MCP120/130 Microcontroller Supervisory Circuit with Open Drain Output FEATURES PACKAGES • Holds microcontroller in reset until supply voltage reaches stable operating level TO-92 with TO-92 WITH ‘D’ Bondout ‘F’ BONDOUT (cid:127) Resets microcontroller during power loss (cid:127) Precision monitoring of 3V, 3.3V and 5V systems (cid:127) 7 voltage trip points available (cid:127) Active low RESET pin RST VSS VSS VDD (cid:127) Open drain output VDD RST (cid:127) Internal pull-up resistor (5 k Ω) for MCP130 MCP120 MCP130 (cid:127) Holds RESET for 350 ms (typical) MCP130 (cid:127) RESET to VCC = 1.0V (cid:127) Accuracy of ±125 mV for 5V systems and ±75 mV TO-92 with TO-92 with for 3V systems over temperature ‘G’ Bondout ‘H’ Bondout (cid:127) 45 µA typical operating current (cid:127) Temperature range: - Industrial (I): -40°C to +85°C DESCRIPTION VDD RST VDD VSS VSS RST The Microchip Technology Inc. MCP120/130 is a volt- MCP120 MCP120 age supervisory device designed to keep a microcon- MCP130 troller in reset until the system voltage has reached the proper level and stabilized. It also operates as protec- tion from brown-out conditions when the supply voltage SOT-23-3 150mil SOIC drops below a safe operating level. Both devices are available with a choice of seven different trip voltages and both have open drain outputs. The MCP130 has an RST RVSDTD 12 87 NNCC internal 5kΩ pullup resistor. Both devices have active VDD VSS VNSCS 34 65 NNCC low RESET pins. The MCP120/130 will assert the RESET signal whenever the voltage on the VDD pin is MCP120 MCP120 below the trip-point voltage. MCP130 MCP130 BLOCK DIAGRAM VDD 5kΩ internal Comparator pull-up on MCP130 + Delay Output only - Circuit Driver RESET Bandgap Reference  2001 Microchip Technology Inc. DS11184D-page 1

MCP120/130 1.0 ELECTRICAL CHARACTERISTICS 1.1 Maximum Ratings* *Notice: Stresses above those listed under “Maximum Ratings” may cause permanent damage to the device. VDD........................................................................7.0V This is a stress rating only and functional operation of All inputs and outputs w.r.t. VSS.....-0.6V to VDD +1.0V the device at those or any other conditions above those Storage temperature..........................-65°C to +150°C indicated in the operational listings of this specification Ambient temp. with power applied.....-65°C to +125°C is not implied. Exposure to maximum rating conditions ESD protection on all pins.....................................≥ 2 kV for extended periods may affect device reliability. DC AND AC CHARACTERISTICS All parameters apply at the VDD = 1.0 - 5.5V specified temp and voltage Industrial (I): -40°C to +85°C ranges unless otherwise noted. Parameter Symbol Min. Typ. Max. Units Test Conditions Operating Voltage Range VDD 1.0 — 5.5 V VDD Value to RESET VDD 1.0 — — V MIN Operating Current IDD — 45 60 µA VDD = 5.5V (no load) VDD Trip Point MCP1X0-270 VTRIP 2.55 2.625 2.7 V MCP1X0-300 2.85 2.925 3.0 MCP1X0-315 3.0 3.075 3.15 MCP1X0-450 4.25 4.375 4.50 MCP1X0-460 4.35 4.475 4.60 MCP1X0-475 4.50 4.625 4.75 MCP1X0-485 4.60 4.725 4.85 RESET Low MCP1X0-270 VOL — — 0.4 V IOL = 3.2 mA, Level Output MCP1X0-300 VDD = VTRIP MIN Voltage MCP1X0-315 MCP1X0-450 — — 0.6 IOL = 8.5 mA, MCP1X0-460 VDD = VTRIP MIN MCP1X0-475 MCP1X0-485 RESET High MCP130-xxx VOH VDD-0.7 — — V IOH = 50 µA,VDD > VTRIP MAX Level Output (All VTRIP Voltage Points) (MCP130 Only) Pull-up Resistor (MCP130 Only) — 5 — kΩ Output Leakage (MCP120 Only) — 1 — µA Threshold Hysteresis VHYS — 50 — mV VDD Detect to RESET Inactive tRPU 150 350 700 ms VDD Detect to RESET tRPD — 10 — µs VDD ramped from VTRIPMAX + 250 mV down to VTRIPMIN - 250 mV Note: Typical values are for 25°C and VDD = 5.0V  2001 Microchip Technology Inc. DS11184D-page 2

