Reference Only SpecNo.JELF243A-0042N-01 P1/8 CHIP COIL（CHIP INDUCTORS）LQH43CN□□□□03L REFERENCE SPECIFICATION 1.Scope This reference specification applies to LQH43CN Series, Chip coil (Chip Inductors). 2.Part Numbering (ex) LQ H 43 C N 1R0 M 0 3 L Product ID Structure Dimension Applications Category Inductance Tolerance Features Electrode Packaging (L×W) and L:Taping Characteristics 3.Rating Operating Temperature Range -40 to +85°C Storage Temperature Range -40 to +85°C Customer MURATA Inductance DC Self Part Number Part Number (H) Tolerance R(es imstaaxn.c)e RFreesqouneanncty C*Ruarrteendt (%) (MHz min.) (mA) LQH43CN1R0M03L 1.0 0.08 100 1080 LQH43CN1R5M03L 1.5 0.09 85 1000 LQH43CN2R2M03L 2.2 0.11 60 900 M:±20 LQH43CN3R3M03L 3.3 0.13 47 800 LQH43CN4R7M03L 4.7 0.15 35 750 LQH43CN6R8M03L 6.8 0.20 30 720 LQH43CN100K03L 10 0.24 23 650 LQH43CN150K03L 15 0.32 20 570 LQH43CN220K03L 22 0.60 15 420 LQH43CN330K03L 33 1.0 12 310 LQH43CN470K03L 47 1.1 10 280 LQH43CN680K03L 68 K:±10 1.7 8.4 220 LQH43CN101K03L 100 2.2 6.8 190 LQH43CN151K03L 150 3.5 5.5 130 LQH43CN221K03L 220 4.0 4.5 110 LQH43CN331K03L 330 6.8 3.6 100 LQH43CN471K03L 470 8.5 3.0 90 *When applied Rated current to the Products, Inductance will be within ±10% of initial Inductance value. When applied Rated current to the Products, temperature rise caused by self-generated heat shall be limitedto 20°C max.. 4. Testing Conditions <Unless otherwise specified> <In case of doubt> Temperature : Ordinary Temperature (15 to 35°C) Temperature : 20 ± 2°C Humidity : Ordinary Humidity (25 to 85 %(RH)) Humidity : 60 to 70 %(RH) Atmospheric Pressure : 86 to 106 kPa MURATA MFG.CO., LTD

Reference Only SpecNo.JELF243A-0042L-01 P2/8 5.Appearance and Dimensions 3.6±0.2 3.2±0.2 2.6±0.2 3 .2 ±0 .2 ■Unit Mass (Typical value) 4.5±0.3 0.13g ※ Nomarking. in mm) 1.0min.1.0min.1.0min. 6.Electrical Performance No. Item Specification Test Method 6.1 Inductance Inductance shall meet item 3. Measuring Equipment: Agilent 4192A or equivalent Measuring Frequency: 1MHz／1.0 to 330H 1kHz／470H 6.2 DC Resistance DC Resistance shall meet item 3. Measuring Equipment:Digital multi meter 6.3 Self Resonant S.R.F shall meet item 3. Measuring Equipment: Frequency(S.R.F) Agilent 4991A or equivalent 6.4 Rated Current Self temperature rise shall be limited The rated current is applied. to 20°C max. Inductance Change : within ± 10% 7.Mechanical Performance No. Item Specification Test Method 7.1 Shear Test Chip coil shall not be damaged. Substrate:Glass-epoxy substrate Applied Direction : ChipCoil F Force: 20N Substrate Hold Duration: 5±1 s 7.2 Bending Test Substrate: Glass-epoxy substrate (100  40  1.6mm) Speed of Applying Force: 1mm / s Deflection: 2mm Hold Duration: 30 s Pressurejig R340 F Deflection 45 45 Product (in mm) 7.3 Vibration Oscillation Frequency: 10 to 55 to 10Hz for 1 minute Total Amplitude: 1.5mm Testing Time: A period of 2 hours in each of 3 mutually perpendicular directions. (Total 6 hours) MURATA MFG.CO., LTD

