M95128-A125 M95128-A145 Automotive 128-Kbit serial SPI bus EEPROMs with high-speed clock Datasheet - production data Features • Compatible with the Serial Peripheral Interface (SPI) bus • Memory array SO8 (MN) – 128 Kbit (16 Kbyte) of EEPROM 150 mil width – Page size: 64 byte – Write protection by block: 1/4, 1/2 or whole memory – Additional Write lockable Page (Identification page) TSSOP8 (DW) • Extended temperature and voltage ranges 169 mil width – Up to 125 °C (V from 1.7 V to 5.5 V) CC – Up to 145 °C (V from 2.5 V to 5.5 V) CC • High speed clock frequency – 20 MHz for V ≥ 4.5 V CC – 10 MHz for V ≥ 2.5 V CC – 5 MHz for V ≥ 1.7 V CC WFDFPN8 (MF) 2 x 3 mm • Schmitt trigger inputs for noise filtering • Short Write cycle time – Byte Write within 4 ms – Page Write within 4 ms • Write cycle endurance – 4 million Write cycles at 25 °C – 1.2 million Write cycles at 85 °C – 600 k Write cycles at 125 °C – 400 k Write cycles at 145 °C • Data retention – 50 years at 125 °C – 100 years at 25 °C • ESD Protection (Human Body Model) – 4000 V • Packages – RoHS-compliant and halogen-free (ECOPACK2®) January 2016 DocID023103 Rev 8 1/43 This is information on a product in full production. www.st.com

Contents M95128-A125 M95128-A145 Contents 1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2 Signal description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2.1 Serial Data output (Q) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2.2 Serial Data input (D) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2.3 Serial Clock (C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2.4 Chip Select (S) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2.5 Hold (HOLD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2.6 Write Protect (W) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2.7 V ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 SS 2.8 V supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 CC 3 Operating features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 3.1 Active power and Standby power modes . . . . . . . . . . . . . . . . . . . . . . . . . 10 3.2 SPI modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 3.3 Hold mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 3.4 Protocol control and data protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 3.4.1 Protocol control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3.4.2 Status Register and data protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 3.5 Identification page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 4 Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 4.1 Write Enable (WREN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 4.2 Write Disable (WRDI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 4.3 Read Status Register (RDSR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 4.4 Write Status Register (WRSR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 4.5 Read from Memory Array (READ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 4.6 Write to Memory Array (WRITE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 4.7 Read Identification Page (RDID) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 4.8 Write Identification Page (WRID) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 4.9 Read Lock Status (RDLS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 4.10 Lock Identification Page (LID) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 2/43 DocID023103 Rev 8

M95128-A125 M95128-A145 Contents 5 Application design recommendations . . . . . . . . . . . . . . . . . . . . . . . . . 26 5.1 Supply voltage (V ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 CC 5.1.1 Operating supply voltage (V ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 CC 5.1.2 Power-up conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 5.1.3 Power-down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 5.2 Implementing devices on SPI bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 5.3 Cycling with Error Correction Code (ECC) . . . . . . . . . . . . . . . . . . . . . . . . 28 6 Delivery state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 7 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 8 DC and AC parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 9 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 9.1 SO8N package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 9.2 TSSOP8 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 9.3 WFDFPN8 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 10 Part numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 11 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 DocID023103 Rev 8 3/43 3

List of tables M95128-A125 M95128-A145 List of tables Table 1. Signal names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Table 2. Status Register format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Table 3. Write-protected block size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Table 4. Protection modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Table 5. Device identification bytes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Table 6. Instruction set. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Table 7. Significant bits within the two address bytes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Table 8. Absolute maximum ratings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Table 9. Cycling performance by groups of 4 byte. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Table 10. Operating conditions (voltage range W, temperature range 4). . . . . . . . . . . . . . . . . . . . . . 30 Table 11. Operating conditions (voltage range R, temperature range 3). . . . . . . . . . . . . . . . . . . . . . 30 Table 12. Operating conditions (voltage range R, temperature range 3) for high-speed communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Table 13. DC characteristics (voltage range W, temperature range 4). . . . . . . . . . . . . . . . . . . . . . . . 31 Table 14. DC characteristics (voltage range R, temperature range 3). . . . . . . . . . . . . . . . . . . . . . . . 32 Table 15. AC characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Table 16. SO8N – 8-lead plastic small outline, 150 mils body width, package mechanical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Table 17. TSSOP8 – 8-lead thin shrink small outline, 3 x 4.4 mm, 0.65 mm pitch, package mechanical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Table 18. WFPN8 (MLP8) – 8-lead, 2 x 3 mm, 0.5 mm pitch very very thin fine pitch dual flat package mechanical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Table 19. Ordering information scheme. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Table 20. Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 4/43 DocID023103 Rev 8

M95128-A125 M95128-A145 List of figures List of figures Figure 1. Logic diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Figure 2. 8-pin package connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Figure 3. SPI modes supported. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Figure 4. Hold mode activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Figure 5. Write Enable (WREN) sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Figure 6. Write Disable (WRDI) sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Figure 7. Read Status Register (RDSR) sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Figure 8. Write Status Register (WRSR) sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Figure 9. Read from Memory Array (READ) sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Figure 10. Byte Write (WRITE) sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Figure 11. Page Write (WRITE) sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Figure 12. Read Identification Page sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Figure 13. Write Identification Page sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Figure 14. Read Lock Status sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Figure 15. Lock ID sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Figure 16. Bus master and memory devices on the SPI bus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Figure 17. AC measurement I/O waveform. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Figure 18. Serial input timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Figure 19. Hold timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Figure 20. Serial output timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Figure 21. SO8N – 8-lead plastic small outline, 150 mils body width, package outline. . . . . . . . . . . . 36 Figure 22. SO8N – 8-lead plastic small outline, 150 mils body width, package recommended footprint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Figure 23. TSSOP8 – 8-lead thin shrink small outline, 3 x 4.4 mm, 0.65 mm pitch, package outline. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Figure 24. WFDFPN8 (MLP8) – 8-lead, 2 x 3 mm, 0.5 mm pitch very very thin fine pitch dual flat package outline. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 DocID023103 Rev 8 5/43 5

Description M95128-A125 M95128-A145 1 Description The M95128-A125 and M95128-A145 are 128-Kbit serial EEPROM Automotive grade devices operating up to 145°C. They are compliant with the very high level of reliability defined by the Automotive standard AEC-Q100 grade 0. The devices are accessed by a simple serial SPI compatible interface running up to 20 MHz. The memory array is based on advanced true EEPROM technology (Electrically Erasable PROgrammable Memory). The M95128-A125 and M95128-A145 are byte-alterable memories (16384 × 8 bits) organized as 256 pages of 64 byte in which the data integrity is significantly improved with an embedded Error Correction Code logic. The M95128-A125 and M95128-A145 offer an additional Identification Page (64 byte) in which the ST device identification can be read. This page can also be used to store sensitive application parameters which can be later permanently locked in read-only mode. Figure 1. Logic diagram (cid:44)(cid:75)(cid:62)(cid:24) (cid:44)(cid:349)(cid:336)(cid:346)(cid:3)(cid:448)(cid:381)(cid:367)(cid:410)(cid:258)(cid:336)(cid:286) (cid:116) (cid:18)(cid:381)(cid:374)(cid:410)(cid:396)(cid:381)(cid:367)(cid:3)(cid:367)(cid:381)(cid:336)(cid:349)(cid:272) (cid:336)(cid:286)(cid:374)(cid:286)(cid:396)(cid:258)(cid:410)(cid:381)(cid:396) (cid:94) (cid:18) (cid:24) (cid:47)(cid:876)(cid:75)(cid:3)(cid:400)(cid:346)(cid:349)(cid:296)(cid:410)(cid:3)(cid:396)(cid:286)(cid:336)(cid:349)(cid:400)(cid:410)(cid:286)(cid:396) (cid:89) (cid:4)(cid:282)(cid:282)(cid:396)(cid:286)(cid:400)(cid:400)(cid:3)(cid:396)(cid:286)(cid:336)(cid:349)(cid:400)(cid:410)(cid:286)(cid:396) (cid:24)(cid:258)(cid:410)(cid:258) (cid:258)(cid:374)(cid:282)(cid:3)(cid:272)(cid:381)(cid:437)(cid:374)(cid:410)(cid:286)(cid:396) (cid:396)(cid:286)(cid:336)(cid:349)(cid:400)(cid:410)(cid:286)(cid:396) (cid:94)(cid:410)(cid:258)(cid:410)(cid:437)(cid:400) (cid:396)(cid:286)(cid:336)(cid:349)(cid:400)(cid:410)(cid:286)(cid:396) (cid:1005)(cid:876)(cid:1008) (cid:94)(cid:349)(cid:460)(cid:286)(cid:3)(cid:381)(cid:296)(cid:3)(cid:410)(cid:346)(cid:286) (cid:272)(cid:381)(cid:282)(cid:286)(cid:396) (cid:1005)(cid:876)(cid:1006) (cid:90)(cid:28)(cid:258)(cid:396)(cid:28)(cid:286)(cid:286)(cid:87)(cid:258)(cid:258)(cid:90)(cid:282)(cid:75)(cid:3)(cid:381)(cid:68)(cid:374)(cid:367)(cid:455) (cid:286) (cid:282) (cid:122)(cid:3) (cid:1005)(cid:3)(cid:393)(cid:258)(cid:336)(cid:286) (cid:47)(cid:282)(cid:286)(cid:374)(cid:410)(cid:349)(cid:296)(cid:349)(cid:272)(cid:258)(cid:410)(cid:349)(cid:381)(cid:374)(cid:3)(cid:393)(cid:258)(cid:336)(cid:286) (cid:121)(cid:3)(cid:282)(cid:286)(cid:272)(cid:381)(cid:282)(cid:286)(cid:396) (cid:48)(cid:54)(cid:20)(cid:28)(cid:26)(cid:22)(cid:22)(cid:57)(cid:20) 6/43 DocID023103 Rev 8

M95128-A125 M95128-A145 Description Figure 2. 8-pin package connections (cid:45)(cid:25)(cid:21)(cid:88)(cid:88)(cid:88) (cid:51) (cid:17) (cid:24) (cid:54)(cid:35)(cid:35) (cid:49) (cid:18) (cid:23) (cid:40)(cid:47)(cid:44)(cid:36) (cid:55) (cid:19) (cid:22) (cid:35) (cid:54)(cid:51)(cid:51) (cid:20) (cid:21) (cid:36) (cid:33)(cid:41)(cid:16)(cid:17)(cid:23)(cid:25)(cid:16)(cid:36) 1. See Package mechanical data section for package dimensions and how to identify pin-1. Table 1. Signal names Signal name Description C Serial Clock D Serial data input Q Serial data output S Chip Select W Write Protect HOLD Hold V Supply voltage CC V Ground SS DocID023103 Rev 8 7/43 42

