject to change without notice. 20140903 / inductor_commercial_standard_mlf_en.fm

(7/21) I N D U C T O R S MLF MLF1005 Type series　 ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH 10 G1R8 G1R2 GR39 1 GR82 )H GR56 µ (e VR33 c n a ct VR22 u d n I 0.1 VR15 VR10 VR47 0.01 1 10 100 1000 Frequency(MHz) 10 G2R2 G1R5 GR47 G1R0 1 )H GR68 µ VR39 (e c n cta VR27 du VR18 n I 0.1 VR12 VR56 0.01 1 10 100 1000 Frequency(MHz) ○Measurement equipment Product No. Manufacturer E4991A+16192A Agilent Technologies ＊ Equivalent measurement equipment may be used. (cid:129) All specifications are subject to change without notice. 20140903 / inductor_commercial_standard_mlf_en.fm

(8/21) I N D U C T O R S MLF MLF1005 Type series　 ELECTRICAL CHARACTERISTICS Q FREQUENCY CHARACTERISTICS GRAPH 70 60 GR39 G1R2 VR10 50 VR22 GR56 GR82 G1R8 VR47 40 Q VR33 VR15 30 20 10 0 1 10 100 1000 Frequency(MHz) 70 G1R0 60 50 VR27 VR39 GR68 VR56 40 GR47 VR12 Q VR18 G1R5 30 G2R2 20 10 0 1 10 100 1000 Frequency(MHz) ○Measurement equipment Product No. Manufacturer E4991A+16192A Agilent Technologies ＊ Equivalent measurement equipment may be used. (cid:129) All specifications are subject to change without notice. 20140903 / inductor_commercial_standard_mlf_en.fm

(9/21) I N D U C T O R S MLF series MLF1608 Type SHAPE & DIMENSIONS 5 1 0. ± 0 8 0. 0.30±0.20 0.30±0.20 1.60±0.15 5 1 0. ± 0 8 0. Dimensions in mm RECOMMENDED LAND PATTERN 8 0. 0.6 0.8 0.6 Dimensions in mm (cid:129) All specifications are subject to change without notice. 20140903 / inductor_commercial_standard_mlf_en.fm

