Series M Miniature Rockers s e gl g General Specifications o T s ker B Electrical Capacity (Resistive Load) c o R Power Level (silver): 6A @ 125V AC & 3A @ 250V AC 4A @ 30V DC for On-None-On; 3A @ 30V DC for all other circuits s on Logic Level (gold): 0.4VA maximum @ 28V AC/DC maximum utt (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) b h s Logic/Power Level (gold over silver): Combines silver & gold ratings u P Note: Find additional explanation of dual rating & operating range in Supplement section. B P ed Other Ratings at n mi Contact Resistance: 10 milliohms maximum for silver; 20 milliohms maximum for gold u Ill Insulation Resistance: 1,000 megohms minimum @ 500V DC e Dielectric Strength: 1,000V AC minimum between contacts for 1 minute minimum; bl ma 1,500V AC minimum between contacts and case for 1 minute minimum m a Mechanical Life: 50,000 operations minimum gr o Electrical Life: 25,000 operations minimum for silver; 50,000 operations minimum for gold; Pr 50,000 operations minimum for silver at 3A @ 125V AC s Angle of Throw: 25° k c o eyl Materials & Finishes K Actuator Clip & Mounting Frame: Stainless Steel Body Frame: Stainless steel s arie Case: Diallyl phthalate resin (UL94V–0) ot Movable Contactor: Phosphor bronze with silver or gold plating R Movable Contacts: Silver alloy (code W); copper with gold plating (code G); or silver alloy with gold plating (code A) Stationary Contacts: Silver with silver plating (code W); copper or brass with gold plating (code G); s or silver with gold plating (code A) e Slid Terminals: Copper or brass with silver plating; or copper or brass with gold plating Environmental Data Operating Temp Range: –30°C through +85°C (–22°F through +185°F) s e ctil Humidity: 90 ~ 95% humidity for 96 hours @ 40°C (104°F) Ta Vibration: 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours Shock: 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Tilt Processing Soldering: Wave Soldering (PC version) for Gold: See Profile A in Supplement section. Manual Soldering for Gold: See Profile A in Supplement section. Wave Soldering (PC version) for Silver: See Profile B in Supplement section. h c Manual Soldering for Silver: See Profile B in Supplement section. u o T Note: Actuator must be in OFF (center) position while soldering. Cleaning: These devices are not process sealed. Hand clean locally using alcohol based solution. s or Standards & Certifications at c di Flammability Standards: UL94V–0 for case n I UL: File No. E44145 - Recognized only when ordered with marking on switch. Add “/U” or “/CUL ” before first dash in part number to order UL recognized switch. s e ori All models recognized at 6A @ 125V AC, 3A @ 250V AC or 0.4VA maximum @ 28V DC maximum. ss CSA: File No. 023535_0_000 - Certified only when ordered with marking on switch. e cc Add “/C” before first dash in part number to order CSA certified switch. A All models certified at 6A @ 125V AC or 3A @ 250V AC or 0.4VA maximum @ 28V maximum. nt e m e pl p u S B62 www.nkkswitches.com 3/13/17

