Notice for TAIYO YUDEN products Please read this notice before using the TAIYO YUDEN products. REMINDERS ■ Product Information in this Catalog (4) Power generation control equipment (nuclear power, Product information in this catalog is as of October 2019. All of the hydroelectric power, thermal power plant control system, etc.) contents specified herein and production status of the products listed (5) Undersea equipment (submarine repeating equipment, in this catalog are subject to change without notice due to technical underwater work equipment, etc.) improvement of our products, etc. Therefore, please check for the (6) Military equipment latest information carefully before practical application or use of our (7) Any other equipment requiring extremely high levels of safety products. and/or reliability equal to the equipment listed above Please note that TAIYO YUDEN shall not be in any way responsible *Notes: for any damages and defects in products or equipment incorporating 1. There is a possibility that our products can be used only our products, which are caused under the conditions other than those for aviation equipment that does not directly affect the safe specified in this catalog or individual product specification sheets. operation of aircraft (e.g., in-flight entertainment, cabin light, electric seat, cooking equipment) if such use meets ■ Approval of Product Specifications requirements specified separately by TAIYO YUDEN. Please Please contact TAIYO YUDEN for further details of product be sure to contact TAIYO YUDEN for further information specifications as the individual product specification sheets are before using our products for such aviation equipment. available. When using our products, please be sure to approve our 2. Implantable medical devices contain not only internal unit product specifications or make a written agreement on the product which is implanted in a body, but also external unit which is specification with TAIYO YUDEN in advance. connected to the internal unit. ■ Pre-Evaluation in the Actual Equipment and Conditions 4. Limitation of Liability Please conduct validation and verification of our products in actual Please note that unless you obtain prior written consent of TAIYO conditions of mounting and operating environment before using our YUDEN, TAIYO YUDEN shall not be in any way responsible for products. any damages incurred by you or third parties arising from use of the products listed in this catalog for any equipment that is not ■ Limited Application intended for use by TAIYO YUDEN, or any equipment requiring 1. Equipment Intended for Use inquiry to TAIYO YUDEN or prohibited for use by TAIYO YUDEN The products listed in this catalog are intended for general- as described above. purpose and standard use in general electronic equipment (e.g., AV equipment, OA equipment, home electric appliances, office ■ Safety Design equipment, information and communication equipment including, When using our products for high safety and/or reliability-required without limitation, mobile phone, and PC) and other equipment equipment or circuits, please fully perform safety and/or reliability specified in this catalog or the individual product specification sheets. evaluation. In addition, please install (i) systems equipped with a protection circuit and a protection device and/or (ii) systems TAIYO YUDEN has the line-up of the products intended for equipped with a redundant circuit or other system to prevent an use in automotive electronic equipment, telecommunications unsafe status in the event of a single fault for a failsafe design to infrastructure and industrial equipment, or medical devices ensure safety. classified as GHTF Classes A to C (Japan Classes I to III). Therefore, when using our products for these equipment, ■ Intellectual Property Rights please check available applications specified in this catalog Information contained in this catalog is intended to convey examples or the individual product specification sheets and use the of typical performances and/or applications of our products and is corresponding products. not intended to make any warranty with respect to the intellectual property rights or any other related rights of TAIYO YUDEN or any 2. Equipment Requiring Inquiry third parties nor grant any license under such rights. Please be sure to contact TAIYO YUDEN for further information before using the products listed in this catalog for the following ■ Limited Warranty equipment (excluding intended equipment as specified in this Please note that the scope of warranty for our products is limited to catalog or the individual product specification sheets) which may the delivered our products themselves and TAIYO YUDEN shall not cause loss of human life, bodily injury, serious property damage be in any way responsible for any damages resulting from a failure and/or serious public impact due to a failure or defect of the or defect in our products. Notwithstanding the foregoing, if there is products and/or malfunction attributed thereto. a written agreement (e.g., supply and purchase agreement, quality (1) Transportation equipment (automotive powertrain control assurance agreement) signed by TAIYO YUDEN and your company, system, train control system, and ship control system, etc.) TAIYO YUDEN will warrant our products in accordance with such (2) Traffic signal equipment agreement. (3) Disaster prevention equipment, crime prevention equipment (4) Medical devices classified as GHTF Class C (Japan Class III) ■ TAIYO YUDEN’s Official Sales Channel (5) Highly public information network equipment, data- The contents of this catalog are applicable to our products which are processing equipment (telephone exchange, and base purchased from our sales offices or authorized distributors (hereinafter station, etc.) “TAIYO YUDEN’s official sales channel”). Please note that the contents (6) Any other equipment requiring high levels of quality and/or of this catalog are not applicable to our products purchased from any reliability equal to the equipment listed above seller other than TAIYO YUDEN’s official sales channel. 3. Equipment Prohibited for Use ■ Caution for Export Please do not incorporate our products into the following Some of our products listed in this catalog may require specific equipment requiring extremely high levels of safety and/or procedures for export according to“ U.S. Export Administration reliability. Regulations”,“ Foreign Exchange and Foreign Trade Control Law” (1) Aerospace equipment (artificial satellite, rocket, etc.) of Japan, and other applicable regulations. Should you have any (2) Aviation equipment *1 questions on this matter, please contact our sales staff. (3) Medical devices classified as GHTF Class D (Japan Class IV), implantable medical devices *2 20