MCP120/130 VTRIP VDD tRPU tRPD RESET VOH VOH Figure 1-1: MCP120/130 Timing Diagram  2001 Microchip Technology Inc. DS11184D-page 3

MCP120/130 2.0 APPLICATIONS INFORMATION 2.1 The Need for Supervisory Circuits For many of today’s microcontroller applications, care 5V must be taken to prevent low power conditions that can VTRIPMAX cause many different system problems. The most com- GE VTRIPMIN A mon causes are brown-out conditions where the sys- LT (VTRIPMIN - VDD) tem supply drops below the operating level momentar- VO ily, and the second, is when a slowly decaying power LY Transient supply causes the microcontroller to begin executing PP Duration U instructions without enough voltage to sustain SRAM S and producing indeterminate results. 0 TIME 0 VDD VDD Microcontroller VDD Bypass 10 MCP120 Capacitor TA = +25°C VSS MCLR µ)S 8 or N ( O RST RESET ATI 6 R U D NT 4 Tcurarvnes iweniltl sc aaubsoev ea trhees et E VSS SI N RA 2 Transients below T the curve will NOT cause a reset Figure 2-1: Typical Application 0 0 1 2 3 4 5 VTRIP - VDD (V) 2.2 Negative Going VDD Transients Many system designers implementing POR circuits are Figure 2-2: Typical Transient Response concerned about the minimum pulse width required to cause a reset. Figure2-2 shows typical transient voltage below the trip point (VTRIP - VDD) vs. transient duration. It shows that the farther below the trip point the transient pulse goes, the duration of the pulse required to cause a reset gets shorter. A 0.1 µF bypass cap mounted as close as possible to the VDD pin pro- vides additional transient immunity. DS11184D-page 4  2001 Microchip Technology Inc.

MCP120/130 2.3 Effect of Temperature on Timeout Period (tRPU) 1.002 The timeout period (tRPU) determines how long the )RIP T 1.000 device remains in the reset condition. This is controlled V by an internal RC timer and is effected by both VDD D* ( L 0.998 and temperature. The graph shown in Figure2-3 O H shows typical response for different VDD values and ES R 0.996 temperatures. H T D E 0.994 Z LI 700 A M 0.992 R O s) 600 N m 0.997 ) (U VDD = 6V -40 -20 0 20 40 60 80 100 P 500 TEMPERATURE (°C) R D (t VDD = 5V * Multiply value at 25°C by this RIO 400 fteamctopre troa tdueretermine the value at E P T 300 OU VDD = 4V Figure 2-5: Normalized VTRIP vs. Temperature E TIM 200 VDD = 3V 100 800 -40 -20 0 20 40 60 80 100 VDD = 2.5V TEMPERATURE (°C) 700 VDD = 1.5V VDD = 3.5V 600 Figure 2-3: tRPU vs. Temperature 500 V) m (L 400 VO VDD = 4.5V 60 300 VDD = 5V 200 A) 50 VDD = 5.5V µ T ( 100 N 40 TA = +25°C RE 0 R 0 2 4 6 8 10 12 14 16 18 20 U G C 30 VDD = 3V IOL (mA) N VDD = 4V TI 20 RA Figure 2-6: VOL vs. IOL E P O 10 1.3 0 -40 -20 0 20 40 60 80 100 TEMPERATURE (°C) 1.2 Figure 2-4: IDD vs. Temperature D I* OL 1.1 E Z1.00 LI A M R 0.9 O N 0.8 0.7 -40 -20 0 20 40 60 80 100 TEMPERATURE (°C) * Multiply value at 25°C by this factor to determine the value at temperature Figure 2-7: Normalized IOL vs. Temperature  2001 Microchip Technology Inc. DS11184D-page 5

