MCP4017/18/19 2 7-Bit Single I C™ Digital POT with Volatile Memory in SC70 Package Types Features Potentiometer Rheostat • Potentiometer or Rheostat configuration options • 7-bit: Resistor Network Resolution MCP4018 MCP4017 SC70-6 - 127 Resistors (128 Steps) SC70-6 • Zero Scale to Full Scale Wiper operation VDD 1 A 6 A VDD 1 W 6 W A • RAB Resistances: 5kΩ, 10kΩ, 50kΩ, or 100kΩ VSS 2 B W 5 W VSS 2 B 5 B • Low Wiper Resistance: 100Ω (typical) SCL 3 4 SDA SCL 3 4 SDA • Low Tempco: MCP4019 - Absolute (Rheostat): 50ppm typical SC70-5 (0°C to 70°C) - Ratiometric (Potentiometer): 10ppm typical VDD 1 W 5 W • Simple I2C Protocol with read & write commands VSS 2 B A SCL 3 4 SDA • Brown-out reset protection (1.5V typical) • Power-on Default Wiper Setting (Mid-scale) • Wide Bandwidth (-3dB) Operation: • Low-Power Operation: - 2MHz (typical) for 5.0kΩ device - 2.5µA Static Current (typical) • Extended temperature range (-40°C to +125°C) • Wide Operating Voltage Range: • Very small package (SC70) - 2.7V to 5.5V - Device Characteristics • Lead free (Pb-free) package Specified - 1.8V to 5.5V - Device Operation Device Features s Resistance (typical) Device Control Interface # of Step ConWfigipuerar tion Memory Type Options (kΩ) W(iΩp)er ORpaVenrDgaDeti n(1g) Package MCP4017 I2C 128 Rheostat RAM 5.0, 10.0, 50.0, 100.0 75 1.8V to 5.5V SC70-6 MCP4018 I2C 128 Potentiometer RAM 5.0, 10.0, 50.0, 100.0 75 1.8V to 5.5V SC70-6 MCP4019 I2C 128 Rheostat RAM 5.0, 10.0, 50.0, 100.0 75 1.8V to 5.5V SC70-5 Note1: Analog characteristics only tested from 2.7V to 5.5V © 2009 Microchip Technology Inc. DS22147A-page 1

MCP4017/18/19 Device Block Diagram VDD Power-up/ A (2) Brown-out V SS Control W I2C Serial SCL Interface Resistor SDA Module, Network 0 B (1, 2) Control (Pot 0) Logic, & Note 1: Some configurations will have this Memory signal internally connected to ground. Note 1 2: In some configurations, this signal may not be connected externally (internally floating or grounded). Comparison of Similar Microchip Devices (1) Device Control Interface # of Steps ConWfigipuerar tion Memory Type ResOisptatinocnes ((tkyΩpi)cal) ORpaeVnrgDaDeti n(2g) HV Interface WiperLock Technology Package MCP4017 I2C 128 Rheostat RAM 5.0, 10.0, 50.0, 100.0 1.8V to 5.5V No No SC70-6 MCP4012 U/D 64 Rheostat RAM 2.1, 5.0, 10.0, 50.0 1.8V to 5.5V Yes No SOT-23-6 MCP4022 U/D 64 Rheostat EE 2.1, 5.0, 10.0, 50.0 2.7V to 5.5V Yes Yes SOT-23-6 MCP4132 SPI 129 Rheostat RAM 5.0, 10.0, 50.0, 100.0 1.8V to 5.5V Yes No PDIP-8, MCP4142 SPI 129 Rheostat EE 5.0, 10.0, 50.0, 100.0 2.7V to 5.5V Yes Yes SOIC-8, MSOP-8, MCP4152 SPI 257 Rheostat RAM 5.0, 10.0, 50.0, 100.0 1.8V to 5.5V Yes No DFN-8 MCP4162 SPI 257 Rheostat EE 5.0, 10.0, 50.0, 100.0 2.7V to 5.5V Yes Yes MCP4532 I2C 129 Rheostat RAM 5.0, 10.0, 50.0, 100.0 1.8V to 5.5V Yes No MSOP-8, MCP4542 I2C 129 Rheostat EE 5.0, 10.0, 50.0, 100.0 2.7V to 5.5V Yes Yes DFN-8 MCP4552 I2C 257 Rheostat RAM 5.0, 10.0, 50.0, 100.0 1.8V to 5.5V Yes No MCP4562 I2C 257 Rheostat EE 5.0, 10.0, 50.0, 100.0 2.7V to 5.5V Yes Yes MCP4018 I2C 128 Potentiometer RAM 5.0, 10.0, 50.0, 100.0 1.8V to 5.5V No No SC70-6 MCP4013 U/D 64 Potentiometer RAM 2.1, 5.0, 10.0, 50.0 1.8V to 5.5V Yes No SOT-23-6 MCP4023 U/D 64 Potentiometer EE 2.1, 5.0, 10.0, 50.0 2.7V to 5.5V Yes Yes SOT-23-6 MCP4019 I2C 128 Rheostat RAM 5.0, 10.0, 50.0, 100.0 1.8V to 5.5V No No SC70-5 MCP4014 U/D 64 Rheostat RAM 2.1, 5.0, 10.0, 50.0 1.8V to 5.5V Yes No SOT-23-5 MCP4024 U/D 64 Rheostat EE 2.1, 5.0, 10.0, 50.0 2.7V to 5.5V Yes Yes SOT-23-5 Note 1: This table is broken into three groups by a thick line (and color coding). The unshaded devices in this table are the devices described in this data sheet, while the shaded devices offer a comparable resistor network configuration. 2: Analog characteristics only tested from 2.7V to 5.5V DS22147A-page 2 © 2009 Microchip Technology Inc.

MCP4017/18/19 1.0 ELECTRICAL † Notice: Stresses above those listed under “Maximum CHARACTERISTICS Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those Absolute Maximum Ratings † indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions Voltage on V with respect to V ..... -0.6V to +7.0V DD SS for extended periods may affect device reliability. Voltage on SCL, and SDA with respect to V SS -0.6V to 12.5V ............................................................................. Voltage on all other pins (A, W, and B) with respect to V -0.3V to V + 0.3V SS............................ DD Input clamp current, I IK (VI < 0, VI > VDD, VI > VPP ON HV pins)...........±20mA Output clamp current, I OK (V < 0 or V > V ).......................................±20mA O O DD Maximum output current sunk by any Output pin ...........................................................................25mA Maximum output current sourced by any Output pin ...........................................................................25mA Maximum current out of V pin......................100mA SS Maximum current into V pin.........................100mA DD Maximum current into A, W and B pins...........±2.5mA Package power dissipation (T = +50°C, T = +150°C) A J SC70-5............................................................302mW SC70-6..................................................................TBD Storage temperature..........................-65°C to +150°C Ambient temperature with power applied ...........................................................-40°C to +125°C ESD protection on all pins ........................≥ 4kV (HBM) ........................................................................≥ 400V (MM) Maximum Junction Temperature (T ) ..............+150°C J © 2009 Microchip Technology Inc. DS22147A-page 3

MCP4017/18/19 AC/DC CHARACTERISTICS Standard Operating Conditions (unless otherwise specified) Operating Temperature –40°C ≤ T ≤ +125°C (extended) A DC Characteristics All parameters apply across the specified operating ranges unless noted. V = +2.7V to 5.5V, 5kΩ, 10kΩ, 50kΩ, 100kΩ devices. DD Typical specifications represent values for V = 5.5V, T = +25°C. DD A Parameters Sym Min Typ Max Units Conditions Supply Voltage V 2.7 — 5.5 V Analog Characteristics specified DD 1.8 — 5.5 V Digital Characteristics specified V Start Voltage V — — 1.65 V RAM retention voltage (V ) < V DD BOR RAM BOR to ensure Wiper Reset V Rise Rate to V (Note7) V/ms DD DDRR ensure Power-on Reset Delay after device T — 10 20 µS BORD exits the reset state (V > V ) DD BOR Supply Current I — 45 80 µA Serial Interface Active, DD (Note8) Write all 0’s to Volatile Wiper V = 5.5V, F = 400kHz DD SCL — 2.5 5 µA Serial Interface Inactive, (Stop condition, SCL = SDA = V ), IH Wiper = 0, V = 5.5V DD Note 1: Resistance is defined as the resistance between terminal A to terminal B. 2: INL and DNL are measured at V with V = V and V = V . W A DD B SS 3: MCP4018 device only, includes V and V . WZSE WFSE 4: Resistor terminals A, W and B’s polarity with respect to each other is not restricted. 5: This specification by design. 6: Non-linearity is affected by wiper resistance (R ), which changes significantly over voltage and W temperature. 7: POR/BOR is not rate dependent. 8: Supply current is independent of current through the resistor network DS22147A-page 4 © 2009 Microchip Technology Inc.

MCP4017/18/19 AC/DC CHARACTERISTICS (CONTINUED) Standard Operating Conditions (unless otherwise specified) Operating Temperature –40°C ≤ T ≤ +125°C (extended) A DC Characteristics All parameters apply across the specified operating ranges unless noted. V = +2.7V to 5.5V, 5kΩ, 10kΩ, 50kΩ, 100kΩ devices. DD Typical specifications represent values for V = 5.5V, T = +25°C. DD A Parameters Sym Min Typ Max Units Conditions Resistance R 4.0 5 6.0 kΩ -502 devices (Note1) AB (± 20%) 8.0 10 12.0 kΩ -103 devices (Note1) 40.0 50 60.0 kΩ -503 devices (Note1) 80.0 100 120.0 kΩ -104 devices (Note1) Resolution N 128 Taps No Missing Codes Step Resistance R — R / — Ω Note5 S AB (127) Wiper Resistance R — 100 170 Ω V = 5.5 V, I = 2.0mA, code = 00h W DD W — 155 325 Ω V = 2.7 V, I = 2.0mA, code = 00h DD W Nominal ΔR /ΔT — 50 — ppm/°C T = -20°C to +70°C AB A Resistance — 100 — ppm/°C T = -40°C to +85°C A Tempco — 150 — ppm/°C T = -40°C to +125°C A Ratiometeric ΔV /ΔT — 15 — ppm/°C Code = Midscale (3Fh) WB Tempco Resistor Terminal V V V Vss — V V Note4, Note5 A, W, B DD Input Voltage Range (Terminals A, B and W) Maximum current I — — 2.5 mA Terminal A I , W = Full Scale (FS) T AW through Terminal — — 2.5 mA Terminal B I , W = Zero Scale (ZS) BW (A, W or B) — — 2.5 mA Terminal W I or I , W = FS or ZS Note5 AW BW — — 1.38 mA I , V = 0V, V = 5.5V, AB B A R = 4000 AB(MIN) — — 0.688 mA I , V = 0V, V = 5.5V, Terminal A AB B A R = 8000 and AB(MIN) — — 0.138 mA I , V = 0V, V = 5.5V, Terminal B AB B A R = 40000 AB(MIN) — — 0.069 mA I , V = 0V, V = 5.5V, AB B A R = 80000 AB(MIN) Note 1: Resistance is defined as the resistance between terminal A to terminal B. 2: INL and DNL are measured at V with V = V and V = V . W A DD B SS 3: MCP4018 device only, includes V and V . WZSE WFSE 4: Resistor terminals A, W and B’s polarity with respect to each other is not restricted. 5: This specification by design. 6: Non-linearity is affected by wiper resistance (R ), which changes significantly over voltage and W temperature. 7: POR/BOR is not rate dependent. 8: Supply current is independent of current through the resistor network © 2009 Microchip Technology Inc. DS22147A-page 5

MCP4017/18/19 AC/DC CHARACTERISTICS (CONTINUED) Standard Operating Conditions (unless otherwise specified) Operating Temperature –40°C ≤ T ≤ +125°C (extended) A DC Characteristics All parameters apply across the specified operating ranges unless noted. V = +2.7V to 5.5V, 5kΩ, 10kΩ, 50kΩ, 100kΩ devices. DD Typical specifications represent values for V = 5.5V, T = +25°C. DD A Parameters Sym Min Typ Max Units Conditions Full Scale Error V -3.0 -0.1 — LSb 5kΩ 2.7V ≤ V ≤ 5.5V WFSE DD (MCP4018 only) -2.0 -0.1 — LSb 10kΩ 2.7V ≤ V ≤ 5.5V DD (code = 7Fh) -0.5 -0.1 — LSb 50kΩ 2.7V ≤ V ≤ 5.5V DD -0.5 -0.1 — LSb 100kΩ 2.7V ≤ V ≤ 5.5V DD Zero Scale Error V — +0.1 +3.0 LSb 5kΩ 2.7V ≤ V ≤ 5.5V WZSE DD (MCP4018 only) — +0.1 +2.0 LSb 10kΩ 2.7V ≤ V ≤ 5.5V DD (code = 00h) — +0.1 +0.5 LSb 50kΩ 2.7V ≤ V ≤ 5.5V DD — +0.1 +0.5 LSb 100kΩ 2.7V ≤ V ≤ 5.5V DD Potentiometer INL -0.5 ±0.25 +0.5 LSb 2.7V ≤ V ≤ 5.5V DD Integral MCP4018 device only (Note2) Non-linearity Potentiometer DNL -0.25 ±0.125 +0.25 LSb 2.7V ≤ V ≤ 5.5V DD Differential Non- MCP4018 device only (Note2) linearity Bandwidth -3dB BW — 2 — MHz 5kΩ Code = 3Fh (See Figure2-83, — 1 — MHz 10kΩ Code = 3Fh load = 30pF) — 260 — kHz 50kΩ Code = 3Fh — 100 — kHz 100kΩ Code = 3Fh Note 1: Resistance is defined as the resistance between terminal A to terminal B. 2: INL and DNL are measured at V with V = V and V = V . W A DD B SS 3: MCP4018 device only, includes V and V . WZSE WFSE 4: Resistor terminals A, W and B’s polarity with respect to each other is not restricted. 5: This specification by design. 6: Non-linearity is affected by wiper resistance (R ), which changes significantly over voltage and W temperature. 7: POR/BOR is not rate dependent. 8: Supply current is independent of current through the resistor network DS22147A-page 6 © 2009 Microchip Technology Inc.