Signal description M95128-A125 M95128-A145 2 Signal description All input signals must be held high or low (according to voltages of V or V , as specified in IH IL Table 13 and Table 14). These signals are described below. 2.1 Serial Data output (Q) This output signal is used to transfer data serially out of the device during a Read operation. Data is shifted out on the falling edge of Serial Clock (C), most significant bit (MSB) first. In all other cases, the Serial Data output is in high impedance. 2.2 Serial Data input (D) This input signal is used to transfer data serially into the device. D input receives instructions, addresses, and the data to be written. Values are latched on the rising edge of Serial Clock (C), most significant bit (MSB) first. 2.3 Serial Clock (C) This input signal allows to synchronize the timing of the serial interface. Instructions, addresses, or data present at Serial Data Input (D) are latched on the rising edge of Serial Clock (C). Data on Serial Data Output (Q) changes after the falling edge of Serial Clock (C). 2.4 Chip Select (S) Driving Chip Select (S) low selects the device in order to start communication. Driving Chip Select (S) high deselects the device and Serial Data output (Q) enters the high impedance state. 2.5 Hold (HOLD) The Hold (HOLD) signal is used to pause any serial communications with the device without deselecting the device. 2.6 Write Protect (W) This pin is used to write-protect the Status Register. 2.7 V ground SS V is the reference for all signals, including the V supply voltage. SS CC 8/43 DocID023103 Rev 8

M95128-A125 M95128-A145 Signal description 2.8 V supply voltage CC V is the supply voltage pin. Refer to Section 3.1: Active power and Standby power modes CC and to Section 5.1: Supply voltage (VCC). DocID023103 Rev 8 9/43 42

Operating features M95128-A125 M95128-A145 3 Operating features 3.1 Active power and Standby power modes When Chip Select (S) is low, the device is selected and in the Active power mode. When Chip Select (S) is high, the device is deselected. If a Write cycle is not currently in progress, the device then goes in to the Standby power mode, and the device consumption drops to I , as specified in Table 13 and Table 14. CC1 3.2 SPI modes The device can be driven by a microcontroller with its SPI peripheral running in either of the two following modes: • CPOL=0, CPHA=0 • CPOL=1, CPHA=1 For these two modes, input data is latched in on the rising edge of Serial Clock (C), and output data is available from the falling edge of Serial Clock (C). The difference between the two modes, as shown in Figure 3, is the clock polarity when the bus master is in Stand-by mode and not transferring data: • C remains at 0 for (CPOL=0, CPHA=0) • C remains at 1 for (CPOL=1, CPHA=1) Figure 3. SPI modes supported (cid:35)(cid:48)(cid:47)(cid:44)(cid:35)(cid:48)(cid:40)(cid:33) (cid:16) (cid:16) (cid:35) (cid:17) (cid:17) (cid:35) (cid:36) (cid:45)(cid:51)(cid:34) (cid:49) (cid:45)(cid:51)(cid:34) (cid:33)(cid:41)(cid:16)(cid:17)(cid:20)(cid:19)(cid:24)(cid:34) 10/43 DocID023103 Rev 8

M95128-A125 M95128-A145 Operating features 3.3 Hold mode The Hold (HOLD) signal is used to pause any serial communications with the device without resetting the clocking sequence. The Hold mode starts when the Hold (HOLD) signal is driven low and the Serial Clock (C) is low (as shown in Figure 4). During the Hold mode, the Serial Data output (Q) is high impedance, and the signals present on Serial Data input (D) and Serial Clock (C) are not decoded. The Hold mode ends when the Hold (HOLD) signal is driven high and the Serial Clock (C) is or becomes low. Figure 4. Hold mode activation (cid:35) (cid:40)(cid:47)(cid:44)(cid:36) (cid:40)(cid:79)(cid:76)(cid:68) (cid:40)(cid:79)(cid:76)(cid:68) (cid:67)(cid:79)(cid:78)(cid:68)(cid:73)(cid:84)(cid:73)(cid:79)(cid:78) (cid:35)(cid:67)(cid:79)(cid:79)(cid:78)(cid:78)(cid:68)(cid:68)(cid:73)(cid:73)(cid:84)(cid:84)(cid:73)(cid:73)(cid:79)(cid:79)(cid:78)(cid:78) (cid:45)(cid:51)(cid:17)(cid:25)(cid:23)(cid:23)(cid:24)(cid:54)(cid:17) Deselecting the device while it is in Hold mode resets the paused communication. 3.4 Protocol control and data protection 3.4.1 Protocol control The Chip Select (S) input offers a built-in safety feature, as the S input is edge-sensitive as well as level-sensitive: after power-up, the device is not selected until a falling edge has first been detected on Chip Select (S). This ensures that Chip Select (S) must have been high prior to going low, in order to start the first operation. For Write commands (WRITE, WRSR, WRID, LID) to be accepted and executed: • the Write Enable Latch (WEL) bit must be set by a Write Enable (WREN) instruction • a falling edge and a low state on Chip Select (S) during the whole command must be decoded • instruction, address and input data must be sent as multiple of eight bits • the command must include at least one data byte • Chip Select (S) must be driven high exactly after a data byte boundary Write command can be discarded at any time by a rising edge on Chip Select (S) outside of a byte boundary. To execute Read commands (READ, RDSR, RDID, RDLS), the device must decode: • a falling edge and a low level on Chip Select (S) during the whole command • instruction and address as multiples of eight bits (byte) From this step, data bits are shifted out until the rising edge on Chip Select (S). DocID023103 Rev 8 11/43 42

Operating features M95128-A125 M95128-A145 3.4.2 Status Register and data protection The Status Register format is shown in Table 2 and the status and control bits of the Status Register are as follows: Table 2. Status Register format b7 b6 b5 b4 b3 b2 b1 b0 SRWD 0 0 0 BP1 BP0 WEL WIP Status Register Write Protect Block Protect bits Write Enable Latch bit Write In Progress bit Note: Bits b6, b5, b4 are always read as 0. WIP bit The WIP bit (Write In Progress) is a read-only flag that indicates the Ready/Busy state of the device. When a Write command (WRITE, WRSR, WRID, LID) has been decoded and a Write cycle (t ) is in progress, the device is busy and the WIP bit is set to 1. When WIP=0, W the device is ready to decode a new command. During a Write cycle, reading continuously the WIP bit allows to detect when the device becomes ready (WIP=0) to decode a new command. WEL bit The WEL bit (Write Enable Latch) bit is a flag that indicates the status of the internal Write Enable Latch. When WEL is set to 1, the Write instructions (WRITE, WRSR, WRID, LID) are executed; when WEL is set to 0, any decoded Write instruction is not executed. The WEL bit is set to 1 with the WREN instruction. The WEL bit is reset to 0 after the following events: • Write Disable (WRDI) instruction completion • Write instructions (WRITE, WRSR, WRID, LID) completion including the write cycle time t W • Power-up BP1, BP0 bits The Block Protect bits (BP1, BP0) are non-volatile. BP1,BP0 bits define the size of the memory block to be protected against write instructions, as defined in Table 2. These bits are written with the Write Status Register (WRSR) instruction, provided that the Status Register is not protected (refer to “SRWD bit and W input signal”, on page 13). 12/43 DocID023103 Rev 8

M95128-A125 M95128-A145 Operating features Table 3. Write-protected block size Status Register bits Protected block Protected array addresses BP1 BP0 0 0 None None 0 1 Upper quarter 3000h-3FFFh 1 0 Upper half 2000h-3FFFh 1 1 Whole memory 0000h - 3FFFh plus Identification page SRWD bit and W input signal The Status Register Write Disable (SRWD) bit is operated in conjunction with the Write Protect pin (W) signal. When the SRWD bit is written to 0, it is possible to write the Status Register, regardless of whether the pin Write Protect (W) is driven high or low. When the SRWD bit is written to 1, two cases have to be considered, depending on the state of the W input pin: • Case 1: if pin W is driven high, it is possible to write the Status Register. • Case 2: if pin W is driven low, it is not possible to write the Status Register (WRSR is discarded) and therefore SRWD,BP1,BP0 bits cannot be changed (the size of the protected memory block defined by BP1,BP0 bits is frozen). Case 2 can be entered in either sequence: • Writing SRWD bit to 1 after driving pin W low, or • Driving pin W low after writing SRWD bit to 1. The only way to exit Case 2 is to pull pin W high. Note: if pin W is permanently tied high, the Status Register cannot be write-protected. The protection features of the device are summarized in Table 4. Table 4. Protection modes SRWD bit W signal Status 0 X Status Register is writable. 1 1 1 0 Status Register is write-protected. 3.5 Identification page The M95128-A125 and M95128-A145 offer an Identification page (64 byte) in addition to the 128 Kbit memory. The Identification page contains two fields: • Device identification: the three first byte are programmed by STMicroelectronics with the Device identification code, as shown in Table 5. • Application parameters: the bytes after the Device identification code are available for application specific data. DocID023103 Rev 8 13/43 42

Operating features M95128-A125 M95128-A145 Note: If the end application does not need to read the Device identification code, this field can be overwritten and used to store application-specific data. Once the application-specific data are written in the Identification page, the whole Identification page should be permanently locked in Read-only mode. The Read, Write, Lock Identification Page instructions are detailed in Section 4: Instructions. Table 5. Device identification bytes Address in Content Value Identification page 00h ST Manufacturer code 20h 01h SPI Family code 00h 02h Memory Density code 0Eh (128 Kbit) 14/43 DocID023103 Rev 8

M95128-A125 M95128-A145 Instructions 4 Instructions Each command is composed of bytes (MSBit transmitted first), initiated with the instruction byte, as summarized in Table 6. If an invalid instruction is sent (one not contained in Table 6), the device automatically enters a Wait state until deselected. Table 6. Instruction set Instruction Instruction Description format WREN Write Enable 0000 0110 WRDI Write Disable 0000 0100 RDSR Read Status Register 0000 0101 WRSR Write Status Register 0000 0001 READ Read from Memory Array 0000 0011 WRITE Write to Memory Array 0000 0010 RDID Read Identification Page 1000 0011 WRID Write Identification Page 1000 0010 RDLS Reads the Identification Page lock status. 1000 0011 LID Locks the Identification page in read-only mode. 1000 0010 For read and write commands to memory array and Identification Page, the address is defined by two bytes as explained in Table 7. Table 7. Significant bits within the two address bytes(1) MSB Address byte LSB Address byte Instructions b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0 READ or x x A13 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 WRITE RDID or 0 0 0 0 0 0 0 0 0 0 A5 A4 A3 A2 A1 A0 WRID RDLS or 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 LID 1. A: Significant address bit. DocID023103 Rev 8 15/43 42

