MC9S08JM60 MC9S08JM32 Data Sheet HCS08 Microcontrollers MC9S08JM60 Rev. 5 10/2014 freescale.com

None

MC9S08JM60 Series Features 8-Bit HCS08 Central Processor Unit (CPU) (cid:129) SPI — Two 8- or 16-bit selectable serial peripheral • 48-MHz HCS08 CPU (central processor unit) interface modules with a receive data buffer hardware match function (cid:129) 24-MHz internal bus frequency (cid:129) IIC — Inter-integrated circuit bus module to (cid:129) HC08 instruction set with added BGND instruction operate at up to 100 kbps with maximum bus (cid:129) Background debugging system loading; multi-master operation; programmable (cid:129) Breakpoint capability to allow single breakpoint slave address; interrupt-driven byte-by-byte data setting during in-circuit debugging (plus two more transfer; 10-bit addressing and broadcast modes breakpoints in on-chip debug module) support (cid:129) In-circuit emulator (ICE) debug module containing (cid:129) Timers — One 2-channel and one 6-channel two comparators and nine trigger modes. Eight 16-bit timer/pulse-width modulator (TPM) deep FIFO for storing change-of-flow addresses modules: Selectable input capture, output and event-only data. Debug module supports both compare, and edge-aligned PWM capability on tag and force breakpoints. each channel. Each timer module may be (cid:129) Support for up to 32 interrupt/reset sources configured for buffered, centered PWM (CPWM) on all channels Memory Options (cid:129) KBI — 8-pin keyboard interrupt module (cid:129) Up to 60 KB of on-chip in-circuit programmable (cid:129) RTC — Real-time counter with binary- or flash memory with block protection and security decimal-based prescaler options (cid:129) Up to 4 KB of on-chip RAM Input/Output (cid:129) 256 bytes of USB RAM (cid:129) Up to 51 general-purpose input/output pins (cid:129) Software selectable pullups on ports when used Clock Source Options as inputs (cid:129) Clock source options include crystal, resonator, (cid:129) Software selectable slew rate control on ports external clock when used as outputs (cid:129) MCG (multi-purpose clock generator) — PLL and (cid:129) Software selectable drive strength on ports when FLL; internal reference clock with trim adjustment used as outputs System Protection (cid:129) Master reset pin and power-on reset (POR) (cid:129) Optional computer operating properly (COP) reset (cid:129) Internal pullup on RESET, IRQ, and BKGD/MS with option to run from independent 1-kHz internal pins to reduce customer system cost clock source or the bus clock Package Options (cid:129) Low-voltage detection with reset or interrupt (cid:129) 64-pin quad flat package (QFP) (cid:129) Illegal opcode detection with reset (cid:129) 64-pin low-profile quad flat package (LQFP) (cid:129) Illegal address detection with reset (cid:129) 48-pin quad flat no-lead (QFN) Power-Saving Modes (cid:129) 44-pin low-profile quad flat package (LQFP) (cid:129) Wait plus two stops Peripherals (cid:129) USB — USB 2.0 full-speed (12 Mbps) device controller with dedicated on-chip USB transceiver, 3.3-V regulator and USBDP pull-up resister; supports control, interrupt, isochronous, and bulk transfers; supports endpoint 0 and up to 6 additional endpoints; endpoints 5 and 6 can be combined to provide double buffering capability (cid:129) ADC — 12-channel, 12-bit analog-to-digital converter with automatic compare function; internal temperature sensor (cid:129) ACMP — Analog comparator with option to compare to internal reference; operation in stop3 mode (cid:129) SCI — Two serial communications interface modules with optional 13-bit break LIN extensions

None

MC9S08JM60 Series Data Sheet Covers MC9S08JM60 MC9S08JM32 MC9S08JM60 Rev. 5 10/2014

Revision History To provide the most up-to-date information, the revision of our documents on the World Wide Web will be the most current. Your printed copy may be an earlier revision. To verify you have the latest information available, refer to: http://freescale.com/ The following revision history table summarizes changes contained in this document. Revision Revision Description of Changes Number Date 1 11/27/2007 Initial release Changed the location of R to connect to EXTALin Figure2-4. S Changed port rise and fall time in TableA-13. Added DC injection current and RAM retention voltage in TableA-6. 2 3/4/2008 Deleted note on 625 ns of item 17 in TableA-12. Moved Bandgap Voltage Reference item from TableA-8 to TableA-6. Added one paragraph on how to improve accuracy to Section10.1.1.5, “Temperature Sensor.” Changed the V from 1.396 mV to 1.396 V in TableA-10. TEMP25 3 1/21/2009 Complete the EMC data in SectionA.15, “EMC Performance.” Revised the Typo in Table11-4. 4 2/21/2010 Changed the location of R to connect to XTALin Figure2-4. S 5 10/2014 Updated t in TableA-13. LPO This product incorporates SuperFlash® technology licensed from SST. Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc. ©Freescale Semiconductor, Inc., 2007-2014. All rights reserved.

List of Chapters Chapter Number Title Page Chapter 1 Device Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Chapter 2 Pins and Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 Chapter 3 Modes of Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 Chapter 4 Memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 Chapter 5 Resets, Interrupts, and System Configuration . . . . . . . . . . . . . . .65 Chapter 6 Parallel Input/Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81 Chapter 7 Central Processor Unit (S08CPUV2) . . . . . . . . . . . . . . . . . . . . . . .99 Chapter 8 5 V Analog Comparator (S08ACMPV2) . . . . . . . . . . . . . . . . . . . .119 Chapter 9 Keyboard Interrupt (S08KBIV2) . . . . . . . . . . . . . . . . . . . . . . . . . .125 Chapter 10 Analog-to-Digital Converter (S08ADC12V1) . . . . . . . . . . . . . . .133 Chapter 11 Inter-Integrated Circuit (S08IICV2) . . . . . . . . . . . . . . . . . . . . . . .159 Chapter 12 Multi-Purpose Clock Generator (S08MCGV1) . . . . . . . . . . . . . .179 Chapter 13 Real-Time Counter (S08RTCV1) . . . . . . . . . . . . . . . . . . . . . . . . .211 Chapter 14 Serial Communications Interface (S08SCIV4). . . . . . . . . . . . . .221 Chapter 15 16-Bit Serial Peripheral Interface (S08SPI16V1) . . . . . . . . . . . .241 Chapter 16 Timer/Pulse-Width Modulator (S08TPMV3) . . . . . . . . . . . . . . . .269 Chapter 17 Universal Serial Bus Device Controller (S08USBV1) . . . . . . . .293 Chapter 18 Development Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .325 Appendix A Electrical Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 347 Appendix B Ordering Information and Mechanical Drawings. . . . . . . . . . 371 MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 7

None

Contents Section Number Title Page Chapter 1 Device Overview 1.1 Introduction .....................................................................................................................................19 1.2 MCU Block Diagram ......................................................................................................................19 1.3 System Clock Distribution ..............................................................................................................21 Chapter 2 Pins and Connections 2.1 Introduction .....................................................................................................................................25 2.2 Device Pin Assignment ...................................................................................................................26 2.3 Recommended System Connections ...............................................................................................28 2.3.1 Power (V , V , V , V , V , V ) ....................................................30 DD SS SSOSC DDAD SSAD USB33 2.3.2 Oscillator (XTAL, EXTAL) ..............................................................................................30 2.3.3 RESET Pin ........................................................................................................................31 2.3.4 Background/Mode Select (BKGD/MS) ............................................................................31 2.3.5 ADC Reference Pins (V , V ) .............................................................................31 REFH REFL 2.3.6 External Interrupt Pin (IRQ) .............................................................................................31 2.3.7 USB Data Pins (USBDP, USBDN) ...................................................................................32 2.3.8 General-Purpose I/O and Peripheral Ports ........................................................................32 Chapter 3 Modes of Operation 3.1 Introduction .....................................................................................................................................35 3.2 Features ...........................................................................................................................................35 3.3 Run Mode ........................................................................................................................................35 3.4 Active Background Mode ...............................................................................................................35 3.5 Wait Mode .......................................................................................................................................36 3.6 Stop Modes ......................................................................................................................................37 3.6.1 Stop3 Mode .......................................................................................................................37 3.6.2 Stop2 Mode .......................................................................................................................38 3.6.3 On-Chip Peripheral Modules in Stop Modes ....................................................................39 Chapter 4 Memory 4.1 MC9S08JM60 Series Memory Map ...............................................................................................41 4.1.1 Reset and Interrupt Vector Assignments ...........................................................................42 4.2 Register Addresses and Bit Assignments ........................................................................................43 4.3 RAM (System RAM) ......................................................................................................................50 4.4 USB RAM .......................................................................................................................................51 MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 9

4.5 Flash ................................................................................................................................................51 4.5.1 Features .............................................................................................................................51 4.5.2 Program and Erase Times .................................................................................................52 4.5.3 Program and Erase Command Execution .........................................................................52 4.5.4 Burst Program Execution ..................................................................................................54 4.5.5 Access Errors ....................................................................................................................55 4.5.6 Flash Block Protection ......................................................................................................56 4.5.7 Vector Redirection ............................................................................................................57 4.6 Security ............................................................................................................................................57 4.7 Flash Registers and Control Bits .....................................................................................................58 4.7.1 Flash Clock Divider Register (FCDIV) ............................................................................59 4.7.2 Flash Options Register (FOPT and NVOPT) ....................................................................60 4.7.3 Flash Configuration Register (FCNFG) ...........................................................................61 4.7.4 Flash Protection Register (FPROT and NVPROT) ..........................................................61 4.7.5 Flash Status Register (FSTAT) ..........................................................................................62 4.7.6 Flash Command Register (FCMD) ...................................................................................63 Chapter 5 Resets, Interrupts, and System Configuration 5.1 Introduction .....................................................................................................................................65 5.2 Features ...........................................................................................................................................65 5.3 MCU Reset ......................................................................................................................................65 5.4 Computer Operating Properly (COP) Watchdog .............................................................................66 5.5 Interrupts .........................................................................................................................................67 5.5.1 Interrupt Stack Frame .......................................................................................................68 5.5.2 External Interrupt Request (IRQ) Pin ...............................................................................68 5.5.3 Interrupt Vectors, Sources, and Local Masks ...................................................................69 5.6 Low-Voltage Detect (LVD) System ................................................................................................71 5.6.1 Power-On Reset Operation ...............................................................................................71 5.6.2 Low-Voltage Detection (LVD) Reset Operation ...............................................................71 5.6.3 Low-Voltage Warning (LVW) Interrupt Operation ...........................................................71 5.7 Reset, Interrupt, and System Control Registers and Control Bits ...................................................72 5.7.1 Interrupt Pin Request Status and Control Register (IRQSC) ............................................72 5.7.2 System Reset Status Register (SRS) .................................................................................73 5.7.3 System Background Debug Force Reset Register (SBDFR) ............................................74 5.7.4 System Options Register 1 (SOPT1) ................................................................................74 5.7.5 System Options Register 2 (SOPT2) ................................................................................76 5.7.6 System Device Identification Register (SDIDH, SDIDL) ................................................76 5.7.7 System Power Management Status and Control 1 Register (SPMSC1) ...........................77 5.7.8 System Power Management Status and Control 2 Register (SPMSC2) ...........................78 Chapter 6 Parallel Input/Output 6.1 Introduction .....................................................................................................................................81 6.2 Port Data and Data Direction ..........................................................................................................81 MC9S08JM60 Series Data Sheet, Rev. 5 10 Freescale Semiconductor

6.3 Pin Control ......................................................................................................................................82 6.3.1 Internal Pullup Enable ......................................................................................................83 6.3.2 Output Slew Rate Control Enable .....................................................................................83 6.3.3 Output Drive Strength Select ............................................................................................83 6.4 Pin Behavior in Stop Modes ............................................................................................................83 6.5 Parallel I/O and Pin Control Registers ............................................................................................83 6.5.1 Port A I/O Registers (PTAD and PTADD) ........................................................................84 6.5.2 Port A Pin Control Registers (PTAPE, PTASE, PTADS) .................................................84 6.5.3 Port B I/O Registers (PTBD and PTBDD) ........................................................................86 6.5.4 Port B Pin Control Registers (PTBPE, PTBSE, PTBDS) .................................................86 6.5.5 Port C I/O Registers (PTCD and PTCDD) ........................................................................88 6.5.6 Port C Pin Control Registers (PTCPE, PTCSE, PTCDS) .................................................88 6.5.7 Port D I/O Registers (PTDD and PTDDD) .......................................................................90 6.5.8 Port D Pin Control Registers (PTDPE, PTDSE, PTDDS) ................................................90 6.5.9 Port E I/O Registers (PTED and PTEDD) ........................................................................92 6.5.10 Port E Pin Control Registers (PTEPE, PTESE, PTEDS) ..................................................92 6.5.11 Port F I/O Registers (PTFD and PTFDD) .........................................................................94 6.5.12 Port F Pin Control Registers (PTFPE, PTFSE, PTFDS) ...................................................94 6.5.13 Port G I/O Registers (PTGD and PTGDD) .......................................................................96 6.5.14 Port G Pin Control Registers (PTGPE, PTGSE, PTGDS) ................................................96 Chapter 7 Central Processor Unit (S08CPUV2) 7.1 Introduction .....................................................................................................................................99 7.1.1 Features .............................................................................................................................99 7.2 Programmer’s Model and CPU Registers .....................................................................................100 7.2.1 Accumulator (A) .............................................................................................................100 7.2.2 Index Register (H:X) ......................................................................................................100 7.2.3 Stack Pointer (SP) ...........................................................................................................101 7.2.4 Program Counter (PC) ....................................................................................................101 7.2.5 Condition Code Register (CCR) .....................................................................................101 7.3 Addressing Modes .........................................................................................................................103 7.3.1 Inherent Addressing Mode (INH) ...................................................................................103 7.3.2 Relative Addressing Mode (REL) ..................................................................................103 7.3.3 Immediate Addressing Mode (IMM) ..............................................................................103 7.3.4 Direct Addressing Mode (DIR) ......................................................................................103 7.3.5 Extended Addressing Mode (EXT) ................................................................................104 7.3.6 Indexed Addressing Mode ..............................................................................................104 7.4 Special Operations .........................................................................................................................105 7.4.1 Reset Sequence ...............................................................................................................105 7.4.2 Interrupt Sequence ..........................................................................................................105 7.4.3 Wait Mode Operation ......................................................................................................106 7.4.4 Stop Mode Operation ......................................................................................................106 7.4.5 BGND Instruction ...........................................................................................................107 7.5 HCS08 Instruction Set Summary ..................................................................................................108 MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 11

Chapter 8 5 V Analog Comparator (S08ACMPV2) 8.1 Introduction ...................................................................................................................................119 8.1.1 ACMP Configuration Information ..................................................................................119 8.1.2 ACMP/TPM Configuration Information ........................................................................119 8.1.3 Features ...........................................................................................................................121 8.1.4 Modes of Operation ........................................................................................................121 8.1.5 Block Diagram ................................................................................................................121 8.2 External Signal Description ..........................................................................................................122 8.3 Memory Map ................................................................................................................................122 8.3.1 Register Descriptions ......................................................................................................122 8.4 Functional Description ..................................................................................................................124 Chapter 9 Keyboard Interrupt (S08KBIV2) 9.1 Introduction ...................................................................................................................................125 9.1.1 Features ...........................................................................................................................127 9.1.2 Modes of Operation ........................................................................................................127 9.1.3 Block Diagram ................................................................................................................127 9.2 External Signal Description ..........................................................................................................128 9.3 Register Definition ........................................................................................................................128 9.3.1 KBI Status and Control Register (KBISC) .....................................................................128 9.3.2 KBI Pin Enable Register (KBIPE) ..................................................................................129 9.3.3 KBI Edge Select Register (KBIES) ................................................................................129 9.4 Functional Description ..................................................................................................................130 9.4.1 Edge Only Sensitivity .....................................................................................................130 9.4.2 Edge and Level Sensitivity .............................................................................................130 9.4.3 KBI Pullup/Pulldown Resistors ......................................................................................131 9.4.4 KBI Initialization ............................................................................................................131 Chapter 10 Analog-to-Digital Converter (S08ADC12V1) 10.1 Overview .......................................................................................................................................133 10.1.1 Module Configurations ...................................................................................................133 10.1.2 Low-Power Mode Operation ..........................................................................................135 10.1.3 Features ...........................................................................................................................137 10.1.4 ADC Module Block Diagram .........................................................................................137 10.2 External Signal Description ..........................................................................................................138 10.2.1 Analog Power (V ) ..................................................................................................139 DDAD 10.2.2 Analog Ground (V ) .................................................................................................139 SSAD 10.2.3 Voltage Reference High (V ) ...................................................................................139 REFH 10.2.4 Voltage Reference Low (V ) ....................................................................................139 REFL 10.2.5 Analog Channel Inputs (ADx) ........................................................................................139 10.3 Register Definition ........................................................................................................................139 10.3.1 Status and Control Register 1 (ADCSC1) ......................................................................139 MC9S08JM60 Series Data Sheet, Rev. 5 12 Freescale Semiconductor

10.3.2 Status and Control Register 2 (ADCSC2) ......................................................................141 10.3.3 Data Result High Register (ADCRH) .............................................................................141 10.3.4 Data Result Low Register (ADCRL) ..............................................................................142 10.3.5 Compare Value High Register (ADCCVH) ....................................................................142 10.3.6 Compare Value Low Register (ADCCVL) .....................................................................143 10.3.7 Configuration Register (ADCCFG) ................................................................................143 10.3.8 Pin Control 1 Register (APCTL1) ..................................................................................144 10.3.9 Pin Control 2 Register (APCTL2) ..................................................................................145 10.3.10Pin Control 3 Register (APCTL3) ..................................................................................146 10.4 Functional Description ..................................................................................................................147 10.4.1 Clock Select and Divide Control ....................................................................................148 10.4.2 Input Select and Pin Control ...........................................................................................148 10.4.3 Hardware Trigger ............................................................................................................148 10.4.4 Conversion Control .........................................................................................................148 10.4.5 Automatic Compare Function .........................................................................................151 10.4.6 MCU Wait Mode Operation ............................................................................................151 10.4.7 MCU Stop3 Mode Operation ..........................................................................................152 10.4.8 MCU Stop2 Mode Operation ..........................................................................................152 10.5 Initialization Information ..............................................................................................................152 10.5.1 ADC Module Initialization Example .............................................................................153 10.6 Application Information ................................................................................................................154 10.6.1 External Pins and Routing ..............................................................................................154 10.6.2 Sources of Error ..............................................................................................................156 Chapter 11 Inter-Integrated Circuit (S08IICV2) 11.1 Introduction ...................................................................................................................................159 11.1.1 Features ...........................................................................................................................161 11.1.2 Modes of Operation ........................................................................................................161 11.1.3 Block Diagram ................................................................................................................161 11.2 External Signal Description ..........................................................................................................162 11.2.1 SCL — Serial Clock Line ...............................................................................................162 11.2.2 SDA — Serial Data Line ................................................................................................162 11.3 Register Definition ........................................................................................................................162 11.3.1 IIC Address Register (IICA) ...........................................................................................163 11.3.2 IIC Frequency Divider Register (IICF) ..........................................................................163 11.3.3 IIC Control Register (IICC1) ..........................................................................................166 11.3.4 IIC Status Register (IICS) ...............................................................................................166 11.3.5 IIC Data I/O Register (IICD) ..........................................................................................167 11.3.6 IIC Control Register 2 (IICC2) .......................................................................................168 11.4 Functional Description ..................................................................................................................169 11.4.1 IIC Protocol .....................................................................................................................169 11.4.2 10-bit Address .................................................................................................................172 11.4.3 General Call Address ......................................................................................................173 11.5 Resets ............................................................................................................................................173 MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 13

11.6 Interrupts .......................................................................................................................................173 11.6.1 Byte Transfer Interrupt ....................................................................................................173 11.6.2 Address Detect Interrupt .................................................................................................174 11.6.3 Arbitration Lost Interrupt ................................................................................................174 11.7 Initialization/Application Information ..........................................................................................175 Chapter 12 Multi-Purpose Clock Generator (S08MCGV1) 12.1 Introduction ...................................................................................................................................179 12.1.1 Features ...........................................................................................................................181 12.1.2 Modes of Operation ........................................................................................................183 12.2 External Signal Description ..........................................................................................................183 12.3 Register Definition ........................................................................................................................184 12.3.1 MCG Control Register 1 (MCGC1) ...............................................................................184 12.3.2 MCG Control Register 2 (MCGC2) ...............................................................................185 12.3.3 MCG Trim Register (MCGTRM) ...................................................................................186 12.3.4 MCG Status and Control Register (MCGSC) .................................................................187 12.3.5 MCG Control Register 3 (MCGC3) ...............................................................................188 12.4 Functional Description ..................................................................................................................190 12.4.1 Operational Modes ..........................................................................................................190 12.4.2 Mode Switching ..............................................................................................................194 12.4.3 Bus Frequency Divider ...................................................................................................194 12.4.4 Low Power Bit Usage .....................................................................................................195 12.4.5 Internal Reference Clock ................................................................................................195 12.4.6 External Reference Clock ...............................................................................................195 12.4.7 Fixed Frequency Clock ...................................................................................................195 12.5 Initialization / Application Information ........................................................................................196 12.5.1 MCG Module Initialization Sequence ............................................................................196 12.5.2 MCG Mode Switching ....................................................................................................197 12.5.3 Calibrating the Internal Reference Clock (IRC) .............................................................208 Chapter 13 Real-Time Counter (S08RTCV1) 13.1 Introduction ...................................................................................................................................211 13.1.1 Features ...........................................................................................................................213 13.1.2 Modes of Operation ........................................................................................................213 13.1.3 Block Diagram ................................................................................................................214 13.2 External Signal Description ..........................................................................................................214 13.3 Register Definition ........................................................................................................................214 13.3.1 RTC Status and Control Register (RTCSC) ....................................................................215 13.3.2 RTC Counter Register (RTCCNT) ..................................................................................216 13.3.3 RTC Modulo Register (RTCMOD) ................................................................................216 13.4 Functional Description ..................................................................................................................216 13.4.1 RTC Operation Example .................................................................................................217 13.5 Initialization/Application Information ..........................................................................................218 MC9S08JM60 Series Data Sheet, Rev. 5 14 Freescale Semiconductor

Chapter 14 Serial Communications Interface (S08SCIV4) 14.1 Introduction ...................................................................................................................................221 14.1.1 Features ...........................................................................................................................223 14.1.2 Modes of Operation ........................................................................................................223 14.1.3 Block Diagram ................................................................................................................224 14.2 Register Definition ........................................................................................................................226 14.2.1 SCI Baud Rate Registers (SCIxBDH, SCIxBDL) ..........................................................226 14.2.2 SCI Control Register 1 (SCIxC1) ...................................................................................227 14.2.3 SCI Control Register 2 (SCIxC2) ...................................................................................228 14.2.4 SCI Status Register 1 (SCIxS1) ......................................................................................229 14.2.5 SCI Status Register 2 (SCIxS2) ......................................................................................231 14.2.6 SCI Control Register 3 (SCIxC3) ...................................................................................232 14.2.7 SCI Data Register (SCIxD) .............................................................................................233 14.3 Functional Description ..................................................................................................................233 14.3.1 Baud Rate Generation .....................................................................................................233 14.3.2 Transmitter Functional Description ................................................................................234 14.3.3 Receiver Functional Description ....................................................................................235 14.3.4 Interrupts and Status Flags ..............................................................................................237 14.3.5 Additional SCI Functions ...............................................................................................238 Chapter 15 16-Bit Serial Peripheral Interface (S08SPI16V1) 15.1 Introduction ...................................................................................................................................241 15.1.1 SPI Port Configuration Information ...............................................................................241 15.1.2 Features ...........................................................................................................................244 15.1.3 Modes of Operation ........................................................................................................244 15.1.4 Block Diagrams ..............................................................................................................244 15.2 External Signal Description ..........................................................................................................246 15.2.1 SPSCK — SPI Serial Clock ............................................................................................246 15.2.2 MOSI — Master Data Out, Slave Data In ......................................................................247 15.2.3 MISO — Master Data In, Slave Data Out ......................................................................247 15.2.4 SS — Slave Select ..........................................................................................................247 15.3 Register Definition ........................................................................................................................247 15.3.1 SPI Control Register 1 (SPIxC1) ....................................................................................247 15.3.2 SPI Control Register 2 (SPIxC2) ....................................................................................248 15.3.3 SPI Baud Rate Register (SPIxBR) ..................................................................................250 15.3.4 SPI Status Register (SPIxS) ............................................................................................251 15.3.5 SPI Data Registers (SPIxDH:SPIxDL) ...........................................................................252 15.3.6 SPI Match Registers (SPIxMH:SPIxML) .......................................................................253 15.4 Functional Description ..................................................................................................................254 15.4.1 General ............................................................................................................................254 15.4.2 Master Mode ...................................................................................................................254 15.4.3 Slave Mode .....................................................................................................................255 15.4.4 Data Transmission Length ..............................................................................................256 MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 15

15.4.5 SPI Clock Formats ..........................................................................................................257 15.4.6 SPI Baud Rate Generation ..............................................................................................259 15.4.7 Special Features ..............................................................................................................260 15.4.8 Error Conditions .............................................................................................................261 15.4.9 Low Power Mode Options ..............................................................................................262 15.4.10SPI Interrupts ..................................................................................................................263 15.5 Initialization/Application Information ..........................................................................................265 15.5.1 SPI Module Initialization Example .................................................................................265 Chapter 16 Timer/Pulse-Width Modulator (S08TPMV3) 16.1 Introduction ...................................................................................................................................269 16.1.1 Features ...........................................................................................................................271 16.1.2 Modes of Operation ........................................................................................................271 16.1.3 Block Diagram ................................................................................................................272 16.2 Signal Description .........................................................................................................................274 16.2.1 Detailed Signal Descriptions ..........................................................................................274 16.3 Register Definition ........................................................................................................................278 16.3.1 TPM Status and Control Register (TPMxSC) ................................................................278 16.3.2 TPM-Counter Registers (TPMxCNTH:TPMxCNTL) ....................................................279 16.3.3 TPM Counter Modulo Registers (TPMxMODH:TPMxMODL) ....................................280 16.3.4 TPM Channel n Status and Control Register (TPMxCnSC) ..........................................281 16.3.5 TPM Channel Value Registers (TPMxCnVH:TPMxCnVL) ..........................................283 16.4 Functional Description ..................................................................................................................284 16.4.1 Counter ............................................................................................................................285 16.4.2 Channel Mode Selection .................................................................................................286 16.5 Reset Overview .............................................................................................................................290 16.5.1 General ............................................................................................................................290 16.5.2 Description of Reset Operation .......................................................................................290 16.6 Interrupts .......................................................................................................................................290 16.6.1 General ............................................................................................................................290 16.6.2 Description of Interrupt Operation .................................................................................290 Chapter 17 Universal Serial Bus Device Controller (S08USBV1) 17.1 Introduction ...................................................................................................................................293 17.1.1 Clocking Requirements ...................................................................................................293 17.1.2 Current Consumption in USB Suspend ..........................................................................293 17.1.3 3.3 V Regulator ...............................................................................................................293 17.1.4 Features ...........................................................................................................................296 17.1.5 Modes of Operation ........................................................................................................296 17.1.6 Block Diagram ................................................................................................................297 17.2 External Signal Description ..........................................................................................................298 17.2.1 USBDP ............................................................................................................................298 17.2.2 USBDN ...........................................................................................................................298 MC9S08JM60 Series Data Sheet, Rev. 5 16 Freescale Semiconductor

17.2.3 V USB33 .............................................................................................................................................................298 17.3 Register Definition ........................................................................................................................298 17.3.1 USB Control Register 0 (USBCTL0) .............................................................................299 17.3.2 Peripheral ID Register (PERID) .....................................................................................299 17.3.3 Peripheral ID Complement Register (IDCOMP) ............................................................300 17.3.4 Peripheral Revision Register (REV) ...............................................................................300 17.3.5 Interrupt Status Register (INTSTAT) ..............................................................................301 17.3.6 Interrupt Enable Register (INTENB) ..............................................................................302 17.3.7 Error Interrupt Status Register (ERRSTAT) ...................................................................303 17.3.8 Error Interrupt Enable Register (ERRENB) ...................................................................304 17.3.9 Status Register (STAT) ....................................................................................................305 17.3.10Control Register (CTL) ...................................................................................................306 17.3.11Address Register (ADDR) ..............................................................................................307 17.3.12Frame Number Register (FRMNUML, FRMNUMH) ...................................................307 17.3.13Endpoint Control Register (EPCTLn, n=0-6) .................................................................308 17.4 Functional Description ..................................................................................................................309 17.4.1 Block Descriptions ..........................................................................................................309 17.4.2 Buffer Descriptor Table (BDT) .......................................................................................314 17.4.3 USB Transactions ...........................................................................................................317 17.4.4 USB Packet Processing ...................................................................................................319 17.4.5 Start of Frame Processing ...............................................................................................320 17.4.6 Suspend/Resume .............................................................................................................321 17.4.7 Resets ..............................................................................................................................322 17.4.8 Interrupts .........................................................................................................................323 Chapter 18 Development Support 18.1 Introduction ...................................................................................................................................325 18.1.1 Features ...........................................................................................................................326 18.2 Background Debug Controller (BDC) ..........................................................................................326 18.2.1 BKGD Pin Description ...................................................................................................327 18.2.2 Communication Details ..................................................................................................328 18.2.3 BDC Commands .............................................................................................................332 18.2.4 BDC Hardware Breakpoint .............................................................................................334 18.3 On-Chip Debug System (DBG) ....................................................................................................335 18.3.1 Comparators A and B .....................................................................................................335 18.3.2 Bus Capture Information and FIFO Operation ...............................................................335 18.3.3 Change-of-Flow Information ..........................................................................................336 18.3.4 Tag vs. Force Breakpoints and Triggers .........................................................................336 18.3.5 Trigger Modes .................................................................................................................337 18.3.6 Hardware Breakpoints ....................................................................................................339 18.4 Register Definition ........................................................................................................................339 18.4.1 BDC Registers and Control Bits .....................................................................................339 18.4.2 System Background Debug Force Reset Register (SBDFR) ..........................................341 18.4.3 DBG Registers and Control Bits .....................................................................................342 MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 17

Appendix A Electrical Characteristics A.1 Introduction....................................................................................................................................347 A.2 Parameter Classification.................................................................................................................347 A.3 Absolute Maximum Ratings...........................................................................................................347 A.4 Thermal Characteristics..................................................................................................................348 A.5 ESD Protection and Latch-Up Immunity.......................................................................................349 A.6 DC Characteristics..........................................................................................................................350 A.7 Supply Current Characteristics.......................................................................................................355 A.8 Analog Comparator (ACMP) Electricals.......................................................................................356 A.9 ADC Characteristics.......................................................................................................................356 A.10 External Oscillator (XOSC) Characteristics..................................................................................360 A.11 MCG Specifications.......................................................................................................................361 A.12 AC Characteristics..........................................................................................................................362 A.12.1 Control Timing................................................................................................................362 A.12.2 Timer/PWM (TPM) Module Timing...............................................................................363 A.12.3 SPI Characteristics...........................................................................................................364 A.13 Flash Specifications........................................................................................................................367 A.14 USB Electricals..............................................................................................................................368 A.15 EMC Performance..........................................................................................................................368 A.15.1 Radiated Emissions..........................................................................................................368 Appendix B Ordering Information and Mechanical Drawings B.1 Ordering Information.....................................................................................................................371 B.2 Orderable Part Numbering System................................................................................................371 B.3 Mechanical Drawings.....................................................................................................................371 MC9S08JM60 Series Data Sheet, Rev. 5 18 Freescale Semiconductor

Chapter 1 Device Overview 1.1 Introduction MC9S08JM60 series MCUs are members of the low-cost, high-performance HCS08 Family of 8-bit microcontroller units (MCUs). All MCUs in the family use the enhanced HCS08 core and are available with a variety of modules, memory sizes, memory types, and package types. Table 1-1 summarizes the peripheral availability per package type for the devices available in the MC9S08JM60 series. Table1-1. Devices in the MC9S08JM60 Series Device Feature MC9S08JM60 MC9S08JM32 Package 64-pin 48-pin 44-pin 64-pin 48-pin 44-pin Flash 60,912 32,768 RAM 4096 2048 USB RAM 256 256 ACMP yes yes ADC 12-ch 8-ch 8-ch 12-ch 8-ch 8-ch IIC yes yes IRQ yes yes KBI 8 7 7 8 7 7 SCI1 yes yes SCI2 yes yes SPI1 yes yes SPI2 yes yes TPM1 6-ch 4-ch 4-ch 6-ch 4-ch 4-ch TPM2 2-ch 2-ch USB yes yes I/O pins 51 37 33 51 37 33 64 QFP 64 QFP Package types 48 QFN 44 LQFP 48 QFN 44 LQFP 64 LQFP 64 LQFP 1.2 MCU Block Diagram The block diagram in Figure 1-1 shows the structure of the MC9S08JM60 series MCU. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 19

Chapter1 Device Overview USBDP ON-CHIP ICE AND USBDN HCS08 CORE DEBUG MODULE (DBG) A T 6 R PTA5– PTA0 O USB SIE P BKGD/MS FULL SPEED PTB7/ADP7 BDC CPU USB PTB6/ADP6 USB ENDPOINT TRANSCEIVER PTB5/KBIP5/ADP5 RAM B T PTB4/KBIP4/ADP4 SSPSS2CK2 POR PTB3/SS2/ADP3 RESET HCS08 SYSTEM CONTROL 8-/16-BIT SERIAL PERIPHERAL MOSI2 PTB2/SPSCK2/ADP2 INTERFACE MODULE (SPI2) PTB1/MOSI2/ADP1 MISO2 PTB0/MISO2/ADP0 RESETS AND INTERRUPTS MODES OF OPERATION PTC6 IRQ/TPMCLK POWER MANAGEMENT SERIAL COMMUNICATIONS RxD2 PTC5/RxD2 COP IRQ LVD INTERFACE MODULE (SCI2) TxD2 ORT C PPTTCC34/TxD2 P PTC2 SDA PTC1/SDA IIC MODULE (IIC) SCL PTC0/SCL VDDAD 12-CHANNEL, 12-BIT 8 PTD7 VSSAD ANALOG-TO-DIGITAL 4 PTD6 VREFL CONVERTER (ADC) PTD5 VREFH D PTD4/ADP11 T R PTD3/KBIP3/ADP10 O USER Flash (IN BYTES) P PTD2/KBIP2/ACMPO ACMP– MC9S08JM60 = 60,912 PTD1/ADP9/ACMP– MC9S08JM32 = 32,768 ANALOG COMPARATOR ACMP+ PTD0/ADP8/ACMP+ (ACMP) ACMPO SS1 PTE7/SS1 USER RAM (IN BYTES) SPSCK1 8-/16-BIT SERIAL PERIPHERAL PTE6/SPSCK1 MMCC99SS0088JJMM6302 == 42009468 INTERFACE MODULE (SPI1) MOSI1 PTE5/MOSI1 MISO1 PTE4/MISO1 TPMCLK E MULTI-PURPOSE CLOCK 6-CHMAONDNUELLE T (IMTPEMR1/P)WM TTPPMM11CCHH10 PORT PTE3/TPM1CH1 GENERATOR (MCG) PTE2/TPM1CH0 TPM1CHx4 RxD1 SERIAL COMMUNICATIONS PTE1/RxD1 VSSOSC LOW-POWER OSCILLATOR TxD1 PTE0/TxD1 INTERFACE MODULE (SCI1) PTF7 VDD SYSTEM TPMCLK PTF6 VSS RVEOGLUTLAAGTEO R 2-CHMAONDNUELLE T (IMTPEMR2/P)WM TTPPMM22CCHH10 T F PPTTFF54//TTPPMM22CCHH10 OR PTF3/TPM1CH5 KBIPx P PTF2/TPM1CH4 VUSB33 USB 3.3-V VOLTAGE REGULATOR 8-BIT KEYBOARD 4 PTF1/TPM1CH3 INTERRUPT MODULE (KBI) KBIPx 4 PTF0/TPM1CH2 REAL-TIME COUNTER (RTC) EXTAL PTG5/EXTAL XTAL NOTES: G PTG4/XTAL 1. Port pins are software configurable with pullup device if input port. RT PTG3/KBIP7 O PTG2/KBIP6 2. Pin contains software configurable pullup/pull-down device if IRQ is enabled P PTG1/KBIP1 (IRQPE=1). Pull-down is enabled if rising edge detect is selected (IRQEDG=1) PTG0/KBIP0 3. IRQ does not have a clamp diode to V . IRQ must not be driven above V . DD DD 4. Pin contains integrated pullup device. 5. When pin functions as KBI (KBIPEn = 1) and associated pin is configured to enable the pullup device, KBEDGn can be used to reconfigure the pullup as a pull-down device. Figure1-1. MC9S08JM60 Series Block Diagram MC9S08JM60 Series Data Sheet, Rev. 5 20 Freescale Semiconductor

Chapter1 Device Overview Table 1-2 lists the functional versions of the on-chip modules. Table1-2. Versions of On-Chip Modules Module Version Analog Comparator (ACMP) 2 Analog-to-Digital Converter (ADC) 1 Central Processing Unit (CPU) 2 IIC Module (IIC) 2 Keyboard Interrupt (KBI) 2 Multi-Purpose Clock Generator (MCG) 1 Real-Time Counter (RTC) 1 Serial Communications Interface (SCI) 4 16-bit Serial Peripheral Interface (SPI16) 1 Timer Pulse-Width Modulator (TPM) 3 Universal Serial Bus (USB) 1 Debug Module (DBG) 2 1.3 System Clock Distribution Figure 1-2 shows a simplified clock connection diagram. Some modules in the MCU have selectable clock inputs as shown. The clock inputs to the modules indicate the clock(s) that are used to drive the module function. All memory mapped registers associated with the modules are clocked with BUSCLK. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 21

Chapter1 Device Overview TPMCLK LPO clock 1 kHz RTC COP TPM1 TPM2 IIC SCI1 SCI2 SPI1 SPI2 LPO MCGERCLK MCGIRCLK MCG MCGFFCLK FFCLK1 ÷2 MCGOUT BUSCLK ÷2 MCGLCLK XOSC USB RAM USB CPU BDC ADC2 RAM Flash3 EXTAL XTAL 1. The FFCLK is internally synchronized to the bus clock and must not exceed one half of the bus clock frequency. 2. ADC has min. and max. frequency requirements. See Chapter10, “Analog-to-Digital Converter (S08ADC12V1),” and AppendixA, “Electrical Characteristics,” for details. 3. Flash has the frequency requirements for program and erase operation. See the AppendixA, “Electrical Characteristics,” for details. Figure1-2. System Clock Distribution Diagram The MCG supplies the following clock sources: • MCGOUT — This clock source is used as the CPU, USB RAM and USB module clock, and is divided by two to generate the peripheral bus clock (BUSCLK). Control bits in the MCG control registers determine which of the three clock sources is connected: — Internal reference clock — External reference clock — Frequency-locked loop (FLL) or Phase-locked loop (PLL) output See Chapter12, “Multi-Purpose Clock Generator (S08MCGV1),” for details on configuring the MCGOUT clock. • MCGLCLK — This clock source is derived from the digitally controlled oscillator (DCO) of the MCG. Development tools can select this internal self-clocked source to speed up BDC communications in systems where the bus clock is slow. • MCGIRCLK — This is the internal reference clock and can be selected as the real-time counter clock source. Chapter12, “Multi-Purpose Clock Generator (S08MCGV1),” explains the MCGIRCLK in more detail. See Chapter 13, “Real-Time Counter (S08RTCV1),” for more information regarding the use of MCGIRCLK. • MCGERCLK — This is the external reference clock and can be selected as the clock source of real-time counter and ADC module. Section12.4.6, “External Reference Clock,” explains the MCGERCLK in more detail. See Chapter 13, “Real-Time Counter (S08RTCV1),” and Chapter 10, MC9S08JM60 Series Data Sheet, Rev. 5 22 Freescale Semiconductor

Chapter1 Device Overview “Analog-to-Digital Converter (S08ADC12V1),” for more information regarding the use of MCGERCLK with these modules. • MCGFFCLK — This clock source is divided by 2 to generate FFCLK after being synchronized to the BUSCLK. It can be selected as clock source for the TPM modules. The frequency of the MCGFFCLK is determined by the settings of the MCG. See the Section12.4.7, “Fixed Frequency Clock,” for details. • LPO clock— This clock is generated from an internal Low Power Oscillator that is completely independent of the MCG module. The LPO clock can be selected as the clock source to the RTC or COP modules. See Chapter 13, “Real-Time Counter (S08RTCV1),” and Section5.4, “Computer Operating Properly (COP) Watchdog,” for details on using the LPO clock with these modules. • TPMCLK — TPMCLK is the optional external clock source for the TPM modules. The TPMCLK must be limited to 1/4th the frequency of the BUSCLK for synchronization. See Chapter16, “Timer/Pulse-Width Modulator (S08TPMV3),” for more details. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 23

Chapter1 Device Overview MC9S08JM60 Series Data Sheet, Rev. 5 24 Freescale Semiconductor

Chapter 2 Pins and Connections 2.1 Introduction This chapter describes signals that connect to package pins. It includes pinout diagrams, a table of signal properties, and detailed discussion of signals. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 25

Chapter2 Pins and Connections 2.2 Device Pin Assignment 0 1 P D A PTC5/RxD2 PTC3/TxD2 PTC2 PTC1/SDA PTC0/SCL VSSOSC PTG5/EXTAL PTG4/XTAL BKGD/MS PTG3/KBIP7 PTG2/KBIP6 PTD7 PTD6 PTD5 PTD4/ADP11 PTD3/KBIP3/ 64 49 63 62 61 60 59 58 57 56 55 54 53 52 51 50 PTC4 1 48 PTD2/KBIP2/ACMPO IRQ/TPMCLK 2 47 VSSAD RESET 3 46 VREFL PTF0/TPM1CH2 4 45 VREFH PTF1/TPM1CH3 5 44 V DDAD PTF2/TPM1CH4 6 43 PTD1/ADP9/ACMP– PTF3/TPM1CH5 7 42 PTD0/ADP8/ACMP+ PTF4/TPM2CH0 8 41 PTB7/ADP7 64-Pin QFP/LQFP PTC6 9 40 PTB6/ADP6 PTF7 10 39 PTB5/KBIP5/ADP5 PTF5/TPM2CH1 11 38 PTB4/KBIP4/ADP4 PTF6 12 37 PTB3/SS2/ADP3 PTE0/TxD1 13 36 PTB2/SPSCK2/ADP2 PTE1/RxD1 14 35 PTB1/MOSI2/ADP1 PTE2/TPM1CH0 15 34 PTB0/MISO2/ADP0 PTE3/TPM1CH1 16 33 PTA5 18 19 20 21 22 23 24 25 26 27 28 29 30 31 17 32 PTE4/MISO1 PTE5/MOSI1 TE6/SPSCK1 PTE7/SS1 VDD VSS USBDN USBDP VUSB33 PTG0/KBIP0 PTG1/KBIP1 PTA0 PTA1 PTA2 PTA3 PTA4 P Figure2-1. MC9S08JM60 in 64-Pin QFP/LQFP Package MC9S08JM60 Series Data Sheet, Rev. 5 26 Freescale Semiconductor

Chapter2 Pins and Connections PTC5/RxD2 PTC3/TxD2 PTC2 PTC1/SDA PTC0/SCL VSSOSC PTG5/EXTAL PTG4/XTAL BKGD/MS PTG3/KBIP7 PTG2/KBIP6 PTD7 48 37 47 46 45 44 43 42 41 40 39 38 PTC4 1 36 PTD2/KBIP2/ACMPO IRQ/TPMCLK 2 35 VSSAD/VREFL RESET 3 34 VDDAD/VREFH PTF0/TPM1CH2 4 33 PTD1/ADP9/ACMP– PTF1/TPM1CH3 5 32 PTD0/ADP8/ACMP+ PTF4/TPM2CH0 6 48-Pin QFN 31 PTB5/KBIP5/ADP5 PTF5/TPM2CH1 7 30 PTB4/KBIP4/ADP4 PTF6 8 29 PTB3/SS2/ADP3 PTE0/TxD1 9 28 PTB2/SPSCK2/ADP2 PTE1/RxD1 10 27 PTB1/MOSI2/ADP1 PTE2/TPM1CH0 11 26 PTB0/MISO2/ADP0 PTE3/TPM1CH1 12 25 PTA5 14 15 16 17 18 19 20 21 22 23 13 24 PTE4/MISO1 PTE5/MOSI1 TE6/SPSCK1 PTE7/SS1 VDD VSS USBDN USBDP VUSB33 PTG0/KBIP0 PTG1/KBIP1 PTA0 P Figure2-2. MC9S08JM60 Series in 48-Pin QFN Package MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 27

Chapter2 Pins and Connections PTC5/RxD2 PTC3/TxD2 PTC2 PTC1/SDA PTC0/SCL VSSOSC PTG5/EXTAL PTG4/XTAL BKGD/MS PTG3/KBIP7 PTG2/KBIP6 44 34 43 42 41 40 39 38 37 36 35 PTC4 1 33 PTD2/KBIP2/ACMPO IRQ/TPMCLK 2 32 V /V SSAD REFL RESET 3 31 V /V DDAD REFH PTF0/TPM1CH2 4 30 PTD1/ADP9/ACMP– PTF1/TPM1CH3 5 29 PTD0/ADP8/ACMP+ 44-Pin LQFP PTF4/TPM2CH0 6 28 PTB5/KBIP5/ADP5 PTF5/TPM2CH1 7 27 PTB4/KBIP4/ADP4 PTE0/TxD1 8 26 PTB3/SS2/ADP3 PTE1/RxD1 9 25 PTB2/SPSCK2/ADP2 PTE2/TPM1CH0 10 24 PTB1/MOSI2/ADP1 PTE3/TPM1CH1 11 23 PTB0/MISO2/ADP0 13 14 15 16 17 18 19 20 21 12 22 PTE4/MISO1 PTE5/MOSI1 TE6/SPSCK1 PTE7/SS1 VDD VSS USBDN USBDP VUSB33 PTG0/KBIP0 PTG1/KBIP1 P Figure2-3. MC9S08JM60 Series in 44-Pin LQFP Package 2.3 Recommended System Connections Figure 2-4 shows pin connections that are common to almost all MC9S08JM60 series application systems. MC9S08JM60 Series Data Sheet, Rev. 5 28 Freescale Semiconductor

Chapter2 Pins and Connections VREFH MC9S08JM60 V DDAD CBYAD PORT PTA0–PTA5 0.1 μF A V SPOYSWTEERM VDD VRSESFALD PTB0/MISO2/ADP0 VDD PTB1/MOSI2/ADP1 + PTB2/SPSCK2/ADP2 5 V CBLK + CBY PTB3/SS2/ADP3 10 μF 0.1 μF PORT PTB4/KBIP4/ADP4 V SS B PTB5/KBIP5/ADP5 PTB6/ADP6 PTB7/ADP7 NOTE 1 RF RS PTC0/SCL XTAL PTC1/SDA PTC2 C1 X1 C2 V PTC3/TxD2 SSOSC PORT PTC4 EXTAL C PTC5/RxD2 PTC6 BACKGROUND HEADER I/O AND PTD0/ADP8/ACMP+ PTD1/ADP9/ACMP– VDD BKGD/MS PTD2/KBIP2/ACMPO PERIPHERAL V PTD3/KBIP3/ADP10 INTERFACE TO DD PTD4/ADP11 PORT D PTD5 APPLICATION 4.7 kΩ–10 kΩ PTD6 PTD7 SYSTEM RESET 0.1 μF VDD PTE0/TxD1 PTE1/RxD1 OPTIONAL 4.7 kΩ– PTE2/TPM1CH0 MANUAL ASYNCHRONOUS 10 kΩ PTE3/TPM1CH1 RESET INTERRUPT IRQ PORT PTE4/MISO1 INPUT 0.1 μF E PTE5/MOSI1 PTE6/SPSCK1 PTE7/SS1 3.3-V Reference + VUSB33 PTF0/TPM1CH2 PTF1/TPM1CH3 4.7 μF 0.47 μF PTF2/TPM1CH4 PTF3/TPM1CH5 PORT PTF4/TPM2CH0 F PTF5/TPM2CH1 USB SERIES-B CONNECTOR PTF6 USBDN PTF7 2 1 PTG0/KBIP0 VBus VUSB33 PTG1/KBIP1 3 4 R PORT PTG2/KBIP6 PUDP G PTG3/KBIP7 USBDP PTG4/XTAL PTG5/EXTAL NOTES: 1. External crystal circuity is not required if using the MCG internal clock option. For USB operation, an external crystal is required. 2. XTAL and EXTAL are the same pins as PTG4 and PTG5, respectively. 3. RC filters on RESET and IRQ are recommended for EMC-sensitive applications. 4. R is shown for full-speed USB only. The diagram shows a configuration where the on-chip regulator and R are enabled. PUDP PUDP The voltage regulator output is used for R R can optionally be disabled if using an external pullup resistor on USBDP PUDP. PUDP 5. V is a 5.0-V supply from upstream port that can be used for USB operation BUS 6. USBDP and USBDN are powered by the 3.3-V regulator or external 3.3-V supply on V . USB33 Figure2-4. Basic System Connections MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 29

Chapter2 Pins and Connections 2.3.1 Power (V , V , V , V , V , V ) DD SS SSOSC DDAD SSAD USB33 V and V are the primary power supply pins for the MCU. This voltage source supplies power to all DD SS I/O buffer circuitry and to an internal voltage regulator. The internal voltage regulator provides regulated lower-voltage source to the CPU and other internal circuitry of the MCU. Typically, application systems have two separate capacitors across the power pins. In this case, there must be a bulk electrolytic capacitor, such as a 10-μF tantalum capacitor, to provide bulk charge storage for the overall system and a 0.1-μF ceramic bypass capacitor located as near to the paired V and V power DD SS pins as practical to suppress high-frequency noise. The MC9S08JM60 series have a V pin. This pin SSOSC must be connected to the system ground plane or to the primary V pin through a low-impedance SS connection. V and V are the analog power supply pins for the MCU. This voltage source supplies power to DDAD SSAD the ADC module. A 0.1-μF ceramic bypass capacitor must be located as near to the analog power pins as practical to suppress high-frequency noise. V is connected to the internal USB 3.3-V regulator. V maintains an output voltage of 3.3V and USB33 USB33 can only source enough current for internal USB transceiver and USB pullup resistor. Two separate capacitors (4.7-μF bulk electrolytic stability capacitor and 0.47-μF ceramic bypass capacitors) must be connected across this pin to ground to decrease the output ripple of this voltage regulator when it is enabled. 2.3.2 Oscillator (XTAL, EXTAL) Immediately after reset, the MCU uses an internally generated clock provided by the multi-purpose clock generator (MCG) module. For more information on the MCG, see Chapter 12, “Multi-Purpose Clock Generator (S08MCGV1).” The oscillator (XOSC) in this MCU is a Pierce oscillator that can accommodate a crystal or ceramic resonator. Rather than a crystal or ceramic resonator, an external oscillator can be connected to the EXTAL input pin. R (when used) and R must be low-inductance resistors such as carbon composition resistors. S F Wire-wound resistors, and some metal film resistors, have too much inductance. C1 and C2 normally must be high-quality ceramic capacitors that are specifically designed for high-frequency applications. R is used to provide a bias path to keep the EXTAL input in its linear range during crystal startup; its value F is not generally critical. Typical systems use 1MΩ to 10MΩ. Higher values are sensitive to humidity and lower values reduce gain and (in extreme cases) could prevent startup. C1 and C2 are typically in the 5-pF to 25-pF range and are chosen to match the requirements of a specific crystal or resonator. Be sure to take into account printed circuit board (PCB) capacitance and MCU pin capacitance when selecting C1 and C2. The crystal manufacturer typically specifies a load capacitance which is the series combination of C1 and C2 (which are usually the same size). As a first-order approximation, use 10pF as an estimate of combined pin and PCB capacitance for each oscillator pin (EXTAL and XTAL). MC9S08JM60 Series Data Sheet, Rev. 5 30 Freescale Semiconductor

Chapter2 Pins and Connections 2.3.3 RESET Pin RESET is a dedicated pin with a pullup device built in. It has input hysteresis, a high current output driver, and no output slew rate control. Internal power-on reset and low-voltage reset circuitry typically make external reset circuitry unnecessary. This pin is normally connected to the standard 6-pin background debug connector, so a development system can directly reset the MCU system. If desired, a manual external reset can be added by supplying a simple switch to ground (pull reset pin low to force a reset). Whenever any reset is initiated (whether from an external source or from an internal source, the RESET pin is driven low for approximately 66 bus cycles and released. The reset circuity decodes the cause of reset and records it by setting a corresponding bit in the system control reset status register (SRS). In EMC-sensitive applications, an external RC filter is recommended on the reset pin. See Figure2-4 for an example. 2.3.4 Background/Mode Select (BKGD/MS) When in reset, the BKGD/MS pin functions as a mode select pin. Immediately after reset rises the pin functions as the background pin and can be used for background debug communication. While functioning as a background/mode select pin, the pin includes an internal pullup device, input hysteresis, a standard output driver, and no output slew rate control. If nothing is connected to this pin, the MCU will enter normal operating mode at the rising edge of reset. If a debug system is connected to the 6-pin standard background debug header, it can hold BKGD/MS low during the rising edge of reset which forces the MCU to active background mode. The BKGD pin is used primarily for background debug controller (BDC) communications using a custom protocol that uses 16 clock cycles of the target MCU’s BDC clock per bit time. The target MCU’s BDC clock could be as fast as the bus clock rate, so there must never be any significant capacitance connected to the BKGD/MS pin that could interfere with background serial communications. Although the BKGD pin is a pseudo open-drain pin, the background debug communication protocol provides brief, actively driven, high speedup pulses to ensure fast rise times. Small capacitances from cables and the absolute value of the internal pullup device play almost no role in determining rise and fall times on the BKGD pin. 2.3.5 ADC Reference Pins (V , V ) REFH REFL The V and V pins are the voltage reference high and voltage reference low inputs respectively REFH REFL for the ADC module. 2.3.6 External Interrupt Pin (IRQ) The IRQ pin is the input source for the IRQ interrupt and is also the input for the BIH and BIL instructions. If the IRQ function is not enabled, this pin can be used for TPMCLK. In EMC-sensitive applications, an external RC filter is recommended on the IRQ pin. See Figure2-4 for an example. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 31

Chapter2 Pins and Connections 2.3.7 USB Data Pins (USBDP, USBDN) The USBDP (D+) and USBDN (D–) pins are the analog input/output lines to/from full-speed internal USB transciever. An optional internal pullup resistor for the USBDP pin, R , is available. PUDP 2.3.8 General-Purpose I/O and Peripheral Ports The MC9S08JM60 series of MCUs support up to 51 general-purpose I/O pins, which are shared with on-chip peripheral functions (timers, serial I/O, ADC, keyboard interrupts, etc.). When a port pin is configured as a general-purpose output or a peripheral uses the port pin as an output, software can select one of two drive strengths and enable or disable slew rate control. When a port pin is configured as a general-purpose input or a peripheral uses the port pin as an input, software can enable a pullup device. For information about controlling these pins as general-purpose I/O pins, see the Chapter 6, “Parallel Input/Output.” For information about how and when on-chip peripheral systems use these pins, see the appropriate module chapter. Immediately after reset, all pins are configured as high-impedance general-purpose inputs with internal pullup devices disabled. MC9S08JM60 Series Data Sheet, Rev. 5 32 Freescale Semiconductor

Chapter2 Pins and Connections Table2-1. Pin Availability by Package Pin-Count Pin Number Lowest <--Priority--> Highest Pin Number Lowest <--Priority--> Highest 64 48 44 Port Pin Alt1 Alt2 64 48 44 Port Pin Alt1 Alt2 1 1 1 PTC4 33 25 PTA5 2 2 2 IRQ TPMCLK 34 26 23 PTB0 MISO2 ADP0 3 3 3 RESET 35 27 24 PTB1 MOSI2 ADP1 4 4 4 PTF0 TPM1CH2 36 28 25 PTB2 SPSCK2 ADP2 5 5 5 PTF1 TPM1CH3 37 29 26 PTB3 SS2 ADP3 6 — — PTF2 TPM1CH4 38 30 27 PTB4 KBIP4 ADP4 7 — — PTF3 TPM1CH5 39 31 28 PTB5 KBIP5 ADP5 8 6 6 PTF4 TPM2CH0 40 — — PTB6 ADP6 9 — — PTC6 41 — — PTB7 ADP7 10 — — PTF7 42 32 29 PTD0 ADP8 ACMP+ 11 7 7 PTF5 TPM2CH1 43 33 30 PTD1 ADP9 ACMP– 12 8 — PTF6 44 VDDAD 34 31 13 9 8 PTE0 TxD1 45 VREFH 14 10 9 PTE1 RxD1 46 VREFL 35 32 15 11 10 PTE2 TPM1CH0 47 VSSAD 16 12 11 PTE3 TPM1CH1 48 36 33 PTD2 KBIP2 ACMPO 17 13 12 PTE4 MISO1 49 — — PTD3 KBIP3 ADP10 18 14 13 PTE5 MOSI1 50 — — PTD4 ADP11 19 15 14 PTE6 SPSCK1 51 — — PTD5 20 16 15 PTE7 SS1 52 — — PTD6 21 17 16 V 53 37 — PTD7 DD 22 18 17 V 54 38 34 PTG2 KBIP6 SS 23 19 18 USBDN 55 39 35 PTG3 KBIP7 24 20 19 USBDP 56 40 36 BKGD MS 25 21 20 V 57 41 37 PTG4 XTAL USB33 26 22 21 PTG0 KBIP0 58 42 38 PTG5 EXTAL 27 23 22 PTG1 KBIP1 59 43 39 VSSOSC 28 24 PTA0 60 44 40 PTC0 SCL 29 PTA1 61 45 41 PTC1 SDA 30 PTA2 62 46 42 PTC2 31 PTA3 63 47 43 PTC3 TxD2 32 PTA4 64 48 44 PTC5 RxD2 MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 33

Chapter2 Pins and Connections NOTE When an alternative function is first enabled, it is possible to get a spurious edge to the module, user software must clear out any associated flags before interrupts are enabled. Table 2-1 illustrates the priority if multiple modules are enabled. The highest priority module will have control over the pin. Selecting a higher priority pin function with a lower priority function already enabled can cause spurious edges to the lower priority module. It is recommended that all modules that share a pin be disabled before enabling another module. MC9S08JM60 Series Data Sheet, Rev. 5 34 Freescale Semiconductor

Chapter 3 Modes of Operation 3.1 Introduction The operating modes of the MC9S08JM60 series are described in this chapter. Entry into each mode, exit from each mode, and functionality while in each mode are described. 3.2 Features • Active background mode for code development • Wait mode: — CPU halts operation to conserve power — System clocks running — Full voltage regulation is maintained • Stop modes: CPU and bus clocks stopped — Stop2: Partial power down of internal circuits; RAM and USB RAM contents retained — Stop3: All internal circuits powered for fast recovery; RAM, USB RAM, and register contents are retained 3.3 Run Mode Run is the normal operating mode for the MC9S08JM60 series. This mode is selected upon the MCU exiting reset if the BKGD/MS pin is high. In this mode, the CPU executes code from internal memory with execution beginning at the address fetched from memory at 0xFFFE:0xFFFF after reset. 3.4 Active Background Mode The active background mode functions are managed through the background debug controller (BDC) in the HCS08 core. The BDC, together with the on-chip in-circuit emulator (ICE) debug module (DBG), provides the means for analyzing MCU operation during software development. Active background mode is entered in any of five ways: • When the BKGD/MS pin is low at the rising edge of reset • When a BACKGROUND command is received through the BKGD pin • When a BGND instruction is executed • When encountering a BDC breakpoint • When encountering a DBG breakpoint MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 35

Chapter3 Modes of Operation After entering active background mode, the CPU is held in a suspended state waiting for serial background commands rather than executing instructions from the user application program. Background commands are of two types: • Non-intrusive commands, defined as commands that can be issued while the user program is running. Non-intrusive commands can be issued through the BKGD pin while the MCU is in run mode; non-intrusive commands can also be executed when the MCU is in the active background mode. Non-intrusive commands include: — Memory access commands — Memory-access-with-status commands — BDC register access commands — The BACKGROUND command • Active background commands, which can only be executed while the MCU is in active background mode. Active background commands include commands to: — Read or write CPU registers — Trace one user program instruction at a time — Leave active background mode to return to the user application program (GO) The active background mode is used to program a bootloader or user application program into the flash program memory before the MCU is operated in run mode for the first time. When the MC9S08JM60 series is shipped from the Freescale factory, the flash program memory is erased by default unless specifically noted, so there is no program that could be executed in run mode until the flash memory is initially programmed. The active background mode can also be used to erase and reprogram the flash memory after it has been previously programmed. For additional information about the active background mode, refer to Chapter 18, “Development Support.” 3.5 Wait Mode Wait mode is entered by executing a WAIT instruction. Upon execution of the WAIT instruction, the CPU enters a low-power state in which it is not clocked. The I bit in the condition code register (CCR) is cleared when the CPU enters wait mode, enabling interrupts. When an interrupt request occurs, the CPU exits wait mode and resumes processing, beginning with the stacking operations leading to the interrupt service routine. While the MCU is in wait mode, there are some restrictions on which background debug commands can be used. • Only the BACKGROUND command and memory-access-with-status commands are available while the MCU is in wait mode. • The memory-access-with-status commands do not allow memory access, but they report an error indicating that the MCU is in stop or wait mode. • The BACKGROUND command can be used to wake the MCU from wait mode and enter active background mode. MC9S08JM60 Series Data Sheet, Rev. 5 36 Freescale Semiconductor

Chapter3 Modes of Operation 3.6 Stop Modes One of two stop modes is entered upon execution of a STOP instruction when STOPE in SOPT1 is set. In any stop mode, the bus and CPU clocks are halted. The MCG module can be configured to leave the reference clocks running. See Chapter12, “Multi-Purpose Clock Generator (S08MCGV1),” for more information. Table 3-1 shows all of the control bits that affect stop mode selection and the mode selected under various conditions. The selected mode is entered following the execution of a STOP instruction. Table3-1. Stop Mode Selection STOPE ENBDM 1 LVDE LVDSE PPDC Stop Mode 0 x x x Stop modes disabled; illegal opcode reset if STOP instruction executed 1 1 x x Stop3 with BDM enabled 2 1 0 Both bits must be 1 x Stop3 with voltage regulator active 1 0 Either bit a 0 0 Stop3 1 0 Either bit a 0 1 Stop2 1 ENBDM is located in the BDCSCR which is only accessible through BDC commands, see Section18.4.1.1, “BDC Status and Control Register (BDCSCR).” 2 When in stop3 mode with BDM enabled, The S will be near R levels because internal clocks are IDD IDD enabled. 3.6.1 Stop3 Mode Stop3 mode is entered by executing a STOP instruction under the conditions as shown in Table 3-1. The states of all of the internal registers and logic, RAM contents, and I/O pin states are maintained. Stop3 can be exited by asserting RESET, or by an interrupt from one of the following sources: the real-time clock (RTC) interrupt, the USB resume interrupt, LVD, ADC, IRQ, KBI, SCI, or the ACMP. If stop3 is exited by means of the RESET pin, then the MCU is reset and operation will resume after taking the reset vector. Exit by means of one of the internal interrupt sources results in the MCU taking the appropriate interrupt vector. 3.6.1.1 LVD Enabled in Stop Mode The LVD system is capable of generating either an interrupt or a reset when the supply voltage drops below the LVD voltage. If the LVD is enabled in stop (LVDE and LVDSE bits in SPMSC1 both set) at the time the CPU executes a STOP instruction, then the voltage regulator remains active during stop mode. If the user attempts to enter stop2 with the LVD enabled for stop, the MCU will enter stop3 instead. For the ADC to operate, the LVD must be left enabled when entering stop3. For the ACMP to operate when ACGBS in ACMPSC is set, the LVD must be left enabled when entering stop3. For the XOSC to operate with an external reference when RANGE in MCGC2 is set, the LVD must be left enabled when entering stop3. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 37

Chapter3 Modes of Operation 3.6.1.2 Active BDM Enabled in Stop Mode Entry into the active background mode from run mode is enabled if ENBDM in BDCSCR is set. This register is described in Chapter 18, “Development Support.” If ENBDM is set when the CPU executes a STOP instruction, the system clocks to the background debug logic remain active when the MCU enters stop mode. Because of this, background debug communication remains possible. In addition, the voltage regulator does not enter its low-power standby state but maintains full internal regulation. If the user attempts to enter stop2 with ENBDM set, the MCU will enter stop3 instead. Most background commands are not available in stop mode. The memory-access-with-status commands do not allow memory access, but they report an error indicating that the MCU is in stop or wait mode. The BACKGROUND command can be used to wake the MCU from stop and enter active background mode if the ENBDM bit is set. After entering background debug mode, all background commands are available. 3.6.2 Stop2 Mode Stop2 mode is entered by executing a STOP instruction under the conditions as shown in Table 3-1. Most of the internal circuitry of the MCU is powered off in stop2, with the exception of the RAM. Upon entering stop2, all I/O pin control signals are latched so that the pins retain their states during stop2. Exit from stop2 is performed by asserting either wake-up pin: RESET or IRQ/TPMCLK. NOTE IRQ/TPMCLK always functions as an active-low wakeup input when the MCU is in stop2, regardless of how the pin is configured before entering stop2. It must be configured as an input before executing a STOP instruction to avoid an immediate exit from stop2. This pin must be driven or pulled high externally while in stop2 mode. In addition, the RTC interrupt can wake the MCU from stop2, if enabled. Upon wake-up from stop2 mode, the MCU starts up as from a power-on reset (POR): • All module control and status registers are reset • The LVD reset function is enabled and the MCU remains in the reset state if V is below the LVD DD trip point (low trip point selected due to POR) • The CPU takes the reset vector In addition to the above, upon waking up from stop2, the PPDF bit in SPMSC2 is set. This flag is used to direct user code to go to a stop2 recovery routine. PPDF remains set and the I/O pin states remain latched until a 1 is written to PPDACK in SPMSC2. To maintain I/O states for pins that were configured as general-purpose I/O before entering stop2, the user must restore the contents of the I/O port registers, which have been saved in RAM, to the port registers before writing to the PPDACK bit. If the port registers are not restored from RAM before writing to PPDACK, then the pins will switch to their reset states when PPDACK is written. For pins that were configured as peripheral I/O, the user must reconfigure the peripheral module that interfaces to the pin before writing to the PPDACK bit. If the peripheral module is not enabled before MC9S08JM60 Series Data Sheet, Rev. 5 38 Freescale Semiconductor

Chapter3 Modes of Operation writing to PPDACK, the pins will be controlled by their associated port control registers when the I/O latches are opened. 3.6.3 On-Chip Peripheral Modules in Stop Modes When the MCU enters any stop mode, system clocks to the internal peripheral modules are stopped. Even in the exception case (ENBDM = 1), where clocks to the background debug logic continue to operate, clocks to the peripheral systems are halted to reduce power consumption. Refer to Section3.6.2, “Stop2 Mode,” and Section3.6.1, “Stop3 Mode,” for specific information on system behavior in stop modes. Table3-2. Stop Mode Behavior Mode Peripheral Stop2 Stop3 CPU Off Standby RAM Standby Standby Flash Off Standby Parallel Port Registers Off Standby ADC Off Optionally On1 ACMP Off Optionally On2 MCG Off Optionally On3 IIC Off Standby RTC Optionally on4 Optionally on4 SCI Off Standby SPI Off Standby TPM Off Standby System Voltage Regulator Off Standby XOSC Off Optionally On5 I/O Pins States Held States Held USB (SIE and Transceiver) Off Optionally On6 USB 3.3-V Regulator Off Standby USB RAM Standby Standby 1 Requires the asynchronous ADC clock and LVD to be enabled, else in standby. 2 If ACGBS in ACMPSC is set, LVD must be enabled, else in standby. 3 IRCLKEN and IREFSTEN set in MCGC1, else in standby. 4 RTCPS[3:0] in RTCSC does not equal 0 before entering stop, else off. 5 ERCLKEN and EREFSTEN set in MCGC2, else in standby. For high frequency range (RANGE in MCGC2 set) requires the LVD to also be enabled in stop3. 6 USBEN in CTL is set and USBPHYEN in USBCTL0 is set, else off. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 39

Chapter3 Modes of Operation MC9S08JM60 Series Data Sheet, Rev. 5 40 Freescale Semiconductor

Chapter 4 Memory 4.1 MC9S08JM60 Series Memory Map Figure 4-1 shows the memory map for the MC9S08JM60 series. On-chip memory in the MC9S08JM60 series of MCUs consists of RAM, flash program memory for nonvolatile data storage, plus I/O and control/status registers. The registers are divided into three groups: • Direct-page registers (0x0000 through 0x00AF) • High-page registers (0x1800 through 0x185F) • Nonvolatile registers (0xFFB0 through 0xFFBF) MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 41

Chapter4 Memory 0x0000 0x0000 DIRECT PAGE REGISTERS DIRECT PAGE REGISTERS 0x00AF 0x00AF 0x00B0 0x00B0 RAM RAM 2048 BYTES 4096 BYTES 0x08AF 0x08B0 0x10AF UNIMPLEMENTED 0x10B0 FLASH 3936 BYTES 1872 BYTES 0x17FF 0x17FF 0x1800 0x1800 HIGH PAGE REGISTERS HIGH PAGE REGISTERS 0x185F 96 BYTES 0x185F 96 BYTES 0x1860 0x1860 USB RAM — 256 BYTES USB RAM — 256 BYTES 0x195F 0x195F 0x1960 0x1960 UNIMPLEMENTED 0x7FFF 0x8000 FLASH 59,088 BYTES FLASH 32,768 BYTES 0xFFFF 0xFFFF MC9S08JM60 MC9S08JM32 Figure4-1. MC9S08JM60 Series Memory Map 4.1.1 Reset and Interrupt Vector Assignments Figure 4-1 shows address assignments for reset and interrupt vectors. The vector names shown in this table are the labels used in the Freescale-provided equate file for the MC9S08JM60 series. For more details about resets, interrupts, interrupt priority, and local interrupt mask controls, refer to Chapter5, “Resets, Interrupts, and System Configuration.” Table4-1. Reset and Interrupt Vectors Address Vector Vector Name (High/Low) 0xFFC0:0xFFC1 to Unused Vector Space 0xFFC2:FFC3 0xFFC4:FFC5 RTC Vrtc 0xFFC6:FFC7 IIC Viic 0xFFC8:FFC9 ACMP Vacmp MC9S08JM60 Series Data Sheet, Rev. 5 42 Freescale Semiconductor

Chapter4 Memory Table4-1. Reset and Interrupt Vectors (continued) Address Vector Vector Name (High/Low) 0xFFCA:FFCB ADC Conversion Vadc 0xFFCC:FFCD KBI Vkeyboard 0xFFCE:FFCF SCI2 Transmit Vsci2tx 0xFFD0:FFD1 SCI2 Receive Vsci2rx 0xFFD2:FFD3 SCI2 Error Vsci2err 0xFFD4:FFD5 SCI1 Transmit Vsci1tx 0xFFD6:FFD7 SCI1 Receive Vsci1rx 0xFFD8:FFD9 SCI1 Error Vsci1err 0xFFDA:FFDB TPM2 Overflow Vtpm2ovf 0xFFDC:FFDD TPM2 Channel 1 Vtpm2ch1 0xFFDE:FFDF TPM2 Channel 0 Vtpm2ch0 0xFFE0:FFE1 TPM1 Overflow Vtpm1ovf 0xFFE2:FFE3 TPM1 Channel 5 Vtpm1ch5 0xFFE4:FFE5 TPM1 Channel 4 Vtpm1ch4 0xFFE6:FFE7 TPM1 Channel 3 Vtpm1ch3 0xFFE8:FFE9 TPM1 Channel 2 Vtpm1ch2 0xFFEA:FFEB TPM1 Channel 1 Vtpm1ch1 0xFFEC:FFED TPM1 Channel 0 Vtpm1ch0 0xFFEE:FFEF Reserved — 0xFFF0:FFF1 USB Status Vusb 0xFFF2:FFF3 SPI2 Vspi2 0xFFF4:FFF5 SPI1 Vspi1 0xFFF6:FFF7 MCG Loss of Lock Vlol 0xFFF8:FFF9 Low Voltage Detect Vlvd 0xFFFA:FFFB IRQ Virq 0xFFFC:FFFD SWI Vswi 0xFFFE:FFFF Reset Vreset 4.2 Register Addresses and Bit Assignments The registers in the MC9S08JM60 series are divided into these three groups: • Direct-page registers are located in the first 176 locations in the memory map, so they are accessible with efficient direct addressing mode instructions. • High-page registers are used much less often, so they are located above 0x1800 in the memory map. This leaves more room in the direct page for more frequently used registers and variables. • The nonvolatile register area consists of a block of 16locations in flash memory at 0xFFB0–0xFFBF. Nonvolatile register locations include: — Three values which are loaded into working registers at reset MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 43

Chapter4 Memory — An 8-byte backdoor comparison key which optionally allows a user to gain controlled access to secure memory Because the nonvolatile register locations are flash memory, they must be erased and programmed like other flash memory locations. Direct-page registers can be accessed with efficient direct addressing mode instructions. Bit manipulation instructions can be used to access any bit in any direct-page register. Table 4-2 is a summary of all user-accessible direct-page registers and control bits. The direct page registers in Table 4-2 can use the more efficient direct addressing mode which only requires the lower byte of the address. Because of this, the lower byte of the address in column one is shown in bold text. In Table 4-3 and Table4-4, the whole address in column one is shown in bold. In Table 4-2, Table4-3, and Table4-4, the register names in column two are shown in bold to set them apart from the bit names to the right. Cells that are not associated with named bits are shaded. A shaded cell with a 0 indicates this unused bit always reads as a 0. Shaded cells with dashes indicate unused or reserved bit locations that could read as 1s or 0s. MC9S08JM60 Series Data Sheet, Rev. 5 44 Freescale Semiconductor

Chapter4 Memory Table4-2. Direct-Page Register Summary (Sheet 1 of 4) Register Address Bit 7 6 5 4 3 2 1 Bit 0 Name 0x0000 PTAD — — PTAD5 PTAD4 PTAD3 PTAD2 PTAD1 PTAD0 0x0001 PTADD — — PTADD5 PTADD4 PTADD3 PTADD2 PTADD1 PTADD0 0x0002 PTBD PTBD7 PTBD6 PTBD5 PTBD4 PTBD3 PTBD2 PTBD1 PTBD0 0x0003 PTBDD PTBDD7 PTBDD6 PTBDD5 PTBDD4 PTBDD3 PTBDD2 PTBDD1 PTBDD0 0x0004 PTCD — PTCD6 PTCD5 PTCD4 PTCD3 PTCD2 PTCD1 PTCD0 0x0005 PTCDD — PTCDD6 PTCDD5 PTCDD4 PTCDD3 PTCDD2 PTCDD1 PTCDD0 0x0006 PTDD PTDD7 PTDD6 PTDD5 PTDD4 PTDD3 PTDD2 PTDD1 PTDD0 0x0007 PTDDD PTDDD7 PTDDD6 PTDDD5 PTDDD4 PTDDD3 PTDDD2 PTDDD1 PTDDD0 0x0008 PTED PTED7 PTED6 PTED5 PTED4 PTED3 PTED2 PTED1 PTED0 0x0009 PTEDD PTEDD7 PTEDD6 PTEDD5 PTEDD4 PTEDD3 PTEDD2 PTEDD1 PTEDD0 0x000A PTFD PTFD7 PTFD6 PTFD5 PTFD4 PTFD3 PTFD2 PTFD1 PTFD0 0x000B PTFDD PTFDD7 PTFDD6 PTFDD5 PTFDD4 PTFDD3 PTFDD2 PTFDD1 PTFDD0 0x000C PTGD — — PTGD5 PTGD4 PTGD3 PTGD2 PTGD1 PTGD0 0x000D PTGDD — — PTGDD5 PTGDD4 PTGDD3 PTGDD2 PTGDD1 PTGDD0 0x000E ACMPSC ACME ACBGS ACF ACIE ACO ACOPE ACMOD 0x000F Reserved — — — — — — — — 0x0010 ADCSC1 COCO AIEN ADCO ADCH 0x0011 ADCSC2 ADACT ADTRG ACFE ACFGT 0 0 R R 0x0012 ADCRH 0 0 0 0 ADR11 ADR10 ADR9 ADR8 0x0013 ADCRL ADR7 ADR6 ADR5 ADR4 ADR3 ADR2 ADR1 ADR0 0x0014 ADCCVH 0 0 0 0 ADCV11 ADCV10 ADCV9 ADCV8 0x0015 ADCCVL ADCV7 ADCV6 ADCV5 ADCV4 ADCV3 ADCV2 ADCV1 ADCV0 0x0016 ADCCFG ADLPC ADIV ADLSMP MODE ADICLK 0x0017 APCTL1 ADPC7 ADPC6 ADPC5 ADPC4 ADPC3 ADPC2 ADPC1 ADPC0 0x0018 APCTL2 — — — — ADPC11 ADPC10 ADPC9 ADPC8 0x0019– Reserved — — — — — — — — 0x001A 0x001B IRQSC 0 IRQPDD IRQEDG IRQPE IRQF IRQACK IRQIE IRQMOD 0x001C KBISC 0 0 0 0 KBF KBACK KBIE KBMOD 0x001D KBIPE KBIPE7 KBIPE6 KBIPE5 KBIPE4 KBIPE3 KBIPE2 KBIPE1 KBIPE0 0x001E KBIES KBEDG7 KBEDG6 KBEDG5 KBEDG4 KBEDG3 KBEDG2 KBEDG1 KBEDG0 0x001F Reserved — — — — — — — — 0x0020 TPM1SC TOF TOIE CPWMS CLKSB CLKSA PS2 PS1 PS0 0x0021 TPM1CNTH Bit 15 14 13 12 11 10 9 Bit 8 0x0022 TPM1CNTL Bit 7 6 5 4 3 2 1 Bit 0 0x0023 TPM1MODH Bit 15 14 13 12 11 10 9 Bit 8 0x0024 TPM1MODL Bit 7 6 5 4 3 2 1 Bit 0 0x0025 TPM1C0SC CH0F CH0IE MS0B MS0A ELS0B ELS0A 0 0 0x0026 TPM1C0VH Bit 15 14 13 12 11 10 9 Bit 8 0x0027 TPM1C0VL Bit 7 6 5 4 3 2 1 Bit 0 0x0028 TPM1C1SC CH1F CH1IE MS1B MS1A ELS1B ELS1A 0 0 0x0029 TPM1C1VH Bit 15 14 13 12 11 10 9 Bit 8 MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 45

Chapter4 Memory Table4-2. Direct-Page Register Summary (Sheet 2 of 4) Register Address Bit 7 6 5 4 3 2 1 Bit 0 Name 0x002A TPM1C1VL Bit 7 6 5 4 3 2 1 Bit 0 0x002B TPM1C2SC CH2F CH2IE MS2B MS2A ELS2B ELS2A 0 0 0x002C TPM1C2VH Bit 15 14 13 12 11 10 9 Bit 8 0x002D TPM1C2VL Bit 7 6 5 4 3 2 1 Bit 0 0x002E TPM1C3SC CH3F CH3IE MS3B MS3A ELS3B ELS3A 0 0 0x002F TPM1C3VH Bit 15 14 13 12 11 10 9 Bit 8 0x0030 TPM1C3VL Bit 7 6 5 4 3 2 1 Bit 0 0x0031 TPM1C4SC CH4F CH4IE MS4B MS4A ELS4B ELS4A 0 0 0x0032 TPM1C4VH Bit 15 14 13 12 11 10 9 Bit 8 0x0033 TPM1C4VL Bit 7 6 5 4 3 2 1 Bit 0 0x0034 TPM1C5SC CH5F CH5IE MS5B MS5A ELS5B ELS5A 0 0 0x0035 TPM1C5VH Bit 15 14 13 12 11 10 9 Bit 8 0x0036 TPM1C5VL Bit 7 6 5 4 3 2 1 Bit 0 0x0037 Reserved — — — — — — — — 0x0038 SCI1BDH LBKDIE RXEDGIE 0 SBR12 SBR11 SBR10 SBR9 SBR8 0x0039 SCI1BDL SBR7 SBR6 SBR5 SBR4 SBR3 SBR2 SBR1 SBR0 0x003A SCI1C1 LOOPS SCISWAI RSRC M WAKE ILT PE PT 0x003B SCI1C2 TIE TCIE RIE ILIE TE RE RWU SBK 0x003C SCI1S1 TDRE TC RDRF IDLE OR NF FE PF 0x003D SCI1S2 LBKDIF RXEDGIF 0 RXINV RWUID BRK13 LBKDE RAF 0x003E SCI1C3 R8 T8 TXDIR TXINV ORIE NEIE FEIE PEIE 0x003F SCI1D Bit 7 6 5 4 3 2 1 Bit 0 0x0040 SCI2BDH LBKDIE RXEDGIE 0 SBR12 SBR11 SBR10 SBR9 SBR8 0x0041 SCI2BDL SBR7 SBR6 SBR5 SBR4 SBR3 SBR2 SBR1 SBR0 0x0042 SCI2C1 LOOPS SCISWAI RSRC M WAKE ILT PE PT 0x0043 SCI2C2 TIE TCIE RIE ILIE TE RE RWU SBK 0x0044 SCI2S1 TDRE TC RDRF IDLE OR NF FE PF 0x0045 SCI2S2 LBKDIF RXEDGIF 0 RXINV RWUID BRK13 LBKDE RAF 0x0046 SCI2C3 R8 T8 TXDIR TXINV ORIE NEIE FEIE PEIE 0x0047 SCI2D Bit 7 6 5 4 3 2 1 Bit 0 0x0048 MCGC1 CLKS RDIV IREFS IRCLKEN IREFSTEN 0x0049 MCGC2 BDIV RANGE HGO LP EREFS ERCLKEN EREFSTEN 0x004A MCGTRM TRIM 0x004B MCGSC LOLS LOCK PLLST IREFST CLKST OSCINIT FTRIM 0x004C MCGC3 LOLIE PLLS CME 0 VDIV 0x004D MCGT 0 0 0 0 0 0 0 0 0x004E– Reserved — — — — — — — — 0x004F 0x0050 SPI1C1 SPIE SPE SPTIE MSTR CPOL CPHA SSOE LSBFE 0x0051 SPI1C2 SPMIE SPIMODE 0 MODFEN BIDIROE 0 SPISWAI SPC0 0x0052 SPI1BR 0 SPPR2 SPPR1 SPPR0 0 SPR2 SPR1 SPR0 0x0053 SPI1S SPRF SPMF SPTEF MODF 0 0 0 0 MC9S08JM60 Series Data Sheet, Rev. 5 46 Freescale Semiconductor

Chapter4 Memory Table4-2. Direct-Page Register Summary (Sheet 3 of 4) Register Address Bit 7 6 5 4 3 2 1 Bit 0 Name 0x0054 SPI1DH Bit 15 14 13 12 11 10 9 Bit 8 0x0055 SPI1DL Bit 7 6 5 4 3 2 1 Bit 0 0x0056 SPI1MH Bit 15 14 13 12 11 10 9 Bit 8 0x0057 SPI1ML Bit 7 6 5 4 3 2 1 Bit 0 0x0058 IICA AD7 AD6 AD5 AD4 AD3 AD2 AD1 0 0x0059 IICF MULT ICR 0x005A IICC1 IICEN IICIE MST TX TXAK RSTA 0 0 0x005B IICS TCF IAAS BUSY ARBL 0 SRW IICIF RXAK 0x005C IICD DATA 0x005D IICC2 GCAEN ADEXT 0 0 0 AD10 AD9 AD8 0x005E– Reserved — — — — — — — — 0x005F 0x0060 TPM2SC TOF TOIE CPWMS CLKSB CLKSA PS2 PS1 PS0 0x0061 TPM2CNTH Bit 15 14 13 12 11 10 9 Bit 8 0x0062 TPM2CNTL Bit 7 6 5 4 3 2 1 Bit 0 0x0063 TPM2MODH Bit 15 14 13 12 11 10 9 Bit 8 0x0064 TPM2MODL Bit 7 6 5 4 3 2 1 Bit 0 0x0065 TPM2C0SC CH0F CH0IE MS0B MS0A ELS0B ELS0A 0 0 0x0066 TPM2C0VH Bit 15 14 13 12 11 10 9 Bit 8 0x0067 TPM2C0VL Bit 7 6 5 4 3 2 1 Bit 0 0x0068 TPM2C1SC CH1F CH1IE MS1B MS1A ELS1B ELS1A 0 0 0x0069 TPM2C1VH Bit 15 14 13 12 11 10 9 Bit 8 0x006A TPM2C1VL Bit 7 6 5 4 3 2 1 Bit 0 0x006B Reserved — — — — — — — — 0x006C RTCSC RTIF RTCLKS RTIE RTCPS 0x006D RTCCNT RTCCNT 0x006E RTCMOD RTCMOD 0x006F Reserved — — — — — — — — 0x0070 SPI2C1 SPIE SPE SPTIE MSTR CPOL CPHA SSOE LSBFE 0x0071 SPI2C2 SPMIE SPIMODE 0 MODFEN BIDIROE 0 SPISWAI SPC0 0x0072 SPI2BR 0 SPPR2 SPPR1 SPPR0 0 SPR2 SPR1 SPR0 0x0073 SPI2S SPRF SPMF SPTEF MODF 0 0 0 0 0x0074 SPI2DH Bit 15 14 13 12 11 10 9 Bit 8 0x0075 SPI2DL Bit 7 6 5 4 3 2 1 Bit 0 0x0076 SPI2MH Bit 15 14 13 12 11 10 9 Bit 8 0x0077 SPI2ML Bit 7 6 5 4 3 2 1 Bit 0 0x0078– Reserved — — — — — — — — 0x007F 0x0080 USBCTL0 USBRESET USBPU USBRESMEN LPRESF — USBVREN — USBPHYEN 0x0081– Reserved — — — — — — — — 0x0087 0x0088 PERID 0 0 ID5 ID4 ID3 ID2 ID1 ID0 MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 47

Chapter4 Memory Table4-2. Direct-Page Register Summary (Sheet 4 of 4) Register Address Bit 7 6 5 4 3 2 1 Bit 0 Name 0x0089 IDCOMP 1 1 NID5 NID4 NID3 NID2 NID1 NID0 0x008A REV REV7 REV6 REV5 REV4 REV3 REV2 REV1 REV0 0x008B– Reserved — — — — — — — — 0x008F 0x0090 INTSTAT STALLF — RESUMEF SLEEPF TOKDNEF SOFTOKF ERRORF USBRSTF 0x0091 INTENB STALL — RESUME SLEEP TOKDNE SOFTOK ERROR USBRST 0x0092 ERRSTAT BTSERRF — BUFERRF BTOERRF DFN8F CRC16F CRC5F PIDERRF 0x0093 ERRENB BTSERR — BUFERR BTOERR DFN8 CRC16 CRC5 PIDERR 0x0094 STAT ENDP IN ODD 0 0 0x0095 CTL — — TSUSPEND — — CRESUME ODDRST USBEN 0x0096 ADDR — ADDR6 ADDR5 ADDR4 ADDR3 ADDR2 ADDR1 ADDR0 0x0097 FRMNUML FRM7 FRM6 FRM5 FRM4 FRM3 FRM2 FRM1 FRM0 0x0098 FRMNUMH 0 0 0 0 0 FRM10 FRM9 FRM8 0x0099– Reserved — — — — — — — — 0x009C 0x009D EPCTL0 — — 0 EPCTLDIS EPRXEN EPTXEN EPSTALL EPHSHK 0x009E EPCTL1 — — 0 EPCTLDIS EPRXEN EPTXEN EPSTALL EPHSHK 0x009F EPCTL2 — — 0 EPCTLDIS EPRXEN EPTXEN EPSTALL EPHSHK 0x00A0 EPCTL3 — — 0 EPCTLDIS EPRXEN EPTXEN EPSTALL EPHSHK 0x00A1 EPCTL4 — — 0 EPCTLDIS EPRXEN EPTXEN EPSTALL EPHSHK 0x00A2 EPCTL5 — — 0 EPCTLDIS EPRXEN EPTXEN EPSTALL EPHSHK 0x00A3 EPCTL6 — — 0 EPCTLDIS EPRXEN EPTXEN EPSTALL EPHSHK 0x00A4– Reserved — — — — — — — — 0x00AF High-page registers, shown in Table 4-3, are accessed much less often than other I/O and control registers so they have been located outside the direct addressable memory space, starting at 0x1800. Table4-3. High-Page Register Summary (Sheet 1 of 3) Address Register Name Bit 7 6 5 4 3 2 1 Bit 0 0x1800 SRS POR PIN COP ILOP 0 LOC LVD — 0x1801 SBDFR 0 0 0 0 0 0 0 BDFR 0x1802 SOPT1 COPT STOPE — 0 0 — — 0x1803 SOPT2 COPCLKS COPW 0 0 0 SPI1FE SPI2FE ACIC 0x1804– Reserved — — — — — — — — 0x1805 0x1806 SDIDH — — — — ID11 ID10 ID9 ID8 0x1807 SDIDL ID7 ID6 ID5 ID4 ID3 ID2 ID1 ID0 0x1808 Reserved — — — — — — — — 0x1809 SPMSC1 LVWF LVWACK LVWIE LVDRE LVDSE LVDE 01 BGBE 0x180A SPMSC2 — — LVDV LVWV PPDF PPDACK — PPDC 0x180B– Reserved — — — — — — — — 0x180F MC9S08JM60 Series Data Sheet, Rev. 5 48 Freescale Semiconductor