Series M Miniature Rockers s e gl Distinctive Characteristics g o T s B ker c o R Three methods of panel mounting: flat frame for flush with face or subpanel, snap-in, and PCB. s n o utt b High insulating barriers increase isolation of circuits in multipole devices sh u P and provide added protection to contact points. B P d e The molded diallyl phthalate case has a UL 94V-0 nat mi flammability rating. u Ill e bl a Epoxy sealed terminals prevent entry of solder flux m m and other contaminants. gra o Pr Prominent external insulating barriers increase s k insulation resistance and dielectric strength. oc yl e K Bias guard prevents misalignment of contacts; interlocking of actuator block with rocker and es internal guide does not allow transmission of ari ot R diagonal force on rocker to reach contact mechanism. s e d Clinching of the frame to the case well above the base Sli and terminals provides 1,500V dielectric strength. s e ctil a T Tilt Actual Size h Snap-in Mount Page B64 uc o T s or at c di n Bracket PC Mount Page B72 I s e ori s s e c c A Flat Frame Mount Page B83 nt e m e pl p u S www.nkkswitches.com B63

Series M Snap-In Mount Miniature Rockers s e gl TYPICAL SWITCH ORDERING EXAMPLE g o T s M20 1 2 TJ W 01 F C ker B c o R s n o butt Poles Rockers & Paddles h s Pu 1 SPDT F .450” (11.43mm) Wide Rocker ed PB 2 DSPP3DTT Mounting Frame Terminals G .450” (11.43mm) Wide Paddle nat TJ Snap-in Frame 01 Solder Lug S .453” (11.5mm) False mi Illluminated Rocker in Black only Illu 02 Quick Connect able 03 .250” (6.35mm) m Straight PC m a Circuits ogr 05 .425” (10.8mm) Rocker & Paddle Pr 2 ON NONE ON Wirewrap Colors ks 3 ON OFF ON 06 .750” (19.05mm) A Black c Wirewrap ylo 5 ON NONE (ON) B White Ke 8 (ON) OFF (ON) 07 .964” (24.5mm) C Red Wirewrap 9 ON OFF (ON) E Yellow 1.062” (27.0mm) aries *4 ON ON ON 08 Wirewrap F Green Rot *6 (ON) ON (ON) G Blue *7 ON ON (ON) H Gray s ( ) = Momentary e Contact Materials & Ratings d Sli *3-ON circuits Silver; Rated W 6A @ 125V AC & 3A @ 250V AC s Gold; Rated e G ctil 0.4VA max @ 28V AC/DC max a T Gold over Silver; Rated A 6A @ 125V AC & 0.4VA max @ 28V AC/DC max Tilt h c DESCRIPTION FOR TYPICAL ORDERING EXAMPLE u o T M2012TJW01-FC-1A s or at Red .450” (11.43mm) c di Wide Rocker n I Black Bezel without LED es SPDT ori ON-NONE-ON Circuit Snap-in Frame s s e c Ac Silver Contacts with 6–Amp Rating nt Solder Lug Terminals e m e pl p u S B64 www.nkkswitches.com

Series M Snap-In Mount Miniature Rockers s e TYPICAL SWITCH ORDERING EXAMPLE gl g o T 1 A s B ker c o R s n o Optional Bezels Bezel Colors LED Colors butt h s u P 1 Bezel without LED A Black B P d B White e at n E Yellow mi u F Green Ill e bl G Blue a m m H Gray a gr o Pr s k 2 Bezel with 1 Round LED A Black 1 LED c o yl C Red Ke F Green s e ari 3 Bezel with 2 Round LEDs A Black 2 LEDs ot R Bezel with 2 Rectangular Top LED Bottom LED 4 LEDs C Red C Red s e d E Yellow E Yellow Sli F Green F Green s e IMPORTANT: ctil a T Switches are