Reference Only Spec No. JELF243B-0022L-01 P1/9 CHIP COIL (CHIP INDUCTORS) LQM2MPN□□□□G0L REFERENCE SPECIFICATION 1. Scope This reference specification applies to LQM2MPN_G0L series, Chip Coil (Chip Inductors). 2. Part Numbering (ex) LQ M 2M P N R47 M G 0 L Product ID Structure Dimension Applications Category Inductance Tolerance Dimension Other Packaging (L×W) and (T) L:Taping Characteristics *B:BULK *B:Bulk packing also available 3. Rating ・Operating Temperature Range – 55°C to + 125°C ・Storage Temperature Range – 55°C to + 125°C Inductance DC Self Rated Current*1 Customer MURATA Resistance Resonant (A) Part Number Part Number (Ω) Frequency (μH) Tolerance Typ Max (MHz min.) 85℃*2 125℃*2 LQM2MPNR47MG0L M：±20% 0.47 0.060 0.075 100 1.6 1.2 LQM2MPNR47NG0L N：±30% LQM2MPN1R0NG0L 1.0 N：±30% 0.085 0.107 60 1.4 1.0 LQM2MPN1R5MG0L M：±20% 1.5 0.11 0.138 50 1.2 0.9 LQM2MPN1R5NG0L N：±30% LQM2MPN2R2MG0L M：±20% 2.2 0.11 0.138 40 1.2 0.9 LQM2MPN2R2NG0L N：±30% LQM2MPN3R3NG0L 3.3 N：±30% 0.12 0.15 30 1.2 0.9 LQM2MPN4R7MG0L M：±20% 4.7 0.14 0.175 20 1.1 0.8 LQM2MPN4R7NG0L N：±30% *1 When applied Rated current to the Products, temperature rise caused by self-generated heat shall be limited to 40 ℃ max ) *2 Rated Current is derated as right figure (A Ratedcurrent depending on the operating temperature. nt at85°C e rr Cu Ratedcurrent d at125°C e at R 0 85 125 OperatingTemperature(°C) 4. Testing Conditions 《Unless otherwise specified》 《In case of doubt》 Temperature : Ordinary Temperature / 15°C to 35°C Temperature : 20°C ± 2°C Humidity : Ordinary Humidity / 25%(RH) to 85%(RH) Humidity : 60%(RH) to 70%(RH) Atmospheric Pressure : 86kPa to 106kPa MURATA MFG.CO., LTD

Reference Only Spec No. JELF243B-0022L-01 P2/9 5. Appearance and Dimensions 0.5±0.2 ■Unit Mass (Typical value) 0.012g 0.9±0.1 2.0±0.15 1.6±0.15 (in mm) 6. Electrical Performance No. Item Specification Test Method 6.1 Inductance Inductance shall meet item 3. Measuring Equipment: KEYSIGHT 4294A or quivalent (1mA) Measuring Frequency: 1MHz 6.2 DC Resistance DC Resistance shall meet item 3. Measuring Equipment: Digital multi meter Digitalmultimeter (TR6846orequivalent) a terminal1 SW terminal2 b DC resistance shall be measured after putting chip coil between the terminal 2 under the condition of opening between a and b. Every measurement the terminal 1 shall be shorted between a and b when changing chip coil. 6.3 Self Resonant S.R.F shall meet item 3. Measuring Equipment: Frequency (S.R.F) KEYSIGHT 4294A or equivalent 6.4 Rated Current Self temperature rise shall be The rated current is applied. limited to 40°C max. MURATA MFG.CO., LTD