MCP120/130 3.0 PACKAGING INFORMATION 3.1 Package Marking Information 3-Lead Plastic Transistor Outline (TO-92) Example: XXXXXX MCP120 XXXXXX XXXXXX XXXXXX XXXXXX YWWNNN YWWNNN 8-Lead Plastic Small Outline (SOIC) Example: XXXXXXXX MCP120 XXXXYYWW XXXXYYWW NNN NNN 3-Lead Plastic Small Outline Transistor (SOT23) Example: XXNN PKNN SOT23 PARTS LABELING: The table below identifies the first 2 characters (XX) in the 4-character field (XXNN) for marking of the 3-Lead SOT23 package. Mark Part Number Mark Part Number SJ MCP120T-270I/TT PJ MCP130T-270I/TT SK MCP120T-300I/TT PK MCP130T-300I/TT SL MCP120T-315I/TT PL MCP130T-315I/TT SM MCP120T-450I/TT PM MCP130T-450I/TT SN MCP120T-460I/TT PN MCP130T-460I/TT SO MCP120T-475I/TT PO MCP130T-475I/TT SP MCP120T-485I/TT PP MCP130T-485I/TT Legend: XX...X Customer specific information* YY Year code (last 2 digits of calendar year) WW Week code (week of January 1 is week ‘01’) NNN Alphanumeric traceability code Note: In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line thus limiting the number of available characters for customer specific information. * Standard OTP marking consists of Microchip part number, year code, week code, and traceability code. For OTP marking beyond this, certain price adders apply. Please check with your Microchip Sales Office. For QTP devices, any special marking adders are included in QTP price. DS11184D-page 6  2001 Microchip Technology Inc.

MCP120/130 3.2 Package Detail Information 3-Lead Plastic Transistor Outline (TO) (TO-92) E1 D 1 n L 1 2 3 α B p c A R β Units INCHES* MILLIMETERS Dimension Limits MIN NOM MAX MIN NOM MAX Number of Pins n 3 3 Pitch p .050 1.27 Bottom to Package Flat A .130 .143 .155 3.30 3.62 3.94 Overall Width E1 .175 .186 .195 4.45 4.71 4.95 Overall Length D .170 .183 .195 4.32 4.64 4.95 Molded Package Radius R .085 .090 .095 2.16 2.29 2.41 Tip to Seating Plane L .500 .555 .610 12.70 14.10 15.49 Lead Thickness c .014 .017 .020 0.36 0.43 0.51 Lead Width B .016 .019 .022 0.41 0.48 0.56 Mold Draft Angle Top α 4 5 6 4 5 6 Mold Draft Angle Bottom β 2 3 4 2 3 4 *Controlling Parameter Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010” (0.254mm) per side. JEDEC Equivalent: TO-92 Drawing No. C04-101  2001 Microchip Technology Inc. DS11184D-page 7

MCP120/130 3-Lead Plastic Small Outline Transistor (TT) (SOT23) E E1 2 B p1 D n p 1 α c A A2 φ A1 β L Units INCHES* MILLIMETERS Dimension Limits MIN NOM MAX MIN NOM MAX Number of Pins n 3 3 Pitch p .038 0.96 Outside lead pitch (basic) p1 .076 1.92 Overall Height A .035 .040 .044 0.89 1.01 1.12 Molded Package Thickness A2 .035 .037 .040 0.88 0.95 1.02 Standoff § A1 .000 .002 .004 0.01 0.06 0.10 Overall Width E .083 .093 .104 2.10 2.37 2.64 Molded Package Width E1 .047 .051 .055 1.20 1.30 1.40 Overall Length D .110 .115 .120 2.80 2.92 3.04 Foot Length L .014 .018 .022 0.35 0.45 0.55 Foot Angle φ 0 5 10 0 5 10 Lead Thickness c .004 .006 .007 0.09 0.14 0.18 Lead Width B .015 .017 .020 0.37 0.44 0.51 Mold Draft Angle Top α 0 5 10 0 5 10 Mold Draft Angle Bottom β 0 5 10 0 5 10 * Controlling Parameter § Significant Characteristic Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010” (0.254mm) per side. JEDEC Equivalent: TO-236 Drawing No. C04-104 DS11184D-page 8  2001 Microchip Technology Inc.