supplied without UL, cULus & CSA marking unless specified. UL, cULus & CSA recognized only when ordered with marking on the switch. Specific models, ratings, & ordering instructions are noted on the General Specifications page. Tilt h DESCRIPTION FOR TYPICAL ORDERING EXAMPLE c u o T M2012TJW01-FC-3A-CF s or Red .450” (11.43mm) cat Wide Rocker Top LED Red ndi I Bottom LED Green Snap-in Frame s e SPDT ON-NONE-ON Circuit Black Bezel with ori 2 Round LEDs ss Silver Contacts with e c c 6–Amp Rating A Solder Lug Terminals nt e m e pl p u S www.nkkswitches.com B65

Series M Snap-In Mount Miniature Rockers s e gl POLES & CIRCUITS g o T Rocker Position ( ) = Momentary Connected Terminals Throw & Schematics s Down Center Up Down Center Up ker B Note: Terminal numbers are not c Pole Model Ro actually on the switch. ns M2012 ON NONE ON SPDT o utt M2013 ON OFF ON 2 (COM) b h SP M2015 ON NONE (ON) 2-3 OPEN 2-1 s Pu M2018 (ON) OFF (ON) 3 1 B M2019 ON OFF (ON) P d ate M2022 ON NONE ON DPDT n mi M2023 ON OFF ON u 2 (COM) 5 Ill DP M2025 ON NONE (ON) 2-3 5-6 OPEN 2-1 5-4 ble M2028 (ON) OFF (ON) 3 1 6 4 a m M2029 ON OFF (ON) m a ogr For 3 Throw (3-On) Pr Connected Terminals & Schematic s ck Pole Model Down Center Up External Connection o yl e M2024 ON ON ON The SP3T model utilizes a double pole K SP M2026 (ON) ON (ON) base. M2027 ON ON (ON) s (out) arie ConExnteecrntioanl ConExnteecrntioanl ConExnteecrntioanl Ecoxntenrencatli on External 6 3 Rot 2 (in) 5 2 (in) 5 2 (in) 5 must be made Conn 5 2 C(ino)mmon during field 4 1 installation. 1 (out) 34 (out) 6 (out) 1 (out) 34 (out) 6 (out) 1 (out) 3 4 (out)6 (out) (out) (out) s e 2-3 5-6 2-3 5-4 2-1 5-4 d Sli MOUNTING FRAME s ctile TJ Snap-in Frame Panel Cutout for Panel Cutout for a T Single Pole (15.9) Double Pole (15.9) .626 .626 without Bezel without Bezel Tilt ( 1.781.00) 25° (.1429.25) .(1531.61) (2.54) Dia .100 Panel Thickness without Bezel: .039” ~ .126” (1.0mm ~ 3.2mm) (12.2) (4.3) .480 .170 Panel Thickness with Bezel: .039” ~ .098” (1.0mm ~ 2.5mm) h c u o T CONTACT MATERIALS & RATINGS s W or Silver over Silver Power Level 6A @ 125V AC & 3A @ 250V AC at c di n I G Gold over Brass or Copper Logic Level 0.4VA maximum @ 28V AC/DC maximum s e ori Note: See Supplement section to find complete explanation of operating range. s s e c c A A Power Level 6A @ 125V AC Gold over Silver or Logic Level or 0.4VA maximum @ 28V AC/DC maximum nt e m e Note: This dual rated option is suitable when two or more identical switches are used in logic and in power circuits within the ppl same application. See Supplement section to find complete explanation of dual rating and operating range. u S B66 www.nkkswitches.com