Reference Only Spec No. JELF243B-0022L-01 P3/9 7. Mechanical Performance No. Item Specification Test Method 7.1 Shear Test Chip coil shall not be damaged after Applied Direction tested as follows. ChipCoil F Substrate Force: 10N Hold Duration: 5s±1s Applied Direction: Parallel to PCB 7.2 Bending Test Substrate: Glass-epoxy substrate (100mm×40mm×1.0mm) Solder: Reflow Pressure jig F R230 Deflection Produ c t (in mm) 45 45 Speed of Applying Force: 0.5mm / s Deflection: 3mm Hold Duration: 30 s 7.3 Vibration Oscillation Frequency: 10Hz to 2000Hz to 10Hz for 20 min Total amplitude 3.0 mm or Acceleration amplitude 245m/s2 whichever is smaller. Testing Time: A period of 4h in each of 3 mutually perpendicular directions. 7.4 Drop It shall be dropped on concrete or steel board. Method : free fall Height : 1m Total of 10 cycles 7.5 Solderability The wetting area of the electrode Flux: Ethanol solution of rosin 25(wt)% shall be at least 90% covered with (Immersed for 5s to 10s) new solder coating. Solder: Sn-3.0Ag-0.5Cu Pre-Heating: 150°C±10°C / 60s to 90s Solder Temperature: 240°C±5°C Immersion Time: 3s±1s 7.6 Resistance to Appearance: No damage Flux: Ethanol solution of rosin 25(wt)% Soldering Heat Inductance Change: within ±30% (Immersed for 5s to 10s) Solder: Sn-3.0Ag-0.5Cu Pre-Heating: 150°C±10°C / 60s to 90s Solder Temperature: 270°C±5°C Immersion Time: 10s±1s Then measured after exposure in the room condition for 24h±2h. MURATA MFG.CO., LTD

Reference Only Spec No. JELF243B-0022L-01 P4/9 8. Environmental Performance It shall be soldered on the substrate. No. Item Specification Test Method 8.1 Heat Resistance Appearance: No damage Temperature: 125°C±2°C Inductance Change: within ±30% Time: 1000h (+48h,-0h) Then measured after exposure in the room condition for 24h±2h. 8.2 Cold Resistance Temperature: -55°C±2°C Time: 1000h (+48h,-0h) Then measured after exposure in the room condition for 24h±2h. 8.3 Humidity Temperature: 70°C±2°C Humidity: 90%(RH) to 95%(RH) Time: 1000h (+48h,-0h) Then measured after exposure in the room condition for 24h±2h. 8.4 Temperature 1 cycle: Cycle 1 step: -55°C±2°C / 30 min±3 min 2 step: Ordinary temp. / 10 min to 15 min 3 step: 125°C±2°C / 30 min to 3 min 4 step: Ordinary temp. / 10 min to15 min Total of 100cycles Then measured after exposure in the room condition for 24h±2h. 9. Specification of Packaging 9.1 Appearance and Dimensions of plastic tape (8mm-wide) 2.0±0.05 φ1.5±00. 1 4.0±0.1 4.0±0.1 1.1±0.1 1.75±0.1 0.25±0.05 5 0 .1 ±0. 0.2 ±0 5 ± 3. 0 5 . 2 8 2. (in mm) Direction of feed 1.85±0.1 Dimension of the Cavity is measured at the bottom side. 9.2 Specification of Taping (1) Packing quantity (standard quantity) 3,000 pcs / reel (2) Packing Method Products shall be packed in the each embossed cavity of plastic tape and sealed by cover tape. (3) Sprocket hole The sprocket holes are to the right as the tape is pulled toward the user. (4) Spliced point Plastic tape and Cover tape has no spliced point. (5) Missing components number Missing components number within 0.1% of the number per reel or 1 pc., whichever is greater, and are not continuous. The Specified quantity per reel is kept. MURATA MFG.CO., LTD