(10/21) I N D U C T O R S MLF MLF1608 Type series　 ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE L, Q measuring Self-resonant DC resistance Rated current L Q conditions frequency(MHz) (Ω) (mA) Part No. Frequency Current (µH) Tolerance min. typ. min. typ. max. typ. max. (MHz) (mA) 0.047 ±20% 10 20 50 1.0 600 900 0.20 0.10 200 MLF1608D47N△T□□□ 0.068 ±20% 10 20 50 1.0 550 700 0.30 0.15 200 MLF1608D68N△T□□□ 0.082 ±20% 10 20 50 1.0 500 650 0.30 0.15 200 MLF1608D82N△T□□□ 0.10 ±5%±10%±20% 15 25 25 1.0 450 600 0.35 0.20 200 MLF1608DR10△T□□□ 0.12 ±5%±10%±20% 15 25 25 1.0 400 550 0.40 0.20 200 MLF1608DR12△T□□□ 0.15 ±5%±10%±20% 15 25 25 1.0 350 500 0.45 0.25 200 MLF1608DR15△T□□□ 0.18 ±5%±10%±20% 15 25 25 1.0 320 450 0.50 0.25 150 MLF1608DR18△T□□□ 0.22 ±5%±10%±20% 15 25 25 1.0 290 400 0.55 0.30 150 MLF1608DR22△T□□□ 0.27 ±5%±10%±20% 15 25 25 1.0 260 350 0.60 0.35 150 MLF1608DR27△T□□□ 0.33 ±5%±10%±20% 15 25 25 1.0 230 320 0.75 0.40 100 MLF1608DR33△T□□□ 0.39 ±5%±10%±20% 15 25 25 1.0 210 290 0.85 0.45 100 MLF1608DR39△T□□□ 0.47 ±5%±10%±20% 15 30 25 1.0 190 260 0.95 0.50 100 MLF1608DR47△T□□□ 0.56 ±5%±10%±20% 15 30 25 1.0 170 230 1.05 0.55 100 MLF1608DR56△T□□□ 0.68 ±5%±10%±20% 15 30 25 1.0 150 210 1.25 0.65 70 MLF1608DR68△T□□□ 0.82 ±5%±10%±20% 15 30 25 1.0 130 190 1.40 0.75 70 MLF1608DR82△T□□□ 1.0 ±5%±10%±20% 35 50 10 1.0 120 170 0.50 0.25 50 MLF1608A1R0△T□□□ 1.2 ±5%±10%±20% 35 50 10 1.0 110 150 0.65 0.25 50 MLF1608A1R2△T□□□ 1.5 ±5%±10%±20% 35 55 10 1.0 100 140 0.70 0.30 50 MLF1608A1R5△T□□□ 1.8 ±5%±10%±20% 35 55 10 1.0 90 130 0.85 0.35 50 MLF1608A1R8△T□□□ 2.2 ±5%±10%±20% 35 55 10 1.0 80 120 1.00 0.45 30 MLF1608A2R2△T□□□ 2.7 ±5%±10%±20% 35 55 10 1.0 70 110 1.15 0.50 30 MLF1608A2R7△T□□□ 3.3 ±5%±10%±20% 35 60 10 1.0 65 100 1.30 0.55 30 MLF1608A3R3△T□□□ 3.9 ±5%±10%±20% 35 60 10 1.0 60 90 1.45 0.65 30 MLF1608A3R9△T□□□ 4.7 ±5%±10%±20% 35 60 10 1.0 55 80 1.60 0.75 30 MLF1608A4R7△T□□□ 5.6 ±5%±10%±20% 35 60 4 0.1 45 70 1.10 0.55 15 MLF1608E5R6△T□□□ 6.8 ±5%±10%±20% 35 60 4 0.1 40 60 1.30 0.65 15 MLF1608E6R8△T□□□ 8.2 ±5%±10%±20% 35 60 4 0.1 35 55 1.50 0.80 10 MLF1608E8R2△T□□□ 10 ±5%±10%±20% 30 55 2 0.1 30 50 1.70 1.00 10 MLF1608E100△T□□□ 12 ±5%±10%±20% 30 55 2 0.1 25 45 1.80 1.20 10 MLF1608E120△T□□□ 15 ±10%±20% 20 40 1 0.1 22 42 1.50 0.80 2 MLF1608C150△T□□□ 18 ±10%±20% 20 40 1 0.1 20 40 1.60 0.85 2 MLF1608C180△T□□□ 22 ±10%±20% 20 40 1 0.1 18 38 1.70 0.90 2 MLF1608C220△T□□□ 27 ±10%±20% 20 40 1 0.1 15 35 1.80 1.20 2 MLF1608C270△T□□□ 33 ±10%±20% 20 40 1 0.1 10 30 2.20 1.40 2 MLF1608C330△T□□□  The " △ " of the Part Number contains the inductance tolerance code, J (±5%), K (±10%), or M (±20%).  The " □ " of the Part Number contains the internal code (000, A00, or D00), following below. (cid:129) In case the inductance tolerance code is J: 000 (cid:129) In case the inductance tolerance code is M or K (L = 0.047 to 8.2µH or 15 to 22µH): A00 (cid:129) In case the inductance tolerance code is M or K (L = 10,12,27,33µ): D00 ○Measurement equipment Measurement item Product No. Manufacturer L, Q 4294A+16034G Agilent Technologies Self-resonant frequency E4991A Agilent Technologies DC resistance Type-7561 Yokogawa ＊ Equivalent measurement equipment may be used. (cid:129) All specifications are subject to change without notice. 20140903 / inductor_commercial_standard_mlf_en.fm