MCP4017/18/19 AC/DC CHARACTERISTICS (CONTINUED) Standard Operating Conditions (unless otherwise specified) Operating Temperature –40°C ≤ T ≤ +125°C (extended) A DC Characteristics All parameters apply across the specified operating ranges unless noted. V = +2.7V to 5.5V, 5kΩ, 10kΩ, 50kΩ, 100kΩ devices. DD Typical specifications represent values for V = 5.5V, T = +25°C. DD A Parameters Sym Min Typ Max Units Conditions Rheostat Integral R-INL -2.0 ±0.5 +2.0 LSb 5kΩ 5.5V, I = 900µA W Non-linearity -5.0 +3.5 +5.0 LSb 2.7V, I = 430µA (Note6) W MCP4018 See Section2.0 LSb 1.8V (Note6) (Note3) MCP4017 and -2.0 ±0.5 +2.0 LSb 10kΩ 5.5V, IW = 450µA MCP4019 devices -4.0 +2.5 +4.0 LSb 2.7V, I = 215µA (Note6) W only (Note3) See Section2.0 LSb 1.8V (Note6) -1.125 ±0.5 +1.125 LSb 50kΩ 5.5V, I = 90µA W -1.5 +1 +1.5 LSb 2.7V, I = 43µA (Note6) W See Section2.0 LSb 1.8V (Note6) -0.8 ±0.5 +0.8 LSb 100kΩ 5.5V, I = 45µA W -1.125 +0.25 +1.125 LSb 2.7V, I = 21.5µA (Note6) W See Section2.0 LSb 1.8V (Note6) Rheostat R-DNL -0.5 ±0.25 +0.5 LSb 5kΩ 5.5V, I = 900mA W Differential Non- -0.75 +0.5 +0.75 LSb 2.7V, I = 430µA (Note6) W linearity See Section2.0 LSb 1.8V (Note6) MCP4018 (Note3) -0.5 ±0.25 +0.5 LSb 10kΩ 5.5V, IW = 450µA MCP4017 and -0.75 +0.5 +0.75 LSb 2.7V, I = 215µA (Note6) W MCP4019 devices See Section2.0 LSb 1.8V (Note6) only (Note3) -0.375 ±0.25 +0.375 LSb 50kΩ 5.5V, I = 90µA W -0.375 ±0.25 +0.375 LSb 2.7V, I = 43µA (Note6) W See Section2.0 LSb 1.8V (Note6) -0.375 ±0.25 +0.375 LSb 100kΩ 5.5V, I = 45µA W -0.375 ±0.25 +0.375 LSb 2.7V, I = 21.5µA (Note6) W See Section2.0 LSb 1.8V (Note6) Capacitance (P ) C — 75 — pF f =1MHz, Code = Full Scale A AW Capacitance (P ) C — 120 — pF f =1MHz, Code = Full Scale w W Capacitance (P ) C — 75 — pF f =1MHz, Code = Full Scale B BW Note 1: Resistance is defined as the resistance between terminal A to terminal B. 2: INL and DNL are measured at V with V = V and V = V . W A DD B SS 3: MCP4018 device only, includes V and V . WZSE WFSE 4: Resistor terminals A, W and B’s polarity with respect to each other is not restricted. 5: This specification by design. 6: Non-linearity is affected by wiper resistance (R ), which changes significantly over voltage and W temperature. 7: POR/BOR is not rate dependent. 8: Supply current is independent of current through the resistor network © 2009 Microchip Technology Inc. DS22147A-page 7

MCP4017/18/19 AC/DC CHARACTERISTICS (CONTINUED) Standard Operating Conditions (unless otherwise specified) Operating Temperature –40°C ≤ T ≤ +125°C (extended) A DC Characteristics All parameters apply across the specified operating ranges unless noted. V = +2.7V to 5.5V, 5kΩ, 10kΩ, 50kΩ, 100kΩ devices. DD Typical specifications represent values for V = 5.5V, T = +25°C. DD A Parameters Sym Min Typ Max Units Conditions Digital Inputs/Outputs (SDA, SCK) Schmitt Trigger V 0.7V — — V 1.8V ≤ V ≤ 5.5V IH DD DD High Input Threshold Schmitt Trigger V -0.5 — 0.3V V IL DD Low Input Threshold Hysteresis of V — 0.1V — V All inputs except SDA and SCL HYS DD Schmitt Trigger N.A. — — V V < 2.0V DD Inputs (Note5) SDA 100kHz N.A. — — V V ≥ 2.0V DD and 0.1V — — V V < 2.0V DD SCL DD 400kHz 0.05V — — V V ≥ 2.0V DD DD Output Low V V — 0.2V V V < 2.0V, I = 1mA OL SS DD DD OL Voltage (SDA) V — 0.4 V V ≥ 2.0V, I = 3mA SS DD OL Input Leakage I -1 — 1 µA V = V and V = V IL IN DD IN SS Current Pin Capacitance C , C — 10 — pF f = 400kHz IN OUT C RAM (Wiper) Value Value Range N 0h — 7Fh hex Wiper POR/BOR N 3Fh hex POR/BOR Value Power Requirements Power Supply PSS — 0.0005 0.0035 %/% V = 2.7V to 5.5V, DD Sensitivity V = 2.7V, Code = 3Fh A (MCP4018 only) Note 1: Resistance is defined as the resistance between terminal A to terminal B. 2: INL and DNL are measured at V with V = V and V = V . W A DD B SS 3: MCP4018 device only, includes V and V . WZSE WFSE 4: Resistor terminals A, W and B’s polarity with respect to each other is not restricted. 5: This specification by design. 6: Non-linearity is affected by wiper resistance (R ), which changes significantly over voltage and W temperature. 7: POR/BOR is not rate dependent. 8: Supply current is independent of current through the resistor network DS22147A-page 8 © 2009 Microchip Technology Inc.

MCP4017/18/19 1.1 I2C Mode Timing Waveforms and Requirements SCL 91 93 90 92 SDA START STOP Condition Condition FIGURE 1-1: I2C Bus Start/Stop Bits Timing Waveforms. TABLE 1-1: I2C BUS START/STOP BITS REQUIREMENTS I2C AC Characteristics Standard Operating Conditions (unless otherwise specified) Operating Temperature –40°C ≤ TA ≤ +125°C (Extended) Operating Voltage V range is described in Section2.0 “Typical DD Performance Curves” Param. Symbol Characteristic Min Max Units Conditions No. F Standard Mode 0 100 kHz C = 400pF, 1.8V - 5.5V SCL b Fast Mode 0 400 kHz C = 400pF, 2.7V - 5.5V b D102 Cb Bus capacitive 100kHz mode — 400 pF loading 400kHz mode — 400 pF 90 TSU:STA START condition 100kHz mode 4700 — ns Only relevant for repeated Setup time 400kHz mode 600 — ns START condition 91 THD:STA START condition 100kHz mode 4000 — ns After this period the first Hold time 400kHz mode 600 — ns clock pulse is generated 92 TSU:STO STOP condition 100kHz mode 4000 — ns Setup time 400kHz mode 600 — ns 93 THD:STO STOP condition 100kHz mode 4000 — ns Hold time 400kHz mode 600 — ns 103 100 102 101 SCL 90 106 91 107 92 SDA In 109 109 110 SDA Out Note1: Refer to specification D102 (Cb) for load conditions. FIGURE 1-2: I2C Bus Data Timing. © 2009 Microchip Technology Inc. DS22147A-page 9

MCP4017/18/19 TABLE 1-2: I2C BUS DATA REQUIREMENTS (SLAVE MODE) I2C AC Characteristics Standard Operating Conditions (unless otherwise specified) Operating Temperature –40°C ≤ TA ≤ +125°C (Extended) Operating Voltage VDD range is described in AC/DC characteristics Parame- Sym Characteristic Min Max Units Conditions ter No. 100 T Clock high time 100kHz mode 4000 — ns 1.8V-5.5V HIGH 400kHz mode 600 — ns 2.7V-5.5V 101 TLOW Clock low time 100kHz mode 4700 — ns 1.8V-5.5V 400kHz mode 1300 — ns 2.7V-5.5V 102A (5) TRSCL SCL rise time 100kHz mode — 1000 ns Cb is specified to be from 10 to 400pF 400kHz mode 20 + 0.1Cb 300 ns 102B (5) TRSDA SDA rise time 100kHz mode — 1000 ns Cb is specified to be from 10 to 400pF 400kHz mode 20 + 0.1Cb 300 ns 103A (5) TFSCL SCL fall time 100kHz mode — 300 ns Cb is specified to be from 10 to 400pF 400kHz mode 20 + 0.1Cb 40 ns 103B (5) TFSDA SDA fall time 100kHz mode — 300 ns Cb is specified to be from 10 to 400pF 400kHz mode 20 + 0.1Cb (4) 300 ns 106 THD:DAT Data input hold 100kHz mode 0 — ns 1.8V-5.5V, Note 6 time 400kHz mode 0 — ns 2.7V-5.5V, Note 6 107 TSU:DAT Data input 100kHz mode 250 — ns (2) setup time 400kHz mode 100 — ns 109 TAA Output valid 100kHz mode — 3450 ns (1) from clock 400kHz mode — 900 ns 110 T Bus free time 100kHz mode 4700 — ns Time the bus must be free BUF before a new transmission 400kHz mode 1300 — ns can start T Input filter spike 100kHz mode — 50 ns Philips Spec states N.A. SP suppression 400kHz mode — 50 ns (SDA and SCL) Note1: As a transmitter, the device must provide this internal minimum delay time to bridge the undefined region (min. 300ns) of the falling edge of SCL to avoid unintended generation of START or STOP conditions. 2: A fast-mode (400kHz) I2C-bus device can be used in a standard-mode (100kHz) I2C-bus system, but the requirement tsu; DAT≥250ns must then be met. This will automatically be the case if the device does not stretch the LOW period of the SCL signal. If such a device does stretch the LOW period of the SCL signal, it must output the next data bit to the SDA line TR max.+tsu;DAT=1000+250=1250ns (according to the standard-mode I2C bus specification) before the SCL line is released. 3: The MCP4018/MCP4019 device must provide a data hold time to bridge the undefined part between VIH and VIL of the falling edge of the SCL signal. This specification is not a part of the I2C specification, but must be tested in order to guarantee that the output data will meet the setup and hold specifications for the receiv- ing device. 4: Use Cb in pF for the calculations. 5: Not Tested. 6: A Master Transmitter must provide a delay to ensure that difference between SDA and SCL fall times do not unintentionally create a Start or Stop condition. DS22147A-page 10 © 2009 Microchip Technology Inc.

MCP4017/18/19 TEMPERATURE CHARACTERISTICS Electrical Specifications: Unless otherwise indicated, V =+1.8V to +5.5V, V =GND. DD SS Parameters Sym Min Typ Max Units Conditions Temperature Ranges Specified Temperature Range T -40 — +125 °C A Operating Temperature Range T -40 — +125 °C A Storage Temperature Range T -65 — +150 °C A Thermal Package Resistances Thermal Resistance, 5L-SC70 θ — 331 — °C/W JA (Note1) Thermal Resistance, 6L-SC70 θ — TBD — °C/W JA Note 1: Package Power Dissipation (PDIS) is calculated as follows: P = (T - T ) / θ , DIS J A JA where: T = Junction Temperature, T = Ambient Temperature. J A © 2009 Microchip Technology Inc. DS22147A-page 11

MCP4017/18/19 NOTES: DS22147A-page 12 © 2009 Microchip Technology Inc.

MCP4017/18/19 2.0 TYPICAL PERFORMANCE CURVES Note: The graphs and tables provided following this note are a statistical summary based on a limited number of samples and are provided for informational purposes only. The performance characteristics listed herein are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified operating range (e.g., outside specified power supply range) and therefore outside the warranted range. Note: Unless otherwise indicated, T = +25°C, V = 5V, V = 0V. A DD SS 60 2 A) 1.8 50 e (µ 1.6 5.5V v 1.4 A) 40 400 kHz, 5.5V nacti 1.2 (µD 30 ce I 0.81 D a I 1200 400 kHz, 2.7V 10100 k0H kzH, z5,. 52V.7V I InterfDD 000...246 2.7V 0 0 -40 0 40 80 120 -40 0 40 80 120 Temperature (°C) Temperature (°C) FIGURE 2-1: Interface Active Current FIGURE 2-2: Interface Inactive Current (I ) vs. SCL Frequency (f ) and Temperature (I ) vs. Temperature and V . DD SCL SHDN DD (V = 1.8V, 2.7V and 5.5V). (V = 1.8V, 2.7V and 5.5V). DD DD © 2009 Microchip Technology Inc. DS22147A-page 13

MCP4017/18/19 Note: Unless otherwise indicated, T = +25°C, V = 5V, V = 0V. A DD SS 120 0.3 120 0.3 -40C Rw 25C Rw 85C Rw 125C Rw -40C Rw 25C Rw 85C Rw 125C Rw -40C INL 25C INL 85C INL 125C INL -40C INL 25C INL 85C INL 125C INL ) W 100 -40C DNL 25C DNL 85C DNL 125C DNL 0.2 ) W 100 -40C DNL 25C DNL 85C DNL 125C DNL 0.2 Wiper Resistance (R(ohms)468000 -I4N0L°C 25°C85°C 125°C DNL RW --0000.1..21Error (LSb) Wiper Resistance (R(ohms)468000 -40°C RW 85°C 2152°5C°C DNL --0000.1..21Error (LSb) INL 20 -0.3 20 -0.3 0 32 64 96 0 32 64 96 Wiper Setting (decimal) Wiper Setting (decimal) FIGURE 2-3: 5.0kΩ : Pot Mode – R (Ω), FIGURE 2-6: 5.0kΩ : Rheo Mode – R W W INL (LSb), DNL (LSb) vs. Wiper Setting and (Ω), INL (LSb), DNL (LSb) vs. Wiper Setting and Temperature (V = 5.5V). (A = V , B = V ). Temperature (V = 5.5V).(I = 1.4mA, B = V ) DD DD SS DD W SS 300 3 300 0.3 -40C Rw 25C Rw 85C Rw 125C Rw -40C Rw 25C Rw 85C Rw 125C Rw -40C INL 25C INL 85C INL 125C INL Wiper Resistance (R) W(ohms)11122048266000000 -40--°44C00CC 82IDN55NL°°LC1252255°CCC IDNNLLDNL8855CC IDNNLL 1122R55CCWI IDNNNLLL --00000..12..21Error (LSb) Wiper Resistance (R) W(ohms)11122048266000000 25°8-C450°CC DN1L25°C25C DNLDNL85C DNL RW12I5NCL DNL 012 Error (LSb) -40°C 20 -0.3 20 -1 0 32 64 96 0 32 64 96 Wiper Setting (decimal) Wiper Setting (decimal) FIGURE 2-4: 5.0kΩ : Pot Mode – R (Ω), FIGURE 2-7: 5.0kΩ : Rheo Mode – R W W INL (LSb), DNL (LSb) vs. Wiper Setting and (Ω), INL (LSb), DNL (LSb) vs. Wiper Setting and Temperature (V = 2.7V). (A = V , B = V ) Temperature (V = 2.7V).(I = 450uA, B = V ) DD DD SS DD W SS 2500 0.35 2500 -40C Rw 25C Rw 85C Rw 125C Rw 44 -40C Rw 25C Rw 85C Rw 125C Rw -40C INL 25C INL 85C INL 125C INL Wiper Resistance (R) W(ohms)112050500000000 --R4400WCC IDNNLL 2255CCIN IDNLNLL 8855CC IDNDNLNLL 112255CC IDNNLL ---000000...012...210555555Error (LSb) Wiper Resistance (R) W(ohms)112050500000000 -40C DNLDNL2R5CW DNL 85C DNLINL125C DNL 9112233494949 Error (LSb) 4 0 -0.35 0 -1 0 32 64 96 0 32 64 96 Wiper Setting (decimal) Wiper Setting (decimal) Note: Refer to AN1080 for additional informa- Note: Refer to AN1080 for additional informa- tion on the characteristics of the wiper tion on the characteristics of the wiper resistance (R ) with respect to device resistance (R ) with respect to device W W voltage and wiper setting value. voltage and wiper setting value. FIGURE 2-5: 5.0kΩ : Pot Mode – R (Ω), FIGURE 2-8: 5.0kΩ : Rheo Mode – R W W INL (LSb), DNL (LSb) vs. Wiper Setting and (Ω), INL (LSb), DNL (LSb) vs. Wiper Setting and Temperature (V = 1.8V). (A = V , B = V ) Temperature (V = 1.8V). (I = TBD, B = V ) DD DD SS DD W SS DS22147A-page 14 © 2009 Microchip Technology Inc.

