Through Hole Lamp Product Data Sheet LTL-4231N Spec No.: DS-20-92-0246 Effective Date: 01/26/2013 Revision: E LITE-ON DCC RELEASE BNS-OD-FC001/A4 LITE-ON Technology Corp. / Optoelectronics No.90,Chien 1 Road, Chung Ho, New Taipei City 23585, Taiwan, R.O.C. Tel: 886-2-2222-6181 Fax: 886-2-2221-1948 / 886-2-2221-0660 http://www.liteon.com/opto BBNNSS--OODD--FFCC000011//AA44 BNS-OD-FC001/A4

LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Features * Lead (Pb) free product – RoHS compliant. * High Intensity. * Popular T-1 diameter package. * Selected minimum intensities. * Wide viewing angle. * General purpose leads. * Reliable and rugged. Package Dimensions Part No. Lens Source Color LTL-4231N Green Diffused Green Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25mm (.010") unless otherwise noted. 3. Protruded resin under flange is 1.0mm (.04") max. 4. Lead spacing is measured where the leads emerge from the package. 5. Specifications are subject to change without notice. Part No. : LTL-4231N Page : 1 of 10 BNS-OD-C131/A4

LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Absolute Maximum Ratings at TA=25°C Parameter Maximum Rating Unit Power Dissipation 120 mW Peak Forward Current 90 mA (1/10 Duty Cycle, 0.1ms Pulse Width) DC Forward Current 30 mA Operating Temperature Range -55℃ to + 100℃ Storage Temperature Range -55℃ to + 100℃ Lead Soldering Temperature 260℃ for 5 Seconds Max [2.0mm(.078") From Body] Part No. : LTL-4231N Page : 2 of 10 BNS-OD-C131/A4

LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Electrical / Optical Characteristics at TA=25°C Parameter Symbol Min. Typ. Max. Unit Test Condition IF = 10mA Luminous Intensity IV 5.6 12.6 85 mcd Note 1,5 Viewing Angle 2θ1/2 60 deg Note 2 (Fig.6) Dominant Wavelength λd 564 569 574 nm Note 3 Spectral Line Half-Width Δλ 30 nm Forward Voltage VF 2.1 2.6 V IF = 20mA VR = 5V Reverse Current IR 100 μA Note 6 NOTE: 1. Luminous intensity is measured with a light sens or and filter combination that approximates the CIE eye-response curve. 2. θ1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity. 3. The dominant wavelength, λd is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device. 4. Iv classification code is marked on each packing bag. 5. The Iv guarantee should be added ±15﹪tolerance. 6. Reverse voltage (VR) condition is applied for IR test only. The device is not designed for reverse operation Part No. : LTL-4231N Page : 3 of 10 BNS-OD-C131/A4

LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Typical Electrical / Optical Characteristics Curves (25°C Ambient Temperature Unless Otherwise Noted) Part No. : LTL-4231N Page : 4 of 10 BNS-OD-C131/A4

LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Packing Spec 1000, 500, 200 or 100 pcs per packing bag 10 packing bags per inner carton total 10000 pcs per inner carton 8 Inner cartons per outer carton total 80000 pcs per outer carton In every shipping lot, only the last pack will be non-full packing Part No. : LTL-4231N Page : 5 of 10 BNS-OD-C131/A4

LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Bin Code List For Reference Luminous Intensity Unit : mcd @10mA Bin Code Min. Max. N1 50 85 M1 29 50 L1 19 29 L2 12.6 19 L3 8.7 12.6 L4 5.6 8.7 Note: Tolerance of each bin limit is ±15% Dominant Wavelength Unit : nm @10mA Bin Code Min. Max. YG 571.0 574.0 PG 569.5 571.0 GG 568.0 569.5 GG1 566.0 568.0 GG2 564.0 566.0 Note: Tolerance of each bin limit is ±1nm Part No. : LTL-4231N Page : 6 of 10 BNS-OD-C131/A4

LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only CAUTIONS 1. Application The LEDs described here are intended to be used for ordinary electronic equipment (such as office equipment, communication equipment and household applications).Consult Liteon’s Sales in advance for information on applications in which exceptional reliability is required, particularly when the failure or malfunction of the LEDs may directly jeopardize life or health (such as in aviation, transportation, traffic control equipment, medical and life support systems and safety devices). 2. Storage The storage ambient for the LEDs should not exceed 30°C temperature or 70% relative humidity. It is recommended that LEDs out of their original packaging are used within three months. For extended storage out of their original packaging, it is recommended that the LEDs be stored in a sealed container with appropriate desiccant or in desiccators with nitrogen ambient. 3. Cleaning Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LEDs if necessary. 4. Lead Forming & Assembly During lead forming, the leads should be bent at a point at least 3mm from the base of LED lens. Do not use the base of the lead frame as a fulcrum during forming. Lead forming must be done before soldering, at normal temperature. During assembly on PCB, use minimum clinch force possible to avoid excessive mechanical stress. 5. Soldering When soldering, leave a minimum of 2mm clearance from the base of the lens to the soldering point. Dipping the lens into the solder must be avoided. Do not apply any external stress to the lead frame during soldering while the LED is at high temperature. Recommended soldering conditions : Soldering iron Wave soldering Temperature 350°C Max. Pre-heat 100°C Max. Soldering time 3 sec. Max. Pre-heat time 60 sec. Max. (one time only) Solder wave 260°C Max. Soldering time 5 sec. Max. Note: Excessive soldering temperature and/or time might result in deformation of the LED lens or catastrophic failure of the LED. IR reflow is not suitable process for through holes type LED lamp product. Part No. : LTL-4231N Page : 7 of 10 BNS-OD-C131/A4

LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only 6. Drive Method An LED is a current-operated device. In order to ensure intensity uniformity on multiple LEDs connected in parallel in an application, it is recommended that a current limiting resistor be incorporated in the drive circuit, in series with each LED as shown in Circuit A below. Circuit model A Circuit model B LED LED (A) Recommended circuit (B) The brightness of each LED might appear different due to the differences in the I-V characteristics of those LEDs 7. ESD (Electrostatic Discharge) Static Electricity or power surge will damage the LED. Suggestions to prevent ESD damage:  Use a conductive wrist band or anti- electrostatic glove when handling these LEDs  All devices, equipment, and machinery must be properly grounded  Work tables, storage racks, etc. should be properly grounded  Use ion blower to neutralize the static charge which might have built up on surface of the LEDs plastic lens as a result of friction between LEDs during storage and handing Part No. : LTL-4231N Page : 8 of 10 BNS-OD-C131/A4

LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only Suggested checking list : Training and Certification 1. Everyone working in a static-safe area is ESD-certified? 2. Training records kept and re-certification dates monitored? Static-Safe Workstation & Work Areas 1. Static-safe workstation or work-areas have ESD signs? 2. All surfaces and objects at all static-safe workstation and within 1 ft measure less than 100V? 3. All ionizer activated, positioned towards the units? 4. Each work surface mats grounding is good? Personnel Grounding 1. Every person (including visitors) handling ESD sensitive (ESDS) items wear wrist strap, heel strap or conductive shoes with conductive flooring? 2. If conductive footwear used, conductive flooring also present where operator stand or walk? 3. Garments, hairs or anything closer than 1 ft to ESD items measure less than 100V*? 4. Every wrist strap or heel strap/conductive shoes checked daily and result recorded for all DSL? 5. All wrist strap or heel strap checkers calibration up to date? Note: *50V for Blue LED. Device Handling 1. Every ESDS items identified by EIA-471 labels on item or packaging? 2. All ESDS items completely inside properly closed static-shielding containers when not at static-safe workstation? 3. No static charge generators (e.g. plastics) inside shielding containers with ESDS items? 4. All flexible conductive and dissipative package materials inspected before reuse or recycle? Others 1. Audit result reported to entity ESD control coordinator? 2. Corrective action from previous audits completed? 3. Are audit records complete and on file? Part No. : LTL-4231N Page : 9 of 10 BNS-OD-C131/A4

LITE-ON TECHNOLOGY CORPORATION Property of Lite-On Only 8. Reliability Test Classification Test Item Test Condition Reference Standard Ta= Under Room Temperature As MIL-STD-750D:1026 (1995) Operation Life Per Data Sheet Maximum Rating MIL-STD-883D:1005 (1991) *Test Time= 1000HRS (-24HRS,+72HRS) JIS C 7021:B-1 (1982) High Temperature Ta= 65±5°C MIL-STD-202F: 103B(1980) High Humidity RH= 90 ～ 95% JIS C 7021 : B-11(1982) Storage Test Time= 240HRS±2HRS Ta= 65±5°C High Temperature Endurance RH= 90 ～ 95% High Humidity JIS C 7021 : B-11(1982) Test VR=5V Reverse BIAS Test Time = 500HRS (-24HRS, +48HRS) High Temperature Ta= 105±5°C MIL-STD-883D:1008 (1991) Storage *Test Time= 1000HRS (-24HRS,+72HRS) JIS C 7021:B-10 (1982) Low Temperature Ta= -55±5°C JIS C 7021:B-12 (1982) Storage *Test Time=1000HRS (-24HRS,+72HRS) MIL-STD-202F:107D (1980) 105°C ～ 25°C ～ -55°C～ 25°C Temperature MIL-STD-750D:1051(1995) 30mins 5mins 30mins 5mins Cycling MIL-STD-883D:1010 (1991) 10 Cycles JIS C 7021: A-4(1982) 105 ± 5°C ～ -55°C ± 5°C MIL-STD-202F:107D(1980) Thermal 10mins 10mins MIL-STD-750D:1051(1995) Shock Environmental 10 Cycles MIL-STD-883D:1011 (1991) Test MIL-STD-202F:210A(1980) Solder T.sol = 260 ± 5°C MIL-STD-750D:2031(1995) Resistance Dwell Time= 10 ± 1secs JIS C 7021: A-1(1982) MIL-STD-202F:208D(1980) T. sol = 230 ± 5°C MIL-STD-750D:2026(1995) Solderability Dwell Time= 5 ± 1secs MIL-STD-883D:2003(1991) JIS C 7021: A-2(1982) 9. Others The appearance and specifications of the product may be modified for improvement, without prior notice. Part No. : LTL-4231N Page : 10 of 10 BNS-OD-C131/A4

Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: L ite-On: LTL-4231N LTL-4231N-1