Series M Snap-In Mount Miniature Rockers s e TERMINALS gl g o T .062” (1.57mm) Wide 01 02 Solder Lug Quick Connect Epoxy Seal (.415.07) Epoxy Seal (6.2.3550) B ckers o (2.0) (2.0) R .079 (1.1) .079 (1.57) .043 .062 T h k = .(003.81) T h k = .(003.81) ons utt b h (4.8) s 03 .250” (6.35mm) .189 Pu Straight PC 3 3 6 (4.7) Typ (4.7) Typ B Epoxy Seal (4.8) (.62.5305) 2.185 2 5 .185 d P .189 e 1 1 4 at n (1.17) (1.8) Dia Typ mi .046 .073 (1.8) Dia Typ u Thk = (0.8) .073 Ill .031 e Single Pole Double Pole bl a m m a 05 .425” (10.8mm) gr o Wirewrap or Extended PC Pr If using as extended PC terminal, refer to 06 .750” (19.05mm) Epoxy Seal the above footprints. cks Wirewrap or Extended PC A ylo e K .964” (24.5mm) Dimension A = terminal lengths as shown 07 Wirewrap or Extended PC (1.27) beside the terminal codes Thk = (0.8) .050 at the left. es 08 1.062” (27.0mm) .031 ari Wirewrap or Extended PC ot R ROCKERS & PADDLES s e d Sli AT4150 AT4151 F G .450” (11.43mm) .450” (11.43mm) Wide Rocker Wide Paddle (2.36) .093 s Material: Polyamide (.93.6192) (1.41.5403) Material: Polyamide (16.36) Tactile Finish: Matte Finish: Matte .644 (7.11) (5.84) R (6.3).280 .230 .248 Colors Available: Colors Available: A, B, C, E, F, G, H (1.8) A, B, C, E, F, G, H (1.41.5403) .(01.781) Tilt .071 (11.8) (11.8) .465 .465 h c u o AT466 .453” (11.5mm) T S False Illuminated Rocker Rocker False Illuminator .(383.69) (.1414.35) ors at c Material: Polycarbonate Acrylonitrile Butadiene Styrene (7.7) di .303 n Finish: Glossy I Colors: Black White and Red (.1415.53) (11.8) .(017.81) ories .465 ss e When a bezel is selected with AT466, glossy polycarbonate AT207 is supplied. c c A Cap Colors A B C E F G H ment Available: Black White Red Yellow Green Blue Gray e pl p u S www.nkkswitches.com B67

Series M Snap-In Mount Miniature Rockers s e gl OPTIONAL SNAP-IN BEZELS & BEZEL COLORS g o T 1 AT2107 Bezel kers B (11.8) A Black F Green ((..11665522..9966)) oc Material: Polyamide .465 R (2.2) B G Finish: Matte .087 White Blue A s n (12.0) utto (1.651.64) .472 Single Pole Double Pole b (21.5) E H sh .846 Yellow Gray (12.5)mm (13.1)mm Pu A .492” .516” B P d e at AT208 Bezel n 2 A mi for AT070 LED Black B (8.8) Dia Illu .346 mable MPoalytecrairabl:o nate (.1794.80) (13.5) (.1416.85) .(028.27) LoEnD n ceoxlto pras g&e .specifications m .531 (13.8) a .543 gr Single Pole Double Pole Pro Finish: Glossy (.1427.20) (12.5)mm (13.1)mm (.1652.96) A Keylocks Cfoor nmtaacttt ef aficntoisrhy. (.1651.46)(5.4) Dia ( 3 10.1.92) B (6...42294526)m””m (6...52515568)m””m A .213 aries 3 AfoTr2 A1T26 B1e7z LeElD A Black Rot (10.0) (.1427.20) (.1652.96) Material: .394 Polycarbonate (2.2) LED colors & .087 es (7.8) specifications A Slid Finish: .3(101.78) on next page. Semi-glossy (8.0) .465(.2814.65) Sq Single Pole Double Pole .315 (3.0) Dia Typ (18.4)mm (18.7)mm .118 A s .724” .736” e ctil a T 4 AT213 Bezel A for AT618 LED Black (10.0) (12.0) (15.9) .394 .472 .626 Tilt MPoalytecrairabl:o nate (.20.709) Typ .(028.27) LED colors & (7.8) specifications A .307 Finish: (11.8) on next page. .465 Single Pole Double Pole Touch Semi-glossy (.83.105) (.519.07) Typ (.2814.65) Sq A (18.4)mm (18.7)mm .724” .736” s Bezel Assembly or at dic 1. Pry out tab on bezel to 2. Insert switch frame under 3. Push tab back into place. 4. Snap assembled bezel n I a 45° angle. tab and snap on bezel. and switch into panel. s e ori Tab 45° s s e c c A Tab nt e m e pl p u S B68 www.nkkswitches.com