Instructions M95128-A125 M95128-A145 4.1 Write Enable (WREN) The WREN instruction must be decoded by the device before a write instruction (WRITE, WRSR, WRID or LID). As shown in Figure 5, to send this instruction to the device, Chip Select (S) is driven low, the bits of the instruction byte are shifted in (MSB first) on Serial Data Input (D) after what the Chip Select (S) input is driven high and the WEL bit is set (Status Register bit). Figure 5. Write Enable (WREN) sequence (cid:94) (cid:1004) (cid:1005) (cid:1006) (cid:1007) (cid:1008) (cid:1009) (cid:1010) (cid:1011) (cid:18) (cid:47)(cid:374)(cid:400)(cid:410)(cid:396)(cid:437)(cid:272)(cid:410)(cid:349)(cid:381)(cid:374) (cid:24) (cid:44)(cid:349)(cid:336)(cid:346)(cid:3)(cid:47)(cid:373)(cid:393)(cid:286)(cid:282)(cid:258)(cid:374)(cid:272)(cid:286) (cid:89) (cid:68)(cid:76)(cid:89)(cid:19)(cid:21)(cid:21)(cid:27)(cid:20)(cid:74) 4.2 Write Disable (WRDI) One way of resetting the WEL bit (in the Status Register) is to send a Write Disable instruction to the device. As shown in Figure 6, to send this instruction to the device, Chip Select (S) is driven low, and the bits of the instruction byte are shifted in (MSB first), on Serial Data Input (D), after what the Chip Select (S) input is driven high and the WEL bit is reset (Status Register bit). If a Write cycle is currently in progress, the WRDI instruction is decoded and executed and the WEL bit is reset to 0 with no effect on the ongoing Write cycle. Figure 6. Write Disable (WRDI) sequence (cid:51) (cid:16) (cid:17) (cid:18) (cid:19) (cid:20) (cid:21) (cid:22) (cid:23) (cid:35) (cid:41)(cid:78)(cid:83)(cid:84)(cid:82)(cid:85)(cid:67)(cid:84)(cid:73)(cid:79)(cid:78) (cid:36) (cid:40)(cid:73)(cid:71)(cid:72)(cid:0)(cid:41)(cid:77)(cid:80)(cid:69)(cid:68)(cid:65)(cid:78)(cid:67)(cid:69) (cid:49) (cid:33)(cid:41)(cid:16)(cid:19)(cid:23)(cid:21)(cid:16)(cid:68)(cid:0)(cid:0)(cid:0) 16/43 DocID023103 Rev 8

M95128-A125 M95128-A145 Instructions 4.3 Read Status Register (RDSR) The Read Status Register (RDSR) instruction is used to read the content of the Status Register. As shown in Figure 7, to send this instruction to the device, Chip Select (S) is first driven low. The bits of the instruction byte are shifted in (MSB first) on Serial Data Input (D), the Status Register content is then shifted out (MSB first) on Serial Data Output (Q). If Chip Select (S) continues to be driven low, the Status Register content is continuously shifted out. The Status Register can always be read, even if a Write cycle (t ) is in progress. The Status W Register functionality is detailed in Section 3.4.2: Status Register and data protection. Figure 7. Read Status Register (RDSR) sequence (cid:51) (cid:16) (cid:17) (cid:18) (cid:19) (cid:20) (cid:21) (cid:22) (cid:23) (cid:24) (cid:25) (cid:17)(cid:16) (cid:17)(cid:17) (cid:17)(cid:18) (cid:17)(cid:19) (cid:17)(cid:20) (cid:17)(cid:21) (cid:35) (cid:41)(cid:78)(cid:83)(cid:84)(cid:82)(cid:85)(cid:67)(cid:84)(cid:73)(cid:79)(cid:78) (cid:36) (cid:51)(cid:84)(cid:65)(cid:84)(cid:85)(cid:83)(cid:0)(cid:50)(cid:69)(cid:71)(cid:73)(cid:83)(cid:84)(cid:69)(cid:82)(cid:0)(cid:47)(cid:85)(cid:84) (cid:51)(cid:84)(cid:65)(cid:84)(cid:85)(cid:83)(cid:0)(cid:50)(cid:69)(cid:71)(cid:73)(cid:83)(cid:84)(cid:69)(cid:82)(cid:0)(cid:47)(cid:85)(cid:84) (cid:40)(cid:73)(cid:71)(cid:72)(cid:0)(cid:41)(cid:77)(cid:80)(cid:69)(cid:68)(cid:65)(cid:78)(cid:67)(cid:69) (cid:49) (cid:23) (cid:22) (cid:21) (cid:20) (cid:19) (cid:18) (cid:17) (cid:16) (cid:23) (cid:22) (cid:21) (cid:20) (cid:19) (cid:18) (cid:17) (cid:16) (cid:23) (cid:45)(cid:51)(cid:34) (cid:45)(cid:51)(cid:34) (cid:33)(cid:41)(cid:16)(cid:18)(cid:16)(cid:19)(cid:17)(cid:37) DocID023103 Rev 8 17/43 42

Instructions M95128-A125 M95128-A145 4.4 Write Status Register (WRSR) The Write Status Register (WRSR) instruction allows new values to be written to the Status Register. Before it can be accepted, a Write Enable (WREN) instruction must previously have been executed. The Write Status Register (WRSR) instruction is entered (MSB first) by driving Chip Select (S) low, sending the instruction code followed by the data byte on Serial Data input (D), and driving the Chip Select (S) signal high. The contents of the SRWD and BP1, BP0 bits are updated after the completion of the WRSR instruction, including the Write cycle (t ). W The Write Status Register (WRSR) instruction has no effect on the b6, b5, b4, b1 and b0 bits in the Status Register (see Table 2: Status Register format). The Status Register functionality is detailed in Section 3.4.2: Status Register and data protection. The instruction is not accepted, and is not executed, if a Write cycle is currently in progress. Figure 8. Write Status Register (WRSR) sequence (cid:51) (cid:16) (cid:17) (cid:18) (cid:19) (cid:20) (cid:21) (cid:22) (cid:23) (cid:24) (cid:25) (cid:17)(cid:16) (cid:17)(cid:17) (cid:17)(cid:18) (cid:17)(cid:19) (cid:17)(cid:20) (cid:17)(cid:21) (cid:35) (cid:41)(cid:78)(cid:83)(cid:84)(cid:82)(cid:85)(cid:67)(cid:84)(cid:73)(cid:79)(cid:78) (cid:51)(cid:84)(cid:65)(cid:84)(cid:85)(cid:83) (cid:50)(cid:69)(cid:71)(cid:73)(cid:83)(cid:84)(cid:69)(cid:82)(cid:0)(cid:41)(cid:78) (cid:36) (cid:23) (cid:22) (cid:21) (cid:20) (cid:19) (cid:18) (cid:17) (cid:16) (cid:40)(cid:73)(cid:71)(cid:72)(cid:0)(cid:41)(cid:77)(cid:80)(cid:69)(cid:68)(cid:65)(cid:78)(cid:67)(cid:69) (cid:45)(cid:51)(cid:34) (cid:49) (cid:33)(cid:41)(cid:16)(cid:18)(cid:18)(cid:24)(cid:18)(cid:68) 18/43 DocID023103 Rev 8

M95128-A125 M95128-A145 Instructions 4.5 Read from Memory Array (READ) The READ instruction is used to read the content of the memory. As shown in Figure 9, to send this instruction to the device, Chip Select (S) is first driven low. The bits of the instruction byte and address bytes are shifted in (MSB first) on Serial Data Input (D) and the addressed data byte is then shifted out (MSB first) on Serial Data Output (Q). The first addressed byte can be any byte within any page. If Chip Select (S) continues to be driven low, the internal address register is automatically incremented, and the next byte of data is shifted out. The whole memory can therefore be read with a single READ instruction. When the highest address is reached, the address counter rolls over to zero, allowing the Read cycle to be continued indefinitely. The Read cycle is terminated by driving Chip Select (S) high at any time when the data bits are shifted out on Serial Data Output (Q). The instruction is not accepted, and is not executed, if a Write cycle is currently in progress. Figure 9. Read from Memory Array (READ) sequence (cid:54) (cid:19) (cid:20) (cid:21) (cid:22) (cid:23) (cid:24) (cid:25) (cid:26) (cid:27) (cid:28) (cid:20)(cid:19) (cid:21)(cid:19) (cid:21)(cid:20) (cid:21)(cid:21) (cid:21)(cid:22) (cid:21)(cid:23) (cid:21)(cid:24) (cid:21)(cid:25) (cid:21)(cid:26) (cid:21)(cid:27) (cid:21)(cid:28) (cid:22)(cid:19) (cid:22)(cid:20) (cid:38) (cid:44)(cid:81)(cid:86)(cid:87)(cid:85)(cid:88)(cid:70)(cid:87)(cid:76)(cid:82)(cid:81) (cid:20)(cid:25)(cid:16)(cid:37)(cid:76)(cid:87)(cid:3)(cid:36)(cid:71)(cid:71)(cid:85)(cid:72)(cid:86)(cid:86) (cid:39) (cid:20)(cid:24) (cid:20)(cid:23) (cid:20)(cid:22) (cid:22) (cid:21) (cid:20) (cid:19) (cid:48)(cid:54)(cid:37) (cid:39)(cid:68)(cid:87)(cid:68)(cid:3)(cid:50)(cid:88)(cid:87)(cid:3)(cid:20) (cid:39)(cid:68)(cid:87)(cid:68)(cid:3)(cid:50)(cid:88)(cid:87)(cid:3)(cid:21) (cid:43)(cid:76)(cid:74)(cid:75)(cid:3)(cid:44)(cid:80)(cid:83)(cid:72)(cid:71)(cid:68)(cid:81)(cid:70)(cid:72) (cid:52) (cid:26) (cid:25) (cid:24) (cid:23) (cid:22) (cid:21) (cid:20) (cid:19) (cid:26) (cid:48)(cid:54)(cid:37) (cid:36)(cid:44)(cid:19)(cid:20)(cid:26)(cid:28)(cid:22)(cid:39) 1. Depending on the memory size, as shown in Table 7, the most significant address bits are Don’t Care. DocID023103 Rev 8 19/43 42