Reference Only Spec No. JELF243B-0022L-01 P5/9 9.3 Pull Strength Plastic tape 10N min. Cover tape 5N min. 9.4 Peeling off force of cover tape 165 to 180 degree Speed of Peeling off 300mm / min F Cover tape Plastic tape: 0.1N to 0.7N Peeling off force (minimum value is typical) Plastic tape 9.5 Dimensions of Leader-tape, Trailer and Reel There shall be leader-tape (cover tape) and trailer-tape (empty tape) as follows. Trailer Leader 2.0±0.5 160min. Label 190min. 210min. Emptytape Covertape 13.0±0.2 60±10 21.0±0.8 Directionoffeed 9±10 13±1.4 180±03 (in mm) 9.6 Marking for reel Customer part number, MURATA part number, Inspection number (1), RoHS marking (2), Quantity etc ･･･ 1) <Expression of Inspection No.> □□ OOOO  (1) (2) (3) (1) Factory Code (2) Date First digit : Year / Last digit of year Second digit : Month / Jan. to Sep.  1 to 9, Oct. to Dec.  O, N, D Third, Fourth digit : Day (3) Serial No. 2) <Expression of RoHS marking > ROHS – Y (△) (1) (2) (1) RoHS regulation conformity parts. (2) MURATA classification number 9.7 Marking for Outside package (corrugated paper box) Customer name, Purchasing order number, Customer part number, MURATA part number, RoHS marking (2), Quantity, etc ･･･ 9.8 Specification of Outer Case Outer Case Dimensions Standard Reel Quantity (mm) Label in Outer Case (Reel) W D H H 186 186 93 5  D  Above Outer Case size is typical. It depends on a quantity of an order W MURATA MFG.CO., LTD

Reference Only Spec No. JELF243B-0022L-01 P6/9 10. ！ Caution Limitation of Applications Please contact us before using our products for the applications listed below which require especially high reliability for the prevention of defects which might directly cause damage to the third party's life, body or property. (1) Aircraft equipment (6) Transportation equipment (vehicles, trains, ships, etc.) (2) Aerospace equipment (7) Traffic signal equipment (3) Undersea equipment (8) Disaster prevention / crime prevention equipment (4) Power plant control equipment (9) Data-processing equipment (5) Medical equipment (10) Applications of similar complexity and /or reliability requirements to the applications listed in the above 11. Notice This product is designed for solder mounting. Please consult us in advance for applying other mounting method such as conductive adhesive. 11.1 Land pattern designing ChipCoil Land SolderResist c a 0.8 b 2.4 c 1.8 a b (in mm) 11.2 Flux, Solder ・Use rosin-based flux. Don’t use highly acidic flux with halide content exceeding 0.2(wt) % (chlorine conversion value). Don’t use water-soluble flux. ・Use Sn-3.0Ag-0.5Cu solder. ・Standard thickness of solder paste: 100μm to 150μm. 11.3 Flow soldering / Reflow soldering conditions ・Pre-heating should be in such a way that the temperature difference between solder and product surface is limited to 150°C max. Cooling into solvent after soldering also should be in such a way that the temperature difference is limited to 100°C max. Insufficient pre-heating may cause cracks on the product, resulting in the deterioration of products quality. ・Standard soldering profile and the limit soldering profile is as follows. The excessive limit soldering conditions may cause leaching of the electrode and/or resulting in the deterioration of product quality. Soldering profile (1) Flow soldering profile Temp. (℃) 265℃±3℃ 250℃ Limit Profile 150 Heating Time Standard Profile 60s min. Time.(s) Standard Profile Limit Profile Pre-heating 150℃, 60s min. Heating 250℃, 4s～6s 265℃±3℃, 5s Cycle of flow 2 times 2 times MURATA MFG.CO., LTD

Reference Only Spec No. JELF243B-0022L-01 P7/9 (2) Reflow soldering profile T(e℃mp). 260℃ 245℃±3℃ 230℃ 220℃ Limit Profile 180 150 30s～60s Standard Profile 60s max. 90s±30s Time.(s) Standard Profile Limit Profile Pre-heating 150°C～180°C, 90s±30s Heating above 220°C, 30s～60s above 230°C, 60s max. Peak temperature 245°C±3°C 260°C, 10s Cycle of reflow 2 times 2 times 11.4 Reworking with soldering iron The following conditions must be strictly followed when using a soldering iron. Pre-heating 150°C, 1 min Tip temperature 350°C max. Soldering iron output 80W max. Tip diameter φ3mm max. Soldering time 3(+1, -0)s Time 2 times Note : Do not directly touch the products with the tip of the soldering iron in order to prevent the crack on the products due to the thermal shock. 11.5 Solder Volume ・Solder shall be used not to be exceeded the upper limits as shown below. ・Accordingly increasing the solder volume, the mechanical stress to Chip is also increased. Exceeding solder volume may cause the failure of mechanical or electrical performance. Upper Limit Recommendable 1/3T≦t≦T t T： thickness of electrode 11.6 Product’s location The following shall be considered when designing and laying out P.C.B.'s. (1) P.C.B. shall be designed so that products are not subject to the mechanical stress due to warping the board. ［Products direction］ a Products shall be located in the sideways b direction (Length: a‹b) to the mechanical stress. 〈Poorexample〉 〈Goodexample〉 MURATA MFG.CO., LTD