Series M Snap-In Mount Miniature Rockers s e LED COLORS & SPECIFICATIONS gl g o T Bezel Orientation on Switch AFoTr0 7Be0z LeEl DAT208 AFoTr6 1Be7z LeEl DAT212 AFoTr6 1Be8z LeEl DAT213 B ckers o with 1 LED (5.08) Dia with 2 Round LEDs (3.0) Dia with 2 Rectangular LEDs (5.0) R .200 .118 .197 (7.7) (5.0) (7.0) ns .303 .197 .276 o utt Top LED Top LED b de de de sh Circuit Mark This Si Bottom LED Circuit Mark This Si (+) (-) Bottom LED Circuit Mark This Si (-) Puuminated PB (+) Ill (-) e bl (+) a m m a Note: Lead lengths may differ from manufacturing lot to lot. The longer lead is the anode (+). gr o Pr AT070 AT617 AT618 s k c o C F C E F C E F yl (+) (-) e K Color Red Green Red Yellow Green Red Yellow Green Maximum Forward Current I 25mA 50mA 30mA 30mA 25mA 25mA 30mA 25mA es FM ari Typical Forward Current I 20mA 30mA 20mA 20mA 20mA 20mA 20mA 20mA ot F R Forward Voltage V 2.8V 2.1V 2.0V 2.1V 2.25V 2.25V 2.1V 2.2V F Maximum Reverse Voltage V 4V 5V 5V 5V 5V 5V 5V 5V RM es d Current Reduction Rate 0.33 0.40 0.40 0.40 0.33 0.33 0.40 0.33 Sli Above 25°C ∆I mA/°C mA/°C mA/°C mA/°C mA/°C mA/°C mA/°C mA/°C F Ambient Temperature Range –10° ~ +70°C –15° ~ +70°C –25° ~ +70°C (when used with a bezel) es ctil a T The electrical specifications shown are determined at a basic temperature of 25°C. LED circuit is independent of switch operation. LED is colored in OFF state. If the source voltaTghee ibs aglrlaesatt erer stihsatonr tchael crualtaetdio vno altangde m oofr teh ela LmEpD ,d ae tabial lalarset srhesoiwstno ri nm tuhset bSeu pcpolnenmeecntet ds eicnt isoenr.i es with the lamp. Tilt LEGENDS h c u o T NKK Switches can provide custom legends for caps. Contact factory for more information. s or Suggested Printable Area for Cap at c di n (0.38) Typ I .015 (4.5) Typ es OFFON .177 ssori Recommended Print Method: (0.76) Typ (9.91) (0.76) Typ (3.36) Typ e .030 .390 .030 .132 cc (11.43) A Pad Print .450 nt e m Epoxy based ink is recommended. AT4150 Shaded areas are printable areas. e pl p u S www.nkkswitches.com B69

Series M Snap-In Mount Miniature Rockers s e gl TYPICAL SWITCH DIMENSIONS g o T Snap-in Frame • Solder Lug Single Pole s ker B (.419.94) . 0(14.13) xx (.20.709) Typ oc (2.8) Circuit Mark R .110 This Side ns (4.7) Typ 3 utto (.1780.09) 25° .185 2 (.1531.20) hb (0.8) Typ 1 s .031 u P PB (11.43) (0.5) (0.5) (2.0) Typ d .450 .020 .020 .079 nate (.1428.20) (.313.30) .(277.19) (.93.741) (.417.57) (.73.191) mi u M2012TJW01-FC Ill e bl Snap-in Frame • Solder Lug Double Pole a m m a gr (4.9) (1.1) x (2.0) Typ (4.8) Pro .194 (2.8) Circuit Mark .043 x .079 .189 .110 This Side s k c o 6 3 yl (4.7) Typ Ke (.1780.09) 25° .185 5 2 (.1531.20) (0.8) Typ .031 4 1 s e otari (1.41.5403) .(002.50) .