Instructions M95128-A125 M95128-A145 4.6 Write to Memory Array (WRITE) The WRITE instruction is used to write new data in the memory. As shown in Figure 10, to send this instruction to the device, Chip Select (S) is first driven low. The bits of the instruction byte, address bytes, and at least one data byte are then shifted in (MSB first), on Serial Data Input (D). The instruction is terminated by driving Chip Select (S) high at a data byte boundary. Figure 10 shows a single byte write. Figure 10. Byte Write (WRITE) sequence (cid:51) (cid:16) (cid:17) (cid:18) (cid:19) (cid:20) (cid:21) (cid:22) (cid:23) (cid:24) (cid:25) (cid:17)(cid:16) (cid:18)(cid:16) (cid:18)(cid:17) (cid:18)(cid:18) (cid:18)(cid:19) (cid:18)(cid:20) (cid:18)(cid:21) (cid:18)(cid:22) (cid:18)(cid:23) (cid:18)(cid:24) (cid:18)(cid:25) (cid:19)(cid:16) (cid:19)(cid:17) (cid:35) (cid:41)(cid:78)(cid:83)(cid:84)(cid:82)(cid:85)(cid:67)(cid:84)(cid:73)(cid:79)(cid:78) (cid:17)(cid:22)(cid:13)(cid:34)(cid:73)(cid:84)(cid:0)(cid:33)(cid:68)(cid:68)(cid:82)(cid:69)(cid:83)(cid:83) (cid:36)(cid:65)(cid:84)(cid:65)(cid:0)(cid:34)(cid:89)(cid:84)(cid:69) (cid:36) (cid:17)(cid:21) (cid:17)(cid:20) (cid:17)(cid:19) (cid:19) (cid:18) (cid:17) (cid:16) (cid:23) (cid:22) (cid:21) (cid:20) (cid:19) (cid:18) (cid:17) (cid:16) (cid:40)(cid:73)(cid:71)(cid:72)(cid:0)(cid:41)(cid:77)(cid:80)(cid:69)(cid:68)(cid:65)(cid:78)(cid:67)(cid:69) (cid:49) (cid:33)(cid:41)(cid:16)(cid:17)(cid:23)(cid:25)(cid:21)(cid:36) 1. Depending on the memory size, as shown in Table 7, the most significant address bits are Don’t Care. A Page write is used to write several bytes inside a page, with a single internal Write cycle. For a Page write, Chip Select (S) has to remain low, as shown in Figure 11, so that the next data bytes are shifted in. Each time a new data byte is shifted in, the least significant bits of the internal address counter are incremented. If the address counter exceeds the page boundary (the page size is 64 byte), the internal address pointer rolls over to the beginning of the same page where next data bytes will be written. If more than 64 byte are received, only the last 64 byte are written. For both Byte write and Page write, the self-timed Write cycle starts from the rising edge of Chip Select (S), and continues for a period t (as specified in Table 15). W The instruction is discarded, and is not executed, under the following conditions: • if a Write cycle is already in progress • if the addressed page is in the region protected by the Block Protect (BP1 and BP0) bits • if one of the conditions defined in Section 3.4.1 is not satisfied Note: The self-timed Write cycle t is internally executed as a sequence of two consecutive W events: [Erase addressed byte(s)], followed by [Program addressed byte(s)]. An erased bit is read as “0” and a programmed bit is read as “1”. 20/43 DocID023103 Rev 8

M95128-A125 M95128-A145 Instructions Figure 11. Page Write (WRITE) sequence (cid:54) (cid:19) (cid:20) (cid:21) (cid:22) (cid:23) (cid:24) (cid:25) (cid:26) (cid:27) (cid:28) (cid:20)(cid:19) (cid:21)(cid:19) (cid:21)(cid:20) (cid:21)(cid:21) (cid:21)(cid:22) (cid:21)(cid:23) (cid:21)(cid:24) (cid:21)(cid:25) (cid:21)(cid:26) (cid:21)(cid:27) (cid:21)(cid:28) (cid:22)(cid:19) (cid:22)(cid:20) (cid:38) (cid:44)(cid:81)(cid:86)(cid:87)(cid:85)(cid:88)(cid:70)(cid:87)(cid:76)(cid:82)(cid:81) (cid:20)(cid:25)(cid:16)(cid:37)(cid:76)(cid:87)(cid:3)(cid:36)(cid:71)(cid:71)(cid:85)(cid:72)(cid:86)(cid:86) (cid:39)(cid:68)(cid:87)(cid:68)(cid:3)(cid:37)(cid:92)(cid:87)(cid:72)(cid:3)(cid:20) (cid:39) (cid:20)(cid:24) (cid:20)(cid:23) (cid:20)(cid:22) (cid:22) (cid:21) (cid:20) (cid:19) (cid:26) (cid:25) (cid:24) (cid:23) (cid:22) (cid:21) (cid:20) (cid:19) (cid:48)(cid:54)(cid:37) (cid:48)(cid:54)(cid:37) (cid:54) (cid:22)(cid:21) (cid:22)(cid:22) (cid:22)(cid:23) (cid:22)(cid:24) (cid:22)(cid:25) (cid:22)(cid:26) (cid:22)(cid:27) (cid:22)(cid:28) (cid:23)(cid:19) (cid:23)(cid:20) (cid:23)(cid:21) (cid:23)(cid:22) (cid:23)(cid:23) (cid:23)(cid:24) (cid:23)(cid:25) (cid:23)(cid:26) (cid:38) (cid:39)(cid:68)(cid:87)(cid:68)(cid:3)(cid:37)(cid:92)(cid:87)(cid:72)(cid:3)(cid:21) (cid:39)(cid:68)(cid:87)(cid:68)(cid:3)(cid:37)(cid:92)(cid:87)(cid:72)(cid:3)(cid:22) (cid:39)(cid:68)(cid:87)(cid:68)(cid:3)(cid:37)(cid:92)(cid:87)(cid:72)(cid:3)(cid:49) (cid:39) (cid:26) (cid:25) (cid:24) (cid:23) (cid:22) (cid:21) (cid:20) (cid:19) (cid:26) (cid:25) (cid:24) (cid:23) (cid:22) (cid:21) (cid:20) (cid:19) (cid:25) (cid:24) (cid:23) (cid:22) (cid:21) (cid:20) (cid:19) (cid:48)(cid:54)(cid:37) (cid:48)(cid:54)(cid:37) (cid:36)(cid:44)(cid:19)(cid:20)(cid:26)(cid:28)(cid:25)(cid:72) 1. Depending on the memory size, as shown in Table 7, the most significant address bits are Don’t Care. DocID023103 Rev 8 21/43 42

Instructions M95128-A125 M95128-A145 4.7 Read Identification Page (RDID) The Read Identification Page instruction is used to read the Identification Page (additional page of 64 byte which can be written and later permanently locked in Read-only mode). The Chip Select (S) signal is first driven low, the bits of the instruction byte and address bytes are then shifted in (MSB first) on Serial Data input (D). Address bit A10 must be 0 and the other upper address bits are Don't Care (it might be easier to define these bits as 0, as shown in Table 7). The data byte pointed to by the lower address bits [A5:A0] is shifted out (MSB first) on Serial Data output (Q). The first byte addressed can be any byte within the identification page. If Chip Select (S) continues to be driven low, the internal address register is automatically incremented and the byte of data at the new address is shifted out. Note that there is no roll over feature in the Identification Page. The address of bytes to read must not exceed the page boundary. The read cycle is terminated by driving Chip Select (S) high. The rising edge of the Chip Select (S) signal can occur at any time when the data bits are shifted out. The instruction is not accepted, and is not executed, if a Write cycle is currently in progress. Figure 12. Read Identification Page sequence (cid:54) (cid:19) (cid:20) (cid:21) (cid:22) (cid:23) (cid:24) (cid:25) (cid:26) (cid:27) (cid:28) (cid:20)(cid:19) (cid:21)(cid:19) (cid:21)(cid:20) (cid:21)(cid:21) (cid:21)(cid:22) (cid:21)(cid:23) (cid:21)(cid:24) (cid:21)(cid:25) (cid:21)(cid:26) (cid:21)(cid:27) (cid:21)(cid:28) (cid:22)(cid:19) (cid:22)(cid:20) (cid:38) (cid:44)(cid:81)(cid:86)(cid:87)(cid:85)(cid:88)(cid:70)(cid:87)(cid:76)(cid:82)(cid:81) (cid:20)(cid:25)(cid:16)(cid:69)(cid:76)(cid:87)(cid:3)(cid:68)(cid:71)(cid:71)(cid:85)(cid:72)(cid:86)(cid:86) (cid:39) (cid:20)(cid:24) (cid:20)(cid:23) (cid:20)(cid:22) (cid:22) (cid:21) (cid:20) (cid:19) (cid:48)(cid:54)(cid:37) (cid:39)(cid:68)(cid:87)(cid:68)(cid:3)(cid:50)(cid:88)(cid:87)(cid:3)(cid:20) (cid:39)(cid:68)(cid:87)(cid:68)(cid:3)(cid:50)(cid:88)(cid:87)(cid:3)(cid:21) (cid:43)(cid:76)(cid:74)(cid:75)(cid:3)(cid:76)(cid:80)(cid:83)(cid:72)(cid:71)(cid:68)(cid:81)(cid:70)(cid:72) (cid:52) (cid:26) (cid:25) (cid:24) (cid:23) (cid:22) (cid:21) (cid:20) (cid:19) (cid:26) (cid:48)(cid:54)(cid:37) (cid:36)(cid:76)(cid:20)(cid:24)(cid:28)(cid:25)(cid:25) The first three bytes of the Identification page offer information about the device itself. Please refer to Section 3.5: Identification page for more information. 22/43 DocID023103 Rev 8