for General Electronic Equipment for General Electronic Equipment TM METAL CORE WIRE-WOUND CHIP POWER INDUCTORS (MCOIL MA SERIES) METAL CORE WIRE-WOUND CHIP POWER INDUCTORS（MCOILTM MA SERIES） REFLOW REFLOW ■PARTS NUMBER * Operating Temp.：-40～+105℃（Including self-generated heat） M A K K 2 0 1 6 T 1 R 0 M △ △ △＝Blank space ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ①Series name ⑤Nominal inductance Code Series name Code IN Nominal inductance［μH］ D MA Metal Core Wire-wound Chip Power Inductor （example） U R47 0.47 CT ②Dimensions（T） 1R0 1.0 O R Code Dimensions（T）［mm］ 4R7 4.7 S KK 1.0 ※R＝Decimal point MK 1.2 ⑥Inductance tolerance P O ③Dimensions（L×W） Code Inductance tolerance W Dimensions M ±20％ Code Type（inch） E （L×W）［mm］ R 2016 2016（0806） 2.0×1.6 ⑦Special code IN 2520 2520（1008） 2.5×2.0 Code Special code D △ Standard U ④Packaging C Code Packaging ⑧Internal code T O T Taping R S ■STANDARD EXTERNAL DIMENSIONS / STANDARD QUANTITY Recommended Land Patterns L W Surface Mounting ・Mounting and soldering conditions should be checked beforehand. T ・Applicable soldering process to these products is reflow soldering only. Type A B C e C 2016 0.７ 0.8 1.8 2520 0.8 1.2 2.0 A B A Unit：mm Standard quantity［pcs］ Type L W T e Taping 2.0±0.1 1.6±0.1 1.0 max 0.5±0.3 MAKK2016 3000 （0.079±0.004） （0.063±0.004） （0.039 max） （0.020±0.012） 2.5±0.2 2.0±0.2 1.0 max 0.5±0.3 MAKK2520 3000 （0.098±0.008） （0.079±0.008） （0.039 max） （0.020±0.012） 2.5±0.2 2.0±0.2 1.2 max 0.5±0.3 MAMK2520 3000 （0.098±0.008） （0.079±0.008） （0.047 max） （0.020±0.012） Unit：mm（inch） i_wound_MA_e-E08R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 20 49