Chapter4 Memory Table4-3. High-Page Register Summary (Sheet 2 of 3) Address Register Name Bit 7 6 5 4 3 2 1 Bit 0 0x1810 DBGCAH Bit 15 14 13 12 11 10 9 Bit 8 0x1811 DBGCAL Bit 7 6 5 4 3 2 1 Bit 0 0x1812 DBGCBH Bit 15 14 13 12 11 10 9 Bit 8 0x1813 DBGCBL Bit 7 6 5 4 3 2 1 Bit 0 0x1814 DBGFH Bit 15 14 13 12 11 10 9 Bit 8 0x1815 DBGFL Bit 7 6 5 4 3 2 1 Bit 0 0x1816 DBGC DBGEN ARM TAG BRKEN RWA RWAEN RWB RWBEN 0x1817 DBGT TRGSEL BEGIN 0 0 TRG3 TRG2 TRG1 TRG0 0x1818 DBGS AF BF ARMF 0 CNT3 CNT2 CNT1 CNT0 0x1819– Reserved — — — — — — — — 0x181F 0x1820 FCDIV DIVLD PRDIV8 DIV5 DIV4 DIV3 DIV2 DIV1 DIV0 0x1821 FOPT KEYEN FNORED 0 0 0 0 SEC01 SEC00 0x1822 Reserved — — — — — — — — 0x1823 FCNFG 0 0 KEYACC 0 0 0 0 0 0x1824 FPROT FPS7 FPS6 FPS5 FPS4 FPS3 FPS2 FPS1 FPDIS 0x1825 FSTAT FCBEF FCCF FPVIOL FACCERR 0 FBLANK 0 0 0x1826 FCMD FCMD7 FCMD6 FCMD5 FCMD4 FCMD3 FCMD2 FCMD1 FCMD0 0x1827– Reserved — — — — — — — — 0x183F 0x1840 PTAPE — — PTAPE5 PTAPE4 PTAPE3 PTAPE2 PTAPE1 PTAPE0 0x1841 PTASE — — PTASE5 PTASE4 PTASE3 PTASE2 PTASE1 PTASE0 0x1842 PTADS — — PTADS5 PTADS4 PTADS3 PTADS2 PTADS1 PTADS0 0x1843 Reserved — — — — — — — — 0x1844 PTBPE PTBPE7 PTBPE6 PTBPE5 PTBPE4 PTBPE3 PTBPE2 PTBPE1 PTBPE0 0x1845 PTBSE PTBSE7 PTBSE6 PTBSE5 PTBSE4 PTBSE3 PTBSE2 PTBSE1 PTBSE0 0x1846 PTBDS PTBDS7 PTBDS6 PTBDS5 PTBDS4 PTBDS3 PTBDS2 PTBDS1 PTBDS0 0x1847 Reserved — — — — — — — — 0x1848 PTCPE — PTCPE6 PTCPE5 PTCPE4 PTCPE3 PTCPE2 PTCPE1 PTCPE0 0x1849 PTCSE — PTCSE6 PTCSE5 PTCSE4 PTCSE3 PTCSE2 PTCSE1 PTCSE0 0x184A PTCDS — PTCDS6 PTCDS5 PTCDS4 PTCDS3 PTCDS2 PTCDS1 PTCDS0 0x184B Reserved — — — — — — — — 0x184C PTDPE PTDPE7 PTDPE6 PTDPE5 PTDPE4 PTDPE3 PTDPE2 PTDPE1 PTDPE0 0x184D PTDSE PTDSE7 PTDSE6 PTDSE5 PTDSE4 PTDSE3 PTDSE2 PTDSE1 PTDSE0 0x184E PTDDS PTDDS7 PTDDS6 PTDDS5 PTDDS4 PTDDS3 PTDDS2 PTDDS1 PTDDS0 0x184F Reserved — — — — — — — — 0x1850 PTEPE PTEPE7 PTEPE6 PTEPE5 PTEPE4 PTEPE3 PTEPE2 PTEPE1 PTEPE0 0x1851 PTESE PTESE7 PTESE6 PTESE5 PTESE4 PTESE3 PTESE2 PTESE1 PTESE0 0x1852 PTEDS PTEDS7 PTEDS6 PTEDS5 PTEDS4 PTEDS3 PTEDS2 PTEDS1 PTEDS0 0x1853 Reserved — — — — — — — — 0x1854 PTFPE PTFPE7 PTFPE6 PTFPE5 PTFPE4 PTFPE3 PTFPE2 PTFPE1 PTFPE0 0x1855 PTFSE PTFSE7 PTFSE6 PTFSE5 PTFSE4 PTFSE3 PTFSE2 PTFSE1 PTFSE0 0x1856 PTFDS PTFDS7 PTFDS6 PTFDS5 PTFDS4 PTFDS3 PTFDS2 PTFDS1 PTFDS0 MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 49

Chapter4 Memory Table4-3. High-Page Register Summary (Sheet 3 of 3) Address Register Name Bit 7 6 5 4 3 2 1 Bit 0 0x1857 Reserved — — — — — — — — 0x1858 PTGPE — — PTGPE5 PTGPE4 PTGPE3 PTGPE2 PTGPE1 PTGPE0 0x1859 PTGSE — — PTGSE5 PTGSE4 PTGSE3 PTGSE2 PTGSE1 PTGSE0 0x185A PTGDS — — PTGDS5 PTGDS4 PTGDS3 PTGDS2 PTGDS1 PTGDS0 0x185B– Reserved — — — — — — — — 0x185F 1 This reserved bit must always be written to 0. Nonvolatile flash registers, shown in Table 4-4, are located in the flash memory. These registers include an 8-byte backdoor key which optionally can be used to gain access to secure memory resources. During reset events, the contents of NVPROT and NVOPT in the nonvolatile register area of the flash memory are transferred into corresponding FPROT and FOPT working registers in the high-page registers to control security and block protection options. Table4-4. Nonvolatile Register Summary Address Register Name Bit 7 6 5 4 3 2 1 Bit 0 0xFFAE Reserved for 0 0 0 0 0 0 0 FTRIM storage of FTRIM 0xFFAF Res. for storage of TRIM MCGTRIM 0xFFB0– NVBACKKEY 8-Byte Comparison Key 0xFFB7 0xFFB8– Reserved — — — — — — — — 0xFFBC 0xFFBD NVPROT FPS7 FPS6 FPS5 FPS4 FPS3 FPS2 FPS1 FPDIS 0xFFBE Reserved — — — — — — — — 0xFFBF NVOPT KEYEN FNORED 0 0 0 0 SEC01 SEC00 Provided the key enable (KEYEN) bit is 1, the 8-byte comparison key can be used to temporarily disengage memory security. This key mechanism can be accessed only through user code running in secure memory. (A security key cannot be entered directly through background debug commands.) This security key can be disabled completely by programming the KEYEN bit to 0. If the security key is disabled, the only way to disengage security is by mass erasing the flash if needed (normally through the background debug interface) and verifying that flash is blank. To avoid returning to secure mode after the next reset, program the security bits (SEC01:SEC00) to the unsecured state (1:0). 4.3 RAM (System RAM) The MC9S08JM60 series includes static RAM. The locations in RAM below 0x0100 can be accessed using the more efficient direct addressing mode, and any single bit in this area can be accessed with the bit manipulation instructions (BCLR, BSET, BRCLR, and BRSET). Locating the most frequently accessed program variables in this area of RAM is preferred. MC9S08JM60 Series Data Sheet, Rev. 5 50 Freescale Semiconductor

Chapter4 Memory The RAM retains data when the MCU is in low-power wait, stop2, or stop3 mode. At power-on, the contents of RAM are uninitialized. RAM data is unaffected by any reset provided that the supply voltage does not drop below the minimum value for RAM retention. For compatibility with older M68HC05 MCUs, the HCS08 resets the stack pointer to 0x00FF. In the MC9S08JM60 series, it is usually best to re-initialize the stack pointer to the top of the RAM so the direct page RAM can be used for frequently accessed RAM variables and bit-addressable program variables. Include the following 2-instruction sequence in your reset initialization routine (where RamLast is equated to the highest address of the RAM in the Freescale-provided equate file). LDHX #RamLast+1 ;point one past RAM TXS ;SP<-(H:X-1) When security is enabled, the RAM is considered a secure memory resource and is not accessible through BDM or through code executing from non-secure memory. See Section4.6, “Security,” for a detailed description of the security feature. 4.4 USB RAM USB RAM is discussed in detail in Chapter17, “Universal Serial Bus Device Controller (S08USBV1).” 4.5 Flash The flash memory is used for program storage. In-circuit programming allows the operating program to be loaded into the flash memory after final assembly of the application product. It is possible to program the entire array through the single-wire background debug interface. Because no special voltages are needed for flash erase and programming operations, in-application programming is also possible through other software-controlled communication paths. For a more detailed discussion of in-circuit and in-application programming, refer to the HCS08 Family Reference Manual, Volume I, Freescale Semiconductor document order number HCS08RMv1. 4.5.1 Features Features of the flash memory include: • Flash size — MC9S08JM60 — 60,912 bytes (119 pages of 512 bytes each) — MC9S08JM32 — 32,768 bytes (64 pages of 512 bytes each) • Single power supply program and erase • Command interface for fast program and erase operation • Up to 100,000 program/erase cycles at typical voltage and temperature • Flexible block protection • Security feature for flash and RAM • Auto power-down for low-frequency read accesses MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 51

Chapter4 Memory 4.5.2 Program and Erase Times Before any program or erase command can be accepted, the flash clock divider register (FCDIV) must be written to set the internal clock for the flash module to a frequency (f ) between 150kHz and 200kHz FCLK (see Section4.7.1, “Flash Clock Divider Register (FCDIV).”) This register can be written only once, so normally this write is done during reset initialization. FCDIV cannot be written if the access error flag, FACCERR in FSTAT, is set. The user must ensure that FACCERR is not set before writing to the FCDIV register. One period of the resulting clock (1/f ) is used by the command processor to time program FCLK and erase pulses. An integer number of these timing pulses are used by the command processor to complete a program or erase command. Table 4-5 shows program and erase times. The bus clock frequency and FCDIV determine the frequency of FCLK (f ). The time for one cycle of FCLK is t = 1/f . The times are shown as a number FCLK FCLK FCLK of cycles of FCLK and as an absolute time for the case where t =5μs. Program and erase times FCLK shown include overhead for the command state machine and enabling and disabling of program and erase voltages. Table4-5. Program and Erase Times Parameter Cycles of FCLK Time if FCLK=200kHz Byte program 9 45μs Byte program (burst) 4 20μs1 Page erase 4000 20ms Mass erase 20,000 100ms 1 Excluding start/end overhead 4.5.3 Program and Erase Command Execution The steps for executing any of the commands are listed below. The FCDIV register must be initialized and any error flags cleared before beginning command execution. The command execution steps are: 1. Write a data value to an address in the flash array. The address and data information from this write is latched into the flash interface. This write is a required first step in any command sequence. For erase and blank check commands, the value of the data is not important. For page erase commands, the address may be any address in the 512-byte page of flash to be erased. For mass erase and blank check commands, the address can be any address in the flash memory. Whole pages of 512bytes are the smallest block of flash that may be erased. In the 60K version, there are two instances where the size of a block that is accessible to the user is less than 512 bytes: the first page following RAM, and the first page following the high page registers. These pages are overlapped by the RAM and high page registers respectively. NOTE Do not program any byte in the flash more than once after a successful erase operation. Reprogramming bits to a byte which is already programmed is not allowed without first erasing the page in which the byte resides or mass erasing the entire flash memory. Programming without first erasing may disturb data stored in the flash. MC9S08JM60 Series Data Sheet, Rev. 5 52 Freescale Semiconductor

Chapter4 Memory 2. Write the command code for the desired command to FCMD. The five valid commands are blank check (0x05), byte program (0x20), burst program (0x25), page erase (0x40), and mass erase (0x41). The command code is latched into the command buffer. 3. Write a 1 to the FCBEF bit in FSTAT to clear FCBEF and launch the command (including its address and data information). A partial command sequence can be aborted manually by writing a 0 to FCBEF any time after the write to the memory array and before writing the 1 that clears FCBEF and launches the complete command. Aborting a command in this way sets the FACCERR access error flag which must be cleared before starting a new command. A strictly monitored procedure must be obeyed or the command will not be accepted. This minimizes the possibility of any unintended changes to the flash memory contents. The command complete flag (FCCF) indicates when a command is complete. The command sequence must be completed by clearing FCBEF to launch the command. Figure 4-2 is a flowchart for executing all of the commands except for burst programming. The FCDIV register must be initialized before using any flash commands. This only must be done once following a reset. WRITE TO FCDIV (Note 1) Note 1: Required only once after reset. FLASH PROGRAM AND ERASE FLOW START 0 FACCERR ? 1 CLEAR ERROR WRITE TO FLASH TO BUFFER ADDRESS AND DATA WRITE COMMAND TO FCMD WRITE 1 TO FCBEF Note 2: Wait at least four bus cycles TO LAUNCH COMMAND before checking FCBEF or FCCF. AND CLEAR FCBEF (Note 2) FPVIOL OR YES ERROR EXIT FACCERR ? NO 0 FCCF ? 1 DONE Figure4-2. Flash Program and Erase Flowchart MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 53

Chapter4 Memory 4.5.4 Burst Program Execution The burst program command is used to program sequential bytes of data in less time than would be required using the standard program command. This is possible because the high voltage to the flash array does not need to be disabled between program operations. Ordinarily, when a program or erase command is issued, an internal charge pump associated with the flash memory must be enabled to supply high voltage to the array. Upon completion of the command, the charge pump is turned off. When a burst program command is issued, the charge pump is enabled and then remains enabled after completion of the burst program operation if these two conditions are met: • The next burst program command has been queued before the current program operation has completed. • The next sequential address selects a byte on the same physical row as the current byte being programmed. A row of flash memory consists of 64 bytes. A byte within a row is selected by addresses A5 through A0. A new row begins when addresses A5 through A0 are all zero. The first byte of a series of sequential bytes being programmed in burst mode will take the same amount of time to program as a byte programmed in standard mode. Subsequent bytes will program in the burst program time provided that the conditions above are met. In the case the next sequential address is the beginning of a new row, the program time for that byte will be the standard time instead of the burst time. This is because the high voltage to the array must be disabled and then enabled again. If a new burst command has not been queued before the current command completes, then the charge pump will be disabled and high voltage removed from the array. MC9S08JM60 Series Data Sheet, Rev. 5 54 Freescale Semiconductor

Chapter4 Memory WRITE TO FCDIV (Note 1) Note 1: Required only once after reset. FLASH BURST START PROGRAM FLOW 0 FACCERR ? 1 CLEAR ERROR 0 FCBEF ? 1 WRITE TO FLASH TO BUFFER ADDRESS AND DATA WRITE COMMAND (0x25) TO FCMD WRITE 1 TO FCBEF Note 2: Wait at least four bus cycles before TO LAUNCH COMMAND checking FCBEF or FCCF. AND CLEAR FCBEF (Note 2) FPVIO OR YES ERROR EXIT FACCERR ? NO YES NEW BURST COMMAND ? NO 0 FCCF ? 1 DONE Figure4-3. Flash Burst Program Flowchart 4.5.5 Access Errors An access error occurs whenever the command execution protocol is violated. Any of the following specific actions will cause the access error flag (FACCERR) in FSTAT to be set. FACCERR must be cleared by writing a 1 to FACCERR in FSTAT before any command can be processed. • Writing to a flash address before the internal flash clock frequency has been set by writing to the FCDIV register • Writing to a flash address while FCBEF is not set (A new command cannot be started until the command buffer is empty.) • Writing a second time to a flash address before launching the previous command (There is only one write to flash for every command.) MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 55

Chapter4 Memory • Writing a second time to FCMD before launching the previous command (There is only one write to FCMD for every command.) • Writing to any flash control register other than FCMD after writing to a flash address • Writing any command code other than the five allowed codes (0x05, 0x20, 0x25, 0x40, or 0x41) to FCMD • Writing any flash control register other than the write to FSTAT (to clear FCBEF and launch the command) after writing the command to FCMD. • The MCU enters stop mode while a program or erase command is in progress (The command is aborted.) • Writing the byte program, burst program, or page erase command code (0x20, 0x25, or 0x40) with a background debug command while the MCU is secured (The background debug controller can only do blank check and mass erase commands when the MCU is secure.) • Writing 0 to FCBEF to cancel a partial command 4.5.6 Flash Block Protection The block protection feature prevents the protected region of flash from program or erase changes. Block protection is controlled through the flash protection register (FPROT). When enabled, block protection begins at any 512 byte boundary below the last address of flash, 0xFFFF. (see Section4.7.4, “Flash Protection Register (FPROT and NVPROT).”) After exit from reset, FPROT is loaded with the contents of the NVPROT location which is in the nonvolatile register block of the flash memory. FPROT cannot be changed directly from application software so a runaway program cannot alter the block protection settings. Since NVPROT is within the last 512 bytes of flash, if any amount of memory is protected, NVPROT is itself protected and cannot be altered (intentionally or unintentionally) by the application software. FPROT can be written through background debug commands which allows a way to erase and reprogram a protected flash memory. The block protection mechanism is illustrated below. The FPS bits are used as the upper bits of the last address of unprotected memory. This address is formed by concatenating FPS7:FPS1 with logic 1 bits as shown. For example, in order to protect the last 8192 bytes of memory (addresses 0xE000 through 0xFFFF), the FPS bits must be set to 1101 111 which results in the value 0xDFFF as the last address of unprotected memory. In addition to programming the FPS bits to the appropriate value, FPDIS (bit 0 of NVPROT) must be programmed to logic 0 to enable block protection. Therefore the value 0xDE must be programmed into NVPROT to protect addresses 0xE000 through 0xFFFF. FPS7 FPS6 FPS5 FPS4 FPS3 FPS2 FPS1 1 1 1 1 1 1 1 1 1 A15 A14 A13 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 Figure4-4. Block Protection Mechanism One use for block protection is to block protect an area of flash memory for a bootloader program. This bootloader program then can be used to erase the rest of the flash memory and reprogram it. Because the MC9S08JM60 Series Data Sheet, Rev. 5 56 Freescale Semiconductor

Chapter4 Memory bootloader is protected, it remains intact even if MCU power is lost in the middle of an erase and reprogram operation. 4.5.7 Vector Redirection Whenever any block protection is enabled, the reset and interrupt vectors will be protected. Vector redirection allows users to modify interrupt vector information without unprotecting bootloader and reset vector space. Vector redirection is enabled by programming the FNORED bit in the NVOPT register located at address 0xFFBF to zero. For redirection to occur, at least some portion but not all of the flash memory must be block protected by programming the NVPROT register located at address 0xFFBD. All of the interrupt vectors (memory locations 0xFFC0–0xFFFD) are redirected, though the reset vector (0xFFFE:FFFF) is not. For example, if 512 bytes of flash are protected, the protected address region is from 0xFE00 through 0xFFFF. The interrupt vectors (0xFFC0–0xFFFD) are redirected to the locations 0xFDC0–0xFDFD. Now, if a TPM1 overflow interrupt is taken for instance, the values in the locations 0xFDE0:FDE1 are used for the vector instead of the values in the locations 0xFFE0:FFE1. This allows the user to reprogram the unprotected portion of the flash with new program code including new interrupt vector values while leaving the protected area, which includes the default vector locations, unchanged. 4.6 Security The MC9S08JM60 Series includes circuitry to prevent unauthorized access to the contents of flash and RAM memory. When security is engaged, flash and RAM are considered secure resources. Direct-page registers, high-page registers, and the background debug controller are considered unsecured resources. Programs executing within secure memory have normal access to any MCU memory locations and resources. Attempts to access a secure memory location with a program executing from an unsecured memory space or through the background debug interface are blocked (writes are ignored and reads return all 0s). Security is engaged or disengaged based on the state of two nonvolatile register bits (SEC01:SEC00) in the FOPT register. During reset, the contents of the nonvolatile location NVOPT are copied from flash into the working FOPT register in high-page register space. A user engages security by programming the NVOPT location which can be done at the same time the flash memory is programmed. The 1:0 state disengages security and the other three combinations engage security. Notice the erased state (1:1) makes the MCU secure. During development, whenever the flash is erased, it is good practice to immediately program the SEC00 bit to 0 in NVOPT so SEC01:SEC00= 1:0. This would allow the MCU to remain unsecured after a subsequent reset. The on-chip debug module cannot be enabled while the MCU is secure. The separate background debug controller can still be used for background memory access commands, but the MCU cannot enter active background mode except by holding BKGD/MS low at the rising edge of reset. A user can choose to allow or disallow a security unlocking mechanism through an 8-byte backdoor security key. If the nonvolatile KEYEN bit in NVOPT/FOPT is 0, the backdoor key is disabled and there MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 57

Chapter4 Memory is no way to disengage security without completely erasing all flash locations. If KEYEN is 1, a secure user program can temporarily disengage security by: 1. Writing 1 to KEYACC in the FCNFG register. This makes the flash module interpret writes to the backdoor comparison key locations (NVBACKKEY through NVBACKKEY+7) as values to be compared against the key rather than as the first step in a flash program or erase command. 2. Writing the user-entered key values to the NVBACKKEY through NVBACKKEY+7 locations. These writes must be done in order starting with the value for NVBACKKEY and ending with NVBACKKEY+7. STHX must not be used for these writes because these writes cannot be done on adjacent bus cycles. User software normally would get the key codes from outside the MCU system through a communication interface such as a serial I/O. 3. Writing 0 to KEYACC in the FCNFG register. If the 8-byte key that was just written matches the key stored in the flash locations, SEC01:SEC00 are automatically changed to 1:0 and security will be disengaged until the next reset. The security key can be written only from secure memory (either RAM or flash), so it cannot be entered through background commands without the cooperation of a secure user program. The backdoor comparison key (NVBACKKEY through NVBACKKEY+7) is located in flash memory locations in the nonvolatile register space so users can program these locations exactly as they would program any other flash memory location. The nonvolatile registers are in the same 512-byte block of flash as the reset and interrupt vectors, so block protecting that space also block protects the backdoor comparison key. Block protects cannot be changed from user application programs, so if the vector space is block protected, the backdoor security key mechanism cannot permanently change the block protect, security settings, or the backdoor key. Security can always be disengaged through the background debug interface by taking these steps: 1. Disable any block protections by writing FPROT. FPROT can be written only with background debug commands, not from application software. 2. Mass erase flash if necessary. 3. Blank check flash. Provided flash is completely erased, security is disengaged until the next reset. To avoid returning to secure mode after the next reset, program NVOPT so SEC01:SEC00=1:0. 4.7 Flash Registers and Control Bits The flash module has nine 8-bit registers in the high-page register space, three locations in the nonvolatile register space in flash memory which are copied into three corresponding high-page control registers at reset. There is also an 8-byte comparison key in flash memory. Refer to Table 4-3 and Table4-4 for the absolute address assignments for all flash registers. This section refers to registers and control bits only by their names. A Freescale-provided equate or header file normally is used to translate these names into the appropriate absolute addresses. MC9S08JM60 Series Data Sheet, Rev. 5 58 Freescale Semiconductor

Chapter4 Memory 4.7.1 Flash Clock Divider Register (FCDIV) Bit 7 of this register is a read-only status flag. Bits 6 through 0 may be read at any time but can be written only one time. Before any erase or programming operations are possible, write to this register to set the frequency of the clock for the nonvolatile memory system within acceptable limits. 7 6 5 4 3 2 1 0 R DIVLD PRDIV8 DIV5 DIV4 DIV3 DIV2 DIV1 DIV0 W Reset 0 0 0 0 0 0 0 0 = Unimplemented or Reserved Figure4-5. Flash Clock Divider Register (FCDIV) Table4-6. FCDIV Register Field Descriptions Field Description 7 Divisor Loaded Status Flag — When set, this read-only status flag indicates that the FCDIV register has been DIVLD written since reset. Reset clears this bit and the first write to this register causes this bit to become set regardless of the data written. 0 FCDIV has not been written since reset; erase and program operations disabled for flash. 1 FCDIV has been written since reset; erase and program operations enabled for flash. 6 Prescale (Divide) Flash Clock by 8 PRDIV8 0 Clock input to the flash clock divider is the bus rate clock. 1 Clock input to the flash clock divider is the bus rate clock divided by8. 5:0 Divisor for Flash Clock Divider — The flash clock divider divides the bus rate clock (or the bus rate clock DIV[5:0] divided by 8 if PRDIV8=1) by the value in the 6-bit DIV5:DIV0 field plus one. The resulting frequency of the internal flash clock must fall within the range of 200kHz to 150kHz for proper flash operations. Program/Erase timing pulses are one cycle of this internal flash clock which corresponds to a range of 5μs to 6.7μs. The automated programming logic uses an integer number of these pulses to complete an erase or program operation. See Equation4-1, Equation4-2, and Table4-6. if PRDIV8=0 — f = f ÷ ([DIV5:DIV0] + 1) Eqn.4-1 FCLK Bus if PRDIV8=1 — f = f ÷ (8 × ([DIV5:DIV0] + 1)) Eqn.4-2 FCLK Bus Table 4-7 shows the appropriate values for PRDIV8 and DIV5:DIV0 for selected bus frequencies. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 59

Chapter4 Memory Table4-7. Flash Clock Divider Settings PRDIV8 DIV5:DIV0 Program/Erase Timing Pulse f f Bus (Binary) (Decimal) FCLK (5μs Min, 6.7 μs Max) 24 MHz 1 14 200 kHz 5 μs 20 MHz 1 12 192.3 kHz 5.2μs 10 MHz 0 49 200 kHz 5μs 8 MHz 0 39 200 kHz 5μs 4 MHz 0 19 200 kHz 5μs 2 MHz 0 9 200 kHz 5μs 1 MHz 0 4 200 kHz 5μs 200 kHz 0 0 200 kHz 5μs 150 kHz 0 0 150 kHz 6.7μs 4.7.2 Flash Options Register (FOPT and NVOPT) During reset, the contents of the nonvolatile location NVOPT are copied from flash into FOPT. Bits 5 through 2 are not used and always read 0. This register may be read at any time, but writes have no meaning or effect. To change the value in this register, erase and reprogram the NVOPT location in flash memory as usual and then issue a new MCU reset. 7 6 5 4 3 2 1 0 R KEYEN FNORED 0 0 0 0 SEC01 SEC00 W Reset This register is loaded from nonvolatile location NVOPT during reset. = Unimplemented or Reserved Figure4-6. Flash Options Register (FOPT) Table4-8. FOPT Register Field Descriptions Field Description 7 Backdoor Key Mechanism Enable — When this bit is 0, the backdoor key mechanism cannot be used to KEYEN disengage security. The backdoor key mechanism is accessible only from user (secured) firmware. BDM commands cannot be used to write key comparison values that would unlock the backdoor key. For more detailed information about the backdoor key mechanism, refer to Section4.6, “Security.” 0 No backdoor key access allowed. 1 If user firmware writes an 8-byte value that matches the nonvolatile backdoor key (NVBACKKEY through NVBACKKEY+7 in that order), security is temporarily disengaged until the next MCU reset. 6 Vector Redirection Disable — When this bit is 1, then vector redirection is disabled. FNORED 0 Vector redirection enabled. 1 Vector redirection disabled. 1:0 Security State Code — This 2-bit field determines the security state of the MCU as shown in Table4-9. When SEC0[1:0] the MCU is secure, the contents of RAM and flash memory cannot be accessed by instructions from any unsecured source including the background debug interface. For more detailed information about security, refer to Section4.6, “Security.” MC9S08JM60 Series Data Sheet, Rev. 5 60 Freescale Semiconductor

Chapter4 Memory Table4-9. Security States SEC01:SEC00 Description 0:0 secure 0:1 secure 1:0 unsecured 1:1 secure SEC01:SEC00 changes to 1:0 after successful backdoor key entry or a successful blank check of flash. 4.7.3 Flash Configuration Register (FCNFG) Bits 7 through 5 may be read or written at any time. Bits 4 through 0 always read 0 and cannot be written. 7 6 5 4 3 2 1 0 R 0 0 0 0 0 0 0 KEYACC W Reset 0 0 0 0 0 0 0 0 = Unimplemented or Reserved Figure4-7. Flash Configuration Register (FCNFG) Table4-10. FCNFG Register Field Descriptions Field Description 5 Enable Writing of Access Key — This bit enables writing of the backdoor comparison key. For more detailed KEYACC information about the backdoor key mechanism, refer to Section4.6, “Security.” 0 Writes to 0xFFB0–0xFFB7 are interpreted as the start of a flash programming or erase command. 1 Writes to NVBACKKEY (0xFFB0–0xFFB7) are interpreted as comparison key writes. 4.7.4 Flash Protection Register (FPROT and NVPROT) During reset, the contents of the nonvolatile location NVPROT is copied from flash into FPROT. This register may be read at any time, but user program writes have no meaning or effect. Background debug commands can write to FPROT. 7 6 5 4 3 2 1 0 R FPS7 FPS6 FPS5 FPS4 FPS3 FPS2 FPS1 FPDIS W (1) (1) (1) (1) (1) (1) (1) (1) Reset This register is loaded from nonvolatile location NVPROT during reset. 1 Background commands can be used to change the contents of these bits in FPROT. Figure4-8. Flash Protection Register (FPROT) MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 61

Chapter4 Memory Table4-11. FPROT Register Field Descriptions Field Description 7:1 Flash Protect Select Bits — When FPDIS=0, this 7-bit field determines the ending address of unprotected FPS[7:1] flash locations at the high address end of the flash. Protected flash locations cannot be erased or programmed. 0 Flash Protection Disable FPDIS 0 Flash block specified by FPS[7:1] is block protected (program and erase not allowed). 1 No flash block is protected. 4.7.5 Flash Status Register (FSTAT) Bits 3, 1, and 0 always read 0 and writes have no meaning or effect. The remaining five bits are status bits that can be read at any time. Writes to these bits have special meanings that are discussed in the bit descriptions. 7 6 5 4 3 2 1 0 R FCCF 0 FBLANK 0 0 FCBEF FPVIOL FACCERR W Reset 1 1 0 0 0 0 0 0 = Unimplemented or Reserved Figure4-9. Flash Status Register (FSTAT) Table4-12. FSTAT Register Field Descriptions Field Description 7 Flash Command Buffer Empty Flag — The FCBEF bit is used to launch commands. It also indicates that the FCBEF command buffer is empty so that a new command sequence can be executed when performing burst programming. The FCBEF bit is cleared by writing a one to it or when a burst program command is transferred to the array for programming. Only burst program commands can be buffered. 0 Command buffer is full (not ready for additional commands). 1 A new burst program command may be written to the command buffer. 6 Flash Command Complete Flag — FCCF is set automatically when the command buffer is empty and no FCCF command is being processed. FCCF is cleared automatically when a new command is started (by writing 1 to FCBEF to register a command). Writing to FCCF has no meaning or effect. 0 Command in progress 1 All commands complete 5 Protection Violation Flag — FPVIOL is set automatically when FCBEF is cleared to register a command that FPVIOL attempts to erase or program a location in a protected block (the erroneous command is ignored). FPVIOL is cleared by writing a 1 to FPVIOL. 0 No protection violation. 1 An attempt was made to erase or program a protected location. MC9S08JM60 Series Data Sheet, Rev. 5 62 Freescale Semiconductor

Chapter4 Memory Table4-12. FSTAT Register Field Descriptions (continued) Field Description 4 Access Error Flag — FACCERR is set automatically when the proper command sequence is not obeyed exactly FACCERR (the erroneous command is ignored), if a program or erase operation is attempted before the FCDIV register has been initialized, or if the MCU enters stop while a command was in progress. For a more detailed discussion of the exact actions that are considered access errors, see Section4.5.5, “Access Errors.” FACCERR is cleared by writing a 1 to FACCERR. Writing a 0 to FACCERR has no meaning or effect. 0 No access error. 1 An access error has occurred. 2 Flash Verified as All Blank (erased) Flag — FBLANK is set automatically at the conclusion of a blank check FBLANK command if the entire flash array was verified to be erased. FBLANK is cleared by clearing FCBEF to write a new valid command. Writing to FBLANK has no meaning or effect. 0 After a blank check command is completed and FCCF=1, FBLANK=0 indicates the flash array is not completely erased. 1 After a blank check command is completed and FCCF=1, FBLANK=1 indicates the flash array is completely erased (all 0xFF). 4.7.6 Flash Command Register (FCMD) Only five command codes are recognized in normal user modes as shown in Table 4-14. Refer to Section4.5.3, “Program and Erase Command Execution,” for a detailed discussion of flash programming and erase operations. 7 6 5 4 3 2 1 0 R 0 0 0 0 0 0 0 0 W FCMD7 FCMD6 FCMD5 FCMD4 FCMD3 FCMD2 FCMD1 FCMD0 Reset 0 0 0 0 0 0 0 0 Figure4-10. Flash Command Register (FCMD) Table4-13. FCMD Register Field Descriptions Field Description FCMD[7:0] Flash Command Bits — See Table4-14 Table4-14. Flash Commands Command FCMD Equate File Label Blank check 0x05 mBlank Byte program 0x20 mByteProg Byte program — burst mode 0x25 mBurstProg Page erase (512 bytes/page) 0x40 mPageErase Mass erase (all flash) 0x41 mMassErase All other command codes are illegal and generate an access error. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 63

Chapter4 Memory It is not necessary to perform a blank check command after a mass erase operation. Only blank check is required as part of the security unlocking mechanism. MC9S08JM60 Series Data Sheet, Rev. 5 64 Freescale Semiconductor

Chapter 5 Resets, Interrupts, and System Configuration 5.1 Introduction This chapter discusses basic reset and interrupt mechanisms and the various sources of reset and interrupts in the MC9S08JM60 series. Some interrupt sources from peripheral modules are discussed in greater detail within other chapters of this data manual. This chapter gathers basic information about all reset and interrupt sources in one place for easy reference. A few reset and interrupt sources, including the computer operating properly (COP) watchdog, are not part of on-chip peripheral systems with their own sections but are part of the system control logic. 5.2 Features Reset and interrupt features include: • Multiple sources of reset for flexible system configuration and reliable operation • Reset status register (SRS) to indicate source of most recent reset • Separate interrupt vectors for each module (reduces polling overhead) (see Table5-1) 5.3 MCU Reset Resetting the MCU provides a way to start processing from a known set of initial conditions. During reset, most control and status registers are forced to initial values and the program counter is loaded from the reset vector (0xFFFE:0xFFFF). On-chip peripheral modules are disabled and I/O pins are initially configured as general-purpose high-impedance inputs with pullup devices disabled. The I bit in the condition code register (CCR) is set to block maskable interrupts so the user program has a chance to initialize the stack pointer (SP) and system control settings. SP is forced to 0x00FF at reset. The MC9S08JM60 series has seven sources for reset: • Power-on reset (POR) • Low-voltage detect (LVD) • Computer operating properly (COP) timer • Illegal opcode detect (ILOP) • Background debug forced reset • External reset pin (RESET) • Clock generator loss of lock and loss of clock reset (LOC) MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 65

Chapter5 Resets, Interrupts, and System Configuration Each of these sources, with the exception of the background debug forced reset, has an associated bit in the system reset status (SRS) register. 5.4 Computer Operating Properly (COP) Watchdog The COP watchdog is intended to force a system reset when the application software fails to execute as expected. To prevent a system reset from the COP timer (when it is enabled), application software must reset the COP counter periodically. If the application program gets lost and fails to reset the COP counter before it times out, a system reset is generated to force the system back to a known starting point. After any reset, the COP watchdog is enabled (see Section5.7.4, “System Options Register 1 (SOPT1),” for additional information). If the COP watchdog is not used in an application, it can be disabled by clearing COPT bits in SOPT1. The COP counter is reset by writing 0x55 and 0xAA (in this order) to the address of SRS during the selected timeout period. Writes do not affect the data in the read-only SRS. As soon as the write sequence is done, the COP timeout period is restarted. If the program fails to do this during the time-out period, the MCU will reset. Also, if any value other than 0x55 or 0xAA is written to SRS, the MCU is immediately reset. The COPCLKS bit in SOPT2 (see Section5.7.5, “System Options Register 2 (SOPT2),” for additional information) selects the clock source used for the COP timer. The clock source options are either the bus clock or an internal 1 kHz LPO clock source. With each clock source, there are three associated time-outs controlled by the COPT bits in SOPT1. Table 5-6 summaries the control functions of the COPCLKS and COPT bits. The COP watchdog defaults to operation from the 1 kHz LPO clock source and the longest time-out (210 cycles). When the bus clock source is selected, windowed COP operation is available by setting COPW in the SOPT2 register. In this mode, writes to the SRS register to clear the COP timer must occur in the last 25% of the selected timeout period. A premature write immediately resets the MCU. When the 1 kHz LPO clock source is selected, windowed COP operation is not available. The COP counter is initialized by the first writes to the SOPT1 and SOPT2 registers and after any system reset. Subsequent writes to SOPT1 and SOPT2 have no effect on COP operation. Even if the application will use the reset default settings of COPT, COPCLKS, and COPW bits, the user must write to the write-once SOPT1 and SOPT2 registers during reset initialization to lock in the settings. This will prevent accidental changes if the application program gets lost. The write to SRS that services (clears) the COP counter must not be placed in an interrupt service routine (ISR) because the ISR could continue to be executed periodically even if the main application program fails. If the bus clock source is selected, the COP counter does not increment while the MCU is in background debug mode or while the system is in stop mode. The COP counter resumes when the MCU exits background debug mode or stop mode. If the 1 kHz LPO clock source is selected, the COP counter is re-initialized to zero upon entry to either background debug mode or stop mode and begins from zero upon exit from background debug mode or stop mode. MC9S08JM60 Series Data Sheet, Rev. 5 66 Freescale Semiconductor

Chapter5 Resets, Interrupts, and System Configuration 5.5 Interrupts Interrupts provide a way to save the current CPU status and registers, execute an interrupt service routine (ISR), and then restore the CPU status so processing resumes where it left off before the interrupt. Other than the software interrupt (SWI), which is a program instruction, interrupts are caused by hardware events such as an edge on the IRQ pin or a timer-overflow event. The debug module can also generate an SWI under certain circumstances. If an event occurs in an enabled interrupt source, an associated read-only status flag will become set. The CPU will not respond until and unless the local interrupt enable is a logic 1 to enable the interrupt. The Ibit in the CCR is 0 to allow interrupts. The global interrupt mask (I bit) in the CCR is initially set after reset which masks (prevents) all maskable interrupt sources. The user program initializes the stack pointer and performs other system setup before clearing the I bit to allow the CPU to respond to interrupts. When the CPU receives a qualified interrupt request, it completes the current instruction before responding to the interrupt. The interrupt sequence obeys the same cycle-by-cycle sequence as the SWI instruction and consists of: • Saving the CPU registers on the stack • Setting the I bit in the CCR to mask further interrupts • Fetching the interrupt vector for the highest-priority interrupt that is currently pending • Filling the instruction queue with the first three bytes of program information starting from the address fetched from the interrupt vector locations While the CPU is responding to the interrupt, the I bit is automatically set to avoid the possibility of another interrupt interrupting the ISR itself (this is called nesting of interrupts). Normally, the I bit is restored to 0 when the CCR is restored from the value stacked on entry to the ISR. In rare cases, the I bit may be cleared inside an ISR (after clearing the status flag that generated the interrupt) so that other interrupts can be serviced without waiting for the first service routine to finish. This practice is not recommended for anyone other than the most experienced programmers because it can lead to subtle program errors that are difficult to debug. The interrupt service routine ends with a return-from-interrupt (RTI) instruction which restores the CCR, A, X, and PC registers to their pre-interrupt values by reading the previously saved information off the stack. NOTE For compatibility with the M68HC08, the H register is not automatically saved and restored. It is good programming practice to push H onto the stack at the start of the interrupt service routine (ISR) and restore it immediately before the RTI that is used to return from the ISR. When two or more interrupts are pending when the I bit is cleared, the highest priority source is serviced first (see Table 5-1). MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 67

Chapter5 Resets, Interrupts, and System Configuration 5.5.1 Interrupt Stack Frame Figure 5-1 shows the contents and organization of a stack frame. Before the interrupt, the stack pointer (SP) points at the next available byte location on the stack. The current values of CPU registers are stored on the stack starting with the low-order byte of the program counter (PCL) and ending with the CCR. After stacking, the SP points at the next available location on the stack which is the address that is one less than the address where the CCR was saved. The PC value that is stacked is the address of the instruction in the main program that would have executed next if the interrupt had not occurred. TOWARD LOWER ADDRESSES UNSTACKING ORDER 7 0 SP AFTER INTERRUPT STACKING 5 1 CONDITION CODE REGISTER 4 2 ACCUMULATOR 3 3 INDEX REGISTER (LOW BYTE X)* 2 4 PROGRAM COUNTER HIGH SP BEFORE 1 5 PROGRAM COUNTER LOW THE INTERRUPT STACKING TOWARD HIGHER ADDRESSES ORDER * High byte (H) of index register is not automatically stacked. Figure5-1. Interrupt Stack Frame When an RTI instruction is executed, these values are recovered from the stack in reverse order. As part of the RTI sequence, the CPU fills the instruction pipeline by reading three bytes of program information, starting from the PC address recovered from the stack. The status flag causing the interrupt must be acknowledged (cleared) before returning from the ISR. Typically, the flag must be cleared at the beginning of the ISR so that if another interrupt is generated by this same source, it will be registered so it can be serviced after completion of the current ISR. 5.5.2 External Interrupt Request (IRQ) Pin External interrupts are managed by the IRQSC status and control register. When the IRQ function is enabled, synchronous logic monitors the pin for edge-only or edge-and-level events. When the MCU is in stop mode and system clocks are shut down, a separate asynchronous path is used so the IRQ (if enabled) can wake the MCU. 5.5.2.1 Pin Configuration Options The IRQ pin enable (IRQPE) control bit in IRQSC must be 1 in order for the IRQ pin to act as the interrupt request (IRQ) input. As an IRQ input, the user can choose the polarity of edges or levels detected (IRQEDG), whether the pin detects edges-only or edges and levels (IRQMOD), and whether an event causes an interrupt or only sets the IRQF flag which can be polled by software. MC9S08JM60 Series Data Sheet, Rev. 5 68 Freescale Semiconductor

Chapter5 Resets, Interrupts, and System Configuration The IRQ pin, when enabled, defaults to use an internal pull device (IRQPDD = 0), the device is a pullup or pull-down depending on the polarity chosen. If the user desires to use an external pullup or pull-down, the IRQPDD can be written to a 1 to turn off the internal device. BIH and BIL instructions may be used to detect the level on the IRQ pin when the pin is configured to act as the IRQ input. NOTE This pin does not contain a clamp diode to V and must not be driven DD above V . The voltage measured on the internally pulled up IRQ pin may DD be as low as V – 0.7 V. The internal gates connected to this pin are pulled DD all the way to V . DD 5.5.2.2 Edge and Level Sensitivity The IRQMOD control bit re-configure the detection logic so it detects edge events and pin levels. In this edge detection mode, the IRQF status flag becomes set when an edge is detected (when the IRQ pin changes from the deasserted to the asserted level), but the flag is continuously set (and cannot be cleared) as long as the IRQ pin remains at the asserted level. 5.5.3 Interrupt Vectors, Sources, and Local Masks Table 5-1 provides a summary of all interrupt sources. Higher-priority sources are located toward the bottom of the table. The high-order byte of the address for the interrupt service routine is located at the first address in the vector address column, and the low-order byte of the address for the interrupt service routine is located at the next higher address. When an interrupt condition occurs, an associated flag bit becomes set. If the associated local interrupt enable is 1, an interrupt request is sent to the CPU. Within the CPU, if the global interrupt mask (I bit in the CCR) is 0, the CPU will finish the current instruction, stack the PCL, PCH, X, A, and CCR CPU registers, set the I bit, and then fetch the interrupt vector for the highest priority pending interrupt. Processing then continues in the interrupt service routine. Table5-1. Vector Summary (from Lowest to Highest Priority) Vector Address Vector Name Module Source Enable Description Number (High/Low) 31 to 30 0xFFC0:FFC1 Unused vector space (available for user program) 0xFFC2:FFC3 29 0xFFC4:FFC5 Vrtc System RTIF RTIE RTC real-time interrupt control 28 0xFFC6:FFC7 Viic IIC IICIF IICIE IIC 27 0xFFC8:FFC9 Vacmp ACMP ACF ACIE ACMP 26 0xFFCA:FFCB Vadc ADC COCO AIEN ADC 25 0xFFCC:FFCD Vkeyboard KBI KBF KBIE Keyboard pins 24 0xFFCE:FFCF Vsci2tx SCI2 TDRE TIE SCI2 transmit TC TCIE MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 69

Chapter5 Resets, Interrupts, and System Configuration Table5-1. Vector Summary (from Lowest to Highest Priority) (continued) Vector Address Vector Name Module Source Enable Description Number (High/Low) 23 0xFFD0:FFD1 Vsci2rx SCI2 IDLE ILIE SCI2 receive RDRF RIE 22 0xFFD2:FFD3 Vsci2err SCI2 OR ORIE SCI2 error NF NFIE FE FEIE PF PFIE 21 0xFFD4:FFD5 Vsci1tx SCI1 TDRE TIE SCI1 transmit TC TCIE 20 0xFFD6:FFD7 Vsci1rx SCI1 IDLE ILIE SCI1 receive RDRF RIE 19 0xFFD8:FFD9 Vsci1err SCI1 OR ORIE SCI1 error NF NFIE FE FEIE PF PFIE 18 0xFFDA:FFDB Vtpm2ovf TPM2 TOF TOIE TPM2 overflow 17 0xFFDC:FFDD Vtpm2ch1 TPM2 CH1F CH1IE TPM2 channel 1 16 0xFFDE:FFDF Vtpm2ch0 TPM2 CH0F CH0IE TPM2 channel 0 15 0xFFE0:FFE1 Vtpm1ovf TPM1 TOF TOIE TPM1 overflow 14 0xFFE2:FFE3 Vtpm1ch5 TPM1 CH5F CH5IE TPM1 channel 5 13 0xFFE4:FFE5 Vtpm1ch4 TPM1 CH4F CH4IE TPM1 channel 4 12 0xFFE6:FFE7 Vtpm1ch3 TPM1 CH3F CH3IE TPM1 channel 3 11 0xFFE8:FFE9 Vtpm1ch2 TPM1 CH2F CH2IE TPM1 channel 2 10 0xFFEA:FFEB Vtpm1ch1 TPM1 CH1F CH1IE TPM1 channel 1 9 0xFFEC:FFED Vtpm1ch0 TPM1 CH0F CH0IE TPM1 channel 0 8 0xFFEE:FFEF Reserved — — — — 7 0xFFF0:FFF1 Vusb USB STALLF STALL USB Status RESUMEF RESUME SLEEPF SLEEP TOKDNEF TOKDNE SOFTOKF SOFTOK ERRORF ERROR USBRSTF USBRST 6 0xFFF2:FFF3 Vspi2 SPI2 SPRF SPIE SPI2 MODF SPIE SPTEF SPTIE SPMF SPMIE 5 0xFFF4:FFF5 Vspi1 SPI1 SPRF SPIE SPI1 MODF SPIE SPTEF SPTIE SPMF SPMIE 4 0xFFF6:FFF7 Vlol MCG LOLS LOLIE MCG loss of lock 3 0xFFF8:FFF9 Vlvd System LVWF LVWIE Low-voltage detect control 2 0xFFFA:FFFB Virq IRQ IRQF IRQIE IRQ pin MC9S08JM60 Series Data Sheet, Rev. 5 70 Freescale Semiconductor

Chapter5 Resets, Interrupts, and System Configuration Table5-1. Vector Summary (from Lowest to Highest Priority) (continued) Vector Address Vector Name Module Source Enable Description Number (High/Low) 1 0xFFFC:FFFD Vswi Core SWI Instruction — Software interrupt 0 0xFFFE:FFFF Vreset System COP COPE Watchdog timer control LVD LVDRE Low-voltage detect RESET pin — External pin Illegal opcode ILOP Illegal opcode LOC CME Loss of clock POR POR Power-on-reset BDFR BDFR BDM-forced reset 5.6 Low-Voltage Detect (LVD) System The MC9S08JM60 series includes a system to protect against low-voltage conditions in order to protect memory contents and control MCU system states during supply voltage variations. The system is comprised of a power-on reset (POR) circuit and a LVD circuit with trip voltages for warning and detection. The LVD circuit is enabled when LVDE in SPMSC1 is set to 1. The LVD is disabled upon entering any of the stop modes unless LVDSE is set in SPMSC1. If LVDSE and LVDE are both set, then the MCU cannot enter stop2 (it will enter stop3 instead), and the current consumption in stop3 with the LVD enabled will be higher. 5.6.1 Power-On Reset Operation When power is initially applied to the MCU, or when the supply voltage drops below the power-on reset rearm voltage level, V , the POR circuit will cause a reset condition. As the supply voltage rises, the POR LVD circuit will hold the MCU in reset until the supply has risen above the low voltage detection low threshold, V . Both the POR bit and the LVD bit in SRS are set following a POR. LVDL 5.6.2 Low-Voltage Detection (LVD) Reset Operation The LVD can be configured to generate a reset upon detection of a low voltage condition by setting LVDRE to 1. The low voltage detection threshold is determined by the LVDV bit. After an LVD reset has occurred, the LVD system will hold the MCU in reset until the supply voltage has risen above the low voltage detection threshold. The LVD bit in the SRS register is set following either an LVD reset or POR. 5.6.3 Low-Voltage Warning (LVW) Interrupt Operation The LVD system has a low voltage warning flag to indicate to the user that the supply voltage is approaching the low voltage condition. When a low voltage warning condition is detected and is configured for interrupt operation (LVWIE set to 1), LVWF in SPMSC1 will be set and an LVW interrupt request will occur. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 71

Chapter5 Resets, Interrupts, and System Configuration 5.7 Reset, Interrupt, and System Control Registers and Control Bits One 8-bit register in the direct page register space and eight 8-bit registers in the high-page register space are related to reset and interrupt systems. Refer to the direct-page register summary in Chapter4, “Memory,” of this data sheet for the absolute address assignments for all registers. This section refers to registers and control bits only by their names. A Freescale-provided equate or header file is used to translate these names into the appropriate absolute addresses. Some control bits in the SOPT1 and SPMSC2 registers are related to modes of operation. Although brief descriptions of these bits are provided here, the related functions are discussed in greater detail in Chapter 3, “Modes of Operation.” 5.7.1 Interrupt Pin Request Status and Control Register (IRQSC) This direct page register includes status and control bits, which are used to configure the IRQ function, report status, and acknowledge IRQ events. 7 6 5 4 3 2 1 0 R 0 IRQF 0 IRQPDD IRQEDG IRQPE IRQIE IRQMOD W IRQACK Reset 0 0 0 0 0 0 0 0 = Unimplemented or Reserved Figure5-2. Interrupt Request Status and Control Register (IRQSC) Table5-2. IRQSC Register Field Descriptions Field Description 6 Interrupt Request (IRQ) Pull Device Disable — This read/write control bit is used to disable the internal pullup IRQPDD device when the IRQ pin is enabled (IRQPE = 1) allowing for an external device to be used. 0 IRQ pull device enabled if IRQPE = 1. 1 IRQ pull device disabled if IRQPE = 1. 5 Interrupt Request (IRQ) Edge Select — This read/write control bit is used to select the polarity of edges or IRQEDG levels on the IRQ pin that cause IRQF to be set. The IRQMOD control bit determines whether the IRQ pin is sensitive to both edges and levels or only edges. When the IRQ pin is enabled as the IRQ input and is configured to detect rising edges, the optional pullup resistor is re-configured as an optional pulldown resistor. 0 IRQ is falling edge or falling edge/low-level sensitive. 1 IRQ is rising edge or rising edge/high-level sensitive. 4 IRQ Pin Enable — This read/write control bit enables the IRQ pin function. When this bit is set the IRQ pin can IRQPE be used as an interrupt request. 0 IRQ pin function is disabled. 1 IRQ pin function is enabled. 3 IRQ Flag — This read-only status bit indicates when an interrupt request event has occurred. IRQF 0 No IRQ request. 1 IRQ event detected. MC9S08JM60 Series Data Sheet, Rev. 5 72 Freescale Semiconductor

Chapter5 Resets, Interrupts, and System Configuration Table5-2. IRQSC Register Field Descriptions (continued) Field Description 2 IRQ Acknowledge — This write-only bit is used to acknowledge interrupt request events (write 1 to clear IRQF). IRQACK Writing 0 has no meaning or effect. Reads always return 0. If edge-and-level detection is selected (IRQMOD=1), IRQF cannot be cleared while the IRQ pin remains at its asserted level. 1 IRQ Interrupt Enable — This read/write control bit determines whether IRQ events generate an interrupt IRQIE request. 0 Interrupt request when IRQF set is disabled (use polling). 1 Interrupt requested whenever IRQF=1. 0 IRQ Detection Mode — This read/write control bit selects either edge-only detection or edge-and-level IRQMOD detection. See Section5.5.2.2, “Edge and Level Sensitivity,” for more details. 0 IRQ event on falling/rising edges only. 1 IRQ event on falling/rising edges and low/high levels. 5.7.2 System Reset Status Register (SRS) This register includes seven read-only status flags to indicate the source of the most recent reset. When a debug host forces reset by writing 1 to BDFR in the SBDFR register, none of the status bits in SRS will be set. Writing any value except 0x55 and 0xAA in sequence to this register address causes the MCU reset with the source of COP. The reset state of these bits depends on what caused the MCU to reset. 7 6 5 4 3 2 1 0 R POR PIN COP ILOP 0 LOC LVD — W Writing any value to SRS address clears COP watchdog timer. POR 1 0 0 0 0 0 1 0 LVR: U 0 0 0 0 0 1 0 Any other 0 (1) (1) (1) 0 (1) 0 0 reset: U = Unaffected by reset 1 Any of these reset sources that are active at the time of reset will cause the corresponding bit(s) to be set; bits corresponding to sources that are not active at the time of reset will be cleared. Figure5-3. System Reset Status (SRS) Table5-3. SRS Register Field Descriptions Field Description 7 Power-On Reset — Reset was caused by the power-on detection logic. Because the internal supply voltage was POR ramping up at the time, the low-voltage reset (LVR) status bit is also set to indicate that the reset occurred while the internal supply was below the LVR threshold. 0 Reset not caused by POR. 1 POR caused reset. 6 External Reset Pin — Reset was caused by an active-low level on the external reset pin. PIN 0 Reset not caused by external reset pin. 1 Reset came from external reset pin. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 73

Chapter5 Resets, Interrupts, and System Configuration Table5-3. SRS Register Field Descriptions (continued) Field Description 5 Computer Operating Properly (COP) Watchdog — Reset was caused by the COP watchdog timer timing out. COP This reset source may be blocked by COPE=0. 0 Reset not caused by COP timeout. 1 Reset caused by COP timeout. 4 Illegal Opcode — Reset was caused by an attempt to execute an unimplemented or illegal opcode. The STOP ILOP instruction is considered illegal if stop is disabled by STOPE=0 in the SOPT register. The BGND instruction is considered illegal if active background mode is disabled by ENBDM=0 in the BDCSC register. 0 Reset not caused by an illegal opcode. 1 Reset caused by an illegal opcode. 2 Loss-of-Clock Reset — Reset was caused by a loss of external clock. LOC 0 Reset not caused by a loss of external clock. 1 Reset caused by a loss of external clock. 1 Low Voltage Detect — If the LVD is enable with the LVDRE or LVDSE bit is set, and the supply drops below the LVD LVD trip voltage, an LVD reset will occur. This bit is also set by POR. 0 Reset not caused by LVD trip or POR. 1 Reset caused by LVD trip or POR. 5.7.3 System Background Debug Force Reset Register (SBDFR) This register contains a single write-only control bit. A serial background command such as WRITE_BYTE must be used to write to SBDFR. Attempts to write this register from a user program are ignored. Reads always return 0x00. 7 6 5 4 3 2 1 0 R 0 0 0 0 0 0 0 0 W BDFR1 Reset 0 0 0 0 0 0 0 0 = Unimplemented or Reserved 1 BDFR is writable only through serial background debug commands, not from user programs. Figure5-4. System Background Debug Force Reset Register (SBDFR) Table5-4. SBDFR Register Field Descriptions Field Description 0 Background Debug Force Reset — A serial background command such as WRITE_BYTE may be used to BDFR allow an external debug host to force a target system reset. Writing logic 1 to this bit forces an MCU reset. This bit cannot be written from a user program. 5.7.4 System Options Register 1 (SOPT1) This register may be read at any time. Bits 3 and 2 are unimplemented and always read 0. This is a write-once register so only the first write after reset is honored. Any subsequent attempt to write to SOPT (intentionally or unintentionally) is ignored to avoid accidental changes to these sensitive settings. SOPT MC9S08JM60 Series Data Sheet, Rev. 5 74 Freescale Semiconductor

Chapter5 Resets, Interrupts, and System Configuration must be written during the user’s reset initialization program to set the desired controls even if the desired settings are the same as the reset settings. 7 6 5 4 3 2 1 0 R 0 0 COPT STOPE W Reset 1 1 0 1 0 0 1 1 = Unimplemented or Reserved Figure5-5. System Options Register (SOPT1) Table5-5. SOPT1 Register Field Descriptions Field Description 7:6 COP Watchdog Timeout — These write-once bits select the timeout period of the COP. COPT along with COPT[1:0] COPCLKS in SOPT2 defines the COP timeout period. See Table5-6. 5 Stop Mode Enable — This write-once bit defaults to 0 after reset, which disables stop mode. If stop mode is STOPE disabled and a user program attempts to execute a STOP instruction, an illegal opcode reset is forced. 0 Stop mode disabled. 1 Stop mode enabled. Table5-6. COP Configuration Options Control Bits COP Window1 Opens Clock Source COP Overflow Count (COPW = 1) COPCLKS COPT[1:0] N/A 0:0 N/A N/A COP is disabled 0 0:1 1 kHz LPO N/A 25 cycles (32 ms2) clock 0 1:0 1 kHz LPO N/A 28 cycles (256 ms1) clock 0 1:1 1 kHz LPO N/A 210 cycles (1.024 s1) clock 1 0:1 BUSCLK 6144 cycles 213 cycles 1 1:0 BUSCLK 49,152 cycles 216 cycles 1 1:1 BUSCLK 196,608 cycles 218 cycles 1 Windowed COP operation requires the user to clear the COP timer in the last 25% of the selected timeout period. This column displays the minimum number of clock counts required before the COP timer can be reset when in windowed COP mode (COPW=1). 2 Values shown in milliseconds based on t =1ms. See t in the appendix SectionA.12.1, “Control Timing,” for the LPO LPO tolerance of this value. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 75

Chapter5 Resets, Interrupts, and System Configuration 5.7.5 System Options Register 2 (SOPT2) 7 6 5 4 3 2 1 0 R 0 0 0 COPCLKS1 COPW1 SPI1FE SPI2FE ACIC W Reset 0 0 0 0 0 1 1 0 = Unimplemented or Reserved 1 This bit can be written only one time after reset. Additional writes are ignored. Figure5-6. System Options Register 2 (SOPT2) Table5-7. SOPT2 Register Field Descriptions Field Description 7 COP Watchdog Clock Select — This write-once bit selects the clock source of the COP watchdog. COPCLKS 0 Internal 1 kHz LPO clock is source to COP. 1 Bus clock is source to COP. 6 COP Window — This write-once bit selects the COP operation mode. When set, the 0x55-0xAA write sequence COPW to the SRS register must occur in the last 25% of the selected period. Any write to the SRS register during the first 75% of the selected period will reset the MCU. 0 Normal COP operation. 1 Window COP operation. 2 SPI1 Ports Input Filter Enable SPI1FE 0 Disable input filter on SPI1 port pins to allow for higher maximum SPI baud rate. 1 Enable input filter on SPI1 port pins to eliminate noise and restrict maximum SPI baud rate. 1 SPI2 Ports Input Filter Enable SPI2FE 0 Disable input filter on SPI2 port pins to allow for higher maximum SPI baud rate. 1 Enable input filter on SPI2 port pins to eliminate noise and restrict maximum SPI baud rate. 0 Analog Comparator to Input Capture Enable— This bit connects the output of ACMP to TPM input channel0. ACIC 0 ACMP output not connected to TPM input channel 0. 1 ACMP output connected to TPM input channel 0. 5.7.6 System Device Identification Register (SDIDH, SDIDL) This read-only register is included so host development systems can identify the HCS08 derivative and revision number. This allows the development software to recognize where specific memory blocks, registers, and control bits are located in a target MCU. 7 6 5 4 3 2 1 0 R ID11 ID10 ID9 ID8 W Reset — — — — 0 0 0 0 = Unimplemented or Reserved Figure5-7. System Device Identification Register — High (SDIDH) MC9S08JM60 Series Data Sheet, Rev. 5 76 Freescale Semiconductor

Chapter5 Resets, Interrupts, and System Configuration Table5-8. SDIDH Register Field Descriptions Field Description 7:4 Bits 7:4 are reserved. Reading these bits will result in an indeterminate value; writes have no effect. Reserved 3:0 Part Identification Number — Each derivative in the HCS08 Family has a unique identification number. The ID[11:8] MC9S08JM60 Series is hard coded to the value 0x016. See also ID bits in Table5-9. 7 6 5 4 3 2 1 0 R ID7 ID6 ID5 ID4 ID3 ID2 ID1 ID0 W Reset 0 0 0 1 0 1 1 0 = Unimplemented or Reserved Figure5-8. System Device Identification Register — Low (SDIDL) Table5-9. SDIDL Register Field Descriptions Field Description 7:0 Part Identification Number — Each derivative in the HCS08 Family has a unique identification number. The ID[7:0] MC9S08JM60 Series is hard coded to the value 0x016. See also ID bits in Table5-8. 5.7.7 System Power Management Status and Control 1 Register (SPMSC1) This high page register contains status and control bits to support the low-voltage detect function, and to enable the bandgap voltage reference for use by the ADC module. This register must be written during the user’s reset initialization program to set the desired controls even if the desired settings are the same as the reset settings. 7 6 5 4 3 2 1 0 R LVWF1 0 0 LVWIE LVDRE2 LVDSE LVDE2 BGBE W LVWACK Reset: 0 0 0 1 1 1 0 0 = Unimplemented or Reserved 1 LVWF will be set in the case when V transitions below the trip point or after reset and V is already below V . Supply Supply LVW 2 This bit can be written only one time after reset. Additional writes are ignored. Figure5-9. System Power Management Status and Control 1 Register (SPMSC1) MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 77

Chapter5 Resets, Interrupts, and System Configuration Table5-10. SPMSC1 Register Field Descriptions Field Description 7 Low-Voltage Warning Flag — The LVWF bit indicates the low-voltage warning status. LVWF 0 low-voltage warning is not present. 1 low-voltage warning is present or was present. 6 Low-Voltage Warning Acknowledge — If LVWF = 1, a low-voltage condition has occurred. To acknowledge LVWACK this low-voltage warning, write 1 to LVWACK, which will automatically clear LVWF to 0 if the low-voltage warning is no longer present. 5 Low-Voltage Warning Interrupt Enable — This bit enables hardware interrupt requests for LVWF. LVWIE 0 Hardware interrupt disabled (use polling). 1 Request a hardware interrupt when LVWF = 1. 4 Low-Voltage Detect Reset Enable — This write-once bit enables LVD events to generate a hardware reset LVDRE (provided LVDE = 1). 0 LVD events do not generate hardware resets. 1 Force an MCU reset when an enabled low-voltage detect event occurs. 3 Low-Voltage Detect Stop Enable — Provided LVDE = 1, this read/write bit determines whether the low-voltage LVDSE detect function operates when the MCU is in stop mode. 0 Low-voltage detect disabled during stop mode. 1 Low-voltage detect enabled during stop mode. 2 Low-Voltage Detect Enable — This write-once bit enables low-voltage detect logic and qualifies the operation LVDE of other bits in this register. 0 LVD logic disabled. 1 LVD logic enabled. 0 Bandgap Buffer Enable — This bit enables an internal buffer for the bandgap voltage reference for use by BGBE ACMP or ADC module on one of its internal channels. 0 Bandgap buffer disabled. 1 Bandgap buffer enabled. 5.7.8 System Power Management Status and Control 2 Register (SPMSC2) This register is used to report the status of the low voltage warning function, and to configure the stop mode behavior of the MCU. 7 6 5 4 3 2 1 0 R 0 0 PPDF 0 0 LVDV LVWV PPDC1 W PPDACK Power-on Reset: 0 0 0 0 0 0 0 0 LVD Reset: 0 0 u u 0 0 0 0 Any other Reset: 0 0 u u 0 0 0 0 = Unimplemented or Reserved u = Unaffected by reset 1 This bit can be written only one time after reset. Additional writes are ignored. Figure5-10. System Power Management Status and Control 2 Register (SPMSC2) MC9S08JM60 Series Data Sheet, Rev. 5 78 Freescale Semiconductor

Chapter5 Resets, Interrupts, and System Configuration Table5-11. SPMSC2 Register Field Descriptions Field Description 5 Low-Voltage Detect Voltage Select — This bit selects the low voltage detect (LVD) trip point setting.It also LVDV selects the warning voltage range. See Table5-12. 4 Low-Voltage Warning Voltage Select — This bit selects the low voltage warning (LVW) trip point voltage. See LVWV Table5-12. 3 Partial Power Down Flag — This read-only status bit indicates that the MCU has recovered from stop2 mode. PPDF 0 MCU has not recovered from stop2 mode. 1 MCU recovered from stop2 mode. 2 Partial Power Down Acknowledge — Writing a 1 to PPDACK clears the PPDF bit PPDACK 0 Partial Power Down Control — This write-once bit controls whether stop2 or stop3 mode is selected. PPDC 0 Stop3 mode enabled. 1 Stop2, partial power down, mode enabled. Table5-12. LVD and LVW trip point typical values1 LVDV:LVWV LVW Trip Point LVD Trip Point 0:0 V = 2.74 V V = 2.56 V LVW0 LVD0 0:1 V = 2.92 V LVW1 1:0 V = 4.3 V V = 4.0 V LVW2 LVD1 1:1 V = 4.6 V LVW3 1 See AppendixA, “Electrical Characteristics,” for minimum and maximum values. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 79

Chapter5 Resets, Interrupts, and System Configuration MC9S08JM60 Series Data Sheet, Rev. 5 80 Freescale Semiconductor

Chapter 6 Parallel Input/Output 6.1 Introduction This chapter explains software controls related to parallel input/output (I/O). The MC9S08JM60 has seven I/O ports which include a total of 51 general-purpose I/O pins. See Chapter 2, “Pins and Connections,” for more information about the logic and hardware aspects of these pins. Not all pins are available on all devices. See Table2-1 to determine which functions are available for a specific device. Many of the I/O pins are shared with on-chip peripheral functions, as shown in Table 2-1. The peripheral modules have priority over the I/Os, so when a peripheral is enabled, the I/O functions are disabled. After reset, the shared peripheral functions are disabled so that the pins are controlled by the parallel I/O. All of the parallel I/O are configured as inputs (PTxDDn = 0). The pin control functions for each pin are configured as follows: slew rate control enabled (PTxSEn = 1), low drive strength selected (PTxDSn = 0), and internal pullups disabled (PTxPEn = 0). NOTE Not all general-purpose I/O pins are available on all packages. To avoid extra current drain from floating input pins, the user’s reset initialization routine in the application program must either enable on-chip pullup devices or change the direction of unconnected pins to outputs so the pins do not float. 6.2 Port Data and Data Direction Reading and writing of parallel I/O is done through the port data registers. The direction, input or output, is controlled through the port data direction registers. The parallel I/O port function for an individual pin is illustrated in the block diagram below. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 81

Chapter6 Parallel Input/Output PTxDDn D Q Output Enable PTxDn D Q Output Data 1 Port Read Data 0 Synchronizer Input Data BUSCLK Figure6-1. Parallel I/O Block Diagram The data direction control bits determine whether the pin output driver is enabled, and they control what is read for port data register reads. Each port pin has a data direction register bit. When PTxDDn= 0, the corresponding pin is an input and reads of PTxD return the pin value. When PTxDDn= 1, the corresponding pin is an output and reads of PTxD return the last value written to the port data register. When a peripheral module or system function is in control of a port pin, the data direction register bit still controls what is returned for reads of the port data register, even though the peripheral system has overriding control of the actual pin direction. When a shared analog function is enabled for a pin, all digital pin functions are disabled. A read of the port data register returns a value of 0 for any bits which have shared analog functions enabled. In general, whenever a pin is shared with both an alternate digital function and an analog function, the analog function has priority such that if both the digital and analog functions are enabled, the analog function controls the pin. It is a good programming practice to write to the port data register before changing the direction of a port pin to become an output. This ensures that the pin will not be driven momentarily with an old data value that happened to be in the port data register. 6.3 Pin Control The pin control registers are located in the high page register block of the memory. These registers are used to control pullups, slew rate, and drive strength for the I/O pins. The pin control registers operate independently of the parallel I/O registers. MC9S08JM60 Series Data Sheet, Rev. 5 82 Freescale Semiconductor

Chapter6 Parallel Input/Output 6.3.1 Internal Pullup Enable An internal pullup device can be enabled for each port pin by setting the corresponding bit in one of the pullup enable registers (PTxPEn). The pullup device is disabled if the pin is configured as an output by the parallel I/O control logic or any shared peripheral function regardless of the state of the corresponding pullup enable register bit. The pullup device is also disabled if the pin is controlled by an analog function. 6.3.2 Output Slew Rate Control Enable Slew rate control can be enabled for each port pin by setting the corresponding bit in one of the slew rate control registers (PTxSEn). When enabled, slew control limits the rate at which an output can transition in order to reduce EMC emissions. Slew rate control has no effect on pins which are configured as inputs. 6.3.3 Output Drive Strength Select An output pin can be selected to have high output drive strength by setting the corresponding bit in one of the drive strength select registers (PTxDSn). When high drive is selected a pin is capable of sourcing and sinking greater current. Even though every I/O pin can be selected as high drive, the user must ensure that the total current source and sink limits for the chip are not exceeded. Drive strength selection is intended to affect the DC behavior of I/O pins. However, the AC behavior is also affected. High drive allows a pin to drive a greater load with the same switching speed as a low drive enabled pin into a smaller load. Because of this the EMC emissions may be affected by enabling pins as high drive. 6.4 Pin Behavior in Stop Modes Depending on the stop mode, I/O functions differently as the result of executing a STOP instruction. An explanation of I/O behavior for the various stop modes follows: • Stop2 mode is a partial power-down mode, whereby I/O latches are maintained in their state as before the STOP instruction was executed. CPU register status and the state of I/O registers must be saved in RAM before the STOP instruction is executed to place the MCU in stop2 mode. Upon recovery from stop2 mode, before accessing any I/O, the user must examine the state of the PPDF bit in the SPMSC2 register. If the PPDF bit is 0, I/O must be initialized as if a power on reset had occurred. If the PPDF bit is 1, I/O data previously stored in RAM, before the STOP instruction was executed, peripherals may require being initialized and restored to their pre-stop condition. The user must then write a 1 to the PPDACK bit in the SPMSC2 register. Access to I/O is now permitted again in the user’s application program. • In stop3 mode, all I/O is maintained because internal logic circuity stays powered up. Upon recovery, normal I/O function is available to the user. 6.5 Parallel I/O and Pin Control Registers This section provides information about the registers associated with the parallel I/O ports and pin control functions. These parallel I/O registers are located in page zero of the memory map and the pin control registers are located in the high page register section of memory. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 83

Chapter6 Parallel Input/Output Refer to tables in Chapter 4, “Memory,” for the absolute address assignments for all parallel I/O and pin control registers. This section refers to registers and control bits only by their names. A Freescale-provided equate or header file normally is used to translate these names into the appropriate absolute addresses. 6.5.1 Port A I/O Registers (PTAD and PTADD) Port A parallel I/O function is controlled by the registers listed below. 7 6 5 4 3 2 1 0 R PTAD5 PTAD4 PTAD3 PTAD2 PTAD1 PTAD0 W Reset 0 0 0 0 0 0 0 0 Figure6-2. Port A Data Register (PTAD) Table6-1. PTAD Register Field Descriptions Field Description 5:0 Port A Data Register Bits — For port A pins that are inputs, reads return the logic level on the pin. For port A PTAD[5:0] pins that are configured as outputs, reads return the last value written to this register. Writes are latched into all bits of this register. For port A pins that are configured as outputs, the logic level is driven out the corresponding MCU pin. Reset forces PTAD to all 0s, but these 0s are not driven out the corresponding pins because reset also configures all port pins as high-impedance inputs with pullups disabled. 7 6 5 4 3 2 1 0 R PTADD5 PTADD4 PTADD3 PTADD2 PTADD1 PTADD0 W Reset 0 0 0 0 0 0 0 0 Figure6-3. Data Direction for Port A Register (PTADD) Table6-2. PTADD Register Field Descriptions Field Description 5:0 Data Direction for Port A Bits — These read/write bits control the direction of port A pins and what is read for PTADD[5:0] PTAD reads. 0 Input (output driver disabled) and reads return the pin value. 1 Output driver enabled for port A bit n and PTAD reads return the contents of PTADn. 6.5.2 Port A Pin Control Registers (PTAPE, PTASE, PTADS) In addition to the I/O control, port A pins are controlled by the registers listed below. MC9S08JM60 Series Data Sheet, Rev. 5 84 Freescale Semiconductor

Chapter6 Parallel Input/Output 7 6 5 4 3 2 1 0 R PTAPE5 PTAPE4 PTAPE3 PTAPE2 PTAPE1 PTAPE0 W Reset 0 0 0 0 0 0 0 0 Figure6-4. Internal Pullup Enable for Port A (PTAPE) Table6-3. PTADD Register Field Descriptions Field Description [5:0] Internal Pullup Enable for Port A Bits — Each of these control bits determines if the internal pullup device is PTAPE[5:0] enabled for the associated PTA pin. For port A pins that are configured as outputs, these bits have no effect and the internal pullup devices are disabled. 0 Internal pullup device disabled for port A bit n. 1 Internal pullup device enabled for port A bit n. 7 6 5 4 3 2 1 0 R PTASE5 PTASE4 PTASE3 PTASE2 PTASE1 PTASE0 W Reset 0 0 1 1 1 1 1 1 Figure6-5. Output Slew Rate Control Enable for Port A (PTASE) Table6-4. PTASE Register Field Descriptions Field Description 5:0 Output Slew Rate Control Enable for Port A Bits — Each of these control bits determine whether output slew PTASE[5:0] rate control is enabled for the associated PTA pin. For port A pins that are configured as inputs, these bits have no effect. 0 Output slew rate control disabled for port A bit n. 1 Output slew rate control enabled for port A bit n. 7 6 5 4 3 2 1 0 R PTADS5 PTADS4 PTADS3 PTADS2 PTADS1 PTADS0 W Reset 0 0 0 0 0 0 0 0 Figure6-6. Output Drive Strength Selection for Port A (PTASE) Table6-5. PTASE Register Field Descriptions Field Description 5:0 Output Drive Strength Selection for Port A Bits — Each of these control bits selects between low and high PTADS[5:0] output drive for the associated PTA pin. 0 Low output drive enabled for port A bit n. 1 High output drive enabled for port A bit n. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 85

Chapter6 Parallel Input/Output 6.5.3 Port B I/O Registers (PTBD and PTBDD) Port B parallel I/O function is controlled by the registers listed below. 7 6 5 4 3 2 1 0 R PTBD7 PTBD6 PTBD5 PTBD4 PTBD3 PTBD2 PTBD1 PTBD0 W Reset 0 0 0 0 0 0 0 0 Figure6-7. Port B Data Register (PTBD) Table6-6. PTBD Register Field Descriptions Field Description 7:0 Port B Data Register Bits — For port B pins that are inputs, reads return the logic level on the pin. For port B PTBD[7:0] pins that are configured as outputs, reads return the last value written to this register. Writes are latched into all bits of this register. For port B pins that are configured as outputs, the logic level is driven out the corresponding MCU pin. Reset forces PTBD to all 0s, but these 0s are not driven out the corresponding pins because reset also configures all port pins as high-impedance inputs with pullups disabled. 7 6 5 4 3 2 1 0 R PTBDD7 PTBDD6 PTBDD5 PTBDD4 PTBDD3 PTBDD2 PTBDD1 PTBDD0 W Reset 0 0 0 0 0 0 0 0 Figure6-8. Data Direction for Port B (PTBDD) Table6-7. PTBDD Register Field Descriptions Field Description 7:0 Data Direction for Port B Bits — These read/write bits control the direction of port B pins and what is read for PTBDD[7:0] PTBD reads. 0 Input (output driver disabled) and reads return the pin value. 1 Output driver enabled for port B bit n and PTBD reads return the contents of PTBDn. 6.5.4 Port B Pin Control Registers (PTBPE, PTBSE, PTBDS) In addition to the I/O control, port B pins are controlled by the registers listed below. MC9S08JM60 Series Data Sheet, Rev. 5 86 Freescale Semiconductor

Chapter6 Parallel Input/Output 7 6 5 4 3 2 1 0 R PTBPE7 PTBPE6 PTBPE5 PTBPE4 PTBPE3 PTBPE2 PTBPE1 PTBPE0 W Reset 0 0 0 0 0 0 0 0 Figure6-9. Internal Pullup Enable for Port B (PTBPE) Table6-8. PTBPE Register Field Descriptions Field Description 7:0 Internal Pullup Enable for Port B Bits — Each of these control bits determines if the internal pullup device is PTBPE[7:0] enabled for the associated PTB pin. For port B pins that are configured as outputs, these bits have no effect and the internal pullup devices are disabled. 0 Internal pullup device disabled for port B bit n. 1 Internal pullup device enabled for port B bit n. 7 6 5 4 3 2 1 0 R PTBSE7 PTBSE6 PTBSE5 PTBSE4 PTBSE3 PTBSE2 PTBSE1 PTBSE0 W Reset 1 1 1 1 1 1 1 1 Figure6-10. Output Slew Rate Control Enable (PTBSE) Table6-9. PTBSE Register Field Descriptions Field Description 7:0 Output Slew Rate Control Enable for Port B Bits— Each of these control bits determine whether output slew PTBSE[7:0] rate control is enabled for the associated PTB pin. For port B pins that are configured as inputs, these bits have no effect. 0 Output slew rate control disabled for port B bit n. 1 Output slew rate control enabled for port B bit n. 7 6 5 4 3 2 1 0 R PTBDS7 PTBDS6 PTBDS5 PTBDS4 PTBDS3 PTBDS2 PTBDS1 PTBDS0 W Reset 0 0 0 0 0 0 0 0 Figure6-11. Output Drive Strength Selection for Port B (PTBDS) Table6-10. PTBDS Register Field Descriptions Field Description 7:0 Output Drive Strength Selection for Port B Bits — Each of these control bits selects between low and high PTBDS[7:0] output drive for the associated PTB pin. 0 Low output drive enabled for port B bit n. 1 High output drive enabled for port B bit n. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 87

Chapter6 Parallel Input/Output 6.5.5 Port C I/O Registers (PTCD and PTCDD) Port C parallel I/O function is controlled by the registers listed below. 7 6 5 4 3 2 1 0 R PTCD6 PTCD5 PTCD4 PTCD3 PTCD2 PTCD1 PTCD0 W Reset 0 0 0 0 0 0 0 0 Figure6-12. Port C Data Register (PTCD) Table6-11. PTCD Register Field Descriptions Field Description 6:0 Port C Data Register Bits — For port C pins that are inputs, reads return the logic level on the pin. For port C PTCD[6:0] pins that are configured as outputs, reads return the last value written to this register. Writes are latched into all bits of this register. For port C pins that are configured as outputs, the logic level is driven out the corresponding MCU pin. Reset forces PTCD to all 0s, but these 0s are not driven out the corresponding pins because reset also configures all port pins as high-impedance inputs with pullups disabled. 7 6 5 4 3 2 1 0 R PTCDD6 PTCDD5 PTCDD4 PTCDD3 PTCDD2 PTCDD1 PTCDD0 W Reset 0 0 0 0 0 0 0 0 Figure6-13. Data Direction for Port C (PTCDD) Table6-12. PTCDD Register Field Descriptions Field Description 6:0 Data Direction for Port C Bits — These read/write bits control the direction of port C pins and what is read for PTCDD[6:0] PTCD reads. 0 Input (output driver disabled) and reads return the pin value. 1 Output driver enabled for port C bit n and PTCD reads return the contents of PTCDn. 6.5.6 Port C Pin Control Registers (PTCPE, PTCSE, PTCDS) In addition to the I/O control, port C pins are controlled by the registers listed below. MC9S08JM60 Series Data Sheet, Rev. 5 88 Freescale Semiconductor

Chapter6 Parallel Input/Output 7 6 5 4 3 2 1 0 R PTCPE6 PTCPE5 PTCPE4 PTCPE3 PTCPE2 PTCPE1 PTCPE0 W Reset 0 0 0 0 0 0 0 0 Figure6-14. Internal Pullup Enable for Port C (PTCPE) Table6-13. PTCPE Register Field Descriptions Field Description 6:0 Internal Pullup Enable for Port C Bits — Each of these control bits determines if the internal pullup device is PTCPE[6:0] enabled for the associated PTC pin. For port C pins that are configured as outputs, these bits have no effect and the internal pullup devices are disabled. 0 Internal pullup device disabled for port C bit n. 1 Internal pullup device enabled for port C bit n. 7 6 5 4 3 2 1 0 R PTCSE6 PTCSE5 PTCSE4 PTCSE3 PTCSE2 PTCSE1 PTCSE0 W Reset 0 1 1 1 1 1 1 1 Figure6-15. Output Slew Rate Control Enable for Port C (PTCSE) Table6-14. PTCSE Register Field Descriptions Field Description 6:0 Output Slew Rate Control Enable for Port C Bits — Each of these control bits determine whether output slew PTCSE[6:0] rate control is enabled for the associated PTC pin. For port C pins that are configured as inputs, these bits have no effect. 0 Output slew rate control disabled for port C bit n. 1 Output slew rate control enabled for port C bit n. 7 6 5 4 3 2 1 0 R PTCDS6 PTCDS5 PTCDS4 PTCDS3 PTCDS2 PTCDS1 PTCDS0 W Reset 0 0 0 0 0 0 0 0 Figure6-16. Output Drive Strength Selection for Port C (PTCDS) Table6-15. PTCDS Register Field Descriptions Field Description 6:0 Output Drive Strength Selection for Port C Bits — Each of these control bits selects between low and high PTCDS[6:0] output drive for the associated PTC pin. 0 Low output drive enabled for port C bit n. 1 High output drive enabled for port C bit n. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 89

Chapter6 Parallel Input/Output 6.5.7 Port D I/O Registers (PTDD and PTDDD) Port D parallel I/O function is controlled by the registers listed below. 7 6 5 4 3 2 1 0 R PTDD7 PTDD6 PTDD5 PTDD4 PTDD3 PTDD2 PTDD1 PTDD0 W Reset 0 0 0 0 0 0 0 0 Figure6-17. Port D Data Register (PTDD) Table6-16. PTDD Register Field Descriptions Field Description 7:0 Port D Data Register Bits — For port D pins that are inputs, reads return the logic level on the pin. For port D PTDD[7:0] pins that are configured as outputs, reads return the last value written to this register. Writes are latched into all bits of this register. For port D pins that are configured as outputs, the logic level is driven out the corresponding MCU pin. Reset forces PTDD to all 0s, but these 0s are not driven out the corresponding pins because reset also configures all port pins as high-impedance inputs with pullups disabled. 7 6 5 4 3 2 1 0 R PTDDD7 PTDDD6 PTDDD5 PTDDD4 PTDDD3 PTDDD2 PTDDD1 PTDDD0 W Reset 0 0 0 0 0 0 0 0 Figure6-18. Data Direction for Port D (PTDDD) Table6-17. PTDDD Register Field Descriptions Field Description 7:0 Data Direction for Port D Bits — These read/write bits control the direction of port D pins and what is read for PTDDD[7:0] PTDD reads. 0 Input (output driver disabled) and reads return the pin value. 1 Output driver enabled for port D bit n and PTDD reads return the contents of PTDDn. 6.5.8 Port D Pin Control Registers (PTDPE, PTDSE, PTDDS) In addition to the I/O control, port D pins are controlled by the registers listed below. MC9S08JM60 Series Data Sheet, Rev. 5 90 Freescale Semiconductor

Chapter6 Parallel Input/Output 7 6 5 4 3 2 1 0 R PTDPE7 PTDPE6 PTDPE5 PTDPE4 PTDPE3 PTDPE2 PTDPE1 PTDPE0 W Reset 0 0 0 0 0 0 0 0 Figure6-19. Internal Pullup Enable for Port D (PTDPE) Table6-18. PTDPE Register Field Descriptions Field Description 7:0 Internal Pullup Enable for Port D Bits — Each of these control bits determines if the internal pullup device is PTDPE[7:0] enabled for the associated PTD pin. For port D pins that are configured as outputs, these bits have no effect and the internal pullup devices are disabled. 0 Internal pullup device disabled for port D bit n. 1 Internal pullup device enabled for port D bit n. 7 6 5 4 3 2 1 0 R PTDSE7 PTDSE6 PTDSE5 PTDSE4 PTDSE3 PTDSE2 PTDSE1 PTDSE0 W Reset 1 1 1 1 1 1 1 1 Figure6-20. Output Slew Rate Control Enable for Port D (PTDSE) Table6-19. PTDSE Register Field Descriptions Field Description 7:0 Output Slew Rate Control Enable for Port D Bits — Each of these control bits determine whether output slew PTDSE[7:0] rate control is enabled for the associated PTD pin. For port D pins that are configured as inputs, these bits have no effect. 0 Output slew rate control disabled for port D bit n. 1 Output slew rate control enabled for port D bit n. 7 6 5 4 3 2 1 0 R PTDDS7 PTDDS6 PTDDS5 PTDDS4 PTDDS3 PTDDS2 PTDDS1 PTDDS0 W Reset 0 0 0 0 0 0 0 0 Figure6-21. Output Drive Strength Selection for Port D (PTDDS) Table6-20. PTDDS Register Field Descriptions Field Description 7:0 Output Drive Strength Selection for Port D Bits — Each of these control bits selects between low and high PTDDS[7:0] output drive for the associated PTD pin. 0 Low output drive enabled for port D bit n. 1 High output drive enabled for port D bit n. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 91

Chapter6 Parallel Input/Output 6.5.9 Port E I/O Registers (PTED and PTEDD) Port E parallel I/O function is controlled by the registers listed below. 7 6 5 4 3 2 1 0 R PTED7 PTED6 PTED5 PTED4 PTED3 PTED2 PTED1 PTED0 W Reset 0 0 0 0 0 0 0 0 Figure6-22. Port E Data Register (PTED) Table6-21. PTED Register Field Descriptions Field Description 7:0 Port E Data Register Bits — For port E pins that are inputs, reads return the logic level on the pin. For port E PTED[7:0] pins that are configured as outputs, reads return the last value written to this register. Writes are latched into all bits of this register. For port E pins that are configured as outputs, the logic level is driven out the corresponding MCU pin. Reset forces PTED to all 0s, but these 0s are not driven out the corresponding pins because reset also configures all port pins as high-impedance inputs with pullups disabled. 7 6 5 4 3 2 1 0 R PTEDD7 PTEDD6 PTEDD5 PTEDD4 PTEDD3 PTEDD2 PTEDD1 PTEDD0 W Reset 0 0 0 0 0 0 0 0 Figure6-23. Data Direction for Port E (PTEDD) Table6-22. PTEDD Register Field Descriptions Field Description 7:0 Data Direction for Port E Bits — These read/write bits control the direction of port E pins and what is read for PTEDD[7:0] PTED reads. 0 Input (output driver disabled) and reads return the pin value. 1 Output driver enabled for port E bit n and PTED reads return the contents of PTEDn. 6.5.10 Port E Pin Control Registers (PTEPE, PTESE, PTEDS) In addition to the I/O control, port E pins are controlled by the registers listed below. MC9S08JM60 Series Data Sheet, Rev. 5 92 Freescale Semiconductor

Chapter6 Parallel Input/Output 7 6 5 4 3 2 1 0 R PTEPE7 PTEPE6 PTEPE5 PTEPE4 PTEPE3 PTEPE2 PTEPE1 PTEPE0 W Reset 0 0 0 0 0 0 0 0 Figure6-24. Internal Pullup Enable for Port E (PTEPE) Table6-23. PTEPE Register Field Descriptions Field Description 7:0 Internal Pullup Enable for Port E Bits— Each of these control bits determines if the internal pullup device is PTEPE[7:0] enabled for the associated PTE pin. For port E pins that are configured as outputs, these bits have no effect and the internal pullup devices are disabled. 0 Internal pullup device disabled for port E bit n. 1 Internal pullup device enabled for port E bit n. 7 6 5 4 3 2 1 0 R PTESE7 PTESE6 PTESE5 PTESE4 PTESE3 PTESE2 PTESE1 PTESE0 W Reset 1 1 1 1 1 1 1 1 Figure6-25. Output Slew Rate Control Enable for Port E (PTESE) Table6-24. PTESE Register Field Descriptions Field Description 7:0 Output Slew Rate Control Enable for Port E Bits — Each of these control bits determine whether output slew PTESE[7:0] rate control is enabled for the associated PTE pin. For port E pins that are configured as inputs, these bits have no effect. 0 Output slew rate control disabled for port E bit n. 1 Output slew rate control enabled for port E bit n. 7 6 5 4 3 2 1 0 R PTEDS7 PTEDS6 PTEDS5 PTEDS4 PTEDS3 PTEDS2 PTEDS1 PTEDS0 W Reset 0 0 0 0 0 0 0 0 Figure6-26. Output Drive Strength Selection for Port E (PTEDS) Table6-25. PTEDS Register Field Descriptions Field Description 7:0 Output Drive Strength Selection for Port E Bits — Each of these control bits selects between low and high PTEDS[7:0] output drive for the associated PTE pin. 0 Low output drive enabled for port E bit n. 1 High output drive enabled for port E bit n. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 93

Chapter6 Parallel Input/Output 6.5.11 Port F I/O Registers (PTFD and PTFDD) Port F parallel I/O function is controlled by the registers listed below. 7 6 5 4 3 2 1 0 R PTFD7 PTFD6 PTFD5 PTFD4 PTFD3 PTFD2 PTFD1 PTFD0 W Reset 0 0 0 0 0 0 0 0 Figure6-27. Port F Data Register (PTFD) Table6-26. PTFD Register Field Descriptions Field Description 7:0 Port F Data Register Bits— For port F pins that are inputs, reads return the logic level on the pin. For port F PTFD[7:0] pins that are configured as outputs, reads return the last value written to this register. Writes are latched into all bits of this register. For port F pins that are configured as outputs, the logic level is driven out the corresponding MCU pin. Reset forces PTFD to all 0s, but these 0s are not driven out the corresponding pins because reset also configures all port pins as high-impedance inputs with pullups disabled. 7 6 5 4 3 2 1 0 R PTFDD7 PTFDD6 PTFDD5 PTFDD4 PTFDD3 PTFDD2 PTFDD1 PTFDD0 W Reset 0 0 0 0 0 0 0 0 Figure6-28. Data Direction for Port F (PTFDD) Table6-27. PTFDD Register Field Descriptions Field Description 7:0 Data Direction for Port F Bits — These read/write bits control the direction of port F pins and what is read for PTFDD[7:0] PTFD reads. 0 Input (output driver disabled) and reads return the pin value. 1 Output driver enabled for port F bit n and PTFD reads return the contents of PTFDn. 6.5.12 Port F Pin Control Registers (PTFPE, PTFSE, PTFDS) In addition to the I/O control, port F pins are controlled by the registers listed below. MC9S08JM60 Series Data Sheet, Rev. 5 94 Freescale Semiconductor