MCP4017/18/19 Note: Unless otherwise indicated, T = +25°C, V = 5V, V = 0V. A DD SS 0.0 200 Sb) -0.2 180 ull-Scale Error (FSE) (L -------1111000.......6420864 1.8V 2.75.5V R Tempco (PPM)BW 11110246246800000000 2.7V 5.5V F -1.8 0 -40 0 40 80 120 0 32 64 96 Ambient Temperature (°C) Wiper Setting (decimal) FIGURE 2-9: 5.0kΩ : Full Scale Error FIGURE 2-12: 5.0kΩ : R Tempco BW (FSE) vs. Temperature (V = 5.5V, 2.7V, 1.8V). ΔR / ΔT vs. Code. DD WB 1.8 b) 1.6 S L E) ( 1.4 S 1.2 Z or ( 1.0 1.8V Err 0.8 2.7 ale 0.6 c S 0.4 o- 5.5V er 0.2 Z 0.0 -40 0 40 80 120 Ambient Temperature (°C) FIGURE 2-10: 5.0kΩ : Zero Scale Error FIGURE 2-13: 5.0kΩ : Power-Up Wiper (ZSE) vs. Temperature (V = 5.5V, 2.7V, 1.8V). Response Time. DD 5200 ) B 5180 RA 5160 e ( 5140 c al Resistan(Ohms) 5555001168020000 2.7V 1.8V WVipDeDr n mi 5040 o N 5020 5.5V 5000 -40 0 40 80 120 Ambient Temperature (°C) FIGURE 2-11: 5.0kΩ : Nominal Resistance FIGURE 2-14: 5.0kΩ : Digital Feedthrough (Ω) vs. Temperature and V . (SCL signal coupling to Wiper pin). DD © 2009 Microchip Technology Inc. DS22147A-page 15

MCP4017/18/19 Note: Unless otherwise indicated, T = +25°C, V = 5V, V = 0V. A DD SS FIGURE 2-15: 5.0kΩ : Write Wiper (40h → FIGURE 2-18: 5.0kΩ : Write Wiper (FFh → 3Fh) Settling Time (V =5.5V). 00h) Settling Time (V =5.5V). DD DD FIGURE 2-16: 5.0kΩ : Write Wiper (40h FIGURE 2-19: 5.0kΩ : Write Wiper (FFh → → 3Fh) Settling Time (V =2.7V). 00h) Settling Time (V =2.7V). DD DD FIGURE 2-17: 5.0kΩ : Write Wiper (40h → FIGURE 2-20: 5.0kΩ : Write Wiper (FFh → 3Fh) Settling Time (V =1.8V). 00h) Settling Time (V =1.8V). DD DD DS22147A-page 16 © 2009 Microchip Technology Inc.

MCP4017/18/19 Note: Unless otherwise indicated, T = +25°C, V = 5V, V = 0V. A DD SS 120 0.3 120 0.3 -40C Rw 25C Rw 85C Rw 125C Rw -40C Rw 25C Rw 85C Rw 125C Rw -40C INL 25C INL 85C INL 125C INL -40C INL 25C INL 85C INL 125C INL ) W 100 -40C DNL 25C DNL 85C DNL 125C DNL 0.2 ) W 100 -40C DNL 25C DNL 85C DNL 125C DNL 0.2 Wiper Resistance (R(ohms)468000 -40°C DNL 8255°°CC 12IN5°LC RW --0000.1..21Error (LSb) Wiper Resistance (R(ohms)468000 -40°C 8255°°CC 125IN°CL DNL RW --0000.1..21Error (LSb) 20 -0.3 20 -0.3 0 32 64 96 0 32 64 96 Wiper Setting (decimal) Wiper Setting (decimal) FIGURE 2-21: 10kΩ Pot Mode : R (Ω), FIGURE 2-24: 10kΩ Rheo Mode : R (Ω), W W INL (LSb), DNL (LSb) vs. Wiper Setting and INL (LSb), DNL (LSb) vs. Wiper Setting and Temperature (V = 5.5V). (A = V , B = V ) Temperature (V = 5.5V).(I = 450uA, B = V ) DD DD SS DD W SS 300 3 300 0.3 -40C Rw 25C Rw 85C Rw 125C Rw -40C Rw 25C Rw 85C Rw 125C Rw -40C INL 25C INL 85C INL 125C INL Wiper Resistance (R) W(ohms)11122048266000000 -40--°44C00CC IDNNL2LI5N°LC2255CC IDNNLLDN8L588°55CC IDNNLL 11122255RCC5W °IDNCNLL --00000..12..21Error (LSb) Wiper Resistance (R) W(ohms)11122048266000000 -402°5C-°4C0C DN8L5°C25C DDNNL1L25°C85C DNINLL 125C DRNWL 012 Error (LSb) 20 -0.3 20 -1 0 32 64 96 0 32 64 96 Wiper Setting (decimal) Wiper Setting (decimal) FIGURE 2-22: 10kΩ Pot Mode : R (Ω), FIGURE 2-25: 10kΩ Rheo Mode : R (Ω), W W INL (LSb), DNL (LSb) vs. Wiper Setting and INL (LSb), DNL (LSb) vs. Wiper Setting and Temperature (V = 2.7V). (A = V , B = V ) Temperature (V = 2.7V).(I = 210uA, B = V ) DD DD SS DD W SS 0.35 -40C Rw 25C Rw 85C Rw 125C Rw 39 -40C Rw 25C Rw 85C Rw 125C Rw -40C INL 25C INL 85C INL 125C INL ) W 3000 --4400CC IDNNLL 2255CC IDNNLL 8855CC IDNNLL 112255CC IDNNLL 0.25 ) W 3000 -40C DNL 25C DNL 85C DNL 125C DNL 34 Wiper Resistance (R(ohms)12000000 RW DNL INL ---00000..01...21055555Error (LSb) Wiper Resistance (R(ohms)12000000 RW DNL INL 4911224949 Error (LSb) 0 -0.35 0 -1 0 32 64 96 0 32 64 96 Wiper Setting (decimal) Wiper Setting (decimal) Note: Refer to AN1080 for additional informa- Note: Refer to AN1080 for additional informa- tion on the characteristics of the wiper tion on the characteristics of the wiper resistance (RW) with respect to device resistance (RW) with respect to device voltage and wiper setting value. voltage and wiper setting value. FIGURE 2-23: 10kΩ Pot Mode : R (Ω), FIGURE 2-26: 10kΩ Rheo Mode : R (Ω), W W INL (LSb), DNL (LSb) vs. Wiper Setting and INL (LSb), DNL (LSb) vs. Wiper Setting and Temperature (V = 1.8V). (A = V , B = V ) Temperature (V = 1.8V). (I = TBD, B = V ) DD DD SS DD W SS © 2009 Microchip Technology Inc. DS22147A-page 17

MCP4017/18/19 Note: Unless otherwise indicated, T = +25°C, V = 5V, V = 0V. A DD SS 0.0 100 b) -0.1 S E) (L --00..32 PM) 80 2.7V S P e Error (F ---000...654 2.7 5.5V Tempco ( 4600 al -0.7 W 5.5V c B ull-S --00..98 1.8V R 20 F -1.0 0 -40 0 40 80 120 0 32 64 96 Ambient Temperature (°C) Wiper Setting (decimal) FIGURE 2-27: 10kΩ : Full Scale Error FIGURE 2-30: 10kΩ : RBW Tempco (FSE) vs. Temperature (VDD = 5.5V, 2.7V, 1.8V). ΔRWB / ΔT vs. Code. 0.9 b) 0.8 S L E) ( 0.7 S 0.6 Z 1.8V or ( 0.5 2.7 Err 0.4 ale 0.3 c S 0.2 5.5V o- er 0.1 Z 0.0 -40 0 40 80 120 Ambient Temperature (°C) FIGURE 2-28: 10kΩ : Zero Scale Error FIGURE 2-31: 10kΩ : Power-Up Wiper (ZSE) vs. Temperature (V = 5.5V, 2.7V, 1.8V). Response Time. DD 10200 ) AB 10150 R nce ( 10100 Wiper esistaOhms) 10050 1.8V VDD al R( 10000 n mi 2.7 o 9950 N 5.5V 9900 -40 0 40 80 120 Ambient Temperature (°C) FIGURE 2-29: 10kΩ : Nominal Resistance FIGURE 2-32: 10kΩ : Digital Feedthrough (Ω) vs. Temperature and V . (SCL signal coupling to Wiper pin). DD DS22147A-page 18 © 2009 Microchip Technology Inc.

MCP4017/18/19 Note: Unless otherwise indicated, T = +25°C, V = 5V, V = 0V. A DD SS FIGURE 2-33: 10kΩ : Write Wiper (40h → FIGURE 2-36: 10kΩ : Write Wiper (FFh → 3Fh) Settling Time (V =5.5V). 00h) Settling Time (V =5.5V). DD DD FIGURE 2-34: 10kΩ : Write Wiper (40h → FIGURE 2-37: 10kΩ : Write Wiper (FFh → 3Fh) Settling Time (V =2.7V). 00h) Settling Time (V =2.7V). DD DD FIGURE 2-35: 10kΩ : Write Wiper (40h → FIGURE 2-38: 10kΩ : Write Wiper (FFh → 3Fh) Settling Time (V =1.8V). 00h) Settling Time (V =1.8V). DD DD © 2009 Microchip Technology Inc. DS22147A-page 19

MCP4017/18/19 Note: Unless otherwise indicated, T = +25°C, V = 5V, V = 0V. A DD SS 120 0.3 120 0.3 -40C Rw 25C Rw 85C Rw 125C Rw -40C Rw 25C Rw 85C Rw 125C Rw -40C INL 25C INL 85C INL 125C INL -40C INL 25C INL 85C INL 125C INL ) W 100 -40C DNL 25C DNL 85C DNL 125C DNL 0.2 ) W 100 -40C DNL 25C DNL 85C DNL 125C DNL 0.2 Wiper Resistance (R(ohms)468000 -40°C IN8L5°C DN12L5°C25°C RW --0000.1..21Error (LSb) Wiper Resistance (R(ohms)468000 -40°C 2855°°CC DNL125°ICNL RW --0000.1..21Error (LSb) 20 -0.3 20 -0.3 0 32 64 96 0 32 64 96 Wiper Setting (decimal) Wiper Setting (decimal) FIGURE 2-39: 50kΩ Pot Mode : R (Ω), FIGURE 2-42: 50kΩ Rheo Mode : R (Ω), W W INL (LSb), DNL (LSb) vs. Wiper Setting and INL (LSb), DNL (LSb) vs. Wiper Setting and Temperature (V = 5.5V). Temperature (V = 5.5V).(I = 90uA, B = V ) DD DD W SS 300 0.3 300 0.3 -40C Rw 25C Rw 85C Rw 125C Rw -40C Rw 25C Rw 85C Rw 125C Rw -40C INL 25C INL 85C INL 125C INL Wiper Resistance (R) W(ohms)11122048266000000 --4400CC IDN2NL5L°C822555°CC IDNNLL DN88L55CC IDNINLNLL 11122255R5CC° WIDCNNLL --00000..12..21Error (LSb) Wiper Resistance (R) W(ohms)11122048266000000 25-°84C05C°C DNL 2152C5 D°NCLDNL85C DNL R1W25CIN DLNL --00000..12..21 Error (LSb) -40°C -40°C 20 -0.3 20 -0.3 0 32 64 96 0 32 64 96 Wiper Setting (decimal) Wiper Setting (decimal) FIGURE 2-40: 50kΩ Pot Mode : R (Ω), FIGURE 2-43: 50kΩ Rheo Mode : R (Ω), W W INL (LSb), DNL (LSb) vs. Wiper Setting and INL (LSb), DNL (LSb) vs. Wiper Setting and Temperature (V = 2.7V). Temperature (V = 2.7V).(I = 45uA, B = V ) DD DD W SS 10000 23 10000 0.35 -40C Rw 25C Rw 85C Rw 125C Rw -40C Rw 25C Rw 85C Rw 125C Rw -40C INL 25C INL 85C INL 125C INL 21 R) W 8000 --4400CC DINNLL 2255CC IDNNLL 8855CC IDNNLL 112255CC IDNNLL 0.25 R) W 8000 -40C DNL 25C DNL 85C DNL 125C DNL 1179 Wiper Resistance ((ohms) 246000000000 DINNLL RW ---00000..01...21055555Error (LSb) Wiper Resistance ((ohms) 246000000000 DNL RW INL 3579111135 Error (LSb) 1 0 -0.35 0 -1 0 32 64 96 0 32 64 96 Wiper Setting (decimal) Wiper Setting (decimal) Note: Refer to AN1080 for additional informa- Note: Refer to AN1080 for additional informa- tion on the characteristics of the wiper tion on the characteristics of the wiper resistance (RW) with respect to device resistance (RW) with respect to device voltage and wiper setting value. voltage and wiper setting value. FIGURE 2-41: 50kΩ Pot Mode : R (Ω), FIGURE 2-44: 50kΩ Rheo Mode : R (Ω), W W INL (LSb), DNL (LSb) vs. Wiper Setting and INL (LSb), DNL (LSb) vs. Wiper Setting and Temperature (V = 1.8V). Temperature (V = 1.8V). (I = TBD, B = V ) DD DD W SS DS22147A-page 20 © 2009 Microchip Technology Inc.

MCP4017/18/19 Note: Unless otherwise indicated, T = +25°C, V = 5V, V = 0V. A DD SS 0.00 100 b) S L ull-Scale Error (FSE) ( ---000...100284 21..78V 5.5V R Tempco (PPM)BW 24680000 2.7V 5.5V F -0.16 0 -40 0 40 80 120 0 32 64 96 Ambient Temperature (°C) Wiper Setting (decimal) FIGURE 2-45: 50kΩ : Full Scale Error FIGURE 2-48: 50kΩ : R Tempco BW (FSE) vs. Temperature (V = 5.5V, 2.7V, 1.8V). ΔR / ΔT vs. Code. DD WB 0.20 b) S E) (L 0.16 S 1.8V or (Z 0.12 Err 0.08 2.7 e al c S 0.04 ero- 5.5V Z 0.00 -40 0 40 80 120 Ambient Temperature (°C) FIGURE 2-46: 50kΩ : Zero Scale Error FIGURE 2-49: 50kΩ : Power-Up Wiper (ZSE) vs. Temperature (V = 5.5V, 2.7V, 1.8V). Response Time. DD 49800 ) B RA 49600 e ( stancms) 49400 Wiper al Resi(Oh 49200 1.8V VDD n mi 49000 2.7V o N 5.5V 48800 -40 0 40 80 120 Ambient Temperature (°C) FIGURE 2-47: 50kΩ : Nominal Resistance FIGURE 2-50: 50kΩ : Digital Feedthrough (Ω) vs. Temperature and V . (SCL signal coupling to Wiper pin). DD © 2009 Microchip Technology Inc. DS22147A-page 21

MCP4017/18/19 Note: Unless otherwise indicated, T = +25°C, V = 5V, V = 0V. A DD SS FIGURE 2-51: 50kΩ : Write Wiper (40h → FIGURE 2-54: 50kΩ : Write Wiper (FFh → 3Fh) Settling Time (V =5.5V). 00h) Settling Time (V =5.5V). DD DD FIGURE 2-52: 50kΩ : Write Wiper (40h → FIGURE 2-55: 50kΩ : Write Wiper (FFh → 3Fh) Settling Time (V =2.7V). 00h) Settling Time (V =2.7V). DD DD FIGURE 2-53: 50kΩ : Write Wiper (40h → FIGURE 2-56: 50kΩ : Write Wiper (FFh → 3Fh) Settling Time (V =1.8V). 00h) Settling Time (V =1.8V). DD DD DS22147A-page 22 © 2009 Microchip Technology Inc.