M95128-A125 M95128-A145 Instructions 4.8 Write Identification Page (WRID) The Write Identification Page instruction is used to write the Identification Page (additional page of 64 byte which can also be permanently locked in Read-only mode). The Chip Select signal (S) is first driven low, and then the bits of the instruction byte, address bytes, and at least one data byte are shifted in (MSB first) on Serial Data input (D). Address bit A10 must be 0 and the other upper address bits are Don't Care (it might be easier to define these bits as 0, as shown in Table 7). The lower address bits [A5:A0] define the byte address inside the identification page. The self-timed Write cycle starts from the rising edge of Chip Select (S), and continues for a period t (as specified in Table 15). W Figure 13. Write Identification Page sequence (cid:54) (cid:19) (cid:20) (cid:21) (cid:22) (cid:23) (cid:24) (cid:25) (cid:26) (cid:27) (cid:28) (cid:20)(cid:19) (cid:21)(cid:19) (cid:21)(cid:20) (cid:21)(cid:21) (cid:21)(cid:22) (cid:21)(cid:23) (cid:21)(cid:24) (cid:21)(cid:25) (cid:21)(cid:26) (cid:21)(cid:27) (cid:21)(cid:28) (cid:22)(cid:19) (cid:22)(cid:20) (cid:38) (cid:44)(cid:81)(cid:86)(cid:87)(cid:85)(cid:88)(cid:70)(cid:87)(cid:76)(cid:82)(cid:81) (cid:20)(cid:25)(cid:16)(cid:69)(cid:76)(cid:87)(cid:3)(cid:68)(cid:71)(cid:71)(cid:85)(cid:72)(cid:86)(cid:86) (cid:39)(cid:68)(cid:87)(cid:68)(cid:3)(cid:69)(cid:92)(cid:87)(cid:72) (cid:39) (cid:20)(cid:24) (cid:20)(cid:23) (cid:20)(cid:22) (cid:22) (cid:21) (cid:20) (cid:19) (cid:26) (cid:25) (cid:24) (cid:23) (cid:22) (cid:21) (cid:20) (cid:19) (cid:43)(cid:76)(cid:74)(cid:75)(cid:3)(cid:76)(cid:80)(cid:83)(cid:72)(cid:71)(cid:68)(cid:81)(cid:70)(cid:72) (cid:52) (cid:36)(cid:76)(cid:20)(cid:24)(cid:28)(cid:25)(cid:26) Note: The first three bytes of the Identification page offer the Device Identification code (Please refer to Section 3.5: Identification page for more information). Using the WRID command on these first three bytes overwrites the Device Identification code. The instruction is discarded, and is not executed, under the following conditions: • If a Write cycle is already in progress • If the Block Protect bits (BP1,BP0) = (1,1) • If one of the conditions defined in Section 3.4.1: Protocol control is not satisfied. 4.9 Read Lock Status (RDLS) The Read Lock Status instruction is used to read the lock status. To send this instruction to the device, Chip Select (S) first has to be driven low. The bits of the instruction byte and address bytes are then shifted in (MSB first) on Serial Data input (D). Address bit A10 must be 1; all other address bits are Don't Care (it might be easier to define these bits as 0, as shown in Table 7). The Lock bit is the LSB (Least Significant Bit) of the byte read on Serial Data output (Q). It is at ‘1’ when the lock is active and at ‘0’ when the lock is not active. If Chip Select (S) continues to be driven low, the same data byte is shifted out. The read cycle is terminated by driving Chip Select (S) high. The instruction sequence is shown in Figure 14. DocID023103 Rev 8 23/43 42

Instructions M95128-A125 M95128-A145 The Read Lock Status instruction is not accepted and not executed if a Write cycle is currently in progress. Figure 14. Read Lock Status sequence (cid:54) (cid:19) (cid:20) (cid:21) (cid:22) (cid:23) (cid:24) (cid:25) (cid:26) (cid:27) (cid:28) (cid:20)(cid:19) (cid:21)(cid:19) (cid:21)(cid:20) (cid:21)(cid:21) (cid:21)(cid:22) (cid:21)(cid:23) (cid:21)(cid:24) (cid:21)(cid:25) (cid:21)(cid:26) (cid:21)(cid:27) (cid:21)(cid:28) (cid:22)(cid:19) (cid:22)(cid:20) (cid:38) (cid:44)(cid:81)(cid:86)(cid:87)(cid:85)(cid:88)(cid:70)(cid:87)(cid:76)(cid:82)(cid:81) (cid:20)(cid:25)(cid:16)(cid:69)(cid:76)(cid:87)(cid:3)(cid:68)(cid:71)(cid:71)(cid:85)(cid:72)(cid:86)(cid:86) (cid:39) (cid:20)(cid:24) (cid:20)(cid:23) (cid:20)(cid:22) (cid:22) (cid:21) (cid:20) (cid:19) (cid:48)(cid:54)(cid:37) (cid:39)(cid:68)(cid:87)(cid:68)(cid:3)(cid:50)(cid:88)(cid:87)(cid:3)(cid:20) (cid:39)(cid:68)(cid:87)(cid:68)(cid:3)(cid:50)(cid:88)(cid:87)(cid:3)(cid:21) (cid:43)(cid:76)(cid:74)(cid:75)(cid:3)(cid:76)(cid:80)(cid:83)(cid:72)(cid:71)(cid:68)(cid:81)(cid:70)(cid:72) (cid:52) (cid:26) (cid:25) (cid:24) (cid:23) (cid:22) (cid:21) (cid:20) (cid:19) (cid:26) (cid:48)(cid:54)(cid:37) (cid:36)(cid:76)(cid:20)(cid:24)(cid:28)(cid:25)(cid:25) 4.10 Lock Identification Page (LID) The Lock Identification Page (LID) command is used to permanently lock the Identification Page in Read-only mode. The LID instruction is issued by driving Chip Select (S) low, sending (MSB first) the instruction code, the address and a data byte on Serial Data input (D), and driving Chip Select (S) high. In the address sent, A10 must be equal to 1. All other address bits are Don't Care (it might be easier to define these bits as 0, as shown in Table 7). The data byte sent must be equal to the binary value xxxx xx1x, where x = Don't Care. The LID instruction is terminated by driving Chip Select (S) high at a data byte boundary, otherwise, the instruction is not executed. Figure 15. Lock ID sequence (cid:54) (cid:19) (cid:20) (cid:21) (cid:22) (cid:23) (cid:24) (cid:25) (cid:26) (cid:27) (cid:28) (cid:20)(cid:19) (cid:21)(cid:19) (cid:21)(cid:20) (cid:21)(cid:21) (cid:21)(cid:22) (cid:21)(cid:23) (cid:21)(cid:24) (cid:21)(cid:25) (cid:21)(cid:26) (cid:21)(cid:27) (cid:21)(cid:28) (cid:22)(cid:19) (cid:22)(cid:20) (cid:38) (cid:44)(cid:81)(cid:86)(cid:87)(cid:85)(cid:88)(cid:70)(cid:87)(cid:76)(cid:82)(cid:81) (cid:20)(cid:25)(cid:16)(cid:69)(cid:76)(cid:87)(cid:3)(cid:68)(cid:71)(cid:71)(cid:85)(cid:72)(cid:86)(cid:86) (cid:39)(cid:68)(cid:87)(cid:68)(cid:3)(cid:69)(cid:92)(cid:87)(cid:72) (cid:39) (cid:20)(cid:24) (cid:20)(cid:23) (cid:20)(cid:22) (cid:22) (cid:21) (cid:20) (cid:19) (cid:26) (cid:25) (cid:24) (cid:23) (cid:22) (cid:21) (cid:20) (cid:19) (cid:43)(cid:76)(cid:74)(cid:75)(cid:3)(cid:76)(cid:80)(cid:83)(cid:72)(cid:71)(cid:68)(cid:81)(cid:70)(cid:72) (cid:52) (cid:36)(cid:76)(cid:20)(cid:24)(cid:28)(cid:25)(cid:26) Driving Chip Select (S) high at a byte boundary of the input data triggers the self-timed Write cycle which duration is t (specified in Table 15). The instruction sequence is shown in W Figure 15. 24/43 DocID023103 Rev 8

M95128-A125 M95128-A145 Instructions The instruction is discarded, and is not executed, under the following conditions: • If a Write cycle is already in progress • If the Block Protect bits (BP1,BP0) = (1,1) • If one of the conditions defined in Section 3.4.1: Protocol control is not satisfied. DocID023103 Rev 8 25/43 42

Application design recommendations M95128-A125 M95128-A145 5 Application design recommendations 5.1 Supply voltage (V ) CC 5.1.1 Operating supply voltage (V ) CC Prior to selecting the memory and issuing instructions to it, a valid and stable V voltage CC within the specified [V , V ] range must be applied (see Table 10 and Table 11). CC(min) CC(max) This voltage must remain stable and valid until the end of the transmission of the instruction and, for a Write instruction, until the completion of the internal Write cycle (t ). In order to W secure a stable DC supply voltage, it is recommended to decouple the V line with a CC suitable capacitor (usually of the order of 10 nF to 100 nF) close to the V /V package CC SS pins. 5.1.2 Power-up conditions When the power supply is turned on, V continuously rises from V to V . During this CC SS CC time, the Chip Select (S) line is not allowed to float but should follow the V voltage. It is CC therefore recommended to connect the S line to V via a suitable pull-up resistor (see CC Figure 16). The V voltage has to rise continuously from 0 V up to the minimum V operating voltage CC CC defined in Table 13 and Table 14. In order to prevent inadvertent write operations during power-up, a power-on-reset (POR) circuit is included. At power-up, the device does not respond to any instruction until V reaches the internal CC threshold voltage (this threshold is defined in the DC characteristics tables 13 and 14 as VRES). When V passes over the POR threshold, the device is reset and in the following state: CC • in the Standby power mode • deselected • Status register values: – Write Enable Latch (WEL) bit is reset to 0. – Write In Progress (WIP) bit is reset to 0. – SRWD, BP1 and BP0 bits remain unchanged (non-volatile bits). • not in the Hold condition As soon as the V voltage has reached a stable value within [V (min), V (max)] range, CC CC CC the device is ready for operation. 26/43 DocID023103 Rev 8

M95128-A125 M95128-A145 Application design recommendations 5.1.3 Power-down During power-down (continuous decrease in the V supply voltage below the minimum CC V operating voltage defined in Table 13 and Table 14), the device must be: CC • deselected (Chip Select (S) should be allowed to follow the voltage applied on V ), CC • in Standby power mode (there should not be any internal Write cycle in progress). 5.2 Implementing devices on SPI bus Figure 16 shows an example of three devices, connected to the SPI bus master. Only one device is selected at a time, so that only the selected device drives the Serial Data output (Q) line. All the other devices outputs are then in high impedance. Figure 16. Bus master and memory devices on the SPI bus (cid:54) (cid:35)(cid:35) (cid:51)(cid:36)(cid:47) (cid:51)(cid:48)(cid:41)(cid:0)(cid:73)(cid:78)(cid:84)(cid:69)(cid:82)(cid:70)(cid:65)(cid:67)(cid:69)(cid:0)(cid:87)(cid:73)(cid:84)(cid:72) (cid:51)(cid:36)(cid:41) (cid:8)(cid:35)(cid:48)(cid:47)(cid:44)(cid:12)(cid:0)(cid:35)(cid:48)(cid:40)(cid:33)(cid:9)(cid:0)(cid:29) (cid:8)(cid:16)(cid:12)(cid:0)(cid:16)(cid:9)(cid:0)(cid:79)(cid:82)(cid:0)(cid:8)(cid:17)(cid:12)(cid:0)(cid:17)(cid:9) (cid:51)(cid:35)(cid:43) (cid:35) (cid:49) (cid:36) (cid:54)(cid:35)(cid:35) (cid:35) (cid:49) (cid:36) (cid:54)(cid:35)(cid:35) (cid:35) (cid:49) (cid:36) (cid:54)(cid:35)(cid:35) (cid:51)(cid:48)(cid:41)(cid:0)(cid:66)(cid:85)(cid:83)(cid:0)(cid:77)(cid:65)(cid:83)(cid:84)(cid:69)(cid:82) (cid:51)(cid:48)(cid:41)(cid:0)(cid:77)(cid:69)(cid:77)(cid:79)(cid:82)(cid:89) (cid:51)(cid:48)(cid:41)(cid:0)(cid:77)(cid:69)(cid:77)(cid:79)(cid:82)(cid:89) (cid:51)(cid:48)(cid:41)(cid:0)(cid:77)(cid:69)(cid:77)(cid:79)(cid:82)(cid:89) (cid:50) (cid:50) (cid:50) (cid:68)(cid:69)(cid:86)(cid:73)(cid:67)(cid:69) (cid:68)(cid:69)(cid:86)(cid:73)(cid:67)(cid:69) (cid:68)(cid:69)(cid:86)(cid:73)(cid:67)(cid:69) (cid:35)(cid:51)(cid:19) (cid:35)(cid:51)(cid:18) (cid:35)(cid:51)(cid:17) (cid:51) (cid:55) (cid:40)(cid:47)(cid:44)(cid:36) (cid:51) (cid:55) (cid:40)(cid:47)(cid:44)(cid:36) (cid:51) (cid:55) (cid:40)(cid:47)(cid:44)(cid:36) (cid:54) (cid:51)(cid:51) (cid:45)(cid:51)(cid:17)(cid:25)(cid:23)(cid:21)(cid:21)(cid:54)(cid:18) 1. The Write Protect (W) and Hold (HOLD) signals must be driven high or low as appropriate. A pull-up resistor connected on each /S input (represented in Figure 16) ensures that each device is not selected if the bus master leaves the /S line in the high impedance state. DocID023103 Rev 8 27/43 42