MCP120/130 8-Lead Plastic Small Outline (SN) –Narrow, 150 mil (SOIC E E1 p D 2 B n 1 h α 45° c A A2 φ β L A1 Units INCHES* MILLIMETERS Dimension Limits MIN NOM MAX MIN NOM MAX Number of Pins n 8 8 Pitch p .050 1.27 Overall Height A .053 .061 .069 1.35 1.55 1.75 Molded Package Thickness A2 .052 .056 .061 1.32 1.42 1.55 Standoff § A1 .004 .007 .010 0.10 0.18 0.25 Overall Width E .228 .237 .244 5.79 6.02 6.20 Molded Package Width E1 .146 .154 .157 3.71 3.91 3.99 Overall Length D .189 .193 .197 4.80 4.90 5.00 Chamfer Distance h .010 .015 .020 0.25 0.38 0.51 Foot Length L .019 .025 .030 0.48 0.62 0.76 Foot Angle φ 0 4 8 0 4 8 Lead Thickness c .008 .009 .010 0.20 0.23 0.25 Lead Width B .013 .017 .020 0.33 0.42 0.51 Mold Draft Angle Top α 0 12 15 0 12 15 Mold Draft Angle Bottom β 0 12 15 0 12 15 * Controlling Parameter § Significant Characteristic Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010” (0.254mm) per side. JEDEC Equivalent: MS-012 Drawing No. C04-057  2001 Microchip Technology Inc. DS11184D-page 9

MCP120/130 ON-LINE SUPPORT Systems Information and Upgrade Hot Line The Systems Information and Upgrade Line provides Microchip provides on-line support on the Microchip system users a listing of the latest versions of all of World Wide Web (WWW) site. Microchip's development systems software products. The web site is used by Microchip as a means to make Plus, this line provides information on how customers files and information easily available to customers. To can receive any currently available upgrade kits.The view the site, the user must have access to the Internet Hot Line Numbers are: and a web browser, such as Netscape or Microsoft 1-800-755-2345 for U.S. and most of Canada, and Explorer. Files are also available for FTP download from our FTP site. 1-480-792-7302 for the rest of the world. Connecting to the Microchip Internet Web Site The Microchip web site is available by using your favorite Internet browser to attach to: www.microchip.com The file transfer site is available by using an FTP ser- vice to connect to: ftp://ftp.microchip.com The web site and file transfer site provide a variety of services. Users may download files for the latest Development Tools, Data Sheets, Application Notes, User’s Guides, Articles and Sample Programs. A vari- ety of Microchip specific business information is also available, including listings of Microchip sales offices, distributors and factory representatives. Other data available for consideration is: (cid:127) Latest Microchip Press Releases (cid:127) Technical Support Section with Frequently Asked Questions (cid:127) Design Tips (cid:127) Device Errata (cid:127) Job Postings (cid:127) Microchip Consultant Program Member Listing (cid:127) Links to other useful web sites related to Microchip Products (cid:127) Conferences for products, Development Systems, technical information and more (cid:127) Listing of seminars and events DS11184D-page 10  2001 Microchip Technology Inc.

MCP120/130 READER RESPONSE It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip prod- uct. If you wish to provide your comments on organization, clarity, subject matter, and ways in which our documentation can better serve you, please FAX your comments to the Technical Publications Manager at (480) 792-7578. Please list the following information, and use this outline to provide us with your comments about this Data Sheet. To: Technical Publications Manager Total Pages Sent RE: Reader Response From: Name Company Address City / State / ZIP / Country Telephone: (_______) _________ - _________ FAX: (______) _________ - _________ Application (optional): Would you like a reply? Y N Device: MCP120/130 Literature Number: DS11184D Questions: 1. What are the best features of this document? 2. How does this document meet your hardware and software development needs? 3. Do you find the organization of this data sheet easy to follow? If not, why? 4. What additions to the data sheet do you think would enhance the structure and subject? 5. What deletions from the data sheet could be made without affecting the overall usefulness? 6. Is there any incorrect or misleading information (what and where)? 7. How would you improve this document? 8. How would you improve our software, systems, and silicon products?  2001 Microchip Technology Inc. DS11184D-page 11

MCP120/130 NOTES: DS11184D-page 12  2001 Microchip Technology Inc.