MCP4017/18/19 Note: Unless otherwise indicated, T = +25°C, V = 5V, V = 0V. A DD SS 120 0.3 120 0.3 -40C Rw 25C Rw 85C Rw 125C Rw -40C Rw 25C Rw 85C Rw 125C Rw -40C INL 25C INL 85C INL 125C INL -40C INL 25C INL 85C INL 125C INL R) W 100 -40C DNL85°C25C1 D2N5L°C 85DC NDNLL 125C DNL 0.2 R) W 100 -40C DNL85°C25C DNL125°8C5C DNDLNL 125C DNL 0.2 er Resistance ((ohms)6800 INL -000.1.1Error (LSb) er Resistance ((ohms)6800 -000.1.1Error (LSb) Wip 40 -40°C 25°C RW -0.2 Wip 40 -40°C 25°C INL RW -0.2 20 -0.3 20 -0.3 0 32 64 96 0 32 64 96 Wiper Setting (decimal) Wiper Setting (decimal) FIGURE 2-57: 100kΩ Pot Mode : R (Ω), FIGURE 2-60: 100kΩ Rheo Mode : R W W INL (LSb), DNL (LSb) vs. Wiper Setting and (Ω), INL (LSb), DNL (LSb) vs. Wiper Setting and Temperature (V = 5.5V). Temperature (V = 5.5V). (I = 45uA, B = V ) DD DD W SS 300 0.3 300 0.3 -40C Rw 25C Rw 85C Rw 125C Rw -40C Rw 25C Rw 85C Rw 125C Rw -40C INL 25C INL 85C INL 125C INL Wiper Resistance (R) W(ohms)11122048266000000 DN--44L00CC IDNNL2L5°C2255CC8 5IDN°NLL 1288555CC° CIDINNNLLL 1122R55CCW IDNNLL --00000..12..21Error (LSb) Wiper Resistance (R) W(ohms)11122048266000000 -40CIN DLNL25°C25C DNLDN8L5°8C5C DN1L25°CR1W25C DNL --00000..12..21 Error (LSb) -40°C -40°C 20 -0.3 20 -0.3 0 32 64 96 0 32 64 96 Wiper Setting (decimal) Wiper Setting (decimal) FIGURE 2-58: 100kΩ Pot Mode : R (Ω), FIGURE 2-61: 100kΩ Rheo Mode : R W W INL (LSb), DNL (LSb) vs. Wiper Setting and (Ω), INL (LSb), DNL (LSb) vs. Wiper Setting and Temperature (V = 2.7V). Temperature (V = 2.7V). (I = 21uA, B = V ) DD DD W SS 15000 15000 0.35 -40C Rw 25C Rw 85C Rw 125C Rw 19 -40C Rw 25C Rw 85C Rw 125C Rw -40C INL 25C INL 85C INL 125C INL ) W 12500 --4400CC DINNLL 2255CC IDNNLL 8855CC IDNNLL 112255CC IDNNLL 0.25 ) W 12500 -40C DNL 25C DNL 85C DNL 125C DNL 17 Wiper Resistance (R(ohms)10257050500000000 DNL INL ---00000..01...21055555Error (LSb) Wiper Resistance (R(ohms)10257050500000000 DNL RW INL 3579111135 Error (LSb) RW 1 0 -0.35 0 -1 0 32 64 96 0 32 64 96 Wiper Setting (decimal) Wiper Setting (decimal) Note: Refer to AN1080 for additional informa- Note: Refer to AN1080 for additional informa- tion on the characteristics of the wiper tion on the characteristics of the wiper resistance (R ) with respect to device resistance (R ) with respect to device W W voltage and wiper setting value. voltage and wiper setting value. FIGURE 2-59: 100kΩ Pot Mode : R (Ω), FIGURE 2-62: 100kΩ Rheo Mode : R W W INL (LSb), DNL (LSb) vs. Wiper Setting and (Ω), INL (LSb), DNL (LSb) vs. Wiper Setting and Temperature (V = 1.8V). Temperature (V = 1.8V). (I = TBD, B = V ) DD DD W SS © 2009 Microchip Technology Inc. DS22147A-page 23

MCP4017/18/19 Note: Unless otherwise indicated, T = +25°C, V = 5V, V = 0V. A DD SS 0.00 100 b) S L Full-Scale Error (FSE) ( ---000...000642 1.8V 2.57.5V R Tempco (PPM)BW 24680000 2.7V 5.5V -0.08 0 -40 0 40 80 120 0 32 64 96 Ambient Temperature (°C) Wiper Setting (decimal) FIGURE 2-63: 100kΩ : Full Scale Error FIGURE 2-66: 100kΩ : R Tempco BW (FSE) vs. Temperature (V = 5.5V, 2.7V, 1.8V). ΔR / ΔT vs. Code. DD WB 0.12 b) S L E) ( S 0.08 Z or ( 1.8V Err ale 0.04 2.7 c S o- er 5.5V Z 0.00 -40 0 40 80 120 Ambient Temperature (°C) FIGURE 2-64: 100kΩ : Zero Scale Error FIGURE 2-67: 100kΩ : Power-Up Wiper (ZSE) vs. Temperature (V = 5.5V, 2.7V, 1.8V). Response Time. DD 99800 ) B 99600 RA 99400 e ( 99200 c al Resistan(Ohms) 99998889468000000000 2.7V1.8V WVipDeDr n mi 98200 o N 98000 5.5V 97800 -40 0 40 80 120 Ambient Temperature (°C) FIGURE 2-65: 100kΩ : Nominal FIGURE 2-68: 100kΩ : Digital Resistance (Ω) vs. Temperature and V . Feedthrough (SCL signal coupling to Wiper pin). DD DS22147A-page 24 © 2009 Microchip Technology Inc.

MCP4017/18/19 Note: Unless otherwise indicated, T = +25°C, V = 5V, V = 0V. A DD SS FIGURE 2-69: 100kΩ : Write Wiper (40h FIGURE 2-72: 100kΩ : Write Wiper (FFh → 3Fh) Settling Time (V = 5.5V). → 00h) Settling Time (V = 5.5V). DD DD FIGURE 2-70: 100kΩ : Write Wiper (40h FIGURE 2-73: 100kΩ : Write Wiper (FFh → 3Fh) Settling Time (V = 2.7V). → 00h) Settling Time (V = 2.7V). DD DD FIGURE 2-71: 100kΩ : Write Wiper (40h FIGURE 2-74: 100kΩ : Write Wiper (FFh → 3Fh) Settling Time (V = 1.8V). → 00h) Settling Time (V = 1.8V). DD DD © 2009 Microchip Technology Inc. DS22147A-page 25

MCP4017/18/19 Note: Unless otherwise indicated, T = +25°C, V = 5V, V = 0V. A DD SS 4 0.3 3.5 5.5V 0.25 3 2.7V (@ 3mA) 0.2 V) 2.5 2.7V mV) V (IH 1.52 V (OL 0.15 5.5V (@ 3mA) 0.1 1 1.8V (@ 1mA) 0.05 0.5 1.8V 0 0 -40 0 40 80 120 -40 0 40 80 120 Temperature (°C) Temperature (°C) FIGURE 2-75: V (SCL, SDA) vs. V and FIGURE 2-77: V (SDA) vs. V and IH DD OL DD Temperature. Temperature. 2 1.2 1 5.5 5.5V 1.5 V 2.7V 0.8 V (V)IL 1 V (V)DD 0.6 2.7V 0.4 0.5 1.8V 0.2 0 0 -40 0 40 80 120 -40 0 40 80 120 Temperature (°C) Temperature (°C) FIGURE 2-76: V (SCL, SDA) vs. V and FIGURE 2-78: POR/BOR Trip point vs. V IL DD DD Temperature. and Temperature. DS22147A-page 26 © 2009 Microchip Technology Inc.

MCP4017/18/19 Note: Unless otherwise indicated, T = +25°C, V = 5V, V = 0V. A DD SS 10 10 Code = 7Fh Code = 7Fh 0 0 Code = 3Fh -10 Code = 3Fh -10 Code = 1Fh -20 B -20 B Code = 0Fh d d Code = 0Fh Code = 1Fh -30 -30 Code = 01h Code = 01h -40 -40 -50 -50 -60 100 1,000 10,000 100 1,000 10,000 Frequency (kHz) Frequency (kHz) FIGURE 2-79: 5kΩ – Gain vs. Frequency FIGURE 2-82: 100kΩ – Gain vs. (-3dB). Frequency (-3dB). 2.1 Test Circuits 10 Code = 7Fh 0 Code = 3Fh +5V -10 +5V -20 B Code = 0Fh A d -30 Code = 01h Code = 1Fh VIN W + VOUT -40 B - -50 -60 100 1,000 10,000 Frequency (kHz) FIGURE 2-80: 10kΩ – Gain vs. Frequency (-3dB). FIGURE 2-83: Gain vs. Frequency Test (-3dB). 10 Code = 7Fh 0 -10 Code = 3Fh -20 Code = 1Fh B d Code = 0Fh -30 Code = 01h -40 -50 -60 100 1,000 10,000 Frequency (kHz) FIGURE 2-81: 50kΩ – Gain vs. Frequency (-3dB). © 2009 Microchip Technology Inc. DS22147A-page 27

MCP4017/18/19 NOTES: DS22147A-page 28 © 2009 Microchip Technology Inc.

MCP4017/18/19 3.0 PIN DESCRIPTIONS The descriptions of the pins are listed in Table3-1. Additional descriptions of the device pins follow. TABLE 3-1: PINOUT DESCRIPTION FOR THE MCP4017/18/19 Pin Number Pin Pin Buffer Function Name MCP4017 MCP4018 MCP4019 Type Type (SC70-6) (SC70-6) (SC70-5) V 1 1 1 P — Positive Power Supply Input DD V 2 2 2 P — Ground SS SCL 3 3 3 I/O ST (OD) I2C Serial Clock pin SDA 4 4 4 I/O ST (OD) I2C Serial Data pin B 5 — — I/O A Potentiometer Terminal B W 6 5 5 I/O A Potentiometer Wiper Terminal A — 6 — I/O A Potentiometer Terminal A Legend: A = Analog input ST (OD) = Schmitt Trigger with Open Drain I = Input O = Output I/O = Input/Output P = Power © 2009 Microchip Technology Inc. DS22147A-page 29

MCP4017/18/19 3.1 Positive Power Supply Input (V ) W pin can support both positive and negative current. DD The voltage on terminal W must be between V and SS The VDD pin is the device’s positive power supply input. VDD. The input power supply is relative to V and can range SS from 1.8V to 5.5V. A de-coupling capacitor on V (to DD 3.7 Potentiometer Terminal A V ) is recommended to achieve maximum SS performance. The terminal A pin (available on some devices) is connected to the internal potentiometer’s terminal A. While the device’s voltage is in the range of 1.8V ≤ V DD < 2.7V, the Resistor Network’s electrical performance The potentiometer’s terminal A is the fixed connection of the device may not meet the data sheet to the Full Scale (0x7F tap) wiper value of the digital specifications. potentiometer. The terminal A pin is available on the MCP4018 3.2 Ground (V ) SS devices. The terminal A pin does not have a polarity relative to the terminal W pin. The terminal A pin can The V pin is the device ground reference. SS support both positive and negative current. The voltage 3.3 I2C Serial Clock (SCL) on Terminal A must be between VSS and VDD. The terminal A pin is not available on the MCP4017 The SCL pin is the serial clock pin of the I2C interface. and MCP4019 devices. For these devices, the The MCP401X acts only as a slave and the SCL pin potentiometer’s terminal A is internally floating. accepts only external serial clocks. The SCL pin is an open-drain output. Refer to Section5.0 “Serial Interface - I2C Module” for more details of I2C Serial Interface communication. 3.4 I2C Serial Data (SDA) The SDA pin is the serial data pin of the I2C interface. The SDA pin has a Schmitt trigger input and an open-drain output. Refer to Section5.0 “Serial Interface - I2C Module” for more details of I2C Serial Interface communication. 3.5 Potentiometer Terminal B The terminal B pin (available on some devices) is connected to the internal potentiometer’s terminal B. The potentiometer’s terminal B is the fixed connection to the Zero Scale (0x00 tap) wiper value of the digital potentiometer. The terminal B pin is available on the MCP4017 device. The terminal B pin does not have a polarity relative to the terminal W pin. The terminal B pin can support both positive and negative current. The voltage on terminal B must be between V and V . SS DD The terminal B pin is not available on the MCP4018 and MCP4019 devices. For these devices, the potentiometer’s terminal B is internally connected to V . SS 3.6 Potentiometer Wiper (W) Terminal The terminal W pin is connected to the internal potentiometer’s terminal W (the wiper). The wiper terminal is the adjustable terminal of the digital potentiometer. The terminal W pin does not have a polarity relative to terminals A or B pins. The terminal DS22147A-page 30 © 2009 Microchip Technology Inc.