Application design recommendations M95128-A125 M95128-A145 5.3 Cycling with Error Correction Code (ECC) The Error Correction Code (ECC) is an internal logic function which is transparent for the SPI communication protocol. The ECC logic is implemented on each group of four EEPROM bytes(a). Inside a group, if a single bit out of the four bytes happens to be erroneous during a Read operation, the ECC detects this bit and replaces it with the correct value. The read reliability is therefore much improved. Even if the ECC function is performed on groups of four bytes, a single byte can be written/cycled independently. In this case, the ECC function also writes/cycles the three other bytes located in the same group(a). As a consequence, the maximum cycling budget is defined at group level and the cycling can be distributed over the 4 bytes of the group: the sum of the cycles seen by byte0, byte1, byte2 and byte3 of the same group must remain below the maximum value defined in Table 9: Cycling performance by groups of 4 byte. Example1: maximum cycling limit reached with 1 million cycles per byte Each byte of a group can be equally cycled 1 million times (at 25 °C) so that the group cycling budget is 4 million cycles. Example2: maximum cycling limit reached with unequal byte cycling Inside a group, byte0 can be cycled 2 million times, byte1 can be cycled 1 million times, byte2 and byte3 can be cycled 500,000 times, so that the group cycling budget is 4 million cycles. a. A group of four bytes is located at addresses [4*N, 4*N+1, 4*N+2, 4*N+3], where N is an integer. 28/43 DocID023103 Rev 8

M95128-A125 M95128-A145 Delivery state 6 Delivery state The device is delivered with: • the memory array set to all 1s (each byte = FFh), • Status register: bit SRWD =0, BP1 =0 and BP0 =0, • Identification page: the first three bytes define the Device identification code (value defined in Table 5). The content of the following bytes is Don’t Care. 7 Absolute maximum ratings Stressing the device outside the ratings listed in Table 8 may cause permanent damage to the device. These are stress ratings only, and operation of the device at these, or any other conditions outside those indicated in the operating sections of this specification, is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Table 8. Absolute maximum ratings Symbol Parameter Min. Max. Unit T Storage temperature –65 150 °C STG T Ambient operating temperature –40 150 °C AMR T Lead temperature during soldering See note (1) °C LEAD V Voltage on Q pin –0.50 V +0.6 V O CC V Input voltage –0.50 6.5 V I I DC output current (Q = 0) - 5 mA OL I DC output current (Q = 1) - 5 mA OH V Supply voltage –0.50 6.5 V CC V Electrostatic pulse (Human Body Model)(2) - 4000 V ESD 1. Compliant with JEDEC Std J-STD-020D (for small body, Sn-Pb or Pb-free assembly), the ST ECOPACK® 7191395 specification, and the European directive on Restrictions of Hazardous Substances (RoHS directive 2011/65/EU of July 2011). 2. Positive and negative pulses applied on pin pairs, in accordance with AEC-Q100-002 (compliant with ANSI/ESDA/JEDEC JS-001-2012, C1=100 pF, R1=1500 Ω, R2=500 Ω) DocID023103 Rev 8 29/43 42

DC and AC parameters M95128-A125 M95128-A145 8 DC and AC parameters This section summarizes the operating conditions and the DC/AC characteristics of the device. Table 9. Cycling performance by groups of 4 byte Symbol Parameter Test condition Min. Max. Unit TA ≤ 25 °C, 1.7 V < V < 5.5 V - 4,000,000 CC Ncycle Write cycle endurance(1) TA = 85 °C, 1.7 V < VCC < 5.5 V - 1,200,000 Write TA = 125 °C, 1.7 V < V < 5.5 V - 600,000 cycle(2) CC TA = 145 °C(3), 2.5 V < V < 5.5 V - 400,000 CC 1. The Write cycle endurance is defined for groups of four data bytes located at addresses [4*N, 4*N+1, 4*N+2, 4*N+3] where N is an integer, or for the status register byte (refer also to Section 5.3: Cycling with Error Correction Code (ECC)). The Write cycle endurance is defined by characterization and qualification. 2. A Write cycle is executed when either a Page Write, a Byte Write, a WRSR, a WRID or an LID instruction is decoded. When using the Byte Write, the Page Write or the WRID, refer also to Section 5.3: Cycling with Error Correction Code (ECC). 3. For temperature range 4 only. Table 10. Operating conditions (voltage range W, temperature range 4) Symbol Parameter Conditions Min. Max. Unit V Supply voltage - 2.5 5.5 V CC T Ambient operating temperature - –40 145 °C A 5.5 V ≥ V ≥ 2.5 V, f Operating clock frequency CC - 10 MHz C capacitive load on Q pin ≤ 100pF Table 11. Operating conditions (voltage range R, temperature range 3) Symbol Parameter Conditions Min. Max. Unit V Supply voltage - 1.7 5.5 V CC T Ambient operating temperature - –40 125 °C A V ≥ 2.5 V, capacitive load on Q pin ≤ 100pF - 10 CC f Operating clock frequency MHz C V ≥ 1.7 V, capacitive load on Q pin ≤ 100pF - 5 CC Table 12. Operating conditions (voltage range R, temperature range 3) for high-speed communications Symbol Parameter Conditions Min. Max. Unit V Supply voltage - 4.5 5.5 V CC T Ambient operating temperature - –40 85 °C A f Operating clock frequency V ≥ 4.5 V, capacitive load on Q pin ≤ 60 pF - 20 MHz C CC 30/43 DocID023103 Rev 8

M95128-A125 M95128-A145 DC and AC parameters Table 13. DC characteristics (voltage range W, temperature range 4) Specific test conditions Symbol Parameter (in addition to conditions specified in Min. Max. Unit Table 10) C (2) Output capacitance (Q) V = 0 V - 8 OUT OUT pF C (2) Input capacitance V = 0 V - 6 IN IN I Input leakage current V = V orV - 2 LI IN SS CC µA I Output leakage current S = V , V = V orV - 3 LO CC OUT SS CC V = 2.5 V, f = 10 MHz, CC C - 2 C = 0.1 V /0.9 V Q = open CC CC, I Supply current (Read) CC V = 5.5 V, f = 10 MHz, CC C - 4 mA C = 0.1 V /0.9 V Q = open CC CC, 2.5 V < V < 5.5 V, during t , I (1) Supply current (Write) CC W - 2(2) CC0 S = V CC t° = 85 °C, V = 2.5 V, S = V CC CC - 2 V = V or V IN SS CC t° = 85 °C, V = 5.5 V, S = V CC CC - 3 V = V or V IN SS CC t° = 125 °C, V = 2.5 V, S = V CC CC - 15 Supply current VIN = VSS or VCC I µA CC1 (Standby power mode) t° = 125 °C, V = 5.5 V, S = V CC CC - 20 V = V or V IN SS CC t° = 145 °C, V = 2.5 V, S = V CC CC - 25 V = V or V IN SS CC t° = 145 °C, V = 5.5 V, S = V CC CC - 40 V = V or V IN SS CC V Input low voltage - –0.45 0.3 V IL CC V Input high voltage - 0.7 V V +1 IH CC CC V Output low voltage I = 2 mA - 0.4 OL OL V V Output high voltage I = –2 mA 0.8 V - OH OH CC Internal reset threshold V (2) - 0.5 1.5 RES voltage 1. Average value during the Write cycle (t ) W 2. Characterized only, not 100% tested DocID023103 Rev 8 31/43 42

DC and AC parameters M95128-A125 M95128-A145 Table 14. DC characteristics (voltage range R, temperature range 3) Test conditions Symbol Parameter (in addition to conditions specified Min. Max. Unit in Table 11) C (3) Output capacitance (Q) V = 0 V - 8 OUT OUT pF C (3) Input capacitance V = 0 V - 6 IN IN I Input leakage current V = V orV - 2 LI IN SS CC µA I Output leakage current S = V , V = V orV - 3 LO CC OUT SS CC V = 1.7 V, C = 0.1 V /0.9 V , CC CC CC - 2 Q = open, f = 5 MHz C V = 2.5 V, C = 0.1 V /0.9 V , I Supply current (Read) CC CC CC - 2 mA CC Q = open, f = 10 MHz C V = 5.5 V, f = 20 MHz(1) CC C - 5 C = 0.1 V /0.9 V , Q = open CC CC 1.7 V ≤ V < 5.5 V during t , I (2) Supply current (Write) CC W - 2(3) mA CC0 S = V CC t° = 85 °C, V = 1.7 V, CC - 1 S = V V = V or V CC, IN SS CC t° = 85 °C, V = 2.5 V, CC - 2 S = V V = V or V CC, IN SS CC t° = 85 °C, V = 5.5 V, CC - 3 S = V V = V or V CC, IN SS CC I Supply current (Standby mode) µA CC1 t° = 125 °C, V = 1.7 V, CC - 15 S = V V = V or V CC, IN SS CC t° = 125 °C, V = 2.5 V, CC - 15 S = V V = V or V CC, IN SS CC t° = 125 °C, V = 5.5 V, CC - 20 S = V V = V or V CC, IN SS CC 1.7 V ≤ V < 2.5 V –0.45 0.25 V CC CC V Input low voltage V IL 2.5 V ≤ V < 5.5 V –0.45 0.3 V CC CC 1.7 V ≤ V < 2.5 V 0.75 V V + 1 CC CC CC V Input high voltage V IH 2.5 V ≤ V < 5.5 V 0.7 V V + 1 CC CC CC V = 1.7 V, I = 1 mA - 0.3 CC OL V Output low voltage V OL V ≥ 2.5 V, I = 2 mA - 0.4 CC OL V = 1.7 V, I = 1 mA 0.8 V - CC OH CC V Output high voltage V OH V ≥ 2.5 V, I = -2 mA 0.8 V - CC OH CC V (3) Internal reset threshold voltage - 0.5 1.5 V RES 1. When –40 °C < t° < 85 °C. 2. Average value during the Write cycle (t ) W 3. Characterized only, not 100% tested 32/43 DocID023103 Rev 8