Reference Only SpecNo.JELF243A-0042L-01 P3/8 No. Item Specification Test Method 7.4 Solderability The wetting area of the electrode Flux: Ethanol solution of rosin, 25(wt)% shall be at least 90% covered with (Immersed for 5s to 10s) new solder coating. Solder: Sn-3.0Ag-0.5Cu Pre-Heating: 150±10°C / 60 to 90seconds Solder Temperature: 240±5°C Immersion Time: 3±1 s 7.5 Resistance to Appearance:No damage Flux: Ethanol solution of rosin, 25(wt)% Soldering Heat Inductance Change : within ± 5% (Immersed for 5s to 10s) Solder: Sn-3.0Ag-0.5Cu Pre-Heating: 150±10°C / 60 to 90seconds Solder Temperature: 270±5°C Immersion Time: 10±1 s Then measured after exposure in the room condition for 24±2 hours. 8.Environmental Performance (It shall be soldered on the substrate.) No. Item Specification Test Method 8.1 Heat Resistance Appearance:No damage Temperature: 85±2°C Inductance Change : within ±5% Time: 1000± 4 8 hours 0 Then measured after exposure in the room condition for 24±2 hours. 8.2 Cold Resistance Temperature: -40±2°C 48 Time: 1000± 0 hours Then measured after exposure in the room condition for 24±2 hours. 8.3 Humidity Temperature: 40±2°C Humidity: 90 to 95%(RH) Time: 1000± 4 8 hours 0 Then measured after exposure in the room condition for 24±2 hours. 8.4 Temperature 1 cycle: Cycle step 1 : -40±2°C / 30±3 min step 2 : Ordinary temp. / 10 to 15 min step 3 : +85±2°C / 30±3 min step 4 : Ordinary temp. / 10 to 15 min Total of 10 cycles Then measured after exposure in the room condition for 24±2 hours. 9. Specification of Packaging 9.1 Appearance and Dimensions of plastic tape 1 1.5+-00.1 ※Lead-in/out wire 75±0. (00..33±) 0.05 1. 5 5±0.0 ±0.3 ※Thepackingdirectionsofthechipcoil 4.9 .5 12.0 ipnostaitpioinngsaorfethuenilfeieaddwwiitrhe.thein/out 4.0±0.1 8.0±0.1 2.7±0.2 3.6 2.0±0.05 Directionof feed (in mm) Dimension of the Cavity is measured at the bottom side. MURATA MFG.CO., LTD

Reference Only SpecNo.JELF243A-0042L-01 P4/8 9.2 Specification of Taping (1) Packing quantity (standard quantity) 500 pcs / reel (2) Packing Method Products shall be packed in the each embossed cavity of plastic tape and sealed by cover tape. (3) Sprocket hole The sprocket holes are to the right as the tape is pulled toward the user. (4) Spliced point Plastic tape and Cover tape has no spliced point. (5) Missing components number Missing components number within 0.1 % of the number per reel or 1 pc., whichever is greater, and are not continuous. The specified quantity per reel is kept. 9.3 Pull Strength Embossed carrier tape 10N min. Cover tape 5N min. 9.4 Peeling off force of cover tape 165to180degree Speed of Peeling off 300mm/min F Cover tape 0.2 to 0.7N Peeling off force (minimum value is typical) Plastic tape 9.5 Dimensions of Leader-tape, Trailer and Reel There shall be leader-tape (cover tape) and trailer-tape (empty tape) as follows. Trailer : 160min. Leader 2.0±0.5 190 min 210min Label Emptytape Covertape 13.0±0.2 60±1 0 13.0±10 21.0±0.8 Directionof feed 17.0±1.4 180±03 (inmm) 9.6 Marking for reel Customer part number, MURATA part number, Inspection number(1), RoHS marking(2), Quantity etc ･･･ 1) <Expression of Inspection No.> □□ OOOO  (1) (2) (3) (1) Factory Code (2) Date First digit : Year / Last digit of year Second digit : Month / Jan. to Sep.  1 to 9, Oct. to Dec.  O, N, D Third, Fourth digit : Day (3) Serial No. 2) « Expression of RoHS marking » ROHS – Y (△) (1) (2) (1) RoHS regulation conformity parts. (2) MURATA classification number 9.7 Marking for Outside package (corrugated paper box) Customer name, Purchasing order number, Customer part number, MURATA part number, RoHS marking (2) ,Quantity, etc ･･･ MURATA MFG.CO., LTD