Chapter6 Parallel Input/Output 7 6 5 4 3 2 1 0 R PTFPE7 PTFPE6 PTFPE5 PTFPE4 PTFPE3 PTFPE2 PTFPE1 PTFPE0 W Reset 0 0 0 0 0 0 0 0 Figure6-29. Internal Pullup Enable for Port F (PTFPE) Table6-28. PTFPE Register Field Descriptions Field Description 7:0 Internal Pullup Enable for Port F Bits — Each of these control bits determines if the internal pullup device is PTFPE[7:0] enabled for the associated PTF pin. For port F pins that are configured as outputs, these bits have no effect and the internal pullup devices are disabled. 0 Internal pullup device disabled for port F bit n. 1 Internal pullup device enabled for port F bit n. 7 6 5 4 3 2 1 0 R PTFSE7 PTFSE6 PTFSE5 PTFSE4 PTFSE3 PTFSE2 PTFSE1 PTFSE0 W Reset 1 1 1 1 1 1 1 1 Figure6-30. Output Slew Rate Control Enable for Port F (PTFSE) Table6-29. PTFSE Register Field Descriptions Field Description 7:0 Output Slew Rate Control Enable for Port F Bits — Each of these control bits determine whether output slew PTFSE[7:0] rate control is enabled for the associated PTF pin. For port F pins that are configured as inputs, these bits have no effect. 0 Output slew rate control disabled for port F bit n. 1 Output slew rate control enabled for port F bit n. 7 6 5 4 3 2 1 0 R PTFDS7 PTFDS6 PTFDS5 PTFDS4 PTFDS3 PTFDS2 PTFDS1 PTFDS0 W Reset 0 0 0 0 0 0 0 0 Figure6-31. Output Drive Strength Selection for Port F (PTFDS) Table6-30. PTFDS Register Field Descriptions Field Description 7:0 Output Drive Strength Selection for Port F Bits — Each of these control bits selects between low and high PTFDS[7:0] output drive for the associated PTF pin. 0 Low output drive enabled for port F bit n. 1 High output drive enabled for port F bit n. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 95

Chapter6 Parallel Input/Output 6.5.13 Port G I/O Registers (PTGD and PTGDD) Port G parallel I/O function is controlled by the registers listed below. 7 6 5 4 3 2 1 0 R PTGD5 PTGD4 PTGD3 PTGD2 PTGD1 PTGD0 W Reset 0 0 0 0 0 0 0 0 Figure6-32. Port G Data Register (PTGD) Table6-31. PTGD Register Field Descriptions Field Description 5:0 Port G Data Register Bits — For port G pins that are inputs, reads return the logic level on the pin. For port G PTGD[5:0] pins that are configured as outputs, reads return the last value written to this register. Writes are latched into all bits of this register. For port G pins that are configured as outputs, the logic level is driven out the corresponding MCU pin. Reset forces PTGD to all 0s, but these 0s are not driven out the corresponding pins because reset also configures all port pins as high-impedance inputs with pullups disabled. 7 6 5 4 3 2 1 0 R PTGDD5 PTGDD4 PTGDD3 PTGDD2 PTGDD1 PTGDD0 W Reset 0 0 0 0 0 0 0 0 Figure6-33. Data Direction for Port G (PTGDD) Table6-32. PTGDD Register Field Descriptions Field Description 5:0 Data Direction for Port G Bits — These read/write bits control the direction of port G pins and what is read for PTGDD[5:0] PTGD reads. 0 Input (output driver disabled) and reads return the pin value. 1 Output driver enabled for port G bit n and PTGD reads return the contents of PTGDn. 6.5.14 Port G Pin Control Registers (PTGPE, PTGSE, PTGDS) In addition to the I/O control, port G pins are controlled by the registers listed below. MC9S08JM60 Series Data Sheet, Rev. 5 96 Freescale Semiconductor

Chapter6 Parallel Input/Output 7 6 5 4 3 2 1 0 R PTGPE5 PTGPE4 PTGPE3 PTGPE2 PTGPE1 PTGPE0 W Reset 0 0 0 0 0 0 0 0 Figure6-34. Internal Pullup Enable for Port G Bits (PTGPE) Table6-33. PTGPE Register Field Descriptions Field Description 5:0 Internal Pullup Enable for Port G Bits — Each of these control bits determines if the internal pullup device is PTGPEn enabled for the associated PTG pin. For port G pins that are configured as outputs, these bits have no effect and the internal pullup devices are disabled. 0 Internal pullup device disabled for port G bit n. 1 Internal pullup device enabled for port G bit n. 7 6 5 4 3 2 1 0 R PTGSE5 PTGSE4 PTGSE3 PTGSE2 PTGSE1 PTGSE0 W Reset 0 1 1 1 1 1 1 1 Figure6-35. Output Slew Rate Control Enable for Port G Bits (PTGSE) Table6-34. PTGSE Register Field Descriptions Field Description 5:0 Output Slew Rate Control Enable for Port G Bits— Each of these control bits determine whether output slew PTGSEn rate control is enabled for the associated PTG pin. For port G pins that are configured as inputs, these bits have no effect. 0 Output slew rate control disabled for port G bit n. 1 Output slew rate control enabled for port G bit n. 7 6 5 4 3 2 1 0 R PTGDS5 PTGDS4 PTGDS3 PTGDS2 PTGDS1 PTGDS0 W Reset 0 0 0 0 0 0 0 0 Figure6-36. Output Drive Strength Selection for Port G (PTGDS) Table6-35. PTGDS Register Field Descriptions Field Description 5:0 Output Drive Strength Selection for Port G Bits — Each of these control bits selects between low and high PTGDSn output drive for the associated PTG pin. 0 Low output drive enabled for port G bit n. 1 High output drive enabled for port G bit n. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 97

Chapter6 Parallel Input/Output MC9S08JM60 Series Data Sheet, Rev. 5 98 Freescale Semiconductor

Chapter 7 Central Processor Unit (S08CPUV2) 7.1 Introduction This section provides summary information about the registers, addressing modes, and instruction set of the CPU of the HCS08 Family. For a more detailed discussion, refer to the HCS08 Family Reference Manual, volume 1, Freescale Semiconductor document order number HCS08RMV1/D. The HCS08 CPU is fully source- and object-code-compatible with the M68HC08 CPU. Several instructions and enhanced addressing modes were added to improve C compiler efficiency and to support a new background debug system which replaces the monitor mode of earlier M68HC08 microcontrollers (MCU). 7.1.1 Features Features of the HCS08 CPU include: • Object code fully upward-compatible with M68HC05 and M68HC08 Families • All registers and memory are mapped to a single 64-Kbyte address space • 16-bit stack pointer (any size stack anywhere in 64-Kbyte address space) • 16-bit index register (H:X) with powerful indexed addressing modes • 8-bit accumulator (A) • Many instructions treat X as a second general-purpose 8-bit register • Seven addressing modes: — Inherent — Operands in internal registers — Relative — 8-bit signed offset to branch destination — Immediate — Operand in next object code byte(s) — Direct — Operand in memory at 0x0000–0x00FF — Extended — Operand anywhere in 64-Kbyte address space — Indexed relative to H:X — Five submodes including auto increment — Indexed relative to SP — Improves C efficiency dramatically • Memory-to-memory data move instructions with four address mode combinations • Overflow, half-carry, negative, zero, and carry condition codes support conditional branching on the results of signed, unsigned, and binary-coded decimal (BCD) operations • Efficient bit manipulation instructions • Fast 8-bit by 8-bit multiply and 16-bit by 8-bit divide instructions • STOP and WAIT instructions to invoke low-power operating modes MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 99

Chapter7 Central Processor Unit (S08CPUV2) 7.2 Programmer’s Model and CPU Registers Figure 7-1 shows the five CPU registers. CPU registers are not part of the memory map. 7 0 ACCUMULATOR A 16-BIT INDEX REGISTER H:X H INDEX REGISTER (HIGH) INDEX REGISTER (LOW) X 15 8 7 0 STACK POINTER SP 15 0 PROGRAM COUNTER PC 7 0 CONDITION CODE REGISTER V 1 1 H I N Z C CCR CARRY ZERO NEGATIVE INTERRUPT MASK HALF-CARRY (FROM BIT 3) TWO’S COMPLEMENT OVERFLOW Figure7-1. CPU Registers 7.2.1 Accumulator (A) The A accumulator is a general-purpose 8-bit register. One operand input to the arithmetic logic unit (ALU) is connected to the accumulator and the ALU results are often stored into the A accumulator after arithmetic and logical operations. The accumulator can be loaded from memory using various addressing modes to specify the address where the loaded data comes from, or the contents of A can be stored to memory using various addressing modes to specify the address where data from A will be stored. Reset has no effect on the contents of the A accumulator. 7.2.2 Index Register (H:X) This 16-bit register is actually two separate 8-bit registers (H and X), which often work together as a 16-bit address pointer where H holds the upper byte of an address and X holds the lower byte of the address. All indexed addressing mode instructions use the full 16-bit value in H:X as an index reference pointer; however, for compatibility with the earlier M68HC05 Family, some instructions operate only on the low-order 8-bit half (X). Many instructions treat X as a second general-purpose 8-bit register that can be used to hold 8-bit data values. X can be cleared, incremented, decremented, complemented, negated, shifted, or rotated. Transfer instructions allow data to be transferred from A or transferred to A where arithmetic and logical operations can then be performed. For compatibility with the earlier M68HC05 Family, H is forced to 0x00 during reset. Reset has no effect on the contents of X. MC9S08JM60 Series Data Sheet, Rev. 5 100 Freescale Semiconductor

Chapter7 Central Processor Unit (S08CPUV2) 7.2.3 Stack Pointer (SP) This 16-bit address pointer register points at the next available location on the automatic last-in-first-out (LIFO) stack. The stack may be located anywhere in the 64-Kbyte address space that has RAM and can be any size up to the amount of available RAM. The stack is used to automatically save the return address for subroutine calls, the return address and CPU registers during interrupts, and for local variables. The AIS (add immediate to stack pointer) instruction adds an 8-bit signed immediate value to SP. This is most often used to allocate or deallocate space for local variables on the stack. SP is forced to 0x00FF at reset for compatibility with the earlier M68HC05 Family. HCS08 programs normally change the value in SP to the address of the last location (highest address) in on-chip RAM during reset initialization to free up direct page RAM (from the end of the on-chip registers to 0x00FF). The RSP (reset stack pointer) instruction was included for compatibility with the M68HC05 Family and is seldom used in new HCS08 programs because it only affects the low-order half of the stack pointer. 7.2.4 Program Counter (PC) The program counter is a 16-bit register that contains the address of the next instruction or operand to be fetched. During normal program execution, the program counter automatically increments to the next sequential memory location every time an instruction or operand is fetched. Jump, branch, interrupt, and return operations load the program counter with an address other than that of the next sequential location. This is called a change-of-flow. During reset, the program counter is loaded with the reset vector that is located at 0xFFFE and 0xFFFF. The vector stored there is the address of the first instruction that will be executed after exiting the reset state. 7.2.5 Condition Code Register (CCR) The 8-bit condition code register contains the interrupt mask (I) and five flags that indicate the results of the instruction just executed. Bits 6 and 5 are set permanently to 1. The following paragraphs describe the functions of the condition code bits in general terms. For a more detailed explanation of how each instruction sets the CCR bits, refer to the HCS08 Family Reference Manual, volume 1, Freescale Semiconductor document order number HCS08RMv1. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 101

Chapter7 Central Processor Unit (S08CPUV2) 7 0 CONDITION CODE REGISTER V 1 1 H I N Z C CCR CARRY ZERO NEGATIVE INTERRUPT MASK HALF-CARRY (FROM BIT 3) TWO’S COMPLEMENT OVERFLOW Figure7-2. Condition Code Register Table7-1. CCR Register Field Descriptions Field Description 7 Two’s Complement Overflow Flag — The CPU sets the overflow flag when a two’s complement overflow occurs. V The signed branch instructions BGT, BGE, BLE, and BLT use the overflow flag. 0 No overflow 1 Overflow 4 Half-Carry Flag — The CPU sets the half-carry flag when a carry occurs between accumulator bits 3 and 4 during H an add-without-carry (ADD) or add-with-carry (ADC) operation. The half-carry flag is required for binary-coded decimal (BCD) arithmetic operations. The DAA instruction uses the states of the H and C condition code bits to automatically add a correction value to the result from a previous ADD or ADC on BCD operands to correct the result to a valid BCD value. 0 No carry between bits 3 and 4 1 Carry between bits 3 and 4 3 Interrupt Mask Bit — When the interrupt mask is set, all maskable CPU interrupts are disabled. CPU interrupts I are enabled when the interrupt mask is cleared. When a CPU interrupt occurs, the interrupt mask is set automatically after the CPU registers are saved on the stack, but before the first instruction of the interrupt service routine is executed. Interrupts are not recognized at the instruction boundary after any instruction that clears I (CLI or TAP). This ensures that the next instruction after a CLI or TAP will always be executed without the possibility of an intervening interrupt, provided I was set. 0 Interrupts enabled 1 Interrupts disabled 2 Negative Flag — The CPU sets the negative flag when an arithmetic operation, logic operation, or data N manipulation produces a negative result, setting bit7 of the result. Simply loading or storing an 8-bit or 16-bit value causes N to be set if the most significant bit of the loaded or stored value was 1. 0 Non-negative result 1 Negative result 1 Zero Flag — The CPU sets the zero flag when an arithmetic operation, logic operation, or data manipulation Z produces a result of 0x00 or 0x0000. Simply loading or storing an 8-bit or 16-bit value causes Z to be set if the loaded or stored value was all 0s. 0 Non-zero result 1 Zero result 0 Carry/Borrow Flag — The CPU sets the carry/borrow flag when an addition operation produces a carry out of bit C 7 of the accumulator or when a subtraction operation requires a borrow. Some instructions — such as bit test and branch, shift, and rotate — also clear or set the carry/borrow flag. 0 No carry out of bit 7 1 Carry out of bit 7 MC9S08JM60 Series Data Sheet, Rev. 5 102 Freescale Semiconductor

Chapter7 Central Processor Unit (S08CPUV2) 7.3 Addressing Modes Addressing modes define the way the CPU accesses operands and data. In the HCS08, all memory, status and control registers, and input/output (I/O) ports share a single 64-Kbyte linear address space so a 16-bit binary address can uniquely identify any memory location. This arrangement means that the same instructions that access variables in RAM can also be used to access I/O and control registers or nonvolatile program space. Some instructions use more than one addressing mode. For instance, move instructions use one addressing mode to specify the source operand and a second addressing mode to specify the destination address. Instructions such as BRCLR, BRSET, CBEQ, and DBNZ use one addressing mode to specify the location of an operand for a test and then use relative addressing mode to specify the branch destination address when the tested condition is true. For BRCLR, BRSET, CBEQ, and DBNZ, the addressing mode listed in the instruction set tables is the addressing mode needed to access the operand to be tested, and relative addressing mode is implied for the branch destination. 7.3.1 Inherent Addressing Mode (INH) In this addressing mode, operands needed to complete the instruction (if any) are located within CPU registers so the CPU does not need to access memory to get any operands. 7.3.2 Relative Addressing Mode (REL) Relative addressing mode is used to specify the destination location for branch instructions. A signed 8-bit offset value is located in the memory location immediately following the opcode. During execution, if the branch condition is true, the signed offset is sign-extended to a 16-bit value and is added to the current contents of the program counter, which causes program execution to continue at the branch destination address. 7.3.3 Immediate Addressing Mode (IMM) In immediate addressing mode, the operand needed to complete the instruction is included in the object code immediately following the instruction opcode in memory. In the case of a 16-bit immediate operand, the high-order byte is located in the next memory location after the opcode, and the low-order byte is located in the next memory location after that. 7.3.4 Direct Addressing Mode (DIR) In direct addressing mode, the instruction includes the low-order eight bits of an address in the direct page (0x0000–0x00FF). During execution a 16-bit address is formed by concatenating an implied 0x00 for the high-order half of the address and the direct address from the instruction to get the 16-bit address where the desired operand is located. This is faster and more memory efficient than specifying a complete 16-bit address for the operand. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 103

Chapter7 Central Processor Unit (S08CPUV2) 7.3.5 Extended Addressing Mode (EXT) In extended addressing mode, the full 16-bit address of the operand is located in the next two bytes of program memory after the opcode (high byte first). 7.3.6 Indexed Addressing Mode Indexed addressing mode has seven variations including five that use the 16-bit H:X index register pair and two that use the stack pointer as the base reference. 7.3.6.1 Indexed, No Offset (IX) This variation of indexed addressing uses the 16-bit value in the H:X index register pair as the address of the operand needed to complete the instruction. 7.3.6.2 Indexed, No Offset with Post Increment (IX+) This variation of indexed addressing uses the 16-bit value in the H:X index register pair as the address of the operand needed to complete the instruction. The index register pair is then incremented (H:X =H:X+ 0x0001) after the operand has been fetched. This addressing mode is only used for MOV and CBEQ instructions. 7.3.6.3 Indexed, 8-Bit Offset (IX1) This variation of indexed addressing uses the 16-bit value in the H:X index register pair plus an unsigned 8-bit offset included in the instruction as the address of the operand needed to complete the instruction. 7.3.6.4 Indexed, 8-Bit Offset with Post Increment (IX1+) This variation of indexed addressing uses the 16-bit value in the H:X index register pair plus an unsigned 8-bit offset included in the instruction as the address of the operand needed to complete the instruction. The index register pair is then incremented (H:X= H:X+ 0x0001) after the operand has been fetched. This addressing mode is used only for the CBEQ instruction. 7.3.6.5 Indexed, 16-Bit Offset (IX2) This variation of indexed addressing uses the 16-bit value in the H:X index register pair plus a 16-bit offset included in the instruction as the address of the operand needed to complete the instruction. 7.3.6.6 SP-Relative, 8-Bit Offset (SP1) This variation of indexed addressing uses the 16-bit value in the stack pointer (SP) plus an unsigned 8-bit offset included in the instruction as the address of the operand needed to complete the instruction. MC9S08JM60 Series Data Sheet, Rev. 5 104 Freescale Semiconductor

Chapter7 Central Processor Unit (S08CPUV2) 7.3.6.7 SP-Relative, 16-Bit Offset (SP2) This variation of indexed addressing uses the 16-bit value in the stack pointer (SP) plus a 16-bit offset included in the instruction as the address of the operand needed to complete the instruction. 7.4 Special Operations The CPU performs a few special operations that are similar to instructions but do not have opcodes like other CPU instructions. In addition, a few instructions such as STOP and WAIT directly affect other MCU circuitry. This section provides additional information about these operations. 7.4.1 Reset Sequence Reset can be caused by a power-on-reset (POR) event, internal conditions such as the COP (computer operating properly) watchdog, or by assertion of an external active-low reset pin. When a reset event occurs, the CPU immediately stops whatever it is doing (the MCU does not wait for an instruction boundary before responding to a reset event). For a more detailed discussion about how the MCU recognizes resets and determines the source, refer to the Resets, Interrupts, and System Configuration chapter. The reset event is considered concluded when the sequence to determine whether the reset came from an internal source is done and when the reset pin is no longer asserted. At the conclusion of a reset event, the CPU performs a 6-cycle sequence to fetch the reset vector from 0xFFFE and 0xFFFF and to fill the instruction queue in preparation for execution of the first program instruction. 7.4.2 Interrupt Sequence When an interrupt is requested, the CPU completes the current instruction before responding to the interrupt. At this point, the program counter is pointing at the start of the next instruction, which is where the CPU should return after servicing the interrupt. The CPU responds to an interrupt by performing the same sequence of operations as for a software interrupt (SWI) instruction, except the address used for the vector fetch is determined by the highest priority interrupt that is pending when the interrupt sequence started. The CPU sequence for an interrupt is: 1. Store the contents of PCL, PCH, X, A, and CCR on the stack, in that order. 2. Set the I bit in the CCR. 3. Fetch the high-order half of the interrupt vector. 4. Fetch the low-order half of the interrupt vector. 5. Delay for one free bus cycle. 6. Fetch three bytes of program information starting at the address indicated by the interrupt vector to fill the instruction queue in preparation for execution of the first instruction in the interrupt service routine. After the CCR contents are pushed onto the stack, the I bit in the CCR is set to prevent other interrupts while in the interrupt service routine. Although it is possible to clear the I bit with an instruction in the MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 105

Chapter7 Central Processor Unit (S08CPUV2) interrupt service routine, this would allow nesting of interrupts (which is not recommended because it leads to programs that are difficult to debug and maintain). For compatibility with the earlier M68HC05 MCUs, the high-order half of the H:X index register pair (H) is not saved on the stack as part of the interrupt sequence. The user must use a PSHH instruction at the beginning of the service routine to save H and then use a PULH instruction just before the RTI that ends the interrupt service routine. It is not necessary to save H if you are certain that the interrupt service routine does not use any instructions or auto-increment addressing modes that might change the value of H. The software interrupt (SWI) instruction is like a hardware interrupt except that it is not masked by the global I bit in the CCR and it is associated with an instruction opcode within the program so it is not asynchronous to program execution. 7.4.3 Wait Mode Operation The WAIT instruction enables interrupts by clearing the I bit in the CCR. It then halts the clocks to the CPU to reduce overall power consumption while the CPU is waiting for the interrupt or reset event that will wake the CPU from wait mode. When an interrupt or reset event occurs, the CPU clocks will resume and the interrupt or reset event will be processed normally. If a serial BACKGROUND command is issued to the MCU through the background debug interface while the CPU is in wait mode, CPU clocks will resume and the CPU will enter active background mode where other serial background commands can be processed. This ensures that a host development system can still gain access to a target MCU even if it is in wait mode. 7.4.4 Stop Mode Operation Usually, all system clocks, including the crystal oscillator (when used), are halted during stop mode to minimize power consumption. In such systems, external circuitry is needed to control the time spent in stop mode and to issue a signal to wake up the target MCU when it is time to resume processing. Unlike the earlier M68HC05 and M68HC08 MCUs, the HCS08 can be configured to keep a minimum set of clocks running in stop mode. This optionally allows an internal periodic signal to wake the target MCU fromstop mode. When a host debug system is connected to the background debug pin (BKGD) and the ENBDM control bit has been set by a serial command through the background interface (or because the MCU was reset into active background mode), the oscillator is forced to remain active when the MCU enters stop mode. In this case, if a serial BACKGROUND command is issued to the MCU through the background debug interface while the CPU is in stop mode, CPU clocks will resume and the CPU will enter active background mode where other serial background commands can be processed. This ensures that a host development system can still gain access to a target MCU even if it is in stop mode. Recovery from stop mode depends on the particular HCS08 and whether the oscillator was stopped in stop mode. Refer to the Modes of Operation chapter for more details. MC9S08JM60 Series Data Sheet, Rev. 5 106 Freescale Semiconductor

Chapter7 Central Processor Unit (S08CPUV2) 7.4.5 BGND Instruction The BGND instruction is new to the HCS08 compared to the M68HC08. BGND would not be used in normal user programs because it forces the CPU to stop processing user instructions and enter the active background mode. The only way to resume execution of the user program is through reset or by a host debug system issuing a GO, TRACE1, or TAGGO serial command through the background debug interface. Software-based breakpoints can be set by replacing an opcode at the desired breakpoint address with the BGND opcode. When the program reaches this breakpoint address, the CPU is forced to active background mode rather than continuing the user program. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 107

Chapter7 Central Processor Unit (S08CPUV2) 7.5 HCS08 Instruction Set Summary Table 7-2 provides a summary of the HCS08 instruction set in all possible addressing modes. The table shows operand construction, execution time in internal bus clock cycles, and cycle-by-cycle details for each addressing mode variation of each instruction. Table7-2. . Instruction Set Summary (Sheet 1 of 9) s Affect SFoourrmce Operation AddresMode Object Code Cycles CyDc-ebtayi-lCsyc VHonI CNC ZR C ADC #opr8i IMM A9 ii 2 pp ADC opr8a DIR B9 dd 3 rpp ADC opr16a EXT C9 hh ll 4 prpp ADC oprx16,X Add with Carry IX2 D9 ee ff 4 prpp (cid:166) (cid:166) – (cid:166) (cid:166) (cid:166) ADC oprx8,X A ← (A) + (M) + (C) IX1 E9 ff 3 rpp ADC ,X IX F9 3 rfp ADC oprx16,SP SP2 9E D9 ee ff 5 pprpp ADC oprx8,SP SP1 9E E9 ff 4 prpp ADD #opr8i IMM AB ii 2 pp ADD opr8a DIR BB dd 3 rpp ADD opr16a EXT CB hh ll 4 prpp ADD oprx16,X Add without Carry IX2 DB ee ff 4 prpp (cid:166) (cid:166) – (cid:166) (cid:166) (cid:166) ADD oprx8,X A ← (A) + (M) IX1 EB ff 3 rpp ADD ,X IX FB 3 rfp ADD oprx16,SP SP2 9E DB ee ff 5 pprpp ADD oprx8,SP SP1 9E EB ff 4 prpp Add Immediate Value (Signed) to AIS #opr8i StackPointer IMM A7 ii 2 pp – – – – – – SP ← (SP) + (M) Add Immediate Value (Signed) to AIX #opr8i IndexRegister (H:X) IMM AF ii 2 pp – – – – – – H:X ← (H:X) + (M) AND #opr8i IMM A4 ii 2 pp AND opr8a DIR B4 dd 3 rpp AND opr16a EXT C4 hh ll 4 prpp AND oprx16,X Logical AND IX2 D4 ee ff 4 prpp 0 – – (cid:166) (cid:166) – AND oprx8,X A ← (A) & (M) IX1 E4 ff 3 rpp AND ,X IX F4 3 rfp AND oprx16,SP SP2 9E D4 ee ff 5 pprpp AND oprx8,SP SP1 9E E4 ff 4 prpp ASL opr8a Arithmetic Shift Left DIR 38 dd 5 rfwpp ASLA INH 48 1 p ASLX INH 58 1 p C 0 (cid:166) – – (cid:166) (cid:166) (cid:166) ASL oprx8,X IX1 68 ff 5 rfwpp b7 b0 ASL ,X IX 78 4 rfwp ASL oprx8,SP (Same as LSL) SP1 9E 68 ff 6 prfwpp ASR opr8a DIR 37 dd 5 rfwpp ASRA Arithmetic Shift Right INH 47 1 p ASRX INH 57 1 p (cid:166) – – (cid:166) (cid:166) (cid:166) ASR oprx8,X C IX1 67 ff 5 rfwpp ASR ,X b7 b0 IX 77 4 rfwp ASR oprx8,SP SP1 9E 67 ff 6 prfwpp Branch if Carry Bit Clear BCC rel REL 24 rr 3 ppp – – – – – – (if C = 0) MC9S08JM60 Series Data Sheet, Rev. 5 108 Freescale Semiconductor

Chapter7 Central Processor Unit (S08CPUV2) Table7-2. . Instruction Set Summary (Sheet 2 of 9) s Affect SFoourrmce Operation AddresMode Object Code Cycles CyDc-ebtayi-lCsyc VHonI CNC ZR C DIR (b0) 11 dd 5 rfwpp DIR (b1) 13 dd 5 rfwpp DIR (b2) 15 dd 5 rfwpp Clear Bit n in Memory DIR (b3) 17 dd 5 rfwpp BCLR n,opr8a – – – – – – (Mn ← 0) DIR (b4) 19 dd 5 rfwpp DIR (b5) 1B dd 5 rfwpp DIR (b6) 1D dd 5 rfwpp DIR (b7) 1F dd 5 rfwpp Branch if Carry Bit Set (if C = 1) BCS rel REL 25 rr 3 ppp – – – – – – (Same as BLO) BEQ rel Branch if Equal (if Z = 1) REL 27 rr 3 ppp – – – – – – Branch if Greater Than or Equal To BGE rel REL 90 rr 3 ppp – – – – – – (if N ⊕ V = 0) (Signed) Enter active background if ENBDM=1 BGND Waits for and processes BDM commands INH 82 5+ fp...ppp – – – – – – until GO, TRACE1, or TAGGO Branch if Greater Than (if Z | (N ⊕ V) = 0) BGT rel REL 92 rr 3 ppp – – – – – – (Signed) BHCC rel Branch if Half Carry Bit Clear (if H = 0) REL 28 rr 3 ppp – – – – – – BHCS rel Branch if Half Carry Bit Set (if H = 1) REL 29 rr 3 ppp – – – – – – BHI rel Branch if Higher (if C | Z = 0) REL 22 rr 3 ppp – – – – – – Branch if Higher or Same (if C = 0) BHS rel REL 24 rr 3 ppp – – – – – – (Same as BCC) BIH rel Branch if IRQ Pin High (if IRQ pin = 1) REL 2F rr 3 ppp – – – – – – BIL rel Branch if IRQ Pin Low (if IRQ pin = 0) REL 2E rr 3 ppp – – – – – – BIT #opr8i IMM A5 ii 2 pp BIT opr8a DIR B5 dd 3 rpp BIT opr16a EXT C5 hh ll 4 prpp Bit Test BIT oprx16,X IX2 D5 ee ff 4 prpp (A) & (M) 0 – – (cid:166) (cid:166) – BIT oprx8,X IX1 E5 ff 3 rpp (CCR Updated but Operands Not Changed) BIT ,X IX F5 3 rfp BIT oprx16,SP SP2 9E D5 ee ff 5 pprpp BIT oprx8,SP SP1 9E E5 ff 4 prpp Branch if Less Than or Equal To BLE rel REL 93 rr 3 ppp – – – – – – (if Z | (N ⊕ V) = 1) (Signed) BLO rel Branch if Lower (if C = 1) (Same as BCS) REL 25 rr 3 ppp – – – – – – BLS rel Branch if Lower or Same (if C | Z = 1) REL 23 rr 3 ppp – – – – – – BLT rel Branch if Less Than (if N ⊕ V = 1) (Signed) REL 91 rr 3 ppp – – – – – – BMC rel Branch if Interrupt Mask Clear (if I = 0) REL 2C rr 3 ppp – – – – – – BMI rel Branch if Minus (if N = 1) REL 2B rr 3 ppp – – – – – – BMS rel Branch if Interrupt Mask Set (if I = 1) REL 2D rr 3 ppp – – – – – – BNE rel Branch if Not Equal (if Z = 0) REL 26 rr 3 ppp – – – – – – BPL rel Branch if Plus (if N = 0) REL 2A rr 3 ppp – – – – – – MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 109

Chapter7 Central Processor Unit (S08CPUV2) Table7-2. . Instruction Set Summary (Sheet 3 of 9) s Affect SFoourrmce Operation AddresMode Object Code Cycles CyDc-ebtayi-lCsyc VHonI CNC ZR C BRA rel Branch Always (if I = 1) REL 20 rr 3 ppp – – – – – – DIR (b0) 01 dd rr 5 rpppp DIR (b1) 03 dd rr 5 rpppp DIR (b2) 05 dd rr 5 rpppp DIR (b3) 07 dd rr 5 rpppp BRCLR n,opr8a,rel Branch if Bit n in Memory Clear (if (Mn) = 0) – – – – – (cid:166) DIR (b4) 09 dd rr 5 rpppp DIR (b5) 0B dd rr 5 rpppp DIR (b6) 0D dd rr 5 rpppp DIR (b7) 0F dd rr 5 rpppp BRN rel Branch Never (if I = 0) REL 21 rr 3 ppp – – – – – – DIR (b0) 00 dd rr 5 rpppp DIR (b1) 02 dd rr 5 rpppp DIR (b2) 04 dd rr 5 rpppp DIR (b3) 06 dd rr 5 rpppp BRSET n,opr8a,rel Branch if Bit n in Memory Set (if (Mn) = 1) – – – – – (cid:166) DIR (b4) 08 dd rr 5 rpppp DIR (b5) 0A dd rr 5 rpppp DIR (b6) 0C dd rr 5 rpppp DIR (b7) 0E dd rr 5 rpppp DIR (b0) 10 dd 5 rfwpp DIR (b1) 12 dd 5 rfwpp DIR (b2) 14 dd 5 rfwpp DIR (b3) 16 dd 5 rfwpp BSET n,opr8a Set Bit n in Memory (Mn ← 1) – – – – – – DIR (b4) 18 dd 5 rfwpp DIR (b5) 1A dd 5 rfwpp DIR (b6) 1C dd 5 rfwpp DIR (b7) 1E dd 5 rfwpp Branch to Subroutine PC ← (PC) + $0002 BSR rel push (PCL); SP ← (SP) – $0001 REL AD rr 5 ssppp – – – – – – push (PCH); SP ← (SP) – $0001 PC ← (PC) + rel CBEQ opr8a,rel Compare and... Branch if (A) = (M) DIR 31 dd rr 5 rpppp CBEQA #opr8i,rel Branch if (A) = (M) IMM 41 ii rr 4 pppp CBEQX #opr8i,rel Branch if (X) = (M) IMM 51 ii rr 4 pppp – – – – – – CBEQ oprx8,X+,rel Branch if (A) = (M) IX1+ 61 ff rr 5 rpppp CBEQ ,X+,rel Branch if (A) = (M) IX+ 71 rr 5 rfppp CBEQ oprx8,SP,rel Branch if (A) = (M) SP1 9E 61 ff rr 6 prpppp CLC Clear Carry Bit (C ← 0) INH 98 1 p – – – – – 0 CLI Clear Interrupt Mask Bit (I ← 0) INH 9A 1 p – – 0 – – – CLR opr8a Clear M ← $00 DIR 3F dd 5 rfwpp CLRA A ← $00 INH 4F 1 p CLRX X ← $00 INH 5F 1 p CLRH H ← $00 INH 8C 1 p 0 – – 0 1 – CLR oprx8,X M ← $00 IX1 6F ff 5 rfwpp CLR ,X M ← $00 IX 7F 4 rfwp CLR oprx8,SP M ← $00 SP1 9E 6F ff 6 prfwpp MC9S08JM60 Series Data Sheet, Rev. 5 110 Freescale Semiconductor

Chapter7 Central Processor Unit (S08CPUV2) Table7-2. . Instruction Set Summary (Sheet 4 of 9) s Affect SFoourrmce Operation AddresMode Object Code Cycles CyDc-ebtayi-lCsyc VHonI CNC ZR C CMP #opr8i IMM A1 ii 2 pp CMP opr8a DIR B1 dd 3 rpp CMP opr16a EXT C1 hh ll 4 prpp Compare Accumulator with Memory CMP oprx16,X IX2 D1 ee ff 4 prpp A – M (cid:166) – – (cid:166) (cid:166) (cid:166) CMP oprx8,X IX1 E1 ff 3 rpp (CCR Updated But Operands Not Changed) CMP ,X IX F1 3 rfp CMP oprx16,SP SP2 9E D1 ee ff 5 pprpp CMP oprx8,SP SP1 9E E1 ff 4 prpp COM opr8a Complement M ← (M)= $FF – (M) DIR 33 dd 5 rfwpp COMA (One’s Complement) A ← (A) = $FF – (A) INH 43 1 p COMX X ← (X) = $FF – (X) INH 53 1 p 0 – – (cid:166) (cid:166) 1 COM oprx8,X M ← (M) = $FF – (M) IX1 63 ff 5 rfwpp COM ,X M ← (M) = $FF – (M) IX 73 4 rfwp COM oprx8,SP M ← (M) = $FF – (M) SP1 9E 63 ff 6 prfwpp CPHX opr16a EXT 3E hh ll 6 prrfpp Compare Index Register (H:X) with Memory CPHX #opr16i IMM 65 jj kk 3 ppp (H:X) – (M:M + $0001) (cid:166) – – (cid:166) (cid:166) (cid:166) CPHX opr8a DIR 75 dd 5 rrfpp (CCR Updated But Operands Not Changed) CPHX oprx8,SP SP1 9E F3 ff 6 prrfpp CPX #opr8i IMM A3 ii 2 pp CPX opr8a DIR B3 dd 3 rpp CPX opr16a Compare X (Index Register Low) with EXT C3 hh ll 4 prpp CPX oprx16,X Memory IX2 D3 ee ff 4 prpp (cid:166) – – (cid:166) (cid:166) (cid:166) CPX oprx8,X X – M IX1 E3 ff 3 rpp CPX ,X (CCR Updated But Operands Not Changed) IX F3 3 rfp CPX oprx16,SP SP2 9E D3 ee ff 5 pprpp CPX oprx8,SP SP1 9E E3 ff 4 prpp Decimal Adjust Accumulator DAA INH 72 1 p U – – (cid:166) (cid:166) (cid:166) After ADD or ADC of BCD Values DBNZ opr8a,rel DIR 3B dd rr 7 rfwpppp DBNZA rel INH 4B rr 4 fppp Decrement A, X, or M and Branch if Not Zero DBNZX rel INH 5B rr 4 fppp (if (result) ≠ 0) – – – – – – DBNZ oprx8,X,rel IX1 6B ff rr 7 rfwpppp DBNZX Affects X Not H DBNZ ,X,rel IX 7B rr 6 rfwppp DBNZ oprx8,SP,rel SP1 9E 6B ff rr 8 prfwpppp DEC opr8a Decrement M ← (M) – $01 DIR 3A dd 5 rfwpp DECA A ← (A) – $01 INH 4A 1 p DECX X ← (X) – $01 INH 5A 1 p (cid:166) – – (cid:166) (cid:166) – DEC oprx8,X M ← (M) – $01 IX1 6A ff 5 rfwpp DEC ,X M ← (M) – $01 IX 7A 4 rfwp DEC oprx8,SP M ← (M) – $01 SP1 9E 6A ff 6 prfwpp Divide DIV INH 52 6 fffffp – – – – (cid:166) (cid:166) A ← (H:A)÷(X); H ← Remainder EOR #opr8i Exclusive OR Memory with Accumulator IMM A8 ii 2 pp EOR opr8a A ← (A ⊕ M) DIR B8 dd 3 rpp EOR opr16a EXT C8 hh ll 4 prpp EOR oprx16,X IX2 D8 ee ff 4 prpp 0 – – (cid:166) (cid:166) – EOR oprx8,X IX1 E8 ff 3 rpp EOR ,X IX F8 3 rfp EOR oprx16,SP SP2 9E D8 ee ff 5 pprpp EOR oprx8,SP SP1 9E E8 ff 4 prpp MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 111

Chapter7 Central Processor Unit (S08CPUV2) Table7-2. . Instruction Set Summary (Sheet 5 of 9) s Affect SFoourrmce Operation AddresMode Object Code Cycles CyDc-ebtayi-lCsyc VHonI CNC ZR C INC opr8a Increment M ← (M) + $01 DIR 3C dd 5 rfwpp INCA A ← (A) + $01 INH 4C 1 p INCX X ← (X) + $01 INH 5C 1 p (cid:166) – – (cid:166) (cid:166) – INC oprx8,X M ← (M) + $01 IX1 6C ff 5 rfwpp INC ,X M ← (M) + $01 IX 7C 4 rfwp INC oprx8,SP M ← (M) + $01 SP1 9E 6C ff 6 prfwpp JMP opr8a DIR BC dd 3 ppp JMP opr16a EXT CC hh ll 4 pppp Jump JMP oprx16,X IX2 DC ee ff 4 pppp – – – – – – PC ← Jump Address JMP oprx8,X IX1 EC ff 3 ppp JMP ,X IX FC 3 ppp JSR opr8a Jump to Subroutine DIR BD dd 5 ssppp JSR opr16a PC ← (PC) + n (n = 1, 2, or 3) EXT CD hh ll 6 pssppp JSR oprx16,X Push (PCL); SP ← (SP) – $0001 IX2 DD ee ff 6 pssppp – – – – – – JSR oprx8,X Push (PCH); SP ← (SP) – $0001 IX1 ED ff 5 ssppp JSR ,X PC ← Unconditional Address IX FD 5 ssppp LDA #opr8i IMM A6 ii 2 pp LDA opr8a DIR B6 dd 3 rpp LDA opr16a EXT C6 hh ll 4 prpp LDA oprx16,X Load Accumulator from Memory IX2 D6 ee ff 4 prpp 0 – – (cid:166) (cid:166) – LDA oprx8,X A ← (M) IX1 E6 ff 3 rpp LDA ,X IX F6 3 rfp LDA oprx16,SP SP2 9E D6 ee ff 5 pprpp LDA oprx8,SP SP1 9E E6 ff 4 prpp LDHX #opr16i IMM 45 jj kk 3 ppp LDHX opr8a DIR 55 dd 4 rrpp LDHX opr16a EXT 32 hh ll 5 prrpp Load Index Register (H:X) LDHX ,X IX 9E AE 5 prrfp 0 – – (cid:166) (cid:166) – H:X ← (M:M + $0001) LDHX oprx16,X IX2 9E BE ee ff 6 pprrpp LDHX oprx8,X IX1 9E CE ff 5 prrpp LDHX oprx8,SP SP1 9E FE ff 5 prrpp LDX #opr8i IMM AE ii 2 pp LDX opr8a DIR BE dd 3 rpp LDX opr16a EXT CE hh ll 4 prpp LDX oprx16,X Load X (Index Register Low) from Memory IX2 DE ee ff 4 prpp 0 – – (cid:166) (cid:166) – LDX oprx8,X X ← (M) IX1 EE ff 3 rpp LDX ,X IX FE 3 rfp LDX oprx16,SP SP2 9E DE ee ff 5 pprpp LDX oprx8,SP SP1 9E EE ff 4 prpp LSL opr8a Logical Shift Left DIR 38 dd 5 rfwpp LSLA INH 48 1 p LSLX C 0 INH 58 1 p (cid:166) – – (cid:166) (cid:166) (cid:166) LSL oprx8,X IX1 68 ff 5 rfwpp b7 b0 LSL ,X IX 78 4 rfwp LSL oprx8,SP (Same as ASL) SP1 9E 68 ff 6 prfwpp LSR opr8a DIR 34 dd 5 rfwpp Logical Shift Right LSRA INH 44 1 p LSRX INH 54 1 p (cid:166) – – 0 (cid:166) (cid:166) LSR oprx8,X 0 C IX1 64 ff 5 rfwpp LSR ,X b7 b0 IX 74 4 rfwp LSR oprx8,SP SP1 9E 64 ff 6 prfwpp MC9S08JM60 Series Data Sheet, Rev. 5 112 Freescale Semiconductor

Chapter7 Central Processor Unit (S08CPUV2) Table7-2. . Instruction Set Summary (Sheet 6 of 9) s Affect SFoourrmce Operation AddresMode Object Code Cycles CyDc-ebtayi-lCsyc VHonI CNC ZR C MOV opr8a,opr8a Move DIR/DIR 4E dd dd 5 rpwpp MOV opr8a,X+ (M) ← (M) DIR/IX+ 5E dd 5 rfwpp destination source 0 – – (cid:166) (cid:166) – MOV #opr8i,opr8a In IX+/DIR and DIR/IX+ Modes, IMM/DIR 6E ii dd 4 pwpp MOV ,X+,opr8a H:X ← (H:X) + $0001 IX+/DIR 7E dd 5 rfwpp Unsigned multiply MUL INH 42 5 ffffp – 0 – – – 0 X:A ← (X) × (A) NEG opr8a Negate M ← – (M) = $00 – (M) DIR 30 dd 5 rfwpp NEGA (Two’s Complement) A ← – (A) = $00 – (A) INH 40 1 p NEGX X ← – (X) = $00 – (X) INH 50 1 p (cid:166) – – (cid:166) (cid:166) (cid:166) NEG oprx8,X M ← – (M) = $00 – (M) IX1 60 ff 5 rfwpp NEG ,X M ← – (M) = $00 – (M) IX 70 4 rfwp NEG oprx8,SP M ← – (M) = $00 – (M) SP1 9E 60 ff 6 prfwpp NOP No Operation — Uses 1 Bus Cycle INH 9D 1 p – – – – – – Nibble Swap Accumulator NSA INH 62 1 p – – – – – – A ← (A[3:0]:A[7:4]) ORA #opr8i IMM AA ii 2 pp ORA opr8a DIR BA dd 3 rpp ORA opr16a EXT CA hh ll 4 prpp ORA oprx16,X Inclusive OR Accumulator and Memory IX2 DA ee ff 4 prpp 0 – – (cid:166) (cid:166) – ORA oprx8,X A ← (A) | (M) IX1 EA ff 3 rpp ORA ,X IX FA 3 rfp ORA oprx16,SP SP2 9E DA ee ff 5 pprpp ORA oprx8,SP SP1 9E EA ff 4 prpp Push Accumulator onto Stack PSHA INH 87 2 sp – – – – – – Push (A); SP ← (SP) – $0001 Push H (Index Register High) onto Stack PSHH INH 8B 2 sp – – – – – – Push (H); SP ← (SP) – $0001 Push X (Index Register Low) onto Stack PSHX INH 89 2 sp – – – – – – Push (X); SP ← (SP) – $0001 Pull Accumulator from Stack PULA INH 86 3 ufp – – – – – – SP ← (SP + $0001); Pull (A) Pull H (Index Register High) from Stack PULH INH 8A 3 ufp – – – – – – SP ← (SP + $0001); Pull (H) Pull X (Index Register Low) from Stack PULX INH 88 3 ufp – – – – – – SP ← (SP + $0001); Pull (X) ROL opr8a Rotate Left through Carry DIR 39 dd 5 rfwpp ROLA INH 49 1 p ROLX INH 59 1 p (cid:166) – – (cid:166) (cid:166) (cid:166) ROL oprx8,X C IX1 69 ff 5 rfwpp ROL ,X b7 b0 IX 79 4 rfwp ROL oprx8,SP SP1 9E 69 ff 6 prfwpp ROR opr8a Rotate Right through Carry DIR 36 dd 5 rfwpp RORA INH 46 1 p RORX INH 56 1 p ROR oprx8,X C IX1 66 ff 5 rfwpp (cid:166) – – (cid:166) (cid:166) (cid:166) ROR ,X b7 b0 IX 76 4 rfwp ROR oprx8,SP SP1 9E 66 ff 6 prfwpp MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 113

Chapter7 Central Processor Unit (S08CPUV2) Table7-2. . Instruction Set Summary (Sheet 7 of 9) s Affect SFoourrmce Operation AddresMode Object Code Cycles CyDc-ebtayi-lCsyc VHonI CNC ZR C Reset Stack Pointer (Low Byte) RSP SPL ← $FF INH 9C 1 p – – – – – – (High Byte Not Affected) Return from Interrupt SP ← (SP) + $0001; Pull (CCR) SP ← (SP) + $0001; Pull (A) RTI INH 80 9 uuuuufppp (cid:166) (cid:166) (cid:166) (cid:166) (cid:166) (cid:166) SP ← (SP) + $0001; Pull (X) SP ← (SP) + $0001; Pull (PCH) SP ← (SP) + $0001; Pull (PCL) Return from Subroutine RTS SP ← SP + $0001; Pull (PCH) INH 81 5 ufppp – – – – – – SP ← SP + $0001; Pull (PCL) SBC #opr8i IMM A2 ii 2 pp SBC opr8a DIR B2 dd 3 rpp SBC opr16a EXT C2 hh ll 4 prpp SBC oprx16,X Subtract with Carry IX2 D2 ee ff 4 prpp (cid:166) – – (cid:166) (cid:166) (cid:166) SBC oprx8,X A ← (A) – (M) – (C) IX1 E2 ff 3 rpp SBC ,X IX F2 3 rfp SBC oprx16,SP SP2 9E D2 ee ff 5 pprpp SBC oprx8,SP SP1 9E E2 ff 4 prpp Set Carry Bit SEC INH 99 1 p – – – – – 1 (C ← 1) Set Interrupt Mask Bit SEI INH 9B 1 p – – 1 – – – (I ← 1) STA opr8a DIR B7 dd 3 wpp STA opr16a EXT C7 hh ll 4 pwpp STA oprx16,X IX2 D7 ee ff 4 pwpp Store Accumulator in Memory STA oprx8,X IX1 E7 ff 3 wpp 0 – – (cid:166) (cid:166) – M ← (A) STA ,X IX F7 2 wp STA oprx16,SP SP2 9E D7 ee ff 5 ppwpp STA oprx8,SP SP1 9E E7 ff 4 pwpp STHX opr8a DIR 35 dd 4 wwpp Store H:X (Index Reg.) STHX opr16a EXT 96 hh ll 5 pwwpp 0 – – (cid:166) (cid:166) – (M:M + $0001) ← (H:X) STHX oprx8,SP SP1 9E FF ff 5 pwwpp Enable Interrupts: Stop Processing STOP Refer to MCU Documentation INH 8E 2 fp... – – 0 – – – I bit ← 0; Stop Processing STX opr8a DIR BF dd 3 wpp STX opr16a EXT CF hh ll 4 pwpp STX oprx16,X Store X (Low 8 Bits of Index Register) IX2 DF ee ff 4 pwpp STX oprx8,X in Memory IX1 EF ff 3 wpp 0 – – (cid:166) (cid:166) – STX ,X M ← (X) IX FF 2 wp STX oprx16,SP SP2 9E DF ee ff 5 ppwpp STX oprx8,SP SP1 9E EF ff 4 pwpp MC9S08JM60 Series Data Sheet, Rev. 5 114 Freescale Semiconductor

Chapter7 Central Processor Unit (S08CPUV2) Table7-2. . Instruction Set Summary (Sheet 8 of 9) s Affect SFoourrmce Operation AddresMode Object Code Cycles CyDc-ebtayi-lCsyc VHonI CNC ZR C SUB #opr8i IMM A0 ii 2 pp SUB opr8a DIR B0 dd 3 rpp SUB opr16a EXT C0 hh ll 4 prpp SUB oprx16,X Subtract IX2 D0 ee ff 4 prpp (cid:166) – – (cid:166) (cid:166) (cid:166) SUB oprx8,X A ← (A) – (M) IX1 E0 ff 3 rpp SUB ,X IX F0 3 rfp SUB oprx16,SP SP2 9E D0 ee ff 5 pprpp SUB oprx8,SP SP1 9E E0 ff 4 prpp Software Interrupt PC ← (PC) + $0001 Push (PCL); SP ← (SP) – $0001 Push (PCH); SP ← (SP) – $0001 Push (X); SP ← (SP) – $0001 SWI INH 83 11 sssssvvfppp – – 1 – – – Push (A); SP ← (SP) – $0001 Push (CCR); SP ← (SP) – $0001 I ← 1; PCH ← Interrupt Vector High Byte PCL ← Interrupt Vector Low Byte Transfer Accumulator to CCR TAP INH 84 1 p (cid:166) (cid:166) (cid:166) (cid:166) (cid:166) (cid:166) CCR ← (A) Transfer Accumulator to X (Index Register TAX Low) INH 97 1 p – – – – – – X ← (A) Transfer CCR to Accumulator TPA INH 85 1 p – – – – – – A ← (CCR) TST opr8a Test for Negative or Zero (M) – $00 DIR 3D dd 4 rfpp TSTA (A) – $00 INH 4D 1 p TSTX (X) – $00 INH 5D 1 p 0 – – (cid:166) (cid:166) – TST oprx8,X (M) – $00 IX1 6D ff 4 rfpp TST ,X (M) – $00 IX 7D 3 rfp TST oprx8,SP (M) – $00 SP1 9E 6D ff 5 prfpp Transfer SP to Index Reg. TSX INH 95 2 fp – – – – – – H:X ← (SP) + $0001 Transfer X (Index Reg. Low) to Accumulator TXA INH 9F 1 p – – – – – – A ← (X) MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 115

Chapter7 Central Processor Unit (S08CPUV2) Table7-2. . Instruction Set Summary (Sheet 9 of 9) s Affect SFoourrmce Operation AddresMode Object Code Cycles CyDc-ebtayi-lCsyc VHonI CNC ZR C Transfer Index Reg. to SP TXS INH 94 2 fp – – – – – – SP ← (H:X) – $0001 Enable Interrupts; Wait for Interrupt WAIT INH 8F 2+ fp... – – 0 – – – I bit ← 0; Halt CPU Source Form: Everything in the source forms columns, except expressions in italic characters, is literal information which must appear in the assembly source file exactly as shown. The initial 3- to 5-letter mnemonic and the characters (# , ( ) and +) are always a literal characters. n Any label or expression that evaluates to a single integer in the range 0-7. opr8i Any label or expression that evaluates to an 8-bit immediate value. opr16i Any label or expression that evaluates to a 16-bit immediate value. opr8a Any label or expression that evaluates to an 8-bit direct-page address ($00xx). opr16a Any label or expression that evaluates to a 16-bit address. oprx8 Any label or expression that evaluates to an unsigned 8-bit value, used for indexed addressing. oprx16 Any label or expression that evaluates to a 16-bit value, used for indexed addressing. rel Any label or expression that refers to an address that is within –128 to +127 locations from the start of the next instruction. Operation Symbols: Addressing Modes: A Accumulator DIR Direct addressing mode CCR Condition code register EXT Extended addressing mode H Index register high byte IMM Immediate addressing mode M Memory location INH Inherent addressing mode n Any bit IX Indexed, no offset addressing mode opr Operand (one or two bytes) IX1 Indexed, 8-bit offset addressing mode PC Program counter IX2 Indexed, 16-bit offset addressing mode PCH Program counter high byte IX+ Indexed, no offset, post increment addressing mode PCL Program counter low byte IX1+ Indexed, 8-bit offset, post increment addressing mode rel Relative program counter offset byte REL Relative addressing mode SP Stack pointer SP1 Stack pointer, 8-bit offset addressing mode SPL Stack pointer low byte SP2 Stack pointer 16-bit offset addressing mode X Index register low byte Cycle-by-Cycle Codes: & Logical AND f Free cycle. This indicates a cycle where the CPU | Logical OR ⊕ Logical EXCLUSIVE OR does not require use of the system buses. An f cycle is always one cycle of the system bus clock ( ) Contents of and is always a read cycle. + Add p Progryam fetch; read from next consecutive – Subtract, Negation (two’s complement) location in program memory × Multiply r Read 8-bit operand ÷ Divide s Push (write) one byte onto stack # Immediate value u Pop (read) one byte from stack ← Loaded with v Read vector from $FFxx (high byte first) : Concatenated with w Write 8-bit operand CCR Bits: CCR Effects: V Overflow bit (cid:166) Set or cleared H Half-carry bit – Not affected I Interrupt mask U Undefined N Negative bit Z Zero bit C Carry/borrow bit MC9S08JM60 Series Data Sheet, Rev. 5 116 Freescale Semiconductor

Chapter7 Central Processor Unit (S08CPUV2) Table7-3. Opcode Map (Sheet 1 of 2) Bit-Manipulation Branch Read-Modify-Write Control Register/Memory 00 5 10 5 20 3 30 5 40 1 50 1 60 5 70 4 80 9 90 3 A0 2 B0 3 C0 4 D0 4 E0 3 F0 3 BRSET0 BSET0 BRA NEG NEGA NEGX NEG NEG RTI BGE SUB SUB SUB SUB SUB SUB 3 DIR 2 DIR 2 REL 2 DIR 1 INH 1 INH 2 IX1 1 IX 1 INH 2 REL 2 IMM 2 DIR 3 EXT 3 IX2 2 IX1 1 IX 01 5 11 5 21 3 31 5 41 4 51 4 61 5 71 5 81 6 91 3 A1 2 B1 3 C1 4 D1 4 E1 3 F1 3 BRCLR0 BCLR0 BRN CBEQ CBEQA CBEQX CBEQ CBEQ RTS BLT CMP CMP CMP CMP CMP CMP 3 DIR 2 DIR 2 REL 3 DIR 3 IMM 3 IMM 3 IX1+ 2 IX+ 1 INH 2 REL 2 IMM 2 DIR 3 EXT 3 IX2 2 IX1 1 IX 02 5 12 5 22 3 32 5 42 5 52 6 62 1 72 1 82 5+ 92 3 A2 2 B2 3 C2 4 D2 4 E2 3 F2 3 BRSET1 BSET1 BHI LDHX MUL DIV NSA DAA BGND BGT SBC SBC SBC SBC SBC SBC 3 DIR 2 DIR 2 REL 3 EXT 1 INH 1 INH 1 INH 1 INH 1 INH 2 REL 2 IMM 2 DIR 3 EXT 3 IX2 2 IX1 1 IX 03 5 13 5 23 3 33 5 43 1 53 1 63 5 73 4 83 11 93 3 A3 2 B3 3 C3 4 D3 4 E3 3 F3 3 BRCLR1 BCLR1 BLS COM COMA COMX COM COM SWI BLE CPX CPX CPX CPX CPX CPX 3 DIR 2 DIR 2 REL 2 DIR 1 INH 1 INH 2 IX1 1 IX 1 INH 2 REL 2 IMM 2 DIR 3 EXT 3 IX2 2 IX1 1 IX 04 5 14 5 24 3 34 5 44 1 54 1 64 5 74 4 84 1 94 2 A4 2 B4 3 C4 4 D4 4 E4 3 F4 3 BRSET2 BSET2 BCC LSR LSRA LSRX LSR LSR TAP TXS AND AND AND AND AND AND 3 DIR 2 DIR 2 REL 2 DIR 1 INH 1 INH 2 IX1 1 IX 1 INH 1 INH 2 IMM 2 DIR 3 EXT 3 IX2 2 IX1 1 IX 05 5 15 5 25 3 35 4 45 3 55 4 65 3 75 5 85 1 95 2 A5 2 B5 3 C5 4 D5 4 E5 3 F5 3 BRCLR2 BCLR2 BCS STHX LDHX LDHX CPHX CPHX TPA TSX BIT BIT BIT BIT BIT BIT 3 DIR 2 DIR 2 REL 2 DIR 3 IMM 2 DIR 3 IMM 2 DIR 1 INH 1 INH 2 IMM 2 DIR 3 EXT 3 IX2 2 IX1 1 IX 06 5 16 5 26 3 36 5 46 1 56 1 66 5 76 4 86 3 96 5 A6 2 B6 3 C6 4 D6 4 E6 3 F6 3 BRSET3 BSET3 BNE ROR RORA RORX ROR ROR PULA STHX LDA LDA LDA LDA LDA LDA 3 DIR 2 DIR 2 REL 2 DIR 1 INH 1 INH 2 IX1 1 IX 1 INH 3 EXT 2 IMM 2 DIR 3 EXT 3 IX2 2 IX1 1 IX 07 5 17 5 27 3 37 5 47 1 57 1 67 5 77 4 87 2 97 1 A7 2 B7 3 C7 4 D7 4 E7 3 F7 2 BRCLR3 BCLR3 BEQ ASR ASRA ASRX ASR ASR PSHA TAX AIS STA STA STA STA STA 3 DIR 2 DIR 2 REL 2 DIR 1 INH 1 INH 2 IX1 1 IX 1 INH 1 INH 2 IMM 2 DIR 3 EXT 3 IX2 2 IX1 1 IX 08 5 18 5 28 3 38 5 48 1 58 1 68 5 78 4 88 3 98 1 A8 2 B8 3 C8 4 D8 4 E8 3 F8 3 BRSET4 BSET4 BHCC LSL LSLA LSLX LSL LSL PULX CLC EOR EOR EOR EOR EOR EOR 3 DIR 2 DIR 2 REL 2 DIR 1 INH 1 INH 2 IX1 1 IX 1 INH 1 INH 2 IMM 2 DIR 3 EXT 3 IX2 2 IX1 1 IX 09 5 19 5 29 3 39 5 49 1 59 1 69 5 79 4 89 2 99 1 A9 2 B9 3 C9 4 D9 4 E9 3 F9 3 BRCLR4 BCLR4 BHCS ROL ROLA ROLX ROL ROL PSHX SEC ADC ADC ADC ADC ADC ADC 3 DIR 2 DIR 2 REL 2 DIR 1 INH 1 INH 2 IX1 1 IX 1 INH 1 INH 2 IMM 2 DIR 3 EXT 3 IX2 2 IX1 1 IX 0A 5 1A 5 2A 3 3A 5 4A 1 5A 1 6A 5 7A 4 8A 3 9A 1 AA 2 BA 3 CA 4 DA 4 EA 3 FA 3 BRSET5 BSET5 BPL DEC DECA DECX DEC DEC PULH CLI ORA ORA ORA ORA ORA ORA 3 DIR 2 DIR 2 REL 2 DIR 1 INH 1 INH 2 IX1 1 IX 1 INH 1 INH 2 IMM 2 DIR 3 EXT 3 IX2 2 IX1 1 IX 0B 5 1B 5 2B 3 3B 7 4B 4 5B 4 6B 7 7B 6 8B 2 9B 1 AB 2 BB 3 CB 4 DB 4 EB 3 FB 3 BRCLR5 BCLR5 BMI DBNZ DBNZA DBNZX DBNZ DBNZ PSHH SEI ADD ADD ADD ADD ADD ADD 3 DIR 2 DIR 2 REL 3 DIR 2 INH 2 INH 3 IX1 2 IX 1 INH 1 INH 2 IMM 2 DIR 3 EXT 3 IX2 2 IX1 1 IX 0C 5 1C 5 2C 3 3C 5 4C 1 5C 1 6C 5 7C 4 8C 1 9C 1 BC 3 CC 4 DC 4 EC 3 FC 3 BRSET6 BSET6 BMC INC INCA INCX INC INC CLRH RSP JMP JMP JMP JMP JMP 3 DIR 2 DIR 2 REL 2 DIR 1 INH 1 INH 2 IX1 1 IX 1 INH 1 INH 2 DIR 3 EXT 3 IX2 2 IX1 1 IX 0D 5 1D 5 2D 3 3D 4 4D 1 5D 1 6D 4 7D 3 9D 1 AD 5 BD 5 CD 6 DD 6 ED 5 FD 5 BRCLR6 BCLR6 BMS TST TSTA TSTX TST TST NOP BSR JSR JSR JSR JSR JSR 3 DIR 2 DIR 2 REL 2 DIR 1 INH 1 INH 2 IX1 1 IX 1 INH 2 REL 2 DIR 3 EXT 3 IX2 2 IX1 1 IX 0E 5 1E 5 2E 3 3E 6 4E 5 5E 5 6E 4 7E 5 8E 2+ 9E AE 2 BE 3 CE 4 DE 4 EE 3 FE 3 BRSET7 BSET7 BIL CPHX MOV MOV MOV MOV STOP Page 2 LDX LDX LDX LDX LDX LDX 3 DIR 2 DIR 2 REL 3 EXT 3 DD 2 DIX+ 3 IMD 2 IX+D 1 INH 2 IMM 2 DIR 3 EXT 3 IX2 2 IX1 1 IX 0F 5 1F 5 2F 3 3F 5 4F 1 5F 1 6F 5 7F 4 8F 2+ 9F 1 AF 2 BF 3 CF 4 DF 4 EF 3 FF 2 BRCLR7 BCLR7 BIH CLR CLRA CLRX CLR CLR WAIT TXA AIX STX STX STX STX STX 3 DIR 2 DIR 2 REL 2 DIR 1 INH 1 INH 2 IX1 1 IX 1 INH 1 INH 2 IMM 2 DIR 3 EXT 3 IX2 2 IX1 1 IX INH Inherent REL Relative SP1 Stack Pointer, 8-Bit Offset IMM Immediate IX Indexed, No Offset SP2 Stack Pointer, 16-Bit Offset DIR Direct IX1 Indexed, 8-Bit Offset IX+ Indexed, No Offset with EXT Extended IX2 Indexed, 16-Bit Offset Post Increment DD DIR to DIR IMD IMM to DIR IX1+ Indexed, 1-Byte Offset with IX+D IX+ to DIR DIX+ DIR to IX+ Post Increment Opcode in Hexadecimal F0 3 HCS08 Cycles SUB Instruction Mnemonic Number of Bytes 1 IX Addressing Mode MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 117

Chapter7 Central Processor Unit (S08CPUV2) Table7-3. Opcode Map (Sheet 2 of 2) Bit-Manipulation Branch Read-Modify-Write Control Register/Memory 9E60 6 9ED0 5 9EE0 4 NEG SUB SUB 3 SP1 4 SP2 3 SP1 9E61 6 9ED1 5 9EE1 4 CBEQ CMP CMP 4 SP1 4 SP2 3 SP1 9ED2 5 9EE2 4 SBC SBC 4 SP2 3 SP1 9E63 6 9ED3 5 9EE3 4 9EF3 6 COM CPX CPX CPHX 3 SP1 4 SP2 3 SP1 3 SP1 9E64 6 9ED4 5 9EE4 4 LSR AND AND 3 SP1 4 SP2 3 SP1 9ED5 5 9EE5 4 BIT BIT 4 SP2 3 SP1 9E66 6 9ED6 5 9EE6 4 ROR LDA LDA 3 SP1 4 SP2 3 SP1 9E67 6 9ED7 5 9EE7 4 ASR STA STA 3 SP1 4 SP2 3 SP1 9E68 6 9ED8 5 9EE8 4 LSL EOR EOR 3 SP1 4 SP2 3 SP1 9E69 6 9ED9 5 9EE9 4 ROL ADC ADC 3 SP1 4 SP2 3 SP1 9E6A 6 9EDA 5 9EEA 4 DEC ORA ORA 3 SP1 4 SP2 3 SP1 9E6B 8 9EDB 5 9EEB 4 DBNZ ADD ADD 4 SP1 4 SP2 3 SP1 9E6C 6 INC 3 SP1 9E6D 5 TST 3 SP1 9EAE 5 9EBE 6 9ECE 5 9EDE 5 9EEE 4 9EFE 5 LDHX LDHX LDHX LDX LDX LDHX 2 IX 4 IX2 3 IX1 4 SP2 3 SP1 3 SP1 9E6F 6 9EDF 5 9EEF 4 9EFF 5 CLR STX STX STHX 3 SP1 4 SP2 3 SP1 3 SP1 INH Inherent REL Relative SP1 Stack Pointer, 8-Bit Offset IMM Immediate IX Indexed, No Offset SP2 Stack Pointer, 16-Bit Offset DIR Direct IX1 Indexed, 8-Bit Offset IX+ Indexed, No Offset with EXT Extended IX2 Indexed, 16-Bit Offset Post Increment DD DIR to DIR IMD IMM to DIR IX1+ Indexed, 1-Byte Offset with IX+D IX+ to DIR DIX+ DIR to IX+ Post Increment Note: All Sheet 2 Opcodes are Preceded by the Page 2 Prebyte (9E) Prebyte (9E) and Opcode in Hexadecimal 9E60 6 HCS08 Cycles NEG Instruction Mnemonic Number of Bytes 3 SP1 Addressing Mode MC9S08JM60 Series Data Sheet, Rev. 5 118 Freescale Semiconductor

Chapter 8 5 V Analog Comparator (S08ACMPV2) 8.1 Introduction The analog comparator module (ACMP) provides a circuit for comparing two analog input voltages or for comparing one analog input voltage to an internal reference voltage. The comparator circuit is designed to operate across the full range of the supply voltage (rail to rail operation). NOTE MC9S08JM60 series devices operate at a higher voltage range (2.7 V to 5.5V) and do not include stop1 mode. Therefore, please disregard references to stop1. 8.1.1 ACMP Configuration Information When using the bandgap reference voltage for input to ACMP+, the user must enable the bandgap buffer by setting BGBE =1 in SPMSC1 see Section5.7.7, “System Power Management Status and Control 1 Register (SPMSC1).” For value of bandgap voltage reference see AppendixA.6, “DC Characteristics.” 8.1.2 ACMP/TPM Configuration Information The ACMP module can be configured to connect the output of the analog comparator to TPM input capture channel 0 by setting ACIC in SOPT2. With ACIC set, the TPM1CH0 pin is not available externally regardless of the configuration of the TPM module. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 119

Chapter8 5 V Analog Comparator (S08ACMPV2) USBDP ON-CHIP ICE AND USBDN HCS08 CORE DEBUG MODULE (DBG) A T 6 R PTA5– PTA0 O USB SIE P BKGD/MS FULL SPEED PTB7/ADP7 BDC CPU USB PTB6/ADP6 USB ENDPOINT TRANSCEIVER PTB5/KBIP5/ADP5 RAM B T PTB4/KBIP4/ADP4 SSPSS2CK2 POR PTB3/SS2/ADP3 RESET HCS08 SYSTEM CONTROL 8-/16-BIT SERIAL PERIPHERAL MOSI2 PTB2/SPSCK2/ADP2 INTERFACE MODULE (SPI2) PTB1/MOSI2/ADP1 MISO2 PTB0/MISO2/ADP0 RESETS AND INTERRUPTS MODES OF OPERATION PTC6 IRQ/TPMCLK POWER MANAGEMENT SERIAL COMMUNICATIONS RxD2 PTC5/RxD2 COP IRQ LVD INTERFACE MODULE (SCI2) TxD2 ORT C PPTTCC34/TxD2 P PTC2 SDA PTC1/SDA IIC MODULE (IIC) SCL PTC0/SCL VDDAD 12-CHANNEL, 12-BIT 8 PTD7 VSSAD ANALOG-TO-DIGITAL 4 PTD6 VREFL CONVERTER (ADC) PTD5 VREFH D PTD4/ADP11 T R PTD3/KBIP3/ADP10 O USER Flash (IN BYTES) P PTD2/KBIP2/ACMPO ACMP– MC9S08JM60 = 60,912 PTD1/ADP9/ACMP– MC9S08JM32 = 32,768 ANALOG COMPARATOR ACMP+ PTD0/ADP8/ACMP+ (ACMP) ACMPO SS1 PTE7/SS1 USER RAM (IN BYTES) SPSCK1 8-/16-BIT SERIAL PERIPHERAL PTE6/SPSCK1 MMCC99SS0088JJMM6302 == 42009468 INTERFACE MODULE (SPI1) MOSI1 PTE5/MOSI1 MISO1 PTE4/MISO1 TPMCLK E MULTI-PURPOSE CLOCK 6-CHMAONDNUELLE T (ITMPEMR1/P)WM TTPPMM11CCHH10 PORT PTE3/TPM1CH1 GENERATOR (MCG) PTE2/TPM1CH0 TPM1CHx4 RxD1 SERIAL COMMUNICATIONS PTE1/RxD1 VSSOSC LOW-POWER OSCILLATOR TxD1 PTE0/TxD1 INTERFACE MODULE (SCI1) PTF7 VDD SYSTEM TPMCLK PTF6 VSS RVEOGLUTLAAGTEO R 2-CHMAONDNUELLE T (ITMPEMR2/P)WM TTPPMM22CCHH10 T F PPTTFF54//TTPPMM22CCHH10 OR PTF3/TPM1CH5 KBIPx P PTF2/TPM1CH4 VUSB33 USB 3.3-V VOLTAGE REGULATOR 8-BIT KEYBOARD 4 PTF1/TPM1CH3 INTERRUPT MODULE (KBI) KBIPx 4 PTF0/TPM1CH2 REAL-TIME COUNTER (RTC) EXTAL PTG5/EXTAL XTAL NOTES: G PTG4/XTAL 1. Port pins are software configurable with pullup device if input port. RT PTG3/KBIP7 O PTG2/KBIP6 2. Pin contains software configurable pullup/pull-down device if IRQ is enabled P PTG1/KBIP1 (IRQPE=1). Pull-down is enabled if rising edge detect is selected (IRQEDG=1) PTG0/KBIP0 3. IRQ does not have a clamp diode to V . IRQ must not be driven above V . DD DD 4. Pin contains integrated pullup device. 5. When pin functions as KBI (KBIPEn = 1) and associated pin is configured to enable the pullup device, KBEDGn can be used to reconfigure the pullup as a pull-down device. Figure8-1. MC9S08JM60 Series Block Diagram Highlighting ACMP Block and Pins MC9S08JM60 Series Data Sheet, Rev. 5 120 Freescale Semiconductor

Analog Comparator (S08ACMPV2) 8.1.3 Features The ACMP has the following features: • Full rail to rail supply operation. • Selectable interrupt on rising edge, falling edge, or either rising or falling edges of comparator output. • Option to compare to fixed internal bandgap reference voltage. • Option to allow comparator output to be visible on a pin, ACMPO. • Can operate in stop3 mode 8.1.4 Modes of Operation This section defines the ACMP operation in wait, stop and background debug modes. 8.1.4.1 ACMP in Wait Mode The ACMP continues to run in wait mode if enabled before executing the WAIT instruction. Therefore, the ACMP can be used to bring the MCU out of wait mode if the ACMP interrupt, ACIE is enabled. For lowest possible current consumption, the ACMP must be disabled by software if not required as an interrupt source during wait mode. 8.1.4.2 ACMP in Stop Modes 8.1.4.2.1 Stop3 Mode Operation The ACMP continues to operate in stop3 mode if enabled and compare operation remains active. If ACOPE is enabled, comparator output operates as in the normal operating mode and comparator output is placed onto the external pin. The MCU is brought out of stop when a compare event occurs and ACIE is enabled; ACF flag sets accordingly. If stop is exited with a reset, the ACMP will be put into its reset state. 8.1.4.2.2 Stop2 and Stop1 Mode Operation During either stop2 and stop1 mode, the ACMP module will be fully powered down. Upon wake-up from stop2 or stop1 mode, the ACMP module will be in the reset state. 8.1.4.3 ACMP in Active Background Mode When the microcontroller is in active background mode, the ACMP will continue to operate normally. 8.1.5 Block Diagram The block diagram for the Analog Comparator module is shown Figure8-2. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 121

Analog Comparator (S08ACMPV2) Internal Bus Internal Reference ACMP INTERRUPT ACIE REQUEST ACBGS Status & Control ACME ACF Register ACOPE D F O C M A ACMP+ AC set + Interrupt Control - ACMP– Comparator ACMPO Figure8-2. Analog Comparator 5V (ACMP5) Block Diagram 8.2 External Signal Description The ACMP has two analog input pins, ACMP+ and ACMP– and one digital output pin ACMPO. Each of these pins can accept an input voltage that varies across the full operating voltage range of the MCU. As shown in Figure 8-2, the ACMP– pin is connected to the inverting input of the comparator, and the ACMP+ pin is connected to the comparator non-inverting input if ACBGS is a 0. As shown in Figure8-2, the ACMPO pin can be enabled to drive an external pin. The signal properties of ACMP are shown in Table 8-1. Table8-1. Signal Properties Signal Function I/O ACMP– Inverting analog input to the ACMP. I (Minus input) ACMP+ Non-inverting analog input to the ACMP. I (Positive input) ACMPO Digital output of the ACMP. O 8.3 Memory Map 8.3.1 Register Descriptions The ACMP includes one register: MC9S08JM60 Series Data Sheet, Rev. 5 122 Preliminary Freescale Semiconductor

Analog Comparator (S08ACMPV2) • An 8-bit status and control register Refer to the direct-page register summary in the memory section of this data sheet for the absolute address assignments for all ACMP registers.This section refers to registers and control bits only by their names. Some MCUs may have more than one ACMP, so register names include placeholder characters to identify which ACMP is being referenced. 8.3.1.1 ACMP Status and Control Register (ACMPSC) ACMPSC contains the status flag and control bits which are used to enable and configure the ACMP. 7 6 5 4 3 2 1 0 R ACO ACME ACBGS ACF ACIE ACOPE ACMOD W Reset: 0 0 0 0 0 0 0 0 = Unimplemented Figure8-3. ACMP Status and Control Register Table8-2. ACMP Status and Control Register Field Descriptions Field Description 7 Analog Comparator Module Enable — ACME enables the ACMP module. ACME 0 ACMP not enabled 1 ACMP is enabled 6 Analog Comparator Bandgap Select — ACBGS is used to select between the bandgap reference voltage or ACBGS the ACMP+ pin as the input to the non-inverting input of the analog comparatorr. 0 External pin ACMP+ selected as non-inverting input to comparator 1 Internal reference select as non-inverting input to comparator Note: refer to this chapter introduction to verify if any other config bits are necessary to enable the bandgap reference in the chip level. 5 Analog Comparator Flag — ACF is set when a compare event occurs. Compare events are defined by ACMOD. ACF ACF is cleared by writing a one to ACF. 0 Compare event has not occurred 1 Compare event has occurred 4 Analog Comparator Interrupt Enable — ACIE enables the interrupt from the ACMP. When ACIE is set, an ACIE interrupt will be asserted when ACF is set. 0 Interrupt disabled 1 Interrupt enabled 3 Analog Comparator Output — Reading ACO will return the current value of the analog comparator output. ACO ACO is reset to a 0 and will read as a 0 when the ACMP is disabled (ACME = 0). MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 123

Analog Comparator (S08ACMPV2) Table8-2. ACMP Status and Control Register Field Descriptions (continued) Field Description 2 Analog Comparator Output Pin Enable — ACOPE is used to enable the comparator output to be placed onto ACOPE the external pin, ACMPO. 0 Analog comparator output not available on ACMPO 1 Analog comparator output is driven out on ACMPO 1:0 Analog Comparator Mode — ACMOD selects the type of compare event which sets ACF. ACMOD 00 Encoding 0 — Comparator output falling edge 01 Encoding 1 — Comparator output rising edge 10 Encoding 2 — Comparator output falling edge 11 Encoding 3 — Comparator output rising or falling edge 8.4 Functional Description The analog comparator can be used to compare two analog input voltages applied to ACMP+ and ACMP–; or it can be used to compare an analog input voltage applied to ACMP– with an internal bandgap reference voltage. ACBGS is used to select between the bandgap reference voltage or the ACMP+ pin as the input to the non-inverting input of the analog comparator. The comparator output is high when the non-inverting input is greater than the inverting input, and is low when the non-inverting input is less than the inverting input. ACMOD is used to select the condition which will cause ACF to be set. ACF can be set on a rising edge of the comparator output, a falling edge of the comparator output, or either a rising or a falling edge (toggle). The comparator output can be read directly through ACO. The comparator output can be driven onto the ACMPO pin using ACOPE. MC9S08JM60 Series Data Sheet, Rev. 5 124 Preliminary Freescale Semiconductor

Chapter 9 Keyboard Interrupt (S08KBIV2) 9.1 Introduction The MC9S08JM60 series have one KBI module with eight keyboard interrupt inputs. See Chapter 2, “Pins and Connections,” for more information about the logic and hardware aspects of these pins. NOTE MC9S08JM60 series devices operate at a higher voltage range (2.7 V to 5.5V) and do not include stop1 mode. Therefore, please disregard references to stop1. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 125

Keyboard Interrupt (KBI) ModuleChapter9 Keyboard Interrupt (S08KBIV2) USBDP ON-CHIP ICE AND USBDN HCS08 CORE DEBUG MODULE (DBG) A T 6 R PTA5– PTA0 O USB SIE P BKGD/MS FULL SPEED PTB7/ADP7 BDC CPU USB PTB6/ADP6 USB ERNADMPOINT TRANSCEIVER B PTB5/KBIP5/ADP5 T PTB4/KBIP4/ADP4 SSPSS2CK2 POR PTB3/SS2/ADP3 RESET HCS08 SYSTEM CONTROL 8-/16-BIT SERIAL PERIPHERAL MOSI2 PTB2/SPSCK2/ADP2 INTERFACE MODULE (SPI2) PTB1/MOSI2/ADP1 MISO2 PTB0/MISO2/ADP0 RESETS AND INTERRUPTS MODES OF OPERATION PTC6 IRQ/TPMCLK POWER MANAGEMENT SERIAL COMMUNICATIONS RxD2 PTC5/RxD2 COP IRQ LVD INTERFACE MODULE (SCI2) TxD2 ORT C PPTTCC34/TxD2 P PTC2 SDA PTC1/SDA IIC MODULE (IIC) SCL PTC0/SCL VDDAD 12-CHANNEL, 12-BIT 8 PTD7 VSSAD ANALOG-TO-DIGITAL 4 PTD6 VREFL CONVERTER (ADC) PTD5 VREFH D PTD4/ADP11 T R PTD3/KBIP3/ADP10 O USER Flash (IN BYTES) P PTD2/KBIP2/ACMPO ACMP– MC9S08JM60 = 60,912 PTD1/ADP9/ACMP– MC9S08JM32 = 32,768 ANALOG COMPARATOR ACMP+ PTD0/ADP8/ACMP+ (ACMP) ACMPO SS1 PTE7/SS1 USER RAM (IN BYTES) SPSCK1 8-/16-BIT SERIAL PERIPHERAL PTE6/SPSCK1 MMCC99SS0088JJMM6302 == 42009468 INTERFACE MODULE (SPI1) MOSI1 PTE5/MOSI1 MISO1 PTE4/MISO1 TPMCLK E MULTI-PURPOSE CLOCK 6-CHMAONDNUELLE T (IMTPEMR1/P)WM TTPPMM11CCHH10 PORT PTE3/TPM1CH1 GENERATOR (MCG) PTE2/TPM1CH0 TPM1CHx4 RxD1 SERIAL COMMUNICATIONS PTE1/RxD1 VSSOSC LOW-POWER OSCILLATOR TxD1 PTE0/TxD1 INTERFACE MODULE (SCI1) PTF7 VDD SYSTEM TPMCLK PTF6 VSS RVEOGLUTLAAGTEO R 2-CHMAONDNUELLE T (IMTPEMR2/P)WM TTPPMM22CCHH10 T F PPTTFF54//TTPPMM22CCHH10 OR PTF3/TPM1CH5 KBIPx P PTF2/TPM1CH4 VUSB33 USB 3.3-V VOLTAGE REGULATOR 8-BIT KEYBOARD 4 PTF1/TPM1CH3 INTERRUPT MODULE (KBI) KBIPx 4 PTF0/TPM1CH2 REAL-TIME COUNTER (RTC) EXTAL PTG5/EXTAL XTAL NOTES: G PTG4/XTAL 1. Port pins are software configurable with pullup device if input port. RT PTG3/KBIP7 O PTG2/KBIP6 2. Pin contains software configurable pullup/pull-down device if IRQ is enabled P PTG1/KBIP1 (IRQPE=1). Pull-down is enabled if rising edge detect is selected (IRQEDG=1) PTG0/KBIP0 3. IRQ does not have a clamp diode to V . IRQ must not be driven above V . DD DD 4. Pin contains integrated pullup device. 5. When pin functions as KBI (KBIPEn = 1) and associated pin is configured to enable the pullup device, KBEDGn can be used to reconfigure the pullup as a pull-down device. Figure9-1. MC9S08JM60 Series Block Diagram Highlighting KBI Block and Pins MC9S08JM60 Series Data Sheet, Rev. 5 126 Freescale Semiconductor

Keyboard Interrupts (S08KBIV2) 9.1.1 Features The KBI features include: • Up to eight keyboard interrupt pins with individual pin enable bits. • Each keyboard interrupt pin is programmable as falling edge (or rising edge) only, or both falling edge and low level (or both rising edge and high level) interrupt sensitivity. • One software enabled keyboard interrupt. • Exit from low-power modes. 9.1.2 Modes of Operation This section defines the KBI operation in wait, stop, and background debug modes. 9.1.2.1 KBI in Wait Mode The KBI continues to operate in wait mode if enabled before executing the WAIT instruction. Therefore, an enabled KBI pin (KBPEx = 1) can be used to bring the MCU out of wait mode if the KBI interrupt is enabled (KBIE = 1). 9.1.2.2 KBI in Stop Modes The KBI operates asynchronously in stop3 mode if enabled before executing the STOP instruction. Therefore, an enabled KBI pin (KBPEx = 1) can be used to bring the MCU out of stop3 mode if the KBI interrupt is enabled (KBIE = 1). During either stop1 or stop2 mode, the KBI is disabled. In some systems, the pins associated with the KBI may be sources of wakeup from stop1 or stop2, see the stop modes section in the Modes of Operation chapter. Upon wake-up from stop1 or stop2 mode, the KBI module will be in the reset state. 9.1.2.3 KBI in Active Background Mode When the microcontroller is in active background mode, the KBI will continue to operate normally. 9.1.3 Block Diagram The block diagram for the keyboard interrupt module is shown Figure 9-2. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 127

Keyboard Interrupts (S08KBIV2) KBACK BUSCLK 1 VDD RESET KBF KBIP0 0S KBIPE0 DCLRQ SYNCHRONIZER CK KBEDG0 KEYBOARD STOP STOP BYPASS KBI INTERRUPT FF INTERRUPT 1 REQUEST KBIPn 0 S KBIPEn KBMOD KBIE KBEDGn Figure9-2. KBI Block Diagram 9.2 External Signal Description The KBI input pins can be used to detect either falling edges, or both falling edge and low level interrupt requests. The KBI input pins can also be used to detect either rising edges, or both rising edge and high level interrupt requests. The signal properties of KBI are shown in Table 9-1. Table9-1. Signal Properties Signal Function I/O KBIPn Keyboard interrupt pins I 9.3 Register Definition The KBI includes three registers: • An 8-bit pin status and control register. • An 8-bit pin enable register. • An 8-bit edge select register. Refer to the direct-page register summary in the Memory chapter for the absolute address assignments for all KBI registers. This section refers to registers and control bits only by their names. Some MCUs may have more than one KBI, so register names include placeholder characters to identify which KBI is being referenced. 9.3.1 KBI Status and Control Register (KBISC) KBISC contains the status flag and control bits, which are used to configure the KBI. MC9S08JM60 Series Data Sheet, Rev. 5 128 Freescale Semiconductor

Keyboard Interrupts (S08KBIV2) 7 6 5 4 3 2 1 0 R 0 0 0 0 KBF 0 KBIE KBMOD W KBACK Reset: 0 0 0 0 0 0 0 0 = Unimplemented Figure9-3. KBI Status and Control Register Table9-2. KBISC Register Field Descriptions Field Description 7:4 Unused register bits, always read 0. 3 Keyboard Interrupt Flag — KBF indicates when a keyboard interrupt is detected. Writes have no effect on KBF. KBF 0 No keyboard interrupt detected. 1 Keyboard interrupt detected. 2 Keyboard Acknowledge — Writing a 1 to KBACK is part of the flag clearing mechanism. KBACK always reads KBACK as 0. 1 Keyboard Interrupt Enable — KBIE determines whether a keyboard interrupt is requested. KBIE 0 Keyboard interrupt request not enabled. 1 Keyboard interrupt request enabled. 0 Keyboard Detection Mode — KBMOD (along with the KBEDG bits) controls the detection mode of the keyboard KBMOD interrupt pins.0Keyboard detects edges only. 1 Keyboard detects both edges and levels. 9.3.2 KBI Pin Enable Register (KBIPE) KBIPE contains the pin enable control bits. 7 6 5 4 3 2 1 0 R KBIPE7 KBIPE6 KBIPE5 KBIPE4 KBIPE3 KBIPE2 KBIPE1 KBIPE0 W Reset: 0 0 0 0 0 0 0 0 Figure9-4. KBI Pin Enable Register Table9-3. KBIPE Register Field Descriptions Field Description 7:0 Keyboard Pin Enables — Each of the KBIPEn bits enable the corresponding keyboard interrupt pin. KBIPEn 0 Pin not enabled as keyboard interrupt. 1 Pin enabled as keyboard interrupt. 9.3.3 KBI Edge Select Register (KBIES) KBIES contains the edge select control bits. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 129

Keyboard Interrupts (S08KBIV2) 7 6 5 4 3 2 1 0 R KBEDG7 KBEDG6 KBEDG5 KBEDG4 KBEDG3 KBEDG2 KBEDG1 KBEDG0 W Reset: 0 0 0 0 0 0 0 0 Figure9-5. KBI Edge Select Register Table9-4. KBIES Register Field Descriptions Field Description 7:0 Keyboard Edge Selects — Each of the KBEDGn bits selects the falling edge/low level or rising edge/high level KBEDGn function of the corresponding pin). 0 Falling edge/low level. 1 Rising edge/high level. 9.4 Functional Description This on-chip peripheral module is called a keyboard interrupt (KBI) module because originally it was designed to simplify the connection and use of row-column matrices of keyboard switches. However, these inputs are also useful as extra external interrupt inputs and as an external means of waking the MCU from stop or wait low-power modes. The KBI module allows up to eight pins to act as additional interrupt sources. Writing to the KBIPEn bits in the keyboard interrupt pin enable register (KBIPE) independently enables or disables each KBI pin. Each KBI pin can be configured as edge sensitive or edge and level sensitive based on the KBMOD bit in the keyboard interrupt status and control register (KBISC). Edge sensitive can be software programmed to be either falling or rising; the level can be either low or high. The polarity of the edge or edge and level sensitivity is selected using the KBEDGn bits in the keyboard interrupt edge select register (KBIES). 9.4.1 Edge Only Sensitivity Synchronous logic is used to detect edges. A falling edge is detected when an enabled keyboard interrupt (KBIPEn=1) input signal is seen as a logic 1 (the deasserted level) during one bus cycle and then a logic 0 (the asserted level) during the next cycle. A rising edge is detected when the input signal is seen as a logic 0 (the deasserted level) during one bus cycle and then a logic 1 (the asserted level) during the next cycle.Before the first edge is detected, all enabled keyboard interrupt input signals must be at the deasserted logic levels. After any edge is detected, all enabled keyboard interrupt input signals must return to the deasserted level before any new edge can be detected. A valid edge on an enabled KBI pin will set KBF in KBISC. If KBIE in KBISC is set, an interrupt request will be presented to the CPU. Clearing of KBF is accomplished by writing a 1 to KBACK in KBISC. 9.4.2 Edge and Level Sensitivity A valid edge or level on an enabled KBI pin will set KBF in KBISC. If KBIE in KBISC is set, an interrupt request will be presented to the CPU. Clearing of KBF is accomplished by writing a 1 to KBACK in MC9S08JM60 Series Data Sheet, Rev. 5 130 Freescale Semiconductor

Keyboard Interrupts (S08KBIV2) KBISC provided all enabled keyboard inputs are at their deasserted levels. KBF will remain set if any enabled KBI pin is asserted while attempting to clear by writing a 1 to KBACK. 9.4.3 KBI Pullup/Pulldown Resistors The KBI pins can be configured to use an internal pullup/pulldown resistor using the associated I/O port pullup enable register. If an internal resistor is enabled, the KBIES register is used to select whether the resistor is a pullup (KBEDGn = 0) or a pulldown (KBEDGn = 1). 9.4.4 KBI Initialization When a keyboard interrupt pin is first enabled it is possible to get a false keyboard interrupt flag. To prevent a false interrupt request during keyboard initialization, the user should do the following: 1. Mask keyboard interrupts by clearing KBIE in KBISC. 2. Enable the KBI polarity by setting the appropriate KBEDGn bits in KBIES. 3. If using internal pullup/pulldown device, configure the associated pullup enable bits in PTxPE. 4. Enable the KBI pins by setting the appropriate KBIPEn bits in KBIPE. 5. Write to KBACK in KBISC to clear any false interrupts. 6. Set KBIE in KBISC to enable interrupts. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 131