(11/21) I N D U C T O R S MLF MLF1608 Type series　 ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH 100 E100 10 E6R8 A4R7 )H A3R3 DR68 µ A2R2 (nce 1 A1R0 A1R5 DR47 a ct DR33 u d n I DR22 DR15 0.1 DR10 0.01 1 10 100 1000 Frequency(MHz) 100 E120 10 E5R6 E8R2 A3R9 )H A2R7 µ DR82 (e A1R8 DR56 nc 1 A1R2 a ct DR39 u d n I DR27 DR18 0.1 DR12 0.01 1 10 100 1000 Frequency(MHz) ○Measurement equipment Product No. Manufacturer E4991A+16192A Agilent Technologies ＊ Equivalent measurement equipment may be used. (cid:129) All specifications are subject to change without notice. 20140903 / inductor_commercial_standard_mlf_en.fm

(12/21) I N D U C T O R S MLF MLF1608 Type series　 ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH 100 C330 C270 10 )H C220 µ (e c n a ct u nd C180 C150 I 1 0.1 0.1 1 10 100 Frequency(MHz) ○Measurement equipment Product No. Manufacturer 4294A+16034G Agilent Technologies ＊ Equivalent measurement equipment may be used. (cid:129) All specifications are subject to change without notice. 20140903 / inductor_commercial_standard_mlf_en.fm

(13/21) I N D U C T O R S MLF MLF1608 Type series　 ELECTRICAL CHARACTERISTICS Q FREQUENCY CHARACTERISTICS GRAPH 70 A3R3 60 A1R0 A1R5 A2R2 50 DR47 40 DR15 E100 E6R8 DR33 DR22 Q 30 DR10 20 DR68 10 0 1 10 100 1000 Frequency(MHz) 70 60 A3R9 A1R2 50 E8R2 E5R6 40 A1R8 DR12 Q E120 A2R7 30 DR82 DR56DR18 20 DR39 10 DR27 0 1 10 100 1000 Frequency(MHz) ○Measurement equipment Product No. Manufacturer E4991A+16192A Agilent Technologies ＊ Equivalent measurement equipment may be used. (cid:129) All specifications are subject to change without notice. 20140903 / inductor_commercial_standard_mlf_en.fm

(14/21) I N D U C T O R S MLF MLF1608 Type series　 ELECTRICAL CHARACTERISTICS Q FREQUENCY CHARACTERISTICS GRAPH 70 60 50 C150 C330 40 C270 Q 30 C180 C220 20 10 0 0.1 1 10 100 Frequency(MHz) ○Measurement equipment Product No. Manufacturer 4294A+16034G Agilent Technologies ＊ Equivalent measurement equipment may be used. (cid:129) All specifications are subject to change without notice. 20140903 / inductor_commercial_standard_mlf_en.fm

(15/21) I N D U C T O R S MLF series MLF2012 Type SHAPE & DIMENSIONS 0 2 0. ± 5 2 1. 0.50±0.30 0.50±0.30 2.00±0.20 T T 0.85±0.20 Dimensions in mm 1.25±0.20 RECOMMENDED LAND PATTERN 2 1. 0.8 1.0 0.8 Dimensions in mm (cid:129) All specifications are subject to change without notice. 20140903 / inductor_commercial_standard_mlf_en.fm