Reference Only SpecNo.JELF243A-0042L-01 P5/8 9.8. Specification of Outer Case Outer Case Dimensions Standard Reel Quantity in Outer Case (mm) (Reel) Label W D H H 186 186 93 4 D Above Outer Case size is typical. It depends on a quantity of an order W 10. Caution Limitation of Applications Please contact us before using our products for the applications listed below which require especially high reliability for the prevention of defects which might directly cause damage to the third party's life, body or property. (1) Aircraft equipment (7) Traffic signal equipment (2) Aerospace equipment (8) Disaster prevention / crime prevention equipment (3)Undersea equipment (9) Data-processing equipment (4)Power plant control equipment (10) Applications of similar complexity and /or reliability requirements (5) Medical equipment to the applications listed in the above (6) Transportation equipment (vehicles, trains, ships, etc.) 11. Notice This product is designed for solder mounting. Please consult us in advance for applying other mounting method such as conductive adhesive. 11.1 Land pattern designing Recommended land patterns for flow and reflow soldering are as follows: These have been designed for Electric characteristics and solderability. Please follow the recommended patterns. Otherwise, their performance which includes electrical performance or solderability may be affected, or result to "position shift" in soldering process. Flow Soldering Reflow Soldering * 7.5 ChipCoil 7.5 Land Solder Resist 0 5 1.5 3. 1. 1.5 1.5 1.5 1.5 (in mm) * Applicable to flow soldering. 11.2 Flux, Solder ・Use rosin-based flux. ・Don’t use highly acidic flux with halide content exceeding 0.2(wt)% (chlorine conversion Flux value). ・ Don’t use water-soluble flux. ・Use Sn-3.0Ag-0.5Cu solder Solder ・Standard thickness of solder paste : 200μm to 300μm Other flux (except above) Please contact us for details, then use. MURATA MFG.CO., LTD

Reference Only SpecNo.JELF243A-0042L-01 P6/8 11.3 Flow soldering conditions / Reflow soldering conditions  Pre-heating should be in such a way that the temperature difference between solder and product surface is limited to 150°C max. Cooling into solvent after soldering also should be in such a way that the temperature difference is limited to 100°C max. Insufficient pre-heating may cause cracks on the product, resulting in the deterioration of product quality. Standard soldering profile and the limit soldering profile is as follows. The excessive limit soldering conditions may cause leaching of the electrode and / or resultingin the deterioration of product quality. soldering profile (1)Flow soldering profile T em p . (℃) 265℃±3℃ 250℃ Limit Profile 150 Heating Time Standard Profile 60s min. Time.(s) Standard Profile Limit Profile Pre-heating 150℃、60s min. Heating 250℃、4s～6s 265℃±3℃、5s Cycle of flow 2 times 1 time (2)Reflow soldering profile Temp. 260℃ (℃) 245℃±3℃ 230℃ 220℃ Limit Profile 180 150 30s～60s Standard Profile 60s max. 90s±30s Time.(s) Standard Profile Limit Profile Pre-heating 150～180°C 、90s±30s Heating above 220°C、30s～60s above 230°C、60s max. Peak temperature 245±3°C 260°C,10s Cycle of reflow 2 times 1 time MURATA MFG.CO., LTD