MCP120/130 NOTES:  2001 Microchip Technology Inc. DS11184D-page 13

MCP120/130 PRODUCT IDENTIFICATION SYSTEM To order or to obtain information (e.g., on pricing or delivery), please refer to the factory or the listed sales offices. PART NO. X X X /XX Examples: Device RESET/ Bondout Temperature Package a) MCP120–270I/SN = VTRIP range of 2.55V - RESET Option Range 2.70V, Industrial Temp., SOIC package VTRIP Voltage b) MCP120–300DI/TO = VTRIP range of 2.85V- 3.00V, Bonding Option D, Industrial Temp., TO-92 package Device: MCP120: Supervisor circuit with open drain output MCP120T: Supervisor circuit with open drain output c) MCP120T–315I/TT = VTRIP range of 3.00V- (tape & reel) 3.15V, Industrial Temp., SOT-23 package MCP130: Supervisor circuit with open drain output and d) MCP130–450I/SN = VTRIP range of 4.25V - internal pull-up resistor 4.50V, Industrial Temp., SOIC package MCP130T: Supervisor circuit with open drain output and internal pull-up resistor (tape & reel) e) MCP130–460FI/TO = VTRIP range of 4.35V- 4.60V, Bonding Option F, Industrial Temp., TO-92 package RESET/RESET VTRIP 270 = 2.55 ≤ VTRIP ≤ 2.70 Voltage 300 = 2.85 ≤ VTRIP ≤ 3.00 f) MCP130T–475I/TT = Tape & Reel, VTRIP 315 = 3.00 ≤ VTRIP ≤ 3.15 range of 4.50V - 4.75V, Industrial Temp., 450 = 4.25 ≤ VTRIP ≤ 4.50 SOT-23 package 460 = 4.35 ≤ VTRIP ≤ 4.60 475 = 4.50 ≤ VTRIP ≤ 4.75 TO-92 with TO-92 with 485 = 4.60 ≤ VTRIP ≤ 4.85 ‘D’ Bondout ‘F’ Bondout Bondout Option: D = D Bond Option (see bond option chart) (TO-92 Only) F = F Bond Option G = G Bond Option H = H Bond Option RST VSS VSS VDD VDD RST Temperature Range: I = -40°C to +85°C (only offered in I) MCP120 MCP130 MCP130 Package: SN = SOIC (8-lead, 150 mil body) TO = TO-92 (3-lead) [offered in bags only] TO-92 with TO-92 with TT = SOT-23 (3-lead) [offered in tape & reel only] ‘G’ Bondout ‘H’ Bondout VDD RST VDD VSS VSS RST MCP120 MCP120 MCP130 Sales and Support Data Sheets Products supported by a preliminary Data Sheet may have an errata sheet describing minor operational differences and recom- mended workarounds. To determine if an errata sheet exists for a particular device, please contact one of the following: 1. Your local Microchip sales office 2. The Microchip Corporate Literature Center U.S. FAX: (480) 792-7277 3. The Microchip Worldwide Site (www.microchip.com) Please specify which device, revision of silicon and Data Sheet (include Literature #) you are using. New Customer Notification System Register on our web site (www.microchip.com/cn) to receive the most current information on our products. DS11184D-page 14  2001 Microchip Technology Inc.

MCP120/130 “All rights reserved. Copyright © 2001, Microchip Trademarks Technology Incorporated, USA. Information contained in this publication regarding device applications and the The Microchip name, logo, PIC, PICmicro, like is intended through suggestion only and may be PICMASTER, PICSTART, PRO MATE, KEELOQ, superseded by updates. No representation or warranty SEEVAL, MPLAB and The Embedded Control is given and no liability is assumed by Microchip Solutions Company are registered trademarks of Technology Incorporated with respect to the accuracy Microchip Technology Incorporated in the U.S.A. and or use of such information, or infringement of patents or other countries. other intellectual property rights arising from such use Total Endurance, ICSP, In-Circuit Serial Programming, or otherwise. Use of Microchip’s products as critical FilterLab, MXDEV, microID, FlexROM, fuzzyLAB, components in life support systems is not authorized MPASM, MPLINK, MPLIB, PICDEM, ICEPIC, except with express written approval by Microchip. No Migratable Memory, FanSense, ECONOMONITOR, licenses are conveyed, implicitly or otherwise, under SelectMode and microPort are trademarks of any intellectual property rights. The Microchip logo and Microchip Technology Incorporated in the U.S.A. name are registered trademarks of Microchip Technology Inc. in the U.S.A. and other countries. All Serialized Quick Term Programming (SQTP) is a rights reserved. All other trademarks mentioned herein service mark of Microchip Technology Incorporated in are the property of their respective companies. No the U.S.A. licenses are conveyed, implicitly or otherwise, under any intellectual property rights.” All other trademarks mentioned herein are property of their respective companies. © 2001, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Microchip received QS-9000 quality system certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona in July 1999. The Company’s quality system processes and procedures are QS-9000 compliant for its PICmicro® 8-bit MCUs, KEELOQ® code hopping devices, Serial EEPROMs and microperipheral products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001 certified.  2001 Microchip Technology Inc. DS11184D-page 15