for General Electronic Equipment ■PARTS NUMBER ●MAKK2016（0806） type 【Thickness：1.0mm max.】 Self-resonant Rated current　※）　［ｍA］（max.） Nominal inductance DC Resistance Measuring Parts number EHS ［μH］ Inductance tolerance frequency ［Ω］（max.） Saturation current Temperature rise current frequency［MHz］ ［MHｚ］（min.） Idc1 Idc2 MAKK2016TR24M RoHS 0.24 ±20％ - 0.037 4,200 3,000 2 MAKK2016TR33M RoHS 0.33 ±20％ - 0.040 3,600 3,200 2 MAKK2016TR47M RoHS 0.47 ±20％ - 0.460 3,200 2,800 2 MAKK2016TR68M RoHS 0.68 ±20％ - 0.065 2,500 2,500 2 MAKK2016T1R0M RoHS 1.0 ±20％ - 0.075 2,200 2,200 2 MAKK2016T1R5M RoHS 1.5 ±20％ - 0.130 1,600 1,650 2 MAKK2016T2R2M RoHS 2.2 ±20％ - 0.160 1,500 1,500 2 MAKK2016T3R3M RoHS 3.3 ±20％ - 0.255 1,150 1,200 2 MAKK2016T4R7M RoHS 4.7 ±20％ - 0.380 1,000 950 2 IN D ●MAKK2520（1008） type 【Thickness：1.0mm max.】 U C Self-resonant Rated current　※）　［ｍA］（max.） TO Parts number EHS Nomina［lμ inHdu］ctance Inductance tolerance frequency DC［Ω R］e（smistaaxn.）ce Saturation current Temperature rise current freqMueeanscuyr［inMgHz］ R ［MHｚ］（min.） Idc1 Idc2 S MAKK2520TR33M RoHS 0.33 ±20％ - 0.038 4,700 3,500 2 MAKK2520TR47M RoHS 0.47 ±20％ - 0.046 3,900 3,200 2 MAKK2520TR68M RoHS 0.68 ±20％ - 0.059 3,700 2,900 2 MAKK2520T1R0M RoHS 1.0 ±20％ - 0.072 2,700 2,500 2 P O MAKK2520T1R5M RoHS 1.5 ±20％ - 0.125 2,300 1,800 2 W MAKK2520T2R2M RoHS 2.2 ±20％ - 0.156 1,900 1,500 2 MAKK2520T3R3M RoHS 3.3 ±20％ - 0.200 1,550 1,300 2 E MAKK2520T4R7M RoHS 4.7 ±20％ - 0.300 1,300 1,100 2 R IN ●MAMK2520（1008） type 【Thickness：1.2mm max.】 D Self-resonant Rated current　※）　［ｍA］（max.） U Parts number EHS Nomina［lμ inHdu］ctance Inductance tolerance frequency DC［Ω R］e（smistaaxn.）ce Saturation current Temperature rise current freqMueeanscuyr［inMgHz］ C ［MHｚ］（min.） Idc1 Idc2 T MAMK2520TR47M RoHS 0.47 ±20％ - 0.039 4,200 3,400 2 O MAMK2520TR68M RoHS 0.68 ±20％ - 0.048 3,200 3,200 2 R MAMK2520T1R0M RoHS 1.0 ±20％ - 0.059 3,100 2,700 2 S MAMK2520T2R2M RoHS 2.2 ±20％ - 0.110 2,000 1,900 2 MAMK2520T3R3M RoHS 3.3 ±20％ - 0.156 1,800 1,700 2 MAMK2520T4R7M RoHS 4.7 ±20％ - 0.260 1,500 1,300 2 ※） The saturation current value (Idc1) is the DC current value having inductance decrease down to 30%. (at 20℃)  ※） The temperature rise current value（Idc2) is the DC current value having temperature increase by 40℃. (at 20℃) ※） The rated current value is following either Idc1 or Idc2, which is the lower one. i_wound_MA_e-E08R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our product specification sheets. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our website (http://www.ty-top.com/) . 50 20