(16/21) I N D U C T O R S MLF MLF2012 Type series　 ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Self-resonant Rated L, Q measuring DC resistance L Q frequency current Thickness conditions (Ω) (MHz) (mA) T Part No. Frequency Current (mm) (µH) Tolerance min. typ. min. typ. max. typ. max. (MHz) (mA) 0.047 ±20% 15 25 50 1.0 550 700 0.10 0.05 300 0.85 MLF2012D47N△T000 0.068 ±20% 15 25 50 1.0 500 600 0.15 0.08 300 0.85 MLF2012D68N△T000 0.082 ±20% 15 25 50 1.0 450 550 0.15 0.08 300 0.85 MLF2012D82N△T000 0.10 ±5%±10%±20% 20 30 25 1.0 400 500 0.10 0.10 300 0.85 MLF2012DR10△T000 0.12 ±5%±10%±20% 20 30 25 1.0 360 450 0.12 0.20 300 0.85 MLF2012DR12△T000 0.15 ±5%±10%±20% 20 30 25 1.0 320 410 0.13 0.20 300 0.85 MLF2012DR15△T000 0.18 ±5%±10%±20% 20 30 25 1.0 280 370 0.15 0.20 300 0.85 MLF2012DR18△T000 0.22 ±5%±10%±20% 20 30 25 1.0 250 330 0.16 0.30 250 0.85 MLF2012DR22△T000 0.27 ±5%±10%±20% 20 30 25 1.0 220 300 0.18 0.30 250 0.85 MLF2012DR27△T000 0.33 ±5%±10%±20% 20 30 25 1.0 200 270 0.23 0.40 250 0.85 MLF2012DR33△T000 0.39 ±5%±10%±20% 25 35 25 1.0 180 250 0.25 0.40 200 0.85 MLF2012DR39△T000 0.47 ±5%±10%±20% 25 35 25 1.0 160 230 0.25 0.50 200 1.25 MLF2012DR47△T000 0.56 ±5%±10%±20% 25 35 25 1.0 150 210 0.30 0.50 150 1.25 MLF2012DR56△T000 0.68 ±5%±10%±20% 25 35 25 1.0 140 190 0.35 0.60 150 1.25 MLF2012DR68△T000 0.82 ±5%±10%±20% 25 35 25 1.0 130 170 0.40 0.60 150 1.25 MLF2012DR82△T000 1.0 ±5%±10%±20% 45 55 10 1.0 120 160 0.15 0.30 80 0.85 MLF2012A1R0△T000 1.2 ±5%±10%±20% 45 55 10 1.0 110 150 0.15 0.30 80 0.85 MLF2012A1R2△T000 1.5 ±5%±10%±20% 45 60 10 1.0 100 140 0.18 0.40 80 0.85 MLF2012A1R5△T000 1.8 ±5%±10%±20% 45 60 10 1.0 90 130 0.20 0.40 80 0.85 MLF2012A1R8△T000 2.2 ±5%±10%±20% 45 60 10 1.0 80 120 0.22 0.50 50 0.85 MLF2012A2R2△T000 2.7 ±5%±10%±20% 45 70 10 1.0 70 100 0.25 0.50 50 1.25 MLF2012A2R7△T000 3.3 ±5%±10%±20% 45 70 10 1.0 60 90 0.28 0.60 50 1.25 MLF2012A3R3△T000 3.9 ±5%±10%±20% 45 70 10 1.0 55 80 0.30 0.60 30 1.25 MLF2012A3R9△T000 4.7 ±5%±10%±20% 45 70 10 1.0 50 70 0.35 0.70 30 1.25 MLF2012A4R7△T000 5.6 ±5%±10%±20% 50 75 4 0.1 45 65 0.60 0.30 15 1.25 MLF2012E5R6△T000 6.8 ±5%±10%±20% 50 75 4 0.1 40 60 0.65 0.32 15 1.25 MLF2012E6R8△T000 8.2 ±5%±10%±20% 50 75 4 0.1 35 55 0.70 0.35 15 1.25 MLF2012E8R2△T000 10 ±5%±10%±20% 50 75 2 0.1 30 50 0.80 0.40 15 1.25 MLF2012E100△T000 12 ±5%±10%±20% 50 75 2 0.1 25 45 0.90 0.50 15 1.25 MLF2012E120△T000 15 ±10%±20% 30 45 1 0.1 22 40 0.70 0.35 5 1.25 MLF2012C150△T000 18 ±10%±20% 30 45 1 0.1 20 38 0.80 0.38 5 1.25 MLF2012C180△T000 22 ±10%±20% 30 45 1 0.1 18 35 0.90 0.45 5 1.25 MLF2012C220△T000 27 ±10%±20% 30 45 1 0.1 17 33 1.00 0.50 5 1.25 MLF2012C270△T000 33 ±10%±20% 30 45 0.4 0.1 15 28 1.10 0.55 5 1.25 MLF2012C330△T000 39 ±10%±20% 35 55 2 0.1 13 23 2.40 1.30 4 1.25 MLF2012K390△T000 47 ±10%±20% 35 55 2 0.1 11 20 2.70 1.60 4 1.25 MLF2012K470△T000 56 ±10%±20% 35 55 2 0.1 10 18 2.80 1.80 4 1.25 MLF2012K560△T000 68 ±10%±20% 25 45 1 0.1 9 16 2.90 2.00 2 1.25 MLF2012C680△T000 82 ±10%±20% 25 45 1 0.1 8 14 3.00 2.40 2 1.25 MLF2012C820△T000 100 ±10%±20% 25 45 1 0.1 7 12 3.10 2.50 2 1.25 MLF2012C101△T000 The " △ " of the Part Number contains the inductance tolerance code, J (±5%), K (±10%), or M (±20%). ○Measurement equipment Measurement item Product No. Manufacturer L, Q 4294A+16034G Agilent Technologies Self-resonant frequency E4991A Agilent Technologies DC resistance Type-7561 Yokogawa ＊ Equivalent measurement equipment may be used. (cid:129) All specifications are subject to change without notice. 20140903 / inductor_commercial_standard_mlf_en.fm