MCP4017/18/19 4.0 GENERAL OVERVIEW 4.1.2 BROWN-OUT RESET When the device powers down, the device V will The MCP4017/18/19 devices are general purpose DD cross the V /V voltage. Once the V voltage digital potentiometers intended to be used in POR BOR DD decreases below the V /V voltage the following applications where a programmable resistance with POR BOR happens: moderate bandwidth is desired. • Serial Interface is disabled This Data Sheet covers a family of three Digital Potentiometer and Rheostat devices. The MCP4018 If the V voltage decreases below the V voltage DD RAM device is the Potentiometer configuration, while the the following happens: MCP4017 and MCP4019 devices are the Rheostat • Volatile wiper registers may become corrupted configuration. As the voltage recovers above the V /V voltage POR BOR Applications generally suited for the MCP401X devices see Section4.1.1 “Power-on Reset”. include: Serial commands not completed due to a Brown-out • Set point or offset trimming condition may cause the memory location to become • Sensor calibration corrupted. • Selectable gain and offset amplifier designs 4.1.3 WIPER REGISTER (RAM) • Cost-sensitive mechanical trim pot replacement The Wiper Register is volatile memory that starts As the Device Block Diagram shows, there are four functioning at the RAM retention voltage (V ). The main functional blocks. These are: RAM Wiper Register will be loaded with the default wiper • POR/BOR Operation value when V will rise above the V /V voltage. DD POR BOR • Serial Interface - I2C Module • Resistor Network 4.1.4 DEVICE CURRENTS The POR/BOR operation and the Memory Map are The current of the device can be classified into two discussed in this section and the I2C and Resistor modes of the device operation. These are: Network operation are described in their own sections. • Serial Interface Inactive (Static Operation) The Serial Commands commands are discussed in • Serial Interface Active Section5.4. Static Operation occurs when a Stop condition is 4.1 POR/BOR Operation received. Static Operation is exited when a Start condition is received. The Power-on Reset is the case where the device is having power applied to it from V . The Brown-out SS Reset occurs when a device had power applied to it, and that power (voltage) drops below the specified range. The devices RAM retention voltage (V ) is lower RAM than the POR/BOR voltage trip point (V /V ). The POR BOR maximum V /V voltage is less then 1.8V. POR BOR When V /V < V < 2.7V, the Resistor Network’s POR BOR DD electrical performance may not meet the data sheet specifications. In this region, the device is capable of reading and writing to its volatile memory if the proper serial command is executed. Table4-1 shows the digital pot’s level of functionality across the entire V range, while Figure4-1 illustrates DD the Power-up and Brown-out functionality. 4.1.1 POWER-ON RESET When the device powers up, the device V will cross DD the V /V voltage. Once the V voltage crosses POR BOR DD the V /V voltage, the following happens: POR BOR • Volatile wiper register is loaded with the default wiper value (3Fh) • The device is capable of digital operation © 2009 Microchip Technology Inc. DS22147A-page 31

MCP4017/18/19 TABLE 4-1: DEVICE FUNCTIONALITY AT EACH V REGION (NOTE1) DD Serial Potentiometer V Level Wiper Setting Comment DD Interface Terminals V < V < 1.8V Ignored “unknown” Unknown DD BOR V ≤ V < 1.8V “Unknown” Operational with Wiper Register loaded BOR DD reduced electrical with POR/BOR value specs 1.8V ≤ V < 2.7V Accepted Operational with Wiper Register Electrical performance may not DD reduced electrical determines Wiper meet the data sheet specifications. specs Setting 2.7V ≤ V ≤ 5.5V Accepted Operational Wiper Register Meets the data sheet specifications DD determines Wiper Setting Note 1: For system voltages below the minimum operating voltage, the customer will be recommended to use a voltage supervisor to hold the system in reset. This will ensure that MCP4017/18/19 commands are not attempted out of the operating range of the device. Normal Operation Range Normal Operation Range V Outside Specified DD AC/DC Range 2.7V 1.8V V POR/BOR V RAM V SS Analog Analog Characteristics Characteristics not specified not specified Device’s Serial Interface is VBOR Delay “Not Operational” Wiper Forced to Default POR/BOR setting FIGURE 4-1: Power-up and Brown-out. DS22147A-page 32 © 2009 Microchip Technology Inc.

MCP4017/18/19 5.0 SERIAL INTERFACE - 5.1 I2C I/O Considerations I2C MODULE I2C specifications require active low, passive high A 2-wire I2C serial protocol is used to write or read the functionality on devices interfacing to the bus. Since digital potentiometer’s wiper register. The I2C protocol devices may be operating on separate power supply sources, ESD clamping diodes are not permitted. The utilizes the SCL input pin and SDA input/output pin. specification recommends using open drain transistors The I2C serial interface supports the following features. tied to V (common) with a pull-up resistor. The SS • Slave mode of operation specification makes some general recommendations on the size of this pull-up, but does not specify the • 7-bit addressing exact value since bus speeds and bus capacitance • The following clock rate modes are supported: impacts the pull-up value for optimum system - Standard mode, bit rates up to 100kb/s performance. - Fast mode, bit rates up to 400kb/s Common pull-up values range from 1kΩ to a max of • Support Multi-Master Applications ~10kΩ. Power sensitive applications tend to choose The serial clock is generated by the Master. higher values to minimize current losses during The I2C Module is compatible with the Phillips I2C communication but these applications also typically utilize lower V . specification. Phillips only defines the field types, field DD lengths, timings, etc. of a frame. The frame content The SDA and SCL float (are not driving) when the defines the behavior of the device. The frame content device is powered down. for the MCP4017, MCP4018, and MCP4019 devices A "glitch" filter is on the SCL and SDA pins when the pin are defined in this section of the Data Sheet. is an input. When these pins are an output, there is a Figure5-1 shows a typical I2C bus configurations. slew rate control of the pin that is independent of device frequency. Single I2C Bus Configuration 5.1.1 SLOPE CONTROL The device implements slope control on the SDA Device 1 Device 3 Device n output. The slope control is defined by the fast mode Host specifications. Controller For Fast (FS) mode, the device has spike suppression and Schmidt trigger inputs on the SDA and SCL pins. Device 2 Device 4 FIGURE 5-1: Typical Application I2C Bus Configurations. Refer to Section2.0 “Typical Performance Curves”, AC/DC Electrical Characteristics table for detailed input threshold and timing specifications. © 2009 Microchip Technology Inc. DS22147A-page 33

MCP4017/18/19 5.2 I2C Bit Definitions If the Slave Address is not valid, the Slave Device will issue a Not A (A). The A bit will have the SDA signal I2C bit definitions include: high. • Start Bit If an error condition occurs (such as an A instead of A) • Data Bit then an START bit must be issued to reset the • Acknowledge (A) Bit command state machine. • Repeated Start Bit TABLE 5-1: MCP4017/18/19 A / A • Stop Bit RESPONSES • Clock Stretching Figure5-8 shows the waveform for these states. Acknowledge Event Comment Bit Response 5.2.1 START BIT General Call A The Start bit (see Figure5-2) indicates the beginning of Slave Address A a data transfer sequence. The Start bit is defined as the valid SDA signal falling when the SCL signal is “High”. Slave Address A not valid 1st Bit 2nd Bit Bus Collision N.A. I2C Module Resets, SDA or a “Don’t Care” if the collision occurs SCL on the Masters S “Start bit”. FIGURE 5-2: Start Bit. 5.2.2 DATA BIT 5.2.4 REPEATED START BIT The SDA signal may change state while the SCL signal The Repeated Start bit (see Figure5-5) indicates the is Low. While the SCL signal is High, the SDA signal current Master Device wishes to continue MUST be stable (see Figure5-3). communicating with the current Slave Device without releasing the I2C bus. The Repeated Start condition is the same as the Start condition, except that the 1st Bit 2nd Bit SDA Repeated Start bit follows a Start bit (with the Data bits + A bit) and not a Stop bit. SCL The Start bit is the beginning of a data transfer S sequence and is defined as the SDA signal falling when FIGURE 5-3: Data Bit. the SCL signal is “High”. 5.2.3 ACKNOWLEDGE (A) BIT Note1: A bus collision during the Repeated Start condition occurs if: The A bit (see Figure5-4) is a response from the Slave • SDA is sampled low when SCL goes device to the Master device. Depending on the context from low to high. of the transfer sequence, the A bit may indicate different things. Typically the Slave device will supply • SCL goes low before SDA is asserted an A response after the Start bit and 8 “data” bits have low. This may indicate that another mas- been received. The A bit will have the SDA signal low. ter is attempting to transmit a data "1". SDA D0 A SDA 1st Bit SCL 8 9 FIGURE 5-4: Acknowledge Waveform. SCL Sr = Repeated Start FIGURE 5-5: Repeat Start Condition Waveform. DS22147A-page 34 © 2009 Microchip Technology Inc.

MCP4017/18/19 5.2.5 STOP BIT 5.2.7 ABORTING A TRANSMISSION The Stop bit (see Figure5-6) Indicates the end of the If any part of the I2C transmission does not meet the I2C Data Transfer Sequence. The Stop bit is defined as command format, it is aborted. This can be intentionally the SDA signal rising when the SCL signal is “High”. accomplished with a START or STOP condition. This is A Stop bit resets the I2C interface of the other devices. done so that noisy transmissions (usually an extra START or STOP condition) are aborted before they corrupt the device. SDA A / A 5.2.8 IGNORING AN I2C TRANSMISSION AND “FALLING OFF” THE BUS SCL The MCP4017/18/19 expects to receive entire, valid P I2C commands and will assume any command not FIGURE 5-6: Stop Condition Receive or defined as a valid command is due to a bus corruption and will enter a passive high condition on the SDA Transmit Mode. signal. All signals will be ignored until the next valid 5.2.6 CLOCK STRETCHING START condition and CONTROL BYTE are received. “Clock Stretching” is something that the Secondary Device can do, to allow additional time to “respond” to the “data” that has been received. The MCP4017/18/19 will not strech the clock signal (SCL) since memory read accesses occur fast enough. SDA SCL S 1st 2nd 3rd 4th 5th 6th 7th 8th A/A 1st 2nd 3rd 4th 5th 6th 7th 8th A/A P Bit Bit Bit Bit Bit Bit Bit Bit Bit Bit Bit Bit Bit Bit Bit Bit FIGURE 5-7: Typical 16-bit I2C Waveform Format. SDA SCL START Data allowed Data or STOP Condition to change A valid Condition FIGURE 5-8: I2C Data States and Bit Sequence. © 2009 Microchip Technology Inc. DS22147A-page 35

MCP4017/18/19 5.2.9 I2C COMMAND PROTOCOL TABLE 5-2: DEVICE I2C ADDRESS The MCP4017/18/19 is a slave I2C device which Device I2C Address Comment supports 7-bit slave addressing. The slave address MCP4017 ‘0101111’ contains seven fixed bits. Figure5-9 shows the control MCP4018 ‘0101111’ byte format. MCP4019 ‘0101111’ 5.2.9.1 Control Byte (Slave Address) The Control Byte is always preceded by a START 5.2.9.2 Hardware Address Pins condition. The Control Byte contains the slave address consisting of seven fixed bits and the R/W bit. Figure5- The MCP4017/MCP4018/MCP4019 does not support 9 shows the control byte format and Table5-2 shows hardware address bits. the I2C address for the devices. 5.2.10 GENERAL CALL Slave Address The General Call is a method that the Master device can communicate with all other Slave devices. S A6 A5 A4 A3 A2 A1 A0 R/W A/A The MCP4017/18/19 devices do not respond to “0”“1” “0”“1” “1” “1”“1” General Call address and commands, and therefore the communications are Not Acknowledged. Start R/W bit bit R/W = 0 = write R/W = 1 = read A bit (controlled by slave device) A = 0 = Slave Device Acknowledges byte A = 1 = Slave Device does not Acknowledge byte FIGURE 5-9: Slave Address Bits in the I2C Control Byte. Second Byte S 0 0 0 0 0 0 0 0 A x x x x X x x 0 A P General Call Address “7-bit Command” Reserved 7-bit Commands (By I2C Specification - Philips # 9398 393 40011, Ver. 2.1 January 2000) ‘0000 011’b - Reset and write programmable part of slave address by hardware. ‘0000 010’b - Write programmable part of slave address by hardware. ‘0000 000’b - NOT Allowed The Following is a “Hardware General Call” Format Second Byte n occurrences of (Data + A / A) S 0 0 0 0 0 0 0 0 A x x x x X x x 1 A x x x x X x x X A P General Call Address “7-bit Command” This indicates a “Hardware General Call” MCP4016/7/8/9 will ignore this byte and all following bytes (and A), until a Stop bit (P) is encountered. FIGURE 5-10: General Call Formats. DS22147A-page 36 © 2009 Microchip Technology Inc.

MCP4017/18/19 5.3 Software Reset Sequence The Stop bit terminates the current I2C bus activity. The MCP4017/18/19 wait to detect the next Start condition. Note: This technique should be supported by any I2C compliant device. The 24xxxx I2C This sequence does not effect any other I2C devices which may be on the bus, as they should disregard this Serial EEPROM devices support this tech- as an invalid command. nique, which is documented in AN1028. At times it may become necessary to perform a 5.4 Serial Commands Software Reset Sequence to ensure the MCP4017/18/ 19 device is in a correct and known I2C Interface state. The MCP4017/18/19 devices support 2 serial This only resets the I2C state machine. commands. These commands are: This is useful if the MCP4017/18/19 device powers up • Write Operation in an incorrect state (due to excessive bus noise, etc), • Read Operations or if the Master Device is reset during communication. Figure5-11 shows the communication sequence to software reset the device. S ‘1’ ‘1’ ‘1’ ‘1’ ‘1’ ‘1’ ‘1’ ‘1’ S P Nine bits of ‘1’ Start bit Start bit Stop bit FIGURE 5-11: Software Reset Sequence Format. The 1st Start bit will cause the device to reset from a state in which it is expecting to receive data from the Master Device.In this mode, the device is monitoring the data bus in Receive mode and can detect the Start bit forces an internal Reset. The nine bits of ‘1’ are used to force a Reset of those devices that could not be reset by the previous Start bit. This occurs only if the MCP4017/18/19 is driving an A on the I2C bus, or is in output mode (from a Read command) and is driving a data bit of ‘0’ onto the I2C bus. In both of these cases, the previous Start bit could not be generated due to the MCP4017/18/19 holding the bus low. By sending out nine ‘1’ bits, it is ensured that the device will see a A (the Master Device does not drive the I2C bus low to acknowledge the data sent by the MCP4017/18/19), which also forces the MCP4017/ 18/19 to reset. The 2nd Start bit is sent to address the rare possibility of an erroneous write. This could occur if the Master Device was reset while sending a Write command to the MCP4017/18/19, AND then as the Master Device returns to normal operation and issues a Start condition while the MCP4017/18/19 is issuing an A. In this case if the 2nd Start bit is not sent (and the Stop bit was sent) the MCP4017/18/19 could initiate a write cycle. Note: The potential for this erroneous write ONLY occurs if the Master Device is reset while sending a Write command to the MCP4017/18/19. © 2009 Microchip Technology Inc. DS22147A-page 37

MCP4017/18/19 5.4.1 WRITE OPERATION 5.4.2 READ OPERATIONS The write operation requires the START condition, The read operation requires the START condition, Control Byte, Acknowledge, Data Byte, Acknowledge Control Byte, Acknowledge, Data Byte, the master and STOP (or RESTART) condition. The Control (Slave generating the A and STOP condition. The Control Address) Byte requires the R/W bit equal to a logic zero Byte requires the R/W bit equal to a logic one (R/W = (R/W = “0”) to generate a write sequence. The 1) to generate a read sequence. The MCP4017/18/19 MCP4017/18/19 is responsible for generating the will A the Slave Address Byte and A all the Data Bytes. Acknowledge (A) bits. The I2C Master will A the Slave Address Byte and the last Data Byte. If there are multiple Data Bytes, the I2C Data is written to the MCP4017/18/19 after every byte Master will A all Data Bytes except the last Data Byte transfer (during the A bit). If a STOP or RESTART (which it will A). condition is generated during a data transfer (before The MCP4017/18/19 maintains control of the SDA the A bit), the data will not be written to MCP4017/18/ signal until all data bits have been clocked out. 19. Data bytes may be written after each Acknowledge. The command is terminated once a Stop (P) condition The command is terminated once a Stop (P) condition occurs. Refer to Figure5-13 for the read command occurs. Refer to Figure5-12 for the write sequence. sequence. For a single read, the master sends a STOP For a single byte write, the master sends a STOP or or RESTART condition after the 1st data byte (and A RESTART condition after the 1st data byte is sent. bit) is sent from the slave. Figure5-14 shows the I2C communication behavior of The MSb of each Data Byte is a don’t care, since the the Master Device and the MCP4017/18/19 device and wiper register is only 7-bits wide. the resultant I2C bus values. Figure5-14 shows the I2C communication behavior of the Master Device and the MCP4017/18/19 device and the resultant I2C bus values. Fixed Read/Write bit (“0” = Write) Address S 0 1 0 1 1 1 1 0 A x D6 D5D4D3D2 D1D0 A x D6 D5D4 D3 D2D1D0 A Slave Address Byte Data Byte Data Byte STOP bit x D6 D5D4D3D2 D1D0 A x D6D5 D4D3 D2 D1D0 A P Data Byte Data Byte Legend S = Start Condition P = Stop Condition A = Acknowledge X = Don’t Care R/W = Read/Write bit D6, D5, D4, D3, D2, D1, D0 = Data bits FIGURE 5-12: I2C Write Command Format. DS22147A-page 38 © 2009 Microchip Technology Inc.