METAL CORE WIRE-WOUND CHIP POWER INDUCTORS (MCOILTM MA SERIES / MCOILTM MA-Ｈ SERIES) ■PACKAGING ①Minimum Quantity Standard Quantity [pcs] Type Tape ＆ Reel MAKK2016 3000 MAKK2520 3000 MAMK2520 3000 ②Tape Material ●Embossed Tape Top tape Chip Filled Sprocket hole Base tape Chip cavity Chip ③Taping dimensions ●Embossed tape 8mm wide (0.315 inches wide) φ1.5＋0.1/－0 1.75±0.1 Sprockethole (φ0.059＋0.004/-0) (0.069±0.004） A B 3.5±0.1(0.138±0.004) 8.0±0.20.315±0.008) ( F 4.0±0.1 (0.157±0.004) 2.0±0.05 (0.079±0.002) Electrode（bottom view） Chip cavity Insertion pitch Tape thickness Type A B F T K 1.9±0.1 2.3±0.1 4.0±0.1 0.25±0.05 1.2 max MAKK2016 （0.075±0.004） （0.091±0.004） （0.157±0.004） （0.009±0.002） （0.047 max） 2.3±0.1 2.8±0.1 4.0±0.1 0.3±0.05 1.25 max MAKK2520 (0.091±0.004) (0.110±0.004) （0.157±0.004） (0.012±0.002) （0.049 max） 2.3±0.1 2.8±0.1 4.0±0.1 0.3±0.05 1.4 max MAMK2520 (0.091±0.004) (0.110±0.004) (0.157±0.004) (0.012±0.002) (0.055 max) Unit：mm（inch） ④Leader and Blank portion Blank portions Chip cavity Blank portions Leader Direction of tape feed 160 mm or more 160 mm ～ 200 mm 400 mm ～ 560 mm ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_MA_pack_e-E05R01

⑤Reel size Reel size (Reference values) Type φD φd W MAKK2016 180+0/-3 60+1/-0 10.0±1.5 MAKK2520 （7.087+0/-0.118） （2.36+0.039/0） （0.394±0.059） MAMK2520 Unit：mm（inch） ⑥Top Tape Strength The top The top tape requires a peel-off force of 0.1 to 1.2N in the direction of the arrow as illustrated below. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_MA_pack_e-E05R01

METAL CORE WIRE-WOUND CHIP POWER INDUCTORS (MCOILTM MA SERIES / MCOILTM MA-Ｈ SERIES) ■RELIABILITY DATA 1. Operating Temperature Range MA series －40～＋105℃ Specified Value MA-H series －40～＋125℃ Test Methods and Including self-generated heat Remarks 2. Storage Temperature Range MA series Specified Value －40～＋85℃ MA-H series Test Methods and 0 to 40℃ for the product with taping. Remarks 3. Rated current MA series Specified Value Within the specified tolerance MA-H series 4. Inductance MA series Specified Value Within the specified tolerance MA-H series Test Methods and Measuring equipment : LCR Meter （HP 4285A or equivalent） Remarks Measuring frequency : 2MHz、1V 5. DC Resistance MA series Specified Value Within the specified tolerance MA-H series Test Methods and Measuring equipment : DC ohmmeter （HIOKI 3227 or equivalent） Remarks 6. Self resonance frequency MA series Specified Value － MA-H series 7. Temperature characteristic MA series Specified Value Inductance change : Within ±15% MA-H series Test Methods and Measurement of inductance shall be taken at temperature range within －40℃～＋85℃. Remarks With reference to inductance value at ＋20℃., change rate shall be calculated. 8. Resistance to flexure of substrate MA series Specified Value No damage MA-H series The test samples shall be soldered to the test board by the reflow. As illustrated below, apply force in the direction of the arrow indicating until deflection of the test board reaches to 2 mm. Test board size : 100×40×1.0 mm Test board material : Glass epoxy-resin Test Methods and Solder cream thickness : 0.12 mm Remarks ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_MA_reli_e-E08R01