Keyboard Interrupts (S08KBIV2) MC9S08JM60 Series Data Sheet, Rev. 5 132 Freescale Semiconductor

Chapter 10 Analog-to-Digital Converter (S08ADC12V1) 10.1 Overview The 12-bit analog-to-digital converter (ADC) is a successive approximation ADC designed for operation within an integrated microcontroller system-on-chip. NOTE MC9S08JM60 series devices operate at a higher voltage range (2.7 V to 5.5V) and do not include stop1 mode. Therefore, please disregard references to stop1. 10.1.1 Module Configurations This section provides information for configuring the ADC on this device. 10.1.1.1 Channel Assignments The ADC channel assignments for the MC9S08JM60 Series devices are shown in the table below. Reserved channels convert to an unknown value. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 133

Chapter10 Analog-to-Digital Converter (S08ADC12V1) Table10-1. ADC Channel Assignment ADCH Channel Input Pin Control ADCH Channel Input Pin Control 00000 AD0 PTB0/MISO2/ADP0 ADPC0 10000 AD16 V N/A REFL 00001 AD1 PTB1/MOSI2/ADP1 ADPC1 10001 AD17 V N/A REFL 00010 AD2 PTB2/SPSCK2/ADP2 ADPC2 10010 AD18 V N/A REFL 00011 AD3 PTB3/SS2/ADP3 ADPC3 10011 AD19 V N/A REFL 00100 AD4 PTB4/KBIP4/ADP4 ADPC4 10100 AD20 V N/A REFL 00101 AD5 PTB5/KBIP5/ADP5 ADPC5 10101 AD21 Reserved N/A 00110 AD6 PTB6/ADP6 ADPC6 10110 AD22 Reserved N/A 00111 AD7 PTB7/ADP7 ADPC7 10111 AD23 Reserved N/A 01000 AD8 PTD0/ADP8/ACMP+ ADPC8 11000 AD24 Reserved N/A 01001 AD9 PTD1/ADP9/ACMP- ADPC9 11001 AD25 Reserved N/A 01010 AD10 PTD3/KBIP3/ADP10 ADPC10 11010 AD26 Temperature N/A Sensor1 01011 AD11 PTD4/ADP11 ADPC11 11011 AD27 Internal Bandgap N/A 01100 AD12 V ADPC12 11100 Reserved N/A REFL 01101 AD13 V ADPC13 11101 V V N/A REFL REFH REFH 01110 AD14 V ADPC14 11110 V V N/A REFL REFL REFL 01111 AD15 V ADPC15 11111 module None N/A REFL disabled 1 For more information, see Section10.1.1.5, “Temperature Sensor.” NOTE Selecting the internal bandgap channel requires BGBE =1 in SPMSC1 see Section5.7.7, “System Power Management Status and Control 1 Register (SPMSC1).” For value of bandgap voltage reference see AppendixA.8, “Analog Comparator (ACMP) Electricals.” 10.1.1.2 Alternate Clock The ADC is capable of performing conversions using the MCU bus clock, the bus clock divided by two, the local asynchronous clock (ADACK) within the module, or the alternate clock (ALTCLK). The ALTCLK on this device is the MCGERCLK. The selected clock source must run at a frequency such that the ADC conversion clock (ADCK) runs at a frequency within its specified range (f ) after being divided down from the ALTCLK input as ADCK determined by the ADIV bits. ALTCLK is active while the MCU is in wait mode provided the conditions described above are met. This allows ALTCLK to be used as the conversion clock source for the ADC while the MCU is in wait mode. ALTCLK cannot be used as the ADC conversion clock source while the MCU is in stop3. 10.1.1.3 Hardware Trigger The RTC on this device can be enabled as a hardware trigger for the ADC module by setting the MC9S08JM60 Series Data Sheet, Rev. 5 134 Freescale Semiconductor

Chapter10 Analog-to-Digital Converter (S08ADC12V1) ADCSC2[ADTRG] bit. When enabled, the ADC will be triggered every time RTCINT matches RTCMOD. The RTC interrupt does not have to be enabled to trigger the ADC. The RTC can be configured to cause a hardware trigger in MCU run, wait, and stop3. 10.1.1.4 Analog Pin Enables The ADC on MC9S08JM60 series contains only two analog pin enable registers, APCTL1 and APCTL2. 10.1.1.5 Temperature Sensor The ADC module includes a temperature sensor whose output is connected to one of the ADC analog channel inputs. Equation10-1 provides an approximate transfer function of the temperature sensor. Temp = 25 – ((V – V ) ÷ m) Eqn.10-1 TEMP TEMP25 where: — V is the voltage of the temperature sensor channel at the ambient temperature. TEMP — V is the voltage of the temperature sensor channel at 25°C. TEMP25 — m is the hot or cold voltage versus temperature slope in V/°C. For temperature calculations, use the V and m values from the ADC Electricals table. TEMP25 In application code, the user reads the temperature sensor channel, calculates V , and compares to TEMP V . If V is greater than V , the cold slope value is applied in Equation10-1. If V TEMP25 TEMP TEMP25 TEMP is less than V the hot slope value is applied in Equation10-1. TEMP25 To improve accuracy, calibrate the bandgap voltage reference and temperature sensor. Calibrating at 25 °C will improve accuracy to ±4.5°C. Calibration at 3 points, –40°C, 25°C, and 125°C will improve accuracy to ±2.5°C. Once calibration has been completed, the user will need to calculate the slope for both hot and cold. In application code, the user would then calculate the temperature using Equation10-1 as detailed above and then determine if the temperature is above or below 25°C. Once determined, if the temperature is above or below 25°C, the user can recalculate the temperature using the hot or cold slope value obtained during calibration. 10.1.2 Low-Power Mode Operation The ADC is capable of running in stop3 mode but requires LVDSE and LVDE in SPMSC1 to be set. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 135

Chapter10 Analog-to-Digital Converter (S08ADC12V1) USBDP ON-CHIP ICE AND USBDN HCS08 CORE DEBUG MODULE (DBG) A T 6 R PTA5– PTA0 O USB SIE P BKGD/MS FULL SPEED PTB7/ADP7 BDC CPU USB PTB6/ADP6 USB ERNADMPOINT TRANSCEIVER B PTB5/KBIP5/ADP5 T PTB4/KBIP4/ADP4 SSPSS2CK2 POR PTB3/SS2/ADP3 RESET HCS08 SYSTEM CONTROL 8-/16-BIT SERIAL PERIPHERAL MOSI2 PTB2/SPSCK2/ADP2 INTERFACE MODULE (SPI2) PTB1/MOSI2/ADP1 MISO2 PTB0/MISO2/ADP0 RESETS AND INTERRUPTS MODES OF OPERATION PTC6 IRQ/TPMCLK POWER MANAGEMENT SERIAL COMMUNICATIONS RxD2 PTC5/RxD2 COP IRQ LVD INTERFACE MODULE (SCI2) TxD2 ORT C PPTTCC34/TxD2 P PTC2 SDA PTC1/SDA IIC MODULE (IIC) SCL PTC0/SCL VDDAD 12-CHANNEL, 12-BIT 8 PTD7 VSSAD ANALOG-TO-DIGITAL 4 PTD6 VREFL CONVERTER (ADC) PTD5 VREFH D PTD4/ADP11 T R PTD3/KBIP3/ADP10 O USER Flash (IN BYTES) P PTD2/KBIP2/ACMPO ACMP– MC9S08JM60 = 60,912 PTD1/ADP9/ACMP– MC9S08JM32 = 32,768 ANALOG COMPARATOR ACMP+ PTD0/ADP8/ACMP+ (ACMP) ACMPO SS1 PTE7/SS1 USER RAM (IN BYTES) SPSCK1 8-/16-BIT SERIAL PERIPHERAL PTE6/SPSCK1 MMCC99SS0088JJMM6302 == 42009468 INTERFACE MODULE (SPI1) MOSI1 PTE5/MOSI1 MISO1 PTE4/MISO1 TPMCLK E MULTI-PURPOSE CLOCK 6-CHMAONDNUELLE T (ITMPEMR1/P)WM TTPPMM11CCHH10 PORT PTE3/TPM1CH1 GENERATOR (MCG) PTE2/TPM1CH0 TPM1CHx4 RxD1 SERIAL COMMUNICATIONS PTE1/RxD1 VSSOSC LOW-POWER OSCILLATOR TxD1 PTE0/TxD1 INTERFACE MODULE (SCI1) PTF7 VDD SYSTEM TPMCLK PTF6 VSS RVEOGLUTLAAGTEO R 2-CHMAONDNUELLE T (ITMPEMR2/P)WM TTPPMM22CCHH10 T F PPTTFF54//TTPPMM22CCHH10 OR PTF3/TPM1CH5 KBIPx P PTF2/TPM1CH4 VUSB33 USB 3.3-V VOLTAGE REGULATOR 8-BIT KEYBOARD 4 PTF1/TPM1CH3 INTERRUPT MODULE (KBI) KBIPx 4 PTF0/TPM1CH2 REAL-TIME COUNTER (RTC) EXTAL PTG5/EXTAL XTAL NOTES: G PTG4/XTAL 1. Port pins are software configurable with pullup device if input port. RT PTG3/KBIP7 O PTG2/KBIP6 2. Pin contains software configurable pullup/pull-down device if IRQ is enabled P PTG1/KBIP1 (IRQPE=1). Pull-down is enabled if rising edge detect is selected (IRQEDG=1) PTG0/KBIP0 3. IRQ does not have a clamp diode to V . IRQ must not be driven above V . DD DD 4. Pin contains integrated pullup device. 5. When pin functions as KBI (KBIPEn = 1) and associated pin is configured to enable the pullup device, KBEDGn can be used to reconfigure the pullup as a pull-down device. Figure10-1. MC9S08JM60 Series Block Diagram Highlighting ADC Block and Pins MC9S08JM60 Series Data Sheet, Rev. 5 136 Freescale Semiconductor

Analog-to-Digital Converter (S08ADC12V1) 10.1.3 Features Features of the ADC module include: • Linear successive approximation algorithm with 12-bit resolution • Up to 28 analog inputs • Output formatted in 12-, 10-, or 8-bit right-justified unsigned format • Single or continuous conversion (automatic return to idle after single conversion) • Configurable sample time and conversion speed/power • Conversion complete flag and interrupt • Input clock selectable from up to four sources • Operation in wait or stop3 modes for lower noise operation • Asynchronous clock source for lower noise operation • Selectable asynchronous hardware conversion trigger • Automatic compare with interrupt for less-than, or greater-than or equal-to, programmable value • Temperature sensor 10.1.4 ADC Module Block Diagram Figure 10-2 provides a block diagram of the ADC module. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 137

Analog-to-Digital Converter (S08ADC12V1) 3 Compare true ADCSC1 ADCCFG O N C ADCH AIE1 CO2 ADCO complete ADTRG MODE ADLSMP ADLPC ADIV ADICLK CloAcsky Gncen ADACK Bus Clock MCU STOP ADCK Clock ADHWT Control Sequencer Divide ÷2 AD0 initialize sample convert transfer abort ALTCLK • AIEN 1 Interrupt • • ADVIN COCO 2 SAR Converter AD27 V REFH Data Registers V REFL m u S Compare true 3 Compare Logic Value CFGT A Compare Value Registers ADCSC2 Figure10-2. ADC Block Diagram 10.2 External Signal Description The ADC module supports up to 28 separate analog inputs. It also requires four supply/reference/ground connections. Table10-2. Signal Properties Name Function AD27–AD0 Analog Channel inputs V High reference voltage REFH V Low reference voltage REFL V Analog power supply DDAD V Analog ground SSAD MC9S08JM60 Series Data Sheet, Rev. 5 138 Freescale Semiconductor

Analog-to-Digital Converter (S08ADC12V1) 10.2.1 Analog Power (V ) DDAD The ADC analog portion uses V as its power connection. In some packages, V is connected DDAD DDAD internally to V . If externally available, connect the V pin to the same voltage potential as V . DD DDAD DD External filtering may be necessary to ensure clean V for good results. DDAD 10.2.2 Analog Ground (V ) SSAD The ADC analog portion uses V as its ground connection. In some packages, V is connected SSAD SSAD internally to V . If externally available, connect the V pin to the same voltage potential as V . SS SSAD SS 10.2.3 Voltage Reference High (V ) REFH V is the high reference voltage for the converter. In some packages, V is connected internally to REFH REFH V . If externally available, V may be connected to the same potential as V or may be driven DDAD REFH DDAD by an external source between the minimum V spec and the V potential (V must never DDAD DDAD REFH exceed V ). DDAD 10.2.4 Voltage Reference Low (V ) REFL V is the low-reference voltage for the converter. In some packages, V is connected internally to REFL REFL V . If externally available, connect the V pin to the same voltage potential as V . SSAD REFL SSAD 10.2.5 Analog Channel Inputs (ADx) The ADC module supports up to 28 separate analog inputs. An input is selected for conversion through the ADCH channel select bits. 10.3 Register Definition These memory-mapped registers control and monitor operation of the ADC: • Status and control register, ADCSC1 • Status and control register, ADCSC2 • Data result registers, ADCRH and ADCRL • Compare value registers, ADCCVH and ADCCVL • Configuration register, ADCCFG • Pin control registers, APCTL1, APCTL2, APCTL3 10.3.1 Status and Control Register 1 (ADCSC1) This section describes the function of the ADC status and control register (ADCSC1). Writing ADCSC1 aborts the current conversion and initiates a new conversion (if the ADCH bits are equal to a value other than all 1s). MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 139

Analog-to-Digital Converter (S08ADC12V1) 7 6 5 4 3 2 1 0 R COCO AIEN ADCO ADCH W Reset: 0 0 0 1 1 1 1 1 Figure10-3. Status and Control Register (ADCSC1) Table10-3. ADCSC1 Field Descriptions Field Description 7 Conversion Complete Flag. The COCO flag is a read-only bit set each time a conversion is completed when the COCO compare function is disabled (ACFE = 0). When the compare function is enabled (ACFE = 1), the COCO flag is set upon completion of a conversion only if the compare result is true. This bit is cleared when ADCSC1 is written or when ADCRL is read. 0 Conversion not completed 1 Conversion completed 6 Interrupt Enable AIEN enables conversion complete interrupts. When COCO becomes set while AIEN is high, AIEN an interrupt is asserted. 0 Conversion complete interrupt disabled 1 Conversion complete interrupt enabled 5 Continuous Conversion Enable. ADCO enables continuous conversions. ADCO 0 One conversion following a write to the ADCSC1 when software triggered operation is selected, or one conversion following assertion of ADHWT when hardware triggered operation is selected. 1 Continuous conversions initiated following a write to ADCSC1 when software triggered operation is selected. Continuous conversions are initiated by an ADHWT event when hardware triggered operation is selected. 4:0 Input Channel Select. The ADCH bits form a 5-bit field that selects one of the input channels. The input channels ADCH are detailed in Table10-4. The successive approximation converter subsystem is turned off when the channel select bits are all set. This feature allows for explicit disabling of the ADC and isolation of the input channel from all sources. Terminating continuous conversions this way prevents an additional, single conversion from being performed. It is not necessary to set the channel select bits to all ones to place the ADC in a low-power state when continuous conversions are not enabled because the module automatically enters a low-power state when a conversion completes. Table10-4. Input Channel Select ADCH Input Select 00000–01111 AD0–15 10000–11011 AD16–27 11100 Reserved 11101 V REFH 11110 V REFL 11111 Module disabled MC9S08JM60 Series Data Sheet, Rev. 5 140 Freescale Semiconductor

Analog-to-Digital Converter (S08ADC12V1) 10.3.2 Status and Control Register 2 (ADCSC2) The ADCSC2 register controls the compare function, conversion trigger, and conversion active of the ADC module. 7 6 5 4 3 2 1 0 R ADACT 0 0 ADTRG ACFE ACFGT R1 R1 W Reset: 0 0 0 0 0 0 0 0 1 Bits 1 and 0 are reserved bits that must always be written to 0. Figure10-4. Status and Control Register 2 (ADCSC2) Table10-5. ADCSC2 Register Field Descriptions Field Description 7 Conversion Active. Indicates that a conversion is in progress. ADACT is set when a conversion is initiated and ADACT cleared when a conversion is completed or aborted. 0 Conversion not in progress 1 Conversion in progress 6 Conversion Trigger Select. Selects the type of trigger used for initiating a conversion. Two types of triggers are ADTRG selectable: software trigger and hardware trigger. When software trigger is selected, a conversion is initiated following a write to ADCSC1. When hardware trigger is selected, a conversion is initiated following the assertion of the ADHWT input. 0 Software trigger selected 1 Hardware trigger selected 5 Compare Function Enable. Enables the compare function. ACFE 0 Compare function disabled 1 Compare function enabled 4 Compare Function Greater Than Enable. Configures the compare function to trigger when the result of the ACFGT conversion of the input being monitored is greater than or equal to the compare value. The compare function defaults to triggering when the result of the compare of the input being monitored is less than the compare value. 0 Compare triggers when input is less than compare value 1 Compare triggers when input is greater than or equal to compare value 10.3.3 Data Result High Register (ADCRH) In 12-bit operation, ADCRH contains the upper four bits of the result of a 12-bit conversion. In 10-bit mode, ADCRH contains the upper two bits of the result of a 10-bit conversion. When configured for 10-bit mode, ADR[11:10] are cleared. When configured for 8-bit mode, ADR[11:8] are cleared. In 12-bit and 10-bit mode, ADCRH is updated each time a conversion completes except when automatic compare is enabled and the compare condition is not met. When a compare event does occur, the value is the addition of the conversion result and the two’s complement of the compare value. In 12-bit and 10-bit mode, reading ADCRH prevents the ADC from transferring subsequent conversion results into the result registers until ADCRL is read. If ADCRL is not read until after the next conversion is completed, the intermediate conversion result is lost. In 8-bit mode, there is no interlocking with ADCRL. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 141

Analog-to-Digital Converter (S08ADC12V1) If the MODE bits are changed, any data in ADCRH becomes invalid. 7 6 5 4 3 2 1 0 R 0 0 0 0 ADR11 ADR10 ADR9 ADR8 W Reset: 0 0 0 0 0 0 0 0 Figure10-5. Data Result High Register (ADCRH) 10.3.4 Data Result Low Register (ADCRL) ADCRL contains the lower eight bits of the result of a 12-bit or 10-bit conversion, and all eight bits of an 8-bit conversion. This register is updated each time a conversion completes except when automatic compare is enabled and the compare condition is not met. In 12-bit and 10-bit mode, reading ADCRH prevents the ADC from transferring subsequent conversion results into the result registers until ADCRL is read. If ADCRL is not read until the after next conversion is completed, the intermediate conversion results are lost. In 8-bit mode, there is no interlocking with ADCRH. If the MODE bits are changed, any data in ADCRL becomes invalid. 7 6 5 4 3 2 1 0 R ADR7 ADR6 ADR5 ADR4 ADR3 ADR2 ADR1 ADR0 W Reset: 0 0 0 0 0 0 0 0 Figure10-6. Data Result Low Register (ADCRL) 10.3.5 Compare Value High Register (ADCCVH) In 12-bit mode, the ADCCVH register holds the upper four bits of the 12-bit compare value. When the compare function is enabled, these bits are compared to the upper four bits of the result following a conversion in 12-bit mode. 7 6 5 4 3 2 1 0 R 0 0 0 0 ADCV11 ADCV10 ADCV9 ADCV8 W Reset: 0 0 0 0 0 0 0 0 Figure10-7. Compare Value High Register (ADCCVH) MC9S08JM60 Series Data Sheet, Rev. 5 142 Freescale Semiconductor

Analog-to-Digital Converter (S08ADC12V1) In 10-bit mode, the ADCCVH register holds the upper two bits of the 10-bit compare value (ADCV[9:8]). These bits are compared to the upper two bits of the result following a conversion in 10-bit mode when the compare function is enabled. In 8-bit mode, ADCCVH is not used during compare. 10.3.6 Compare Value Low Register (ADCCVL) This register holds the lower 8 bits of the 12-bit or 10-bit compare value or all 8 bits of the 8-bit compare value. When the compare function is enabled, bits ADCV[7:0] are compared to the lower 8 bits of the result following a conversion in 12-bit, 10-bit or 8-bit mode. 7 6 5 4 3 2 1 0 R ADCV7 ADCV6 ADCV5 ADCV4 ADCV3 ADCV2 ADCV1 ADCV0 W Reset: 0 0 0 0 0 0 0 0 Figure10-8. Compare Value Low Register (ADCCVL) 10.3.7 Configuration Register (ADCCFG) ADCCFG selects the mode of operation, clock source, clock divide, and configures for low power and long sample time. 7 6 5 4 3 2 1 0 R ADLPC ADIV ADLSMP MODE ADICLK W Reset: 0 0 0 0 0 0 0 0 Figure10-9. Configuration Register (ADCCFG) Table10-6. ADCCFG Register Field Descriptions Field Description 7 Low-Power Configuration. ADLPC controls the speed and power configuration of the successive approximation ADLPC converter. This optimizes power consumption when higher sample rates are not required. 0 High speed configuration 1 Low power configuration:The power is reduced at the expense of maximum clock speed. 6:5 Clock Divide Select. ADIV selects the divide ratio used by the ADC to generate the internal clock ADCK. ADIV Table10-7 shows the available clock configurations. 4 Long Sample Time Configuration. ADLSMP selects between long and short sample time. This adjusts the ADLSMP sample period to allow higher impedance inputs to be accurately sampled or to maximize conversion speed for lower impedance inputs. Longer sample times can also be used to lower overall power consumption when continuous conversions are enabled if high conversion rates are not required. 0 Short sample time 1 Long sample time MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 143

Analog-to-Digital Converter (S08ADC12V1) Table10-6. ADCCFG Register Field Descriptions (continued) Field Description 3:2 Conversion Mode Selection. MODE bits are used to select between 12-, 10-, or 8-bit operation. See Table10-8. MODE 1:0 Input Clock Select. ADICLK bits select the input clock source to generate the internal clock ADCK. See ADICLK Table10-9. Table10-7. Clock Divide Select ADIV Divide Ratio Clock Rate 00 1 Input clock 01 2 Input clock ÷ 2 10 4 Input clock ÷ 4 11 8 Input clock ÷ 8 Table10-8. Conversion Modes MODE Mode Description 00 8-bit conversion (N=8) 01 12-bit conversion (N=12) 10 10-bit conversion (N=10) 11 Reserved Table10-9. Input Clock Select ADICLK Selected Clock Source 00 Bus clock 01 Bus clock divided by 2 10 Alternate clock (ALTCLK) 11 Asynchronous clock (ADACK) 10.3.8 Pin Control 1 Register (APCTL1) The pin control registers disable the I/O port control of MCU pins used as analog inputs. APCTL1 is used to control the pins associated with channels 0–7 of the ADC module. 7 6 5 4 3 2 1 0 R ADPC7 ADPC6 ADPC5 ADPC4 ADPC3 ADPC2 ADPC1 ADPC0 W Reset: 0 0 0 0 0 0 0 0 Figure10-10. Pin Control 1 Register (APCTL1) MC9S08JM60 Series Data Sheet, Rev. 5 144 Freescale Semiconductor

Analog-to-Digital Converter (S08ADC12V1) Table10-10. APCTL1 Register Field Descriptions Field Description 7 ADC Pin Control 7. ADPC7 controls the pin associated with channel AD7. ADPC7 0 AD7 pin I/O control enabled 1 AD7 pin I/O control disabled 6 ADC Pin Control 6. ADPC6 controls the pin associated with channel AD6. ADPC6 0 AD6 pin I/O control enabled 1 AD6 pin I/O control disabled 5 ADC Pin Control 5. ADPC5 controls the pin associated with channel AD5. ADPC5 0 AD5 pin I/O control enabled 1 AD5 pin I/O control disabled 4 ADC Pin Control 4. ADPC4 controls the pin associated with channel AD4. ADPC4 0 AD4 pin I/O control enabled 1 AD4 pin I/O control disabled 3 ADC Pin Control 3. ADPC3 controls the pin associated with channel AD3. ADPC3 0 AD3 pin I/O control enabled 1 AD3 pin I/O control disabled 2 ADC Pin Control 2. ADPC2 controls the pin associated with channel AD2. ADPC2 0 AD2 pin I/O control enabled 1 AD2 pin I/O control disabled 1 ADC Pin Control 1. ADPC1 controls the pin associated with channel AD1. ADPC1 0 AD1 pin I/O control enabled 1 AD1 pin I/O control disabled 0 ADC Pin Control 0. ADPC0 controls the pin associated with channel AD0. ADPC0 0 AD0 pin I/O control enabled 1 AD0 pin I/O control disabled 10.3.9 Pin Control 2 Register (APCTL2) APCTL2 controls channels 8–15 of the ADC module. 7 6 5 4 3 2 1 0 R ADPC15 ADPC14 ADPC13 ADPC12 ADPC11 ADPC10 ADPC9 ADPC8 W Reset: 0 0 0 0 0 0 0 0 Figure10-11. Pin Control 2 Register (APCTL2) MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 145

Analog-to-Digital Converter (S08ADC12V1) Table10-11. APCTL2 Register Field Descriptions Field Description 7 ADC Pin Control 15. ADPC15 controls the pin associated with channel AD15. ADPC15 0 AD15 pin I/O control enabled 1 AD15 pin I/O control disabled 6 ADC Pin Control 14. ADPC14 controls the pin associated with channel AD14. ADPC14 0 AD14 pin I/O control enabled 1 AD14 pin I/O control disabled 5 ADC Pin Control 13. ADPC13 controls the pin associated with channel AD13. ADPC13 0 AD13 pin I/O control enabled 1 AD13 pin I/O control disabled 4 ADC Pin Control 12. ADPC12 controls the pin associated with channel AD12. ADPC12 0 AD12 pin I/O control enabled 1 AD12 pin I/O control disabled 3 ADC Pin Control 11. ADPC11 controls the pin associated with channel AD11. ADPC11 0 AD11 pin I/O control enabled 1 AD11 pin I/O control disabled 2 ADC Pin Control 10. ADPC10 controls the pin associated with channel AD10. ADPC10 0 AD10 pin I/O control enabled 1 AD10 pin I/O control disabled 1 ADC Pin Control 9. ADPC9 controls the pin associated with channel AD9. ADPC9 0 AD9 pin I/O control enabled 1 AD9 pin I/O control disabled 0 ADC Pin Control 8. ADPC8 controls the pin associated with channel AD8. ADPC8 0 AD8 pin I/O control enabled 1 AD8 pin I/O control disabled 10.3.10 Pin Control 3 Register (APCTL3) APCTL3 controls channels 16–23 of the ADC module. 7 6 5 4 3 2 1 0 R ADPC23 ADPC22 ADPC21 ADPC20 ADPC19 ADPC18 ADPC17 ADPC16 W Reset: 0 0 0 0 0 0 0 0 Figure10-12. Pin Control 3 Register (APCTL3) MC9S08JM60 Series Data Sheet, Rev. 5 146 Freescale Semiconductor

Analog-to-Digital Converter (S08ADC12V1) Table10-12. APCTL3 Register Field Descriptions Field Description 7 ADC Pin Control 23. ADPC23 controls the pin associated with channel AD23. ADPC23 0 AD23 pin I/O control enabled 1 AD23 pin I/O control disabled 6 ADC Pin Control 22. ADPC22 controls the pin associated with channel AD22. ADPC22 0 AD22 pin I/O control enabled 1 AD22 pin I/O control disabled 5 ADC Pin Control 21. ADPC21 controls the pin associated with channel AD21. ADPC21 0 AD21 pin I/O control enabled 1 AD21 pin I/O control disabled 4 ADC Pin Control 20. ADPC20 controls the pin associated with channel AD20. ADPC20 0 AD20 pin I/O control enabled 1 AD20 pin I/O control disabled 3 ADC Pin Control 19. ADPC19 controls the pin associated with channel AD19. ADPC19 0 AD19 pin I/O control enabled 1 AD19 pin I/O control disabled 2 ADC Pin Control 18. ADPC18 controls the pin associated with channel AD18. ADPC18 0 AD18 pin I/O control enabled 1 AD18 pin I/O control disabled 1 ADC Pin Control 17. ADPC17 controls the pin associated with channel AD17. ADPC17 0 AD17 pin I/O control enabled 1 AD17 pin I/O control disabled 0 ADC Pin Control 16. ADPC16 controls the pin associated with channel AD16. ADPC16 0 AD16 pin I/O control enabled 1 AD16 pin I/O control disabled 10.4 Functional Description The ADC module is disabled during reset or when the ADCH bits are all high. The module is idle when a conversion has completed and another conversion has not been initiated. When idle, the module is in its lowest power state. The ADC can perform an analog-to-digital conversion on any of the software selectable channels. In 12-bit and 10-bit mode, the selected channel voltage is converted by a successive approximation algorithm into a 12-bit digital result. In 8-bit mode, the selected channel voltage is converted by a successive approximation algorithm into a 9-bit digital result. When the conversion is completed, the result is placed in the data registers (ADCRH and ADCRL). In 10-bit mode, the result is rounded to 10 bits and placed in the data registers (ADCRH and ADCRL). In 8-bit mode, the result is rounded to 8 bits and placed in ADCRL. The conversion complete flag (COCO) is then set and an interrupt is generated if the conversion complete interrupt has been enabled (AIEN = 1). The ADC module has the capability of automatically comparing the result of a conversion with the contents of its compare registers. The compare function is enabled by setting the ACFE bit and operates with any of the conversion modes and configurations. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 147

Analog-to-Digital Converter (S08ADC12V1) 10.4.1 Clock Select and Divide Control One of four clock sources can be selected as the clock source for the ADC module. This clock source is then divided by a configurable value to generate the input clock to the converter (ADCK). The clock is selected from one of the following sources by means of the ADICLK bits. • The bus clock, which is equal to the frequency at which software is executed. This is the default selection following reset. • The bus clock divided by two. For higher bus clock rates, this allows a maximum divide by 16 of the bus clock. • ALTCLK, as defined for this MCU (See module section introduction). • The asynchronous clock (ADACK). This clock is generated from a clock source within the ADC module. When selected as the clock source, this clock remains active while the MCU is in wait or stop3 mode and allows conversions in these modes for lower noise operation. Whichever clock is selected, its frequency must fall within the specified frequency range for ADCK. If the available clocks are too slow, the ADC do not perform according to specifications. If the available clocks are too fast, the clock must be divided to the appropriate frequency. This divider is specified by the ADIV bits and can be divide-by 1, 2, 4, or 8. 10.4.2 Input Select and Pin Control The pin control registers (APCTL3, APCTL2, and APCTL1) disable the I/O port control of the pins used as analog inputs.When a pin control register bit is set, the following conditions are forced for the associated MCU pin: • The output buffer is forced to its high impedance state. • The input buffer is disabled. A read of the I/O port returns a zero for any pin with its input buffer disabled. • The pullup is disabled. 10.4.3 Hardware Trigger The ADC module has a selectable asynchronous hardware conversion trigger, ADHWT, that is enabled when the ADTRG bit is set. This source is not available on all MCUs. Consult the module introduction for information on the ADHWT source specific to this MCU. When ADHWT source is available and hardware trigger is enabled (ADTRG=1), a conversion is initiated on the rising edge of ADHWT. If a conversion is in progress when a rising edge occurs, the rising edge is ignored. In continuous convert configuration, only the initial rising edge to launch continuous conversions is observed. The hardware trigger function operates in conjunction with any of the conversion modes and configurations. 10.4.4 Conversion Control Conversions can be performed in 12-bit mode, 10-bit mode, or 8-bit mode as determined by the MODE bits. Conversions can be initiated by a software or hardware trigger. In addition, the ADC module can be MC9S08JM60 Series Data Sheet, Rev. 5 148 Freescale Semiconductor

Analog-to-Digital Converter (S08ADC12V1) configured for low power operation, long sample time, continuous conversion, and automatic compare of the conversion result to a software determined compare value. 10.4.4.1 Initiating Conversions A conversion is initiated: • Following a write to ADCSC1 (with ADCH bits not all 1s) if software triggered operation is selected. • Following a hardware trigger (ADHWT) event if hardware triggered operation is selected. • Following the transfer of the result to the data registers when continuous conversion is enabled. If continuous conversions are enabled, a new conversion is automatically initiated after the completion of the current conversion. In software triggered operation, continuous conversions begin after ADCSC1 is written and continue until aborted. In hardware triggered operation, continuous conversions begin after a hardware trigger event and continue until aborted. 10.4.4.2 Completing Conversions A conversion is completed when the result of the conversion is transferred into the data result registers, ADCRH and ADCRL. This is indicated by the setting of COCO. An interrupt is generated if AIEN is high at the time that COCO is set. A blocking mechanism prevents a new result from overwriting previous data in ADCRH and ADCRL if the previous data is in the process of being read while in 12-bit or 10-bit MODE (the ADCRH register has been read but the ADCRL register has not). When blocking is active, the data transfer is blocked, COCO is not set, and the new result is lost. In the case of single conversions with the compare function enabled and the compare condition false, blocking has no effect and ADC operation is terminated. In all other cases of operation, when a data transfer is blocked, another conversion is initiated regardless of the state of ADCO (single or continuous conversions enabled). If single conversions are enabled, the blocking mechanism could result in several discarded conversions and excess power consumption. To avoid this issue, the data registers must not be read after initiating a single conversion until the conversion completes. 10.4.4.3 Aborting Conversions Any conversion in progress is aborted when: • A write to ADCSC1 occurs (the current conversion will be aborted and a new conversion will be initiated, if ADCH are not all 1s). • A write to ADCSC2, ADCCFG, ADCCVH, or ADCCVL occurs. This indicates a mode of operation change has occurred and the current conversion is therefore invalid. • The MCU is reset. • The MCU enters stop mode with ADACK not enabled. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 149

Analog-to-Digital Converter (S08ADC12V1) When a conversion is aborted, the contents of the data registers, ADCRH and ADCRL, are not altered. However, they continue to be the values transferred after the completion of the last successful conversion. If the conversion was aborted by a reset, ADCRH and ADCRL return to their reset states. 10.4.4.4 Power Control The ADC module remains in its idle state until a conversion is initiated. If ADACK is selected as the conversion clock source, the ADACK clock generator is also enabled. Power consumption when active can be reduced by setting ADLPC. This results in a lower maximum value for f (see the electrical specifications). ADCK 10.4.4.5 Sample Time and Total Conversion Time The total conversion time depends on the sample time (as determined by ADLSMP), the MCU bus frequency, the conversion mode (8-bit, 10-bit or 12-bit), and the frequency of the conversion clock (f ). ADCK After the module becomes active, sampling of the input begins. ADLSMP selects between short (3.5 ADCK cycles) and long (23.5 ADCK cycles) sample times.When sampling is complete, the converter is isolated from the input channel and a successive approximation algorithm is performed to determine the digital value of the analog signal. The result of the conversion is transferred to ADCRH and ADCRL upon completion of the conversion algorithm. If the bus frequency is less than the f frequency, precise sample time for continuous conversions ADCK cannot be guaranteed when short sample is enabled (ADLSMP=0). If the bus frequency is less than 1/11th of the f frequency, precise sample time for continuous conversions cannot be guaranteed when long ADCK sample is enabled (ADLSMP=1). The maximum total conversion time for different conditions is summarized in Table 10-13. Table10-13. Total Conversion Time vs. Control Conditions Conversion Type ADICLK ADLSMP Max Total Conversion Time Single or first continuous 8-bit 0x, 10 0 20 ADCK cycles + 5 bus clock cycles Single or first continuous 10-bit or 12-bit 0x, 10 0 23 ADCK cycles + 5 bus clock cycles Single or first continuous 8-bit 0x, 10 1 40 ADCK cycles + 5 bus clock cycles Single or first continuous 10-bit or 12-bit 0x, 10 1 43 ADCK cycles + 5 bus clock cycles Single or first continuous 8-bit 11 0 5 μs + 20 ADCK + 5 bus clock cycles Single or first continuous 10-bit or 12-bit 11 0 5 μs + 23 ADCK + 5 bus clock cycles Single or first continuous 8-bit 11 1 5 μs + 40 ADCK + 5 bus clock cycles Single or first continuous 10-bit or 12-bit 11 1 5 μs + 43 ADCK + 5 bus clock cycles Subsequent continuous 8-bit; xx 0 17 ADCK cycles f > f BUS ADCK Subsequent continuous 10-bit or 12-bit; xx 0 20 ADCK cycles f > f BUS ADCK Subsequent continuous 8-bit; xx 1 37 ADCK cycles f > f /11 BUS ADCK Subsequent continuous 10-bit or 12-bit; xx 1 40 ADCK cycles f > f /11 BUS ADCK MC9S08JM60 Series Data Sheet, Rev. 5 150 Freescale Semiconductor

Analog-to-Digital Converter (S08ADC12V1) The maximum total conversion time is determined by the clock source chosen and the divide ratio selected. The clock source is selectable by the ADICLK bits, and the divide ratio is specified by the ADIV bits. For example, in 10-bit mode, with the bus clock selected as the input clock source, the input clock divide-by-1 ratio selected, and a bus frequency of 8 MHz, then the conversion time for a single conversion is: 23 ADCK Cyc 5 bus Cyc Conversion time = + = 3.5 μs 8 MHz/1 8 MHz Number of bus cycles = 3.5 μs x 8 MHz = 28 cycles NOTE The ADCK frequency must be between f minimum and f ADCK ADCK maximum to meet ADC specifications. 10.4.5 Automatic Compare Function The compare function can be configured to check for an upper or lower limit. After the input is sampled and converted, the result is added to the two’s complement of the compare value (ADCCVH and ADCCVL). When comparing to an upper limit (ACFGT = 1), if the result is greater-than or equal-to the compare value, COCO is set. When comparing to a lower limit (ACFGT = 0), if the result is less than the compare value, COCO is set. The value generated by the addition of the conversion result and the two’s complement of the compare value is transferred to ADCRH and ADCRL. Upon completion of a conversion while the compare function is enabled, if the compare condition is not true, COCO is not set and no data is transferred to the result registers. An ADC interrupt is generated upon the setting of COCO if the ADC interrupt is enabled (AIEN = 1). NOTE The compare function can monitor the voltage on a channel while the MCU is in wait or stop3 mode. The ADC interrupt wakes the MCU when the compare condition is met. 10.4.6 MCU Wait Mode Operation Wait mode is a lower power-consumption standby mode from which recovery is fast because the clock sources remain active. If a conversion is in progress when the MCU enters wait mode, it continues until completion. Conversions can be initiated while the MCU is in wait mode by means of the hardware trigger or if continuous conversions are enabled. The bus clock, bus clock divided by two, and ADACK are available as conversion clock sources while in wait mode. The use of ALTCLK as the conversion clock source in wait is dependent on the definition of ALTCLK for this MCU. Consult the module introduction for information on ALTCLK specific to this MCU. A conversion complete event sets the COCO and generates an ADC interrupt to wake the MCU from wait mode if the ADC interrupt is enabled (AIEN = 1). MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 151

Analog-to-Digital Converter (S08ADC12V1) 10.4.7 MCU Stop3 Mode Operation Stop mode is a low power-consumption standby mode during which most or all clock sources on the MCU are disabled. 10.4.7.1 Stop3 Mode With ADACK Disabled If the asynchronous clock, ADACK, is not selected as the conversion clock, executing a stop instruction aborts the current conversion and places the ADC in its idle state. The contents of ADCRH and ADCRL are unaffected by stop3 mode. After exiting from stop3 mode, a software or hardware trigger is required to resume conversions. 10.4.7.2 Stop3 Mode With ADACK Enabled If ADACK is selected as the conversion clock, the ADC continues operation during stop3 mode. For guaranteed ADC operation, the MCU’s voltage regulator must remain active during stop3 mode. Consult the module introduction for configuration information for this MCU. If a conversion is in progress when the MCU enters stop3 mode, it continues until completion. Conversions can be initiated while the MCU is in stop3 mode by means of the hardware trigger or if continuous conversions are enabled. A conversion complete event sets the COCO and generates an ADC interrupt to wake the MCU from stop3 mode if the ADC interrupt is enabled (AIEN = 1). NOTE The ADC module can wake the system from low-power stop and cause the MCU to begin consuming run-level currents without generating a system level interrupt. To prevent this scenario, software should ensure the data transfer blocking mechanism (discussed in Section10.4.4.2, “Completing Conversions,”) is cleared when entering stop3 and continuing ADC conversions. 10.4.8 MCU Stop2 Mode Operation The ADC module is automatically disabled when the MCU enters stop2 mode. All module registers contain their reset values following exit from stop2. Therefore, the module must be re-enabled and re-configured following exit from stop2. 10.5 Initialization Information This section gives an example that provides some basic direction on how to initialize and configure the ADC module. You can configure the module for 8-, 10-, or 12-bit resolution, single or continuous conversion, and a polled or interrupt approach, among many other options. Refer to Table 10-7, Table 10-8, and Table 10-9 for information used in this example. MC9S08JM60 Series Data Sheet, Rev. 5 152 Freescale Semiconductor

Analog-to-Digital Converter (S08ADC12V1) NOTE Hexadecimal values designated by a preceding 0x, binary values designated by a preceding %, and decimal values have no preceding character. 10.5.1 ADC Module Initialization Example 10.5.1.1 Initialization Sequence Before the ADC module can be used to complete conversions, an initialization procedure must be performed. A typical sequence is as follows: 1. Update the configuration register (ADCCFG) to select the input clock source and the divide ratio used to generate the internal clock, ADCK. This register is also used for selecting sample time and low-power configuration. 2. Update status and control register 2 (ADCSC2) to select the conversion trigger (hardware or software) and compare function options, if enabled. 3. Update status and control register 1 (ADCSC1) to select whether conversions will be continuous or completed only once, and to enable or disable conversion complete interrupts. The input channel on which conversions will be performed is also selected here. 10.5.1.2 Pseudo-Code Example In this example, the ADC module is set up with interrupts enabled to perform a single 10-bit conversion at low power with a long sample time on input channel 1, where the internal ADCK clock is derived from the bus clock divided by 1. ADCCFG = 0x98 (%10011000) Bit 7 ADLPC 1 Configures for low power (lowers maximum clock speed) Bit 6:5 ADIV 00 Sets the ADCK to the input clock ÷ 1 Bit 4 ADLSMP 1 Configures for long sample time Bit 3:2 MODE 10 Sets mode at 10-bit conversions Bit 1:0 ADICLK 00 Selects bus clock as input clock source ADCSC2 = 0x00 (%00000000) Bit 7 ADACT 0 Flag indicates if a conversion is in progress Bit 6 ADTRG 0 Software trigger selected Bit 5 ACFE 0 Compare function disabled Bit 4 ACFGT 0 Not used in this example Bit 3:2 00 Reserved, always reads zero Bit 1:0 00 Reserved for Freescale’s internal use; always write zero ADCSC1 = 0x41 (%01000001) Bit 7 COCO 0 Read-only flag which is set when a conversion completes Bit 6 AIEN 1 Conversion complete interrupt enabled Bit 5 ADCO 0 One conversion only (continuous conversions disabled) Bit 4:0 ADCH 00001 Input channel 1 selected as ADC input channel ADCRH/L = 0xxx Holds results of conversion. Read high byte (ADCRH) before low byte (ADCRL) so that conversion data cannot be overwritten with data from the next conversion. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 153

Analog-to-Digital Converter (S08ADC12V1) ADCCVH/L = 0xxx Holds compare value when compare function enabled APCTL1=0x02 AD1 pin I/O control disabled. All other AD pins remain general purpose I/O pins APCTL2=0x00 All other AD pins remain general purpose I/O pins Reset Initialize ADC ADCCFG = 0x98 ADCSC2 = 0x00 ADCSC1 = 0x41 Check No COCO=1? Yes Read ADCRH Then ADCRL To Clear COCO Bit Continue Figure10-13. Initialization Flowchart for Example 10.6 Application Information This section contains information for using the ADC module in applications. The ADC has been designed to be integrated into a microcontroller for use in embedded control applications requiring an A/D converter. 10.6.1 External Pins and Routing The following sections discuss the external pins associated with the ADC module and how they should be used for best results. MC9S08JM60 Series Data Sheet, Rev. 5 154 Freescale Semiconductor

Analog-to-Digital Converter (S08ADC12V1) 10.6.1.1 Analog Supply Pins The ADC module has analog power and ground supplies (V and V ) available as separate pins DDAD SSAD on some devices. V is shared on the same pin as the MCU digital V on some devices.On other SSAD SS devices, V and V are shared with the MCU digital supply pins. In these cases, there are separate SSAD DDAD pads for the analog supplies bonded to the same pin as the corresponding digital supply so that some degree of isolation between the supplies is maintained. When available on a separate pin, both V and V must be connected to the same voltage potential DDAD SSAD as their corresponding MCU digital supply (V and V ) and must be routed carefully for maximum DD SS noise immunity and bypass capacitors placed as near as possible to the package. If separate power supplies are used for analog and digital power, the ground connection between these supplies must be at the V pin. This should be the only ground connection between these supplies if SSAD possible. The V pin makes a good single point ground location. SSAD 10.6.1.2 Analog Reference Pins In addition to the analog supplies, the ADC module has connections for two reference voltage inputs. The high reference is V , which may be shared on the same pin as V on some devices. The low REFH DDAD reference is V , which may be shared on the same pin as V on some devices. REFL SSAD When available on a separate pin, V may be connected to the same potential as V , or may be REFH DDAD driven by an external source between the minimum V spec and the V potential (V must DDAD DDAD REFH never exceed V ). When available on a separate pin, V must be connected to the same voltage DDAD REFL potential as V . V and V must be routed carefully for maximum noise immunity and bypass SSAD REFH REFL capacitors placed as near as possible to the package. AC current in the form of current spikes required to supply charge to the capacitor array at each successive approximation step is drawn through the V and V loop. The best external component to meet this REFH REFL current demand is a 0.1 μF capacitor with good high frequency characteristics. This capacitor is connected between V and V and must be placed as near as possible to the package pins. Resistance in the REFH REFL path is not recommended because the current causes a voltage drop that could result in conversion errors. Inductance in this path must be minimum (parasitic only). 10.6.1.3 Analog Input Pins The external analog inputs are typically shared with digital I/O pins on MCU devices. The pin I/O control is disabled by setting the appropriate control bit in one of the pin control registers. Conversions can be performed on inputs without the associated pin control register bit set. It is recommended that the pin control register bit always be set when using a pin as an analog input. This avoids problems with contention because the output buffer is in its high impedance state and the pullup is disabled. Also, the input buffer draws DC current when its input is not at V or V . Setting the pin control register bits for all pins used DD SS as analog inputs should be done to achieve lowest operating current. Empirical data shows that capacitors on the analog inputs improve performance in the presence of noise or when the source impedance is high. Use of 0.01 μF capacitors with good high-frequency characteristics is sufficient. These capacitors are not necessary in all cases, but when used they must be placed as near as possible to the package pins and be referenced to V . SSA MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 155

Analog-to-Digital Converter (S08ADC12V1) For proper conversion, the input voltage must fall between V and V . If the input is equal to or REFH REFL exceeds V , the converter circuit converts the signal to 0xFFF (full scale 12-bit representation), 0x3FF REFH (full scale 10-bit representation) or 0xFF (full scale 8-bit representation). If the input is equal to or less than V ,the converter circuit converts it to 0x000. Input voltages between V and V are REFL REFH REFL straight-line linear conversions. There is a brief current associated with V when the sampling REFL capacitor is charging. The input is sampled for 3.5cycles of the ADCK source when ADLSMP is low, or 23.5cycles when ADLSMP is high. For minimal loss of accuracy due to current injection, pins adjacent to the analog input pins should not be transitioning during conversions. 10.6.2 Sources of Error Several sources of error exist for A/D conversions. These are discussed in the following sections. 10.6.2.1 Sampling Error For proper conversions, the input must be sampled long enough to achieve the proper accuracy. Given the maximum input resistance of approximately 7kΩ and input capacitance of approximately 5.5pF, sampling to within 1/4LSB (at 12-bit resolution) can be achieved within the minimum sample window (3.5cycles @ 8MHz maximum ADCK frequency) provided the resistance of the external analog source (R ) is kept AS below 2kΩ. Higher source resistances or higher-accuracy sampling is possible by setting ADLSMP (to increase the sample window to 23.5 cycles) or decreasing ADCK frequency to increase sample time. 10.6.2.2 Pin Leakage Error Leakage on the I/O pins can cause conversion error if the external analog source resistance (R ) is high. AS If this error cannot be tolerated by the application, keep R lower than V / (2N*I ) for less than AS DDAD LEAK 1/4LSB leakage error (N = 8 in 8-bit, 10 in 10-bit or 12 in 12-bit mode). 10.6.2.3 Noise-Induced Errors System noise that occurs during the sample or conversion process can affect the accuracy of the conversion. The ADC accuracy numbers are guaranteed as specified only if the following conditions are met: • There is a 0.1μF low-ESR capacitor from V to V . REFH REFL • There is a 0.1μF low-ESR capacitor from V to V . DDAD SSAD • If inductive isolation is used from the primary supply, an additional 1 μF capacitor is placed from V to V . DDAD SSAD • V (and V , if connected) is connected to V at a quiet point in the ground plane. SSAD REFL SS • Operate the MCU in wait or stop3 mode before initiating (hardware triggered conversions) or immediately after initiating (hardware or software triggered conversions) the ADC conversion. — For software triggered conversions, immediately follow the write to ADCSC1 with a wait instruction or stop instruction. MC9S08JM60 Series Data Sheet, Rev. 5 156 Freescale Semiconductor

Analog-to-Digital Converter (S08ADC12V1) — For stop3 mode operation, select ADACK as the clock source. Operation in stop3 reduces V DD noise but increases effective conversion time due to stop recovery. • There is no I/O switching, input or output, on the MCU during the conversion. There are some situations where external system activity causes radiated or conducted noise emissions or excessive V noise is coupled into the ADC. In these situations, or when the MCU cannot be placed in DD wait or stop3 or I/O activity cannot be halted, these recommended actions may reduce the effect of noise on the accuracy: • Place a 0.01μF capacitor (C ) on the selected input channel to V or V (this improves AS REFL SSAD noise issues, but affects the sample rate based on the external analog source resistance). • Average the result by converting the analog input many times in succession and dividing the sum of the results. Four samples are required to eliminate the effect of a 1LSB, one-time error. • Reduce the effect of synchronous noise by operating off the asynchronous clock (ADACK) and averaging. Noise that is synchronous to ADCK cannot be averaged out. 10.6.2.4 Code Width and Quantization Error The ADC quantizes the ideal straight-line transfer function into 4096 steps (in 12-bit mode). Each step ideally has the same height (1 code) and width. The width is defined as the delta between the transition points to one code and the next. The ideal code width for an N bit converter (in this case N can be 8, 10 or 12), defined as 1LSB, is: 1 lsb = (V - V ) / 2N Eqn.10-2 REFH REFL There is an inherent quantization error due to the digitization of the result. For 8-bit or 10-bit conversions the code transitions when the voltage is at the midpoint between the points where the straight line transfer function is exactly represented by the actual transfer function. Therefore, the quantization error will be ± 1/2 lsb in 8- or 10-bit mode. As a consequence, however, the code width of the first (0x000) conversion is only 1/2 lsb and the code width of the last (0xFF or 0x3FF) is 1.5 lsb. For 12-bit conversions the code transitions only after the full code width is present, so the quantization error is −1 lsb to 0 lsb and the code width of each step is 1 lsb. 10.6.2.5 Linearity Errors The ADC may also exhibit non-linearity of several forms. Every effort has been made to reduce these errors but the system should be aware of them because they affect overall accuracy. These errors are: • Zero-scale error (E ) (sometimes called offset) — This error is defined as the difference between ZS the actual code width of the first conversion and the ideal code width (1/2 lsb in 8-bit or 10-bit modes and 1 lsb in 12-bit mode). If the first conversion is 0x001, the difference between the actual 0x001 code width and its ideal (1 lsb) is used. • Full-scale error (E ) — This error is defined as the difference between the actual code width of FS the last conversion and the ideal code width (1.5 lsb in 8-bit or 10-bit modes and 1LSB in 12-bit mode). If the last conversion is 0x3FE, the difference between the actual 0x3FE code width and its ideal (1LSB) is used. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 157

Analog-to-Digital Converter (S08ADC12V1) • Differential non-linearity (DNL) — This error is defined as the worst-case difference between the actual code width and the ideal code width for all conversions. • Integral non-linearity (INL) — This error is defined as the highest-value the (absolute value of the) running sum of DNL achieves. More simply, this is the worst-case difference of the actual transition voltage to a given code and its corresponding ideal transition voltage, for all codes. • Total unadjusted error (TUE) — This error is defined as the difference between the actual transfer function and the ideal straight-line transfer function and includes all forms of error. 10.6.2.6 Code Jitter, Non-Monotonicity, and Missing Codes Analog-to-digital converters are susceptible to three special forms of error. These are code jitter, non-monotonicity, and missing codes. Code jitter is when, at certain points, a given input voltage converts to one of two values when sampled repeatedly. Ideally, when the input voltage is infinitesimally smaller than the transition voltage, the converter yields the lower code (and vice-versa). However, even small amounts of system noise can cause the converter to be indeterminate (between two codes) for a range of input voltages around the transition voltage. This range is normally around ±1/2 lsb in 8-bit or 10-bit mode, or around 2 lsb in 12-bit mode, and increases with noise. This error may be reduced by repeatedly sampling the input and averaging the result. Additionally the techniques discussed in Section10.6.2.3 reduces this error. Non-monotonicity is defined as when, except for code jitter, the converter converts to a lower code for a higher input voltage. Missing codes are those values never converted for any input value. In 8-bit or 10-bit mode, the ADC is guaranteed to be monotonic and have no missing codes. MC9S08JM60 Series Data Sheet, Rev. 5 158 Freescale Semiconductor

Chapter 11 Inter-Integrated Circuit (S08IICV2) 11.1 Introduction The MC9S08JM60 series of microcontrollers has an inter-integrated circuit (IIC) module for communication with other integrated circuits. The two pins associated with this module, SCL and SDA, are shared with PTC0 and PTC1, respectively. NOTE MC9S08JM60 series devices operate at a higher voltage range (2.7 V to 5.5V) and do not include stop1 mode. Therefore, please disregard references to stop1. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 159

Chapter11 Inter-Integrated Circuit (S08IICV2) USBDP ON-CHIP ICE AND USBDN HCS08 CORE DEBUG MODULE (DBG) A T 6 R PTA5– PTA0 O USB SIE P BKGD/MS FULL SPEED PTB7/ADP7 BDC CPU USB PTB6/ADP6 USB ENDPOINT TRANSCEIVER PTB5/KBIP5/ADP5 RAM B T PTB4/KBIP4/ADP4 SSPSS2CK2 POR PTB3/SS2/ADP3 RESET HCS08 SYSTEM CONTROL 8-/16-BIT SERIAL PERIPHERAL MOSI2 PTB2/SPSCK2/ADP2 INTERFACE MODULE (SPI2) PTB1/MOSI2/ADP1 MISO2 PTB0/MISO2/ADP0 RESETS AND INTERRUPTS MODES OF OPERATION PTC6 IRQ/TPMCLK POWER MANAGEMENT SERIAL COMMUNICATIONS RxD2 PTC5/RxD2 COP IRQ LVD INTERFACE MODULE (SCI2) TxD2 ORT C PPTTCC34/TxD2 P PTC2 SDA PTC1/SDA IIC MODULE (IIC) SCL PTC0/SCL VDDAD 12-CHANNEL, 12-BIT 8 PTD7 VSSAD ANALOG-TO-DIGITAL 4 PTD6 VREFL CONVERTER (ADC) PTD5 VREFH D PTD4/ADP11 T R PTD3/KBIP3/ADP10 O USER Flash (IN BYTES) P PTD2/KBIP2/ACMPO ACMP– MC9S08JM60 = 60,912 PTD1/ADP9/ACMP– MC9S08JM32 = 32,768 ANALOG COMPARATOR ACMP+ PTD0/ADP8/ACMP+ (ACMP) ACMPO SS1 PTE7/SS1 USER RAM (IN BYTES) SPSCK1 8-/16-BIT SERIAL PERIPHERAL PTE6/SPSCK1 MMCC99SS0088JJMM6302 == 42009468 INTERFACE MODULE (SPI1) MOSI1 PTE5/MOSI1 MISO1 PTE4/MISO1 TPMCLK E MULTI-PURPOSE CLOCK 6-CHMAONDNUELLE T (ITMPEMR1/P)WM TTPPMM11CCHH10 PORT PTE3/TPM1CH1 GENERATOR (MCG) PTE2/TPM1CH0 TPM1CHx4 RxD1 SERIAL COMMUNICATIONS PTE1/RxD1 VSSOSC LOW-POWER OSCILLATOR TxD1 PTE0/TxD1 INTERFACE MODULE (SCI1) PTF7 VDD SYSTEM TPMCLK PTF6 VSS RVEOGLUTLAAGTEO R 2-CHMAONDNUELLE T (ITMPEMR2/P)WM TTPPMM22CCHH10 T F PPTTFF54//TTPPMM22CCHH10 OR PTF3/TPM1CH5 KBIPx P PTF2/TPM1CH4 VUSB33 USB 3.3-V VOLTAGE REGULATOR 8-BIT KEYBOARD 4 PTF1/TPM1CH3 INTERRUPT MODULE (KBI) KBIPx 4 PTF0/TPM1CH2 REAL-TIME COUNTER (RTC) EXTAL PTG5/EXTAL XTAL NOTES: G PTG4/XTAL 1. Port pins are software configurable with pullup device if input port. RT PTG3/KBIP7 O PTG2/KBIP6 2. Pin contains software configurable pullup/pull-down device if IRQ is enabled P PTG1/KBIP1 (IRQPE=1). Pull-down is enabled if rising edge detect is selected (IRQEDG=1) PTG0/KBIP0 3. IRQ does not have a clamp diode to V . IRQ must not be driven above V . DD DD 4. Pin contains integrated pullup device. 5. When pin functions as KBI (KBIPEn = 1) and associated pin is configured to enable the pullup device, KBEDGn can be used to reconfigure the pull-up as a pull-down device. Figure11-1. MC9S08JM60 Series Block Diagram Highlighting the IIC Block and Pins MC9S08JM60 Series Data Sheet, Rev. 5 160 Freescale Semiconductor

11.1.1 Features The IIC includes these distinctive features: • Compatible with IIC bus standard • Multi-master operation • Software programmable for one of 64 different serial clock frequencies • Software selectable acknowledge bit • Interrupt driven byte-by-byte data transfer • Arbitration lost interrupt with automatic mode switching from master to slave • Calling address identification interrupt • Start and stop signal generation/detection • Repeated start signal generation • Acknowledge bit generation/detection • Bus busy detection • General call recognition • 10-bit address extension 11.1.2 Modes of Operation A brief description of the IIC in the various MCU modes is given here. • Run mode — This is the basic mode of operation. To conserve power in this mode, disable the module. • Wait mode — The module continues to operate while the MCU is in wait mode and can provide a wake-up interrupt. • Stop mode — The IIC is inactive in stop3 mode for reduced power consumption. The stop instruction does not affect IIC register states. Stop2 resets the register contents. 11.1.3 Block Diagram Figure 11-2 is a block diagram of the IIC. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 161

Address Data Bus Interrupt ADDR_DECODE DATA_MUX CTRL_REG FREQ_REG ADDR_REG STATUS_REG DATA_REG Input Sync In/Out Start Data Stop Shift Arbitration Register Control Clock Control Address Compare SCL SDA Figure11-2. IIC Functional Block Diagram 11.2 External Signal Description This section describes each user-accessible pin signal. 11.2.1 SCL — Serial Clock Line The bidirectional SCL is the serial clock line of the IIC system. 11.2.2 SDA — Serial Data Line The bidirectional SDA is the serial data line of the IIC system. 11.3 Register Definition This section consists of the IIC register descriptions in address order. Refer to the direct-page register summary in the memory chapter of this document for the absolute address assignments for all IIC registers. This section refers to registers and control bits only by their names. A MC9S08JM60 Series Data Sheet, Rev. 5 162 Freescale Semiconductor

Freescale-provided equate or header file is used to translate these names into the appropriate absolute addresses. 11.3.1 IIC Address Register (IICA) 7 6 5 4 3 2 1 0 R 0 AD7 AD6 AD5 AD4 AD3 AD2 AD1 W Reset 0 0 0 0 0 0 0 0 = Unimplemented or Reserved Figure11-3. IIC Address Register (IICA) Table11-1. IICA Field Descriptions Field Description 7–1 Slave Address. The AD[7:1] field contains the slave address to be used by the IIC module. This field is used on AD[7:1] the 7-bit address scheme and the lower seven bits of the 10-bit address scheme. 11.3.2 IIC Frequency Divider Register (IICF) 7 6 5 4 3 2 1 0 R MULT ICR W Reset 0 0 0 0 0 0 0 0 Figure11-4. IIC Frequency Divider Register (IICF) MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 163

Table11-2. IICF Field Descriptions Field Description 7–6 IIC Multiplier Factor. The MULT bits define the multiplier factor, mul. This factor, along with the SCL divider, MULT generates the IIC baud rate. The multiplier factor mul as defined by the MULT bits is provided below. 00 mul = 01 01 mul = 02 10 mul = 04 11 Reserved 5–0 IIC Clock Rate. The ICR bits are used to prescale the bus clock for bit rate selection. These bits and the MULT ICR bits determine the IIC baud rate, the SDA hold time, the SCL Start hold time, and the SCL Stop hold time. Table11-4 provides the SCL divider and hold values for corresponding values of the ICR. The SCL divider multiplied by multiplier factor mul generates IIC baud rate. bus speed (Hz) IIC baud rate = --------------------------------------------- Eqn.11-1 mul×SCLdivider SDA hold time is the delay from the falling edge of SCL (IIC clock) to the changing of SDA (IIC data). SDA hold time = bus period (s) × mul × SDA hold value Eqn.11-2 SCL start hold time is the delay from the falling edge of SDA (IIC data) while SCL is high (Start condition) to the falling edge of SCL (IIC clock). SCL Start hold time = bus period (s) × mul × SCL Start hold value Eqn.11-3 SCL stop hold time is the delay from the rising edge of SCL (IIC clock) to the rising edge of SDA SDA (IIC data) while SCL is high (Stop condition). SCL Stop hold time = bus period (s) × mul × SCL Stop hold value Eqn.11-4 For example, if the bus speed is 8MHz, the table below shows the possible hold time values with different ICR and MULT selections to achieve an IIC baud rate of 100kbps. Table11-3. Hold Time Values for 8 MHz Bus Speed Hold Times (μs) MULT ICR SDA SCL Start SCL Stop 0x2 0x00 3.500 3.000 5.500 0x1 0x07 2.500 4.000 5.250 0x1 0x0B 2.250 4.000 5.250 0x0 0x14 2.125 4.250 5.125 0x0 0x18 1.125 4.750 5.125 MC9S08JM60 Series Data Sheet, Rev. 5 164 Freescale Semiconductor

Table11-4. IIC Divider and Hold Values SCL Hold SCL Hold SDA SCL Hold SCL Hold ICR SCL SDA Hold ICR SCL (Start) (Stop) Hold (Start) (Stop) (hex) Divider Value (hex) Divider Value Value Value Value Value 00 20 7 6 11 20 160 17 78 81 01 22 7 7 12 21 192 17 94 97 02 24 8 8 13 22 224 33 110 113 03 26 8 9 14 23 256 33 126 129 04 28 9 10 15 24 288 49 142 145 05 30 9 11 16 25 320 49 158 161 06 34 10 13 18 26 384 65 190 193 07 40 10 16 21 27 480 65 238 241 08 28 7 10 15 28 320 33 158 161 09 32 7 12 17 29 384 33 190 193 0A 36 9 14 19 2A 448 65 222 225 0B 40 9 16 21 2B 512 65 254 257 0C 44 11 18 23 2C 576 97 286 289 0D 48 11 20 25 2D 640 97 318 321 0E 56 13 24 29 2E 768 129 382 385 0F 68 13 30 35 2F 960 129 478 481 10 48 9 18 25 30 640 65 318 321 11 56 9 22 29 31 768 65 382 385 12 64 13 26 33 32 896 129 446 449 13 72 13 30 37 33 1024 129 510 513 14 80 17 34 41 34 1152 193 574 577 15 88 17 38 45 35 1280 193 638 641 16 104 21 46 53 36 1536 257 766 769 17 128 21 58 65 37 1920 257 958 961 18 80 9 38 41 38 1280 129 638 641 19 96 9 46 49 39 1536 129 766 769 1A 112 17 54 57 3A 1792 257 894 897 1B 128 17 62 65 3B 2048 257 1022 1025 1C 144 25 70 73 3C 2304 385 1150 1153 1D 160 25 78 81 3D 2560 385 1278 1281 1E 192 33 94 97 3E 3072 513 1534 1537 1F 240 33 118 121 3F 3840 513 1918 1921 MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 165

11.3.3 IIC Control Register (IICC1) 7 6 5 4 3 2 1 0 R 0 0 0 IICEN IICIE MST TX TXAK W RSTA Reset 0 0 0 0 0 0 0 0 = Unimplemented or Reserved Figure11-5. IIC Control Register (IICC1) Table11-5. IICC1 Field Descriptions Field Description 7 IIC Enable. The IICEN bit determines whether the IIC module is enabled. IICEN 0 IIC is not enabled 1 IIC is enabled 6 IIC Interrupt Enable. The IICIE bit determines whether an IIC interrupt is requested. IICIE 0 IIC interrupt request not enabled 1 IIC interrupt request enabled 5 Master Mode Select. The MST bit changes from a 0 to a 1 when a start signal is generated on the bus and MST master mode is selected. When this bit changes from a 1 to a 0 a stop signal is generated and the mode of operation changes from master to slave. 0 Slave mode 1 Master mode 4 Transmit Mode Select. The TX bit selects the direction of master and slave transfers. In master mode, this bit TX should be set according to the type of transfer required. Therefore, for address cycles, this bit is always high. When addressed as a slave, this bit should be set by software according to the SRW bit in the status register. 0 Receive 1 Transmit 3 Transmit Acknowledge Enable. This bit specifies the value driven onto the SDA during data acknowledge TXAK cycles for master and slave receivers. 0 An acknowledge signal is sent out to the bus after receiving one data byte 1 No acknowledge signal response is sent 2 Repeat start. Writing a 1 to this bit generates a repeated start condition provided it is the current master. This RSTA bit is always read as cleared. Attempting a repeat at the wrong time results in loss of arbitration. 11.3.4 IIC Status Register (IICS) 7 6 5 4 3 2 1 0 R TCF BUSY 0 SRW RXAK IAAS ARBL IICIF W Reset 1 0 0 0 0 0 0 0 = Unimplemented or Reserved Figure11-6. IIC Status Register (IICS) MC9S08JM60 Series Data Sheet, Rev. 5 166 Freescale Semiconductor

Table11-6. IICS Field Descriptions Field Description 7 Transfer Complete Flag. This bit is set on the completion of a byte transfer. This bit is only valid during or TCF immediately following a transfer to the IIC module or from the IIC module.The TCF bit is cleared by reading the IICD register in receive mode or writing to the IICD in transmit mode. 0 Transfer in progress 1 Transfer complete 6 Addressed as a Slave. The IAAS bit is set when the calling address matches the programmed slave address or IAAS when the GCAEN bit is set and a general call is received. Writing the IICC register clears this bit. 0 Not addressed 1 Addressed as a slave 5 Bus Busy. The BUSY bit indicates the status of the bus regardless of slave or master mode. The BUSY bit is BUSY set when a start signal is detected and cleared when a stop signal is detected. 0 Bus is idle 1 Bus is busy 4 Arbitration Lost. This bit is set by hardware when the arbitration procedure is lost. The ARBL bit must be cleared ARBL by software by writing a 1 to it. 0 Standard bus operation 1 Loss of arbitration 2 Slave Read/Write. When addressed as a slave, the SRW bit indicates the value of the R/W command bit of the SRW calling address sent to the master. 0 Slave receive, master writing to slave 1 Slave transmit, master reading from slave 1 IIC Interrupt Flag. The IICIF bit is set when an interrupt is pending. This bit must be cleared by software, by IICIF writing a 1 to it in the interrupt routine. One of the following events can set the IICIF bit: (cid:129) One byte transfer completes (cid:129) Match of slave address to calling address (cid:129) Arbitration lost 0 No interrupt pending 1 Interrupt pending 0 Receive Acknowledge. When the RXAK bit is low, it indicates an acknowledge signal has been received after RXAK the completion of one byte of data transmission on the bus. If the RXAK bit is high it means that no acknowledge signal is detected. 0 Acknowledge received 1 No acknowledge received 11.3.5 IIC Data I/O Register (IICD) 7 6 5 4 3 2 1 0 R DATA W Reset 0 0 0 0 0 0 0 0 Figure11-7. IIC Data I/O Register (IICD) MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 167

Table11-7. IICD Field Descriptions Field Description 7–0 Data — In master transmit mode, when data is written to the IICD, a data transfer is initiated. The most significant DATA bit is sent first. In master receive mode, reading this register initiates receiving of the next byte of data. NOTE When transitioning out of master receive mode, the IIC mode should be switched before reading the IICD register to prevent an inadvertent initiation of a master receive data transfer. In slave mode, the same functions are available after an address match has occurred. The TX bit in IICC must correctly reflect the desired direction of transfer in master and slave modes for the transmission to begin. For instance, if the IIC is configured for master transmit but a master receive is desired, reading the IICD does not initiate the receive. Reading the IICD returns the last byte received while the IIC is configured in master receive or slave receive modes. The IICD does not reflect every byte transmitted on the IIC bus, nor can software verify that a byte has been written to the IICD correctly by reading it back. In master transmit mode, the first byte of data written to IICD following assertion of MST is used for the address transfer and should comprise of the calling address (in bit 7 to bit 1) concatenated with the required R/W bit (in position bit 0). 11.3.6 IIC Control Register 2 (IICC2) 7 6 5 4 3 2 1 0 R 0 0 0 GCAEN ADEXT AD10 AD9 AD8 W Reset 0 0 0 0 0 0 0 0 = Unimplemented or Reserved Figure11-8. IIC Control Register (IICC2) Table11-8. IICC2 Field Descriptions Field Description 7 General Call Address Enable. The GCAEN bit enables or disables general call address. GCAEN 0 General call address is disabled 1 General call address is enabled 6 Address Extension. The ADEXT bit controls the number of bits used for the slave address. ADEXT 0 7-bit address scheme 1 10-bit address scheme 2–0 Slave Address. The AD[10:8] field contains the upper three bits of the slave address in the 10-bit address AD[10:8] scheme. This field is only valid when the ADEXT bit is set. MC9S08JM60 Series Data Sheet, Rev. 5 168 Freescale Semiconductor

11.4 Functional Description This section provides a complete functional description of the IIC module. 11.4.1 IIC Protocol The IIC bus system uses a serial data line (SDA) and a serial clock line (SCL) for data transfer. All devices connected to it must have open drain or open collector outputs. A logic AND function is exercised on both lines with external pull-up resistors. The value of these resistors is system dependent. Normally, a standard communication is composed of four parts: • Start signal • Slave address transmission • Data transfer • Stop signal The stop signal should not be confused with the CPU stop instruction. The IIC bus system communication is described briefly in the following sections and illustrated in Figure 11-9. msb lsb msb lsb SCL 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 SDA AD7 AD6 AD5 AD4 AD3 AD2 AD1 R/W XXX D7 D6 D5 D4 D3 D2 D1 D0 Start Calling Address Read/ Ack Data Byte No Stop Signal Write Bit Ack Signal Bit msb lsb msb lsb SCL 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 SDA AD7 AD6 AD5 AD4 AD3 AD2 AD1 R/W XX AD7 AD6 AD5 AD4 AD3 AD2 AD1 R/W Start Calling Address Read/ Ack Repeated New Calling Address Read/ No Stop Signal Write Bit Start Write Ack Signal Signal Bit Figure11-9. IIC Bus Transmission Signals 11.4.1.1 Start Signal When the bus is free, no master device is engaging the bus (SCL and SDA lines are at logical high), a master may initiate communication by sending a start signal. As shown in Figure11-9, a start signal is defined as a high-to-low transition of SDA while SCL is high. This signal denotes the beginning of a new data transfer (each data transfer may contain several bytes of data) and brings all slaves out of their idle states. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 169

11.4.1.2 Slave Address Transmission The first byte of data transferred immediately after the start signal is the slave address transmitted by the master. This is a seven-bit calling address followed by a R/W bit. The R/W bit tells the slave the desired direction of data transfer. 1 = Read transfer, the slave transmits data to the master. 0 = Write transfer, the master transmits data to the slave. Only the slave with a calling address that matches the one transmitted by the master responds by sending back an acknowledge bit. This is done by pulling the SDA low at the ninth clock (see Figure 11-9). No two slaves in the system may have the same address. If the IIC module is the master, it must not transmit an address equal to its own slave address. The IIC cannot be master and slave at the same time. However, if arbitration is lost during an address cycle, the IIC reverts to slave mode and operates correctly even if it is being addressed by another master. 11.4.1.3 Data Transfer Before successful slave addressing is achieved, the data transfer can proceed byte-by-byte in a direction specified by the R/W bit sent by the calling master. All transfers that come after an address cycle are referred to as data transfers, even if they carry sub-address information for the slave device Each data byte is 8 bits long. Data may be changed only while SCL is low and must be held stable while SCL is high as shown in Figure 11-9. There is one clock pulse on SCL for each data bit, the msb being transferred first. Each data byte is followed by a 9th (acknowledge) bit, which is signalled from the receiving device. An acknowledge is signalled by pulling the SDA low at the ninth clock. In summary, one complete data transfer needs nine clock pulses. If the slave receiver does not acknowledge the master in the ninth bit time, the SDA line must be left high by the slave. The master interprets the failed acknowledge as an unsuccessful data transfer. If the master receiver does not acknowledge the slave transmitter after a data byte transmission, the slave interprets this as an end of data transfer and releases the SDA line. In either case, the data transfer is aborted and the master does one of two things: • Relinquishes the bus by generating a stop signal. • Commences a new calling by generating a repeated start signal. 11.4.1.4 Stop Signal The master can terminate the communication by generating a stop signal to free the bus. However, the master may generate a start signal followed by a calling command without generating a stop signal first. This is called repeated start. A stop signal is defined as a low-to-high transition of SDA while SCL at logical 1 (see Figure 11-9). The master can generate a stop even if the slave has generated an acknowledge at which point the slave must release the bus. MC9S08JM60 Series Data Sheet, Rev. 5 170 Freescale Semiconductor

11.4.1.5 Repeated Start Signal As shown in Figure 11-9, a repeated start signal is a start signal generated without first generating a stop signal to terminate the communication. This is used by the master to communicate with another slave or with the same slave in different mode (transmit/receive mode) without releasing the bus. 11.4.1.6 Arbitration Procedure The IIC bus is a true multi-master bus that allows more than one master to be connected on it. If two or more masters try to control the bus at the same time, a clock synchronization procedure determines the bus clock, for which the low period is equal to the longest clock low period and the high is equal to the shortest one among the masters. The relative priority of the contending masters is determined by a data arbitration procedure, a bus master loses arbitration if it transmits logic 1 while another master transmits logic 0. The losing masters immediately switch over to slave receive mode and stop driving SDA output. In this case, the transition from master to slave mode does not generate a stop condition. Meanwhile, a status bit is set by hardware to indicate loss of arbitration. 11.4.1.7 Clock Synchronization Because wire-AND logic is performed on the SCL line, a high-to-low transition on the SCL line affects all the devices connected on the bus. The devices start counting their low period and after a device’s clock has gone low, it holds the SCL line low until the clock high state is reached. However, the change of low to high in this device clock may not change the state of the SCL line if another device clock is still within its low period. Therefore, synchronized clock SCL is held low by the device with the longest low period. Devices with shorter low periods enter a high wait state during this time (see Figure 11-10). When all devices concerned have counted off their low period, the synchronized clock SCL line is released and pulled high. There is then no difference between the device clocks and the state of the SCL line and all the devices start counting their high periods. The first device to complete its high period pulls the SCL line low again. Delay Start Counting High Period SCL1 SCL2 SCL Internal Counter Reset Figure11-10. IIC Clock Synchronization MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 171

11.4.1.8 Handshaking The clock synchronization mechanism can be used as a handshake in data transfer. Slave devices may hold the SCL low after completion of one byte transfer (9 bits). In such a case, it halts the bus clock and forces the master clock into wait states until the slave releases the SCL line. 11.4.1.9 Clock Stretching The clock synchronization mechanism can be used by slaves to slow down the bit rate of a transfer. After the master has driven SCL low the slave can drive SCL low for the required period and then release it. If the slave SCL low period is greater than the master SCL low period then the resulting SCL bus signal low period is stretched. 11.4.2 10-bit Address For 10-bit addressing, 0x11110 is used for the first 5 bits of the first address byte. Various combinations of read/write formats are possible within a transfer that includes 10-bit addressing. 11.4.2.1 Master-Transmitter Addresses a Slave-Receiver The transfer direction is not changed (see Table11-9). When a 10-bit address follows a start condition, each slave compares the first seven bits of the first byte of the slave address (11110XX) with its own address and tests whether the eighth bit (R/W direction bit) is 0. More than one device can find a match and generate an acknowledge (A1). Then, each slave that finds a match compares the eight bits of the second byte of the slave address with its own address. Only one slave finds a match and generates an acknowledge (A2). The matching slave remains addressed by the master until it receives a stop condition (P) or a repeated start condition (Sr) followed by a different slave address. Slave Address 1st 7 bits R/W Slave Address 2nd byte S A1 A2 Data A ... Data A/A P 11110 + AD10 + AD9 0 AD[8:1] Table11-9. Master-Transmitter Addresses Slave-Receiver with a 10-bit Address After the master-transmitter has sent the first byte of the 10-bit address, the slave-receiver sees an IIC interrupt. Software must ensure the contents of IICD are ignored and not treated as valid data for this interrupt. 11.4.2.2 Master-Receiver Addresses a Slave-Transmitter The transfer direction is changed after the second R/W bit (see Table 11-10). Up to and including acknowledge bit A2, the procedure is the same as that described for a master-transmitter addressing a slave-receiver. After the repeated start condition (Sr), a matching slave remembers that it was addressed before. This slave then checks whether the first seven bits of the first byte of the slave address following Sr are the same as they were after the start condition (S) and tests whether the eighth (R/W) bit is 1. If there is a match, the slave considers that it has been addressed as a transmitter and generates acknowledge A3. The slave-transmitter remains addressed until it receives a stop condition (P) or a repeated start condition (Sr) followed by a different slave address. MC9S08JM60 Series Data Sheet, Rev. 5 172 Freescale Semiconductor

After a repeated start condition (Sr), all other slave devices also compare the first seven bits of the first byte of the slave address with their own addresses and test the eighth (R/W) bit. However, none of them are addressed because R/W = 1 (for 10-bit devices) or the 11110XX slave address (for 7-bit devices) does not match. Slave Address Slave Address Slave Address R/W R/W S 1st 7 bits A1 2nd byte A2 Sr 1st 7 bits A3 Data A ... Data A P 11110 + AD10 + AD9 0 AD[8:1] 11110 + AD10 + AD9 1 Table11-10. Master-Receiver Addresses a Slave-Transmitter with a 10-bit Address After the master-receiver has sent the first byte of the 10-bit address, the slave-transmitter sees an IIC interrupt. Software must ensure the contents of IICD are ignored and not treated as valid data for this interrupt. 11.4.3 General Call Address General calls can be requested in 7-bit address or 10-bit address. If the GCAEN bit is set, the IIC matches the general call address as well as its own slave address. When the IIC responds to a general call, it acts as a slave-receiver and the IAAS bit is set after the address cycle. Software must read the IICD register after the first byte transfer to determine whether the address matches is its own slave address or a general call. If the value is 00, the match is a general call. If the GCAEN bit is clear, the IIC ignores any data supplied from a general call address by not issuing an acknowledgement. 11.5 Resets The IIC is disabled after reset. The IIC cannot cause an MCU reset. 11.6 Interrupts The IIC generates a single interrupt. An interrupt from the IIC is generated when any of the events in Table 11-11 occur, provided the IICIE bit is set. The interrupt is driven by bit IICIF (of the IIC status register) and masked with bit IICIE (of the IIC control register). The IICIF bit must be cleared by software by writing a 1 to it in the interrupt routine. You can determine the interrupt type by reading the status register. Table11-11. Interrupt Summary Interrupt Source Status Flag Local Enable Complete 1-byte transfer TCF IICIF IICIE Match of received calling address IAAS IICIF IICIE Arbitration Lost ARBL IICIF IICIE 11.6.1 Byte Transfer Interrupt The TCF (transfer complete flag) bit is set at the falling edge of the ninth clock to indicate the completion of byte transfer. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 173

11.6.2 Address Detect Interrupt When the calling address matches the programmed slave address (IIC address register) or when the GCAEN bit is set and a general call is received, the IAAS bit in the status register is set. The CPU is interrupted, provided the IICIE is set. The CPU must check the SRW bit and set its Tx mode accordingly. 11.6.3 Arbitration Lost Interrupt The IIC is a true multi-master bus that allows more than one master to be connected on it. If two or more masters try to control the bus at the same time, the relative priority of the contending masters is determined by a data arbitration procedure. The IIC module asserts this interrupt when it loses the data arbitration process and the ARBL bit in the status register is set. Arbitration is lost in the following circumstances: • SDA sampled as a low when the master drives a high during an address or data transmit cycle. • SDA sampled as a low when the master drives a high during the acknowledge bit of a data receive cycle. • A start cycle is attempted when the bus is busy. • A repeated start cycle is requested in slave mode. • A stop condition is detected when the master did not request it. This bit must be cleared by software writing a 1 to it. MC9S08JM60 Series Data Sheet, Rev. 5 174 Freescale Semiconductor

11.7 Initialization/Application Information Module Initialization (Slave) 1. Write: IICC2 — to enable or disable general call — to select 10-bit or 7-bit addressing mode 2. Write: IICA — to set the slave address 3. Write: IICC1 — to enable IIC and interrupts 4. Initialize RAM variables (IICEN = 1 and IICIE = 1) for transmit data 5. Initialize RAM variables used to achieve the routine shown in Figure 11-12 Module Initialization (Master) 1. Write: IICF — to set the IIC baud rate (example provided in this chapter) 2. Write: IICC1 — to enable IIC and interrupts 3. Initialize RAM variables (IICEN = 1 and IICIE = 1) for transmit data 4. Initialize RAM variables used to achieve the routine shown in Figure 11-12 5. Write: IICC1 — to enable TX Register Model IICA AD[7:1] 0 When addressed as a slave (in slave mode), the module responds to this address IICF MULT ICR Baud rate = BUSCLK / (2 x MULT x (SCL DIVIDER)) IICC1 IICEN IICIE MST TX TXAK RSTA 0 0 Module configuration IICS TCF IAAS BUSY ARBL 0 SRW IICIF RXAK Module status flags IICD DATA Data register; Write to transmit IIC data read to read IIC data IICC2 GCAEN ADEXT 0 0 0 AD10 AD9 AD8 Address configuration Figure11-11. IIC Module Quick Start MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 175

Clear IICIF Y Master N Mode ? TX Tx/Rx RX Y Arbitration Lost ? ? N Last Byte Transmitted Y Clear ARBL ? N RXAK=0 N Byte tLoa Bset Read Y N IAAS=1 Y IAAS=1 ? ? ? ? Y N Y N Address Transfer Data Transfer See Note 1 See Note 2 Y Y AdEdnr dC oyfc le Y Byte2 tnod B Lea sRt ead (Read) SRW=1 TX/RX RX (Mast?er Rx) ? ? ? N N N(Write) TX Write Next Generate Set TX Y ACK from Set TXACK =1 Stop Signal Receiver Byte to IICD Mode (MST = 0) ? N Read Data Write Data Tx Next from IICD to IICD Byte and Store Switch to Set RX Switch to Rx Mode Mode Rx Mode Generate Read Data Dummy Read Dummy Read Dummy Read Stop Signal from IICD from IICD from IICD from IICD (MST = 0) and Store RTI NOTES: 1. If general call is enabled, a check must be done to determine whether the received address was a general call address (0x00). If the received address was a general call address, then the general call must be handled by user software. 2. When 10-bit addressing is used to address a slave, the slave sees an interrupt following the first byte of the extended address. Figure11-12. Typical IIC Interrupt Routine MC9S08JM60 Series Data Sheet, Rev. 5 176 Freescale Semiconductor

MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 177

MC9S08JM60 Series Data Sheet, Rev. 5 178 Freescale Semiconductor

Chapter 12 Multi-Purpose Clock Generator (S08MCGV1) 12.1 Introduction The multi-purpose clock generator (MCG) module provides several clock source choices for the MCU. which contains a frequency-locked loop (FLL) and a phase-locked loop (PLL). The module can select either of the FLL or PLL clocks, or either of the internal or external reference clocks as a source for the MCU system clock. Whichever clock source is chosen, it is passed through a reduced bus divider which allows a lower output clock frequency to be derived. The MCG also controls an external oscillator (XOSC) for the use of a crystal or resonator as the external reference clock. For USB operation on the MC9S08JM60 series, the MCG must be configured for PLL engaged external (PEE) mode in order to achieve a MCGOUT frequency of 48 MHz MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 179

Chapter12 Multi-Purpose Clock Generator (S08MCGV1) USBDP ON-CHIP ICE AND USBDN HCS08 CORE DEBUG MODULE (DBG) A T 6 R PTA5– PTA0 O USB SIE P BKGD/MS FULL SPEED PTB7/ADP7 BDC CPU USB PTB6/ADP6 USB ENDPOINT TRANSCEIVER PTB5/KBIP5/ADP5 RAM B T PTB4/KBIP4/ADP4 SSPSS2CK2 POR PTB3/SS2/ADP3 RESET HCS08 SYSTEM CONTROL 8-/16-BIT SERIAL PERIPHERAL MOSI2 PTB2/SPSCK2/ADP2 INTERFACE MODULE (SPI2) PTB1/MOSI2/ADP1 MISO2 PTB0/MISO2/ADP0 RESETS AND INTERRUPTS MODES OF OPERATION PTC6 IRQ/TPMCLK POWER MANAGEMENT SERIAL COMMUNICATIONS RxD2 PTC5/RxD2 COP IRQ LVD INTERFACE MODULE (SCI2) TxD2 ORT C PPTTCC34/TxD2 P PTC2 SDA PTC1/SDA IIC MODULE (IIC) SCL PTC0/SCL VDDAD 12-CHANNEL, 12-BIT 8 PTD7 VSSAD ANALOG-TO-DIGITAL 4 PTD6 VREFL CONVERTER (ADC) PTD5 VREFH D PTD4/ADP11 T R PTD3/KBIP3/ADP10 O USER Flash (IN BYTES) P PTD2/KBIP2/ACMPO ACMP– MC9S08JM60 = 60,912 PTD1/ADP9/ACMP– MC9S08JM32 = 32,768 ANALOG COMPARATOR ACMP+ PTD0/ADP8/ACMP+ (ACMP) ACMPO SS1 PTE7/SS1 USER RAM (IN BYTES) SPSCK1 8-/16-BIT SERIAL PERIPHERAL PTE6/SPSCK1 MMCC99SS0088JJMM6302 == 42009468 INTERFACE MODULE (SPI1) MOSI1 PTE5/MOSI1 MISO1 PTE4/MISO1 TPMCLK E MULTI-PURPOSE CLOCK 6-CHMAONDNUELLE T (IMTPEMR1/P)WM TTPPMM11CCHH10 PORT PTE3/TPM1CH1 GENERATOR (MCG) PTE2/TPM1CH0 TPM1CHx4 RxD1 SERIAL COMMUNICATIONS PTE1/RxD1 VSSOSC LOW-POWER OSCILLATOR TxD1 PTE0/TxD1 INTERFACE MODULE (SCI1) PTF7 VDD SYSTEM TPMCLK PTF6 VSS RVEOGLUTLAAGTEO R 2-CHMAONDNUELLE T (IMTPEMR2/P)WM TTPPMM22CCHH10 T F PPTTFF54//TTPPMM22CCHH10 OR PTF3/TPM1CH5 KBIPx P PTF2/TPM1CH4 VUSB33 USB 3.3-V VOLTAGE REGULATOR 8-BIT KEYBOARD 4 PTF1/TPM1CH3 INTERRUPT MODULE (KBI) KBIPx 4 PTF0/TPM1CH2 REAL-TIME COUNTER (RTC) EXTAL PTG5/EXTAL XTAL NOTES: G PTG4/XTAL 1. Port pins are software configurable with pullup device if input port. RT PTG3/KBIP7 O PTG2/KBIP6 2. Pin contains software configurable pullup/pull-down device if IRQ is enabled P PTG1/KBIP1 (IRQPE=1). Pull-down is enabled if rising edge detect is selected (IRQEDG=1) PTG0/KBIP0 3. IRQ does not have a clamp diode to V . IRQ must not be driven above V . DD DD 4. Pin contains integrated pullup device. 5. When pin functions as KBI (KBIPEn = 1) and associated pin is configured to enable the pullup device, KBEDGn can be used to reconfigure the pullup as a pull-down device. Figure12-1. MC9S08JM60 Series Block Diagram Highlighting MCG Block and Pins MC9S08JM60 Series Data Sheet, Rev. 5 180 Freescale Semiconductor

Multi-Purpose Clock Generator (S08MCGV1) 12.1.1 Features Key features of the MCG module are: • Frequency-locked loop (FLL) — 0.2% resolution using internal 32-kHz reference — 2% deviation over voltage and temperature using internal 32-kHz reference — Internal or external reference can be used to control the FLL • Phase-locked loop (PLL) — Voltage-controlled oscillator (VCO) — Modulo VCO frequency divider — Phase/Frequency detector — Integrated loop filter — Lock detector with interrupt capability • Internal reference clock — Nine trim bits for accuracy — Can be selected as the clock source for the MCU • External reference clock — Control for external oscillator — Clock monitor with reset capability — Can be selected as the clock source for the MCU • Reference divider is provided • Clock source selected can be divided down by 1, 2, 4, or 8 • BDC clock (MCGLCLK) is provided as a constant divide by 2 of the DCO output whether in an FLL or PLL mode. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 181