(17/21) I N D U C T O R S MLF MLF2012 Type series　 ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH 100 E100 10 E6R8 A4R7 )H A3R3 DR68 µ A2R2 (nce 1 A1R0 A1R5 DR47 a ct DR33 u d n I DR22 DR15 0.1 DR10 0.01 1 10 100 1000 Frequency(MHz) 100 E120 10 E8R2 E5R6 A3R9 DR82 )H A2R7 µ DR56 (e A1R8 nc 1 A1R2 a DR39 ct du DR27 n I DR18 0.1 DR12 0.01 1 10 100 1000 Frequency(MHz) ○Measurement equipment Product No. Manufacturer E4991A+16192A Agilent Technologies ＊ Equivalent measurement equipment may be used. (cid:129) All specifications are subject to change without notice. 20140903 / inductor_commercial_standard_mlf_en.fm

(18/21) I N D U C T O R S MLF MLF2012 Type series　 ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH 100 C101 C680 C820 K560 10 K470 )H K390 µ (ce C270 an C220 ct C330 u d n C150 I 1 C180 0.1 0.1 1 10 100 Frequency(MHz) ○Measurement equipment Product No. Manufacturer 4294A+16034G Agilent Technologies ＊ Equivalent measurement equipment may be used. (cid:129) All specifications are subject to change without notice. 20140903 / inductor_commercial_standard_mlf_en.fm

(19/21) I N D U C T O R S MLF MLF2012 Type series　 ELECTRICAL CHARACTERISTICS Q FREQUENCY CHARACTERISTICS GRAPH 90 80 A4R7 A3R3 70 A2R2 E100 DR22 A1R5 60 DR15 E6R8 DR33 50 Q A1R0 40 DR47 DR10 30 DR68 20 10 0 1 10 100 1000 Frequency(MHz) 90 80 E5R6 E8R2 A2R7 A3R9 70 E120 60 DR18 A1R8 DR39 50 Q A1R2 DR12 40 DR82 30 DR56 20 DR27 10 0 1 10 100 1000 Frequency(MHz) ○Measurement equipment Product No. Manufacturer E4991A+16192A Agilent Technologies ＊ Equivalent measurement equipment may be used. (cid:129) All specifications are subject to change without notice. 20140903 / inductor_commercial_standard_mlf_en.fm