9. Insulation resistance : between wires MA series Specified Value － MA-H series 10. Insulation resistance : between wire and core MA series Specified Value － MA-H series 11. Withstanding voltage : between wire and core MA series Specified Value － MA-H series 12. Adhesion of terminal electrode MA series Specified Value No abnormality. MA-H series The test samples shall be soldered to the test board by the reflow. Test Methods and Applied force : 10N to X and Y directions. Remarks Duration : 5s. Solder cream thickness : 0.12mm. 13. Resistance to vibration MA series Inductance change : Within ±10% Specified Value MA-H series No significant abnormality in appearance. The test samples shall be soldered to the test board by the reflow. Then it shall be submitted to below test conditions. Frequency Range 10～55Hz Total Amplitude 1.5mm (May not exceed acceleration 196m/s2) Test Methods and Sweeping Method 10Hz to 55Hz to 10Hz for 1min. Remarks X Time Y For 2 hours on each X, Y, and Z axis. Z Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48hrs. 14. Solderability MA series Specified Value At least 90％ of surface of terminal electrode is covered by new solder. MA-H series The test samples shall be dipped in flux, and then immersed in molten solder as shown in below table. Flux : Methanol solution containing rosin 25%. Test Methods and Solder Temperature 245±5℃ Remarks Time 5±0.5 sec. ※Immersion depth : All sides of mounting terminal shall be immersed. 15. Resistance to soldering heat MA series Inductance change : Within ±10% Specified Value MA-H series No significant abnormality in appearance. The test sample shall be exposed to reflow oven at 230℃ for 40 seconds, with peak temperature at 260＋0/－5℃ for 5 seconds, 3 times. Test Methods and Test board material : Glass epoxy-resin Remarks Test board thickness : 1.0mm Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48hrs. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_MA_reli_e-E08R01

16. Thermal shock MA series Inductance change : Within ±10% Specified Value MA-H series No significant abnormality in appearance. The test samples shall be soldered to the test board by the reflow. The test samples shall be placed at specified temperature for specified time by step 1 to step 4 as shown in below table in sequence. The temperature cycle shall be repeated 100 cycles. Conditions of 1 cycle Step Temperature (℃) Duration (min) Test Methods and 1 －40±3 30±3 Remarks 2 Room temperature Within 3 3 ＋85±2 30±3 4 Room temperature Within 3 Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48hrs. 17. Damp heat MA series Inductance change : Within ±10% Specified Value MA-H series No significant abnormality in appearance. The test samples shall be soldered to the test board by the reflow. The test samples shall be placed in thermostatic oven set at specified temperature and humidity as shown in below table. Test Methods and Temperature 60±2℃ Remarks Humidity 90～95%RH Time 500＋24/－0 hour Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48hrs. 18. Loading under damp heat MA series Inductance change : Within ±10% Specified Value MA-H series No significant abnormality in appearance. The test samples shall be soldered to the test board by the reflow. The test samples shall be placed in thermostatic oven set at specified temperature and humidity and applied the rated current continuously as shown in below table. Test Methods and Temperature 60±2℃ Remarks Humidity 90～95％RH Applied current Rated current Time 500＋24/－0 hour Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48hrs. 19. Low temperature life test MA series Inductance change : Within ±10% Specified Value MA-H series No significant abnormality in appearance. The test samples shall be soldered to the test board by the reflow. After that, the test samples shall be placed at test conditions as shown Test Methods and in below table. Remarks Temperature －40±2℃ Time 500＋24/－0 hour Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48hrs. 20. High temperature life test MA series Inductance change : Within ±10% Specified Value MA-H series No significant abnormality in appearance. The test samples shall be soldered to the test board by the reflow. After that, the test samples shall be placed at test conditions as shown Test Methods and in below table. Remarks Temperature 85±2℃ Time 500＋24/－0 hour Recovery : At least 2hrs of recovery under the standard condition after the test, followed by the measurement within 48hrs. 21. Loading at high temperature life test MA series Specified Value － MA-H series ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_MA_reli_e-E08R01

22. Standard condition Standard test condition : MA series Unless otherwise specified, temperature is 20±15℃ and 65±20％of relative humidity. Specified Value When there is any question concerning measurement result: In order to provide correlation MA-H series data, the test shall be condition of 20±2℃ of temperature, 65±5% relative humidity. Inductance is in accordance with our measured value. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_MA_reli_e-E08R01