Multi-Purpose Clock Generator (S08MCGV1) External Oscillator (XOSC) MCGERCLK ERCLKEN RANGE EREFS HGO EREFSTEN IRCLKEN MCGIRCLK CME IREFSTEN CLKS BDIV Clock Monitor / 2n Internal MCGOUT n=0-3 Reference LP LOC OSCINIT Clock IREFS 9 DCO DCOOUT TRIM Lock PLLS Detector / 2n RDIV_CLK Filter n=0-7 FLL LOLS LOCK MCGFFCLK RDIV LP VCOOUT / 2 MCGLCLK Phase Charge Detector Pump VCO Internal VDIV Filter PLL /(4,8,12,...,40) Multi-purpose Clock Generator (MCG) Figure12-2. Multi-Purpose Clock Generator (MCG) Block Diagram MC9S08JM60 Series Data Sheet, Rev. 5 182 Freescale Semiconductor

Multi-Purpose Clock Generator (S08MCGV1) 12.1.2 Modes of Operation There are nine modes of operation for the MCG: • FLL Engaged Internal (FEI) • FLL Engaged External (FEE) • FLL Bypassed Internal (FBI) • FLL Bypassed External (FBE) • PLL Engaged External (PEE) • PLL Bypassed External (PBE) • Bypassed Low Power Internal (BLPI) • Bypassed Low Power External (BLPE) • Stop For details see Section12.4.1, “Operational Modes.” 12.2 External Signal Description There are no MCG signals that connect off chip. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 183

Multi-Purpose Clock Generator (S08MCGV1) 12.3 Register Definition 12.3.1 MCG Control Register 1 (MCGC1) 7 6 5 4 3 2 1 0 R CLKS RDIV IREFS IRCLKEN IREFSTEN W Reset: 0 0 0 0 0 1 0 0 Figure12-3. MCG Control Register 1 (MCGC1) Table12-1. MCG Control Register 1 Field Descriptions Field Description 7:6 Clock Source Select — Selects the system clock source. CLKS 00 Encoding 0 — Output of FLL or PLL is selected. 01 Encoding 1 — Internal reference clock is selected. 10 Encoding 2 — External reference clock is selected. 11 Encoding 3 — Reserved, defaults to 00. 5:3 Reference Divider — Selects the amount to divide down the reference clock selected by the IREFS bit. If the RDIV FLL is selected, the resulting frequency must be in the range 31.25 kHz to 39.0625 kHz. If the PLL is selected, the resulting frequency must be in the range 1 MHz to 2 MHz. 000 Encoding 0 — Divides reference clock by 1 (reset default) 001 Encoding 1 — Divides reference clock by 2 010 Encoding 2 — Divides reference clock by 4 011 Encoding 3 — Divides reference clock by 8 100 Encoding 4 — Divides reference clock by 16 101 Encoding 5 — Divides reference clock by 32 110 Encoding 6 — Divides reference clock by 64 111 Encoding 7 — Divides reference clock by 128 2 Internal Reference Select — Selects the reference clock source. IREFS 1 Internal reference clock selected 0 External reference clock selected 1 Internal Reference Clock Enable — Enables the internal reference clock for use as MCGIRCLK. IRCLKEN 1 MCGIRCLK active 0 MCGIRCLK inactive 0 Internal Reference Stop Enable — Controls whether or not the internal reference clock remains enabled when IREFSTEN the MCG enters stop mode. 1 Internal reference clock stays enabled in stop if IRCLKEN is set or if MCG is in FEI, FBI, or BLPI mode before entering stop 0 Internal reference clock is disabled in stop MC9S08JM60 Series Data Sheet, Rev. 5 184 Freescale Semiconductor

Multi-Purpose Clock Generator (S08MCGV1) 12.3.2 MCG Control Register 2 (MCGC2) 7 6 5 4 3 2 1 0 R BDIV RANGE HGO LP EREFS ERCLKEN EREFSTEN W Reset: 0 1 0 0 0 0 0 0 Figure12-4. MCG Control Register 2 (MCGC2) Table12-2. MCG Control Register 2 Field Descriptions Field Description 7:6 Bus Frequency Divider — Selects the amount to divide down the clock source selected by the CLKS bits in the BDIV MCGC1 register. This controls the bus frequency. 00 Encoding 0 — Divides selected clock by 1 01 Encoding 1 — Divides selected clock by 2 (reset default) 10 Encoding 2 — Divides selected clock by 4 11 Encoding 3 — Divides selected clock by 8 5 Frequency Range Select — Selects the frequency range for the external oscillator or external clock source. RANGE 1 High frequency range selected for the external oscillator of 1 MHz to 16 MHz (1 MHz to 40 MHz for external clock source) 0 Low frequency range selected for the external oscillator of 32 kHz to 100 kHz (32 kHz to 1 MHz for external clock source) 4 High Gain Oscillator Select — Controls the external oscillator mode of operation. HGO 1 Configure external oscillator for high gain operation 0 Configure external oscillator for low power operation 3 Low Power Select — Controls whether the FLL (or PLL) is disabled in bypassed modes. LP 1 FLL (or PLL) is disabled in bypass modes (lower power). 0 FLL (or PLL) is not disabled in bypass modes. 2 External Reference Select — Selects the source for the external reference clock. EREFS 1 Oscillator requested 0 External Clock Source requested 1 External Reference Enable — Enables the external reference clock for use as MCGERCLK. ERCLKEN 1 MCGERCLK active 0 MCGERCLK inactive 0 External Reference Stop Enable — Controls whether or not the external reference clock remains enabled when EREFSTEN the MCG enters stop mode. 1 External reference clock stays enabled in stop if ERCLKEN is set or if MCG is in FEE, FBE, PEE, PBE, or BLPE mode before entering stop 0 External reference clock is disabled in stop MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 185

Multi-Purpose Clock Generator (S08MCGV1) 12.3.3 MCG Trim Register (MCGTRM) 7 6 5 4 3 2 1 0 R TRIM W POR: 1 0 0 0 0 0 0 0 Reset: U U U U U U U U Figure12-5. MCG Trim Register (MCGTRM) Table12-3. MCG Trim Register Field Descriptions Field Description 7:0 MCG Trim Setting — Controls the internal reference clock frequency by controlling the internal reference clock TRIM period. The TRIM bits are binary weighted (i.e., bit 1 will adjust twice as much as bit 0). Increasing the binary value in TRIM will increase the period, and decreasing the value will decrease the period. An additional fine trim bit is available in MCGSC as the FTRIM bit. If a TRIM[7:0] value stored in nonvolatile memory is to be used, it’s the user’s responsibility to copy that value from the nonvolatile memory location to this register. MC9S08JM60 Series Data Sheet, Rev. 5 186 Freescale Semiconductor

Multi-Purpose Clock Generator (S08MCGV1) 12.3.4 MCG Status and Control Register (MCGSC) 7 6 5 4 3 2 1 0 R LOLS LOCK PLLST IREFST CLKST OSCINIT FTRIM W POR: 0 0 0 1 0 0 0 0 Reset: 0 0 0 1 0 0 0 U Figure12-6. MCG Status and Control Register (MCGSC) Table12-4. MCG Status and Control Register Field Descriptions Field Description 7 Loss of Lock Status — This bit is a sticky indication of lock status for the FLL or PLL. LOLS is set when lock LOLS detection is enabled and after acquiring lock, the FLL or PLL output frequency has fallen outside the lock exit frequency tolerance, D . LOLIE determines whether an interrupt request is made when set. LOLS is cleared by unl reset or by writing a logic 1 to LOLS when LOLS is set. Writing a logic 0 to LOLS has no effect. 0 FLL or PLL has not lost lock since LOLS was last cleared. 1 FLL or PLL has lost lock since LOLS was last cleared. 6 Lock Status — Indicates whether the FLL or PLL has acquired lock. Lock detection is disabled when both the LOCK FLL and PLL are disabled. If the lock status bit is set then changing the value of any of the following bits IREFS, PLLS, RDIV[2:0], TRIM[7:0] (if in FEI or FBI modes), or VDIV[3:0] (if in PBE or PEE modes), will cause the lock status bit to clear and stay cleared until the FLL or PLL has reacquired lock. Stop mode entry will also cause the lock status bit to clear and stay cleared until the FLL or PLL has reacquired lock. Entry into BLPI or BLPE mode will also cause the lock status bit to clear and stay cleared until the MCG has exited these modes and the FLL or PLL has reacquired lock. 0 FLL or PLL is currently unlocked. 1 FLL or PLL is currently locked. 5 PLL Select Status — The PLLST bit indicates the current source for the PLLS clock. The PLLST bit does not PLLST update immediately after a write to the PLLS bit due to internal synchronization between clock domains. 0 Source of PLLS clock is FLL clock. 1 Source of PLLS clock is PLL clock. 4 Internal Reference Status — The IREFST bit indicates the current source for the reference clock. The IREFST IREFST bit does not update immediately after a write to the IREFS bit due to internal synchronization between clock domains. 0 Source of reference clock is external reference clock (oscillator or external clock source as determined by the EREFS bit in the MCGC2 register). 1 Source of reference clock is internal reference clock. 3:2 Clock Mode Status — The CLKST bits indicate the current clock mode. The CLKST bits do not update CLKST immediately after a write to the CLKS bits due to internal synchronization between clock domains. 00 Encoding 0 — Output of FLL is selected. 01 Encoding 1 — Internal reference clock is selected. 10 Encoding 2 — External reference clock is selected. 11 Encoding 3 — Output of PLL is selected. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 187

Multi-Purpose Clock Generator (S08MCGV1) Table12-4. MCG Status and Control Register Field Descriptions (continued) Field Description 1 OSC Initialization — If the external reference clock is selected by ERCLKEN or by the MCG being in FEE, FBE, OSCINIT PEE, PBE, or BLPE mode, and if EREFS is set, then this bit is set after the initialization cycles of the external oscillator clock have completed. This bit is only cleared when either EREFS is cleared or when the MCG is in either FEI, FBI, or BLPI mode and ERCLKEN is cleared. 0 MCG Fine Trim — Controls the smallest adjustment of the internal reference clock frequency. Setting FTRIM FTRIM will increase the period and clearing FTRIM will decrease the period by the smallest amount possible. If an FTRIM value stored in nonvolatile memory is to be used, it’s the user’s responsibility to copy that value from the nonvolatile memory location to this register’s FTRIM bit. 12.3.5 MCG Control Register 3 (MCGC3) 7 6 5 4 3 2 1 0 R 0 LOLIE PLLS CME VDIV W Reset: 0 0 0 0 0 0 0 1 Figure12-7. MCG PLL Register (MCGPLL) Table12-5. MCG PLL Register Field Descriptions Field Description 7 Loss of Lock Interrupt Enable — Determines if an interrupt request is made following a loss of lock indication. LOLIE The LOLIE bit only has an effect when LOLS is set. 0 No request on loss of lock. 1 Generate an interrupt request on loss of lock. 6 PLL Select — Controls whether the PLL or FLL is selected. If the PLLS bit is clear, the PLL is disabled in all PLLS modes. If the PLLS is set, the FLL is disabled in all modes. 1 PLL is selected 0 FLL is selected MC9S08JM60 Series Data Sheet, Rev. 5 188 Freescale Semiconductor

Multi-Purpose Clock Generator (S08MCGV1) Table12-5. MCG PLL Register Field Descriptions (continued) Field Description 5 Clock Monitor Enable — Determines if a reset request is made following a loss of external clock indication. The CME CME bit should only be set to a logic 1 when either the MCG is in an operational mode that uses the external clock (FEE, FBE, PEE, PBE, or BLPE) or the external reference is enabled (ERCLKEN=1 in the MCGC2 register). Whenever the CME bit is set to a logic 1, the value of the RANGE bit in the MCGC2 register should not be changed. 0 Clock monitor is disabled. 1 Generate a reset request on loss of external clock. 3:0 VCO Divider — Selects the amount to divide down the VCO output of PLL. The VDIV bits establish the VDIV multiplication factor (M) applied to the reference clock frequency. 0000Encoding 0 — Reserved. 0001Encoding 1 — Multiply by 4. 0010Encoding 2 — Multiply by 8. 0011Encoding 3 — Multiply by 12. 0100Encoding 4 — Multiply by 16. 0101Encoding 5 — Multiply by 20. 0110Encoding 6 — Multiply by 24. 0111Encoding 7 — Multiply by 28. 1000Encoding 8 — Multiply by 32. 1001Encoding 9 — Multiply by 36. 1010Encoding 10 — Multiply by 40. 1011Encoding 11 — Reserved (default to M=40). 11xxEncoding 12-15 — Reserved (default to M=40). MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 189

Multi-Purpose Clock Generator (S08MCGV1) 12.4 Functional Description 12.4.1 Operational Modes IREFS=1 IREFS=0 CLKS=00 FLL Engaged FLL Engaged CLKS=00 PLLS=0 Internal (FEI) External (FEE) PLLS=0 IREFS=1 IREFS=0 CLKS=01 CLKS=10 PLLS=0 PLLS=0 IREFS=0 BDM Enabled FLL Bypassed FLL Bypassed BDM Enabled CLKS=10 or LP=0 or LP=0 BDM Disabled Internal (FBI) External (FBE) and LP=1 Bypassed Bypassed IREFS=1 Low Power Low Power CLKS=01 Internal (BLPI) External (BLPE) BDM Disabled and LP=1 PLL Bypassed IREFS=0 External (PBE) CLKS=10 PLLS=1 BDM Enabled or LP=0 PLL Engaged IREFS=0 External (PEE) CLKS=00 PLLS=1 Returns to state that was active Entered from any state Stop before MCU entered stop, unless when MCU enters stop RESET occurs while in stop. Figure12-8. Clock Switching Modes The nine states of the MCG are shown as a state diagram and are described below. The arrows indicate the allowed movements between the states. 12.4.1.1 FLL Engaged Internal (FEI) FLL engaged internal (FEI) is the default mode of operation and is entered when all the following conditions occur: • CLKS bits are written to 00 • IREFS bit is written to 1 • PLLS bit is written to 0 • RDIV bits are written to 000. Since the internal reference clock frequency should already be in the range of 31.25 kHz to 39.0625 kHz after it is trimmed, no further frequency divide is necessary. MC9S08JM60 Series Data Sheet, Rev. 5 190 Freescale Semiconductor

Multi-Purpose Clock Generator (S08MCGV1) In FLL engaged internal mode, the MCGOUT clock is derived from the FLL clock, which is controlled by the internal reference clock. The FLL clock frequency locks to 1024 times the reference frequency, as selected by the RDIV bits. The MCGLCLK is derived from the FLL and the PLL is disabled in a low power state. 12.4.1.2 FLL Engaged External (FEE) The FLL engaged external (FEE) mode is entered when all the following conditions occur: • CLKS bits are written to 00 • IREFS bit is written to 0 • PLLS bit is written to 0 • RDIV bits are written to divide reference clock to be within the range of 31.25 kHz to 39.0625 kHz In FLL engaged external mode, the MCGOUT clock is derived from the FLL clock which is controlled by the external reference clock. The external reference clock which is enabled can be an external crystal/resonator or it can be another external clock source.The FLL clock frequency locks to 1024 times the reference frequency, as selected by the RDIV bits. The MCGLCLK is derived from the FLL and the PLL is disabled in a low power state. 12.4.1.3 FLL Bypassed Internal (FBI) In FLL bypassed internal (FBI) mode, the MCGOUT clock is derived from the internal reference clock and the FLL is operational but its output clock is not used. This mode is useful to allow the FLL to acquire its target frequency while the MCGOUT clock is driven from the internal reference clock. The FLL bypassed internal mode is entered when all the following conditions occur: • CLKS bits are written to 01 • IREFS bit is written to 1 • PLLS bit is written to 0 • RDIV bits are written to 000. Since the internal reference clock frequency should already be in the range of 31.25 kHz to 39.0625 kHz after it is trimmed, no further frequency divide is necessary. • LP bit is written to 0 In FLL bypassed internal mode, the MCGOUT clock is derived from the internal reference clock. The FLL clock is controlled by the internal reference clock, and the FLL clock frequency locks to 1024 times the reference frequency, as selected by the RDIV bits. The MCGLCLK is derived from the FLL and the PLL is disabled in a low power state. 12.4.1.4 FLL Bypassed External (FBE) In FLL bypassed external (FBE) mode, the MCGOUT clock is derived from the external reference clock and the FLL is operational but its output clock is not used. This mode is useful to allow the FLL to acquire its target frequency while the MCGOUT clock is driven from the external reference clock. The FLL bypassed external mode is entered when all the following conditions occur: MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 191

Multi-Purpose Clock Generator (S08MCGV1) • CLKS bits are written to 10 • IREFS bit is written to 0 • PLLS bit is written to 0 • RDIV bits are written to divide reference clock to be within the range of 31.25 kHz to 39.0625 kHz • LP bit is written to 0 In FLL bypassed external mode, the MCGOUT clock is derived from the external reference clock. The external reference clock which is enabled can be an external crystal/resonator or it can be another external clock source.The FLL clock is controlled by the external reference clock, and the FLL clock frequency locks to 1024 times the reference frequency, as selected by the RDIV bits. The MCGLCLK is derived from the FLL and the PLL is disabled in a low power state. NOTE It is possible to briefly operate in FBE mode with an FLL reference clock frequency that is greater than the specified maximum frequency. This can be necessary in applications that operate in PEE mode using an external crystal with a frequency above 5 MHz. Please see 12.5.2.4, “Example # 4: Moving from FEI to PEE Mode: External Crystal = 8 MHz, Bus Frequency = 8 MHz for a detailed example. 12.4.1.5 PLL Engaged External (PEE) The PLL engaged external (PEE) mode is entered when all the following conditions occur: • CLKS bits are written to 00 • IREFS bit is written to 0 • PLLS bit is written to 1 • RDIV bits are written to divide reference clock to be within the range of 1 MHz to 2 MHz In PLL engaged external mode, the MCGOUT clock is derived from the PLL clock which is controlled by the external reference clock. The external reference clock which is enabled can be an external crystal/resonator or it can be another external clock source The PLL clock frequency locks to a multiplication factor, as selected by the VDIV bits, times the reference frequency, as selected by the RDIV bits. If BDM is enabled then the MCGLCLK is derived from the DCO (open-loop mode) divided by two. If BDM is not enabled then the FLL is disabled in a low power state. MC9S08JM60 Series Data Sheet, Rev. 5 192 Freescale Semiconductor

Multi-Purpose Clock Generator (S08MCGV1) 12.4.1.6 PLL Bypassed External (PBE) In PLL bypassed external (PBE) mode, the MCGOUT clock is derived from the external reference clock and the PLL is operational but its output clock is not used. This mode is useful to allow the PLL to acquire its target frequency while the MCGOUT clock is driven from the external reference clock. The PLL bypassed external mode is entered when all the following conditions occur: • CLKS bits are written to 10 • IREFS bit is written to 0 • PLLS bit is written to 1 • RDIV bits are written to divide reference clock to be within the range of 1 MHz to 2 MHz • LP bit is written to 0 In PLL bypassed external mode, the MCGOUT clock is derived from the external reference clock. The external reference clock which is enabled can be an external crystal/resonator or it can be another external clock source. The PLL clock frequency locks to a multiplication factor, as selected by the VDIV bits, times the reference frequency, as selected by the RDIV bits. If BDM is enabled then the MCGLCLK is derived from the DCO (open-loop mode) divided by two. If BDM is not enabled then the FLL is disabled in a low power state. 12.4.1.7 Bypassed Low Power Internal (BLPI) The bypassed low power internal (BLPI) mode is entered when all the following conditions occur: • CLKS bits are written to 01 • IREFS bit is written to 1 • PLLS bit is written to 0 or 1 • LP bit is written to 1 • BDM mode is not active In bypassed low power internal mode, the MCGOUT clock is derived from the internal reference clock. The PLL and the FLL are disabled at all times in BLPI mode and the MCGLCLK will not be available for BDC communications If the BDM becomes active the mode will switch to one of the bypassed internal modes as determined by the state of the PLLS bit. 12.4.1.8 Bypassed Low Power External (BLPE) The bypassed low power external (BLPE) mode is entered when all the following conditions occur: • CLKS bits are written to 10 • IREFS bit is written to 0 • PLLS bit is written to 0 or 1 • LP bit is written to 1 • BDM mode is not active MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 193

Multi-Purpose Clock Generator (S08MCGV1) In bypassed low power external mode, the MCGOUT clock is derived from the external reference clock. The external reference clock which is enabled can be an external crystal/resonator or it can be another external clock source. The PLL and the FLL are disabled at all times in BLPE mode and the MCGLCLK will not be available for BDC communications. If the BDM becomes active the mode will switch to one of the bypassed external modes as determined by the state of the PLLS bit. 12.4.1.9 Stop Stop mode is entered whenever the MCU enters a STOP state. In this mode, the FLL and PLL are disabled and all MCG clock signals are static except in the following cases: MCGIRCLK will be active in stop mode when all the following conditions occur: • IRCLKEN = 1 • IREFSTEN = 1 MCGERCLK will be active in stop mode when all the following conditions occur: • ERCLKEN = 1 • EREFSTEN = 1 12.4.2 Mode Switching When switching between engaged internal and engaged external modes the IREFS bit can be changed at anytime, but the RDIV bits must be changed simultaneously so that the reference frequency stays in the range required by the state of the PLLS bit (31.25 kHz to 39.0625 kHz if the FLL is selected, or 1 MHz to 2 MHz if the PLL is selected). After a change in the IREFS value the FLL or PLL will begin locking again after the switch is completed. The completion of the switch is shown by the IREFST bit. For the special case of entering stop mode immediately after switching to FBE mode, if the external clock and the internal clock are disabled in stop mode, (EREFSTEN = 0 and IREFSTEN = 0), it is necessary to allow 100us after the IREFST bit is cleared to allow the internal reference to shutdown. For most cases the delay due to instruction execution times will be sufficient. The CLKS bits can also be changed at anytime, but in order for the MCGLCLK to be configured correctly the RDIV bits must be changed simultaneously so that the reference frequency stays in the range required by the state of the PLLS bit (31.25 kHz to 39.0625 kHz if the FLL is selected, or 1 MHz to 2MHz if the PLL is selected). The actual switch to the newly selected clock will be shown by the CLKST bits. If the newly selected clock is not available, the previous clock will remain selected. For details see Figure12-8. 12.4.3 Bus Frequency Divider The BDIV bits can be changed at anytime and the actual switch to the new frequency will occur immediately. MC9S08JM60 Series Data Sheet, Rev. 5 194 Freescale Semiconductor

Multi-Purpose Clock Generator (S08MCGV1) 12.4.4 Low Power Bit Usage The low power bit (LP) is provided to allow the FLL or PLL to be disabled and thus conserve power when these systems are not being used. However, in some applications it may be desirable to enable the FLL or PLL and allow it to lock for maximum accuracy before switching to an engaged mode. Do this by writing the LP bit to 0. 12.4.5 Internal Reference Clock When IRCLKEN is set the internal reference clock signal will be presented as MCGIRCLK, which can be used as an additional clock source. The MCGIRCLK frequency can be re-targeted by trimming the period of the internal reference clock. This can be done by writing a new value to the TRIM bits in the MCGTRM register. Writing a larger value will decrease the MCGIRCLK frequency, and writing a smaller value to the MCGTRM register will increase the MCGIRCLK frequency. The TRIM bits will effect the MCGOUT frequency if the MCG is in FLL engaged internal (FEI), FLL bypassed internal (FBI), or bypassed low power internal (BLPI) mode. The TRIM and FTRIM value is initialized by POR but is not affected by other resets. Until MCGIRCLK is trimmed, programming low reference divider (RDIV) factors may result in MCGOUT frequencies that exceed the maximum chip-level frequency and violate the chip-level clock timing specifications (see the Device Overview chapter). If IREFSTEN and IRCLKEN bits are both set, the internal reference clock will keep running during stop mode in order to provide a fast recovery upon exiting stop. 12.4.6 External Reference Clock The MCG module can support an external reference clock with frequencies between 31.25 kHz to 5 MHz in FEE and FBE modes, 1 MHz to 16 MHz in PEE and PBE modes, and 0 to 40 MHz in BLPE mode. When ERCLKEN is set, the external reference clock signal will be presented as MCGERCLK, which can be used as an additional clock source. When IREFS = 1, the external reference clock will not be used by the FLL or PLL and will only be used as MCGERCLK. In these modes, the frequency can be equal to the maximum frequency the chip-level timing specifications will support (see the Device Overview chapter). If EREFSTEN and ERCLKEN bits are both set or the MCG is in FEE, FBE, PEE, PBE or BLPE mode, the external reference clock will keep running during stop mode in order to provide a fast recovery upon exiting stop. If CME bit is written to 1, the clock monitor is enabled. If the external reference falls below a certain frequency (f or f depending on the RANGE bit in the MCGC2), the MCU will reset. The loc_high loc_low LOC bit in the System Reset Status (SRS) register will be set to indicate the error. 12.4.7 Fixed Frequency Clock The MCG presents the divided reference clock as MCGFFCLK for use as an additional clock source. The MCGFFCLK frequency must be no more than 1/4 of the MCGOUT frequency to be valid. Because of this requirement, the MCGFFCLK is not valid in bypass modes for the following combinations of BDIV and RDIV values: MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 195

Multi-Purpose Clock Generator (S08MCGV1) • BDIV=00 (divide by 1), RDIV < 010 BDIV=01 (divide by 2), RDIV < 011 12.5 Initialization / Application Information This section describes how to initialize and configure the MCG module in application. The following sections include examples on how to initialize the MCG and properly switch between the various available modes. 12.5.1 MCG Module Initialization Sequence The MCG comes out of reset configured for FEI mode with the BDIV set for divide-by-2. The internal reference will stabilize in t microseconds before the FLL can acquire lock. As soon as the internal irefst reference is stable, the FLL will acquire lock in t milliseconds. fll_lock Upon POR, the internal reference will require trimming to guarantee an accurate clock. Freescale recommends using FLASH location 0xFFAE for storing the fine trim bit, FTRIM in the MCGSC register, and 0xFFAF for storing the 8-bit trim value in the MCGTRM register. The MCU will not automatically copy the values in these FLASH locations to the respective registers. Therefore, user code must copy these values from FLASH to the registers. NOTE The BDIV value should not be changed to divide-by-1 without first trimming the internal reference. Failure to do so could result in the MCU running out of specification. 12.5.1.1 Initializing the MCG Because the MCG comes out of reset in FEI mode, the only MCG modes which can be directly switched to upon reset are FEE, FBE, and FBI modes (see Figure12-8). Reaching any of the other modes requires first configuring the MCG for one of these three initial modes. Care must be taken to check relevant status bits in the MCGSC register reflecting all configuration changes within each mode. To change from FEI mode to FEE or FBE modes, follow this procedure: 1. Enable the external clock source by setting the appropriate bits in MCGC2. 2. Write to MCGC1 to select the clock mode. — If entering FEE, set RDIV appropriately, clear the IREFS bit to switch to the external reference, and leave the CLKS bits at %00 so that the output of the FLL is selected as the system clock source. — If entering FBE, clear the IREFS bit to switch to the external reference and change the CLKS bits to %10 so that the external reference clock is selected as the system clock source. The RDIV bits should also be set appropriately here according to the external reference frequency because although the FLL is bypassed, it is still on in FBE mode. — The internal reference can optionally be kept running by setting the IRCLKEN bit. This is useful if the application will switch back and forth between internal and external modes. For MC9S08JM60 Series Data Sheet, Rev. 5 196 Freescale Semiconductor

Multi-Purpose Clock Generator (S08MCGV1) minimum power consumption, leave the internal reference disabled while in an external clock mode. 3. After the proper configuration bits have been set, wait for the affected bits in the MCGSC register to be changed appropriately, reflecting that the MCG has moved into the proper mode. — If ERCLKEN was set in step 1 or the MCG is in FEE, FBE, PEE, PBE, or BLPE mode, and EREFS was also set in step 1, wait here for the OSCINIT bit to become set indicating that the external clock source has finished its initialization cycles and stabilized. Typical crystal startup times are given in Appendix A, “Electrical Characteristics”. — If in FEE mode, check to make sure the IREFST bit is cleared and the LOCK bit is set before moving on. — If in FBE mode, check to make sure the IREFST bit is cleared, the LOCK bit is set, and the CLKST bits have changed to %10 indicating the external reference clock has been appropriately selected. Although the FLL is bypassed in FBE mode, it is still on and will lock in FBE mode. To change from FEI clock mode to FBI clock mode, follow this procedure: 1. Change the CLKS bits to %01 so that the internal reference clock is selected as the system clock source. 2. Wait for the CLKST bits in the MCGSC register to change to %01, indicating that the internal reference clock has been appropriately selected. 12.5.2 MCG Mode Switching When switching between operational modes of the MCG, certain configuration bits must be changed in order to properly move from one mode to another. Each time any of these bits are changed (PLLS, IREFS, CLKS, or EREFS), the corresponding bits in the MCGSC register (PLLST, IREFST, CLKST, or OSCINIT) must be checked before moving on in the application software. Additionally, care must be taken to ensure that the reference clock divider (RDIV) is set properly for the mode being switched to. For instance, in PEE mode, if using a 4 MHz crystal, RDIV must be set to %001 (divide-by-2) or %010 (divide -by-4) in order to divide the external reference down to the required frequency between 1 and 2 MHz. The RDIV and IREFS bits should always be set properly before changing the PLLS bit so that the FLL or PLL clock has an appropriate reference clock frequency to switch to. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 197

Multi-Purpose Clock Generator (S08MCGV1) The table below shows MCGOUT frequency calculations using RDIV, BDIV, and VDIV settings for each clock mode. The bus frequency is equal to MCGOUT divided by 2. Table12-6. MCGOUT Frequency Calculation Options Clock Mode f 1 Note MCGOUT FEI (FLL engaged internal) (f * 1024) / B Typical f = 16 MHz int MCGOUT immediately after reset. RDIV bits set to %000. FEE (FLL engaged external) (f / R *1024) / B f / R must be in the range of ext ext 31.25 kHz to 39.0625 kHz FBE (FLL bypassed external) f / B f / R must be in the range of ext ext 31.25 kHz to 39.0625 kHz FBI (FLL bypassed internal) f / B Typical f = 32 kHz int int PEE (PLL engaged external) [(f / R) * M] / B f / R must be in the range of 1 ext ext MHz to 2 MHz PBE (PLL bypassed external) f / B f / R must be in the range of 1 ext ext MHz to 2 MHz BLPI (Bypassed low power internal) f / B int BLPE (Bypassed low power external) f / B ext 1R is the reference divider selected by the RDIV bits, B is the bus frequency divider selected by the BDIV bits, and M is the multiplier selected by the VDIV bits. This section will include 3 mode switching examples using a 4 MHz external crystal. If using an external clock source less than 1 MHz, the MCG should not be configured for any of the PLL modes (PEE and PBE). 12.5.2.1 Example # 1: Moving from FEI to PEE Mode: External Crystal = 4 MHz, Bus Frequency = 8 MHz In this example, the MCG will move through the proper operational modes from FEI to PEE mode until the 4 MHz crystal reference frequency is set to achieve a bus frequency of 8 MHz. Because the MCG is in FEI mode out of reset, this example also shows how to initialize the MCG for PEE mode out of reset. First, the code sequence will be described. Then a flowchart will be included which illustrates the sequence. 1. First, FEI must transition to FBE mode: a) MCGC2 = 0x36 (%00110110) – BDIV (bits 7 and 6) set to %00, or divide-by-1 – RANGE (bit 5) set to 1 because the frequency of 4 MHz is within the high frequency range – HGO (bit 4) set to 1 to configure external oscillator for high gain operation – EREFS (bit 2) set to 1, because a crystal is being used – ERCLKEN (bit 1) set to 1 to ensure the external reference clock is active b) Loop until OSCINIT (bit 1) in MCGSC is 1, indicating the crystal selected by the EREFS bit has been initialized. MC9S08JM60 Series Data Sheet, Rev. 5 198 Freescale Semiconductor

Multi-Purpose Clock Generator (S08MCGV1) c) MCGC1 = 0xB8 (%10111000) – CLKS (bits 7 and 6) set to %10 in order to select external reference clock as system clock source – RDIV (bits 5-3) set to %111, or divide-by-128 because 4 MHz / 128 = 31.25 kHz which is in the 31.25 kHz to 39.0625 kHz range required by the FLL – IREFS (bit 2) cleared to 0, selecting the external reference clock d) Loop until IREFST (bit 4) in MCGSC is 0, indicating the external reference is the current source for the reference clock e) Loop until CLKST (bits 3 and 2) in MCGSC are %10, indicating that the external reference clock is selected to feed MCGOUT 2. Then, FBE must transition either directly to PBE mode or first through BLPE mode and then to PBE mode: a) BLPE: If a transition through BLPE mode is desired, first set LP (bit 3) in MCGC2 to 1. b) BLPE/PBE: MCGC1 = 0x90 (%10010000) – RDIV (bits 5-3) set to %010, or divide-by-4 because 4 MHz / 4 = 1 MHz which is in the 1 MHz to 2 MHz range required by the PLL. In BLPE mode, the configuration of the RDIV does not matter because both the FLL and PLL are disabled. Changing them only sets up the the dividers for PLL usage in PBE mode c) BLPE/PBE: MCGC3 = 0x44 (%01000100) – PLLS (bit 6) set to 1, selects the PLL. In BLPE mode, changing this bit only prepares the MCG for PLL usage in PBE mode – VDIV (bits 3-0) set to %0100, or multiply-by-16 because 1 MHz reference * 16 = 16 MHz. In BLPE mode, the configuration of the VDIV bits does not matter because the PLL is disabled. Changing them only sets up the multiply value for PLL usage in PBE mode d) BLPE: If transitioning through BLPE mode, clear LP (bit 3) in MCGC2 to 0 here to switch to PBE mode e) PBE: Loop until PLLST (bit 5) in MCGSC is set, indicating that the current source for the PLLS clock is the PLL f) PBE: Then loop until LOCK (bit 6) in MCGSC is set, indicating that the PLL has acquired lock 3. Last, PBE mode transitions into PEE mode: a) MCGC1 = 0x10 (%00010000) – CLKS (bits7 and 6) in MCGSC1 set to %00 in order to select the output of the PLL as the system clock source – Loop until CLKST (bits 3 and 2) in MCGSC are %11, indicating that the PLL output is selected to feed MCGOUT in the current clock mode b) Now, With an RDIV of divide-by-4, a BDIV of divide-by-1, and a VDIV of multiply-by-16, MCGOUT = [(4 MHz / 4) * 16] / 1 = 16 MHz, and the bus frequency is MCGOUT / 2, or 8 MHz MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 199

Multi-Purpose Clock Generator (S08MCGV1) START IN FEI MODE MCGC2 = $36 IN NO BLPE MODE ? (LP=1) CHECK NO OSCINIT = 1 ? YES MCGC2 = $36 YES (LP = 0) MCGC1 = $B8 CHECK NO PLLST = 1? CHECK NO IREFST = 0? YES YES CHECK NO LOCK = 1? CHECK NO CLKST = %10? YES YES MCGC1 = $10 ENTER NO BLPE MODE ? CHECK NO CLKST = %11? YES YES MCGC2 = $3E (LP = 1) CONTINUE IN PEE MODE MCGC1 = $90 MCGC3 = $44 Figure12-9. Flowchart of FEI to PEE Mode Transition using a 4 MHz Crystal MC9S08JM60 Series Data Sheet, Rev. 5 200 Freescale Semiconductor

Multi-Purpose Clock Generator (S08MCGV1) 12.5.2.2 Example # 2: Moving from PEE to BLPI Mode: External Crystal = 4 MHz, Bus Frequency =16 kHz In this example, the MCG will move through the proper operational modes from PEE mode with a 4 MHz crystal configured for an 8 MHz bus frequency (see previous example) to BLPI mode with a 16 kHz bus frequency.First, the code sequence will be described. Then a flowchart will be included which illustrates the sequence. 1. First, PEE must transition to PBE mode: a) MCGC1 = 0x90 (%10010000) – CLKS (bits 7 and 6) set to %10 in order to switch the system clock source to the external reference clock b) Loop until CLKST (bits 3 and 2) in MCGSC are %10, indicating that the external reference clock is selected to feed MCGOUT 2. Then, PBE must transition either directly to FBE mode or first through BLPE mode and then to FBE mode: a) BLPE: If a transition through BLPE mode is desired, first set LP (bit 3) in MCGC2 to 1 b) BLPE/FBE: MCGC1 = 0xB8 (%10111000) – RDIV (bits 5-3) set to %111, or divide-by-128 because 4 MHz / 128 = 31.25 kHz which is in the 31.25 kHz to 39.0625 kHz range required by the FLL. In BLPE mode, the configuration of the RDIV does not matter because both the FLL and PLL are disabled. Changing them only sets up the dividers for FLL usage in FBE mode c) BLPE/FBE: MCGC3 = 0x04 (%00000100) – PLLS (bit 6) clear to 0 to select the FLL. In BLPE mode, changing this bit only prepares the MCG for FLL usage in FBE mode. With PLLS = 0, the VDIV value does not matter. d) BLPE: If transitioning through BLPE mode, clear LP (bit 3) in MCGC2 to 0 here to switch to FBE mode e) FBE: Loop until PLLST (bit 5) in MCGSC is clear, indicating that the current source for the PLLS clock is the FLL f) FBE: Optionally, loop until LOCK (bit 6) in the MCGSC is set, indicating that the FLL has acquired lock. Although the FLL is bypassed in FBE mode, it is still enabled and running. 3. Next, FBE mode transitions into FBI mode: a) MCGC1 = 0x44 (%01000100) – CLKS (bits7 and 6) in MCGSC1 set to %01 in order to switch the system clock to the internal reference clock – IREFS (bit 2) set to 1 to select the internal reference clock as the reference clock source – RDIV (bits 5-3) set to %000, or divide-by-1 because the trimmed internal reference should be within the 31.25 kHz to 39.0625 kHz range required by the FLL b) Loop until IREFST (bit 4) in MCGSC is 1, indicating the internal reference clock has been selected as the reference clock source c) Loop until CLKST (bits 3 and 2) in MCGSC are %01, indicating that the internal reference clock is selected to feed MCGOUT MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 201

Multi-Purpose Clock Generator (S08MCGV1) 4. Lastly, FBI transitions into FBILP mode. a) MCGC2 = 0x08 (%00001000) – LP (bit 3) in MCGSC is 1 START IN PEE MODE MCGC1 = $90 CHECK NO PLLST = 0? CHECK NO YES CLKST = %10 ? YES OPTIONAL: NO CHECK LOCK = 1? ENTER NO BLPE MODE ? YES MCGC1 = $44 YES MCGC2 = $3E CHECK NO IREFST = 0? MCGC1 = $B8 MCGC3 = $04 YES IN CHECK NO NO BLPE MODE ? CLKST = %01? (LP=1) YES YES MCGC2 = $08 MCGC2 = $36 (LP = 0) CONTINUE IN BLPI MODE Figure12-10. Flowchart of PEE to BLPI Mode Transition using a 4 MHz Crystal MC9S08JM60 Series Data Sheet, Rev. 5 202 Freescale Semiconductor

Multi-Purpose Clock Generator (S08MCGV1) 12.5.2.3 Example #3: Moving from BLPI to FEE Mode: External Crystal = 4 MHz, Bus Frequency = 16 MHz In this example, the MCG will move through the proper operational modes from BLPI mode at a 16 kHz bus frequency running off of the internal reference clock (see previous example) to FEE mode using a 4 MHz crystal configured for a 16 MHz bus frequency. First, the code sequence will be described. Then a flowchart will be included which illustrates the sequence. 1. First, BLPI must transition to FBI mode. a) MCGC2 = 0x00 (%00000000) – LP (bit 3) in MCGSC is 0 b) Optionally, loop until LOCK (bit 6) in the MCGSC is set, indicating that the FLL has acquired lock. Although the FLL is bypassed in FBI mode, it is still enabled and running. 2. Next, FBI will transition to FEE mode. a) MCGC2 = 0x36 (%00110110) – RANGE (bit 5) set to 1 because the frequency of 4 MHz is within the high frequency range – HGO (bit 4) set to 1 to configure external oscillator for high gain operation – EREFS (bit 2) set to 1, because a crystal is being used – ERCLKEN (bit 1) set to 1 to ensure the external reference clock is active b) Loop until OSCINIT (bit 1) in MCGSC is 1, indicating the crystal selected by the EREFS bit has been initialized. c) MCGC1 = 0x38 (%00111000) – CLKS (bits 7 and 6) set to %00 in order to select the output of the FLL as system clock source – RDIV (bits 5-3) set to %111, or divide-by-128 because 4 MHz / 128 = 31.25 kHz which is in the 31.25 kHz to 39.0625 kHz range required by the FLL – IREFS (bit 1) cleared to 0, selecting the external reference clock d) Loop until IREFST (bit 4) in MCGSC is 0, indicating the external reference clock is the current source for the reference clock e) Optionally, loop until LOCK (bit 6) in the MCGSC is set, indicating that the FLL has reacquired lock. f) Loop until CLKST (bits 3 and 2) in MCGSC are %00, indicating that the output of the FLL is selected to feed MCGOUT MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 203

Multi-Purpose Clock Generator (S08MCGV1) START IN BLPI MODE CHECK NO IREFST = 0? MCGC2 = $00 YES OPTIONAL: NO OPTIONAL: NO CHECK LOCK CHECK LOCK = 1? = 1? YES YES MCGC2 = $36 CHECK NO CLKST = %00? CHECK NO YES OSCINIT = 1 ? CONTINUE YES IN FEE MODE MCGC1 = $38 Figure12-11. Flowchart of BLPI to FEE Mode Transition using a 4 MHz Crystal 12.5.2.4 Example # 4: Moving from FEI to PEE Mode: External Crystal = 8 MHz, Bus Frequency = 8 MHz In this example, the MCG will move through the proper operational modes from FEI to PEE mode until the 8 MHz crystal reference frequency is set to achieve a bus frequency of 8 MHz. This example is similar to example number one except that in this case the frequency of the external crystal is 8 MHz instead of 4 MHz. Special consideration must be taken with this case since there is a period of time along the way from FEI mode to PEE mode where the FLL operates based on a reference clock with a frequency that is greater than the maximum allowed for the FLL. This occurs because with an 8 MHz MC9S08JM60 Series Data Sheet, Rev. 5 204 Freescale Semiconductor

Multi-Purpose Clock Generator (S08MCGV1) external crystal and a maximum reference divider factor of 128, the resulting frequency of the reference clock for the FLL is 62.5 kHz (greater than the 39.0625 kHz maximum allowed). Care must be taken in the software to minimize the amount of time spent in this state where the FLL is operating in this condition. The following code sequence describes how to move from FEI mode to PEE mode until the 8 MHz crystal reference frequency is set to achieve a bus frequency of 8 MHz. Because the MCG is in FEI mode out of reset, this example also shows how to initialize the MCG for PEE mode out of reset. First, the code sequence will be described. Then a flowchart will be included which illustrates the sequence. 1. First, FEI must transition to FBE mode: a) MCGC2 = 0x36 (%00110110) – BDIV (bits 7 and 6) set to %00, or divide-by-1 – RANGE (bit 5) set to 1 because the frequency of 8 MHz is within the high frequency range – HGO (bit 4) set to 1 to configure external oscillator for high gain operation – EREFS (bit 2) set to 1, because a crystal is being used – ERCLKEN (bit 1) set to 1 to ensure the external reference clock is active b) Loop until OSCINIT (bit 1) in MCGSC is 1, indicating the crystal selected by the EREFS bit has been initialized. c) Block Interrupts (If applicable by setting the interrupt bit in the CCR). d) MCGC1 = 0xB8 (%10111000) – CLKS (bits 7 and 6) set to %10 in order to select external reference clock as system clock source – RDIV (bits 5-3) set to %111, or divide-by-128. NOTE 8 MHz / 128 = 62.5 kHz which is greater than the 31.25 kHz to 39.0625 kHz range required by the FLL. Therefore after the transition to FBE is complete, software must progress through to BLPE mode immediately by setting the LP bit in MCGC2. – IREFS (bit 2) cleared to 0, selecting the external reference clock e) Loop until IREFST (bit 4) in MCGSC is 0, indicating the external reference is the current source for the reference clock f) Loop until CLKST (bits 3 and 2) in MCGSC are %10, indicating that the external reference clock is selected to feed MCGOUT 2. Then, FBE mode transitions into BLPE mode: a) MCGC2 = 0x3E (%00111110) – LP (bit 3) in MCGC2 to 1 (BLPE mode entered) NOTE There must be no extra steps (including interrupts) between steps 1d and 2a. b) Enable Interrupts (if applicable by clearing the interrupt bit in the CCR). MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 205

Multi-Purpose Clock Generator (S08MCGV1) c) MCGC1 = 0x98 (%10011000) – RDIV (bits 5-3) set to %011, or divide-by-8 because 8 MHz / 8= 1 MHz which is in the 1 MHz to 2 MHz range required by the PLL. In BLPE mode, the configuration of the RDIV does not matter because both the FLL and PLL are disabled. Changing them only sets up the the dividers for PLL usage in PBE mode d) MCGC3 = 0x44 (%01000100) – PLLS (bit 6) set to 1, selects the PLL. In BLPE mode, changing this bit only prepares the MCG for PLL usage in PBE mode – VDIV (bits 3-0) set to %0100, or multiply-by-16 because 1 MHz reference * 16 = 16 MHz. In BLPE mode, the configuration of the VDIV bits does not matter because the PLL is disabled. Changing them only sets up the multiply value for PLL usage in PBE mode e) Loop until PLLST (bit 5) in MCGSC is set, indicating that the current source for the PLLS clock is the PLL 3. Then, BLPE mode transitions into PBE mode: a) Clear LP (bit 3) in MCGC2 to 0 here to switch to PBE mode b) Then loop until LOCK (bit 6) in MCGSC is set, indicating that the PLL has acquired lock 4. Last, PBE mode transitions into PEE mode: a) MCGC1 = 0x18 (%00011000) – CLKS (bits7 and 6) in MCGSC1 set to %00 in order to select the output of the PLL as the system clock source – Loop until CLKST (bits 3 and 2) in MCGSC are %11, indicating that the PLL output is selected to feed MCGOUT in the current clock mode b) Now, With an RDIV of divide-by-8, a BDIV of divide-by-1, and a VDIV of multiply-by-16, MCGOUT = [(8 MHz / 8) * 16] / 1 = 16 MHz, and the bus frequency is MCGOUT / 2, or 8 MHz MC9S08JM60 Series Data Sheet, Rev. 5 206 Freescale Semiconductor

Multi-Purpose Clock Generator (S08MCGV1) START IN FEI MODE MCGC2 = $36 CHECK NO CHECK NO PLLST = 1? OSCINIT = 1 ? YES YES MCGC2 = $36 (LP = 0) MCGC1 = $B8 CHECK NO IREFST = 0? CHECK NO LOCK = 1? YES YES CHECK NO MCGC1 = $18 CLKST = %10? YES CHECK NO MCGC2 = $3E CLKST = %11? (LP = 1) YES MCGC1 = $98 MCGC3 = $44 CONTINUE IN PEE MODE Figure12-12. Flowchart of FEI to PEE Mode Transition using a 8 MHz Crystal MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 207

Multi-Purpose Clock Generator (S08MCGV1) 12.5.3 Calibrating the Internal Reference Clock (IRC) The IRC is calibrated by writing to the MCGTRM register first, then using the FTRIM bit to “fine tune” the frequency. We will refer to this total 9-bit value as the trim value, ranging from 0x000 to 0x1FF, where the FTRIM bit is the LSB. The trim value after a POR is always 0x100 (MCGTRM = 0x80 and FTRIM = 0). Writing a larger value will decrease the frequency and smaller values will increase the frequency. The trim value is linear with the period, except that slight variations in wafer fab processing produce slight non-linearities between trim value and period. These non-linearities are why an iterative trimming approach to search for the best trim value is recommended. In example #4 later in this section, this approach will be demonstrated. After a trim value has been found for a device, this value can be stored in FLASH memory to save the value. If power is removed from the device, the IRC can easily be re-trimmed by copying the saved value from FLASH to the MCG registers. Freescale identifies recommended FLASH locations for storing the trim value for each MCU. Consult the memory map in the data sheet for these locations. On devices that are factory trimmed, the factory trim value will be stored in these locations. 12.5.3.1 Example #5: Internal Reference Clock Trim For applications that require a tight frequency tolerance, a trimming procedure is provided that will allow a very accurate internal clock source. This section outlines one example of trimming the internal oscillator. Many other possible trimming procedures are valid and can be used. In the example below, the MCG trim will be calibrated for the 9-bit MCGTRM and FTRIM collective value. This value will be referred to as TRMVAL. MC9S08JM60 Series Data Sheet, Rev. 5 208 Freescale Semiconductor

Multi-Purpose Clock Generator (S08MCGV1) Initial conditions: 1) Clock supplied from ATE has 500 μs duty period 2) MCG configured for internal reference with 8MHz bus START TRIM PROCEDURE TRMVAL = $100 n=1 MEASURE INCOMING CLOCK WIDTH (COUNT = # OF BUS CLOCKS / 8) COUNT < EXPECTED =500 (RUNNING TOO SLOW) . COUNT = EXPECTED = 500 CASE STATEMENT COUNT > EXPECTED = 500 (RUNNING TOO FAST) TRMVAL = TRMVAL = STORE MCGTRM AND TRMVAL - 256/ (2**n) TRMVAL + 256/ (2**n) (DECREASIN G TRMVAL (INCREASIN G TRMVAL FTRIM VAL UES IN NON-VOLATILE MEMORY INCREASES THE FREQUENCY) DECREASES THE FREQUENCY) CONTINUE n = n + 1 YES IS n > 9? NO Figure12-13. Trim Procedure In this particular case, the MCU has been attached to a PCB and the entire assembly is undergoing final test with automated test equipment. A separate signal or message is provided to the MCU operating under user provided software control. The MCU initiates a trim procedure as outlined in Figure 12-13 while the tester supplies a precision reference signal. If the intended bus frequency is near the maximum allowed for the device, it is recommended to trim using a reference divider value (RDIV setting) of twice the final value. After the trim procedure is complete, the reference divider can be restored. This will prevent accidental overshoot of the maximum clock frequency. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 209

Multi-Purpose Clock Generator (S08MCGV1) MC9S08JM60 Series Data Sheet, Rev. 5 210 Freescale Semiconductor

Chapter 13 Real-Time Counter (S08RTCV1) 13.1 Introduction The real-time counter (RTC) consists of one 8-bit counter, one 8-bit comparator, several binary-based and decimal-based prescaler dividers, two clock sources, and one programmable periodic interrupt. This module can be used for time-of-day, calendar or any task scheduling functions. It can also serve as a cyclic wake up from low power modes without the need of external components. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 211

Chapter13 Real-Time Counter (S08RTCV1) USBDP ON-CHIP ICE AND USBDN HCS08 CORE DEBUG MODULE (DBG) A T 6 R PTA5– PTA0 O USB SIE P BKGD/MS FULL SPEED PTB7/ADP7 BDC CPU USB PTB6/ADP6 USB ENDPOINT TRANSCEIVER PTB5/KBIP5/ADP5 RAM B T PTB4/KBIP4/ADP4 SSPSS2CK2 POR PTB3/SS2/ADP3 RESET HCS08 SYSTEM CONTROL 8-/16-BIT SERIAL PERIPHERAL MOSI2 PTB2/SPSCK2/ADP2 INTERFACE MODULE (SPI2) PTB1/MOSI2/ADP1 MISO2 PTB0/MISO2/ADP0 RESETS AND INTERRUPTS MODES OF OPERATION PTC6 IRQ/TPMCLK POWER MANAGEMENT SERIAL COMMUNICATIONS RxD2 PTC5/RxD2 COP IRQ LVD INTERFACE MODULE (SCI2) TxD2 ORT C PPTTCC34/TxD2 P PTC2 SDA PTC1/SDA IIC MODULE (IIC) SCL PTC0/SCL VDDAD 12-CHANNEL, 12-BIT 8 PTD7 VSSAD ANALOG-TO-DIGITAL 4 PTD6 VREFL CONVERTER (ADC) PTD5 VREFH D PTD4/ADP11 T R PTD3/KBIP3/ADP10 O USER Flash (IN BYTES) P PTD2/KBIP2/ACMPO ACMP– MC9S08JM60 = 60,912 PTD1/ADP9/ACMP– MC9S08JM32 = 32,768 ANALOG COMPARATOR ACMP+ PTD0/ADP8/ACMP+ (ACMP) ACMPO SS1 PTE7/SS1 USER RAM (IN BYTES) SPSCK1 8-/16-BIT SERIAL PERIPHERAL PTE6/SPSCK1 MMCC99SS0088JJMM6302 == 42009468 INTERFACE MODULE (SPI1) MOSI1 PTE5/MOSI1 MISO1 PTE4/MISO1 TPMCLK E MULTI-PURPOSE CLOCK 6-CHMAONDNUELLE T (IMTPEMR1/P)WM TTPPMM11CCHH10 PORT PTE3/TPM1CH1 GENERATOR (MCG) PTE2/TPM1CH0 TPM1CHx4 RxD1 SERIAL COMMUNICATIONS PTE1/RxD1 VSSOSC LOW-POWER OSCILLATOR TxD1 PTE0/TxD1 INTERFACE MODULE (SCI1) PTF7 VDD SYSTEM TPMCLK PTF6 VSS RVEOGLUTLAAGTEO R 2-CHMAONDNUELLE T (IMTPEMR2/P)WM TTPPMM22CCHH10 T F PPTTFF54//TTPPMM22CCHH10 OR PTF3/TPM1CH5 KBIPx P PTF2/TPM1CH4 VUSB33 USB 3.3-V VOLTAGE REGULATOR 8-BIT KEYBOARD 4 PTF1/TPM1CH3 INTERRUPT MODULE (KBI) KBIPx 4 PTF0/TPM1CH2 REAL-TIME COUNTER (RTC) EXTAL PTG5/EXTAL XTAL NOTES: G PTG4/XTAL 1. Port pins are software configurable with pullup device if input port. RT PTG3/KBIP7 O PTG2/KBIP6 2. Pin contains software configurable pullup/pull-down device if IRQ is enabled P PTG1/KBIP1 (IRQPE=1). Pull-down is enabled if rising edge detect is selected (IRQEDG=1) PTG0/KBIP0 3. IRQ does not have a clamp diode to V . IRQ must not be driven above V . DD DD 4. Pin contains integrated pullup device. 5. When pin functions as KBI (KBIPEn = 1) and associated pin is configured to enable the pullup device, KBEDGn can be used to reconfigure the pullup as a pull-down device. Figure13-1. MC9S08JM60 Series Block Diagram Highlighting RTC Block MC9S08JM60 Series Data Sheet, Rev. 5 212 Freescale Semiconductor

Real-Time Counter (S08RTCV1) 13.1.1 Features Features of the RTC module include: • 8-bit up-counter — 8-bit modulo match limit — Software controllable periodic interrupt on match • Three software selectable clock sources for input to prescaler with selectable binary-based and decimal-based divider values — 1 kHz internal low-power oscillator (LPO) — External clock (ERCLK) — 32 kHz internal clock (IRCLK) 13.1.2 Modes of Operation This section defines the operation in stop, wait and background debug modes. 13.1.2.1 Wait Mode The RTC continues to run in wait mode if enabled before executing the appropriate instruction. Therefore, the RTC can bring the MCU out of wait mode if the real-time interrupt is enabled. For lowest possible current consumption, the RTC should be stopped by software if not needed as an interrupt source during wait mode. 13.1.2.2 Stop Modes The RTC continues to run in stop2 or stop3 mode if the RTC is enabled before executing the STOP instruction. Therefore, the RTC can bring the MCU out of stop modes with no external components, if the real-time interrupt is enabled. The LPO clock can be used in stop2 and stop3 modes. ERCLK and IRCLK clocks are only available in stop3 mode. Power consumption is lower when all clock sources are disabled, but in that case, the real-time interrupt cannot wake up the MCU from stop modes. 13.1.2.3 Active Background Mode The RTC suspends all counting during active background mode until the microcontroller returns to normal user operating mode. Counting resumes from the suspended value as long as the RTCMOD register is not written and the RTCPS and RTCLKS bits are not altered. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 213

Real-Time Counter (S08RTCV1) 13.1.3 Block Diagram The block diagram for the RTC module is shown in Figure 13-2. LPO Clock Source ERCLK Select IRCLK V 8-Bit Modulo DD (RTCMOD) RTCLKS Background D Q RTIF RTC Mode Interrupt Request RTCLKS[0] RTCPS 8-Bit Comparator E R RTC RTIE Write 1 to Prescaler Clock 8-Bit Counter RTIF Divide-By (RTCCNT) Figure13-2. Real-Time Counter (RTC) Block Diagram 13.2 External Signal Description The RTC does not include any off-chip signals. 13.3 Register Definition The RTC includes a status and control register, an 8-bit counter register, and an 8-bit modulo register. Refer to the direct-page register summary in the memory section of this document for the absolute address assignments for all RTC registers.This section refers to registers and control bits only by their names and relative address offsets. Table 13-1 is a summary of RTC registers. Table13-1. RTC Register Summary Name 7 6 5 4 3 2 1 0 R RTCSC RTIF RTCLKS RTIE RTCPS W R RTCCNT RTCCNT W R RTCMOD RTCMOD W MC9S08JM60 Series Data Sheet, Rev. 5 214 Freescale Semiconductor

Real-Time Counter (S08RTCV1) 13.3.1 RTC Status and Control Register (RTCSC) RTCSC contains the real-time interrupt status flag (RTIF), the clock select bits (RTCLKS), the real-time interrupt enable bit (RTIE), and the prescaler select bits (RTCPS). 7 6 5 4 3 2 1 0 R RTIF RTCLKS RTIE RTCPS W Reset: 0 0 0 0 0 0 0 0 Figure13-3. RTC Status and Control Register (RTCSC) Table13-2. RTCSC Field Descriptions Field Description 7 Real-Time Interrupt Flag This status bit indicates the RTC counter register reached the value in the RTC modulo RTIF register. Writing a logic 0 has no effect. Writing a logic 1 clears the bit and the real-time interrupt request. Reset clears RTIF. 0 RTC counter has not reached the value in the RTC modulo register. 1 RTC counter has reached the value in the RTC modulo register. 6–5 Real-Time Clock Source Select. These two read/write bits select the clock source input to the RTC prescaler. RTCLKS Changing the clock source clears the prescaler and RTCCNT counters. When selecting a clock source, ensure that the clock source is properly enabled (if applicable) to ensure correct operation of the RTC. Reset clears RTCLKS. 00 Real-time clock source is the 1-kHz low power oscillator (LPO) 01 Real-time clock source is the external clock (ERCLK) 1x Real-time clock source is the internal clock (IRCLK) 4 Real-Time Interrupt Enable. This read/write bit enables real-time interrupts. If RTIE is set, then an interrupt is RTIE generated when RTIF is set. Reset clears RTIE. 0 Real-time interrupt requests are disabled. Use software polling. 1 Real-time interrupt requests are enabled. 3–0 Real-Time Clock Prescaler Select. These four read/write bits select binary-based or decimal-based divide-by RTCPS values for the clock source. See Table13-3. Changing the prescaler value clears the prescaler and RTCCNT counters. Reset clears RTCPS. Table13-3. RTC Prescaler Divide-by values RTCPS RTCLKS[0] 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 0 Off 23 25 26 27 28 29 210 1 2 22 10 24 102 5x102 103 1 Off 210 211 212 213 214 215 216 103 2x103 5x103 104 2x104 5x104 105 2x105 MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 215

Real-Time Counter (S08RTCV1) 13.3.2 RTC Counter Register (RTCCNT) RTCCNT is the read-only value of the current RTC count of the 8-bit counter. 7 6 5 4 3 2 1 0 R RTCCNT W Reset: 0 0 0 0 0 0 0 0 Figure13-4. RTC Counter Register (RTCCNT) Table13-4. RTCCNT Field Descriptions Field Description 7:0 RTC Count. These eight read-only bits contain the current value of the 8-bit counter. Writes have no effect to this RTCCNT register. Reset, writing to RTCMOD, or writing different values to RTCLKS and RTCPS clear the count to 0x00. 13.3.3 RTC Modulo Register (RTCMOD) 7 6 5 4 3 2 1 0 R RTCMOD W Reset: 0 0 0 0 0 0 0 0 Figure13-5. RTC Modulo Register (RTCMOD) Table13-5. RTCMOD Field Descriptions Field Description 7:0 RTC Modulo. These eight read/write bits contain the modulo value used to reset the count to 0x00 upon a compare RTCMOD match and set the RTIF status bit. A value of 0x00 sets the RTIF bit on each rising edge of the prescaler output. Writing to RTCMOD resets the prescaler and the RTCCNT counters to 0x00. Reset sets the modulo to 0x00. 13.4 Functional Description The RTC is composed of a main 8-bit up-counter with an 8-bit modulo register, a clock source selector, and a prescaler block with binary-based and decimal-based selectable values. The module also contains software selectable interrupt logic. After any MCU reset, the counter is stopped and reset to 0x00, the modulus register is set to 0x00, and the prescaler is off. The 1-kHz internal oscillator clock is selected as the default clock source. To start the prescaler, write any value other than zero to the prescaler select bits (RTCPS). Three clock sources are software selectable: the low power oscillator clock (LPO), the external clock (ERCLK), and the internal clock (IRCLK). The RTC clock select bits (RTCLKS) select the desired clock source. If a different value is written to RTCLKS, the prescaler and RTCCNT counters are reset to 0x00. MC9S08JM60 Series Data Sheet, Rev. 5 216 Freescale Semiconductor

Real-Time Counter (S08RTCV1) RTCPS and the RTCLKS[0] bit select the desired divide-by value. If a different value is written to RTCPS, the prescaler and RTCCNT counters are reset to 0x00. Table 13-6 shows different prescaler period values. Table13-6. Prescaler Period 1-kHz Internal Clock 1-MHz External Clock 32-kHz Internal Clock 32-kHz Internal Clock RTCPS (RTCLKS = 00) (RTCLKS = 01) (RTCLKS = 10) (RTCLKS = 11) 0000 Off Off Off Off 0001 8 ms 1.024 ms 250 μs 32 ms 0010 32 ms 2.048 ms 1 ms 64 ms 0011 64 ms 4.096 ms 2 ms 128 ms 0100 128 ms 8.192 ms 4 ms 256 ms 0101 256 ms 16.4 ms 8 ms 512 ms 0110 512 ms 32.8 ms 16 ms 1.024 s 0111 1.024 s 65.5 ms 32 ms 2.048 s 1000 1 ms 1 ms 31.25 μs 31.25 ms 1001 2 ms 2 ms 62.5 μs 62.5 ms 1010 4 ms 5 ms 125 μs 156.25 ms 1011 10 ms 10 ms 312.5 μs 312.5 ms 1100 16 ms 20 ms 0.5 ms 0.625 s 1101 0.1 s 50 ms 3.125 ms 1.5625 s 1110 0.5 s 0.1 s 15.625 ms 3.125 s 1111 1 s 0.2 s 31.25 ms 6.25 s The RTC modulo register (RTCMOD) allows the compare value to be set to any value from 0x00 to 0xFF. When the counter is active, the counter increments at the selected rate until the count matches the modulo value. When these values match, the counter resets to 0x00 and continues counting. The real-time interrupt flag (RTIF) is set when a match occurs. The flag sets on the transition from the modulo value to 0x00. Writing to RTCMOD resets the prescaler and the RTCCNT counters to 0x00. The RTC allows for an interrupt to be generated when RTIF is set. To enable the real-time interrupt, set the real-time interrupt enable bit (RTIE) in RTCSC. RTIF is cleared by writing a 1 to RTIF. 13.4.1 RTC Operation Example This section shows an example of the RTC operation as the counter reaches a matching value from the modulo register. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 217

Real-Time Counter (S08RTCV1) Internal 1-kHz Clock Source RTC Clock (RTCPS=0xA) RTCCNT 0x52 0x53 0x54 0x55 0x00 0x01 RTIF RTCMOD 0x55 Figure13-6. RTC Counter Overflow Example In the example of Figure 13-6, the selected clock source is the 1-kHz internal oscillator clock source. The prescaler (RTCPS) is set to 0xA or divide-by-4. The modulo value in the RTCMOD register is set to 0x55. When the counter, RTCCNT, reaches the modulo value of 0x55, the counter overflows to 0x00 and continues counting. The real-time interrupt flag, RTIF, sets when the counter value changes from 0x55 to 0x00. A real-time interrupt is generated when RTIF is set, if RTIE is set. 13.5 Initialization/Application Information This section provides example code to give some basic direction to a user on how to initialize and configure the RTC module. The example software is implemented in C language. The example below shows how to implement time of day with the RTC using the 1-kHz clock source to achieve the lowest possible power consumption. Because the 1-kHz clock source is not as accurate as a crystal, software can be added for any adjustments. For accuracy without adjustments at the expense of additional power consumption, the external clock (ERCLK) or the internal clock (IRCLK) can be selected with appropriate prescaler and modulo values. /* Initialize the elapsed time counters */ Seconds = 0; Minutes = 0; Hours = 0; Days=0; /* Configure RTC to interrupt every 1 second from 1-kHz clock source */ RTCMOD.byte = 0x00; RTCSC.byte = 0x1F; /********************************************************************** Function Name : RTC_ISR Notes : Interrupt service routine for RTC module. **********************************************************************/ #pragma TRAP_PROC void RTC_ISR(void) { /* Clear the interrupt flag */ MC9S08JM60 Series Data Sheet, Rev. 5 218 Freescale Semiconductor

Real-Time Counter (S08RTCV1) RTCSC.byte = RTCSC.byte | 0x80; /* RTC interrupts every 1 Second */ Seconds++; /* 60 seconds in a minute */ if (Seconds > 59){ Minutes++; Seconds = 0; } /* 60 minutes in an hour */ if (Minutes > 59){ Hours++; Minutes = 0; } /* 24 hours in a day */ if (Hours > 23){ Days ++; Hours = 0; } MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 219

Real-Time Counter (S08RTCV1) MC9S08JM60 Series Data Sheet, Rev. 5 220 Freescale Semiconductor

Chapter 14 Serial Communications Interface (S08SCIV4) 14.1 Introduction The MC9S08JM60 series include two independent serial communications interface (SCI) modules which are sometimes called universal asynchronous receiver/transmitters (UARTs). Typically, these systems are used to connect to the RS232 serial input/output (I/O) port of a personal computer or workstation, but they can also be used to communicate with other embedded controllers. A flexible, 13-bit, modulo-based baud rate generator supports a broad range of standard baud rates beyond 115.2 kbaud. Transmit and receive within the same SCI use a common baud rate, and each SCI module has a separate baud rate generator. This SCI system offers many advanced features not commonly found on other asynchronous serial I/O peripherals on other embedded controllers. The receiver employs an advanced data sampling technique that ensures reliable communication and noise detection. Hardware parity, receiver wakeup, and double buffering on transmit and receive are also included. NOTE MC9S08JM60 series devices operate at a higher voltage range (2.7 V to 5.5V) and do not include stop1 mode. Therefore, please disregard references to stop1. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 221

Chapter14 Serial Communications Interface (S08SCIV4) USBDP ON-CHIP ICE AND USBDN HCS08 CORE DEBUG MODULE (DBG) A T 6 R PTA5– PTA0 O USB SIE P BKGD/MS FULL SPEED PTB7/ADP7 BDC CPU USB PTB6/ADP6 USB ENDPOINT TRANSCEIVER PTB5/KBIP5/ADP5 RAM B T PTB4/KBIP4/ADP4 SSPSS2CK2 POR PTB3/SS2/ADP3 RESET HCS08 SYSTEM CONTROL 8-/16-BIT SERIAL PERIPHERAL MOSI2 PTB2/SPSCK2/ADP2 INTERFACE MODULE (SPI2) PTB1/MOSI2/ADP1 MISO2 PTB0/MISO2/ADP0 RESETS AND INTERRUPTS MODES OF OPERATION PTC6 IRQ/TPMCLK POWER MANAGEMENT SERIAL COMMUNICATIONS RxD2 PTC5/RxD2 COP IRQ LVD INTERFACE MODULE (SCI2) TxD2 ORT C PPTTCC34/TxD2 P PTC2 SDA PTC1/SDA IIC MODULE (IIC) SCL PTC0/SCL VDDAD 12-CHANNEL, 12-BIT 8 PTD7 VSSAD ANALOG-TO-DIGITAL 4 PTD6 VREFL CONVERTER (ADC) PTD5 VREFH D PTD4/ADP11 T R PTD3/KBIP3/ADP10 O USER Flash (IN BYTES) P PTD2/KBIP2/ACMPO ACMP– MC9S08JM60 = 60,912 PTD1/ADP9/ACMP– MC9S08JM32 = 32,768 ANALOG COMPARATOR ACMP+ PTD0/ADP8/ACMP+ (ACMP) ACMPO SS1 PTE7/SS1 USER RAM (IN BYTES) SPSCK1 8-/16-BIT SERIAL PERIPHERAL PTE6/SPSCK1 MMCC99SS0088JJMM6302 == 42009468 INTERFACE MODULE (SPI1) MOSI1 PTE5/MOSI1 MISO1 PTE4/MISO1 TPMCLK E MULTI-PURPOSE CLOCK 6-CHMAONDNUELLE T (IMTPEMR1/P)WM TTPPMM11CCHH10 PORT PTE3/TPM1CH1 GENERATOR (MCG) PTE2/TPM1CH0 TPM1CHx4 RxD1 SERIAL COMMUNICATIONS PTE1/RxD1 VSSOSC LOW-POWER OSCILLATOR TxD1 PTE0/TxD1 INTERFACE MODULE (SCI1) PTF7 VDD SYSTEM TPMCLK PTF6 VSS RVEOGLUTLAAGTEO R 2-CHMAONDNUELLE T (IMTPEMR2/P)WM TTPPMM22CCHH10 T F PPTTFF54//TTPPMM22CCHH10 OR PTF3/TPM1CH5 KBIPx P PTF2/TPM1CH4 VUSB33 USB 3.3-V VOLTAGE REGULATOR 8-BIT KEYBOARD 4 PTF1/TPM1CH3 INTERRUPT MODULE (KBI) KBIPx 4 PTF0/TPM1CH2 REAL-TIME COUNTER (RTC) EXTAL PTG5/EXTAL XTAL NOTES: G PTG4/XTAL 1. Port pins are software configurable with pullup device if input port. RT PTG3/KBIP7 O PTG2/KBIP6 2. Pin contains software configurable pullup/pull-down device if IRQ is enabled P PTG1/KBIP1 (IRQPE=1). Pull-down is enabled if rising edge detect is selected (IRQEDG=1) PTG0/KBIP0 3. IRQ does not have a clamp diode to V . IRQ must not be driven above V . DD DD 4. Pin contains integrated pullup device. 5. When pin functions as KBI (KBIPEn = 1) and associated pin is configured to enable the pullup device, KBEDGn can be used to reconfigure the pullup as a pull-down device. Figure14-1. MC9S08JM60 Series Block Diagram Highlighting the SCI Blocks and Pins MC9S08JM60 Series Data Sheet, Rev. 5 222 Freescale Semiconductor

Serial Communications Interface (S08SCIV4) 14.1.1 Features Features of SCI module include: • Full-duplex, standard non-return-to-zero (NRZ) format • Double-buffered transmitter and receiver with separate enables • Programmable baud rates (13-bit modulo divider) • Interrupt-driven or polled operation: — Transmit data register empty and transmission complete — Receive data register full — Receive overrun, parity error, framing error, and noise error — Idle receiver detect — Active edge on receive pin — Break detect supporting LIN • Hardware parity generation and checking • Programmable 8-bit or 9-bit character length • Receiver wakeup by idle-line or address-mark • Optional 13-bit break character generation / 11-bit break character detection • Selectable transmitter output polarity 14.1.2 Modes of Operation See Section14.3, “Functional Description,” For details concerning SCI operation in these modes: • 8- and 9-bit data modes • Stop mode operation • Loop mode • Single-wire mode MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 223

Serial Communications Interface (S08SCIV4) 14.1.3 Block Diagram Figure 14-2 shows the transmitter portion of the SCI. INTERNAL BUS (WRITE-ONLY) LOOPS SCID – Tx BUFFER RSRC LOOP TO RECEIVE M 11-BIT TRANSMIT SHIFT REGISTER T CONTROL DATA IN P R O A T T S S TO TxD PIN H 8 7 6 5 4 3 2 1 0 L 1 × BAUD RATE CLOCK B SHIFT DIRECTION S L TXINV D s) PE PTA8RITY D FROM SCIx SHIFT ENABLE REAMBLE (ALL 1 BREAK (ALL 0s) PT GENERATION OA P L SCI CONTROLS TxD TE SBK TO TxD TRANSMIT CONTROL TxD DIRECTION PIN LOGIC TXDIR BRK13 TDRE TIE Tx INTERRUPT TC REQUEST TCIE Figure14-2. SCI Transmitter Block Diagram MC9S08JM60 Series Data Sheet, Rev. 5 224 Freescale Semiconductor

Serial Communications Interface (S08SCIV4) Figure 14-3 shows the receiver portion of the SCI. INTERNAL BUS (READ-ONLY) 16 × BAUD DIVIDE RATE CLOCK SCID – Rx BUFFER BY 16 FROM TRANSMITTER 11-BIT RECEIVE SHIFT REGISTER T LOOPS SINGLE-WIRE M OP B AR T S T RSRC LOOP CONTROL S L S LBKDE H 8 7 6 5 4 3 2 1 0 L FROM RxD PIN s RXINV DATA RECOVERY ALL 1 MSB SHIFT DIRECTION WAKE WAKEUP RWU RWUID LOGIC ILT ACTIVE EDGE DETECT RDRF RIE IDLE ILIE Rx INTERRUPT REQUEST LBKDIF LBKDIE RXEDGIF RXEDGIE OR ORIE FE FEIE ERROR INTERRUPT REQUEST NF NEIE PE PARITY PF CHECKING PT PEIE Figure14-3. SCI Receiver Block Diagram MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 225

Serial Communications Interface (S08SCIV4) 14.2 Register Definition The SCI has eight 8-bit registers to control baud rate, select SCI options, report SCI status, and for transmit/receive data. Refer to the direct-page register summary in the Memory chapter of this data sheet for the absolute address assignments for all SCI registers. This section refers to registers and control bits only by their names. A Freescale-provided equate or header file is used to translate these names into the appropriate absolute addresses. 14.2.1 SCI Baud Rate Registers (SCIxBDH, SCIxBDL) This pair of registers controls the prescale divisor for SCI baud rate generation. To update the 13-bit baud rate setting [SBR12:SBR0], first write to SCIxBDH to buffer the high half of the new value and then write to SCIxBDL. The working value in SCIxBDH does not change until SCIxBDL is written. SCIxBDL is reset to a non-zero value, so after reset the baud rate generator remains disabled until the first time the receiver or transmitter is enabled (RE or TE bits in SCIxC2 are written to 1). 7 6 5 4 3 2 1 0 R 0 LBKDIE RXEDGIE SBR12 SBR11 SBR10 SBR9 SBR8 W Reset 0 0 0 0 0 0 0 0 = Unimplemented or Reserved Figure14-4. SCI Baud Rate Register (SCIxBDH) Table14-1. SCIxBDH Field Descriptions Field Description 7 LIN Break Detect Interrupt Enable (for LBKDIF) LBKDIE 0 Hardware interrupts from LBKDIF disabled (use polling). 1 Hardware interrupt requested when LBKDIFflag is 1. 6 RxD Input Active Edge Interrupt Enable (for RXEDGIF) RXEDGIE 0 Hardware interrupts from RXEDGIF disabled (use polling). 1 Hardware interrupt requested when RXEDGIF flag is 1. 4:0 Baud Rate Modulo Divisor — The 13 bits in SBR[12:0] are referred to collectively as BR, and they set the SBR[12:8] modulo divide rate for the SCI baud rate generator. When BR=0, the SCI baud rate generator is disabled to reduce supply current. When BR=1 to 8191, the SCI baud rate=BUSCLK/(16×BR). See also BR bits in Table14-2. MC9S08JM60 Series Data Sheet, Rev. 5 226 Freescale Semiconductor

Serial Communications Interface (S08SCIV4) 7 6 5 4 3 2 1 0 R SBR7 SBR6 SBR5 SBR4 SBR3 SBR2 SBR1 SBR0 W Reset 0 0 0 0 0 1 0 0 Figure14-5. SCI Baud Rate Register (SCIxBDL) Table14-2. SCIxBDL Field Descriptions Field Description 7:0 Baud Rate Modulo Divisor — These 13 bits in SBR[12:0] are referred to collectively as BR, and they set the SBR[7:0] modulo divide rate for the SCI baud rate generator. When BR=0, the SCI baud rate generator is disabled to reduce supply current. When BR=1 to 8191, the SCI baud rate=BUSCLK/(16×BR). See also BR bits in Table14-1. 14.2.2 SCI Control Register 1 (SCIxC1) This read/write register is used to control various optional features of the SCI system. 7 6 5 4 3 2 1 0 R LOOPS SCISWAI RSRC M WAKE ILT PE PT W Reset 0 0 0 0 0 0 0 0 Figure14-6. SCI Control Register 1 (SCIxC1) Table14-3. SCIxC1 Field Descriptions Field Description 7 Loop Mode Select — Selects between loop back modes and normal 2-pin full-duplex modes. When LOOPS=1, LOOPS the transmitter output is internally connected to the receiver input. 0 Normal operation — RxD and TxD use separate pins. 1 Loop mode or single-wire mode where transmitter outputs are internally connected to receiver input. (See RSRC bit.) RxD pin is not used by SCI. 6 SCI Stops in Wait Mode SCISWAI 0 SCI clocks continue to run in wait mode so the SCI can be the source of an interrupt that wakes up the CPU. 1 SCI clocks freeze while CPU is in wait mode. 5 Receiver Source Select — This bit has no meaning or effect unless the LOOPS bit is set to 1. When RSRC LOOPS=1, the receiver input is internally connected to the TxD pin and RSRC determines whether this connection is also connected to the transmitter output. 0 Provided LOOPS=1, RSRC=0 selects internal loop back mode and the SCI does not use the RxD pins. 1 Single-wire SCI mode where the TxD pin is connected to the transmitter output and receiver input. 4 9-Bit or 8-Bit Mode Select M 0 Normal — start + 8 data bits (LSB first) + stop. 1 Receiver and transmitter use 9-bit data characters start + 8 data bits (LSB first) + 9th data bit + stop. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 227

Serial Communications Interface (S08SCIV4) Table14-3. SCIxC1 Field Descriptions (continued) Field Description 3 Receiver Wakeup Method Select — Refer to Section14.3.3.2, “Receiver Wakeup Operation” for more WAKE information. 0 Idle-line wakeup. 1 Address-mark wakeup. 2 Idle Line Type Select — Setting this bit to 1 ensures that the stop bit and logic1 bits at the end of a character ILT do not count toward the 10 or 11 bit times of logic high level needed by the idle line detection logic. Refer to Section14.3.3.2.1, “Idle-Line Wakeup” for more information. 0 Idle character bit count starts after start bit. 1 Idle character bit count starts after stop bit. 1 Parity Enable — Enables hardware parity generation and checking. When parity is enabled, the most significant PE bit (MSB) of the data character (eighth or ninth data bit) is treated as the parity bit. 0 No hardware parity generation or checking. 1 Parity enabled. 0 Parity Type — Provided parity is enabled (PE=1), this bit selects even or odd parity. Odd parity means the total PT number of 1s in the data character, including the parity bit, is odd. Even parity means the total number of 1s in the data character, including the parity bit, is even. 0 Even parity. 1 Odd parity. 14.2.3 SCI Control Register 2 (SCIxC2) This register can be read or written at any time. 7 6 5 4 3 2 1 0 R TIE TCIE RIE ILIE TE RE RWU SBK W Reset 0 0 0 0 0 0 0 0 Figure14-7. SCI Control Register 2 (SCIxC2) Table14-4. SCIxC2 Field Descriptions Field Description 7 Transmit Interrupt Enable (for TDRE) TIE 0 Hardware interrupts from TDRE disabled (use polling). 1 Hardware interrupt requested when TDRE flag is 1. 6 Transmission Complete Interrupt Enable (for TC) TCIE 0 Hardware interrupts from TC disabled (use polling). 1 Hardware interrupt requested when TC flag is 1. 5 Receiver Interrupt Enable (for RDRF) RIE 0 Hardware interrupts from RDRF disabled (use polling). 1 Hardware interrupt requested when RDRF flag is 1. 4 Idle Line Interrupt Enable (for IDLE) ILIE 0 Hardware interrupts from IDLE disabled (use polling). 1 Hardware interrupt requested when IDLE flag is 1. MC9S08JM60 Series Data Sheet, Rev. 5 228 Freescale Semiconductor

Serial Communications Interface (S08SCIV4) Table14-4. SCIxC2 Field Descriptions (continued) Field Description 3 Transmitter Enable TE 0 Transmitter off. 1 Transmitter on. TE must be 1 in order to use the SCI transmitter. When TE=1, the SCI forces the TxD pin to act as an output for the SCI system. When the SCI is configured for single-wire operation (LOOPS=RSRC=1), TXDIR controls the direction of traffic on the single SCI communication line (TxD pin). TE also can be used to queue an idle character by writing TE=0 then TE=1 while a transmission is in progress. Refer to Section14.3.2.1, “Send Break and Queued Idle” for more details. When TE is written to 0, the transmitter keeps control of the port TxD pin until any data, queued idle, or queued break character finishes transmitting before allowing the pin to revert to a general-purpose I/O pin. 2 Receiver Enable — When the SCI receiver is off, the RxD pin reverts to being a general-purpose port I/O pin. If RE LOOPS=1 the RxD pin reverts to being a general-purpose I/O pin even if RE=1. 0 Receiver off. 1 Receiver on. 1 Receiver Wakeup Control — This bit can be written to 1 to place the SCI receiver in a standby state where it RWU waits for automatic hardware detection of a selected wakeup condition. The wakeup condition is either an idle line between messages (WAKE=0, idle-line wakeup), or a logic 1 in the most significant data bit in a character (WAKE=1, address-mark wakeup). Application software sets RWU and (normally) a selected hardware condition automatically clears RWU. Refer to Section14.3.3.2, “Receiver Wakeup Operation” for more details. 0 Normal SCI receiver operation. 1 SCI receiver in standby waiting for wakeup condition. 0 Send Break — Writing a 1 and then a 0 to SBK queues a break character in the transmit data stream. Additional SBK break characters of 10 or 11(13 or 14 if BRK13 = 1) bit times of logic 0 are queued as long as SBK=1. Depending on the timing of the set and clear of SBK relative to the information currently being transmitted, a second break character may be queued before software clears SBK. Refer to Section14.3.2.1, “Send Break and Queued Idle” for more details. 0 Normal transmitter operation. 1 Queue break character(s) to be sent. 14.2.4 SCI Status Register 1 (SCIxS1) This register has eight read-only status flags. Writes have no effect. Special software sequences (which do not involve writing to this register) are used to clear these status flags. 7 6 5 4 3 2 1 0 R TDRE TC RDRF IDLE OR NF FE PF W Reset 1 1 0 0 0 0 0 0 = Unimplemented or Reserved Figure14-8. SCI Status Register 1 (SCIxS1) MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 229

Serial Communications Interface (S08SCIV4) Table14-5. SCIxS1 Field Descriptions Field Description 7 Transmit Data Register Empty Flag — TDRE is set out of reset and when a transmit data value transfers from TDRE the transmit data buffer to the transmit shifter, leaving room for a new character in the buffer. To clear TDRE, read SCIxS1 with TDRE=1 and then write to the SCI data register (SCIxD). 0 Transmit data register (buffer) full. 1 Transmit data register (buffer) empty. 6 Transmission Complete Flag — TC is set out of reset and when TDRE=1 and no data, preamble, or break TC character is being transmitted. 0 Transmitter active (sending data, a preamble, or a break). 1 Transmitter idle (transmission activity complete). TC is cleared automatically by reading SCIxS1 with TC=1 and then doing one of the following three things: (cid:129) Write to the SCI data register (SCIxD) to transmit new data (cid:129) Queue a preamble by changing TE from 0 to 1 (cid:129) Queue a break character by writing 1 to SBK in SCIxC2 5 Receive Data Register Full Flag — RDRF becomes set when a character transfers from the receive shifter into RDRF the receive data register (SCIxD). To clear RDRF, read SCIxS1 with RDRF = 1 and then read the SCI data register (SCIxD). 0 Receive data register empty. 1 Receive data register full. 4 Idle Line Flag — IDLE is set when the SCI receive line becomes idle for a full character time after a period of IDLE activity. When ILT=0, the receiver starts counting idle bit times after the start bit. So if the receive character is all 1s, these bit times and the stop bit time count toward the full character time of logic high (10 or 11 bit times depending on the M control bit) needed for the receiver to detect an idle line. When ILT=1, the receiver doesn’t start counting idle bit times until after the stop bit. So the stop bit and any logic high bit times at the end of the previous character do not count toward the full character time of logic high needed for the receiver to detect an idle line. To clear IDLE, read SCIxS1 with IDLE=1 and then read the SCI data register (SCIxD). After IDLE has been cleared, it cannot become set again until after a new character has been received and RDRF has been set. IDLE will get set only once even if the receive line remains idle for an extended period. 0 No idle line detected. 1 Idle line was detected. 3 Receiver Overrun Flag — OR is set when a new serial character is ready to be transferred to the receive data OR register (buffer), but the previously received character has not been read from SCIxD yet. In this case, the new character (and all associated error information) is lost because there is no room to move it into SCIxD. To clear OR, read SCIxS1 with OR=1 and then read the SCI data register (SCIxD). 0 No overrun. 1 Receive overrun (new SCI data lost). 2 Noise Flag — The advanced sampling technique used in the receiver takes seven samples during the start bit NF and three samples in each data bit and the stop bit. If any of these samples disagrees with the rest of the samples within any bit time in the frame, the flag NF will be set at the same time as the flag RDRF gets set for the character. To clear NF, read SCIxS1 and then read the SCI data register (SCIxD). 0 No noise detected. 1 Noise detected in the received character in SCIxD. MC9S08JM60 Series Data Sheet, Rev. 5 230 Freescale Semiconductor

Serial Communications Interface (S08SCIV4) Table14-5. SCIxS1 Field Descriptions (continued) Field Description 1 Framing Error Flag — FE is set at the same time as RDRF when the receiver detects a logic0 where the stop FE bit was expected. This suggests the receiver was not properly aligned to a character frame. To clear FE, read SCIxS1 with FE=1 and then read the SCI data register (SCIxD). 0 No framing error detected. This does not guarantee the framing is correct. 1 Framing error. 0 Parity Error Flag — PF is set at the same time as RDRF when parity is enabled (PE=1) and the parity bit in PF the received character does not agree with the expected parity value. To clear PF, read SCIxS1 and then read the SCI data register (SCIxD). 0 No parity error. 1 Parity error. 14.2.5 SCI Status Register 2 (SCIxS2) This register has one read-only status flag. 7 6 5 4 3 2 1 0 R 0 RAF LBKDIF RXEDGIF RXINV RWUID BRK13 LBKDE W Reset 0 0 0 0 0 0 0 0 = Unimplemented or Reserved Figure14-9. SCI Status Register 2 (SCIxS2) Table14-6. SCIxS2 Field Descriptions Field Description 7 LIN Break Detect Interrupt Flag — LBKDIF is set when the LIN break detect circuitry is enabled and a LIN break LBKDIF character is detected. LBKDIF is cleared by writing a “1” to it. 0 No LIN break character has been detected. 1 LIN break character has been detected. 6 RxD Pin Active Edge Interrupt Flag — RXEDGIF is set when an active edge (falling if RXINV = 0, rising if RXEDGIF RXINV=1) on the RxD pin occurs. RXEDGIF is cleared by writing a “1” to it. 0 No active edge on the receive pin has occurred. 1 An active edge on the receive pin has occurred. 4 Receive Data Inversion — Setting this bit reverses the polarity of the received data input. RXINV1 0 Receive data not inverted 1 Receive data inverted 3 Receive Wake Up Idle Detect— RWUID controls whether the idle character that wakes up the receiver sets the RWUID IDLE bit. 0 During receive standby state (RWU = 1), the IDLE bit does not get set upon detection of an idle character. 1 During receive standby state (RWU = 1), the IDLE bit gets set upon detection of an idle character. 2 Break Character Generation Length — BRK13 is used to select a longer transmitted break character length. BRK13 Detection of a framing error is not affected by the state of this bit. 0 Break character is transmitted with length of 10 bit times (11 if M = 1) 1 Break character is transmitted with length of 13 bit times (14 if M = 1) MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 231

Serial Communications Interface (S08SCIV4) Table14-6. SCIxS2 Field Descriptions (continued) Field Description 1 LIN Break Detection Enable— LBKDE is used to select a longer break character detection length. While LBKDE LBKDE is set, framing error (FE) and receive data register full (RDRF) flags are prevented from setting. 0 Break character is detected at length of 10 bit times (11 if M = 1). 1 Break character is detected at length of 11 bit times (12 if M = 1). 0 Receiver Active Flag — RAF is set when the SCI receiver detects the beginning of a valid start bit, and RAF is RAF cleared automatically when the receiver detects an idle line. This status flag can be used to check whether an SCI character is being received before instructing the MCU to go to stop mode. 0 SCI receiver idle waiting for a start bit. 1 SCI receiver active (RxD input not idle). 1 Setting RXINV inverts the RxD input for all cases: data bits, start and stop bits, break, and idle. When using an internal oscillator in a LIN system, it is necessary to raise the break detection threshold by one bit time. Under the worst case timing conditions allowed in LIN, it is possible that a 0x00 data character can appear to be 10.26 bit times long at a slave which is running 14% faster than the master. This would trigger normal break detection circuitry which is designed to detect a 10 bit break symbol. When the LBKDE bit is set, framing errors are inhibited and the break detection threshold changes from 10 bits to 11 bits, preventing false detection of a 0x00 data character as a LIN break symbol. 14.2.6 SCI Control Register 3 (SCIxC3) 7 6 5 4 3 2 1 0 R R8 T8 TXDIR TXINV ORIE NEIE FEIE PEIE W Reset 0 0 0 0 0 0 0 0 = Unimplemented or Reserved Figure14-10. SCI Control Register 3 (SCIxC3) Table14-7. SCIxC3 Field Descriptions Field Description 7 Ninth Data Bit for Receiver — When the SCI is configured for 9-bit data (M=1), R8 can be thought of as a ninth R8 receive data bit to the left of the MSB of the buffered data in the SCIxD register. When reading 9-bit data, read R8 before reading SCIxD because reading SCIxD completes automatic flag clearing sequences which could allow R8 and SCIxD to be overwritten with new data. 6 Ninth Data Bit for Transmitter — When the SCI is configured for 9-bit data (M=1), T8 may be thought of as a T8 ninth transmit data bit to the left of the MSB of the data in the SCIxD register. When writing 9-bit data, the entire 9-bit value is transferred to the SCI shift register after SCIxD is written so T8 should be written (if it needs to change from its previous value) before SCIxD is written. If T8 does not need to change in the new value (such as when it is used to generate mark or space parity), it need not be written each time SCIxD is written. 5 TxD Pin Direction in Single-Wire Mode — When the SCI is configured for single-wire half-duplex operation TXDIR (LOOPS=RSRC=1), this bit determines the direction of data at the TxD pin. 0 TxD pin is an input in single-wire mode. 1 TxD pin is an output in single-wire mode. MC9S08JM60 Series Data Sheet, Rev. 5 232 Freescale Semiconductor