WORLDWIDE SALES AND SERVICE AMERICAS New York ASIA/PACIFIC (continued) Corporate Office 150 Motor Parkway, Suite 202 Korea Hauppauge, NY 11788 2355 West Chandler Blvd. Microchip Technology Korea Tel: 631-273-5305 Fax: 631-273-5335 Chandler, AZ 85224-6199 168-1, Youngbo Bldg. 3 Floor San Jose Tel: 480-792-7200 Fax: 480-792-7277 Samsung-Dong, Kangnam-Ku Technical Support: 480-792-7627 Microchip Technology Inc. Seoul, Korea Web Address: http://www.microchip.com 2107 North First Street, Suite 590 Tel: 82-2-554-7200 Fax: 82-2-558-5934 Rocky Mountain San Jose, CA 95131 Singapore Tel: 408-436-7950 Fax: 408-436-7955 2355 West Chandler Blvd. Microchip Technology Singapore Pte Ltd. Toronto Chandler, AZ 85224-6199 200 Middle Road Tel: 480-792-7966 Fax: 480-792-7456 6285 Northam Drive, Suite 108 #07-02 Prime Centre Atlanta Mississauga, Ontario L4V 1X5, Canada Singapore, 188980 500 Sugar Mill Road, Suite 200B Tel: 905-673-0699 Fax: 905-673-6509 Tel: 65-334-8870 Fax: 65-334-8850 Atlanta, GA 30350 Taiwan Tel: 770-640-0034 Fax: 770-640-0307 ASIA/PACIFIC Microchip Technology Taiwan Austin 11F-3, No. 207 Analog Product Sales Australia Tung Hua North Road 8303 MoPac Expressway North Microchip Technology Australia Pty Ltd Taipei, 105, Taiwan Suite A-201 Suite 22, 41 Rawson Street Tel: 886-2-2717-7175 Fax: 886-2-2545-0139 Austin, TX 78759 Epping 2121, NSW Tel: 512-345-2030 Fax: 512-345-6085 Australia Boston Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 EUROPE 2 Lan Drive, Suite 120 China - Beijing Denmark Westford, MA 01886 Microchip Technology Beijing Office Microchip Technology Denmark ApS Tel: 978-692-3848 Fax: 978-692-3821 Unit 915 Regus Business Centre Boston New China Hong Kong Manhattan Bldg. Lautrup hoj 1-3 Analog Product Sales No. 6 Chaoyangmen Beidajie Ballerup DK-2750 Denmark Unit A-8-1 Millbrook Tarry Condominium Beijing, 100027, No. China Tel: 45 4420 9895 Fax: 45 4420 9910 97 Lowell Road Tel: 86-10-85282100 Fax: 86-10-85282104 France China - Shanghai Concord, MA 01742 Arizona Microchip Technology SARL Tel: 978-371-6400 Fax: 978-371-0050 Microchip Technology Shanghai Office Parc d’Activite du Moulin de Massy Chicago Room 701, Bldg. B 43 Rue du Saule Trapu 333 Pierce Road, Suite 180 Far East International Plaza Batiment A - ler Etage Itasca, IL 60143 No. 317 Xian Xia Road 91300 Massy, France Tel: 630-285-0071 Fax: 630-285-0075 Shanghai, 200051 Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Dallas Tel: 86-21-6275-5700 Fax: 86-21-6275-5060 Germany Hong Kong 4570 Westgrove Drive, Suite 160 Arizona Microchip Technology GmbH Addison, TX 75001 Microchip Asia Pacific Gustav-Heinemann Ring 125 Tel: 972-818-7423 Fax: 972-818-2924 RM 2101, Tower 2, Metroplaza D-81739 Munich, Germany Dayton 223 Hing Fong Road Tel: 49-89-627-144 0 Fax: 49-89-627-144-44 Kwai Fong, N.T., Hong Kong Germany Two Prestige Place, Suite 130 Tel: 852-2401-1200 Fax: 852-2401-3431 Miamisburg, OH 45342 India Analog Product Sales Tel: 937-291-1654 Fax: 937-291-9175 Lochhamer Strasse 13 Detroit Microchip Technology Inc. D-82152 Martinsried, Germany India Liaison Office Tel: 49-89-895650-0 Fax: 49-89-895650-22 Tri-Atria Office Building Divyasree Chambers Italy 32255 Northwestern Highway, Suite 190 1 Floor, Wing A (A3/A4) Farmington Hills, MI 48334 No. 11, O’Shaugnessey Road Arizona Microchip Technology SRL Tel: 248-538-2250 Fax: 248-538-2260 Bangalore, 560 025, India Centro Direzionale Colleoni Los Angeles Tel: 91-80-2290061 Fax: 91-80-2290062 Palazzo Taurus 1 V. Le Colleoni 1 20041 Agrate Brianza 18201 Von Karman, Suite 1090 Japan Milan, Italy Irvine, CA 92612 Microchip Technology Intl. Inc. Tel: 39-039-65791-1 Fax: 39-039-6899883 Tel: 949-263-1888 Fax: 949-263-1338 Benex S-1 6F United Kingdom Mountain View 3-18-20, Shinyokohama Arizona Microchip Technology Ltd. Analog Product Sales Kohoku-Ku, Yokohama-shi 505 Eskdale Road 1300 Terra Bella Avenue Kanagawa, 222-0033, Japan Winnersh Triangle Mountain View, CA 94043-1836 Tel: 81-45-471- 6166 Fax: 81-45-471-6122 Wokingham Tel: 650-968-9241 Fax: 650-967-1590 Berkshire, England RG41 5TU Tel: 44 118 921 5869 Fax: 44-118 921-5820 01/30/01 All rights reserved. © 2001 Microchip Technology Incorporated. Printed in the USA. 2/01 Printed on recycled paper. Information contained in this publication regarding device applications and the like is intended through suggestion only and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. No representation or warranty is given and no liability is assumed by Microchip Technology Incorporated with respect to the accuracy or use of such information, or infringement of patents or other intellectual property rights arising from such use or otherwise. Use of Microchip’s products as critical components in life support systems is not authorized except with express written approval by Microchip. No licenses are conveyed, implicitly or otherwise, except as maybe explicitly expressed herein, under any intellec- tual property rights. The Microchip logo and name are registered trademarks of Microchip Technology Inc. in the U.S.A. and other countries. All rights reserved. All other trademarks mentioned herein are the property of their respective companies. DS11184D-page 16  2001 Microchip Technology Inc.