METAL CORE WIRE-WOUND CHIP POWER INDUCTORS (MCOILTM MA SERIES / MCOILTM MA-Ｈ SERIES) ■PRECAUTIONS 1. Circuit Design ◆Operating environment 1. The products described in this specification are intended for use in general electronic equipment,(office supply equipment, telecommunications systems, measuring equipment, and household equipment). They are not intended for use in mission-critical Precautions equipment or systems requiring special quality and high reliability (traffic systems, safety equipment, aerospace systems, nuclear control systems and medical equipment including life-support systems,) where product failure might result in loss of life, injury or damage. For such uses, contact TAIYO YUDEN Sales Department in advance. 2. PCB Design ◆Land pattern design Precautions 1. Please refer to a recommended land pattern. ◆Land pattern design Technical Surface Mounting considerations ・ Mounting and soldering conditions should be checked beforehand. ・ Applicable soldering process to this products is reflow soldering only. 3. Considerations for automatic placement ◆Adjustment of mounting machine Precautions 1. Excessive impact load should not be imposed on the products when mounting onto the PC boards. 2. Mounting and soldering conditions should be checked beforehand. Technical ◆Adjustment of mounting machine considerations 1. When installing products, care should be taken not to apply distortion stress as it may deform the products. 4. Soldering ◆Reflow soldering 1. Please contact any of our offices for a reflow soldering, and refer to the recommended condition specified. 2. The product shall be used reflow soldering only. Precautions 3. Please do not add any stress to a product until it returns in normal temperature after reflow soldering. ◆Lead free soldering 1. When using products with lead free soldering, we request to use them after confirming adhesion, temperature of resistance to soldering heat, soldering etc sufficiently. ◆Reflow soldering 1. If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently degrade the reliability of the products. Recommended reflow condition (Pb free solder) Technical considerations 5. Cleaning ◆Cleaning conditions Precautions 1. Washing by supersonic waves shall be avoided. Technical ◆Cleaning conditions considerations 1. If washed by supersonic waves, the products might be broken. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_MA_prec_e-E06R01

6. Handling ◆Handling 1. Keep the product away from all magnets and magnetic objects. ◆Breakaway PC boards (splitting along perforations) 1. When splitting the PC board after mounting product, care should be taken not to give any stresses of deflection or twisting to the board. 2. Board separation should not be done manually, but by using the appropriate devices. ◆Mechanical considerations Precautions 1. Please do not give the product any excessive mechanical shocks. 2. Please do not add any shock and power to a product in transportation. ◆Pick-up pressure 1. Please do not push to add any pressure to a winding part. Please do not give any shock and push into a ferrite core exposure part. ◆Packing 1. Please avoid accumulation of a packing box as much as possible. ◆Handling 1. There is a case that a characteristic varies with magnetic influence. ◆Breakaway PC boards (splitting along perforations) 1. The position of the product on PCBs shall be carefully considered to minimize the stress caused from splitting of the PCBs. ◆Mechanical considerations Technical 1. There is a case to be damaged by a mechanical shock. considerations 2. There is a case to be broken by the handling in transportation. ◆Pick-up pressure 1. Damage and a characteristic can vary with an excessive shock or stress. ◆Packing 1. If packing boxes are accumulated, that could cause a deformation on packing tapes or a damage on the products. 7. Storage conditions ◆Storage 1. To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the storage area should be controlled. ・ Recommended conditions Ambient temperature : 0～40℃ Precautions Humidity : Below 70% RH ・ The ambient temperature must be kept below 30℃. Even under ideal storage conditions, solderability of products electrodes may decrease as time passes. For this reason, product should be used within 6 months from the time of delivery. In case of storage over 6 months, solderability shall be checked before actual usage. ◆Storage Technical 1. Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes considerations and deterioration of taping/packaging materials may take place. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_wound_MA_prec_e-E06R01

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: T aiyo Yuden: MAMK2520T1R0M MAMK2520T2R2M MAMK2520T3R3M MAMK2520T4R7M MAMK2520TR47M MAKK2016TR24M MAKK2520TR47M MAKK2016TR47M MAKK2520TR68M MAKK2016T1R5M MAKK2520T1R0M MAMK2520TR68M MAKK2016T1R0M MAKK2016T2R2M MAKK2016T3R3M MAKK2016T4R7M MAKK2520T2R2M MAKK2016TR68M MAKK2520T4R7M MAKK2016TR33M MAKK2520T1R5M MAKK2520T3R3M MAKK2520TR33M