Serial Communications Interface (S08SCIV4) Table14-7. SCIxC3 Field Descriptions (continued) Field Description 4 Transmit Data Inversion — Setting this bit reverses the polarity of the transmitted data output. TXINV1 0 Transmit data not inverted 1 Transmit data inverted 3 Overrun Interrupt Enable — This bit enables the overrun flag (OR) to generate hardware interrupt requests. ORIE 0 OR interrupts disabled (use polling). 1 Hardware interrupt requested when OR=1. 2 Noise Error Interrupt Enable — This bit enables the noise flag (NF) to generate hardware interrupt requests. NEIE 0 NF interrupts disabled (use polling). 1 Hardware interrupt requested when NF=1. 1 Framing Error Interrupt Enable — This bit enables the framing error flag (FE) to generate hardware interrupt FEIE requests. 0 FE interrupts disabled (use polling). 1 Hardware interrupt requested when FE=1. 0 Parity Error Interrupt Enable — This bit enables the parity error flag (PF) to generate hardware interrupt PEIE requests. 0 PF interrupts disabled (use polling). 1 Hardware interrupt requested when PF=1. 1 Setting TXINV inverts the TxD output for all cases: data bits, start and stop bits, break, and idle. 14.2.7 SCI Data Register (SCIxD) This register is actually two separate registers. Reads return the contents of the read-only receive data buffer and writes go to the write-only transmit data buffer. Reads and writes of this register are also involved in the automatic flag clearing mechanisms for the SCI status flags. 7 6 5 4 3 2 1 0 R R7 R6 R5 R4 R3 R2 R1 R0 W T7 T6 T5 T4 T3 T2 T1 T0 Reset 0 0 0 0 0 0 0 0 Figure14-11. SCI Data Register (SCIxD) 14.3 Functional Description The SCI allows full-duplex, asynchronous, NRZ serial communication among the MCU and remote devices, including other MCUs. The SCI comprises a baud rate generator, transmitter, and receiver block. The transmitter and receiver operate independently, although they use the same baud rate generator. During normal operation, the MCU monitors the status of the SCI, writes the data to be transmitted, and processes received data. The following describes each of the blocks of the SCI. 14.3.1 Baud Rate Generation As shown in Figure 14-12, the clock source for the SCI baud rate generator is the bus-rate clock. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 233

Serial Communications Interface (S08SCIV4) MODULO DIVIDE BY (1 THROUGH 8191) DIVIDE BY BUSCLK SBR12:SBR0 16 Tx BAUD RATE Rx SAMPLING CLOCK BAUD RATE GENERATOR (16 × BAUD RATE) OFF IF [SBR12:SBR0] =0 BUSCLK BAUD RATE = [SBR12:SBR0] × 16 Figure14-12. SCI Baud Rate Generation SCI communications require the transmitter and receiver (which typically derive baud rates from independent clock sources) to use the same baud rate. Allowed tolerance on this baud frequency depends on the details of how the receiver synchronizes to the leading edge of the start bit and how bit sampling is performed. The MCU resynchronizes to bit boundaries on every high-to-low transition, but in the worst case, there are no such transitions in the full 10- or 11-bit time character frame so any mismatch in baud rate is accumulated for the whole character time. For a Freescale Semiconductor SCI system whose bus frequency is driven by a crystal, the allowed baud rate mismatch is about ±4.5 percent for 8-bit data format and about ±4 percent for 9-bit data format. Although baud rate modulo divider settings do not always produce baud rates that exactly match standard rates, it is normally possible to get within a few percent, which is acceptable for reliable communications. 14.3.2 Transmitter Functional Description This section describes the overall block diagram for the SCI transmitter, as well as specialized functions for sending break and idle characters. The transmitter block diagram is shown in Figure 14-2. The transmitter output (TxD) idle state defaults to logic high (TXINV = 0 following reset). The transmitter output is inverted by setting TXINV = 1. The transmitter is enabled by setting the TE bit in SCIxC2. This queues a preamble character that is one full character frame of the idle state. The transmitter then remains idle until data is available in the transmit data buffer. Programs store data into the transmit data buffer by writing to the SCI data register (SCIxD). The central element of the SCI transmitter is the transmit shift register that is either 10 or 11 bits long depending on the setting in the M control bit. For the remainder of this section, we will assume M =0, selecting the normal 8-bit data mode. In 8-bit data mode, the shift register holds a start bit, eight data bits, and a stop bit. When the transmit shift register is available for a new SCI character, the value waiting in the transmit data register is transferred to the shift register (synchronized with the baud rate clock) and the transmit data register empty (TDRE) status flag is set to indicate another character may be written to the transmit data buffer at SCIxD. If no new character is waiting in the transmit data buffer after a stop bit is shifted out the TxD pin, the transmitter sets the transmit complete flag and enters an idle mode, with TxD high, waiting for more characters to transmit. MC9S08JM60 Series Data Sheet, Rev. 5 234 Freescale Semiconductor

Serial Communications Interface (S08SCIV4) Writing 0 to TE does not immediately release the pin to be a general-purpose I/O pin. Any transmit activity that is in progress must first be completed. This includes data characters in progress, queued idle characters, and queued break characters. 14.3.2.1 Send Break and Queued Idle The SBK control bit in SCIxC2 is used to send break characters which were originally used to gain the attention of old teletype receivers. Break characters are a full character time of logic 0 (10 bit times including the start and stop bits). A longer break of 13 bit times can be enabled by setting BRK13 = 1. Normally, a program would wait for TDRE to become set to indicate the last character of a message has moved to the transmit shifter, then write 1 and then write 0 to the SBK bit. This action queues a break character to be sent as soon as the shifter is available. If SBK is still 1 when the queued break moves into the shifter (synchronized to the baud rate clock), an additional break character is queued. If the receiving device is another Freescale Semiconductor SCI, the break characters will be received as 0s in all eight data bits and a framing error (FE= 1) occurs. When idle-line wakeup is used, a full character time of idle (logic 1) is needed between messages to wake up any sleeping receivers. Normally, a program would wait for TDRE to become set to indicate the last character of a message has moved to the transmit shifter, then write 0 and then write 1 to the TE bit. This action queues an idle character to be sent as soon as the shifter is available. As long as the character in the shifter does not finish while TE= 0, the SCI transmitter never actually releases control of the TxD pin. If there is a possibility of the shifter finishing while TE = 0, set the general-purpose I/O controls so the pin that is shared with TxD is an output driving a logic 1. This ensures that the TxD line will look like a normal idle line even if the SCI loses control of the port pin between writing 0 and then 1 to TE. The length of the break character is affected by the BRK13 and M bits as shown below. Table14-8. Break Character Length BRK13 M Break Character Length 0 0 10 bit times 0 1 11 bit times 1 0 13 bit times 1 1 14 bit times 14.3.3 Receiver Functional Description In this section, the receiver block diagram (Figure 14-3) is used as a guide for the overall receiver functional description. Next, the data sampling technique used to reconstruct receiver data is described in more detail. Finally, two variations of the receiver wakeup function are explained. The receiver input is inverted by setting RXINV = 1. The receiver is enabled by setting the RE bit in SCIxC2. Character frames consist of a start bit of logic 0, eight (or nine) data bits (LSB first), and a stop bit of logic 1. For information about 9-bit data mode, refer to Section14.3.5.1, “8- and 9-Bit Data Modes.” For the remainder of this discussion, we assume the SCI is configured for normal 8-bit data mode. After receiving the stop bit into the receive shifter, and provided the receive data register is not already full, the data character is transferred to the receive data register and the receive data register full (RDRF) MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 235

Serial Communications Interface (S08SCIV4) status flag is set. If RDRF was already set indicating the receive data register (buffer) was already full, the overrun (OR) status flag is set and the new data is lost. Because the SCI receiver is double-buffered, the program has one full character time after RDRF is set before the data in the receive data buffer must be read to avoid a receiver overrun. When a program detects that the receive data register is full (RDRF= 1), it gets the data from the receive data register by reading SCIxD. The RDRF flag is cleared automatically by a 2-step sequence which is normally satisfied in the course of the user’s program that handles receive data. Refer to Section14.3.4, “Interrupts and Status Flags,” for more details about flag clearing. 14.3.3.1 Data Sampling Technique The SCI receiver uses a 16× baud rate clock for sampling. The receiver starts by taking logic level samples at 16 times the baud rate to search for a falling edge on the RxD serial data input pin. A falling edge is defined as a logic 0 sample after three consecutive logic 1 samples. The 16× baud rate clock is used to divide the bit time into 16segments labeled RT1 through RT16. When a falling edge is located, three more samples are taken at RT3, RT5, and RT7 to make sure this was a real start bit and not merely noise. If at least two of these three samples are 0, the receiver assumes it is synchronized to a receive character. The receiver then samples each bit time, including the start and stop bits, at RT8, RT9, and RT10 to determine the logic level for that bit. The logic level is interpreted to be that of the majority of the samples taken during the bit time. In the case of the start bit, the bit is assumed to be 0 if at least two of the samples at RT3, RT5, and RT7 are 0 even if one or all of the samples taken at RT8, RT9, and RT10 are 1s. If any sample in any bit time (including the start and stop bits) in a character frame fails to agree with the logic level for that bit, the noise flag (NF) will be set when the received character is transferred to the receive data buffer. The falling edge detection logic continuously looks for falling edges, and if an edge is detected, the sample clock is resynchronized to bit times. This improves the reliability of the receiver in the presence of noise or mismatched baud rates. It does not improve worst case analysis because some characters do not have any extra falling edges anywhere in the character frame. In the case of a framing error, provided the received character was not a break character, the sampling logic that searches for a falling edge is filled with three logic 1 samples so that a new start bit can be detected almost immediately. In the case of a framing error, the receiver is inhibited from receiving any new characters until the framing error flag is cleared. The receive shift register continues to function, but a complete character cannot transfer to the receive data buffer if FE is still set. 14.3.3.2 Receiver Wakeup Operation Receiver wakeup is a hardware mechanism that allows an SCI receiver to ignore the characters in a message that is intended for a different SCI receiver. In such a system, all receivers evaluate the first character(s) of each message, and as soon as they determine the message is intended for a different receiver, they write logic 1 to the receiver wake up (RWU) control bit in SCIxC2. When RWU bit is set, the status flags associated with the receiver (with the exception of the idle bit, IDLE, when RWUID bit is set) are inhibited from setting, thus eliminating the software overhead for handling the unimportant MC9S08JM60 Series Data Sheet, Rev. 5 236 Freescale Semiconductor

Serial Communications Interface (S08SCIV4) message characters. At the end of a message, or at the beginning of the next message, all receivers automatically force RWU to 0 so all receivers wake up in time to look at the first character(s) of the next message. 14.3.3.2.1 Idle-Line Wakeup When WAKE = 0, the receiver is configured for idle-line wakeup. In this mode, RWU is cleared automatically when the receiver detects a full character time of the idle-line level. The M control bit selects 8-bit or 9-bit data mode that determines how many bit times of idle are needed to constitute a full character time (10 or 11 bit times because of the start and stop bits). When RWU is one and RWUID is zero, the idle condition that wakes up the receiver does not set the IDLE flag. The receiver wakes up and waits for the first data character of the next message which will set the RDRF flag and generate an interrupt if enabled. When RWUID is one, any idle condition sets the IDLE flag and generates an interrupt if enabled, regardless of whether RWU is zero or one. The idle-line type (ILT) control bit selects one of two ways to detect an idle line. When ILT = 0, the idle bit counter starts after the start bit so the stop bit and any logic 1s at the end of a character count toward the full character time of idle. When ILT = 1, the idle bit counter does not start until after a stop bit time, so the idle detection is not affected by the data in the last character of the previous message. 14.3.3.2.2 Address-Mark Wakeup When WAKE = 1, the receiver is configured for address-mark wakeup. In this mode, RWU is cleared automatically when the receiver detects a logic 1 in the most significant bit of a received character (eighth bit in M = 0 mode and ninth bit in M = 1 mode). Address-mark wakeup allows messages to contain idle characters but requires that the MSB be reserved for use in address frames. The logic 1 MSB of an address frame clears the RWU bit before the stop bit is received and sets the RDRF flag. In this case the character with the MSB set is received even though the receiver was sleeping during most of this character time. 14.3.4 Interrupts and Status Flags The SCI system has three separate interrupt vectors to reduce the amount of software needed to isolate the cause of the interrupt. One interrupt vector is associated with the transmitter for TDRE and TC events. Another interrupt vector is associated with the receiver for RDRF, IDLE, RXEDGIF and LBKDIF events, and a third vector is used for OR, NF, FE, and PF error conditions. Each of these ten interrupt sources can be separately masked by local interrupt enable masks. The flags can still be polled by software when the local masks are cleared to disable generation of hardware interrupt requests. The SCI transmitter has two status flags that optionally can generate hardware interrupt requests. Transmit data register empty (TDRE) indicates when there is room in the transmit data buffer to write another transmit character to SCIxD. If the transmit interrupt enable (TIE) bit is set, a hardware interrupt will be requested whenever TDRE=1. Transmit complete (TC) indicates that the transmitter is finished transmitting all data, preamble, and break characters and is idle with TxD at the inactive level. This flag is often used in systems with modems to determine when it is safe to turn off the modem. If the transmit complete interrupt enable (TCIE) bit is set, a hardware interrupt will be requested whenever TC= 1. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 237

Serial Communications Interface (S08SCIV4) Instead of hardware interrupts, software polling may be used to monitor the TDRE and TC status flags if the corresponding TIE or TCIE local interrupt masks are 0s. When a program detects that the receive data register is full (RDRF= 1), it gets the data from the receive data register by reading SCIxD. The RDRF flag is cleared by reading SCIxS1 while RDRF=1 and then reading SCIxD. When polling is used, this sequence is naturally satisfied in the normal course of the user program. If hardware interrupts are used, SCIxS1 must be read in the interrupt service routine (ISR). Normally, this is done in the ISR anyway to check for receive errors, so the sequence is automatically satisfied. The IDLE status flag includes logic that prevents it from getting set repeatedly when the RxD line remains idle for an extended period of time. IDLE is cleared by reading SCIxS1 while IDLE=1 and then reading SCIxD. After IDLE has been cleared, it cannot become set again until the receiver has received at least one new character and has set RDRF. If the associated error was detected in the received character that caused RDRF to be set, the error flags — noise flag (NF), framing error (FE), and parity error flag (PF) — get set at the same time as RDRF. These flags are not set in overrun cases. If RDRF was already set when a new character is ready to be transferred from the receive shifter to the receive data buffer, the overrun (OR) flag gets set instead the data along with any associated NF, FE, or PF condition is lost. At any time, an active edge on the RxD serial data input pin causes the RXEDGIF flag to set. The RXEDGIF flag is cleared by writing a “1” to it. This function does depend on the receiver being enabled (RE = 1). 14.3.5 Additional SCI Functions The following sections describe additional SCI functions. 14.3.5.1 8- and 9-Bit Data Modes The SCI system (transmitter and receiver) can be configured to operate in 9-bit data mode by setting the M control bit in SCIxC1. In 9-bit mode, there is a ninth data bit to the left of the MSB of the SCI data register. For the transmit data buffer, this bit is stored in T8 in SCIxC3. For the receiver, the ninth bit is held in R8 in SCIxC3. For coherent writes to the transmit data buffer, write to the T8 bit before writing to SCIxD. If the bit value to be transmitted as the ninth bit of a new character is the same as for the previous character, it is not necessary to write to T8 again. When data is transferred from the transmit data buffer to the transmit shifter, the value in T8 is copied at the same time data is transferred from SCIxD to the shifter. 9-bit data mode typically is used in conjunction with parity to allow eight bits of data plus the parity in the ninth bit. Or it is used with address-mark wakeup so the ninth data bit can serve as the wakeup bit. In custom protocols, the ninth bit can also serve as a software-controlled marker. MC9S08JM60 Series Data Sheet, Rev. 5 238 Freescale Semiconductor

Serial Communications Interface (S08SCIV4) 14.3.5.2 Stop Mode Operation During all stop modes, clocks to the SCI module are halted. In stop1 and stop2 modes, all SCI register data is lost and must be re-initialized upon recovery from these two stop modes. No SCI module registers are affected in stop3 mode. The receive input active edge detect circuit is still active in stop3 mode, but not in stop2.. An active edge on the receive input brings the CPU out of stop3 mode if the interrupt is not masked (RXEDGIE = 1). Note, because the clocks are halted, the SCI module will resume operation upon exit from stop (only in stop3 mode). Software should ensure stop mode is not entered while there is a character being transmitted out of or received into the SCI module. 14.3.5.3 Loop Mode When LOOPS= 1, the RSRC bit in the same register chooses between loop mode (RSRC= 0) or single-wire mode (RSRC= 1). Loop mode is sometimes used to check software, independent of connections in the external system, to help isolate system problems. In this mode, the transmitter output is internally connected to the receiver input and the RxD pin is not used by the SCI, so it reverts to a general-purpose port I/O pin. 14.3.5.4 Single-Wire Operation When LOOPS= 1, the RSRC bit in the same register chooses between loop mode (RSRC= 0) or single-wire mode (RSRC= 1). Single-wire mode is used to implement a half-duplex serial connection. The receiver is internally connected to the transmitter output and to the TxD pin. The RxD pin is not used and reverts to a general-purpose port I/O pin. In single-wire mode, the TXDIR bit in SCIxC3 controls the direction of serial data on the TxD pin. When TXDIR= 0, the TxD pin is an input to the SCI receiver and the transmitter is temporarily disconnected from the TxD pin so an external device can send serial data to the receiver. When TXDIR= 1, the TxD pin is an output driven by the transmitter. In single-wire mode, the internal loop back connection from the transmitter to the receiver causes the receiver to receive characters that are sent out by the transmitter. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 239

Serial Communications Interface (S08SCIV4) MC9S08JM60 Series Data Sheet, Rev. 5 240 Freescale Semiconductor

Chapter 15 16-Bit Serial Peripheral Interface (S08SPI16V1) 15.1 Introduction The 8- or 16-bit selectable serial peripheral interface (SPI) module provides for full-duplex, synchronous, serial communication between the MCU and peripheral devices. These peripheral devices can include other microcontrollers, analog-to-digital converters, shift registers, sensors, memories, etc. The SPI runs at a baud rate up to the bus clock divided by two in master mode and up to the bus clock divided by four in slave mode. Software can poll the status flags, or SPI operation can be interrupt driven. The SPI also supports a data length of 8 or 16 bits and includes a hardware match feature for the receive data buffer. The MC9S08JM60 series have two serial peripheral interface modules (SPI1 and SPI2). The four pins associated with SPI functionality are shared with PTB[3:0] and PTE[7:4]. See AppendixA, “Electrical Characteristics,” for SPI electrical parametric information. 15.1.1 SPI Port Configuration Information By default, the input filters on the SPI port pins will be enabled (SPIxFE=1), which restricts the SPI data rate to 6 MHz, but protects the SPI from noise during data transfers.To configure the SPI at a baud rate of 6MHz or greater, the input filters on the SPI port pins must be disabled by clearing the SPIxFE in SOPT2. and also enable the high output drive strength selection on the affected SPI port pins. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 241

Chapter15 16-Bit Serial Peripheral Interface (S08SPI16V1) USBDP ON-CHIP ICE AND USBDN HCS08 CORE DEBUG MODULE (DBG) A T 6 R PTA5– PTA0 O USB SIE P BKGD/MS FULL SPEED PTB7/ADP7 BDC CPU USB PTB6/ADP6 USB ERNADMPOINT TRANSCEIVER B PTB5/KBIP5/ADP5 T PTB4/KBIP4/ADP4 SSPSS2CK2 POR PTB3/SS2/ADP3 RESET HCS08 SYSTEM CONTROL 8-/16-BIT SERIAL PERIPHERAL MOSI2 PTB2/SPSCK2/ADP2 INTERFACE MODULE (SPI2) PTB1/MOSI2/ADP1 MISO2 PTB0/MISO2/ADP0 RESETS AND INTERRUPTS MODES OF OPERATION PTC6 IRQ/TPMCLK POWER MANAGEMENT SERIAL COMMUNICATIONS RxD2 PTC5/RxD2 COP IRQ LVD INTERFACE MODULE (SCI2) TxD2 ORT C PPTTCC34/TxD2 P PTC2 SDA PTC1/SDA IIC MODULE (IIC) SCL PTC0/SCL VDDAD 12-CHANNEL, 12-BIT 8 PTD7 VSSAD ANALOG-TO-DIGITAL 4 PTD6 VREFL CONVERTER (ADC) PTD5 VREFH D PTD4/ADP11 T R PTD3/KBIP3/ADP10 O USER Flash (IN BYTES) P PTD2/KBIP2/ACMPO ACMP– MC9S08JM60 = 60,912 PTD1/ADP9/ACMP– MC9S08JM32 = 32,768 ANALOG COMPARATOR ACMP+ PTD0/ADP8/ACMP+ (ACMP) ACMPO SS1 PTE7/SS1 USER RAM (IN BYTES) SPSCK1 8-/16-BIT SERIAL PERIPHERAL PTE6/SPSCK1 MMCC99SS0088JJMM6302 == 42009468 INTERFACE MODULE (SPI1) MOSI1 PTE5/MOSI1 MISO1 PTE4/MISO1 TPMCLK E MULTI-PURPOSE CLOCK 6-CHMAONDNUELLE T (IMTPEMR1/P)WM TTPPMM11CCHH10 PORT PTE3/TPM1CH1 GENERATOR (MCG) PTE2/TPM1CH0 TPM1CHx4 RxD1 SERIAL COMMUNICATIONS PTE1/RxD1 VSSOSC LOW-POWER OSCILLATOR TxD1 PTE0/TxD1 INTERFACE MODULE (SCI1) PTF7 VDD SYSTEM TPMCLK PTF6 VSS RVEOGLUTLAAGTEO R 2-CHMAONDNUELLE T (IMTPEMR2/P)WM TTPPMM22CCHH10 T F PPTTFF54//TTPPMM22CCHH10 OR PTF3/TPM1CH5 KBIPx P PTF2/TPM1CH4 VUSB33 USB 3.3-V VOLTAGE REGULATOR 8-BIT KEYBOARD 4 PTF1/TPM1CH3 INTERRUPT MODULE (KBI) KBIPx 4 PTF0/TPM1CH2 REAL-TIME COUNTER (RTC) EXTAL PTG5/EXTAL XTAL NOTES: G PTG4/XTAL 1. Port pins are software configurable with pullup device if input port. RT PTG3/KBIP7 O PTG2/KBIP6 2. Pin contains software configurable pullup/pull-down device if IRQ is enabled P PTG1/KBIP1 (IRQPE=1). Pull-down is enabled if rising edge detect is selected (IRQEDG=1) PTG0/KBIP0 3. IRQ does not have a clamp diode to V . IRQ must not be driven above V . DD DD 4. Pin contains integrated pullup device. 5. When pin functions as KBI (KBIPEn = 1) and associated pin is configured to enable the pullup device, KBEDGn can be used to reconfigure the pullup as a pull-down device. Figure15-1. MC9S08JM60 Series Block Diagram Highlighting the SPI Blocks and Pins MC9S08JM60 Series Data Sheet, Rev. 5 242 Freescale Semiconductor

Serial Peripheral Interface (S08SPI16V1) Module Initialization (Slave): Write: SPIxC1 to configure interrupts, set primary SPI options, slave mode select, and system enable. Write: SPIxC2 to configure optional SPI features, hardware match interrupt enable, and 8- or 16-bit data transmission length Write: SPIxMH:SPIxML to set hardware compare value that triggers SPMF (optional) when value in receive data buffer equals this value. Module Initialization (Master): Write: SPIxC1 to configure interrupts, set primary SPI options, master mode select, and system enable. Write: SPIxC2 to configure optional SPI features, hardware match interrupt enable, and 8- or 16-bit data transmission length Write: SPIxBR to set baud rate Write: SPIxMH:SPIxML to set hardware compare value that triggers SPMF (optional) when value in receive data buffer equals this value. Module Use: After SPI master initiates transfer by checking that SPTEF = 1 and then writing data to SPIDH/L: Wait for SPRF, then read from SPIDH/L Wait for SPTEF, then write to SPIDH/L Data transmissions can be 8- or 16-bits long, and mode fault detection can be enabled for master mode in cases where more than one SPI device might become a master at the same time. Also, some applications may utilize the receive data buffer hardware match feature to trigger specific actions, such as when command data can be sent through the SPI or to indicate the end of an SPI transmission. SPIxC1 SPIE SPE SPTIE MSTR CPOL CPHA SSOE LSBFE Module/interrupt enables and configuration SPIxC2 SPMIE SPIMODE MODFEN BIDIROE SPISWAI SPC0 Additional configuration options. SPIxBR SPPR2 SPPR1 SPPR0 SPR2 SPR1 SPR0 Baud rate = (BUSCLK/SPPR[2:0])/SPR2[2:0] SPIxDH Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 SPIxDL Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 SPIxMH Bit 15 Bit 14 Bit 13 Bit 12 Bit 11 Bit 10 Bit 9 Bit 8 SPIxML Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Hardware Match Value SPIxS SPRF SPMF SPTEF MODF Figure15-2. SPI Module Quick Start MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 243

Serial Peripheral Interface (S08SPI16V1) 15.1.2 Features The SPI includes these distinctive features: • Master mode or slave mode operation • Full-duplex or single-wire bidirectional mode • Programmable transmit bit rate • Double-buffered transmit and receive data register • Serial clock phase and polarity options • Slave select output • Mode fault error flag with CPU interrupt capability • Control of SPI operation during wait mode • Selectable MSB-first or LSB-first shifting • Programmable 8- or 16-bit data transmission length • Receive data buffer hardware match feature 15.1.3 Modes of Operation The SPI functions in three modes, run, wait, and stop. • Run Mode This is the basic mode of operation. • Wait Mode SPI operation in wait mode is a configurable low power mode, controlled by the SPISWAI bit located in the SPIxC2 register. In wait mode, if the SPISWAI bit is clear, the SPI operates like in Run Mode. If the SPISWAI bit is set, the SPI goes into a power conservative state, with the SPI clock generation turned off. If the SPI is configured as a master, any transmission in progress stops, but is resumed after CPU goes into Run Mode. If the SPI is configured as a slave, reception and transmission of a byte continues, so that the slave stays synchronized to the master. • Stop Mode The SPI is inactive in stop3 mode for reduced power consumption. If the SPI is configured as a master, any transmission in progress stops, but is resumed after the CPU goes into Run Mode. If the SPI is configured as a slave, reception and transmission of a data continues, so that the slave stays synchronized to the master. The SPI is completely disabled in all other stop modes. When the CPU wakes from these stop modes, all SPI register content will be reset. This is a high level description only, detailed descriptions of operating modes are contained in section Section15.4.9, “Low Power Mode Options.” 15.1.4 Block Diagrams This section includes block diagrams showing SPI system connections, the internal organization of the SPI module, and the SPI clock dividers that control the master mode bit rate. MC9S08JM60 Series Data Sheet, Rev. 5 244 Freescale Semiconductor

Serial Peripheral Interface (S08SPI16V1) 15.1.4.1 SPI System Block Diagram Figure 15-3 shows the SPI modules of two MCUs connected in a master-slave arrangement. The master device initiates all SPI data transfers. During a transfer, the master shifts data out (on the MOSI pin) to the slave while simultaneously shifting data in (on the MISO pin) from the slave. The transfer effectively exchanges the data that was in the SPI shift registers of the two SPI systems. The SPSCK signal is a clock output from the master and an input to the slave. The slave device must be selected by a low level on the slave select input (SS pin). In this system, the master device has configured its SS pin as an optional slave select output. MASTER SLAVE MOSI MOSI SPI SHIFTER SPI SHIFTER MISO MISO 8 OR 16 BITS 8 OR 16 BITS SPSCK SPSCK CLOCK GENERATOR SS SS Figure15-3. SPI System Connections 15.1.4.2 SPI Module Block Diagram Figure 15-4 is a block diagram of the SPI module. The central element of the SPI is the SPI shift register. Data is written to the double-buffered transmitter (write to SPIxDH:SPIxDL) and gets transferred to the SPI shift register at the start of a data transfer. After shifting in 8 or 16 bits (as determined by SPIMODE bit) of data, the data is transferred into the double-buffered receiver where it can be read (read from SPIxDH:SPIxDL). Pin multiplexing logic controls connections between MCU pins and the SPI module. When the SPI is configured as a master, the clock output is routed to the SPSCK pin, the shifter output is routed to MOSI, and the shifter input is routed from the MISO pin. When the SPI is configured as a slave, the SPSCK pin is routed to the clock input of the SPI, the shifter output is routed to MISO, and the shifter input is routed from the MOSI pin. In the external SPI system, simply connect all SPSCK pins to each other, all MISO pins together, and all MOSI pins together. Peripheral devices often use slightly different names for these pins. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 245

Serial Peripheral Interface (S08SPI16V1) PIN CONTROL M MOSI SPE S (MOMI) Tx BUFFER (WRITE SPIxDH:SPIxDL) ENABLE SPI SYSTEM M MISO SHIFT SPI SHIFT REGISTER SHIFT S (SISO) OUT IN 8 OR 16 SPIMODE BIT MODE SPC0 Rx BUFFER (READ SPIxDH:SPIxDL) BIDIROE SHIFT SHIFT Rx BUFFER Tx BUFFER LSBFE DIRECTION CLOCK FULL EMPTY MASTER CLOCK M BUS RATE SPIBR CLOCK SPSCK CLOCK CLOCK GENERATOR LOGIC SLAVE CLOCK S MASTER/SLAVE MASTER/ MSTR MODE SELECT SLAVE MODFEN SSOE MODE FAULT SS DETECTION 16-BIT COMPARATOR SPMF SPIxMH:SPIxML SPMIE 16-BIT LATCH SPRF SPTEF SPTIE SPI INTERRUPT MODF REQUEST SPIE Figure15-4. SPI Module Block Diagram 15.2 External Signal Description The SPI optionally shares four port pins. The function of these pins depends on the settings of SPI control bits. When the SPI is disabled (SPE = 0), these four pins revert to being general-purpose port I/O pins that are not controlled by the SPI. 15.2.1 SPSCK — SPI Serial Clock When the SPI is enabled as a slave, this pin is the serial clock input. When the SPI is enabled as a master, this pin is the serial clock output. MC9S08JM60 Series Data Sheet, Rev. 5 246 Freescale Semiconductor

Serial Peripheral Interface (S08SPI16V1) 15.2.2 MOSI — Master Data Out, Slave Data In When the SPI is enabled as a master and SPI pin control zero (SPC0) is 0 (not bidirectional mode), this pin is the serial data output. When the SPI is enabled as a slave and SPC0= 0, this pin is the serial data input. If SPC0= 1 to select single-wire bidirectional mode, and master mode is selected, this pin becomes the bidirectional data I/O pin (MOMI). Also, the bidirectional mode output enable bit determines whether the pin acts as an input (BIDIROE =0) or an output (BIDIROE= 1). If SPC0= 1 and slave mode is selected, this pin is not used by the SPI and reverts to being a general-purpose port I/O pin. 15.2.3 MISO — Master Data In, Slave Data Out When the SPI is enabled as a master and SPI pin control zero (SPC0) is 0 (not bidirectional mode), this pin is the serial data input. When the SPI is enabled as a slave and SPC0= 0, this pin is the serial data output. If SPC0= 1 to select single-wire bidirectional mode, and slave mode is selected, this pin becomes the bidirectional data I/O pin (SISO) and the bidirectional mode output enable bit determines whether the pin acts as an input (BIDIROE= 0) or an output (BIDIROE= 1). If SPC0= 1 and master mode is selected, this pin is not used by the SPI and reverts to being a general-purpose port I/O pin. 15.2.4 SS — Slave Select When the SPI is enabled as a slave, this pin is the low-true slave select input. When the SPI is enabled as a master and mode fault enable is off (MODFEN= 0), this pin is not used by the SPI and reverts to being a general-purpose port I/O pin. When the SPI is enabled as a master and MODFEN= 1, the slave select output enable bit determines whether this pin acts as the mode fault input (SSOE= 0) or as the slave select output (SSOE= 1). 15.3 Register Definition The SPI has eight 8-bit registers to select SPI options, control baud rate, report SPI status, hold an SPI data match value, and for transmit/receive data. Refer to the direct-page register summary in the Memory chapter of this data sheet for the absolute address assignments for all SPI registers. This section refers to registers and control bits only by their names, and a Freescale-provided equate or header file is used to translate these names into the appropriate absolute addresses. 15.3.1 SPI Control Register 1 (SPIxC1) This read/write register includes the SPI enable control, interrupt enables, and configuration options. 7 6 5 4 3 2 1 0 R SPIE SPE SPTIE MSTR CPOL CPHA SSOE LSBFE W Reset 0 0 0 0 0 1 0 0 Figure15-5. SPI Control Register 1 (SPIxC1) MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 247

Serial Peripheral Interface (S08SPI16V1) Table15-1. SPIxC1 Field Descriptions Field Description 7 SPI Interrupt Enable (for SPRF and MODF) — This is the interrupt enable for SPI receive buffer full (SPRF) SPIE and mode fault (MODF) events. 0 Interrupts from SPRF and MODF inhibited (use polling) 1 When SPRF or MODF is 1, request a hardware interrupt 6 SPI System Enable — This bit enables the SPI system and dedicates the SPI port pins to SPI system functions. SPE If SPE is cleared, SPI is disabled and forced into idle state, and all status bits in the SPIxS register are reset. 0 SPI system inactive 1 SPI system enabled 5 SPI Transmit Interrupt Enable — This is the interrupt enable bit for SPI transmit buffer empty (SPTEF). SPTIE 0 Interrupts from SPTEF inhibited (use polling) 1 When SPTEF is 1, hardware interrupt requested 4 Master/Slave Mode Select — This bit selects master or slave mode operation. MSTR 0 SPI module configured as a slave SPI device 1 SPI module configured as a master SPI device 3 Clock Polarity — This bit selects an inverted or non-inverted SPI clock. To transmit data between SPI modules, CPOL the SPI modules must have identical CPOL values. This bit effectively places an inverter in series with the clock signal from a master SPI or to a slave SPI device. Refer to Section15.4.5, “SPI Clock Formats” for more details. 0 Active-high SPI clock (idles low) 1 Active-low SPI clock (idles high) 2 Clock Phase — This bit selects one of two clock formats for different kinds of synchronous serial peripheral CPHA devices. Refer to Section15.4.5, “SPI Clock Formats” for more details. 0 First edge on SPSCK occurs at the middle of the first cycle of a data transfer 1 First edge on SPSCK occurs at the start of the first cycle of a data transfer 1 Slave Select Output Enable — This bit is used in combination with the mode fault enable (MODFEN) bit in SSOE SPIxC2 and the master/slave (MSTR) control bit to determine the function of the SS pin as shown in Table15-2. 0 LSB First (Shifter Direction) — This bit does not affect the position of the MSB and LSB in the data register. LSBFE Reads and writes of the data register always have the MSB in bit 7 (or bit 15 in 16-bit mode). 0 SPI serial data transfers start with most significant bit 1 SPI serial data transfers start with least significant bit Table15-2. SS Pin Function MODFEN SSOE Master Mode Slave Mode 0 0 General-purpose I/O (not SPI) Slave select input 0 1 General-purpose I/O (not SPI) Slave select input 1 0 SS input for mode fault Slave select input 1 1 Automatic SS output Slave select input 15.3.2 SPI Control Register 2 (SPIxC2) This read/write register is used to control optional features of the SPI system. Bits 6 and 5 are not implemented and always read 0. MC9S08JM60 Series Data Sheet, Rev. 5 248 Freescale Semiconductor

Serial Peripheral Interface (S08SPI16V1) 7 6 5 4 3 2 1 0 R 0 0 SPMIE SPIMODE MODFEN BIDIROE SPISWAI SPC0 W Reset 0 0 0 0 0 0 0 0 = Unimplemented or Reserved Figure15-6. SPI Control Register 2 (SPIxC2) Table15-3. SPIxC2 Register Field Descriptions Field Description 7 SPI Match Interrupt Enable — This is the interrupt enable for the SPI receive data buffer hardware match SPMIE (SPMF) function. 0 Interrupts from SPMF inhibited (use polling). 1 When SPMF = 1, requests a hardware interrupt. 6 SPI 8- or 16-bit Mode — This bit allows the user to select either an 8-bit or 16-bit SPI data transmission length. SPIMODE In master mode, a change of this bit will abort a transmission in progress, force the SPI system into idle state, and reset all status bits in the SPIxS register. Refer to section Section15.4.4, “Data Transmission Length,” for details. 0 8-bit SPI shift register, match register, and buffers. 1 16-bit SPI shift register, match register, and buffers. 4 Master Mode-Fault Function Enable — When the SPI is configured for slave mode, this bit has no meaning or MODFEN effect. (The SS pin is the slave select input.) In master mode, this bit determines how the SS pin is used (refer to Table15-2 for details) 0 Mode fault function disabled, master SS pin reverts to general-purpose I/O not controlled by SPI 1 Mode fault function enabled, master SS pin acts as the mode fault input or the slave select output 3 Bidirectional Mode Output Enable — When bidirectional mode is enabled by SPI pin control 0 (SPC0)=1, BIDIROE BIDIROE determines whether the SPI data output driver is enabled to the single bidirectional SPI I/O pin. Depending on whether the SPI is configured as a master or a slave, it uses either the MOSI (MOMI) or MISO (SISO) pin, respectively, as the single SPI data I/O pin. When SPC0=0, BIDIROE has no meaning or effect. 0 Output driver disabled so SPI data I/O pin acts as an input 1 SPI I/O pin enabled as an output 1 SPI Stop in Wait Mode — This bit is used for power conservation while in wait. SPISWAI 0 SPI clocks continue to operate in wait mode 1 SPI clocks stop when the MCU enters wait mode 0 SPI Pin Control 0 — This bit enables bidirectional pin configurations as shown in Table15-4. SPC0 0 SPI uses separate pins for data input and data output. 1 SPI configured for single-wire bidirectional operation. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 249

Serial Peripheral Interface (S08SPI16V1) Table15-4. Bidirectional Pin Configurations Pin Mode SPC0 BIDIROE MISO MOSI Master Mode of Operation Normal 0 X Master In Master Out Bidirectional 1 0 MISO not used by SPI Master In 1 Master I/O Slave Mode of Operation Normal 0 X Slave Out Slave In Bidirectional 1 0 Slave In MOSI not used by SPI 1 Slave I/O 15.3.3 SPI Baud Rate Register (SPIxBR) This register is used to set the prescaler and bit rate divisor for an SPI master. This register may be read or written at any time. 7 6 5 4 3 2 1 0 R 0 0 SPPR2 SPPR1 SPPR0 SPR2 SPR1 SPR0 W Reset 0 0 0 0 0 0 0 0 = Unimplemented or Reserved Figure15-7. SPI Baud Rate Register (SPIxBR) Table15-5. SPIxBR Register Field Descriptions Field Description 6:4 SPI Baud Rate Prescale Divisor — This 3-bit field selects one of eight divisors for the SPI baud rate prescaler SPPR[2:0] as shown in Table15-6. The input to this prescaler is the bus rate clock (BUSCLK). The output of this prescaler drives the input of the SPI baud rate divider (see Figure15-15). See Section15.4.6, “SPI Baud Rate Generation,” for details. 2:0 SPI Baud Rate Divisor — This 3-bit field selects one of eight divisors for the SPI baud rate divider as shown in SPR[2:0] Table15-7. The input to this divider comes from the SPI baud rate prescaler (see Figure15-15). See Section15.4.6, “SPI Baud Rate Generation,” for details. MC9S08JM60 Series Data Sheet, Rev. 5 250 Freescale Semiconductor

Serial Peripheral Interface (S08SPI16V1) Table15-6. SPI Baud Rate Prescaler Divisor SPPR2:SPPR1:SPPR0 Prescaler Divisor 0:0:0 1 0:0:1 2 0:1:0 3 0:1:1 4 1:0:0 5 1:0:1 6 1:1:0 7 1:1:1 8 Table15-7. SPI Baud Rate Divisor SPR2:SPR1:SPR0 Rate Divisor 0:0:0 2 0:0:1 4 0:1:0 8 0:1:1 16 1:0:0 32 1:0:1 64 1:1:0 128 1:1:1 256 15.3.4 SPI Status Register (SPIxS) This register has four read-only status bits. Bits 3 through 0 are not implemented and always read 0. Writes have no meaning or effect. 7 6 5 4 3 2 1 0 R SPRF SPMF SPTEF MODF 0 0 0 0 W Reset 0 0 1 0 0 0 0 0 = Unimplemented or Reserved Figure15-8. SPI Status Register (SPIxS) MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 251

Serial Peripheral Interface (S08SPI16V1) Table15-8. SPIxS Register Field Descriptions Field Description 7 SPI Read Buffer Full Flag — SPRF is set at the completion of an SPI transfer to indicate that received data may SPRF be read from the SPI data register (SPIxDH:SPIxDL). SPRF is cleared by reading SPRF while it is set, then reading the SPI data register. 0 No data available in the receive data buffer. 1 Data available in the receive data buffer. 6 SPI Match Flag — SPMF is set after SPRF = 1 when the value in the receive data buffer matches the value in SPMF SPIMH:SPIML. To clear the flag, read SPMF when it is set, then write a 1 to it. 0 Value in the receive data buffer does not match the value in SPIxMH:SPIxML registers. 1 Value in the receive data buffer matches the value in SPIxMH:SPIxML registers. 5 SPI Transmit Buffer Empty Flag — This bit is set when the transmit data buffer is empty. It is cleared by reading SPTEF SPIxS with SPTEF set, followed by writing a data value to the transmit buffer at SPIxDH:SPIxDL. SPIxS must be read with SPTEF=1 before writing data to SPIxDH:SPIxDL or the SPIxDH:SPIxDL write will be ignored. SPTEF is automatically set when all data from the transmit buffer transfers into the transmit shift register. For an idle SPI, data written to SPIxDH:SPIxDL is transferred to the shifter almost immediately so SPTEF is set within two bus cycles allowing a second data to be queued into the transmit buffer. After completion of the transfer of the data in the shift register, the queued data from the transmit buffer will automatically move to the shifter and SPTEF will be set to indicate there is room for new data in the transmit buffer. If no new data is waiting in the transmit buffer, SPTEF simply remains set and no data moves from the buffer to the shifter. 0 SPI transmit buffer not empty 1 SPI transmit buffer empty 4 Master Mode Fault Flag — MODF is set if the SPI is configured as a master and the slave select input goes low, MODF indicating some other SPI device is also configured as a master. The SS pin acts as a mode fault error input only when MSTR=1, MODFEN=1, and SSOE=0; otherwise, MODF will never be set. MODF is cleared by reading MODF while it is 1, then writing to SPI control register 1 (SPIxC1). 0 No mode fault error 1 Mode fault error detected 15.3.5 SPI Data Registers (SPIxDH:SPIxDL) 7 6 5 4 3 2 1 0 R Bit 15 14 13 12 11 10 9 Bit 8 W Reset 0 0 0 0 0 0 0 0 Figure15-9. SPI Data Register High (SPIxDH) 7 6 5 4 3 2 1 0 R Bit 7 6 5 4 3 2 1 Bit 0 W Reset 0 0 0 0 0 0 0 0 Figure15-10. SPI Data Register Low (SPIxDL) The SPI data registers (SPIxDH:SPIxDL) are both the input and output register for SPI data. A write to these registers writes to the transmit data buffer, allowing data to be queued and transmitted. MC9S08JM60 Series Data Sheet, Rev. 5 252 Freescale Semiconductor

Serial Peripheral Interface (S08SPI16V1) When the SPI is configured as a master, data queued in the transmit data buffer is transmitted immediately after the previous transmission has completed. The SPI transmit buffer empty flag (SPTEF) in the SPIxS register indicates when the transmit data buffer is ready to accept new data. SPIxS must be read when SPTEF is set before writing to the SPI data registers, or the write will be ignored. Data may be read from SPIxDH:SPIxDL any time after SPRF is set and before another transfer is finished. Failure to read the data out of the receive data buffer before a new transfer ends causes a receive overrun condition and the data from the new transfer is lost. In 8-bit mode, only SPIxDL is available. Reads of SPIxDH will return all 0s. Writes to SPIxDH will be ignored. In 16-bit mode, reading either byte (SPIxDH or SPIxDL) latches the contents of both bytes into a buffer where they remain latched until the other byte is read. Writing to either byte (SPIxDH or SPIxDL) latches the value into a buffer. When both bytes have been written, they are transferred as a coherent 16-bit value into the transmit data buffer. 15.3.6 SPI Match Registers (SPIxMH:SPIxML) These read/write registers contain the hardware compare value, which sets the SPI match flag (SPMF) when the value received in the SPI receive data buffer equals the value in the SPIxMH:SPIxML registers. In 8-bit mode, only SPIxML is available. Reads of SPIxMH will return all 0s. Writes to SPIxMH will be ignored. In 16-bit mode, reading either byte (SPIxMH or SPIxML) latches the contents of both bytes into a buffer where they remain latched until the other byte is read. Writing to either byte (SPIxMH or SPIxML) latches the value into a buffer. When both bytes have been written, they are transferred as a coherent value into the SPI match registers. 7 6 5 4 3 2 1 0 R Bit 15 14 13 12 11 10 9 Bit 8 W Reset 0 0 0 0 0 0 0 0 Figure15-11. SPI Match Register High (SPIxMH) 7 6 5 4 3 2 1 0 R Bit 7 6 5 4 3 2 1 Bit 0 W Reset 0 0 0 0 0 0 0 0 Figure15-12. SPI Match Register Low (SPIxML) MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 253

Serial Peripheral Interface (S08SPI16V1) 15.4 Functional Description 15.4.1 General The SPI system is enabled by setting the SPI enable (SPE) bit in SPI Control Register 1. While the SPE bit is set, the four associated SPI port pins are dedicated to the SPI function as: • Slave select (SS) • Serial clock (SPSCK) • Master out/slave in (MOSI) • Master in/slave out (MISO) An SPI transfer is initiated in the master SPI device by reading the SPI status register (SPIxS) when SPTEF= 1 and then writing data to the transmit data buffer (write to SPIxDH:SPIxDL). When a transfer is complete, received data is moved into the receive data buffer. The SPIxDH:SPIxDL registers act as the SPI receive data buffer for reads and as the SPI transmit data buffer for writes. The clock phase control bit (CPHA) and a clock polarity control bit (CPOL) in the SPI Control Register 1 (SPIxC1) select one of four possible clock formats to be used by the SPI system. The CPOL bit simply selects a non-inverted or inverted clock. The CPHA bit is used to accommodate two fundamentally different protocols by sampling data on odd numbered SPSCK edges or on even numbered SPSCK edges. The SPI can be configured to operate as a master or as a slave. When the MSTR bit in SPI control register 1 is set, master mode is selected, when the MSTR bit is clear, slave mode is selected. 15.4.2 Master Mode The SPI operates in master mode when the MSTR bit is set. Only a master SPI module can initiate transmissions. A transmission begins by reading the SPIxS register while SPTEF = 1 and writing to the master SPI data registers. If the shift register is empty, the byte immediately transfers to the shift register. The data begins shifting out on the MOSI pin under the control of the serial clock. • SPSCK The SPR2, SPR1, and SPR0 baud rate selection bits in conjunction with the SPPR2, SPPR1, and SPPR0 baud rate preselection bits in the SPI Baud Rate register control the baud rate generator and determine the speed of the transmission. The SPSCK pin is the SPI clock output. Through the SPSCK pin, the baud rate generator of the master controls the shift register of the slave peripheral. • MOSI, MISO pin In master mode, the function of the serial data output pin (MOSI) and the serial data input pin (MISO) is determined by the SPC0 and BIDIROE control bits. • SS pin If MODFEN and SSOE bit are set, the SS pin is configured as slave select output. The SS output becomes low during each transmission and is high when the SPI is in idle state. If MODFEN is set and SSOE is cleared, the SS pin is configured as input for detecting mode fault error. If the SS input becomes low this indicates a mode fault error where another master tries to drive the MOSI MC9S08JM60 Series Data Sheet, Rev. 5 254 Freescale Semiconductor

Serial Peripheral Interface (S08SPI16V1) and SPSCK lines. In this case, the SPI immediately switches to slave mode, by clearing the MSTR bit and also disables the slave output buffer MISO (or SISO in bidirectional mode). So the result is that all outputs are disabled and SPSCK, MOSI and MISO are inputs. If a transmission is in progress when the mode fault occurs, the transmission is aborted and the SPI is forced into idle state. This mode fault error also sets the mode fault (MODF) flag in the SPI Status Register (SPIxS). If the SPI interrupt enable bit (SPIE) is set when the MODF flag gets set, then an SPI interrupt sequence is also requested. When a write to the SPI Data Register in the master occurs, there is a half SPSCK-cycle delay. After the delay, SPSCK is started within the master. The rest of the transfer operation differs slightly, depending on the clock format specified by the SPI clock phase bit, CPHA, in SPI Control Register 1 (see Section15.4.5, “SPI Clock Formats.”) NOTE A change of the bits CPOL, CPHA, SSOE, LSBFE, MODFEN, SPC0, BIDIROE with SPC0 set, SPIMODE, SPPR2-SPPR0 and SPR2-SPR0 in master mode will abort a transmission in progress and force the SPI into idle state. The remote slave cannot detect this, therefore the master has to ensure that the remote slave is set back to idle state. 15.4.3 Slave Mode The SPI operates in slave mode when the MSTR bit in SPI Control Register1 is clear. • SPSCK In slave mode, SPSCK is the SPI clock input from the master. • MISO, MOSI pin In slave mode, the function of the serial data output pin (MISO) and serial data input pin (MOSI) is determined by the SPC0 bit and BIDIROE bit in SPI Control Register 2. • SS pin The SS pin is the slave select input. Before a data transmission occurs, the SS pin of the slave SPI must be low. SS must remain low until the transmission is complete. If SS goes high, the SPI is forced into idle state. The SS input also controls the serial data output pin, if SS is high (not selected), the serial data output pin is high impedance, and, if SS is low the first bit in the SPI Data Register is driven out of the serial data output pin. Also, if the slave is not selected (SS is high), then the SPSCK input is ignored and no internal shifting of the SPI shift register takes place. Although the SPI is capable of duplex operation, some SPI peripherals are capable of only receiving SPI data in a slave mode. For these simpler devices, there is no serial data out pin. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 255

Serial Peripheral Interface (S08SPI16V1) NOTE When peripherals with duplex capability are used, take care not to simultaneously enable two receivers whose serial outputs drive the same system slave’s serial data output line. As long as no more than one slave device drives the system slave’s serial data output line, it is possible for several slaves to receive the same transmission from a master, although the master would not receive return information from all of the receiving slaves. If the CPHA bit in SPI Control Register 1 is clear, odd numbered edges on the SPSCK input cause the data at the serial data input pin to be latched. Even numbered edges cause the value previously latched from the serial data input pin to shift into the LSB or MSB of the SPI shift register, depending on the LSBFE bit. If the CPHA bit is set, even numbered edges on the SPSCK input cause the data at the serial data input pin to be latched. Odd numbered edges cause the value previously latched from the serial data input pin to shift into the LSB or MSB of the SPI shift register, depending on the LSBFE bit. When CPHA is set, the first edge is used to get the first data bit onto the serial data output pin. When CPHA is clear and the SS input is low (slave selected), the first bit of the SPI data is driven out of the serial data output pin. After the eighth (SPIMODE=0) or sixteenth (SPIMODE= 1) shift, the transfer is considered complete and the received data is transferred into the SPI data registers. To indicate transfer is complete, the SPRF flag in the SPI Status Register is set. NOTE A change of the bits CPOL, CPHA, SSOE, LSBFE, MODFEN, SPC0 and BIDIROE with SPC0 set and SPIMODE in slave mode will corrupt a transmission in progress and has to be avoided. 15.4.4 Data Transmission Length The SPI can support data lengths of 8 or 16 bits. The length can be configured with the SPIMODE bit in the SPIxC2 register. In 8-bit mode (SPIMODE = 0), the SPI Data Register is comprised of one byte: SPIxDL. The SPI Match Register is also comprised of only one byte: SPIxML. Reads of SPIxDH and SPIxMH will return zero. Writes to SPIxDH and SPIxMH will be ignored. In 16-bit mode (SPIMODE = 1), the SPI Data Register is comprised of two bytes: SPIxDH and SPIxDL. Reading either byte (SPIxDH or SPIxDL) latches the contents of both bytes into a buffer where they remain latched until the other byte is read. Writing to either byte (SPIxDH or SPIxDL) latches the value into a buffer. When both bytes have been written, they are transferred as a coherent 16-bit value into the transmit data buffer. In 16-bit mode, the SPI Match Register is also comprised of two bytes: SPIxMH and SPIxML. Reading either byte (SPIxMH or SPIxML) latches the contents of both bytes into a buffer where they remain latched until the other byte is read. Writing to either byte (SPIxMH or SPIxML) latches the value into a buffer. When both bytes have been written, they are transferred as a coherent 16-bit value into the transmit data buffer. MC9S08JM60 Series Data Sheet, Rev. 5 256 Freescale Semiconductor

Serial Peripheral Interface (S08SPI16V1) Any switching between 8- and 16-bit data transmission length (controlled by SPIMODE bit) in master mode will abort a transmission in progress, force the SPI system into idle state, and reset all status bits in the SPIxS register. To initiate a transfer after writing to SPIMODE, the SPIxS register must be read with SPTEF = 1, and data must be written to SPIxDH:SPIxDL in 16-bit mode (SPIMODE = 1) or SPIxDL in 8-bit mode (SPIMODE = 0). In slave mode, user software should write to SPIMODE only once to prevent corrupting a transmission in progress. NOTE Data can be lost if the data length is not the same for both master and slave devices. 15.4.5 SPI Clock Formats To accommodate a wide variety of synchronous serial peripherals from different manufacturers, the SPI system has a clock polarity (CPOL) bit and a clock phase (CPHA) control bit to select one of four clock formats for data transfers. CPOL selectively inserts an inverter in series with the clock. CPHA chooses between two different clock phase relationships between the clock and data. Figure 15-13 shows the clock formats when SPIMODE = 0 (8-bit mode) and CPHA = 1. At the top of the figure, the eight bit times are shown for reference with bit 1 starting at the first SPSCK edge and bit 8 ending one-half SPSCK cycle after the sixteenth SPSCK edge. The MSB first and LSB first lines show the order of SPI data bits depending on the setting in LSBFE. Both variations of SPSCK polarity are shown, but only one of these waveforms applies for a specific transfer, depending on the value in CPOL. The SAMPLE IN waveform applies to the MOSI input of a slave or the MISO input of a master. The MOSI waveform applies to the MOSI output pin from a master and the MISO waveform applies to the MISO output from a slave. The SS OUT waveform applies to the slave select output from a master (provided MODFEN and SSOE=1). The master SS output goes to active low one-half SPSCK cycle before the start of the transfer and goes back high at the end of the eighth bit time of the transfer. The SSIN waveform applies to the slave select input of a slave. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 257

Serial Peripheral Interface (S08SPI16V1) BIT TIME # (REFERENCE) 1 2 ... 6 7 8 SPSCK (CPOL=0) SPSCK (CPOL=1) SAMPLE IN (MISO OR MOSI) MOSI (MASTER OUT) MSB FIRST BIT 7 BIT 6 ... BIT 2 BIT 1 BIT 0 LSB FIRST BIT 0 BIT 1 ... BIT 5 BIT 6 BIT 7 MISO (SLAVE OUT) SS OUT (MASTER) SS IN (SLAVE) Figure15-13. SPI Clock Formats (CPHA = 1) When CPHA =1, the slave begins to drive its MISO output when SS goes to active low, but the data is not defined until the first SPSCK edge. The first SPSCK edge shifts the first bit of data from the shifter onto the MOSI output of the master and the MISO output of the slave. The next SPSCK edge causes both the master and the slave to sample the data bit values on their MISO and MOSI inputs, respectively. At the third SPSCK edge, the SPI shifter shifts one bit position which shifts in the bit value that was just sampled, and shifts the second data bit value out the other end of the shifter to the MOSI and MISO outputs of the master and slave, respectively. When CPHA= 1, the slave’s SS input is not required to go to its inactive high level between transfers. Figure 15-14 shows the clock formats when SPIMODE = 0 and CPHA = 0. At the top of the figure, the eight bit times are shown for reference with bit 1 starting as the slave is selected (SS IN goes low), and bit 8 ends at the last SPSCK edge. The MSB first and LSB first lines show the order of SPI data bits depending on the setting in LSBFE. Both variations of SPSCK polarity are shown, but only one of these waveforms applies for a specific transfer, depending on the value in CPOL. The SAMPLE IN waveform applies to the MOSI input of a slave or the MISO input of a master. The MOSI waveform applies to the MOSI output pin from a master and the MISO waveform applies to the MISO output from a slave. The SS OUT waveform applies to the slave select output from a master (provided MODFEN and SSOE= 1). The master SS output goes to active low at the start of the first bit time of the transfer and goes back high one-half MC9S08JM60 Series Data Sheet, Rev. 5 258 Freescale Semiconductor

Serial Peripheral Interface (S08SPI16V1) SPSCK cycle after the end of the eighth bit time of the transfer. The SS IN waveform applies to the slave select input of a slave. BIT TIME # (REFERENCE) 1 2 ... 6 7 8 SPSCK (CPOL=0) SPSCK (CPOL=1) SAMPLE IN (MISO OR MOSI) MOSI (MASTER OUT) MSB FIRST BIT 7 BIT 6 ... BIT 2 BIT 1 BIT 0 LSB FIRST BIT 0 BIT 1 ... BIT 5 BIT 6 BIT 7 MISO (SLAVE OUT) SS OUT (MASTER) SS IN (SLAVE) Figure15-14. SPI Clock Formats (CPHA = 0) When CPHA= 0, the slave begins to drive its MISO output with the first data bit value (MSB or LSB depending on LSBFE) when SS goes to active low. The first SPSCK edge causes both the master and the slave to sample the data bit values on their MISO and MOSI inputs, respectively. At the second SPSCK edge, the SPI shifter shifts one bit position which shifts in the bit value that was just sampled and shifts the second data bit value out the other end of the shifter to the MOSI and MISO outputs of the master and slave, respectively. When CPHA= 0, the slave’s SS input must go to its inactive high level between transfers. 15.4.6 SPI Baud Rate Generation As shown in Figure 15-15, the clock source for the SPI baud rate generator is the bus clock. The three prescale bits (SPPR2:SPPR1:SPPR0) choose a prescale divisor of 1, 2, 3, 4, 5, 6, 7, or 8. The three rate select bits (SPR2:SPR1:SPR0) divide the output of the prescaler stage by 2, 4, 8, 16, 32, 64, 128, or 256 to get the internal SPI master mode bit-rate clock. The baud rate generator is activated only when the SPI is in the master mode and a serial transfer is taking place. In the other cases, the divider is disabled to decrease I current. DD MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 259

Serial Peripheral Interface (S08SPI16V1) The baud rate divisor equation is as follows: (SPR+1) BaudRateDivisor = (SPPR+1)ξ2 The baud rate can be calculated with the following equation: BusClock Baud Rate = --------------------------------------------- BaudRateDivisor PRESCALER BAUD RATE DIVIDER DIVIDE BY DIVIDE BY MASTER BUS CLOCK SPI 1, 2, 3, 4, 5, 6, 7, or 8 2, 4, 8, 16, 32, 64, 128, or 256 BIT RATE SPPR2:SPPR1:SPPR0 SPR2:SPR1:SPR0 Figure15-15. SPI Baud Rate Generation 15.4.7 Special Features 15.4.7.1 SS Output The SS output feature automatically drives the SS pin low during transmission to select external devices and drives it high during idle to deselect external devices. When SS output is selected, the SS output pin is connected to the SS input pin of the external device. The SS output is available only in master mode during normal SPI operation by asserting the SSOE and MODFEN bits as shown in Table 15-2. The mode fault feature is disabled while SS output is enabled. NOTE Care must be taken when using the SS output feature in a multi-master system since the mode fault feature is not available for detecting system errors between masters. 15.4.7.2 Bidirectional Mode (MOMI or SISO) The bidirectional mode is selected when the SPC0 bit is set in SPI Control Register 2 (see Table 15-9.) In this mode, the SPI uses only one serial data pin for the interface with external device(s). The MSTR bit decides which pin to use. The MOSI pin becomes the serial data I/O (MOMI) pin for the master mode, and the MISO pin becomes serial data I/O (SISO) pin for the slave mode. The MISO pin in master mode and MOSI pin in slave mode are not used by the SPI. MC9S08JM60 Series Data Sheet, Rev. 5 260 Freescale Semiconductor

Serial Peripheral Interface (S08SPI16V1) Table15-9. Normal Mode and Bidirectional Mode When SPE = 1 Master Mode MSTR = 1 Slave Mode MSTR = 0 Serial Out MOSI Serial In MOSI Normal Mode SPI SPI SPC0 = 0 Serial In MISO Serial Out MISO Serial Out MOMI Serial In BIDIROE Bidirectional Mode SPI BIDIROE SPI SPC0 = 1 Serial In Serial Out SISO . The direction of each serial I/O pin depends on the BIDIROE bit. If the pin is configured as an output, serial data from the shift register is driven out on the pin. The same pin is also the serial input to the shift register. The SPSCK is output for the master mode and input for the slave mode. The SS is the input or output for the master mode, and it is always the input for the slave mode. The bidirectional mode does not affect SPSCK and SS functions. NOTE In bidirectional master mode, with mode fault enabled, both data pins MISO and MOSI can be occupied by the SPI, though MOSI is normally used for transmissions in bidirectional mode and MISO is not used by the SPI. If a mode fault occurs, the SPI is automatically switched to slave mode, in this case MISO becomes occupied by the SPI and MOSI is not used. This has to be considered, if the MISO pin is used for another purpose. 15.4.8 Error Conditions The SPI has one error condition: • Mode fault error 15.4.8.1 Mode Fault Error If the SS input becomes low while the SPI is configured as a master, it indicates a system error where more than one master may be trying to drive the MOSI and SPSCK lines simultaneously. This condition is not permitted in normal operation, and the MODF bit in the SPI status register is set automatically provided the MODFEN bit is set. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 261

Serial Peripheral Interface (S08SPI16V1) In the special case where the SPI is in master mode and MODFEN bit is cleared, the SS pin is not used by the SPI. In this special case, the mode fault error function is inhibited and MODF remains cleared. In case the SPI system is configured as a slave, the SS pin is a dedicated input pin. Mode fault error doesn’t occur in slave mode. If a mode fault error occurs the SPI is switched to slave mode, with the exception that the slave output buffer is disabled. So SPSCK, MISO and MOSI pins are forced to be high impedance inputs to avoid any possibility of conflict with another output driver. A transmission in progress is aborted and the SPI is forced into idle state. If the mode fault error occurs in the bidirectional mode for a SPI system configured in master mode, output enable of the MOMI (MOSI in bidirectional mode) is cleared if it was set. No mode fault error occurs in the bidirectional mode for the SPI system configured in slave mode. The mode fault flag is cleared automatically by a read of the SPI Status Register (with MODF set) followed by a write to SPI Control Register 1. If the mode fault flag is cleared, the SPI becomes a normal master or slave again. 15.4.9 Low Power Mode Options 15.4.9.1 SPI in Run Mode In run mode with the SPI system enable (SPE) bit in the SPI control register clear, the SPI system is in a low-power, disabled state. SPI registers can still be accessed, but clocks to the core of this module are disabled. 15.4.9.2 SPI in Wait Mode SPI operation in wait mode depends upon the state of the SPISWAI bit in SPI Control Register 2. • If SPISWAI is clear, the SPI operates normally when the CPU is in wait mode • If SPISWAI is set, SPI clock generation ceases and the SPI module enters a power conservation state when the CPU is in wait mode. — If SPISWAI is set and the SPI is configured for master, any transmission and reception in progress stops at wait mode entry. The transmission and reception resumes when the SPI exits wait mode. – If SPISWAI is set and the SPI is configured as a slave, any transmission and reception in progress continues if the SPSCK continues to be driven from the master. This keeps the slave synchronized to the master and the SPSCK. If the master transmits data while the slave is in wait mode, the slave will continue to send out data consistent with the operation mode at the start of wait mode (i.e., if the slave is currently sending its SPIxDH:SPIxDL to the master, it will continue to send the same byte. Otherwise, if the slave is currently sending the last data received byte from the master, it will continue to send each previously receive data from the master byte). MC9S08JM60 Series Data Sheet, Rev. 5 262 Freescale Semiconductor

Serial Peripheral Interface (S08SPI16V1) NOTE Care must be taken when expecting data from a master while the slave is in wait or stop3 mode. Even though the shift register will continue to operate, the rest of the SPI is shut down (i.e. a SPRF interrupt will not be generated until exiting stop or wait mode). Also, the data from the shift register will not be copied into the SPIxDH:SPIxDL registers until after the slave SPI has exited wait or stop mode. A SPRF flag and SPIxDH:SPIxDL copy is only generated if wait mode is entered or exited during a tranmission. If the slave enters wait mode in idle mode and exits wait mode in idle mode, neither a SPRF nor a SPIxDH:SPIxDL copy will occur. 15.4.9.3 SPI in Stop Mode Stop3 mode is dependent on the SPI system. Upon entry to stop3 mode, the SPI module clock is disabled (held high or low). If the SPI is in master mode and exchanging data when the CPU enters stop mode, the transmission is frozen until the CPU exits stop mode. After stop, data to and from the external SPI is exchanged correctly. In slave mode, the SPI will stay synchronized with the master. The stop mode is not dependent on the SPISWAI bit. In all other stop modes, the SPI module is completely disabled. After stop, all registers are reset to their default values, and the SPI module must be re-initialized. 15.4.9.4 Reset The reset values of registers and signals are described in Section15.3, “Register Definition.” which details the registers and their bit-fields. • If a data transmission occurs in slave mode after reset without a write to SPIxDH:SPIxDL, it will transmit garbage, or the data last received from the master before the reset. • Reading from the SPIxDH:SPIxDL after reset will always read zeros. 15.4.9.5 Interrupts The SPI only originates interrupt requests when the SPI is enabled (SPE bit in SPIxC1 set). The following is a description of how the SPI makes a request and how the MCU should acknowledge that request. The interrupt vector offset and interrupt priority are chip dependent. 15.4.10 SPI Interrupts There are four flag bits, three interrupt mask bits, and one interrupt vector associated with the SPI system. The SPI interrupt enable mask (SPIE) enables interrupts from the SPI receiver full flag (SPRF) and mode fault flag (MODF). The SPI transmit interrupt enable mask (SPTIE) enables interrupts from the SPI transmit buffer empty flag (SPTEF). The SPI match interrupt enable mask bit (SPIMIE) enables interrupts from the SPI match flag (SPMF). When one of the flag bits is set, and the associated interrupt mask bit is set, a hardware interrupt request is sent to the CPU. If the interrupt mask bits are cleared, software can poll the associated flag bits instead of using interrupts. The SPI interrupt service routine (ISR) should check MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 263

Serial Peripheral Interface (S08SPI16V1) the flag bits to determine what event caused the interrupt. The service routine should also clear the flag bit(s) before returning from the ISR (usually near the beginning of the ISR). 15.4.10.1 MODF MODF occurs when the master detects an error on the SS pin. The master SPI must be configured for the MODF feature (see Table 15-2). Once MODF is set, the current transfer is aborted and the following bit is changed: • MSTR=0, The master bit in SPIxC1 resets. The MODF interrupt is reflected in the status register MODF flag. Clearing the flag will also clear the interrupt. This interrupt will stay active while the MODF flag is set. MODF has an automatic clearing process which is described in Section15.3.4, “SPI Status Register (SPIxS).” 15.4.10.2 SPRF SPRF occurs when new data has been received and copied to the SPI receive data buffer. In 8-bit mode, SPRF is set only after all 8 bits have been shifted out of the shift register and into SPIxDL. In 16-bit mode, SPRF is set only after all 16 bits have been shifted out of the shift register and into SPIxDH:SPIxDL. Once SPRF is set, it does not clear until it is serviced. SPRF has an automatic clearing process which is described in Section15.3.4, “SPI Status Register (SPIxS).” In the event that the SPRF is not serviced before the end of the next transfer (i.e. SPRF remains active throughout another transfer), the latter transfers will be ignored and no new data will be copied into the SPIxDH:SPIxDL. 15.4.10.3 SPTEF SPTEF occurs when the SPI transmit buffer is ready to accept new data. In 8-bit mode, SPTEF is set only after all 8 bits have been moved from SPIxDL into the shifter. In 16-bit mode, SPTEF is set only after all 16 bits have been moved from SPIxDH:SPIxDL into the shifter. Once SPTEF is set, it does not clear until it is serviced. SPTEF has an automatic clearing process which is described in Section15.3.4, “SPI Status Register (SPIxS). 15.4.10.4 SPMF SPMF occurs when the data in the receive data buffer is equal to the data in the SPI match register. In 8-bit mode, SPMF is set only after bits 8–0 in the receive data buffer are determined to be equivalent to the value in SPIxML. In 16-bit mode, SPMF is set after bits 15–0 in the receive data buffer are determined to be equivalent to the value in SPIxMH:SPIxML. MC9S08JM60 Series Data Sheet, Rev. 5 264 Freescale Semiconductor

Serial Peripheral Interface (S08SPI16V1) 15.5 Initialization/Application Information 15.5.1 SPI Module Initialization Example 15.5.1.1 Initialization Sequence Before the SPI module can be used for communication, an initialization procedure must be carried out, as follows: 1. Update control register 1 (SPIxC1) to enable the SPI and to control interrupt enables. This register also sets the SPI as master or slave, determines clock phase and polarity, and configures the main SPI options. 2. Update control register 2 (SPIxC2) to enable additional SPI functions such as the SPI match interrupt feature, the master mode-fault function, and bidirectional mode output. 8- or 16-bit mode select and other optional features are controlled here as well. 3. Update the baud rate register (SPIxBR) to set the prescaler and bit rate divisor for an SPI master. 4. Update the hardware match register (SPIxMH:SPIxML) with the value to be compared to the receive data register for triggering an interrupt if hardware match interrupts are enabled. 5. In the master, read SPIxS while SPTEF = 1, and then write to the transmit data register (SPIxDH:SPIxDL) to begin transfer. 15.5.1.2 Pseudo—Code Example In this example, the SPI module will be set up for master mode with only hardware match interrupts enabled. The SPI will run in 16-bit mode at a maximum baud rate of bus clock divided by 2. Clock phase and polarity will be set for an active-high SPI clock where the first edge on SPSCK occurs at the start of the first cycle of a data transfer. SPIxC1=0x54(%01010100) Bit 7 SPIE = 0 Disables receive and mode fault interrupts Bit 6 SPE = 1 Enables the SPI system Bit 5 SPTIE = 0 Disables SPI transmit interrupts Bit 4 MSTR = 1 Sets the SPI module as a master SPI device Bit 3 CPOL = 0 Configures SPI clock as active-high Bit 2 CPHA = 1 First edge on SPSCK at start of first data transfer cycle Bit 1 SSOE = 0 Determines SS pin function when mode fault enabled Bit 0 LSBFE = 0 SPI serial data transfers start with most significant bit MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 265

Serial Peripheral Interface (S08SPI16V1) SPIxC2 = 0xC0(%11000000) Bit 7 SPMIE = 1 SPI hardware match interrupt enabled Bit 6 SPIMODE = 1 Configures SPI for 16-bit mode Bit 5 = 0 Unimplemented Bit 4 MODFEN = 0 Disables mode fault function Bit 3 BIDIROE = 0 SPI data I/O pin acts as input Bit 2 = 0 Unimplemented Bit 1 SPISWAI = 0 SPI clocks operate in wait mode Bit 0 SPC0 = 0 uses separate pins for data input and output SPIxBR = 0x00(%00000000) Bit 7 = 0 Unimplemented Bit 6:4 = 000 Sets prescale divisor to 1 Bit 3 = 0 Unimplemented Bit 2:0 = 000 Sets baud rate divisor to 2 SPIxS = 0x00(%00000000) Bit 7 SPRF = 0 Flag is set when receive data buffer is full Bit 6 SPMF = 0 Flag is set when SPIMH/L = receive data buffer Bit 5 SPTEF = 0 Flag is set when transmit data buffer is empty Bit 4 MODF = 0 Mode fault flag for master mode Bit 3:0 = 0 Unimplemented SPIxMH = 0xXX In 16-bit mode, this register holds bits 8–15 of the hardware match buffer. In 8-bit mode, writes to this register will be ignored. SPIxML = 0xXX Holds bits 0–7 of the hardware match buffer. SPIxDH = 0xxx In 16-bit mode, this register holds bits 8–15 of the data to be transmitted by the transmit buffer and received by the receive buffer. SPIxDL = 0xxx Holds bits 0–7 of the data to be transmitted by the transmit buffer and received by the receive buffer. MC9S08JM60 Series Data Sheet, Rev. 5 266 Freescale Semiconductor

Serial Peripheral Interface (S08SPI16V1) RESET INITIALIZE SPI SPIxC1 = 0x54 SPIxC2 = 0xC0 SPIxBR = 0x00 SPIxMH = 0xXX YES SPTEF = 1 NO ? YES WRITE TO SPIxDH:SPIxDL SPRF = 1 NO ? YES READ SPIxDH:SPIxDL SPMF = 1 NO ? YES READ SPMF WHILE SET TO CLEAR FLAG, THEN WRITE A 1 TO IT CONTINUE Figure15-16. Initialization Flowchart Example for SPI Master Device in 16-bit Mode MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 267

Serial Peripheral Interface (S08SPI16V1) MC9S08JM60 Series Data Sheet, Rev. 5 268 Freescale Semiconductor

Chapter 16 Timer/Pulse-Width Modulator (S08TPMV3) 16.1 Introduction The MC9S08JM60 series includes two independent timer/PWM (TPM) modules which support traditional input capture, output compare, or buffered edge-aligned pulse-width modulation (PWM) on each channel. A control bit in each TPM configures all channels in that timer to operate as center-aligned PWM functions. In each of these two TPMs, timing functions are based on a separate 16-bit counter with prescaler and modulo features to control frequency and range (period between overflows) of the time reference. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 269

Chapter16 Timer/Pulse-Width Modulator (S08TPMV3) USBDP ON-CHIP ICE AND USBDN HCS08 CORE DEBUG MODULE (DBG) A T 6 R PTA5– PTA0 O USB SIE P BKGD/MS FULL SPEED PTB7/ADP7 BDC CPU USB PTB6/ADP6 USB ENDPOINT TRANSCEIVER PTB5/KBIP5/ADP5 RAM B T PTB4/KBIP4/ADP4 SSPSS2CK2 POR PTB3/SS2/ADP3 RESET HCS08 SYSTEM CONTROL 8-/16-BIT SERIAL PERIPHERAL MOSI2 PTB2/SPSCK2/ADP2 INTERFACE MODULE (SPI2) PTB1/MOSI2/ADP1 MISO2 PTB0/MISO2/ADP0 RESETS AND INTERRUPTS MODES OF OPERATION PTC6 IRQ/TPMCLK POWER MANAGEMENT SERIAL COMMUNICATIONS RxD2 PTC5/RxD2 COP IRQ LVD INTERFACE MODULE (SCI2) TxD2 ORT C PPTTCC34/TxD2 P PTC2 SDA PTC1/SDA IIC MODULE (IIC) SCL PTC0/SCL VDDAD 12-CHANNEL, 12-BIT 8 PTD7 VSSAD ANALOG-TO-DIGITAL 4 PTD6 VREFL CONVERTER (ADC) PTD5 VREFH D PTD4/ADP11 T R PTD3/KBIP3/ADP10 O USER Flash (IN BYTES) P PTD2/KBIP2/ACMPO ACMP– MC9S08JM60 = 60,912 PTD1/ADP9/ACMP– MC9S08JM32 = 32,768 ANALOG COMPARATOR ACMP+ PTD0/ADP8/ACMP+ (ACMP) ACMPO SS1 PTE7/SS1 USER RAM (IN BYTES) SPSCK1 8-/16-BIT SERIAL PERIPHERAL PTE6/SPSCK1 MMCC99SS0088JJMM6302 == 42009468 INTERFACE MODULE (SPI1) MOSI1 PTE5/MOSI1 MISO1 PTE4/MISO1 TPMCLK E MULTI-PURPOSE CLOCK 6-CHMAONDNUELLE T (ITMPEMR1/P)WM TTPPMM11CCHH10 PORT PTE3/TPM1CH1 GENERATOR (MCG) PTE2/TPM1CH0 TPM1CHx4 RxD1 SERIAL COMMUNICATIONS PTE1/RxD1 VSSOSC LOW-POWER OSCILLATOR TxD1 PTE0/TxD1 INTERFACE MODULE (SCI1) PTF7 VDD SYSTEM TPMCLK PTF6 VSS RVEOGLUTLAAGTEO R 2-CHMAONDNUELLE T (ITMPEMR2/P)WM TTPPMM22CCHH10 T F PPTTFF54//TTPPMM22CCHH10 OR PTF3/TPM1CH5 KBIPx P PTF2/TPM1CH4 VUSB33 USB 3.3-V VOLTAGE REGULATOR 8-BIT KEYBOARD 4 PTF1/TPM1CH3 INTERRUPT MODULE (KBI) KBIPx 4 PTF0/TPM1CH2 REAL-TIME COUNTER (RTC) EXTAL PTG5/EXTAL XTAL NOTES: G PTG4/XTAL 1. Port pins are software configurable with pullup device if input port. RT PTG3/KBIP7 O PTG2/KBIP6 2. Pin contains software configurable pullup/pull-down device if IRQ is enabled P PTG1/KBIP1 (IRQPE=1). Pull-down is enabled if rising edge detect is selected (IRQEDG=1) PTG0/KBIP0 3. IRQ does not have a clamp diode to V . IRQ must not be driven above V . DD DD 4. Pin contains integrated pullup device. 5. When pin functions as KBI (KBIPEn = 1) and associated pin is configured to enable the pullup device, KBEDGn can be used to reconfigure the pullup as a pull-down device. Figure16-1. MC9S08JM60 Series Block Diagram Highlighting the TPM Blocks and Pins MC9S08JM60 Series Data Sheet, Rev. 5 270 Freescale Semiconductor

Timer/PWM Module (S08TPMV3) 16.1.1 Features The TPM includes these distinctive features: • One to eight channels: — Each channel may be input capture, output compare, or edge-aligned PWM — Rising-Edge, falling-edge, or any-edge input capture trigger — Set, clear, or toggle output compare action — Selectable polarity on PWM outputs • Module may be configured for buffered, center-aligned pulse-width-modulation (CPWM) on all channels • Timer clock source selectable as prescaled bus clock, fixed system clock, or an external clock pin — Prescale taps for divide-by 1, 2, 4, 8, 16, 32, 64, or 128 — Fixed system clock source are synchronized to the bus clock by an on-chip synchronization circuit — External clock pin may be shared with any timer channel pin or a separated input pin • 16-bit free-running or modulo up/down count operation • Timer system enable • One interrupt per channel plus terminal count interrupt 16.1.2 Modes of Operation In general, TPM channels may be independently configured to operate in input capture, output compare, or edge-aligned PWM modes. A control bit allows the whole TPM (all channels) to switch to center-aligned PWM mode. When center-aligned PWM mode is selected, input capture, output compare, and edge-aligned PWM functions are not available on any channels of this TPM module. When the microcontroller is in active BDM background or BDM foreground mode, the TPM temporarily suspends all counting until the microcontroller returns to normal user operating mode. During stop mode, all system clocks, including the main oscillator, are stopped; therefore, the TPM is effectively disabled until clocks resume. During wait mode, the TPM continues to operate normally. Provided the TPM does not need to produce a real time reference or provide the interrupt source(s) needed to wake the MCU from wait mode, the user can save power by disabling TPM functions before entering wait mode. • Input capture mode When a selected edge event occurs on the associated MCU pin, the current value of the 16-bit timer counter is captured into the channel value register and an interrupt flag bit is set. Rising edges, falling edges, any edge, or no edge (disable channel) may be selected as the active edge which triggers the input capture. • Output compare mode When the value in the timer counter register matches the channel value register, an interrupt flag bit is set, and a selected output action is forced on the associated MCU pin. The output compare action may be selected to force the pin to zero, force the pin to one, toggle the pin, or ignore the pin (used for software timing functions). MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 271

Timer/PWM Module (S08TPMV3) • Edge-aligned PWM mode The value of a 16-bit modulo register plus 1 sets the period of the PWM output signal. The channel value register sets the duty cycle of the PWM output signal. The user may also choose the polarity of the PWM output signal. Interrupts are available at the end of the period and at the duty-cycle transition point. This type of PWM signal is called edge-aligned because the leading edges of all PWM signals are aligned with the beginning of the period, which is the same for all channels within a TPM. • Center-aligned PWM mode Twice the value of a 16-bit modulo register sets the period of the PWM output, and the channel-value register sets the half-duty-cycle duration. The timer counter counts up until it reaches the modulo value and then counts down until it reaches zero. As the count matches the channel value register while counting down, the PWM output becomes active. When the count matches the channel value register while counting up, the PWM output becomes inactive. This type of PWM signal is called center-aligned because the centers of the active duty cycle periods for all channels are aligned with a count value of zero. This type of PWM is required for types of motors used in small appliances. This is a high-level description only. Detailed descriptions of operating modes are in later sections. 16.1.3 Block Diagram The TPM uses one input/output (I/O) pin per channel, TPMxCHn (timer channel n) where n is the channel number (1-8). The TPM shares its I/O pins with general purpose I/O port pins (refer to I/O pin descriptions in full-chip specification for the specific chip implementation). Figure 16-2 shows the TPM structure. The central component of the TPM is the 16-bit counter that can operate as a free-running counter or a modulo up/down counter. The TPM counter (when operating in normal up-counting mode) provides the timing reference for the input capture, output compare, and edge-aligned PWM functions. The timer counter modulo registers, TPMxMODH:TPMxMODL, control the modulo value of the counter (the values 0x0000 or 0xFFFF effectively make the counter free running). Software can read the counter value at any time without affecting the counting sequence. Any write to either half of the TPMxCNT counter resets the counter, regardless of the data value written. MC9S08JM60 Series Data Sheet, Rev. 5 272 Freescale Semiconductor

Timer/PWM Module (S08TPMV3) BUS CLOCK CLOCK SOURCE PRESCALE AND SELECT SELECT ³1, 2, 4, 8, 16, 32, 64, FIXED SYSTEM CLOCK OFF, BUS, FIXED SYNC or ³128 EXTERNAL CLOCK SYSTEM CLOCK, EXT CLKSB:CLKSA PS2:PS1:PS0 CPWMS 16-BIT COUNTER TOF INTER- COUNTER RESET RUPT TOIE LOGIC 16-BIT COMPARATOR TPMxMODH:TPMxMODL CHANNEL 0 ELS0B ELS0A PORT TPMxCH0 LOGIC 16-BIT COMPARATOR TPMxC0VH:TPMxC0VL CH0F INTER- 16-BIT LATCH RUPT LOGIC MS0B MS0A CH0IE S CHANNEL 1 ELS1B ELS1A PORT TPMxCH1 U LOGIC L B 16-BIT COMPARATOR A N TPMxC1VH:TPMxC1VL CH1F R E INTER- NT 16-BIT LATCH RUPT I LOGIC CH1IE MS1B MS1A Up to 8 channels CHANNEL 7 ELS7B ELS7A PORT TPMxCH7 LOGIC 16-BIT COMPARATOR TPMxC7VH:TPMxC7VL CH7F INTER- 16-BIT LATCH RUPT LOGIC CH7IE MS7B MS7A Figure16-2. TPM Block Diagram MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 273

Timer/PWM Module (S08TPMV3) The TPM channels are programmable independently as input capture, output compare, or edge-aligned PWM channels. Alternately, the TPM can be configured to produce CPWM outputs on all channels. When the TPM is configured for CPWMs, the counter operates as an up/down counter; input capture, output compare, and EPWM functions are not practical. If a channel is configured as input capture, an internal pullup device may be enabled for that channel. The details of how a module interacts with pin controls depends upon the chip implementation because the I/O pins and associated general purpose I/O controls are not part of the module. Refer to the discussion of the I/O port logic in a full-chip specification. Because center-aligned PWMs are usually used to drive 3-phase AC-induction motors and brushless DC motors, they are typically used in sets of three or six channels. 16.2 Signal Description Table 16-1 shows the user-accessible signals for the TPM. The number of channels may be varied from one to eight. When an external clock is included, it can be shared with the same pin as any TPM channel; however, it could be connected to a separate input pin. Refer to the I/O pin descriptions in full-chip specification for the specific chip implementation. Table16-1. Signal Properties Name Function EXTCLK1 External clock source which may be selected to drive the TPM counter. TPMxCHn2 I/O pin associated with TPM channel n 1 When preset, this signal can share any channel pin; however depending upon full-chip implementation, this signal could be connected to a separate external pin. 2 n=channel number (1 to 8) Refer to documentation for the full-chip for details about reset states, port connections, and whether there is any pullup device on these pins. TPM channel pins can be associated with general purpose I/O pins and have passive pullup devices which can be enabled with a control bit when the TPM or general purpose I/O controls have configured the associated pin as an input. When no TPM function is enabled to use a corresponding pin, the pin reverts to being controlled by general purpose I/O controls, including the port-data and data-direction registers. Immediately after reset, no TPM functions are enabled, so all associated pins revert to general purpose I/O control. 16.2.1 Detailed Signal Descriptions This section describes each user-accessible pin signal in detail. Although Table 16-1 grouped all channel pins together, any TPM pin can be shared with the external clock source signal. Since I/O pin logic is not part of the TPM, refer to full-chip documentation for a specific derivative for more details about the interaction of TPM pin functions and general purpose I/O controls including port data, data direction, and pullup controls. MC9S08JM60 Series Data Sheet, Rev. 5 274 Freescale Semiconductor

Timer/PWM Module (S08TPMV3) 16.2.1.1 EXTCLK — External Clock Source Control bits in the timer status and control register allow the user to select nothing (timer disable), the bus-rate clock (the normal default source), a crystal-related clock, or an external clock as the clock which drives the TPM prescaler and subsequently the 16-bit TPM counter. The external clock source is synchronized in the TPM. The bus clock clocks the synchronizer; the frequency of the external source must be no more than one-fourth the frequency of the bus-rate clock, to meet Nyquist criteria and allowing for jitter. The external clock signal shares the same pin as a channel I/O pin, so the channel pin will not be usable for channel I/O function when selected as the external clock source. It is the user’s responsibility to avoid such settings. If this pin is used as an external clock source (CLKSB:CLKSA = 1:1), the channel can still be used in output compare mode as a software timer (ELSnB:ELSnA = 0:0). 16.2.1.2 TPMxCHn — TPM Channel n I/O Pin(s) Each TPM channel is associated with an I/O pin on the MCU. The function of this pin depends on the channel configuration. The TPM pins share with general purpose I/O pins, where each pin has a port data register bit, and a data direction control bit, and the port has optional passive pullups which may be enabled whenever a port pin is acting as an input. The TPM channel does not control the I/O pin when (ELSnB:ELSnA = 0:0) or when (CLKSB:CLKSA = 0:0) so it normally reverts to general purpose I/O control. When CPWMS = 1 (and ELSnB:ELSnA not = 0:0), all channels within the TPM are configured for center-aligned PWM and the TPMxCHn pins are all controlled by the TPM system. When CPWMS=0, the MSnB:MSnA control bits determine whether the channel is configured for input capture, output compare, or edge-aligned PWM. When a channel is configured for input capture (CPWMS=0, MSnB:MSnA = 0:0 and ELSnB:ELSnA not = 0:0), the TPMxCHn pin is forced to act as an edge-sensitive input to the TPM. ELSnB:ELSnA control bits determine what polarity edge or edges will trigger input-capture events. A synchronizer based on the bus clock is used to synchronize input edges to the bus clock. This implies the minimum pulse width—that can be reliably detected—on an input capture pin is four bus clock periods (with ideal clock pulses as near as two bus clocks can be detected). TPM uses this pin as an input capture input to override the port data and data direction controls for the same pin. When a channel is configured for output compare (CPWMS=0, MSnB:MSnA = 0:1 and ELSnB:ELSnA not = 0:0), the associated data direction control is overridden, the TPMxCHn pin is considered an output controlled by the TPM, and the ELSnB:ELSnA control bits determine how the pin is controlled. The remaining three combinations of ELSnB:ELSnA determine whether the TPMxCHn pin is toggled, cleared, or set each time the 16-bit channel value register matches the timer counter. When the output compare toggle mode is initially selected, the previous value on the pin is driven out until the next output compare event—then the pin is toggled. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 275