MCP4017/18/19 Fixed Read/Write bit (“1” = Read) Address S 0 1 0 1 1 1 1 1 A 0 D6 D5D4D3D2 D1D0 A(1)0 D6 D5D4 D3 D2D1D0 A(1) Slave Address Byte Data Byte Data Byte STOP bit (2) 0 D6 D5D4D3D2 D1D0 A(1)0 D6 D5 D4D3 D2 D1D0 A P Data Byte Data Byte Legend S = Start Condition P = Stop Condition A = Acknowledge X = Don’t Care R/W = Read/Write bit Note1 = Data bits Note1: Master Device is responsible for A / A signal. If a A signal occurs, the MCP4017/18/19 will abort this transfer and release the bus. 2: The Master Device will A, and the MCP4017/18/19 will release the bus so the Master Device can generate a Stop or Repeated Start condition. FIGURE 5-13: I2C Read Command Format. © 2009 Microchip Technology Inc. DS22147A-page 39

MCP4017/18/19 Write 1 Byte R / S Slave Address WA Data Byte (1) A P Master S 0 1 0 1 1 1 1 0 1 x d d d d d d d 1 P MCP4017/18/19 0 0 I2C Bus S 0 1 0 1 1 1 1 0 0 x d d d d d d d 0 P Write 2 Bytes R / S Slave Address WA Data Byte (1) A Data Byte (1) A P Master S 0 1 0 1 1 1 1 0 1 x d d d d d d d 1 x d d d d d d d 1 P MCP4017/18/19 0 0 0 I2C Bus S 0 1 0 1 1 1 1 0 0 x d d d d d d d 0 x d d d d d d d 1 P Read 1 Byte R / S Slave Address WA Data Byte A P Master S 0 1 0 1 1 1 1 1 1 1 P MCP4017/18/19 0 0 d d d d d d d 1 I2C Bus S 0 1 0 1 1 1 1 1 0 0 d d d d d d d 1 P Read 2 Bytes R / S Slave Address WA Data Byte A Data Byte A P Master S 0 1 0 1 1 1 1 1 1 0 1 P MCP4017/18/19 0 0 d d d d d d d 1 0 d d d d d d d 1 I2C Bus S 0 1 0 1 1 1 1 1 0 0 d d d d d d d 0 0 d d d d d d d 1 P Note1: For Write Commands, the MSb of the Data Byte is a don’t care since the wiper register is only 7-bits wide. FIGURE 5-14: I2C Communication Behavior. DS22147A-page 40 © 2009 Microchip Technology Inc.

MCP4017/18/19 6.0 RESISTOR NETWORK A The Resistor Network is made up of two parts. These N = 127 7Fh are: RW (1) • Resistor Ladder R S • Wiper N = 126 7Eh Figure6-1 shows a block diagram for the resistive network. RS RW (1) Digital potentiometer applications can be divided into N = 125 7Dh two resistor network categories: RW (1) R • Rheostat configuration S • Potentiometer (or voltage divider) configuration The MCP4017 is a true rheostat, with terminal B and W the wiper (W) of the variable resistor available on pins. N = 1 01h The MCP4018 device offers a voltage divider (potentiometer) with terminal B internally connected to R RW (1) S ground. N = 0 00h The MCP4019 device is a Rheostat device with terminal A of the resistor floating, terminal B internally RW (1) B connected to ground, and the wiper (W) available on Analog pin. Mux Note1: The wiper resistance is tap dependent. 6.1 Resistor Ladder Module That is, each tap selection resistance has a small variation. This variation has The resistor ladder is a series of equal value resistors more effect on devices with smaller R (R ) with a connection point (tap) between the two AB S resistance (5.0kΩ). resistors. The total number of resistors in the series (ladder) determines the R resistance (see Figure6- AB FIGURE 6-1: Resistor Network Block 1). The end points of the resistor ladder are connected Diagram. to the device Terminal A and Terminal B pins. The R AB (and R ) resistance has small variations over voltage S TABLE 6-1: WIPER SETTING MAP and temperature. The Resistor Network has 127 resistors in a string Wiper Setting Properties between terminal A and terminal B. This gives 7-bits of 07Fh Full Scale (W = A) resolution. 07Eh - 040h W = N The wiper can be set to tap onto any of these 127 03Fh W = N (Mid Scale) resistors thus providing 128 possible settings 03Eh - 001h W = N (including terminal A and terminal B). This allows zero 000h Zero Scale (W = B) scale to full scale connections. A wiper setting of 00h connects the Terminal W (wiper) to Terminal B (Zero Scale). A wiper setting of 3Fh is the Mid scale setting. A wiper setting of 7Fh connects the Terminal W (wiper) to Terminal A (Full Scale). Table6- 1 illustrates the full wiper setting map. Terminal A and B as well as the wiper W do not have a polarity. These terminals can support both positive and negative current. © 2009 Microchip Technology Inc. DS22147A-page 41

MCP4017/18/19 Step resistance (R ) is the resistance from one tap A POR/BOR event will load the Volatile Wiper register S setting to the next. This value will be dependent on the value with the default value. Table6-3 shows the R value that has been selected. Equation6-1 shows default values offered. AB the calculation for the step resistance while Table6-2 shows the typical step resistances for each device. TABLE 6-3: DEFAULT FACTORY SETTINGS SELECTION EQUATION 6-1: R CALCULATION S Default POR Wiper Resistance Typical R R = ----A----B- Code RAB Value Setting Code (1) S 127 -502 5.0kΩ Mid-scale 3Fh Equation6-2 illustrates the calculation used to -103 10.0kΩ Mid-scale 3Fh determine the resistance between the wiper and -503 50.0kΩ Mid-scale 3Fh terminal B. -104 100.0kΩ Mid-scale 3Fh EQUATION 6-2: R CALCULATION Note1: Custom POR/BOR Wiper Setting options WB are available, contact the local Microchip R N R = ----A----B------+R Sales Office for additional information. WB 127 W Custom options have minimum volume N = 0 to 127 (decimal) requirements. The digital potentiometer is available in four nominal resistances (R ) where the nominal resistance is AB defined as the resistance between terminal A and terminal B. The four nominal resistances are 5kΩ, 10kΩ, 50kΩ, and 100kΩ. The total resistance of the device has minimal variation due to operating voltage (see Figure2-11, Figure2-29, Figure2-47, or Figure2-65). TABLE 6-2: STEP RESISTANCES Resistance (Ω) Part Number Total Case Step (R ) (R ) S AB Min. 4000 31.496 MCP4017/18/19-502E Typical 5000 39.370 Max. 6000 47.244 Min. 8000 62.992 MCP4017/18/19-103E Typical 10000 78.740 Max. 12000 94.488 Min. 40000 314.961 MCP4017/18/19-503E Typical 50000 393.701 Max. 60000 472.441 Min. 80000 629.921 MCP4017/18/19-104E Typical 100000 787.402 Max. 120000 944.882 DS22147A-page 42 © 2009 Microchip Technology Inc.

MCP4017/18/19 6.2 Resistor Configurations 6.2.2 POTENTIOMETER CONFIGURATION 6.2.1 RHEOSTAT CONFIGURATION When used as a potentiometer, all three terminals of When used as a rheostat, two of the three digital the device are tied to different nodes in the circuit. This potentiometer’s terminals are used as a resistive allows the potentiometer to output a voltage element in the circuit. With terminal W (wiper) and proportional to the input voltage. This configuration is either terminal A or terminal B, a variable resistor is sometimes called voltage divider mode. The created. The resistance will depend on the tap setting potentiometer is used to provide a variable voltage by of the wiper (and the wiper’s resistance). The adjusting the wiper position between the two endpoints resistance is controlled by changing the wiper setting as shown in Figure6-3. Reversing the polarity of the A The unused terminal (B or A) should be left floating. and B terminals will not affect operation. Figure6-2 shows the two possible resistors that can be used. Reversing the polarity of the A and B terminals V 1 will not affect operation. A V W 3 A B W RAW or RBW V2 B FIGURE 6-3: Potentiometer Configuration. Resistor The temperature coefficient of the R resistors is AB FIGURE 6-2: Rheostat Configuration. minimal by design. In this configuration, the resistors all change uniformly, so minimal variation should be seen. This allows the control of the total resistance between the two nodes. The total resistance depends on the The Wiper resistor temperature coefficient is different “starting” terminal to the Wiper terminal. So at the code to the R temperature coefficient. The voltage at node AB 00h, the R resistance is minimal (R ), but the R V3 (Figure6-3) is not dependent on this Wiper BW W AW resistance in maximized (R + R ). Conversely, at the resistance, just the ratio of the R resistors, so this AB W AB code 3Fh, the R resistance is minimal (R ), but the temperature coefficient in most cases can be ignored. AW W R resistance in maximized (R + R ). BW AB W Note: To avoid damage to the internal wiper The resistance Step size (RS) equates to one LSb of circuitry in this configuration, care should the resistor. be taken to insure the current flow never exceeds 2.5mA. Note: To avoid damage to the internal wiper circuitry in this configuration, care should be taken to insure the current flow never exceeds 2.5mA. The pinout for the rheostat devices is such that as the wiper register is incremented, the resistance of the resistor will increase (as measured from Terminal B to the W Terminal). © 2009 Microchip Technology Inc. DS22147A-page 43

MCP4017/18/19 6.3 Wiper Resistance In a potentiometer configuration, the wiper resistance variation does not effect the output voltage seen on the Wiper resistance is the series resistance of the analog W pin. switch that connects the selected resistor ladder node The slope of the resistance has a linear area (at the to the Wiper Terminal common signal (see Figure6-1). higher voltages) and a non-linear area (at the lower A value in the volatile wiper register selects which voltages). In where resistance increases faster then the analog switch to close, connecting the W terminal to voltage drop (at low voltages). the selected node of the resistor ladder. The resistance is dependent on the voltages on the analog switch source, gate, and drain nodes, as well as the device’s wiper code, temperature, and the current through the switch. As the device voltage decreases, the wiper resistance increases (see Figure6-4 and R W Table6-4). The wiper can connect directly to Terminal B or to Terminal A. A zero scale connections, connects the Terminal W (wiper) to Terminal B (wiper setting of 000h). A full scale connections, connects the Terminal V W (wiper) to Terminal A (wiper setting of 7Fh). In these DD configurations the only resistance between the Note: The slope of the resistance has a linear Terminal W and the other Terminal (A or B) is that of the area (at the higher voltages) and a non-linear area (at the lower voltages). analog switches. The wiper resistance is typically measured when the FIGURE 6-4: Relationship of Wiper wiper is positioned at either zero scale (00h) or full Resistance (R ) to Voltage. W scale (3Fh). Since there is minimal variation of the total device The wiper resistance in potentiometer-generated resistance over voltage, at a constant temperature (see voltage divider applications is not a significant source Figure2-11, Figure2-29, Figure2-47, or Figure2-65), of error. the change in wiper resistance over voltage can have a The wiper resistance in rheostat applications can significant impact on the INL and DNL error. create significant nonlinearity as the wiper is moved toward zero scale (00h). The lower the nominal resistance, the greater the possible error. In a rheostat configuration, this change in voltage needs to be taken into account. Particularly for the lower resistance devices. For the 5.0kΩ device the maximum wiper resistance at 5.5V is approximately 3.2% of the total resistance, while at 2.7V it is approximately 6.5% of the total resistance. TABLE 6-4: TYPICAL STEP RESISTANCES AND RELATIONSHIP TO WIPER RESISTANCE Resistance (Ω) R / R (%) (1) R / R (%) (2) W S W AB Typical Wiper (R ) W R = R = Max R = Max R = R = Max R = Max W W W W W W Total Step Max @ Max @ Typical @ 5.5V @ 2.7V Typical @ 5.5V @ 2.7V Typical (R ) (R ) 5.5V 2.7V AB S 5000 39.37 100 170 325 254.00% 431.80% 825.5% 2.00% 3.40% 6.50% 10000 78.74 100 170 325 127.00% 215.90% 412.75% 1.00% 1.70% 3.25% 50000 393.70 100 170 325 25.40% 43.18% 82.55% 0.20% 0.34% 0.65% 100000 787.40 100 170 325 12.70% 21.59% 41.28% 0.10% 0.17% 0.325% Note 1: R is the typical value. The variation of this resistance is minimal over voltage. S 2: R is the typical value. The variation of this resistance is minimal over voltage. AB DS22147A-page 44 © 2009 Microchip Technology Inc.

MCP4017/18/19 6.4 Operational Characteristics 6.4.1.2 Differential Non-linearity (DNL) Understanding the operational characteristics of the DNL error is the measure of variations in code widths device’s resistor components is important to the system from the ideal code width. A DNL error of zero would design. imply that every code is exactly 1LSb wide. 6.4.1 ACCURACY 6.4.1.1 Integral Non-linearity (INL) 111 INL error for these devices is the maximum deviation 110 Actual between an actual code transition point and its transfer corresponding ideal transition point after offset and 101 function gain errors have been removed. These endpoints are Digital 100 from 0x00 to 0x7F. Refer to Figure6-5. Input Ideal transfer function Positive INL means higher resistance than ideal. Code 011 Negative INL means lower resistance than ideal. 010 Wide code, > 1 LSb 001 INL < 0 000 111 Narrow code < 1 LSb Actual 110 transfer function Digital Pot Output 101 FIGURE 6-6: DNL Accuracy. Digital 100 Input 6.4.1.3 Ratiometric temperature coefficient Code 011 Ideal transfer The ratiometric temperature coefficient quantifies the function error in the ratio RAW/RWB due to temperature drift. 010 This is typically the critical error when using a potentiometer device (MCP4018) in a voltage divider 001 configuration. 000 6.4.1.4 Absolute temperature coefficient INL < 0 The absolute temperature coefficient quantifies the Digital Pot Output error in the end-to-end resistance (Nominal resistance R ) due to temperature drift. This is typically the AB FIGURE 6-5: INL Accuracy. critical error when using a rheostat device (MCP4017 and MCP4019) in an adjustable resistor configuration. © 2009 Microchip Technology Inc. DS22147A-page 45

MCP4017/18/19 6.4.2 MONOTONIC OPERATION Monotonic operation means that the device’s resistance increases with every step change (from terminal A to terminal B or terminal B to terminal A). The wiper resistances difference at each tap location. When changing from one tap position to the next (either increasing or decreasing), the ΔR is less then the W ΔR . When this change occurs, the device voltage and S temperature are “the same” for the two tap positions. R S63 0x3F R S62 0x3E e d 0x3D o C ut p n R al I 0x03 S3 git R Di 0x02 S1 R S0 0x01 0x00 R W n = ? (@ tap) R = R + R BW Sn W(@ Tap n) n = 0 Resistance (R ) BW FIGURE 6-7: R . BW DS22147A-page 46 © 2009 Microchip Technology Inc.

