MC33174 - MC35174 LOW POWER QUAD BIPOLAR OPERATIONAL AMPLIFIERS n GOOD CONSUMPTION/SPEED RATIO : ONLY 200µA FOR 2.1MHz, 2Vµs n SINGLE (OR DUAL) SUPPLY OPERATION FROM +4V TO +44V (±2V TO ±22V) n WIDE INPUT COMMON MODE MODE VOLTAGE RANGE INCLUDING V - CC N n LOW LEVEL OUTPUT VOLTAGE CLOSE TO DIP14 V - : 100mV TYPICAL (Plastic Package) CC n PIN TO PIN COMPATIBLE WITH STANDARD QUAD OP-AMPs DESCRIPTION The MC3x174 series are quad bipolar operational D amplifier offering both low consumption (200µA) SO14 (Plastic Micropackage) and good speed (2.1MHz, 2V/µs). Moreover the Input Common Mode Range ex- tends down to the lower supply rail, allowing single PIN CONNECTIONS (top view) supply operation from +4V to +44V. ORDER CODE Output 1 1 14 Output 4 Package Part Number Temperature Inverting Input 1 2 - - 13 Inverting Input 4 Range N D Non-inverting Input 1 3 + + 12 Non-inverting Input 4 MC33174 -40°C, +105°C • • VC C + 4 11 VCC- MC35174 -55°C, +125°C • • Non-inverting Input 2 5 + + 10 Non-inverting Input 3 Example : MC33174N Inverting Input 2 6 - - 9 Inverting Input 3 Output 2 7 8 Output 3 N = Dual in Line Package (DIP) D = Small Outline Package (SO) - also available in Tape & Reel (DT)) April 2002 1/5

MC33174-MC35174 SCHEMATIC DIAGRAM (for 1/4 MC33174) V + CC R4 R5 R6 T7 T8 T9 T10 T11 T12 T13 T1 R7 R8 T25 R3 T15 T16 Input + T24 T6 Input - T17 T26 R13 T14 C R12 Output T5 T22 T13 R14 T2 T21 T19 T27 T28 T3 T20 T4 T29 R1 R2 R9 R10 R11 T23 R15 T30 T31 V - CC MAXIMUM RATINGS Symbol Parameter Value Unit V Supply Voltage ±22 V CC Vid Differential Input Voltage see note 1) V V Input Voltage see note 1 V i Output Short Circuit Duration Indefinite s Operating Free-Air Temperature range MC33174 -40 to 105 T °C oper MC35174 -55 to 125 Tj Junction Temperature 150 °C T Storage Temperature -65 to 150 °C stg 1. Either or both input voltages must not exceed the magnitude of Vcc. OPERATING CONDITIONS Symbol Parameter Value Unit V Supply Voltage ±2 to ±22 V CC 2/5

MC33174-MC35174 ELECTRICAL CHARACTERISTICS V + = +15V, V - = -15V, R connected to Ground, T = 25°C (unless otherwise specified) CC CC L amb Symbol Parameter Min. Typ. Max. Unit Input Offset Voltage VCC+ = +15V, VCC- = -15V, Vic = 0V 1 4.5 Vio V + = 5V, V - = 0V, V = 0V, V = 1.4V 1 5 mV CC CC ic o V + = +15V, V - = -15V, V = 0V, T £ T £ T 6.5 CC CC ic min. amb max. DVio Input Offset Voltage Drift 10 µV/°C Iio InpTut O. f£fs eTt Cu r£r eTnt (Vic = 0V) 5 2400 nA min amb max. Iib InpTut B £ia sT Cu r£re Tnt (Vic = 0V) 20 120000 nA min. amb max. Avd LaTrge S. £ig Tnal V o£ l tTage Gain (RL = 10kW , Vo = ±10V) 5205 100 V/mV min amb max. High Level Output Voltage VOH VVCC++ == 5+V1,5 VV,C VC- = -0 =V ,- 1R5LV =, R10 k=W 10kW 133.5.6 144..22 V CC CC L V + = +15V, V - = -15V, R = 10kW , T £ T £ T 13.3 CC CC L min. amb max Low Level Output Voltage VOL VVCC++ == 5+V1,5 VV,C CV- = - 0=V -, 1R5LV =, R10 k=W 10kW -01.14 -01.31.56 V CC CC L V + = +15V, V - = -15V, R = 10kW , T £ T £ T -13.3 CC CC L min. amb max Output Short Circuit Current (V = ±1V, V = 0V) id o Isc Source 3 6 mA Sink 15 27 Vicm InpTumt iCn.o £m Tmamonb £M oTdmea xVoltage Range VVCC-- ttoo ((VVCC++ -- 12..82)) V CC CC CMR Common-mode Rejection Ratio (Vic = Vicm min.) 80 100 dB SVR Supply Voltage Rejection Ratio (VCC = ±5 to ±15V) 80 100 dB Supply Current ICC VVCC++ == 5+V1,5 VV,C CV- = - 0=V -, 1n5oV l,o naod load 220200 225500 m A CC CC V + = +15V, V - = -15V, no load, T £ T £ T 300 CC CC min. amb max SR Slew Rate (Vi = ±10V, RL = 10kW , CL = 100pF) 1.6 2 V/µs Gain Bandwidth Product GBP R = 10kW , C = 100pF, f = 100kHz 1.4 2.1 MHz L L f m Phase Margin (RL = 10kW , CL = 100pF) 45 Degrees nV en Equivalent Input Noise Voltage (f = 1kHz) 29 ------------ Hz THD Total Harmonic Distortion 0.05 % VO1/VO2 Channel Separation 120 dB 3/5

MC33174-MC35174 PACKAGE MECHANICAL DATA 14 PINS - PLASTIC DIP Millimeters Inches Dimensions Min. Typ. Max. Min. Typ. Max. a1 0.51 0.020 B 1.39 1.65 0.055 0.065 b 0.5 0.020 b1 0.25 0.010 D 20 0.787 E 8.5 0.335 e 2.54 0.100 e3 15.24 0.600 F 7.1 0.280 i 5.1 0.201 L 3.3 0.130 Z 1.27 2.54 0.050 0.100 4/5

MC33174-MC35174 PACKAGE MECHANICAL DATA 14 PINS - PLASTIC MICROPACKAGE (SO) L G c1 C 2 A a b e s 1 1 a b e3 E D M 14 8 F 1 7 Millimeters Inches Dimensions Min. Typ. Max. Min. Typ. Max. A 1.75 0.069 a1 0.1 0.2 0.004 0.008 a2 1.6 0.063 b 0.35 0.46 0.014 0.018 b1 0.19 0.25 0.007 0.010 C 0.5 0.020 c1 45° (typ.) D (1) 8.55 8.75 0.336 0.344 E 5.8 6.2 0.228 0.244 e 1.27 0.050 e3 7.62 0.300 F (1) 3.8 4.0 0.150 0.157 G 4.6 5.3 0.181 0.208 L 0.5 1.27 0.020 0.050 M 0.68 0.027 S 8° (max.) Note : (1) D and F do not include mold flash or protrusions - Mold flash or protrusions shall not exceed 0.15mm (.066 inc) ONLY FOR DATA BOOK. Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. © The ST logo is a registered trademark of STMicroelectronics © 2002 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States © http://www.st.com 5/5

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: S TMicroelectronics: MC33174D MC33174DT MC33174N