Timer/PWM Module (S08TPMV3) When a channel is configured for edge-aligned PWM (CPWMS=0, MSnB=1 and ELSnB:ELSnA not = 0:0), the data direction is overridden, the TPMxCHn pin is forced to be an output controlled by the TPM, and ELSnA controls the polarity of the PWM output signal on the pin. When ELSnB:ELSnA=1:0, the TPMxCHn pin is forced high at the start of each new period (TPMxCNT=0x0000), and the pin is forced low when the channel value register matches the timer counter. When ELSnA=1, the TPMxCHn pin is forced low at the start of each new period (TPMxCNT=0x0000), and the pin is forced high when the channel value register matches the timer counter. TPMxMODH:TPMxMODL = 0x0008 TPMxCnVH:TPMxCnVL = 0x0005 TPMxCNTH:TPMxCNTL ... 0 1 2 3 4 5 6 7 8 0 1 2 ... TPMxCHn CHnF BIT TOF BIT Figure16-3. High-True Pulse of an Edge-Aligned PWM TPMxMODH:TPMxMODL = 0x0008 TPMxCnVH:TPMxCnVL = 0x0005 TPMxCNTH:TPMxCNTL ... 0 1 2 3 4 5 6 7 8 0 1 2 ... TPMxCHn CHnF BIT TOF BIT Figure16-4. Low-True Pulse of an Edge-Aligned PWM MC9S08JM60 Series Data Sheet, Rev. 5 276 Freescale Semiconductor

Timer/PWM Module (S08TPMV3) When the TPM is configured for center-aligned PWM (and ELSnB:ELSnA not = 0:0), the data direction for all channels in this TPM are overridden, the TPMxCHn pins are forced to be outputs controlled by the TPM, and the ELSnA bits control the polarity of each TPMxCHn output. If ELSnB:ELSnA=1:0, the corresponding TPMxCHn pin is cleared when the timer counter is counting up, and the channel value register matches the timer counter; the TPMxCHn pin is set when the timer counter is counting down, and the channel value register matches the timer counter. If ELSnA=1, the corresponding TPMxCHn pin is set when the timer counter is counting up and the channel value register matches the timer counter; the TPMxCHn pin is cleared when the timer counter is counting down and the channel value register matches the timer counter. TPMxMODH:TPMxMODL = 0x0008 TPMxCnVH:TPMxCnVL = 0x0005 TPMxCNTH:TPMxCNTL ... 7 8 7 6 5 4 3 2 1 0 1 2 3 4 5 6 7 8 7 6 5 ... TPMxCHn CHnF BIT TOF BIT Figure16-5. High-True Pulse of a Center-Aligned PWM TPMxMODH:TPMxMODL = 0x0008 TPMxCnVH:TPMxCnVL = 0x0005 TPMxCNTH:TPMxCNTL ... 7 8 7 6 5 4 3 2 1 0 1 2 3 4 5 6 7 8 7 6 5 ... TPMxCHn CHnF BIT TOF BIT Figure16-6. Low-True Pulse of a Center-Aligned PWM MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 277

Timer/PWM Module (S08TPMV3) 16.3 Register Definition This section consists of register descriptions in address order. A typical MCU system may contain multiple TPMs, and each TPM may have one to eight channels, so register names include placeholder characters to identify which TPM and which channel is being referenced. For example, TPMxCnSC refers to timer (TPM) x, channel n. TPM1C2SC would be the status and control register for channel 2 of timer 1. 16.3.1 TPM Status and Control Register (TPMxSC) TPMxSC contains the overflow status flag and control bits used to configure the interrupt enable, TPM configuration, clock source, and prescale factor. These controls relate to all channels within this timer module. 7 6 5 4 3 2 1 0 R TOF TOIE CPWMS CLKSB CLKSA PS2 PS1 PS0 W 0 Reset 0 0 0 0 0 0 0 0 Figure16-7. TPM Status and Control Register (TPMxSC) Table16-2. TPMxSC Field Descriptions Field Description 7 Timer overflow flag. This read/write flag is set when the TPM counter resets to 0x0000 after reaching the modulo TOF value programmed in the TPM counter modulo registers. Clear TOF by reading the TPM status and control register when TOF is set and then writing a logic 0 to TOF. If another TPM overflow occurs before the clearing sequence is complete, the sequence is reset so TOF would remain set after the clear sequence was completed for the earlier TOF. This is done so a TOF interrupt request cannot be lost during the clearing sequence for a previous TOF. Reset clears TOF. Writing a logic 1 to TOF has no effect. 0 TPM counter has not reached modulo value or overflow 1 TPM counter has overflowed 6 Timer overflow interrupt enable. This read/write bit enables TPM overflow interrupts. If TOIE is set, an interrupt is TOIE generated when TOF equals one. Reset clears TOIE. 0 TOF interrupts inhibited (use for software polling) 1 TOF interrupts enabled 5 Center-aligned PWM select. When present, this read/write bit selects CPWM operating mode. By default, the TPM CPWMS operates in up-counting mode for input capture, output compare, and edge-aligned PWM functions. Setting CPWMS reconfigures the TPM to operate in up/down counting mode for CPWM functions. Reset clears CPWMS. 0 All channels operate as input capture, output compare, or edge-aligned PWM mode as selected by the MSnB:MSnA control bits in each channel’s status and control register. 1 All channels operate in center-aligned PWM mode. MC9S08JM60 Series Data Sheet, Rev. 5 278 Freescale Semiconductor

Timer/PWM Module (S08TPMV3) Table16-2. TPMxSC Field Descriptions (continued) Field Description 4–3 Clock source selects. As shown in Table16-3, this 2-bit field is used to disable the TPM system or select one of CLKS[B:A] three clock sources to drive the counter prescaler. The fixed system clock source is only meaningful in systems with a PLL-based system clock. When there is no PLL, the fixed-system clock source is the same as the bus rate clock. The external source is synchronized to the bus clock by TPM module, and the fixed system clock source (when a PLL is present) is synchronized to the bus clock by an on-chip synchronization circuit. When a PLL is present but not enabled, the fixed-system clock source is the same as the bus-rate clock. 2–0 Prescale factor select. This 3-bit field selects one of 8 division factors for the TPM clock input as shown in PS[2:0] Table16-4. This prescaler is located after any clock source synchronization or clock source selection so it affects the clock source selected to drive the TPM system. The new prescale factor will affect the clock source on the next system clock cycle after the new value is updated into the register bits. Table16-3. TPM-Clock-Source Selection CLKSB:CLKSA TPM Clock Source to Prescaler Input 00 No clock selected (TPM counter disable) 01 Bus rate clock 10 Fixed system clock 11 External source Table16-4. Prescale Factor Selection PS2:PS1:PS0 TPM Clock Source Divided-by 000 1 001 2 010 4 011 8 100 16 101 32 110 64 111 128 16.3.2 TPM-Counter Registers (TPMxCNTH:TPMxCNTL) The two read-only TPM counter registers contain the high and low bytes of the value in the TPM counter. Reading either byte (TPMxCNTH or TPMxCNTL) latches the contents of both bytes into a buffer where they remain latched until the other half is read. This allows coherent 16-bit reads in either big-endian or little-endian order which makes this more friendly to various compiler implementations. The coherency mechanism is automatically restarted by an MCU reset or any write to the timer status/control register (TPMxSC). Reset clears the TPM counter registers. Writing any value to TPMxCNTH or TPMxCNTL also clears the TPM counter (TPMxCNTH:TPMxCNTL) and resets the coherency mechanism, regardless of the data involved in the write. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 279

Timer/PWM Module (S08TPMV3) 7 6 5 4 3 2 1 0 R Bit 15 14 13 12 11 10 9 Bit 8 W Any write to TPMxCNTH clears the 16-bit counter Reset 0 0 0 0 0 0 0 0 Figure16-8. TPM Counter Register High (TPMxCNTH) 7 6 5 4 3 2 1 0 R Bit 7 6 5 4 3 2 1 Bit 0 W Any write to TPMxCNTL clears the 16-bit counter Reset 0 0 0 0 0 0 0 0 Figure16-9. TPM Counter Register Low (TPMxCNTL) When BDM is active, the timer counter is frozen (this is the value that will be read by user); the coherency mechanism is frozen such that the buffer latches remain in the state they were in when the BDM became active, even if one or both counter halves are read while BDM is active. This assures that if the user was in the middle of reading a 16-bit register when BDM became active, it will read the appropriate value from the other half of the 16-bit value after returning to normal execution. In BDM mode, writing any value to TPMxSC, TPMxCNTH or TPMxCNTL registers resets the read coherency mechanism of the TPMxCNTH:L registers, regardless of the data involved in the write. 16.3.3 TPM Counter Modulo Registers (TPMxMODH:TPMxMODL) The read/write TPM modulo registers contain the modulo value for the TPM counter. After the TPM counter reaches the modulo value, the TPM counter resumes counting from 0x0000 at the next clock, and the overflow flag (TOF) becomes set. Writing to TPMxMODH or TPMxMODL inhibits the TOF bit and overflow interrupts until the other byte is written. Reset sets the TPM counter modulo registers to 0x0000 which results in a free running timer counter (modulo disabled). Writing to either byte (TPMxMODH or TPMxMODL) latches the value into a buffer and the registers are updated with the value of their write buffer according to the value of CLKSB:CLKSA bits, so: • If (CLKSB:CLKSA = 0:0), then the registers are updated when the second byte is written • If (CLKSB:CLKSA not = 0:0), then the registers are updated after both bytes were written, and the TPM counter changes from (TPMxMODH:TPMxMODL - 1) to (TPMxMODH:TPMxMODL). If the TPM counter is a free-running counter, the update is made when the TPM counter changes from 0xFFFE to 0xFFFF The latching mechanism may be manually reset by writing to the TPMxSC address (whether BDM is active or not). When BDM is active, the coherency mechanism is frozen (unless reset by writing to TPMxSC register) such that the buffer latches remain in the state they were in when the BDM became active, even if one or both halves of the modulo register are written while BDM is active. Any write to the modulo registers bypasses the buffer latches and directly writes to the modulo register while BDM is active. MC9S08JM60 Series Data Sheet, Rev. 5 280 Freescale Semiconductor

Timer/PWM Module (S08TPMV3) 7 6 5 4 3 2 1 0 R Bit 15 14 13 12 11 10 9 Bit 8 W Reset 0 0 0 0 0 0 0 0 Figure16-10. TPM Counter Modulo Register High (TPMxMODH) 7 6 5 4 3 2 1 0 R Bit 7 6 5 4 3 2 1 Bit 0 W Reset 0 0 0 0 0 0 0 0 Figure16-11. TPM Counter Modulo Register Low (TPMxMODL) Reset the TPM counter before writing to the TPM modulo registers to avoid confusion about when the first counter overflow will occur. 16.3.4 TPM Channel n Status and Control Register (TPMxCnSC) TPMxCnSC contains the channel-interrupt-status flag and control bits used to configure the interrupt enable, channel configuration, and pin function. 7 6 5 4 3 2 1 0 R CHnF 0 0 CHnIE MSnB MSnA ELSnB ELSnA W 0 Reset 0 0 0 0 0 0 0 0 = Unimplemented or Reserved Figure16-12. TPM Channel n Status and Control Register (TPMxCnSC) MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 281

Timer/PWM Module (S08TPMV3) Table16-5. TPMxCnSC Field Descriptions Field Description 7 Channel n flag. When channel n is an input-capture channel, this read/write bit is set when an active edge occurs CHnF on the channel n pin. When channel n is an output compare or edge-aligned/center-aligned PWM channel, CHnF is set when the value in the TPM counter registers matches the value in the TPM channel n value registers. When channel n is an edge-aligned/center-aligned PWM channel and the duty cycle is set to 0% or 100%, CHnF will not be set even when the value in the TPM counter registers matches the value in the TPM channel n value registers. A corresponding interrupt is requested when CHnF is set and interrupts are enabled (CHnIE = 1). Clear CHnF by reading TPMxCnSC while CHnF is set and then writing a logic 0 to CHnF. If another interrupt request occurs before the clearing sequence is complete, the sequence is reset so CHnF remains set after the clear sequence completed for the earlier CHnF. This is done so a CHnF interrupt request cannot be lost due to clearing a previous CHnF. Reset clears the CHnF bit. Writing a logic 1 to CHnF has no effect. 0 No input capture or output compare event occurred on channel n 1 Input capture or output compare event on channel n 6 Channel n interrupt enable. This read/write bit enables interrupts from channel n. Reset clears CHnIE. CHnIE 0 Channel n interrupt requests disabled (use for software polling) 1 Channel n interrupt requests enabled 5 Mode select B for TPM channel n. When CPWMS=0, MSnB=1 configures TPM channel n for edge-aligned PWM MSnB mode. Refer to the summary of channel mode and setup controls in Table16-6. 4 Mode select A for TPM channel n. When CPWMS=0 and MSnB=0, MSnA configures TPM channel n for MSnA input-capture mode or output compare mode. Refer to Table16-6 for a summary of channel mode and setup controls. Note:If the associated port pin is not stable for at least two bus clock cycles before changing to input capture mode, it is possible to get an unexpected indication of an edge trigger. 3–2 Edge/level select bits. Depending upon the operating mode for the timer channel as set by CPWMS:MSnB:MSnA ELSnB and shown in Table16-6, these bits select the polarity of the input edge that triggers an input capture event, select ELSnA the level that will be driven in response to an output compare match, or select the polarity of the PWM output. Setting ELSnB:ELSnA to 0:0 configures the related timer pin as a general purpose I/O pin not related to any timer functions. This function is typically used to temporarily disable an input capture channel or to make the timer pin available as a general purpose I/O pin when the associated timer channel is set up as a software timer that does not require the use of a pin. MC9S08JM60 Series Data Sheet, Rev. 5 282 Freescale Semiconductor

Timer/PWM Module (S08TPMV3) Table16-6. Mode, Edge, and Level Selection CPWMS MSnB:MSnA ELSnB:ELSnA Mode Configuration X XX 00 Pin not used for TPM - revert to general purpose I/O or other peripheral control 0 00 01 Input capture Capture on rising edge only 10 Capture on falling edge only 11 Capture on rising or falling edge 01 01 Output compare Toggle output on compare 10 Clear output on compare 11 Set output on compare 1X 10 Edge-aligned High-true pulses (clear PWM output on compare) X1 Low-true pulses (set output on compare) 1 XX 10 Center-aligned High-true pulses (clear PWM output on compare-up) X1 Low-true pulses (set output on compare-up) 16.3.5 TPM Channel Value Registers (TPMxCnVH:TPMxCnVL) These read/write registers contain the captured TPM counter value of the input capture function or the output compare value for the output compare or PWM functions. The channel registers are cleared by reset. 7 6 5 4 3 2 1 0 R Bit 15 14 13 12 11 10 9 Bit 8 W Reset 0 0 0 0 0 0 0 0 Figure16-13. TPM Channel Value Register High (TPMxCnVH) 7 6 5 4 3 2 1 0 R Bit 7 6 5 4 3 2 1 Bit 0 W Reset 0 0 0 0 0 0 0 0 Figure16-14. TPM Channel Value Register Low (TPMxCnVL) MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 283

Timer/PWM Module (S08TPMV3) In input capture mode, reading either byte (TPMxCnVH or TPMxCnVL) latches the contents of both bytes into a buffer where they remain latched until the other half is read. This latching mechanism also resets (becomes unlatched) when the TPMxCnSC register is written (whether BDM mode is active or not). Any write to the channel registers will be ignored during the input capture mode. When BDM is active, the coherency mechanism is frozen (unless reset by writing to TPMxCnSC register) such that the buffer latches remain in the state they were in when the BDM became active, even if one or both halves of the channel register are read while BDM is active. This assures that if the user was in the middle of reading a 16-bit register when BDM became active, it will read the appropriate value from the other half of the 16-bit value after returning to normal execution. The value read from the TPMxCnVH and TPMxCnVL registers in BDM mode is the value of these registers and not the value of their read buffer. In output compare or PWM modes, writing to either byte (TPMxCnVH or TPMxCnVL) latches the value into a buffer. After both bytes are written, they are transferred as a coherent 16-bit value into the timer-channel registers according to the value of CLKSB:CLKSA bits and the selected mode, so: • If (CLKSB:CLKSA = 0:0), then the registers are updated when the second byte is written. • If (CLKSB:CLKSA not = 0:0 and in output compare mode) then the registers are updated after the second byte is written and on the next change of the TPM counter (end of the prescaler counting). • If (CLKSB:CLKSA not = 0:0 and in EPWM or CPWM modes), then the registers are updated after the both bytes were written, and the TPM counter changes from (TPMxMODH:TPMxMODL - 1) to (TPMxMODH:TPMxMODL). If the TPM counter is a free-running counter then the update is made when the TPM counter changes from 0xFFFE to 0xFFFF. The latching mechanism may be manually reset by writing to the TPMxCnSC register (whether BDM mode is active or not). This latching mechanism allows coherent 16-bit writes in either big-endian or little-endian order which is friendly to various compiler implementations. When BDM is active, the coherency mechanism is frozen such that the buffer latches remain in the state they were in when the BDM became active even if one or both halves of the channel register are written while BDM is active. Any write to the channel registers bypasses the buffer latches and directly write to the channel register while BDM is active. The values written to the channel register while BDM is active are used for PWM & output compare operation once normal execution resumes. Writes to the channel registers while BDM is active do not interfere with partial completion of a coherency sequence. After the coherency mechanism has been fully exercised, the channel registers are updated using the buffered values written (while BDM was not active) by the user. 16.4 Functional Description All TPM functions are associated with a central 16-bit counter which allows flexible selection of the clock source and prescale factor. There is also a 16-bit modulo register associated with the main counter. The CPWMS control bit chooses between center-aligned PWM operation for all channels in the TPM (CPWMS=1) or general purpose timing functions (CPWMS=0) where each channel can independently be configured to operate in input capture, output compare, or edge-aligned PWM mode. The CPWMS control bit is located in the main TPM status and control register because it affects all channels within the TPM MC9S08JM60 Series Data Sheet, Rev. 5 284 Freescale Semiconductor

Timer/PWM Module (S08TPMV3) and influences the way the main counter operates. (In CPWM mode, the counter changes to an up/down mode rather than the up-counting mode used for general purpose timer functions.) The following sections describe the main counter and each of the timer operating modes (input capture, output compare, edge-aligned PWM, and center-aligned PWM). Because details of pin operation and interrupt activity depend upon the operating mode, these topics will be covered in the associated mode explanation sections. 16.4.1 Counter All timer functions are based on the main 16-bit counter (TPMxCNTH:TPMxCNTL). This section discusses selection of the clock source, end-of-count overflow, up-counting vs. up/down counting, and manual counter reset. 16.4.1.1 Counter Clock Source The 2-bit field, CLKSB:CLKSA, in the timer status and control register (TPMxSC) selects one of three possible clock sources or OFF (which effectively disables the TPM). See Table 16-3. After any MCU reset, CLKSB:CLKSA=0:0 so no clock source is selected, and the TPM is in a very low power state. These control bits may be read or written at any time and disabling the timer (writing 00 to the CLKSB:CLKSA field) does not affect the values in the counter or other timer registers. Table16-7. TPM Clock Source Selection CLKSB:CLKSA TPM Clock Source to Prescaler Input 00 No clock selected (TPM counter disabled) 01 Bus rate clock 10 Fixed system clock 11 External source The bus rate clock is the main system bus clock for the MCU. This clock source requires no synchronization because it is the clock that is used for all internal MCU activities including operation of the CPU and buses. In MCUs that have no PLL or the PLL is not engaged, the fixed system clock source is the same as the bus-rate-clock source, and it does not go through a synchronizer. When a PLL is present and engaged, a synchronizer is required between the crystal divided-by two clock source and the timer counter so counter transitions will be properly aligned to bus-clock transitions. A synchronizer will be used at chip level to synchronize the crystal-related source clock to the bus clock. The external clock source may be connected to any TPM channel pin. This clock source always has to pass through a synchronizer to assure that counter transitions are properly aligned to bus clock transitions. The bus-rate clock drives the synchronizer; therefore, to meet Nyquist criteria even with jitter, the frequency of the external clock source must not be faster than the bus rate divided-by four. With ideal clocks the external clock can be as fast as bus clock divided by four. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 285

Timer/PWM Module (S08TPMV3) When the external clock source shares the TPM channel pin, this pin should not be used for other channel timing functions. For example, it would be ambiguous to configure channel 0 for input capture when the TPM channel 0 pin was also being used as the timer external clock source. (It is the user’s responsibility to avoid such settings.) The TPM channel could still be used in output compare mode for software timing functions (pin controls set not to affect the TPM channel pin). 16.4.1.2 Counter Overflow and Modulo Reset An interrupt flag and enable are associated with the 16-bit main counter. The flag (TOF) is a software-accessible indication that the timer counter has overflowed. The enable signal selects between software polling (TOIE=0) where no hardware interrupt is generated, or interrupt-driven operation (TOIE=1) where a static hardware interrupt is generated whenever the TOF flag is equal to one. The conditions causing TOF to become set depend on whether the TPM is configured for center-aligned PWM (CPWMS=1). In the simplest mode, there is no modulus limit and the TPM is not in CPWMS=1 mode. In this case, the 16-bit timer counter counts from 0x0000 through 0xFFFF and overflows to 0x0000 on the next counting clock. TOF becomes set at the transition from 0xFFFF to 0x0000. When a modulus limit is set, TOF becomes set at the transition from the value set in the modulus register to 0x0000. When the TPM is in center-aligned PWM mode (CPWMS=1), the TOF flag gets set as the counter changes direction at the end of the count value set in the modulus register (that is, at the transition from the value set in the modulus register to the next lower count value). This corresponds to the end of a PWM period (the 0x0000 count value corresponds to the center of a period). 16.4.1.3 Counting Modes The main timer counter has two counting modes. When center-aligned PWM is selected (CPWMS=1), the counter operates in up/down counting mode. Otherwise, the counter operates as a simple up counter. As an up counter, the timer counter counts from 0x0000 through its terminal count and then continues with 0x0000. The terminal count is 0xFFFF or a modulus value in TPMxMODH:TPMxMODL. When center-aligned PWM operation is specified, the counter counts up from 0x0000 through its terminal count and then down to 0x0000 where it changes back to up counting. Both 0x0000 and the terminal count value are normal length counts (one timer clock period long). In this mode, the timer overflow flag (TOF) becomes set at the end of the terminal-count period (as the count changes to the next lower count value). 16.4.1.4 Manual Counter Reset The main timer counter can be manually reset at any time by writing any value to either half of TPMxCNTH or TPMxCNTL. Resetting the counter in this manner also resets the coherency mechanism in case only half of the counter was read before resetting the count. 16.4.2 Channel Mode Selection Provided CPWMS=0, the MSnB and MSnA control bits in the channel n status and control registers determine the basic mode of operation for the corresponding channel. Choices include input capture, output compare, and edge-aligned PWM. MC9S08JM60 Series Data Sheet, Rev. 5 286 Freescale Semiconductor

Timer/PWM Module (S08TPMV3) 16.4.2.1 Input Capture Mode With the input-capture function, the TPM can capture the time at which an external event occurs. When an active edge occurs on the pin of an input-capture channel, the TPM latches the contents of the TPM counter into the channel-value registers (TPMxCnVH:TPMxCnVL). Rising edges, falling edges, or any edge may be chosen as the active edge that triggers an input capture. In input capture mode, the TPMxCnVH and TPMxCnVL registers are read only. When either half of the 16-bit capture register is read, the other half is latched into a buffer to support coherent 16-bit accesses in big-endian or little-endian order. The coherency sequence can be manually reset by writing to the channel status/control register (TPMxCnSC). An input capture event sets a flag bit (CHnF) which may optionally generate a CPU interrupt request. While in BDM, the input capture function works as configured by the user. When an external event occurs, the TPM latches the contents of the TPM counter (which is frozen because of the BDM mode) into the channel value registers and sets the flag bit. 16.4.2.2 Output Compare Mode With the output-compare function, the TPM can generate timed pulses with programmable position, polarity, duration, and frequency. When the counter reaches the value in the channel-value registers of an output-compare channel, the TPM can set, clear, or toggle the channel pin. In output compare mode, values are transferred to the corresponding timer channel registers only after both 8-bit halves of a 16-bit register have been written and according to the value of CLKSB:CLKSA bits, so: • If (CLKSB:CLKSA = 0:0), the registers are updated when the second byte is written • If (CLKSB:CLKSA not = 0:0), the registers are updated at the next change of the TPM counter (end of the prescaler counting) after the second byte is written. The coherency sequence can be manually reset by writing to the channel status/control register (TPMxCnSC). An output compare event sets a flag bit (CHnF) which may optionally generate a CPU-interrupt request. 16.4.2.3 Edge-Aligned PWM Mode This type of PWM output uses the normal up-counting mode of the timer counter (CPWMS=0) and can be used when other channels in the same TPM are configured for input capture or output compare functions. The period of this PWM signal is determined by the value of the modulus register (TPMxMODH:TPMxMODL) plus 1. The duty cycle is determined by the setting in the timer channel register (TPMxCnVH:TPMxCnVL). The polarity of this PWM signal is determined by the setting in the ELSnA control bit. 0% and 100% duty cycle cases are possible. The output compare value in the TPM channel registers determines the pulse width (duty cycle) of the PWM signal (Figure 16-15). The time between the modulus overflow and the output compare is the pulse width. If ELSnA=0, the counter overflow forces the PWM signal high, and the output compare forces the PWM signal low. If ELSnA=1, the counter overflow forces the PWM signal low, and the output compare forces the PWM signal high. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 287

Timer/PWM Module (S08TPMV3) OVERFLOW OVERFLOW OVERFLOW PERIOD PULSE WIDTH TPMxCHn OUTPUT OUTPUT OUTPUT COMPARE COMPARE COMPARE Figure16-15. PWM Period and Pulse Width (ELSnA=0) When the channel value register is set to 0x0000, the duty cycle is 0%. 100% duty cycle can be achieved by setting the timer-channel register (TPMxCnVH:TPMxCnVL) to a value greater than the modulus setting. This implies that the modulus setting must be less than 0xFFFF in order to get 100% duty cycle. Because the TPM may be used in an 8-bit MCU, the settings in the timer channel registers are buffered to ensure coherent 16-bit updates and to avoid unexpected PWM pulse widths. Writes to any of the registers TPMxCnVH and TPMxCnVL, actually write to buffer registers. In edge-aligned PWM mode, values are transferred to the corresponding timer-channel registers according to the value of CLKSB:CLKSA bits, so: • If (CLKSB:CLKSA = 0:0), the registers are updated when the second byte is written • If (CLKSB:CLKSA not = 0:0), the registers are updated after the both bytes were written, and the TPM counter changes from (TPMxMODH:TPMxMODL - 1) to (TPMxMODH:TPMxMODL). If the TPM counter is a free-running counter then the update is made when the TPM counter changes from 0xFFFE to 0xFFFF. 16.4.2.4 Center-Aligned PWM Mode This type of PWM output uses the up/down counting mode of the timer counter (CPWMS=1). The output compare value in TPMxCnVH:TPMxCnVL determines the pulse width (duty cycle) of the PWM signal while the period is determined by the value in TPMxMODH:TPMxMODL. TPMxMODH:TPMxMODL should be kept in the range of 0x0001 to 0x7FFF because values outside this range can produce ambiguous results. ELSnA will determine the polarity of the CPWM output. pulse width = 2 x (TPMxCnVH:TPMxCnVL) period = 2 x (TPMxMODH:TPMxMODL); TPMxMODH:TPMxMODL=0x0001-0x7FFF If the channel-value register TPMxCnVH:TPMxCnVL is zero or negative (bit 15 set), the duty cycle will be 0%. If TPMxCnVH:TPMxCnVL is a positive value (bit 15 clear) and is greater than the (non-zero) modulus setting, the duty cycle will be 100% because the duty cycle compare will never occur. This implies the usable range of periods set by the modulus register is 0x0001 through 0x7FFE (0x7FFF if you do not need to generate 100% duty cycle). This is not a significant limitation. The resulting period would be much longer than required for normal applications. TPMxMODH:TPMxMODL=0x0000 is a special case that should not be used with center-aligned PWM mode. When CPWMS=0, this case corresponds to the counter running free from 0x0000 through 0xFFFF, but when CPWMS=1 the counter needs a valid match to the modulus register somewhere other than at 0x0000 in order to change directions from up-counting to down-counting. MC9S08JM60 Series Data Sheet, Rev. 5 288 Freescale Semiconductor

Timer/PWM Module (S08TPMV3) The output compare value in the TPM channel registers (times 2) determines the pulse width (duty cycle) of the CPWM signal (Figure16-16). If ELSnA=0, a compare occurred while counting up forces the CPWM output signal low and a compare occurred while counting down forces the output high. The counter counts up until it reaches the modulo setting in TPMxMODH:TPMxMODL, then counts down until it reaches zero. This sets the period equal to two times TPMxMODH:TPMxMODL. OUTPUT COUNT= 0 OUTPUT COUNT= COMPARE COMPARE COUNT= TPMxMODH:TPMxMODL (COUNT DOWN) (COUNT UP) TPMxMODH:TPMxMODL TPMxCHn PULSE WIDTH 2 x TPMxCnVH:TPMxCnVL PERIOD 2 x TPMxMODH:TPMxMODL Figure16-16. CPWM Period and Pulse Width (ELSnA=0) Center-aligned PWM outputs typically produce less noise than edge-aligned PWMs because fewer I/O pin transitions are lined up at the same system clock edge. This type of PWM is also required for some types of motor drives. Input capture, output compare, and edge-aligned PWM functions do not make sense when the counter is operating in up/down counting mode so this implies that all active channels within a TPM must be used in CPWM mode when CPWMS=1. The TPM may be used in an 8-bit MCU. The settings in the timer channel registers are buffered to ensure coherent 16-bit updates and to avoid unexpected PWM pulse widths. Writes to any of the registers TPMxMODH, TPMxMODL, TPMxCnVH, and TPMxCnVL, actually write to buffer registers. In center-aligned PWM mode, the TPMxCnVH:L registers are updated with the value of their write buffer according to the value of CLKSB:CLKSA bits, so: • If (CLKSB:CLKSA = 0:0), the registers are updated when the second byte is written • If (CLKSB:CLKSA not = 0:0), the registers are updated after the both bytes were written, and the TPM counter changes from (TPMxMODH:TPMxMODL - 1) to (TPMxMODH:TPMxMODL). If the TPM counter is a free-running counter, the update is made when the TPM counter changes from 0xFFFE to 0xFFFF. When TPMxCNTH:TPMxCNTL=TPMxMODH:TPMxMODL, the TPM can optionally generate a TOF interrupt (at the end of this count). Writing to TPMxSC cancels any values written to TPMxMODH and/or TPMxMODL and resets the coherency mechanism for the modulo registers. Writing to TPMxCnSC cancels any values written to the channel value registers and resets the coherency mechanism for TPMxCnVH:TPMxCnVL. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 289

Timer/PWM Module (S08TPMV3) 16.5 Reset Overview 16.5.1 General The TPM is reset whenever any MCU reset occurs. 16.5.2 Description of Reset Operation Reset clears the TPMxSC register which disables clocks to the TPM and disables timer overflow interrupts (TOIE=0). CPWMS, MSnB, MSnA, ELSnB, and ELSnA are all cleared which configures all TPM channels for input-capture operation with the associated pins disconnected from I/O pin logic (so all MCU pins related to the TPM revert to general purpose I/O pins). 16.6 Interrupts 16.6.1 General The TPM generates an optional interrupt for the main counter overflow and an interrupt for each channel. The meaning of channel interrupts depends on each channel’s mode of operation. If the channel is configured for input capture, the interrupt flag is set each time the selected input capture edge is recognized. If the channel is configured for output compare or PWM modes, the interrupt flag is set each time the main timer counter matches the value in the 16-bit channel value register. All TPM interrupts are listed in Table16-8 which shows the interrupt name, the name of any local enable that can block the interrupt request from leaving the TPM and getting recognized by the separate interrupt processing logic. Table16-8. Interrupt Summary Local Interrupt Source Description Enable TOF TOIE Counter overflow Set each time the timer counter reaches its terminal count (at transition to next count value which is usually 0x0000) CHnF CHnIE Channel event An input capture or output compare event took place on channel n The TPM module will provide a high-true interrupt signal. Vectors and priorities are determined at chip integration time in the interrupt module so refer to the user’s guide for the interrupt module or to the chip’s complete documentation for details. 16.6.2 Description of Interrupt Operation For each interrupt source in the TPM, a flag bit is set upon recognition of the interrupt condition such as timer overflow, channel-input capture, or output-compare events. This flag may be read (polled) by software to determine that the action has occurred, or an associated enable bit (TOIE or CHnIE) can be set MC9S08JM60 Series Data Sheet, Rev. 5 290 Freescale Semiconductor

Timer/PWM Module (S08TPMV3) to enable hardware interrupt generation. While the interrupt enable bit is set, a static interrupt will generate whenever the associated interrupt flag equals one. The user’s software must perform a sequence of steps to clear the interrupt flag before returning from the interrupt-service routine. TPM interrupt flags are cleared by a two-step process including a read of the flag bit while it is set (1) followed by a write of zero (0) to the bit. If a new event is detected between these two steps, the sequence is reset and the interrupt flag remains set after the second step to avoid the possibility of missing the new event. 16.6.2.1 Timer Overflow Interrupt (TOF) Description The meaning and details of operation for TOF interrupts varies slightly depending upon the mode of operation of the TPM system (general purpose timing functions versus center-aligned PWM operation). The flag is cleared by the two step sequence described above. 16.6.2.1.1 Normal Case Normally TOF is set when the timer counter changes from 0xFFFF to 0x0000. When the TPM is not configured for center-aligned PWM (CPWMS=0), TOF gets set when the timer counter changes from the terminal count (the value in the modulo register) to 0x0000. This case corresponds to the normal meaning of counter overflow. 16.6.2.1.2 Center-Aligned PWM Case When CPWMS=1, TOF gets set when the timer counter changes direction from up-counting to down-counting at the end of the terminal count (the value in the modulo register). In this case the TOF corresponds to the end of a PWM period. 16.6.2.2 Channel Event Interrupt Description The meaning of channel interrupts depends on the channel’s current mode (input-capture, output-compare, edge-aligned PWM, or center-aligned PWM). 16.6.2.2.1 Input Capture Events When a channel is configured as an input capture channel, the ELSnB:ELSnA control bits select no edge (off), rising edges, falling edges or any edge as the edge which triggers an input capture event. When the selected edge is detected, the interrupt flag is set. The flag is cleared by the two-step sequence described in Section16.6.2, “Description of Interrupt Operation.” 16.6.2.2.2 Output Compare Events When a channel is configured as an output compare channel, the interrupt flag is set each time the main timer counter matches the 16-bit value in the channel value register. The flag is cleared by the two-step sequence described Section16.6.2, “Description of Interrupt Operation.” MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 291

Timer/PWM Module (S08TPMV3) 16.6.2.2.3 PWM End-of-Duty-Cycle Events For channels configured for PWM operation there are two possibilities. When the channel is configured for edge-aligned PWM, the channel flag gets set when the timer counter matches the channel value register which marks the end of the active duty cycle period. When the channel is configured for center-aligned PWM, the timer count matches the channel value register twice during each PWM cycle. In this CPWM case, the channel flag is set at the start and at the end of the active duty cycle period which are the times when the timer counter matches the channel value register. The flag is cleared by the two-step sequence described Section16.6.2, “Description of Interrupt Operation.” MC9S08JM60 Series Data Sheet, Rev. 5 292 Freescale Semiconductor

Chapter 17 Universal Serial Bus Device Controller (S08USBV1) 17.1 Introduction This chapter describes an universal serial bus device controller (S08USBV1) module that is based on the Universal Serial Bus Specification Rev 2.0. The USB bus is designed to replace existing bus interfaces such as RS-232, PS/2, and IEEE 1284 for PC peripherals. The S08USBV1 module provides a single-chip solution for full-speed (12 Mbps) USB device applications, and integrates the required transceiver with Serial Interface Engine (SIE), 3.3 V regualtor, Endpoint RAM and other control logics. 17.1.1 Clocking Requirements The S08USBV1 requires two clock sources, the 24 MHz bus clock and a 48 MHz reference clock. The 48 MHz clock is sourced directly from MCGOUT. To achieve the 48 MHz clock rate, the MCG must be configured properly for PLL engaged external (PEE) mode with an external crystal. For USB operation, examples of MCG configuration using PEE mode include: • 2 MHz crystal – RDIV = 000 and VDIV = 0110 • 4 MHz crystal – RDIV = 001 and VDIV = 0110 17.1.2 Current Consumption in USB Suspend In USB suspend mode, the USB device current consumption is limited to 500 μA. When the USB device goes into suspend mode, the firmware typically enters stop3 to meet the USB suspend requirements on current consumption. NOTE Enabling LVD increases current consumption in stop3. Consequently, when trying to satisfy USB suspend requirements, disabling LVD before entering stop3. 17.1.3 3.3 V Regulator If using an external 3.3 V regulator as an input to V (only when USBVREN = 0), the supply voltage, USB33 V , must not fall below the input voltage at the V pin. If using the internal 3.3 V regulator DD USB33 (USBVREN = 1), do not connect an external supply to the V pin. In this case, V must fall between USB33 DD 3.9 V and 5.5 V for the internal 3.3 V regulator to operate correctly. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 293

Chapter17 Universal Serial Bus Device Controller (S08USBV1) Table17-1. USBVREN Configuration USBVREN 3.3-V Regulator VDD Supply Voltage Range 0 External 3.3-V Regulator (as input to V pin) V ≤ V Supply Voltage USB33 USB33 DD Internal 3.3-V Regulator (no external supply connected to 3.9 V ≤ V Supply Voltage ≤ 5.5V 1 DD V pin) USB33 MC9S08JM60 Series Data Sheet, Rev. 5 294 Freescale Semiconductor

Chapter17 Universal Serial Bus Device Controller (S08USBV1) USBDP On Chip ICE AND USBDN HCS08 CORE DEBUG MODULE (DBG) A T 6 R PTA5– PTA0 O USB SIE P BKGD/MS FULL SPEED PTB7/ADP7 BDC CPU USB PTB6/ADP6 USB ENDPOINT TRANSCEIVER PTB5/KBIP5/ADP5 RAM T B PTB4/KBIP4/ADP4 SSPSS2CK2 POR PTB3/SS2/ADP3 RESET HCS08 SYSTEM CONTROL 8-/16-BIT SERIAL PERIPHERAL MOSI2 PTB2/SPSCK2/ADP2 INTERFACE MODULE (SPI2) PTB1/MOSI2/ADP1 MISO2 PTB0/MISO2/ADP0 RESETS AND INTERRUPTS MODES OF OPERATION PTC6 IRQ/TPMCLK POWER MANAGEMENT SERIAL COMMUNICATIONS RxD2 PTC5/RxD2 COP IRQ LVD INTERFACE MODULE (SCI2) TxD2 ORT C PPTTCC34/TxD2 P PTC2 SDA PTC1/SDA IIC MODULE (IIC) SCL PTC0/SCL VDDAD 12-CHANNEL, 12-BIT 8 PTD7 VSSAD ANALOG-TO-DIGITAL 4 PTD6 VREFL CONVERTER (ADC) PTD5 VREFH D PTD4/ADP11 T R PTD3/KBIP3/ADP10 O USER Flash (IN BYTES) P PTD2/KBIP2/ACMPO ACMP– MC9S08JM60 = 60,912 PTD1/ADP9/ACMP– MC9S08JM32 = 32,768 ANALOG COMPARATOR ACMP+ PTD0/ADP8/ACMP+ (ACMP) ACMPO SS1 PTE7/SS1 USER RAM (IN BYTES) SPSCK1 8-/16-BIT SERIAL PERIPHERAL PTE6/SPSCK1 MMCC99SS0088JJMM6302 == 42009468 INTERFACE MODULE (SPI1) MOSI1 PTE5/MOSI1 MISO1 PTE4/MISO1 TPMCLK E MULTI-PURPOSE CLOCK 6-CHMAONDNUELLE T (IMTPEMR1/P)WM TTPPMM11CCHH10 PORT PTE3/TPM1CH1 GENERATOR (MCG) PTE2/TPM1CH0 TPM1CHx4 RxD1 SERIAL COMMUNICATIONS PTE1/RxD1 VSSOSC LOW-POWER OSCILLATOR TxD1 PTE0/TxD1 INTERFACE MODULE (SCI1) PTF7 VDD SYSTEM TPMCLK PTF6 VSS RVEOGLUTLAAGTEO R 2-CHMAONDNUELLE T (IMTPEMR2/P)WM TTPPMM22CCHH10 T F PPTTFF54//TTPPMM22CCHH10 OR PTF3/TPM1CH5 KBIPx P PTF2/TPM1CH4 VUSB33 USB 3.3 V VOLTAGE REGULATOR 8-BIT KEYBOARD 4 PTF1/TPM1CH3 INTERRUPT MODULE (KBI) KBIPx 4 PTF0/TPM1CH2 REAL-TIME COUNTER (RTC) EXTAL PTG5/EXTAL XTAL NOTES: G PTG4/XTAL 1. Port pins are software configurable with pullup device if input port. RT PTG3/KBIP7 O PTG2/KBIP6 2. Pin contains software configurable pullup/pull-down device ifpullup IRQ is enabled P PTG1/KBIP1 (IRQPE=1). Pull-down is enabled if rising edge detect is selected (IRQEDG=1) PTG0/KBIP0 3. IRQ does not have a clamp diode to V . IRQ must not be driven above V . DD DD 4. Pin contains integrated pullup device. 5. When pin functions as KBI (KBIPEn = 1) and associated pin is configured to enable the pullup device, KBEDGn can be used to reconfigure the pullup as a pull-down device. Figure17-1. MC9S08JM60 Series Block Diagram Highlighting USB Blocks and Pins MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 295

Universal Serial Bus Device Controller (S08USBV1) 17.1.4 Features Features of the USB module include: • USB 2.0 compliant — 12 Mbps full-speed (FS) data rate — USB data control logic: – Packet identification and decoding/generation – CRC generation and checking – NRZI (non-return-to-zero inverted) encoding/decoding – Bit-stuffing – Sync detection – End-of-packet detection • Seven USB endpoints — Bidirectional endpoint 0 — Six unidirectional data endpoints configurable as interrupt, bulk, or isochronous — Endpoints 5 and 6 support double-buffering • USB RAM — 256 bytes of buffer RAM shared between system and USB module — RAM may be allocated as buffers for USB controller or extra system RAM resource • USB reset options — USB module reset generated by MCU — Bus reset generated by the host, which triggers a CPU interrupt • Suspend and resume operations with remote wakeup support • Transceiver features — Converts USB differential voltages to digital logic signal levels • On-chip USB pullup resistor • On-chip 3.3-V regulator 17.1.5 Modes of Operation Table17-2. Operating Modes Mode Description Stop1 USB module is not functional. Before entering stop1, the internal USB voltage regulator and USB transceiver enter shutdown mode; therefore, the USB voltage regulator and USB transceiver must be disabled by firmware. Stop2 USB module is not functional. Before entering stop2, the internal USB voltage regulator and USB transceiver enter shutdown mode; therefore, the USB voltage regulator and USB transceiver must be disabled by firmware. MC9S08JM60 Series Data Sheet, Rev. 5 296 Freescale Semiconductor

Universal Serial Bus Device Controller (S08USBV1) Table17-2. Operating Modes (continued) Mode Description Stop3 The USB module is optionally available in stop3. A reduced current consumption mode may be required for USB suspend mode per USB Specification Rev. 2.0, and stop3 mode is useful for achieving lower current consumption for the MCU and hence the overall USB device. Before entering stop3 via firmware, the user must ensure that the device settings are configured for stop3 to achieve USB suspend current consumption targets. The USB module is notified about entering suspend mode when the SLEEPF flag is set; this occurs after the USB bus is idle for 3 ms. The device USB suspend mode current consumption level requirements are defined by the USB Specification Rev. 2.0 (500 μA for low-power and 2.5 mA for high-power with remote-wakeup enabled). If USBRESMEN in USBCTL0 is set, and a K-state (resume signaling) is detected on the USB bus, the LPRESF bit in USBCTL0 will be set. This triggers an asynchronous interrupt that will wakeup the MCU from stop3 mode and enable clocks to the USB module. The USBRESMEN bit must then be cleared immediately after stop3 recovery to clear the LPRESF flag bit. Wait USB module is operational. 17.1.6 Block Diagram Figure 17-2 is a block diagram of the USB module. 48-MHz Reference Clock 24-MHz Clock (bus clk) USB CONTROLLER Serial Interface Engine Enable (SIE) USBDP Pullup BVCI TX IRQ USB RAM Target Logic USBDP et XCVR k 256 bytes as USBDN G e Protocol and Rate Blu Match Local Bus nterrupt Controller Peripheral Bus Sky RAMArbitration BufferManager InBitViaCtoIr LRogXic VREG VUSB33 o I T Figure17-2. USB Module Block Diagram MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 297

Universal Serial Bus Device Controller (S08USBV1) 17.2 External Signal Description The USB module requires both data and power pins. Table 17-3 describes each of the USB external pin Table17-3. USB External Pins Name Port Direction Function Reset State High Positive USB differential signal USBDP I/O Differential USB signaling. impedance High Negative USB differential signal USBDN I/O Differential USB signaling. impedance 3.3 V USB voltage regulator output USB voltage regulator power pin V Power or 3.3 V USB transceiver/resistor — USB33 supply input. 17.2.1 USBDP USBDP is the positive USB differential signal. In a USB peripheral application, connect an external 33 Ω ±1% resistor in series with this signal in order to meet the USB Specification Rev. 2.0 impedance requirement. 17.2.2 USBDN USBDN is the negative USB differential signal. In a USB peripheral application, connect an external 33 Ω ±1% resistor in series with this signal in order to meet the USB Specification, Rev. 2.0 impedance requirement. 17.2.3 V USB33 V is connected to the on-chip 3.3-V voltage regulator (VREG). V maintains an output voltage USB33 USB33 of 3.3V and can only source enough current for USB internal transceiver (XCVR) and USB pullup resistor. If the VREG is disabled by software, the application must input an external 3.3 V power supply to the USB module via V . USB33 17.3 Register Definition This section describes the memory map and control/status registers for the USB module. MC9S08JM60 Series Data Sheet, Rev. 5 298 Freescale Semiconductor

Universal Serial Bus Device Controller (S08USBV1) 17.3.1 USB Control Register 0 (USBCTL0) 7 6 5 4 3 2 1 0 R 0 LPRESF 0 0 USBRES USBPU USBVREN USBPHYEN W USBRESET MEN Reset 0 0 0 0 0 0 0 0 = Unimplemented or Reserved Figure17-3. USB Transceiver and Regulator Control Register 0 (USBCTL0) Table17-4. USBCTL0 Field Descriptions Field Description 7 USB Reset — This bit generates a hard reset of the USB module, USBPHYEN and USBVREGEN bits will also USBRESET be cleared. (need remember to restart USB Transceiver and USB voltage regulator). When set to 1, this bit automatically clears when the reset occurs. 0 USB module normal operation 1 Returns the USB module to its reset state 6 Pull Up Source — This bit determines the source of the pullup resistor on the USBDP line. USBPU 0 Internal USBDP pullup resistor is disabled; The application can use an external pullup resistor 1 Internal USBDP pullup resistor is enabled 5 USB Low-Power Resume Event Enable — This bit, when set, enables the USB module to send an USBRESMEN asynchronous wakeup interrupt to the MCU upon detection that the LPRESF bit has been set, indicating a K-state on the USB bus. This bit must be set before entering low-power stop3 mode only after SLEEPF=1 (USB is entering suspend mode). It must be cleared immediately after stop3 recovery in order to clear the Low-Power Resume Flag. 0 USB asynchronous wakeup from suspend mode disabled 1 USB asynchronous wakeup from suspend mode enabled 4 Low-Power Resume Flag — This bit becomes set in USB suspend mode if USBRESMEN=1 and a K-state is LPRESF detected on the USB bus, indicating resume signaling while the device is in a low-power stop3 mode. This flag bit will trigger an asynchronous interrupt, which will wake the device from stop3. Firmware must then clear the USBRESMEN bit in order to clear the LPRESF bit. 0 No K-state detected on the USB bus while the device is in stop3 and the USB is suspended. 1 K-state detected on the USB bus when USBRESMEN=1, the device is in stop3, and the USB is suspended. 2 USB Voltage Regulator Enable — This bit enables the on-chip 3.3V USB voltage regulator. USBVREN 0 On-chip USB voltage regulator is disabled (OFF MODE) 1 On-chip USB voltage regulator is enabled for active or standby mode 0 USB Transceiver Enable — When the USB Transceiver (XCVR) is disabled, USBDP and USBDN are hi-Z. It is USBPHYEN recommended that the XCVR be enabled before setting the USBEN bit in the CTL register. The firmware must ensure that the XCVR remains enabled when entering USB SUSPEND mode. 0 On-chip XCVR is disabled 1 On-chip XCVR is enabled 17.3.2 Peripheral ID Register (PERID) The PERID reads back the value of 0x04. This value is defined for the USB module peripheral. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 299

Universal Serial Bus Device Controller (S08USBV1) 7 6 5 4 3 2 1 0 R 0 0 ID5 ID4 ID3 ID2 ID1 ID0 W Reset 0 0 0 0 0 1 0 0 = Unimplemented or Reserved Figure17-4. Peripheral ID Register (PERID) Table17-5. PERID Field Descriptions Field Description 5:0 Peripheral Configuration Number —This number is set to 0x04 and indicates that the peripheral is the ID[5:0] full-speed USB module. 17.3.3 Peripheral ID Complement Register (IDCOMP) The IDCOMP reads back the complement of the peripheral ID register. For the USB module peripheral this will be 0xFB. 7 6 5 4 3 2 1 0 R 1 1 NID5 NID4 NID3 NID2 NID1 NID0 W Reset 1 1 1 1 1 0 1 1 = Unimplemented or Reserved Figure17-5. Peripheral ID Complement Register (IDCOMP) Table17-6. IDCOMP Field Descriptions Field Description 5:0 Compliment ID Number — One’s complement version of ID[5:0]. NID[5:0] 17.3.4 Peripheral Revision Register (REV) The REV reads back the value of the USB peripheral revision. 7 6 5 4 3 2 1 0 R REV7 REV6 REV5 REV4 REV3 REV2 REV1 REV0 W Reset 0 0 0 0 0 0 0 0 = Unimplemented or Reserved Figure17-6. Peripheral Revision Register (REV) MC9S08JM60 Series Data Sheet, Rev. 5 300 Freescale Semiconductor

Universal Serial Bus Device Controller (S08USBV1) Table17-7. REV Field Descriptions Field Description 8–0 Revision — Revision number of the USB module. REV[7:0] 17.3.5 Interrupt Status Register (INTSTAT) The INTSTAT contains bits for each of the interrupt source within the USB module. Each of these bits is qualified with its respective interrupt enable bits (see the interrupt enable register). All bits of the register are logically OR'ed together to form a single interrupt source for the microcontroller. Once an interrupt bit has been set, it may only be cleared by writing a 1 to the respective interrupt bit. This register will contain the value of 0x00 after a reset. 7 6 5 4 3 2 1 0 R 0 STALLF RESUMEF SLEEPF TOKDNEF SOFTOKF ERRORF USBRSTF W Reset 0 0 0 0 0 0 0 0 = Unimplemented or Reserved Figure17-8. Interrupt Status Register (INTSTAT) Table17-9. INTSTAT Field Descriptions Field Description 7 Stall Flag — The stall interrupt is used in device mode. In device mode the stall flag is asserted when a STALL STALLF handshake is sent by the serial interface engine (SIE). 0 A STALL handshake has not been sent 1 A STALL handshake has been sent 5 Resume Flag — This bit is set 2.5 μs after clocks to the USB module have restarted following resume signaling. RESUMEF It can be used to indicate remote wakeup signaling on the USB bus. This interrupt is enabled only when the USB module is about to enter suspend mode (usually when SLEEPF interrupt detected). 0 No RESUME observed 1 RESUME detected (K-state is observed on the USBDP/USBDN signals for 2.5 μs) 4 Sleep Flag — This bit is set if the USB module has detected a constant idle on the USB bus for 3 ms, indicating SLEEPF that the USB module will go into suspend mode. The sleep timer is reset by activity on the USB bus. 0 No constant idle state of 3 ms has been detected on the USB bus 1 A constant idle state of 3 ms has been detected on the USB bus 3 Token Complete Flag — This bit is set when the current transaction is completed. The firmware must TOKDNEF immediately read the STAT register to determine the endpoint and BD information. Clearing this bit (by setting it to 1) causes the STAT register to be cleared or the STAT FIFO holding register to be loaded into the STAT register. 0 No tokens being processed are complete 1 Current token being processed is complete 2 SOF Token Flag — This bit is set if the USB module has received a start of frame (SOF) token. SOFTOKF 0 The USB module has not received an SOF token 1 The USB module has received an SOF token MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 301

Universal Serial Bus Device Controller (S08USBV1) Table17-9. INTSTAT Field Descriptions (continued) Field Description 1 Error Flag — This bit is set when any of the error conditions within the ERRSTAT register has occurred. The ERRORF firmware must then read the ERRSTAT register to determine the source of the error. 0 No error conditions within the ERRSTAT register have been detected 1 Error conditions within the ERRSTAT register have been detected 0 USB Reset Flag —This bit is set when the USB module has decoded a valid USB reset. When asserted, this bit USBRSTF will inform the MCU to automatically write 0x00 to the address register and to enable endpoint 0. USBRSTF is set once a USB reset has been detected for 2.5 μs. It will not be asserted again until the USB reset condition has been removed, and then reasserted. 0 No USB reset observed 1 USB reset detected 17.3.6 Interrupt Enable Register (INTENB) The INTENB contains enabling bits for each of the interrupt sources within the USB module. Setting any of these bits will enable the respective interrupt source in the INTSTAT register. This register will contain the value of 0x00 after a reset, i.e. all interrupts disabled. 7 6 5 4 3 2 1 0 R 0 STALL RESUME SLEEP TOKDNE SOFTOK ERROR USBRST W Reset 0 0 0 0 0 0 0 0 Figure17-9. Interrupt Enable Register (INTENB) Table17-10. INTENB Field Descriptions Field Description 7 STALL Interrupt Enable — Setting this bit will enable STALL interrupts. STALL 0 Interrupt disabled 1 Interrupt enabled 5 RESUME Interrupt Enable — Setting this bit will enable RESUME interrupts. RESUME 0 Interrupt disabled 1 Interrupt enabled 4 SLEEP Interrupt Enable — Setting this bit will enable SLEEP interrupts. SLEEP 0 Interrupt disabled 1 Interrupt enabled 3 TOKDNE Interrupt Enable — Setting this bit will enable TOKDNE interrupts. TOKDNE 0 Interrupt disabled 1 Interrupt enabled 2 SOFTOK Interrupt Enable — Setting this bit will enable SOFTOK interrupts. SOFTOK 0 Interrupt disabled 1 Interrupt enabled MC9S08JM60 Series Data Sheet, Rev. 5 302 Freescale Semiconductor

Universal Serial Bus Device Controller (S08USBV1) Table17-10. INTENB Field Descriptions (continued) Field Description 1 ERROR Interrupt Enable — Setting this bit will enable ERROR interrupts. ERROR 0 Interrupt disabled 1 Interrupt enabled 0 USBRST Interrupt Enable — Setting this bit will enable USBRST interrupts. USBRST 0 Interrupt disabled 1 Interrupt enabled 17.3.7 Error Interrupt Status Register (ERRSTAT) The ERRSTAT contains bits for each of the error sources within the USB module. Each of these bits corresponds to its respective error enable bit (See Section17.3.8, “Error Interrupt Enable Register (ERRENB)”.) The result is OR'ed together and sent to the ERROR bit of the INTSTAT register. Once an interrupt bit has been set, it may only be cleared by writing a 1 to the corresponding flag bit. Each bit is set as soon as the error condition is detected. Thus, the interrupt will typically not correspond with the end of a token being processed. This register will contain the value of 0x00 after reset. 7 6 5 4 3 2 1 0 R BTSERRF Reserved BUFERRF BTOERRF DFN8F CRC16F CRC5F PIDERRF W Reset 0 0 0 0 0 0 0 0 Figure17-10. Error Interrupt Status Register (ERRSTAT) Table17-11. ERRSTAT Field Descriptions Field Description 7 Bit Stuff Error Flag — A bit stuff error has been detected. If set, the corresponding packet will be rejected due BTSERRF to a bit stuff error. 0 No bit stuff error detected 1 Bit stuff error flag set 5 Buffer Error Flag — This bit is set if the USB module has requested a memory access to read a new BD but BUFERRF has not been given the bus before the USB module needs to receive or transmit data. If processing a TX (IN endpoint) transfer, this would cause a transmit data underflow condition. Or if processing an Rx (OUT endpoint) transfer, this would cause a receive data overflow condition. This bit is also set if a data packet to or from the host is larger than the buffer size that is allocated in the BD. In this case the data packet is truncated as it is put into buffer memory. 0 No buffer error detected 1 A buffer error has occurred 4 Bus Turnaround Error Timeout Flag — This bit is set if a bus turnaround timeout error has occurred. The USB BTOERRF module uses a bus turnaround timer to keep track of the amount of time elapsed between the token and data phases of a SETUP or OUT TOKEN or the data and handshake phases of an IN TOKEN. If more than 16-bit times are counted from the previous EOP before a transition from IDLE, a bus turnaround timeout error will occur. 0 No bus turnaround timeout error has been detected 1 A bus turnaround timeout error has occurred MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 303

Universal Serial Bus Device Controller (S08USBV1) Table17-11. ERRSTAT Field Descriptions (continued) Field Description 3 Data Field Error Flag — The data field received was not an interval of 8 bits. The USB Specification specifies DFN8F that the data field must be an integer number of bytes. If the data field was not an integer number of bytes, this bit will be set. 0 The data field was an integer number of bytes 1 The data field was not an integer number of bytes 2 CRC16 Error Flag — The CRC16 failed. If set, the data packet was rejected due to a CRC16 error. CRC16F 0 No CRC16 error detected 1 CRC16 error detected 1 CRC5 Error Flag — This bit will detect a CRC5 error in the token packets generated by the host. If set, the CRC5F token packet was rejected due to a CRC5 error. 0 No CRC5 error detected 1 CRC5 error detected, and the token packet was rejected. 0 PID Error Flag — The PID check failed. PIDERRF 0 No PID check error detected 1 PID check error detected 17.3.8 Error Interrupt Enable Register (ERRENB) 7 6 5 4 3 2 1 0 R 0 BTSERR BUFERR BTOERR DFN8 CRC16 CRC5 PIDERR W Reset 0 0 0 0 0 0 0 0 Figure17-11. Error Interrupt Enable Register (ERRENB) Table17-12. ERRSTAT Field Descriptions Field Description 7 BTSERR Interrupt Enable — Setting this bit will enable BTSERR interrupts. BTSERR 0 Interrupt disabled 1 Interrupt enabled 5 BUFERR Interrupt Enable — Setting this bit will enable BUFERR interrupts. BUFERR 0 Interrupt disabled 1 Interrupt enabled 4 BTOERR Interrupt Enable — Setting this bit will enable BTOERR interrupts. BTOERR 0 Interrupt disabled 1 Interrupt enabled 3 DFN8 Interrupt Enable — Setting this bit will enable DFN8 interrupts. DFN8 0 Interrupt disabled 1 Interrupt enabled 2 CRC16 Interrupt Enable — Setting this bit will enable CRC16 interrupts. CRC16 0 Interrupt disabled 1 Interrupt enabled MC9S08JM60 Series Data Sheet, Rev. 5 304 Freescale Semiconductor

Universal Serial Bus Device Controller (S08USBV1) Table17-12. ERRSTAT Field Descriptions (continued) Field Description 1 CRC5 Interrupt Enable — Setting this bit will enable CRC5 interrupts. CRC5 0 Interrupt disabled 1 Interrupt enabled 0 PIDERR Interrupt Enable — Setting this bit will enable PIDERR interrupts. PIDERR 0 Interrupt disabled 1 Interrupt enabled 17.3.9 Status Register (STAT) The STAT reports the transaction status within the USB module. When the MCU receives a TOKDNE interrupt, the STAT is read to determine the status of the previous endpoint communication. The data in the status register is valid only when the TOKDNEF interrupt flag is asserted. The STAT register is actually a read window into a status FIFO maintained by the USB module. When the USB module uses a BD, it updates the status register. If another USB transaction is performed before the TOKDNE interrupt is serviced, the USB module will store the status of the next transaction in the STAT FIFO. Thus, the STAT register is actually a four byte FIFO which allows the microcontroller to process one transaction while the serial interface engine (SIE) is processing the next. Clearing the TOKDNEF bit in the INTSTAT register causes the SIE to update the STAT register with the contents of the next STAT value. If the next data in the STAT FIFO holding register is valid, the SIE will immediately reassert the TOKDNE interrupt. 7 6 5 4 3 2 1 0 R ENDP[3:0] IN ODD 0 0 W Reset 0 0 0 0 0 0 0 0 = Unimplemented or Reserved Figure17-12. Status Register (STAT) Table17-13. STAT Field Descriptions Field Description 7–4 Endpoint Number — These four bits encode the endpoint address that received or transmitted the previous ENDP[3:0] token. This allows the microcontroller to determine which BDT entry was updated by the last USB transaction. 0000 Endpoint 0 0001 Endpoint 1 0010 Endpoint 2 0011 Endpoint 3 0100 Endpoint 4 0101 Endpoint 5 0110 Endpoint 6 MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 305

Universal Serial Bus Device Controller (S08USBV1) Table17-13. STAT Field Descriptions (continued) Field Description 3 In/Out Transaction — This bit indicates whether the last BDT updated was for a transmit (IN) transfer or a IN receive (OUT) data transfer. 0 Last transaction was a receive (OUT) data transfer 1 Last BDT updated was for transmit (IN) transfer 2 Odd/Even Transaction —This bit indicates whether the last buffer descriptor updated was in the odd bank of ODD the BDT or the even bank of the BDT, See earlier section for more information on BDT address generation. 0 Last buffer descriptor updated was in the EVEN bank 1 Last buffer descriptor updated was in the ODD bank 17.3.10 Control Register (CTL) The CTL provides various control and configuration information for the USB module. 7 6 5 4 3 2 1 0 R TSUSPEND CRESUME ODDRST USBEN W Reset 0 0 0 0 0 0 0 0 Figure17-13. Control Register (CTL) Table17-14. CTL Field Descriptions Field Description 5 Transaction Suspend — This bit is set by the serial interface engine (SIE) when a setup token is received, TSUSPEND allowing software to dequeue any pending packet transactions in the BDT before resuming token processing. The TSUSPEND bit informs the processor that the SIE has disabled packet transmission and reception. Clearing this bit allows the SIE to continue token processing. 0 Allows the SIE to continue token processing 1 Set by the SIE when a setup token is received; SIE has disabled packet transmission and reception. 2 Resume Signaling — Setting this bit will allow the USB module to execute resume signaling. This will allow CRESUME the USB module to perform remote wakeup. Software must set CRESUME to 1 for the amount of time required by the USB Specification Rev. 2.0 and then clear it to 0. 0 Do not execute remote wakeup 1 Execute resume signaling - remote wakeup 1 Odd Reset — Setting this bit will reset all the buffer descriptor ODD ping-pong bits to 0 which will then specify ODDRST the EVEN descriptor bank. This bit is used with double-buffered endpoints 5 and 6. This bit has no effect on endpoints 0 through 4. 0 Do not reset 1 Reset all the buffer descriptor ODD ping/pong bits to 0 which will then specify the EVEN descriptor bank 0 USB Enable Setting this bit will enable the USB module to operate. Setting this bit causes the SIE to reset USBEN all of its ODD bits to the BDTs. Thus, setting this bit will reset much of the logic in the SIE. 0 Disable the USB module 1 Enable the USB module for operation, will not affect Transceiver and VREG. MC9S08JM60 Series Data Sheet, Rev. 5 306 Freescale Semiconductor

Universal Serial Bus Device Controller (S08USBV1) 17.3.11 Address Register (ADDR) The ADDR register contains the unique 7-bit address the device will be recognized as through USB. The register is reset to 0x00 after the reset input has gone active or the USB module has decoded USB reset signaling. That will initialize the address register to decode address 0x00 as required by the USB specification. Firmware will change the value when it processes a SET_ADDRESS request. 7 6 5 4 3 2 1 0 R 0 ADDR6 ADDR5 ADDR4 ADDR3 ADDR2 ADDR1 ADDR0 W Reset 0 0 0 0 0 0 0 0 Figure17-14. Address Register (ADDR) Table17-15. ADDR Field Descriptions Field Description 6–0 USB Address — This 7-bit value defines the USB address that the USB module will decode ADDR[6:0] 17.3.12 Frame Number Register (FRMNUML, FRMNUMH) The frame number registers contains the 11-bit frame number. The frame number registers require two 8-bit registers to implement. The low order byte is contained in FRMNUML, and the high order byte is contained in FRMNUMH. These registers are updated with the current frame number whenever a SOF TOKEN is received. 7 6 5 4 3 2 1 0 R FRM7 FRM6 FRM5 FRM4 FRM3 FRM2 FRM1 FRM0 W Reset 0 0 0 0 0 0 0 0 = Unimplemented or Reserved Figure17-15. Frame Number Register Low (FRMNUML) Table17-16. FRMNUML Field Descriptions Field Description 7–0 Frame Number — These bits represent the low order bits of the 11 bit frame number. FRM[7:0] MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 307

Universal Serial Bus Device Controller (S08USBV1) 7 6 5 4 3 2 1 0 R 0 0 0 0 0 FRM10 FRM9 FRM8 W Reset 0 0 0 0 0 0 0 0 = Unimplemented or Reserved Figure17-16. Frame Number Register High (FRMNUMH) Table17-17. FRMNUMH Field Descriptions Field Description 2–0 Frame Number — These bits represent the high order bits of the 11-bit frame number. FRM[10:8] 17.3.13 Endpoint Control Register (EPCTLn, n=0-6) The endpoint control registers contains the endpoint control bits (EPCTLDIS, EPRXEN, EPTXEN, and EPHSHK) for each endpoint available within the USB module for a decoded address. These four bits define all of the control necessary for any one endpoint. The formats for these registers are shown in the tables below. Endpoint 0 (ENDP0) is associated with control pipe 0 which is required by the USB for all functions. Therefore, after a USBRST interrupt has been received, the microcontroller must set EPCTL0 to contain 0x0D. 7 6 5 4 3 2 1 0 R 0 0 0 EPCTLDIS EPRXEN EPTXEN EPSTALL EPHSHK W Reset 0 0 0 0 0 0 0 0 (EP0-6) = Unimplemented or Reserved Figure17-17. Endpoint Control Register (EPCTLn) Table17-18. EPCTLn Field Descriptions Field Description 4 Endpoint Control — This bit defines if an endpoint is enabled and the direction of the endpoint. The EPCTLDIS endpoint enable/direction control is defined in Table17-19. 3 Endpoint Rx Enable — This bit defines if an endpoint is enabled for OUT transfers. The endpoint EPRXEN enable/direction control is defined in Table17-19. 2 Endpoint Tx Enable — This bit defines if an endpoint is enabled for IN transfers. The endpoint EPTXEN enable/direction control is defined in Table17-19. MC9S08JM60 Series Data Sheet, Rev. 5 308 Freescale Semiconductor

Universal Serial Bus Device Controller (S08USBV1) Table17-18. EPCTLn Field Descriptions (continued) Field Description 1 Endpoint Stall — When set, this bit indicates that the endpoint is stalled. This bit has priority over all other EPSTALL control bits in the endpoint control register, but is only valid if EPTXEN=1 or EPRXEN=1. Any access to this endpoint will cause the USB module to return a STALL handshake. Once an endpoint is stalled it requires intervention from the host controller. 0 Endpoint n is not stalled 1 Endpoint n is stalled 0 Endpoint Handshake — This bit determines if the endpoint will perform handshaking during a transaction EPHSHK to the endpoint. This bit will generally be set unless the endpoint is isochronous. 0 No handshaking performed during a transaction to this endpoint (usually for isochronous endpoints) 1 Handshaking performed during a transaction to this endpoint Table17-19. Endpoint Enable/Direction Control Bit Name Endpoint Enable/Direction Control 4 3 2 EPCTLDIS EPRXEN EPTXEN X 0 0 Disable endpoint X 0 1 Enable endpoint for IN(TX) transfers only X 1 0 Enable endpoint for OUT(RX) transfers only 0 1 1 Enable endpoint for IN, OUT and SETUP transfers. 1 1 1 RESERVED 17.4 Functional Description This section describes the functional behavior of the USB module. It documents data packet processing for endpoint 0 and data endpoints, USB suspend and resume states, SOF token processing, reset conditions and interrupts. 17.4.1 Block Descriptions Figure 17-2 is the block diagram. The module’s sub-blocks and external signals are described in the following sections. The module involves several major blocks — USB transceiver (XCVR), USB serial interface engine (SIE), a 3.3 V regulator (VREG), endpoint buffer manager, shared RAM arbitration, USB RAM and the SkyBlue gasket. 17.4.1.1 USB Serial Interface Engine (SIE) The SIE is composed of two major functions: TX Logic and RX Logic. These major functions are described below in more detail. The TX and RX logic are connected by a USB protocol engine which manages packet flow to and from the USB module. The SIE is connected to the rest of the system via MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 309

Universal Serial Bus Device Controller (S08USBV1) internal basic virtual component interface (BVCI) compliant target and initiator buses. The BVCI target interface is used to configure the USB SIE and to provide status and interrupts to CPU. The BVCI initiator interface provides the integrated DMA controller access to the buffer descriptor table (BDT), and transfers USB data to or from USB RAM memory. 17.4.1.1.1 Serial Interface Engine (SIE) Transmitter Logic The SIE transmitter logic has two primary functions. The first is to format the USB data packets that have been stored in the endpoint buffers. The second is to transmit data packets via the USB transceiver. All of the necessary USB data formatting is performed by the SIE transmitter logic, including: • NRZI encoding • bit-stuffing • CRC computation • addition of the SYNC field • addition of the End-of-packet (EOP) The CPU typically places data in the endpoint buffers as part of the application. When the buffer is configured as an IN buffer and the USB host requests a packet, the SIE responds with a properly formatted data packet. The transmitter logic is also used to generate responses to packets received from the USB host. When a properly formatted packet is received from the USB host, the transmitter logic responds with the appropriate ACK, NAK or STALL handshake. When the SIE transmitter logic is transmitting data from the buffer space for a particular endpoint, CPU access to that endpoint buffer space is not recommended. 17.4.1.1.2 Serial Interface Engine (SIE) Receiver Logic The SIE receiver logic receives USB data and stores USB packets in USB RAM for processing by the CPU and the application software. Serial data from the transceiver is converted to a byte-wide parallel data stream, checked for proper packet framing, and stored in the USB RAM memory. Received bitstream processing includes the following operations: • decodes an NRZI USB serial data stream • Sync detection • Bit-stuff removal (and error detection) • End-of-packet (EOP) detection • CRC validation • PID check • other USB protocol layer checks. The SIE receiver logic provides error detection including: • Bad CRC • Timeout detection for EOP MC9S08JM60 Series Data Sheet, Rev. 5 310 Freescale Semiconductor

Universal Serial Bus Device Controller (S08USBV1) • Bit stuffing violation If a properly formatted packet is received, the receiver logic initiates a handshake response to the host. If the packet is not decoded correctly due to bit stuff violation, CRC error or other packet level problem, the receiver ignores it. The USB host will eventually time-out waiting for a response, and retransmit the packet. When the SIE receiver logic is receiving data in the buffer space for a particular endpoint, CPU access to that buffer space is not recommended. 17.4.1.2 MCU/Memory Interfaces 17.4.1.2.1 SkyBlue Gasket The SkyBlue gasket connects the USB module to the SoC internal peripheral bus. The gasket maps accesses to the endpoint buffer descriptors or the endpoint buffers into the shared RAM block, and it also maps accesses to the peripherals register set into the serial interface engine (SIE) register space. The SkyBlue gasket interface includes registers to control the USB transceiver and voltage regulator. 17.4.1.2.2 Endpoint Buffer Manager Each endpoint supported by the USB device transmits data to and from buffers stored in the shared buffer memory. The serial interface engine (SIE) uses a table of descriptors, the Buffer Descriptor Table (BDT), which is also stored in the USB RAM to describe the characteristics of each endpoint. The endpoint buffer manager is responsible for mapping requests to access endpoint buffer descriptors into physical addresses within the USB RAM block. 17.4.1.2.3 RAM Arbitration The arbitration block allows access to the USB RAM block from the SkyBlue gasket block and from the SIE. 17.4.1.3 USB RAM The USB module includes 256 bytes of high speed RAM, accessible by the USB serial interface engine (SIE) and the CPU. The USB RAM runs at twice the speed of the bus clock to allow interleaved non-blocked access by the CPU and SIE. The USB RAM is used for storage of the buffer descriptor table (BDT) and endpoint buffers. USB RAM that is not allocated for the BDT and endpoint buffers can be used as system memory. If the USB module is not enabled, then the entire USB RAM may be used as unsecured system memory. 17.4.1.4 USB Transceiver (XCVR) The USB transceiver is electrically compliant to the Universal Serial Bus Specification 2.0. This block provides the necessary 2-wire differential NRZI signaling for USB communication. The transceiver is on-chip to provide a cost effective single chip USB peripheral solution. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 311

Universal Serial Bus Device Controller (S08USBV1) 17.4.1.5 USB On-Chip Voltage Regulator (VREG) The on-chip 3.3-V regulator provides a stable power source to power the USB internal transceiver and provide for the termination of an internal or external pullup resistor. When the on-chip regulator is enabled, it requires a voltage supply input in the range from 3.9 V to 5.5 V, and the voltage regulator output will be in the range of 3.0 V to 3.6 V. With a dedicated on-chip USB 3.3-V regulator and a separate power supply for the MCU, the MCU and USB can operate at different voltages (See the USB electricals regarding the USB voltage regulator electrical characteristics). When the on-chip 3.3-V regulator is disabled, a 3.3-V source must be provided through the V pin to power the USB transceiver. In this case, the power supply voltage to the MCU USB33 must not fall below the input voltage at the V pin. USB33 The 3.3-V regulator has 3 modes including: • Active mode — This mode is entered when USB is active. Current requirement is sufficient to power the transceiver and the USBDP pullup resistor. • Standby — The voltage regulator standby mode is entered automatically when the USB device is in suspend mode. When the USB device is forced into suspend mode by the USB bus, the firmware must configure the MCU for stop3 mode. In standby mode, the requirement is to maintain the USBDP pin voltage at 3.0 V to 3.6 V, with a 900 Ω (worst-case) pullup. • Power off — This mode is entered anytime when stop2 or stop1 is entered or when the voltage regulator is disabled. 17.4.1.6 USB On-Chip USBDP Pullup Resistor The pullup resistor on the USBDP line required for full-speed operation by the USB Specification Rev. 2.0 can be internal or external to the MCU, depending on the application requirements. An on-chip pullup resistor, implemented as specified in the USB 2.0 resistor ECN, is optionally available via firmware configuration. Alternatively, this on-chip pullup resistor can be disabled, and the USB module can be configured to use an external pullup resistor for the USBDP line instead. If using an external pullup resistor on the USBDP line, the resistor must comply with the requirements in the USB 2.0 resistor ECN found at http://www.usb.org. The USBPU bit in the USBCTL0 register can be used to indicate if the pullup resistor is internal or external to the MCU. If USBPU is clear, the internal pullup resistor on USBDP is disabled, and an external USBDP pullup can be used. When using an external USBDP pullup, if the voltage regulator is enabled, the V USB33 voltage output can be used with the USBDP pullup. While the use of the internal USBDP pullup resistor is generally recommended, the figure below shows the USBDP pullup resistor configuration for a USB device using an external resistor tied to V . USB33 MC9S08JM60 Series Data Sheet, Rev. 5 312 Freescale Semiconductor

Universal Serial Bus Device Controller (S08USBV1) USB DEVICE 3.3 V V USB33 R DPPU USBDP USBDN Figure17-18. USBDP/USBDN Pullup Resistor Configuration for USB module 17.4.1.7 USB Powering and USBDP Pullup Enable Options The USB module provides a single-chip solution for USB device applications that are self-powered or bus-powered. The USB device needs to know when it has a valid USB connection in order to enable or disable the pullup resistor on the USBDP line. For the USB module on this device, the pullup on USBDP is only applied when a valid VBUS connection is sensed, as required by the USB specification. In bus-powered applications, system power must be derived from VBUS. Because VBUS is only available when a valid USB connection from host to device is made, the VBUS sensing is built-in, and the USBDP pullup can be enabled accordingly. With self-powered applications, determining when a valid USB connection is made is different from that of bus-powered applications. In self-powered applications, VBUS sensing must be built into the application. For instance, a KBI pin interrupt can be utilized (if available). When a valid VBUS connection is made, the KBI interrupt can notify the application that a valid USB connection is available, and the internal pullup resistor can be enabled using the USBPU bit. If an external pullup resistor is used instead of the internal one, the VBUS sensing mechanism must be included in the system design. Table 17-20 summarizes the differences in enabling the USBDP pullup for different USB power modes. Table17-20. USBDP Pullup Enable for Different USB Power Modes Power USBDP Pullup Pullup Enable Bus Power Internal Set USBPU bit (Built-in VBUS sense) External Build into application Self Power Internal Set USBPU bit (Build VBUS sense into application) External Build into application MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 313

Universal Serial Bus Device Controller (S08USBV1) 17.4.2 Buffer Descriptor Table (BDT) To efficiently manage USB endpoint communications, the USB module implements a buffer descriptor table (BDT) comprised of buffer descriptors (BD) in the local USB RAM. The BD entries provide status or control information for a corresponding endpoint. The BD entries also provide an address to the endpoint’s buffer. A single BD for an endpoint direction requires 3-bytes. A detailed description of the BDT format is provided in the next sections. The software API intelligently manages buffers for the USB module by updating the BDT when needed. This allows the USB module to efficiently handle data transmission and reception, while the microcontroller performs communication overhead processing and other function dependent applications. Because the buffers are shared between the microcontroller and the USB module, a simple semaphore mechanism is used to distinguish who is allowed to update the BDT and buffers in buffer memory. A semaphore bit, the OWN bit, is cleared to 0 when the BD entry is owned by the microcontroller. The microcontroller is allowed read and write access to the BD entry and the data buffer when the OWN bit is 0. When the OWN bit is set to 1, the BD entry and the data buffer are owned by the USB module. The USB module now has full read and write access and the microcontroller must not modify the BD or its corresponding data buffer. 17.4.2.1 Multiple Buffer Descriptor Table Entries for a Single Endpoint Every endpoint direction requires at least one three-byte Buffer Descriptor entry. Thus, endpoint 0, a bidirectional control endpoint, requires one BDT entry for the IN direction, and one for the OUT direction. Using two BD entries also allows for double-buffering. Double-buffering BDs allows the USB module to easily transfer data at the maximum throughput provided by the USB module. Double buffering allows the MCU to process one BD while the USB module is processing the other BD. To facilitate double-buffering, two buffer descriptor (BD) entries are needed for each endpoint direction. One BD entry is the EVEN BD and the other is the ODD BD. 17.4.2.2 Addressing Buffer Descriptor Table Entries The BDT addressing is hardwired into the module. The BDT occupies the first portion of the USB RAM. To access endpoint data via the USB or MCU, the addressing mechanism of the buffer descriptor table must be understood. All enabled IN and OUT endpoint BD entries are indexed into the BDT to allow easy access via the USB module or the MCU. The figure below shows the USB RAM organization. The figure shows that the first entries in the USB RAM are dedicated to storage of the BDT entries - i.e. the first 30 bytes of the USB RAM (0x00 to 0x1D) are used to implement the BDT. MC9S08JM60 Series Data Sheet, Rev. 5 314 Freescale Semiconductor

Universal Serial Bus Device Controller (S08USBV1) Table17-21. USB RAM Organization USB RAM USB RAM Description of Contents Offset 0x00 Endpoint 0 IN Endpoint 0, OUT Endpoint 1 Endpoint 2 Endpoint 3 BDT Endpoint 4 Endpoint 5, Buffer EVEN Endpoint 5, Buffer ODD Endpoint 6, Buffer EVEN 0x1D Endpoint 6, Buffer ODD 0x1E RESERVED 0x1F RESERVED 0x20 USB RAM available for endpoint buffers 0xFF When the USB module receives a USB token on an enabled endpoint, it interrogates the BDT. The USB module reads the corresponding endpoint BD entry and determines if it owns the BD and corresponding data buffer. 17.4.2.3 Buffer Descriptor Formats The buffer descriptors (BDs) are groups of registers that provide endpoint buffer control information for the USB module and the MCU. The BDs have different meanings based on who is reading the BD in memory. The USB module uses the data stored in the BDs to determine: • Who owns the buffer in system memory • Data0 or Data1 PID • Release Own upon packet completion • Data toggle synchronization enable • How much data to be transmitted or received • Where the buffer resides in the buffer RAM. The microcontroller uses the data stored in the BDs to determine: • Who owns the buffer in system memory • Data0 or Data1 PID • The received TOKEN PID MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 315

Universal Serial Bus Device Controller (S08USBV1) • How much data was transmitted or received. • Where the buffer resides in buffer memory The BDT is composed of buffer descriptors (BD) which are used to define and control the actual buffers in the USB RAM space. BDs always occur as a 3-bytes block. See Figure17-19 for the BD example of Endpoint 0 IN start from USB RAM offset 0x00. The format for the buffer descriptor is shown in Table 17-22. Offset 7 6 5 4 3 2 1 0 R BDTKPID[3] BDTKPID[3] BDTKPID[1] BDTKPID[0] 0x00 OWN DATA0/1 0 0 W 0 0 DTS BDTSTALL R 0x01 BC[7:0] W R 0x02 EPADR[9:4] W Figure17-19. Buffer Descriptor Example Table17-22. Buffer Descriptor Table Fields Field Description OWN — This OWN bit determines who currently owns the buffer. The USB SIE generally writes a 0 to this bit OWN when it has completed a token. The USB module ignores all other fields in the BD when OWN=0. Once the BD has been assigned to the USB module (OWN=1), the MCU must not change it in any way. This byte of the BD must always be the last byte the MCU (firmware) updates when it initializes a BD. Although the hardware will not block the MCU from accessing the BD while owned by the USB SIE, doing so may cause undefined behavior and is generally not recommended. 0 The MCU has exclusive access to the entire BD 1 The USB module has exclusive access to the BD Data Toggle — This bit defines if a DATA0 field (DATA0/1=0) or a DATA1 (DATA0/1=1) field was transmitted or DATA0/1 received. It is unchanged by the USB module. 0 Data 0 packet 1 Data 1 packet The current token PID is written back to the BD by the USB module when a transfer completes. The values BDTKPID[3:0] written back are the token PID values from the USB specification: 0x1 for an OUT token, 0x9 for and IN token or 0xd for a SETUP token. Data Toggle Synchronization— This bit enables data toggle synchronization. DTS 0 No data toggle synchronization is performed. 1 Data toggle synchronization is performed. BDT Stall — Setting this bit will cause the USB module to issue a STALL handshake if a token is received by BDTSTALL the SIE that would use the BDT in this location. The BDT is not consumed by the SIE (the OWN bit remains and the rest of the BD is unchanged) when the BDTSTALL bit is set. 0 BDT stall is disabled 1 USB will issue a STALL handshake if a token is received by the SIE that would use the BDT in this location MC9S08JM60 Series Data Sheet, Rev. 5 316 Freescale Semiconductor

Universal Serial Bus Device Controller (S08USBV1) Table17-22. Buffer Descriptor Table Fields (continued) Field Description Byte Count — The Byte Count bits represent the 8-bit byte count. The USB module serial interface engine BC[7:0] (SIE) will change this field upon the completion of a RX transfer with the byte count of the data received. Note that while USB supports packets as large as 1023 bytes for isochronous endpoints, this module limits packet size to 64 bytes. Endpoint Address— The endpoint address bits represent the upper 6 bits of the 10-bit buffer address within EPADR[9:4] the module’s local USB RAM. Bits [3:0] of EPADR are always zero, therefore the address of the buffer must always start on a 16-byte aligned address within the local RAM. These bits are unchanged by the USB module. This is NOT the address of the memory on the system bus. EPADR is relative to the start of the local USB RAM. 17.4.3 USB Transactions When the USB module transmits or receives data, it will first compute the BDT address based on the endpoint number, data direction, and which buffer is being used (even or odd), then it will read the BD. Once the BD has been read, and if the OWN bit equals 1, the serial interface engine (SIE) will transfer the packet data to or receive the packet data from the buffer pointed to by the EPADR field of the BD. When the USB TOKEN is complete, the USB module will update the BDT and change the OWN bit to 0. The STAT register is updated and the TOKDNE interrupt is set. When the microcontroller processes the TOKDNE interrupt, it reads the status register. This gives the microcontroller all the information it needs to process the endpoint. At this point the microcontroller can allocate a new BD, so additional USB data can be transmitted or received for that endpoint, and it can process the previous BD. Figure 17-20 shows a timeline for how a typical USB token would be processed. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 317

Universal Serial Bus Device Controller (S08USBV1) = USB Host = Function USB RST SOF USBRST SOF Interrupt Generated Interrupt Generated SETUP TOKEN DATA ACK TOKDNE Interrupt Generated IN TOKEN DATA ACK TOKDNE Interrupt Generated OUT TOKEN DATA ACK TOKDNE Interrupt Generated Figure17-20. USB Packet Flow The USB has two sources of data overrun error: • The memory latency to the local USB RAM interface may be too high and cause the receive buffer to overflow. This is predominantly a hardware performance issue, usually caused by transient memory access issues. • The packet received may be larger than the negotiated MAXPACKET size. This is caused by a software bug. In the first case, the USB will respond with a NAK or bus timeout (BTO) as appropriate for the class of transaction. The BTOERR bit will be set in the ERRSTAT register. Depending on the values of the INTENB and ERRENB register, USB module may assert an interrupt to notify the CPU of the error. In device mode the BDT is not written back nor is the TOKDNE interrupt triggered because it is assumed that a second attempt will be queued at future time and will succeed. In the second case of oversized data packets, the USB specification assumes correct software drivers on both sides. The overrun is not due to memory latency but to a lack of space to put the excess data. NAK'ing the packet will likely cause another retransmission of the already oversized packet data. In response to oversized packets, the USB module will still ACK the packet for non-isochronous transfers. The data written to memory is clipped to the MAXPACKET size so as not to corrupt the buffer space. The USB module will assert the BUFERRF bit of the ERRSTAT register (which could trigger an interrupt, as above) and a TOKDNE interrupt fails. The BDTKPID field of the BDT will not be “1111” because the BUFERRF is not due to latency. The packet length field written back to the BDT will be the MAXPACKET value to represent the length of the clipped data actually written to memory. From here the software can decide an MC9S08JM60 Series Data Sheet, Rev. 5 318 Freescale Semiconductor

Universal Serial Bus Device Controller (S08USBV1) appropriate course of action for future transactions — stalling the endpoint, canceling the transfer, disabling the endpoint, etc. 17.4.4 USB Packet Processing Packet processing for a USB device consists of managing buffers for IN (to the USB Host) and OUT (to the USB device) transactions. Packet processing is further divided into request processing on Endpoint 0, and data packet processing on the data endpoints. 17.4.4.1 USB Data Pipe Processing Data pipe processing is essentially a buffer management task. The firmware is responsible for managing the shared buffer RAM to ensure that a BD is always ready for the hardware to process (OWN bit = 1). The device allocates buffers within the shared RAM, sets up the buffer descriptors, and waits for interrupts. On receipt of a TOKDNE interrupt, the firmware reads the STAT register to determine which endpoint is affected, then reads the corresponding BDT entry to determine what to do next. When processing data packets, firmware is responsible for managing the size of the packet buffers to be in compliance with the USB specification, and the physical limitations of this module. Packet sizes up to 64 bytes are supported on all endpoints. Isochronous endpoints also can only specify packet sizes up to 64 bytes. Firmware is also responsible for setting the appropriate bits in the BDT. For most applications using bulk packets (control, bulk, and interrupt-type transfers), the firmware will set the DTS, BC and EPADR fields for each BD. For isochronous packets, firmware will set BC and EPADR fields. In all cases, firmware will set the OWN bit to enable the endpoint for data transfers. 17.4.4.2 Request Processing on Endpoint 0 In most cases, commands to the USB device are directed to Endpoint 0. The host uses the “Standard Requests” described in Chapter 9 of the USB specification to enumerate and configure the device. Class drivers or product specific drivers running on the host send class (HID, Mass Storage, Imaging) and vendor specific commands to the device on endpoint 0. USB requests always follow a specific format: • Host sends a SETUP token, followed by an 8-byte setup packet, and the device hardware can send a handshake packet. • If the setup packet specifies a data phase, the host and device may transfer up to 64 Kbytes of data (either IN or OUT, not both). • The request is terminated by a status phase. Device firmware monitors the INTSTAT and STAT registers, the endpoint 0 buffer descriptors (BD’s), and the contents of the setup packet to correctly execute the host’s request. The flow for processing endpoint 0 requests is as follows: 1. Allocate 8-byte buffers for endpoint 0 OUT. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 319

Universal Serial Bus Device Controller (S08USBV1) 2. Create BDT entries for Endpoint 0 OUT, and set the DTS and OWN bits to 1. 3. Wait for interrupt TOKDNE. 4. Read STAT register. — The status register must show Endpoint 0, RX. If it does not, then assert the EPSTALL bit in the endpoint control register. 5. Read Endpoint 0 OUT BD. — Verify that the token type is a SETUP token. If it is not, then assert the EPSTALL bit in the endpoint control register. 6. Decode and process the setup packet. — If the direction field in the setup packet indicates an OUT transfer, then process the out data phase to receive exactly the number of bytes specified in the wLength field of the setup packet. — If the direction field in the setup packet indicates an IN transfer, then process the in data phase to deliver no more than the number of bytes specified in the wLength field. Note that it is common for the host to request more bytes than it needs, expecting the device to only send as much as it needs to. 7. After processing the data phase (if there was one), create a zero-byte status phase transaction. — This is accomplished for an OUT data phase (IN status phase) by setting the BC to 0 in the next BD, while also setting OWN=1. For an IN data phase (OUT status phase), the host will send a zero-byte packet to the device. — Firmware can verify completion of the data phase by verifying the received token in the BD on receipt of the TOKDNE interrupt. If the data phase was of type IN, then the status phase token will be OUT. If the data phase was of type OUT, then the status phase token will be IN. 17.4.4.3 Endpoint 0 Exception Conditions The USB includes a number of error checking and recovery mechanisms to ensure reliable data transfer. One such exception occurs when the host sends a SETUP packet to a device, and the host never receives the acknowledge handshake from the device. In this case, the host will retry the SETUP packet. Endpoint 0 request handlers on the device must be aware of the possibility that after receiving a correct SETUP packet, they could receive another SETUP packet before the data phase actually begins. 17.4.5 Start of Frame Processing The USB host allocates time in 1.0 ms chunks called “Frames” for the purposes of packet scheduling. The USB host starts each frame with a broadcast token called SOF (start of frame) that includes an 11-bit sequence number. The TOKSOF interrupt is used to notify firmware when an SOF token was received. Firmware can read the current frame number from the FRMNUML/FRMNUMH registers. In general, the SOF interrupt is only monitored by devices using isochronous endpoints to help ensure that the device and host remain synchronized. MC9S08JM60 Series Data Sheet, Rev. 5 320 Freescale Semiconductor