MCP4017/18/19 7.0 DESIGN CONSIDERATIONS 7.2 Layout Considerations In the design of a system with the MCP4017/18/19 Inductively-coupled AC transients and digital switching devices, the following considerations should be taken noise can degrade the input and output signal integrity, into account. These are: potentially masking the MCP4017/18/19’s performance. Careful board layout will minimize these • The Power Supply effects and increase the Signal-to-Noise Ratio (SNR). • The Layout Bench testing has shown that a multi-layer board In the design of a system with the MCP4017/18/19 utilizing a low-inductance ground plane, isolated inputs, devices, the following considerations should be taken isolated outputs and proper decoupling are critical to into account: achieving the performance that the silicon is capable of providing. Particularly harsh environments may require • Power Supply Considerations shielding of critical signals. • Layout Considerations If low noise is desired, breadboards and wire-wrapped 7.1 Power Supply Considerations boards are not recommended. The typical application will require a bypass capacitor 7.2.1 RESISTOR TEMPCO in order to filter high-frequency noise, which can be Characterization curves of the resistor temperature induced onto the power supply's traces. The bypass coefficient (Tempco) are shown in Figure2-11, capacitor helps to minimize the effect of these noise Figure2-29, Figure2-47, and Figure2-65. sources on signal integrity. Figure7-1 illustrates an These curves show that the resistor network is appropriate bypass strategy. designed to correct for the change in resistance as In this example, the recommended bypass capacitor temperature increases. This technique reduces the value is 0.1µF. This capacitor should be placed as end to end change is R resistance. AB close to the device power pin (V ) as possible (within DD 4mm). The power source supplying these devices should be as clean as possible. If the application circuit has separate digital and analog power supplies, V and DD V should reside on the analog plane. SS V DD 0.1µF V DD 0.1µF er oll ntr o c o A 19 cr W 7/18/ SCL ®o Mi 1 cr 0 mi 4 P C B MC SDA PI V V SS SS FIGURE 7-1: Typical Microcontroller Connections. © 2009 Microchip Technology Inc. DS22147A-page 47

MCP4017/18/19 NOTES: DS22147A-page 48 © 2009 Microchip Technology Inc.

MCP4017/18/19 8.0 APPLICATIONS EXAMPLES V DD Digital potentiometers have a multitude of practical uses in modern electronic circuits. The most popular R 1 uses include precision calibration of set point thresholds, sensor trimming, LCD bias trimming, audio MCP4018 A attenuation, adjustable power supplies, motor control overcurrent trip setting, adjustable gain amplifiers and SDA W VOUT SCL offset trimming. The MCP4017/18/19 devices can be used to replace the common mechanical trim pot in B applications where the operating and terminal voltages are within CMOS process limitations (V = 2.7V to DD 5.5V). FIGURE 8-1: Using the Digital 8.1 Set Point Threshold Trimming Potentiometer to Set a Precise Output Voltage. Applications that need accurate detection of an input 8.1.1 TRIMMING A THRESHOLD FOR AN threshold event often need several sources of error OPTICAL SENSOR eliminated. Use of comparators and operational If the application has to calibrate the threshold of a amplifiers (op amps) with low offset and gain error can diode, transistor or resistor, a variation range of 0.1V is help achieve the desired accuracy, but in many common. Often, the desired a resolution of 2mV or applications, the input source variation is beyond the better is adequate to accurately detect the presence of designer’s control. If the entire system can be a precise signal. A “windowed” voltage divider, utilizing calibrated after assembly in a controlled environment the MCP4018, would be a potential solution. Figure8- (like factory test), these sources of error are minimized 2 illustrates this example application. if not entirely eliminated. Figure8-1 illustrates a common digital potentiometer configuration. This configuration is often referred to as VDD a “windowed voltage divider”. Note that R is not 1 necessary to create the voltage divider, but its presence is useful when the desired threshold has limited range. It is “windowed” because R can narrow 1 the adjustable range of V to a value much less than V TRIP DD V VDD – VSS. If the output range is reduced, the Rsense CC+ magnitude of each output step is reduced. This R 1 effectively increases the trimming resolution for a fixed digital potentiometer resolution. This technique may MCP4018 A Comparator allow a lower-cost digital potentiometer to be utilized SDA W VTRIP (64 steps instead of 256 steps). SCL MCP6021 The MCP4018’s low DNL performance is critical to B V 0.1µF CC– meeting calibration accuracy in production without having to use a higher precision digital potentiometer. EQUATION 8-1: CALCULATING THE FIGURE 8-2: Set Point or Threshold WIPER SETTING FROM Calibration. THE DESIRED V TRIP R V = V ⎛--------W-----B-----⎞ TRIP DD⎝R +R ⎠ 1 2 R = R AB Nominal D R = R • WB AB 127 V D = T R IP • (R + R ) • 127 V 1 AB DD D = Digital Potentiometer Wiper Setting (0-127) © 2009 Microchip Technology Inc. DS22147A-page 49

MCP4017/18/19 8.2 Operational Amplifier Applications Figure8-3 and Figure8-4 illustrate typical amplifier circuits that could replace fixed resistors with the MCP4017/18/19 to achieve digitally-adjustable analog solutions. MCP6291 VIN + V Op Amp DD V – OUT R 1 A R3 W B MCP4018 MCP4017 FIGURE 8-3: Trimming Offset and Gain in a Non-Inverting Amplifier. MCP4018 R 4 B A W V – DD Op Amp R 1 V V + OUT IN MCP6021 A W 1 B fc = 2----π----⋅----R-----------⋅---C--- Eq MCP4018 Thevenin R = (R +R –R )||(R +R )+R Equivalent Eq 1 AB WB 2 WB w FIGURE 8-4: Programmable Filter. DS22147A-page 50 © 2009 Microchip Technology Inc.

MCP4017/18/19 8.3 Temperature Sensor Applications The circuit illustrated by Figure8-6 utilizes a digital potentiometer for trimming the offset error. This Thermistors are resistors with very predictable solution removes R from the trimming equation along W variation with temperature. Thermistors are a popular with the error associated with R . R is not required, W 2 sensor choice when a low-cost temperature-sensing but can be utilized to reduce the trimming “window” and solution is desired. Unfortunately, thermistors have reduce variation due to the digital pot’s R part-to-part AB non-linear characteristics that are undesirable, typically variability. requiring trimming in an application to achieve greater accuracy. There are several common solutions to trim & linearize thermistors. Figure8-5 and Figure8-6 are VDD simple methods for linearizing a 3-terminal NTC thermistor. Both are simple voltage dividers using a Positive Temperature Coefficient (PTC) resistor (R ) R 1 1 with a transfer function capable of compensating for the NTC linearity error in the Negative Temperature Coefficient Thermistor (NTC) thermistor. The circuit, illustrated by Figure8-5, utilizes a digital rheostat for trimming the offset error caused by the thermistor’s part-to-part variation. This solution puts the V digital potentiometer’s R into the voltage divider OUT W MCP4018 calculation. The MCP4017/18/19’s R temperature AB coefficient is a low 50ppm (-20°C to +70°C). R ’s error W is substantially greater than R ’s error because R AB W varies with V , wiper setting and temperature. For the DD FIGURE 8-6: Thermistor Calibration using 50kΩ devices, the error introduced by R is, in most W cases, insignificant as long as the wiper setting is > 6. a Digital Potentiometer in a Potentiometer For the 2kΩ devices, the error introduced by R is Configuration. W significant because it is a higher percentage of R . WB For these reasons, the circuit illustrated in Figure8-5 is not the most optimum method for “exciting” and linearizing a thermistor. V DD R 1 NTC Thermistor V OUT R 2 MCP4017 FIGURE 8-5: Thermistor Calibration using a Digital Potentiometer in a Rheostat Configuration. © 2009 Microchip Technology Inc. DS22147A-page 51

MCP4017/18/19 8.4 Wheatstone Bridge Trimming Another common configuration to “excite” a sensor (such as a strain gauge, pressure sensor or thermistor) is the wheatstone bridge configuration. The wheatstone bridge provides a differential output instead of a single-ended output. Figure8-7 illustrates a wheatstone bridge utilizing one to three digital potentiometers. The digital potentiometers in this example are used to trim the offset and gain of the wheatstone bridge. V DD 5kΩ MCP4017 V OUT MCP4017 MCP4017 50kΩ 50kΩ FIGURE 8-7: Wheatstone Bridge Trimming. DS22147A-page 52 © 2009 Microchip Technology Inc.

MCP4017/18/19 9.0 DEVELOPMENT SUPPORT 9.2 Technical Documentation Several additional technical documents are available to 9.1 Development Tools assist you in your design and development. These technical documents include Application Notes, To assist in your design and evaluation of the Technical Briefs, and Design Guides. Table9-1 shows MCP4017/18/19 devices, a Demo board using the some of these documents. MCP4017 device is in development. Please check the Microchip web site for the release of this board. The board part number is tentatively MCP4XXXDM-PGA, and is expected to be available in the summer of 2009. TABLE 9-1: TECHNICAL DOCUMENTATION Application Title Literature # Note Number AN1080 Understanding Digital Potentiometers Resistor Variations DS01080 AN737 Using Digital Potentiometers to Design Low Pass Adjustable Filters DS00737 AN692 Using a Digital Potentiometer to Optimize a Precision Single Supply Photo Detect DS00692 AN691 Optimizing the Digital Potentiometer in Precision Circuits DS00691 AN219 Comparing Digital Potentiometers to Mechanical Potentiometers DS00219 — Digital Potentiometer Design Guide DS22017 — Signal Chain Design Guide DS21825 © 2009 Microchip Technology Inc. DS22147A-page 53

MCP4017/18/19 NOTES: DS22147A-page 54 © 2009 Microchip Technology Inc.

MCP4017/18/19 10.0 PACKAGING INFORMATION 10.1 Package Marking Information 5-Lead SC70 Example: Part Number Code MCP4019T-502E/LT BENN XXNN BENN MCP4019T-103E/LT BFNN MCP4019T-503E/LT BGNN MCP4019T-104E/LT BHNN 6-Lead SC70 Example: Part Number Code Part Number Code MCP4017T-502E/LT AENN MCP4018T-502E/LT AANN XXNN AANN MCP4017T-103E/LT AFNN MCP4018T-103E/LT ABNN MCP4017T-503E/LT AGNN MCP4018T-503E/LT ACNN MCP4017T-104E/LT AHNN MCP4018T-104E/LT ADNN Legend: XX...X Customer-specific information Y Year code (last digit of calendar year) YY Year code (last 2 digits of calendar year) WW Week code (week of January 1 is week ‘01’) NNN Alphanumeric traceability code e3 Pb-free JEDEC designator for Matte Tin (Sn) * This package is Pb-free. The Pb-free JEDEC designator ( e 3 ) can be found on the outer packaging for this package. Note: In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for customer-specific information. © 2009 Microchip Technology Inc. DS22147A-page 55