(20/21) I N D U C T O R S MLF MLF2012 Type series　 Q FREQUENCY CHARACTERISTICS GRAPH 90 80 70 K470 60 C270 C330 50 C180 Q K560 K390 40 C101 C220 30 C680 20 C820 C150 10 0 0.1 1 10 100 Frequency(MHz) ○Measurement equipment Product No. Manufacturer 4294A+16034G Agilent Technologies ＊ Equivalent measurement equipment may be used. (cid:129) All specifications are subject to change without notice. 20140903 / inductor_commercial_standard_mlf_en.fm

(21/21) I N D U C T O R S MLF series Packaging Style REEL DIMENSIONS 1.0 n. mi 0 6 ø 2.0±0.5 8.4+–02..00 ø13±0.2 14.4max. ø21±0.8 ø180±2.0 Dimensions in mm TAPE DIMENSIONS 1 5 Type A B K Sprocket hole 1.5+–00..01 Cavity ±1.750.±3.50.0 MMLLFF11060058 11.1.95±±00..21 01..615±±00..21 01..81 mmaaxx.. t=0.85 2.3±0.2 1.5±0.2 1.1 max. MLF2012 t=1.25 2.3±0.2 1.5±0.2 1.5 max. 3 0. ± 0 8. A K B 4.0±0.1 2.0±0.05 2.0±0.05 160min. Taping 200min. Drawing direction 300min. Dimensions in mm (cid:129) All specifications are subject to change without notice. 20140903 / inductor_commercial_standard_mlf_en.fm

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: T DK: MLF1005DR27KT MLF1005AR56KT MLF1005AR82KT MLF1005A1R0KT MLF1005DR10KT MLF1005A2R2KT MLF1005DR12KT MLF1005AR39KT MLF1005DR18KT MLF1005AR47KT MLF1005DR33KT MLF1005LR10K MLF1005LR12K MLF1005LR15K MLF1005LR18K MLF1005LR22K MLF1005LR27K MLF1005LR33K MLF1005LR39K MLF1005LR47K MLF1005LR56K MLF1005LR68K MLF1005LR82K MLF1005L1R0K MLF1005L1R2K MLF1005L1R5K MLF1005L1R8K MLF1005L2R2K MLF1005VR47J MLF1005VR15J MLF1005VR27J MLF1005VR18J MLF1005VR22J MLF1005VR39J MLF1005VR33J MLF1005VR56J MLF1005G1R2JT MLF1005VR10JT MLF1005GR39JT MLF1005G1R0JT MLF1005GR47JT MLF1005G1R8JT MLF1005G1R5JT MLF1005G2R2JT MLF1005GR56JT MLF1005GR68JT MLF1005VR12JT MLF1005GR82JT MLF1005VR39KT MLF1005VR47KT MLF1005VR10KT MLF1005G1R8KT MLF1005VR15KT MLF1005GR56KT MLF1005VR22KT MLF1005GR47KT MLF1005G1R0KT MLF1005VR33KT MLF1005VR12KT MLF1005VR18KT MLF1005VR27KT MLF1005G1R2KT MLF1005GR68KT MLF1005GR82KT MLF1005G2R2KT MLF1005G1R5KT MLF1005VR56KT MLF1005GR39KT000 MLF1005AR68KT MLF1005A1R5KT MLF1005VR39JT000 MLF1005VR22JT000 MLF1005VR56JT000 MLF1005G1R5KT000 MLF1005G2R2JT000 MLF1005GR56KT000 MLF1005GR82JT000 MLF1005G1R0KT000 MLF1005VR18KT000 MLF1005GR56JT000 MLF1005VR10KT000 MLF1005GR68KT000 MLF1005G1R8KT000 MLF1005G1R2KT000 MLF1005VR12KT000 MLF1005VR47KT000 MLF1005G1R8JT000 MLF1005VR27KT000 MLF1005VR15JT000 MLF1005VR47JT000 MLF1005GR82KT000 MLF1005VR22KT000 MLF1005GR47JT000 MLF1005VR12JT000 MLF1005VR39KT000 MLF1005GR68JT000 MLF1005VR27JT000 MLF1005GR39JT000 MLF1005VR18JT000 MLF1005GR47KT000