Universal Serial Bus Device Controller (S08USBV1) 17.4.6 Suspend/Resume The USB supports a single low-power mode called suspend. Getting into and out of the suspend state is described in the following sections. 17.4.6.1 Suspend The USB host can put a single device or the entire bus into the suspend state at any time. The MCU supports suspend mode for low power. Suspend mode will be entered when the USB data lines are in the idle state for more than 3 ms. Entry into suspend mode is announced by the SLEEPF bit in the INTSTAT register. Per the USB specification, a low-power bus-powered USB device is required to draw less than 500 µA in suspend state. A high-power device that supports remote wakeup and has its remote wake-up feature enabled by the host can draw up to 2.5 mA of current. After the initial 3-ms idle, the USB device will reach this state within 7 ms. This low-current requirement means that firmware is responsible for entering stop3 mode once the SLEEPF flag has been set and before the USB module has been placed in the suspend state. On receipt of resume signaling from the USB, the module can generate an asynchronous interrupt to the MCU which brings the device out of stop mode and wakes up the clocks. Setting the USBRESMEN bit in the USBCTL0 register immediately after the SLEEPF bit is set enables this asynchronous notification feature. The USB resume signaling will then cause the LPRESF bit to be set, indicating a low-power SUSPEND resume, which will wake the CPU from stop3 mode. During normal operation, while the host is sending SOF packets, the USB module will not enter suspend mode. 17.4.6.2 Resume There are three ways to get out of the suspend state. When the USB module is in suspend state, the resume detection is active even if all the clocks are disabled and the MCU is in stop3 mode. The MCU can be activated from the suspend state by normal bus activity, a USB reset signal, or upstream resume (remote wakeup). 17.4.6.2.1 Host Initiated Resume The host signals a resume from suspend by initiating resume signaling (K state) for at least 20 ms followed by a standard low-speed EOP signal. This 20 ms ensures that all devices in the USB network are awakened. After resuming the bus, the host must begin sending bus traffic within 3 ms to prevent the device from re-entering suspend mode. Depending on the power mode the device is in while suspended, the notification for a host initiated resume will be different: • Run mode - RESUME must be set after SLEEPF becomes set to enable the RESUMEF interrupt. Then, upon resume signaling, the RESUMEF interrupt will trigger after a K-state has been observed on the USBDP/USBDN lines for 2.5 µs. • Stop3 mode - USBRESMEN must be set after SLEEPF becomes set to arm the LPRESF bit. Then, upon a K-state on the bus while the device is in stop3 mode, the LPRESF bit will be set, indicating MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 321

Universal Serial Bus Device Controller (S08USBV1) a resume from low-power suspend. This will trigger an asynchronous interrupt to wake the CPU from stop3 mode and resume clocks to the USB module. NOTE As a precaution, after LPRESF is set, firmware must check the state of the USB bus to see if the K-state was a result of a transient event and not a true host-initiated resume. If this is the case, then the device can drop back into stop3 if necessary. To do this, the RESUME interrupt can be enabled in conjunction with the USBRESMEN feature. Then, after LPRESF is set, and a K-state is still detected approximately 2.5 µs after clocks have restarted, firmware can check that the RESUMEF interrupt has triggered, indicating resume signaling from the host. 17.4.6.2.2 USB Reset Signaling Reset can wake a device from the suspend state. 17.4.6.2.3 Remote Wakeup The USB device can send a resume event to the host by writing to the CRESUME bit. Firmware must first set the bit for the time period required by the USB Specification Rev. 2.0 (Section 7.1.7.7) and then clear it to 0. 17.4.7 Resets The module supports multiple types of resets. The first is a bus reset generated by the USB Host, the second is a module reset generated by the MCU. 17.4.7.1 USB Bus Reset At any time, the USB host may issue a reset to one or all of the devices attached to the bus. A USB reset is defined as a period of single ended zero (SE0) on the cable for greater than 2.5 μs. When the device detects reset signaling, it resets itself to the unconfigured state, and sets its USB address zero. The USB host uses reset signaling to force one or all connected devices into a known state prior to commencing enumeration. The USB module responds to reset signaling by asserting the USBRST interrupt in the INTSTAT register. Software is required to service this interrupt to ensure correct operation of the USB. 17.4.7.2 USB Module Reset USB module resets are initiated on-chip. During a module reset, the USB module is configured in the default mode. The USB module can also be forced into its reset state by setting the USBRESET bit in the USBCTL0 register. The default mode includes the following settings: • Interrupts masked. • USB clock enabled • USB voltage regulator disabled MC9S08JM60 Series Data Sheet, Rev. 5 322 Freescale Semiconductor

Universal Serial Bus Device Controller (S08USBV1) • USB transceiver disabled • USBDP pullup disabled • Endpoints disabled • USB address register set to zero 17.4.8 Interrupts Interrupts from the INTSTAT register signify events which occur during normal operation — USB start of frame tokens (TOKSOF), packet completion (TOKDNE), USB bus reset (USBRST), endpoint errors (ERROR), suspend and resume (SLEEP and RESUME), and endpoint stalled (STALL). The ERRSTAT interrupts carry information about specific types of errors, which is needed on an application specific basis. Using ERRSTAT, an application can determine exactly why a packet transfer failed — due to CRC error, PID check error and so on. Both registers are maskable via the INTENB and ERRENB registers. The INTSTAT and ERRSTAT are used to signal interrupts in a two-level structure. Unmasked interrupts from the ERRSTAT register are reported in the INTSTAT register. Note that the interrupt registers work in concert with the STAT register. On receipt of an INTSTAT interrupt, software can check the STAT register and determine which BDT entry was affected by the transaction. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 323

Universal Serial Bus Device Controller (S08USBV1) MC9S08JM60 Series Data Sheet, Rev. 5 324 Freescale Semiconductor

Chapter 18 Development Support 18.1 Introduction Development support systems in the HCS08 include the background debug controller (BDC) and the on-chip debug module (DBG). The BDC provides a single-wire debug interface to the target MCU that provides a convenient interface for programming the on-chip flash and other nonvolatile memories. The BDC is also the primary debug interface for development and allows non-intrusive access to memory data and traditional debug features such as CPU register modify, breakpoints, and single instruction trace commands. In the HCS08 family, address and data bus signals are not available on external pins (not even in test modes). Debug is done through commands fed into the target MCU via the single-wire background debug interface. The debug module provides a means to selectively trigger and capture bus information so an external development system can reconstruct what happened inside the MCU on a cycle-by-cycle basis without having external access to the address and data signals. The alternate BDC clock source for MC9S08JM60 Series is the MCGLCLK. See Chapter 12, “Multi-Purpose Clock Generator (S08MCGV1),” for more information about MCGLCLK and how to select clock sources. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 325

Development Support 18.1.1 Features Features of the BDC module include: • Single pin for mode selection and background communications • BDC registers are not located in the memory map • SYNC command to determine target communications rate • Non-intrusive commands for memory access • Active background mode commands for CPU register access • GO and TRACE1 commands • BACKGROUND command can wake CPU from stop or wait modes • One hardware address breakpoint built into BDC • Oscillator runs in stop mode, if BDC enabled • COP watchdog disabled while in active background mode Features of the ICE system include: • Two trigger comparators: Two address + read/write (R/W) or one full address + data + R/W • Flexible 8-word by 16-bit FIFO (first-in, first-out) buffer for capture information: — Change-of-flow addresses or — Event-only data • Two types of breakpoints: — Tag breakpoints for instruction opcodes — Force breakpoints for any address access • Nine trigger modes: — Basic: A-only, A OR B — Sequence: A then B — Full: A AND B data, A AND NOT B data — Event (store data): Event-only B, A then event-only B — Range: Inside range (A ≤ address ≤ B), outside range (address < A or address > B) 18.2 Background Debug Controller (BDC) All MCUs in the HCS08 family contain a single-wire background debug interface that supports in-circuit programming of on-chip nonvolatile memory and sophisticated non-intrusive debug capabilities. Unlike debug interfaces on earlier 8-bit MCUs, this system does not interfere with normal application resources. It does not use any user memory or locations in the memory map and does not share any on-chip peripherals. BDC commands are divided into two groups: • Active background mode commands require that the target MCU is in active background mode (the user program is not running). Active background mode commands allow the CPU registers to be read or written, and allow the user to trace one user instruction at a time, or GO to the user program from active background mode. MC9S08JM60 Series Data Sheet, Rev. 5 326 Freescale Semiconductor

Development Support • Non-intrusive commands can be executed at any time even while the user’s program is running. Non-intrusive commands allow a user to read or write MCU memory locations or access status and control registers within the background debug controller. Typically, a relatively simple interface pod is used to translate commands from a host computer into commands for the custom serial interface to the single-wire background debug system. Depending on the development tool vendor, this interface pod may use a standard RS-232 serial port, a parallel printer port, or some other type of communications such as a universal serial bus (USB) to communicate between the host PC and the pod. The pod typically connects to the target system with ground, the BKGD pin, RESET, and sometimes V . An open-drain connection to reset allows the host to force a target system reset, DD which is useful to regain control of a lost target system or to control startup of a target system before the on-chip nonvolatile memory has been programmed. Sometimes V can be used to allow the pod to use DD power from the target system to avoid the need for a separate power supply. However, if the pod is powered separately, it can be connected to a running target system without forcing a target system reset or otherwise disturbing the running application program. BKGD 1 2 GND NO CONNECT 3 4 RESET NO CONNECT 5 6 V DD Figure18-1. BDM Tool Connector 18.2.1 BKGD Pin Description BKGD is the single-wire background debug interface pin. The primary function of this pin is for bidirectional serial communication of active background mode commands and data. During reset, this pin is used to select between starting in active background mode or starting the user’s application program. This pin is also used to request a timed sync response pulse to allow a host development tool to determine the correct clock frequency for background debug serial communications. BDC serial communications use a custom serial protocol first introduced on the M68HC12 Family of microcontrollers. This protocol assumes the host knows the communication clock rate that is determined by the target BDC clock rate. All communication is initiated and controlled by the host that drives a high-to-low edge to signal the beginning of each bit time. Commands and data are sent most significant bit first (MSB first). For a detailed description of the communications protocol, refer to Section18.2.2, “Communication Details.” If a host is attempting to communicate with a target MCU that has an unknown BDC clock rate, a SYNC command may be sent to the target MCU to request a timed sync response signal from which the host can determine the correct communication speed. BKGD is a pseudo-open-drain pin and there is an on-chip pullup so no external pullup resistor is required. Unlike typical open-drain pins, the external RC time constant on this pin, which is influenced by external capacitance, plays almost no role in signal rise time. The custom protocol provides for brief, actively driven speedup pulses to force rapid rise times on this pin without risking harmful drive level conflicts. Refer to Section18.2.2, “Communication Details,” for more detail. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 327

Development Support When no debugger pod is connected to the 6-pin BDM interface connector, the internal pullup on BKGD chooses normal operating mode. When a debug pod is connected to BKGD it is possible to force the MCU into active background mode after reset. The specific conditions for forcing active background depend upon the HCS08 derivative (refer to the introduction to this Development Support section). It is not necessary to reset the target MCU to communicate with it through the background debug interface. 18.2.2 Communication Details The BDC serial interface requires the external controller to generate a falling edge on the BKGD pin to indicate the start of each bit time. The external controller provides this falling edge whether data is transmitted or received. BKGD is a pseudo-open-drain pin that can be driven either by an external controller or by the MCU. Data is transferred MSB first at 16BDC clock cycles per bit (nominal speed). The interface times out if 512BDC clock cycles occur between falling edges from the host. Any BDC command that was in progress when this timeout occurs is aborted without affecting the memory or operating mode of the target MCU system. The custom serial protocol requires the debug pod to know the target BDC communication clock speed. The clock switch (CLKSW) control bit in the BDC status and control register allows the user to select the BDC clock source. The BDC clock source can either be the bus or the alternate BDC clock source. The BKGD pin can receive a high or low level or transmit a high or low level. The following diagrams show timing for each of these cases. Interface timing is synchronous to clocks in the target BDC, but asynchronous to the external host. The internal BDC clock signal is shown for reference in counting cycles. MC9S08JM60 Series Data Sheet, Rev. 5 328 Freescale Semiconductor

Development Support Figure 18-2 shows an external host transmitting a logic 1 or 0 to the BKGD pin of a target HCS08 MCU. The host is asynchronous to the target so there is a 0-to-1 cycle delay from the host-generated falling edge to where the target perceives the beginning of the bit time. Ten target BDC clock cycles later, the target senses the bit level on the BKGD pin. Typically, the host actively drives the pseudo-open-drain BKGD pin during host-to-target transmissions to speed up rising edges. Because the target does not drive the BKGD pin during the host-to-target transmission period, there is no need to treat the line as an open-drain signal during this period. BDC CLOCK (TARGET MCU) HOST TRANSMIT 1 HOST TRANSMIT 0 10 CYCLES EARLIEST START OF NEXT BIT SYNCHRONIZATION TARGET SENSES BIT LEVEL UNCERTAINTY PERCEIVED START OF BIT TIME Figure18-2. BDC Host-to-Target Serial Bit Timing MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 329

Development Support Figure 18-3 shows the host receiving a logic 1 from the target HCS08 MCU. Because the host is asynchronous to the target MCU, there is a 0-to-1 cycle delay from the host-generated falling edge on BKGD to the perceived start of the bit time in the target MCU. The host holds the BKGD pin low long enough for the target to recognize it (at least two target BDC cycles). The host must release the low drive before the target MCU drives a brief active-high speedup pulse seven cycles after the perceived start of the bit time. The host should sample the bit level about 10cycles after it started the bit time. BDC CLOCK (TARGET MCU) HOST DRIVE TO BKGD PIN HIGH-IMPEDANCE TARGET MCU SPEEDUP PULSE HIGH-IMPEDANCE HIGH-IMPEDANCE PERCEIVED START OF BIT TIME R-C RISE BKGD PIN 10 CYCLES EARLIEST START OF NEXT BIT 10 CYCLES HOST SAMPLES BKGD PIN Figure18-3. BDC Target-to-Host Serial Bit Timing (Logic 1) MC9S08JM60 Series Data Sheet, Rev. 5 330 Freescale Semiconductor

Development Support Figure 18-4 shows the host receiving a logic 0 from the target HCS08 MCU. Because the host is asynchronous to the target MCU, there is a 0-to-1 cycle delay from the host-generated falling edge on BKGD to the start of the bit time as perceived by the target MCU. The host initiates the bit time but the target HCS08 finishes it. Because the target wants the host to receive a logic 0, it drives the BKGD pin low for 13 BDC clock cycles, then briefly drives it high to speed up the rising edge. The host samples the bit level about 10 cycles after starting the bit time. BDC CLOCK (TARGET MCU) HOST DRIVE HIGH-IMPEDANCE TO BKGD PIN SPEEDUP TARGET MCU PULSE DRIVE AND SPEED-UP PULSE PERCEIVED START OF BIT TIME BKGD PIN 10 CYCLES EARLIEST START OF NEXT BIT 10 CYCLES HOST SAMPLES BKGD PIN Figure18-4. BDM Target-to-Host Serial Bit Timing (Logic 0) MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 331

Development Support 18.2.3 BDC Commands BDC commands are sent serially from a host computer to the BKGD pin of the target HCS08 MCU. All commands and data are sent MSB-first using a custom BDC communications protocol. Active background mode commands require that the target MCU is currently in the active background mode while non-intrusive commands may be issued at any time whether the target MCU is in active background mode or running a user application program. Table 18-1 shows all HCS08 BDC commands, a shorthand description of their coding structure, and the meaning of each command. Coding Structure Nomenclature This nomenclature is used in Table 18-1 to describe the coding structure of the BDC commands. Commands begin with an 8-bit hexadecimal command code in the host-to-target direction (most significant bit first) / = separates parts of the command d = delay 16 target BDC clock cycles AAAA = a 16-bit address in the host-to-target direction RD = 8 bits of read data in the target-to-host direction WD = 8 bits of write data in the host-to-target direction RD16 = 16 bits of read data in the target-to-host direction WD16 = 16 bits of write data in the host-to-target direction SS = the contents of BDCSCR in the target-to-host direction (STATUS) CC = 8 bits of write data for BDCSCR in the host-to-target direction (CONTROL) RBKP = 16 bits of read data in the target-to-host direction (from BDCBKPT breakpoint register) WBKP = 16 bits of write data in the host-to-target direction (for BDCBKPT breakpoint register) MC9S08JM60 Series Data Sheet, Rev. 5 332 Freescale Semiconductor

Development Support Table18-1. BDC Command Summary Command Active BDM/ Coding Description Mnemonic Non-intrusive Structure Request a timed reference pulse to determine SYNC Non-intrusive n/a1 target BDC communication speed Enable acknowledge protocol. Refer to ACK_ENABLE Non-intrusive D5/d Freescale document order no. HCS08RMv1/D. Disable acknowledge protocol. Refer to ACK_DISABLE Non-intrusive D6/d Freescale document order no. HCS08RMv1/D. Enter active background mode if enabled BACKGROUND Non-intrusive 90/d (ignore if ENBDM bit equals 0) READ_STATUS Non-intrusive E4/SS Read BDC status from BDCSCR WRITE_CONTROL Non-intrusive C4/CC Write BDC controls in BDCSCR READ_BYTE Non-intrusive E0/AAAA/d/RD Read a byte from target memory READ_BYTE_WS Non-intrusive E1/AAAA/d/SS/RD Read a byte and report status Re-read byte from address just read and report READ_LAST Non-intrusive E8/SS/RD status WRITE_BYTE Non-intrusive C0/AAAA/WD/d Write a byte to target memory WRITE_BYTE_WS Non-intrusive C1/AAAA/WD/d/SS Write a byte and report status READ_BKPT Non-intrusive E2/RBKP Read BDCBKPT breakpoint register WRITE_BKPT Non-intrusive C2/WBKP Write BDCBKPT breakpoint register Go to execute the user application program GO Active BDM 08/d starting at the address currently in the PC Trace 1 user instruction at the address in the TRACE1 Active BDM 10/d PC, then return to active background mode Same as GO but enable external tagging TAGGO Active BDM 18/d (HCS08 devices have no external tagging pin) READ_A Active BDM 68/d/RD Read accumulator (A) READ_CCR Active BDM 69/d/RD Read condition code register (CCR) READ_PC Active BDM 6B/d/RD16 Read program counter (PC) READ_HX Active BDM 6C/d/RD16 Read H and X register pair (H:X) READ_SP Active BDM 6F/d/RD16 Read stack pointer (SP) Increment H:X by one then read memory byte READ_NEXT Active BDM 70/d/RD located at H:X Increment H:X by one then read memory byte READ_NEXT_WS Active BDM 71/d/SS/RD located at H:X. Report status and data. WRITE_A Active BDM 48/WD/d Write accumulator (A) WRITE_CCR Active BDM 49/WD/d Write condition code register (CCR) WRITE_PC Active BDM 4B/WD16/d Write program counter (PC) WRITE_HX Active BDM 4C/WD16/d Write H and X register pair (H:X) WRITE_SP Active BDM 4F/WD16/d Write stack pointer (SP) Increment H:X by one, then write memory byte WRITE_NEXT Active BDM 50/WD/d located at H:X Increment H:X by one, then write memory byte WRITE_NEXT_WS Active BDM 51/WD/d/SS located at H:X. Also report status. 1 The SYNC command is a special operation that does not have a command code. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 333

Development Support The SYNC command is unlike other BDC commands because the host does not necessarily know the correct communications speed to use for BDC communications until after it has analyzed the response to the SYNC command. To issue a SYNC command, the host: • Drives the BKGD pin low for at least 128 cycles of the slowest possible BDC clock (The slowest clock is normally the reference oscillator/64 or the self-clocked rate/64.) • Drives BKGD high for a brief speedup pulse to get a fast rise time (This speedup pulse is typically one cycle of the fastest clock in the system.) • Removes all drive to the BKGD pin so it reverts to high impedance • Monitors the BKGD pin for the sync response pulse The target, upon detecting the SYNC request from the host (which is a much longer low time than would ever occur during normal BDC communications): • Waits for BKGD to return to a logic high • Delays 16cycles to allow the host to stop driving the high speedup pulse • Drives BKGD low for 128BDC clock cycles • Drives a 1-cycle high speedup pulse to force a fast rise time on BKGD • Removes all drive to the BKGD pin so it reverts to high impedance The host measures the low time of this 128-cycle sync response pulse and determines the correct speed for subsequent BDC communications. Typically, the host can determine the correct communication speed within a few percent of the actual target speed and the communication protocol can easily tolerate speed errors of several percent. 18.2.4 BDC Hardware Breakpoint The BDC includes one relatively simple hardware breakpoint that compares the CPU address bus to a 16-bit match value in the BDCBKPT register. This breakpoint can generate a forced breakpoint or a tagged breakpoint. A forced breakpoint causes the CPU to enter active background mode at the first instruction boundary following any access to the breakpoint address. The tagged breakpoint causes the instruction opcode at the breakpoint address to be tagged so that the CPU will enter active background mode rather than executing that instruction if and when it reaches the end of the instruction queue. This implies that tagged breakpoints can only be placed at the address of an instruction opcode while forced breakpoints can be set at any address. The breakpoint enable (BKPTEN) control bit in the BDC status and control register (BDCSCR) is used to enable the breakpoint logic (BKPTEN= 1). When BKPTEN= 0, its default value after reset, the breakpoint logic is disabled and no BDC breakpoints are requested regardless of the values in other BDC breakpoint registers and control bits. The force/tag select (FTS) control bit in BDCSCR is used to select forced (FTS= 1) or tagged (FTS= 0) type breakpoints. The on-chip debug module (DBG) includes circuitry for two additional hardware breakpoints that are more flexible than the simple breakpoint in the BDC module. MC9S08JM60 Series Data Sheet, Rev. 5 334 Freescale Semiconductor

Development Support 18.3 On-Chip Debug System (DBG) Because HCS08 devices do not have external address and data buses, the most important functions of an in-circuit emulator have been built onto the chip with the MCU. The debug system consists of an 8-stage FIFO that can store address or data bus information, and a flexible trigger system to decide when to capture bus information and what information to capture. The system relies on the single-wire background debug system to access debug control registers and to read results out of the eight stage FIFO. The debug module includes control and status registers that are accessible in the user’s memory map. These registers are located in the high register space to avoid using valuable direct page memory space. Most of the debug module’s functions are used during development, and user programs rarely access any of the control and status registers for the debug module. The one exception is that the debug system can provide the means to implement a form of ROM patching. This topic is discussed in greater detail in Section18.3.6, “Hardware Breakpoints.” 18.3.1 Comparators A and B Two 16-bit comparators (A and B) can optionally be qualified with the R/W signal and an opcode tracking circuit. Separate control bits allow you to ignore R/W for each comparator. The opcode tracking circuitry optionally allows you to specify that a trigger will occur only if the opcode at the specified address is actually executed as opposed to only being read from memory into the instruction queue. The comparators are also capable of magnitude comparisons to support the inside range and outside range trigger modes. Comparators are disabled temporarily during all BDC accesses. The A comparator is always associated with the 16-bit CPU address. The B comparator compares to the CPU address or the 8-bit CPU data bus, depending on the trigger mode selected. Because the CPU data bus is separated into a read data bus and a write data bus, the RWAEN and RWA control bits have an additional purpose, in full address plus data comparisons they are used to decide which of these buses to use in the comparator B data bus comparisons. If RWAEN= 1 (enabled) and RWA= 0 (write), the CPU’s write data bus is used. Otherwise, the CPU’s read data bus is used. The currently selected trigger mode determines what the debugger logic does when a comparator detects a qualified match condition. A match can cause: • Generation of a breakpoint to the CPU • Storage of data bus values into the FIFO • Starting to store change-of-flow addresses into the FIFO (begin type trace) • Stopping the storage of change-of-flow addresses into the FIFO (end type trace) 18.3.2 Bus Capture Information and FIFO Operation The usual way to use the FIFO is to setup the trigger mode and other control options, then arm the debugger. When the FIFO has filled or the debugger has stopped storing data into the FIFO, you would read the information out of it in the order it was stored into the FIFO. Status bits indicate the number of words of valid information that are in the FIFO as data is stored into it. If a trace run is manually halted by writing 0 to ARM before the FIFO is full (CNT = 1:0:0:0), the information is shifted by one position and MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 335

Development Support the host must perform ((8 – CNT) – 1) dummy reads of the FIFO to advance it to the first significant entry in the FIFO. In most trigger modes, the information stored in the FIFO consists of 16-bit change-of-flow addresses. In these cases, read DBGFH then DBGFL to get one coherent word of information out of the FIFO. Reading DBGFL (the low-order byte of the FIFO data port) causes the FIFO to shift so the next word of information is available at the FIFO data port. In the event-only trigger modes (see Section18.3.5, “Trigger Modes”), 8-bit data information is stored into the FIFO. In these cases, the high-order half of the FIFO (DBGFH) is not used and data is read out of the FIFO by simply reading DBGFL. Each time DBGFL is read, the FIFO is shifted so the next data value is available through the FIFO data port at DBGFL. In trigger modes where the FIFO is storing change-of-flow addresses, there is a delay between CPU addresses and the input side of the FIFO. Because of this delay, if the trigger event itself is a change-of-flow address or a change-of-flow address appears during the next two bus cycles after a trigger event starts the FIFO, it will not be saved into the FIFO. In the case of an end-trace, if the trigger event is a change-of-flow, it will be saved as the last change-of-flow entry for that debug run. The FIFO can also be used to generate a profile of executed instruction addresses when the debugger is not armed. When ARM= 0, reading DBGFL causes the address of the most-recently fetched opcode to be saved in the FIFO. To use the profiling feature, a host debugger would read addresses out of the FIFO by reading DBGFH then DBGFL at regular periodic intervals. The first eight values would be discarded because they correspond to the eight DBGFL reads needed to initially fill the FIFO. Additional periodic reads of DBGFH and DBGFL return delayed information about executed instructions so the host debugger can develop a profile of executed instruction addresses. 18.3.3 Change-of-Flow Information To minimize the amount of information stored in the FIFO, only information related to instructions that cause a change to the normal sequential execution of instructions is stored. With knowledge of the source and object code program stored in the target system, an external debugger system can reconstruct the path of execution through many instructions from the change-of-flow information stored in the FIFO. For conditional branch instructions where the branch is taken (branch condition was true), the source address is stored (the address of the conditional branch opcode). Because BRA and BRN instructions are not conditional, these events do not cause change-of-flow information to be stored in the FIFO. Indirect JMP and JSR instructions use the current contents of the H:X index register pair to determine the destination address, so the debug system stores the run-time destination address for any indirect JMP or JSR. For interrupts, RTI, or RTS, the destination address is stored in the FIFO as change-of-flow information. 18.3.4 Tag vs. Force Breakpoints and Triggers Tagging is a term that refers to identifying an instruction opcode as it is fetched into the instruction queue, but not taking any other action until and unless that instruction is actually executed by the CPU. This distinction is important because any change-of-flow from a jump, branch, subroutine call, or interrupt causes some instructions that have been fetched into the instruction queue to be thrown away without being executed. MC9S08JM60 Series Data Sheet, Rev. 5 336 Freescale Semiconductor

Development Support A force-type breakpoint waits for the current instruction to finish and then acts upon the breakpoint request. The usual action in response to a breakpoint is to go to active background mode rather than continuing to the next instruction in the user application program. The tag vs. force terminology is used in two contexts within the debug module. The first context refers to breakpoint requests from the debug module to the CPU. The second refers to match signals from the comparators to the debugger control logic. When a tag-type break request is sent to the CPU, a signal is entered into the instruction queue along with the opcode so that if/when this opcode ever executes, the CPU will effectively replace the tagged opcode with a BGND opcode so the CPU goes to active background mode rather than executing the tagged instruction. When the TRGSEL control bit in the DBGT register is set to select tag-type operation, the output from comparator A or B is qualified by a block of logic in the debug module that tracks opcodes and only produces a trigger to the debugger if the opcode at the compare address is actually executed. There is separate opcode tracking logic for each comparator so more than one compare event can be tracked through the instruction queue at a time. 18.3.5 Trigger Modes The trigger mode controls the overall behavior of a debug run. The 4-bit TRG field in the DBGT register selects one of nine trigger modes. When TRGSEL= 1 in the DBGT register, the output of the comparator must propagate through an opcode tracking circuit before triggering FIFO actions. The BEGIN bit in DBGT chooses whether the FIFO begins storing data when the qualified trigger is detected (begin trace), or the FIFO stores data in a circular fashion from the time it is armed until the qualified trigger is detected (end trigger). A debug run is started by writing a 1 to the ARM bit in the DBGC register, which sets the ARMF flag and clears the AF and BF flags and the CNT bits in DBGS. A begin-trace debug run ends when the FIFO gets full. An end-trace run ends when the selected trigger event occurs. Any debug run can be stopped manually by writing a 0 to ARM or DBGEN in DBGC. In all trigger modes except event-only modes, the FIFO stores change-of-flow addresses. In event-only trigger modes, the FIFO stores data in the low-order eight bits of the FIFO. The BEGIN control bit is ignored in event-only trigger modes and all such debug runs are begin type traces. When TRGSEL= 1 to select opcode fetch triggers, it is not necessary to use R/W in comparisons because opcode tags would only apply to opcode fetches that are always read cycles. It would also be unusual to specify TRGSEL =1 while using a full mode trigger because the opcode value is normally known at a particular address. The following trigger mode descriptions only state the primary comparator conditions that lead to a trigger. Either comparator can usually be further qualified with R/W by setting RWAEN (RWBEN) and the corresponding RWA (RWB) value to be matched against R/W. The signal from the comparator with optional R/W qualification is used to request a CPU breakpoint if BRKEN =1 and TAG determines whether the CPU request will be a tag request or a force request. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 337

Development Support A-Only — Trigger when the address matches the value in comparator A A OR B — Trigger when the address matches either the value in comparator A or the value in comparatorB A Then B — Trigger when the address matches the value in comparator B but only after the address for another cycle matched the value in comparator A. There can be any number of cycles after the A match and before the B match. A AND B Data (Full Mode) — This is called a full mode because address, data, and R/W (optionally) must match within the same bus cycle to cause a trigger event. Comparator A checks address, the low byte of comparator B checks data, and R/W is checked against RWA if RWAEN= 1. The high-order half of comparator B is not used. In full trigger modes it is not useful to specify a tag-type CPU breakpoint (BRKEN= TAG= 1), but if you do, the comparator B data match is ignored for the purpose of issuing the tag request to the CPU and the CPU breakpoint is issued when the comparator A address matches. A AND NOT B Data (Full Mode) — Address must match comparator A, data must not match the low half of comparator B, and R/W must match RWA if RWAEN= 1. All three conditions must be met within the same bus cycle to cause a trigger. In full trigger modes it is not useful to specify a tag-type CPU breakpoint (BRKEN= TAG= 1), but if you do, the comparator B data match is ignored for the purpose of issuing the tag request to the CPU and the CPU breakpoint is issued when the comparator A address matches. Event-Only B (Store Data) — Trigger events occur each time the address matches the value in comparator B. Trigger events cause the data to be captured into the FIFO. The debug run ends when the FIFO becomes full. A Then Event-Only B (Store Data) — After the address has matched the value in comparator A, a trigger event occurs each time the address matches the value in comparator B. Trigger events cause the data to be captured into the FIFO. The debug run ends when the FIFO becomes full. Inside Range (A ≤ Address ≤ B) — A trigger occurs when the address is greater than or equal to the value in comparator A and less than or equal to the value in comparator B at the same time. Outside Range (Address < A or Address > B) — A trigger occurs when the address is either less than the value in comparator A or greater than the value in comparator B. MC9S08JM60 Series Data Sheet, Rev. 5 338 Freescale Semiconductor

Development Support 18.3.6 Hardware Breakpoints The BRKEN control bit in the DBGC register may be set to 1 to allow any of the trigger conditions described in Section18.3.5, “Trigger Modes,” to be used to generate a hardware breakpoint request to the CPU. TAG in DBGC controls whether the breakpoint request will be treated as a tag-type breakpoint or a force-type breakpoint. A tag breakpoint causes the current opcode to be marked as it enters the instruction queue. If a tagged opcode reaches the end of the pipe, the CPU executes a BGND instruction to go to active background mode rather than executing the tagged opcode. A force-type breakpoint causes the CPU to finish the current instruction and then go to active background mode. If the background mode has not been enabled (ENBDM= 1) by a serial WRITE_CONTROL command through the BKGD pin, the CPU will execute an SWI instruction instead of going to active background mode. 18.4 Register Definition This section contains the descriptions of the BDC and DBG registers and control bits. Refer to the high-page register summary in the device overview chapter of this data sheet for the absolute address assignments for all DBG registers. This section refers to registers and control bits only by their names. A Freescale-provided equate or header file is used to translate these names into the appropriate absolute addresses. 18.4.1 BDC Registers and Control Bits The BDC has two registers: • The BDC status and control register (BDCSCR) is an 8-bit register containing control and status bits for the background debug controller. • The BDC breakpoint match register (BDCBKPT) holds a 16-bit breakpoint match address. These registers are accessed with dedicated serial BDC commands and are not located in the memory space of the target MCU (so they do not have addresses and cannot be accessed by user programs). Some of the bits in the BDCSCR have write limitations; otherwise, these registers may be read or written at any time. For example, the ENBDM control bit may not be written while the MCU is in active background mode. (This prevents the ambiguous condition of the control bit forbidding active background mode while the MCU is already in active background mode.) Also, the four status bits (BDMACT, WS, WSF, and DVF) are read-only status indicators and can never be written by the WRITE_CONTROL serial BDC command. The clock switch (CLKSW) control bit may be read or written at any time. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 339

Development Support 18.4.1.1 BDC Status and Control Register (BDCSCR) This register can be read or written by serial BDC commands (READ_STATUS and WRITE_CONTROL) but is not accessible to user programs because it is not located in the normal memory map of the MCU. 7 6 5 4 3 2 1 0 R BDMACT WS WSF DVF ENBDM BKPTEN FTS CLKSW W Normal 0 0 0 0 0 0 0 0 Reset Reset in 1 1 0 0 1 0 0 0 Active BDM: = Unimplemented or Reserved Figure18-5. BDC Status and Control Register (BDCSCR) Table18-2. BDCSCR Register Field Descriptions Field Description 7 Enable BDM (Permit Active Background Mode) — Typically, this bit is written to 1 by the debug host shortly ENBDM after the beginning of a debug session or whenever the debug host resets the target and remains 1 until a normal reset clears it. 0 BDM cannot be made active (non-intrusive commands still allowed) 1 BDM can be made active to allow active background mode commands 6 Background Mode Active Status — This is a read-only status bit. BDMACT 0 BDM not active (user application program running) 1 BDM active and waiting for serial commands 5 BDC Breakpoint Enable — If this bit is clear, the BDC breakpoint is disabled and the FTS (force tag select) BKPTEN control bit and BDCBKPT match register are ignored. 0 BDC breakpoint disabled 1 BDC breakpoint enabled 4 Force/Tag Select — When FTS=1, a breakpoint is requested whenever the CPU address bus matches the FTS BDCBKPT match register. When FTS=0, a match between the CPU address bus and the BDCBKPT register causes the fetched opcode to be tagged. If this tagged opcode ever reaches the end of the instruction queue, the CPU enters active background mode rather than executing the tagged opcode. 0 Tag opcode at breakpoint address and enter active background mode if CPU attempts to execute that instruction 1 Breakpoint match forces active background mode at next instruction boundary (address need not be an opcode) 3 Select Source for BDC Communications Clock — CLKSW defaults to 0, which selects the alternate BDC CLKSW clock source. 0 Alternate BDC clock source 1 MCU bus clock MC9S08JM60 Series Data Sheet, Rev. 5 340 Freescale Semiconductor

Development Support Table18-2. BDCSCR Register Field Descriptions (continued) Field Description 2 Wait or Stop Status — When the target CPU is in wait or stop mode, most BDC commands cannot function. WS However, the BACKGROUND command can be used to force the target CPU out of wait or stop and into active background mode where all BDC commands work. Whenever the host forces the target MCU into active background mode, the host should issue a READ_STATUS command to check that BDMACT=1 before attempting other BDC commands. 0 Target CPU is running user application code or in active background mode (was not in wait or stop mode when background became active) 1 Target CPU is in wait or stop mode, or a BACKGROUND command was used to change from wait or stop to active background mode 1 Wait or Stop Failure Status — This status bit is set if a memory access command failed due to the target CPU WSF executing a wait or stop instruction at or about the same time. The usual recovery strategy is to issue a BACKGROUND command to get out of wait or stop mode into active background mode, repeat the command that failed, then return to the user program. (Typically, the host would restore CPU registers and stack values and re-execute the wait or stop instruction.) 0 Memory access did not conflict with a wait or stop instruction 1 Memory access command failed because the CPU entered wait or stop mode 0 Data Valid Failure Status — This status bit is not used in the MC9S08JM60 Series because it does not have DVF any slow access memory. 0 Memory access did not conflict with a slow memory access 1 Memory access command failed because CPU was not finished with a slow memory access 18.4.1.2 BDC Breakpoint Match Register (BDCBKPT) This 16-bit register holds the address for the hardware breakpoint in the BDC. The BKPTEN and FTS control bits in BDCSCR are used to enable and configure the breakpoint logic. Dedicated serial BDC commands (READ_BKPT and WRITE_BKPT) are used to read and write the BDCBKPT register but is not accessible to user programs because it is not located in the normal memory map of the MCU. Breakpoints are normally set while the target MCU is in active background mode before running the user application program. For additional information about setup and use of the hardware breakpoint logic in the BDC, refer to Section18.2.4, “BDC Hardware Breakpoint.” 18.4.2 System Background Debug Force Reset Register (SBDFR) This register contains a single write-only control bit. A serial background mode command such as WRITE_BYTE must be used to write to SBDFR. Attempts to write this register from a user program are ignored. Reads always return 0x00. 7 6 5 4 3 2 1 0 R 0 0 0 0 0 0 0 0 W BDFR1 Reset 0 0 0 0 0 0 0 0 = Unimplemented or Reserved 1 BDFR is writable only through serial background mode debug commands, not from user programs. Figure18-6. System Background Debug Force Reset Register (SBDFR) MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 341

Development Support Table18-3. SBDFR Register Field Description Field Description 0 Background Debug Force Reset — A serial active background mode command such as WRITE_BYTE allows BDFR an external debug host to force a target system reset. Writing 1 to this bit forces an MCU reset. This bit cannot be written from a user program. 18.4.3 DBG Registers and Control Bits The debug module includes nine bytes of register space for three 16-bit registers and three 8-bit control and status registers. These registers are located in the high register space of the normal memory map so they are accessible to normal application programs. These registers are rarely if ever accessed by normal user application programs with the possible exception of a ROM patching mechanism that uses the breakpoint logic. 18.4.3.1 Debug Comparator A High Register (DBGCAH) This register contains compare value bits for the high-order eight bits of comparator A. This register is forced to 0x00 at reset and can be read at any time or written at any time unless ARM = 1. 18.4.3.2 Debug Comparator A Low Register (DBGCAL) This register contains compare value bits for the low-order eight bits of comparator A. This register is forced to 0x00 at reset and can be read at any time or written at any time unless ARM = 1. 18.4.3.3 Debug Comparator B High Register (DBGCBH) This register contains compare value bits for the high-order eight bits of comparator B. This register is forced to 0x00 at reset and can be read at any time or written at any time unless ARM = 1. 18.4.3.4 Debug Comparator B Low Register (DBGCBL) This register contains compare value bits for the low-order eight bits of comparator B. This register is forced to 0x00 at reset and can be read at any time or written at any time unless ARM = 1. 18.4.3.5 Debug FIFO High Register (DBGFH) This register provides read-only access to the high-order eight bits of the FIFO. Writes to this register have no meaning or effect. In the event-only trigger modes, the FIFO only stores data into the low-order byte of each FIFO word, so this register is not used and will read 0x00. Reading DBGFH does not cause the FIFO to shift to the next word. When reading 16-bit words out of the FIFO, read DBGFH before reading DBGFL because reading DBGFL causes the FIFO to advance to the next word of information. MC9S08JM60 Series Data Sheet, Rev. 5 342 Freescale Semiconductor

Development Support 18.4.3.6 Debug FIFO Low Register (DBGFL) This register provides read-only access to the low-order eight bits of the FIFO. Writes to this register have no meaning or effect. Reading DBGFL causes the FIFO to shift to the next available word of information. When the debug module is operating in event-only modes, only 8-bit data is stored into the FIFO (high-order half of each FIFO word is unused). When reading 8-bit words out of the FIFO, simply read DBGFL repeatedly to get successive bytes of data from the FIFO. It isn’t necessary to read DBGFH in this case. Do not attempt to read data from the FIFO while it is still armed (after arming but before the FIFO is filled or ARMF is cleared) because the FIFO is prevented from advancing during reads of DBGFL. This can interfere with normal sequencing of reads from the FIFO. Reading DBGFL while the debugger is not armed causes the address of the most-recently fetched opcode to be stored to the last location in the FIFO. By reading DBGFH then DBGFL periodically, external host software can develop a profile of program execution. After eight reads from the FIFO, the ninth read will return the information that was stored as a result of the first read. To use the profiling feature, read the FIFO eight times without using the data to prime the sequence and then begin using the data to get a delayed picture of what addresses were being executed. The information stored into the FIFO on reads of DBGFL (while the FIFO is not armed) is the address of the most-recently fetched opcode. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 343

Development Support 18.4.3.7 Debug Control Register (DBGC) This register can be read or written at any time. 7 6 5 4 3 2 1 0 R DBGEN ARM TAG BRKEN RWA RWAEN RWB RWBEN W Reset 0 0 0 0 0 0 0 0 Figure18-7. Debug Control Register (DBGC) Table18-4. DBGC Register Field Descriptions Field Description 7 Debug Module Enable — Used to enable the debug module. DBGEN cannot be set to 1 if the MCU is secure. DBGEN 0 DBG disabled 1 DBG enabled 6 Arm Control — Controls whether the debugger is comparing and storing information in the FIFO. A write is used ARM to set this bit (and ARMF) and completion of a debug run automatically clears it. Any debug run can be manually stopped by writing 0 to ARM or to DBGEN. 0 Debugger not armed 1 Debugger armed 5 Tag/Force Select — Controls whether break requests to the CPU will be tag or force type requests. If TAG BRKEN=0, this bit has no meaning or effect. 0 CPU breaks requested as force type requests 1 CPU breaks requested as tag type requests 4 Break Enable — Controls whether a trigger event will generate a break request to the CPU. Trigger events can BRKEN cause information to be stored in the FIFO without generating a break request to the CPU. For an end trace, CPU break requests are issued to the CPU when the comparator(s) and R/W meet the trigger requirements. For a begin trace, CPU break requests are issued when the FIFO becomes full. TRGSEL does not affect the timing of CPU break requests. 0 CPU break requests not enabled 1 Triggers cause a break request to the CPU 3 R/W Comparison Value for Comparator A — When RWAEN=1, this bit determines whether a read or a write RWA access qualifies comparator A. When RWAEN=0, RWA and the R/W signal do not affect comparator A. 0 Comparator A can only match on a write cycle 1 Comparator A can only match on a read cycle 2 Enable R/W for Comparator A — Controls whether the level of R/W is considered for a comparator A match. RWAEN 0 R/W is not used in comparison A 1 R/W is used in comparison A 1 R/W Comparison Value for Comparator B — When RWBEN=1, this bit determines whether a read or a write RWB access qualifies comparator B. When RWBEN=0, RWB and the R/W signal do not affect comparator B. 0 Comparator B can match only on a write cycle 1 Comparator B can match only on a read cycle 0 Enable R/W for Comparator B — Controls whether the level of R/W is considered for a comparator B match. RWBEN 0 R/W is not used in comparison B 1 R/W is used in comparison B MC9S08JM60 Series Data Sheet, Rev. 5 344 Freescale Semiconductor

Development Support 18.4.3.8 Debug Trigger Register (DBGT) This register can be read any time, but may be written only if ARM =0, except bits 4 and 5 are hard-wired to 0s. 7 6 5 4 3 2 1 0 R 0 0 TRGSEL BEGIN TRG3 TRG2 TRG1 TRG0 W Reset 0 0 0 0 0 0 0 0 = Unimplemented or Reserved Figure18-8. Debug Trigger Register (DBGT) Table18-5. DBGT Register Field Descriptions Field Description 7 Trigger Type — Controls whether the match outputs from comparators A and B are qualified with the opcode TRGSEL tracking logic in the debug module. If TRGSEL is set, a match signal from comparator A or B must propagate through the opcode tracking logic and a trigger event is only signalled to the FIFO logic if the opcode at the match address is actually executed. 0 Trigger on access to compare address (force) 1 Trigger if opcode at compare address is executed (tag) 6 Begin/End Trigger Select — Controls whether the FIFO starts filling at a trigger or fills in a circular manner until BEGIN a trigger ends the capture of information. In event-only trigger modes, this bit is ignored and all debug runs are assumed to be begin traces. 0 Data stored in FIFO until trigger (end trace) 1 Trigger initiates data storage (begin trace) 3:0 Select Trigger Mode — Selects one of nine triggering modes, as described below. TRG[3:0] 0000 A-only 0001 A OR B 0010 A Then B 0011 Event-only B (store data) 0100 A then event-only B (store data) 0101 A AND B data (full mode) 0110 A AND NOT B data (full mode) 0111 Inside range: A ≤ address ≤ B 1000 Outside range: address < A or address > B 1001 – 1111 (No trigger) MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 345

Development Support 18.4.3.9 Debug Status Register (DBGS) This is a read-only status register. 7 6 5 4 3 2 1 0 R AF BF ARMF 0 CNT3 CNT2 CNT1 CNT0 W Reset 0 0 0 0 0 0 0 0 = Unimplemented or Reserved Figure18-9. Debug Status Register (DBGS) Table18-6. DBGS Register Field Descriptions Field Description 7 Trigger Match A Flag — AF is cleared at the start of a debug run and indicates whether a trigger match A AF condition was met since arming. 0 Comparator A has not matched 1 Comparator A match 6 Trigger Match B Flag — BF is cleared at the start of a debug run and indicates whether a trigger match B BF condition was met since arming. 0 Comparator B has not matched 1 Comparator B match 5 Arm Flag — While DBGEN=1, this status bit is a read-only image of ARM in DBGC. This bit is set by writing 1 ARMF to the ARM control bit in DBGC (while DBGEN=1) and is automatically cleared at the end of a debug run. A debug run is completed when the FIFO is full (begin trace) or when a trigger event is detected (end trace). A debug run can also be ended manually by writing 0 to ARM or DBGEN in DBGC. 0 Debugger not armed 1 Debugger armed 3:0 FIFO Valid Count — These bits are cleared at the start of a debug run and indicate the number of words of valid CNT[3:0] data in the FIFO at the end of a debug run. The value in CNT does not decrement as data is read out of the FIFO. The external debug host is responsible for keeping track of the count as information is read out of the FIFO. 0000 Number of valid words in FIFO = No valid data 0001 Number of valid words in FIFO = 1 0010 Number of valid words in FIFO = 2 0011 Number of valid words in FIFO = 3 0100 Number of valid words in FIFO = 4 0101 Number of valid words in FIFO = 5 0110 Number of valid words in FIFO = 6 0111 Number of valid words in FIFO = 7 1000 Number of valid words in FIFO = 8 MC9S08JM60 Series Data Sheet, Rev. 5 346 Freescale Semiconductor

Appendix A Electrical Characteristics A.1 Introduction This appendix contains electrical and timing specifications for the MC9S08JM60 series of microcontrollers available at the time of publication. A.2 Parameter Classification The electrical parameters shown in this supplement are guaranteed by various methods. To give the customer a better understanding the following classification is used and the parameters are tagged accordingly in the tables where appropriate: TableA-1. Parameter Classifications P Those parameters are guaranteed during production testing on each individual device. Those parameters are achieved by the design characterization by measuring a statistically relevant C sample size across process variations. Those parameters are achieved by design characterization on a small sample size from typical devices T under typical conditions unless otherwise noted. All values shown in the typical column are within this category. D Those parameters are derived mainly from simulations. NOTE The classification is shown in the column labeled “C” in the parameter tables where appropriate. A.3 Absolute Maximum Ratings Absolute maximum ratings are stress ratings only, and functional operation at the maxima is not guaranteed. Stress beyond the limits specified in Table A-2 may affect device reliability or cause permanent damage to the device. For functional operating conditions, refer to the remaining tables in this section. This device contains circuitry protecting against damage due to high static voltage or electrical fields; however, it is advised that normal precautions be taken to avoid application of any voltages higher than maximum-rated voltages to this high-impedance circuit. Reliability of operation is enhanced if unused inputs are tied to an appropriate logic voltage level (for instance, either V or V ). SS DD MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 347

AppendixA Electrical Characteristics TableA-2. Absolute Maximum Ratings Rating Symbol Value Unit Supply voltage V – 0.3 to + 5.8 V DD Input voltage V – 0.3 to V + 0.3 V In DD Instantaneous maximum current I ± 25 mA Single pin limit (applies to all port pins)1,2,3 D Maximum current into V I 120 mA DD DD Storage temperature Tstg –55 to +150 °C 1 Input must be current limited to the value specified. To determine the value of the required current-limiting resistor, calculate resistance values for positive (V ) and negative (V ) clamp DD SS voltages, then use the larger of the two resistance values. 2 All functional non-supply pins are internally clamped to V and V . SS DD 3 Power supply must maintain regulation within operating V range during instantaneous and DD operating maximum current conditions. If positive injection current (V > V ) is greater than In DD I , the injection current may flow out of V and could result in external power supply going DD DD out of regulation. Ensure external V load will shunt current greater than maximum injection DD current. This will be the greatest risk when the MCU is not consuming power. Examples are: if no system clock is present, or if the clock rate is very low which would reduce overall power consumption. A.4 Thermal Characteristics This section provides information about operating temperature range, power dissipation, and package thermal resistance. Power dissipation on I/O pins is usually small compared to the power dissipation in on-chip logic and it is user-determined rather than being controlled by the MCU design. In order to take P into account in power calculations, determine the difference between actual pin voltage and V or I/O SS V and multiply by the pin current for each I/O pin. Except in cases of unusually high pin current (heavy DD loads), the difference between pin voltage and V or V will be very small. SS DD TableA-3. Thermal Characteristics Temp. Num C Rating Symbol Value Unit Code 1 T Operating temperature range (packaged) T –40 to 85 °C C A 2 D Maximum junction temperature T 135 °C J Thermal resistance Single layer board 64-pin QFP 55 64-pin LQFP 73 48-pin QFN 84 3 T 44-pin LQFP θ 71 °C/W — JA Four layer board 64-pin QFP 41 64-pin LQFP 54 48-pin QFN 28 44-pin LQFP 49 MC9S08JM60 Series Data Sheet, Rev. 5 348 Freescale Semiconductor

AppendixA Electrical Characteristics The average chip-junction temperature (T ) in °C can be obtained from: J T = T + (P × θ ) Eqn.A-1 J A D JA where: T = Ambient temperature, °C A θ = Package thermal resistance, junction-to-ambient, °C/W JA P = P + P D int I/O P = I × V , Watts — chip internal power int DD DD P = Power dissipation on input and output pins — user determined I/O For most applications, P << P and can be neglected. An approximate relationship between P and T I/O int D J (if P is neglected) is: I/O P = K ÷ (T + 273°C) Eqn.A-2 D J Solving equations 1 and 2 for K gives: K = P × (T + 273°C) + θ × (P )2 Eqn.A-3 D A JA D where K is a constant pertaining to the particular part. K can be determined from equation 3 by measuring P (at equilibrium) for a known T . Using this value of K, the values of P and T can be obtained by D A D J solving equations 1 and 2 iteratively for any value of T . A A.5 ESD Protection and Latch-Up Immunity Although damage from electrostatic discharge (ESD) is much less common on these devices than on early CMOS circuits, normal handling precautions must be used to avoid exposure to static discharge. Qualification tests are performed to ensure that these devices can withstand exposure to reasonable levels of static without suffering any permanent damage. All ESD testing is in conformity with AEC-Q100 Stress Test Qualification for Automotive Grade Integrated Circuits. During the device qualification ESD stresses were performed for the Human Body Model (HBM) and the Charge Device Model (CDM). A device is defined as a failure if after exposure to ESD pulses the device no longer meets the device specification. Complete DC parametric and functional testing is performed per the applicable device specification at room temperature followed by hot temperature, unless specified otherwise in the device specification. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 349

AppendixA Electrical Characteristics TableA-4. ESD and Latch-up Test Conditions Model Description Symbol Value Unit Series Resistance R1 1500 Ω Human Body Storage Capacitance C 100 pF Number of Pulse per pin — 3 Minimum input voltage limit –2.5 V Latch-up Maximum input voltage limit 7.5 V TableA-5. ESD and Latch-Up Protection Characteristics Num Rating Symbol Min Max Unit 1 Human Body Model (HBM) V ±2000 — V HBM 2 Charge Device Model (CDM) V ±500 — V CDM 3 Latch-up Current at T = 85°C I ±100 — mA A LAT A.6 DC Characteristics This section includes information about power supply requirements, I/O pin characteristics, and power supply current in various operating modes. TableA-6. DC Characteristics Num C Parameter Symbol Min Typical1 Max. Unit 1 Operating voltage2 2.7 — 5.5 V Output high voltage — Low drive (PTxDSn = 0) 5 V, I = –4 mA V – 1.5 — — Load DD 3 V, I = –2 mA V – 1.5 — — Load DD 5 V, I = –2 mA V – 0.8 — — Load DD 3 V, I = –1 mA V – 0.8 — — Load DD V 2 P OH V Output high voltage — High drive (PTxDSn = 1) 5 V, I = –15 mA V – 1.5 — — Load DD 3 V, I = –8 mA V – 1.5 — — Load DD 5 V, I = –8 mA V – 0.8 — — Load DD 3 V, I = –4 mA V – 0.8 — — Load DD Output low voltage — Low drive (PTxDSn = 0) 5 V, I = 4 mA — — 1.5 Load 3 V, I = 2 mA — — 1.5 Load 5 V, I = 2 mA — — 0.8 Load 3 V, I = 1 mA — — 0.8 Load V 3 P OL V Output low voltage — High drive (PTxDSn = 1) 5 V, I = 15 mA — — 1.5 Load 3 V, I = 8 mA — — 1.5 Load 5 V, I = 8 mA — — 0.8 Load 3 V, I = 4 mA — — 0.8 Load 4 P Output high current — Max. total I for all ports OH 5 V I — — 100 mA OHT 3 V — — 60 MC9S08JM60 Series Data Sheet, Rev. 5 350 Freescale Semiconductor

AppendixA Electrical Characteristics TableA-6. DC Characteristics (continued) Num C Parameter Symbol Min Typical1 Max. Unit 5 P Output low current — Max. total I for all ports OL 5 V I — — 100 mA OLT 3 V — — 60 6 C Input high voltage; all digital inputs 5 V V 0.65 × V — — IH DD V 3 V 0.70 × V DD 7 C Input low voltage; all digital inputs V — — 0.35 × V IL DD 8 C Input hysteresis; all digital inputs V 0.06 × V mV hys DD 9 C Input leakage current (per pin); input only pins |I | — 0.1 1 μA In 10 P Hi-Z (off-state) leakage current (per pin) |I | — 0.1 1 μA OZ 11 P Internal pullup resistors3 R 20 45 65 kΩ PU 12 P Internal pulldown resistors4 R 20 45 65 kΩ PD 13 T Internal pullup resistor to USBDP (to V ) USB33 kΩ Idle R 900 1300 1575 PUPD Transmit 1425 2400 3090 14 D DC injection current5 6 7 8 (single pin limit) V >V 0 — 2 mA IN DD V <V 0 — –0.2 IN SS DC injection current (Total MCU limit, includes IIC sum of all stressed pins) mA V >V 0 — 25 IN DD V <V 0 — –5 IN SS 15 D Input capacitance; all non-supply pins C — — 8 pF In 16 D RAM retention voltage V — 0.6 1.0 V RAM 17 D POR re-arm voltage V 0.9 1.4 2.0 V POR 18 D POR re-arm time t 10 — — μs POR MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 351

AppendixA Electrical Characteristics TableA-6. DC Characteristics (continued) Num C Parameter Symbol Min Typical1 Max. Unit Low-voltage detection threshold — High range 19 P V V V falling LVD1 3.9 4.0 4.1 DD V rising 4.0 4.1 4.2 DD Low-voltage detection threshold — Low range 20 P V V V falling LVD0 2.48 2.56 2.64 DD V rising 2.54 2.62 2.70 DD Low-voltage warning threshold — High range 1 21 P V V V falling LVW3 4.5 4.6 4.7 DD V rising 4.6 4.7 4.8 DD Low-voltage warning threshold — High range 0 22 C V V V falling LVW2 4.2 4.3 4.4 DD V rising 4.3 4.4 4.5 DD Low-voltage warning threshold Low range 1 23 P V V V falling LVW1 2.84 2.92 3.00 DD V rising 2.90 2.98 3.06 DD Low-voltage warning threshold — Low range 0 24 C V V V falling LVW0 2.66 2.74 2.82 DD V rising 2.72 2.80 2.88 DD Low-voltage inhibit reset/recover hysteresis 25 T +5V V — 100 — mV hys +3V — 60 — mV Bandgap voltage reference 26 P V 1.19 1.20 1.21 V factory trimmed at V = 5.0 V, Temp = 25°C BG DD 1 Typical values are based on characterization data at 25°C unless otherwise stated. 2 Maximum is highest voltage that POR is guaranteed. 3 Measured with V = V . In SS 4 Measured with V = V . In DD 5 Power supply must maintain regulation within operating VDD range during instantaneous and operating maximum current conditions. If positive injection current (VIn > VDD) is greater than IDD, the injection current may flow out of VDD and could result in external power supply going out of regulation. Ensure external VDD load will shunt current greater than maximum injection current. This will be the greatest risk when the MCU is not consuming power. Examples are: if no system clock is present, or if clock rate is very low (which would reduce overall power consumption). 6 All functional non-supply pins are internally clamped to VSS and VDD. 7 Input must be current limited to the value specified. To determine the value of the required current-limiting resistor, calculate resistance values for positive and negative clamp voltages, then use the larger of the two values. 8 The RESET pin does not have a clamp diode to V . Do not drive this pin above V . DD DD MC9S08JM60 Series Data Sheet, Rev. 5 352 Freescale Semiconductor

AppendixA Electrical Characteristics Typical VOL vs. IOL AT VDD = 5V Typical VOL vs. IOL AT VDD = 3V 0.7 Hot (85°C) 1.4 Hot (85°C) 0.6 Room (25°C) 1.2 Room (25°C) Cold (-40°C) 0.5 1.0 Cold (-40°C) V(v)OL 00..34 V (v)OL 00..68 0.2 0.4 0.1 0.2 0.0 0.0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 0.0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 IOL (mA) IOL (mA) FigureA-1. Typical Low-side Drive (sink) characteristics – High Drive (PTxDSn = 1) Typical VOL vs. IOL AT VDD = 5V Typical VOL vs. IOL AT VDD = 3V 0.8 Hot (85°C) Hot (85°C) 0.7 Room (25°C) 0.8 0.6 Cold (-40°C) 0.7 Room (25°C) 0.6 0.5 Cold (-40°C) V (v)OL 00..34 V (v)OL000...345 0.2 0.2 0.1 0.1 0.0 0.0 0 1 2 3 0 1 2 3 4 5 I (mA) IOL (mA) OL FigureA-2. Typical Low-side Drive (sink) characteristics – Low Drive (PTxDSn = 0) Typical VDD - VOH vs. IOH AT VDD = 5V Typical VDD - VOH vs. IOH AT VDD = 3V 1.2 0.8 Hot (85°C) Hot (85°C) 1.0 Room (25°C) V - V (v)DDOH000...246 RCoooldm ( -4(205°°CC)) - V (v)DDOH 000...468 Cold (-40°C) V 0.2 0.0 0 -1 -2 -3 -4 -5 -6 -7 -8 -9 -10-11-12-13-14-15 0.0 0 -1 -2 -3 -4 -5 -6 -7 -8 -9 -10-11-12-13-14-15 IOH (mA) I (mA) OH FigureA-3. Typical High-side Drive (source) characteristics – High Drive (PTxDSn = 1) MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 353

AppendixA Electrical Characteristics Typical VDD - VOH vs. IOH AT VDD = 5V Typical VDD - VOH vs. IOH AT VDD = 3V 1.2 1.2 Hot (85°C) Hot (85°C) 1.0 1.0 Room (25°C) V - V (v)DDOH 000...468 RCoooldm ( -(4205°°CC)) V - V (v)DDOH 000...468 Cold (-40°C) 0.2 0.2 0.0 0.0 0 -1 -2 -3 -4 -5 0 -1 -2 -3 IOH (mA) IOH (mA) FigureA-4. Typical High-side Drive (source) characteristics – Low Drive (PTxDSn = 0) MC9S08JM60 Series Data Sheet, Rev. 5 354 Freescale Semiconductor

AppendixA Electrical Characteristics A.7 Supply Current Characteristics TableA-7. Supply Current Characteristics Num C Parameter Symbol V (V) Typical1 Max2 Unit DD Run supply current3 measured at 5 1.1 1.6 1 C (Core clock = 2MHz, f = 1 MHz, BLPE mode) mA Bus 3 0.8 1.5 Run supply current3 measured at 5 4.9 8 RI 2 P (Core clock = 8MHz, f = 4 MHz, FBE mode) DD mA Bus 3 4.3 7 Run supply current3 measured at 5 23 30 3 C (Core clock = 48MHz, f = 24 MHz, PEE mode) mA Bus 3 22 30 Stop2 mode supply current –40 °C 3 5 0.80 μA 25 °C 3 85 °C 20 4 P S2I DD 3 –40 °C 25 °C 3 0.80 3 μA 20 85 °C Stop3 mode supply current –40 °C 3 5 0.90 μA 25 °C 3 85 °C 20 5 P S3I DD 3 –40 °C 25 °C 3 0.90 3 μA 20 85 °C Adder to stop2 or stop3 for RTC enabled4, 25°C 5 300 nA 6 P ΔI SRTC 3 300 nA Adder to stop3 for LVD enabled 5 110 μA 7 P (LVDE = LVDSE = 1) ΔISLVD 3 90 μA Adder to stop3 for oscillator enabled5 5 5 μA 8 P (ERCLKEN = 1 and EREFSTEN = 1) ΔISOSC 3 5 μA 9 T USB module enable current6 ΔI 5 1.5 mA USBE 10 T USB suspend current7 I 5 270 500 μA SUSP 1 Typicals are measured at 25°C. 2 Values given here are preliminary estimates prior to completing characterization. 3 All modules except USB and ADC active, Oscillator disabled (ERCLKEN = 0), using external clock resource for input, and does not include any dc loads on port pins. 4 Most customers are expected to find that auto-wakeup from stop2 or stop3 can be used instead of the higher current wait mode. Wait mode typical is 560 μA at 5 V and 422 μA at 3V with f = 1 MHz. Bus 5 Values given under the following conditions: low range operation (RANGE = 0), low power mode (HGO = 0). MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 355

AppendixA Electrical Characteristics 6 Here USB module is enabled and clocked at 48 MHz (USBEN = 1, USBVREN =1, USBPHYEN = 1 and USBPU = 1), and D+ and D– pull down by two 15.1kΩ resisters independently. The current consumption may be much higher when the packets are being transmitted through the attached cable. 7 MCU enters into Stop3 mode, USB bus in idle state. The USB suspend current will be dominated by the D+ pull up resister. A.8 Analog Comparator (ACMP) Electricals TableA-8. Analog Comparator Electrical Specifications Num C Rating Symbol Min Typical Max Unit 1 — Supply voltage V 2.7 — 5.5 V DD 2 D Supply current (active) I — 20 35 μA DDAC 3 D Analog input voltage V V – 0.3 — V V AIN SS DD 4 D Analog input offset voltage V 20 40 mV AIO 5 D Analog Comparator hysteresis V 3.0 6.0 20.0 mV H 6 D Analog input leakage current I 1.0 μA ALKG 7 D Analog Comparator initialization delay t — — 1.0 μs AINIT A.9 ADC Characteristics TableA-9. 5 Volt 12-bit ADC Operating Conditions Characteristic Conditions Symb Min Typ1 Max Unit Comment Absolute V 2.7 — 5.5 V DDAD Supply voltage Delta to V (V -V )2 ΔV –100 0 +100 mV DD DD DDAD DDAD Ground voltage Delta to V (V -V )2 ΔV –100 0 +100 mV SS SS SSAD SSAD Ref Voltage V 2.7 V V V High REFH DDAD DDAD Ref Voltage V V V V V Low REFL SSAD SSAD SSAD Input Voltage V V — V V ADIN REFL REFH Input C — 4.5 5.5 pF Capacitance ADIN Input R — 3 5 kΩ Resistance ADIN 12 bit mode f > 4 MHz — — 2 ADCK f < 4 MHz — — 5 ADCK Analog Source 10 bit mode R kΩ External to MCU Resistance AS f > 4 MHz — — 5 ADCK f < 4 MHz — — 10 ADCK 8 bit mode (all valid f ) — — 10 ADCK MC9S08JM60 Series Data Sheet, Rev. 5 356 Freescale Semiconductor

AppendixA Electrical Characteristics TableA-9. 5 Volt 12-bit ADC Operating Conditions (continued) Characteristic Conditions Symb Min Typ1 Max Unit Comment ADC High Speed (ADLPC=0) 0.4 — 8.0 Conversion f MHz ADCK Clock Freq. Low Power (ADLPC=1) 0.4 — 4.0 1 Typical values assume V = 5.0 V, Temp = 25°C, f = 1.0 MHz unless otherwise stated. Typical values are for DDAD ADCK reference only and are not tested in production. 2 DC potential difference. SIMPLIFIED INPUT PIN EQUIVALENT CIRCUIT ZADIN SIMPLIFIED Pad ZAS leakage CHANNEL SELECT due to CIRCUIT ADC SAR R input R ENGINE AS protection ADIN + V ADIN – C V + AS AS – R ADIN INPUT PIN R ADIN INPUT PIN R ADIN INPUT PIN C ADIN FigureA-5. ADC Input Impedance Equivalency Diagram MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 357

AppendixA Electrical Characteristics TableA-10. 5 Volt 12-bit ADC Characteristics (V = V , V = V ) REFH DDAD REFL SSAD Characteristic Conditions C Symb Min Typ1 Max Unit Comment Supply Current ADLPC=1 T I — 133 — μA ADLSMP=1 DDAD ADCO=1 Supply Current ADLPC=1 T I — 218 — μA ADLSMP=0 DDAD ADCO=1 Supply Current ADLPC=0 T I — 327 — μA ADLSMP=1 DDAD ADCO=1 Supply Current ADLPC=0 T I — 0.582 1 mA ADLSMP=0 DDAD ADCO=1 Supply Current Stop, Reset, Module Off I — 0.011 1 μA DDAD ADC High Speed (ADLPC=0) 2 3.3 5 t = Asynchronous T f MHz ADACK ADACK 1/f Clock Source Low Power (ADLPC=1) 1.25 2 3.3 ADACK Conversion Short Sample (ADLSMP=0) — 20 — ADCK Time (Including T tADC cycles See Table sample time) Long Sample (ADLSMP=1) — 40 — 10.13 for conversion Short Sample (ADLSMP=0) — 3.5 — Sample Time T t ADCK time variances ADS cycles Long Sample (ADLSMP=1) — 23.5 — 12 bit mode T — ±3.0 ±10.0 Total Includes Unadjusted 10 bit mode P E — ±1 ±2.5 LSB2 TUE quantization Error 8 bit mode T — ±0.5 ±1.0 12 bit mode T — ±1.75 ±4.0 Differential 10 bit mode3 P DNL — ±0.5 ±1.0 LSB2 Non-Linearity 8 bit mode2 T — ±0.3 ±0.5 12 bit mode T — ±1.5 ±4.0 Integral 10 bit mode T INL — ±0.5 ±1.0 LSB2 Non-Linearity 8 bit mode T — ±0.3 ±0.5 12 bit mode T — ±1.5 ±6.0 Zero-Scale 10 bit mode P E — ±0.5 ±1.5 LSB2 V = V Error ZS ADIN SSAD 8 bit mode T — ±0.5 ±0.5 MC9S08JM60 Series Data Sheet, Rev. 5 358 Freescale Semiconductor

AppendixA Electrical Characteristics TableA-10. 5 Volt 12-bit ADC Characteristics (V = V , V = V ) (continued) REFH DDAD REFL SSAD Characteristic Conditions C Symb Min Typ1 Max Unit Comment 12 bit mode T — ±1 ±4.0 Full-Scale 10 bit mode P E — ±0.5 ±1 LSB2 V = V Error FS ADIN DDAD 8 bit mode T — ±0.5 ±0.5 12 bit mode — –1 to 0 –1 to 0 Quantization 10 bit mode D E — — ±0.5 LSB2 Error Q 8 bit mode — — ±0.5 12 bit mode — ±1 ±10 Input Leakage Pad leakage4 * 10 bit mode D E — ±0.2 ±2.5 LSB2 Error IL R AS 8 bit mode — ±0.1 ±1 Temp Sensor 25°C D V — 1.396 — V Voltage TEMP25 –40 °C — 25 °C — 3.266 — Temp Sensor D m mV/°C Slope 25 °C — 125 °C — 3.638 — 1 Typical values assume V = 5.0 V, Temp = 25°C, f = 1.0 MHz unless otherwise stated. Typical values are for reference DDAD ADCK only and are not tested in production. 2 1 LSB = (V – V )/2N REFH REFL 3 Monotonicity and no-missing-codes guaranteed in 10 bit and 8 bit modes. 4 Based on input pad leakage current. Refer to pad electricals. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 359

AppendixA Electrical Characteristics A.10 External Oscillator (XOSC) Characteristics TableA-11. Oscillator Electrical Specifications (Temperature Range = –40 to 85°C Ambient) Num C Rating Symbol Min Typ1 Max Unit Oscillator crystal or resonator (EREFS=1, ERCLKEN = 1) Low range (RANGE = 0) f 32 — 38.4 kHz lo High range (RANGE = 1) FEE or FBE mode 2 f 1 — 5 MHz 1 C hi-fll High range (RANGE = 1) PEE or PBE mode 3 f 1 — 16 MHz hi-pll High range (RANGE = 1, HGO = 1) BLPE mode f 1 — 16 MHz hi-hgo High range (RANGE = 1, HGO = 0) BLPE mode f 1 — 8 MHz hi-lp See crystal or resonator 2 — Load capacitors C C 1, 2 manufacturer’s recommendation. Feedback resistor 3 — Low range (32 kHz to 38.4 kHz) R 10 MΩ F High range (1 MHz to 16 MHz) 1 MΩ Series resistor kΩ Low range, low gain (RANGE = 0, HGO = 0) — 0 — Low range, high gain (RANGE = 0, HGO = 1) — 100 — High range, low gain (RANGE = 1, HGO = 0) — 0 — 4 — R High range, high gain (RANGE = 1, HGO = 1) S ≥ 8 MHz — 0 0 4 MHz — 0 10 1 MHz — 0 20 Crystal start-up time 4 Low range, low gain (RANGE = 0, HGO = 0) t — 200 — ms CSTL-LP 5 T Low range, high gain (RANGE = 0, HGO = 1) t — 400 — CSTL-HGO High range, low gain (RANGE = 1, HGO = 0)5 t — 5 — CSTH-LP High range, high gain (RANGE = 1, HGO = 1)5 t — 15 — CSTH-HGO Square wave input clock frequency (EREFS=0, ERCLKEN = 1) FEE or FBE mode 2 0.03125 — 5 MHz 6 T f PEE or PBE mode 3 extal 1 — 16 MHz BLPE mode 0 — 40 MHz 1 Typical data was characterized at 3.0 V, 25°C or is recommended value. 2 When MCG is configured for FEE or FBE mode, input clock source must be divided using RDIV to within the range of 31.25 kHz to 39.0625 kHz. 3 When MCG is configured for PEE or PBE mode, input clock source must be divided using RDIV to within the range of 1 MHz to 2 MHz. 4 This parameter is characterized and not tested on each device. Proper PC board layout procedures must be followed to achieve specifications. 5 4 MHz crystal MCU EXTAL XTAL R R S F C1 Crystal or Resonator C2 MC9S08JM60 Series Data Sheet, Rev. 5 360 Freescale Semiconductor

AppendixA Electrical Characteristics A.11 MCG Specifications TableA-12. MCG Frequency Specifications(Temperature Range = –40 to 125°C Ambient) Num C Rating Symbol Min Typical Max Unit Internal reference frequency - factory trimmed at V = DD 1 P 5 V and temperature = 25 °C fint_ft — 31.25 — kHz 2 P Average internal reference frequency – untrimmed 1 fint_ut 25 32.7 41.66 kHz 3 P Average internal reference frequency Q – user trimmed fint_t 31.25 — 39.0625 kHz 4 D Internal reference startup time tirefst — 60 100 μs DCO output frequency range - untrimmed 1 5 — fdco_ut 25.6 33.48 42.66 MHz value provided for reference: f = 1024 X f dco_ut int_ut 6 P DCO output frequency range - trimmed fdco_t 32 — 40 MHz Resolution of trimmed DCO output frequency at fixed 7 C voltage and temperature (using FTRIM) Δfdco_res_t — ±0.1 ±0.2 %fdco Resolution of trimmed DCO output frequency at fixed 8 C voltage and temperature (not using FTRIM) Δfdco_res_t — ±0.2 ±0.4 %fdco Total deviation of trimmed DCO output frequency over +0.5 9 P voltage and temperature Δfdco_t — –1.0 ±2 %fdco Total deviation of trimmed DCO output frequency over 10 C fixed voltage and temperature range of 0 –70 °C Δfdco_t — ±0.5 ±1 %fdco 11 C FLL acquisition time 2 tfll_acquire — — 1 ms 12 D PLL acquisition time 3 tpll_acquire — — 1 ms Long term Jitter of DCO output clock (averaged over 13 C 2ms interval) 4 CJitter — 0.02 0.2 %fdco 14 D VCO operating frequency fvco 7.0 — 55.0 MHz 15 D PLL reference frequency range fpll_ref 1.0 — 2.0 MHz Long term accuracy of PLL output clock (averaged over 16 T 2 ms) fpll_jitter_2ms — 0.5905 — %fpll 17 T Jitter of PLL output clock measured over 625 ns fpll_jitter_625ns — 0.5665 — %fpll 18 D Lock entry frequency tolerance 6 Dlock ±1.49 — ±2.98 % 19 D Lock exit frequency tolerance 7 Dunl ±4.47 — ±5.97 % t 20 D Lock time – FLL tfll_lock — — fll_acqfuire+ s 1075(1/int_t) t 21 D Lock time – PLL tpll_lock — — pll_acfquire+ s 1075(1/pll_ref) 22 D Loss of external clock minimum frequency – RANGE = 0 floc_low (3/5) x fint — — kHz 23 D Loss of external clock minimum frequency – RANGE = 1 floc_high (16/5) x fint — — kHz 1 TRIM register at default value (0x80) and FTRIM control bit at default value (0x0). 2 This specification applies to any time the FLL reference source or reference divider is changed, trim value changed or changing from FLL disabled (BLPE, BLPI) to FLL enabled (FEI, FEE, FBE, FBI). If a crystal/resonator is being used as the reference, this specification assumes it is already running. 3 This specification applies to any time the PLL VCO divider or reference divider is changed, or changing from PLL disabled (BLPE, BLPI) to PLL enabled (PBE, PEE). If a crystal/resonator is being used as the reference, this specification assumes it is already running. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 361

AppendixA Electrical Characteristics 4 Jitter is the average deviation from the programmed frequency measured over the specified interval at maximum f . BUS Measurements are made with the device powered by filtered supplies and clocked by a stable external clock signal. Noise injected into the FLL circuitry via V and V and variation in crystal oscillator frequency increase the C percentage for a given DD SS Jitter interval. 5 Jitter measurements are based upon a 48 MHz MCGOUT clock frequency.. 6 Below D minimum, the MCG is guaranteed to enter lock. Above D maximum, the MCG will not enter lock. But if the MCG lock lock is already in lock, then the MCG may stay in lock. 7 Below D minimum, the MCG will not exit lock if already in lock. Above D maximum, the MCG is guaranteed to exit lock. unl unl o A.12 AC Characteristics This section describes ac timing characteristics for each peripheral system. A.12.1 Control Timing TableA-13. Control Timing Num C Parameter Symbol Min Typ1 Max Unit 1 Bus frequency (t = 1/f ) f dc — 24 MHz cyc Bus Bus 2 Internal low-power oscillator period t 700 1300 μs LPO 3 External reset pulse width2 t 100 — ns extrst 4 Reset low drive t 66 x t — ns rstdrv cyc 5 Active background debug mode latch setup time t 500 — ns MSSU 6 Active background debug mode latch hold time t 100 — ns MSH 7 IRQ pulse width Asynchronous path2 t t 100 — — ns ILIH, IHIL Synchronous path3 1.5 x t cyc 8 KBIPx pulse width Asynchronous path2 t t 100 — — ns ILIH, IHIL Synchronous path3 1.5 x t cyc 9 Port rise and fall time t , t Rise Fall low output drive (PTxDS = 0), (load = 50 pF)4 — 40 Slew rate control disabled (PTxSE = 0) — 75 Slew rate control enabled (PTxSE = 1) ns high output drive (PTxDS = 1), (load = 50 pF) Slew rate control disabled (PTxSE = 0) — 11 Slew rate control enabled (PTxSE = 1) — 35 1 Typical values are based on characterization data at V = 5.0 V, 25 °C unless otherwise stated. DD 2 This is the shortest pulse that is guaranteed to be recognized as a reset pin request. Shorter pulses are not guaranteed to override reset requests from internal sources. 3 This is the minimum pulse width that is guaranteed to pass through the pin synchronization circuitry. Shorter pulses may or may not be recognized. In stop mode, the synchronizer is bypassed so shorter pulses can be recognized in that case. 4 Timing is shown with respect to 20% V and 80% V levels. Temperature range –40 °C to 85 °C. DD DD MC9S08JM60 Series Data Sheet, Rev. 5 362 Freescale Semiconductor

AppendixA Electrical Characteristics t extrst RESET PIN FigureA-6. Reset Timing t IHIL IRQ/KBIPx IRQ/KBIPx t ILIH FigureA-7. IRQ/KBIPx Timing A.12.2 Timer/PWM (TPM) Module Timing Synchronizer circuits determine the shortest input pulses that can be recognized or the fastest clock that can be used as the optional external source to the timer counter. These synchronizers operate from the current bus rate clock. TableA-14. TPM Input Timing NUM C Function Symbol Min Max Unit 1 — External clock frequency f dc f /4 MHz TPMext Bus 2 — External clock period t 4 — t TPMext cyc 3 D External clock high time t 1.5 — t clkh cyc 4 D External clock low time t 1.5 — t clkl cyc 5 D Input capture pulse width t 1.5 — t ICPW cyc t TPMext t clkh TPMxCLK t clkl FigureA-8. Timer External Clock MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 363

AppendixA Electrical Characteristics t ICPW TPMxCHn TPMxCHn t ICPW FigureA-9. Timer Input Capture Pulse A.12.3 SPI Characteristics Table A-15 and FigureA-10 through Figure A-13 describe the timing requirements for the SPI system. TableA-15. SPI Electrical Characteristic Num1 C Characteristic2 Symbol Min Max Unit Operating frequency 1 D Master f f /2048 f /2 op Bus Bus Hz Slave f dc f /4 op Bus Cycle time 2 D Master t 2 2048 t SCK cyc Slave t 4 — t SCK cyc Enable lead time 3 D Master t — 1/2 t Lead SCK Slave t 1/2 — t Lead SCK Enable lag time 4 D Master t — 1/2 t Lag SCK Slave t 1/2 — t Lag SCK Clock (SPSCK) high time Master and 5 D Slave t 1/2 t – 25 — ns SCKH SCK Clock (SPSCK) low time Master and 6 D Slave t 1/2 t – 25 — ns SCKL SCK Data setup time (inputs) 7 D Master t 30 — ns SI(M) Slave t 30 — ns SI(S) Data hold time (inputs) 8 D Master t 30 — ns HI(M) Slave t 30 — ns HI(S) 9 D Access time, slave3 t 0 40 ns A 10 D Disable time, slave4 t — 40 ns dis Data setup time (outputs) 11 D Master t 25 — ns SO Slave t 25 — ns SO Data hold time (outputs) 12 D Master t –10 — ns HO Slave t –10 — ns HO MC9S08JM60 Series Data Sheet, Rev. 5 364 Freescale Semiconductor

AppendixA Electrical Characteristics 1 Refer to FigureA-10 through FigureA-13. 2 All timing is shown with respect to 20% V and 70% V , unless noted; 100 pF load on all SPI pins. All DD DD timing assumes slew rate control disabled and high drive strength enabled for SPI output pins. 3 Time to data active from high-impedance state. 4 Hold time to high-impedance state. SS1 (OUTPUT) 2 1 3 SCK 5 (CPOL = 0) (OUTPUT) 4 SCK 5 (CPOL = 1) 4 (OUTPUT) 6 7 MISO (INPUT) MSB IN2 BIT 6 . . . 1 LSB IN 10 10 11 MOSI MSB OUT2 BIT 6 . . . 1 LSB OUT (OUTPUT) NOTES: 1. SS output mode (MODFEN = 1, SSOE = 1). 2. LSBF = 0. For LSBF = 1, bit order is LSB, bit 1, ..., bit 6, MSB. FigureA-10. SPI Master Timing (CPHA = 0) MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 365

AppendixA Electrical Characteristics SS(1) (OUTPUT) 1 2 3 SCK 5 (CPOL = 0) (OUTPUT) 4 SCK 5 (CPOL = 1) 4 (OUTPUT) 6 7 MISO (INPUT) MSB IN(2) BIT 6 . . . 1 LSB IN 10 11 MOSI MSB OUT(2) BIT 6 . . . 1 LSB OUT (OUTPUT) NOTES: 1. SS output mode (MODFEN = 1, SSOE = 1). 2. LSBF = 0. For LSBF = 1, bit order is LSB, bit 1, ..., bit 6, MSB. FigureA-11. SPI Master Timing (CPHA = 1) SS (INPUT) 1 3 SCK 5 (CPOL = 0) (INPUT) 4 2 SCK 5 (CPOL = 1) (INPUT) 4 9 8 10 11 MISO SEE (OUTPUT) SLAVE MSB OUT BIT 6 . . . 1 SLAVE LSB OUT NOTE 6 7 MOSI (INPUT) MSB IN BIT 6 . . . 1 LSB IN NOTE: 1. Not defined but normally MSB of character just received FigureA-12. SPI Slave Timing (CPHA = 0) MC9S08JM60 Series Data Sheet, Rev. 5 366 Freescale Semiconductor

AppendixA Electrical Characteristics SS (INPUT) 1 3 2 SCK (CPOL = 0) 5 (INPUT) 4 SCK 5 (CPOL = 1) 4 (INPUT) 10 11 9 MISO SEE (OUTPUT) NOTE SLAVE MSB OUT BIT 6 . . . 1 SLAVE LSB OUT 8 6 7 MOSI (INPUT) MSB IN BIT 6 . . . 1 LSB IN NOTE: 1. Not defined but normally LSB of character just received FigureA-13. SPI Slave Timing (CPHA = 1) A.13 Flash Specifications This section provides details about program/erase times and program-erase endurance for the flash memory. Program and erase operations do not require any special power sources other than the normal V supply. DD For more detailed information about program/erase operations. TableA-16. Flash Characteristics Num C Characteristic Symbol Min Typ1 Max Unit 1 Supply voltage for program/erase V 2.7 5.5 V prog/erase 2 Supply voltage for read operation V 2.7 5.5 V Read 3 Internal FCLK frequency2 f 150 200 kHz FCLK 4 Internal FCLK period (1/FCLK) t 5 6.67 μs Fcyc 5 Byte program time (random location)(2) t 9 t prog Fcyc 6 Byte program time (burst mode)(2) t 4 t Burst Fcyc 7 Page erase time3 t 4000 t Page Fcyc 8 Mass erase time(2) t 20,000 t Mass Fcyc 9 C Program/erase endurance4 T to T = –40°C to + 85°C 10,000 — — cycles L H T = 25°C — 100,000 — 10 Data retention5 t 15 100 — years D_ret 1 Typical values are based on characterization data at V = 5.0 V, 25°C unless otherwise stated. DD MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 367

AppendixA Electrical Characteristics 2 The frequency of this clock is controlled by a software setting. 3 These values are hardware state machine controlled. User code does not need to count cycles. This information supplied for calculating approximate time to program and erase. 4 Typical endurance for Flash is based on the intrinsic bitcell performance. For additional information on how Freescale Semiconductor defines typical endurance, please refer to Engineering Bulletin EB619/D, Typical Endurance for Nonvolatile Memory. 5 Typical data retention values are based on intrinsic capability of the technology measured at high temperature and de-rated to 25 °C using the Arrhenius equation. For additional information on how Freescale Semiconductor defines typical data retention, please refer to Engineering Bulletin EB618/D, Typical Data Retention for Nonvolatile Memory. A.14 USB Electricals The USB electricals for the S08USBV1 module conform to the standards documented by the Universal Serial Bus Implementers Forum. For the most up-to-date standards, visit http://www.usb.org. If the Freescale S08USBV1 implementation has electrical characteristics that deviate from the standard or require additional information, this space would be used to communicate that information. TableA-17. Internal USB 3.3V Voltage Regulator Characteristics Symbol Unit Min Typ Max Regulator operating voltage V V 3.9 — 5.5 regin VREG output V V 3 3.3 3.6 regout V input with internal V V 3 3.3 3.6 USB33 usb33in VREG disabled VREG Quiescent Current I mA — 0.5 — VRQ A.15 EMC Performance Electromagnetic compatibility (EMC) performance is highly dependant on the environment in which the MCU resides. Board design and layout, circuit topology choices, location and characteristics of external components as well as MCU software operation all play a significant role in EMC performance. The system designer must consult Freescale applications notes such as AN2321, AN1050, AN1263, AN2764, and AN1259 for advice and guidance specifically targeted at optimizing EMC performance. A.15.1 Radiated Emissions Microcontroller radiated RF emissions are measured from 150 kHz to 1 GHz using the TEM/GTEM Cell method in accordance with the IEC 61967-2 and SAE J1752/3 standards. The measurement is performed with the microcontroller installed on a custom EMC evaluation board while running specialized EMC test software. The radiated emissions from the microcontroller are measured in a TEM cell in two package orientations (North and East). For more detailed information concerning the evaluation results, conditions and setup, please refer to the EMC Evaluation Report for this device. The maximum radiated RF emissions of the tested configuration in all orientations are less than or equal to the reported emissions levels. MC9S08JM60 Series Data Sheet, Rev. 5 368 Freescale Semiconductor

AppendixA Electrical Characteristics TableA-18. Radiated Emissions Level1 Parameter Symbol Conditions Frequency f /f Unit OSC BUS (Max) 0.15 – 50 MHz 20 50 – 150 MHz 27 dBμV 150 – 500 MHz 27 Radiated emissions, V = 5.0 V 4 MHz crystal V DD electric field RE_TEM T = +25oC 24 MHz Bus A 500 – 1000 MHz 16 IEC Level 1 — SAE Level 3 — 1 Data based on qualification test results. MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 369

AppendixA Electrical Characteristics MC9S08JM60 Series Data Sheet, Rev. 5 370 Freescale Semiconductor

Appendix B Ordering Information and Mechanical Drawings B.1 Ordering Information This section contains ordering numbers for MC9S08JM60 series devices. See below for an example of the device numbering system. TableB-1. Device Numbering System Memory Available Packages2 Device Number1 Flash RAM Type MC9S08JM60 60,912 4096 64-pin LQFP 64-pin QFP MC9S08JM32 32,768 2048 48-pin QFN 44-pin LQFP 1 See Table1-1 for a complete description of modules included on each device. 2 See TableB-2 for package information. B.2 Orderable Part Numbering System MC 9 S08JM 60 C XX E Pb free indicator Status (MC = Fully Qualified) Package designator (See TableB-2) Memory Temperature range (9 = Flash-based) (C = –40°C to 85°C) Core Family Memory size designator B.3 Mechanical Drawings This following pages contain mechanical specifications for MC9S08JM60 series package options. See Table B-2 for the document numbers that correspond to each package type. TableB-2. Package Information Pin Count Type Designator Document No. 44 LQFP LD 98ASS23225W 48 QFN GT 98ARH99048A 64 LQFP LH 98ASS23234W 64 QFP QH 98ASB42844B MC9S08JM60 Series Data Sheet, Rev. 5 Freescale Semiconductor 371

None

None

How to Reach Us: Information in this document is provided solely to enable system and software implementers to use Freescale products. There are no express Home Page: or implied copyright licenses granted hereunder to design or fabricate freescale.com any integrated circuits based on the information in this document. Web Support: Freescale reserves the right to make changes without further notice to freescale.com/support any products herein. Freescale makes no warranty, representation, or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters that may be provided in Freescale data sheets and/or specifications can and do vary in different applications, and actual performance may vary over time. All operating parameters, including “typicals,” must be validated for each customer application by customer's technical experts. Freescale does not convey any license under its patent rights nor the rights of others. Freescale sells products pursuant to standard terms and conditions of sale, which can be found at the following address: freescale.com/SalesTermsandConditions. Freescale and the Freescale logo are trademarks of Freescale Semiconductor, Inc., Reg. U.S. Pat. & Tm. Off. All other product or service names are the property of their respective owners. © 2007-2014 Freescale Semiconductor, Inc. Document Number MC9S08JM60 Revision 5, 10/2014

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: N XP: MC9S08JM60CGT MC9S08JM60CLD MC9S08JM60CLH MC9S08JM60CQH MC9S08JM60CLDR MC9S08JM32CQH MC9S08JM32CLH MC9S08JM32CLD MC9S08JM32CGT