MCP4017/18/19 (cid:2)(cid:3)(cid:4)(cid:5)(cid:6)(cid:7)(cid:8)(cid:9)(cid:10)(cid:6)(cid:11)(cid:12)(cid:13)(cid:14)(cid:8)(cid:15)(cid:16)(cid:6)(cid:10)(cid:10)(cid:8)(cid:17)(cid:18)(cid:12)(cid:10)(cid:13)(cid:19)(cid:5)(cid:8)(cid:20)(cid:21)(cid:6)(cid:19)(cid:11)(cid:13)(cid:11)(cid:12)(cid:22)(cid:21)(cid:8)(cid:23)(cid:4)(cid:20)(cid:24)(cid:8)(cid:25)(cid:15)(cid:26)(cid:27)(cid:28)(cid:29) (cid:30)(cid:22)(cid:12)(cid:5)(cid:31) .(cid:10)(cid:9)(cid:2)#(cid:11)(cid:14)(cid:2)(cid:31)(cid:10) #(cid:2)(cid:8)$(cid:9)(cid:9)(cid:14)(cid:15)#(cid:2)(cid:12)(cid:28)(cid:8)/(cid:28)(cid:17)(cid:14)(cid:2)!(cid:9)(cid:28)-(cid:7)(cid:15)(cid:17) 0(cid:2)(cid:12)(cid:16)(cid:14)(cid:28) (cid:14)(cid:2) (cid:14)(cid:14)(cid:2)#(cid:11)(cid:14)(cid:2)(cid:6)(cid:7)(cid:8)(cid:9)(cid:10)(cid:8)(cid:11)(cid:7)(cid:12)(cid:2)1(cid:28)(cid:8)/(cid:28)(cid:17)(cid:7)(cid:15)(cid:17)(cid:2)(cid:22)(cid:12)(cid:14)(cid:8)(cid:7)%(cid:7)(cid:8)(cid:28)#(cid:7)(cid:10)(cid:15)(cid:2)(cid:16)(cid:10)(cid:8)(cid:28)#(cid:14)!(cid:2)(cid:28)#(cid:2) (cid:11)##(cid:12)+22---(cid:20)(cid:31)(cid:7)(cid:8)(cid:9)(cid:10)(cid:8)(cid:11)(cid:7)(cid:12)(cid:20)(cid:8)(cid:10)(cid:31)2(cid:12)(cid:28)(cid:8)/(cid:28)(cid:17)(cid:7)(cid:15)(cid:17) D b 3 2 1 E1 E 4 5 e e A A2 c A1 L 3(cid:15)(cid:7)# (cid:6)(cid:19)44(cid:19)(cid:6)"(cid:13)"(cid:26)(cid:22) (cid:21)(cid:7)(cid:31)(cid:14)(cid:15) (cid:7)(cid:10)(cid:15)(cid:2)4(cid:7)(cid:31)(cid:7)# (cid:6)(cid:19)5 56(cid:6) (cid:6)(cid:25)7 5$(cid:31)8(cid:14)(cid:9)(cid:2)(cid:10)%(cid:2)1(cid:7)(cid:15) 5 ( 1(cid:7)#(cid:8)(cid:11) (cid:14) (cid:4)(cid:20)9((cid:2))(cid:22)* 6,(cid:14)(cid:9)(cid:28)(cid:16)(cid:16)(cid:2):(cid:14)(cid:7)(cid:17)(cid:11)# (cid:25) (cid:4)(cid:20);(cid:4) < (cid:30)(cid:20)(cid:30)(cid:4) (cid:6)(cid:10)(cid:16)!(cid:14)!(cid:2)1(cid:28)(cid:8)/(cid:28)(cid:17)(cid:14)(cid:2)(cid:13)(cid:11)(cid:7)(cid:8)/(cid:15)(cid:14) (cid:25)(cid:3) (cid:4)(cid:20);(cid:4) < (cid:30)(cid:20)(cid:4)(cid:4) (cid:22)#(cid:28)(cid:15)!(cid:10)%% (cid:25)(cid:30) (cid:4)(cid:20)(cid:4)(cid:4) < (cid:4)(cid:20)(cid:30)(cid:4) 6,(cid:14)(cid:9)(cid:28)(cid:16)(cid:16)(cid:2)=(cid:7)!#(cid:11) " (cid:30)(cid:20);(cid:4) (cid:3)(cid:20)(cid:30)(cid:4) (cid:3)(cid:20)(cid:23)(cid:4) (cid:6)(cid:10)(cid:16)!(cid:14)!(cid:2)1(cid:28)(cid:8)/(cid:28)(cid:17)(cid:14)(cid:2)=(cid:7)!#(cid:11) "(cid:30) (cid:30)(cid:20)(cid:30)( (cid:30)(cid:20)(cid:3)( (cid:30)(cid:20)(cid:29)( 6,(cid:14)(cid:9)(cid:28)(cid:16)(cid:16)(cid:2)4(cid:14)(cid:15)(cid:17)#(cid:11) (cid:21) (cid:30)(cid:20);(cid:4) (cid:3)(cid:20)(cid:4)(cid:4) (cid:3)(cid:20)(cid:3)( .(cid:10)(cid:10)#(cid:2)4(cid:14)(cid:15)(cid:17)#(cid:11) 4 (cid:4)(cid:20)(cid:30)(cid:4) (cid:4)(cid:20)(cid:3)(cid:4) (cid:4)(cid:20)(cid:23)9 4(cid:14)(cid:28)!(cid:2)(cid:13)(cid:11)(cid:7)(cid:8)/(cid:15)(cid:14) (cid:8) (cid:4)(cid:20)(cid:4); < (cid:4)(cid:20)(cid:3)9 4(cid:14)(cid:28)!(cid:2)=(cid:7)!#(cid:11) 8 (cid:4)(cid:20)(cid:30)( < (cid:4)(cid:20)(cid:23)(cid:4) (cid:30)(cid:22)(cid:12)(cid:5)(cid:11)(cid:31) (cid:30)(cid:20) (cid:21)(cid:7)(cid:31)(cid:14)(cid:15) (cid:7)(cid:10)(cid:15) (cid:2)(cid:21)(cid:2)(cid:28)(cid:15)!(cid:2)"(cid:30)(cid:2)!(cid:10)(cid:2)(cid:15)(cid:10)#(cid:2)(cid:7)(cid:15)(cid:8)(cid:16)$!(cid:14)(cid:2)(cid:31)(cid:10)(cid:16)!(cid:2)%(cid:16)(cid:28) (cid:11)(cid:2)(cid:10)(cid:9)(cid:2)(cid:12)(cid:9)(cid:10)#(cid:9)$ (cid:7)(cid:10)(cid:15) (cid:20)(cid:2)(cid:6)(cid:10)(cid:16)!(cid:2)%(cid:16)(cid:28) (cid:11)(cid:2)(cid:10)(cid:9)(cid:2)(cid:12)(cid:9)(cid:10)#(cid:9)$ (cid:7)(cid:10)(cid:15) (cid:2) (cid:11)(cid:28)(cid:16)(cid:16)(cid:2)(cid:15)(cid:10)#(cid:2)(cid:14)&(cid:8)(cid:14)(cid:14)!(cid:2)(cid:4)(cid:20)(cid:30)(cid:3)(cid:5)(cid:2)(cid:31)(cid:31)(cid:2)(cid:12)(cid:14)(cid:9)(cid:2) (cid:7)!(cid:14)(cid:20) (cid:3)(cid:20) (cid:21)(cid:7)(cid:31)(cid:14)(cid:15) (cid:7)(cid:10)(cid:15)(cid:7)(cid:15)(cid:17)(cid:2)(cid:28)(cid:15)!(cid:2)#(cid:10)(cid:16)(cid:14)(cid:9)(cid:28)(cid:15)(cid:8)(cid:7)(cid:15)(cid:17)(cid:2)(cid:12)(cid:14)(cid:9)(cid:2)(cid:25)(cid:22)(cid:6)"(cid:2)’(cid:30)(cid:23)(cid:20)((cid:6)(cid:20) )(cid:22)*+ )(cid:28) (cid:7)(cid:8)(cid:2)(cid:21)(cid:7)(cid:31)(cid:14)(cid:15) (cid:7)(cid:10)(cid:15)(cid:20)(cid:2)(cid:13)(cid:11)(cid:14)(cid:10)(cid:9)(cid:14)#(cid:7)(cid:8)(cid:28)(cid:16)(cid:16)(cid:18)(cid:2)(cid:14)&(cid:28)(cid:8)#(cid:2),(cid:28)(cid:16)$(cid:14)(cid:2) (cid:11)(cid:10)-(cid:15)(cid:2)-(cid:7)#(cid:11)(cid:10)$#(cid:2)#(cid:10)(cid:16)(cid:14)(cid:9)(cid:28)(cid:15)(cid:8)(cid:14) (cid:20) (cid:6)(cid:7)(cid:8)(cid:9)(cid:10)(cid:8)(cid:11)(cid:7)(cid:12)(cid:13)(cid:14)(cid:8)(cid:11)(cid:15)(cid:10)(cid:16)(cid:10)(cid:17)(cid:18)(cid:21)(cid:9)(cid:28)-(cid:7)(cid:15)(cid:17)*(cid:4)(cid:23)(cid:27)(cid:4)9(cid:30)) DS22147A-page 56 © 2009 Microchip Technology Inc.

MCP4017/18/19 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging © 2009 Microchip Technology Inc. DS22147A-page 57

MCP4017/18/19 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging DS22147A-page 58 © 2009 Microchip Technology Inc.

MCP4017/18/19 Note: For the most current package drawings, please see the Microchip Packaging Specification located at http://www.microchip.com/packaging © 2009 Microchip Technology Inc. DS22147A-page 59

MCP4017/18/19 NOTES: DS22147A-page 60 © 2009 Microchip Technology Inc.

MCP4017/18/19 APPENDIX A: REVISION HISTORY Revision A (March 2009) • Original Release of this Document. © 2009 Microchip Technology Inc. DS22147A-page 61

MCP4017/18/19 NOTES: DS22147A-page 62 © 2009 Microchip Technology Inc.

MCP4017/18/19 PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. PART NO. XXX X /XX Examples: a) MCP4017T-502E/LT: 5kΩ, Device Resistance Temperature Package 6-LD SC-70. Version Range b) MCP4017T-103E/LT: 10kΩ, 6-LD SC-70. Device: MCP4017: Single Rheostat with I2C c) MCP4017T-503E/LT: 50kΩ, interface 6-LD SC-70. MCP4017T: Single Rheostat with I2C d) MCP4017T-104E/LT: 100kΩ, interface (Tape and Reel) 6-LD SC-70. MCP4018: Single Potentiometer to GND with I2C Interface a) MCP4018T-502E/LT: 5kΩ, MCP4018T: Single Potentiometer to GND with I2C Interface (Tape and 6-LD SC-70. b) MCP4018T-103E/LT: 10kΩ, Reel) 6-LD SC-70. MCP4019: Single Rheostat to GND with I2C Interface c) MCP4018T-503E/LT: 50kΩ, 6-LD SC-70. MCP4019T: Single Rheostat to GND with I2C Interface (Tape and Reel) d) MCP4018T-104E/LT: 100kΩ, 6-LD SC-70. Resistance 502 = 5kΩ a) MCP4019T-502E/LT: 5kΩ, Version: 103 = 10kΩ 5-LD SC-70. 503 = 50kΩ 104 = 100kΩ b) MCP4019T-103E/LT: 10kΩ, 5-LD SC-70. c) MCP4019T-503E/LT: 50kΩ, Temperature E = -40°C to +125°C 5-LD SC-70. Range: d) MCP4019T-104E/LT: 100kΩ, 5-LD SC-70. Package: LT = Plastic Small Outline Transistor (SC70), 5-lead, 6-lead © 2009 Microchip Technology Inc. DS22147A-page 63

MCP4017/18/19 NOTES: DS22147A-page 64 © 2009 Microchip Technology Inc.

Note the following details of the code protection feature on Microchip devices: • Microchip products meet the specification contained in their particular Microchip Data Sheet. • Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. • There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. • Microchip is willing to work with the customer who is concerned about the integrity of their code. • Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as “unbreakable.” Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device Trademarks applications and the like is provided only for your convenience The Microchip name and logo, the Microchip logo, Accuron, and may be superseded by updates. It is your responsibility to dsPIC, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, ensure that your application meets with your specifications. PICSTART, rfPIC, SmartShunt and UNI/O are registered MICROCHIP MAKES NO REPRESENTATIONS OR trademarks of Microchip Technology Incorporated in the WARRANTIES OF ANY KIND WHETHER EXPRESS OR U.S.A. and other countries. IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, FilterLab, Linear Active Thermistor, MXDEV, MXLAB, INCLUDING BUT NOT LIMITED TO ITS CONDITION, SEEVAL, SmartSensor and The Embedded Control Solutions QUALITY, PERFORMANCE, MERCHANTABILITY OR Company are registered trademarks of Microchip Technology FITNESS FOR PURPOSE. Microchip disclaims all liability Incorporated in the U.S.A. arising from this information and its use. Use of Microchip Analog-for-the-Digital Age, Application Maestro, CodeGuard, devices in life support and/or safety applications is entirely at dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN, the buyer’s risk, and the buyer agrees to defend, indemnify and ECONOMONITOR, FanSense, In-Circuit Serial hold harmless Microchip from any and all damages, claims, Programming, ICSP, ICEPIC, Mindi, MiWi, MPASM, MPLAB suits, or expenses resulting from such use. No licenses are Certified logo, MPLIB, MPLINK, mTouch, nanoWatt XLP, conveyed, implicitly or otherwise, under any Microchip PICkit, PICDEM, PICDEM.net, PICtail, PIC32 logo, PowerCal, intellectual property rights. PowerInfo, PowerMate, PowerTool, REAL ICE, rfLAB, Select Mode, Total Endurance, TSHARC, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. © 2009, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. Microchip received ISO/TS-16949:2002 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company’s quality system processes and procedures are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001:2000 certified. © 2009 Microchip Technology Inc. DS22147A-page 65

WORLDWIDE SALES AND SERVICE AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office Asia Pacific Office India - Bangalore Austria - Wels 2355 West Chandler Blvd. Suites 3707-14, 37th Floor Tel: 91-80-3090-4444 Tel: 43-7242-2244-39 Chandler, AZ 85224-6199 Tower 6, The Gateway Fax: 91-80-3090-4080 Fax: 43-7242-2244-393 Tel: 480-792-7200 Harbour City, Kowloon India - New Delhi Denmark - Copenhagen Fax: 480-792-7277 Hong Kong Tel: 91-11-4160-8631 Tel: 45-4450-2828 Technical Support: Tel: 852-2401-1200 Fax: 91-11-4160-8632 Fax: 45-4485-2829 http://support.microchip.com Web Address: Fax: 852-2401-3431 India - Pune France - Paris www.microchip.com Australia - Sydney Tel: 91-20-2566-1512 Tel: 33-1-69-53-63-20 Tel: 61-2-9868-6733 Fax: 33-1-69-30-90-79 Fax: 91-20-2566-1513 Atlanta Fax: 61-2-9868-6755 Germany - Munich Duluth, GA Japan - Yokohama China - Beijing Tel: 49-89-627-144-0 Tel: 678-957-9614 Tel: 81-45-471- 6166 Tel: 86-10-8528-2100 Fax: 49-89-627-144-44 Fax: 678-957-1455 Fax: 81-45-471-6122 Fax: 86-10-8528-2104 Italy - Milan Boston Korea - Daegu Westborough, MA China - Chengdu Tel: 82-53-744-4301 Tel: 39-0331-742611 Tel: 774-760-0087 Tel: 86-28-8665-5511 Fax: 82-53-744-4302 Fax: 39-0331-466781 Fax: 774-760-0088 Fax: 86-28-8665-7889 Korea - Seoul Netherlands - Drunen Chicago China - Hong Kong SAR Tel: 82-2-554-7200 Tel: 31-416-690399 Itasca, IL Tel: 852-2401-1200 Fax: 82-2-558-5932 or Fax: 31-416-690340 Tel: 630-285-0071 Fax: 852-2401-3431 82-2-558-5934 Spain - Madrid Fax: 630-285-0075 China - Nanjing Malaysia - Kuala Lumpur Tel: 34-91-708-08-90 Cleveland Tel: 86-25-8473-2460 Tel: 60-3-6201-9857 Fax: 34-91-708-08-91 Independence, OH Fax: 86-25-8473-2470 Fax: 60-3-6201-9859 UK - Wokingham Tel: 216-447-0464 China - Qingdao Malaysia - Penang Tel: 44-118-921-5869 Fax: 216-447-0643 Tel: 86-532-8502-7355 Tel: 60-4-227-8870 Fax: 44-118-921-5820 Dallas Fax: 86-532-8502-7205 Fax: 60-4-227-4068 Addison, TX China - Shanghai Philippines - Manila Tel: 972-818-7423 Tel: 86-21-5407-5533 Tel: 63-2-634-9065 Fax: 972-818-2924 Fax: 86-21-5407-5066 Fax: 63-2-634-9069 Detroit China - Shenyang Singapore Farmington Hills, MI Tel: 86-24-2334-2829 Tel: 65-6334-8870 Tel: 248-538-2250 Fax: 86-24-2334-2393 Fax: 65-6334-8850 Fax: 248-538-2260 China - Shenzhen Taiwan - Hsin Chu Kokomo Tel: 86-755-8203-2660 Tel: 886-3-6578-300 Kokomo, IN Fax: 86-755-8203-1760 Fax: 886-3-6578-370 Tel: 765-864-8360 Fax: 765-864-8387 China - Wuhan Taiwan - Kaohsiung Tel: 86-27-5980-5300 Tel: 886-7-536-4818 Los Angeles Fax: 86-27-5980-5118 Fax: 886-7-536-4803 Mission Viejo, CA Tel: 949-462-9523 China - Xiamen Taiwan - Taipei Fax: 949-462-9608 Tel: 86-592-2388138 Tel: 886-2-2500-6610 Fax: 86-592-2388130 Fax: 886-2-2508-0102 Santa Clara Santa Clara, CA China - Xian Thailand - Bangkok Tel: 408-961-6444 Tel: 86-29-8833-7252 Tel: 66-2-694-1351 Fax: 408-961-6445 Fax: 86-29-8833-7256 Fax: 66-2-694-1350 Toronto China - Zhuhai Mississauga, Ontario, Tel: 86-756-3210040 Canada Fax: 86-756-3210049 Tel: 905-673-0699 Fax: 905-673-6509 03/26/09 DS22147A-page 66 © 2009 Microchip Technology Inc.