M95128-A125 M95128-A145 DC and AC parameters Table 15. AC characteristics Min. Max. Min. Max. Min. Max. Test Test conditions Test Symbol Alt. Parameter Unit conditions specified in conditions specified in Table 10 specified in Table 11 and Table 12 Table 11 f f Clock frequency - 5 - 10 - 20 MHz C SCK t t S active setup time 60 - 30 - 15 - SLCH CSS1 t t S not active setup time 60 - 30 - 15 - SHCH CSS2 t t S deselect time 90 - 40 - 20 - SHSL CS t t S active hold time 60 - 30 - 15 - ns CHSH CSH t S not active hold time 60 - 30 - 15 - CHSL t (1) t Clock high time 80 - 40 - 20 - CH CLH t (1) t Clock low time 80 - 40 - 20 - CL CLL t (2) t Clock rise time - 2 - 2 - 2 CLCH RC µs t (2) t Clock fall time - 2 - 2 - 2 CHCL FC t t Data in setup time 20 - 10 - 5 - DVCH DSU t t Data in hold time 20 - 10 - 10 - CHDX DH t Clock low hold time after HOLD not active 60 - 30 - 15 - HHCH t Clock low hold time after HOLD active 60 - 30 - 15 - HLCH t Clock low set-up time before HOLD active 0 - 0 - 0 - CLHL Clock low set-up time before HOLD not t 0 - 0 - 0 - CLHH active ns t (2) t Output disable time - 80 - 40 - 20 SHQZ DIS t (3) t Clock low to output valid - 80 - 40 - 20 CLQV V t t Output hold time 0 - 0 - 0 - CLQX HO t (2) t Output rise time - 20 - 20 - 20 QLQH RO t (2) t Output fall time - 20 - 20 - 20 QHQL FO t t HOLD high to output valid - 80 - 40 - 20 HHQV LZ t (2) t HOLD low to output high-Z - 80 - 40 - 20 HLQZ HZ t t Write time - 4 - 4 - 4 ms W WC 1. t + t must never be lower than the shortest possible clock period, 1/f (max). CH CL C 2. Value guaranteed by characterization, not 100% tested in production. 3. t must be compatible with t (clock low time): if t is the Read setup time of the SPI bus master, t must be equal to CLQV CL SU CL (or greater than) t +t . CLQV SU DocID023103 Rev 8 33/43 42

DC and AC parameters M95128-A125 M95128-A145 Figure 17. AC measurement I/O waveform (cid:44)(cid:81)(cid:83)(cid:88)(cid:87)(cid:3)(cid:68)(cid:81)(cid:71)(cid:3)(cid:50)(cid:88)(cid:87)(cid:83)(cid:88)(cid:87) (cid:44)(cid:81)(cid:83)(cid:88)(cid:87)(cid:3)(cid:47)(cid:72)(cid:89)(cid:72)(cid:79)(cid:86) (cid:55)(cid:76)(cid:80)(cid:76)(cid:81)(cid:74)(cid:3)(cid:53)(cid:72)(cid:73)(cid:72)(cid:85)(cid:72)(cid:81)(cid:70)(cid:72)(cid:3)(cid:47)(cid:72)(cid:89)(cid:72)(cid:79)(cid:86) (cid:19)(cid:17)(cid:27)(cid:3)(cid:3276)(cid:3)(cid:57) (cid:38)(cid:38) (cid:19)(cid:17)(cid:26)(cid:3)(cid:3276)(cid:3)(cid:57) (cid:38)(cid:38) (cid:19)(cid:17)(cid:22)(cid:3)(cid:3276)(cid:3)(cid:57) (cid:38)(cid:38) (cid:19)(cid:17)(cid:21)(cid:3)(cid:3276)(cid:3)(cid:57) (cid:38)(cid:38) (cid:36)(cid:44)(cid:19)(cid:19)(cid:27)(cid:21)(cid:24)(cid:38) Figure 18. Serial input timing (cid:87)(cid:54)(cid:43)(cid:54)(cid:47) (cid:54) (cid:87)(cid:38)(cid:43)(cid:54)(cid:47) (cid:87)(cid:54)(cid:47)(cid:38)(cid:43) (cid:87)(cid:38)(cid:43) (cid:87)(cid:38)(cid:43)(cid:54)(cid:43) (cid:87)(cid:54)(cid:43)(cid:38)(cid:43) (cid:38) (cid:87)(cid:39)(cid:57)(cid:38)(cid:43) (cid:87)(cid:38)(cid:43)(cid:38)(cid:47) (cid:87)(cid:38)(cid:47) (cid:87)(cid:38)(cid:47)(cid:38)(cid:43) (cid:87)(cid:38)(cid:43)(cid:39)(cid:59) (cid:39) (cid:48)(cid:54)(cid:37)(cid:3)(cid:44)(cid:49) (cid:47)(cid:54)(cid:37)(cid:3)(cid:44)(cid:49) (cid:43)(cid:76)(cid:74)(cid:75)(cid:3)(cid:76)(cid:80)(cid:83)(cid:72)(cid:71)(cid:68)(cid:81)(cid:70)(cid:72) (cid:52) (cid:36)(cid:44)(cid:19)(cid:20)(cid:23)(cid:23)(cid:26)(cid:71) Figure 19. Hold timing (cid:54) (cid:87)(cid:43)(cid:47)(cid:38)(cid:43) (cid:87)(cid:38)(cid:47)(cid:43)(cid:47) (cid:87)(cid:43)(cid:43)(cid:38)(cid:43) (cid:38) (cid:87)(cid:38)(cid:47)(cid:43)(cid:43) (cid:87)(cid:43)(cid:47)(cid:52)(cid:61) (cid:87)(cid:43)(cid:43)(cid:52)(cid:57) (cid:52) (cid:43)(cid:50)(cid:47)(cid:39) (cid:36)(cid:44)(cid:19)(cid:20)(cid:23)(cid:23)(cid:27)(cid:70) 34/43 DocID023103 Rev 8

M95128-A125 M95128-A145 DC and AC parameters Figure 20. Serial output timing (cid:54) (cid:87)(cid:38)(cid:43) (cid:87)(cid:54)(cid:43)(cid:54)(cid:47) (cid:38) (cid:87)(cid:38)(cid:47)(cid:52)(cid:57) (cid:87)(cid:38)(cid:47)(cid:38)(cid:43) (cid:87)(cid:38)(cid:43)(cid:38)(cid:47) (cid:87)(cid:38)(cid:47) (cid:87)(cid:54)(cid:43)(cid:52)(cid:61) (cid:87)(cid:38)(cid:47)(cid:52)(cid:59) (cid:52) (cid:87)(cid:52)(cid:47)(cid:52)(cid:43) (cid:87)(cid:52)(cid:43)(cid:52)(cid:47) (cid:36)(cid:39)(cid:39)(cid:53) (cid:39) (cid:47)(cid:54)(cid:37)(cid:3)(cid:44)(cid:49) (cid:36)(cid:44)(cid:19)(cid:20)(cid:23)(cid:23)(cid:28)(cid:74) DocID023103 Rev 8 35/43 42

Package mechanical data M95128-A125 M95128-A145 9 Package mechanical data In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. 9.1 SO8N package information Figure 21. SO8N – 8-lead plastic small outline, 150 mils body width, package outline (cid:75)(cid:3)(cid:91)(cid:3)(cid:23)(cid:24)(cid:219) (cid:36)(cid:21) (cid:36) (cid:70) (cid:70)(cid:70)(cid:70) (cid:69) (cid:72) (cid:19)(cid:17)(cid:21)(cid:24)(cid:3)(cid:80)(cid:80) (cid:39) (cid:42)(cid:36)(cid:56)(cid:42)(cid:40)(cid:3)(cid:51)(cid:47)(cid:36)(cid:49)(cid:40) (cid:78) (cid:27) (cid:40)(cid:20) (cid:40) (cid:20) (cid:36)(cid:20) (cid:47) (cid:47)(cid:20) (cid:54)(cid:50)(cid:16)(cid:36)(cid:66)(cid:57)(cid:21) 1. Drawing is not to scale. Table 16. SO8N – 8-lead plastic small outline, 150 mils body width, package mechanical data millimeters inches(1) Symbol Min. Typ. Max. Min. Typ. Max. A - - 1.750 - - 0.0689 A1 0.100 - 0.250 0.0039 - 0.0098 A2 1.250 - - 0.0492 - - b 0.280 - 0.480 0.0110 - 0.0189 c 0.170 - 0.230 0.0067 - 0.0091 D 4.800 4.900 5.000 0.1890 0.1929 0.1969 E 5.800 6.000 6.200 0.2283 0.2362 0.2441 E1 3.800 3.900 4.000 0.1496 0.1535 0.1575 e - 1.270 - - 0.0500 - h 0.250 - 0.500 0.0098 - 0.0197 k 0° - 8° 0° - 8° L 0.400 - 1.270 0.0157 - 0.0500 36/43 DocID023103 Rev 8

M95128-A125 M95128-A145 Package mechanical data Table 16. SO8N – 8-lead plastic small outline, 150 mils body width, package mechanical data (continued) millimeters inches(1) Symbol Min. Typ. Max. Min. Typ. Max. L1 - 1.040 - - 0.0409 - ccc - - 0.100 - - 0.0039 1. Values in inches are converted from mm and rounded to four decimal digits. Figure 22. SO8N – 8-lead plastic small outline, 150 mils body width, package recommended footprint (cid:19)(cid:17)(cid:25)(cid:3)(cid:11)(cid:91)(cid:27)(cid:12) (cid:28)(cid:26) (cid:22)(cid:17)(cid:25)(cid:17) (cid:20)(cid:17)(cid:21)(cid:26) (cid:50)(cid:26)(cid:66)(cid:54)(cid:50)(cid:27)(cid:49)(cid:66)(cid:41)(cid:51)(cid:66)(cid:57)(cid:20) 1. Dimensions are expressed in millimeters. DocID023103 Rev 8 37/43 42