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: M icrochip: MCP120-270I/SN MCP130-270DI/TO MCP130-450DI/TO MCP130T-485I/TT MCP130-460DI/TO MCP130T- 485I/SN MCP130-300DI/TO MCP120T-270I/SN MCP130-485FI/TO MCP120T-315I/SN MCP120T-300I/SN MCP130-450I/SN MCP120T-300I/TT MCP120T-315I/TT MCP130T-300I/SN MCP130T-460I/SN MCP120-485HI/TO MCP130T-460I/TT MCP120T-270I/TT MCP130-300I/SN MCP120-450I/SN MCP130T-450I/SN MCP120-485I/SN MCP130T-450I/TT MCP130T-300I/TT MCP130-485DI/TO MCP120-475DI/TO MCP120T-450I/TT MCP120-315DI/TO MCP120T-450I/SN MCP130-475HI/TO MCP130-315HI/TO MCP120-300DI/TO MCP120-460DI/TO MCP120- 450DI/TO MCP120-460I/SN MCP130-475FI/TO MCP130-315FI/TO MCP130-460HI/TO MCP130-270HI/TO MCP130-300HI/TO MCP130-450HI/TO MCP120T-460I/TT MCP120-475I/SN MCP130-315I/SN MCP130T-475I/TT MCP130T-475I/SN MCP130-300FI/TO MCP130-460FI/TO MCP130-270FI/TO MCP130-450FI/TO MCP130- 475DI/TO MCP130-475I/SN MCP120-270DI/TO MCP120T-485I/TT MCP120T-485I/SN MCP130T-315I/SN MCP130T-315I/TT MCP120-485GI/TO MCP130T-270I/SN MCP120T-460I/SN MCP120-300GI/TO MCP120- 270GI/TO MCP120-450GI/TO MCP120-460GI/TO MCP130T-270I/TT MCP120T-475I/TT MCP130-485HI/TO MCP120T-475I/SN MCP120-270HI/TO MCP120-450HI/TO MCP120-300HI/TO MCP120-460HI/TO MCP130-485I/SN MCP130-270I/SN MCP120-485DI/TO MCP130-315DI/TO MCP120-300I/SN MCP120-475HI/TO MCP120-315HI/TO MCP130-460I/SN MCP120-315I/SN MCP120-315GI/TO MCP120-475GI/TO