® ® Solutions Seeking Problems. MAGNASPHERE S-Series This series is used in the security industry for door and window sensors in Open Loop alarm systems. It has a wider actuation zone in the X or Y axis that other Form B Magnasphere switches. Robust all metal construction is highly resistant to magnetic tamper and defeat, and permanent contact welding from power surges. CONTACT CHARACTERISTICS Contact Form: B (Normally Closed-N.C.) Contact Material: Gold/Gold .095” X & Y Axis Mode Initial Contact Resistance (Typical): < 150 Milli Ohms Z Axis Mode Contact Capacitance: < 1 pf Contact Ratings: 30 VDC @ 250 ma Contact Bounce* (Typical): < 10 .021” milliseconds*. Recommended trial de-bounce - 15 milliseconds (min.) .453” ref .320” ref closed contact condition for logic state .020” changes - or 30 Hz low pass filter buffer Minimum Breakdown Voltage (Typical): 300 VDC Insulation Resistance (Typical): > 5 Mega Ohms .200” dia ref .205” ref OPERATION CHARACTERISTICS .120” ref .143” dia ref Operate/Release Values: See Switching Characteristics Table Actuation Magnet Orientation: Either Pole Maximum Operating Frequency: 20 Hz Mounting Position: Any Plane General Sense Zone SS--SSEERRIIEESS:: Operating Temperature: -40°C to +150°C MMGG--BB22--2200--SS Shock (Switch Damage): > 100 G’s Vibration: 10-15 G’s (80-450 Hz) (Higher Values Available) GENERAL CHARACTERISTICS & INFORMATION Construction: Non-Ferrous Metal Housing, life gain may be realized by center pin use the support of some type of parallel Compression Seal Hermetically Sealed, as cathode on logic loads, but center jaws spaced away from the glass seal to Protective Gas Atmosphere, Precious pin as anode on larger loads. grip the lead wirepins while bending the Metal Plated Spherical Magnet Contact. pins’ free ends, so no bending strains Lead Wire Cutting / Bending Guidelines: are imposed on the glass seal. Soldering Guidelines: 600º F (315º C) Cut length has no effect on magnetic Temperature iron for 5 sec. (max.). Do OP/REL values. Shearing action type Other Comments: Ferromagnetic mate- not solder within 1/8” (3 mm) of glass cutters are recommended, but end nippers rials and strong Electromagnetic devices seal. Lead pins precious metal plated and side cutters are NOT recommended. proximate to the switch or its actuator for enhanced solderability. Metal style seals are extraordinarily magnet may adversely affect expected rugged, but the bending of unsupported OP/REL switching values. Experimen- Termination Polarity Guidelines: Polarity lead wire pins adjacent to the glass seal tation is recommended to investigate selection is non-critical, though some is not recommended (i.e. when bending areas of concern. Revised 3/30/2012 www.MAGNASPHERE.com

American-Made ® ® MAGNASPHERE® NEW MAGNASPHERE Switch Technology SWITCHING CHARACTERISTICS AIR GAP DISTANCE POSITION TYPICAL MIN MAX r o s n e N S E O netic MG-B2-20-S a (a) Leads Horz. “OPEN” .626” .197” 1.055” 0.5” L x 35 MAG Mag b d (b) Leads Horz. “CLOSED” .916” .541” 1.291” .375” T NET TA R e G v ET i t c e f f E d n a d 1 FE Most Advance MG-B2-20-S ba d ((ab)) LLeeaaddss HHoorrzz.. ““OCLPOESNE”D” NOT RECOMMENDED .0” L x 1.0” W x .0625” TEG. C1010 Low Carbon RROUS METAL TARGET e h T S-Series Switching characteristics the target moves closer (a), this normally closed switch will OPEN at the air gap distance (d), and CLOSE when the target moves away (b). ABOUT MAGNASPHERE PATENTED DESIGN INDUSTRY AWARDS MAGNASPHERE® Corp. is a privately held company MAGNASPHERE® products are covered Best of Show Award: founded in 2002, with the purpose of providing superior by one or more of the following U.S. and ISC Expo international patents: performing magnetic switch and sensor technology to Gold Award Sensor Technology: the industrial/commercial OEM and security markets. #5332992 #5530428 #5673021 Sensors Expo MAGNASPHERE’s patented, award-winning technology #5880659 #5977873 #6087936 Best Intrusion establishes new standards for magnetic switch perfor- #6506987 #6603378 #6803845 Detection: #7023308 (Patents Pending) ISC Expo mance while providing an affordable and more effective alternative to other magnetic switch technologies. MAGNASPHERE® NOTICE OF LIMITED LICENSE AND RIGHTS: (Security Applications) The purchase of MAGNASPHERE® switches provides the purchaser and the purchaser's Learn more: Visit us at www.MAGNASPHERE.com. customers with a limited right and license to make, use, offer for sale, and sell security devices, each making use of a single MAGNASPHERE® switch; however, this limited right and license does not extend to and specifically excludes security devices making use of Standard for Industrial Control Equipment, UL 508 two or more MAGNASPHERE® switches that cooperatively monitor a single area or location. MAGNASPHERE® Corp., 23777 Stone Ridge Drive, Suite 160, Waukesha, Wisconsin 53188. tel: 262.347.0711 fax: 262.347.0710 © 2012 MAGNASPHERE® CORP. All Rights Reserved.