Package mechanical data M95128-A125 M95128-A145 9.2 TSSOP8 package information Figure 23. TSSOP8 – 8-lead thin shrink small outline, 3 x 4.4 mm, 0.65 mm pitch, package outline (cid:24) (cid:1012) (cid:1009) (cid:272) (cid:28)(cid:1005) (cid:28) (cid:1005) (cid:1008) (cid:626) (cid:4)(cid:1005) (cid:62) (cid:4) (cid:4)(cid:1006) (cid:18)(cid:87) (cid:62)(cid:1005) (cid:271) (cid:286) (cid:55)(cid:54)(cid:54)(cid:50)(cid:51)(cid:27)(cid:36)(cid:48)(cid:66)(cid:57)(cid:21) 1. Drawing is not to scale. Table 17. TSSOP8 – 8-lead thin shrink small outline, 3 x 4.4 mm, 0.65 mm pitch, package mechanical data millimeters inches(1) Symbol Min. Typ. Max. Min. Typ. Max. A - - 1.200 - - 0.0472 A1 0.050 - 0.150 0.0020 - 0.0059 A2 0.800 1.000 1.050 0.0315 0.0394 0.0413 b 0.190 - 0.300 0.0075 - 0.0118 c 0.090 - 0.200 0.0035 - 0.0079 CP - - 0.100 - - 0.0039 D 2.900 3.000 3.100 0.1142 0.1181 0.1220 e - 0.650 - - 0.0256 - E 6.200 6.400 6.600 0.2441 0.2520 0.2598 E1 4.300 4.400 4.500 0.1693 0.1732 0.1772 L 0.450 0.600 0.750 0.0177 0.0236 0.0295 L1 - 1.000 - - 0.0394 - α 0° - 8° 0° - 8° 1. Values in inches are converted from mm and rounded to four decimal digits. 38/43 DocID023103 Rev 8

M95128-A125 M95128-A145 Package mechanical data 9.3 WFDFPN8 package information Figure 24. WFDFPN8 (MLP8) – 8-lead, 2 x 3 mm, 0.5 mm pitch very very thin fine pitch dual flat package outline (cid:39)(cid:21) (cid:39)(cid:21)(cid:18)(cid:21) (cid:39)(cid:68)(cid:87)(cid:88)(cid:80)(cid:3)(cid:60) (cid:39) (cid:36) (cid:37) (cid:72) (cid:51)(cid:76)(cid:81)(cid:3)(cid:6)(cid:20)(cid:3)(cid:44)(cid:39)(cid:3)(cid:80)(cid:68)(cid:85)(cid:78)(cid:76)(cid:81)(cid:74) (cid:51)(cid:76)(cid:81)(cid:3)(cid:6)(cid:20) (cid:40) (cid:40)(cid:21)(cid:18)(cid:21) (cid:40)(cid:21) (cid:54)(cid:72)(cid:72)(cid:3)(cid:61) (cid:39)(cid:72)(cid:87)(cid:68)(cid:76)(cid:79) (cid:21)(cid:91) (cid:68)(cid:68)(cid:68)(cid:35) (cid:46) (cid:49)(cid:59)(cid:3)(cid:69) (cid:69)(cid:69)(cid:69)(cid:45) (cid:38) (cid:36)(cid:37) (cid:21)(cid:91) (cid:68)(cid:68)(cid:68)(cid:35) (cid:11)(cid:49)(cid:39)(cid:16)(cid:20)(cid:12)(cid:3)(cid:91)(cid:3)(cid:72) (cid:71)(cid:71)(cid:71)(cid:45) (cid:38) (cid:55)(cid:82)(cid:83)(cid:3)(cid:89)(cid:76)(cid:72)(cid:90) (cid:37)(cid:82)(cid:87)(cid:87)(cid:82)(cid:80)(cid:3)(cid:89)(cid:76)(cid:72)(cid:90) (cid:39)(cid:68)(cid:87)(cid:88)(cid:80)(cid:3)(cid:60) (cid:18)(cid:18) (cid:70)(cid:70)(cid:70)(cid:35) (cid:38) (cid:72)(cid:72)(cid:72)(cid:35) (cid:36) (cid:54)(cid:72)(cid:68)(cid:87)(cid:76)(cid:81)(cid:74)(cid:3)(cid:83)(cid:79)(cid:68)(cid:81)(cid:72) (cid:36)(cid:20) (cid:47) (cid:47)(cid:22) (cid:47)(cid:20) (cid:54)(cid:76)(cid:71)(cid:72)(cid:3)(cid:89)(cid:76)(cid:72)(cid:90) (cid:72)(cid:18)(cid:21) (cid:72) (cid:55)(cid:72)(cid:85)(cid:80)(cid:76)(cid:81)(cid:68)(cid:79)(cid:3)(cid:87)(cid:76)(cid:83) (cid:39)(cid:72)(cid:87)(cid:68)(cid:76)(cid:79)(cid:3)(cid:179)(cid:61)(cid:180) (cid:36)(cid:19)(cid:60)(cid:22)(cid:66)(cid:48)(cid:40)(cid:66)(cid:57)(cid:22) 1. Drawing is not to scale. 2. The central pad (the area E2 by D2 in the above illustration) must be either connected to Vss or left floating (not connected) in the end application. DocID023103 Rev 8 39/43 42

Package mechanical data M95128-A125 M95128-A145 Table 18. WFPN8 (MLP8) – 8-lead, 2 x 3 mm, 0.5 mm pitch very very thin fine pitch dual flat package mechanical data millimeters inches(1) Symbol Min. Typ. Max. Min. Typ. Max. A 0.700 0.750 0.800 0.0276 0.0295 0.0315 A1 0.025 0.045 0.065 0.0010 0.0018 0.0026 b 0.200 0.250 0.300 0.0079 0.0098 0.0118 D 1.900 2.000 2.100 0.0748 0.0787 0.0827 E 2.900 3.000 3.100 0.1142 0.1181 0.1220 e - 0.500 - - 0.0197 - L1 - - 0.150 - - 0.0059 L3 0.300 - - 0.0118 - - D2 1.050 - 1.650 0.0413 - 0.0650 E2 1.050 - 1.450 0.0413 - 0.0571 K 0.400 - - 0.0157 - - L 0.300 - 0.500 0.0118 - 0.0197 NX(2) 8 ND(3) 4 aaa 0.150 0.0059 bbb 0.100 0.0039 ccc 0.100 0.0039 ddd 0.050 0.0020 eee(4) 0.080 0.0031 1. Values in inches are converted from mm and rounded to four decimal digits. 2. NX is the number of terminals. 3. ND is the number of terminals on “D” sides. 4. Applied for exposed die paddle and terminals. Exclude embedding part of exposed die paddle from mea- suring. 40/43 DocID023103 Rev 8

M95128-A125 M95128-A145 Part numbering 10 Part numbering Table 19. Ordering information scheme Example: M95128-D W DW 4 T P /K Device type M95 = SPI serial access EEPROM Device function 128-D = 128 Kbit (16 Kbyte) plus Identification Page Operating voltage W = V = 2.5 to 5.5 V CC R = V = 1.7 to 5.5 V CC Package(1) MN = SO8 (150 mils width) DW = TSSOP8 (169 mils width) MF = WFDFPN8 (2 x 3 mm) Device grade 3 = –40 to 125 °C. Device tested with high reliability certified flow(2) 4 = –40 to 145 °C. Device tested with high reliability certified flow(2) Option blank = Tube packing T = Tape and reel packing Plating technology P or G = ECOPACK2® Process letter /K = Manufacturing technology code 1. All packages are ECOPACK2® (RoHS compliant and free of brominated, chlorinated and antimony-oxide flame retardants). 2. The high reliability certified flow (HRCF) is described in quality note QNEE9801. Please ask your nearest ST sales office for a copy. For a list of available options (speed, package, etc.) or for further information on any aspect of this device, please contact your nearest ST sales office. Engineering samples Parts marked as “ES”, “E” or accompanied by an Engineering Sample notification letter, are not yet qualified and therefore not yet ready to be used in production and any consequences deriving from such usage will not be at ST charge. In no event, ST will be liable for any customer usage of these engineering samples in production. ST Quality has to be contacted prior to any decision to use these Engineering samples to run qualification activity. DocID023103 Rev 8 41/43 42

Revision history M95128-A125 M95128-A145 11 Revision history Table 20. Document revision history Date Revision Changes 17-Apr-2012 1 Initial release. Deleted line “128 = 128 Kbit (16 Kbytes x 8)” in section “Device 04-Oct-2012 2 function” of Table 19: Ordering information scheme. Changed datasheet status from “Preliminary data” to “Production data”. Updated V maximum value in Table 13: DC characteristics RES (voltage range W, temperature range 4) and Table 14: DC 30-Jan-2013 3 characteristics (voltage range R, temperature range 3). Rephrased introduction of Section 3.5: Identification page and information about Identification page in Section 6: Delivery state. Deleted note(1) under Table 6: Instruction set. Updated note (1) under Table 8: Absolute maximum ratings. Replaced UFDFPN8 package (MC) by WFDFPN8 package (MF). 04-Dec-2013 4 Modified the Data retention from “40 years at 50 °C” to “50 years at 125 °C” Updated Note 2 below Table 8: Absolute maximum ratings Updated Table 14: DC characteristics (voltage range R, temperature range 3). Updated Table 18: WFPN8 (MLP8) – 8-lead, 2 x 3 mm, 0.5 mm pitch 24-Oct-2014 5 very very thin fine pitch dual flat package mechanical data Updated Table 19: Ordering information scheme. Added Note 2 below Figure 24: WFDFPN8 (MLP8) – 8-lead, 2 x 3 mm, 0.5 mm pitch very very thin fine pitch dual flat package outline. Updated Table 18: WFPN8 (MLP8) – 8-lead, 2 x 3 mm, 0.5 mm pitch very very thin fine pitch dual flat package mechanical data 15-Jan-2015 6 Updated Figure 24: WFDFPN8 (MLP8) – 8-lead, 2 x 3 mm, 0.5 mm pitch very very thin fine pitch dual flat package outline Added paragraph: Engineering samples on page 41 Updated 22-Jan-2016 7 – Section 9: Package mechanical data – V min value. CC Updated – Title of Figure 23: TSSOP8 – 8-lead thin shrink small outline, 3 x 29-Jan-2016 8 4.4 mm, 0.65 mm pitch, package outline Title of Table 17: TSSOP8 – 8-lead thin shrink small outline, 3 x 4.4 mm, 0.65 mm pitch, package mechanical data 42/43 DocID023103 Rev 8

M95128-A125 M95128-A145 IMPORTANT NOTICE – PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. © 2016 STMicroelectronics – All rights reserved DocID023103 Rev 8 43/43 43

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: S TMicroelectronics: M95128-DRDW3TP/K M95128-DRMN3TP/K M95128-DWDW4TP/K M95128-DRMF3TG/K