Reference Only SpecNo.JELF243A-0042L-01 P7/8 11.4 Reworking with soldering iron. The following conditions must be strictly followed when using a soldering iron. Pre-heating 150°C,1 min Tip temperature 350°C max. Soldering iron output 80W max. Tip diameter 3mm max. Soldering time 3(+1,-0)s Times 2 times Note : Do not directly touch the products with the tip of the soldering iron in order to prevent the crack on the products due to the thermal shock. 11.5 Solder Volume  Solder shall be used not to be exceeded the upper limits as shown below.  Accordingly increasing the solder volume, the mechanical stress to Chip is also increased. Exceeding solder volume may cause the failure of mechanical or electrical performance. UpperLimit Recommendable T t 1/3T≦ t ≦T (T: Lower flange thickness) 11.6 Product's location The following shall be considered when designing and laying out P.C.B.'s. (1) P.C.B. shall be designed so that products are not subject to the mechanical stress due to warping the board. ［Products direction］ a Products shall be locatedin the sideways b direction (Length:ab) to the mechanical stress. 〈Poor example〉 〈Good example〉 (2) Products location on P.C.B. separation Products (A,B,C,D) shall be located carefully C Seam B so that products are not subject to the mechanical stress due to warping the board. Because they may be subjected the mechanical b A D stress in order of ACB  D. Slit Length:ab a 11.7 Cleaning Conditions Products shall be cleaned on the following conditions. (1) Cleaning temperature shall be limited to 60°C max.(40°C max for IPA.) (2) Ultrasonic cleaning shall comply with the following conditions with avoiding the resonance phenomenon at the mounted products and P.C.B. Power : 20 W /l max. Frequency : 28kHz to 40kHz Time : 5 minutes max. (3) Cleaner 1. Alternative cleaner ･Isopropyl alcohol (IPA) 2. Aqueous agent ･PINE ALPHA ST-100S (4) There shall be no residual flux and residual cleaner after cleaning. In the case of using aqueous agent, products shall be dried completely after rinse with de-ionized water in order to remove the cleaner. (5) Other cleaning Please contact us. MURATA MFG.CO., LTD

Reference Only SpecNo.JELF243A-0042L-01 P8/8 11.8 Resin coating The inductance value may change due to high cure-stress of resin to be used for coating/molding products. An open circuit issue may occur by mechanical stress caused by the resin, amount/cured shape of resin, or operating condition etc. Some resin contains some impurities or chloride possible to generate chlorine by hydrolysis under some operating condition may cause corrosion of wire of coil, leading to open circuit. So, please pay your careful attention when you select resin in case of coating/molding the products with the resin. Prior to use the coating resin, please make sure no reliability issue is observed by evaluating products mounted on your board. 11.9 Caution for use ・Sharp material such as a pair of tweezers or other material such as bristles of cleaning brush, shall not be touched to the winding portion to prevent the breaking of wire. ・Mechanical shock should not be applied to the products mounted on the board to prevent the breaking of the core. 11.10 Handling of a substrate After mounting products on a substrate, do not apply any stress to the product caused by bending or twisting to the substrate when cropping the substrate, inserting and removing a connector from the substrate or tightening screw to the substrate. Excessive mechanical stress may cause cracking in the product. Bending Twisting 11.11 Storage and Handling Requirements (1) Storage period Use the products within 12 months after delivered. Solderability should be checked if this period is exceeded. (2) Storage conditions  Products should be stored in the warehouse on the following conditions. Temperature : -10 ~ 40°C Humidity : 15 to 85% relative humidity No rapid change on temperature and humidity The electrode of the products is coated with solder. Don't keep products in corrosive gases such as sulfur, chlorine gas or acid, or it may cause oxidization of electrode, resulting in poor solderability.  Products should not be stored on bulk packaging condition to prevent the chipping of the core and the breaking of winding wire caused by the collision between the products.  Products should be stored on the palette for the prevention of the influence from humidity, dust and so on.  Products should be stored in the warehouse without heat shock, vibration, direct sunlight and so on. (3) Handling Condition Care should be taken when transporting or handling product to avoid excessive vibration or mechanical shock. 12． Note (1) Please make sure that your product has been evaluated in view of your specifications with our product being mounted to your product. (2) You are requested not to use our product deviating from the reference specifications. (3) The contents of this reference specification are subject to change without advance notice. Please approve our product specifications or transact the approval sheet for product specifications before ordering. MURATA MFG.CO., LTD