(002.50) (.20.709) Typ R (12.2) (3.3) (7.1) (9.4) (4.5) (12.7) .480 .130 .279 .371 .177 .500 M2022TJW01-FC s e d Sli Snap-in Frame • Solder Lug Single Pole (2.8) Circuit Mark (1.1) x (2.0) Typ .110 This Side .043 x .079 s e ctil 3 Ta (4.7) Typ (.1780.09) 25° .185 2 (.1531.20) (0.8) Typ 1 .031 Tilt (11.43) (2.0.3963) (3.18) (0.5) (0.5) (2.0) Typ .450 .125 .020 .020 .079 (12.2) (13.7) (7.1) (9.4) (4.5) (7.9) .480 .539 .279 .371 .177 .311 h M2012TJW01-GC c u o T Snap-in Frame • Solder Lug Double Pole s cator (.211.80) CThiricsu Sitid Meark .(014.13) xx (.20.709) Typ (.418.89) di n I 6 3 (4.7) Typ ssories (.1780.09) 25° (.00..31881) 5Typ 45 12 (.1531.20) e c (2.36) Ac .093 (11.43) (3.18) (0.5) (0.5) (2.0) Typ .450 .125 .020 .020 .079 nt (12.2) (13.7) (7.1) (9.4) (4.5) (12.7) me .480 .539 .279 .371 .177 .500 e pl p M2022TJW01-GC u S B70 www.nkkswitches.com

Series M Snap-In Mount Miniature Rockers s e TYPICAL SWITCH DIMENSIONS gl g o T Single & Double Pole Snap-in Frame • AT2107 Bezel • Solder Lug (5.6) (1.1) x (2.0) Typ (4.8) s .221 Circuit Mark .043 x .079 .189 B ker This Side oc R 3 6 3 (12.0) (4.7) Typ (13.0) (13.0) (21.5).472 25° .185 2 .512(14.0) 5 2 .512(14.0) ns .846 (.00.381) Typ 1 .551 4 1 .551 butto h s u P (11.43) (4.3) .450 .169 B (.1416.85) .(028.27) .(002.50) (.20.709) (.20.709) Typ ed P (15.6) (4.01) (6.4) (9.4) (4.5) (7.9) (12.7) at .614 .158 .252 .371 .177 .311 .500 M2012TJW01-FC-1A min u Ill Double Pole Snap-in Frame • AT208 Bezel • Solder Lug ble a m (4.9) (15.3) Min (2.5) m .193 .602 (0.61) Sq .098 gra .024 Pro (5.08) Dia .200 (19.0) .748 CThiricsu Sitid Meark .(014.13) xx .(027.09) Typ ks (13.109.20) (1.533.51) (4.7) Typ 6 3 (13.0) eyloc (.1427.02) 25° .185 5 2 .512(14.0) K (0.8) Typ 4 1 .551 .031 s e (4.3) ari (1.41.540(31)1.8) (2.1.629) (0.5) (4.8) .(027.09) Typ Rot .465 .087 .020 .189 (15.6) (4.01) (6.4) (9.4) (4.5) (12.7) .614 .158 .252 .371 .177 .500 M2022TJW01-FC-2A-C s e d Single Pole Snap-in Frame • AT212 Bezel • Solder Lug Sli (10.0) (7.8) (5.6) (1.1) x (2.0) Typ .394 .307 .221 .043 x .079 Circuit Mark This Side s e 3 ctil (4.7) Typ (13.0) a (.83.105) (.1427.02) 25° .185 2 .512(14.0) T (0.8) Typ 1 .551 .031 (3.0) Dia Typ .118 (11.43) (4.3) Tilt .450 .169 (11.8) (2.2) (0.5) (2.0) .465 .087 .020 .079 (21.5) Sq (4.01) (6.4) (9.4) (4.5) (7.9) .846 .158 .252 .371 .177 .311 M2012TJW01-FC-3A-CF h c u o Double Pole Snap-in Frame • AT213 Bezel • Solder Lug T (10.0) (7.8) (5.6) (1.1) x (2.0) Typ .394 .307 .221 Circuit Mark .043 x .079 ors This Side at c 6 3 ndi (4.7) Typ (13.0) I (.83.105) (.1427.02) 25° .185 5 2 .512(14.0) (.00.381) Typ 4 1 .551 ories (5.0) Typ ss .197 e c (2.0) (11.43) (4.3) (0.5) (2.0) Typ Ac .079 .450 .169 .020 .079 (11.8) (2.2) (4.8) .465 .087 .189 nt (21.5) Sq (4.01) (6.4) (9.4) (4.5) (12.7) e .846 .158 .252 .371 .177 .500 em pl M2022TJW01-FC-4A-CF p u S www.nkkswitches.com B71

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: N KK Switches: M2012TJW02-FG-3A-FC M2029TJG02-FC-3A-CE M2024TJG01-GA-1A M2022TJW01-FC-2A-F M2013TJG01-FA- 4A-FF M2019TJA01-GH-2A-F M2019TJA01-FH-2A-F M2012TJA01-GH-3A-FC M2012TJG02-GA M2012TJG01-GA M2024TJG01 M2012TJW01-GA-2A-C M2013TJW03