Reference Only Spec No. JELF243B-0022L-01 P8/9 (2)Components location on P.C.B. separation. It is effective to implement the following measures, to reduce stress in separating the board. It is best to implement all of the following three measures; however, implement as many measures as possible to reduce stress. Contents of Measures Stress Level (1) Turn the mounting direction of the component parallel to the board separation surface. A > D *1 (2) Add slits in the board separation part. A > B (3) Keep the mounting position of the component away from the board separation surface. A > C C Perforation B D A Slit *1 A > D is valid when stress is added vertically to the perforation as with Hand Separation. If a Cutting Disc is used, stress will be diagonal to the PCB, therefore A > D is invalid. (3) Mounting Components Near Screw Holes When a component is mounted near a screw hole, it may be affected by the board deflection that occurs during the tightening of the screw. Mount the component in a position as far away from the screw holes as possible. Recommended Screw Hole 11.7 Cleaning Conditions Products shall be cleaned on the following conditions. (1) Cleaning temperature shall be limited to 60°C max. (40°C max for IPA.) (2) Ultrasonic cleaning shall comply with the following conditions with avoiding the resonance phenomenon at the mounted products and P.C.B. Power : 20 W / l max. Frequency : 28kHz to 40kHz Time : 5 min max. (3) Cleaner 1. Alcohol type cleaner Isopropyl alcohol (IPA) 2. Aqueous agent PINE ALPHA ST-100S (4) There shall be no residual flux and residual cleaner after cleaning. In the case of using aqueous agent, products shall be dried completely after rinse with de-ionized water in order to remove the cleaner. (5) Other cleaning Please contact us. 11.8 Resin coating The inductance value may change and/or it may affect on the product's performance due to high cure-stress of resin to be used for coating/molding products. So please pay your careful attention when you select resin. In prior to use, please make the reliability evaluation with the product mounted in your application set. MURATA MFG.CO., LTD

Reference Only Spec No. JELF243B-0022L-01 P9/9 11.9 Caution for use There is possibility that the inductance value change due to magnetism. Don‘t use a magnet or a pair of tweezers with magnetism when chip coil are handled. (The tip of the tweezers should be molded with resin or pottery.) 11.10 Magnetic Saturation When the excessive current over rated current is applied, the inductance value may change due to magnetism. 11.11 Handling of a substrate After mounting products on a substrate, do not apply any stress to the product caused by bending or twisting to the substrate when cropping the substrate, inserting and removing a connector from the substrate or tightening screw to the substrate. Excessive mechanical stress may cause cracking in the product. Bending Twisting 11.12 Storage and Handing Requirements (1) Storage period Use the products within 6 months after delivered. Solderability should be checked if this period is exceeded. (2) Storage conditions ・Products should be stored in the warehouse on the following conditions. Temperature ： -10°C to 40°C Humidity ： 15% to 85% relative humidity No rapid change on temperature and humidity Don't keep products in corrosive gases such as sulfur, chlorine gas or acid, or it may cause oxidization of electrode, resulting in poor solderability. ・Products should be stored on the palette for the prevention of the influence from humidity, dust and so on. ・Products should be stored in the warehouse without heat shock, vibration, direct sunlight and so on. ・Products should be stored under the airtight packaged condition. (3) Handling Condition Care should be taken when transporting or handling product to avoid excessive vibration or mechanical shock. 12． ! Note (1) Please make sure that your product has been evaluated in view of your specifications with our product being mounted to your product. (2) You are requested not to use our product deviating from the reference specifications. (3) The contents of this reference specification are subject to change without advance notice. Please approve our product specifications or transact the approval sheet for product specifications before ordering. MURATA MFG.CO., LTD